diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt')
-rw-r--r-- | Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt | 65 |
1 files changed, 65 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt new file mode 100644 index 0000000..377afbf --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -0,0 +1,65 @@ +Device-Tree bindings for Samsung Exynos SoC display controller (DECON) + +DECON (Display and Enhancement Controller) is the Display Controller for the +Exynos series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be "samsung,exynos5433-decon"; +- reg: physical base address and length of the DECON registers set. +- interrupts: should contain a list of all DECON IP block interrupts in the + order: VSYNC, LCD_SYSTEM. The interrupt specifier format + depends on the interrupt controller used. +- interrupt-names: should contain the interrupt names: "vsync", "lcd_sys" + in the same order as they were listed in the interrupts + property. +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. +- clock-names: list of clock names sorted in the same order as the clocks + property. Must contain "aclk_decon", "aclk_smmu_decon0x", + "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", + "sclk_decon_eclk" +- ports: contains a port which is connected to mic node. address-cells and + size-cells must 1 and 0, respectively. +- port: contains an endpoint node which is connected to the endpoint in the mic + node. The reg value muset be 0. +- i80-if-timings: specify whether the panel which is connected to decon uses + i80 lcd interface or mipi video interface. This node contains + no timing information as that of fimd does. Because there is + no register in decon to specify i80 interface timing value, + it is not needed, but make it remain to use same kind of node + in fimd and exynos7 decon. + +Example: +SoC specific DT entry: +decon: decon@13800000 { + compatible = "samsung,exynos5433-decon"; + reg = <0x13800000 0x2104>; + clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>, + <&cmu_disp CLK_ACLK_XIU_DECON0X>, + <&cmu_disp CLK_PCLK_SMMU_DECON0X>, + <&cmu_disp CLK_SCLK_DECON_VCLK>, + <&cmu_disp CLK_SCLK_DECON_ECLK>; + clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", + "pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk"; + interrupt-names = "vsync", "lcd_sys"; + interrupts = <0 202 0>, <0 203 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + decon_to_mic: endpoint { + remote-endpoint = <&mic_to_decon>; + }; + }; + }; +}; + +Board specific DT entry: +&decon { + i80-if-timings { + }; +}; |