diff options
Diffstat (limited to 'Documentation/devicetree')
6 files changed, 142 insertions, 34 deletions
diff --git a/Documentation/devicetree/bindings/arc/interrupts.txt b/Documentation/devicetree/bindings/arc/interrupts.txt new file mode 100644 index 0000000..9a5d562 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/interrupts.txt @@ -0,0 +1,24 @@ +* ARC700 incore Interrupt Controller + + The core interrupt controller provides 32 prioritised interrupts (2 levels) + to ARC700 core. + +Properties: + +- compatible: "snps,arc700-intc" +- interrupt-controller: This is an interrupt controller. +- #interrupt-cells: Must be <1>. + + Single Cell "interrupts" property of a device specifies the IRQ number + between 0 to 31 + + intc accessed via the special ARC AUX register interface, hence "reg" property + is not specified. + +Example: + + intc: interrupt-controller { + compatible = "snps,arc700-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index 5bb3dfb..d58675e 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -3,59 +3,61 @@ Required properties: - compatible: "snps,dma-spear1340" - reg: Address range of the DMAC registers -- interrupt-parent: Should be the phandle for the interrupt controller - that services interrupts for this device - interrupt: Should contain the DMAC interrupt number -- nr_channels: Number of channels supported by hardware -- is_private: The device channels should be marked as private and not for by the - general purpose DMA channel allocator. False if not passed. +- dma-channels: Number of channels supported by hardware +- dma-requests: Number of DMA request lines supported, up to 16 +- dma-masters: Number of AHB masters supported by the controller +- #dma-cells: must be <3> - chan_allocation_order: order of allocation of channel, 0 (default): ascending, 1: descending - chan_priority: priority of channels. 0 (default): increase from chan 0->n, 1: increase from chan n->0 - block_size: Maximum block size supported by the controller -- nr_masters: Number of AHB masters supported by the controller - data_width: Maximum data width supported by hardware per AHB master (0 - 8bits, 1 - 16bits, ..., 5 - 256bits) -- slave_info: - - bus_id: name of this device channel, not just a device name since - devices may have more than one channel e.g. "foo_tx". For using the - dw_generic_filter(), slave drivers must pass exactly this string as - param to filter function. - - cfg_hi: Platform-specific initializer for the CFG_HI register - - cfg_lo: Platform-specific initializer for the CFG_LO register - - src_master: src master for transfers on allocated channel. - - dst_master: dest master for transfers on allocated channel. + + +Optional properties: +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- is_private: The device channels should be marked as private and not for by the + general purpose DMA channel allocator. False if not passed. Example: - dma@fc000000 { + dmahost: dma@fc000000 { compatible = "snps,dma-spear1340"; reg = <0xfc000000 0x1000>; interrupt-parent = <&vic1>; interrupts = <12>; - nr_channels = <8>; + dma-channels = <8>; + dma-requests = <16>; + dma-masters = <2>; + #dma-cells = <3>; chan_allocation_order = <1>; chan_priority = <1>; block_size = <0xfff>; - nr_masters = <2>; data_width = <3 3 0 0>; + }; - slave_info { - uart0-tx { - bus_id = "uart0-tx"; - cfg_hi = <0x4000>; /* 0x8 << 11 */ - cfg_lo = <0>; - src_master = <0>; - dst_master = <1>; - }; - spi0-tx { - bus_id = "spi0-tx"; - cfg_hi = <0x2000>; /* 0x4 << 11 */ - cfg_lo = <0>; - src_master = <0>; - dst_master = <0>; - }; - }; +DMA clients connected to the Designware DMA controller must use the format +described in the dma.txt file, using a four-cell specifier for each channel. +The four cells in order are: + +1. A phandle pointing to the DMA controller +2. The DMA request line number +3. Source master for transfers on allocated channel +4. Destination master for transfers on allocated channel + +Example: + + serial@e0000000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0xe0000000 0x1000>; + interrupts = <0 35 0x4>; + status = "disabled"; + dmas = <&dmahost 12 0 1>, + <&dmahost 13 0 1 0>; + dma-names = "rx", "rx"; }; diff --git a/Documentation/devicetree/bindings/mips/cpu_irq.txt b/Documentation/devicetree/bindings/mips/cpu_irq.txt new file mode 100644 index 0000000..13aa4b6 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cpu_irq.txt @@ -0,0 +1,47 @@ +MIPS CPU interrupt controller + +On MIPS the mips_cpu_intc_init() helper can be used to initialize the 8 CPU +IRQs from a devicetree file and create a irq_domain for IRQ controller. + +With the irq_domain in place we can describe how the 8 IRQs are wired to the +platforms internal interrupt controller cascade. + +Below is an example of a platform describing the cascade inside the devicetree +and the code used to load it inside arch_init_irq(). + +Required properties: +- compatible : Should be "mti,cpu-interrupt-controller" + +Example devicetree: + cpu-irq: cpu-irq@0 { + #address-cells = <0>; + + interrupt-controller; + #interrupt-cells = <1>; + + compatible = "mti,cpu-interrupt-controller"; + }; + + intc: intc@200 { + compatible = "ralink,rt2880-intc"; + reg = <0x200 0x100>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu-irq>; + interrupts = <2>; + }; + + +Example platform irq.c: +static struct of_device_id __initdata of_irq_ids[] = { + { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_intc_init }, + { .compatible = "ralink,rt2880-intc", .data = intc_of_init }, + {}, +}; + +void __init arch_init_irq(void) +{ + of_irq_init(of_irq_ids); +} diff --git a/Documentation/devicetree/bindings/mtd/elm.txt b/Documentation/devicetree/bindings/mtd/elm.txt new file mode 100644 index 0000000..8c1528c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/elm.txt @@ -0,0 +1,16 @@ +Error location module + +Required properties: +- compatible: Must be "ti,am33xx-elm" +- reg: physical base address and size of the registers map. +- interrupts: Interrupt number for the elm. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the elm + +Example: +elm: elm@0 { + compatible = "ti,am3352-elm"; + reg = <0x48080000 0x2000>; + interrupts = <4>; +}; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index dab7847..61c5ec8 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -26,6 +26,9 @@ file systems on embedded devices. - linux,mtd-name: allow to specify the mtd name for retro capability with physmap-flash drivers as boot loader pass the mtd partition via the old device name physmap-flash. + - use-advanced-sector-protection: boolean to enable support for the + advanced sector protection (Spansion: PPB - Persistent Protection + Bits) locking. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/serial/lantiq_asc.txt b/Documentation/devicetree/bindings/serial/lantiq_asc.txt new file mode 100644 index 0000000..5b78591 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/lantiq_asc.txt @@ -0,0 +1,16 @@ +Lantiq SoC ASC serial controller + +Required properties: +- compatible : Should be "lantiq,asc" +- reg : Address and length of the register set for the device +- interrupts: the 3 (tx rx err) interrupt numbers. The interrupt specifier + depends on the interrupt-parent interrupt controller. + +Example: + +asc1: serial@E100C00 { + compatible = "lantiq,asc"; + reg = <0xE100C00 0x400>; + interrupt-parent = <&icu0>; + interrupts = <112 113 114>; +}; |