Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire regression fix from Stefan Richter:
"IEEE 1394 (FireWire) subsystem fix: MSI don't work on VIA PCIe
controllers with some isochronous workloads (regression since
v3.16-rc1)"
* tag 'firewire-fix-vt6315' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: disable MSI for VIA VT6315 again
|
|
Revert half of commit d151f9854f21: If isochronous I/O is attempted with
packets larget than 1 kByte, VIA VT6315 rev 01 immediately stops to generate
any interrupts if MSI are used. Fix this by going back to legacy interrupts.
[Thread "Isochronous streaming with VT6315 OHCI",
http://marc.info/?t=139049641500003]
With smaller packets, the loss of IRQs happens too but only very rarely ---
rarely eneough that it was not yet possible for me to determine whether
QUIRK_NO_MSI is an actual fix for this rare variation of this chip bug.
I am keeping QUIRK_CYCLE_TIMER off of VT6315 rev >= 1 because this has been
verified by myself with certainty. On the other hand, I am also keeping
QUIRK_CYCLE_TIMER on for VT6315 rev 0 because I don't know at this time
whether this revision accesses Cycle Timer non-atomically like most of the
other VIA OHCIs are known to do.
Reported-by: Rémy Bruno <remy-fw@remy.trinnov.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394 into next
Pull firewire updates from Stefan Richter:
"IEEE 1394 (FireWire) subsystem changes: One optimization for some VIA
controllers, one fix, one kconfig brushup"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: enable MSI for VIA VT6315 rev 1, drop cycle timer quirk
firewire: Use COMPILE_TEST for build testing
firewire: net: fix NULL derefencing in fwnet_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle were:
- reduced/streamlined smp_mb__*() interface that allows more usecases
and makes the existing ones less buggy, especially in rarer
architectures
- add rwsem implementation comments
- bump up lockdep limits"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
rwsem: Add comments to explain the meaning of the rwsem's count field
lockdep: Increase static allocations
arch: Mass conversion of smp_mb__*()
arch,doc: Convert smp_mb__*()
arch,xtensa: Convert smp_mb__*()
arch,x86: Convert smp_mb__*()
arch,tile: Convert smp_mb__*()
arch,sparc: Convert smp_mb__*()
arch,sh: Convert smp_mb__*()
arch,score: Convert smp_mb__*()
arch,s390: Convert smp_mb__*()
arch,powerpc: Convert smp_mb__*()
arch,parisc: Convert smp_mb__*()
arch,openrisc: Convert smp_mb__*()
arch,mn10300: Convert smp_mb__*()
arch,mips: Convert smp_mb__*()
arch,metag: Convert smp_mb__*()
arch,m68k: Convert smp_mb__*()
arch,m32r: Convert smp_mb__*()
arch,ia64: Convert smp_mb__*()
...
|
|
Commit af0cdf494781 "firewire: ohci: fix regression with VIA VT6315,
disable MSI" acted upon a report against VT6315 rev 0:
http://linux.derkeiler.com/Mailing-Lists/Kernel/2010-12/msg02301.html
$ lspci -nn
VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403]
I now got a card with
$ lspci -nn
VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403] (rev 01)
and this works fine with MSI enabled.
Second, I tested this VT6315 rev 1 without CYCLE_TIMER quirk flag using
http://me.in-berlin.de/~s5r6/linux1394/utils/test_cycle_time_v20100125.c
and found that this chip does in fact access the cycle timer atomically.
Things I can't test because I don't have the hardware:
- whether VT6315 rev 0 really needs QUIRK_CYCLE_TIMER,
- whether the VT6320 PCI device needs QUIRK_CYCLE_TIMER,
- whether the VT6325 and VT6330 PCIe devices need QUIRK_CYCLE_TIMER
and QUIRK_NO_MSI.
Hence, just add a whitelist entry specifically for VT6315 rev >= 1
without any quirk flags. Before this entry we need an extra entry to
catch VT6315 rev <= 0 due to how our ID matching logic works.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Undo a feature introduced in v3.14 by commit fcd46b34425d
"firewire: Enable remote DMA above 4 GB". That change raised the
minimum address at which protocol drivers and user programs can register
for request reception from 0x0001'0000'0000 to 0x8000'0000'0000.
It turned out that at least one vendor-specific protocol exists which
uses lower addresses: https://bugzilla.kernel.org/show_bug.cgi?id=76921
For the time being, revert most of commit fcd46b34425d so that affected
protocols work like with kernel v3.13 and before. Just keep the valid
documentation parts from the regressing commit, and the ability to
identify controllers which could be programmed to accept >32 bit
physical DMA addresses. The rest of fcd46b34425d should probably be
brought back as an optional instead of default feature.
Reported-by: Fabien Spindler <fabien.spindler@inria.fr>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Mostly scripted conversion of the smp_mb__* barriers.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-55dhyhocezdw1dg7u19hmh1u@git.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since commit bd972688eb24
"firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8",
there is a high chance that firewire-ohci fails to initialize LSI née
Agere controllers.
https://bugzilla.kernel.org/show_bug.cgi?id=65151
Peter Hurley points out the reason: IEEE 1394a:2000 clause 5A.1 (or
IEEE 1394:2008 clause 17.2.1) say: "The PHY shall insure that no more
than 10 ms elapse from the reassertion of LPS until the interface is
reset. The link shall not assert LReq until the reset is complete."
In other words, the link needs to give the PHY at least 10 ms to get
the interface operational.
With just the msleep(1) in bd972688eb24, the first read_phy_reg()
during ohci_enable() may happen before the phy-link interface reset was
finished, and fail. Due to the high variability of msleep(n) with small
n, this failure was not fully reproducible, and not apparent at all with
low CONFIG_HZ setting.
On the other hand, Peter can no longer reproduce the issue with FW643
rev8. The read phy reg failures that happened back then may have had an
unrelated cause. So, just revert bd972688eb24, except for the valid
comment on TSB82AA2 cards.
Reported-by: Mikhail Gavrilov
Reported-by: Jay Fenlason <fenlason@redhat.com>
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This makes all of a machine's memory accessible to remote debugging via
FireWire, using the physical response unit (i.e. RDMA) of OHCI-1394 link
layer controllers.
This requires actual support by the controller. The only ones currently
known to support it are Agere/LSI FW643. Most if not all other OHCI-1394
controllers do not implement the optional Physical Upper Bound register.
With them, RDMA will continue to be limited to the lowermost 4 GB.
firewire-ohci's startup message in the kernel log is augmented to tell
whether the controller does expose more than 4 GB to RDMA.
While OHCI-1394 allows for a maximum Physical Upper Bound of
0xffff'0000'0000 (near 256 TB), this implementation sets it to
0x8000'0000'0000 (128 TB) in order to avoid interference with applications
that require interrupt-served asynchronous request reception at
respectively low addresses.
Note, this change does not switch remote DMA on. It only increases the
range of remote access to all memory (instead of just 4 GB) whenever
remote DMA was switched on by other means. The latter is achieved by
setting firewire-ohci's remote_dma parameter, or if the physical DMA
filter is opened through firewire-sbp2.
Derived from patch "firewire: Enable physical DMA above 4GB" by
Peter Hurley <peter@hurleysoftware.com> from March 27, 2013.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This makes it possible to debug kernel over FireWire without the need to
recompile it.
[Stefan R: changed description from "...0" to "...N"]
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Put bus_reset_work into its own workqueue. By doing this, forward
progress of bus_reset_work() is guaranteed if the work is switched over
to a rescuer thread.
Switching work to a rescuer thread happens if a new worker thread could
not be allocated in certain time (MAYDAY_INITIAL_TIMEOUT, typically 10
ms). This might not be possible under high memory pressure or even on a
heavily loaded embedded system running a slow serial console.
The former deadlock occured in the following situation:
The rescuer thread ran
fw_device_init->read_config_rom->read_rom->fw_run_transaction.
fw_run_transaction blocked waiting for the completion object.
This completion object would have been completed in bus_reset_work,
but this work was never executed in the rescuer thread due to its
strictly sequential behaviour.
[Stefan R.: Removed WQ_NON_REENTRANT flag from allocation because
it is no longer needed in current kernels. Add it back if you backport
to kernels older than 3.7, i.e. one which does not contain dbf2576e37da
"workqueue: make all workqueues non-reentrant". Swapped order of
destroy_workqueue and pci_unregister_driver.]
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This is a prerequisite to allocate a per driver self_id workqueue.
This reverts the ohci.c part of patch
fe2af11c220c7bb3a67f7aec0594811e5c59e019.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
a) Sort device IDs by vendor -- device -- revision.
b) Write quirk flags in hexadecimal. This affects the user-visible
output of "modinfo firewire-ohci". Since more flags have been added
recently, it is now easier to cope with them in hexadecimal represen-
tation. Besides, the device-specific combination of quirk flags is
shown in hexadecimal in the kernel log too. (And firewire-sbp2
presents its own quirk flags in modinfo as hexadecimals as well.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
We have got
struct descriptor *descriptors;
dma_addr_t descriptors_bus;
dma_addr_t buffer_bus;
struct descriptor buffer[0];
void *misc_buffer;
dma_addr_t misc_buffer_bus;
__be32 *config_rom;
dma_addr_t config_rom_bus;
__be32 *next_config_rom;
dma_addr_t next_config_rom_bus;
But then we have got
__le32 *self_id_cpu;
dma_addr_t self_id_bus;
Better apply the pattern of xyz vs. xyz_bus to self_id vs. self_id_bus
as well. The _cpu suffix looks particularly weird in conversions from
little endian to CPU endian.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Commit 18d627113b83 (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com>
Tested-by: Josep Bosch <jep250@gmail.com>
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
A stack trace is an invaluable tool in determining the basis
and cause of PHY regs read/write failures.
Include PHY reg addr (and value for writes) in the diagnostic.
[Stefan R: changed whitespace]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Many of the error messages possible from bus_reset_work() do not
contain enough information to distinguish which error condition
occurred nor enough information to evaluate the error afterwards.
Differentiate all error conditions in bus_reset_work(); add
additional information to make error diagnosis possible.
[Stefan R: fixed self-ID endian conversion]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Convert dev_xxxx(ohci->card.device, ...) log functions to
ohci_xxxx(ohci, ...).
[Stefan R: Peter argues that this increases readability of the code.]
[Stefan R: changed whitespace]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
With the LSI FW643 rev 8 [1], the first commanded bus reset at
the conclusion of ohci_enable() has been observed to fail with
the following messages:
[ 4.884015] firewire_ohci 0000:01:00.0: failed to read phy reg
....
[ 5.684012] firewire_ohci 0000:01:00.0: failed to read phy reg
With drivers/firewire/ohci.c instrumented, the error condition [2]
indicates the PHY arbitration state machine has timed out prior to
enabling PHY LCtrl.
Furthermore, instrumenting ohci_enable() shows that LPS has been
enabled within 1 ms.
Test LPS latching every 1 ms rather than every 50ms.
[1] lspci -v
01:00.0 FireWire (IEEE 1394): LSI Corporation FW643 [TrueFire] PCIe 1394b Controller (rev 08) (prog-if 10 [OHCI])
Subsystem: LSI Corporation FW643 [TrueFire] PCIe 1394b Controller
Flags: bus master, fast devsel, latency 0, IRQ 92
Memory at fbeff000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 3
Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [60] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [170] Device Serial Number 08-14-43-82-00-00-41-fc
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
[2] instrumented WARNING in read_phy_reg()
[ 4.576010] ------------[ cut here ]------------
[ 4.576035] WARNING: at ./drivers/firewire/ohci.c:570 read_phy_reg+0x93/0xe0 [firewire_ohci]()
[ 4.576050] Hardware name: Precision WorkStation T5400
[ 4.576058] failed to read phy reg:1 (phy(5) @ config enhance:19)
[ 4.576068] Modules linked in: hid_logitech_dj hid_generic(+) usbhid <...snip...>
[ 4.576140] Pid: 61, comm: kworker/2:1 Not tainted 3.8.0-2+fwtest-xeon #2+fwtest
[ 4.576149] Call Trace:
[ 4.576160] [<ffffffff8105468f>] warn_slowpath_common+0x7f/0xc0
[ 4.576168] [<ffffffff81054786>] warn_slowpath_fmt+0x46/0x50
[ 4.576178] [<ffffffffa00caca3>] read_phy_reg+0x93/0xe0 [firewire_ohci]
[ 4.576188] [<ffffffffa00cae19>] ohci_read_phy_reg+0x39/0x60 [firewire_ohci]
[ 4.576203] [<ffffffffa00731ff>] fw_send_phy_config+0xbf/0xe0 [firewire_core]
[ 4.576214] [<ffffffffa006b2d6>] br_work+0x46/0xb0 [firewire_core]
[ 4.576225] [<ffffffff81071e0c>] process_one_work+0x13c/0x500
[ 4.576238] [<ffffffffa006b290>] ? fw_card_initialize+0x180/0x180 [firewire_core]
[ 4.576248] [<ffffffff810737ed>] worker_thread+0x16d/0x470
[ 4.576257] [<ffffffff81073680>] ? busy_worker_rebind_fn+0x100/0x100
[ 4.576266] [<ffffffff8107d160>] kthread+0xc0/0xd0
[ 4.576275] [<ffffffff816a0000>] ? pcpu_dump_alloc_info+0x1cb/0x2c4
[ 4.576284] [<ffffffff8107d0a0>] ? kthread_create_on_node+0x130/0x130
[ 4.576297] [<ffffffff816b2f6c>] ret_from_fork+0x7c/0xb0
[ 4.576305] [<ffffffff8107d0a0>] ? kthread_create_on_node+0x130/0x130
[ 4.576313] ---[ end trace cbc940994b300302 ]---
[Stefan R: Peter also reports a change of behavior with LSI FW323.
Before the patch, there would often occur a lock transaction failure
during firewire-core startup:
[ 6.056022] firewire_core 0000:07:06.0: BM lock failed (timeout), making local node (ffc0) root
This failure no longer happens after the patch, without an obvious
reason for the failure or the fix.]
[Stefan R: Added quirk flag, quirk table entry, and comment.]
Reported-by: Tim Jordan <tim@insipid.org.uk>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Add quirk for VT6306 wake bit behavior.
VT6306 seems to reread the wrong descriptor when the wake bit is
written. work around by putting a copy of the branch address in the
first descriptor of the block.
[Stefan R: This fixes the known broken video reception via gstreamer
on VIA VT6306. 100% repeatable testcase:
$ gst-launch-0.10 dv1394src \! dvdemux \! dvdec \! xvimagesink
with a camcorder or other DV source connected. Likewise for MPEG2-TS
reception via gstreamer, e.g. from TV settop boxes.
Perhaps this also fixes dv4l on VT6306, but this is as yet untested.
Kino, dvgrab or FFADO had not been affected by this chip quirk.
Additional comments from Andy:]
I've looked into some problems with the wake bit on a vt6306 family
chip (1106:3044, rev 46).
I used this firewire card in a mythtv setup (ISO receive MPEG2 stream)
with Debian 2.6.32 kernels for ~2 years without problems.
Since upgrading to 3.2, I've been having problems with the input stream
freezing -- input data stops until I restart mythtv (I expect closing
and reopening the device would be sufficient). This happens
infrequently, maybe one out of 20 recordings. I eventually determined
that the problem is more likely to occur if the system is loaded.
I isolated the kernel version as the triggering SW factor and then
specifically the change from dualbuffer back to packet-per-buffer DMA
mode.
The possibility that the controller does not properly respond to the
wake bit was suggested in
https://bugzilla.redhat.com/show_bug.cgi?id=415841, but not proven.
Based on the fact that dualbuffer mode worked while packet-per-buffer
has trouble, I guessed that upon seeing the wake bit written, the vt6306
controller only checks the branch address in the first descriptor of the
block, even if that is not the correct place to look (because the block
has multiple descriptors).
This theory seems to be correct. When the ISO reception is hung, I am
able to resume it by manually writing the branch address to the first
descriptor in the block, and then writing the wake bit.
I've had luck so far with the attached patch, so I'm including it. It's
probably not a complete solution -- I haven't tested transmit modes to
see whether they have a similar issue.
I doubt that the quirk test is any cheaper than just writing the extra
branch address in all cases, but it does reduce the risk of breaking
other hardware.
[Stefan R: omitted QUIRK_NO_MSI from VT6306 quirks table entry,
changed whitespace]
Signed-off-by: Andy Leiserson <andy@leiserson.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
A pci device can be removed while in its suspended state. If the ohci
host controller is suspended, the PHY is also in low-power mode and
LPS is disabled. If LPS is disabled, most of the host registers aren't
accessible, including IntMaskClear. Furthermore, access to these registers
when LPS is disabled can cause hard lockups on some hardware. Since
interrupts are already disabled in this mode, further action is
unnecessary.
Test LPS before attempting to write IntMaskClear to disable interrupts.
[Stefan R: whitespace changes]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
A pci device can be removed while in its suspended state.
Because the ohci driver freed the irq to suspend, free_irq() is
called twice; once from pci_remove() and again from pci_suspend(),
which issues the warning below [1].
Rather than allocate the irq in the .enable() path, move the
allocation to .probe(). Consequently, the irq is not reallocated
upon pci_resume() and thus is not freed upon pci_suspend().
[1] Warning reported by Mark Einon <mark.einon@gmail.com> when
suspending an MSI MS-1727 GT740 laptop on Ubuntu 3.5.0-22-generic
WARNING: at ./kernel/irq/manage.c:1198 __free_irq+0xa3/0x1e0()
Hardware name: MS-1727
Trying to free already-free IRQ 16
Modules linked in: ip6table_filter ip6_tables ebtable_nat ebtables <...snip...>
Pid: 4, comm: kworker/0:0 Tainted: P O 3.5.0-22-generic #34-Ubuntu
Call Trace:
[<ffffffff81051c1f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff81051d16>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8103fa39>] ? default_spin_lock_flags+0x9/0x10
[<ffffffff810df6b3>] __free_irq+0xa3/0x1e0
[<ffffffff810df844>] free_irq+0x54/0xc0
[<ffffffffa005a27e>] pci_remove+0x6e/0x210 [firewire_ohci]
[<ffffffff8135ae7f>] pci_device_remove+0x3f/0x110
[<ffffffff8141fdbc>] __device_release_driver+0x7c/0xe0
[<ffffffff8141fe4c>] device_release_driver+0x2c/0x40
[<ffffffff8141f5f1>] bus_remove_device+0xe1/0x120
[<ffffffff8141cd1a>] device_del+0x12a/0x1c0
[<ffffffff8141cdc6>] device_unregister+0x16/0x30
[<ffffffff81354784>] pci_stop_bus_device+0x94/0xa0
[<ffffffffa0091c67>] acpiphp_disable_slot+0xb7/0x1a0 [acpiphp]
[<ffffffffa0090716>] ? get_slot_status+0x46/0xc0 [acpiphp]
[<ffffffffa0091d7d>] acpiphp_check_bridge.isra.15+0x2d/0xf0 [acpiphp]
[<ffffffffa0092442>] _handle_hotplug_event_bridge+0x372/0x4d0 [acpiphp]
[<ffffffff81390f8c>] ? acpi_os_execute_deferred+0x2f/0x34
[<ffffffff8116e22d>] ? kfree+0xed/0x110
[<ffffffff8107086a>] process_one_work+0x12a/0x420
[<ffffffffa00920d0>] ? _handle_hotplug_event_func+0x1d0/0x1d0 [acpiphp]
[<ffffffff8107141e>] worker_thread+0x12e/0x2f0
[<ffffffff810712f0>] ? manage_workers.isra.26+0x200/0x200
[<ffffffff81075f13>] kthread+0x93/0xa0
[<ffffffff8168d024>] kernel_thread_helper+0x4/0x10
[<ffffffff81075e80>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff8168d020>] ? gs_change+0x13/0x13
Reported-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
These are redundant to log messages from the mm core.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The old IEEE 1394 driver stack was removed in v2.6.37. That made the
checks for two Kconfig (module) macros unneeded, since they will now
always evaluate to true. Remove these two checks.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Conflicts:
drivers/devfreq/exynos4_bus.c
Sync with Linus' tree to be able to apply patches that are
against newer code (mvneta).
|
|
Correct spelling typo in printk within various drivers.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"Asynchronous" is misspelled in some comments. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In case of a self constructed selfID packet this patch correctly
determines the information if the TSB41BA3D phy initiated a bus reset.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
OHCI 1.1 says:
| Since the value of this bit is undefined after reset in all IR
| contexts, software shall initialize this bit to zero in all contexts
| whether or not active to maintain the exclusive nature of this bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
pci_request_region() does not fail on resources that have not been
allocated by the BIOS or by the kernel, so to avoid accessing
registers that are not there, we have to check for this explicitly.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The Bus_Time CSR is virtually never used, so we can avoid burning CPU in
interrupt context for 1 or 3 IsochronousCycleTimer accesses every minute
by not tracking the bus time until the CSR is actually accessed for the
first time.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
bus_reset_work() is only called from workqueue thread context.
ohci_set_config_rom() and ohci_allocate_iso_context() perform GFP_KERNEL
memory allocations, therefore they must be called with interrupts
enabled.
Hence these functions may disable and enable local IRQs without having
to track IRQ state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
bus_reset_work's reg is a bitfield.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This patch converts the drivers in drivers/firewire/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates post v3.3 from Stefan Richter:
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too. Clemens Ladisch is aware of it.
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394: (26 commits)
firewire: allow explicit flushing of iso packet completions
firewire: prevent dropping of completed iso packet header data
firewire: ohci: factor out iso completion flushing code
firewire: ohci: simplify iso header pointer arithmetic
firewire: ohci: optimize control bit checks
firewire: ohci: remove unused excess_bytes field
firewire: ohci: copy_iso_headers(): make comment match the code
firewire: cdev: fix IR multichannel event documentation
firewire: ohci: fix too-early completion of IR multichannel buffers
firewire: ohci: move runtime debug facility out of #ifdef
firewire: tone down some diagnostic log messages
firewire: sbp2: replace a GFP_ATOMIC allocation
firewire: sbp2: Fix SCSI sense data mangling
firewire: sbp2: Ignore SBP-2 targets on the local node
firewire: sbp2: Take into account Unit_Unique_ID
firewire: nosy: Use the macro DMA_BIT_MASK().
firewire: core: convert AR-req handler lock from _irqsave to _bh
firewire: core: fix race at address_handler unregistration
firewire: core: remove obsolete comment
firewire: core: prefix log messages with card name
...
|
|
Extend the kernel and userspace APIs to allow reporting all currently
completed isochronous packets, even if the next interrupt packet has not
yet been reached. This is required to determine the status of the
packets at the end of a paused or stopped stream, and useful for more
precise synchronization of audio streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The buffer for the header data of completed iso packets has a fixed
size, so it is possible to configure a stream with a big interval
between interrupt packets or with big headers so that this buffer would
overflow. Previously, ohci.c would drop any data that would not fit,
but this could make unsuspecting applications believe that fewer than
the actual number of packets have completed.
Instead of dropping data, add calls to flush_iso_completion() so that
there are as many events as needed to report all of the data.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
In preparation for the following patches that add more flushing, move
the code for flushing accumulated header data into a common function.
The timestamp of the last completed packed is passed through the context
structure instead of a function parameter to allow accessing this value
later outside of the handle_i?_packet functions.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
When storing the header data of completed iso packets, we effectively
treat the buffers as arrays of quadlets. Actually declaring the
pointers as u32* avoids repetitive pointer arithmetic, removes the
unhelpfully named "i" variables, and thus makes the code clearer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Doing the endian conversion on the constant instead of the memory
field allows the compiler to do the conversion at compile time.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Commit 6498ba04aee6 (remove unused dualbuffer IR code) overlooked
a field in struct iso_context.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The comment incorrectly talked about one little-endian quadlet, while
there are actually two. Furthermore, the endianness of the remaining
headers depends on whatever protocol is used, so don't mention them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
handle_ir_buffer_fill() assumed that a completed descriptor would be
indicated by a non-zero transfer_status (as in most other descriptors).
However, this field is written by the controller as soon as (the end of)
the first packet has been written into the buffer. As a consequence, if
we happen to run into such a descriptor when the interrupt handler is
executed after such a packet has completed, the descriptor would be
taken out of the list of active descriptors as soon as the buffer had
been partially filled, so the event for the buffer being completely
filled would never be sent.
To fix this, handle descriptors only when they have been completely
filled, i.e., when res_count == 0. (This also matches the condition
that is reported by the controller with an interrupt.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
CONFIG_FIREWIRE_OHCI_DEBUG could have been exposed to kernel tweakers
if CONFIG_EXPERT was set. But in hindsight, this stuff is far too
useful to omit it. So get rid of two #else branches that are only
going to bitrot otherwise.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The "skipped bus generations" message was added together with the
respective fw_device retaining/ reviving code in order to see how it all
works out. It did well, so don't spam the log anymore.
The "register access failure" situation still needs an actual handler.
But at this point it makes less sense to ask folks to send mails about
it. We now have a pretty good picture of what controllers emit this and
when:
Texas Instruments PCIxx21 FireWire + CardBus + flash memory card
controller:
https://bugzilla.redhat.com/show_bug.cgi?id=608544
O2 Micro FireWire + flash memory card controller:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/881688
http://marc.info/?l=linux1394-devel&m=132309283531423
http://marc.info/?l=linux1394-devel&m=132368567907469
http://marc.info/?l=linux1394-devel&m=132516165727468
http://marc.info/?l=linux1394-devel&m=133006486927699
Pinnacle Movieboard:
commit 7f7e37115a8b6724f26d0637a04e1d35e3c59717
http://marc.info/?l=linux1394-devel&m=130714243325962
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The PCIe device
FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd FireWire Host Controller
[1180:e832] (prog-if 10 [OHCI])
is unable to access attached FireWire devices when MSI is enabled but
works if MSI is disabled.
http://www.mail-archive.com/alsa-user@lists.sourceforge.net/msg28251.html
Hence add the "disable MSI" quirks flag for this device, or in fact for
safety and simplicity for all current (R5U230, R5U231, R5U240) and
future Ricoh PCIe 1394 controllers.
Reported-by: Stefan Thomas <kontrapunktstefan@googlemail.com>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The Audigy's SB1394 controller is actually from Texas Instruments
and has the same bus reset packet generation bug, so it needs the
same quirk entry.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.36+ <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|