From 582d5fbd4e81e7debe5f3a0e6ce1a0bcdf636c6e Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 20 Jul 2010 19:18:51 +0200 Subject: ARM: at91/pio: add new PIO3 features This patch adds the support for new PIO controller found on some at91sam SOCs. - more peripheral multiplexing - more features to configure on a PIO (pull-down, Schmitt trigger, debouncer) - support for several IRQ triggering features (type and polarity) Support for those new features are retrieved from the device tree compatibility string. Debugfs at91_gpio file is updated to monitor configuration. Signed-off-by: Nicolas Ferre diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt index a7bcaec..66efc80 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -1,7 +1,7 @@ * Atmel GPIO controller (PIO) Required properties: -- compatible: "atmel,at91rm9200-gpio" +- compatible: "atmel,-gpio", where is at91rm9200 or at91sam9x5. - reg: Should contain GPIO controller registers location and length - interrupts: Should be the port interrupt shared by all the pins. - #gpio-cells: Should be two. The first cell is the pin number and diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index bb0c676..a02e636 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -89,7 +89,7 @@ }; pioA: gpio@fffff400 { - compatible = "atmel,at91rm9200-gpio"; + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x100>; interrupts = <2 4>; #gpio-cells = <2>; @@ -98,7 +98,7 @@ }; pioB: gpio@fffff600 { - compatible = "atmel,at91rm9200-gpio"; + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffff600 0x100>; interrupts = <2 4>; #gpio-cells = <2>; @@ -107,7 +107,7 @@ }; pioC: gpio@fffff800 { - compatible = "atmel,at91rm9200-gpio"; + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffff800 0x100>; interrupts = <3 4>; #gpio-cells = <2>; @@ -116,7 +116,7 @@ }; pioD: gpio@fffffa00 { - compatible = "atmel,at91rm9200-gpio"; + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffffa00 0x100>; interrupts = <3 4>; #gpio-cells = <2>; diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c index acbe23c..583b724 100644 --- a/arch/arm/mach-at91/board-dt.c +++ b/arch/arm/mach-at91/board-dt.c @@ -86,6 +86,7 @@ static const struct of_device_id irq_of_match[] __initconst = { { .compatible = "atmel,at91rm9200-aic", .data = at91_aic_of_init }, { .compatible = "atmel,at91rm9200-gpio", .data = at91_gpio_of_irq_setup }, + { .compatible = "atmel,at91sam9x5-gpio", .data = at91_gpio_of_irq_setup }, { /*sentinel*/ } }; diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c index 567df65..325837a 100644 --- a/arch/arm/mach-at91/gpio.c +++ b/arch/arm/mach-at91/gpio.c @@ -76,6 +76,14 @@ static struct at91_gpio_chip gpio_chip[] = { }; static int gpio_banks; +static unsigned long at91_gpio_caps; + +/* All PIO controllers support PIO3 features */ +#define AT91_GPIO_CAP_PIO3 (1 << 0) + +#define has_pio3() (at91_gpio_caps & AT91_GPIO_CAP_PIO3) + +/*--------------------------------------------------------------------------*/ static inline void __iomem *pin_to_controller(unsigned pin) { @@ -92,6 +100,25 @@ static inline unsigned pin_to_mask(unsigned pin) } +static char peripheral_function(void __iomem *pio, unsigned mask) +{ + char ret = 'X'; + u8 select; + + if (pio) { + if (has_pio3()) { + select = !!(__raw_readl(pio + PIO_ABCDSR1) & mask); + select |= (!!(__raw_readl(pio + PIO_ABCDSR2) & mask) << 1); + ret = 'A' + select; + } else { + ret = __raw_readl(pio + PIO_ABSR) & mask ? + 'B' : 'A'; + } + } + + return ret; +} + /*--------------------------------------------------------------------------*/ /* Not all hardware capabilities are exposed through these calls; they @@ -139,7 +166,14 @@ int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup) __raw_writel(mask, pio + PIO_IDR); __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_ASR); + if (has_pio3()) { + __raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask, + pio + PIO_ABCDSR1); + __raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask, + pio + PIO_ABCDSR2); + } else { + __raw_writel(mask, pio + PIO_ASR); + } __raw_writel(mask, pio + PIO_PDR); return 0; } @@ -159,7 +193,14 @@ int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup) __raw_writel(mask, pio + PIO_IDR); __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); - __raw_writel(mask, pio + PIO_BSR); + if (has_pio3()) { + __raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask, + pio + PIO_ABCDSR1); + __raw_writel(__raw_readl(pio + PIO_ABCDSR2) & ~mask, + pio + PIO_ABCDSR2); + } else { + __raw_writel(mask, pio + PIO_BSR); + } __raw_writel(mask, pio + PIO_PDR); return 0; } @@ -167,8 +208,50 @@ EXPORT_SYMBOL(at91_set_B_periph); /* - * mux the pin to the gpio controller (instead of "A" or "B" peripheral), and - * configure it for an input. + * mux the pin to the "C" internal peripheral role. + */ +int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio || !has_pio3()) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(__raw_readl(pio + PIO_ABCDSR1) & ~mask, pio + PIO_ABCDSR1); + __raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2); + __raw_writel(mask, pio + PIO_PDR); + return 0; +} +EXPORT_SYMBOL(at91_set_C_periph); + + +/* + * mux the pin to the "D" internal peripheral role. + */ +int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio || !has_pio3()) + return -EINVAL; + + __raw_writel(mask, pio + PIO_IDR); + __raw_writel(mask, pio + (use_pullup ? PIO_PUER : PIO_PUDR)); + __raw_writel(__raw_readl(pio + PIO_ABCDSR1) | mask, pio + PIO_ABCDSR1); + __raw_writel(__raw_readl(pio + PIO_ABCDSR2) | mask, pio + PIO_ABCDSR2); + __raw_writel(mask, pio + PIO_PDR); + return 0; +} +EXPORT_SYMBOL(at91_set_D_periph); + + +/* + * mux the pin to the gpio controller (instead of "A", "B", "C" + * or "D" peripheral), and configure it for an input. */ int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup) { @@ -188,8 +271,8 @@ EXPORT_SYMBOL(at91_set_gpio_input); /* - * mux the pin to the gpio controller (instead of "A" or "B" peripheral), - * and configure it for an output. + * mux the pin to the gpio controller (instead of "A", "B", "C" + * or "D" peripheral), and configure it for an output. */ int __init_or_module at91_set_gpio_output(unsigned pin, int value) { @@ -219,12 +302,37 @@ int __init_or_module at91_set_deglitch(unsigned pin, int is_on) if (!pio) return -EINVAL; + + if (has_pio3() && is_on) + __raw_writel(mask, pio + PIO_IFSCDR); __raw_writel(mask, pio + (is_on ? PIO_IFER : PIO_IFDR)); return 0; } EXPORT_SYMBOL(at91_set_deglitch); /* + * enable/disable the debounce filter; + */ +int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio || !has_pio3()) + return -EINVAL; + + if (is_on) { + __raw_writel(mask, pio + PIO_IFSCER); + __raw_writel(div & PIO_SCDR_DIV, pio + PIO_SCDR); + __raw_writel(mask, pio + PIO_IFER); + } else { + __raw_writel(mask, pio + PIO_IFDR); + } + return 0; +} +EXPORT_SYMBOL(at91_set_debounce); + +/* * enable/disable the multi-driver; This is only valid for output and * allows the output pin to run as an open collector output. */ @@ -242,6 +350,41 @@ int __init_or_module at91_set_multi_drive(unsigned pin, int is_on) EXPORT_SYMBOL(at91_set_multi_drive); /* + * enable/disable the pull-down. + * If pull-up already enabled while calling the function, we disable it. + */ +int __init_or_module at91_set_pulldown(unsigned pin, int is_on) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio || !has_pio3()) + return -EINVAL; + + /* Disable pull-up anyway */ + __raw_writel(mask, pio + PIO_PUDR); + __raw_writel(mask, pio + (is_on ? PIO_PPDER : PIO_PPDDR)); + return 0; +} +EXPORT_SYMBOL(at91_set_pulldown); + +/* + * disable Schmitt trigger + */ +int __init_or_module at91_disable_schmitt_trig(unsigned pin) +{ + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); + + if (!pio || !has_pio3()) + return -EINVAL; + + __raw_writel(__raw_readl(pio + PIO_SCHMITT) | mask, pio + PIO_SCHMITT); + return 0; +} +EXPORT_SYMBOL(at91_disable_schmitt_trig); + +/* * assuming the pin is muxed as a gpio output, set its value. */ int at91_set_gpio_value(unsigned pin, int value) @@ -347,7 +490,10 @@ void at91_gpio_resume(void) * To use any AT91_PIN_* as an externally triggered IRQ, first call * at91_set_gpio_input() then maybe enable its glitch filter. * Then just request_irq() with the pin ID; it works like any ARM IRQ - * handler, though it always triggers on rising and falling edges. + * handler. + * First implementation always triggers on rising and falling edges + * whereas the newer PIO3 can be additionally configured to trigger on + * level, edge with any polarity. * * Alternatively, certain pins may be used directly as IRQ0..IRQ6 after * configuring them with at91_set_a_periph() or at91_set_b_periph(). @@ -385,12 +531,55 @@ static int gpio_irq_type(struct irq_data *d, unsigned type) } } +/* Alternate irq type for PIO3 support */ +static int alt_gpio_irq_type(struct irq_data *d, unsigned type) +{ + struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(d); + void __iomem *pio = at91_gpio->regbase; + unsigned mask = 1 << d->hwirq; + + switch (type) { + case IRQ_TYPE_EDGE_RISING: + __raw_writel(mask, pio + PIO_ESR); + __raw_writel(mask, pio + PIO_REHLSR); + break; + case IRQ_TYPE_EDGE_FALLING: + __raw_writel(mask, pio + PIO_ESR); + __raw_writel(mask, pio + PIO_FELLSR); + break; + case IRQ_TYPE_LEVEL_LOW: + __raw_writel(mask, pio + PIO_LSR); + __raw_writel(mask, pio + PIO_FELLSR); + break; + case IRQ_TYPE_LEVEL_HIGH: + __raw_writel(mask, pio + PIO_LSR); + __raw_writel(mask, pio + PIO_REHLSR); + break; + case IRQ_TYPE_EDGE_BOTH: + /* + * disable additional interrupt modes: + * fall back to default behavior + */ + __raw_writel(mask, pio + PIO_AIMDR); + return 0; + case IRQ_TYPE_NONE: + default: + pr_warn("AT91: No type for irq %d\n", gpio_to_irq(d->irq)); + return -EINVAL; + } + + /* enable additional interrupt modes */ + __raw_writel(mask, pio + PIO_AIMER); + + return 0; +} + static struct irq_chip gpio_irqchip = { .name = "GPIO", .irq_disable = gpio_irq_mask, .irq_mask = gpio_irq_mask, .irq_unmask = gpio_irq_unmask, - .irq_set_type = gpio_irq_type, + /* .irq_set_type is set dynamically */ .irq_set_wake = gpio_irq_set_wake, }; @@ -433,6 +622,33 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc) #ifdef CONFIG_DEBUG_FS +static void gpio_printf(struct seq_file *s, void __iomem *pio, unsigned mask) +{ + char *trigger = NULL; + char *polarity = NULL; + + if (__raw_readl(pio + PIO_IMR) & mask) { + if (!has_pio3() || !(__raw_readl(pio + PIO_AIMMR) & mask )) { + trigger = "edge"; + polarity = "both"; + } else { + if (__raw_readl(pio + PIO_ELSR) & mask) { + trigger = "level"; + polarity = __raw_readl(pio + PIO_FRLHSR) & mask ? + "high" : "low"; + } else { + trigger = "edge"; + polarity = __raw_readl(pio + PIO_FRLHSR) & mask ? + "rising" : "falling"; + } + } + seq_printf(s, "IRQ:%s-%s\t", trigger, polarity); + } else { + seq_printf(s, "GPIO:%s\t\t", + __raw_readl(pio + PIO_PDSR) & mask ? "1" : "0"); + } +} + static int at91_gpio_show(struct seq_file *s, void *unused) { int bank, j; @@ -440,7 +656,7 @@ static int at91_gpio_show(struct seq_file *s, void *unused) /* print heading */ seq_printf(s, "Pin\t"); for (bank = 0; bank < gpio_banks; bank++) { - seq_printf(s, "PIO%c\t", 'A' + bank); + seq_printf(s, "PIO%c\t\t", 'A' + bank); }; seq_printf(s, "\n\n"); @@ -454,11 +670,10 @@ static int at91_gpio_show(struct seq_file *s, void *unused) unsigned mask = pin_to_mask(pin); if (__raw_readl(pio + PIO_PSR) & mask) - seq_printf(s, "GPIO:%s", __raw_readl(pio + PIO_PDSR) & mask ? "1" : "0"); + gpio_printf(s, pio, mask); else - seq_printf(s, "%s", __raw_readl(pio + PIO_ABSR) & mask ? "B" : "A"); - - seq_printf(s, "\t"); + seq_printf(s, "%c\t\t", + peripheral_function(pio, mask)); } seq_printf(s, "\n"); @@ -529,6 +744,12 @@ int __init at91_gpio_of_irq_setup(struct device_node *node, int alias_idx = of_alias_get_id(node, "gpio"); struct at91_gpio_chip *at91_gpio = &gpio_chip[alias_idx]; + /* Setup proper .irq_set_type function */ + if (has_pio3()) + gpio_irqchip.irq_set_type = alt_gpio_irq_type; + else + gpio_irqchip.irq_set_type = gpio_irq_type; + /* Disable irqs of this PIO controller */ __raw_writel(~0, at91_gpio->regbase + PIO_IDR); @@ -593,6 +814,12 @@ void __init at91_gpio_irq_setup(void) int gpio_irqnbr = 0; struct at91_gpio_chip *this, *prev; + /* Setup proper .irq_set_type function */ + if (has_pio3()) + gpio_irqchip.irq_set_type = alt_gpio_irq_type; + else + gpio_irqchip.irq_set_type = gpio_irq_type; + for (pioc = 0, this = gpio_chip, prev = NULL; pioc++ < gpio_banks; prev = this, this++) { @@ -696,9 +923,8 @@ static void at91_gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip) at91_get_gpio_value(pin) ? "set" : "clear"); else - seq_printf(s, "[periph %s]\n", - __raw_readl(pio + PIO_ABSR) & - mask ? "B" : "A"); + seq_printf(s, "[periph %c]\n", + peripheral_function(pio, mask)); } } } @@ -781,6 +1007,10 @@ static void __init of_at91_gpio_init_one(struct device_node *np) goto ioremap_err; } + /* Get capabilities from compatibility property */ + if (of_device_is_compatible(np, "atmel,at91sam9x5-gpio")) + at91_gpio_caps |= AT91_GPIO_CAP_PIO3; + /* Setup clock */ if (at91_gpio_setup_clk(alias_idx)) goto ioremap_err; diff --git a/arch/arm/mach-at91/include/mach/at91_pio.h b/arch/arm/mach-at91/include/mach/at91_pio.h index c6a31bf..732b11c 100644 --- a/arch/arm/mach-at91/include/mach/at91_pio.h +++ b/arch/arm/mach-at91/include/mach/at91_pio.h @@ -40,10 +40,35 @@ #define PIO_PUER 0x64 /* Pull-up Enable Register */ #define PIO_PUSR 0x68 /* Pull-up Status Register */ #define PIO_ASR 0x70 /* Peripheral A Select Register */ +#define PIO_ABCDSR1 0x70 /* Peripheral ABCD Select Register 1 [some sam9 only] */ #define PIO_BSR 0x74 /* Peripheral B Select Register */ +#define PIO_ABCDSR2 0x74 /* Peripheral ABCD Select Register 2 [some sam9 only] */ #define PIO_ABSR 0x78 /* AB Status Register */ +#define PIO_IFSCDR 0x80 /* Input Filter Slow Clock Disable Register */ +#define PIO_IFSCER 0x84 /* Input Filter Slow Clock Enable Register */ +#define PIO_IFSCSR 0x88 /* Input Filter Slow Clock Status Register */ +#define PIO_SCDR 0x8c /* Slow Clock Divider Debouncing Register */ +#define PIO_SCDR_DIV (0x3fff << 0) /* Slow Clock Divider Mask */ +#define PIO_PPDDR 0x90 /* Pad Pull-down Disable Register */ +#define PIO_PPDER 0x94 /* Pad Pull-down Enable Register */ +#define PIO_PPDSR 0x98 /* Pad Pull-down Status Register */ #define PIO_OWER 0xa0 /* Output Write Enable Register */ #define PIO_OWDR 0xa4 /* Output Write Disable Register */ #define PIO_OWSR 0xa8 /* Output Write Status Register */ +#define PIO_AIMER 0xb0 /* Additional Interrupt Modes Enable Register */ +#define PIO_AIMDR 0xb4 /* Additional Interrupt Modes Disable Register */ +#define PIO_AIMMR 0xb8 /* Additional Interrupt Modes Mask Register */ +#define PIO_ESR 0xc0 /* Edge Select Register */ +#define PIO_LSR 0xc4 /* Level Select Register */ +#define PIO_ELSR 0xc8 /* Edge/Level Status Register */ +#define PIO_FELLSR 0xd0 /* Falling Edge/Low Level Select Register */ +#define PIO_REHLSR 0xd4 /* Rising Edge/ High Level Select Register */ +#define PIO_FRLHSR 0xd8 /* Fall/Rise - Low/High Status Register */ +#define PIO_SCHMITT 0x100 /* Schmitt Trigger Register */ + +#define ABCDSR_PERIPH_A 0x0 +#define ABCDSR_PERIPH_B 0x1 +#define ABCDSR_PERIPH_C 0x2 +#define ABCDSR_PERIPH_D 0x3 #endif diff --git a/arch/arm/mach-at91/include/mach/gpio.h b/arch/arm/mach-at91/include/mach/gpio.h index 7cf009b..eed465a 100644 --- a/arch/arm/mach-at91/include/mach/gpio.h +++ b/arch/arm/mach-at91/include/mach/gpio.h @@ -191,10 +191,15 @@ extern int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup); extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup); extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_C_periph(unsigned pin, int use_pullup); +extern int __init_or_module at91_set_D_periph(unsigned pin, int use_pullup); extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup); extern int __init_or_module at91_set_gpio_output(unsigned pin, int value); extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on); +extern int __init_or_module at91_set_debounce(unsigned pin, int is_on, int div); extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on); +extern int __init_or_module at91_set_pulldown(unsigned pin, int is_on); +extern int __init_or_module at91_disable_schmitt_trig(unsigned pin); /* callable at any time */ extern int at91_set_gpio_value(unsigned pin, int value); -- cgit v0.10.2