From ab85b120e6925203e4b63022166eacac19009380 Mon Sep 17 00:00:00 2001 From: Samuel Ortiz Date: Tue, 9 Apr 2013 14:40:09 +0200 Subject: mfd: Kconfig alphabetical re-ordering Ordering so many Kconfig alphabetically makes it a lot easier to read e.g. from menuconfig. Signed-off-by: Samuel Ortiz diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 9d64e32..2f3ce18 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -10,19 +10,45 @@ config MFD_CORE select IRQ_DOMAIN default n -config MFD_88PM860X - bool "Support Marvell 88PM8606/88PM8607" - depends on I2C=y && GENERIC_HARDIRQS +config MFD_CS5535 + tristate "AMD CS5535 and CS5536 southbridge core functions" + select MFD_CORE + depends on PCI && X86 + ---help--- + This is the core driver for CS5535/CS5536 MFD functions. This is + necessary for using the board's GPIO and MFGPT functionality. + +config MFD_AS3711 + bool "AMS AS3711" + select MFD_CORE select REGMAP_I2C + select REGMAP_IRQ + depends on I2C=y && GENERIC_HARDIRQS + help + Support for the AS3711 PMIC from AMS + +config PMIC_ADP5520 + bool "Analog Devices ADP5520/01 MFD PMIC Core Support" + depends on I2C=y + help + Say yes here to add support for Analog Devices AD5520 and ADP5501, + Multifunction Power Management IC. This includes + the I2C driver and the core APIs _only_, you have to select + individual components like LCD backlight, LEDs, GPIOs and Kepad + under the corresponding menus. + +config MFD_AAT2870_CORE + bool "AnalogicTech AAT2870" select MFD_CORE + depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS help - This supports for Marvell 88PM8606/88PM8607 Power Management IC. - This includes the I2C driver and the core APIs _only_, you have to - select individual components like voltage regulators, RTC and - battery-charger under the corresponding menus. + If you say yes here you get support for the AAT2870. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the + functionality of the device. config MFD_CROS_EC - tristate "Support ChromeOS Embedded Controller" + tristate "ChromeOS Embedded Controller" select MFD_CORE help If you say Y here you get support for the ChromeOS Embedded @@ -50,100 +76,98 @@ config MFD_CROS_EC_SPI response time cannot be guaranteed, we support ignoring 'pre-amble' bytes before the response actually starts. -config MFD_88PM800 - tristate "Support Marvell 88PM800" - depends on I2C=y && GENERIC_HARDIRQS - select REGMAP_I2C - select REGMAP_IRQ +config MFD_ASIC3 + bool "Compaq ASIC3" + depends on GENERIC_HARDIRQS && GPIOLIB && ARM select MFD_CORE + ---help--- + This driver supports the ASIC3 multifunction chip found on many + PDAs (mainly iPAQ and HTC based ones) + +config PMIC_DA903X + bool "Dialog Semiconductor DA9030/DA9034 PMIC Support" + depends on I2C=y help - This supports for Marvell 88PM800 Power Management IC. - This includes the I2C driver and the core APIs _only_, you have to - select individual components like voltage regulators, RTC and - battery-charger under the corresponding menus. + Say yes here to support for Dialog Semiconductor DA9030 (a.k.a + ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC + usually found on PXA processors-based platforms. This includes + the I2C driver and the core APIs _only_, you have to select + individual components like LCD backlight, voltage regulators, + LEDs and battery-charger under the corresponding menus. -config MFD_88PM805 - tristate "Support Marvell 88PM805" - depends on I2C=y && GENERIC_HARDIRQS - select REGMAP_I2C - select REGMAP_IRQ +config PMIC_DA9052 + bool select MFD_CORE - help - This supports for Marvell 88PM805 Power Management IC. This includes - the I2C driver and the core APIs _only_, you have to select individual - components like codec device, headset/Mic device under the - corresponding menus. -config MFD_SM501 - tristate "Support for Silicon Motion SM501" - ---help--- - This is the core driver for the Silicon Motion SM501 multimedia - companion chip. This device is a multifunction device which may - provide numerous interfaces including USB host controller, USB gadget, - asynchronous serial ports, audio functions, and a dual display video - interface. The device may be connected by PCI or local bus with - varying functions enabled. +config MFD_DA9052_SPI + bool "Dialog Semiconductor DA9052/53 PMIC variants with SPI" + select REGMAP_SPI + select REGMAP_IRQ + select PMIC_DA9052 + depends on SPI_MASTER=y && GENERIC_HARDIRQS + help + Support for the Dialog Semiconductor DA9052 PMIC + when controlled using SPI. This driver provides common support + for accessing the device, additional drivers must be enabled in + order to use the functionality of the device. -config MFD_SM501_GPIO - bool "Export GPIO via GPIO layer" - depends on MFD_SM501 && GPIOLIB - ---help--- - This option uses the gpio library layer to export the 64 GPIO - lines on the SM501. The platform data is used to supply the - base number for the first GPIO line to register. +config MFD_DA9052_I2C + bool "Dialog Semiconductor DA9052/53 PMIC variants with I2C" + select REGMAP_I2C + select REGMAP_IRQ + select PMIC_DA9052 + depends on I2C=y && GENERIC_HARDIRQS + help + Support for the Dialog Semiconductor DA9052 PMIC + when controlled using I2C. This driver provides common support + for accessing the device, additional drivers must be enabled in + order to use the functionality of the device. -config MFD_RTSX_PCI - tristate "Support for Realtek PCI-E card reader" - depends on PCI && GENERIC_HARDIRQS +config MFD_DA9055 + bool "Dialog Semiconductor DA9055 PMIC Support" + select REGMAP_I2C + select REGMAP_IRQ select MFD_CORE + depends on I2C=y && GENERIC_HARDIRQS help - This supports for Realtek PCI-Express card reader including rts5209, - rts5229, rtl8411, etc. Realtek card reader supports access to many - types of memory cards, such as Memory Stick, Memory Stick Pro, - Secure Digital and MultiMediaCard. + Say yes here for support of Dialog Semiconductor DA9055. This is + a Power Management IC. This driver provides common support for + accessing the device as well as the I2C interface to the chip itself. + Additional drivers must be enabled in order to use the functionality + of the device. -config MFD_ASIC3 - bool "Support for Compaq ASIC3" - depends on GENERIC_HARDIRQS && GPIOLIB && ARM - select MFD_CORE - ---help--- - This driver supports the ASIC3 multifunction chip found on many - PDAs (mainly iPAQ and HTC based ones) + This driver can be built as a module. If built as a module it will be + called "da9055" -config MFD_DAVINCI_VOICECODEC +config MFD_MC13783 tristate - select MFD_CORE - -config MFD_DM355EVM_MSP - bool "DaVinci DM355 EVM microcontroller" - depends on I2C=y && MACH_DAVINCI_DM355_EVM - help - This driver supports the MSP430 microcontroller used on these - boards. MSP430 firmware manages resets and power sequencing, - inputs from buttons and the IR remote, LEDs, an RTC, and more. -config MFD_TI_SSP - tristate "TI Sequencer Serial Port support" - depends on ARCH_DAVINCI_TNETV107X && GENERIC_HARDIRQS +config MFD_MC13XXX + tristate + depends on (SPI_MASTER || I2C) && GENERIC_HARDIRQS select MFD_CORE - ---help--- - Say Y here if you want support for the Sequencer Serial Port - in a Texas Instruments TNETV107X SoC. + select MFD_MC13783 + help + Enable support for the Freescale MC13783 and MC13892 PMICs. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the + functionality of the device. - To compile this driver as a module, choose M here: the - module will be called ti-ssp. +config MFD_MC13XXX_SPI + tristate "Freescale MC13783 and MC13892 SPI interface" + depends on SPI_MASTER && GENERIC_HARDIRQS + select REGMAP_SPI + select MFD_MC13XXX + help + Select this if your MC13xxx is connected via an SPI bus. -config MFD_TI_AM335X_TSCADC - tristate "TI ADC / Touch Screen chip support" - select MFD_CORE - select REGMAP - select REGMAP_MMIO - depends on GENERIC_HARDIRQS +config MFD_MC13XXX_I2C + tristate "Freescale MC13892 I2C interface" + depends on I2C && GENERIC_HARDIRQS + select REGMAP_I2C + select MFD_MC13XXX help - If you say yes here you get support for Texas Instruments series - of Touch Screen /ADC chips. - To compile this driver as a module, choose M here: the - module will be called ti_am335x_tscadc. + Select this if your MC13xxx is connected via an I2C bus. config HTC_EGPIO bool "HTC EGPIO support" @@ -172,281 +196,317 @@ config HTC_I2CPLD This device provides input and output GPIOs through an I2C interface to one or more sub-chips. -config UCB1400_CORE - tristate "Philips UCB1400 Core driver" - depends on AC97_BUS - depends on GPIOLIB +config LPC_ICH + tristate "Intel ICH LPC" + depends on PCI && GENERIC_HARDIRQS + select MFD_CORE help - This enables support for the Philips UCB1400 core functions. - The UCB1400 is an AC97 audio codec. - - To compile this driver as a module, choose M here: the - module will be called ucb1400_core. + The LPC bridge function of the Intel ICH provides support for + many functional units. This driver provides needed support for + other drivers to control these functions, currently GPIO and + watchdog. -config MFD_LM3533 - tristate "LM3533 Lighting Power chip" - depends on I2C +config LPC_SCH + tristate "Intel SCH LPC" + depends on PCI && GENERIC_HARDIRQS select MFD_CORE - select REGMAP_I2C - depends on GENERIC_HARDIRQS help - Say yes here to enable support for National Semiconductor / TI - LM3533 Lighting Power chips. - - This driver provides common support for accessing the device; - additional drivers must be enabled in order to use the LED, - backlight or ambient-light-sensor functionality of the device. + LPC bridge function of the Intel SCH provides support for + System Management Bus and General Purpose I/O. -config TPS6105X - tristate "TPS61050/61052 Boost Converters" - depends on I2C - select REGULATOR +config MFD_INTEL_MSIC + bool "Intel MSIC" + depends on INTEL_SCU_IPC select MFD_CORE - select REGULATOR_FIXED_VOLTAGE - depends on GENERIC_HARDIRQS help - This option enables a driver for the TP61050/TPS61052 - high-power "white LED driver". This boost converter is - sometimes used for other things than white LEDs, and - also contains a GPIO pin. + Select this option to enable access to Intel MSIC (Avatele + Passage) chip. This chip embeds audio, battery, GPIO, etc. + devices used in Intel Medfield platforms. -config TPS65010 - tristate "TPS6501x Power Management chips" - depends on I2C && GPIOLIB - default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK +config MFD_JANZ_CMODIO + tristate "Janz CMOD-IO PCI MODULbus Carrier Board" + select MFD_CORE + depends on PCI && GENERIC_HARDIRQS help - If you say yes here you get support for the TPS6501x series of - Power Management chips. These include voltage regulators, - lithium ion/polymer battery charging, and other features that - are often used in portable devices like cell phones and cameras. - - This driver can also be built as a module. If so, the module - will be called tps65010. + This is the core driver for the Janz CMOD-IO PCI MODULbus + carrier board. This device is a PCI to MODULbus bridge which may + host many different types of MODULbus daughterboards, including + CAN and GPIO controllers. -config TPS6507X - tristate "TPS6507x Power Management / Touch Screen chips" +config MFD_JZ4740_ADC + bool "Janz JZ4740 ADC core" select MFD_CORE - depends on I2C && GENERIC_HARDIRQS + select GENERIC_IRQ_CHIP + depends on MACH_JZ4740 help - If you say yes here you get support for the TPS6507x series of - Power Management / Touch Screen chips. These include voltage - regulators, lithium ion/polymer battery charging, touch screen - and other features that are often used in portable devices. - This driver can also be built as a module. If so, the module - will be called tps6507x. + Say yes here if you want support for the ADC unit in the JZ4740 SoC. + This driver is necessary for jz4740-battery and jz4740-hwmon driver. -config MFD_TPS65217 - tristate "TPS65217 Power Management / White LED chips" - depends on I2C && GENERIC_HARDIRQS - select MFD_CORE +config MFD_88PM800 + tristate "Marvell 88PM800" + depends on I2C=y && GENERIC_HARDIRQS select REGMAP_I2C + select REGMAP_IRQ + select MFD_CORE help - If you say yes here you get support for the TPS65217 series of - Power Management / White LED chips. - These include voltage regulators, lithium ion/polymer battery - charger, wled and other features that are often used in portable - devices. - - This driver can also be built as a module. If so, the module - will be called tps65217. + This supports for Marvell 88PM800 Power Management IC. + This includes the I2C driver and the core APIs _only_, you have to + select individual components like voltage regulators, RTC and + battery-charger under the corresponding menus. -config MFD_TPS6586X - bool "TPS6586x Power Management chips" +config MFD_88PM805 + tristate "Marvell 88PM805" depends on I2C=y && GENERIC_HARDIRQS - select MFD_CORE select REGMAP_I2C + select REGMAP_IRQ + select MFD_CORE help - If you say yes here you get support for the TPS6586X series of - Power Management chips. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the - functionality of the device. + This supports for Marvell 88PM805 Power Management IC. This includes + the I2C driver and the core APIs _only_, you have to select individual + components like codec device, headset/Mic device under the + corresponding menus. - This driver can also be built as a module. If so, the module - will be called tps6586x. +config MFD_88PM860X + bool "Marvell 88PM8606/88PM8607" + depends on I2C=y && GENERIC_HARDIRQS + select REGMAP_I2C + select MFD_CORE + help + This supports for Marvell 88PM8606/88PM8607 Power Management IC. + This includes the I2C driver and the core APIs _only_, you have to + select individual components like voltage regulators, RTC and + battery-charger under the corresponding menus. -config MFD_TPS65910 - bool "TPS65910 Power Management chip" - depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS +config MFD_MAX77686 + bool "Maxim Semiconductor MAX77686 PMIC Support" + depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE select REGMAP_I2C - select REGMAP_IRQ select IRQ_DOMAIN help - if you say yes here you get support for the TPS65910 series of - Power Management chips. - -config MFD_TPS65912 - bool - depends on GPIOLIB + Say yes here to support for Maxim Semiconductor MAX77686. + This is a Power Management IC with RTC on chip. + This driver provides common support for accessing the device; + additional drivers must be enabled in order to use the functionality + of the device. -config MFD_TPS65912_I2C - bool "TPS65912 Power Management chip with I2C" +config MFD_MAX77693 + bool "Maxim Semiconductor MAX77693 PMIC Support" + depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE - select MFD_TPS65912 - depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS + select REGMAP_I2C help - If you say yes here you get support for the TPS65912 series of - PM chips with I2C interface. + Say yes here to support for Maxim Semiconductor MAX77693. + This is a companion Power Management IC with Flash, Haptic, Charger, + and MUIC(Micro USB Interface Controller) controls on chip. + This driver provides common support for accessing the device; + additional drivers must be enabled in order to use the functionality + of the device. -config MFD_TPS65912_SPI - bool "TPS65912 Power Management chip with SPI" +config MFD_MAX8907 + tristate "Maxim Semiconductor MAX8907 PMIC Support" select MFD_CORE - select MFD_TPS65912 - depends on SPI_MASTER && GPIOLIB && GENERIC_HARDIRQS - help - If you say yes here you get support for the TPS65912 series of - PM chips with SPI interface. - -config MFD_TPS80031 - bool "TI TPS80031/TPS80032 Power Management chips" depends on I2C=y && GENERIC_HARDIRQS - select MFD_CORE select REGMAP_I2C select REGMAP_IRQ help - If you say yes here you get support for the Texas Instruments - TPS80031/ TPS80032 Fully Integrated Power Management with Power - Path and Battery Charger. The device provides five configurable - step-down converters, 11 general purpose LDOs, USB OTG Module, - ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with - Power Path from USB, 32K clock generator. + Say yes here to support for Maxim Semiconductor MAX8907. This is + a Power Management IC. This driver provides common support for + accessing the device; additional drivers must be enabled in order + to use the functionality of the device. -config MENELAUS - bool "Texas Instruments TWL92330/Menelaus PM chip" - depends on I2C=y && ARCH_OMAP2 +config MFD_MAX8925 + bool "Maxim Semiconductor MAX8925 PMIC Support" + depends on I2C=y && GENERIC_HARDIRQS + select MFD_CORE help - If you say yes here you get support for the Texas Instruments - TWL92330/Menelaus Power Management chip. This include voltage - regulators, Dual slot memory card transceivers, real-time clock - and other features that are often used in portable devices like - cell phones and PDAs. + Say yes here to support for Maxim Semiconductor MAX8925. This is + a Power Management IC. This driver provides common support for + accessing the device, additional drivers must be enabled in order + to use the functionality of the device. -config TWL4030_CORE - bool "Texas Instruments TWL4030/TWL5030/TWL6030/TPS659x0 Support" +config MFD_MAX8997 + bool "Maxim Semiconductor MAX8997/8966 PMIC Support" depends on I2C=y && GENERIC_HARDIRQS + select MFD_CORE select IRQ_DOMAIN - select REGMAP_I2C help - Say yes here if you have TWL4030 / TWL6030 family chip on your board. - This core driver provides register access and IRQ handling - facilities, and registers devices for the various functions - so that function-specific drivers can bind to them. - - These multi-function chips are found on many OMAP2 and OMAP3 - boards, providing power management, RTC, GPIO, keypad, a - high speed USB OTG transceiver, an audio codec (on most - versions) and many other features. + Say yes here to support for Maxim Semiconductor MAX8997/8966. + This is a Power Management IC with RTC, Flash, Fuel Gauge, Haptic, + MUIC controls on chip. + This driver provides common support for accessing the device; + additional drivers must be enabled in order to use the functionality + of the device. -config TWL4030_MADC - tristate "Texas Instruments TWL4030 MADC" - depends on TWL4030_CORE +config MFD_MAX8998 + bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support" + depends on I2C=y && GENERIC_HARDIRQS + select MFD_CORE help - This driver provides support for triton TWL4030-MADC. The - driver supports both RT and SW conversion methods. - - This driver can be built as a module. If so it will be - named twl4030-madc + Say yes here to support for Maxim Semiconductor MAX8998 and + National Semiconductor LP3974. This is a Power Management IC. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the functionality + of the device. -config TWL4030_POWER - bool "Support power resources on TWL4030 family chips" - depends on TWL4030_CORE && ARM +config EZX_PCAP + bool "Motorola EZXPCAP Support" + depends on GENERIC_HARDIRQS && SPI_MASTER help - Say yes here if you want to use the power resources on the - TWL4030 family chips. Most of these resources are regulators, - which have a separate driver; some are control signals, such - as clock request handshaking. - - This driver uses board-specific data to initialize the resources - and load scripts controlling which resources are switched off/on - or reset when a sleep, wakeup or warm reset event occurs. + This enables the PCAP ASIC present on EZX Phones. This is + needed for MMC, TouchScreen, Sound, USB, etc.. -config MFD_TWL4030_AUDIO - bool - depends on TWL4030_CORE && GENERIC_HARDIRQS +config MFD_VIPERBOARD + tristate "Nano River Technologies Viperboard" select MFD_CORE + depends on USB && GENERIC_HARDIRQS default n + help + Say yes here if you want support for Nano River Technologies + Viperboard. + There are mfd cell drivers available for i2c master, adc and + both gpios found on the board. The spi part does not yet + have a driver. + You need to select the mfd cell drivers separately. + The drivers do not support all features the board exposes. -config TWL6040_CORE - bool "Support for TWL6040 audio codec" - depends on I2C=y && GENERIC_HARDIRQS +config MFD_RETU + tristate "Nokia Retu multi-function device" select MFD_CORE - select REGMAP_I2C + depends on I2C && GENERIC_HARDIRQS select REGMAP_IRQ - default n help - Say yes here if you want support for Texas Instruments TWL6040 audio - codec. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the - functionality of the device (audio, vibra). + Retu is a multi-function device found on Nokia Internet Tablets + (770, N800 and N810). -config MFD_STMPE - bool "Support STMicroelectronics STMPE" - depends on (I2C=y || SPI_MASTER=y) && GENERIC_HARDIRQS - select MFD_CORE +config MFD_PCF50633 + tristate "NXP PCF50633" + depends on I2C + select REGMAP_I2C help - Support for the STMPE family of I/O Expanders from - STMicroelectronics. - - Currently supported devices are: - - STMPE811: GPIO, Touchscreen - STMPE1601: GPIO, Keypad - STMPE1801: GPIO, Keypad - STMPE2401: GPIO, Keypad - STMPE2403: GPIO, Keypad - - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the functionality - of the device. Currently available sub drivers are: - - GPIO: stmpe-gpio - Keypad: stmpe-keypad - Touchscreen: stmpe-ts - -menu "STMPE Interface Drivers" -depends on MFD_STMPE + Say yes here if you have NXP PCF50633 chip on your board. + This core driver provides register access and IRQ handling + facilities, and registers devices for the various functions + so that function-specific drivers can bind to them. -config STMPE_I2C - bool "STMPE I2C Inteface" - depends on I2C=y - default y +config PCF50633_ADC + tristate "NXP PCF50633 ADC" + depends on MFD_PCF50633 help - This is used to enable I2C interface of STMPE + Say yes here if you want to include support for ADC in the + NXP PCF50633 chip. -config STMPE_SPI - bool "STMPE SPI Inteface" - depends on SPI_MASTER +config PCF50633_GPIO + tristate "NXP PCF50633 GPIO" + depends on MFD_PCF50633 help - This is used to enable SPI interface of STMPE -endmenu + Say yes here if you want to include support GPIO for pins on + the PCF50633 chip. -config MFD_TC3589X - bool "Support Toshiba TC35892 and variants" - depends on I2C=y && GENERIC_HARDIRQS - select MFD_CORE +config UCB1400_CORE + tristate "Philips UCB1400 Core driver" + depends on AC97_BUS + depends on GPIOLIB help - Support for the Toshiba TC35892 and variants I/O Expander. + This enables support for the Philips UCB1400 core functions. + The UCB1400 is an AC97 audio codec. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the - functionality of the device. + To compile this driver as a module, choose M here: the + module will be called ucb1400_core. -config MFD_TMIO - bool - default n +config MFD_PM8XXX + tristate -config MFD_T7L66XB - bool "Support Toshiba T7L66XB" - depends on ARM && HAVE_CLK && GENERIC_HARDIRQS +config MFD_PM8921_CORE + tristate "Qualcomm PM8921 PMIC chip" + depends on MSM_SSBI select MFD_CORE - select MFD_TMIO + select MFD_PM8XXX help - Support for Toshiba Mobile IO Controller T7L66XB + If you say yes to this option, support will be included for the + built-in PM8921 PMIC chip. + + This is required if your board has a PM8921 and uses its features, + such as: MPPs, GPIOs, regulators, interrupts, and PWM. + + Say M here if you want to include support for PM8921 chip as a module. + This will build a module called "pm8921-core". + +config MFD_PM8XXX_IRQ + bool "Qualcomm PM8xxx IRQ features" + depends on MFD_PM8XXX + default y if MFD_PM8XXX + help + This is the IRQ driver for Qualcomm PM 8xxx PMIC chips. + + This is required to use certain other PM 8xxx features, such as GPIO + and MPP. + +config MFD_RDC321X + tristate "RDC R-321x southbridge" + select MFD_CORE + depends on PCI && GENERIC_HARDIRQS + help + Say yes here if you want to have support for the RDC R-321x SoC + southbridge which provides access to GPIOs and Watchdog using the + southbridge PCI device configuration space. + +config MFD_RTSX_PCI + tristate "Realtek PCI-E card reader" + depends on PCI && GENERIC_HARDIRQS + select MFD_CORE + help + This supports for Realtek PCI-Express card reader including rts5209, + rts5229, rtl8411, etc. Realtek card reader supports access to many + types of memory cards, such as Memory Stick, Memory Stick Pro, + Secure Digital and MultiMediaCard. + +config MFD_RC5T583 + bool "Ricoh RC5T583 Power Management system device" + depends on I2C=y && GENERIC_HARDIRQS + select MFD_CORE + select REGMAP_I2C + help + Select this option to get support for the RICOH583 Power + Management system device. + This driver provides common support for accessing the device + through i2c interface. The device supports multiple sub-devices + like GPIO, interrupts, RTC, LDO and DCDC regulators, onkey. + Additional drivers must be enabled in order to use the + different functionality of the device. + +config MFD_SEC_CORE + bool "SAMSUNG Electronics PMIC Series Support" + depends on I2C=y && GENERIC_HARDIRQS + select MFD_CORE + select REGMAP_I2C + select REGMAP_IRQ + help + Support for the Samsung Electronics MFD series. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the functionality + of the device + +config MFD_SM501 + tristate "Silicon Motion SM501" + ---help--- + This is the core driver for the Silicon Motion SM501 multimedia + companion chip. This device is a multifunction device which may + provide numerous interfaces including USB host controller, USB gadget, + asynchronous serial ports, audio functions, and a dual display video + interface. The device may be connected by PCI or local bus with + varying functions enabled. + +config MFD_SM501_GPIO + bool "Export GPIO via GPIO layer" + depends on MFD_SM501 && GPIOLIB + ---help--- + This option uses the gpio library layer to export the 64 GPIO + lines on the SM501. The platform data is used to supply the + base number for the first GPIO line to register. config MFD_SMSC - bool "Support for the SMSC ECE1099 series chips" + bool "SMSC ECE1099 series chips" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE select REGMAP_I2C @@ -457,433 +517,425 @@ config MFD_SMSC To compile this driver as a module, choose M here: the module will be called smsc. -config MFD_TC6387XB - bool "Support Toshiba TC6387XB" - depends on ARM && HAVE_CLK - select MFD_CORE - select MFD_TMIO +config ABX500_CORE + bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions" + default y if ARCH_U300 || ARCH_U8500 help - Support for Toshiba Mobile IO Controller TC6387XB + Say yes here if you have the ABX500 Mixed Signal IC family + chips. This core driver expose register access functions. + Functionality specific drivers using these functions can + remain unchanged when IC changes. Binding of the functions to + actual register access is done by the IC core driver. -config MFD_TC6393XB - bool "Support Toshiba TC6393XB" - depends on ARM && HAVE_CLK - select GPIOLIB +config AB3100_CORE + bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions" + depends on I2C=y && ABX500_CORE && GENERIC_HARDIRQS select MFD_CORE - select MFD_TMIO + default y if ARCH_U300 help - Support for Toshiba Mobile IO Controller TC6393XB + Select this to enable the AB3100 Mixed Signal IC core + functionality. This connects to a AB3100 on the I2C bus + and expose a number of symbols needed for dependent devices + to read and write registers and subscribe to events from + this multi-functional IC. This is needed to use other features + of the AB3100 such as battery-backed RTC, charging control, + LEDs, vibrator, system power and temperature, power management + and ALSA sound. -config PMIC_DA903X - bool "Dialog Semiconductor DA9030/DA9034 PMIC Support" - depends on I2C=y +config AB3100_OTP + tristate "ST-Ericsson AB3100 OTP functions" + depends on AB3100_CORE + default y if AB3100_CORE help - Say yes here to support for Dialog Semiconductor DA9030 (a.k.a - ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC - usually found on PXA processors-based platforms. This includes - the I2C driver and the core APIs _only_, you have to select - individual components like LCD backlight, voltage regulators, - LEDs and battery-charger under the corresponding menus. + Select this to enable the AB3100 Mixed Signal IC OTP (one-time + programmable memory) support. This exposes a sysfs file to read + out OTP values. -config PMIC_DA9052 - bool +config AB8500_CORE + bool "ST-Ericsson AB8500 Mixed Signal Power Management chip" + depends on GENERIC_HARDIRQS && ABX500_CORE && MFD_DB8500_PRCMU + select POWER_SUPPLY select MFD_CORE + select IRQ_DOMAIN + help + Select this option to enable access to AB8500 power management + chip. This connects to U8500 either on the SSP/SPI bus (deprecated + since hardware version v1.0) or the I2C bus via PRCMU. It also adds + the irq_chip parts for handling the Mixed Signal chip events. + This chip embeds various other multimedia funtionalities as well. -config MFD_DA9052_SPI - bool "Support Dialog Semiconductor DA9052/53 PMIC variants with SPI" - select REGMAP_SPI - select REGMAP_IRQ - select PMIC_DA9052 - depends on SPI_MASTER=y && GENERIC_HARDIRQS +config AB8500_DEBUG + bool "Enable debug info via debugfs" + depends on AB8500_CORE && DEBUG_FS + default y if DEBUG_FS + help + Select this option if you want debug information using the debug + filesystem, debugfs. + +config AB8500_GPADC + bool "ST-Ericsson AB8500 GPADC driver" + depends on AB8500_CORE && REGULATOR_AB8500 + default y help - Support for the Dialog Semiconductor DA9052 PMIC - when controlled using SPI. This driver provides common support - for accessing the device, additional drivers must be enabled in - order to use the functionality of the device. + AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage -config MFD_DA9052_I2C - bool "Support Dialog Semiconductor DA9052/53 PMIC variants with I2C" - select REGMAP_I2C - select REGMAP_IRQ - select PMIC_DA9052 - depends on I2C=y && GENERIC_HARDIRQS +config MFD_DB8500_PRCMU + bool "ST-Ericsson DB8500 Power Reset Control Management Unit" + depends on UX500_SOC_DB8500 + select MFD_CORE help - Support for the Dialog Semiconductor DA9052 PMIC - when controlled using I2C. This driver provides common support - for accessing the device, additional drivers must be enabled in - order to use the functionality of the device. + Select this option to enable support for the DB8500 Power Reset + and Control Management Unit. This is basically an autonomous + system controller running an XP70 microprocessor, which is accessed + through a register map. -config MFD_DA9055 - bool "Dialog Semiconductor DA9055 PMIC Support" - select REGMAP_I2C - select REGMAP_IRQ +config MFD_STMPE + bool "STMicroelectronics STMPE" + depends on (I2C=y || SPI_MASTER=y) && GENERIC_HARDIRQS select MFD_CORE - depends on I2C=y && GENERIC_HARDIRQS help - Say yes here for support of Dialog Semiconductor DA9055. This is - a Power Management IC. This driver provides common support for - accessing the device as well as the I2C interface to the chip itself. - Additional drivers must be enabled in order to use the functionality - of the device. + Support for the STMPE family of I/O Expanders from + STMicroelectronics. - This driver can be built as a module. If built as a module it will be - called "da9055" + Currently supported devices are: -config PMIC_ADP5520 - bool "Analog Devices ADP5520/01 MFD PMIC Core Support" + STMPE811: GPIO, Touchscreen + STMPE1601: GPIO, Keypad + STMPE1801: GPIO, Keypad + STMPE2401: GPIO, Keypad + STMPE2403: GPIO, Keypad + + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the functionality + of the device. Currently available sub drivers are: + + GPIO: stmpe-gpio + Keypad: stmpe-keypad + Touchscreen: stmpe-ts + +menu "STMicroelectronics STMPE Interface Drivers" +depends on MFD_STMPE + +config STMPE_I2C + bool "STMicroelectronics STMPE I2C Inteface" depends on I2C=y + default y help - Say yes here to add support for Analog Devices AD5520 and ADP5501, - Multifunction Power Management IC. This includes - the I2C driver and the core APIs _only_, you have to select - individual components like LCD backlight, LEDs, GPIOs and Kepad - under the corresponding menus. + This is used to enable I2C interface of STMPE -config MFD_LP8788 - bool "Texas Instruments LP8788 Power Management Unit Driver" - depends on I2C=y && GENERIC_HARDIRQS - select MFD_CORE - select REGMAP_I2C - select IRQ_DOMAIN +config STMPE_SPI + bool "STMicroelectronics STMPE SPI Inteface" + depends on SPI_MASTER help - TI LP8788 PMU supports regulators, battery charger, RTC, - ADC, backlight driver and current sinks. + This is used to enable SPI interface of STMPE +endmenu -config MFD_MAX77686 - bool "Maxim Semiconductor MAX77686 PMIC Support" - depends on I2C=y && GENERIC_HARDIRQS +config MFD_STA2X11 + bool "STMicroelectronics STA2X11" + depends on STA2X11 && GENERIC_HARDIRQS select MFD_CORE - select REGMAP_I2C - select IRQ_DOMAIN + select REGMAP_MMIO + +config MFD_SYSCON + bool "System Controller Register R/W Based on Regmap" + select REGMAP_MMIO help - Say yes here to support for Maxim Semiconductor MAX77686. - This is a Power Management IC with RTC on chip. - This driver provides common support for accessing the device; - additional drivers must be enabled in order to use the functionality - of the device. + Select this option to enable accessing system control registers + via regmap. -config MFD_MAX77693 - bool "Maxim Semiconductor MAX77693 PMIC Support" - depends on I2C=y && GENERIC_HARDIRQS +config MFD_DAVINCI_VOICECODEC + tristate select MFD_CORE - select REGMAP_I2C - help - Say yes here to support for Maxim Semiconductor MAX77693. - This is a companion Power Management IC with Flash, Haptic, Charger, - and MUIC(Micro USB Interface Controller) controls on chip. - This driver provides common support for accessing the device; - additional drivers must be enabled in order to use the functionality - of the device. -config MFD_MAX8907 - tristate "Maxim Semiconductor MAX8907 PMIC Support" +config MFD_TI_AM335X_TSCADC + tristate "TI ADC / Touch Screen chip support" select MFD_CORE - depends on I2C=y && GENERIC_HARDIRQS - select REGMAP_I2C - select REGMAP_IRQ + select REGMAP + select REGMAP_MMIO + depends on GENERIC_HARDIRQS help - Say yes here to support for Maxim Semiconductor MAX8907. This is - a Power Management IC. This driver provides common support for - accessing the device; additional drivers must be enabled in order - to use the functionality of the device. + If you say yes here you get support for Texas Instruments series + of Touch Screen /ADC chips. + To compile this driver as a module, choose M here: the + module will be called ti_am335x_tscadc. -config MFD_MAX8925 - bool "Maxim Semiconductor MAX8925 PMIC Support" - depends on I2C=y && GENERIC_HARDIRQS - select MFD_CORE +config MFD_DM355EVM_MSP + bool "TI DaVinci DM355 EVM microcontroller" + depends on I2C=y && MACH_DAVINCI_DM355_EVM help - Say yes here to support for Maxim Semiconductor MAX8925. This is - a Power Management IC. This driver provides common support for - accessing the device, additional drivers must be enabled in order - to use the functionality of the device. + This driver supports the MSP430 microcontroller used on these + boards. MSP430 firmware manages resets and power sequencing, + inputs from buttons and the IR remote, LEDs, an RTC, and more. -config MFD_MAX8997 - bool "Maxim Semiconductor MAX8997/8966 PMIC Support" +config MFD_LP8788 + bool "TI LP8788 Power Management Unit Driver" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE + select REGMAP_I2C select IRQ_DOMAIN help - Say yes here to support for Maxim Semiconductor MAX8997/8966. - This is a Power Management IC with RTC, Flash, Fuel Gauge, Haptic, - MUIC controls on chip. - This driver provides common support for accessing the device; - additional drivers must be enabled in order to use the functionality - of the device. + TI LP8788 PMU supports regulators, battery charger, RTC, + ADC, backlight driver and current sinks. -config MFD_MAX8998 - bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support" - depends on I2C=y && GENERIC_HARDIRQS - select MFD_CORE +config MFD_OMAP_USB_HOST + bool "TI OMAP USBHS core and TLL driver" + depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3 + default y help - Say yes here to support for Maxim Semiconductor MAX8998 and - National Semiconductor LP3974. This is a Power Management IC. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the functionality - of the device. + This is the core driver for the OAMP EHCI and OHCI drivers. + This MFD driver does the required setup functionalities for + OMAP USB Host drivers. -config MFD_SEC_CORE - bool "SAMSUNG Electronics PMIC Series Support" - depends on I2C=y && GENERIC_HARDIRQS +config MFD_PALMAS + bool "TI Palmas series chips" select MFD_CORE select REGMAP_I2C select REGMAP_IRQ + depends on I2C=y && GENERIC_HARDIRQS help - Support for the Samsung Electronics MFD series. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the functionality - of the device + If you say yes here you get support for the Palmas + series of PMIC chips from Texas Instruments. -config MFD_ARIZONA - select REGMAP - select REGMAP_IRQ +config MFD_TI_SSP + tristate "TI Sequencer Serial Port support" + depends on ARCH_DAVINCI_TNETV107X && GENERIC_HARDIRQS select MFD_CORE - bool + ---help--- + Say Y here if you want support for the Sequencer Serial Port + in a Texas Instruments TNETV107X SoC. -config MFD_ARIZONA_I2C - tristate "Support Wolfson Microelectronics Arizona platform with I2C" - select MFD_ARIZONA + To compile this driver as a module, choose M here: the + module will be called ti-ssp. + +config TPS6105X + tristate "TI TPS61050/61052 Boost Converters" + depends on I2C + select REGULATOR + select MFD_CORE + select REGULATOR_FIXED_VOLTAGE + depends on GENERIC_HARDIRQS + help + This option enables a driver for the TP61050/TPS61052 + high-power "white LED driver". This boost converter is + sometimes used for other things than white LEDs, and + also contains a GPIO pin. + +config TPS65010 + tristate "TI TPS6501x Power Management chips" + depends on I2C && GPIOLIB + default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK + help + If you say yes here you get support for the TPS6501x series of + Power Management chips. These include voltage regulators, + lithium ion/polymer battery charging, and other features that + are often used in portable devices like cell phones and cameras. + + This driver can also be built as a module. If so, the module + will be called tps65010. + +config TPS6507X + tristate "TI TPS6507x Power Management / Touch Screen chips" select MFD_CORE - select REGMAP_I2C depends on I2C && GENERIC_HARDIRQS help - Support for the Wolfson Microelectronics Arizona platform audio SoC - core functionality controlled via I2C. + If you say yes here you get support for the TPS6507x series of + Power Management / Touch Screen chips. These include voltage + regulators, lithium ion/polymer battery charging, touch screen + and other features that are often used in portable devices. + This driver can also be built as a module. If so, the module + will be called tps6507x. -config MFD_ARIZONA_SPI - tristate "Support Wolfson Microelectronics Arizona platform with SPI" - select MFD_ARIZONA +config TPS65911_COMPARATOR + tristate + +config MFD_TPS65090 + bool "TI TPS65090 Power Management chips" + depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE - select REGMAP_SPI - depends on SPI_MASTER && GENERIC_HARDIRQS + select REGMAP_I2C + select REGMAP_IRQ help - Support for the Wolfson Microelectronics Arizona platform audio SoC - core functionality controlled via I2C. + If you say yes here you get support for the TPS65090 series of + Power Management chips. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the + functionality of the device. -config MFD_WM5102 - bool "Support Wolfson Microelectronics WM5102" - depends on MFD_ARIZONA +config MFD_TPS65217 + tristate "TI TPS65217 Power Management / White LED chips" + depends on I2C && GENERIC_HARDIRQS + select MFD_CORE + select REGMAP_I2C help - Support for Wolfson Microelectronics WM5102 low power audio SoC + If you say yes here you get support for the TPS65217 series of + Power Management / White LED chips. + These include voltage regulators, lithium ion/polymer battery + charger, wled and other features that are often used in portable + devices. -config MFD_WM5110 - bool "Support Wolfson Microelectronics WM5110" - depends on MFD_ARIZONA - help - Support for Wolfson Microelectronics WM5110 low power audio SoC + This driver can also be built as a module. If so, the module + will be called tps65217. -config MFD_WM8400 - bool "Support Wolfson Microelectronics WM8400" - select MFD_CORE +config MFD_TPS6586X + bool "TI TPS6586x Power Management chips" depends on I2C=y && GENERIC_HARDIRQS + select MFD_CORE select REGMAP_I2C help - Support for the Wolfson Microelecronics WM8400 PMIC and audio - CODEC. This driver provides common support for accessing - the device, additional drivers must be enabled in order to use - the functionality of the device. + If you say yes here you get support for the TPS6586X series of + Power Management chips. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the + functionality of the device. -config MFD_WM831X - bool - depends on GENERIC_HARDIRQS + This driver can also be built as a module. If so, the module + will be called tps6586x. -config MFD_WM831X_I2C - bool "Support Wolfson Microelectronics WM831x/2x PMICs with I2C" +config MFD_TPS65910 + bool "TI TPS65910 Power Management chip" + depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS select MFD_CORE - select MFD_WM831X select REGMAP_I2C + select REGMAP_IRQ select IRQ_DOMAIN - depends on I2C=y && GENERIC_HARDIRQS help - Support for the Wolfson Microelecronics WM831x and WM832x PMICs - when controlled using I2C. This driver provides common support - for accessing the device, additional drivers must be enabled in - order to use the functionality of the device. + if you say yes here you get support for the TPS65910 series of + Power Management chips. -config MFD_WM831X_SPI - bool "Support Wolfson Microelectronics WM831x/2x PMICs with SPI" - select MFD_CORE - select MFD_WM831X - select REGMAP_SPI - select IRQ_DOMAIN - depends on SPI_MASTER && GENERIC_HARDIRQS +config MFD_TPS65912 + bool "TI TPS65912 Power Management chip" + depends on GPIOLIB help - Support for the Wolfson Microelecronics WM831x and WM832x PMICs - when controlled using SPI. This driver provides common support - for accessing the device, additional drivers must be enabled in - order to use the functionality of the device. + If you say yes here you get support for the TPS65912 series of + PM chips. -config MFD_WM8350 - bool - depends on GENERIC_HARDIRQS +config MFD_TPS65912_I2C + bool "TI TPS65912 Power Management chip with I2C" + select MFD_CORE + select MFD_TPS65912 + depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS + help + If you say yes here you get support for the TPS65912 series of + PM chips with I2C interface. -config MFD_WM8350_I2C - bool "Support Wolfson Microelectronics WM8350 with I2C" - select MFD_WM8350 - depends on I2C=y && GENERIC_HARDIRQS +config MFD_TPS65912_SPI + bool "TI TPS65912 Power Management chip with SPI" + select MFD_CORE + select MFD_TPS65912 + depends on SPI_MASTER && GPIOLIB && GENERIC_HARDIRQS help - The WM8350 is an integrated audio and power management - subsystem with watchdog and RTC functionality for embedded - systems. This option enables core support for the WM8350 with - I2C as the control interface. Additional options must be - selected to enable support for the functionality of the chip. + If you say yes here you get support for the TPS65912 series of + PM chips with SPI interface. -config MFD_WM8994 - bool "Support Wolfson Microelectronics WM8994" +config MFD_TPS80031 + bool "TI TPS80031/TPS80032 Power Management chips" + depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE select REGMAP_I2C select REGMAP_IRQ - depends on I2C=y && GENERIC_HARDIRQS help - The WM8994 is a highly integrated hi-fi CODEC designed for - smartphone applicatiosn. As well as audio functionality it - has on board GPIO and regulator functionality which is - supported via the relevant subsystems. This driver provides - core support for the WM8994, in order to use the actual - functionaltiy of the device other drivers must be enabled. + If you say yes here you get support for the Texas Instruments + TPS80031/ TPS80032 Fully Integrated Power Management with Power + Path and Battery Charger. The device provides five configurable + step-down converters, 11 general purpose LDOs, USB OTG Module, + ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with + Power Path from USB, 32K clock generator. -config MFD_PCF50633 - tristate "Support for NXP PCF50633" - depends on I2C +config TWL4030_CORE + bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 Support" + depends on I2C=y && GENERIC_HARDIRQS + select IRQ_DOMAIN select REGMAP_I2C help - Say yes here if you have NXP PCF50633 chip on your board. + Say yes here if you have TWL4030 / TWL6030 family chip on your board. This core driver provides register access and IRQ handling facilities, and registers devices for the various functions so that function-specific drivers can bind to them. -config PCF50633_ADC - tristate "Support for NXP PCF50633 ADC" - depends on MFD_PCF50633 - help - Say yes here if you want to include support for ADC in the - NXP PCF50633 chip. - -config PCF50633_GPIO - tristate "Support for NXP PCF50633 GPIO" - depends on MFD_PCF50633 - help - Say yes here if you want to include support GPIO for pins on - the PCF50633 chip. - -config MFD_MC13783 - tristate + These multi-function chips are found on many OMAP2 and OMAP3 + boards, providing power management, RTC, GPIO, keypad, a + high speed USB OTG transceiver, an audio codec (on most + versions) and many other features. -config MFD_MC13XXX - tristate - depends on (SPI_MASTER || I2C) && GENERIC_HARDIRQS - select MFD_CORE - select MFD_MC13783 +config TWL4030_MADC + tristate "TI TWL4030 MADC" + depends on TWL4030_CORE help - Enable support for the Freescale MC13783 and MC13892 PMICs. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the - functionality of the device. + This driver provides support for triton TWL4030-MADC. The + driver supports both RT and SW conversion methods. -config MFD_MC13XXX_SPI - tristate "Freescale MC13783 and MC13892 SPI interface" - depends on SPI_MASTER && GENERIC_HARDIRQS - select REGMAP_SPI - select MFD_MC13XXX - help - Select this if your MC13xxx is connected via an SPI bus. + This driver can be built as a module. If so it will be + named twl4030-madc -config MFD_MC13XXX_I2C - tristate "Freescale MC13892 I2C interface" - depends on I2C && GENERIC_HARDIRQS - select REGMAP_I2C - select MFD_MC13XXX +config TWL4030_POWER + bool "TI TWL4030 power resources" + depends on TWL4030_CORE && ARM help - Select this if your MC13xxx is connected via an I2C bus. + Say yes here if you want to use the power resources on the + TWL4030 family chips. Most of these resources are regulators, + which have a separate driver; some are control signals, such + as clock request handshaking. -config ABX500_CORE - bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions" - default y if ARCH_U300 || ARCH_U8500 - help - Say yes here if you have the ABX500 Mixed Signal IC family - chips. This core driver expose register access functions. - Functionality specific drivers using these functions can - remain unchanged when IC changes. Binding of the functions to - actual register access is done by the IC core driver. + This driver uses board-specific data to initialize the resources + and load scripts controlling which resources are switched off/on + or reset when a sleep, wakeup or warm reset event occurs. -config AB3100_CORE - bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions" - depends on I2C=y && ABX500_CORE && GENERIC_HARDIRQS +config MFD_TWL4030_AUDIO + bool "TI TWL4030 Audio" + depends on TWL4030_CORE && GENERIC_HARDIRQS select MFD_CORE - default y if ARCH_U300 - help - Select this to enable the AB3100 Mixed Signal IC core - functionality. This connects to a AB3100 on the I2C bus - and expose a number of symbols needed for dependent devices - to read and write registers and subscribe to events from - this multi-functional IC. This is needed to use other features - of the AB3100 such as battery-backed RTC, charging control, - LEDs, vibrator, system power and temperature, power management - and ALSA sound. - -config AB3100_OTP - tristate "ST-Ericsson AB3100 OTP functions" - depends on AB3100_CORE - default y if AB3100_CORE - help - Select this to enable the AB3100 Mixed Signal IC OTP (one-time - programmable memory) support. This exposes a sysfs file to read - out OTP values. + default n -config AB8500_CORE - bool "ST-Ericsson AB8500 Mixed Signal Power Management chip" - depends on GENERIC_HARDIRQS && ABX500_CORE && MFD_DB8500_PRCMU - select POWER_SUPPLY +config TWL6040_CORE + bool "TI TWL6040 audio codec" + depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE - select IRQ_DOMAIN - help - Select this option to enable access to AB8500 power management - chip. This connects to U8500 either on the SSP/SPI bus (deprecated - since hardware version v1.0) or the I2C bus via PRCMU. It also adds - the irq_chip parts for handling the Mixed Signal chip events. - This chip embeds various other multimedia funtionalities as well. - -config AB8500_DEBUG - bool "Enable debug info via debugfs" - depends on AB8500_CORE && DEBUG_FS - default y if DEBUG_FS - help - Select this option if you want debug information using the debug - filesystem, debugfs. - -config AB8500_GPADC - bool "AB8500 GPADC driver" - depends on AB8500_CORE && REGULATOR_AB8500 - default y + select REGMAP_I2C + select REGMAP_IRQ + default n help - AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage + Say yes here if you want support for Texas Instruments TWL6040 audio + codec. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the + functionality of the device (audio, vibra). -config EZX_PCAP - bool "PCAP Support" - depends on GENERIC_HARDIRQS && SPI_MASTER +config MENELAUS + bool "TI TWL92330/Menelaus PM chip" + depends on I2C=y && ARCH_OMAP2 help - This enables the PCAP ASIC present on EZX Phones. This is - needed for MMC, TouchScreen, Sound, USB, etc.. + If you say yes here you get support for the Texas Instruments + TWL92330/Menelaus Power Management chip. This include voltage + regulators, Dual slot memory card transceivers, real-time clock + and other features that are often used in portable devices like + cell phones and PDAs. -config MFD_DB8500_PRCMU - bool "ST-Ericsson DB8500 Power Reset Control Management Unit" - depends on UX500_SOC_DB8500 +config MFD_WL1273_CORE + tristate "TI WL1273 FM radio" + depends on I2C && GENERIC_HARDIRQS select MFD_CORE + default n help - Select this option to enable support for the DB8500 Power Reset - and Control Management Unit. This is basically an autonomous - system controller running an XP70 microprocessor, which is accessed - through a register map. + This is the core driver for the TI WL1273 FM radio. This MFD + driver connects the radio-wl1273 V4L2 module and the wl1273 + audio codec. -config MFD_CS5535 - tristate "Support for CS5535 and CS5536 southbridge core functions" +config MFD_LM3533 + tristate "TI/National Semiconductor LM3533 Lighting Power chip" + depends on I2C select MFD_CORE - depends on PCI && X86 - ---help--- - This is the core driver for CS5535/CS5536 MFD functions. This is - necessary for using the board's GPIO and MFGPT functionality. + select REGMAP_I2C + depends on GENERIC_HARDIRQS + help + Say yes here to enable support for National Semiconductor / TI + LM3533 Lighting Power chips. + + This driver provides common support for accessing the device; + additional drivers must be enabled in order to use the LED, + backlight or ambient-light-sensor functionality of the device. config MFD_TIMBERDALE - tristate "Support for the Timberdale FPGA" + tristate "Timberdale FPGA" select MFD_CORE depends on PCI && GPIOLIB ---help--- @@ -893,54 +945,48 @@ config MFD_TIMBERDALE The timberdale FPGA can be found on the Intel Atom development board for in-vehicle infontainment, called Russellville. -config LPC_SCH - tristate "Intel SCH LPC" - depends on PCI && GENERIC_HARDIRQS +config MFD_TC3589X + bool "Toshiba TC35892 and variants" + depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE help - LPC bridge function of the Intel SCH provides support for - System Management Bus and General Purpose I/O. + Support for the Toshiba TC35892 and variants I/O Expander. -config LPC_ICH - tristate "Intel ICH LPC" - depends on PCI && GENERIC_HARDIRQS - select MFD_CORE - help - The LPC bridge function of the Intel ICH provides support for - many functional units. This driver provides needed support for - other drivers to control these functions, currently GPIO and - watchdog. + This driver provides common support for accessing the device, + additional drivers must be enabled in order to use the + functionality of the device. -config MFD_RDC321X - tristate "Support for RDC-R321x southbridge" +config MFD_TMIO + bool + default n + +config MFD_T7L66XB + bool "Toshiba T7L66XB" + depends on ARM && HAVE_CLK && GENERIC_HARDIRQS select MFD_CORE - depends on PCI && GENERIC_HARDIRQS + select MFD_TMIO help - Say yes here if you want to have support for the RDC R-321x SoC - southbridge which provides access to GPIOs and Watchdog using the - southbridge PCI device configuration space. + Support for Toshiba Mobile IO Controller T7L66XB -config MFD_JANZ_CMODIO - tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board" +config MFD_TC6387XB + bool "Toshiba TC6387XB" + depends on ARM && HAVE_CLK select MFD_CORE - depends on PCI && GENERIC_HARDIRQS + select MFD_TMIO help - This is the core driver for the Janz CMOD-IO PCI MODULbus - carrier board. This device is a PCI to MODULbus bridge which may - host many different types of MODULbus daughterboards, including - CAN and GPIO controllers. + Support for Toshiba Mobile IO Controller TC6387XB -config MFD_JZ4740_ADC - bool "Support for the JZ4740 SoC ADC core" +config MFD_TC6393XB + bool "Toshiba TC6393XB" + depends on ARM && HAVE_CLK + select GPIOLIB select MFD_CORE - select GENERIC_IRQ_CHIP - depends on MACH_JZ4740 + select MFD_TMIO help - Say yes here if you want support for the ADC unit in the JZ4740 SoC. - This driver is necessary for jz4740-battery and jz4740-hwmon driver. + Support for Toshiba Mobile IO Controller TC6393XB config MFD_VX855 - tristate "Support for VIA VX855/VX875 integrated south bridge" + tristate "VIA VX855/VX875 integrated south bridge" depends on PCI && GENERIC_HARDIRQS select MFD_CORE help @@ -948,156 +994,113 @@ config MFD_VX855 VIA VX855/VX875 south bridge. You will need to enable the vx855_spi and/or vx855_gpio drivers for this to do anything useful. -config MFD_WL1273_CORE - tristate "Support for TI WL1273 FM radio." - depends on I2C && GENERIC_HARDIRQS +config MFD_ARIZONA + select REGMAP + select REGMAP_IRQ select MFD_CORE - default n - help - This is the core driver for the TI WL1273 FM radio. This MFD - driver connects the radio-wl1273 V4L2 module and the wl1273 - audio codec. - -config MFD_OMAP_USB_HOST - bool "Support OMAP USBHS core and TLL driver" - depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3 - default y - help - This is the core driver for the OAMP EHCI and OHCI drivers. - This MFD driver does the required setup functionalities for - OMAP USB Host drivers. - -config MFD_PM8XXX - tristate + bool -config MFD_PM8921_CORE - tristate "Qualcomm PM8921 PMIC chip" - depends on MSM_SSBI +config MFD_ARIZONA_I2C + tristate "Wolfson Microelectronics Arizona platform with I2C" + select MFD_ARIZONA select MFD_CORE - select MFD_PM8XXX - help - If you say yes to this option, support will be included for the - built-in PM8921 PMIC chip. - - This is required if your board has a PM8921 and uses its features, - such as: MPPs, GPIOs, regulators, interrupts, and PWM. - - Say M here if you want to include support for PM8921 chip as a module. - This will build a module called "pm8921-core". - -config MFD_PM8XXX_IRQ - bool "Support for Qualcomm PM8xxx IRQ features" - depends on MFD_PM8XXX - default y if MFD_PM8XXX + select REGMAP_I2C + depends on I2C && GENERIC_HARDIRQS help - This is the IRQ driver for Qualcomm PM 8xxx PMIC chips. - - This is required to use certain other PM 8xxx features, such as GPIO - and MPP. - -config TPS65911_COMPARATOR - tristate + Support for the Wolfson Microelectronics Arizona platform audio SoC + core functionality controlled via I2C. -config MFD_TPS65090 - bool "TPS65090 Power Management chips" - depends on I2C=y && GENERIC_HARDIRQS +config MFD_ARIZONA_SPI + tristate "Wolfson Microelectronics Arizona platform with SPI" + select MFD_ARIZONA select MFD_CORE - select REGMAP_I2C - select REGMAP_IRQ + select REGMAP_SPI + depends on SPI_MASTER && GENERIC_HARDIRQS help - If you say yes here you get support for the TPS65090 series of - Power Management chips. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the - functionality of the device. + Support for the Wolfson Microelectronics Arizona platform audio SoC + core functionality controlled via I2C. -config MFD_AAT2870_CORE - bool "Support for the AnalogicTech AAT2870" - select MFD_CORE - depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS +config MFD_WM5102 + bool "Wolfson Microelectronics WM5102" + depends on MFD_ARIZONA help - If you say yes here you get support for the AAT2870. - This driver provides common support for accessing the device, - additional drivers must be enabled in order to use the - functionality of the device. + Support for Wolfson Microelectronics WM5102 low power audio SoC -config MFD_INTEL_MSIC - bool "Support for Intel MSIC" - depends on INTEL_SCU_IPC - select MFD_CORE +config MFD_WM5110 + bool "Wolfson Microelectronics WM5110" + depends on MFD_ARIZONA help - Select this option to enable access to Intel MSIC (Avatele - Passage) chip. This chip embeds audio, battery, GPIO, etc. - devices used in Intel Medfield platforms. + Support for Wolfson Microelectronics WM5110 low power audio SoC -config MFD_RC5T583 - bool "Ricoh RC5T583 Power Management system device" - depends on I2C=y && GENERIC_HARDIRQS +config MFD_WM8400 + bool "Wolfson Microelectronics WM8400" select MFD_CORE + depends on I2C=y && GENERIC_HARDIRQS select REGMAP_I2C help - Select this option to get support for the RICOH583 Power - Management system device. - This driver provides common support for accessing the device - through i2c interface. The device supports multiple sub-devices - like GPIO, interrupts, RTC, LDO and DCDC regulators, onkey. - Additional drivers must be enabled in order to use the - different functionality of the device. - -config MFD_STA2X11 - bool "STA2X11 multi function device support" - depends on STA2X11 && GENERIC_HARDIRQS - select MFD_CORE - select REGMAP_MMIO + Support for the Wolfson Microelecronics WM8400 PMIC and audio + CODEC. This driver provides common support for accessing + the device, additional drivers must be enabled in order to use + the functionality of the device. -config MFD_SYSCON - bool "System Controller Register R/W Based on Regmap" - select REGMAP_MMIO - help - Select this option to enable accessing system control registers - via regmap. +config MFD_WM831X + bool + depends on GENERIC_HARDIRQS -config MFD_PALMAS - bool "Support for the TI Palmas series chips" +config MFD_WM831X_I2C + bool "Wolfson Microelectronics WM831x/2x PMICs with I2C" select MFD_CORE + select MFD_WM831X select REGMAP_I2C - select REGMAP_IRQ + select IRQ_DOMAIN depends on I2C=y && GENERIC_HARDIRQS help - If you say yes here you get support for the Palmas - series of PMIC chips from Texas Instruments. + Support for the Wolfson Microelecronics WM831x and WM832x PMICs + when controlled using I2C. This driver provides common support + for accessing the device, additional drivers must be enabled in + order to use the functionality of the device. -config MFD_VIPERBOARD - tristate "Support for Nano River Technologies Viperboard" +config MFD_WM831X_SPI + bool "Wolfson Microelectronics WM831x/2x PMICs with SPI" select MFD_CORE - depends on USB && GENERIC_HARDIRQS - default n + select MFD_WM831X + select REGMAP_SPI + select IRQ_DOMAIN + depends on SPI_MASTER && GENERIC_HARDIRQS help - Say yes here if you want support for Nano River Technologies - Viperboard. - There are mfd cell drivers available for i2c master, adc and - both gpios found on the board. The spi part does not yet - have a driver. - You need to select the mfd cell drivers separately. - The drivers do not support all features the board exposes. + Support for the Wolfson Microelecronics WM831x and WM832x PMICs + when controlled using SPI. This driver provides common support + for accessing the device, additional drivers must be enabled in + order to use the functionality of the device. -config MFD_RETU - tristate "Support for Retu multi-function device" - select MFD_CORE - depends on I2C && GENERIC_HARDIRQS - select REGMAP_IRQ +config MFD_WM8350 + bool + depends on GENERIC_HARDIRQS + +config MFD_WM8350_I2C + bool "Wolfson Microelectronics WM8350 with I2C" + select MFD_WM8350 + depends on I2C=y && GENERIC_HARDIRQS help - Retu is a multi-function device found on Nokia Internet Tablets - (770, N800 and N810). + The WM8350 is an integrated audio and power management + subsystem with watchdog and RTC functionality for embedded + systems. This option enables core support for the WM8350 with + I2C as the control interface. Additional options must be + selected to enable support for the functionality of the chip. -config MFD_AS3711 - bool "Support for AS3711" +config MFD_WM8994 + bool "Wolfson Microelectronics WM8994" select MFD_CORE select REGMAP_I2C select REGMAP_IRQ depends on I2C=y && GENERIC_HARDIRQS help - Support for the AS3711 PMIC from AMS + The WM8994 is a highly integrated hi-fi CODEC designed for + smartphone applicatiosn. As well as audio functionality it + has on board GPIO and regulator functionality which is + supported via the relevant subsystems. This driver provides + core support for the WM8994, in order to use the actual + functionaltiy of the device other drivers must be enabled. endmenu endif -- cgit v0.10.2