From b3f7ed0324091e2cb23fe1b3c10570700f614014 Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Wed, 28 Sep 2011 21:27:52 -0500 Subject: ARM: gic: add OF based initialization This adds ARM gic interrupt controller initialization using device tree data. The initialization function is intended to be called by of_irq_init function like this: const static struct of_device_id irq_match[] = { { .compatible = "arm,cortex-a9-gic", .data = gic_of_init, }, {} }; static void __init init_irqs(void) { of_irq_init(irq_match); } Signed-off-by: Rob Herring Reviewed-by: Jamie Iles Tested-by: Thomas Abraham Acked-by: Grant Likely diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt new file mode 100644 index 0000000..52916b4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -0,0 +1,55 @@ +* ARM Generic Interrupt Controller + +ARM SMP cores are often associated with a GIC, providing per processor +interrupts (PPI), shared processor interrupts (SPI) and software +generated interrupts (SGI). + +Primary GIC is attached directly to the CPU and typically has PPIs and SGIs. +Secondary GICs are cascaded into the upward interrupt controller and do not +have PPIs or SGIs. + +Main node required properties: + +- compatible : should be one of: + "arm,cortex-a9-gic" + "arm,arm11mp-gic" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a and the value shall be 3. + + The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI + interrupts. + + The 2nd cell contains the interrupt number for the interrupt type. + SPI interrupts are in the range [0-987]. PPI interrupts are in the + range [0-15]. + + The 3rd cell is the flags, encoded as follows: + bits[3:0] trigger type and level flags. + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of + the 8 possible cpus attached to the GIC. A bit set to '1' indicated + the interrupt is wired to that CPU. Only valid for PPI interrupts. + +- reg : Specifies base physical address(s) and size of the GIC registers. The + first region is the GIC distributor register base and size. The 2nd region is + the GIC cpu interface register base and size. + +Optional +- interrupts : Interrupt source of the parent interrupt controller. Only + present on secondary GICs. + +Example: + + intc: interrupt-controller@fff11000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0xfff11000 0x1000>, + <0xfff10100 0x100>; + }; + diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c index ccaa1ab..1333e68 100644 --- a/arch/arm/common/gic.c +++ b/arch/arm/common/gic.c @@ -30,6 +30,9 @@ #include #include #include +#include +#include +#include #include #include #include @@ -530,7 +533,33 @@ static void __init gic_pm_init(struct gic_chip_data *gic) } #endif +#ifdef CONFIG_OF +static int gic_irq_domain_dt_translate(struct irq_domain *d, + struct device_node *controller, + const u32 *intspec, unsigned int intsize, + unsigned long *out_hwirq, unsigned int *out_type) +{ + if (d->of_node != controller) + return -EINVAL; + if (intsize < 3) + return -EINVAL; + + /* Get the interrupt number and add 16 to skip over SGIs */ + *out_hwirq = intspec[1] + 16; + + /* For SPIs, we need to add 16 more to get the GIC irq ID number */ + if (!intspec[0]) + *out_hwirq += 16; + + *out_type = intspec[2] & IRQ_TYPE_SENSE_MASK; + return 0; +} +#endif + const struct irq_domain_ops gic_irq_domain_ops = { +#ifdef CONFIG_OF + .dt_translate = gic_irq_domain_dt_translate, +#endif }; void __init gic_init(unsigned int gic_nr, unsigned int irq_start, @@ -608,3 +637,35 @@ void gic_raise_softirq(const struct cpumask *mask, unsigned int irq) writel_relaxed(map << 16 | irq, gic_data[0].dist_base + GIC_DIST_SOFTINT); } #endif + +#ifdef CONFIG_OF +static int gic_cnt __initdata = 0; + +int __init gic_of_init(struct device_node *node, struct device_node *parent) +{ + void __iomem *cpu_base; + void __iomem *dist_base; + int irq; + struct irq_domain *domain = &gic_data[gic_cnt].domain; + + if (WARN_ON(!node)) + return -ENODEV; + + dist_base = of_iomap(node, 0); + WARN(!dist_base, "unable to map gic dist registers\n"); + + cpu_base = of_iomap(node, 1); + WARN(!cpu_base, "unable to map gic cpu registers\n"); + + domain->of_node = of_node_get(node); + + gic_init(gic_cnt, 16, dist_base, cpu_base); + + if (parent) { + irq = irq_of_parse_and_map(node, 0); + gic_cascade_irq(gic_cnt, irq); + } + gic_cnt++; + return 0; +} +#endif diff --git a/arch/arm/include/asm/hardware/gic.h b/arch/arm/include/asm/hardware/gic.h index 43a05d9..0a026b9 100644 --- a/arch/arm/include/asm/hardware/gic.h +++ b/arch/arm/include/asm/hardware/gic.h @@ -40,6 +40,7 @@ extern void __iomem *gic_cpu_base_addr; extern struct irq_chip gic_arch_extn; void gic_init(unsigned int, unsigned int, void __iomem *, void __iomem *); +int gic_of_init(struct device_node *node, struct device_node *parent); void gic_secondary_init(unsigned int); void gic_cascade_irq(unsigned int gic_nr, unsigned int irq); void gic_raise_softirq(const struct cpumask *mask, unsigned int irq); -- cgit v0.10.2