From b0921d5c9ed6ffa8a4d6afc5ee5f136b87445f14 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 15 Nov 2016 11:13:16 +0100 Subject: mmc: sdhci-of-esdhc: fixup PRESENT_STATE read Since commit 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()") the ESDHC driver is broken: mmc0: Card stuck in programming state! __mmc_switch mmc0: error -110 whilst initialising MMC card Since this commit __mmc_switch() uses ->card_busy(), which is sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the PRESENT_STATE register, specifically the DAT0 signal level bit. But the ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is required to make the driver work again. Signed-off-by: Michael Walle Fixes: 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()") Acked-by: Yangbo Lu Acked-by: Adrian Hunter Cc: # v4.8+ Signed-off-by: Ulf Hansson diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c index fb71c86..1bb11e4 100644 --- a/drivers/mmc/host/sdhci-of-esdhc.c +++ b/drivers/mmc/host/sdhci-of-esdhc.c @@ -66,6 +66,20 @@ static u32 esdhc_readl_fixup(struct sdhci_host *host, return ret; } } + /* + * The DAT[3:0] line signal levels and the CMD line signal level are + * not compatible with standard SDHC register. The line signal levels + * DAT[7:0] are at bits 31:24 and the command line signal level is at + * bit 23. All other bits are the same as in the standard SDHC + * register. + */ + if (spec_reg == SDHCI_PRESENT_STATE) { + ret = value & 0x000fffff; + ret |= (value >> 4) & SDHCI_DATA_LVL_MASK; + ret |= (value << 1) & SDHCI_CMD_LVL; + return ret; + } + ret = value; return ret; } diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 766df17..2570455 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -73,6 +73,7 @@ #define SDHCI_DATA_LVL_MASK 0x00F00000 #define SDHCI_DATA_LVL_SHIFT 20 #define SDHCI_DATA_0_LVL_MASK 0x00100000 +#define SDHCI_CMD_LVL 0x01000000 #define SDHCI_HOST_CONTROL 0x28 #define SDHCI_CTRL_LED 0x01 -- cgit v0.10.2 From 647f80a1f233bb66fc58fb25664d029e0f12f3ae Mon Sep 17 00:00:00 2001 From: Jaehoon Chung Date: Mon, 21 Nov 2016 10:51:48 +0900 Subject: mmc: dw_mmc: fix the error handling for dma operation When dma->start is failed,then it has to fall back to PIO mode for current transfer. But Host controller was already set to bits relevant to DMA operation. If needs to use the PIO mode, Host controller has to stop the DMA operation. (It's more stable than now.) When it occurred error, it's not running any request. Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support") Reported-by: Marek Szyprowski Signed-off-by: Jaehoon Chung Reviewed-by: Shawn Lin Cc: # v4.3+ Signed-off-by: Jaehoon Chung Signed-off-by: Ulf Hansson diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c index 50a674b..df478ae 100644 --- a/drivers/mmc/host/dw_mmc.c +++ b/drivers/mmc/host/dw_mmc.c @@ -1058,6 +1058,7 @@ static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data) spin_unlock_irqrestore(&host->irq_lock, irqflags); if (host->dma_ops->start(host, sg_len)) { + host->dma_ops->stop(host); /* We can't do DMA, try PIO for this one */ dev_dbg(host->dev, "%s: fall back to PIO mode for current transfer\n", -- cgit v0.10.2