From f91a3715db2bb44fcf08cec642e68f919b70f7f4 Mon Sep 17 00:00:00 2001 From: Alan Cox Date: Sat, 21 Jan 2006 14:59:12 +0000 Subject: [SERIAL] 8250 serial console fixes This patch resolves most of the problems with an SMP serial console race with output via the tty path. At the end of the serial console print we force enable the tx int in case we clobbered the tx interrupt status racing between the console and tty output. That way the extra tx interrupt causes the transmit path to restart not hang. It also makes the serial console printk use the FIFO. This is neccessary because some remote management devices fake serial console with FIFO and are confused into sending one packet per character over ethernet when we stall rather than filling the FIFO. In order to preserve existing reliability semantics the function waits for the serial queue to completely empty before returning. Both of these problems were identified by a Red Hat partner. Signed-off-by: Alan Cox Signed-off-by: Russell King diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index bc36edf..ff2f931 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -2164,7 +2164,7 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev) /* * Wait for transmitter & holding register to empty */ -static inline void wait_for_xmitr(struct uart_8250_port *up) +static inline void wait_for_xmitr(struct uart_8250_port *up, int bits) { unsigned int status, tmout = 10000; @@ -2178,7 +2178,7 @@ static inline void wait_for_xmitr(struct uart_8250_port *up) if (--tmout == 0) break; udelay(1); - } while ((status & BOTH_EMPTY) != BOTH_EMPTY); + } while ((status & bits) != bits); /* Wait up to 1s for flow control if necessary */ if (up->port.flags & UPF_CONS_FLOW) { @@ -2218,7 +2218,7 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) * Now, do each character */ for (i = 0; i < count; i++, s++) { - wait_for_xmitr(up); + wait_for_xmitr(up, UART_LSR_THRE); /* * Send the character out. @@ -2226,7 +2226,7 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) */ serial_out(up, UART_TX, *s); if (*s == 10) { - wait_for_xmitr(up); + wait_for_xmitr(up, UART_LSR_THRE); serial_out(up, UART_TX, 13); } } @@ -2235,8 +2235,8 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) * Finally, wait for transmitter to become empty * and restore the IER */ - wait_for_xmitr(up); - serial_out(up, UART_IER, ier); + wait_for_xmitr(up, BOTH_EMPTY); + serial_out(up, UART_IER, ier | UART_IER_THRI); } static int serial8250_console_setup(struct console *co, char *options) -- cgit v0.10.2 From ce8337cb7dc327c3ae3684ba0ee5d7cbde1fd296 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 21 Jan 2006 19:28:15 +0000 Subject: [SERIAL] Don't use ASYNC_ constants with the uart_port structure Signed-off-by: Russell King diff --git a/drivers/serial/21285.c b/drivers/serial/21285.c index 221999b..7aef751 100644 --- a/drivers/serial/21285.c +++ b/drivers/serial/21285.c @@ -366,7 +366,7 @@ static struct uart_port serial21285_port = { .irq = NO_IRQ, .fifosize = 16, .ops = &serial21285_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, }; static void serial21285_setup_ports(void) diff --git a/drivers/serial/amba-pl010.c b/drivers/serial/amba-pl010.c index 3490022..429de27 100644 --- a/drivers/serial/amba-pl010.c +++ b/drivers/serial/amba-pl010.c @@ -566,7 +566,7 @@ static struct uart_amba_port amba_ports[UART_NR] = { .uartclk = 14745600, .fifosize = 16, .ops = &amba_pl010_pops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .dtr_mask = 1 << 5, @@ -581,7 +581,7 @@ static struct uart_amba_port amba_ports[UART_NR] = { .uartclk = 14745600, .fifosize = 16, .ops = &amba_pl010_pops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .dtr_mask = 1 << 7, diff --git a/drivers/serial/clps711x.c b/drivers/serial/clps711x.c index 8ef9994..ce7b2e4 100644 --- a/drivers/serial/clps711x.c +++ b/drivers/serial/clps711x.c @@ -410,7 +410,7 @@ static struct uart_port clps711x_ports[UART_NR] = { .fifosize = 16, .ops = &clps711x_pops, .line = 0, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, }, { .iobase = SYSCON2, @@ -419,7 +419,7 @@ static struct uart_port clps711x_ports[UART_NR] = { .fifosize = 16, .ops = &clps711x_pops, .line = 1, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, } }; diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c index 587cc6a..d65ba9d 100644 --- a/drivers/serial/imx.c +++ b/drivers/serial/imx.c @@ -674,7 +674,7 @@ static struct imx_port imx_ports[] = { .irq = UART1_MINT_RX, .uartclk = 16000000, .fifosize = 8, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .ops = &imx_pops, .line = 0, }, @@ -690,7 +690,7 @@ static struct imx_port imx_ports[] = { .irq = UART2_MINT_RX, .uartclk = 16000000, .fifosize = 8, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .ops = &imx_pops, .line = 1, }, diff --git a/drivers/serial/sa1100.c b/drivers/serial/sa1100.c index 1bd9316..ff7b60b 100644 --- a/drivers/serial/sa1100.c +++ b/drivers/serial/sa1100.c @@ -665,21 +665,21 @@ void __init sa1100_register_uart(int idx, int port) sa1100_ports[idx].port.membase = (void __iomem *)&Ser1UTCR0; sa1100_ports[idx].port.mapbase = _Ser1UTCR0; sa1100_ports[idx].port.irq = IRQ_Ser1UART; - sa1100_ports[idx].port.flags = ASYNC_BOOT_AUTOCONF; + sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; break; case 2: sa1100_ports[idx].port.membase = (void __iomem *)&Ser2UTCR0; sa1100_ports[idx].port.mapbase = _Ser2UTCR0; sa1100_ports[idx].port.irq = IRQ_Ser2ICP; - sa1100_ports[idx].port.flags = ASYNC_BOOT_AUTOCONF; + sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; break; case 3: sa1100_ports[idx].port.membase = (void __iomem *)&Ser3UTCR0; sa1100_ports[idx].port.mapbase = _Ser3UTCR0; sa1100_ports[idx].port.irq = IRQ_Ser3UART; - sa1100_ports[idx].port.flags = ASYNC_BOOT_AUTOCONF; + sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; break; default: diff --git a/drivers/serial/serial_lh7a40x.c b/drivers/serial/serial_lh7a40x.c index d4a1f0e..d0490f6 100644 --- a/drivers/serial/serial_lh7a40x.c +++ b/drivers/serial/serial_lh7a40x.c @@ -506,7 +506,7 @@ static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = { .uartclk = 14745600/2, .fifosize = 16, .ops = &lh7a40x_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, }, @@ -519,7 +519,7 @@ static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = { .uartclk = 14745600/2, .fifosize = 16, .ops = &lh7a40x_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, }, @@ -532,7 +532,7 @@ static struct uart_port_lh7a40x lh7a40x_ports[DEV_NR] = { .uartclk = 14745600/2, .fifosize = 16, .ops = &lh7a40x_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 2, }, }, diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index a9e0707..0111206 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -1113,10 +1113,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xfffffe80, .mapbase = 0xfffffe80, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 25, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCI, @@ -1128,10 +1128,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)SCIF0, .mapbase = SCIF0, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 55, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1142,10 +1142,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)SCIF2, .mapbase = SCIF2, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 59, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .type = PORT_SCIF, @@ -1157,10 +1157,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xfffffe80, .mapbase = 0xfffffe80, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 25, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCI, @@ -1171,10 +1171,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xa4000150, .mapbase = 0xa4000150, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 59, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .type = PORT_SCIF, @@ -1185,10 +1185,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xa4000140, .mapbase = 0xa4000140, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 55, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 2, }, .type = PORT_IRDA, @@ -1200,10 +1200,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xA4430000, .mapbase = 0xA4430000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 25, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1215,10 +1215,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xffe00000, .mapbase = 0xffe00000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 25, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1230,10 +1230,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xffe80000, .mapbase = 0xffe80000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 43, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1245,10 +1245,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xffe00000, .mapbase = 0xffe00000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 25, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCI, @@ -1259,10 +1259,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xffe80000, .mapbase = 0xffe80000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 43, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .type = PORT_SCIF, @@ -1274,10 +1274,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xfe600000, .mapbase = 0xfe600000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 55, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1288,10 +1288,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xfe610000, .mapbase = 0xfe610000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 75, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .type = PORT_SCIF, @@ -1302,10 +1302,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xfe620000, .mapbase = 0xfe620000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 79, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 2, }, .type = PORT_SCIF, @@ -1317,10 +1317,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xffe80000, .mapbase = 0xffe80000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 43, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1332,10 +1332,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xffe00000, .mapbase = 0xffe00000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 26, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1346,10 +1346,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0xffe80000, .mapbase = 0xffe80000, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 43, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .type = PORT_SCIF, @@ -1359,10 +1359,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { #elif defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103) { .port = { - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 42, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCIF, @@ -1374,10 +1374,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0x00ffffb0, .mapbase = 0x00ffffb0, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 54, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCI, @@ -1388,10 +1388,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0x00ffffb8, .mapbase = 0x00ffffb8, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 58, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .type = PORT_SCI, @@ -1402,10 +1402,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0x00ffffc0, .mapbase = 0x00ffffc0, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 62, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 2, }, .type = PORT_SCI, @@ -1417,10 +1417,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0x00ffff78, .mapbase = 0x00ffff78, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 90, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 0, }, .type = PORT_SCI, @@ -1431,10 +1431,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0x00ffff80, .mapbase = 0x00ffff80, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 94, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 1, }, .type = PORT_SCI, @@ -1445,10 +1445,10 @@ static struct sci_port sci_ports[SCI_NPORTS] = { .port = { .membase = (void *)0x00ffff88, .mapbase = 0x00ffff88, - .iotype = SERIAL_IO_MEM, + .iotype = UPIO_MEM, .irq = 98, .ops = &sci_uart_ops, - .flags = ASYNC_BOOT_AUTOCONF, + .flags = UPF_BOOT_AUTOCONF, .line = 2, }, .type = PORT_SCI, diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c index 9a3665b..bc67442 100644 --- a/drivers/serial/sunsu.c +++ b/drivers/serial/sunsu.c @@ -669,7 +669,7 @@ static int sunsu_startup(struct uart_port *port) * if it is, then bail out, because there's likely no UART * here. */ - if (!(up->port.flags & ASYNC_BUGGY_UART) && + if (!(up->port.flags & UPF_BUGGY_UART) && (serial_inp(up, UART_LSR) == 0xff)) { printk("ttyS%d: LSR safety check engaged!\n", up->port.line); return -ENODEV; @@ -707,7 +707,7 @@ static int sunsu_startup(struct uart_port *port) up->ier = UART_IER_RLSI | UART_IER_RDI; serial_outp(up, UART_IER, up->ier); - if (up->port.flags & ASYNC_FOURPORT) { + if (up->port.flags & UPF_FOURPORT) { unsigned int icp; /* * Enable interrupts on the AST Fourport board @@ -740,7 +740,7 @@ static void sunsu_shutdown(struct uart_port *port) serial_outp(up, UART_IER, 0); spin_lock_irqsave(&up->port.lock, flags); - if (up->port.flags & ASYNC_FOURPORT) { + if (up->port.flags & UPF_FOURPORT) { /* reset interrupts on the AST Fourport board */ inb((up->port.iobase & 0xfe0) | 0x1f); up->port.mctrl |= TIOCM_OUT1; @@ -1132,7 +1132,7 @@ ebus_done: spin_lock_irqsave(&up->port.lock, flags); - if (!(up->port.flags & ASYNC_BUGGY_UART)) { + if (!(up->port.flags & UPF_BUGGY_UART)) { /* * Do a simple existence test first; if we fail this, there's * no point trying anything else. @@ -1170,7 +1170,7 @@ ebus_done: * manufacturer would be stupid enough to design a board * that conflicts with COM 1-4 --- we hope! */ - if (!(up->port.flags & ASYNC_SKIP_TEST)) { + if (!(up->port.flags & UPF_SKIP_TEST)) { serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A); status1 = serial_inp(up, UART_MSR) & 0xF0; serial_outp(up, UART_MCR, save_mcr); @@ -1371,7 +1371,7 @@ static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up) } while ((status & BOTH_EMPTY) != BOTH_EMPTY); /* Wait up to 1s for flow control if necessary */ - if (up->port.flags & ASYNC_CONS_FLOW) { + if (up->port.flags & UPF_CONS_FLOW) { tmout = 1000000; while (--tmout && ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0)) @@ -1513,7 +1513,7 @@ static int __init sunsu_serial_init(void) up->su_type == SU_PORT_KBD) continue; - up->port.flags |= ASYNC_BOOT_AUTOCONF; + up->port.flags |= UPF_BOOT_AUTOCONF; up->port.type = PORT_UNKNOWN; up->port.uartclk = (SU_BASE_BAUD * 16); -- cgit v0.10.2 From ca740803856f23dbc5b1872039291231bc131ecb Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 21 Jan 2006 20:06:14 +0000 Subject: [SERIAL] Remove UPF_AUTOPROBE and UPF_BOOT_ONLYMCA The functionality UPF_BOOT_ONLYMCA provided has been replaced by the 8250_mca module, which only registers MCA ports if MCA is present. UPF_AUTOPROBE has no functional effect - in fact, it's never tested. Only ibmasm set the flag. Signed-off-by: Russell King diff --git a/drivers/misc/ibmasm/uart.c b/drivers/misc/ibmasm/uart.c index 7e98434..9783caf 100644 --- a/drivers/misc/ibmasm/uart.c +++ b/drivers/misc/ibmasm/uart.c @@ -50,7 +50,7 @@ void ibmasm_register_uart(struct service_processor *sp) memset(&uport, 0, sizeof(struct uart_port)); uport.irq = sp->irq; uport.uartclk = 3686400; - uport.flags = UPF_AUTOPROBE | UPF_SHARE_IRQ; + uport.flags = UPF_SHARE_IRQ; uport.iotype = UPIO_MEM; uport.membase = iomem_base; diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index ff2f931..179c1f0 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -31,7 +31,6 @@ #include #include #include -#include #include #include #include @@ -2027,12 +2026,6 @@ static void serial8250_config_port(struct uart_port *port, int flags) int ret; /* - * Don't probe for MCA ports on non-MCA machines. - */ - if (up->port.flags & UPF_BOOT_ONLYMCA && !MCA_bus) - return; - - /* * Find the region that we can probe for. This in turn * tells us whether we can probe for the type of port. */ diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index ec35100..f3af477 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -245,9 +245,7 @@ struct uart_port { #define UPF_HARDPPS_CD (1 << 11) #define UPF_LOW_LATENCY (1 << 13) #define UPF_BUGGY_UART (1 << 14) -#define UPF_AUTOPROBE (1 << 15) #define UPF_MAGIC_MULTIPLIER (1 << 16) -#define UPF_BOOT_ONLYMCA (1 << 22) #define UPF_CONS_FLOW (1 << 23) #define UPF_SHARE_IRQ (1 << 24) #define UPF_BOOT_AUTOCONF (1 << 28) -- cgit v0.10.2 From ba899dbc036d24ab6b45faf64e3648a268721cc9 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 21 Jan 2006 22:45:50 +0000 Subject: [SERIAL] Make port->ops constant No one should write to the port->ops structure, so make it constant. Signed-off-by: Russell King diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index 9437704..74142b73 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -1870,7 +1870,7 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *port) mutex_lock(&state->mutex); if (state->info && state->info->flags & UIF_INITIALIZED) { - struct uart_ops *ops = port->ops; + const struct uart_ops *ops = port->ops; spin_lock_irq(&port->lock); ops->stop_tx(port); @@ -1932,7 +1932,7 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *port) } if (state->info && state->info->flags & UIF_INITIALIZED) { - struct uart_ops *ops = port->ops; + const struct uart_ops *ops = port->ops; int ret; ops->set_mctrl(port, 0); diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index f3af477..b74ff34 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -257,7 +257,7 @@ struct uart_port { unsigned int mctrl; /* current modem ctrl settings */ unsigned int timeout; /* character-based timeout */ unsigned int type; /* port type */ - struct uart_ops *ops; + const struct uart_ops *ops; unsigned int custom_divisor; unsigned int line; /* port index */ unsigned long mapbase; /* for ioremap */ -- cgit v0.10.2 From 747c8a55946ed037bf7d62454c3c599c02af2262 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 21 Jan 2006 22:50:36 +0000 Subject: [SERIAL] Make uart_info flags a bitwise type The potential for confusing the flags is fairly high. Make uart_info's flags a bitwise type so sparse can check that the right flag definitions are used with the right structure. Signed-off-by: Russell King diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index b74ff34..90f6817 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -287,6 +287,9 @@ struct uart_state { }; #define UART_XMIT_SIZE PAGE_SIZE + +typedef unsigned int __bitwise__ uif_t; + /* * This is the state information which is only valid when the port * is open; it may be freed by the core driver once the device has @@ -296,17 +299,16 @@ struct uart_state { struct uart_info { struct tty_struct *tty; struct circ_buf xmit; - unsigned int flags; + uif_t flags; /* - * These are the flags that specific to info->flags, and reflect our - * internal state. They can not be accessed via port->flags. Low - * level drivers must not change these, but may query them instead. + * Definitions for info->flags. These are _private_ to serial_core, and + * are specific to this structure. They may be queried by low level drivers. */ -#define UIF_CHECK_CD (1 << 25) -#define UIF_CTS_FLOW (1 << 26) -#define UIF_NORMAL_ACTIVE (1 << 29) -#define UIF_INITIALIZED (1 << 31) +#define UIF_CHECK_CD ((__force uif_t) (1 << 25)) +#define UIF_CTS_FLOW ((__force uif_t) (1 << 26)) +#define UIF_NORMAL_ACTIVE ((__force uif_t) (1 << 29)) +#define UIF_INITIALIZED ((__force uif_t) (1 << 31)) int blocked_open; -- cgit v0.10.2 From 27ae7a7435634820e7f7e2b922d8119f79cfc6e4 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 21 Jan 2006 22:54:06 +0000 Subject: [SERIAL] Fix UPF_ flag usage with uart_info->flags The previous change found a bug in the serial SAK handling - because we were looking for UPF_SAK set in uart_info->flags, we would never raise a SAK condition. UPF_SAK is in uart_port->flags. Signed-off-by: Russell King diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index 90f6817..1a8cd01 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -430,7 +430,7 @@ static inline int uart_handle_break(struct uart_port *port) port->sysrq = 0; } #endif - if (info->flags & UPF_SAK) + if (port->flags & UPF_SAK) do_SAK(info->tty); return 0; } -- cgit v0.10.2 From 0077d45e46fe2af3aaee5813c99268afcd0e7c0e Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 21 Jan 2006 23:03:28 +0000 Subject: [SERIAL] Make uart_port flags a bitwise type Same reasoning as commit 747c8a55946ed037bf7d62454c3c599c02af2262 but this time we're making uart_port flags a bitwise type - not all of these flags correspond with the old ASYNC_ flags, so there is the possibility for bugs if the wrong ASYNC_* constants are used. Always use UPF_* constants for uart_port->flags. Signed-off-by: Russell King diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index 74142b73..0717abf 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -332,7 +332,7 @@ uart_get_baud_rate(struct uart_port *port, struct termios *termios, struct termios *old, unsigned int min, unsigned int max) { unsigned int try, baud, altbaud = 38400; - unsigned int flags = port->flags & UPF_SPD_MASK; + upf_t flags = port->flags & UPF_SPD_MASK; if (flags == UPF_SPD_HI) altbaud = 57600; @@ -615,8 +615,9 @@ static int uart_set_info(struct uart_state *state, struct serial_struct new_serial; struct uart_port *port = state->port; unsigned long new_port; - unsigned int change_irq, change_port, old_flags, closing_wait; + unsigned int change_irq, change_port, closing_wait; unsigned int old_custom_divisor, close_delay; + upf_t old_flags, new_flags; int retval = 0; if (copy_from_user(&new_serial, newinfo, sizeof(new_serial))) @@ -655,6 +656,7 @@ static int uart_set_info(struct uart_state *state, new_serial.type != port->type; old_flags = port->flags; + new_flags = new_serial.flags; old_custom_divisor = port->custom_divisor; if (!capable(CAP_SYS_ADMIN)) { @@ -664,10 +666,10 @@ static int uart_set_info(struct uart_state *state, (close_delay != state->close_delay) || (closing_wait != state->closing_wait) || (new_serial.xmit_fifo_size != port->fifosize) || - (((new_serial.flags ^ old_flags) & ~UPF_USR_MASK) != 0)) + (((new_flags ^ old_flags) & ~UPF_USR_MASK) != 0)) goto exit; port->flags = ((port->flags & ~UPF_USR_MASK) | - (new_serial.flags & UPF_USR_MASK)); + (new_flags & UPF_USR_MASK)); port->custom_divisor = new_serial.custom_divisor; goto check_and_exit; } @@ -764,7 +766,7 @@ static int uart_set_info(struct uart_state *state, port->irq = new_serial.irq; port->uartclk = new_serial.baud_base * 16; port->flags = (port->flags & ~UPF_CHANGE_MASK) | - (new_serial.flags & UPF_CHANGE_MASK); + (new_flags & UPF_CHANGE_MASK); port->custom_divisor = new_serial.custom_divisor; state->close_delay = close_delay; state->closing_wait = closing_wait; diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h index cee302a..73b464f 100644 --- a/include/linux/serial_8250.h +++ b/include/linux/serial_8250.h @@ -26,7 +26,7 @@ struct plat_serial8250_port { unsigned char regshift; /* register shift */ unsigned char iotype; /* UPIO_* */ unsigned char hub6; - unsigned int flags; /* UPF_* flags */ + upf_t flags; /* UPF_* flags */ }; /* diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h index 1a8cd01..4041122 100644 --- a/include/linux/serial_core.h +++ b/include/linux/serial_core.h @@ -203,6 +203,8 @@ struct uart_icount { __u32 buf_overrun; }; +typedef unsigned int __bitwise__ upf_t; + struct uart_port { spinlock_t lock; /* port lock */ unsigned int iobase; /* in/out[bwl] */ @@ -230,29 +232,29 @@ struct uart_port { unsigned long sysrq; /* sysrq timeout */ #endif - unsigned int flags; - -#define UPF_FOURPORT (1 << 1) -#define UPF_SAK (1 << 2) -#define UPF_SPD_MASK (0x1030) -#define UPF_SPD_HI (0x0010) -#define UPF_SPD_VHI (0x0020) -#define UPF_SPD_CUST (0x0030) -#define UPF_SPD_SHI (0x1000) -#define UPF_SPD_WARP (0x1010) -#define UPF_SKIP_TEST (1 << 6) -#define UPF_AUTO_IRQ (1 << 7) -#define UPF_HARDPPS_CD (1 << 11) -#define UPF_LOW_LATENCY (1 << 13) -#define UPF_BUGGY_UART (1 << 14) -#define UPF_MAGIC_MULTIPLIER (1 << 16) -#define UPF_CONS_FLOW (1 << 23) -#define UPF_SHARE_IRQ (1 << 24) -#define UPF_BOOT_AUTOCONF (1 << 28) -#define UPF_IOREMAP (1 << 31) - -#define UPF_CHANGE_MASK (0x17fff) -#define UPF_USR_MASK (UPF_SPD_MASK|UPF_LOW_LATENCY) + upf_t flags; + +#define UPF_FOURPORT ((__force upf_t) (1 << 1)) +#define UPF_SAK ((__force upf_t) (1 << 2)) +#define UPF_SPD_MASK ((__force upf_t) (0x1030)) +#define UPF_SPD_HI ((__force upf_t) (0x0010)) +#define UPF_SPD_VHI ((__force upf_t) (0x0020)) +#define UPF_SPD_CUST ((__force upf_t) (0x0030)) +#define UPF_SPD_SHI ((__force upf_t) (0x1000)) +#define UPF_SPD_WARP ((__force upf_t) (0x1010)) +#define UPF_SKIP_TEST ((__force upf_t) (1 << 6)) +#define UPF_AUTO_IRQ ((__force upf_t) (1 << 7)) +#define UPF_HARDPPS_CD ((__force upf_t) (1 << 11)) +#define UPF_LOW_LATENCY ((__force upf_t) (1 << 13)) +#define UPF_BUGGY_UART ((__force upf_t) (1 << 14)) +#define UPF_MAGIC_MULTIPLIER ((__force upf_t) (1 << 16)) +#define UPF_CONS_FLOW ((__force upf_t) (1 << 23)) +#define UPF_SHARE_IRQ ((__force upf_t) (1 << 24)) +#define UPF_BOOT_AUTOCONF ((__force upf_t) (1 << 28)) +#define UPF_IOREMAP ((__force upf_t) (1 << 31)) + +#define UPF_CHANGE_MASK ((__force upf_t) (0x17fff)) +#define UPF_USR_MASK ((__force upf_t) (UPF_SPD_MASK|UPF_LOW_LATENCY)) unsigned int mctrl; /* current modem ctrl settings */ unsigned int timeout; /* character-based timeout */ -- cgit v0.10.2 From df7559d3440ff759ff6e1371ff722bb3a73a3639 Mon Sep 17 00:00:00 2001 From: Timothy Charles McGrath Date: Mon, 23 Jan 2006 09:50:09 +0000 Subject: [SERIAL] 8250 Documentation fix This fixes the documentation error for 'SERIAL_8250' in drivers/serial/Kconfig Signed-off-by: Timothy Charles McGrath Signed-off-by: Russell King diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 9fd1925d..0d38f0f 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -23,7 +23,7 @@ config SERIAL_8250 work.) To compile this driver as a module, choose M here: the - module will be called serial. + module will be called 8250. [WARNING: Do not compile this driver as a module if you are using non-standard serial ports, since the configuration information will be lost when the driver is unloaded. This limitation may be lifted -- cgit v0.10.2