Age | Commit message (Collapse) | Author |
|
|
|
For omap1, we'll keep mach/serial.h around for 8250.c hardware
workarounds. For omap2+, we no longer need mach/serial.h and
can make it local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The runtime PM framework assumes that the hardware state of devices
when initialized is disabled. For all omap_devices, we idle/disable
device by default. However, the console uart uses a "no idle" option
during omap_device init in order to allow earlyprintk usage to work
seamlessly during boot.
Because the hardware is left partially enabled after init (whatever
the bootloader settings were), the omap_device should later be fully
initialized (including mux) and the runtime PM framework should be
told that the device is active, and not disabled so that the hardware
state is in sync with runtime PM state.
To fix, after the device has been created/registered, call
omap_device_enable() to finialize init and use pm_runtime_set_active()
to tell the runtime PM core the device is enabled.
Tested on 2420/n810, 3530/Overo, 3530/Beagle, 3730/OveroSTORM,
3730/Beagle-xM, 4460/PandaES.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.
Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.
This is needed for the ARM common zImage support.
[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We must move this for ARM common zImage support.
Note that neither drivers/media/rc/ir-rx51.c or
drivers/media/platform/omap3isp/ispvideo.c need
to include omap-pm.h, so this patch removes the
include for those files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Let's make omap_hwmod local to mach-omap2 for
ARM common zImage support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Let's make omap_device local to mach-omap2 for
ARM common zImage support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-makefile-sparse
smatch and string-wrapping cleanups for the OMAP subarch code.
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.
Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
|
|
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
into cleanup-sparseirq
Changes for GPMC (General Purpose Memory Controller) that take it
closer for being just a regular device driver.
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
|
|
Find and unwrap wrapped strings in the style:
pr_debug("clockdomain: hardware cannot set/clear wake up of "
"%s when %s wakes up\n", clkdm1->name, clkdm2->name);
Keeping these strings contiguous seems to be the current Linux kernel
policy.
The offending lines were found with the following command:
pcregrep -rnM '"\s*$\s*"' arch/arm/*omap*
While here, some messages have been clarified, some pr_warning(
... calls have been converted to pr_warn( ..., and some printk(KERN_*
... have been converted to pr_*.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Resolve the following warnings from smatch:
arch/arm/mach-omap2/gpmc.c:282 gpmc_cs_set_timings() info: why not propagate 'div' from gpmc_cs_calc_divider() instead of -1?
arch/arm/mach-omap2/serial.c:328 omap_serial_init_port() error: 'pdev' dereferencing possible ERR_PTR()
arch/arm/mach-omap2/timer.c:213 omap2_gp_clockevent_init() Error invalid range 4096 to -1
arch/arm/mach-omap2/gpio.c:63 omap2_gpio_dev_init() warn: possible memory leak of 'pdata'
arch/arm/mach-omap2/omap_hwmod.c:1478 _assert_hardreset() warn: assigning -22 to unsigned variable 'ret'
arch/arm/mach-omap2/omap_hwmod.c:1487 _assert_hardreset() warn: 4294963201 is more than 255 (max '(ret)' can be) so this is always the same.
arch/arm/mach-omap2/omap_hwmod.c:1545 _read_hardreset() warn: assigning -22 to unsigned variable 'ret'
arch/arm/mach-omap2/omap_hwmod.c:1554 _read_hardreset() warn: 4294963201 is more than 255 (max '(ret)' can be) so this is always the same.
arch/arm/mach-omap2/dpll3xxx.c:629 omap3_clkoutx2_recalc() error: we previously assumed 'pclk' could be null (see line 627)
arch/arm/mach-omap2/board-n8x0.c:422 n8x0_mmc_late_init() Error invalid range 14 to 13
arch/arm/mach-omap1/leds-h2p2-debug.c:71 h2p2_dbg_leds_event() error: potentially derefencing uninitialized 'fpga'.
arch/arm/plat-omap/mux.c:79 omap_cfg_reg() Error invalid range 4096 to -1
Thanks to Tony Lindgren <tony@atomide.com> for pointing out that BUG()
can be disabled. The changes in the first version that removed the
subsequent return() after BUG() states have been dropped.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
plat/board.h file is now empty - remove it.
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The driver doesn't need to know about its platform_device.
Everything the driver needs can be done through the
struct device pointer. In case we need to use the
OMAP-specific PM function pointers, those can make
sure to find the device's platform_device pointer
so they can find the struct omap_device through
pdev->archdata field.
Tested-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
OMAP hardware doesn't provide a phyisical DTR line, but
some configurations may need a DTR line which tracks whether
the device is open or not.
So allow a gpio to be configured as the DTR line.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of
default uart pads) removed default uart pads that where getting populated
and which was making rx pin wakeup capable. If uart pads were used in
different mode by any other module then it would fail since the default
pads took over all the uart pins forcefully. With removal of default pads
the rx_pad wakeup for console uart while waking up from off mode is broken.
Utilise the mux api available to probe the availability of mux pins
in uart mode and probe for availability of uart pin in mux mode0
if uart is available as uart pin itself then configure rx pin
as wakeup capable.
This patch itself doesn't cater to all boards. Boards using uart rx wakeup
mechanism should ensure the usage of omap_serial_init_port by configuring
required uart ports and pass necessary mux data, till then this probing of
uart pins can cater to enabling of rx pad wakeup to most of the boards.
This patch can also throw some boot warning from _omap_mux_get_by_name
if pin is requested for availability is not present while dynamically probing
the uart pins availability such boot warnings can be addressed only when board
files are patched with omap_serial_init_port calls passing the right pads
needed for a given port.
Discussion Threads for reference:
http://www.spinics.net/lists/linux-omap/msg69859.html
http://www.spinics.net/lists/linux-omap/msg68659.html
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russ Dill <russ.dill@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated to fix compile when CONFIG_OMAP_MUX is not set]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Sparse and cppcheck warning fixes
By Paul Walmsley
via Paul Walmsley (1) and Tony Lindgren (1)
* tag 'omap-cleanup-sparse-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: clean up some cppcheck warnings
ARM: OMAP1: board files: deduplicate and clean some NAND-related code
ARM: OMAP: USB: remove unnecessary sideways include
ARM: OMAP: DMA: use constant array maximum, drop some LCD DMA code
ARM: OMAP: OCM RAM: use memset_io() when clearing SRAM
ARM: OMAP: fix 'using plain integer as NULL pointer' sparse warnings
ARM: OMAP2+: GPMC: resolve type-conversion warning from sparse
ARM: OMAP1: OHCI: use platform_data fn ptr to enable OCPI bus
ARM: OMAP1: OCPI: move to mach-omap1/
ARM: OMAP: add includes for missing prototypes
ARM: OMAP2+: declare file-local functions as static
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This resolves the merge problem with:
drivers/tty/serial/pch_uart.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current serial UART code, while fidling with ocp idlemode bits,
forget about the smart idle wakeup bit even if it is supported by
UART IP block. This will lead to missing the module wakeup on OMAP's
where the smart idle wakeup is supported.
This was the root cause of the console sluggishness issue, I have been
observing on OMAP4 devices and also can be potential reason for some
other UART wakeup issues.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit (7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
wrongly added muxing of default pads for all uarts. This causes
breakage on multiple boards using uart pins for alternate functions.
For example, on zoom3 random oopses can be seen with nfsroot as
the smsc911x ethernet FIFO timings on GPMC bus are controlled
by gpmc_wait2 and gpmc_wait3 pins. This means we can't mux these
pads to uart4 functionality as commit 7496ba3 was doing.
Not all boards tend to use all uarts and most of unused uart pins
are muxed for other purpose. This commit breaks the modules which
where trying to use unused uart pins on their boards.
So remove the default pad muxing. Note that this is not a complete
fix, as we now rely on bootloader set muxing for the uart wake-up
events. Further patching is needed to enable wake-up events for
uarts that are already muxed to uart mode.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Russ Dill <russ.dill@gmail.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated comments to describe oops on zoom3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Several function declarations used only in the files in which they're
declared should include the static keyword, but don't:
arch/arm/mach-omap2/serial.c:248:6: warning: symbol 'cmdline_find_option' was not declared. Should it be static?
arch/arm/mach-omap2/omap-wakeupgen.c:259:6: warning: symbol 'irq_sar_clear' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:878:27: warning: symbol 'rx51_vibra_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:882:27: warning: symbol 'rx51_audio_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:201:29: warning: symbol 'omap_panda_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:393:24: warning: symbol 'omap4_panda_dvi_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:403:12: warning: symbol 'omap4_panda_dvi_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:464:6: warning: symbol 'omap4_panda_display_init' was not declared. Should it be static?
arch/arm/mach-omap2/hsmmc.c:434:6: warning: symbol 'omap_init_hsmmc' was not declared. Should it be static?
arch/arm/mach-omap2/hwspinlock.c:31:12: warning: symbol 'hwspinlocks_init' was not declared. Should it be static?
arch/arm/mach-omap1/timer.c:58:12: warning: symbol 'omap1_dm_timer_init' was not declared. Should it be static?
arch/arm/mach-omap1/fpga.c:90:6: warning: symbol 'innovator_fpga_IRQ_demux' was not declared. Should it be static?
Mark all of these as static.
Thanks to Arnd Bergmann <arnd@arndb.de> for pointing out a typo in the
original patch description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Govindraj R <govindraj.raja@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: David Anders <x0132446@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
commit 2fd149645eb46d261 (ARM: OMAP2+: UART: Remove
omap_uart_can_sleep and add pm_qos) removed the last usage of
'can_sleep' but did not remove the field.
commit 8612bd22f3036974 (ARM: OMAP2+: UART: Avoid console uart idling
during bootup) removed the last non-trivial use of 'pdev'.
So remove these fields and the one trivial use.
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Omap_uart_can_sleep function blocks system wide low power state until
uart is active remove this func and add qos requests to prevent
MPU from transitioning.
Keep qos request to default value which will allow MPU to transition
and while uart baud rate is available calculate the latency value
from the baudrate and use the same to hold constraint while uart clocks
are enabled, and if uart is auto-idled the constraint is updated with
default constraint value allowing MPU to transition.
Qos requests are blocking notifier calls so put these requests to
work queue, also the driver uses irq_safe version of runtime API's
and callbacks can be called in interrupt disabled context.
So to avoid warn on slow path warning while using qos update
API's from runtime callbacks use the qos_work_queue.
During bootup the runtime_resume call backs might not be called and runtime
callback gets called only after uart is idled by setting the autosuspend
timeout. So qos_request from runtime resume callback might not activated during
boot if uart baudrate is calculated during bootup for console uart, so schedule
the qos_work queue once we calc_latency while configuring the uart port.
Flush and complete any pending qos jobs in work queue while suspending.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
If OMAP UART is used as console uart and debug is enabled,
avoid gating of uart clocks to print all debug prints.
If uart clocks are gated then the debug prints from omap_device
framework or hwmod framework can cause uart to enter recursive
pm_runtime calls, which can cause a deadlock over power lock usage.
For example: Say, uart clocks are cut and we get a print from
omap_device_disable stating disabling uart clocks. This print
calls omap_uart driver console_write which will call runtime API
get_sync which means we enter from runtime API put context to
runtime API get context.
--> runtime put (take power lock)
--> print disabling uart clocks
--> call uart console write
--> call get_sync (try to take power lock)
Also any clock enable API call from uart driver should not call any uart
operation until clocks are enabled back. Like get_sync having debug print
calling uart console write even before clocks are enabled.
So to avoid these scenarios, identify from bootargs if OMAP_UART(ttyO) is used
in debug mode. If so, do not set device_may_wakeup. This will prevent
pm_runtime_enable in uart driver and will avoid uart clock gating.
Debug is enabled either by adding debug word in bootarg or by setting
loglevel=10
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
If no_console_suspend is used we have prevent uart idling during suspend
to provide debug prints.
Power domain hooks can idle uarts if left enabled during system wide suspend
so re-use the omap_device_disable_idle_on_suspend API's to ensure console_uart
is not idled during suspend.
omap_device_disable_idle_on_suspend API was used on all uarts since the uart
driver was not runtime adapted, now with runtime adaptation we can re-use this
API only for no_console_suspend use cases.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Omap-uart can be used as console uart to print early boot messages using
earlyprintk so for console uart prevent hwmod reset or idling during bootup.
Identify omap-uart used as console and avoid idling rather than preventing
all omap-uarts from idling during bootup. Update the comments for the same.
Remove the uart idling and enabling back using hwmod_idle/omap_device_enable
for all uarts that where left enabled from boot to set the hwmod framework
state machine right. This need not be taken care any more serial.c rather
can be handled within the hwmod framework.
Reference: http://www.spinics.net/lists/linux-omap/msg60300.html
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Reuse the num_uarts variable itself to count number of uarts.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
When using DMA there are two timeouts defined. The first timeout,
rx_timeout, is really a polling rate in which software polls the
DMA status to see if the DMA has finished. This is necessary for
the RX side because we do not know how much data we will receive.
The secound timeout, RX_TIMEOUT, is a timeout after which the
DMA will be stopped if no more data is received. To make this
clearer, rename rx_timeout as rx_poll_rate and rename the
function serial_omap_rx_timeout() to serial_omap_rxdma_poll().
The OMAP-Serial driver defines an RX_TIMEOUT of 3 seconds that is
used to indicate when the DMA for UART can be stopped if no more
data is received. The value is a global definition that is applied
to all instances of the UART.
Each UART may be used for a different purpose and so the timeout
required may differ. Make this value configurable for each UART so
that this value can be optimised for power savings.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The following UART parameters are defined within the UART driver:
1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
where uart will be disabled after timeout
Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.
This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.
If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
With runtime adaptation done remove clock_enable/disbale API's
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
From the runtime callbacks enable hwmod wakeups for uart which will
internally enable io-pad wakeups for uarts if they have rx-pad pins
set as wakeup capabale.
Use the io-ring wakeup mechanism after uart clock gating and leave
the PM_WKST set for uart to default reset values cleanup the
code in serial.c which was handling PM_WKST reg.
Irq_chaing(PRM_DRIVER) is used to wakeup uart after uart clocks are gated
using pad wakeup mechanism.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.
Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.
Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Avoid unconditional context restore every time we gate uart
clocks. Check whether context loss happened based on which
we can context restore uart regs from uart_port structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Remove the uart reset function which is configuring the
TX empty irq which can now be handled within omap-serial driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Remove context save function from serial.c and move context restore
function to omap-serial. Remove all regs stored in omap_uart_state
for contex_save/restore, reg read write funcs used in context_save/restore,
io_addresses populated for read/write funcs.
Clock gating mechanism was done in serial.c and had no info on uart state
thus we needed context save and restore in serial.c
With runtime conversion and clock gating done within uart driver
context restore can be done from regs value available from uart_omap_port
structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The mapbase (start_address), membase(io_remap cookie) part of
pdata struct omap_uart_port_info are removed as this should be
derived within driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Padconf wakeup is used to wakeup uart after uart fclks/iclks are gated.
Rx-Pad wakeup was done by writing to rx-pad offset value populated in
serial.c idle_init. Remove the direct reading and writing into rx pad.
Remove the padconf field part of omap_uart_state struct and pad offsets
populated.
Now with mux framework support we can use mux_utilities
along with hmwod framework to handle io-pad configuration and enable rx-pad
wake-up mechanism.
To avoid breaking any board support add default mux data for all uart's
if mux info is not passed from board file.
With the default pads populated in serial.c wakeup capability for
rx pads is set, this can be used to enable uart_rx io-pad wakeup from
hwmod framework. The pad values in 3430sdp/4430sdp/omap4panda board file
are same as the default pad values populated in serial.c. Remove pad values
from 3430sdp/4430sdp/omap4panda board file and use the default pads
from serial.c file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Currently we use a shared irq handler to identify uart activity and then
trigger a timer. By default the timeout value is zero and can be set or
modified from sysfs. If there was no uart activity for the period set
through sysfs, the timer will expire and call timer handler this will
set a flag can_sleep using which decision to gate uart clocks can be taken.
Since the clock gating mechanism is outside the uart driver, we currently
use this mechanism. In preparation to runtime implementation for omap-serial
driver we can cleanup this mechanism and use runtime API's to gate uart clocks.
Removes the following:
* timer related info from local uart_state struct
* the code used to set timeout value from sysfs.
* irqflags used to set shared irq handler.
* un-used function omap_uart_check_wakeup.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
We had been using traditional 8250 driver as uart console driver
prior to omap-serial driver. Since we have omap-serial driver
in mainline kernel for some time now it has been used as default
uart console driver on omap2+ platforms. Remove 8250 support for
omap-uarts.
Serial_in and serial_out override for 8250 serial driver is also
removed. Empty fifo read fix is already taken care with omap-serial
driver with data ready bit check from LSR reg before reading RX fifo.
Also waiting for THRE(transmit hold reg empty) is done with wait_for_xmitr
in omap-serial driver.
Serial_in/out overrides are not neceesary for omap-serial driver
and things that are taken with omap-serial driver are removed here.
Remove headers that were necessary to support 8250 support
and remove all config bindings done to keep 8250 backward compatibility
while adding omap-serial driver. Remove omap_uart_reset needed for
8250 autoconf.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.
1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
path from PM code, this is removed as same is handled by
uart_suspend_port/uart_resume_port in omap-serial driver which will
do an port_shutdown on suspend freeing irq and port_startup on resume
enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
UART clocks can be gated within driver using runtime funcs
and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
driver itself with runtime API. Remove is_suspending check used to acquire
console_lock.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove all these duplicated structures since a default one is now
available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Public omap_device functions need to take platform_device pointers,
conversion to omap_device pointers is done internal to the omap_device
layer.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
All of the device init and device driver interaction with omap_device
is done using platform_device pointers. To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.
All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.
This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|