From 63d4a8f963fce8fe5d8ba3d5eba34d7d7ca6f82b Mon Sep 17 00:00:00 2001 From: Matthew Vick Date: Fri, 9 Nov 2012 05:49:54 +0000 Subject: igb: No longer rely on APME to determine WoL settings Historically, we've been using the APME bit to determine whether a device supports wake on a given port or not. However, this bit specifies the default wake setting, rather than the wake support. Change the behavior so that we use a flag to keep the capabilities separate from the enablement while meeting customer requirements. Signed-off-by: Matthew Vick Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher diff --git a/drivers/net/ethernet/intel/igb/igb.h b/drivers/net/ethernet/intel/igb/igb.h index d8fd5b6..c15a481 100644 --- a/drivers/net/ethernet/intel/igb/igb.h +++ b/drivers/net/ethernet/intel/igb/igb.h @@ -370,8 +370,6 @@ struct igb_adapter { u32 eims_other; /* to not mess up cache alignment, always add to the bottom */ - u32 eeprom_wol; - u16 tx_ring_count; u16 rx_ring_count; unsigned int vfs_allocated_count; @@ -401,6 +399,7 @@ struct igb_adapter { #define IGB_FLAG_PTP (1 << 5) #define IGB_FLAG_RSS_FIELD_IPV4_UDP (1 << 6) #define IGB_FLAG_RSS_FIELD_IPV6_UDP (1 << 7) +#define IGB_FLAG_WOL_SUPPORTED (1 << 8) /* DMA Coalescing defines */ #define IGB_MIN_TXPBSIZE 20408 diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c index 0acf590..e2288b5 100644 --- a/drivers/net/ethernet/intel/igb/igb_ethtool.c +++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c @@ -1966,54 +1966,6 @@ static void igb_diag_test(struct net_device *netdev, msleep_interruptible(4 * 1000); } -static int igb_wol_exclusion(struct igb_adapter *adapter, - struct ethtool_wolinfo *wol) -{ - struct e1000_hw *hw = &adapter->hw; - int retval = 1; /* fail by default */ - - switch (hw->device_id) { - case E1000_DEV_ID_82575GB_QUAD_COPPER: - /* WoL not supported */ - wol->supported = 0; - break; - case E1000_DEV_ID_82575EB_FIBER_SERDES: - case E1000_DEV_ID_82576_FIBER: - case E1000_DEV_ID_82576_SERDES: - /* Wake events not supported on port B */ - if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1) { - wol->supported = 0; - break; - } - /* return success for non excluded adapter ports */ - retval = 0; - break; - case E1000_DEV_ID_82576_QUAD_COPPER: - case E1000_DEV_ID_82576_QUAD_COPPER_ET2: - /* quad port adapters only support WoL on port A */ - if (!(adapter->flags & IGB_FLAG_QUAD_PORT_A)) { - wol->supported = 0; - break; - } - /* return success for non excluded adapter ports */ - retval = 0; - break; - default: - /* dual port cards only support WoL on port A from now on - * unless it was enabled in the eeprom for port B - * so exclude FUNC_1 ports from having WoL enabled */ - if ((rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) && - !adapter->eeprom_wol) { - wol->supported = 0; - break; - } - - retval = 0; - } - - return retval; -} - static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) { struct igb_adapter *adapter = netdev_priv(netdev); @@ -2023,10 +1975,7 @@ static void igb_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) WAKE_PHY; wol->wolopts = 0; - /* this function will set ->supported = 0 and return 1 if wol is not - * supported by this hardware */ - if (igb_wol_exclusion(adapter, wol) || - !device_can_wakeup(&adapter->pdev->dev)) + if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED)) return; /* apply any specific unsupported masks here */ @@ -2054,8 +2003,7 @@ static int igb_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) if (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE)) return -EOPNOTSUPP; - if (igb_wol_exclusion(adapter, wol) || - !device_can_wakeup(&adapter->pdev->dev)) + if (!(adapter->flags & IGB_FLAG_WOL_SUPPORTED)) return wol->wolopts ? -EOPNOTSUPP : 0; /* these settings will always override what we currently have */ diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c index 7044aaa..0fe2521 100644 --- a/drivers/net/ethernet/intel/igb/igb_main.c +++ b/drivers/net/ethernet/intel/igb/igb_main.c @@ -1837,7 +1837,6 @@ static int __devinit igb_probe(struct pci_dev *pdev, const struct e1000_info *ei = igb_info_tbl[ent->driver_data]; unsigned long mmio_start, mmio_len; int err, pci_using_dac; - u16 eeprom_apme_mask = IGB_EEPROM_APME; u8 part_str[E1000_PBANUM_LENGTH]; /* Catch broken hardware that put the wrong VF device ID in @@ -2045,28 +2044,27 @@ static int __devinit igb_probe(struct pci_dev *pdev, igb_validate_mdi_setting(hw); - /* Initial Wake on LAN setting If APM wake is enabled in the EEPROM, - * enable the ACPI Magic Packet filter - */ - + /* By default, support wake on port A */ if (hw->bus.func == 0) - hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data); - else if (hw->mac.type >= e1000_82580) + adapter->flags |= IGB_FLAG_WOL_SUPPORTED; + + /* Check the NVM for wake support on non-port A ports */ + if (hw->mac.type >= e1000_82580) hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A + NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1, &eeprom_data); else if (hw->bus.func == 1) hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data); - if (eeprom_data & eeprom_apme_mask) - adapter->eeprom_wol |= E1000_WUFC_MAG; + if (eeprom_data & IGB_EEPROM_APME) + adapter->flags |= IGB_FLAG_WOL_SUPPORTED; /* now that we have the eeprom settings, apply the special cases where * the eeprom may be wrong or the board simply won't support wake on * lan on a particular port */ switch (pdev->device) { case E1000_DEV_ID_82575GB_QUAD_COPPER: - adapter->eeprom_wol = 0; + adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; break; case E1000_DEV_ID_82575EB_FIBER_SERDES: case E1000_DEV_ID_82576_FIBER: @@ -2074,24 +2072,38 @@ static int __devinit igb_probe(struct pci_dev *pdev, /* Wake events only supported on port A for dual fiber * regardless of eeprom setting */ if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1) - adapter->eeprom_wol = 0; + adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; break; case E1000_DEV_ID_82576_QUAD_COPPER: case E1000_DEV_ID_82576_QUAD_COPPER_ET2: /* if quad port adapter, disable WoL on all but port A */ if (global_quad_port_a != 0) - adapter->eeprom_wol = 0; + adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; else adapter->flags |= IGB_FLAG_QUAD_PORT_A; /* Reset for multiple quad port adapters */ if (++global_quad_port_a == 4) global_quad_port_a = 0; break; + default: + /* If the device can't wake, don't set software support */ + if (!device_can_wakeup(&adapter->pdev->dev)) + adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; } /* initialize the wol settings based on the eeprom settings */ - adapter->wol = adapter->eeprom_wol; - device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol); + if (adapter->flags & IGB_FLAG_WOL_SUPPORTED) + adapter->wol |= E1000_WUFC_MAG; + + /* Some vendors want WoL disabled by default, but still supported */ + if ((hw->mac.type == e1000_i350) && + (pdev->subsystem_vendor == PCI_VENDOR_ID_HP)) { + adapter->flags |= IGB_FLAG_WOL_SUPPORTED; + adapter->wol = 0; + } + + device_set_wakeup_enable(&adapter->pdev->dev, + adapter->flags & IGB_FLAG_WOL_SUPPORTED); /* reset the hardware with the new settings */ igb_reset(adapter); -- cgit v0.10.2