| Age | Commit message (Collapse) | Author |
|---|
|
linux-net@vger.kernel.org was replaced by netdev@oss.sgi.com was replaced
by netdev@vger.kernel.org.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename functions in include/net/ll_poll.h to busy wait.
Clarify documentation about expected power use increase.
Rename POLL_LL to POLL_BUSY_LOOP.
Add need_resched() testing to poll/select busy loops.
Note, that in select and poll can_busy_poll is dynamic and is
updated continuously to reflect the existence of supported
sockets with valid queue information.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds dt support to dwmac version 3.610 and 3.710 these
versions are integrated in STiH415 and STiH416 ARM A9 SOCs.
To support these IP version, some of the device tree properties are
extended.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to avoid making code that deals with printing both, IPv4 and
IPv6 addresses, unnecessary complicated as for example ...
if (sa.sa_family == AF_INET6)
printk("... %pI6 ...", ..sin6_addr);
else
printk("... %pI4 ...", ..sin_addr.s_addr);
... it would be better to introduce a format specifier that can deal
with those kind of situations internally; just as we have a "struct
sockaddr" for generic mapping into "struct sockaddr_in" or "struct
sockaddr_in6" as e.g. done in "union sctp_addr". Then, we could
reduce the above statement into something like:
printk("... %pIS ..", &sockaddr);
In case our pointer is NULL, pointer() then deals with that already at
an earlier point in time internally. While we're at it, support for both
%piS/%pIS, where 'S' stands for sockaddr, comes (almost) for free.
Additionally to that, postfix specifiers 'p', 'f' and 's' are supported
as suggested and initially implemented in 2009 by Joe Perches [1].
Handling of those additional specifiers orientate on the initial RFC that
was proposed. Also we support IPv6 compressed format specified by 'c' and
various other IPv4 extensions as stated in the documentation part.
Likely, there are many other areas than just SCTP in the kernel to make
use of this extension as well.
[1] http://patchwork.ozlabs.org/patch/31480/
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
CC: Joe Perches <joe@perches.com>
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
The following batch contains Netfilter/IPVS updates for net-next,
they are:
* Enforce policy to several nfnetlink subsystem, from Daniel
Borkmann.
* Use xt_socket to match the third packet (to perform simplistic
socket-based stateful filtering), from Eric Dumazet.
* Avoid large timeout for picked up from the middle TCP flows,
from Florian Westphal.
* Exclude IPVS from struct net if IPVS is disabled and removal
of unnecessary included header file, from JunweiZhang.
* Release SCTP connection immediately under load, to mimic current
TCP behaviour, from Julian Anastasov.
* Replace and enhance SCTP state machine, from Julian Anastasov.
* Add tweak to reduce sync traffic in the presence of persistence,
also from Julian Anastasov.
* Add tweak for the IPVS SH scheduler not to reject connections
directed to a server, choose a new one instead, from Alexander
Frolkin.
* Add support for sloppy TCP and SCTP modes, that creates state
information on any packet, not only initial handshake packets,
from Alexander Frolkin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Pull networking fixes from David Miller:
1) Found via trinity:
If you connect up an ipv6 socket to an ipv4 mapped address then an
ipv6 one, sendmsg() can croak because ip6_sk_dst_check() assumes the
route cached in the socket is an ipv6 one. In this case there is an
ipv4 route attached, so it gets stomped on.
Reported by Dave Jones and Hannes Frederic Sowa, fixed by Eric
Dumazet.
2) AF_KEY notifications leak some kernel memory to userspace, fix from
Mathias Krause.
3) DLCI calls __dev_get_by_name() without proper locking, and dlci_del
doesn't validate that the device being deleted is actually a DLCI
one. Fixes from Li Zefan.
4) Length check on bluetooth l2cap information responses is wrong, each
response type has a different lenth, so we should make sure it's in
a given range rather than enforce one single valid length. From
Jaganath Kanakkassery.
5) Receive FIFO overflow is really easy to trigger in stress scenerios
in the sh_eth driver, but the event isn't being handled properly at
all. Specifically, the mask of error interrupts doesn't include the
event so we never clear it, resulting in the driver becomming wedged
processing an interrupt that never gets cleared.
Fix from Sergei Shtylyov.
6) qlcnic sleeps while holding a spinlock, use mdelay() instead of
msleep(). From Shahed Shaikh.
7) Missing curly braces causes SIP netfilter NAT module to always drop
packets. Fix from Balazs Peter Odor.
8) ipt_ULOG in netfilter passes the wrong value to timer setup, causing
the timer to dereference crap when it fires. Fix from Gao Feng.
9) Missing RCU protection around txq->axq_acq traversal in
ath_txq_schedule(). Fix from Felix Fietkau.
10) Idle state transition test in ath9k_htc_config() is reversed, fix
from Sujith Manoharan.
11) IPV6 forwarding handles unicast Router Alert packets incorrectly.
It tests the wrong option state. Previously opt->ra being non-zero
indicated a router alert marking in the SKB, but now it's indicated
by a bit in opt->flags. Fix from YOSHIFUJI Hideaki.
12) SKB leak in GRE tunnel GSO handling, from Eric Dumazet.
13) get_user_pages_fast() error handling in TUN and MACVTAP use the same
local variable for the base index and the loop iterator for page
traversal, oops! Fix from Michael S Tsirkin.
14) ipv6_get_lladdr() can fail, and we must therefore check it's return
value in inet6_set_iftoken(). For from Hannes Frederic Sowa.
15) If you change an interface name and meanwhile can sneak in something
that looks up the name (like SO_BINDTODEVICE or SIOCGIFNAME) we can
deadlock with CONFIG_PREEMPT=n. Fix this by providing a helper
function that properly uses raw_seqcount_begin(). From Nicolas
Schichan.
16) Chain noise calibration test is inverted in iwlwifi, fix from
Nikolay Martynov.
17) Properly set TX iwlwifi descriptor flags for back requests. Fix
from Emmanuel Grumbach.
18) We can't assume skb_transport_header() is set in xt_TCPOPTSTRAP
module, fix from Pablo Neira Ayuso.
19) Some crummy APs don't provide the proper High Throughput info in
association response frames. Add a workaround by assume we'll use
whatever is in the beacon/probe. Fix from Johannes Berg.
20) mac80211 call to rate_idx_match_mask() swaps two arguments (mask and
channel width). Fix from Simon Wunderlich.
21) xt_TCPMSS (like xt_TCPOPTSTRAP) must not try to handle fragmented
frames. Fix from Phil Oester.
22) Fix rate control regression causing iwlwifi/iwlegacy chips to use
1Mbit/s on pre-11n networks. From Moshe Benji and Stanslaw Gruszka.
23) Disable brcmsmac power-save functions, they cause regressions. From
Arend van Spriel.
24) Enforce a sane minimum MTU in l2cap_build_cmd() otherwise we can
easily crash. Fix from Anderson Lizardo.
25) If a learning packet arrives during vxlan_stop() we crash, easily
fixed by checking netif_running(). From Stephen Hemminger.
26) Static vxlan FDB entries should not be migrated, also from Stephen.
27) skb_clone() failures not handled in vxlan_xmit(), oops. Also from
Stephen.
28) Add minimal driver for AR816x/AR817x ethernet chips, from Johannes
Berg.
29) Fix regression in userspace VLAN acceleration control, added by the
802.1ad support changes. Fix from Fernando Luis Vazquez Cao.
30) Interval selection for MLD queries in the bridging code was
reversed. Fix from Linus Lüssing.
31) ipv6's ndisc_send_redirect() erroneously writes to the packet we
received not the packet we are building to send out. Fix from
Matthias Schiffer.
32) Don't free netdev before unregistering it, in usb_8dev can driver.
From Marc Kleine-Budde.
33) Fix nl80211 attribute buffer races, from Johannes Berg.
34) Although netlink_diag.h is under uapi/ it isn't present in Kbuild.
From Stephen Hemminger.
35) Wrong address and family passed to MD5 key lookups in TCP, from
Aydin Arik.
36) phy_type attribute created by SFC driver should not be writable.
From Ben Hutchings.
37) Receive/Transmit queue allocations in pxa168_eth and mv643xx_eth
should use kzalloc(). Otherwise if setup fails half-way, we'll
dereference garbage when trying to teardown the rings. From Lubomir
Rintel.
38) Fix double-allocation of dst (resulting in unfreeable net device) in
ipv6's init_loopback(). From Gao Feng.
39) Fix fragmentation handling SKB leak in netfilter conntrack, we were
freeing the wrong skb pointer. From Phil Oester.
40) Don't report "-1" (SPEED_UNKNOWN) in bond_miimon_commit(), from
Nikolay Aleksandrov.
41) davinci_cpdma doesn't check for DMA mapping errors, letting the
device scribble to random addresses. From Sebastian Siewior.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
dlci: validate the net device in dlci_del()
dlci: acquire rtnl_lock before calling __dev_get_by_name()
af_key: fix info leaks in notify messages
ipv6: ip6_sk_dst_check() must not assume ipv6 dst
net: fix kernel deadlock with interface rename and netdev name retrieval.
net/tg3: Avoid delay during MMIO access
ipv6: check return value of ipv6_get_lladdr
macvtap: fix recovery from gup errors
tun: fix recovery from gup errors
gre: fix a possible skb leak
ipv6: Process unicast packet with Router Alert by checking flag in skb.
ath9k_htc: Handle IDLE state transition properly
ath9k: fix an RCU issue in calling ieee80211_get_tx_rates
netfilter: ipt_ULOG: fix incorrect setting of ulog timer
netfilter: ctnetlink: send event when conntrack label was modified
netfilter: nf_nat_sip: fix mangling
qlcnic: Do not sleep while holding spinlock
drivers: net: cpsw: fix compilation error with cpsw driver
tcp: doc : fix the syncookies default value
sh_eth: fix misreporting of transmit abort
...
|
|
Add sync_persist_mode flag to reduce sync traffic
by syncing only persistent templates.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Currently, we fail only when all of the ips in arp_ip_target are gone.
However, in some situations we might need to fail if even one host from
arp_ip_target becomes unavailable.
All situations, obviously, rely on the idea that we need *completely*
functional network, with all interfaces/addresses working correctly.
One real world example might be:
vlans on top on bond (hybrid port). If bond and vlans have ips assigned
and we have their peers monitored via arp_ip_target - in case of switch
misconfiguration (trunk/access port), slave driver malfunction or
tagged/untagged traffic dropped on the way - we will be able to switch
to another slave.
Though any other configuration needs that if we need to have access to all
arp_ip_targets.
This patch adds this possibility by adding a new parameter -
arp_all_targets (both as a module parameter and as a sysfs knob). It can be
set to:
0 or any (the default) - which works exactly as it's working now -
the slave is up if any of the arp_ip_targets are up.
1 or all - the slave is up if all of the arp_ip_targets are up.
This parameter can be changed on the fly (via sysfs), and requires the mode
to be active-backup and arp_validate to be enabled (it obeys the
arp_validate config on which slaves to validate).
Internally it's done through:
1) Add target_last_arp_rx[BOND_MAX_ARP_TARGETS] array to slave struct. It's
an array of jiffies, meaning that slave->target_last_arp_rx[i] is the
last time we've received arp from bond->params.arp_targets[i] on this
slave.
2) If we successfully validate an arp from bond->params.arp_targets[i] in
bond_validate_arp() - update the slave->target_last_arp_rx[i] with the
current jiffies value.
3) When getting slave's last_rx via slave_last_rx(), we return the oldest
time when we've received an arp from any address in
bond->params.arp_targets[].
If the value of arp_all_targets == 0 - we still work the same way as
before.
Also, update the documentation to reflect the new parameter.
v3->v4:
Kill the forgotten rtnl_unlock(), rephrase the documentation part to be
more clear, don't fail setting arp_all_targets if arp_validate is not set -
it has no effect anyway but can be easier to set up. Also, print a warning
if the last arp_ip_target is removed while the arp_interval is on, but not
the arp_validate.
v2->v3:
Use _bh spinlock, remove useless rtnl_lock() and use jiffies for new
arp_ip_target last arp, instead of slave_last_rx(). On bond_enslave(),
use the same initialization value for target_last_arp_rx[] as is used
for the default last_arp_rx, to avoid useless interface flaps.
Also, instead of failing to remove the last arp_ip_target just print a
warning - otherwise it might break existing scripts.
v1->v2:
Correctly handle adding/removing hosts in arp_ip_target - we need to
shift/initialize all slave's target_last_arp_rx. Also, don't fail module
loading on arp_all_targets misconfiguration, just disable it, and some
minor style fixes.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add some details to bonding documentation on how backup slave arp
validation works.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
select/poll busy-poll support.
Split sysctl value into two separate ones, one for read and one for poll.
updated Documentation/sysctl/net.txt
Add a new poll flag POLL_LL. When this flag is set, sock_poll will call
sk_poll_ll if possible. sock_poll sets this flag in its return value
to indicate to select/poll when a socket that can busy poll is found.
When poll/select have nothing to report, call the low-level
sock_poll again until we are out of time or we find something.
Once the system call finds something, it stops setting POLL_LL, so it can
return the result to the user ASAP.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver for non-standard on-chip ethernet device ARC EMAC 10/100,
instantiated in some legacy ARC (Synopsys) FPGA Boards such as
ARCAngel4/ML50x.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Joe Perches <joe@perches.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syncookies is on for default since in commit e994b7c901
(tcp: Don't make syn cookies initial setting depend on CONFIG_SYSCTL).
And fix a typo of CONFIG_SYN_COOKIES.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
net/wireless/nl80211.c
|
|
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only driver/device-specific small fixes that are pretty safe to apply:
- USB-audio Android and Logitech webcam fixes
- HD-audio MacBook Air 4,2 quirk
- Complete Dell headset quirk entries that were introduced in 3.10"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add models for Dell headset jacks
ALSA: usb-audio: Fix invalid volume resolution for Logitech HD Webcam c310
ALSA: hda - Fix pin configurations for MacBook Air 4,2
ALSA: usb-audio: work around Android accessory firmware bug
ALSA: hda - Headset mic support for three more machines
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Series of fixes for 3.10. There are some usual driver fixes (mostly
on s5p/exynos playform drivers), plus some fixes at V4L2 core"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (40 commits)
[media] soc_camera: error dev remove and v4l2 call
[media] sh_veu: fix the buffer size calculation
[media] sh_veu: keep power supply until the m2m context is released
[media] sh_veu: invoke v4l2_m2m_job_finish() even if a job has been aborted
[media] v4l2-ioctl: don't print the clips list
[media] v4l2-ctrls: V4L2_CTRL_CLASS_FM_RX controls are also valid radio controls
[media] cx88: fix NULL pointer dereference
[media] DocBook/media/v4l: update version number
[media] exynos4-is: Remove "sysreg" clock handling
[media] exynos4-is: Fix reported colorspace at FIMC-IS-ISP subdev
[media] exynos4-is: Ensure fimc-is clocks are not enabled until properly configured
[media] exynos4-is: Prevent NULL pointer dereference when firmware isn't loaded
[media] s5p-mfc: Add NULL check for allocated buffer
[media] s5p-mfc: added missing end-of-lines in debug messages
[media] s5p-mfc: v4l2 controls setup routine moved to initialization code
[media] s5p-mfc: separate encoder parameters for h264 and mpeg4
[media] s5p-mfc: Remove special clock usage in driver
[media] s5p-mfc: Remove unused s5p_mfc_get_decoded_status_v6() function
[media] v4l2: mem2mem: save irq flags correctly
[media] coda: v4l2-compliance fix: add VIDIOC_CREATE_BUFS support
...
|
|
As per feedback from the netdev community, we change the buffer
overflow protection algorithm in receiving sockets so that it
always respects the nominal upper limit set in sk_rcvbuf.
Instead of scaling up from a small sk_rcvbuf value, which leads to
violation of the configured sk_rcvbuf limit, we now calculate the
weighted per-message limit by scaling down from a much bigger value,
still in the same field, according to the importance priority of the
received message.
To allow for administrative tunability of the socket receive buffer
size, we create a tipc_rmem sysctl variable to allow the user to
configure an even bigger value via sysctl command. It is a size of
three (min/default/max) to be consistent with things like tcp_rmem.
By default, the value initialized in tipc_rmem[1] is equal to the
receive socket size needed by a TIPC_CRITICAL_IMPORTANCE message.
This value is also set as the default value of sk_rcvbuf.
Originally-by: Jon Maloy <jon.maloy@ericsson.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
[Ying: added sysctl variation to Jon's original patch]
Signed-off-by: Ying Xue <ying.xue@windriver.com>
[PG: don't compile sysctl.c if not config'd; add Documentation]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These headset jacks keep coming in on more and more platforms, and
it's possible I don't catch them all. Make it easier to test and
verify by making models.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull block layer fixes from Jens Axboe:
"Outside of bcache (which really isn't super big), these are all
few-liners. There are a few important fixes in here:
- Fix blk pm sleeping when holding the queue lock
- A small collection of bcache fixes that have been done and tested
since bcache was included in this merge window.
- A fix for a raid5 regression introduced with the bio changes.
- Two important fixes for mtip32xx, fixing an oops and potential data
corruption (or hang) due to wrong bio iteration on stacked devices."
* 'for-linus' of git://git.kernel.dk/linux-block:
scatterlist: sg_set_buf() argument must be in linear mapping
raid5: Initialize bi_vcnt
pktcdvd: silence static checker warning
block: remove refs to XD disks from documentation
blkpm: avoid sleep when holding queue lock
mtip32xx: Correctly handle bio->bi_idx != 0 conditions
mtip32xx: Fix NULL pointer dereference during module unload
bcache: Fix error handling in init code
bcache: clarify free/available/unused space
bcache: drop "select CLOSURES"
bcache: Fix incompatible pointer type warning
|
|
Add support for the at91sam9x5-family which must use the shadow
interrupt mask due to a hardware issue (causing RTC_IMR to always be
zero).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 6648bd7e0e62c0c8c03b (ipv4: Add sysctl knob to control
early socket demux) introduced such sysctl, but forgot to add
doc into Documentation/networking/ip-sysctl.txt. This patch adds it.
Basically I grab the doc from the description of commit 41063e9dd11956f2d285
(ipv4: Early TCP socket demux.) and the above commit.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/ath/ath9k/debug.c
net/mac80211/iface.c
|
|
Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The version number was still 3.9: update to 3.10.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Fix from Andy is for dmatest regression reported by Will and Rabin has
fixed runtime ref counting for st_dma40"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmatest: do not allow to interrupt ongoing tests
dmaengine: ste_dma40: fix pm runtime ref counting
|
|
This patch fixes icmp_ignore_bogus_error_responses default value to be 1 instead
of FALSE. It is initialized to 1 in icmp_sk_init().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch simplifies the tpacket_v3 example code a bit by getting rid
of unecessary macro wrappers, removing some debugging code so that it is
more to the point, and also adds a header comment. Now this example code
is the very minimum one needs to start from when dealing with tpacket_v3
and ~100 lines smaller than before.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When user interrupts ongoing transfers the dmatest may end up with console
lockup, oops, or data mismatch. This patch prevents user to abort any ongoing
test.
Documentation is updated accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Merge 'net' into 'net-next' to get the MSG_CMSG_COMPAT
regression fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull more xfs updates from Ben Myers:
"Here are several fixes for filesystems with CRC support turned on:
fixes for quota, remote attributes, and recovery. There is also some
feature work related to CRCs: the implementation of CRCs for the inode
unlinked lists, disabling noattr2/attr2 options when appropriate, and
bumping the maximum number of ACLs.
I would have preferred to defer this last category of items to 3.11.
This would require setting a feature bit for the on-disk changes, so
there is some pressure to get these in 3.10. I believe this
represents the end of the CRC related queue.
- Rework of dquot CRCs
- Fix for remote attribute invalidation of a leaf
- Fix ordering of transaction replay in recovery
- Implement CRCs for inode unlinked list
- Disable noattr2/attr2 mount options when CRCs are enabled
- Bump the limitation of ACL entries for v5 superblocks"
* tag 'for-linus-v3.10-rc5' of git://oss.sgi.com/xfs/xfs:
xfs: increase number of ACL entries for V5 superblocks
xfs: disable noattr2/attr2 mount options for CRC enabled filesystems
xfs: inode unlinked list needs to recalculate the inode CRC
xfs: fix log recovery transaction item reordering
xfs: fix remote attribute invalidation for a leaf
xfs: rework dquot CRCs
|
|
attr2 format is always enabled for v5 superblock filesystems, so the
mount options to enable or disable it need to be cause mount errors.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit d3eaace84e40bf946129e516dcbd617173c1cf14)
|
|
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some kernel-doc fixes for forgotten fields and renamed things.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Adding phy-mode support to cpsw driver and updating the cpsw binding
documentation.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Allwinner A10 has an ethernet controller that seem to be developped
internally by them.
The exact feature set of this controller is unknown, since there is no
public documentation for this IP, and this driver is mostly the one
published by Allwinner that has been heavily cleaned up.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
transactions
When in an active transaction that takes a signal, we need to be careful with
the stack. It's possible that the stack has moved back up after the tbegin.
The obvious case here is when the tbegin is called inside a function that
returns before a tend. In this case, the stack is part of the checkpointed
transactional memory state. If we write over this non transactionally or in
suspend, we are in trouble because if we get a tm abort, the program counter
and stack pointer will be back at the tbegin but our in memory stack won't be
valid anymore.
To avoid this, when taking a signal in an active transaction, we need to use
the stack pointer from the checkpointed state, rather than the speculated
state. This ensures that the signal context (written tm suspended) will be
written below the stack required for the rollback. The transaction is aborted
becuase of the treclaim, so any memory written between the tbegin and the
signal will be rolled back anyway.
For signals taken in non-TM or suspended mode, we use the
normal/non-checkpointed stack pointer.
Tested with 64 and 32 bit signals
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we are emulating an instruction inside an active user transaction that
touches memory, the kernel can't emulate it as it operates in transactional
suspend context. We need to abort these transactions and send them back to
userspace for the hardware to rollback.
We can service these if the user transaction is in suspend mode, since the
kernel will operate in the same suspend context.
This adds a check to all alignment faults and to specific instruction
emulations (only string instructions for now). If the user process is in an
active (non-suspended) transaction, we abort the transaction go back to
userspace allowing the HW to roll back the transaction and tell the user of the
failure. This also adds new tm abort cause codes to report the reason of the
persistent error to the user.
Crappy test case here http://neuling.org/devel/junkcode/aligntm.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9 only
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds device tree parsing support for the shared driver of mv643xx_eth.
As the bindings are slightly different from current PPC bindings new binding
documentation is also added. Following PPC-style device setup, the shared
driver now also adds port platform_devices and sets up port platform_data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Stephen proposed:
Since bonding supports configuration via iproute (netlink) and sysfs, I think
it is time to purge the old ifenslave code out of Documentation/networking
and update the documentation.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct spelling typo
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge fixes from Andrew Morton:
"A bunch of fixes and one simple fbdev driver which missed the merge
window because people will still talking about it (to no great
effect)."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (30 commits)
aio: fix kioctx not being freed after cancellation at exit time
mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
random: fix accounting race condition with lockless irq entropy_count update
drivers/char/random.c: fix priming of last_data
mm/memory_hotplug.c: fix printk format warnings
nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
drivers/block/brd.c: fix brd_lookup_page() race
fbdev: FB_GOLDFISH should depend on HAS_DMA
drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
auditfilter.c: fix kernel-doc warnings
aio: fix io_getevents documentation
revert "selftest: add simple test for soft-dirty bit"
drivers/leds/leds-ot200.c: fix error caused by shifted mask
mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
linux/kernel.h: fix kernel-doc warning
mm compaction: fix of improper cache flush in migration code
rapidio/tsi721: fix bug in MSI interrupt handling
hfs: avoid crash in hfs_bnode_create
...
|
|
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A simple frame-buffer describes a raw memory region that may be rendered
to, with the assumption that the display hardware has already been set
up to scan out from that buffer.
This is useful in cases where a bootloader exists and has set up the
display hardware, but a Linux driver doesn't yet exist for the display
hardware.
Examples use-cases include:
* The built-in LCD panels on the Samsung ARM chromebook, and Tegra
devices, and likely many other ARM or embedded systems. These cannot
yet be supported using a full graphics driver, since the panel control
should be provided by the CDF (Common Display Framework), which has been
stuck in design/review for quite some time. One could support these
panels using custom SoC-specific code, but there is a desire to use
common infra-structure rather than having each SoC vendor invent their
own code, hence the desire to wait for CDF.
* Hardware for which a full graphics driver is not yet available, and
the path to obtain one upstream isn't yet clear. For example, the
Raspberry Pi.
* Any hardware in early stages of upstreaming, before a full graphics
driver has been tackled. This driver can provide a graphical boot
console (even full X support) much earlier in the upstreaming process,
thus making new SoC or board support more generally useful earlier.
[akpm@linux-foundation.org: make simplefb_formats[] static]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Rob Clark <robclark@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
