From 86e09287e4f8c81831b4d4118a48597565f0d21b Mon Sep 17 00:00:00 2001 From: Alexander Holler Date: Mon, 22 Nov 2010 21:09:01 +0100 Subject: Bluetooth: ath3k: reduce memory usage There is no need to hold the firmware in memory. Signed-off-by: Alexander Holler Signed-off-by: Gustavo F. Padovan diff --git a/drivers/bluetooth/ath3k.c b/drivers/bluetooth/ath3k.c index 949ed09..a126e61 100644 --- a/drivers/bluetooth/ath3k.c +++ b/drivers/bluetooth/ath3k.c @@ -47,46 +47,40 @@ MODULE_DEVICE_TABLE(usb, ath3k_table); #define USB_REQ_DFU_DNLOAD 1 #define BULK_SIZE 4096 -struct ath3k_data { - struct usb_device *udev; - u8 *fw_data; - u32 fw_size; - u32 fw_sent; -}; - -static int ath3k_load_firmware(struct ath3k_data *data, - unsigned char *firmware, - int count) +static int ath3k_load_firmware(struct usb_device *udev, + const struct firmware *firmware) { u8 *send_buf; int err, pipe, len, size, sent = 0; + int count = firmware->size; - BT_DBG("ath3k %p udev %p", data, data->udev); + BT_DBG("udev %p", udev); - pipe = usb_sndctrlpipe(data->udev, 0); + pipe = usb_sndctrlpipe(udev, 0); - if ((usb_control_msg(data->udev, pipe, + send_buf = kmalloc(BULK_SIZE, GFP_ATOMIC); + if (!send_buf) { + BT_ERR("Can't allocate memory chunk for firmware"); + return -ENOMEM; + } + + memcpy(send_buf, firmware->data, 20); + if ((err = usb_control_msg(udev, pipe, USB_REQ_DFU_DNLOAD, USB_TYPE_VENDOR, 0, 0, - firmware, 20, USB_CTRL_SET_TIMEOUT)) < 0) { + send_buf, 20, USB_CTRL_SET_TIMEOUT)) < 0) { BT_ERR("Can't change to loading configuration err"); - return -EBUSY; + goto error; } sent += 20; count -= 20; - send_buf = kmalloc(BULK_SIZE, GFP_ATOMIC); - if (!send_buf) { - BT_ERR("Can't allocate memory chunk for firmware"); - return -ENOMEM; - } - while (count) { size = min_t(uint, count, BULK_SIZE); - pipe = usb_sndbulkpipe(data->udev, 0x02); - memcpy(send_buf, firmware + sent, size); + pipe = usb_sndbulkpipe(udev, 0x02); + memcpy(send_buf, firmware->data + sent, size); - err = usb_bulk_msg(data->udev, pipe, send_buf, size, + err = usb_bulk_msg(udev, pipe, send_buf, size, &len, 3000); if (err || (len != size)) { @@ -112,57 +106,28 @@ static int ath3k_probe(struct usb_interface *intf, { const struct firmware *firmware; struct usb_device *udev = interface_to_usbdev(intf); - struct ath3k_data *data; - int size; BT_DBG("intf %p id %p", intf, id); if (intf->cur_altsetting->desc.bInterfaceNumber != 0) return -ENODEV; - data = kzalloc(sizeof(*data), GFP_KERNEL); - if (!data) - return -ENOMEM; - - data->udev = udev; - if (request_firmware(&firmware, "ath3k-1.fw", &udev->dev) < 0) { - kfree(data); return -EIO; } - size = max_t(uint, firmware->size, 4096); - data->fw_data = kmalloc(size, GFP_KERNEL); - if (!data->fw_data) { + if (ath3k_load_firmware(udev, firmware)) { release_firmware(firmware); - kfree(data); - return -ENOMEM; - } - - memcpy(data->fw_data, firmware->data, firmware->size); - data->fw_size = firmware->size; - data->fw_sent = 0; - release_firmware(firmware); - - usb_set_intfdata(intf, data); - if (ath3k_load_firmware(data, data->fw_data, data->fw_size)) { - usb_set_intfdata(intf, NULL); - kfree(data->fw_data); - kfree(data); return -EIO; } + release_firmware(firmware); return 0; } static void ath3k_disconnect(struct usb_interface *intf) { - struct ath3k_data *data = usb_get_intfdata(intf); - BT_DBG("ath3k_disconnect intf %p", intf); - - kfree(data->fw_data); - kfree(data); } static struct usb_driver ath3k_driver = { -- cgit v0.10.2 From 4571928fc73589e9c5217cd069d2c0b4ff1818a8 Mon Sep 17 00:00:00 2001 From: David Sterba Date: Fri, 14 Jan 2011 14:59:44 +0100 Subject: Bluetooth: l2cap: fix misuse of logical operation in place of bitop MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit CC: Marcel Holtmann CC: "Gustavo F. Padovan" CC: João Paulo Rechi Vita Signed-off-by: David Sterba Signed-off-by: Gustavo F. Padovan diff --git a/net/bluetooth/l2cap.c b/net/bluetooth/l2cap.c index c791fcd..4fd88eb 100644 --- a/net/bluetooth/l2cap.c +++ b/net/bluetooth/l2cap.c @@ -1893,8 +1893,8 @@ static int l2cap_sock_sendmsg(struct kiocb *iocb, struct socket *sock, struct ms if (pi->mode == L2CAP_MODE_STREAMING) { l2cap_streaming_send(sk); } else { - if (pi->conn_state & L2CAP_CONN_REMOTE_BUSY && - pi->conn_state && L2CAP_CONN_WAIT_F) { + if ((pi->conn_state & L2CAP_CONN_REMOTE_BUSY) && + (pi->conn_state & L2CAP_CONN_WAIT_F)) { err = len; break; } -- cgit v0.10.2 From e2e0cacbd4b0c7c69c7591d37c243f2363aeaa71 Mon Sep 17 00:00:00 2001 From: Johan Hedberg Date: Tue, 4 Jan 2011 12:08:50 +0200 Subject: Bluetooth: Fix leaking blacklist when unregistering a hci device The blacklist should be freed before the hci device gets unregistered. Signed-off-by: Johan Hedberg Signed-off-by: Gustavo F. Padovan diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c index 8b602d8..9c4541b 100644 --- a/net/bluetooth/hci_core.c +++ b/net/bluetooth/hci_core.c @@ -1011,6 +1011,10 @@ int hci_unregister_dev(struct hci_dev *hdev) destroy_workqueue(hdev->workqueue); + hci_dev_lock_bh(hdev); + hci_blacklist_clear(hdev); + hci_dev_unlock_bh(hdev); + __hci_dev_put(hdev); return 0; -- cgit v0.10.2 From 683d949a7fbf33c244670e34d35c460e0d6558cb Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Luk=C3=A1=C5=A1=20Turek?= <8an@praha12.net> Date: Wed, 5 Jan 2011 02:43:59 +0100 Subject: Bluetooth: Never deallocate a session when some DLC points to it Fix a bug introduced in commit 9cf5b0ea3a7f1432c61029f7aaf4b8b338628884: function rfcomm_recv_ua calls rfcomm_session_put without checking that the session is not referenced by some DLC. If the session is freed, that DLC would refer to deallocated memory, causing an oops later, as shown in this bug report: https://bugzilla.kernel.org/show_bug.cgi?id=15994 Signed-off-by: Lukas Turek <8an@praha12.net> Signed-off-by: Gustavo F. Padovan diff --git a/net/bluetooth/rfcomm/core.c b/net/bluetooth/rfcomm/core.c index ff8aaa7..6b83776 100644 --- a/net/bluetooth/rfcomm/core.c +++ b/net/bluetooth/rfcomm/core.c @@ -1164,7 +1164,8 @@ static int rfcomm_recv_ua(struct rfcomm_session *s, u8 dlci) * initiator rfcomm_process_rx already calls * rfcomm_session_put() */ if (s->sock->sk->sk_state != BT_CLOSED) - rfcomm_session_put(s); + if (list_empty(&s->dlcs)) + rfcomm_session_put(s); break; } } -- cgit v0.10.2 From 88644bb9fee591b2743a881923263bc28df4cded Mon Sep 17 00:00:00 2001 From: Johan Hedberg Date: Wed, 19 Jan 2011 12:06:48 +0530 Subject: Revert "Bluetooth: Update sec_level/auth_type for already existing connections" This reverts commit 045309820afe047920a50de25634dab46a1e851d. That commit is wrong for two reasons: - The conn->sec_level shouldn't be updated without performing authentication first (as it's supposed to represent the level of security that the existing connection has) - A higher auth_type value doesn't mean "more secure" like the commit seems to assume. E.g. dedicated bonding with MITM protection is 0x03 whereas general bonding without MITM protection is 0x04. hci_conn_auth already takes care of updating conn->auth_type so hci_connect doesn't need to do it. Signed-off-by: Johan Hedberg Acked-by: Marcel Holtmann Signed-off-by: Gustavo F. Padovan diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c index 6b90a41..65a3fb5 100644 --- a/net/bluetooth/hci_conn.c +++ b/net/bluetooth/hci_conn.c @@ -382,11 +382,6 @@ struct hci_conn *hci_connect(struct hci_dev *hdev, int type, bdaddr_t *dst, __u8 acl->sec_level = sec_level; acl->auth_type = auth_type; hci_acl_connect(acl); - } else { - if (acl->sec_level < sec_level) - acl->sec_level = sec_level; - if (acl->auth_type < auth_type) - acl->auth_type = auth_type; } if (type == ACL_LINK) -- cgit v0.10.2 From 65cf686ee102b7eb0477a4bab82ff227071a0258 Mon Sep 17 00:00:00 2001 From: Johan Hedberg Date: Wed, 19 Jan 2011 12:06:49 +0530 Subject: Bluetooth: Fix MITM protection requirement preservation If an existing connection has a MITM protection requirement (the first bit of the auth_type) then that requirement should not be cleared by new sockets that reuse the ACL but don't have that requirement. Signed-off-by: Johan Hedberg Acked-by: Marcel Holtmann Signed-off-by: Gustavo F. Padovan diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c index 65a3fb5..fe712a8 100644 --- a/net/bluetooth/hci_conn.c +++ b/net/bluetooth/hci_conn.c @@ -442,6 +442,9 @@ static int hci_conn_auth(struct hci_conn *conn, __u8 sec_level, __u8 auth_type) else if (conn->link_mode & HCI_LM_AUTH) return 1; + /* Make sure we preserve an existing MITM requirement*/ + auth_type |= (conn->auth_type & 0x01); + conn->auth_type = auth_type; if (!test_and_set_bit(HCI_CONN_AUTH_PEND, &conn->pend)) { -- cgit v0.10.2 From 8556edd32f01c50a3c99e44dc2c3b1252ea59605 Mon Sep 17 00:00:00 2001 From: Johan Hedberg Date: Wed, 19 Jan 2011 12:06:50 +0530 Subject: Bluetooth: Create a unified auth_type evaluation function The logic for determining the needed auth_type for an L2CAP socket is rather complicated and has so far been duplicated in l2cap_check_security as well as l2cap_do_connect. Additionally the l2cap_check_security code was completely missing the handling of SOCK_RAW type sockets. This patch creates a unified function for the evaluation and makes l2cap_do_connect and l2cap_check_security use that function. Signed-off-by: Johan Hedberg Acked-by: Marcel Holtmann Signed-off-by: Gustavo F. Padovan diff --git a/net/bluetooth/l2cap.c b/net/bluetooth/l2cap.c index 4fd88eb..ae227bf 100644 --- a/net/bluetooth/l2cap.c +++ b/net/bluetooth/l2cap.c @@ -305,33 +305,44 @@ static void l2cap_chan_del(struct sock *sk, int err) } } -/* Service level security */ -static inline int l2cap_check_security(struct sock *sk) +static inline u8 l2cap_get_auth_type(struct sock *sk) { - struct l2cap_conn *conn = l2cap_pi(sk)->conn; - __u8 auth_type; + if (sk->sk_type == SOCK_RAW) { + switch (l2cap_pi(sk)->sec_level) { + case BT_SECURITY_HIGH: + return HCI_AT_DEDICATED_BONDING_MITM; + case BT_SECURITY_MEDIUM: + return HCI_AT_DEDICATED_BONDING; + default: + return HCI_AT_NO_BONDING; + } + } else if (l2cap_pi(sk)->psm == cpu_to_le16(0x0001)) { + if (l2cap_pi(sk)->sec_level == BT_SECURITY_LOW) + l2cap_pi(sk)->sec_level = BT_SECURITY_SDP; - if (l2cap_pi(sk)->psm == cpu_to_le16(0x0001)) { if (l2cap_pi(sk)->sec_level == BT_SECURITY_HIGH) - auth_type = HCI_AT_NO_BONDING_MITM; + return HCI_AT_NO_BONDING_MITM; else - auth_type = HCI_AT_NO_BONDING; - - if (l2cap_pi(sk)->sec_level == BT_SECURITY_LOW) - l2cap_pi(sk)->sec_level = BT_SECURITY_SDP; + return HCI_AT_NO_BONDING; } else { switch (l2cap_pi(sk)->sec_level) { case BT_SECURITY_HIGH: - auth_type = HCI_AT_GENERAL_BONDING_MITM; - break; + return HCI_AT_GENERAL_BONDING_MITM; case BT_SECURITY_MEDIUM: - auth_type = HCI_AT_GENERAL_BONDING; - break; + return HCI_AT_GENERAL_BONDING; default: - auth_type = HCI_AT_NO_BONDING; - break; + return HCI_AT_NO_BONDING; } } +} + +/* Service level security */ +static inline int l2cap_check_security(struct sock *sk) +{ + struct l2cap_conn *conn = l2cap_pi(sk)->conn; + __u8 auth_type; + + auth_type = l2cap_get_auth_type(sk); return hci_conn_security(conn->hcon, l2cap_pi(sk)->sec_level, auth_type); @@ -1068,39 +1079,7 @@ static int l2cap_do_connect(struct sock *sk) err = -ENOMEM; - if (sk->sk_type == SOCK_RAW) { - switch (l2cap_pi(sk)->sec_level) { - case BT_SECURITY_HIGH: - auth_type = HCI_AT_DEDICATED_BONDING_MITM; - break; - case BT_SECURITY_MEDIUM: - auth_type = HCI_AT_DEDICATED_BONDING; - break; - default: - auth_type = HCI_AT_NO_BONDING; - break; - } - } else if (l2cap_pi(sk)->psm == cpu_to_le16(0x0001)) { - if (l2cap_pi(sk)->sec_level == BT_SECURITY_HIGH) - auth_type = HCI_AT_NO_BONDING_MITM; - else - auth_type = HCI_AT_NO_BONDING; - - if (l2cap_pi(sk)->sec_level == BT_SECURITY_LOW) - l2cap_pi(sk)->sec_level = BT_SECURITY_SDP; - } else { - switch (l2cap_pi(sk)->sec_level) { - case BT_SECURITY_HIGH: - auth_type = HCI_AT_GENERAL_BONDING_MITM; - break; - case BT_SECURITY_MEDIUM: - auth_type = HCI_AT_GENERAL_BONDING; - break; - default: - auth_type = HCI_AT_NO_BONDING; - break; - } - } + auth_type = l2cap_get_auth_type(sk); hcon = hci_connect(hdev, ACL_LINK, dst, l2cap_pi(sk)->sec_level, auth_type); -- cgit v0.10.2 From d00ef24fc2923b65fdd440dc6445903e965841ac Mon Sep 17 00:00:00 2001 From: Johan Hedberg Date: Wed, 19 Jan 2011 12:06:51 +0530 Subject: Bluetooth: Fix authentication request for L2CAP raw sockets When there is an existing connection l2cap_check_security needs to be called to ensure that the security level of the new socket is fulfilled. Normally l2cap_do_start takes care of this, but that function doesn't get called for SOCK_RAW type sockets. This patch adds the necessary l2cap_check_security call to the appropriate branch in l2cap_do_connect. Signed-off-by: Johan Hedberg Acked-by: Marcel Holtmann Signed-off-by: Gustavo F. Padovan diff --git a/net/bluetooth/l2cap.c b/net/bluetooth/l2cap.c index ae227bf..7550abb 100644 --- a/net/bluetooth/l2cap.c +++ b/net/bluetooth/l2cap.c @@ -1106,7 +1106,8 @@ static int l2cap_do_connect(struct sock *sk) if (sk->sk_type != SOCK_SEQPACKET && sk->sk_type != SOCK_STREAM) { l2cap_sock_clear_timer(sk); - sk->sk_state = BT_CONNECTED; + if (l2cap_check_security(sk)) + sk->sk_state = BT_CONNECTED; } else l2cap_do_start(sk); } -- cgit v0.10.2 From 765c2a964b49bd06b61a52991519281c85d82b67 Mon Sep 17 00:00:00 2001 From: Johan Hedberg Date: Wed, 19 Jan 2011 12:06:52 +0530 Subject: Bluetooth: Fix race condition with conn->sec_level The conn->sec_level value is supposed to represent the current level of security that the connection has. However, by assigning to it before requesting authentication it will have the wrong value during the authentication procedure. To fix this a pending_sec_level variable is added which is used to track the desired security level while making sure that sec_level always represents the current level of security. Signed-off-by: Johan Hedberg Signed-off-by: Gustavo F. Padovan diff --git a/include/net/bluetooth/hci_core.h b/include/net/bluetooth/hci_core.h index a29feb0..d2cf884 100644 --- a/include/net/bluetooth/hci_core.h +++ b/include/net/bluetooth/hci_core.h @@ -184,6 +184,7 @@ struct hci_conn { __u32 link_mode; __u8 auth_type; __u8 sec_level; + __u8 pending_sec_level; __u8 power_save; __u16 disc_timeout; unsigned long pend; diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c index fe712a8..99cd8d9 100644 --- a/net/bluetooth/hci_conn.c +++ b/net/bluetooth/hci_conn.c @@ -379,7 +379,8 @@ struct hci_conn *hci_connect(struct hci_dev *hdev, int type, bdaddr_t *dst, __u8 hci_conn_hold(acl); if (acl->state == BT_OPEN || acl->state == BT_CLOSED) { - acl->sec_level = sec_level; + acl->sec_level = BT_SECURITY_LOW; + acl->pending_sec_level = sec_level; acl->auth_type = auth_type; hci_acl_connect(acl); } @@ -437,8 +438,11 @@ static int hci_conn_auth(struct hci_conn *conn, __u8 sec_level, __u8 auth_type) { BT_DBG("conn %p", conn); + if (conn->pending_sec_level > sec_level) + sec_level = conn->pending_sec_level; + if (sec_level > conn->sec_level) - conn->sec_level = sec_level; + conn->pending_sec_level = sec_level; else if (conn->link_mode & HCI_LM_AUTH) return 1; diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c index 3810017..a290854 100644 --- a/net/bluetooth/hci_event.c +++ b/net/bluetooth/hci_event.c @@ -692,13 +692,13 @@ static int hci_outgoing_auth_needed(struct hci_dev *hdev, if (conn->state != BT_CONFIG || !conn->out) return 0; - if (conn->sec_level == BT_SECURITY_SDP) + if (conn->pending_sec_level == BT_SECURITY_SDP) return 0; /* Only request authentication for SSP connections or non-SSP * devices with sec_level HIGH */ if (!(hdev->ssp_mode > 0 && conn->ssp_mode > 0) && - conn->sec_level != BT_SECURITY_HIGH) + conn->pending_sec_level != BT_SECURITY_HIGH) return 0; return 1; @@ -1095,9 +1095,10 @@ static inline void hci_auth_complete_evt(struct hci_dev *hdev, struct sk_buff *s conn = hci_conn_hash_lookup_handle(hdev, __le16_to_cpu(ev->handle)); if (conn) { - if (!ev->status) + if (!ev->status) { conn->link_mode |= HCI_LM_AUTH; - else + conn->sec_level = conn->pending_sec_level; + } else conn->sec_level = BT_SECURITY_LOW; clear_bit(HCI_CONN_AUTH_PEND, &conn->pend); -- cgit v0.10.2 From 239712ebb2b4750431980d33993ea05c6ac7ff65 Mon Sep 17 00:00:00 2001 From: Wey-Yi Guy Date: Thu, 20 Jan 2011 08:08:04 -0800 Subject: iwlwifi: don't read sku information from EEPROM for 4965 For all the new devices, the sku information should read from EEPROM but for legacy devices such as 4965, appearly the EEPROM does not contain the necessary information. so skip the read from EEPROM and go back to use software configuration. Reported-by: Helmut Schaa Signed-off-by: Wey-Yi Guy Tested-by: Helmut Schaa Signed-off-by: John W. Linville diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c index 3f1e5f1..91a9f52 100644 --- a/drivers/net/wireless/iwlwifi/iwl-4965.c +++ b/drivers/net/wireless/iwlwifi/iwl-4965.c @@ -2624,6 +2624,7 @@ struct iwl_cfg iwl4965_agn_cfg = { .fw_name_pre = IWL4965_FW_PRE, .ucode_api_max = IWL4965_UCODE_API_MAX, .ucode_api_min = IWL4965_UCODE_API_MIN, + .sku = IWL_SKU_A|IWL_SKU_G|IWL_SKU_N, .valid_tx_ant = ANT_AB, .valid_rx_ant = ANT_ABC, .eeprom_ver = EEPROM_4965_EEPROM_VERSION, diff --git a/drivers/net/wireless/iwlwifi/iwl-agn-eeprom.c b/drivers/net/wireless/iwlwifi/iwl-agn-eeprom.c index 14ceb4d..27b5a3e 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn-eeprom.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn-eeprom.c @@ -152,11 +152,14 @@ int iwl_eeprom_check_sku(struct iwl_priv *priv) eeprom_sku = iwl_eeprom_query16(priv, EEPROM_SKU_CAP); - priv->cfg->sku = ((eeprom_sku & EEPROM_SKU_CAP_BAND_SELECTION) >> + if (!priv->cfg->sku) { + /* not using sku overwrite */ + priv->cfg->sku = + ((eeprom_sku & EEPROM_SKU_CAP_BAND_SELECTION) >> EEPROM_SKU_CAP_BAND_POS); - if (eeprom_sku & EEPROM_SKU_CAP_11N_ENABLE) - priv->cfg->sku |= IWL_SKU_N; - + if (eeprom_sku & EEPROM_SKU_CAP_11N_ENABLE) + priv->cfg->sku |= IWL_SKU_N; + } if (!priv->cfg->sku) { IWL_ERR(priv, "Invalid device sku\n"); return -EINVAL; -- cgit v0.10.2 From 6f4810101a629b31b5427872a09ea092cfc5c4bd Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Thu, 20 Jan 2011 17:47:39 -0800 Subject: ath9k_hw: disabled PAPRD for AR9003 AR9003's PAPRD was enabled prematurely, and is causing some large discrepancies on throughput and network connectivity. For example downlink (RX) throughput against an AR9280 AP can vary widlely from 43-73 Mbit/s while disabling this gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup. Cc: stable@kernel.org Cc: Paul Shaw Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c index 1afb8bb..9f01e50 100644 --- a/drivers/net/wireless/ath/ath9k/hw.c +++ b/drivers/net/wireless/ath/ath9k/hw.c @@ -369,6 +369,9 @@ static void ath9k_hw_init_config(struct ath_hw *ah) else ah->config.ht_enable = 0; + /* PAPRD needs some more work to be enabled */ + ah->config.paprd_disable = 1; + ah->config.rx_intr_mitigation = true; ah->config.pcieSerDesWrite = true; @@ -1933,7 +1936,8 @@ int ath9k_hw_fill_cap_info(struct ath_hw *ah) pCap->rx_status_len = sizeof(struct ar9003_rxs); pCap->tx_desc_len = sizeof(struct ar9003_txc); pCap->txs_len = sizeof(struct ar9003_txs); - if (ah->eep_ops->get_eeprom(ah, EEP_PAPRD)) + if (!ah->config.paprd_disable && + ah->eep_ops->get_eeprom(ah, EEP_PAPRD)) pCap->hw_caps |= ATH9K_HW_CAP_PAPRD; } else { pCap->tx_desc_len = sizeof(struct ath_desc); diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h index 5a3dfec..ea9fde6 100644 --- a/drivers/net/wireless/ath/ath9k/hw.h +++ b/drivers/net/wireless/ath/ath9k/hw.h @@ -225,6 +225,7 @@ struct ath9k_ops_config { u32 pcie_waen; u8 analog_shiftreg; u8 ht_enable; + u8 paprd_disable; u32 ofdm_trig_low; u32 ofdm_trig_high; u32 cck_trig_high; -- cgit v0.10.2 From 783cd01e140d9db5c2d2279a96b81e16f9d81fef Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Fri, 21 Jan 2011 18:52:38 +0100 Subject: ath9k: add missing ps wakeup/restore calls There are several places where ath_reset() was called without proper calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls directly to ath_reset and drop them from callers where it makes sense. Also add them to the config callback around ath_update_txpow to fix a crash that happens when the tx power changed before any vif is brought up. Signed-off-by: Felix Fietkau Cc: stable@kernel.org Signed-off-by: John W. Linville diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index f90a6ca..c79c97b 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -592,14 +592,12 @@ void ath9k_tasklet(unsigned long data) u32 status = sc->intrstatus; u32 rxmask; - ath9k_ps_wakeup(sc); - if (status & ATH9K_INT_FATAL) { ath_reset(sc, true); - ath9k_ps_restore(sc); return; } + ath9k_ps_wakeup(sc); spin_lock(&sc->sc_pcu_lock); if (!ath9k_hw_check_alive(ah)) @@ -969,6 +967,7 @@ int ath_reset(struct ath_softc *sc, bool retry_tx) /* Stop ANI */ del_timer_sync(&common->ani.timer); + ath9k_ps_wakeup(sc); spin_lock_bh(&sc->sc_pcu_lock); ieee80211_stop_queues(hw); @@ -1015,6 +1014,7 @@ int ath_reset(struct ath_softc *sc, bool retry_tx) /* Start ANI */ ath_start_ani(common); + ath9k_ps_restore(sc); return r; } @@ -1701,7 +1701,9 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed) skip_chan_change: if (changed & IEEE80211_CONF_CHANGE_POWER) { sc->config.txpowlimit = 2 * conf->power_level; + ath9k_ps_wakeup(sc); ath_update_txpow(sc); + ath9k_ps_restore(sc); } spin_lock_bh(&sc->wiphy_lock); diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c index 332d1fe..33a37ed 100644 --- a/drivers/net/wireless/ath/ath9k/xmit.c +++ b/drivers/net/wireless/ath/ath9k/xmit.c @@ -2113,9 +2113,7 @@ static void ath_tx_complete_poll_work(struct work_struct *work) if (needreset) { ath_dbg(ath9k_hw_common(sc->sc_ah), ATH_DBG_RESET, "tx hung, resetting the chip\n"); - ath9k_ps_wakeup(sc); ath_reset(sc, true); - ath9k_ps_restore(sc); } ieee80211_queue_delayed_work(sc->hw, &sc->tx_complete_work, -- cgit v0.10.2 From bdc4bf652bc0271ba8f1f25bbd3dbac90bead44e Mon Sep 17 00:00:00 2001 From: Jesper Juhl Date: Fri, 21 Jan 2011 13:40:54 -0600 Subject: rtlwifi: Fix possible NULL dereference In drivers/net/wireless/rtlwifi/pci.c::_rtl_pci_rx_interrupt() we call dev_alloc_skb(), which may fail and return NULL, but we do not check the returned value against NULL before dereferencing the returned pointer. This may lead to a NULL pointer dereference which means we'll crash - not good. In a separate call to dev_alloc_skb(), the debug level is changed so that the failure message will always be logged. Signed-off-by: Jesper Juhl Signed-off-by: Larry Finger Signed-off-by: John W. Linville diff --git a/drivers/net/wireless/rtlwifi/pci.c b/drivers/net/wireless/rtlwifi/pci.c index 0fa36aa..1758d44 100644 --- a/drivers/net/wireless/rtlwifi/pci.c +++ b/drivers/net/wireless/rtlwifi/pci.c @@ -619,6 +619,13 @@ static void _rtl_pci_rx_interrupt(struct ieee80211_hw *hw) struct sk_buff *uskb = NULL; u8 *pdata; uskb = dev_alloc_skb(skb->len + 128); + if (!uskb) { + RT_TRACE(rtlpriv, + (COMP_INTR | COMP_RECV), + DBG_EMERG, + ("can't alloc rx skb\n")); + goto done; + } memcpy(IEEE80211_SKB_RXCB(uskb), &rx_status, sizeof(rx_status)); @@ -641,7 +648,7 @@ static void _rtl_pci_rx_interrupt(struct ieee80211_hw *hw) new_skb = dev_alloc_skb(rtlpci->rxbuffersize); if (unlikely(!new_skb)) { RT_TRACE(rtlpriv, (COMP_INTR | COMP_RECV), - DBG_DMESG, + DBG_EMERG, ("can't alloc skb for rx\n")); goto done; } @@ -1066,9 +1073,9 @@ static int _rtl_pci_init_rx_ring(struct ieee80211_hw *hw) struct sk_buff *skb = dev_alloc_skb(rtlpci->rxbuffersize); u32 bufferaddress; - entry = &rtlpci->rx_ring[rx_queue_idx].desc[i]; if (!skb) return 0; + entry = &rtlpci->rx_ring[rx_queue_idx].desc[i]; /*skb->dev = dev; */ -- cgit v0.10.2 From 0909c1ec6f016b3f580fa2f4630659a5874a8ef8 Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Thu, 6 Jan 2011 09:58:42 +0100 Subject: can: at91_can: clean up usage of AT91_MB_RX_FIRST and AT91_MB_RX_NUM This patch cleans up the usage of two macros which specify the mailbox usage. AT91_MB_RX_FIRST and AT91_MB_RX_NUM define the first and the number of RX mailboxes. The current driver uses these variables in an unclean way; assuming that AT91_MB_RX_FIRST is 0; This patch cleans up the usage of these macros, no longer assuming AT91_MB_RX_FIRST == 0. Signed-off-by: Marc Kleine-Budde Acked-by: Wolfgang Grandegger diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c index 7ef83d0..892c3d8 100644 --- a/drivers/net/can/at91_can.c +++ b/drivers/net/can/at91_can.c @@ -2,7 +2,7 @@ * at91_can.c - CAN network driver for AT91 SoC CAN controller * * (C) 2007 by Hans J. Koch - * (C) 2008, 2009, 2010 by Marc Kleine-Budde + * (C) 2008, 2009, 2010, 2011 by Marc Kleine-Budde * * This software may be distributed under the terms of the GNU General * Public License ("GPL") version 2 as distributed in the 'COPYING' @@ -55,7 +55,8 @@ #define AT91_MB_RX_MASK(i) ((1 << (i)) - 1) #define AT91_MB_RX_SPLIT 8 #define AT91_MB_RX_LOW_LAST (AT91_MB_RX_SPLIT - 1) -#define AT91_MB_RX_LOW_MASK (AT91_MB_RX_MASK(AT91_MB_RX_SPLIT)) +#define AT91_MB_RX_LOW_MASK (AT91_MB_RX_MASK(AT91_MB_RX_SPLIT) & \ + ~AT91_MB_RX_MASK(AT91_MB_RX_FIRST)) #define AT91_MB_TX_NUM (1 << AT91_MB_TX_SHIFT) #define AT91_MB_TX_FIRST (AT91_MB_RX_LAST + 1) @@ -254,7 +255,8 @@ static void at91_setup_mailboxes(struct net_device *dev) set_mb_mode_prio(priv, i, AT91_MB_MODE_TX, 0); /* Reset tx and rx helper pointers */ - priv->tx_next = priv->tx_echo = priv->rx_next = 0; + priv->tx_next = priv->tx_echo = 0; + priv->rx_next = AT91_MB_RX_FIRST; } static int at91_set_bittiming(struct net_device *dev) @@ -590,10 +592,10 @@ static int at91_poll_rx(struct net_device *dev, int quota) "order of incoming frames cannot be guaranteed\n"); again: - for (mb = find_next_bit(addr, AT91_MB_RX_NUM, priv->rx_next); - mb < AT91_MB_RX_NUM && quota > 0; + for (mb = find_next_bit(addr, AT91_MB_RX_LAST + 1, priv->rx_next); + mb < AT91_MB_RX_LAST + 1 && quota > 0; reg_sr = at91_read(priv, AT91_SR), - mb = find_next_bit(addr, AT91_MB_RX_NUM, ++priv->rx_next)) { + mb = find_next_bit(addr, AT91_MB_RX_LAST + 1, ++priv->rx_next)) { at91_read_msg(dev, mb); /* reactivate mailboxes */ @@ -610,8 +612,8 @@ static int at91_poll_rx(struct net_device *dev, int quota) /* upper group completed, look again in lower */ if (priv->rx_next > AT91_MB_RX_LOW_LAST && - quota > 0 && mb >= AT91_MB_RX_NUM) { - priv->rx_next = 0; + quota > 0 && mb > AT91_MB_RX_LAST) { + priv->rx_next = AT91_MB_RX_FIRST; goto again; } -- cgit v0.10.2 From 9e0a2d1ca3de6e284e99ad5cae1ae33ecb74c479 Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Sun, 9 Jan 2011 22:46:25 +0100 Subject: can: at91_can: don't use mailbox 0 Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in "AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox 0 may be send under certain conditions (even if disabled or in rx mode). The workaround in the errata suggests not to use the mailbox and load it with a unused identifier. This patch implements the first part of the workaround, it updates AT91_MB_RX_NUM and AT91_MB_RX_FIRST (and the inline documentation) so that mailbox 0 stays unused. Signed-off-by: Marc Kleine-Budde Acked-by: Wolfgang Grandegger Acked-by: Kurt Van Dijck diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c index 892c3d8..16e45a5 100644 --- a/drivers/net/can/at91_can.c +++ b/drivers/net/can/at91_can.c @@ -40,16 +40,16 @@ #include -#define AT91_NAPI_WEIGHT 12 +#define AT91_NAPI_WEIGHT 11 /* * RX/TX Mailbox split * don't dare to touch */ -#define AT91_MB_RX_NUM 12 +#define AT91_MB_RX_NUM 11 #define AT91_MB_TX_SHIFT 2 -#define AT91_MB_RX_FIRST 0 +#define AT91_MB_RX_FIRST 1 #define AT91_MB_RX_LAST (AT91_MB_RX_FIRST + AT91_MB_RX_NUM - 1) #define AT91_MB_RX_MASK(i) ((1 << (i)) - 1) @@ -236,10 +236,14 @@ static void at91_setup_mailboxes(struct net_device *dev) unsigned int i; /* - * The first 12 mailboxes are used as a reception FIFO. The - * last mailbox is configured with overwrite option. The - * overwrite flag indicates a FIFO overflow. + * Due to a chip bug (errata 50.2.6.3 & 50.3.5.3) the first + * mailbox is disabled. The next 11 mailboxes are used as a + * reception FIFO. The last mailbox is configured with + * overwrite option. The overwrite flag indicates a FIFO + * overflow. */ + for (i = 0; i < AT91_MB_RX_FIRST; i++) + set_mb_mode(priv, i, AT91_MB_MODE_DISABLED); for (i = AT91_MB_RX_FIRST; i < AT91_MB_RX_LAST; i++) set_mb_mode(priv, i, AT91_MB_MODE_RX); set_mb_mode(priv, AT91_MB_RX_LAST, AT91_MB_MODE_RX_OVRWR); @@ -541,27 +545,31 @@ static void at91_read_msg(struct net_device *dev, unsigned int mb) * * Theory of Operation: * - * 12 of the 16 mailboxes on the chip are reserved for RX. we split - * them into 2 groups. The lower group holds 8 and upper 4 mailboxes. + * 11 of the 16 mailboxes on the chip are reserved for RX. we split + * them into 2 groups. The lower group holds 7 and upper 4 mailboxes. * * Like it or not, but the chip always saves a received CAN message * into the first free mailbox it finds (starting with the * lowest). This makes it very difficult to read the messages in the * right order from the chip. This is how we work around that problem: * - * The first message goes into mb nr. 0 and issues an interrupt. All + * The first message goes into mb nr. 1 and issues an interrupt. All * rx ints are disabled in the interrupt handler and a napi poll is * scheduled. We read the mailbox, but do _not_ reenable the mb (to * receive another message). * * lower mbxs upper - * ______^______ __^__ - * / \ / \ + * ____^______ __^__ + * / \ / \ * +-+-+-+-+-+-+-+-++-+-+-+-+ - * |x|x|x|x|x|x|x|x|| | | | | + * | |x|x|x|x|x|x|x|| | | | | * +-+-+-+-+-+-+-+-++-+-+-+-+ * 0 0 0 0 0 0 0 0 0 0 1 1 \ mail * 0 1 2 3 4 5 6 7 8 9 0 1 / box + * ^ + * | + * \ + * unused, due to chip bug * * The variable priv->rx_next points to the next mailbox to read a * message from. As long we're in the lower mailboxes we just read the -- cgit v0.10.2 From 3a5655a5b545e9647c3437473ee3d815fe1b9050 Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Mon, 10 Jan 2011 20:44:22 +0100 Subject: can: at91_can: make can_id of mailbox 0 configurable Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in "AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the contents of mailbox 0 may be send under certain conditions (even if disabled or in rx mode). The workaround in the errata suggests not to use the mailbox and load it with an unused identifier. This patch implements the second part of the workaround. A sysfs entry "mb0_id" is introduced. While the interface is down it can be used to configure the can_id of mailbox 0. The default value id 0x7ff. In order to use an extended can_id add the CAN_EFF_FLAG (0x80000000U) to the can_id. Example: - standard id 0x7ff: echo 0x7ff > /sys/class/net/can0/mb0_id - extended id 0x1fffffff: echo 0x9fffffff > /sys/class/net/can0/mb0_id Signed-off-by: Marc Kleine-Budde Acked-by: Wolfgang Grandegger Acked-by: Kurt Van Dijck For the Documentation-part: Acked-by: Wolfram Sang diff --git a/Documentation/ABI/testing/sysfs-platform-at91 b/Documentation/ABI/testing/sysfs-platform-at91 new file mode 100644 index 0000000..4cc6a86 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-platform-at91 @@ -0,0 +1,25 @@ +What: /sys/devices/platform/at91_can/net//mb0_id +Date: January 2011 +KernelVersion: 2.6.38 +Contact: Marc Kleine-Budde +Description: + Value representing the can_id of mailbox 0. + + Default: 0x7ff (standard frame) + + Due to a chip bug (errata 50.2.6.3 & 50.3.5.3 in + "AT91SAM9263 Preliminary 6249H-ATARM-27-Jul-09") the + contents of mailbox 0 may be send under certain + conditions (even if disabled or in rx mode). + + The workaround in the errata suggests not to use the + mailbox and load it with an unused identifier. + + In order to use an extended can_id add the + CAN_EFF_FLAG (0x80000000U) to the can_id. Example: + + - standard id 0x7ff: + echo 0x7ff > /sys/class/net/can0/mb0_id + + - extended id 0x1fffffff: + echo 0x9fffffff > /sys/class/net/can0/mb0_id diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c index 16e45a5..2532b96 100644 --- a/drivers/net/can/at91_can.c +++ b/drivers/net/can/at91_can.c @@ -30,6 +30,7 @@ #include #include #include +#include #include #include #include @@ -169,6 +170,8 @@ struct at91_priv { struct clk *clk; struct at91_can_data *pdata; + + canid_t mb0_id; }; static struct can_bittiming_const at91_bittiming_const = { @@ -221,6 +224,18 @@ static inline void set_mb_mode(const struct at91_priv *priv, unsigned int mb, set_mb_mode_prio(priv, mb, mode, 0); } +static inline u32 at91_can_id_to_reg_mid(canid_t can_id) +{ + u32 reg_mid; + + if (can_id & CAN_EFF_FLAG) + reg_mid = (can_id & CAN_EFF_MASK) | AT91_MID_MIDE; + else + reg_mid = (can_id & CAN_SFF_MASK) << 18; + + return reg_mid; +} + /* * Swtich transceiver on or off */ @@ -234,6 +249,7 @@ static void at91_setup_mailboxes(struct net_device *dev) { struct at91_priv *priv = netdev_priv(dev); unsigned int i; + u32 reg_mid; /* * Due to a chip bug (errata 50.2.6.3 & 50.3.5.3) the first @@ -242,8 +258,13 @@ static void at91_setup_mailboxes(struct net_device *dev) * overwrite option. The overwrite flag indicates a FIFO * overflow. */ - for (i = 0; i < AT91_MB_RX_FIRST; i++) + reg_mid = at91_can_id_to_reg_mid(priv->mb0_id); + for (i = 0; i < AT91_MB_RX_FIRST; i++) { set_mb_mode(priv, i, AT91_MB_MODE_DISABLED); + at91_write(priv, AT91_MID(i), reg_mid); + at91_write(priv, AT91_MCR(i), 0x0); /* clear dlc */ + } + for (i = AT91_MB_RX_FIRST; i < AT91_MB_RX_LAST; i++) set_mb_mode(priv, i, AT91_MB_MODE_RX); set_mb_mode(priv, AT91_MB_RX_LAST, AT91_MB_MODE_RX_OVRWR); @@ -378,12 +399,7 @@ static netdev_tx_t at91_start_xmit(struct sk_buff *skb, struct net_device *dev) netdev_err(dev, "BUG! TX buffer full when queue awake!\n"); return NETDEV_TX_BUSY; } - - if (cf->can_id & CAN_EFF_FLAG) - reg_mid = (cf->can_id & CAN_EFF_MASK) | AT91_MID_MIDE; - else - reg_mid = (cf->can_id & CAN_SFF_MASK) << 18; - + reg_mid = at91_can_id_to_reg_mid(cf->can_id); reg_mcr = ((cf->can_id & CAN_RTR_FLAG) ? AT91_MCR_MRTR : 0) | (cf->can_dlc << 16) | AT91_MCR_MTCR; @@ -1047,6 +1063,64 @@ static const struct net_device_ops at91_netdev_ops = { .ndo_start_xmit = at91_start_xmit, }; +static ssize_t at91_sysfs_show_mb0_id(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct at91_priv *priv = netdev_priv(to_net_dev(dev)); + + if (priv->mb0_id & CAN_EFF_FLAG) + return snprintf(buf, PAGE_SIZE, "0x%08x\n", priv->mb0_id); + else + return snprintf(buf, PAGE_SIZE, "0x%03x\n", priv->mb0_id); +} + +static ssize_t at91_sysfs_set_mb0_id(struct device *dev, + struct device_attribute *attr, const char *buf, size_t count) +{ + struct net_device *ndev = to_net_dev(dev); + struct at91_priv *priv = netdev_priv(ndev); + unsigned long can_id; + ssize_t ret; + int err; + + rtnl_lock(); + + if (ndev->flags & IFF_UP) { + ret = -EBUSY; + goto out; + } + + err = strict_strtoul(buf, 0, &can_id); + if (err) { + ret = err; + goto out; + } + + if (can_id & CAN_EFF_FLAG) + can_id &= CAN_EFF_MASK | CAN_EFF_FLAG; + else + can_id &= CAN_SFF_MASK; + + priv->mb0_id = can_id; + ret = count; + + out: + rtnl_unlock(); + return ret; +} + +static DEVICE_ATTR(mb0_id, S_IWUGO | S_IRUGO, + at91_sysfs_show_mb0_id, at91_sysfs_set_mb0_id); + +static struct attribute *at91_sysfs_attrs[] = { + &dev_attr_mb0_id.attr, + NULL, +}; + +static struct attribute_group at91_sysfs_attr_group = { + .attrs = at91_sysfs_attrs, +}; + static int __devinit at91_can_probe(struct platform_device *pdev) { struct net_device *dev; @@ -1092,6 +1166,7 @@ static int __devinit at91_can_probe(struct platform_device *pdev) dev->netdev_ops = &at91_netdev_ops; dev->irq = irq; dev->flags |= IFF_ECHO; + dev->sysfs_groups[0] = &at91_sysfs_attr_group; priv = netdev_priv(dev); priv->can.clock.freq = clk_get_rate(clk); @@ -1103,6 +1178,7 @@ static int __devinit at91_can_probe(struct platform_device *pdev) priv->dev = dev; priv->clk = clk; priv->pdata = pdev->dev.platform_data; + priv->mb0_id = 0x7ff; netif_napi_add(dev, &priv->napi, at91_poll, AT91_NAPI_WEIGHT); -- cgit v0.10.2 From d1dc7abf2fafa34b0ffcd070fd59405aa9c0a4d8 Mon Sep 17 00:00:00 2001 From: Michal Schmidt Date: Mon, 24 Jan 2011 12:08:48 +0000 Subject: GRO: fix merging a paged skb after non-paged skbs Suppose that several linear skbs of the same flow were received by GRO. They were thus merged into one skb with a frag_list. Then a new skb of the same flow arrives, but it is a paged skb with data starting in its frags[]. Before adding the skb to the frag_list skb_gro_receive() will of course adjust the skb to throw away the headers. It correctly modifies the page_offset and size of the frag, but it leaves incorrect information in the skb: ->data_len is not decreased at all. ->len is decreased only by headlen, as if no change were done to the frag. Later in a receiving process this causes skb_copy_datagram_iovec() to return -EFAULT and this is seen in userspace as the result of the recv() syscall. In practice the bug can be reproduced with the sfc driver. By default the driver uses an adaptive scheme when it switches between using napi_gro_receive() (with skbs) and napi_gro_frags() (with pages). The bug is reproduced when under rx load with enough successful GRO merging the driver decides to switch from the former to the latter. Manual control is also possible, so reproducing this is easy with netcat: - on machine1 (with sfc): nc -l 12345 > /dev/null - on machine2: nc machine1 12345 < /dev/zero - on machine1: echo 1 > /sys/module/sfc/parameters/rx_alloc_method # use skbs echo 2 > /sys/module/sfc/parameters/rx_alloc_method # use pages - See that nc has quit suddenly. [v2: Modified by Eric Dumazet to avoid advancing skb->data past the end and to use a temporary variable.] Signed-off-by: Michal Schmidt Acked-by: Eric Dumazet Signed-off-by: David S. Miller diff --git a/net/core/skbuff.c b/net/core/skbuff.c index d31bb36..7cd1bc8 100644 --- a/net/core/skbuff.c +++ b/net/core/skbuff.c @@ -2744,8 +2744,12 @@ int skb_gro_receive(struct sk_buff **head, struct sk_buff *skb) merge: if (offset > headlen) { - skbinfo->frags[0].page_offset += offset - headlen; - skbinfo->frags[0].size -= offset - headlen; + unsigned int eat = offset - headlen; + + skbinfo->frags[0].page_offset += eat; + skbinfo->frags[0].size -= eat; + skb->data_len -= eat; + skb->len -= eat; offset = headlen; } -- cgit v0.10.2 From 3408404a4c2a4eead9d73b0bbbfe3f225b65f492 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 24 Jan 2011 14:37:46 -0800 Subject: inetpeer: Use correct AVL tree base pointer in inet_getpeer(). Family was hard-coded to AF_INET but should be daddr->family. This fixes crashes when unlinking ipv6 peer entries, since the unlink code was looking up the base pointer properly. Reported-by: Eric Dumazet Signed-off-by: David S. Miller diff --git a/net/ipv4/inetpeer.c b/net/ipv4/inetpeer.c index d9bc857..a96e656 100644 --- a/net/ipv4/inetpeer.c +++ b/net/ipv4/inetpeer.c @@ -475,7 +475,7 @@ static int cleanup_once(unsigned long ttl) struct inet_peer *inet_getpeer(struct inetpeer_addr *daddr, int create) { struct inet_peer __rcu **stack[PEER_MAXDEPTH], ***stackptr; - struct inet_peer_base *base = family_to_base(AF_INET); + struct inet_peer_base *base = family_to_base(daddr->family); struct inet_peer *p; /* Look up for the address quickly, lockless. -- cgit v0.10.2 From fd0273c5033630b8673554cd39660435d1ab2ac4 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Mon, 24 Jan 2011 14:41:20 -0800 Subject: tcp: fix bug in listening_get_next() commit a8b690f98baf9fb19 (tcp: Fix slowness in read /proc/net/tcp) introduced a bug in handling of SYN_RECV sockets. st->offset represents number of sockets found since beginning of listening_hash[st->bucket]. We should not reset st->offset when iterating through syn_table[st->sbucket], or else if more than ~25 sockets (if PAGE_SIZE=4096) are in SYN_RECV state, we exit from listening_get_next() with a too small st->offset Next time we enter tcp_seek_last_pos(), we are not able to seek past already found sockets. Reported-by: PK CC: Tom Herbert Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller diff --git a/net/ipv4/tcp_ipv4.c b/net/ipv4/tcp_ipv4.c index 856f684..02f583b 100644 --- a/net/ipv4/tcp_ipv4.c +++ b/net/ipv4/tcp_ipv4.c @@ -1994,7 +1994,6 @@ static void *listening_get_next(struct seq_file *seq, void *cur) } req = req->dl_next; } - st->offset = 0; if (++st->sbucket >= icsk->icsk_accept_queue.listen_opt->nr_table_entries) break; get_req: -- cgit v0.10.2 From 3dce38a02d6370dca690cd923619d4b00024b723 Mon Sep 17 00:00:00 2001 From: John Fastabend Date: Fri, 21 Jan 2011 16:35:18 +0000 Subject: dcbnl: make get_app handling symmetric for IEEE and CEE DCBx The IEEE get/set app handlers use generic routines and do not require the net_device to implement the dcbnl_ops routines. This patch makes it symmetric so user space and drivers do not have to handle the CEE version and IEEE DCBx versions differently. Signed-off-by: John Fastabend Signed-off-by: David S. Miller diff --git a/net/dcb/dcbnl.c b/net/dcb/dcbnl.c index d900ab9..6b03f56 100644 --- a/net/dcb/dcbnl.c +++ b/net/dcb/dcbnl.c @@ -583,7 +583,7 @@ static int dcbnl_getapp(struct net_device *netdev, struct nlattr **tb, u8 up, idtype; int ret = -EINVAL; - if (!tb[DCB_ATTR_APP] || !netdev->dcbnl_ops->getapp) + if (!tb[DCB_ATTR_APP]) goto out; ret = nla_parse_nested(app_tb, DCB_APP_ATTR_MAX, tb[DCB_ATTR_APP], @@ -604,7 +604,16 @@ static int dcbnl_getapp(struct net_device *netdev, struct nlattr **tb, goto out; id = nla_get_u16(app_tb[DCB_APP_ATTR_ID]); - up = netdev->dcbnl_ops->getapp(netdev, idtype, id); + + if (netdev->dcbnl_ops->getapp) { + up = netdev->dcbnl_ops->getapp(netdev, idtype, id); + } else { + struct dcb_app app = { + .selector = idtype, + .protocol = id, + }; + up = dcb_getapp(netdev, &app); + } /* send this back */ dcbnl_skb = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_KERNEL); -- cgit v0.10.2 From d80bc0fd262ef840ed4e82593ad6416fa1ba3fc4 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 24 Jan 2011 16:01:58 -0800 Subject: ipv6: Always clone offlink routes. Do not handle PMTU vs. route lookup creation any differently wrt. offlink routes, always clone them. Reported-by: PK Signed-off-by: David S. Miller diff --git a/net/ipv6/route.c b/net/ipv6/route.c index 373bd04..1534508 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -72,8 +72,6 @@ #define RT6_TRACE(x...) do { ; } while (0) #endif -#define CLONE_OFFLINK_ROUTE 0 - static struct rt6_info * ip6_rt_copy(struct rt6_info *ort); static struct dst_entry *ip6_dst_check(struct dst_entry *dst, u32 cookie); static unsigned int ip6_default_advmss(const struct dst_entry *dst); @@ -738,13 +736,8 @@ restart: if (!rt->rt6i_nexthop && !(rt->rt6i_flags & RTF_NONEXTHOP)) nrt = rt6_alloc_cow(rt, &fl->fl6_dst, &fl->fl6_src); - else { -#if CLONE_OFFLINK_ROUTE + else nrt = rt6_alloc_clone(rt, &fl->fl6_dst); -#else - goto out2; -#endif - } dst_release(&rt->dst); rt = nrt ? : net->ipv6.ip6_null_entry; -- cgit v0.10.2 From b7c7d01aaed1f71d9afe815a569f0a81465a1744 Mon Sep 17 00:00:00 2001 From: Eugene Teo Date: Mon, 24 Jan 2011 21:05:17 -0800 Subject: net: clear heap allocation for ethtool_get_regs() There is a conflict between commit b00916b1 and a77f5db3. This patch resolves the conflict by clearing the heap allocation in ethtool_get_regs(). Cc: stable@kernel.org Signed-off-by: Eugene Teo Signed-off-by: David S. Miller diff --git a/net/core/ethtool.c b/net/core/ethtool.c index 1774178..ff23029 100644 --- a/net/core/ethtool.c +++ b/net/core/ethtool.c @@ -817,7 +817,7 @@ static int ethtool_get_regs(struct net_device *dev, char __user *useraddr) if (regs.len > reglen) regs.len = reglen; - regbuf = vmalloc(reglen); + regbuf = vzalloc(reglen); if (!regbuf) return -ENOMEM; -- cgit v0.10.2 From 7c8104774e59549c37dd1cb0a8ec4f131094664c Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Mon, 24 Jan 2011 12:59:02 +0000 Subject: bnx2: Always set ETH_FLAG_TXVLAN TSO does not work if the VLAN tag is in the packet (non-accelerated). We may be able to remove this restriction in future firmware. Reported-by: Eric Dumazet Signed-off-by: Michael Chan Signed-off-by: David S. Miller diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c index df99edf..99e7652 100644 --- a/drivers/net/bnx2.c +++ b/drivers/net/bnx2.c @@ -7553,6 +7553,10 @@ bnx2_set_flags(struct net_device *dev, u32 data) !(data & ETH_FLAG_RXVLAN)) return -EINVAL; + /* TSO with VLAN tag won't work with current firmware */ + if (!(data & ETH_FLAG_TXVLAN)) + return -EINVAL; + rc = ethtool_op_set_flags(dev, data, ETH_FLAG_RXHASH | ETH_FLAG_RXVLAN | ETH_FLAG_TXVLAN); if (rc) -- cgit v0.10.2 From 2321f3b4afc7c017f34b0cad0624b3b9ebdf2ba4 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Mon, 24 Jan 2011 23:19:10 -0800 Subject: pch_gbe: don't use flush_scheduled_work() Directly cancel adapter->reset_task instead of using to-be-deprecated flush_scheduled_work(). Signed-off-by: Tejun Heo Signed-off-by: David S. Miller diff --git a/drivers/net/pch_gbe/pch_gbe_main.c b/drivers/net/pch_gbe/pch_gbe_main.c index d735530..1bf1233 100644 --- a/drivers/net/pch_gbe/pch_gbe_main.c +++ b/drivers/net/pch_gbe/pch_gbe_main.c @@ -2247,7 +2247,7 @@ static void pch_gbe_remove(struct pci_dev *pdev) struct net_device *netdev = pci_get_drvdata(pdev); struct pch_gbe_adapter *adapter = netdev_priv(netdev); - flush_scheduled_work(); + cancel_work_sync(&adapter->reset_task); unregister_netdev(netdev); pch_gbe_hal_phy_hw_reset(&adapter->hw); -- cgit v0.10.2 From 986e3f6e2b4582d9a7e61de5090042d5af85da44 Mon Sep 17 00:00:00 2001 From: Jesper Juhl Date: Sun, 23 Jan 2011 12:19:55 +0000 Subject: USB NET KL5KUSB101: Fix mem leak in error path of kaweth_download_firmware() We will leak the storage allocated by request_firmware() if the size of the firmware is greater than KAWETH_FIRMWARE_BUF_SIZE. This removes the leak by calling release_firmware() before we return -ENOSPC. Signed-off-by: Jesper Juhl Signed-off-by: David S. Miller diff --git a/drivers/net/usb/kaweth.c b/drivers/net/usb/kaweth.c index 5e98643..7dc8497 100644 --- a/drivers/net/usb/kaweth.c +++ b/drivers/net/usb/kaweth.c @@ -406,6 +406,7 @@ static int kaweth_download_firmware(struct kaweth_device *kaweth, if (fw->size > KAWETH_FIRMWARE_BUF_SIZE) { err("Firmware too big: %zu", fw->size); + release_firmware(fw); return -ENOSPC; } data_len = fw->size; -- cgit v0.10.2 From de0368d5fec7b9ef95228510f2edb79610beb448 Mon Sep 17 00:00:00 2001 From: Jesper Dangaard Brouer Date: Mon, 24 Jan 2011 02:41:37 +0000 Subject: textsearch: doc - fix spelling in lib/textsearch.c. Found the following spelling errors while reading the textsearch code: "facitilies" -> "facilities" "continously" -> "continuously" "arbitary" -> "arbitrary" "patern" -> "pattern" "occurences" -> "occurrences" I'll try to push this patch through DaveM, given the only users of textsearch is in the net/ tree (nf_conntrack_amanda.c, xt_string.c and em_text.c) Signed-off-by: Jesper Sander Signed-off-by: Jesper Dangaard Brouer Signed-off-by: David S. Miller diff --git a/lib/textsearch.c b/lib/textsearch.c index d608331..e0cc014 100644 --- a/lib/textsearch.c +++ b/lib/textsearch.c @@ -13,7 +13,7 @@ * * INTRODUCTION * - * The textsearch infrastructure provides text searching facitilies for + * The textsearch infrastructure provides text searching facilities for * both linear and non-linear data. Individual search algorithms are * implemented in modules and chosen by the user. * @@ -43,7 +43,7 @@ * to the algorithm to store persistent variables. * (4) Core eventually resets the search offset and forwards the find() * request to the algorithm. - * (5) Algorithm calls get_next_block() provided by the user continously + * (5) Algorithm calls get_next_block() provided by the user continuously * to fetch the data to be searched in block by block. * (6) Algorithm invokes finish() after the last call to get_next_block * to clean up any leftovers from get_next_block. (Optional) @@ -58,15 +58,15 @@ * the pattern to look for and flags. As a flag, you can set TS_IGNORECASE * to perform case insensitive matching. But it might slow down * performance of algorithm, so you should use it at own your risk. - * The returned configuration may then be used for an arbitary + * The returned configuration may then be used for an arbitrary * amount of times and even in parallel as long as a separate struct * ts_state variable is provided to every instance. * * The actual search is performed by either calling textsearch_find_- * continuous() for linear data or by providing an own get_next_block() * implementation and calling textsearch_find(). Both functions return - * the position of the first occurrence of the patern or UINT_MAX if - * no match was found. Subsequent occurences can be found by calling + * the position of the first occurrence of the pattern or UINT_MAX if + * no match was found. Subsequent occurrences can be found by calling * textsearch_next() regardless of the linearity of the data. * * Once you're done using a configuration it must be given back via -- cgit v0.10.2 From 73a8bd74e2618990dbb218c3d82f53e60acd9af0 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Sun, 23 Jan 2011 23:27:15 -0800 Subject: ipv6: Revert 'administrative down' address handling changes. This reverts the following set of commits: d1ed113f1669390da9898da3beddcc058d938587 ("ipv6: remove duplicate neigh_ifdown") 29ba5fed1bbd09c2cba890798c8f9eaab251401d ("ipv6: don't flush routes when setting loopback down") 9d82ca98f71fd686ef2f3017c5e3e6a4871b6e46 ("ipv6: fix missing in6_ifa_put in addrconf") 2de795707294972f6c34bae9de713e502c431296 ("ipv6: addrconf: don't remove address state on ifdown if the address is being kept") 8595805aafc8b077e01804c9a3668e9aa3510e89 ("IPv6: only notify protocols if address is compeletely gone") 27bdb2abcc5edb3526e25407b74bf17d1872c329 ("IPv6: keep tentative addresses in hash table") 93fa159abe50d3c55c7f83622d3f5c09b6e06f4b ("IPv6: keep route for tentative address") 8f37ada5b5f6bfb4d251a7f510f249cb855b77b3 ("IPv6: fix race between cleanup and add/delete address") 84e8b803f1e16f3a2b8b80f80a63fa2f2f8a9be6 ("IPv6: addrconf notify when address is unavailable") dc2b99f71ef477a31020511876ab4403fb7c4420 ("IPv6: keep permanent addresses on admin down") because the core semantic change to ipv6 address handling on ifdown has broken some things, in particular "disable_ipv6" sysctl handling. Stephen has made several attempts to get things back in working order, but nothing has restored disable_ipv6 fully yet. Reported-by: Eric W. Biederman Tested-by: Eric W. Biederman Signed-off-by: David S. Miller diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c index 24a1cf1..fd6782e 100644 --- a/net/ipv6/addrconf.c +++ b/net/ipv6/addrconf.c @@ -2661,14 +2661,12 @@ static int addrconf_ifdown(struct net_device *dev, int how) struct net *net = dev_net(dev); struct inet6_dev *idev; struct inet6_ifaddr *ifa; - LIST_HEAD(keep_list); - int state; + int state, i; ASSERT_RTNL(); - /* Flush routes if device is being removed or it is not loopback */ - if (how || !(dev->flags & IFF_LOOPBACK)) - rt6_ifdown(net, dev); + rt6_ifdown(net, dev); + neigh_ifdown(&nd_tbl, dev); idev = __in6_dev_get(dev); if (idev == NULL) @@ -2689,6 +2687,23 @@ static int addrconf_ifdown(struct net_device *dev, int how) } + /* Step 2: clear hash table */ + for (i = 0; i < IN6_ADDR_HSIZE; i++) { + struct hlist_head *h = &inet6_addr_lst[i]; + struct hlist_node *n; + + spin_lock_bh(&addrconf_hash_lock); + restart: + hlist_for_each_entry_rcu(ifa, n, h, addr_lst) { + if (ifa->idev == idev) { + hlist_del_init_rcu(&ifa->addr_lst); + addrconf_del_timer(ifa); + goto restart; + } + } + spin_unlock_bh(&addrconf_hash_lock); + } + write_lock_bh(&idev->lock); /* Step 2: clear flags for stateless addrconf */ @@ -2722,52 +2737,23 @@ static int addrconf_ifdown(struct net_device *dev, int how) struct inet6_ifaddr, if_list); addrconf_del_timer(ifa); - /* If just doing link down, and address is permanent - and not link-local, then retain it. */ - if (!how && - (ifa->flags&IFA_F_PERMANENT) && - !(ipv6_addr_type(&ifa->addr) & IPV6_ADDR_LINKLOCAL)) { - list_move_tail(&ifa->if_list, &keep_list); - - /* If not doing DAD on this address, just keep it. */ - if ((dev->flags&(IFF_NOARP|IFF_LOOPBACK)) || - idev->cnf.accept_dad <= 0 || - (ifa->flags & IFA_F_NODAD)) - continue; + list_del(&ifa->if_list); - /* If it was tentative already, no need to notify */ - if (ifa->flags & IFA_F_TENTATIVE) - continue; + write_unlock_bh(&idev->lock); - /* Flag it for later restoration when link comes up */ - ifa->flags |= IFA_F_TENTATIVE; - ifa->state = INET6_IFADDR_STATE_DAD; - } else { - list_del(&ifa->if_list); - - /* clear hash table */ - spin_lock_bh(&addrconf_hash_lock); - hlist_del_init_rcu(&ifa->addr_lst); - spin_unlock_bh(&addrconf_hash_lock); - - write_unlock_bh(&idev->lock); - spin_lock_bh(&ifa->state_lock); - state = ifa->state; - ifa->state = INET6_IFADDR_STATE_DEAD; - spin_unlock_bh(&ifa->state_lock); - - if (state != INET6_IFADDR_STATE_DEAD) { - __ipv6_ifa_notify(RTM_DELADDR, ifa); - atomic_notifier_call_chain(&inet6addr_chain, - NETDEV_DOWN, ifa); - } + spin_lock_bh(&ifa->state_lock); + state = ifa->state; + ifa->state = INET6_IFADDR_STATE_DEAD; + spin_unlock_bh(&ifa->state_lock); - in6_ifa_put(ifa); - write_lock_bh(&idev->lock); + if (state != INET6_IFADDR_STATE_DEAD) { + __ipv6_ifa_notify(RTM_DELADDR, ifa); + atomic_notifier_call_chain(&inet6addr_chain, NETDEV_DOWN, ifa); } - } + in6_ifa_put(ifa); - list_splice(&keep_list, &idev->addr_list); + write_lock_bh(&idev->lock); + } write_unlock_bh(&idev->lock); @@ -4156,8 +4142,7 @@ static void __ipv6_ifa_notify(int event, struct inet6_ifaddr *ifp) addrconf_leave_solict(ifp->idev, &ifp->addr); dst_hold(&ifp->rt->dst); - if (ifp->state == INET6_IFADDR_STATE_DEAD && - ip6_del_rt(ifp->rt)) + if (ip6_del_rt(ifp->rt)) dst_free(&ifp->rt->dst); break; } -- cgit v0.10.2 From eb3e554b4b3a56386ef5214dbe0e3935a350178b Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Mon, 24 Jan 2011 19:28:49 +0100 Subject: mac80211: fix a crash in ieee80211_beacon_get_tim on change_interface Some drivers (e.g. ath9k) do not always disable beacons when they're supposed to. When an interface is changed using the change_interface op, the mode specific sdata part is in an undefined state and trying to get a beacon at this point can produce weird crashes. To fix this, add a check for ieee80211_sdata_running before using anything from the sdata. Signed-off-by: Felix Fietkau Cc: stable@kernel.org Signed-off-by: John W. Linville diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c index 5950e3a..b64b42b 100644 --- a/net/mac80211/tx.c +++ b/net/mac80211/tx.c @@ -2230,6 +2230,9 @@ struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, sdata = vif_to_sdata(vif); + if (!ieee80211_sdata_running(sdata)) + goto out; + if (tim_offset) *tim_offset = 0; if (tim_length) -- cgit v0.10.2 From 9c4cf6d94fb362c27a24df5223ed6e327eb7279a Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Tue, 25 Jan 2011 17:42:29 +0800 Subject: rt2x00: add device id for windy31 usb device This patch adds the device id for the windy31 USB device to the rt73usb driver. Thanks to Ralf Flaxa for reporting this and providing testing and a sample device. Reported-by: Ralf Flaxa Tested-by: Ralf Flaxa Cc: stable Signed-off-by: Greg Kroah-Hartman Acked-by: Ivo van Doorn Signed-off-by: John W. Linville diff --git a/drivers/net/wireless/rt2x00/rt73usb.c b/drivers/net/wireless/rt2x00/rt73usb.c index 0b4e859..029be3c 100644 --- a/drivers/net/wireless/rt2x00/rt73usb.c +++ b/drivers/net/wireless/rt2x00/rt73usb.c @@ -2446,6 +2446,7 @@ static struct usb_device_id rt73usb_device_table[] = { { USB_DEVICE(0x04bb, 0x093d), USB_DEVICE_DATA(&rt73usb_ops) }, { USB_DEVICE(0x148f, 0x2573), USB_DEVICE_DATA(&rt73usb_ops) }, { USB_DEVICE(0x148f, 0x2671), USB_DEVICE_DATA(&rt73usb_ops) }, + { USB_DEVICE(0x0812, 0x3101), USB_DEVICE_DATA(&rt73usb_ops) }, /* Qcom */ { USB_DEVICE(0x18e8, 0x6196), USB_DEVICE_DATA(&rt73usb_ops) }, { USB_DEVICE(0x18e8, 0x6229), USB_DEVICE_DATA(&rt73usb_ops) }, -- cgit v0.10.2 From acd9f9cc305ca2e5da2a39f6f6160cd4b476e38b Mon Sep 17 00:00:00 2001 From: Reinette Chatre Date: Tue, 25 Jan 2011 08:38:06 -0800 Subject: MAINTAINERS: remove Reinette Chatre as iwlwifi maintainer Signed-off-by: Reinette Chatre Signed-off-by: Wey-Yi Guy Signed-off-by: John W. Linville diff --git a/MAINTAINERS b/MAINTAINERS index 23d0436..c9ec9d8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3209,7 +3209,6 @@ F: drivers/net/wimax/i2400m/ F: include/linux/wimax/i2400m.h INTEL WIRELESS WIFI LINK (iwlwifi) -M: Reinette Chatre M: Wey-Yi Guy M: Intel Linux Wireless L: linux-wireless@vger.kernel.org -- cgit v0.10.2 From 44f5324b5d13ef2187729d949eca442689627f39 Mon Sep 17 00:00:00 2001 From: Jerry Chu Date: Tue, 25 Jan 2011 13:46:30 -0800 Subject: TCP: fix a bug that triggers large number of TCP RST by mistake This patch fixes a bug that causes TCP RST packets to be generated on otherwise correctly behaved applications, e.g., no unread data on close,..., etc. To trigger the bug, at least two conditions must be met: 1. The FIN flag is set on the last data packet, i.e., it's not on a separate, FIN only packet. 2. The size of the last data chunk on the receive side matches exactly with the size of buffer posted by the receiver, and the receiver closes the socket without any further read attempt. This bug was first noticed on our netperf based testbed for our IW10 proposal to IETF where a large number of RST packets were observed. netperf's read side code meets the condition 2 above 100%. Before the fix, tcp_data_queue() will queue the last skb that meets condition 1 to sk_receive_queue even though it has fully copied out (skb_copy_datagram_iovec()) the data. Then if condition 2 is also met, tcp_recvmsg() often returns all the copied out data successfully without actually consuming the skb, due to a check "if ((chunk = len - tp->ucopy.len) != 0) {" and "len -= chunk;" after tcp_prequeue_process() that causes "len" to become 0 and an early exit from the big while loop. I don't see any reason not to free the skb whose data have been fully consumed in tcp_data_queue(), regardless of the FIN flag. We won't get there if MSG_PEEK is on. Am I missing some arcane cases related to urgent data? Signed-off-by: H.K. Jerry Chu Signed-off-by: David S. Miller diff --git a/net/ipv4/tcp_input.c b/net/ipv4/tcp_input.c index 2549b29..eb7f82e 100644 --- a/net/ipv4/tcp_input.c +++ b/net/ipv4/tcp_input.c @@ -4399,7 +4399,7 @@ static void tcp_data_queue(struct sock *sk, struct sk_buff *skb) if (!skb_copy_datagram_iovec(skb, 0, tp->ucopy.iov, chunk)) { tp->ucopy.len -= chunk; tp->copied_seq += chunk; - eaten = (chunk == skb->len && !th->fin); + eaten = (chunk == skb->len); tcp_rcv_space_adjust(sk); } local_bh_disable(); -- cgit v0.10.2 From de221bd5eb5e754806fcc39c40bb12b96515d9c5 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Nicolas=20de=20Peslo=C3=BCan?= Date: Mon, 24 Jan 2011 13:21:37 +0000 Subject: bonding: update documentation - alternate configuration. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The bonding documentation used to provide configuration details and examples for initscripts and sysconfig only. This patch describe the third possible configuration: /etc/network/interfaces. Signed-off-by: Nicolas de Pesloüan Signed-off-by: David S. Miller diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 5dc6387..25d2f41 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -49,7 +49,8 @@ Table of Contents 3.3 Configuring Bonding Manually with Ifenslave 3.3.1 Configuring Multiple Bonds Manually 3.4 Configuring Bonding Manually via Sysfs -3.5 Overriding Configuration for Special Cases +3.5 Configuration with Interfaces Support +3.6 Overriding Configuration for Special Cases 4. Querying Bonding Configuration 4.1 Bonding Configuration @@ -161,8 +162,8 @@ onwards) do not have /usr/include/linux symbolically linked to the default kernel source include directory. SECOND IMPORTANT NOTE: - If you plan to configure bonding using sysfs, you do not need -to use ifenslave. + If you plan to configure bonding using sysfs or using the +/etc/network/interfaces file, you do not need to use ifenslave. 2. Bonding Driver Options ========================= @@ -779,22 +780,26 @@ resend_igmp You can configure bonding using either your distro's network initialization scripts, or manually using either ifenslave or the -sysfs interface. Distros generally use one of two packages for the -network initialization scripts: initscripts or sysconfig. Recent -versions of these packages have support for bonding, while older +sysfs interface. Distros generally use one of three packages for the +network initialization scripts: initscripts, sysconfig or interfaces. +Recent versions of these packages have support for bonding, while older versions do not. We will first describe the options for configuring bonding for -distros using versions of initscripts and sysconfig with full or -partial support for bonding, then provide information on enabling +distros using versions of initscripts, sysconfig and interfaces with full +or partial support for bonding, then provide information on enabling bonding without support from the network initialization scripts (i.e., older versions of initscripts or sysconfig). - If you're unsure whether your distro uses sysconfig or -initscripts, or don't know if it's new enough, have no fear. + If you're unsure whether your distro uses sysconfig, +initscripts or interfaces, or don't know if it's new enough, have no fear. Determining this is fairly straightforward. - First, issue the command: + First, look for a file called interfaces in /etc/network directory. +If this file is present in your system, then your system use interfaces. See +Configuration with Interfaces Support. + + Else, issue the command: $ rpm -qf /sbin/ifup @@ -1327,8 +1332,62 @@ echo 2000 > /sys/class/net/bond1/bonding/arp_interval echo +eth2 > /sys/class/net/bond1/bonding/slaves echo +eth3 > /sys/class/net/bond1/bonding/slaves -3.5 Overriding Configuration for Special Cases +3.5 Configuration with Interfaces Support +----------------------------------------- + + This section applies to distros which use /etc/network/interfaces file +to describe network interface configuration, most notably Debian and it's +derivatives. + + The ifup and ifdown commands on Debian don't support bonding out of +the box. The ifenslave-2.6 package should be installed to provide bonding +support. Once installed, this package will provide bond-* options to be used +into /etc/network/interfaces. + + Note that ifenslave-2.6 package will load the bonding module and use +the ifenslave command when appropriate. + +Example Configurations +---------------------- + +In /etc/network/interfaces, the following stanza will configure bond0, in +active-backup mode, with eth0 and eth1 as slaves. + +auto bond0 +iface bond0 inet dhcp + bond-slaves eth0 eth1 + bond-mode active-backup + bond-miimon 100 + bond-primary eth0 eth1 + +If the above configuration doesn't work, you might have a system using +upstart for system startup. This is most notably true for recent +Ubuntu versions. The following stanza in /etc/network/interfaces will +produce the same result on those systems. + +auto bond0 +iface bond0 inet dhcp + bond-slaves none + bond-mode active-backup + bond-miimon 100 + +auto eth0 +iface eth0 inet manual + bond-master bond0 + bond-primary eth0 eth1 + +auto eth1 +iface eth1 inet manual + bond-master bond0 + bond-primary eth0 eth1 + +For a full list of bond-* supported options in /etc/network/interfaces and some +more advanced examples tailored to you particular distros, see the files in +/usr/share/doc/ifenslave-2.6. + +3.6 Overriding Configuration for Special Cases ---------------------------------------------- + When using the bonding driver, the physical port which transmits a frame is typically selected by the bonding driver, and is not relevant to the user or system administrator. The output port is simply selected using the policies of -- cgit v0.10.2 From 34c92049ac15dcb731dc455d165b4c3c1df569cf Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Wed, 26 Jan 2011 13:13:10 -0800 Subject: tg3: Use new VLAN code This patch pivots the tg3 driver to the new VLAN infrastructure. All references to vlgrp have been removed. The driver still attempts to disable VLAN tag stripping if CONFIG_VLAN_8021Q or CONFIG_VLAN_8021Q_MODULE is not defined. Signed-off-by: Matt Carlson Reviewed-by: Michael Chan Signed-off-by: David S. Miller diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index 7841a8f..93b32d3 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -60,12 +60,6 @@ #define BAR_0 0 #define BAR_2 2 -#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) -#define TG3_VLAN_TAG_USED 1 -#else -#define TG3_VLAN_TAG_USED 0 -#endif - #include "tg3.h" #define DRV_MODULE_NAME "tg3" @@ -134,9 +128,6 @@ TG3_TX_RING_SIZE) #define NEXT_TX(N) (((N) + 1) & (TG3_TX_RING_SIZE - 1)) -#define TG3_RX_DMA_ALIGN 16 -#define TG3_RX_HEADROOM ALIGN(VLAN_HLEN, TG3_RX_DMA_ALIGN) - #define TG3_DMA_BYTE_ENAB 64 #define TG3_RX_STD_DMA_SZ 1536 @@ -4722,8 +4713,6 @@ static int tg3_rx(struct tg3_napi *tnapi, int budget) struct sk_buff *skb; dma_addr_t dma_addr; u32 opaque_key, desc_idx, *post_ptr; - bool hw_vlan __maybe_unused = false; - u16 vtag __maybe_unused = 0; desc_idx = desc->opaque & RXD_OPAQUE_INDEX_MASK; opaque_key = desc->opaque & RXD_OPAQUE_RING_MASK; @@ -4782,12 +4771,12 @@ static int tg3_rx(struct tg3_napi *tnapi, int budget) tg3_recycle_rx(tnapi, tpr, opaque_key, desc_idx, *post_ptr); - copy_skb = netdev_alloc_skb(tp->dev, len + VLAN_HLEN + + copy_skb = netdev_alloc_skb(tp->dev, len + TG3_RAW_IP_ALIGN); if (copy_skb == NULL) goto drop_it_no_recycle; - skb_reserve(copy_skb, TG3_RAW_IP_ALIGN + VLAN_HLEN); + skb_reserve(copy_skb, TG3_RAW_IP_ALIGN); skb_put(copy_skb, len); pci_dma_sync_single_for_cpu(tp->pdev, dma_addr, len, PCI_DMA_FROMDEVICE); skb_copy_from_linear_data(skb, copy_skb->data, len); @@ -4814,30 +4803,11 @@ static int tg3_rx(struct tg3_napi *tnapi, int budget) } if (desc->type_flags & RXD_FLAG_VLAN && - !(tp->rx_mode & RX_MODE_KEEP_VLAN_TAG)) { - vtag = desc->err_vlan & RXD_VLAN_MASK; -#if TG3_VLAN_TAG_USED - if (tp->vlgrp) - hw_vlan = true; - else -#endif - { - struct vlan_ethhdr *ve = (struct vlan_ethhdr *) - __skb_push(skb, VLAN_HLEN); - - memmove(ve, skb->data + VLAN_HLEN, - ETH_ALEN * 2); - ve->h_vlan_proto = htons(ETH_P_8021Q); - ve->h_vlan_TCI = htons(vtag); - } - } + !(tp->rx_mode & RX_MODE_KEEP_VLAN_TAG)) + __vlan_hwaccel_put_tag(skb, + desc->err_vlan & RXD_VLAN_MASK); -#if TG3_VLAN_TAG_USED - if (hw_vlan) - vlan_gro_receive(&tnapi->napi, tp->vlgrp, vtag, skb); - else -#endif - napi_gro_receive(&tnapi->napi, skb); + napi_gro_receive(&tnapi->napi, skb); received++; budget--; @@ -5740,11 +5710,9 @@ static netdev_tx_t tg3_start_xmit(struct sk_buff *skb, base_flags |= TXD_FLAG_TCPUDP_CSUM; } -#if TG3_VLAN_TAG_USED if (vlan_tx_tag_present(skb)) base_flags |= (TXD_FLAG_VLAN | (vlan_tx_tag_get(skb) << 16)); -#endif len = skb_headlen(skb); @@ -5986,11 +5954,10 @@ static netdev_tx_t tg3_start_xmit_dma_bug(struct sk_buff *skb, } } } -#if TG3_VLAN_TAG_USED + if (vlan_tx_tag_present(skb)) base_flags |= (TXD_FLAG_VLAN | (vlan_tx_tag_get(skb) << 16)); -#endif if ((tp->tg3_flags3 & TG3_FLG3_USE_JUMBO_BDFLAG) && !mss && skb->len > VLAN_ETH_FRAME_LEN) @@ -9532,17 +9499,10 @@ static void __tg3_set_rx_mode(struct net_device *dev) rx_mode = tp->rx_mode & ~(RX_MODE_PROMISC | RX_MODE_KEEP_VLAN_TAG); +#if !defined(CONFIG_VLAN_8021Q) && !defined(CONFIG_VLAN_8021Q_MODULE) /* When ASF is in use, we always keep the RX_MODE_KEEP_VLAN_TAG * flag clear. */ -#if TG3_VLAN_TAG_USED - if (!tp->vlgrp && - !(tp->tg3_flags & TG3_FLAG_ENABLE_ASF)) - rx_mode |= RX_MODE_KEEP_VLAN_TAG; -#else - /* By definition, VLAN is disabled always in this - * case. - */ if (!(tp->tg3_flags & TG3_FLAG_ENABLE_ASF)) rx_mode |= RX_MODE_KEEP_VLAN_TAG; #endif @@ -11230,31 +11190,6 @@ static int tg3_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) return -EOPNOTSUPP; } -#if TG3_VLAN_TAG_USED -static void tg3_vlan_rx_register(struct net_device *dev, struct vlan_group *grp) -{ - struct tg3 *tp = netdev_priv(dev); - - if (!netif_running(dev)) { - tp->vlgrp = grp; - return; - } - - tg3_netif_stop(tp); - - tg3_full_lock(tp, 0); - - tp->vlgrp = grp; - - /* Update RX_MODE_KEEP_VLAN_TAG bit in RX_MODE register. */ - __tg3_set_rx_mode(dev); - - tg3_netif_start(tp); - - tg3_full_unlock(tp); -} -#endif - static int tg3_get_coalesce(struct net_device *dev, struct ethtool_coalesce *ec) { struct tg3 *tp = netdev_priv(dev); @@ -13066,9 +13001,7 @@ static struct pci_dev * __devinit tg3_find_peer(struct tg3 *); static void inline vlan_features_add(struct net_device *dev, unsigned long flags) { -#if TG3_VLAN_TAG_USED dev->vlan_features |= flags; -#endif } static inline u32 tg3_rx_ret_ring_size(struct tg3 *tp) @@ -13861,11 +13794,11 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) else tp->tg3_flags &= ~TG3_FLAG_POLL_SERDES; - tp->rx_offset = NET_IP_ALIGN + TG3_RX_HEADROOM; + tp->rx_offset = NET_IP_ALIGN; tp->rx_copy_thresh = TG3_RX_COPY_THRESHOLD; if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701 && (tp->tg3_flags & TG3_FLAG_PCIX_MODE) != 0) { - tp->rx_offset -= NET_IP_ALIGN; + tp->rx_offset = 0; #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS tp->rx_copy_thresh = ~(u16)0; #endif @@ -14629,9 +14562,6 @@ static const struct net_device_ops tg3_netdev_ops = { .ndo_do_ioctl = tg3_ioctl, .ndo_tx_timeout = tg3_tx_timeout, .ndo_change_mtu = tg3_change_mtu, -#if TG3_VLAN_TAG_USED - .ndo_vlan_rx_register = tg3_vlan_rx_register, -#endif #ifdef CONFIG_NET_POLL_CONTROLLER .ndo_poll_controller = tg3_poll_controller, #endif @@ -14648,9 +14578,6 @@ static const struct net_device_ops tg3_netdev_ops_dma_bug = { .ndo_do_ioctl = tg3_ioctl, .ndo_tx_timeout = tg3_tx_timeout, .ndo_change_mtu = tg3_change_mtu, -#if TG3_VLAN_TAG_USED - .ndo_vlan_rx_register = tg3_vlan_rx_register, -#endif #ifdef CONFIG_NET_POLL_CONTROLLER .ndo_poll_controller = tg3_poll_controller, #endif @@ -14700,9 +14627,7 @@ static int __devinit tg3_init_one(struct pci_dev *pdev, SET_NETDEV_DEV(dev, &pdev->dev); -#if TG3_VLAN_TAG_USED dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; -#endif tp = netdev_priv(dev); tp->pdev = pdev; diff --git a/drivers/net/tg3.h b/drivers/net/tg3.h index d62c8d9..f528243 100644 --- a/drivers/net/tg3.h +++ b/drivers/net/tg3.h @@ -2808,9 +2808,6 @@ struct tg3 { u32 rx_std_max_post; u32 rx_offset; u32 rx_pkt_map_sz; -#if TG3_VLAN_TAG_USED - struct vlan_group *vlgrp; -#endif /* begin "everything else" cacheline(s) section */ -- cgit v0.10.2 From 7cc2edb83447775a34ed3bf9d29d8295a434b523 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Wed, 26 Jan 2011 13:41:03 -0800 Subject: xfrm6: Don't forget to propagate peer into ipsec route. Like ipv4, we have to propagate the ipv6 route peer into the ipsec top-level route during instantiation. Signed-off-by: David S. Miller diff --git a/net/ipv6/xfrm6_policy.c b/net/ipv6/xfrm6_policy.c index 7e74023..da87428 100644 --- a/net/ipv6/xfrm6_policy.c +++ b/net/ipv6/xfrm6_policy.c @@ -98,6 +98,10 @@ static int xfrm6_fill_dst(struct xfrm_dst *xdst, struct net_device *dev, if (!xdst->u.rt6.rt6i_idev) return -ENODEV; + xdst->u.rt6.rt6i_peer = rt->rt6i_peer; + if (rt->rt6i_peer) + atomic_inc(&rt->rt6i_peer->refcnt); + /* Sheit... I remember I did this right. Apparently, * it was magically lost, so this code needs audit */ xdst->u.rt6.rt6i_flags = rt->rt6i_flags & (RTF_ANYCAST | @@ -216,6 +220,8 @@ static void xfrm6_dst_destroy(struct dst_entry *dst) if (likely(xdst->u.rt6.rt6i_idev)) in6_dev_put(xdst->u.rt6.rt6i_idev); + if (likely(xdst->u.rt6.rt6i_peer)) + inet_putpeer(xdst->u.rt6.rt6i_peer); xfrm_dst_destroy(xdst); } -- cgit v0.10.2