diff options
Diffstat (limited to 'drivers/net/bnx2x/bnx2x_main.c')
| -rw-r--r-- | drivers/net/bnx2x/bnx2x_main.c | 270 |
1 files changed, 36 insertions, 234 deletions
diff --git a/drivers/net/bnx2x/bnx2x_main.c b/drivers/net/bnx2x/bnx2x_main.c index 174ed8b..1ecff37 100644 --- a/drivers/net/bnx2x/bnx2x_main.c +++ b/drivers/net/bnx2x/bnx2x_main.c @@ -1960,12 +1960,16 @@ static void bnx2x_attn_int_asserted(struct bnx2x *bp, u32 asserted) static inline void bnx2x_fan_failure(struct bnx2x *bp) { int port = BP_PORT(bp); - + u32 ext_phy_config; /* mark the failure */ - bp->link_params.ext_phy_config &= ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK; - bp->link_params.ext_phy_config |= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE; + ext_phy_config = + SHMEM_RD(bp, + dev_info.port_hw_config[port].external_phy_config); + + ext_phy_config &= ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK; + ext_phy_config |= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE; SHMEM_WR(bp, dev_info.port_hw_config[port].external_phy_config, - bp->link_params.ext_phy_config); + ext_phy_config); /* log the failure */ netdev_err(bp->dev, "Fan Failure on Network Controller has caused" @@ -1991,7 +1995,7 @@ static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn) BNX2X_ERR("SPIO5 hw attention\n"); /* Fan failure attention */ - switch (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config)) { + switch (bp->link_params.phy[EXT_PHY1].type) { case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: /* Low power mode is controlled by GPIO 2 */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, @@ -4140,7 +4144,7 @@ static int bnx2x_init_common(struct bnx2x *bp) return -EBUSY; } - switch (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config)) { + switch (bp->link_params.phy[EXT_PHY1].type) { case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: @@ -4299,7 +4303,7 @@ static int bnx2x_init_port(struct bnx2x *bp) bnx2x_init_block(bp, MCP_BLOCK, init_stage); bnx2x_init_block(bp, DMAE_BLOCK, init_stage); - switch (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config)) { + switch (bp->link_params.phy[EXT_PHY1].type) { case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: { u32 swap_val, swap_override, aeu_gpio_mask, offset; @@ -4480,7 +4484,7 @@ static int bnx2x_init_func(struct bnx2x *bp) /* Reset PCIE errors for debug */ REG_WR(bp, 0x2114, 0xffffffff); REG_WR(bp, 0x2120, 0xffffffff); - + bnx2x_phy_probe(&bp->link_params); return 0; } @@ -6065,194 +6069,32 @@ static void __devinit bnx2x_link_settings_supported(struct bnx2x *bp, u32 switch_cfg) { int port = BP_PORT(bp); - u32 ext_phy_type; - - switch (switch_cfg) { - case SWITCH_CFG_1G: - BNX2X_DEV_INFO("switch_cfg 0x%x (1G)\n", switch_cfg); - - ext_phy_type = - SERDES_EXT_PHY_TYPE(bp->link_params.ext_phy_config); - switch (ext_phy_type) { - case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT: - BNX2X_DEV_INFO("ext_phy_type 0x%x (Direct)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10baseT_Half | - SUPPORTED_10baseT_Full | - SUPPORTED_100baseT_Half | - SUPPORTED_100baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_2500baseX_Full | - SUPPORTED_TP | - SUPPORTED_FIBRE | - SUPPORTED_Autoneg | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); + bp->port.supported = 0; + switch (bp->link_params.num_phys) { + case 1: + bp->port.supported = bp->link_params.phy[INT_PHY].supported; break; - - case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482: - BNX2X_DEV_INFO("ext_phy_type 0x%x (5482)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10baseT_Half | - SUPPORTED_10baseT_Full | - SUPPORTED_100baseT_Half | - SUPPORTED_100baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_TP | - SUPPORTED_FIBRE | - SUPPORTED_Autoneg | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); + case 2: + bp->port.supported = bp->link_params.phy[EXT_PHY1].supported; break; + } - default: - BNX2X_ERR("NVRAM config error. " - "BAD SerDes ext_phy_config 0x%x\n", - bp->link_params.ext_phy_config); + if (!(bp->port.supported)) { + BNX2X_ERR("NVRAM config error. BAD phy config." + "PHY1 config 0x%x\n", + SHMEM_RD(bp, + dev_info.port_hw_config[port].external_phy_config)); return; } + switch (switch_cfg) { + case SWITCH_CFG_1G: bp->port.phy_addr = REG_RD(bp, NIG_REG_SERDES0_CTRL_PHY_ADDR + port*0x10); BNX2X_DEV_INFO("phy_addr 0x%x\n", bp->port.phy_addr); break; case SWITCH_CFG_10G: - BNX2X_DEV_INFO("switch_cfg 0x%x (10G)\n", switch_cfg); - - ext_phy_type = - XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config); - switch (ext_phy_type) { - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: - BNX2X_DEV_INFO("ext_phy_type 0x%x (Direct)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10baseT_Half | - SUPPORTED_10baseT_Full | - SUPPORTED_100baseT_Half | - SUPPORTED_100baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_2500baseX_Full | - SUPPORTED_10000baseT_Full | - SUPPORTED_TP | - SUPPORTED_FIBRE | - SUPPORTED_Autoneg | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: - BNX2X_DEV_INFO("ext_phy_type 0x%x (8072)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10000baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_FIBRE | - SUPPORTED_Autoneg | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: - BNX2X_DEV_INFO("ext_phy_type 0x%x (8073)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10000baseT_Full | - SUPPORTED_2500baseX_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_FIBRE | - SUPPORTED_Autoneg | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: - BNX2X_DEV_INFO("ext_phy_type 0x%x (8705)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10000baseT_Full | - SUPPORTED_FIBRE | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: - BNX2X_DEV_INFO("ext_phy_type 0x%x (8706)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10000baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_FIBRE | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: - BNX2X_DEV_INFO("ext_phy_type 0x%x (8726)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10000baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_Autoneg | - SUPPORTED_FIBRE | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: - BNX2X_DEV_INFO("ext_phy_type 0x%x (8727)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10000baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_Autoneg | - SUPPORTED_FIBRE | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: - BNX2X_DEV_INFO("ext_phy_type 0x%x (SFX7101)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10000baseT_Full | - SUPPORTED_TP | - SUPPORTED_Autoneg | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481: - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: - BNX2X_DEV_INFO("ext_phy_type 0x%x (BCM848xx)\n", - ext_phy_type); - - bp->port.supported |= (SUPPORTED_10baseT_Half | - SUPPORTED_10baseT_Full | - SUPPORTED_100baseT_Half | - SUPPORTED_100baseT_Full | - SUPPORTED_1000baseT_Full | - SUPPORTED_10000baseT_Full | - SUPPORTED_TP | - SUPPORTED_Autoneg | - SUPPORTED_Pause | - SUPPORTED_Asym_Pause); - break; - - case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: - BNX2X_ERR("XGXS PHY Failure detected 0x%x\n", - bp->link_params.ext_phy_config); - break; - - default: - BNX2X_ERR("NVRAM config error. " - "BAD XGXS ext_phy_config 0x%x\n", - bp->link_params.ext_phy_config); - return; - } - bp->port.phy_addr = REG_RD(bp, NIG_REG_XGXS0_CTRL_PHY_ADDR + port*0x18); BNX2X_DEV_INFO("phy_addr 0x%x\n", bp->port.phy_addr); @@ -6264,8 +6106,6 @@ static void __devinit bnx2x_link_settings_supported(struct bnx2x *bp, bp->port.link_config); return; } - bp->link_params.phy_addr = bp->port.phy_addr; - /* mask what we support according to speed_cap_mask */ if (!(bp->link_params.speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)) @@ -6309,25 +6149,10 @@ static void __devinit bnx2x_link_settings_requested(struct bnx2x *bp) bp->link_params.req_line_speed = SPEED_AUTO_NEG; bp->port.advertising = bp->port.supported; } else { - u32 ext_phy_type = - XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config); - - if ((ext_phy_type == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) || - (ext_phy_type == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706)) { /* force 10G, no AN */ bp->link_params.req_line_speed = SPEED_10000; - bp->port.advertising = - (ADVERTISED_10000baseT_Full | + bp->port.advertising = (ADVERTISED_10000baseT_Full | ADVERTISED_FIBRE); - break; - } - BNX2X_ERR("NVRAM config error. " - "Invalid link_config 0x%x" - " Autoneg not supported\n", - bp->port.link_config); - return; } break; @@ -6475,27 +6300,13 @@ static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp) int port = BP_PORT(bp); u32 val, val2; u32 config; - u16 i; - u32 ext_phy_type; + u32 ext_phy_type, ext_phy_config;; bp->link_params.bp = bp; bp->link_params.port = port; bp->link_params.lane_config = SHMEM_RD(bp, dev_info.port_hw_config[port].lane_config); - bp->link_params.ext_phy_config = - SHMEM_RD(bp, - dev_info.port_hw_config[port].external_phy_config); - /* BCM8727_NOC => BCM8727 no over current */ - if (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config) == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC) { - bp->link_params.ext_phy_config &= - ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK; - bp->link_params.ext_phy_config |= - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727; - bp->link_params.feature_config_flags |= - FEATURE_CONFIG_BCM8727_NOC; - } bp->link_params.speed_cap_mask = SHMEM_RD(bp, @@ -6504,18 +6315,6 @@ static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp) bp->port.link_config = SHMEM_RD(bp, dev_info.port_feature_config[port].link_config); - /* Get the 4 lanes xgxs config rx and tx */ - for (i = 0; i < 2; i++) { - val = SHMEM_RD(bp, - dev_info.port_hw_config[port].xgxs_config_rx[i<<1]); - bp->link_params.xgxs_config_rx[i << 1] = ((val>>16) & 0xffff); - bp->link_params.xgxs_config_rx[(i << 1) + 1] = (val & 0xffff); - - val = SHMEM_RD(bp, - dev_info.port_hw_config[port].xgxs_config_tx[i<<1]); - bp->link_params.xgxs_config_tx[i << 1] = ((val>>16) & 0xffff); - bp->link_params.xgxs_config_tx[(i << 1) + 1] = (val & 0xffff); - } /* If the device is capable of WoL, set the default state according * to the HW @@ -6524,14 +6323,14 @@ static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp) bp->wol = (!(bp->flags & NO_WOL_FLAG) && (config & PORT_FEATURE_WOL_ENABLED)); - BNX2X_DEV_INFO("lane_config 0x%08x ext_phy_config 0x%08x" + BNX2X_DEV_INFO("lane_config 0x%08x" " speed_cap_mask 0x%08x link_config 0x%08x\n", bp->link_params.lane_config, - bp->link_params.ext_phy_config, bp->link_params.speed_cap_mask, bp->port.link_config); bp->link_params.switch_cfg |= (bp->port.link_config & PORT_FEATURE_CONNECTED_SWITCH_MASK); + bnx2x_phy_probe(&bp->link_params); bnx2x_link_settings_supported(bp, bp->link_params.switch_cfg); bnx2x_link_settings_requested(bp); @@ -6540,14 +6339,17 @@ static void __devinit bnx2x_get_port_hwinfo(struct bnx2x *bp) * If connected directly, work with the internal PHY, otherwise, work * with the external PHY */ - ext_phy_type = XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config); + ext_phy_config = + SHMEM_RD(bp, + dev_info.port_hw_config[port].external_phy_config); + ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config); if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) - bp->mdio.prtad = bp->link_params.phy_addr; + bp->mdio.prtad = bp->port.phy_addr; else if ((ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) && (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)) bp->mdio.prtad = - XGXS_EXT_PHY_ADDR(bp->link_params.ext_phy_config); + XGXS_EXT_PHY_ADDR(ext_phy_config); val2 = SHMEM_RD(bp, dev_info.port_hw_config[port].mac_upper); val = SHMEM_RD(bp, dev_info.port_hw_config[port].mac_lower); |