diff options
-rw-r--r-- | drivers/net/bnx2x/bnx2x_link.c | 95 | ||||
-rw-r--r-- | drivers/net/bnx2x/bnx2x_link.h | 8 | ||||
-rw-r--r-- | drivers/net/bnx2x/bnx2x_main.c | 103 |
3 files changed, 108 insertions, 98 deletions
diff --git a/drivers/net/bnx2x/bnx2x_link.c b/drivers/net/bnx2x/bnx2x_link.c index bb42104..72ac8dc 100644 --- a/drivers/net/bnx2x/bnx2x_link.c +++ b/drivers/net/bnx2x/bnx2x_link.c @@ -2079,7 +2079,7 @@ static u8 bnx2x_init_xgxs(struct bnx2x_phy *phy, return rc; } /*****************************************************************************/ -/* External Phy section */ +/* External Phy section */ /*****************************************************************************/ void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port) { @@ -3271,6 +3271,8 @@ static u8 bnx2x_8726_config_init(struct bnx2x_phy *phy, struct link_vars *vars) { struct bnx2x *bp = params->bp; + u32 val; + u32 swap_val, swap_override, aeu_gpio_mask, offset; DP(NETIF_MSG_LINK, "Initializing BCM8726\n"); /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, @@ -3351,6 +3353,31 @@ static u8 bnx2x_8726_config_init(struct bnx2x_phy *phy, MDIO_PMA_REG_8726_TX_CTRL2, phy->tx_preemphasis[1]); } + + /* Set GPIO3 to trigger SFP+ module insertion/removal */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3, + MISC_REGISTERS_GPIO_INPUT_HI_Z, params->port); + + /* The GPIO should be swapped if the swap register is set and active */ + swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); + swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); + + /* Select function upon port-swap configuration */ + if (params->port == 0) { + offset = MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0; + aeu_gpio_mask = (swap_val && swap_override) ? + AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1 : + AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0; + } else { + offset = MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0; + aeu_gpio_mask = (swap_val && swap_override) ? + AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 : + AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1; + } + val = REG_RD(bp, offset); + /* add GPIO3 to group */ + val |= aeu_gpio_mask; + REG_WR(bp, offset, val); return 0; } @@ -4888,10 +4915,9 @@ u8 bnx2x_test_link(struct link_params *params, struct link_vars *vars) } static u8 bnx2x_link_initialize(struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { struct bnx2x *bp = params->bp; - u8 port = params->port; u8 rc = 0; u8 phy_index, non_ext_phy; struct bnx2x_phy *ext_phy = ¶ms->phy[EXT_PHY1]; @@ -4964,10 +4990,13 @@ static u8 bnx2x_link_initialize(struct link_params *params, params, vars); } - bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, - (NIG_STATUS_XGXS0_LINK10G | - NIG_STATUS_XGXS0_LINK_STATUS | - NIG_STATUS_SERDES0_LINK_STATUS)); + /* Reset the interrupt indication after phy was initialized */ + bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + + params->port*4, + (NIG_STATUS_XGXS0_LINK10G | + NIG_STATUS_XGXS0_LINK_STATUS | + NIG_STATUS_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); return rc; } @@ -6515,3 +6544,55 @@ void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy) break; } } + +u8 bnx2x_hw_lock_required(struct bnx2x *bp, u32 shmem_base) +{ + u8 phy_index; + struct bnx2x_phy phy; + for (phy_index = INT_PHY; phy_index < MAX_PHYS; + phy_index++) { + if (bnx2x_populate_phy(bp, phy_index, shmem_base, + 0, &phy) != 0) { + DP(NETIF_MSG_LINK, "populate phy failed\n"); + return 0; + } + + if (phy.flags & FLAGS_HW_LOCK_REQUIRED) + return 1; + } + return 0; +} + +u8 bnx2x_fan_failure_det_req(struct bnx2x *bp, + u32 shmem_base, + u8 port) +{ + u8 phy_index, fan_failure_det_req = 0; + struct bnx2x_phy phy; + for (phy_index = EXT_PHY1; phy_index < MAX_PHYS; + phy_index++) { + if (bnx2x_populate_phy(bp, phy_index, shmem_base, + port, &phy) + != 0) { + DP(NETIF_MSG_LINK, "populate phy failed\n"); + return 0; + } + fan_failure_det_req |= (phy.flags & + FLAGS_FAN_FAILURE_DET_REQ); + } + return fan_failure_det_req; +} + +void bnx2x_hw_reset_phy(struct link_params *params) +{ + u8 phy_index; + for (phy_index = EXT_PHY1; phy_index < MAX_PHYS; + phy_index++) { + if (params->phy[phy_index].hw_reset) { + params->phy[phy_index].hw_reset( + ¶ms->phy[phy_index], + params); + params->phy[phy_index] = phy_null; + } + } +} diff --git a/drivers/net/bnx2x/bnx2x_link.h b/drivers/net/bnx2x/bnx2x_link.h index 9717cb1..d663c4f 100644 --- a/drivers/net/bnx2x/bnx2x_link.h +++ b/drivers/net/bnx2x/bnx2x_link.h @@ -311,8 +311,16 @@ void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy); u8 bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy, struct link_params *params, u16 addr, u8 byte_cnt, u8 *o_buf); + +void bnx2x_hw_reset_phy(struct link_params *params); + +/* Checks if HW lock is required for this phy/board type */ +u8 bnx2x_hw_lock_required(struct bnx2x *bp, u32 shmem_base); /* Returns the aggregative supported attributes of the phys on board */ u32 bnx2x_supported_attr(struct link_params *params, u8 phy_idx); /* Probe the phys on board, and populate them in "params" */ u8 bnx2x_phy_probe(struct link_params *params); +/* Checks if fan failure detection is required on one of the phys on board */ +u8 bnx2x_fan_failure_det_req(struct bnx2x *bp, u32 shmem_base, u8 port); + #endif /* BNX2X_LINK_H */ diff --git a/drivers/net/bnx2x/bnx2x_main.c b/drivers/net/bnx2x/bnx2x_main.c index 1184677..0210dde 100644 --- a/drivers/net/bnx2x/bnx2x_main.c +++ b/drivers/net/bnx2x/bnx2x_main.c @@ -1981,7 +1981,7 @@ static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn) { int port = BP_PORT(bp); int reg_offset; - u32 val, swap_val, swap_override; + u32 val; reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 : MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0); @@ -1995,30 +1995,7 @@ static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn) BNX2X_ERR("SPIO5 hw attention\n"); /* Fan failure attention */ - switch (bp->link_params.phy[EXT_PHY1].type) { - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: - /* Low power mode is controlled by GPIO 2 */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW, port); - /* The PHY reset is controlled by GPIO 1 */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, port); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: - /* The PHY reset is controlled by GPIO 1 */ - /* fake the port number to cancel the swap done in - set_gpio() */ - swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); - swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); - port = (swap_val && swap_override) ^ 1; - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, port); - break; - - default: - break; - } + bnx2x_hw_reset_phy(&bp->link_params); bnx2x_fan_failure(bp); } @@ -3867,17 +3844,11 @@ static void bnx2x_setup_fan_failure_detection(struct bnx2x *bp) */ else if (val == SHARED_HW_CFG_FAN_FAILURE_PHY_TYPE) for (port = PORT_0; port < PORT_MAX; port++) { - u32 phy_type = - SHMEM_RD(bp, dev_info.port_hw_config[port]. - external_phy_config) & - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK; is_required |= - ((phy_type == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101) || - (phy_type == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) || - (phy_type == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481)); + bnx2x_fan_failure_det_req( + bp, + bp->common.shmem_base, + port); } DP(NETIF_MSG_HW, "fan detection setting: %d\n", is_required); @@ -4144,17 +4115,8 @@ static int bnx2x_init_common(struct bnx2x *bp) return -EBUSY; } - switch (bp->link_params.phy[EXT_PHY1].type) { - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: - bp->port.need_hw_lock = 1; - break; - - default: - break; - } + bp->port.need_hw_lock = bnx2x_hw_lock_required(bp, + bp->common.shmem_base); bnx2x_setup_fan_failure_detection(bp); @@ -4302,57 +4264,16 @@ static int bnx2x_init_port(struct bnx2x *bp) bnx2x_init_block(bp, MCP_BLOCK, init_stage); bnx2x_init_block(bp, DMAE_BLOCK, init_stage); + bp->port.need_hw_lock = bnx2x_hw_lock_required(bp, + bp->common.shmem_base); - switch (bp->link_params.phy[EXT_PHY1].type) { - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: - { - u32 swap_val, swap_override, aeu_gpio_mask, offset; - - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3, - MISC_REGISTERS_GPIO_INPUT_HI_Z, port); - - /* The GPIO should be swapped if the swap register is - set and active */ - swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); - swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); - - /* Select function upon port-swap configuration */ - if (port == 0) { - offset = MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0; - aeu_gpio_mask = (swap_val && swap_override) ? - AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1 : - AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0; - } else { - offset = MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0; - aeu_gpio_mask = (swap_val && swap_override) ? - AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 : - AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1; - } - val = REG_RD(bp, offset); - /* add GPIO3 to group */ - val |= aeu_gpio_mask; - REG_WR(bp, offset, val); - } - bp->port.need_hw_lock = 1; - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: - bp->port.need_hw_lock = 1; - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: - /* add SPIO 5 to group 0 */ - { + if (bnx2x_fan_failure_det_req(bp, bp->common.shmem_base, + port)) { u32 reg_addr = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 : MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0); val = REG_RD(bp, reg_addr); val |= AEU_INPUTS_ATTN_BITS_SPIO5; REG_WR(bp, reg_addr, val); - } - break; - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: - bp->port.need_hw_lock = 1; - break; - default: - break; } bnx2x__link_reset(bp); |