From 148cbb53ace32f584d208764c7f7e6aa8edb970c Mon Sep 17 00:00:00 2001
From: Boris BREZILLON <b.brezillon@overkiz.com>
Date: Thu, 22 Aug 2013 17:57:28 +0200
Subject: net/cadence/macb: add support for dt phy definition

The macb driver only handle PHY description through platform_data
(macb_platform_data).
Thus, when using dt you cannot define phy properties like phy address or
phy irq pin.

This patch makes use of the of_mdiobus_register to add support for
phy device definition using dt.
A fallback to the autoscan procedure is added in case there is no phy
devices defined in dt.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c
index e866608..fe06ab0 100644
--- a/drivers/net/ethernet/cadence/macb.c
+++ b/drivers/net/ethernet/cadence/macb.c
@@ -27,6 +27,7 @@
 #include <linux/phy.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/pinctrl/consumer.h>
 
@@ -314,6 +315,7 @@ static int macb_mii_probe(struct net_device *dev)
 int macb_mii_init(struct macb *bp)
 {
 	struct macb_platform_data *pdata;
+	struct device_node *np;
 	int err = -ENXIO, i;
 
 	/* Enable management port */
@@ -335,21 +337,46 @@ int macb_mii_init(struct macb *bp)
 	bp->mii_bus->parent = &bp->dev->dev;
 	pdata = bp->pdev->dev.platform_data;
 
-	if (pdata)
-		bp->mii_bus->phy_mask = pdata->phy_mask;
-
 	bp->mii_bus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
 	if (!bp->mii_bus->irq) {
 		err = -ENOMEM;
 		goto err_out_free_mdiobus;
 	}
 
-	for (i = 0; i < PHY_MAX_ADDR; i++)
-		bp->mii_bus->irq[i] = PHY_POLL;
-
 	dev_set_drvdata(&bp->dev->dev, bp->mii_bus);
 
-	if (mdiobus_register(bp->mii_bus))
+	np = bp->pdev->dev.of_node;
+	if (np) {
+		/* try dt phy registration */
+		err = of_mdiobus_register(bp->mii_bus, np);
+
+		/* fallback to standard phy registration if no phy were
+		   found during dt phy registration */
+		if (!err && !phy_find_first(bp->mii_bus)) {
+			for (i = 0; i < PHY_MAX_ADDR; i++) {
+				struct phy_device *phydev;
+
+				phydev = mdiobus_scan(bp->mii_bus, i);
+				if (IS_ERR(phydev)) {
+					err = PTR_ERR(phydev);
+					break;
+				}
+			}
+
+			if (err)
+				goto err_out_unregister_bus;
+		}
+	} else {
+		for (i = 0; i < PHY_MAX_ADDR; i++)
+			bp->mii_bus->irq[i] = PHY_POLL;
+
+		if (pdata)
+			bp->mii_bus->phy_mask = pdata->phy_mask;
+
+		err = mdiobus_register(bp->mii_bus);
+	}
+
+	if (err)
 		goto err_out_free_mdio_irq;
 
 	if (macb_mii_probe(bp->dev) != 0) {
-- 
cgit v0.10.2


From 8c038e7e14b1c5f156745e3c4df0a3aa46173dd9 Mon Sep 17 00:00:00 2001
From: Boris BREZILLON <b.brezillon@overkiz.com>
Date: Thu, 22 Aug 2013 17:58:29 +0200
Subject: ARM: at91/dt: define phy available on sama5d3 mother board

This patch describe the phy used on atmel sama5d3 mother board:
 - phy address
 - phy interrupt pin

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi
index 8a9e05d..e9521d5 100644
--- a/arch/arm/boot/dts/sama5d3xmb.dtsi
+++ b/arch/arm/boot/dts/sama5d3xmb.dtsi
@@ -81,6 +81,14 @@
 
 			macb1: ethernet@f802c000 {
 				phy-mode = "rmii";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+				phy0: ethernet-phy@0 {
+					interrupt-parent = <&pioE>;
+					interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+					reg = <1>;
+				};
 			};
 
 			pinctrl@fffff200 {
-- 
cgit v0.10.2