From 593702c71a415b153bd81fbc487394979f3e7a63 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Thu, 8 Sep 2011 15:09:34 +0800 Subject: i2c-imx: remove init/exit hooks from platform data The init/exit hooks in platform data are being used nowhere, so can be removed. Signed-off-by: Shawn Guo Cc: Darius Augulis Cc: Ben Dooks Acked-by: Grant Likely Acked-by: Sascha Hauer Signed-off-by: Ben Dooks diff --git a/arch/arm/plat-mxc/include/mach/i2c.h b/arch/arm/plat-mxc/include/mach/i2c.h index 4a5dc5c..375cdd0 100644 --- a/arch/arm/plat-mxc/include/mach/i2c.h +++ b/arch/arm/plat-mxc/include/mach/i2c.h @@ -11,14 +11,10 @@ /** * struct imxi2c_platform_data - structure of platform data for MXC I2C driver - * @init: Initialise gpio's and other board specific things - * @exit: Free everything initialised by @init * @bitrate: Bus speed measured in Hz * **/ struct imxi2c_platform_data { - int (*init)(struct device *dev); - void (*exit)(struct device *dev); int bitrate; }; diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c index 4c2a62b..54d809e 100644 --- a/drivers/i2c/busses/i2c-imx.c +++ b/drivers/i2c/busses/i2c-imx.c @@ -466,7 +466,7 @@ static int __init i2c_imx_probe(struct platform_device *pdev) { struct imx_i2c_struct *i2c_imx; struct resource *res; - struct imxi2c_platform_data *pdata; + struct imxi2c_platform_data *pdata = pdev->dev.platform_data; void __iomem *base; resource_size_t res_size; int irq; @@ -485,19 +485,11 @@ static int __init i2c_imx_probe(struct platform_device *pdev) return -ENOENT; } - pdata = pdev->dev.platform_data; - - if (pdata && pdata->init) { - ret = pdata->init(&pdev->dev); - if (ret) - return ret; - } - res_size = resource_size(res); if (!request_mem_region(res->start, res_size, DRIVER_NAME)) { - ret = -EBUSY; - goto fail0; + dev_err(&pdev->dev, "request_mem_region failed\n"); + return -EBUSY; } base = ioremap(res->start, res_size); @@ -586,9 +578,6 @@ fail2: iounmap(base); fail1: release_mem_region(res->start, resource_size(res)); -fail0: - if (pdata && pdata->exit) - pdata->exit(&pdev->dev); return ret; /* Return error number */ } @@ -611,10 +600,6 @@ static int __exit i2c_imx_remove(struct platform_device *pdev) writeb(0, i2c_imx->base + IMX_I2C_I2CR); writeb(0, i2c_imx->base + IMX_I2C_I2SR); - /* Shut down hardware */ - if (pdata && pdata->exit) - pdata->exit(&pdev->dev); - clk_put(i2c_imx->clk); iounmap(i2c_imx->base); -- cgit v0.10.2 From dfcd04b19d16c0016c705ed96a8b3cfa5315a2e9 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Thu, 8 Sep 2011 15:09:35 +0800 Subject: i2c-imx: add device tree probe support It adds device tree probe support for i2c-imx driver. Signed-off-by: Shawn Guo Cc: Grant Likely Cc: Darius Augulis Cc: Ben Dooks Acked-by: Grant Likely Signed-off-by: Ben Dooks diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt new file mode 100644 index 0000000..f3cf43b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt @@ -0,0 +1,25 @@ +* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX + +Required properties: +- compatible : Should be "fsl,-i2c" +- reg : Should contain I2C/HS-I2C registers location and length +- interrupts : Should contain I2C/HS-I2C interrupt + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the propoerty indicates the default frequency 100 kHz. + +Examples: + +i2c@83fc4000 { /* I2C2 on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x83fc4000 0x4000>; + interrupts = <63>; +}; + +i2c@70038000 { /* HS-I2C on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + reg = <0x70038000 0x4000>; + interrupts = <64>; + clock-frequency = <400000>; +}; diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c index 54d809e..58832e5 100644 --- a/drivers/i2c/busses/i2c-imx.c +++ b/drivers/i2c/busses/i2c-imx.c @@ -48,6 +48,9 @@ #include #include #include +#include +#include +#include #include #include @@ -125,6 +128,11 @@ struct imx_i2c_struct { unsigned int ifdr; /* IMX_I2C_IFDR */ }; +static const struct of_device_id i2c_imx_dt_ids[] = { + { .compatible = "fsl,imx1-i2c", }, + { /* sentinel */ } +}; + /** Functions for IMX I2C adapter driver *************************************** *******************************************************************************/ @@ -469,7 +477,7 @@ static int __init i2c_imx_probe(struct platform_device *pdev) struct imxi2c_platform_data *pdata = pdev->dev.platform_data; void __iomem *base; resource_size_t res_size; - int irq; + int irq, bitrate; int ret; dev_dbg(&pdev->dev, "<%s>\n", __func__); @@ -512,6 +520,7 @@ static int __init i2c_imx_probe(struct platform_device *pdev) i2c_imx->adapter.algo = &i2c_imx_algo; i2c_imx->adapter.dev.parent = &pdev->dev; i2c_imx->adapter.nr = pdev->id; + i2c_imx->adapter.dev.of_node = pdev->dev.of_node; i2c_imx->irq = irq; i2c_imx->base = base; i2c_imx->res = res; @@ -538,10 +547,12 @@ static int __init i2c_imx_probe(struct platform_device *pdev) i2c_set_adapdata(&i2c_imx->adapter, i2c_imx); /* Set up clock divider */ - if (pdata && pdata->bitrate) - i2c_imx_set_clk(i2c_imx, pdata->bitrate); - else - i2c_imx_set_clk(i2c_imx, IMX_I2C_BIT_RATE); + bitrate = IMX_I2C_BIT_RATE; + ret = of_property_read_u32(pdev->dev.of_node, + "clock-frequency", &bitrate); + if (ret < 0 && pdata && pdata->bitrate) + bitrate = pdata->bitrate; + i2c_imx_set_clk(i2c_imx, bitrate); /* Set up chip registers to defaults */ writeb(0, i2c_imx->base + IMX_I2C_I2CR); @@ -554,6 +565,8 @@ static int __init i2c_imx_probe(struct platform_device *pdev) goto fail5; } + of_i2c_register_devices(&i2c_imx->adapter); + /* Set up platform driver data */ platform_set_drvdata(pdev, i2c_imx); @@ -584,7 +597,6 @@ fail1: static int __exit i2c_imx_remove(struct platform_device *pdev) { struct imx_i2c_struct *i2c_imx = platform_get_drvdata(pdev); - struct imxi2c_platform_data *pdata = pdev->dev.platform_data; /* remove adapter */ dev_dbg(&i2c_imx->adapter.dev, "adapter removed\n"); @@ -613,6 +625,7 @@ static struct platform_driver i2c_imx_driver = { .driver = { .name = DRIVER_NAME, .owner = THIS_MODULE, + .of_match_table = i2c_imx_dt_ids, } }; -- cgit v0.10.2 From b88530884141e977b3702d8e82de52e553b45876 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:04 -0700 Subject: I2C: OMAP2+: Name registers in I2C IP V2 only accordingly The OMAP I2C driver dynamically chooses between two register sets of differing sizes depending on the cpu type it finds itself on. It has been observed that the existing code references non-existing registers on OMAP3530, because while it correctly chose the smaller register layout based on cpu type, the code uses the probed register ID to decide if to execute code referencing an extra register, and both register layout devices on OMAP3530 and OMAP4430 report the same probed ID of 0x40. This patch changes the extended register names only found on IP V2 of the I2C peripheral unit accordingly to help show up errors in usage. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 2dfb631..d40943c 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -72,11 +72,12 @@ enum { OMAP_I2C_SCLH_REG, OMAP_I2C_SYSTEST_REG, OMAP_I2C_BUFSTAT_REG, - OMAP_I2C_REVNB_LO, - OMAP_I2C_REVNB_HI, - OMAP_I2C_IRQSTATUS_RAW, - OMAP_I2C_IRQENABLE_SET, - OMAP_I2C_IRQENABLE_CLR, + /* only on OMAP4430 */ + OMAP_I2C_IP_V2_REVNB_LO, + OMAP_I2C_IP_V2_REVNB_HI, + OMAP_I2C_IP_V2_IRQSTATUS_RAW, + OMAP_I2C_IP_V2_IRQENABLE_SET, + OMAP_I2C_IP_V2_IRQENABLE_CLR, }; /* I2C Interrupt Enable Register (OMAP_I2C_IE): */ @@ -244,11 +245,11 @@ static const u8 omap4_reg_map[] = { [OMAP_I2C_SCLH_REG] = 0xb8, [OMAP_I2C_SYSTEST_REG] = 0xbC, [OMAP_I2C_BUFSTAT_REG] = 0xc0, - [OMAP_I2C_REVNB_LO] = 0x00, - [OMAP_I2C_REVNB_HI] = 0x04, - [OMAP_I2C_IRQSTATUS_RAW] = 0x24, - [OMAP_I2C_IRQENABLE_SET] = 0x2c, - [OMAP_I2C_IRQENABLE_CLR] = 0x30, + [OMAP_I2C_IP_V2_REVNB_LO] = 0x00, + [OMAP_I2C_IP_V2_REVNB_HI] = 0x04, + [OMAP_I2C_IP_V2_IRQSTATUS_RAW] = 0x24, + [OMAP_I2C_IP_V2_IRQENABLE_SET] = 0x2c, + [OMAP_I2C_IP_V2_IRQENABLE_CLR] = 0x30, }; static inline void omap_i2c_write_reg(struct omap_i2c_dev *i2c_dev, @@ -309,7 +310,7 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev) dev->iestate = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG); if (dev->rev >= OMAP_I2C_REV_ON_4430) - omap_i2c_write_reg(dev, OMAP_I2C_IRQENABLE_CLR, 1); + omap_i2c_write_reg(dev, OMAP_I2C_IP_V2_IRQENABLE_CLR, 1); else omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, 0); -- cgit v0.10.2 From 5c825ee202d0891269e29197d5b21f8e2be3498a Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:05 -0700 Subject: I2C: OMAP: add rev to omap i2c platform data We need to pass the I2C IP revision from the hwmod class up into the OMAP I2C driver, which does not have direct access to it. This adds a member to the platform data the OMAP I2C driver does use already to hold the I2C IP revision. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/include/linux/i2c-omap.h b/include/linux/i2c-omap.h index 0aa0cbd..55eac25 100644 --- a/include/linux/i2c-omap.h +++ b/include/linux/i2c-omap.h @@ -32,6 +32,7 @@ struct omap_i2c_bus_platform_data { u32 clkrate; + u32 rev; void (*set_mpu_wkup_lat)(struct device *dev, long set); int (*device_enable) (struct platform_device *pdev); int (*device_shutdown) (struct platform_device *pdev); -- cgit v0.10.2 From 67b90c67205149173dc0cfdc46039be92fa390b6 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:06 -0700 Subject: I2C: OMAP1: set IP revision in platform data All OMAP1 are using "IP revision 1" in terms of register layout. We set this information in omap1_i2c_add_bus() so we don't have to use cpu_is_xxx() any more in the omap i2c driver. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/arch/arm/plat-omap/i2c.c b/arch/arm/plat-omap/i2c.c index 3341ca4..a938df0 100644 --- a/arch/arm/plat-omap/i2c.c +++ b/arch/arm/plat-omap/i2c.c @@ -108,6 +108,9 @@ static inline int omap1_i2c_add_bus(int bus_id) res[1].start = INT_I2C; pdata = &i2c_pdata[bus_id - 1]; + /* all OMAP1 have IP version 1 register set */ + pdata->rev = OMAP_I2C_IP_VERSION_1; + return platform_device_register(pdev); } -- cgit v0.10.2 From d177e5ddb83a4bc518270e705e60ccc5a5aa6410 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:06 -0700 Subject: I2C: OMAP2+: Pass hwmod rev knowledge via platform_data when i2c bus added Mark each OMAP I2C bus with the hwmod's knowledge of which I2C IP version is in the chip we're running on. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/arch/arm/plat-omap/i2c.c b/arch/arm/plat-omap/i2c.c index a938df0..0d3eda7 100644 --- a/arch/arm/plat-omap/i2c.c +++ b/arch/arm/plat-omap/i2c.c @@ -155,6 +155,12 @@ static inline int omap2_i2c_add_bus(int bus_id) pdata = &i2c_pdata[bus_id - 1]; /* + * pass the hwmod class's CPU-specific knowledge of I2C IP revision in + * use up to the OMAP I2C driver via platform data + */ + pdata->rev = oh->class->rev; + + /* * When waiting for completion of a i2c transfer, we need to * set a wake up latency constraint for the MPU. This is to * ensure quick enough wakeup from idle, when transfer -- cgit v0.10.2 From a1295577773d9756b65972be7b462e4382996d08 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:06 -0700 Subject: I2C: OMAP2+: use platform_data ip revision to select register map Change the register map names to reflect the IP revision they are representing, and use the platform_data IP revision index to select between them at init time. Eliminates 1 of 17 cpu_...() calls in the driver. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index d40943c..9172a57 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -205,7 +205,7 @@ struct omap_i2c_dev { u16 errata; }; -static const u8 reg_map[] = { +static const u8 reg_map_ip_v1[] = { [OMAP_I2C_REV_REG] = 0x00, [OMAP_I2C_IE_REG] = 0x01, [OMAP_I2C_STAT_REG] = 0x02, @@ -226,7 +226,7 @@ static const u8 reg_map[] = { [OMAP_I2C_BUFSTAT_REG] = 0x10, }; -static const u8 omap4_reg_map[] = { +static const u8 reg_map_ip_v2[] = { [OMAP_I2C_REV_REG] = 0x04, [OMAP_I2C_IE_REG] = 0x2c, [OMAP_I2C_STAT_REG] = 0x28, @@ -1035,10 +1035,10 @@ omap_i2c_probe(struct platform_device *pdev) else dev->reg_shift = 2; - if (cpu_is_omap44xx()) - dev->regs = (u8 *) omap4_reg_map; + if (pdata->rev == OMAP_I2C_IP_VERSION_2) + dev->regs = (u8 *)reg_map_ip_v2; else - dev->regs = (u8 *) reg_map; + dev->regs = (u8 *)reg_map_ip_v1; pm_runtime_enable(&pdev->dev); omap_i2c_unidle(dev); -- cgit v0.10.2 From 6314f09e9517ed3d7d951525a111df858a6dd1a4 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:07 -0700 Subject: I2C: OMAP2+: Solve array bounds overflow error on i2c idle This solves the main problem the patch series is about. Prior to this patch on OMAP3530 the driver wrongly interprets the I2C peripheral unit's own reported revision as meaning it is running on an IP V2 device and must use the extended registers. In fact OMAP3530 is IP V1 with the smaller register set, the reason for the confusion is that the hardware does in fact report having the same IP revision index as is found on an OMAP4430, which really is IP V2 and has the extended registers. This corrects the test for which registers to use so that it decides using hwmod knowledge found in the platform_data. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 9172a57..e6792ab 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -309,7 +309,7 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev) pdata = pdev->dev.platform_data; dev->iestate = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG); - if (dev->rev >= OMAP_I2C_REV_ON_4430) + if (pdata->rev == OMAP_I2C_IP_VERSION_2) omap_i2c_write_reg(dev, OMAP_I2C_IP_V2_IRQENABLE_CLR, 1); else omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, 0); -- cgit v0.10.2 From 4e80f727bf59e8c1ea8e47c45c9ef368d353d835 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:07 -0700 Subject: I2C: OMAP2+: address confused probed version naming The driver reflects the confusion that probed I2C revision from the hardware of 0x40 means it is on an OMAP4430. However, you will probe the same 0x40 ID on an OMAP3530. So this patch changes the name to reflect that. It also clarifies that the original name OMAP_I2C_REV_2 is referring to some ancient OMAP1 revision number, not to be confused with the IP revisions this patch series introduces. Similarly the term "rev" is used in the ancient OMAP1 ISR, the term is changed to use omap1 instead. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index e6792ab..0254da4 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -42,12 +42,12 @@ #include /* I2C controller revisions */ -#define OMAP_I2C_REV_2 0x20 +#define OMAP_I2C_OMAP1_REV_2 0x20 /* I2C controller revisions present on specific hardware */ #define OMAP_I2C_REV_ON_2430 0x36 #define OMAP_I2C_REV_ON_3430 0x3C -#define OMAP_I2C_REV_ON_4430 0x40 +#define OMAP_I2C_REV_ON_3530_4430 0x40 /* timeout waiting for the controller to respond */ #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000)) @@ -314,7 +314,7 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev) else omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, 0); - if (dev->rev < OMAP_I2C_REV_2) { + if (dev->rev < OMAP_I2C_OMAP1_REV_2) { iv = omap_i2c_read_reg(dev, OMAP_I2C_IV_REG); /* Read clears */ } else { omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, dev->iestate); @@ -336,7 +336,7 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) unsigned long internal_clk = 0; struct clk *fclk; - if (dev->rev >= OMAP_I2C_REV_2) { + if (dev->rev >= OMAP_I2C_OMAP1_REV_2) { /* Disable I2C controller before soft reset */ omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, omap_i2c_read_reg(dev, OMAP_I2C_CON_REG) & @@ -379,7 +379,9 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) * REVISIT: Some wkup sources might not be needed. */ dev->westate = OMAP_I2C_WE_ALL; - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate); + if (dev->rev < OMAP_I2C_REV_ON_3530_4430) + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, + dev->westate); } } omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); @@ -721,7 +723,7 @@ static inline void i2c_omap_errata_i207(struct omap_i2c_dev *dev, u16 stat) #ifdef CONFIG_ARCH_OMAP15XX static irqreturn_t -omap_i2c_rev1_isr(int this_irq, void *dev_id) +omap_i2c_omap1_isr(int this_irq, void *dev_id) { struct omap_i2c_dev *dev = dev_id; u16 iv, w; @@ -775,7 +777,7 @@ omap_i2c_rev1_isr(int this_irq, void *dev_id) return IRQ_HANDLED; } #else -#define omap_i2c_rev1_isr NULL +#define omap_i2c_omap1_isr NULL #endif /* @@ -1060,7 +1062,7 @@ omap_i2c_probe(struct platform_device *pdev) * size. This is to ensure that we can handle the status on int * call back latencies. */ - if (dev->rev >= OMAP_I2C_REV_ON_4430) { + if (dev->rev >= OMAP_I2C_REV_ON_3530_4430) { dev->fifo_size = 0; dev->b_hw = 0; /* Disable hardware fixes */ } else { @@ -1076,7 +1078,8 @@ omap_i2c_probe(struct platform_device *pdev) /* reset ASAP, clearing any IRQs */ omap_i2c_init(dev); - isr = (dev->rev < OMAP_I2C_REV_2) ? omap_i2c_rev1_isr : omap_i2c_isr; + isr = (dev->rev < OMAP_I2C_OMAP1_REV_2) ? omap_i2c_omap1_isr : + omap_i2c_isr; r = request_irq(dev->irq, isr, 0, pdev->name, dev); if (r) { -- cgit v0.10.2 From c23600a688dc71f4312f83cb0f23a736e1578a5e Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:08 -0700 Subject: I2C: OMAP1/OMAP2+: add flags field to omap i2c platform data OMAP I2C driver can access the configuration flags through its platform data. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/include/linux/i2c-omap.h b/include/linux/i2c-omap.h index 55eac25..56a9924 100644 --- a/include/linux/i2c-omap.h +++ b/include/linux/i2c-omap.h @@ -33,6 +33,7 @@ struct omap_i2c_bus_platform_data { u32 clkrate; u32 rev; + u32 flags; void (*set_mpu_wkup_lat)(struct device *dev, long set); int (*device_enable) (struct platform_device *pdev); int (*device_shutdown) (struct platform_device *pdev); -- cgit v0.10.2 From 029a1e73cd702e41ebfc07e11555592e0bb1693c Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:08 -0700 Subject: I2C: OMAP2+: Pass flags up to omap i2c platform_data as well This is how the driver can find the flags for its implementation functionality in its platform_data Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/arch/arm/plat-omap/i2c.c b/arch/arm/plat-omap/i2c.c index 0d3eda7..9098669 100644 --- a/arch/arm/plat-omap/i2c.c +++ b/arch/arm/plat-omap/i2c.c @@ -141,6 +141,7 @@ static inline int omap2_i2c_add_bus(int bus_id) struct omap_device *od; char oh_name[MAX_OMAP_I2C_HWMOD_NAME_LEN]; struct omap_i2c_bus_platform_data *pdata; + struct omap_i2c_dev_attr *dev_attr; omap2_i2c_mux_pins(bus_id); @@ -156,10 +157,14 @@ static inline int omap2_i2c_add_bus(int bus_id) pdata = &i2c_pdata[bus_id - 1]; /* * pass the hwmod class's CPU-specific knowledge of I2C IP revision in - * use up to the OMAP I2C driver via platform data + * use, and functionality implementation flags, up to the OMAP I2C + * driver via platform data */ pdata->rev = oh->class->rev; + dev_attr = (struct omap_i2c_dev_attr *)oh->dev_attr; + pdata->flags = dev_attr->flags; + /* * When waiting for completion of a i2c transfer, we need to * set a wake up latency constraint for the MPU. This is to -- cgit v0.10.2 From 8e286f5a2156f71dd304ce9ad1cd6b07231aaae6 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:09 -0700 Subject: I2C: OMAP1: set i2c unit feature implementation flags in platform data Most of the OMAP1 implementation flags are set statically, with the exception that omap7xx has its data bus wired up differently. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/arch/arm/plat-omap/i2c.c b/arch/arm/plat-omap/i2c.c index 9098669..2388b8e 100644 --- a/arch/arm/plat-omap/i2c.c +++ b/arch/arm/plat-omap/i2c.c @@ -111,6 +111,19 @@ static inline int omap1_i2c_add_bus(int bus_id) /* all OMAP1 have IP version 1 register set */ pdata->rev = OMAP_I2C_IP_VERSION_1; + /* all OMAP1 I2C are implemented like this */ + pdata->flags = OMAP_I2C_FLAG_NO_FIFO | + OMAP_I2C_FLAG_SIMPLE_CLOCK | + OMAP_I2C_FLAG_16BIT_DATA_REG | + OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK; + + /* how the cpu bus is wired up differs for 7xx only */ + + if (cpu_is_omap7xx()) + pdata->flags |= OMAP_I2C_FLAG_BUS_SHIFT_1; + else + pdata->flags |= OMAP_I2C_FLAG_BUS_SHIFT_2; + return platform_device_register(pdev); } -- cgit v0.10.2 From 3be0053ee1a8bfb68de82716ae784f75e1610d60 Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:09 -0700 Subject: I2C: OMAP2+: Convert omap I2C driver to use feature implementation flags from platform data This patch eliminates all cpu_...() tests from the OMAP I2C driver. Instead, it uses the functionality flags in the platform data to make the decisions about product variations the driver needs to handle. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 0254da4..3aaf7f1 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -277,7 +277,7 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev) pm_runtime_get_sync(&pdev->dev); - if (cpu_is_omap34xx()) { + if (pdata->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate); omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, dev->scllstate); @@ -335,6 +335,11 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) unsigned long timeout; unsigned long internal_clk = 0; struct clk *fclk; + struct platform_device *pdev; + struct omap_i2c_bus_platform_data *pdata; + + pdev = to_platform_device(dev->dev); + pdata = pdev->dev.platform_data; if (dev->rev >= OMAP_I2C_OMAP1_REV_2) { /* Disable I2C controller before soft reset */ @@ -386,7 +391,7 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) } omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); - if (cpu_class_is_omap1()) { + if (pdata->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) { /* * The I2C functional clock is the armxor_ck, so there's * no need to get "armxor_ck" separately. Now, if OMAP2420 @@ -410,7 +415,7 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) psc = fclk_rate / 12000000; } - if (!(cpu_class_is_omap1() || cpu_is_omap2420())) { + if (!(pdata->flags & OMAP_I2C_FLAG_SIMPLE_CLOCK)) { /* * HSI2C controller internal clk rate should be 19.2 Mhz for @@ -418,7 +423,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) * to get longer filter period for better noise suppression. * The filter is iclk (fclk for HS) period. */ - if (dev->speed > 400 || cpu_is_omap2430()) + if (dev->speed > 400 || + pdata->flags & OMAP_I2C_FLAG_FORCE_19200_INT_CLK) internal_clk = 19200; else if (dev->speed > 100) internal_clk = 9600; @@ -487,7 +493,7 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) dev->errata = 0; - if (cpu_is_omap2430() || cpu_is_omap34xx()) + if (pdata->flags & OMAP_I2C_FLAG_APPLY_ERRATA_I207) dev->errata |= I2C_OMAP_ERRATA_I207; /* Enable interrupts */ @@ -496,7 +502,7 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) OMAP_I2C_IE_AL) | ((dev->fifo_size) ? (OMAP_I2C_IE_RDR | OMAP_I2C_IE_XDR) : 0); omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate); - if (cpu_is_omap34xx()) { + if (pdata->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { dev->pscstate = psc; dev->scllstate = scll; dev->sclhstate = sclh; @@ -816,6 +822,11 @@ omap_i2c_isr(int this_irq, void *dev_id) u16 bits; u16 stat, w; int err, count = 0; + struct platform_device *pdev; + struct omap_i2c_bus_platform_data *pdata; + + pdev = to_platform_device(dev->dev); + pdata = pdev->dev.platform_data; if (dev->idle) return IRQ_NONE; @@ -884,8 +895,8 @@ complete: * Data reg in 2430, omap3 and * omap4 is 8 bit wide */ - if (cpu_class_is_omap1() || - cpu_is_omap2420()) { + if (pdata->flags & + OMAP_I2C_FLAG_16BIT_DATA_REG) { if (dev->buf_len) { *dev->buf++ = w >> 8; dev->buf_len--; @@ -927,8 +938,8 @@ complete: * Data reg in 2430, omap3 and * omap4 is 8 bit wide */ - if (cpu_class_is_omap1() || - cpu_is_omap2420()) { + if (pdata->flags & + OMAP_I2C_FLAG_16BIT_DATA_REG) { if (dev->buf_len) { w |= *dev->buf++ << 8; dev->buf_len--; @@ -1030,12 +1041,7 @@ omap_i2c_probe(struct platform_device *pdev) platform_set_drvdata(pdev, dev); - if (cpu_is_omap7xx()) - dev->reg_shift = 1; - else if (cpu_is_omap44xx()) - dev->reg_shift = 0; - else - dev->reg_shift = 2; + dev->reg_shift = (pdata->flags >> OMAP_I2C_FLAG_BUS_SHIFT__SHIFT) & 3; if (pdata->rev == OMAP_I2C_IP_VERSION_2) dev->regs = (u8 *)reg_map_ip_v2; @@ -1050,7 +1056,7 @@ omap_i2c_probe(struct platform_device *pdev) if (dev->rev <= OMAP_I2C_REV_ON_3430) dev->errata |= I2C_OMAP3_1P153; - if (!(cpu_class_is_omap1() || cpu_is_omap2420())) { + if (!(pdata->flags & OMAP_I2C_FLAG_NO_FIFO)) { u16 s; /* Set up the fifo size - Get total size */ -- cgit v0.10.2 From 9550d4d7ab9aff125d3f7d48d3e97c093d19bdbe Mon Sep 17 00:00:00 2001 From: Andy Green Date: Mon, 30 May 2011 07:43:10 -0700 Subject: I2C: OMAP1/OMAP2+: prepend I2C IP version to probed version shown in dev_info The IP version is prepended to the existing printed probed version as an "epoch" version. Cc: patches@linaro.org Reported-by: Peter Maydell Signed-off-by: Andy Green Signed-off-by: Tony Lindgren Acked-by: Ben Dooks Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 3aaf7f1..642a233 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -1093,8 +1093,8 @@ omap_i2c_probe(struct platform_device *pdev) goto err_unuse_clocks; } - dev_info(dev->dev, "bus %d rev%d.%d at %d kHz\n", - pdev->id, dev->rev >> 4, dev->rev & 0xf, dev->speed); + dev_info(dev->dev, "bus %d rev%d.%d.%d at %d kHz\n", pdev->id, + pdata->rev, dev->rev >> 4, dev->rev & 0xf, dev->speed); omap_i2c_idle(dev); -- cgit v0.10.2 From cb28e5823588cc357865cc0eab2afeec90e1f057 Mon Sep 17 00:00:00 2001 From: Shubhrajyoti D Date: Wed, 3 Aug 2011 13:58:08 +0530 Subject: OMAP4: I2C: Enable the wakeup in I2C_WE Currently for OMAP4 the I2C_WE is not programmed. This patch enables the programming for OMAP4. This patch fixes a bad conflict resolution. This effectively restores the following commit Commit 120bdaa47[i2c-omap: Program I2C_WE on OMAP4 to enable i2c wakeup] which got changed by Commit a3a7acbc[I2C: OMAP2+: address confused probed version naming] Reviewed-by: Felipe Balbi Reported-by: Santosh Shilimkar Signed-off-by: Shubhrajyoti D Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 642a233..5df938f 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -384,9 +384,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) * REVISIT: Some wkup sources might not be needed. */ dev->westate = OMAP_I2C_WE_ALL; - if (dev->rev < OMAP_I2C_REV_ON_3530_4430) - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, - dev->westate); + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, + dev->westate); } } omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); -- cgit v0.10.2 From 7f4b08eeeedd90d97c8c581d048074e0c2643bec Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 17 May 2011 16:31:37 +0200 Subject: I2C: OMAP: remove unneccesary use of pdev A pointer to the struct device associated with the i2c device is already kept in the struct omap_i2c_dev, so use omap_i2c_device to find the pointer to struct device. Reviewed-by: Felipe Balbi Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 5df938f..cddb29c 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -267,15 +267,13 @@ static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg) static void omap_i2c_unidle(struct omap_i2c_dev *dev) { - struct platform_device *pdev; struct omap_i2c_bus_platform_data *pdata; WARN_ON(!dev->idle); - pdev = to_platform_device(dev->dev); - pdata = pdev->dev.platform_data; + pdata = dev->dev->platform_data; - pm_runtime_get_sync(&pdev->dev); + pm_runtime_get_sync(dev->dev); if (pdata->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); @@ -299,14 +297,12 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev) static void omap_i2c_idle(struct omap_i2c_dev *dev) { - struct platform_device *pdev; struct omap_i2c_bus_platform_data *pdata; u16 iv; WARN_ON(dev->idle); - pdev = to_platform_device(dev->dev); - pdata = pdev->dev.platform_data; + pdata = dev->dev->platform_data; dev->iestate = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG); if (pdata->rev == OMAP_I2C_IP_VERSION_2) @@ -324,7 +320,7 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev) } dev->idle = 1; - pm_runtime_put_sync(&pdev->dev); + pm_runtime_put_sync(dev->dev); } static int omap_i2c_init(struct omap_i2c_dev *dev) @@ -335,11 +331,9 @@ static int omap_i2c_init(struct omap_i2c_dev *dev) unsigned long timeout; unsigned long internal_clk = 0; struct clk *fclk; - struct platform_device *pdev; struct omap_i2c_bus_platform_data *pdata; - pdev = to_platform_device(dev->dev); - pdata = pdev->dev.platform_data; + pdata = dev->dev->platform_data; if (dev->rev >= OMAP_I2C_OMAP1_REV_2) { /* Disable I2C controller before soft reset */ @@ -821,11 +815,9 @@ omap_i2c_isr(int this_irq, void *dev_id) u16 bits; u16 stat, w; int err, count = 0; - struct platform_device *pdev; struct omap_i2c_bus_platform_data *pdata; - pdev = to_platform_device(dev->dev); - pdata = pdev->dev.platform_data; + pdata = dev->dev->platform_data; if (dev->idle) return IRQ_NONE; @@ -1047,7 +1039,7 @@ omap_i2c_probe(struct platform_device *pdev) else dev->regs = (u8 *)reg_map_ip_v1; - pm_runtime_enable(&pdev->dev); + pm_runtime_enable(dev->dev); omap_i2c_unidle(dev); dev->rev = omap_i2c_read_reg(dev, OMAP_I2C_REV_REG) & 0xff; -- cgit v0.10.2 From fab67afb543c734c23be0ebfc16f31814df2da79 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 17 May 2011 16:31:38 +0200 Subject: I2C: OMAP: remove dev->idle, use usage counting provided by runtime PM Current usage of runtime PM is not quite correct. The actual idle/unidle of the I2C hardware should not happen until the runtime PM callbacks are called. Therefore, change omap_i2c_[un]idle() functions to only be called from the runtime PM callbacks (when usage count transitions to/from zero.) Also, the runtime PM core does usage counting and replaces functionality currently managed by the dev->idle flag. Remove usage of dev->idle in favor of using runtime PM, and checking status using pm_runtime_suspended(). Signed-off-by: Kevin Hilman diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index cddb29c..a43d002 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -194,7 +194,6 @@ struct omap_i2c_dev { */ u8 rev; unsigned b_hw:1; /* bad h/w fixes */ - unsigned idle:1; u16 iestate; /* Saved interrupt register */ u16 pscstate; u16 scllstate; @@ -269,12 +268,8 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev) { struct omap_i2c_bus_platform_data *pdata; - WARN_ON(!dev->idle); - pdata = dev->dev->platform_data; - pm_runtime_get_sync(dev->dev); - if (pdata->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) { omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate); @@ -285,7 +280,6 @@ static void omap_i2c_unidle(struct omap_i2c_dev *dev) omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate); omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN); } - dev->idle = 0; /* * Don't write to this register if the IE state is 0 as it can @@ -300,8 +294,6 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev) struct omap_i2c_bus_platform_data *pdata; u16 iv; - WARN_ON(dev->idle); - pdata = dev->dev->platform_data; dev->iestate = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG); @@ -315,12 +307,9 @@ static void omap_i2c_idle(struct omap_i2c_dev *dev) } else { omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, dev->iestate); - /* Flush posted write before the dev->idle store occurs */ + /* Flush posted write */ omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG); } - dev->idle = 1; - - pm_runtime_put_sync(dev->dev); } static int omap_i2c_init(struct omap_i2c_dev *dev) @@ -644,7 +633,7 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) int i; int r; - omap_i2c_unidle(dev); + pm_runtime_get_sync(dev->dev); r = omap_i2c_wait_for_bb(dev); if (r < 0) @@ -667,7 +656,7 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) omap_i2c_wait_for_bb(dev); out: - omap_i2c_idle(dev); + pm_runtime_put(dev->dev); return r; } @@ -727,7 +716,7 @@ omap_i2c_omap1_isr(int this_irq, void *dev_id) struct omap_i2c_dev *dev = dev_id; u16 iv, w; - if (dev->idle) + if (pm_runtime_suspended(dev->dev)) return IRQ_NONE; iv = omap_i2c_read_reg(dev, OMAP_I2C_IV_REG); @@ -819,7 +808,7 @@ omap_i2c_isr(int this_irq, void *dev_id) pdata = dev->dev->platform_data; - if (dev->idle) + if (pm_runtime_suspended(dev->dev)) return IRQ_NONE; bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG); @@ -1021,7 +1010,6 @@ omap_i2c_probe(struct platform_device *pdev) } dev->speed = speed; - dev->idle = 1; dev->dev = &pdev->dev; dev->irq = irq->start; dev->base = ioremap(mem->start, resource_size(mem)); @@ -1040,7 +1028,7 @@ omap_i2c_probe(struct platform_device *pdev) dev->regs = (u8 *)reg_map_ip_v1; pm_runtime_enable(dev->dev); - omap_i2c_unidle(dev); + pm_runtime_get_sync(dev->dev); dev->rev = omap_i2c_read_reg(dev, OMAP_I2C_REV_REG) & 0xff; @@ -1087,7 +1075,7 @@ omap_i2c_probe(struct platform_device *pdev) dev_info(dev->dev, "bus %d rev%d.%d.%d at %d kHz\n", pdev->id, pdata->rev, dev->rev >> 4, dev->rev & 0xf, dev->speed); - omap_i2c_idle(dev); + pm_runtime_put(dev->dev); adap = &dev->adapter; i2c_set_adapdata(adap, dev); @@ -1111,7 +1099,7 @@ err_free_irq: free_irq(dev->irq, dev); err_unuse_clocks: omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0); - omap_i2c_idle(dev); + pm_runtime_put(dev->dev); iounmap(dev->base); err_free_mem: platform_set_drvdata(pdev, NULL); @@ -1140,12 +1128,43 @@ omap_i2c_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM_RUNTIME +static int omap_i2c_runtime_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct omap_i2c_dev *_dev = platform_get_drvdata(pdev); + + omap_i2c_idle(_dev); + + return 0; +} + +static int omap_i2c_runtime_resume(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct omap_i2c_dev *_dev = platform_get_drvdata(pdev); + + omap_i2c_unidle(_dev); + + return 0; +} + +static struct dev_pm_ops omap_i2c_pm_ops = { + .runtime_suspend = omap_i2c_runtime_suspend, + .runtime_resume = omap_i2c_runtime_resume, +}; +#define OMAP_I2C_PM_OPS (&omap_i2c_pm_ops) +#else +#define OMAP_I2C_PM_OPS NULL +#endif + static struct platform_driver omap_i2c_driver = { .probe = omap_i2c_probe, .remove = omap_i2c_remove, .driver = { .name = "omap_i2c", .owner = THIS_MODULE, + .pm = OMAP_I2C_PM_OPS, }, }; -- cgit v0.10.2 From c9c7ae40660f5983854f73b6ae65f208e9a15082 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Thu, 4 Aug 2011 08:01:56 -0700 Subject: I2C: OMAP: remove unused function pointers from pdata Now that this driver is using runtime PM, there is no longer a need for the idle/enable/shutdown function pointers in pdata. Signed-off-by: Kevin Hilman diff --git a/include/linux/i2c-omap.h b/include/linux/i2c-omap.h index 56a9924..92a0dc7 100644 --- a/include/linux/i2c-omap.h +++ b/include/linux/i2c-omap.h @@ -35,9 +35,6 @@ struct omap_i2c_bus_platform_data { u32 rev; u32 flags; void (*set_mpu_wkup_lat)(struct device *dev, long set); - int (*device_enable) (struct platform_device *pdev); - int (*device_shutdown) (struct platform_device *pdev); - int (*device_idle) (struct platform_device *pdev); }; #endif -- cgit v0.10.2 From 4311051c358ad0e66b68934e7a33cf10ba533466 Mon Sep 17 00:00:00 2001 From: Yong Zhang Date: Wed, 21 Sep 2011 17:28:33 +0800 Subject: i2c: irq: Remove IRQF_DISABLED Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled], We run all interrupt handlers with interrupts disabled and we even check and yell when an interrupt handler returns with interrupts enabled (see commit [b738a50a: genirq: Warn when handler enables interrupts]). So now this flag is a NOOP and can be removed. Signed-off-by: Yong Zhang Acked-by: Wolfram Sang Acked-by: Linus Walleij Acked-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-bfin-twi.c b/drivers/i2c/busses/i2c-bfin-twi.c index cbc98ae..cdb59e5 100644 --- a/drivers/i2c/busses/i2c-bfin-twi.c +++ b/drivers/i2c/busses/i2c-bfin-twi.c @@ -631,7 +631,7 @@ static int i2c_bfin_twi_resume(struct platform_device *pdev) struct bfin_twi_iface *iface = platform_get_drvdata(pdev); int rc = request_irq(iface->irq, bfin_twi_interrupt_entry, - IRQF_DISABLED, pdev->name, iface); + 0, pdev->name, iface); if (rc) { dev_err(&pdev->dev, "Can't get IRQ %d !\n", iface->irq); return -ENODEV; @@ -702,7 +702,7 @@ static int i2c_bfin_twi_probe(struct platform_device *pdev) } rc = request_irq(iface->irq, bfin_twi_interrupt_entry, - IRQF_DISABLED, pdev->name, iface); + 0, pdev->name, iface); if (rc) { dev_err(&pdev->dev, "Can't get IRQ %d !\n", iface->irq); rc = -ENODEV; diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c index 1b42b50..2ac1903 100644 --- a/drivers/i2c/busses/i2c-designware.c +++ b/drivers/i2c/busses/i2c-designware.c @@ -755,7 +755,7 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) i2c_dw_init(dev); writel(0, dev->base + DW_IC_INTR_MASK); /* disable IRQ */ - r = request_irq(dev->irq, i2c_dw_isr, IRQF_DISABLED, pdev->name, dev); + r = request_irq(dev->irq, i2c_dw_isr, 0, pdev->name, dev); if (r) { dev_err(&pdev->dev, "failure requesting irq %i\n", dev->irq); goto err_iounmap; diff --git a/drivers/i2c/busses/i2c-highlander.c b/drivers/i2c/busses/i2c-highlander.c index 3876a24..63bb1cc 100644 --- a/drivers/i2c/busses/i2c-highlander.c +++ b/drivers/i2c/busses/i2c-highlander.c @@ -387,7 +387,7 @@ static int __devinit highlander_i2c_probe(struct platform_device *pdev) dev->irq = 0; if (dev->irq) { - ret = request_irq(dev->irq, highlander_i2c_irq, IRQF_DISABLED, + ret = request_irq(dev->irq, highlander_i2c_irq, 0, pdev->name, dev); if (unlikely(ret)) goto err_unmap; diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c index b228e09..40702e8 100644 --- a/drivers/i2c/busses/i2c-nomadik.c +++ b/drivers/i2c/busses/i2c-nomadik.c @@ -935,7 +935,7 @@ static int __devinit nmk_i2c_probe(struct platform_device *pdev) } dev->irq = platform_get_irq(pdev, 0); - ret = request_irq(dev->irq, i2c_irq_handler, IRQF_DISABLED, + ret = request_irq(dev->irq, i2c_irq_handler, 0, DRIVER_NAME, dev); if (ret) { dev_err(&pdev->dev, "cannot claim the irq %d\n", dev->irq); diff --git a/drivers/i2c/busses/i2c-nuc900.c b/drivers/i2c/busses/i2c-nuc900.c index 7243426..835e47b 100644 --- a/drivers/i2c/busses/i2c-nuc900.c +++ b/drivers/i2c/busses/i2c-nuc900.c @@ -610,7 +610,7 @@ static int __devinit nuc900_i2c_probe(struct platform_device *pdev) goto err_iomap; } - ret = request_irq(i2c->irq, nuc900_i2c_irq, IRQF_DISABLED | IRQF_SHARED, + ret = request_irq(i2c->irq, nuc900_i2c_irq, IRQF_SHARED, dev_name(&pdev->dev), i2c); if (ret != 0) { diff --git a/drivers/i2c/busses/i2c-pmcmsp.c b/drivers/i2c/busses/i2c-pmcmsp.c index dfa7ae9..127051b 100644 --- a/drivers/i2c/busses/i2c-pmcmsp.c +++ b/drivers/i2c/busses/i2c-pmcmsp.c @@ -306,7 +306,7 @@ static int __devinit pmcmsptwi_probe(struct platform_device *pldev) pmcmsptwi_data.irq = platform_get_irq(pldev, 0); if (pmcmsptwi_data.irq) { rc = request_irq(pmcmsptwi_data.irq, &pmcmsptwi_interrupt, - IRQF_SHARED | IRQF_DISABLED | IRQF_SAMPLE_RANDOM, + IRQF_SHARED | IRQF_SAMPLE_RANDOM, pldev->name, &pmcmsptwi_data); if (rc == 0) { /* diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index f84a63c..545ca88 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -883,7 +883,7 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev) goto err_iomap; } - ret = request_irq(i2c->irq, s3c24xx_i2c_irq, IRQF_DISABLED, + ret = request_irq(i2c->irq, s3c24xx_i2c_irq, 0, dev_name(&pdev->dev), i2c); if (ret != 0) { diff --git a/drivers/i2c/busses/i2c-sh7760.c b/drivers/i2c/busses/i2c-sh7760.c index 3cad8fe..c418c41 100644 --- a/drivers/i2c/busses/i2c-sh7760.c +++ b/drivers/i2c/busses/i2c-sh7760.c @@ -502,7 +502,7 @@ static int __devinit sh7760_i2c_probe(struct platform_device *pdev) } OUT32(id, I2CCCR, ret); - if (request_irq(id->irq, sh7760_i2c_irq, IRQF_DISABLED, + if (request_irq(id->irq, sh7760_i2c_irq, 0, SH7760_I2C_DEVNAME, id)) { dev_err(&pdev->dev, "cannot get irq %d\n", id->irq); ret = -EBUSY; diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index f633a53..675c969 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -543,7 +543,7 @@ static int sh_mobile_i2c_hook_irqs(struct platform_device *dev, int hook) while ((res = platform_get_resource(dev, IORESOURCE_IRQ, k))) { for (n = res->start; hook && n <= res->end; n++) { - if (request_irq(n, sh_mobile_i2c_isr, IRQF_DISABLED, + if (request_irq(n, sh_mobile_i2c_isr, 0, dev_name(&dev->dev), dev)) { for (n--; n >= res->start; n--) free_irq(n, dev); diff --git a/drivers/i2c/busses/i2c-stu300.c b/drivers/i2c/busses/i2c-stu300.c index 9987961..4d44af1 100644 --- a/drivers/i2c/busses/i2c-stu300.c +++ b/drivers/i2c/busses/i2c-stu300.c @@ -916,7 +916,7 @@ stu300_probe(struct platform_device *pdev) } dev->irq = platform_get_irq(pdev, 0); - if (request_irq(dev->irq, stu300_irh, IRQF_DISABLED, + if (request_irq(dev->irq, stu300_irh, 0, NAME, dev)) { ret = -EIO; goto err_no_irq; -- cgit v0.10.2 From 7f279601c59b814314083d572e7c0df11d09cad8 Mon Sep 17 00:00:00 2001 From: Jean-Hugues Deschenes Date: Thu, 6 Oct 2011 11:26:25 -0700 Subject: i2c-designware: Use local version of readl & writel Use local versions of readl & writel, so per-access manipulations may be performed Signed-off-by: Jean-Hugues Deschenes Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c index 1b42b50..28335c3 100644 --- a/drivers/i2c/busses/i2c-designware.c +++ b/drivers/i2c/busses/i2c-designware.c @@ -220,6 +220,16 @@ struct dw_i2c_dev { unsigned int rx_fifo_depth; }; +static u32 dw_readl(struct dw_i2c_dev *dev, int offset) +{ + return readl(dev->base + offset); +} + +static void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset) +{ + writel(b, dev->base + offset); +} + static u32 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset) { @@ -289,7 +299,7 @@ static void i2c_dw_init(struct dw_i2c_dev *dev) u32 ic_con, hcnt, lcnt; /* Disable the adapter */ - writel(0, dev->base + DW_IC_ENABLE); + dw_writel(dev, 0, DW_IC_ENABLE); /* set standard and fast speed deviders for high/low periods */ @@ -303,8 +313,8 @@ static void i2c_dw_init(struct dw_i2c_dev *dev) 47, /* tLOW = 4.7 us */ 3, /* tf = 0.3 us */ 0); /* No offset */ - writel(hcnt, dev->base + DW_IC_SS_SCL_HCNT); - writel(lcnt, dev->base + DW_IC_SS_SCL_LCNT); + dw_writel(dev, hcnt, DW_IC_SS_SCL_HCNT); + dw_writel(dev, lcnt, DW_IC_SS_SCL_LCNT); dev_dbg(dev->dev, "Standard-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt); /* Fast-mode */ @@ -317,18 +327,18 @@ static void i2c_dw_init(struct dw_i2c_dev *dev) 13, /* tLOW = 1.3 us */ 3, /* tf = 0.3 us */ 0); /* No offset */ - writel(hcnt, dev->base + DW_IC_FS_SCL_HCNT); - writel(lcnt, dev->base + DW_IC_FS_SCL_LCNT); + dw_writel(dev, hcnt, DW_IC_FS_SCL_HCNT); + dw_writel(dev, lcnt, DW_IC_FS_SCL_LCNT); dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt); /* Configure Tx/Rx FIFO threshold levels */ - writel(dev->tx_fifo_depth - 1, dev->base + DW_IC_TX_TL); - writel(0, dev->base + DW_IC_RX_TL); + dw_writel(dev, dev->tx_fifo_depth - 1, DW_IC_TX_TL); + dw_writel(dev, 0, DW_IC_RX_TL); /* configure the i2c master */ ic_con = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE | DW_IC_CON_RESTART_EN | DW_IC_CON_SPEED_FAST; - writel(ic_con, dev->base + DW_IC_CON); + dw_writel(dev, ic_con, DW_IC_CON); } /* @@ -338,7 +348,7 @@ static int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev) { int timeout = TIMEOUT; - while (readl(dev->base + DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) { + while (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) { if (timeout <= 0) { dev_warn(dev->dev, "timeout waiting for bus ready\n"); return -ETIMEDOUT; @@ -356,24 +366,24 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev) u32 ic_con; /* Disable the adapter */ - writel(0, dev->base + DW_IC_ENABLE); + dw_writel(dev, 0, DW_IC_ENABLE); /* set the slave (target) address */ - writel(msgs[dev->msg_write_idx].addr, dev->base + DW_IC_TAR); + dw_writel(dev, msgs[dev->msg_write_idx].addr, DW_IC_TAR); /* if the slave address is ten bit address, enable 10BITADDR */ - ic_con = readl(dev->base + DW_IC_CON); + ic_con = dw_readl(dev, DW_IC_CON); if (msgs[dev->msg_write_idx].flags & I2C_M_TEN) ic_con |= DW_IC_CON_10BITADDR_MASTER; else ic_con &= ~DW_IC_CON_10BITADDR_MASTER; - writel(ic_con, dev->base + DW_IC_CON); + dw_writel(dev, ic_con, DW_IC_CON); /* Enable the adapter */ - writel(1, dev->base + DW_IC_ENABLE); + dw_writel(dev, 1, DW_IC_ENABLE); /* Enable interrupts */ - writel(DW_IC_INTR_DEFAULT_MASK, dev->base + DW_IC_INTR_MASK); + dw_writel(dev, DW_IC_INTR_DEFAULT_MASK, DW_IC_INTR_MASK); } /* @@ -420,15 +430,15 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev) buf_len = msgs[dev->msg_write_idx].len; } - tx_limit = dev->tx_fifo_depth - readl(dev->base + DW_IC_TXFLR); - rx_limit = dev->rx_fifo_depth - readl(dev->base + DW_IC_RXFLR); + tx_limit = dev->tx_fifo_depth - dw_readl(dev, DW_IC_TXFLR); + rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR); while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) { if (msgs[dev->msg_write_idx].flags & I2C_M_RD) { - writel(0x100, dev->base + DW_IC_DATA_CMD); + dw_writel(dev, 0x100, DW_IC_DATA_CMD); rx_limit--; } else - writel(*buf++, dev->base + DW_IC_DATA_CMD); + dw_writel(dev, *buf++, DW_IC_DATA_CMD); tx_limit--; buf_len--; } @@ -453,7 +463,7 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev) if (dev->msg_err) intr_mask = 0; - writel(intr_mask, dev->base + DW_IC_INTR_MASK); + dw_writel(dev, intr_mask, DW_IC_INTR_MASK); } static void @@ -477,10 +487,10 @@ i2c_dw_read(struct dw_i2c_dev *dev) buf = dev->rx_buf; } - rx_valid = readl(dev->base + DW_IC_RXFLR); + rx_valid = dw_readl(dev, DW_IC_RXFLR); for (; len > 0 && rx_valid > 0; len--, rx_valid--) - *buf++ = readl(dev->base + DW_IC_DATA_CMD); + *buf++ = dw_readl(dev, DW_IC_DATA_CMD); if (len > 0) { dev->status |= STATUS_READ_IN_PROGRESS; @@ -563,7 +573,7 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) /* no error */ if (likely(!dev->cmd_err)) { /* Disable the adapter */ - writel(0, dev->base + DW_IC_ENABLE); + dw_writel(dev, 0, DW_IC_ENABLE); ret = num; goto done; } @@ -607,7 +617,7 @@ static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev) * * The raw version might be useful for debugging purposes. */ - stat = readl(dev->base + DW_IC_INTR_STAT); + stat = dw_readl(dev, DW_IC_INTR_STAT); /* * Do not use the IC_CLR_INTR register to clear interrupts, or @@ -617,31 +627,31 @@ static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev) * Instead, use the separately-prepared IC_CLR_* registers. */ if (stat & DW_IC_INTR_RX_UNDER) - readl(dev->base + DW_IC_CLR_RX_UNDER); + dw_readl(dev, DW_IC_CLR_RX_UNDER); if (stat & DW_IC_INTR_RX_OVER) - readl(dev->base + DW_IC_CLR_RX_OVER); + dw_readl(dev, DW_IC_CLR_RX_OVER); if (stat & DW_IC_INTR_TX_OVER) - readl(dev->base + DW_IC_CLR_TX_OVER); + dw_readl(dev, DW_IC_CLR_TX_OVER); if (stat & DW_IC_INTR_RD_REQ) - readl(dev->base + DW_IC_CLR_RD_REQ); + dw_readl(dev, DW_IC_CLR_RD_REQ); if (stat & DW_IC_INTR_TX_ABRT) { /* * The IC_TX_ABRT_SOURCE register is cleared whenever * the IC_CLR_TX_ABRT is read. Preserve it beforehand. */ - dev->abort_source = readl(dev->base + DW_IC_TX_ABRT_SOURCE); - readl(dev->base + DW_IC_CLR_TX_ABRT); + dev->abort_source = dw_readl(dev, DW_IC_TX_ABRT_SOURCE); + dw_readl(dev, DW_IC_CLR_TX_ABRT); } if (stat & DW_IC_INTR_RX_DONE) - readl(dev->base + DW_IC_CLR_RX_DONE); + dw_readl(dev, DW_IC_CLR_RX_DONE); if (stat & DW_IC_INTR_ACTIVITY) - readl(dev->base + DW_IC_CLR_ACTIVITY); + dw_readl(dev, DW_IC_CLR_ACTIVITY); if (stat & DW_IC_INTR_STOP_DET) - readl(dev->base + DW_IC_CLR_STOP_DET); + dw_readl(dev, DW_IC_CLR_STOP_DET); if (stat & DW_IC_INTR_START_DET) - readl(dev->base + DW_IC_CLR_START_DET); + dw_readl(dev, DW_IC_CLR_START_DET); if (stat & DW_IC_INTR_GEN_CALL) - readl(dev->base + DW_IC_CLR_GEN_CALL); + dw_readl(dev, DW_IC_CLR_GEN_CALL); return stat; } @@ -666,7 +676,7 @@ static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id) * Anytime TX_ABRT is set, the contents of the tx/rx * buffers are flushed. Make sure to skip them. */ - writel(0, dev->base + DW_IC_INTR_MASK); + dw_writel(dev, 0, DW_IC_INTR_MASK); goto tx_aborted; } @@ -747,14 +757,14 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) goto err_unuse_clocks; } { - u32 param1 = readl(dev->base + DW_IC_COMP_PARAM_1); + u32 param1 = dw_readl(dev, DW_IC_COMP_PARAM_1); dev->tx_fifo_depth = ((param1 >> 16) & 0xff) + 1; dev->rx_fifo_depth = ((param1 >> 8) & 0xff) + 1; } i2c_dw_init(dev); - writel(0, dev->base + DW_IC_INTR_MASK); /* disable IRQ */ + dw_writel(dev, 0, DW_IC_INTR_MASK); /* disable IRQ */ r = request_irq(dev->irq, i2c_dw_isr, IRQF_DISABLED, pdev->name, dev); if (r) { dev_err(&pdev->dev, "failure requesting irq %i\n", dev->irq); @@ -810,7 +820,7 @@ static int __devexit dw_i2c_remove(struct platform_device *pdev) clk_put(dev->clk); dev->clk = NULL; - writel(0, dev->base + DW_IC_ENABLE); + dw_writel(dev, 0, DW_IC_ENABLE); free_irq(dev->irq, dev); kfree(dev); -- cgit v0.10.2 From 4ff895bc8b90e30ff8e89ca7bc6666b229c77e5d Mon Sep 17 00:00:00 2001 From: Jean-Hugues Deschenes Date: Thu, 6 Oct 2011 11:26:26 -0700 Subject: i2c-designware: Check component type register Designware component type register is checked before attaching to the device. Signed-off-by: Jean-Hugues Deschenes Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c index 28335c3..4938695 100644 --- a/drivers/i2c/busses/i2c-designware.c +++ b/drivers/i2c/busses/i2c-designware.c @@ -69,6 +69,7 @@ #define DW_IC_TXFLR 0x74 #define DW_IC_RXFLR 0x78 #define DW_IC_COMP_PARAM_1 0xf4 +#define DW_IC_COMP_TYPE 0xfc #define DW_IC_TX_ABRT_SOURCE 0x80 #define DW_IC_CON_MASTER 0x1 @@ -710,6 +711,7 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) struct i2c_adapter *adap; struct resource *mem, *ioarea; int irq, r; + u32 reg; /* NOTE: driver uses the static register mapping */ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -756,12 +758,19 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) r = -EBUSY; goto err_unuse_clocks; } - { - u32 param1 = dw_readl(dev, DW_IC_COMP_PARAM_1); - dev->tx_fifo_depth = ((param1 >> 16) & 0xff) + 1; - dev->rx_fifo_depth = ((param1 >> 8) & 0xff) + 1; + reg = dw_readl(dev, DW_IC_COMP_TYPE); + if (reg != 0x44570140) { + dev_err(&pdev->dev, "Unknown Synopsys component type: " + "0x%08x\n", reg); + r = -ENODEV; + goto err_iounmap; } + + reg = dw_readl(dev, DW_IC_COMP_PARAM_1); + dev->tx_fifo_depth = ((reg >> 16) & 0xff) + 1; + dev->rx_fifo_depth = ((reg >> 8) & 0xff) + 1; + i2c_dw_init(dev); dw_writel(dev, 0, DW_IC_INTR_MASK); /* disable IRQ */ -- cgit v0.10.2 From 18c4089e6cd6b3052895481628f478ba8351ac00 Mon Sep 17 00:00:00 2001 From: Jean-Hugues Deschenes Date: Thu, 6 Oct 2011 11:26:27 -0700 Subject: i2c-designware: Allow mixed endianness accesses Allows CPUs of a given endianness to access a dw controller of a different endianness. Endianncess difference is detected at run time through the dw component type register. Signed-off-by: Jean-Hugues Deschenes Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c index 4938695..934dfe1 100644 --- a/drivers/i2c/busses/i2c-designware.c +++ b/drivers/i2c/busses/i2c-designware.c @@ -37,6 +37,7 @@ #include #include #include +#include /* * Registers offset @@ -193,6 +194,7 @@ static char *abort_sources[] = { * @status: i2c master status, one of STATUS_* * @abort_source: copy of the TX_ABRT_SOURCE register * @irq: interrupt number for the i2c master + * @swab: true if the instantiated IP is of different endianess * @adapter: i2c subsystem adapter node * @tx_fifo_depth: depth of the hardware tx fifo * @rx_fifo_depth: depth of the hardware rx fifo @@ -216,6 +218,7 @@ struct dw_i2c_dev { unsigned int status; u32 abort_source; int irq; + int swab; struct i2c_adapter adapter; unsigned int tx_fifo_depth; unsigned int rx_fifo_depth; @@ -223,11 +226,19 @@ struct dw_i2c_dev { static u32 dw_readl(struct dw_i2c_dev *dev, int offset) { - return readl(dev->base + offset); + u32 value = readl(dev->base + offset); + + if (dev->swab) + return swab32(value); + else + return value; } static void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset) { + if (dev->swab) + b = swab32(b); + writel(b, dev->base + offset); } @@ -760,7 +771,9 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) } reg = dw_readl(dev, DW_IC_COMP_TYPE); - if (reg != 0x44570140) { + if (reg == ___constant_swab32(0x44570140)) + dev->swab = 1; + else if (reg != 0x44570140) { dev_err(&pdev->dev, "Unknown Synopsys component type: " "0x%08x\n", reg); r = -ENODEV; -- cgit v0.10.2 From 4a423a8c8107b983007199c76c8327cd1747f092 Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:28 -0700 Subject: i2c-designware: Move checking of IP core version to i2c_dw_init() Move checking IP core version to i2c_dw_init() in preparation for splitting i2c-designware.c into core and bus specific portions. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c index 934dfe1..a7abbcd 100644 --- a/drivers/i2c/busses/i2c-designware.c +++ b/drivers/i2c/busses/i2c-designware.c @@ -305,10 +305,24 @@ static u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset) * This function is called during I2C init function, and in case of timeout at * run time. */ -static void i2c_dw_init(struct dw_i2c_dev *dev) +static int i2c_dw_init(struct dw_i2c_dev *dev) { u32 input_clock_khz = clk_get_rate(dev->clk) / 1000; u32 ic_con, hcnt, lcnt; + u32 reg; + + /* Configure register endianess access */ + reg = dw_readl(dev, DW_IC_COMP_TYPE); + if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) { + dev->swab = 1; + reg = DW_IC_COMP_TYPE_VALUE; + } + + if (reg != DW_IC_COMP_TYPE_VALUE) { + dev_err(dev->dev, "Unknown Synopsys component type: " + "0x%08x\n", reg); + return -ENODEV; + } /* Disable the adapter */ dw_writel(dev, 0, DW_IC_ENABLE); @@ -351,6 +365,7 @@ static void i2c_dw_init(struct dw_i2c_dev *dev) ic_con = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE | DW_IC_CON_RESTART_EN | DW_IC_CON_SPEED_FAST; dw_writel(dev, ic_con, DW_IC_CON); + return 0; } /* @@ -770,21 +785,14 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) goto err_unuse_clocks; } - reg = dw_readl(dev, DW_IC_COMP_TYPE); - if (reg == ___constant_swab32(0x44570140)) - dev->swab = 1; - else if (reg != 0x44570140) { - dev_err(&pdev->dev, "Unknown Synopsys component type: " - "0x%08x\n", reg); - r = -ENODEV; - goto err_iounmap; - } + r = i2c_dw_init(dev); + if (r) + goto err_unuse_clocks; reg = dw_readl(dev, DW_IC_COMP_PARAM_1); dev->tx_fifo_depth = ((reg >> 16) & 0xff) + 1; dev->rx_fifo_depth = ((reg >> 8) & 0xff) + 1; - i2c_dw_init(dev); dw_writel(dev, 0, DW_IC_INTR_MASK); /* disable IRQ */ r = request_irq(dev->irq, i2c_dw_isr, IRQF_DISABLED, pdev->name, dev); -- cgit v0.10.2 From 2373f6b9744d5373b886f3ce1a985193cca0a356 Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Sat, 29 Oct 2011 10:57:23 +0100 Subject: i2c-designware: split of i2c-designware.c into core and bus specific parts This patch splits i2c-designware.c into three pieces: i2c-designware-core.c, contains the code that interacts directly with the core. i2c-designware-platdrv.c, contains the code specific to the platform driver using the core. i2c-designware-core.h contains the definitions and declareations shared by i2c-designware-core.c and i2c-designware-platdrv.c. This patch is the first in a set to allow multiple instances of the designware I2C core in the system. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 646068e..e6f6e88 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -350,15 +350,15 @@ config I2C_DAVINCI devices such as DaVinci NIC. For details please see http://www.ti.com/davinci -config I2C_DESIGNWARE - tristate "Synopsys DesignWare" +config I2C_DESIGNWARE_PLATFORM + tristate "Synopsys DesignWare Platfrom" depends on HAVE_CLK help If you say yes to this option, support will be included for the Synopsys DesignWare I2C adapter. Only master mode is supported. This driver can also be built as a module. If so, the module - will be called i2c-designware. + will be called i2c-designware-platform. config I2C_GPIO tristate "GPIO-based bitbanging I2C" diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index e6cf294..d7fe55f 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -33,7 +33,8 @@ obj-$(CONFIG_I2C_AU1550) += i2c-au1550.o obj-$(CONFIG_I2C_BLACKFIN_TWI) += i2c-bfin-twi.o obj-$(CONFIG_I2C_CPM) += i2c-cpm.o obj-$(CONFIG_I2C_DAVINCI) += i2c-davinci.o -obj-$(CONFIG_I2C_DESIGNWARE) += i2c-designware.o +obj-$(CONFIG_I2C_DESIGNWARE_PLATFORM) += i2c-designware-platform.o +i2c-designware-platform-objs := i2c-designware-platdrv.o i2c-designware-core.o obj-$(CONFIG_I2C_GPIO) += i2c-gpio.o obj-$(CONFIG_I2C_HIGHLANDER) += i2c-highlander.o obj-$(CONFIG_I2C_IBM_IIC) += i2c-ibm_iic.o diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c new file mode 100644 index 0000000..38d5a6b --- /dev/null +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -0,0 +1,562 @@ +/* + * Synopsys DesignWare I2C adapter driver (master only). + * + * Based on the TI DAVINCI I2C adapter driver. + * + * Copyright (C) 2006 Texas Instruments. + * Copyright (C) 2007 MontaVista Software Inc. + * Copyright (C) 2009 Provigent Ltd. + * + * ---------------------------------------------------------------------------- + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + * + */ +#include +#include +#include +#include +#include +#include +#include +#include "i2c-designware-core.h" + +static char *abort_sources[] = { + [ABRT_7B_ADDR_NOACK] = + "slave address not acknowledged (7bit mode)", + [ABRT_10ADDR1_NOACK] = + "first address byte not acknowledged (10bit mode)", + [ABRT_10ADDR2_NOACK] = + "second address byte not acknowledged (10bit mode)", + [ABRT_TXDATA_NOACK] = + "data not acknowledged", + [ABRT_GCALL_NOACK] = + "no acknowledgement for a general call", + [ABRT_GCALL_READ] = + "read after general call", + [ABRT_SBYTE_ACKDET] = + "start byte acknowledged", + [ABRT_SBYTE_NORSTRT] = + "trying to send start byte when restart is disabled", + [ABRT_10B_RD_NORSTRT] = + "trying to read when restart is disabled (10bit mode)", + [ABRT_MASTER_DIS] = + "trying to use disabled adapter", + [ARB_LOST] = + "lost arbitration", +}; + +u32 dw_readl(struct dw_i2c_dev *dev, int offset) +{ + u32 value = readl(dev->base + offset); + + if (dev->swab) + return swab32(value); + else + return value; +} + +void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset) +{ + if (dev->swab) + b = swab32(b); + + writel(b, dev->base + offset); +} + +static u32 +i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset) +{ + /* + * DesignWare I2C core doesn't seem to have solid strategy to meet + * the tHD;STA timing spec. Configuring _HCNT based on tHIGH spec + * will result in violation of the tHD;STA spec. + */ + if (cond) + /* + * Conditional expression: + * + * IC_[FS]S_SCL_HCNT + (1+4+3) >= IC_CLK * tHIGH + * + * This is based on the DW manuals, and represents an ideal + * configuration. The resulting I2C bus speed will be + * faster than any of the others. + * + * If your hardware is free from tHD;STA issue, try this one. + */ + return (ic_clk * tSYMBOL + 5000) / 10000 - 8 + offset; + else + /* + * Conditional expression: + * + * IC_[FS]S_SCL_HCNT + 3 >= IC_CLK * (tHD;STA + tf) + * + * This is just experimental rule; the tHD;STA period turned + * out to be proportinal to (_HCNT + 3). With this setting, + * we could meet both tHIGH and tHD;STA timing specs. + * + * If unsure, you'd better to take this alternative. + * + * The reason why we need to take into account "tf" here, + * is the same as described in i2c_dw_scl_lcnt(). + */ + return (ic_clk * (tSYMBOL + tf) + 5000) / 10000 - 3 + offset; +} + +static u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset) +{ + /* + * Conditional expression: + * + * IC_[FS]S_SCL_LCNT + 1 >= IC_CLK * (tLOW + tf) + * + * DW I2C core starts counting the SCL CNTs for the LOW period + * of the SCL clock (tLOW) as soon as it pulls the SCL line. + * In order to meet the tLOW timing spec, we need to take into + * account the fall time of SCL signal (tf). Default tf value + * should be 0.3 us, for safety. + */ + return ((ic_clk * (tLOW + tf) + 5000) / 10000) - 1 + offset; +} + +/** + * i2c_dw_init() - initialize the designware i2c master hardware + * @dev: device private data + * + * This functions configures and enables the I2C master. + * This function is called during I2C init function, and in case of timeout at + * run time. + */ +int i2c_dw_init(struct dw_i2c_dev *dev) +{ + u32 input_clock_khz = clk_get_rate(dev->clk) / 1000; + u32 ic_con, hcnt, lcnt; + u32 reg; + + /* Configure register endianess access */ + reg = dw_readl(dev, DW_IC_COMP_TYPE); + if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) { + dev->swab = 1; + reg = DW_IC_COMP_TYPE_VALUE; + } + + if (reg != DW_IC_COMP_TYPE_VALUE) { + dev_err(dev->dev, "Unknown Synopsys component type: " + "0x%08x\n", reg); + return -ENODEV; + } + + /* Disable the adapter */ + dw_writel(dev, 0, DW_IC_ENABLE); + + /* set standard and fast speed deviders for high/low periods */ + + /* Standard-mode */ + hcnt = i2c_dw_scl_hcnt(input_clock_khz, + 40, /* tHD;STA = tHIGH = 4.0 us */ + 3, /* tf = 0.3 us */ + 0, /* 0: DW default, 1: Ideal */ + 0); /* No offset */ + lcnt = i2c_dw_scl_lcnt(input_clock_khz, + 47, /* tLOW = 4.7 us */ + 3, /* tf = 0.3 us */ + 0); /* No offset */ + dw_writel(dev, hcnt, DW_IC_SS_SCL_HCNT); + dw_writel(dev, lcnt, DW_IC_SS_SCL_LCNT); + dev_dbg(dev->dev, "Standard-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt); + + /* Fast-mode */ + hcnt = i2c_dw_scl_hcnt(input_clock_khz, + 6, /* tHD;STA = tHIGH = 0.6 us */ + 3, /* tf = 0.3 us */ + 0, /* 0: DW default, 1: Ideal */ + 0); /* No offset */ + lcnt = i2c_dw_scl_lcnt(input_clock_khz, + 13, /* tLOW = 1.3 us */ + 3, /* tf = 0.3 us */ + 0); /* No offset */ + dw_writel(dev, hcnt, DW_IC_FS_SCL_HCNT); + dw_writel(dev, lcnt, DW_IC_FS_SCL_LCNT); + dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt); + + /* Configure Tx/Rx FIFO threshold levels */ + dw_writel(dev, dev->tx_fifo_depth - 1, DW_IC_TX_TL); + dw_writel(dev, 0, DW_IC_RX_TL); + + /* configure the i2c master */ + ic_con = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE | + DW_IC_CON_RESTART_EN | DW_IC_CON_SPEED_FAST; + dw_writel(dev, ic_con, DW_IC_CON); + return 0; +} + +/* + * Waiting for bus not busy + */ +static int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev) +{ + int timeout = TIMEOUT; + + while (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) { + if (timeout <= 0) { + dev_warn(dev->dev, "timeout waiting for bus ready\n"); + return -ETIMEDOUT; + } + timeout--; + mdelay(1); + } + + return 0; +} + +static void i2c_dw_xfer_init(struct dw_i2c_dev *dev) +{ + struct i2c_msg *msgs = dev->msgs; + u32 ic_con; + + /* Disable the adapter */ + dw_writel(dev, 0, DW_IC_ENABLE); + + /* set the slave (target) address */ + dw_writel(dev, msgs[dev->msg_write_idx].addr, DW_IC_TAR); + + /* if the slave address is ten bit address, enable 10BITADDR */ + ic_con = dw_readl(dev, DW_IC_CON); + if (msgs[dev->msg_write_idx].flags & I2C_M_TEN) + ic_con |= DW_IC_CON_10BITADDR_MASTER; + else + ic_con &= ~DW_IC_CON_10BITADDR_MASTER; + dw_writel(dev, ic_con, DW_IC_CON); + + /* Enable the adapter */ + dw_writel(dev, 1, DW_IC_ENABLE); + + /* Enable interrupts */ + dw_writel(dev, DW_IC_INTR_DEFAULT_MASK, DW_IC_INTR_MASK); +} + +/* + * Initiate (and continue) low level master read/write transaction. + * This function is only called from i2c_dw_isr, and pumping i2c_msg + * messages into the tx buffer. Even if the size of i2c_msg data is + * longer than the size of the tx buffer, it handles everything. + */ +void +i2c_dw_xfer_msg(struct dw_i2c_dev *dev) +{ + struct i2c_msg *msgs = dev->msgs; + u32 intr_mask; + int tx_limit, rx_limit; + u32 addr = msgs[dev->msg_write_idx].addr; + u32 buf_len = dev->tx_buf_len; + u8 *buf = dev->tx_buf; + + intr_mask = DW_IC_INTR_DEFAULT_MASK; + + for (; dev->msg_write_idx < dev->msgs_num; dev->msg_write_idx++) { + /* + * if target address has changed, we need to + * reprogram the target address in the i2c + * adapter when we are done with this transfer + */ + if (msgs[dev->msg_write_idx].addr != addr) { + dev_err(dev->dev, + "%s: invalid target address\n", __func__); + dev->msg_err = -EINVAL; + break; + } + + if (msgs[dev->msg_write_idx].len == 0) { + dev_err(dev->dev, + "%s: invalid message length\n", __func__); + dev->msg_err = -EINVAL; + break; + } + + if (!(dev->status & STATUS_WRITE_IN_PROGRESS)) { + /* new i2c_msg */ + buf = msgs[dev->msg_write_idx].buf; + buf_len = msgs[dev->msg_write_idx].len; + } + + tx_limit = dev->tx_fifo_depth - dw_readl(dev, DW_IC_TXFLR); + rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR); + + while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) { + if (msgs[dev->msg_write_idx].flags & I2C_M_RD) { + dw_writel(dev, 0x100, DW_IC_DATA_CMD); + rx_limit--; + } else + dw_writel(dev, *buf++, DW_IC_DATA_CMD); + tx_limit--; buf_len--; + } + + dev->tx_buf = buf; + dev->tx_buf_len = buf_len; + + if (buf_len > 0) { + /* more bytes to be written */ + dev->status |= STATUS_WRITE_IN_PROGRESS; + break; + } else + dev->status &= ~STATUS_WRITE_IN_PROGRESS; + } + + /* + * If i2c_msg index search is completed, we don't need TX_EMPTY + * interrupt any more. + */ + if (dev->msg_write_idx == dev->msgs_num) + intr_mask &= ~DW_IC_INTR_TX_EMPTY; + + if (dev->msg_err) + intr_mask = 0; + + dw_writel(dev, intr_mask, DW_IC_INTR_MASK); +} + +static void +i2c_dw_read(struct dw_i2c_dev *dev) +{ + struct i2c_msg *msgs = dev->msgs; + int rx_valid; + + for (; dev->msg_read_idx < dev->msgs_num; dev->msg_read_idx++) { + u32 len; + u8 *buf; + + if (!(msgs[dev->msg_read_idx].flags & I2C_M_RD)) + continue; + + if (!(dev->status & STATUS_READ_IN_PROGRESS)) { + len = msgs[dev->msg_read_idx].len; + buf = msgs[dev->msg_read_idx].buf; + } else { + len = dev->rx_buf_len; + buf = dev->rx_buf; + } + + rx_valid = dw_readl(dev, DW_IC_RXFLR); + + for (; len > 0 && rx_valid > 0; len--, rx_valid--) + *buf++ = dw_readl(dev, DW_IC_DATA_CMD); + + if (len > 0) { + dev->status |= STATUS_READ_IN_PROGRESS; + dev->rx_buf_len = len; + dev->rx_buf = buf; + return; + } else + dev->status &= ~STATUS_READ_IN_PROGRESS; + } +} + +static int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev) +{ + unsigned long abort_source = dev->abort_source; + int i; + + if (abort_source & DW_IC_TX_ABRT_NOACK) { + for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) + dev_dbg(dev->dev, + "%s: %s\n", __func__, abort_sources[i]); + return -EREMOTEIO; + } + + for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) + dev_err(dev->dev, "%s: %s\n", __func__, abort_sources[i]); + + if (abort_source & DW_IC_TX_ARB_LOST) + return -EAGAIN; + else if (abort_source & DW_IC_TX_ABRT_GCALL_READ) + return -EINVAL; /* wrong msgs[] data */ + else + return -EIO; +} + +/* + * Prepare controller for a transaction and call i2c_dw_xfer_msg + */ +int +i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) +{ + struct dw_i2c_dev *dev = i2c_get_adapdata(adap); + int ret; + + dev_dbg(dev->dev, "%s: msgs: %d\n", __func__, num); + + mutex_lock(&dev->lock); + + INIT_COMPLETION(dev->cmd_complete); + dev->msgs = msgs; + dev->msgs_num = num; + dev->cmd_err = 0; + dev->msg_write_idx = 0; + dev->msg_read_idx = 0; + dev->msg_err = 0; + dev->status = STATUS_IDLE; + dev->abort_source = 0; + + ret = i2c_dw_wait_bus_not_busy(dev); + if (ret < 0) + goto done; + + /* start the transfers */ + i2c_dw_xfer_init(dev); + + /* wait for tx to complete */ + ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete, HZ); + if (ret == 0) { + dev_err(dev->dev, "controller timed out\n"); + i2c_dw_init(dev); + ret = -ETIMEDOUT; + goto done; + } else if (ret < 0) + goto done; + + if (dev->msg_err) { + ret = dev->msg_err; + goto done; + } + + /* no error */ + if (likely(!dev->cmd_err)) { + /* Disable the adapter */ + dw_writel(dev, 0, DW_IC_ENABLE); + ret = num; + goto done; + } + + /* We have an error */ + if (dev->cmd_err == DW_IC_ERR_TX_ABRT) { + ret = i2c_dw_handle_tx_abort(dev); + goto done; + } + ret = -EIO; + +done: + mutex_unlock(&dev->lock); + + return ret; +} + +u32 i2c_dw_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | + I2C_FUNC_10BIT_ADDR | + I2C_FUNC_SMBUS_BYTE | + I2C_FUNC_SMBUS_BYTE_DATA | + I2C_FUNC_SMBUS_WORD_DATA | + I2C_FUNC_SMBUS_I2C_BLOCK; +} + +static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev) +{ + u32 stat; + + /* + * The IC_INTR_STAT register just indicates "enabled" interrupts. + * Ths unmasked raw version of interrupt status bits are available + * in the IC_RAW_INTR_STAT register. + * + * That is, + * stat = dw_readl(IC_INTR_STAT); + * equals to, + * stat = dw_readl(IC_RAW_INTR_STAT) & dw_readl(IC_INTR_MASK); + * + * The raw version might be useful for debugging purposes. + */ + stat = dw_readl(dev, DW_IC_INTR_STAT); + + /* + * Do not use the IC_CLR_INTR register to clear interrupts, or + * you'll miss some interrupts, triggered during the period from + * dw_readl(IC_INTR_STAT) to dw_readl(IC_CLR_INTR). + * + * Instead, use the separately-prepared IC_CLR_* registers. + */ + if (stat & DW_IC_INTR_RX_UNDER) + dw_readl(dev, DW_IC_CLR_RX_UNDER); + if (stat & DW_IC_INTR_RX_OVER) + dw_readl(dev, DW_IC_CLR_RX_OVER); + if (stat & DW_IC_INTR_TX_OVER) + dw_readl(dev, DW_IC_CLR_TX_OVER); + if (stat & DW_IC_INTR_RD_REQ) + dw_readl(dev, DW_IC_CLR_RD_REQ); + if (stat & DW_IC_INTR_TX_ABRT) { + /* + * The IC_TX_ABRT_SOURCE register is cleared whenever + * the IC_CLR_TX_ABRT is read. Preserve it beforehand. + */ + dev->abort_source = dw_readl(dev, DW_IC_TX_ABRT_SOURCE); + dw_readl(dev, DW_IC_CLR_TX_ABRT); + } + if (stat & DW_IC_INTR_RX_DONE) + dw_readl(dev, DW_IC_CLR_RX_DONE); + if (stat & DW_IC_INTR_ACTIVITY) + dw_readl(dev, DW_IC_CLR_ACTIVITY); + if (stat & DW_IC_INTR_STOP_DET) + dw_readl(dev, DW_IC_CLR_STOP_DET); + if (stat & DW_IC_INTR_START_DET) + dw_readl(dev, DW_IC_CLR_START_DET); + if (stat & DW_IC_INTR_GEN_CALL) + dw_readl(dev, DW_IC_CLR_GEN_CALL); + + return stat; +} + +/* + * Interrupt service routine. This gets called whenever an I2C interrupt + * occurs. + */ +irqreturn_t i2c_dw_isr(int this_irq, void *dev_id) +{ + struct dw_i2c_dev *dev = dev_id; + u32 stat; + + stat = i2c_dw_read_clear_intrbits(dev); + dev_dbg(dev->dev, "%s: stat=0x%x\n", __func__, stat); + + if (stat & DW_IC_INTR_TX_ABRT) { + dev->cmd_err |= DW_IC_ERR_TX_ABRT; + dev->status = STATUS_IDLE; + + /* + * Anytime TX_ABRT is set, the contents of the tx/rx + * buffers are flushed. Make sure to skip them. + */ + dw_writel(dev, 0, DW_IC_INTR_MASK); + goto tx_aborted; + } + + if (stat & DW_IC_INTR_RX_FULL) + i2c_dw_read(dev); + + if (stat & DW_IC_INTR_TX_EMPTY) + i2c_dw_xfer_msg(dev); + + /* + * No need to modify or disable the interrupt mask here. + * i2c_dw_xfer_msg() will take care of it according to + * the current transmit status. + */ + +tx_aborted: + if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) || dev->msg_err) + complete(&dev->cmd_complete); + + return IRQ_HANDLED; +} diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h new file mode 100644 index 0000000..4e37031 --- /dev/null +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -0,0 +1,194 @@ +/* + * Synopsys DesignWare I2C adapter driver (master only). + * + * Based on the TI DAVINCI I2C adapter driver. + * + * Copyright (C) 2006 Texas Instruments. + * Copyright (C) 2007 MontaVista Software Inc. + * Copyright (C) 2009 Provigent Ltd. + * + * ---------------------------------------------------------------------------- + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + * + */ + +/* + * Registers offset + */ +#define DW_IC_CON 0x0 +#define DW_IC_TAR 0x4 +#define DW_IC_DATA_CMD 0x10 +#define DW_IC_SS_SCL_HCNT 0x14 +#define DW_IC_SS_SCL_LCNT 0x18 +#define DW_IC_FS_SCL_HCNT 0x1c +#define DW_IC_FS_SCL_LCNT 0x20 +#define DW_IC_INTR_STAT 0x2c +#define DW_IC_INTR_MASK 0x30 +#define DW_IC_RAW_INTR_STAT 0x34 +#define DW_IC_RX_TL 0x38 +#define DW_IC_TX_TL 0x3c +#define DW_IC_CLR_INTR 0x40 +#define DW_IC_CLR_RX_UNDER 0x44 +#define DW_IC_CLR_RX_OVER 0x48 +#define DW_IC_CLR_TX_OVER 0x4c +#define DW_IC_CLR_RD_REQ 0x50 +#define DW_IC_CLR_TX_ABRT 0x54 +#define DW_IC_CLR_RX_DONE 0x58 +#define DW_IC_CLR_ACTIVITY 0x5c +#define DW_IC_CLR_STOP_DET 0x60 +#define DW_IC_CLR_START_DET 0x64 +#define DW_IC_CLR_GEN_CALL 0x68 +#define DW_IC_ENABLE 0x6c +#define DW_IC_STATUS 0x70 +#define DW_IC_TXFLR 0x74 +#define DW_IC_RXFLR 0x78 +#define DW_IC_TX_ABRT_SOURCE 0x80 +#define DW_IC_COMP_PARAM_1 0xf4 +#define DW_IC_COMP_TYPE 0xfc +#define DW_IC_COMP_TYPE_VALUE 0x44570140 + +#define DW_IC_CON_MASTER 0x1 +#define DW_IC_CON_SPEED_STD 0x2 +#define DW_IC_CON_SPEED_FAST 0x4 +#define DW_IC_CON_10BITADDR_MASTER 0x10 +#define DW_IC_CON_RESTART_EN 0x20 +#define DW_IC_CON_SLAVE_DISABLE 0x40 + +#define DW_IC_INTR_RX_UNDER 0x001 +#define DW_IC_INTR_RX_OVER 0x002 +#define DW_IC_INTR_RX_FULL 0x004 +#define DW_IC_INTR_TX_OVER 0x008 +#define DW_IC_INTR_TX_EMPTY 0x010 +#define DW_IC_INTR_RD_REQ 0x020 +#define DW_IC_INTR_TX_ABRT 0x040 +#define DW_IC_INTR_RX_DONE 0x080 +#define DW_IC_INTR_ACTIVITY 0x100 +#define DW_IC_INTR_STOP_DET 0x200 +#define DW_IC_INTR_START_DET 0x400 +#define DW_IC_INTR_GEN_CALL 0x800 + +#define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \ + DW_IC_INTR_TX_EMPTY | \ + DW_IC_INTR_TX_ABRT | \ + DW_IC_INTR_STOP_DET) + +#define DW_IC_STATUS_ACTIVITY 0x1 + +#define DW_IC_ERR_TX_ABRT 0x1 + +/* + * status codes + */ +#define STATUS_IDLE 0x0 +#define STATUS_WRITE_IN_PROGRESS 0x1 +#define STATUS_READ_IN_PROGRESS 0x2 + +#define TIMEOUT 20 /* ms */ + +/* + * hardware abort codes from the DW_IC_TX_ABRT_SOURCE register + * + * only expected abort codes are listed here + * refer to the datasheet for the full list + */ +#define ABRT_7B_ADDR_NOACK 0 +#define ABRT_10ADDR1_NOACK 1 +#define ABRT_10ADDR2_NOACK 2 +#define ABRT_TXDATA_NOACK 3 +#define ABRT_GCALL_NOACK 4 +#define ABRT_GCALL_READ 5 +#define ABRT_SBYTE_ACKDET 7 +#define ABRT_SBYTE_NORSTRT 9 +#define ABRT_10B_RD_NORSTRT 10 +#define ABRT_MASTER_DIS 11 +#define ARB_LOST 12 + +#define DW_IC_TX_ABRT_7B_ADDR_NOACK (1UL << ABRT_7B_ADDR_NOACK) +#define DW_IC_TX_ABRT_10ADDR1_NOACK (1UL << ABRT_10ADDR1_NOACK) +#define DW_IC_TX_ABRT_10ADDR2_NOACK (1UL << ABRT_10ADDR2_NOACK) +#define DW_IC_TX_ABRT_TXDATA_NOACK (1UL << ABRT_TXDATA_NOACK) +#define DW_IC_TX_ABRT_GCALL_NOACK (1UL << ABRT_GCALL_NOACK) +#define DW_IC_TX_ABRT_GCALL_READ (1UL << ABRT_GCALL_READ) +#define DW_IC_TX_ABRT_SBYTE_ACKDET (1UL << ABRT_SBYTE_ACKDET) +#define DW_IC_TX_ABRT_SBYTE_NORSTRT (1UL << ABRT_SBYTE_NORSTRT) +#define DW_IC_TX_ABRT_10B_RD_NORSTRT (1UL << ABRT_10B_RD_NORSTRT) +#define DW_IC_TX_ABRT_MASTER_DIS (1UL << ABRT_MASTER_DIS) +#define DW_IC_TX_ARB_LOST (1UL << ARB_LOST) + +#define DW_IC_TX_ABRT_NOACK (DW_IC_TX_ABRT_7B_ADDR_NOACK | \ + DW_IC_TX_ABRT_10ADDR1_NOACK | \ + DW_IC_TX_ABRT_10ADDR2_NOACK | \ + DW_IC_TX_ABRT_TXDATA_NOACK | \ + DW_IC_TX_ABRT_GCALL_NOACK) +/** + * struct dw_i2c_dev - private i2c-designware data + * @dev: driver model device node + * @base: IO registers pointer + * @cmd_complete: tx completion indicator + * @lock: protect this struct and IO registers + * @clk: input reference clock + * @cmd_err: run time hadware error code + * @msgs: points to an array of messages currently being transfered + * @msgs_num: the number of elements in msgs + * @msg_write_idx: the element index of the current tx message in the msgs + * array + * @tx_buf_len: the length of the current tx buffer + * @tx_buf: the current tx buffer + * @msg_read_idx: the element index of the current rx message in the msgs + * array + * @rx_buf_len: the length of the current rx buffer + * @rx_buf: the current rx buffer + * @msg_err: error status of the current transfer + * @status: i2c master status, one of STATUS_* + * @abort_source: copy of the TX_ABRT_SOURCE register + * @irq: interrupt number for the i2c master + * @adapter: i2c subsystem adapter node + * @tx_fifo_depth: depth of the hardware tx fifo + * @rx_fifo_depth: depth of the hardware rx fifo + */ +struct dw_i2c_dev { + struct device *dev; + void __iomem *base; + struct completion cmd_complete; + struct mutex lock; + struct clk *clk; + int cmd_err; + struct i2c_msg *msgs; + int msgs_num; + int msg_write_idx; + u32 tx_buf_len; + u8 *tx_buf; + int msg_read_idx; + u32 rx_buf_len; + u8 *rx_buf; + int msg_err; + unsigned int status; + u32 abort_source; + int irq; + int swab; + struct i2c_adapter adapter; + unsigned int tx_fifo_depth; + unsigned int rx_fifo_depth; +}; + +extern u32 dw_readl(struct dw_i2c_dev *dev, int offset); +extern void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset); +extern int i2c_dw_init(struct dw_i2c_dev *dev); +extern int i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], + int num); +extern u32 i2c_dw_func(struct i2c_adapter *adap); +extern irqreturn_t i2c_dw_isr(int this_irq, void *dev_id); diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c new file mode 100644 index 0000000..9d10ae8 --- /dev/null +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -0,0 +1,199 @@ +/* + * Synopsys DesignWare I2C adapter driver (master only). + * + * Based on the TI DAVINCI I2C adapter driver. + * + * Copyright (C) 2006 Texas Instruments. + * Copyright (C) 2007 MontaVista Software Inc. + * Copyright (C) 2009 Provigent Ltd. + * + * ---------------------------------------------------------------------------- + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "i2c-designware-core.h" + +static struct i2c_algorithm i2c_dw_algo = { + .master_xfer = i2c_dw_xfer, + .functionality = i2c_dw_func, +}; + +static int __devinit dw_i2c_probe(struct platform_device *pdev) +{ + struct dw_i2c_dev *dev; + struct i2c_adapter *adap; + struct resource *mem, *ioarea; + int irq, r; + + /* NOTE: driver uses the static register mapping */ + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!mem) { + dev_err(&pdev->dev, "no mem resource?\n"); + return -EINVAL; + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "no irq resource?\n"); + return irq; /* -ENXIO */ + } + + ioarea = request_mem_region(mem->start, resource_size(mem), + pdev->name); + if (!ioarea) { + dev_err(&pdev->dev, "I2C region already claimed\n"); + return -EBUSY; + } + + dev = kzalloc(sizeof(struct dw_i2c_dev), GFP_KERNEL); + if (!dev) { + r = -ENOMEM; + goto err_release_region; + } + + init_completion(&dev->cmd_complete); + mutex_init(&dev->lock); + dev->dev = get_device(&pdev->dev); + dev->irq = irq; + platform_set_drvdata(pdev, dev); + + dev->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(dev->clk)) { + r = -ENODEV; + goto err_free_mem; + } + clk_enable(dev->clk); + + dev->base = ioremap(mem->start, resource_size(mem)); + if (dev->base == NULL) { + dev_err(&pdev->dev, "failure mapping io resources\n"); + r = -EBUSY; + goto err_unuse_clocks; + } + { + u32 param1 = dw_readl(dev, DW_IC_COMP_PARAM_1); + + dev->tx_fifo_depth = ((param1 >> 16) & 0xff) + 1; + dev->rx_fifo_depth = ((param1 >> 8) & 0xff) + 1; + } + r = i2c_dw_init(dev); + if (r) + goto err_iounmap; + + dw_writel(dev, 0, DW_IC_INTR_MASK); /* disable IRQ */ + r = request_irq(dev->irq, i2c_dw_isr, IRQF_DISABLED, pdev->name, dev); + if (r) { + dev_err(&pdev->dev, "failure requesting irq %i\n", dev->irq); + goto err_iounmap; + } + + adap = &dev->adapter; + i2c_set_adapdata(adap, dev); + adap->owner = THIS_MODULE; + adap->class = I2C_CLASS_HWMON; + strlcpy(adap->name, "Synopsys DesignWare I2C adapter", + sizeof(adap->name)); + adap->algo = &i2c_dw_algo; + adap->dev.parent = &pdev->dev; + + adap->nr = pdev->id; + r = i2c_add_numbered_adapter(adap); + if (r) { + dev_err(&pdev->dev, "failure adding adapter\n"); + goto err_free_irq; + } + + return 0; + +err_free_irq: + free_irq(dev->irq, dev); +err_iounmap: + iounmap(dev->base); +err_unuse_clocks: + clk_disable(dev->clk); + clk_put(dev->clk); + dev->clk = NULL; +err_free_mem: + platform_set_drvdata(pdev, NULL); + put_device(&pdev->dev); + kfree(dev); +err_release_region: + release_mem_region(mem->start, resource_size(mem)); + + return r; +} + +static int __devexit dw_i2c_remove(struct platform_device *pdev) +{ + struct dw_i2c_dev *dev = platform_get_drvdata(pdev); + struct resource *mem; + + platform_set_drvdata(pdev, NULL); + i2c_del_adapter(&dev->adapter); + put_device(&pdev->dev); + + clk_disable(dev->clk); + clk_put(dev->clk); + dev->clk = NULL; + + dw_writel(dev, 0, DW_IC_ENABLE); + free_irq(dev->irq, dev); + kfree(dev); + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(mem->start, resource_size(mem)); + return 0; +} + +/* work with hotplug and coldplug */ +MODULE_ALIAS("platform:i2c_designware"); + +static struct platform_driver dw_i2c_driver = { + .remove = __devexit_p(dw_i2c_remove), + .driver = { + .name = "i2c_designware", + .owner = THIS_MODULE, + }, +}; + +static int __init dw_i2c_init_driver(void) +{ + return platform_driver_probe(&dw_i2c_driver, dw_i2c_probe); +} +module_init(dw_i2c_init_driver); + +static void __exit dw_i2c_exit_driver(void) +{ + platform_driver_unregister(&dw_i2c_driver); +} +module_exit(dw_i2c_exit_driver); + +MODULE_AUTHOR("Baruch Siach "); +MODULE_DESCRIPTION("Synopsys DesignWare I2C bus adapter"); +MODULE_LICENSE("GPL"); diff --git a/drivers/i2c/busses/i2c-designware.c b/drivers/i2c/busses/i2c-designware.c deleted file mode 100644 index a7abbcd..0000000 --- a/drivers/i2c/busses/i2c-designware.c +++ /dev/null @@ -1,887 +0,0 @@ -/* - * Synopsys DesignWare I2C adapter driver (master only). - * - * Based on the TI DAVINCI I2C adapter driver. - * - * Copyright (C) 2006 Texas Instruments. - * Copyright (C) 2007 MontaVista Software Inc. - * Copyright (C) 2009 Provigent Ltd. - * - * ---------------------------------------------------------------------------- - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * ---------------------------------------------------------------------------- - * - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -/* - * Registers offset - */ -#define DW_IC_CON 0x0 -#define DW_IC_TAR 0x4 -#define DW_IC_DATA_CMD 0x10 -#define DW_IC_SS_SCL_HCNT 0x14 -#define DW_IC_SS_SCL_LCNT 0x18 -#define DW_IC_FS_SCL_HCNT 0x1c -#define DW_IC_FS_SCL_LCNT 0x20 -#define DW_IC_INTR_STAT 0x2c -#define DW_IC_INTR_MASK 0x30 -#define DW_IC_RAW_INTR_STAT 0x34 -#define DW_IC_RX_TL 0x38 -#define DW_IC_TX_TL 0x3c -#define DW_IC_CLR_INTR 0x40 -#define DW_IC_CLR_RX_UNDER 0x44 -#define DW_IC_CLR_RX_OVER 0x48 -#define DW_IC_CLR_TX_OVER 0x4c -#define DW_IC_CLR_RD_REQ 0x50 -#define DW_IC_CLR_TX_ABRT 0x54 -#define DW_IC_CLR_RX_DONE 0x58 -#define DW_IC_CLR_ACTIVITY 0x5c -#define DW_IC_CLR_STOP_DET 0x60 -#define DW_IC_CLR_START_DET 0x64 -#define DW_IC_CLR_GEN_CALL 0x68 -#define DW_IC_ENABLE 0x6c -#define DW_IC_STATUS 0x70 -#define DW_IC_TXFLR 0x74 -#define DW_IC_RXFLR 0x78 -#define DW_IC_COMP_PARAM_1 0xf4 -#define DW_IC_COMP_TYPE 0xfc -#define DW_IC_TX_ABRT_SOURCE 0x80 - -#define DW_IC_CON_MASTER 0x1 -#define DW_IC_CON_SPEED_STD 0x2 -#define DW_IC_CON_SPEED_FAST 0x4 -#define DW_IC_CON_10BITADDR_MASTER 0x10 -#define DW_IC_CON_RESTART_EN 0x20 -#define DW_IC_CON_SLAVE_DISABLE 0x40 - -#define DW_IC_INTR_RX_UNDER 0x001 -#define DW_IC_INTR_RX_OVER 0x002 -#define DW_IC_INTR_RX_FULL 0x004 -#define DW_IC_INTR_TX_OVER 0x008 -#define DW_IC_INTR_TX_EMPTY 0x010 -#define DW_IC_INTR_RD_REQ 0x020 -#define DW_IC_INTR_TX_ABRT 0x040 -#define DW_IC_INTR_RX_DONE 0x080 -#define DW_IC_INTR_ACTIVITY 0x100 -#define DW_IC_INTR_STOP_DET 0x200 -#define DW_IC_INTR_START_DET 0x400 -#define DW_IC_INTR_GEN_CALL 0x800 - -#define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \ - DW_IC_INTR_TX_EMPTY | \ - DW_IC_INTR_TX_ABRT | \ - DW_IC_INTR_STOP_DET) - -#define DW_IC_STATUS_ACTIVITY 0x1 - -#define DW_IC_ERR_TX_ABRT 0x1 - -/* - * status codes - */ -#define STATUS_IDLE 0x0 -#define STATUS_WRITE_IN_PROGRESS 0x1 -#define STATUS_READ_IN_PROGRESS 0x2 - -#define TIMEOUT 20 /* ms */ - -/* - * hardware abort codes from the DW_IC_TX_ABRT_SOURCE register - * - * only expected abort codes are listed here - * refer to the datasheet for the full list - */ -#define ABRT_7B_ADDR_NOACK 0 -#define ABRT_10ADDR1_NOACK 1 -#define ABRT_10ADDR2_NOACK 2 -#define ABRT_TXDATA_NOACK 3 -#define ABRT_GCALL_NOACK 4 -#define ABRT_GCALL_READ 5 -#define ABRT_SBYTE_ACKDET 7 -#define ABRT_SBYTE_NORSTRT 9 -#define ABRT_10B_RD_NORSTRT 10 -#define ABRT_MASTER_DIS 11 -#define ARB_LOST 12 - -#define DW_IC_TX_ABRT_7B_ADDR_NOACK (1UL << ABRT_7B_ADDR_NOACK) -#define DW_IC_TX_ABRT_10ADDR1_NOACK (1UL << ABRT_10ADDR1_NOACK) -#define DW_IC_TX_ABRT_10ADDR2_NOACK (1UL << ABRT_10ADDR2_NOACK) -#define DW_IC_TX_ABRT_TXDATA_NOACK (1UL << ABRT_TXDATA_NOACK) -#define DW_IC_TX_ABRT_GCALL_NOACK (1UL << ABRT_GCALL_NOACK) -#define DW_IC_TX_ABRT_GCALL_READ (1UL << ABRT_GCALL_READ) -#define DW_IC_TX_ABRT_SBYTE_ACKDET (1UL << ABRT_SBYTE_ACKDET) -#define DW_IC_TX_ABRT_SBYTE_NORSTRT (1UL << ABRT_SBYTE_NORSTRT) -#define DW_IC_TX_ABRT_10B_RD_NORSTRT (1UL << ABRT_10B_RD_NORSTRT) -#define DW_IC_TX_ABRT_MASTER_DIS (1UL << ABRT_MASTER_DIS) -#define DW_IC_TX_ARB_LOST (1UL << ARB_LOST) - -#define DW_IC_TX_ABRT_NOACK (DW_IC_TX_ABRT_7B_ADDR_NOACK | \ - DW_IC_TX_ABRT_10ADDR1_NOACK | \ - DW_IC_TX_ABRT_10ADDR2_NOACK | \ - DW_IC_TX_ABRT_TXDATA_NOACK | \ - DW_IC_TX_ABRT_GCALL_NOACK) - -static char *abort_sources[] = { - [ABRT_7B_ADDR_NOACK] = - "slave address not acknowledged (7bit mode)", - [ABRT_10ADDR1_NOACK] = - "first address byte not acknowledged (10bit mode)", - [ABRT_10ADDR2_NOACK] = - "second address byte not acknowledged (10bit mode)", - [ABRT_TXDATA_NOACK] = - "data not acknowledged", - [ABRT_GCALL_NOACK] = - "no acknowledgement for a general call", - [ABRT_GCALL_READ] = - "read after general call", - [ABRT_SBYTE_ACKDET] = - "start byte acknowledged", - [ABRT_SBYTE_NORSTRT] = - "trying to send start byte when restart is disabled", - [ABRT_10B_RD_NORSTRT] = - "trying to read when restart is disabled (10bit mode)", - [ABRT_MASTER_DIS] = - "trying to use disabled adapter", - [ARB_LOST] = - "lost arbitration", -}; - -/** - * struct dw_i2c_dev - private i2c-designware data - * @dev: driver model device node - * @base: IO registers pointer - * @cmd_complete: tx completion indicator - * @lock: protect this struct and IO registers - * @clk: input reference clock - * @cmd_err: run time hadware error code - * @msgs: points to an array of messages currently being transferred - * @msgs_num: the number of elements in msgs - * @msg_write_idx: the element index of the current tx message in the msgs - * array - * @tx_buf_len: the length of the current tx buffer - * @tx_buf: the current tx buffer - * @msg_read_idx: the element index of the current rx message in the msgs - * array - * @rx_buf_len: the length of the current rx buffer - * @rx_buf: the current rx buffer - * @msg_err: error status of the current transfer - * @status: i2c master status, one of STATUS_* - * @abort_source: copy of the TX_ABRT_SOURCE register - * @irq: interrupt number for the i2c master - * @swab: true if the instantiated IP is of different endianess - * @adapter: i2c subsystem adapter node - * @tx_fifo_depth: depth of the hardware tx fifo - * @rx_fifo_depth: depth of the hardware rx fifo - */ -struct dw_i2c_dev { - struct device *dev; - void __iomem *base; - struct completion cmd_complete; - struct mutex lock; - struct clk *clk; - int cmd_err; - struct i2c_msg *msgs; - int msgs_num; - int msg_write_idx; - u32 tx_buf_len; - u8 *tx_buf; - int msg_read_idx; - u32 rx_buf_len; - u8 *rx_buf; - int msg_err; - unsigned int status; - u32 abort_source; - int irq; - int swab; - struct i2c_adapter adapter; - unsigned int tx_fifo_depth; - unsigned int rx_fifo_depth; -}; - -static u32 dw_readl(struct dw_i2c_dev *dev, int offset) -{ - u32 value = readl(dev->base + offset); - - if (dev->swab) - return swab32(value); - else - return value; -} - -static void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset) -{ - if (dev->swab) - b = swab32(b); - - writel(b, dev->base + offset); -} - -static u32 -i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset) -{ - /* - * DesignWare I2C core doesn't seem to have solid strategy to meet - * the tHD;STA timing spec. Configuring _HCNT based on tHIGH spec - * will result in violation of the tHD;STA spec. - */ - if (cond) - /* - * Conditional expression: - * - * IC_[FS]S_SCL_HCNT + (1+4+3) >= IC_CLK * tHIGH - * - * This is based on the DW manuals, and represents an ideal - * configuration. The resulting I2C bus speed will be - * faster than any of the others. - * - * If your hardware is free from tHD;STA issue, try this one. - */ - return (ic_clk * tSYMBOL + 5000) / 10000 - 8 + offset; - else - /* - * Conditional expression: - * - * IC_[FS]S_SCL_HCNT + 3 >= IC_CLK * (tHD;STA + tf) - * - * This is just experimental rule; the tHD;STA period turned - * out to be proportinal to (_HCNT + 3). With this setting, - * we could meet both tHIGH and tHD;STA timing specs. - * - * If unsure, you'd better to take this alternative. - * - * The reason why we need to take into account "tf" here, - * is the same as described in i2c_dw_scl_lcnt(). - */ - return (ic_clk * (tSYMBOL + tf) + 5000) / 10000 - 3 + offset; -} - -static u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset) -{ - /* - * Conditional expression: - * - * IC_[FS]S_SCL_LCNT + 1 >= IC_CLK * (tLOW + tf) - * - * DW I2C core starts counting the SCL CNTs for the LOW period - * of the SCL clock (tLOW) as soon as it pulls the SCL line. - * In order to meet the tLOW timing spec, we need to take into - * account the fall time of SCL signal (tf). Default tf value - * should be 0.3 us, for safety. - */ - return ((ic_clk * (tLOW + tf) + 5000) / 10000) - 1 + offset; -} - -/** - * i2c_dw_init() - initialize the designware i2c master hardware - * @dev: device private data - * - * This functions configures and enables the I2C master. - * This function is called during I2C init function, and in case of timeout at - * run time. - */ -static int i2c_dw_init(struct dw_i2c_dev *dev) -{ - u32 input_clock_khz = clk_get_rate(dev->clk) / 1000; - u32 ic_con, hcnt, lcnt; - u32 reg; - - /* Configure register endianess access */ - reg = dw_readl(dev, DW_IC_COMP_TYPE); - if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) { - dev->swab = 1; - reg = DW_IC_COMP_TYPE_VALUE; - } - - if (reg != DW_IC_COMP_TYPE_VALUE) { - dev_err(dev->dev, "Unknown Synopsys component type: " - "0x%08x\n", reg); - return -ENODEV; - } - - /* Disable the adapter */ - dw_writel(dev, 0, DW_IC_ENABLE); - - /* set standard and fast speed deviders for high/low periods */ - - /* Standard-mode */ - hcnt = i2c_dw_scl_hcnt(input_clock_khz, - 40, /* tHD;STA = tHIGH = 4.0 us */ - 3, /* tf = 0.3 us */ - 0, /* 0: DW default, 1: Ideal */ - 0); /* No offset */ - lcnt = i2c_dw_scl_lcnt(input_clock_khz, - 47, /* tLOW = 4.7 us */ - 3, /* tf = 0.3 us */ - 0); /* No offset */ - dw_writel(dev, hcnt, DW_IC_SS_SCL_HCNT); - dw_writel(dev, lcnt, DW_IC_SS_SCL_LCNT); - dev_dbg(dev->dev, "Standard-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt); - - /* Fast-mode */ - hcnt = i2c_dw_scl_hcnt(input_clock_khz, - 6, /* tHD;STA = tHIGH = 0.6 us */ - 3, /* tf = 0.3 us */ - 0, /* 0: DW default, 1: Ideal */ - 0); /* No offset */ - lcnt = i2c_dw_scl_lcnt(input_clock_khz, - 13, /* tLOW = 1.3 us */ - 3, /* tf = 0.3 us */ - 0); /* No offset */ - dw_writel(dev, hcnt, DW_IC_FS_SCL_HCNT); - dw_writel(dev, lcnt, DW_IC_FS_SCL_LCNT); - dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt); - - /* Configure Tx/Rx FIFO threshold levels */ - dw_writel(dev, dev->tx_fifo_depth - 1, DW_IC_TX_TL); - dw_writel(dev, 0, DW_IC_RX_TL); - - /* configure the i2c master */ - ic_con = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE | - DW_IC_CON_RESTART_EN | DW_IC_CON_SPEED_FAST; - dw_writel(dev, ic_con, DW_IC_CON); - return 0; -} - -/* - * Waiting for bus not busy - */ -static int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev) -{ - int timeout = TIMEOUT; - - while (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) { - if (timeout <= 0) { - dev_warn(dev->dev, "timeout waiting for bus ready\n"); - return -ETIMEDOUT; - } - timeout--; - mdelay(1); - } - - return 0; -} - -static void i2c_dw_xfer_init(struct dw_i2c_dev *dev) -{ - struct i2c_msg *msgs = dev->msgs; - u32 ic_con; - - /* Disable the adapter */ - dw_writel(dev, 0, DW_IC_ENABLE); - - /* set the slave (target) address */ - dw_writel(dev, msgs[dev->msg_write_idx].addr, DW_IC_TAR); - - /* if the slave address is ten bit address, enable 10BITADDR */ - ic_con = dw_readl(dev, DW_IC_CON); - if (msgs[dev->msg_write_idx].flags & I2C_M_TEN) - ic_con |= DW_IC_CON_10BITADDR_MASTER; - else - ic_con &= ~DW_IC_CON_10BITADDR_MASTER; - dw_writel(dev, ic_con, DW_IC_CON); - - /* Enable the adapter */ - dw_writel(dev, 1, DW_IC_ENABLE); - - /* Enable interrupts */ - dw_writel(dev, DW_IC_INTR_DEFAULT_MASK, DW_IC_INTR_MASK); -} - -/* - * Initiate (and continue) low level master read/write transaction. - * This function is only called from i2c_dw_isr, and pumping i2c_msg - * messages into the tx buffer. Even if the size of i2c_msg data is - * longer than the size of the tx buffer, it handles everything. - */ -static void -i2c_dw_xfer_msg(struct dw_i2c_dev *dev) -{ - struct i2c_msg *msgs = dev->msgs; - u32 intr_mask; - int tx_limit, rx_limit; - u32 addr = msgs[dev->msg_write_idx].addr; - u32 buf_len = dev->tx_buf_len; - u8 *buf = dev->tx_buf; - - intr_mask = DW_IC_INTR_DEFAULT_MASK; - - for (; dev->msg_write_idx < dev->msgs_num; dev->msg_write_idx++) { - /* - * if target address has changed, we need to - * reprogram the target address in the i2c - * adapter when we are done with this transfer - */ - if (msgs[dev->msg_write_idx].addr != addr) { - dev_err(dev->dev, - "%s: invalid target address\n", __func__); - dev->msg_err = -EINVAL; - break; - } - - if (msgs[dev->msg_write_idx].len == 0) { - dev_err(dev->dev, - "%s: invalid message length\n", __func__); - dev->msg_err = -EINVAL; - break; - } - - if (!(dev->status & STATUS_WRITE_IN_PROGRESS)) { - /* new i2c_msg */ - buf = msgs[dev->msg_write_idx].buf; - buf_len = msgs[dev->msg_write_idx].len; - } - - tx_limit = dev->tx_fifo_depth - dw_readl(dev, DW_IC_TXFLR); - rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR); - - while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) { - if (msgs[dev->msg_write_idx].flags & I2C_M_RD) { - dw_writel(dev, 0x100, DW_IC_DATA_CMD); - rx_limit--; - } else - dw_writel(dev, *buf++, DW_IC_DATA_CMD); - tx_limit--; buf_len--; - } - - dev->tx_buf = buf; - dev->tx_buf_len = buf_len; - - if (buf_len > 0) { - /* more bytes to be written */ - dev->status |= STATUS_WRITE_IN_PROGRESS; - break; - } else - dev->status &= ~STATUS_WRITE_IN_PROGRESS; - } - - /* - * If i2c_msg index search is completed, we don't need TX_EMPTY - * interrupt any more. - */ - if (dev->msg_write_idx == dev->msgs_num) - intr_mask &= ~DW_IC_INTR_TX_EMPTY; - - if (dev->msg_err) - intr_mask = 0; - - dw_writel(dev, intr_mask, DW_IC_INTR_MASK); -} - -static void -i2c_dw_read(struct dw_i2c_dev *dev) -{ - struct i2c_msg *msgs = dev->msgs; - int rx_valid; - - for (; dev->msg_read_idx < dev->msgs_num; dev->msg_read_idx++) { - u32 len; - u8 *buf; - - if (!(msgs[dev->msg_read_idx].flags & I2C_M_RD)) - continue; - - if (!(dev->status & STATUS_READ_IN_PROGRESS)) { - len = msgs[dev->msg_read_idx].len; - buf = msgs[dev->msg_read_idx].buf; - } else { - len = dev->rx_buf_len; - buf = dev->rx_buf; - } - - rx_valid = dw_readl(dev, DW_IC_RXFLR); - - for (; len > 0 && rx_valid > 0; len--, rx_valid--) - *buf++ = dw_readl(dev, DW_IC_DATA_CMD); - - if (len > 0) { - dev->status |= STATUS_READ_IN_PROGRESS; - dev->rx_buf_len = len; - dev->rx_buf = buf; - return; - } else - dev->status &= ~STATUS_READ_IN_PROGRESS; - } -} - -static int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev) -{ - unsigned long abort_source = dev->abort_source; - int i; - - if (abort_source & DW_IC_TX_ABRT_NOACK) { - for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) - dev_dbg(dev->dev, - "%s: %s\n", __func__, abort_sources[i]); - return -EREMOTEIO; - } - - for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources)) - dev_err(dev->dev, "%s: %s\n", __func__, abort_sources[i]); - - if (abort_source & DW_IC_TX_ARB_LOST) - return -EAGAIN; - else if (abort_source & DW_IC_TX_ABRT_GCALL_READ) - return -EINVAL; /* wrong msgs[] data */ - else - return -EIO; -} - -/* - * Prepare controller for a transaction and call i2c_dw_xfer_msg - */ -static int -i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) -{ - struct dw_i2c_dev *dev = i2c_get_adapdata(adap); - int ret; - - dev_dbg(dev->dev, "%s: msgs: %d\n", __func__, num); - - mutex_lock(&dev->lock); - - INIT_COMPLETION(dev->cmd_complete); - dev->msgs = msgs; - dev->msgs_num = num; - dev->cmd_err = 0; - dev->msg_write_idx = 0; - dev->msg_read_idx = 0; - dev->msg_err = 0; - dev->status = STATUS_IDLE; - dev->abort_source = 0; - - ret = i2c_dw_wait_bus_not_busy(dev); - if (ret < 0) - goto done; - - /* start the transfers */ - i2c_dw_xfer_init(dev); - - /* wait for tx to complete */ - ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete, HZ); - if (ret == 0) { - dev_err(dev->dev, "controller timed out\n"); - i2c_dw_init(dev); - ret = -ETIMEDOUT; - goto done; - } else if (ret < 0) - goto done; - - if (dev->msg_err) { - ret = dev->msg_err; - goto done; - } - - /* no error */ - if (likely(!dev->cmd_err)) { - /* Disable the adapter */ - dw_writel(dev, 0, DW_IC_ENABLE); - ret = num; - goto done; - } - - /* We have an error */ - if (dev->cmd_err == DW_IC_ERR_TX_ABRT) { - ret = i2c_dw_handle_tx_abort(dev); - goto done; - } - ret = -EIO; - -done: - mutex_unlock(&dev->lock); - - return ret; -} - -static u32 i2c_dw_func(struct i2c_adapter *adap) -{ - return I2C_FUNC_I2C | - I2C_FUNC_10BIT_ADDR | - I2C_FUNC_SMBUS_BYTE | - I2C_FUNC_SMBUS_BYTE_DATA | - I2C_FUNC_SMBUS_WORD_DATA | - I2C_FUNC_SMBUS_I2C_BLOCK; -} - -static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev) -{ - u32 stat; - - /* - * The IC_INTR_STAT register just indicates "enabled" interrupts. - * Ths unmasked raw version of interrupt status bits are available - * in the IC_RAW_INTR_STAT register. - * - * That is, - * stat = readl(IC_INTR_STAT); - * equals to, - * stat = readl(IC_RAW_INTR_STAT) & readl(IC_INTR_MASK); - * - * The raw version might be useful for debugging purposes. - */ - stat = dw_readl(dev, DW_IC_INTR_STAT); - - /* - * Do not use the IC_CLR_INTR register to clear interrupts, or - * you'll miss some interrupts, triggered during the period from - * readl(IC_INTR_STAT) to readl(IC_CLR_INTR). - * - * Instead, use the separately-prepared IC_CLR_* registers. - */ - if (stat & DW_IC_INTR_RX_UNDER) - dw_readl(dev, DW_IC_CLR_RX_UNDER); - if (stat & DW_IC_INTR_RX_OVER) - dw_readl(dev, DW_IC_CLR_RX_OVER); - if (stat & DW_IC_INTR_TX_OVER) - dw_readl(dev, DW_IC_CLR_TX_OVER); - if (stat & DW_IC_INTR_RD_REQ) - dw_readl(dev, DW_IC_CLR_RD_REQ); - if (stat & DW_IC_INTR_TX_ABRT) { - /* - * The IC_TX_ABRT_SOURCE register is cleared whenever - * the IC_CLR_TX_ABRT is read. Preserve it beforehand. - */ - dev->abort_source = dw_readl(dev, DW_IC_TX_ABRT_SOURCE); - dw_readl(dev, DW_IC_CLR_TX_ABRT); - } - if (stat & DW_IC_INTR_RX_DONE) - dw_readl(dev, DW_IC_CLR_RX_DONE); - if (stat & DW_IC_INTR_ACTIVITY) - dw_readl(dev, DW_IC_CLR_ACTIVITY); - if (stat & DW_IC_INTR_STOP_DET) - dw_readl(dev, DW_IC_CLR_STOP_DET); - if (stat & DW_IC_INTR_START_DET) - dw_readl(dev, DW_IC_CLR_START_DET); - if (stat & DW_IC_INTR_GEN_CALL) - dw_readl(dev, DW_IC_CLR_GEN_CALL); - - return stat; -} - -/* - * Interrupt service routine. This gets called whenever an I2C interrupt - * occurs. - */ -static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id) -{ - struct dw_i2c_dev *dev = dev_id; - u32 stat; - - stat = i2c_dw_read_clear_intrbits(dev); - dev_dbg(dev->dev, "%s: stat=0x%x\n", __func__, stat); - - if (stat & DW_IC_INTR_TX_ABRT) { - dev->cmd_err |= DW_IC_ERR_TX_ABRT; - dev->status = STATUS_IDLE; - - /* - * Anytime TX_ABRT is set, the contents of the tx/rx - * buffers are flushed. Make sure to skip them. - */ - dw_writel(dev, 0, DW_IC_INTR_MASK); - goto tx_aborted; - } - - if (stat & DW_IC_INTR_RX_FULL) - i2c_dw_read(dev); - - if (stat & DW_IC_INTR_TX_EMPTY) - i2c_dw_xfer_msg(dev); - - /* - * No need to modify or disable the interrupt mask here. - * i2c_dw_xfer_msg() will take care of it according to - * the current transmit status. - */ - -tx_aborted: - if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) || dev->msg_err) - complete(&dev->cmd_complete); - - return IRQ_HANDLED; -} - -static struct i2c_algorithm i2c_dw_algo = { - .master_xfer = i2c_dw_xfer, - .functionality = i2c_dw_func, -}; - -static int __devinit dw_i2c_probe(struct platform_device *pdev) -{ - struct dw_i2c_dev *dev; - struct i2c_adapter *adap; - struct resource *mem, *ioarea; - int irq, r; - u32 reg; - - /* NOTE: driver uses the static register mapping */ - mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!mem) { - dev_err(&pdev->dev, "no mem resource?\n"); - return -EINVAL; - } - - irq = platform_get_irq(pdev, 0); - if (irq < 0) { - dev_err(&pdev->dev, "no irq resource?\n"); - return irq; /* -ENXIO */ - } - - ioarea = request_mem_region(mem->start, resource_size(mem), - pdev->name); - if (!ioarea) { - dev_err(&pdev->dev, "I2C region already claimed\n"); - return -EBUSY; - } - - dev = kzalloc(sizeof(struct dw_i2c_dev), GFP_KERNEL); - if (!dev) { - r = -ENOMEM; - goto err_release_region; - } - - init_completion(&dev->cmd_complete); - mutex_init(&dev->lock); - dev->dev = get_device(&pdev->dev); - dev->irq = irq; - platform_set_drvdata(pdev, dev); - - dev->clk = clk_get(&pdev->dev, NULL); - if (IS_ERR(dev->clk)) { - r = -ENODEV; - goto err_free_mem; - } - clk_enable(dev->clk); - - dev->base = ioremap(mem->start, resource_size(mem)); - if (dev->base == NULL) { - dev_err(&pdev->dev, "failure mapping io resources\n"); - r = -EBUSY; - goto err_unuse_clocks; - } - - r = i2c_dw_init(dev); - if (r) - goto err_unuse_clocks; - - reg = dw_readl(dev, DW_IC_COMP_PARAM_1); - dev->tx_fifo_depth = ((reg >> 16) & 0xff) + 1; - dev->rx_fifo_depth = ((reg >> 8) & 0xff) + 1; - - - dw_writel(dev, 0, DW_IC_INTR_MASK); /* disable IRQ */ - r = request_irq(dev->irq, i2c_dw_isr, IRQF_DISABLED, pdev->name, dev); - if (r) { - dev_err(&pdev->dev, "failure requesting irq %i\n", dev->irq); - goto err_iounmap; - } - - adap = &dev->adapter; - i2c_set_adapdata(adap, dev); - adap->owner = THIS_MODULE; - adap->class = I2C_CLASS_HWMON; - strlcpy(adap->name, "Synopsys DesignWare I2C adapter", - sizeof(adap->name)); - adap->algo = &i2c_dw_algo; - adap->dev.parent = &pdev->dev; - - adap->nr = pdev->id; - r = i2c_add_numbered_adapter(adap); - if (r) { - dev_err(&pdev->dev, "failure adding adapter\n"); - goto err_free_irq; - } - - return 0; - -err_free_irq: - free_irq(dev->irq, dev); -err_iounmap: - iounmap(dev->base); -err_unuse_clocks: - clk_disable(dev->clk); - clk_put(dev->clk); - dev->clk = NULL; -err_free_mem: - platform_set_drvdata(pdev, NULL); - put_device(&pdev->dev); - kfree(dev); -err_release_region: - release_mem_region(mem->start, resource_size(mem)); - - return r; -} - -static int __devexit dw_i2c_remove(struct platform_device *pdev) -{ - struct dw_i2c_dev *dev = platform_get_drvdata(pdev); - struct resource *mem; - - platform_set_drvdata(pdev, NULL); - i2c_del_adapter(&dev->adapter); - put_device(&pdev->dev); - - clk_disable(dev->clk); - clk_put(dev->clk); - dev->clk = NULL; - - dw_writel(dev, 0, DW_IC_ENABLE); - free_irq(dev->irq, dev); - kfree(dev); - - mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); - release_mem_region(mem->start, resource_size(mem)); - return 0; -} - -/* work with hotplug and coldplug */ -MODULE_ALIAS("platform:i2c_designware"); - -static struct platform_driver dw_i2c_driver = { - .remove = __devexit_p(dw_i2c_remove), - .driver = { - .name = "i2c_designware", - .owner = THIS_MODULE, - }, -}; - -static int __init dw_i2c_init_driver(void) -{ - return platform_driver_probe(&dw_i2c_driver, dw_i2c_probe); -} -module_init(dw_i2c_init_driver); - -static void __exit dw_i2c_exit_driver(void) -{ - platform_driver_unregister(&dw_i2c_driver); -} -module_exit(dw_i2c_exit_driver); - -MODULE_AUTHOR("Baruch Siach "); -MODULE_DESCRIPTION("Synopsys DesignWare I2C bus adapter"); -MODULE_LICENSE("GPL"); -- cgit v0.10.2 From 1d31b58f648c4f754b23fed4d57acc941080e5ee Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:30 -0700 Subject: i2c-designware: Move retriveving the clock speed out of core code. The clock frequecy supplied to the IP core is specific to a single instance of the driver. This patch makes it possible to have multiple Designware I2C cores in the system possibly running at different core frequencies. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index 38d5a6b..cd52f17 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -142,10 +142,12 @@ static u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset) */ int i2c_dw_init(struct dw_i2c_dev *dev) { - u32 input_clock_khz = clk_get_rate(dev->clk) / 1000; + u32 input_clock_khz; u32 ic_con, hcnt, lcnt; u32 reg; + input_clock_khz = dev->get_clk_rate_khz(dev); + /* Configure register endianess access */ reg = dw_readl(dev, DW_IC_COMP_TYPE); if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) { diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index 4e37031..43de340 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -166,6 +166,7 @@ struct dw_i2c_dev { struct completion cmd_complete; struct mutex lock; struct clk *clk; + u32 (*get_clk_rate_khz) (struct dw_i2c_dev *dev); int cmd_err; struct i2c_msg *msgs; int msgs_num; diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index 9d10ae8..08783a6 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -43,6 +43,10 @@ static struct i2c_algorithm i2c_dw_algo = { .master_xfer = i2c_dw_xfer, .functionality = i2c_dw_func, }; +static u32 i2c_dw_get_clk_rate_khz(struct dw_i2c_dev *dev) +{ + return clk_get_rate(dev->clk)/1000; +} static int __devinit dw_i2c_probe(struct platform_device *pdev) { @@ -84,6 +88,8 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) platform_set_drvdata(pdev, dev); dev->clk = clk_get(&pdev->dev, NULL); + dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz; + if (IS_ERR(dev->clk)) { r = -ENODEV; goto err_free_mem; -- cgit v0.10.2 From 2fa8326b4b1e5fdc889b57b03b1313f3229cb438 Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:31 -0700 Subject: i2c-designware: move i2c functionality bit field to be adapter specific The functionality of the adapter depends on the configuration of the IP block at silicon compile time and is adapter specific. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index cd52f17..7105511 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -457,12 +457,8 @@ done: u32 i2c_dw_func(struct i2c_adapter *adap) { - return I2C_FUNC_I2C | - I2C_FUNC_10BIT_ADDR | - I2C_FUNC_SMBUS_BYTE | - I2C_FUNC_SMBUS_BYTE_DATA | - I2C_FUNC_SMBUS_WORD_DATA | - I2C_FUNC_SMBUS_I2C_BLOCK; + struct dw_i2c_dev *dev = i2c_get_adapdata(adap); + return dev->functionality; } static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev) diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index 43de340..ab4e655 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -182,6 +182,7 @@ struct dw_i2c_dev { int irq; int swab; struct i2c_adapter adapter; + u32 functionality; unsigned int tx_fifo_depth; unsigned int rx_fifo_depth; }; diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index 08783a6..36db7a8 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -96,6 +96,14 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) } clk_enable(dev->clk); + dev->functionality = + I2C_FUNC_I2C | + I2C_FUNC_10BIT_ADDR | + I2C_FUNC_SMBUS_BYTE | + I2C_FUNC_SMBUS_BYTE_DATA | + I2C_FUNC_SMBUS_WORD_DATA | + I2C_FUNC_SMBUS_I2C_BLOCK; + dev->base = ioremap(mem->start, resource_size(mem)); if (dev->base == NULL) { dev_err(&pdev->dev, "failure mapping io resources\n"); -- cgit v0.10.2 From e18563fc560aba0d95a5a73145812a081fb38fac Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:32 -0700 Subject: i2c-designware: move controller config to bus specific portion of driver With multiple I2C adapters possible in the system each running at (possibly) different speeds we need to move the controller configuration bit field to the adapter. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index 7105511..6195df3 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -143,7 +143,7 @@ static u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset) int i2c_dw_init(struct dw_i2c_dev *dev) { u32 input_clock_khz; - u32 ic_con, hcnt, lcnt; + u32 hcnt, lcnt; u32 reg; input_clock_khz = dev->get_clk_rate_khz(dev); @@ -199,9 +199,7 @@ int i2c_dw_init(struct dw_i2c_dev *dev) dw_writel(dev, 0, DW_IC_RX_TL); /* configure the i2c master */ - ic_con = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE | - DW_IC_CON_RESTART_EN | DW_IC_CON_SPEED_FAST; - dw_writel(dev, ic_con, DW_IC_CON); + dw_writel(dev, dev->master_cfg , DW_IC_CON); return 0; } diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index ab4e655..2938621 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -183,6 +183,7 @@ struct dw_i2c_dev { int swab; struct i2c_adapter adapter; u32 functionality; + u32 master_cfg; unsigned int tx_fifo_depth; unsigned int rx_fifo_depth; }; diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index 36db7a8..1258cae 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -103,6 +103,8 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_I2C_BLOCK; + dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE | + DW_IC_CON_RESTART_EN | DW_IC_CON_SPEED_FAST; dev->base = ioremap(mem->start, resource_size(mem)); if (dev->base == NULL) { -- cgit v0.10.2 From af06cf6c8cb600803951ddabe6fb034126752488 Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:33 -0700 Subject: i2c-designware: Support multiple cores using same ISR Add check to make sure that the core is enabled and has outstanding interrupts. The activity bit is masked due to the fact that it will stay active even after the controller has been disabled until the contoller internal state machines have settled. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index 6195df3..e8b83d9 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -521,10 +521,16 @@ static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev) irqreturn_t i2c_dw_isr(int this_irq, void *dev_id) { struct dw_i2c_dev *dev = dev_id; - u32 stat; + u32 stat, enabled; + + enabled = dw_readl(dev, DW_IC_ENABLE); + stat = dw_readl(dev, DW_IC_RAW_INTR_STAT); + dev_dbg(dev->dev, "%s: %s enabled= 0x%x stat=0x%x\n", __func__, + dev->adapter.name, enabled, stat); + if (!enabled || !(stat & ~DW_IC_INTR_ACTIVITY)) + return IRQ_NONE; stat = i2c_dw_read_clear_intrbits(dev); - dev_dbg(dev->dev, "%s: stat=0x%x\n", __func__, stat); if (stat & DW_IC_INTR_TX_ABRT) { dev->cmd_err |= DW_IC_ERR_TX_ABRT; -- cgit v0.10.2 From f3fa9f3da5621154323775ff0efdba99dcebcee4 Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:34 -0700 Subject: i2c-designware: Push all register reads/writes into the core code. Move all register manipulation code into the core, also move register offset definitions to i2c-designware-core.c since the bus specific portions of the driver no longer need/use them. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index e8b83d9..b9f18dd 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -34,6 +34,108 @@ #include #include "i2c-designware-core.h" +/* + * Registers offset + */ +#define DW_IC_CON 0x0 +#define DW_IC_TAR 0x4 +#define DW_IC_DATA_CMD 0x10 +#define DW_IC_SS_SCL_HCNT 0x14 +#define DW_IC_SS_SCL_LCNT 0x18 +#define DW_IC_FS_SCL_HCNT 0x1c +#define DW_IC_FS_SCL_LCNT 0x20 +#define DW_IC_INTR_STAT 0x2c +#define DW_IC_INTR_MASK 0x30 +#define DW_IC_RAW_INTR_STAT 0x34 +#define DW_IC_RX_TL 0x38 +#define DW_IC_TX_TL 0x3c +#define DW_IC_CLR_INTR 0x40 +#define DW_IC_CLR_RX_UNDER 0x44 +#define DW_IC_CLR_RX_OVER 0x48 +#define DW_IC_CLR_TX_OVER 0x4c +#define DW_IC_CLR_RD_REQ 0x50 +#define DW_IC_CLR_TX_ABRT 0x54 +#define DW_IC_CLR_RX_DONE 0x58 +#define DW_IC_CLR_ACTIVITY 0x5c +#define DW_IC_CLR_STOP_DET 0x60 +#define DW_IC_CLR_START_DET 0x64 +#define DW_IC_CLR_GEN_CALL 0x68 +#define DW_IC_ENABLE 0x6c +#define DW_IC_STATUS 0x70 +#define DW_IC_TXFLR 0x74 +#define DW_IC_RXFLR 0x78 +#define DW_IC_TX_ABRT_SOURCE 0x80 +#define DW_IC_COMP_PARAM_1 0xf4 +#define DW_IC_COMP_TYPE 0xfc +#define DW_IC_COMP_TYPE_VALUE 0x44570140 + +#define DW_IC_INTR_RX_UNDER 0x001 +#define DW_IC_INTR_RX_OVER 0x002 +#define DW_IC_INTR_RX_FULL 0x004 +#define DW_IC_INTR_TX_OVER 0x008 +#define DW_IC_INTR_TX_EMPTY 0x010 +#define DW_IC_INTR_RD_REQ 0x020 +#define DW_IC_INTR_TX_ABRT 0x040 +#define DW_IC_INTR_RX_DONE 0x080 +#define DW_IC_INTR_ACTIVITY 0x100 +#define DW_IC_INTR_STOP_DET 0x200 +#define DW_IC_INTR_START_DET 0x400 +#define DW_IC_INTR_GEN_CALL 0x800 + +#define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \ + DW_IC_INTR_TX_EMPTY | \ + DW_IC_INTR_TX_ABRT | \ + DW_IC_INTR_STOP_DET) + +#define DW_IC_STATUS_ACTIVITY 0x1 + +#define DW_IC_ERR_TX_ABRT 0x1 + +/* + * status codes + */ +#define STATUS_IDLE 0x0 +#define STATUS_WRITE_IN_PROGRESS 0x1 +#define STATUS_READ_IN_PROGRESS 0x2 + +#define TIMEOUT 20 /* ms */ + +/* + * hardware abort codes from the DW_IC_TX_ABRT_SOURCE register + * + * only expected abort codes are listed here + * refer to the datasheet for the full list + */ +#define ABRT_7B_ADDR_NOACK 0 +#define ABRT_10ADDR1_NOACK 1 +#define ABRT_10ADDR2_NOACK 2 +#define ABRT_TXDATA_NOACK 3 +#define ABRT_GCALL_NOACK 4 +#define ABRT_GCALL_READ 5 +#define ABRT_SBYTE_ACKDET 7 +#define ABRT_SBYTE_NORSTRT 9 +#define ABRT_10B_RD_NORSTRT 10 +#define ABRT_MASTER_DIS 11 +#define ARB_LOST 12 + +#define DW_IC_TX_ABRT_7B_ADDR_NOACK (1UL << ABRT_7B_ADDR_NOACK) +#define DW_IC_TX_ABRT_10ADDR1_NOACK (1UL << ABRT_10ADDR1_NOACK) +#define DW_IC_TX_ABRT_10ADDR2_NOACK (1UL << ABRT_10ADDR2_NOACK) +#define DW_IC_TX_ABRT_TXDATA_NOACK (1UL << ABRT_TXDATA_NOACK) +#define DW_IC_TX_ABRT_GCALL_NOACK (1UL << ABRT_GCALL_NOACK) +#define DW_IC_TX_ABRT_GCALL_READ (1UL << ABRT_GCALL_READ) +#define DW_IC_TX_ABRT_SBYTE_ACKDET (1UL << ABRT_SBYTE_ACKDET) +#define DW_IC_TX_ABRT_SBYTE_NORSTRT (1UL << ABRT_SBYTE_NORSTRT) +#define DW_IC_TX_ABRT_10B_RD_NORSTRT (1UL << ABRT_10B_RD_NORSTRT) +#define DW_IC_TX_ABRT_MASTER_DIS (1UL << ABRT_MASTER_DIS) +#define DW_IC_TX_ARB_LOST (1UL << ARB_LOST) + +#define DW_IC_TX_ABRT_NOACK (DW_IC_TX_ABRT_7B_ADDR_NOACK | \ + DW_IC_TX_ABRT_10ADDR1_NOACK | \ + DW_IC_TX_ABRT_10ADDR2_NOACK | \ + DW_IC_TX_ABRT_TXDATA_NOACK | \ + DW_IC_TX_ABRT_GCALL_NOACK) + static char *abort_sources[] = { [ABRT_7B_ADDR_NOACK] = "slave address not acknowledged (7bit mode)", @@ -562,3 +664,36 @@ tx_aborted: return IRQ_HANDLED; } + +void i2c_dw_enable(struct dw_i2c_dev *dev) +{ + /* Enable the adapter */ + dw_writel(dev, 1, DW_IC_ENABLE); +} + +void i2c_dw_disable(struct dw_i2c_dev *dev) +{ + int ret; + + /* Disable controller */ + dw_writel(dev, 0, DW_IC_ENABLE); + + /* Disable all interupts */ + dw_writel(dev, 0, DW_IC_INTR_MASK); + dw_readl(dev, DW_IC_CLR_INTR); +} + +void i2c_dw_clear_int(struct dw_i2c_dev *dev) +{ + dw_readl(dev, DW_IC_CLR_INTR); +} + +void i2c_dw_disable_int(struct dw_i2c_dev *dev) +{ + dw_writel(dev, 0, DW_IC_INTR_MASK); +} + +u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev) +{ + return dw_readl(dev, DW_IC_COMP_PARAM_1); +} diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index 2938621..dc016e2 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -26,40 +26,6 @@ * */ -/* - * Registers offset - */ -#define DW_IC_CON 0x0 -#define DW_IC_TAR 0x4 -#define DW_IC_DATA_CMD 0x10 -#define DW_IC_SS_SCL_HCNT 0x14 -#define DW_IC_SS_SCL_LCNT 0x18 -#define DW_IC_FS_SCL_HCNT 0x1c -#define DW_IC_FS_SCL_LCNT 0x20 -#define DW_IC_INTR_STAT 0x2c -#define DW_IC_INTR_MASK 0x30 -#define DW_IC_RAW_INTR_STAT 0x34 -#define DW_IC_RX_TL 0x38 -#define DW_IC_TX_TL 0x3c -#define DW_IC_CLR_INTR 0x40 -#define DW_IC_CLR_RX_UNDER 0x44 -#define DW_IC_CLR_RX_OVER 0x48 -#define DW_IC_CLR_TX_OVER 0x4c -#define DW_IC_CLR_RD_REQ 0x50 -#define DW_IC_CLR_TX_ABRT 0x54 -#define DW_IC_CLR_RX_DONE 0x58 -#define DW_IC_CLR_ACTIVITY 0x5c -#define DW_IC_CLR_STOP_DET 0x60 -#define DW_IC_CLR_START_DET 0x64 -#define DW_IC_CLR_GEN_CALL 0x68 -#define DW_IC_ENABLE 0x6c -#define DW_IC_STATUS 0x70 -#define DW_IC_TXFLR 0x74 -#define DW_IC_RXFLR 0x78 -#define DW_IC_TX_ABRT_SOURCE 0x80 -#define DW_IC_COMP_PARAM_1 0xf4 -#define DW_IC_COMP_TYPE 0xfc -#define DW_IC_COMP_TYPE_VALUE 0x44570140 #define DW_IC_CON_MASTER 0x1 #define DW_IC_CON_SPEED_STD 0x2 @@ -68,72 +34,7 @@ #define DW_IC_CON_RESTART_EN 0x20 #define DW_IC_CON_SLAVE_DISABLE 0x40 -#define DW_IC_INTR_RX_UNDER 0x001 -#define DW_IC_INTR_RX_OVER 0x002 -#define DW_IC_INTR_RX_FULL 0x004 -#define DW_IC_INTR_TX_OVER 0x008 -#define DW_IC_INTR_TX_EMPTY 0x010 -#define DW_IC_INTR_RD_REQ 0x020 -#define DW_IC_INTR_TX_ABRT 0x040 -#define DW_IC_INTR_RX_DONE 0x080 -#define DW_IC_INTR_ACTIVITY 0x100 -#define DW_IC_INTR_STOP_DET 0x200 -#define DW_IC_INTR_START_DET 0x400 -#define DW_IC_INTR_GEN_CALL 0x800 - -#define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \ - DW_IC_INTR_TX_EMPTY | \ - DW_IC_INTR_TX_ABRT | \ - DW_IC_INTR_STOP_DET) - -#define DW_IC_STATUS_ACTIVITY 0x1 - -#define DW_IC_ERR_TX_ABRT 0x1 - -/* - * status codes - */ -#define STATUS_IDLE 0x0 -#define STATUS_WRITE_IN_PROGRESS 0x1 -#define STATUS_READ_IN_PROGRESS 0x2 - -#define TIMEOUT 20 /* ms */ - -/* - * hardware abort codes from the DW_IC_TX_ABRT_SOURCE register - * - * only expected abort codes are listed here - * refer to the datasheet for the full list - */ -#define ABRT_7B_ADDR_NOACK 0 -#define ABRT_10ADDR1_NOACK 1 -#define ABRT_10ADDR2_NOACK 2 -#define ABRT_TXDATA_NOACK 3 -#define ABRT_GCALL_NOACK 4 -#define ABRT_GCALL_READ 5 -#define ABRT_SBYTE_ACKDET 7 -#define ABRT_SBYTE_NORSTRT 9 -#define ABRT_10B_RD_NORSTRT 10 -#define ABRT_MASTER_DIS 11 -#define ARB_LOST 12 - -#define DW_IC_TX_ABRT_7B_ADDR_NOACK (1UL << ABRT_7B_ADDR_NOACK) -#define DW_IC_TX_ABRT_10ADDR1_NOACK (1UL << ABRT_10ADDR1_NOACK) -#define DW_IC_TX_ABRT_10ADDR2_NOACK (1UL << ABRT_10ADDR2_NOACK) -#define DW_IC_TX_ABRT_TXDATA_NOACK (1UL << ABRT_TXDATA_NOACK) -#define DW_IC_TX_ABRT_GCALL_NOACK (1UL << ABRT_GCALL_NOACK) -#define DW_IC_TX_ABRT_GCALL_READ (1UL << ABRT_GCALL_READ) -#define DW_IC_TX_ABRT_SBYTE_ACKDET (1UL << ABRT_SBYTE_ACKDET) -#define DW_IC_TX_ABRT_SBYTE_NORSTRT (1UL << ABRT_SBYTE_NORSTRT) -#define DW_IC_TX_ABRT_10B_RD_NORSTRT (1UL << ABRT_10B_RD_NORSTRT) -#define DW_IC_TX_ABRT_MASTER_DIS (1UL << ABRT_MASTER_DIS) -#define DW_IC_TX_ARB_LOST (1UL << ARB_LOST) -#define DW_IC_TX_ABRT_NOACK (DW_IC_TX_ABRT_7B_ADDR_NOACK | \ - DW_IC_TX_ABRT_10ADDR1_NOACK | \ - DW_IC_TX_ABRT_10ADDR2_NOACK | \ - DW_IC_TX_ABRT_TXDATA_NOACK | \ - DW_IC_TX_ABRT_GCALL_NOACK) /** * struct dw_i2c_dev - private i2c-designware data * @dev: driver model device node @@ -195,3 +96,8 @@ extern int i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num); extern u32 i2c_dw_func(struct i2c_adapter *adap); extern irqreturn_t i2c_dw_isr(int this_irq, void *dev_id); +extern void i2c_dw_enable(struct dw_i2c_dev *dev); +extern void i2c_dw_disable(struct dw_i2c_dev *dev); +extern void i2c_dw_clear_int(struct dw_i2c_dev *dev); +extern void i2c_dw_disable_int(struct dw_i2c_dev *dev); +extern u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev); diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index 1258cae..2d3657a 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -113,7 +113,7 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) goto err_unuse_clocks; } { - u32 param1 = dw_readl(dev, DW_IC_COMP_PARAM_1); + u32 param1 = i2c_dw_read_comp_param(dev); dev->tx_fifo_depth = ((param1 >> 16) & 0xff) + 1; dev->rx_fifo_depth = ((param1 >> 8) & 0xff) + 1; @@ -122,7 +122,7 @@ static int __devinit dw_i2c_probe(struct platform_device *pdev) if (r) goto err_iounmap; - dw_writel(dev, 0, DW_IC_INTR_MASK); /* disable IRQ */ + i2c_dw_disable_int(dev); r = request_irq(dev->irq, i2c_dw_isr, IRQF_DISABLED, pdev->name, dev); if (r) { dev_err(&pdev->dev, "failure requesting irq %i\n", dev->irq); @@ -178,7 +178,7 @@ static int __devexit dw_i2c_remove(struct platform_device *pdev) clk_put(dev->clk); dev->clk = NULL; - dw_writel(dev, 0, DW_IC_ENABLE); + i2c_dw_disable(dev); free_irq(dev->irq, dev); kfree(dev); -- cgit v0.10.2 From fe20ff5c7e9ca7f5369aacc7d7ca3efeda3b90fe Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:35 -0700 Subject: i2c-designware: Add support for Designware core behind PCI devices. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index e6f6e88..1d7ce9c 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -360,6 +360,16 @@ config I2C_DESIGNWARE_PLATFORM This driver can also be built as a module. If so, the module will be called i2c-designware-platform. +config I2C_DESIGNWARE_PCI + tristate "Synopsys DesignWare PCI" + depends on PCI + help + If you say yes to this option, support will be included for the + Synopsys DesignWare I2C adapter. Only master mode is supported. + + This driver can also be built as a module. If so, the module + will be called i2c-designware-pci. + config I2C_GPIO tristate "GPIO-based bitbanging I2C" depends on GENERIC_GPIO diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index d7fe55f..fba6da6 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -35,6 +35,8 @@ obj-$(CONFIG_I2C_CPM) += i2c-cpm.o obj-$(CONFIG_I2C_DAVINCI) += i2c-davinci.o obj-$(CONFIG_I2C_DESIGNWARE_PLATFORM) += i2c-designware-platform.o i2c-designware-platform-objs := i2c-designware-platdrv.o i2c-designware-core.o +obj-$(CONFIG_I2C_DESIGNWARE_PCI) += i2c-designware-pci.o +i2c-designware-pci-objs := i2c-designware-pcidrv.o i2c-designware-core.o obj-$(CONFIG_I2C_GPIO) += i2c-gpio.o obj-$(CONFIG_I2C_HIGHLANDER) += i2c-highlander.o obj-$(CONFIG_I2C_IBM_IIC) += i2c-ibm_iic.o diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index dc016e2..601dd67 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -68,6 +68,7 @@ struct dw_i2c_dev { struct mutex lock; struct clk *clk; u32 (*get_clk_rate_khz) (struct dw_i2c_dev *dev); + struct dw_pci_controller *controller; int cmd_err; struct i2c_msg *msgs; int msgs_num; diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c new file mode 100644 index 0000000..83307ef --- /dev/null +++ b/drivers/i2c/busses/i2c-designware-pcidrv.c @@ -0,0 +1,316 @@ +/* + * Synopsys DesignWare I2C adapter driver (master only). + * + * Based on the TI DAVINCI I2C adapter driver. + * + * Copyright (C) 2006 Texas Instruments. + * Copyright (C) 2007 MontaVista Software Inc. + * Copyright (C) 2009 Provigent Ltd. + * Copyright (C) 2011 Intel corporation. + * + * ---------------------------------------------------------------------------- + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "i2c-designware-core.h" + +#define DRIVER_NAME "i2c-designware-pci" + +enum dw_pci_ctl_id_t { + moorestown_0, + moorestown_1, + moorestown_2, + + medfield_0, + medfield_1, + medfield_2, + medfield_3, + medfield_4, + medfield_5, +}; + +struct dw_pci_controller { + u32 bus_num; + u32 bus_cfg; + u32 tx_fifo_depth; + u32 rx_fifo_depth; + u32 clk_khz; +}; + +#define INTEL_MID_STD_CFG (DW_IC_CON_MASTER | \ + DW_IC_CON_SLAVE_DISABLE | \ + DW_IC_CON_RESTART_EN) + +static struct dw_pci_controller dw_pci_controllers[] = { + [moorestown_0] = { + .bus_num = 0, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [moorestown_1] = { + .bus_num = 1, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [moorestown_2] = { + .bus_num = 2, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [medfield_0] = { + .bus_num = 0, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [medfield_1] = { + .bus_num = 1, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [medfield_2] = { + .bus_num = 2, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [medfield_3] = { + .bus_num = 3, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_STD, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [medfield_4] = { + .bus_num = 4, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, + [medfield_5] = { + .bus_num = 5, + .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, + .tx_fifo_depth = 32, + .rx_fifo_depth = 32, + .clk_khz = 25000, + }, +}; +static struct i2c_algorithm i2c_dw_algo = { + .master_xfer = i2c_dw_xfer, + .functionality = i2c_dw_func, +}; + +static u32 i2c_dw_get_clk_rate_khz(struct dw_i2c_dev *dev) +{ + return dev->controller->clk_khz; +} + +static int __devinit i2c_dw_pci_probe(struct pci_dev *pdev, +const struct pci_device_id *id) +{ + struct dw_i2c_dev *dev; + struct i2c_adapter *adap; + unsigned long start, len; + void __iomem *base; + int r; + struct dw_pci_controller *controller; + + if (id->driver_data >= ARRAY_SIZE(dw_pci_controllers)) { + printk(KERN_ERR "dw_i2c_pci_probe: invalid driver data %ld\n", + id->driver_data); + return -EINVAL; + } + + controller = &dw_pci_controllers[id->driver_data]; + + r = pci_enable_device(pdev); + if (r) { + dev_err(&pdev->dev, "Failed to enable I2C PCI device (%d)\n", + r); + goto exit; + } + + /* Determine the address of the I2C area */ + start = pci_resource_start(pdev, 0); + len = pci_resource_len(pdev, 0); + if (!start || len == 0) { + dev_err(&pdev->dev, "base address not set\n"); + r = -ENODEV; + goto exit; + } + + r = pci_request_region(pdev, 0, DRIVER_NAME); + if (r) { + dev_err(&pdev->dev, "failed to request I2C region " + "0x%lx-0x%lx\n", start, + (unsigned long)pci_resource_end(pdev, 0)); + goto exit; + } + + base = ioremap_nocache(start, len); + if (!base) { + dev_err(&pdev->dev, "I/O memory remapping failed\n"); + r = -ENOMEM; + goto err_release_region; + } + + + dev = kzalloc(sizeof(struct dw_i2c_dev), GFP_KERNEL); + if (!dev) { + r = -ENOMEM; + goto err_release_region; + } + + init_completion(&dev->cmd_complete); + mutex_init(&dev->lock); + dev->clk = NULL; + dev->controller = controller; + dev->get_clk_rate_khz = i2c_dw_get_clk_rate_khz; + dev->base = base; + dev->dev = get_device(&pdev->dev); + dev->functionality = + I2C_FUNC_I2C | + I2C_FUNC_SMBUS_BYTE | + I2C_FUNC_SMBUS_BYTE_DATA | + I2C_FUNC_SMBUS_WORD_DATA | + I2C_FUNC_SMBUS_I2C_BLOCK; + dev->master_cfg = controller->bus_cfg; + + pci_set_drvdata(pdev, dev); + + dev->tx_fifo_depth = controller->tx_fifo_depth; + dev->rx_fifo_depth = controller->rx_fifo_depth; + r = i2c_dw_init(dev); + if (r) + goto err_iounmap; + + adap = &dev->adapter; + i2c_set_adapdata(adap, dev); + adap->owner = THIS_MODULE; + adap->class = 0; + adap->algo = &i2c_dw_algo; + adap->dev.parent = &pdev->dev; + adap->nr = controller->bus_num; + snprintf(adap->name, sizeof(adap->name), "i2c-designware-pci-%d", + adap->nr); + + r = request_irq(pdev->irq, i2c_dw_isr, IRQF_SHARED, adap->name, dev); + if (r) { + dev_err(&pdev->dev, "failure requesting irq %i\n", dev->irq); + goto err_iounmap; + } + + i2c_dw_disable_int(dev); + i2c_dw_clear_int(dev); + r = i2c_add_numbered_adapter(adap); + if (r) { + dev_err(&pdev->dev, "failure adding adapter\n"); + goto err_free_irq; + } + + return 0; + +err_free_irq: + free_irq(pdev->irq, dev); +err_iounmap: + iounmap(dev->base); + pci_set_drvdata(pdev, NULL); + put_device(&pdev->dev); + kfree(dev); +err_release_region: + pci_release_region(pdev, 0); +exit: + return r; +} + +static void __devexit i2c_dw_pci_remove(struct pci_dev *pdev) +{ + struct dw_i2c_dev *dev = pci_get_drvdata(pdev); + + pci_set_drvdata(pdev, NULL); + i2c_del_adapter(&dev->adapter); + put_device(&pdev->dev); + + free_irq(dev->irq, dev); + kfree(dev); + pci_release_region(pdev, 0); +} + +/* work with hotplug and coldplug */ +MODULE_ALIAS("i2c_designware-pci"); + +DEFINE_PCI_DEVICE_TABLE(i2_designware_pci_ids) = { + /* Moorestown */ + { PCI_VDEVICE(INTEL, 0x0802), moorestown_0 }, + { PCI_VDEVICE(INTEL, 0x0803), moorestown_1 }, + { PCI_VDEVICE(INTEL, 0x0804), moorestown_2 }, + /* Medfield */ + { PCI_VDEVICE(INTEL, 0x0817), medfield_3,}, + { PCI_VDEVICE(INTEL, 0x0818), medfield_4 }, + { PCI_VDEVICE(INTEL, 0x0819), medfield_5 }, + { PCI_VDEVICE(INTEL, 0x082C), medfield_0 }, + { PCI_VDEVICE(INTEL, 0x082D), medfield_1 }, + { PCI_VDEVICE(INTEL, 0x082E), medfield_2 }, + { 0,} +}; +MODULE_DEVICE_TABLE(pci, i2_designware_pci_ids); + +static struct pci_driver dw_i2c_driver = { + .name = DRIVER_NAME, + .id_table = i2_designware_pci_ids, + .probe = i2c_dw_pci_probe, + .remove = __devexit_p(i2c_dw_pci_remove), +}; + +static int __init dw_i2c_init_driver(void) +{ + return pci_register_driver(&dw_i2c_driver); +} +module_init(dw_i2c_init_driver); + +static void __exit dw_i2c_exit_driver(void) +{ + pci_unregister_driver(&dw_i2c_driver); +} +module_exit(dw_i2c_exit_driver); + +MODULE_AUTHOR("Baruch Siach "); +MODULE_DESCRIPTION("Synopsys DesignWare PCI I2C bus adapter"); +MODULE_LICENSE("GPL"); -- cgit v0.10.2 From 18dbdda89f5cf0540e577280395f16079308e87d Mon Sep 17 00:00:00 2001 From: Dirk Brandewie Date: Thu, 6 Oct 2011 11:26:36 -0700 Subject: i2c-designware: Add runtime power management support Add runtime power management to the PCI driver. Signed-off-by: Dirk Brandewie Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index b9f18dd..df87992 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -31,6 +31,7 @@ #include #include #include +#include #include #include "i2c-designware-core.h" @@ -501,6 +502,7 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) dev_dbg(dev->dev, "%s: msgs: %d\n", __func__, num); mutex_lock(&dev->lock); + pm_runtime_get_sync(dev->dev); INIT_COMPLETION(dev->cmd_complete); dev->msgs = msgs; @@ -550,6 +552,7 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) ret = -EIO; done: + pm_runtime_put(dev->dev); mutex_unlock(&dev->lock); return ret; @@ -671,10 +674,13 @@ void i2c_dw_enable(struct dw_i2c_dev *dev) dw_writel(dev, 1, DW_IC_ENABLE); } -void i2c_dw_disable(struct dw_i2c_dev *dev) +u32 i2c_dw_is_enabled(struct dw_i2c_dev *dev) { - int ret; + return dw_readl(dev, DW_IC_ENABLE); +} +void i2c_dw_disable(struct dw_i2c_dev *dev) +{ /* Disable controller */ dw_writel(dev, 0, DW_IC_ENABLE); diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index 601dd67..02d1a2d 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -98,6 +98,7 @@ extern int i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], extern u32 i2c_dw_func(struct i2c_adapter *adap); extern irqreturn_t i2c_dw_isr(int this_irq, void *dev_id); extern void i2c_dw_enable(struct dw_i2c_dev *dev); +extern u32 i2c_dw_is_enabled(struct dw_i2c_dev *dev); extern void i2c_dw_disable(struct dw_i2c_dev *dev); extern void i2c_dw_clear_int(struct dw_i2c_dev *dev); extern void i2c_dw_disable_int(struct dw_i2c_dev *dev); diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c index 83307ef..d2223b5 100644 --- a/drivers/i2c/busses/i2c-designware-pcidrv.c +++ b/drivers/i2c/busses/i2c-designware-pcidrv.c @@ -38,6 +38,7 @@ #include #include #include +#include #include "i2c-designware-core.h" #define DRIVER_NAME "i2c-designware-pci" @@ -137,6 +138,82 @@ static struct i2c_algorithm i2c_dw_algo = { .functionality = i2c_dw_func, }; +static int i2c_dw_pci_suspend(struct pci_dev *pdev, pm_message_t mesg) +{ + struct dw_i2c_dev *i2c = pci_get_drvdata(pdev); + int err; + + + i2c_dw_disable(i2c); + + err = pci_save_state(pdev); + if (err) { + dev_err(&pdev->dev, "pci_save_state failed\n"); + return err; + } + + err = pci_set_power_state(pdev, PCI_D3hot); + if (err) { + dev_err(&pdev->dev, "pci_set_power_state failed\n"); + return err; + } + + return 0; +} + +static int i2c_dw_pci_runtime_suspend(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + dev_dbg(dev, "PCI suspend called\n"); + return i2c_dw_pci_suspend(pdev, PMSG_SUSPEND); +} + +static int i2c_dw_pci_resume(struct pci_dev *pdev) +{ + struct dw_i2c_dev *i2c = pci_get_drvdata(pdev); + int err; + u32 enabled; + + enabled = i2c_dw_is_enabled(i2c); + if (enabled) + return 0; + + err = pci_set_power_state(pdev, PCI_D0); + if (err) { + dev_err(&pdev->dev, "pci_set_power_state() failed\n"); + return err; + } + + pci_restore_state(pdev); + + i2c_dw_init(i2c); + i2c_dw_enable(i2c); + return 0; +} + +static int i2c_dw_pci_runtime_resume(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + dev_dbg(dev, "runtime_resume called\n"); + return i2c_dw_pci_resume(pdev); +} + +static int i2c_dw_pci_runtime_idle(struct device *dev) +{ + int err = pm_schedule_suspend(dev, 500); + dev_dbg(dev, "runtime_idle called\n"); + + if (err != 0) + return 0; + return -EBUSY; +} + +static const struct dev_pm_ops i2c_dw_pm_ops = { + .runtime_suspend = i2c_dw_pci_runtime_suspend, + .runtime_resume = i2c_dw_pci_runtime_resume, + .runtime_idle = i2c_dw_pci_runtime_idle, +}; + static u32 i2c_dw_get_clk_rate_khz(struct dw_i2c_dev *dev) { return dev->controller->clk_khz; @@ -245,6 +322,9 @@ const struct pci_device_id *id) goto err_free_irq; } + pm_runtime_put_noidle(&pdev->dev); + pm_runtime_allow(&pdev->dev); + return 0; err_free_irq: @@ -264,6 +344,10 @@ static void __devexit i2c_dw_pci_remove(struct pci_dev *pdev) { struct dw_i2c_dev *dev = pci_get_drvdata(pdev); + i2c_dw_disable(dev); + pm_runtime_forbid(&pdev->dev); + pm_runtime_get_noresume(&pdev->dev); + pci_set_drvdata(pdev, NULL); i2c_del_adapter(&dev->adapter); put_device(&pdev->dev); @@ -297,6 +381,11 @@ static struct pci_driver dw_i2c_driver = { .id_table = i2_designware_pci_ids, .probe = i2c_dw_pci_probe, .remove = __devexit_p(i2c_dw_pci_remove), + .resume = i2c_dw_pci_resume, + .suspend = i2c_dw_pci_suspend, + .driver = { + .pm = &i2c_dw_pm_ops, + }, }; static int __init dw_i2c_init_driver(void) -- cgit v0.10.2 From 52c2843322362bfd847bdda1d3cebc751de68e5b Mon Sep 17 00:00:00 2001 From: Octavian Purdila Date: Thu, 6 Oct 2011 11:26:37 -0700 Subject: i2c-designware: Fix PCI core warning on suspend/resume PCI core warns if the legacy PM and new PM functions are present. Update the driver to only use the new power management framework. This patch fixes the following warning seen during suspend/resume: <7>[ 24.193850] i2c-designware-pci 0000:08:13.0: suspend <4>[ 24.193866] ------------[ cut here ]------------ <4>[ 24.193892] WARNING: at drivers/pci/pci-driver.c:605 pci_has_legacy_pm_support+0x48/0x4d() <4>[ 24.193925] Hardware name: OakTrail <4>[ 24.193936] Modules linked in: <4>[ 24.193958] Pid: 2834, comm: kworker/u:22 Tainted: G W 2.6.36greenridge-01402-gc8047e6 #171 <4>[ 24.193974] Call Trace: <4>[ 24.193999] [] warn_slowpath_common+0x66/0xc2 <4>[ 24.194025] [] ? pci_has_legacy_pm_support+0x48/0x4d <4>[ 24.194052] [] warn_slowpath_null+0xf/0x13 <4>[ 24.194079] [] pci_has_legacy_pm_support+0x48/0x4d <4>[ 24.194106] [] pci_pm_suspend+0x22/0x154 <4>[ 24.194131] [] ? pci_pm_suspend+0x0/0x154 <4>[ 24.194156] [] pm_op+0x3e/0x95 <4>[ 24.194182] [] __device_suspend+0x12e/0x194 <4>[ 24.194208] [] ? dpm_drv_timeout+0x0/0x47 <4>[ 24.194237] [] async_suspend+0x16/0x3a <4>[ 24.194265] [] async_run_entry_fn+0x97/0x135 <4>[ 24.194291] [] process_one_work+0x1c9/0x2db Signed-off-by: Octavian Purdila Signed-off-by: Dirk Brandewie Signed-off-by: Alan Cox Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c index d2223b5..9e89e73 100644 --- a/drivers/i2c/busses/i2c-designware-pcidrv.c +++ b/drivers/i2c/busses/i2c-designware-pcidrv.c @@ -138,8 +138,9 @@ static struct i2c_algorithm i2c_dw_algo = { .functionality = i2c_dw_func, }; -static int i2c_dw_pci_suspend(struct pci_dev *pdev, pm_message_t mesg) +static int i2c_dw_pci_suspend(struct device *dev) { + struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); struct dw_i2c_dev *i2c = pci_get_drvdata(pdev); int err; @@ -161,15 +162,9 @@ static int i2c_dw_pci_suspend(struct pci_dev *pdev, pm_message_t mesg) return 0; } -static int i2c_dw_pci_runtime_suspend(struct device *dev) -{ - struct pci_dev *pdev = to_pci_dev(dev); - dev_dbg(dev, "PCI suspend called\n"); - return i2c_dw_pci_suspend(pdev, PMSG_SUSPEND); -} - -static int i2c_dw_pci_resume(struct pci_dev *pdev) +static int i2c_dw_pci_resume(struct device *dev) { + struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); struct dw_i2c_dev *i2c = pci_get_drvdata(pdev); int err; u32 enabled; @@ -191,13 +186,6 @@ static int i2c_dw_pci_resume(struct pci_dev *pdev) return 0; } -static int i2c_dw_pci_runtime_resume(struct device *dev) -{ - struct pci_dev *pdev = to_pci_dev(dev); - dev_dbg(dev, "runtime_resume called\n"); - return i2c_dw_pci_resume(pdev); -} - static int i2c_dw_pci_runtime_idle(struct device *dev) { int err = pm_schedule_suspend(dev, 500); @@ -209,9 +197,10 @@ static int i2c_dw_pci_runtime_idle(struct device *dev) } static const struct dev_pm_ops i2c_dw_pm_ops = { - .runtime_suspend = i2c_dw_pci_runtime_suspend, - .runtime_resume = i2c_dw_pci_runtime_resume, - .runtime_idle = i2c_dw_pci_runtime_idle, + .resume = i2c_dw_pci_resume, + .suspend = i2c_dw_pci_suspend, + SET_RUNTIME_PM_OPS(i2c_dw_pci_suspend, i2c_dw_pci_resume, + i2c_dw_pci_runtime_idle) }; static u32 i2c_dw_get_clk_rate_khz(struct dw_i2c_dev *dev) @@ -381,8 +370,6 @@ static struct pci_driver dw_i2c_driver = { .id_table = i2_designware_pci_ids, .probe = i2c_dw_pci_probe, .remove = __devexit_p(i2c_dw_pci_remove), - .resume = i2c_dw_pci_resume, - .suspend = i2c_dw_pci_suspend, .driver = { .pm = &i2c_dw_pm_ops, }, -- cgit v0.10.2 From 93e4ad74da14c8d5564cfc0b57c40ca311e53d47 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Wed, 12 Oct 2011 13:13:00 +0900 Subject: i2c-eg20t: Fix bus-idle waiting issue Currently, when checking whether bus is idle or not, if timeout occurs, this function always returns success(zero). This patch fixes the issue. Signed-off-by: Tomoya MORINAGA Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index ce1a32b..a4f76cb 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -273,23 +273,23 @@ static s32 pch_i2c_wait_for_bus_idle(struct i2c_algo_pch_data *adap, s32 timeout) { void __iomem *p = adap->pch_base_address; + ktime_t ns_val; + + if ((ioread32(p + PCH_I2CSR) & I2CMBB_BIT) == 0) + return 0; /* MAX timeout value is timeout*1000*1000nsec */ - ktime_t ns_val = ktime_add_ns(ktime_get(), timeout*1000*1000); + ns_val = ktime_add_ns(ktime_get(), timeout*1000*1000); do { - if ((ioread32(p + PCH_I2CSR) & I2CMBB_BIT) == 0) - break; msleep(20); + if ((ioread32(p + PCH_I2CSR) & I2CMBB_BIT) == 0) + return 0; } while (ktime_lt(ktime_get(), ns_val)); pch_dbg(adap, "I2CSR = %x\n", ioread32(p + PCH_I2CSR)); + pch_err(adap, "%s: Timeout Error.return%d\n", __func__, -ETIME); - if (timeout == 0) { - pch_err(adap, "%s: Timeout Error.return%d\n", __func__, -ETIME); - return -ETIME; - } - - return 0; + return -ETIME; } /** -- cgit v0.10.2 From c7b41f3affc63644f398b5faa170b1f531b406a8 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Wed, 12 Oct 2011 13:13:01 +0900 Subject: i2c-eg20t: Modify returned value s32 to long Type of wait_event_timeout is long not s32. This patch replaces s32 with long. Additionally, delete negative processing(ret < 0). Signed-off-by: Tomoya MORINAGA Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index a4f76cb..543d39c 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -311,13 +311,9 @@ static void pch_i2c_start(struct i2c_algo_pch_data *adap) */ static s32 pch_i2c_wait_for_xfer_complete(struct i2c_algo_pch_data *adap) { - s32 ret; + long ret; ret = wait_event_timeout(pch_event, (adap->pch_event_flag != 0), msecs_to_jiffies(50)); - if (ret < 0) { - pch_err(adap, "timeout: %x\n", adap->pch_event_flag); - return ret; - } if (ret == 0) { pch_err(adap, "timeout: %x\n", adap->pch_event_flag); -- cgit v0.10.2 From c249ac207f2cedb49f2c9442afbaac35bfcfcd25 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Wed, 12 Oct 2011 13:13:02 +0900 Subject: i2c-eg20t: Fix 10bit access issue Reported-by: Jeffrey (Sheng-Hui) Chu Signed-off-by: Tomoya MORINAGA Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index 543d39c..38e44d9 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -64,6 +64,7 @@ #define TEN_BIT_ADDR_DEFAULT 0xF000 #define TEN_BIT_ADDR_MASK 0xF0 #define PCH_START 0x0020 +#define PCH_RESTART 0x0004 #define PCH_ESR_START 0x0001 #define PCH_BUFF_START 0x1 #define PCH_REPSTART 0x0004 @@ -408,7 +409,7 @@ static s32 pch_i2c_writebytes(struct i2c_adapter *i2c_adap, } if (msgs->flags & I2C_M_TEN) { - addr_2_msb = ((addr & I2C_MSB_2B_MSK) >> 7); + addr_2_msb = ((addr & I2C_MSB_2B_MSK) >> 7) & 0x06; iowrite32(addr_2_msb | TEN_BIT_ADDR_MASK, p + PCH_I2CDR); if (first) pch_i2c_start(adap); @@ -480,6 +481,19 @@ static void pch_i2c_sendnack(struct i2c_algo_pch_data *adap) } /** + * pch_i2c_restart() - Generate I2C restart condition in normal mode. + * @adap: Pointer to struct i2c_algo_pch_data. + * + * Generate I2C restart condition in normal mode by setting I2CCTL.I2CRSTA. + */ +static void pch_i2c_restart(struct i2c_algo_pch_data *adap) +{ + void __iomem *p = adap->pch_base_address; + pch_dbg(adap, "I2CCTL = %x\n", ioread32(p + PCH_I2CCTL)); + pch_setbit(adap->pch_base_address, PCH_I2CCTL, PCH_RESTART); +} + +/** * pch_i2c_readbytes() - read data from I2C bus in normal mode. * @i2c_adap: Pointer to the struct i2c_adapter. * @msgs: Pointer to i2c_msg structure. @@ -496,6 +510,7 @@ static s32 pch_i2c_readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, u32 length; u32 addr; u32 addr_2_msb; + u32 addr_8_lsb; void __iomem *p = adap->pch_base_address; length = msgs->len; @@ -511,9 +526,55 @@ static s32 pch_i2c_readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, } if (msgs->flags & I2C_M_TEN) { - addr_2_msb = (((addr & I2C_MSB_2B_MSK) >> 7) | (I2C_RD)); + addr_2_msb = ((addr & I2C_MSB_2B_MSK) >> 7); iowrite32(addr_2_msb | TEN_BIT_ADDR_MASK, p + PCH_I2CDR); + if (first) + pch_i2c_start(adap); + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave address" + "setting\n"); + return -EIO; + } + addr_8_lsb = (addr & I2C_ADDR_MSK); + iowrite32(addr_8_lsb, p + PCH_I2CDR); + } else if (rtn == -EIO) { /* Arbitration Lost */ + pch_err(adap, "Lost Arbitration\n"); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMAL_BIT); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMIF_BIT); + pch_i2c_init(adap); + return -EAGAIN; + } else { /* wait-event timeout */ + pch_i2c_stop(adap); + return -ETIME; + } + pch_i2c_restart(adap); + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave address" + "setting\n"); + return -EIO; + } + addr_2_msb |= I2C_RD; + iowrite32(addr_2_msb | TEN_BIT_ADDR_MASK, + p + PCH_I2CDR); + } else if (rtn == -EIO) { /* Arbitration Lost */ + pch_err(adap, "Lost Arbitration\n"); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMAL_BIT); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMIF_BIT); + pch_i2c_init(adap); + return -EAGAIN; + } else { /* wait-event timeout */ + pch_i2c_stop(adap); + return -ETIME; + } } else { /* 7 address bits + R/W bit */ addr = (((addr) << 1) | (I2C_RD)); -- cgit v0.10.2 From 12bd3146518ab984c1eb234a0f81756ddc5e3683 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Wed, 12 Oct 2011 13:13:03 +0900 Subject: i2c-eg20t: Separate error processing Error processing for NACK or wait-event must be precessed separately. So divide wait-event error processing into NACK-receiving and timeout. Add arbitration lost processing. Signed-off-by: Tomoya MORINAGA Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index 38e44d9..cb29686 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -391,6 +391,7 @@ static s32 pch_i2c_writebytes(struct i2c_adapter *i2c_adap, u32 addr_2_msb; u32 addr_8_lsb; s32 wrcount; + s32 rtn; void __iomem *p = adap->pch_base_address; length = msgs->len; @@ -413,11 +414,25 @@ static s32 pch_i2c_writebytes(struct i2c_adapter *i2c_adap, iowrite32(addr_2_msb | TEN_BIT_ADDR_MASK, p + PCH_I2CDR); if (first) pch_i2c_start(adap); - if (pch_i2c_wait_for_xfer_complete(adap) == 0 && - pch_i2c_getack(adap) == 0) { + + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave address" + "setting\n"); + return -EIO; + } addr_8_lsb = (addr & I2C_ADDR_MSK); iowrite32(addr_8_lsb, p + PCH_I2CDR); - } else { + } else if (rtn == -EIO) { /* Arbitration Lost */ + pch_err(adap, "Lost Arbitration\n"); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMAL_BIT); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMIF_BIT); + pch_i2c_init(adap); + return -EAGAIN; + } else { /* wait-event timeout */ pch_i2c_stop(adap); return -ETIME; } @@ -428,30 +443,48 @@ static s32 pch_i2c_writebytes(struct i2c_adapter *i2c_adap, pch_i2c_start(adap); } - if ((pch_i2c_wait_for_xfer_complete(adap) == 0) && - (pch_i2c_getack(adap) == 0)) { - for (wrcount = 0; wrcount < length; ++wrcount) { - /* write buffer value to I2C data register */ - iowrite32(buf[wrcount], p + PCH_I2CDR); - pch_dbg(adap, "writing %x to Data register\n", - buf[wrcount]); + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave address" + "setting\n"); + return -EIO; + } + } else if (rtn == -EIO) { /* Arbitration Lost */ + pch_err(adap, "Lost Arbitration\n"); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMAL_BIT); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMIF_BIT); + return -EAGAIN; + } else { /* wait-event timeout */ + return -ETIME; + } - if (pch_i2c_wait_for_xfer_complete(adap) != 0) - return -ETIME; + for (wrcount = 0; wrcount < length; ++wrcount) { + /* write buffer value to I2C data register */ + iowrite32(buf[wrcount], p + PCH_I2CDR); + pch_dbg(adap, "writing %x to Data register\n", buf[wrcount]); - if (pch_i2c_getack(adap)) + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave address" + "setting\n"); return -EIO; + } + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMCF_BIT); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, + I2CMIF_BIT); + } else { /* wait-event timeout */ + return -ETIME; } + } - /* check if this is the last message */ - if (last) - pch_i2c_stop(adap); - else - pch_i2c_repstart(adap); - } else { + /* check if this is the last message */ + if (last) pch_i2c_stop(adap); - return -EIO; - } + else + pch_i2c_repstart(adap); pch_dbg(adap, "return=%d\n", wrcount); @@ -512,6 +545,7 @@ static s32 pch_i2c_readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, u32 addr_2_msb; u32 addr_8_lsb; void __iomem *p = adap->pch_base_address; + s32 rtn; length = msgs->len; buf = msgs->buf; @@ -585,56 +619,79 @@ static s32 pch_i2c_readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, if (first) pch_i2c_start(adap); - if ((pch_i2c_wait_for_xfer_complete(adap) == 0) && - (pch_i2c_getack(adap) == 0)) { - pch_dbg(adap, "return %d\n", 0); + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave address" + "setting\n"); + return -EIO; + } + } else if (rtn == -EIO) { /* Arbitration Lost */ + pch_err(adap, "Lost Arbitration\n"); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMAL_BIT); + pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMIF_BIT); + return -EAGAIN; + } else { /* wait-event timeout */ + return -ETIME; + } - if (length == 0) { - pch_i2c_stop(adap); - ioread32(p + PCH_I2CDR); /* Dummy read needs */ + if (length == 0) { + pch_i2c_stop(adap); + ioread32(p + PCH_I2CDR); /* Dummy read needs */ - count = length; - } else { - int read_index; - int loop; - pch_i2c_sendack(adap); + count = length; + } else { + int read_index; + int loop; + pch_i2c_sendack(adap); - /* Dummy read */ - for (loop = 1, read_index = 0; loop < length; loop++) { - buf[read_index] = ioread32(p + PCH_I2CDR); + /* Dummy read */ + for (loop = 1, read_index = 0; loop < length; loop++) { + buf[read_index] = ioread32(p + PCH_I2CDR); - if (loop != 1) - read_index++; + if (loop != 1) + read_index++; - if (pch_i2c_wait_for_xfer_complete(adap) != 0) { - pch_i2c_stop(adap); - return -ETIME; + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave" + "address setting\n"); + return -EIO; } - } /* end for */ + } else { /* wait-event timeout */ + pch_i2c_stop(adap); + return -ETIME; + } - pch_i2c_sendnack(adap); + } /* end for */ - buf[read_index] = ioread32(p + PCH_I2CDR); + pch_i2c_sendnack(adap); - if (length != 1) - read_index++; + buf[read_index] = ioread32(p + PCH_I2CDR); /* Read final - 1 */ - if (pch_i2c_wait_for_xfer_complete(adap) == 0) { - if (last) - pch_i2c_stop(adap); - else - pch_i2c_repstart(adap); + if (length != 1) + read_index++; - buf[read_index++] = ioread32(p + PCH_I2CDR); - count = read_index; - } else { - count = -ETIME; + rtn = pch_i2c_wait_for_xfer_complete(adap); + if (rtn == 0) { + if (pch_i2c_getack(adap)) { + pch_dbg(adap, "Receive NACK for slave" + "address setting\n"); + return -EIO; } - + } else { /* wait-event timeout */ + pch_i2c_stop(adap); + return -ETIME; } - } else { - count = -ETIME; - pch_i2c_stop(adap); + + if (last) + pch_i2c_stop(adap); + else + pch_i2c_repstart(adap); + + buf[read_index++] = ioread32(p + PCH_I2CDR); /* Read Final */ + count = read_index; } return count; -- cgit v0.10.2 From 3cf21a7c48389c167065bffd61db39a9bd201f07 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Wed, 12 Oct 2011 13:13:04 +0900 Subject: i2c-eg20t: add stop sequence in case wait-event timeout occurs add stop sequence in case wait-event timeout in write processing. (read processing already had it) Signed-off-by: Tomoya MORINAGA Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index cb29686..318e6a5 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -456,6 +456,7 @@ static s32 pch_i2c_writebytes(struct i2c_adapter *i2c_adap, pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMIF_BIT); return -EAGAIN; } else { /* wait-event timeout */ + pch_i2c_stop(adap); return -ETIME; } @@ -476,6 +477,7 @@ static s32 pch_i2c_writebytes(struct i2c_adapter *i2c_adap, pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMIF_BIT); } else { /* wait-event timeout */ + pch_i2c_stop(adap); return -ETIME; } } @@ -632,6 +634,7 @@ static s32 pch_i2c_readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMIF_BIT); return -EAGAIN; } else { /* wait-event timeout */ + pch_i2c_stop(adap); return -ETIME; } -- cgit v0.10.2 From cb59f5253a5313d62e8e345fcd5dd5a44a73e0d6 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Wed, 12 Oct 2011 13:13:05 +0900 Subject: i2c-eg20t: Fix flag setting issue Currently, in case occurring abnormal event, internal flag variable(=pch_event_flag) is not reset. This patch fixes the issue. Signed-off-by: Tomoya MORINAGA Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index 318e6a5..a1bf62d 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -318,11 +318,13 @@ static s32 pch_i2c_wait_for_xfer_complete(struct i2c_algo_pch_data *adap) if (ret == 0) { pch_err(adap, "timeout: %x\n", adap->pch_event_flag); + adap->pch_event_flag = 0; return -ETIMEDOUT; } if (adap->pch_event_flag & I2C_ERROR_MASK) { pch_err(adap, "error bits set: %x\n", adap->pch_event_flag); + adap->pch_event_flag = 0; return -EIO; } -- cgit v0.10.2 From 24597bf8012cf3fa5703c38e1bb13df3118d7588 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Wed, 12 Oct 2011 13:13:06 +0900 Subject: i2c-eg20t: Add initialize processing in case i2c-error occurs In case disconnecting physical connection, need to initialize i2c device for retry access. This patch adds initialize process in case bus-idle fails and Lost arbitration. Signed-off-by: Tomoya MORINAGA Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index a1bf62d..8cebef4 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -289,6 +289,7 @@ static s32 pch_i2c_wait_for_bus_idle(struct i2c_algo_pch_data *adap, pch_dbg(adap, "I2CSR = %x\n", ioread32(p + PCH_I2CSR)); pch_err(adap, "%s: Timeout Error.return%d\n", __func__, -ETIME); + pch_i2c_init(adap); return -ETIME; } @@ -456,6 +457,7 @@ static s32 pch_i2c_writebytes(struct i2c_adapter *i2c_adap, pch_err(adap, "Lost Arbitration\n"); pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMAL_BIT); pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMIF_BIT); + pch_i2c_init(adap); return -EAGAIN; } else { /* wait-event timeout */ pch_i2c_stop(adap); @@ -634,6 +636,7 @@ static s32 pch_i2c_readbytes(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, pch_err(adap, "Lost Arbitration\n"); pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMAL_BIT); pch_clrbit(adap->pch_base_address, PCH_I2CSR, I2CMIF_BIT); + pch_i2c_init(adap); return -EAGAIN; } else { /* wait-event timeout */ pch_i2c_stop(adap); -- cgit v0.10.2 From f533c61e1921b93aa247d72d39c3fbe045340a9a Mon Sep 17 00:00:00 2001 From: Olof Johansson Date: Wed, 12 Oct 2011 17:33:00 -0700 Subject: i2c-tegra: __iomem annotation fix drivers/i2c/busses/i2c-tegra.c:585:7: warning: incorrect type in assignment (different address spaces) drivers/i2c/busses/i2c-tegra.c:585:7: expected void *base drivers/i2c/busses/i2c-tegra.c:585:7: got void [noderef] * drivers/i2c/busses/i2c-tegra.c:619:16: warning: incorrect type in assignment (different address spaces) drivers/i2c/busses/i2c-tegra.c:619:16: expected void [noderef] *base drivers/i2c/busses/i2c-tegra.c:619:16: got void *base drivers/i2c/busses/i2c-tegra.c:689:10: warning: incorrect type in argument 1 (different address spaces) drivers/i2c/busses/i2c-tegra.c:689:10: expected void volatile [noderef] *addr drivers/i2c/busses/i2c-tegra.c:689:10: got void *base Signed-off-by: Olof Johansson Acked-by; Stephen Warren Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c index 3c94c4a..b050530 100644 --- a/drivers/i2c/busses/i2c-tegra.c +++ b/drivers/i2c/busses/i2c-tegra.c @@ -566,7 +566,7 @@ static int tegra_i2c_probe(struct platform_device *pdev) struct clk *clk; struct clk *i2c_clk; const unsigned int *prop; - void *base; + void __iomem *base; int irq; int ret = 0; -- cgit v0.10.2 From c5de6467d2a54eb81b139f29b217d0394e8a790c Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Sat, 22 Oct 2011 13:34:36 +0200 Subject: i2c-au1550: remove usage of volatile keyword Replace the usage of "volatile"s with register accessor functions. Signed-off-by: Manuel Lauss Signed-off-by: Ben Dooks diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h b/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h index 892b7f1..5a5cb73 100644 --- a/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h +++ b/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h @@ -394,19 +394,6 @@ typedef struct psc_spi { #define PSC_SPITXRX_LC (1 << 29) #define PSC_SPITXRX_SR (1 << 28) -/* PSC in SMBus (I2C) Mode. */ -typedef struct psc_smb { - u32 psc_sel; - u32 psc_ctrl; - u32 psc_smbcfg; - u32 psc_smbmsk; - u32 psc_smbpcr; - u32 psc_smbstat; - u32 psc_smbevnt; - u32 psc_smbtxrx; - u32 psc_smbtmr; -} psc_smb_t; - /* SMBus Config Register. */ #define PSC_SMBCFG_RT_MASK (3 << 30) #define PSC_SMBCFG_RT_FIFO1 (0 << 30) diff --git a/drivers/i2c/busses/i2c-au1550.c b/drivers/i2c/busses/i2c-au1550.c index 532828b..70b027c 100644 --- a/drivers/i2c/busses/i2c-au1550.c +++ b/drivers/i2c/busses/i2c-au1550.c @@ -39,29 +39,42 @@ #include #include +#define PSC_SEL 0x00 +#define PSC_CTRL 0x04 +#define PSC_SMBCFG 0x08 +#define PSC_SMBMSK 0x0C +#define PSC_SMBPCR 0x10 +#define PSC_SMBSTAT 0x14 +#define PSC_SMBEVNT 0x18 +#define PSC_SMBTXRX 0x1C +#define PSC_SMBTMR 0x20 + struct i2c_au1550_data { - u32 psc_base; + void __iomem *psc_base; int xfer_timeout; int ack_timeout; struct i2c_adapter adap; struct resource *ioarea; }; -static int -wait_xfer_done(struct i2c_au1550_data *adap) +static inline void WR(struct i2c_au1550_data *a, int r, unsigned long v) { - u32 stat; - int i; - volatile psc_smb_t *sp; + __raw_writel(v, a->psc_base + r); + wmb(); +} - sp = (volatile psc_smb_t *)(adap->psc_base); +static inline unsigned long RD(struct i2c_au1550_data *a, int r) +{ + return __raw_readl(a->psc_base + r); +} - /* Wait for Tx Buffer Empty - */ +static int wait_xfer_done(struct i2c_au1550_data *adap) +{ + int i; + + /* Wait for Tx Buffer Empty */ for (i = 0; i < adap->xfer_timeout; i++) { - stat = sp->psc_smbstat; - au_sync(); - if ((stat & PSC_SMBSTAT_TE) != 0) + if (RD(adap, PSC_SMBSTAT) & PSC_SMBSTAT_TE) return 0; udelay(1); @@ -70,41 +83,27 @@ wait_xfer_done(struct i2c_au1550_data *adap) return -ETIMEDOUT; } -static int -wait_ack(struct i2c_au1550_data *adap) +static int wait_ack(struct i2c_au1550_data *adap) { - u32 stat; - volatile psc_smb_t *sp; + unsigned long stat; if (wait_xfer_done(adap)) return -ETIMEDOUT; - sp = (volatile psc_smb_t *)(adap->psc_base); - - stat = sp->psc_smbevnt; - au_sync(); - + stat = RD(adap, PSC_SMBEVNT); if ((stat & (PSC_SMBEVNT_DN | PSC_SMBEVNT_AN | PSC_SMBEVNT_AL)) != 0) return -ETIMEDOUT; return 0; } -static int -wait_master_done(struct i2c_au1550_data *adap) +static int wait_master_done(struct i2c_au1550_data *adap) { - u32 stat; - int i; - volatile psc_smb_t *sp; + int i; - sp = (volatile psc_smb_t *)(adap->psc_base); - - /* Wait for Master Done. - */ + /* Wait for Master Done. */ for (i = 0; i < adap->xfer_timeout; i++) { - stat = sp->psc_smbevnt; - au_sync(); - if ((stat & PSC_SMBEVNT_MD) != 0) + if ((RD(adap, PSC_SMBEVNT) & PSC_SMBEVNT_MD) != 0) return 0; udelay(1); } @@ -115,29 +114,20 @@ wait_master_done(struct i2c_au1550_data *adap) static int do_address(struct i2c_au1550_data *adap, unsigned int addr, int rd, int q) { - volatile psc_smb_t *sp; - u32 stat; + unsigned long stat; - sp = (volatile psc_smb_t *)(adap->psc_base); - - /* Reset the FIFOs, clear events. - */ - stat = sp->psc_smbstat; - sp->psc_smbevnt = PSC_SMBEVNT_ALLCLR; - au_sync(); + /* Reset the FIFOs, clear events. */ + stat = RD(adap, PSC_SMBSTAT); + WR(adap, PSC_SMBEVNT, PSC_SMBEVNT_ALLCLR); if (!(stat & PSC_SMBSTAT_TE) || !(stat & PSC_SMBSTAT_RE)) { - sp->psc_smbpcr = PSC_SMBPCR_DC; - au_sync(); - do { - stat = sp->psc_smbpcr; - au_sync(); - } while ((stat & PSC_SMBPCR_DC) != 0); + WR(adap, PSC_SMBPCR, PSC_SMBPCR_DC); + while ((RD(adap, PSC_SMBPCR) & PSC_SMBPCR_DC) != 0) + cpu_relax(); udelay(50); } - /* Write out the i2c chip address and specify operation - */ + /* Write out the i2c chip address and specify operation */ addr <<= 1; if (rd) addr |= 1; @@ -146,56 +136,42 @@ do_address(struct i2c_au1550_data *adap, unsigned int addr, int rd, int q) if (q) addr |= PSC_SMBTXRX_STP; - /* Put byte into fifo, start up master. - */ - sp->psc_smbtxrx = addr; - au_sync(); - sp->psc_smbpcr = PSC_SMBPCR_MS; - au_sync(); + /* Put byte into fifo, start up master. */ + WR(adap, PSC_SMBTXRX, addr); + WR(adap, PSC_SMBPCR, PSC_SMBPCR_MS); if (wait_ack(adap)) return -EIO; return (q) ? wait_master_done(adap) : 0; } -static u32 -wait_for_rx_byte(struct i2c_au1550_data *adap, u32 *ret_data) +static int wait_for_rx_byte(struct i2c_au1550_data *adap, unsigned char *out) { - int j; - u32 data, stat; - volatile psc_smb_t *sp; + int j; if (wait_xfer_done(adap)) return -EIO; - sp = (volatile psc_smb_t *)(adap->psc_base); - j = adap->xfer_timeout * 100; do { j--; if (j <= 0) return -EIO; - stat = sp->psc_smbstat; - au_sync(); - if ((stat & PSC_SMBSTAT_RE) == 0) + if ((RD(adap, PSC_SMBSTAT) & PSC_SMBSTAT_RE) == 0) j = 0; else udelay(1); } while (j > 0); - data = sp->psc_smbtxrx; - au_sync(); - *ret_data = data; + + *out = RD(adap, PSC_SMBTXRX); return 0; } -static int -i2c_read(struct i2c_au1550_data *adap, unsigned char *buf, +static int i2c_read(struct i2c_au1550_data *adap, unsigned char *buf, unsigned int len) { - int i; - u32 data; - volatile psc_smb_t *sp; + int i; if (len == 0) return 0; @@ -204,62 +180,46 @@ i2c_read(struct i2c_au1550_data *adap, unsigned char *buf, * zero bytes for timing, waiting for bytes to appear in the * receive fifo, then reading the bytes. */ - - sp = (volatile psc_smb_t *)(adap->psc_base); - i = 0; - while (i < (len-1)) { - sp->psc_smbtxrx = 0; - au_sync(); - if (wait_for_rx_byte(adap, &data)) + while (i < (len - 1)) { + WR(adap, PSC_SMBTXRX, 0); + if (wait_for_rx_byte(adap, &buf[i])) return -EIO; - buf[i] = data; i++; } - /* The last byte has to indicate transfer done. - */ - sp->psc_smbtxrx = PSC_SMBTXRX_STP; - au_sync(); + /* The last byte has to indicate transfer done. */ + WR(adap, PSC_SMBTXRX, PSC_SMBTXRX_STP); if (wait_master_done(adap)) return -EIO; - data = sp->psc_smbtxrx; - au_sync(); - buf[i] = data; + buf[i] = (unsigned char)(RD(adap, PSC_SMBTXRX) & 0xff); return 0; } -static int -i2c_write(struct i2c_au1550_data *adap, unsigned char *buf, +static int i2c_write(struct i2c_au1550_data *adap, unsigned char *buf, unsigned int len) { - int i; - u32 data; - volatile psc_smb_t *sp; + int i; + unsigned long data; if (len == 0) return 0; - sp = (volatile psc_smb_t *)(adap->psc_base); - i = 0; while (i < (len-1)) { data = buf[i]; - sp->psc_smbtxrx = data; - au_sync(); + WR(adap, PSC_SMBTXRX, data); if (wait_ack(adap)) return -EIO; i++; } - /* The last byte has to indicate transfer done. - */ + /* The last byte has to indicate transfer done. */ data = buf[i]; data |= PSC_SMBTXRX_STP; - sp->psc_smbtxrx = data; - au_sync(); + WR(adap, PSC_SMBTXRX, data); if (wait_master_done(adap)) return -EIO; return 0; @@ -269,12 +229,10 @@ static int au1550_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, int num) { struct i2c_au1550_data *adap = i2c_adap->algo_data; - volatile psc_smb_t *sp = (volatile psc_smb_t *)adap->psc_base; struct i2c_msg *p; int i, err = 0; - sp->psc_ctrl = PSC_CTRL_ENABLE; - au_sync(); + WR(adap, PSC_CTRL, PSC_CTRL_ENABLE); for (i = 0; !err && i < num; i++) { p = &msgs[i]; @@ -293,14 +251,12 @@ au1550_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, int num) if (err == 0) err = num; - sp->psc_ctrl = PSC_CTRL_SUSPEND; - au_sync(); + WR(adap, PSC_CTRL, PSC_CTRL_SUSPEND); return err; } -static u32 -au1550_func(struct i2c_adapter *adap) +static u32 au1550_func(struct i2c_adapter *adap) { return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; } @@ -312,57 +268,45 @@ static const struct i2c_algorithm au1550_algo = { static void i2c_au1550_setup(struct i2c_au1550_data *priv) { - volatile psc_smb_t *sp = (volatile psc_smb_t *)priv->psc_base; - u32 stat; - - sp->psc_ctrl = PSC_CTRL_DISABLE; - au_sync(); - sp->psc_sel = PSC_SEL_PS_SMBUSMODE; - sp->psc_smbcfg = 0; - au_sync(); - sp->psc_ctrl = PSC_CTRL_ENABLE; - au_sync(); - do { - stat = sp->psc_smbstat; - au_sync(); - } while ((stat & PSC_SMBSTAT_SR) == 0); + unsigned long cfg; - sp->psc_smbcfg = (PSC_SMBCFG_RT_FIFO8 | PSC_SMBCFG_TT_FIFO8 | - PSC_SMBCFG_DD_DISABLE); + WR(priv, PSC_CTRL, PSC_CTRL_DISABLE); + WR(priv, PSC_SEL, PSC_SEL_PS_SMBUSMODE); + WR(priv, PSC_SMBCFG, 0); + WR(priv, PSC_CTRL, PSC_CTRL_ENABLE); + while ((RD(priv, PSC_SMBSTAT) & PSC_SMBSTAT_SR) == 0) + cpu_relax(); + + cfg = PSC_SMBCFG_RT_FIFO8 | PSC_SMBCFG_TT_FIFO8 | PSC_SMBCFG_DD_DISABLE; + WR(priv, PSC_SMBCFG, cfg); /* Divide by 8 to get a 6.25 MHz clock. The later protocol * timings are based on this clock. */ - sp->psc_smbcfg |= PSC_SMBCFG_SET_DIV(PSC_SMBCFG_DIV8); - sp->psc_smbmsk = PSC_SMBMSK_ALLMASK; - au_sync(); + cfg |= PSC_SMBCFG_SET_DIV(PSC_SMBCFG_DIV8); + WR(priv, PSC_SMBCFG, cfg); + WR(priv, PSC_SMBMSK, PSC_SMBMSK_ALLMASK); /* Set the protocol timer values. See Table 71 in the * Au1550 Data Book for standard timing values. */ - sp->psc_smbtmr = PSC_SMBTMR_SET_TH(0) | PSC_SMBTMR_SET_PS(15) | \ + WR(priv, PSC_SMBTMR, PSC_SMBTMR_SET_TH(0) | PSC_SMBTMR_SET_PS(15) | \ PSC_SMBTMR_SET_PU(15) | PSC_SMBTMR_SET_SH(15) | \ PSC_SMBTMR_SET_SU(15) | PSC_SMBTMR_SET_CL(15) | \ - PSC_SMBTMR_SET_CH(15); - au_sync(); + PSC_SMBTMR_SET_CH(15)); - sp->psc_smbcfg |= PSC_SMBCFG_DE_ENABLE; - do { - stat = sp->psc_smbstat; - au_sync(); - } while ((stat & PSC_SMBSTAT_SR) == 0); + cfg |= PSC_SMBCFG_DE_ENABLE; + WR(priv, PSC_SMBCFG, cfg); + while ((RD(priv, PSC_SMBSTAT) & PSC_SMBSTAT_SR) == 0) + cpu_relax(); - sp->psc_ctrl = PSC_CTRL_SUSPEND; - au_sync(); + WR(priv, PSC_CTRL, PSC_CTRL_SUSPEND); } static void i2c_au1550_disable(struct i2c_au1550_data *priv) { - volatile psc_smb_t *sp = (volatile psc_smb_t *)priv->psc_base; - - sp->psc_smbcfg = 0; - sp->psc_ctrl = PSC_CTRL_DISABLE; - au_sync(); + WR(priv, PSC_SMBCFG, 0); + WR(priv, PSC_CTRL, PSC_CTRL_DISABLE); } /* @@ -396,7 +340,11 @@ i2c_au1550_probe(struct platform_device *pdev) goto out_mem; } - priv->psc_base = CKSEG1ADDR(r->start); + priv->psc_base = ioremap(r->start, resource_size(r)); + if (!priv->psc_base) { + ret = -EIO; + goto out_map; + } priv->xfer_timeout = 200; priv->ack_timeout = 200; @@ -406,8 +354,7 @@ i2c_au1550_probe(struct platform_device *pdev) priv->adap.dev.parent = &pdev->dev; strlcpy(priv->adap.name, "Au1xxx PSC I2C", sizeof(priv->adap.name)); - /* Now, set up the PSC for SMBus PIO mode. - */ + /* Now, set up the PSC for SMBus PIO mode. */ i2c_au1550_setup(priv); ret = i2c_add_numbered_adapter(&priv->adap); @@ -417,7 +364,8 @@ i2c_au1550_probe(struct platform_device *pdev) } i2c_au1550_disable(priv); - + iounmap(priv->psc_base); +out_map: release_resource(priv->ioarea); kfree(priv->ioarea); out_mem: @@ -426,14 +374,14 @@ out: return ret; } -static int __devexit -i2c_au1550_remove(struct platform_device *pdev) +static int __devexit i2c_au1550_remove(struct platform_device *pdev) { struct i2c_au1550_data *priv = platform_get_drvdata(pdev); platform_set_drvdata(pdev, NULL); i2c_del_adapter(&priv->adap); i2c_au1550_disable(priv); + iounmap(priv->psc_base); release_resource(priv->ioarea); kfree(priv->ioarea); kfree(priv); @@ -476,14 +424,12 @@ static struct platform_driver au1xpsc_smbus_driver = { .resume = i2c_au1550_resume, }; -static int __init -i2c_au1550_init(void) +static int __init i2c_au1550_init(void) { return platform_driver_register(&au1xpsc_smbus_driver); } -static void __exit -i2c_au1550_exit(void) +static void __exit i2c_au1550_exit(void) { platform_driver_unregister(&au1xpsc_smbus_driver); } -- cgit v0.10.2 From 85ea25698843d37b6f79927b2995644623fe1e06 Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Sat, 22 Oct 2011 13:34:37 +0200 Subject: i2c-au1550: remove unused ack_timeout The ack_timeout context member is unused, get rid of it. Signed-off-by: Manuel Lauss Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-au1550.c b/drivers/i2c/busses/i2c-au1550.c index 70b027c..98ee11a 100644 --- a/drivers/i2c/busses/i2c-au1550.c +++ b/drivers/i2c/busses/i2c-au1550.c @@ -52,7 +52,6 @@ struct i2c_au1550_data { void __iomem *psc_base; int xfer_timeout; - int ack_timeout; struct i2c_adapter adap; struct resource *ioarea; }; @@ -346,7 +345,6 @@ i2c_au1550_probe(struct platform_device *pdev) goto out_map; } priv->xfer_timeout = 200; - priv->ack_timeout = 200; priv->adap.nr = pdev->id; priv->adap.algo = &au1550_algo; -- cgit v0.10.2 From 84785f120f4d64c5fa8cf4bab1cf07c2507d434f Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Sat, 22 Oct 2011 13:34:38 +0200 Subject: i2c-au1550: increase timeout waiting for master done Double the timeout in the loop which busy-waits for the "master-done" bit to be set. This bit indicates whether an i2c transaction has completed; on the DB1300 and DB1550 boards this timeout is slightly too short and causes transactions to the WM8731 codec to be falsely flagged as failed. The timeout itself is necessary since transactions to non-existant slaves never set this bit in the first place (and cause i2cdetect to hang). With this change the WM8731 codec on the DB1300/DB1550 boards is correctly detected and initialized. Signed-off-by: Manuel Lauss Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-au1550.c b/drivers/i2c/busses/i2c-au1550.c index 98ee11a..4f5150c 100644 --- a/drivers/i2c/busses/i2c-au1550.c +++ b/drivers/i2c/busses/i2c-au1550.c @@ -101,7 +101,7 @@ static int wait_master_done(struct i2c_au1550_data *adap) int i; /* Wait for Master Done. */ - for (i = 0; i < adap->xfer_timeout; i++) { + for (i = 0; i < 2 * adap->xfer_timeout; i++) { if ((RD(adap, PSC_SMBEVNT) & PSC_SMBEVNT_MD) != 0) return 0; udelay(1); -- cgit v0.10.2 From 46f344e2a0844d9b068bffa38cb48b52f4bd2d4a Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Sat, 22 Oct 2011 13:34:39 +0200 Subject: i2c-au1550: dev_pm_ops conversion use newer dev_pm_ops for PM Signed-off-by: Manuel Lauss Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-au1550.c b/drivers/i2c/busses/i2c-au1550.c index 4f5150c..4f757a2 100644 --- a/drivers/i2c/busses/i2c-au1550.c +++ b/drivers/i2c/busses/i2c-au1550.c @@ -387,39 +387,43 @@ static int __devexit i2c_au1550_remove(struct platform_device *pdev) } #ifdef CONFIG_PM -static int -i2c_au1550_suspend(struct platform_device *pdev, pm_message_t state) +static int i2c_au1550_suspend(struct device *dev) { - struct i2c_au1550_data *priv = platform_get_drvdata(pdev); + struct i2c_au1550_data *priv = dev_get_drvdata(dev); i2c_au1550_disable(priv); return 0; } -static int -i2c_au1550_resume(struct platform_device *pdev) +static int i2c_au1550_resume(struct device *dev) { - struct i2c_au1550_data *priv = platform_get_drvdata(pdev); + struct i2c_au1550_data *priv = dev_get_drvdata(dev); i2c_au1550_setup(priv); return 0; } + +static const struct dev_pm_ops i2c_au1550_pmops = { + .suspend = i2c_au1550_suspend, + .resume = i2c_au1550_resume, +}; + +#define AU1XPSC_SMBUS_PMOPS (&i2c_au1550_pmops) + #else -#define i2c_au1550_suspend NULL -#define i2c_au1550_resume NULL +#define AU1XPSC_SMBUS_PMOPS NULL #endif static struct platform_driver au1xpsc_smbus_driver = { .driver = { .name = "au1xpsc_smbus", .owner = THIS_MODULE, + .pm = AU1XPSC_SMBUS_PMOPS, }, .probe = i2c_au1550_probe, .remove = __devexit_p(i2c_au1550_remove), - .suspend = i2c_au1550_suspend, - .resume = i2c_au1550_resume, }; static int __init i2c_au1550_init(void) -- cgit v0.10.2 From 8abf6fbbd22bc777fd4027cbc55e99cdfb7a8324 Mon Sep 17 00:00:00 2001 From: Jonas Aaberg Date: Thu, 20 Oct 2011 18:23:01 +0200 Subject: i2c-nomadik: cosmetic coding style corrections This fixes a number of whitespace and punctuation problems around the Nomadik I2C driver. Signed-off-by: Jonas Aaberg Signed-off-by: Linus Walleij Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c index b228e09..ce4fd80 100644 --- a/drivers/i2c/busses/i2c-nomadik.c +++ b/drivers/i2c/busses/i2c-nomadik.c @@ -63,11 +63,11 @@ /* Master controller (MCR) register */ #define I2C_MCR_OP (0x1 << 0) /* Operation */ #define I2C_MCR_A7 (0x7f << 1) /* 7-bit address */ -#define I2C_MCR_EA10 (0x7 << 8) /* 10-bit Extended address */ +#define I2C_MCR_EA10 (0x7 << 8) /* 10-bit Extended address */ #define I2C_MCR_SB (0x1 << 11) /* Extended address */ #define I2C_MCR_AM (0x3 << 12) /* Address type */ -#define I2C_MCR_STOP (0x1 << 14) /* Stop condition */ -#define I2C_MCR_LENGTH (0x7ff << 15) /* Transaction length */ +#define I2C_MCR_STOP (0x1 << 14) /* Stop condition */ +#define I2C_MCR_LENGTH (0x7ff << 15) /* Transaction length */ /* Status register (SR) */ #define I2C_SR_OP (0x3 << 0) /* Operation */ @@ -77,7 +77,7 @@ #define I2C_SR_LENGTH (0x7ff << 9) /* Transfer length */ /* Interrupt mask set/clear (IMSCR) bits */ -#define I2C_IT_TXFE (0x1 << 0) +#define I2C_IT_TXFE (0x1 << 0) #define I2C_IT_TXFNE (0x1 << 1) #define I2C_IT_TXFF (0x1 << 2) #define I2C_IT_TXFOVR (0x1 << 3) @@ -135,31 +135,31 @@ struct i2c_nmk_client { }; /** - * struct nmk_i2c_dev - private data structure of the controller - * @pdev: parent platform device - * @adap: corresponding I2C adapter - * @irq: interrupt line for the controller - * @virtbase: virtual io memory area - * @clk: hardware i2c block clock - * @cfg: machine provided controller configuration - * @cli: holder of client specific data - * @stop: stop condition - * @xfer_complete: acknowledge completion for a I2C message - * @result: controller propogated result - * @regulator: pointer to i2c regulator - * @busy: Busy doing transfer + * struct nmk_i2c_dev - private data structure of the controller. + * @pdev: parent platform device. + * @adap: corresponding I2C adapter. + * @irq: interrupt line for the controller. + * @virtbase: virtual io memory area. + * @clk: hardware i2c block clock. + * @cfg: machine provided controller configuration. + * @cli: holder of client specific data. + * @stop: stop condition. + * @xfer_complete: acknowledge completion for a I2C message. + * @result: controller propogated result. + * @regulator: pointer to i2c regulator. + * @busy: Busy doing transfer. */ struct nmk_i2c_dev { struct platform_device *pdev; - struct i2c_adapter adap; - int irq; + struct i2c_adapter adap; + int irq; void __iomem *virtbase; struct clk *clk; struct nmk_i2c_controller cfg; struct i2c_nmk_client cli; - int stop; + int stop; struct completion xfer_complete; - int result; + int result; struct regulator *regulator; bool busy; }; @@ -217,8 +217,9 @@ static int flush_i2c_fifo(struct nmk_i2c_dev *dev) } } - dev_err(&dev->pdev->dev, "flushing operation timed out " - "giving up after %d attempts", LOOP_ATTEMPTS); + dev_err(&dev->pdev->dev, + "flushing operation timed out giving up after %d attempts", + LOOP_ATTEMPTS); return -ETIMEDOUT; } @@ -270,7 +271,7 @@ exit: } /* enable peripheral, master mode operation */ -#define DEFAULT_I2C_REG_CR ((1 << 1) | I2C_CR_PE) +#define DEFAULT_I2C_REG_CR ((1 << 1) | I2C_CR_PE) /** * load_i2c_mcr_reg() - load the MCR register @@ -363,8 +364,8 @@ static void setup_i2c_controller(struct nmk_i2c_dev *dev) * and high speed (up to 3.4 Mb/s) */ if (dev->cfg.sm > I2C_FREQ_MODE_FAST) { - dev_err(&dev->pdev->dev, "do not support this mode " - "defaulting to std. mode\n"); + dev_err(&dev->pdev->dev, + "do not support this mode defaulting to std. mode\n"); brcr2 = i2c_clk/(100000 * 2) & 0xffff; writel((brcr1 | brcr2), dev->virtbase + I2C_BRCR); writel(I2C_FREQ_MODE_STANDARD << 4, @@ -423,7 +424,7 @@ static int read_i2c(struct nmk_i2c_dev *dev) if (timeout < 0) { dev_err(&dev->pdev->dev, - "wait_for_completion_timeout" + "wait_for_completion_timeout " "returned %d waiting for event\n", timeout); status = timeout; } @@ -556,8 +557,8 @@ static int nmk_i2c_xfer_one(struct nmk_i2c_dev *dev, u16 flags) if (((i2c_sr >> 2) & 0x3) == 0x3) { /* get the abort cause */ cause = (i2c_sr >> 4) & 0x7; - dev_err(&dev->pdev->dev, "%s\n", cause - >= ARRAY_SIZE(abort_causes) ? + dev_err(&dev->pdev->dev, "%s\n", + cause >= ARRAY_SIZE(abort_causes) ? "unknown reason" : abort_causes[cause]); } @@ -582,13 +583,13 @@ static int nmk_i2c_xfer_one(struct nmk_i2c_dev *dev, u16 flags) * * NOTE: * READ TRANSFER : We impose a restriction of the first message to be the - * index message for any read transaction. - * - a no index is coded as '0', - * - 2byte big endian index is coded as '3' - * !!! msg[0].buf holds the actual index. - * This is compatible with generic messages of smbus emulator - * that send a one byte index. - * eg. a I2C transation to read 2 bytes from index 0 + * index message for any read transaction. + * - a no index is coded as '0', + * - 2byte big endian index is coded as '3' + * !!! msg[0].buf holds the actual index. + * This is compatible with generic messages of smbus emulator + * that send a one byte index. + * eg. a I2C transation to read 2 bytes from index 0 * idx = 0; * msg[0].addr = client->addr; * msg[0].flags = 0x0; @@ -644,8 +645,8 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap, for (i = 0; i < num_msgs; i++) { if (unlikely(msgs[i].flags & I2C_M_TEN)) { - dev_err(&dev->pdev->dev, "10 bit addressing" - "not supported\n"); + dev_err(&dev->pdev->dev, + "10 bit addressing not supported\n"); status = -EINVAL; goto out; @@ -789,8 +790,9 @@ static irqreturn_t i2c_irq_handler(int irq, void *arg) if (dev->cli.count) { dev->result = -EIO; - dev_err(&dev->pdev->dev, "%lu bytes still remain to be" - "xfered\n", dev->cli.count); + dev_err(&dev->pdev->dev, + "%lu bytes still remain to be xfered\n", + dev->cli.count); (void) init_hw(dev); } complete(&dev->xfer_complete); @@ -923,7 +925,7 @@ static int __devinit nmk_i2c_probe(struct platform_device *pdev) } if (request_mem_region(res->start, resource_size(res), - DRIVER_NAME "I/O region") == NULL) { + DRIVER_NAME "I/O region") == NULL) { ret = -EBUSY; goto err_no_region; } @@ -980,8 +982,9 @@ static int __devinit nmk_i2c_probe(struct platform_device *pdev) i2c_set_adapdata(adap, dev); - dev_info(&pdev->dev, "initialize %s on virtual " - "base %p\n", adap->name, dev->virtbase); + dev_info(&pdev->dev, + "initialize %s on virtual base %p\n", + adap->name, dev->virtbase); ret = i2c_add_numbered_adapter(adap); if (ret) { -- cgit v0.10.2 From 4fd81eb2d64295ab038a3ea9d44e0eac85a6648c Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Tue, 13 Sep 2011 09:46:04 +0530 Subject: i2c-s3c2410: Keep a copy of platform data and use it The platform data is copied into driver's private data and the copy is used for all access to the platform data. This simpifies the addition of device tree support for the i2c-s3c2410 driver. Cc: Ben Dooks Signed-off-by: Thomas Abraham Acked-by: Grant Likely Signed-off-by: Ben Dooks diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index f84a63c..266dd83 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -78,6 +78,7 @@ struct s3c24xx_i2c { struct resource *ioarea; struct i2c_adapter adap; + struct s3c2410_platform_i2c *pdata; #ifdef CONFIG_CPU_FREQ struct notifier_block freq_transition; #endif @@ -625,7 +626,7 @@ static int s3c24xx_i2c_calcdivisor(unsigned long clkin, unsigned int wanted, static int s3c24xx_i2c_clockrate(struct s3c24xx_i2c *i2c, unsigned int *got) { - struct s3c2410_platform_i2c *pdata = i2c->dev->platform_data; + struct s3c2410_platform_i2c *pdata = i2c->pdata; unsigned long clkin = clk_get_rate(i2c->clk); unsigned int divs, div1; unsigned long target_frequency; @@ -754,7 +755,7 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) /* get the plafrom data */ - pdata = i2c->dev->platform_data; + pdata = i2c->pdata; /* inititalise the gpio */ @@ -793,7 +794,7 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) static int s3c24xx_i2c_probe(struct platform_device *pdev) { struct s3c24xx_i2c *i2c; - struct s3c2410_platform_i2c *pdata; + struct s3c2410_platform_i2c *pdata = NULL; struct resource *res; int ret; @@ -809,6 +810,15 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev) return -ENOMEM; } + i2c->pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!i2c->pdata) { + ret = -ENOMEM; + goto err_noclk; + } + + if (pdata) + memcpy(i2c->pdata, pdata, sizeof(*pdata)); + strlcpy(i2c->adap.name, "s3c2410-i2c", sizeof(i2c->adap.name)); i2c->adap.owner = THIS_MODULE; i2c->adap.algo = &s3c24xx_i2c_algorithm; @@ -903,7 +913,7 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev) * being bus 0. */ - i2c->adap.nr = pdata->bus_num; + i2c->adap.nr = i2c->pdata->bus_num; ret = i2c_add_numbered_adapter(&i2c->adap); if (ret < 0) { -- cgit v0.10.2 From 5a5f50802f5a31b9e15de8df40d5621af970a560 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Tue, 13 Sep 2011 09:46:05 +0530 Subject: i2c-s3c2410: Add device tree support Add device tree probe support for Samsung's s3c2410 i2c driver. Cc: Ben Dooks Signed-off-by: Thomas Abraham Acked-by: Grant Likely Signed-off-by: Ben Dooks diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt new file mode 100644 index 0000000..38832c7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt @@ -0,0 +1,39 @@ +* Samsung's I2C controller + +The Samsung's I2C controller is used to interface with I2C devices. + +Required properties: + - compatible: value should be either of the following. + (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c. + (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. + - gpios: The order of the gpios should be the following: . + The gpio specifier depends on the gpio controller. + +Optional properties: + - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not + specified, default value is 0. + - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not + specified, the default value in Hz is 100000. + +Example: + + i2c@13870000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x13870000 0x100>; + interrupts = <345>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <100000>; + gpios = <&gpd1 2 0 /* SDA */ + &gpd1 3 0 /* SCL */>; + #address-cells = <1>; + #size-cells = <0>; + + wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; + }; + }; diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index 266dd83..9c00ad1 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -35,6 +35,8 @@ #include #include #include +#include +#include #include @@ -79,6 +81,7 @@ struct s3c24xx_i2c { struct i2c_adapter adap; struct s3c2410_platform_i2c *pdata; + int gpios[2]; #ifdef CONFIG_CPU_FREQ struct notifier_block freq_transition; #endif @@ -96,6 +99,12 @@ static inline int s3c24xx_i2c_is2440(struct s3c24xx_i2c *i2c) struct platform_device *pdev = to_platform_device(i2c->dev); enum s3c24xx_i2c_type type; +#ifdef CONFIG_OF + if (i2c->dev->of_node) + return of_device_is_compatible(i2c->dev->of_node, + "samsung,s3c2440-i2c"); +#endif + type = platform_get_device_id(pdev)->driver_data; return type == TYPE_S3C2440; } @@ -742,6 +751,49 @@ static inline void s3c24xx_i2c_deregister_cpufreq(struct s3c24xx_i2c *i2c) } #endif +#ifdef CONFIG_OF +static int s3c24xx_i2c_parse_dt_gpio(struct s3c24xx_i2c *i2c) +{ + int idx, gpio, ret; + + for (idx = 0; idx < 2; idx++) { + gpio = of_get_gpio(i2c->dev->of_node, idx); + if (!gpio_is_valid(gpio)) { + dev_err(i2c->dev, "invalid gpio[%d]: %d\n", idx, gpio); + goto free_gpio; + } + + ret = gpio_request(gpio, "i2c-bus"); + if (ret) { + dev_err(i2c->dev, "gpio [%d] request failed\n", gpio); + goto free_gpio; + } + } + return 0; + +free_gpio: + while (--idx >= 0) + gpio_free(i2c->gpios[idx]); + return -EINVAL; +} + +static void s3c24xx_i2c_dt_gpio_free(struct s3c24xx_i2c *i2c) +{ + unsigned int idx; + for (idx = 0; idx < 2; idx++) + gpio_free(i2c->gpios[idx]); +} +#else +static int s3c24xx_i2c_parse_dt_gpio(struct s3c24xx_i2c *i2c) +{ + return -EINVAL; +} + +static void s3c24xx_i2c_dt_gpio_free(struct s3c24xx_i2c *i2c) +{ +} +#endif + /* s3c24xx_i2c_init * * initialise the controller, set the IO lines and frequency @@ -761,6 +813,9 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) if (pdata->cfg_gpio) pdata->cfg_gpio(to_platform_device(i2c->dev)); + else + if (s3c24xx_i2c_parse_dt_gpio(i2c)) + return -EINVAL; /* write slave address */ @@ -786,6 +841,34 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c) return 0; } +#ifdef CONFIG_OF +/* s3c24xx_i2c_parse_dt + * + * Parse the device tree node and retreive the platform data. +*/ + +static void +s3c24xx_i2c_parse_dt(struct device_node *np, struct s3c24xx_i2c *i2c) +{ + struct s3c2410_platform_i2c *pdata = i2c->pdata; + + if (!np) + return; + + pdata->bus_num = -1; /* i2c bus number is dynamically assigned */ + of_property_read_u32(np, "samsung,i2c-sda-delay", &pdata->sda_delay); + of_property_read_u32(np, "samsung,i2c-slave-addr", &pdata->slave_addr); + of_property_read_u32(np, "samsung,i2c-max-bus-freq", + (u32 *)&pdata->frequency); +} +#else +static void +s3c24xx_i2c_parse_dt(struct device_node *np, struct s3c24xx_i2c *i2c) +{ + return; +} +#endif + /* s3c24xx_i2c_probe * * called by the bus driver when a suitable device is found @@ -798,10 +881,12 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev) struct resource *res; int ret; - pdata = pdev->dev.platform_data; - if (!pdata) { - dev_err(&pdev->dev, "no platform data\n"); - return -EINVAL; + if (!pdev->dev.of_node) { + pdata = pdev->dev.platform_data; + if (!pdata) { + dev_err(&pdev->dev, "no platform data\n"); + return -EINVAL; + } } i2c = kzalloc(sizeof(struct s3c24xx_i2c), GFP_KERNEL); @@ -818,6 +903,8 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev) if (pdata) memcpy(i2c->pdata, pdata, sizeof(*pdata)); + else + s3c24xx_i2c_parse_dt(pdev->dev.of_node, i2c); strlcpy(i2c->adap.name, "s3c2410-i2c", sizeof(i2c->adap.name)); i2c->adap.owner = THIS_MODULE; @@ -914,6 +1001,7 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev) */ i2c->adap.nr = i2c->pdata->bus_num; + i2c->adap.dev.of_node = pdev->dev.of_node; ret = i2c_add_numbered_adapter(&i2c->adap); if (ret < 0) { @@ -921,6 +1009,7 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev) goto err_cpufreq; } + of_i2c_register_devices(&i2c->adap); platform_set_drvdata(pdev, i2c); dev_info(&pdev->dev, "%s: S3C I2C adapter\n", dev_name(&i2c->adap.dev)); @@ -969,6 +1058,7 @@ static int s3c24xx_i2c_remove(struct platform_device *pdev) iounmap(i2c->regs); release_resource(i2c->ioarea); + s3c24xx_i2c_dt_gpio_free(i2c); kfree(i2c->ioarea); kfree(i2c); @@ -1022,6 +1112,17 @@ static struct platform_device_id s3c24xx_driver_ids[] = { }; MODULE_DEVICE_TABLE(platform, s3c24xx_driver_ids); +#ifdef CONFIG_OF +static const struct of_device_id s3c24xx_i2c_match[] = { + { .compatible = "samsung,s3c2410-i2c" }, + { .compatible = "samsung,s3c2440-i2c" }, + {}, +}; +MODULE_DEVICE_TABLE(of, s3c24xx_i2c_match); +#else +#define s3c24xx_i2c_match NULL +#endif + static struct platform_driver s3c24xx_i2c_driver = { .probe = s3c24xx_i2c_probe, .remove = s3c24xx_i2c_remove, @@ -1030,6 +1131,7 @@ static struct platform_driver s3c24xx_i2c_driver = { .owner = THIS_MODULE, .name = "s3c-i2c", .pm = S3C24XX_DEV_PM_OPS, + .of_match_table = s3c24xx_i2c_match, }, }; -- cgit v0.10.2