From 71b149b3f740501c2d59c80de5b10f5e45051099 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Thu, 5 Apr 2012 14:14:28 +0800 Subject: ARM: at91: do not pin mux the UARTs in init_early There is no need to pinmux the UART so early in the kernel. Move it to the board init. This will also allow to finally move the gpio driver to platform device/driver. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Nicolas Ferre diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c index f43ad91..271f994 100644 --- a/arch/arm/mach-at91/board-1arm.c +++ b/arch/arm/mach-at91/board-1arm.c @@ -47,17 +47,6 @@ static void __init onearm_init_early(void) /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); } static struct macb_platform_data __initdata onearm_eth_data = { @@ -79,6 +68,16 @@ static struct at91_udc_data __initdata onearm_udc_data = { static void __init onearm_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&onearm_eth_data); diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index 7c7c682..b7d8aa7 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -52,19 +52,6 @@ static void __init afeb9260_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -180,6 +167,18 @@ static struct at91_cf_data afeb9260_cf_data = { static void __init afeb9260_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&afeb9260_usbh_data); diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c index 871717d..29d3ef0 100644 --- a/arch/arm/mach-at91/board-cam60.c +++ b/arch/arm/mach-at91/board-cam60.c @@ -49,9 +49,6 @@ static void __init cam60_init_early(void) { /* Initialize processor: 10 MHz crystal */ at91_initialize(10000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); } /* @@ -172,6 +169,8 @@ static void __init cam60_add_device_nand(void) static void __init cam60_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* SPI */ at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices)); diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index 168b3fa..44328a6 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -44,14 +44,6 @@ static void __init carmeva_init_early(void) { /* Initialize processor: 20.000 MHz crystal */ at91_initialize(20000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); } static struct macb_platform_data __initdata carmeva_eth_data = { @@ -136,6 +128,13 @@ static struct gpio_led carmeva_leds[] = { static void __init carmeva_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&carmeva_eth_data); diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index 4073e30..69951ec 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -52,31 +52,6 @@ static void __init cpu9krea_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | - ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART3 on ttyS4. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US3, 4, 0); - - /* USART4 on ttyS5. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx, Tx) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); } /* @@ -349,6 +324,30 @@ static void __init cpu9krea_board_init(void) /* NOR */ cpu9krea_add_device_nor(); /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | + ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART3 on ttyS4. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, 0); + + /* USART4 on ttyS5. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx, Tx) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&cpu9krea_usbh_data); diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c index 76c62ed..895cf2d 100644 --- a/arch/arm/mach-at91/board-cpuat91.c +++ b/arch/arm/mach-at91/board-cpuat91.c @@ -59,25 +59,6 @@ static void __init cpuat91_init_early(void) /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | - ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART2 on ttyS3 (Rx, Tx) */ - at91_register_uart(AT91RM9200_ID_US2, 3, 0); - - /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS | - ATMEL_UART_RTS); } static struct macb_platform_data __initdata cpuat91_eth_data = { @@ -158,6 +139,24 @@ static struct platform_device *platform_devices[] __initdata = { static void __init cpuat91_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | + ATMEL_UART_RTS); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | + ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART2 on ttyS3 (Rx, Tx) */ + at91_register_uart(AT91RM9200_ID_US2, 3, 0); + + /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS | + ATMEL_UART_RTS); at91_add_device_serial(); /* LEDs. */ at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds)); diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index d984435..ad7f9f0 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -50,9 +50,6 @@ static void __init csb337_init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); - - /* DBGU on ttyS0 */ - at91_register_uart(0, 0, 0); } static struct macb_platform_data __initdata csb337_eth_data = { @@ -226,6 +223,8 @@ static struct gpio_led csb_leds[] = { static void __init csb337_board_init(void) { /* Serial */ + /* DBGU on ttyS0 */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&csb337_eth_data); diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c index 0c9935d..7c8b05a 100644 --- a/arch/arm/mach-at91/board-csb637.c +++ b/arch/arm/mach-at91/board-csb637.c @@ -44,9 +44,6 @@ static void __init csb637_init_early(void) { /* Initialize processor: 3.6864 MHz crystal */ at91_initialize(3686400); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); } static struct macb_platform_data __initdata csb637_eth_data = { @@ -115,6 +112,8 @@ static void __init csb637_board_init(void) /* LED(s) */ at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds)); /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&csb637_eth_data); diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index a189b9f..bd10172 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -44,17 +44,6 @@ static void __init eb9200_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART2 on ttyS2. (Rx, Tx) - IRDA */ - at91_register_uart(AT91RM9200_ID_US2, 2, 0); } static struct macb_platform_data __initdata eb9200_eth_data = { @@ -98,6 +87,16 @@ static struct i2c_board_info __initdata eb9200_i2c_devices[] = { static void __init eb9200_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART2 on ttyS2. (Rx, Tx) - IRDA */ + at91_register_uart(AT91RM9200_ID_US2, 2, 0); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&eb9200_eth_data); diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 307c530..2510825 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -53,12 +53,6 @@ static void __init ecb_at91init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx & Tx only) */ - at91_register_uart(AT91RM9200_ID_US0, 1, 0); } static struct macb_platform_data __initdata ecb_at91eth_data = { @@ -149,6 +143,11 @@ static struct spi_board_info __initdata ecb_at91spi_devices[] = { static void __init ecb_at91board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx & Tx only) */ + at91_register_uart(AT91RM9200_ID_US0, 1, 0); at91_add_device_serial(); /* Ethernet */ diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c index 7df6a9b..bebeae8 100644 --- a/arch/arm/mach-at91/board-eco920.c +++ b/arch/arm/mach-at91/board-eco920.c @@ -40,9 +40,6 @@ static void __init eco920_init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1); - - /* DBGU on ttyS0. (Rx & Tx only */ - at91_register_uart(0, 0, 0); } static struct macb_platform_data __initdata eco920_eth_data = { @@ -100,6 +97,8 @@ static struct spi_board_info eco920_spi_devices[] = { static void __init eco920_board_init(void) { + /* DBGU on ttyS0. (Rx & Tx only */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); at91_add_device_eth(&eco920_eth_data); at91_add_device_usbh(&eco920_usbh_data); diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c index 6dcc962..47658f7 100644 --- a/arch/arm/mach-at91/board-flexibity.c +++ b/arch/arm/mach-at91/board-flexibity.c @@ -41,9 +41,6 @@ static void __init flexibity_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); } /* USB Host port */ @@ -140,6 +137,8 @@ static struct gpio_led flexibity_leds[] = { static void __init flexibity_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&flexibity_usbh_data); diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index bb07807..33411e6 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -61,41 +61,6 @@ static void __init foxg20_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS - | ATMEL_UART_RTS - | ATMEL_UART_DTR - | ATMEL_UART_DSR - | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, 0); - - /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US3, 4, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART4 on ttyS5. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* Set the internal pull-up resistor on DRXD */ - at91_set_A_periph(AT91_PIN_PB14, 1); - } /* @@ -238,6 +203,39 @@ static struct i2c_board_info __initdata foxg20_i2c_devices[] = { static void __init foxg20_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS + | ATMEL_UART_RTS + | ATMEL_UART_DTR + | ATMEL_UART_DSR + | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, 0); + + /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART4 on ttyS5. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); + + /* Set the internal pull-up resistor on DRXD */ + at91_set_A_periph(AT91_PIN_PB14, 1); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&foxg20_usbh_data); diff --git a/arch/arm/mach-at91/board-gsia18s.c b/arch/arm/mach-at91/board-gsia18s.c index 230e719..3e0dfa6 100644 --- a/arch/arm/mach-at91/board-gsia18s.c +++ b/arch/arm/mach-at91/board-gsia18s.c @@ -41,38 +41,6 @@ static void __init gsia18s_init_early(void) { stamp9g20_init_early(); - - /* - * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI). - * Used for Internal Analog Modem. - */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS | ATMEL_UART_RTS | - ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - /* - * USART1 on ttyS2 (Rx, Tx, CTS, RTS). - * Used for GPS or WiFi or Data stream. - */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS | ATMEL_UART_RTS); - /* - * USART2 on ttyS3 (Rx, Tx, CTS, RTS). - * Used for External Modem. - */ - at91_register_uart(AT91SAM9260_ID_US2, 3, - ATMEL_UART_CTS | ATMEL_UART_RTS); - /* - * USART3 on ttyS4 (Rx, Tx, RTS). - * Used for RS-485. - */ - at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS); - - /* - * USART4 on ttyS5 (Rx, Tx). - * Used for TRX433 Radio Module. - */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); } /* @@ -558,6 +526,37 @@ static int __init gsia18s_power_off_init(void) static void __init gsia18s_board_init(void) { + /* + * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI). + * Used for Internal Analog Modem. + */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS | ATMEL_UART_RTS | + ATMEL_UART_DTR | ATMEL_UART_DSR | + ATMEL_UART_DCD | ATMEL_UART_RI); + /* + * USART1 on ttyS2 (Rx, Tx, CTS, RTS). + * Used for GPS or WiFi or Data stream. + */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS | ATMEL_UART_RTS); + /* + * USART2 on ttyS3 (Rx, Tx, CTS, RTS). + * Used for External Modem. + */ + at91_register_uart(AT91SAM9260_ID_US2, 3, + ATMEL_UART_CTS | ATMEL_UART_RTS); + /* + * USART3 on ttyS4 (Rx, Tx, RTS). + * Used for RS-485. + */ + at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS); + + /* + * USART4 on ttyS5 (Rx, Tx). + * Used for TRX433 Radio Module. + */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); stamp9g20_board_init(); at91_add_device_usbh(&usbh_data); at91_add_device_udc(&udc_data); diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c index 3e858ed..f46b3eb 100644 --- a/arch/arm/mach-at91/board-kafa.c +++ b/arch/arm/mach-at91/board-kafa.c @@ -50,12 +50,6 @@ static void __init kafa_init_early(void) /* Set up the LEDs */ at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); } static struct macb_platform_data __initdata kafa_eth_data = { @@ -77,6 +71,11 @@ static struct at91_udc_data __initdata kafa_udc_data = { static void __init kafa_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&kafa_eth_data); diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index ccbc8be..e71b9e1 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -53,18 +53,6 @@ static void __init kb9202_init_early(void) /* Set up the LEDs */ at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx & Tx only) */ - at91_register_uart(AT91RM9200_ID_US0, 1, 0); - - /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */ - at91_register_uart(AT91RM9200_ID_US1, 2, 0); - - /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */ - at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); } static struct macb_platform_data __initdata kb9202_eth_data = { @@ -113,6 +101,17 @@ static struct atmel_nand_data __initdata kb9202_nand_data = { static void __init kb9202_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1 (Rx & Tx only) */ + at91_register_uart(AT91RM9200_ID_US0, 1, 0); + + /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */ + at91_register_uart(AT91RM9200_ID_US1, 2, 0); + + /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&kb9202_eth_data); diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index c456fdc..d2f4cc1 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -55,12 +55,6 @@ static void __init neocore926_init_early(void) { /* Initialize processor: 20 MHz crystal */ at91_initialize(20000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -338,6 +332,11 @@ static struct ac97c_platform_data neocore926_ac97_data = { static void __init neocore926_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c index b4a12fc..7fe6383 100644 --- a/arch/arm/mach-at91/board-pcontrol-g20.c +++ b/arch/arm/mach-at91/board-pcontrol-g20.c @@ -40,17 +40,6 @@ static void __init pcontrol_g20_init_early(void) { stamp9g20_init_early(); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */ - at91_register_uart(AT91SAM9260_ID_US4, 3, 0); } static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { @@ -199,6 +188,16 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = { static void __init pcontrol_g20_board_init(void) { + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */ + at91_register_uart(AT91SAM9260_ID_US4, 3, 0); stamp9g20_board_init(); at91_add_device_usbh(&usbh_data); at91_add_device_eth(&macb_data); diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index 4ca56cd..b45c0a5 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -48,14 +48,6 @@ static void __init picotux200_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); } static struct macb_platform_data __initdata picotux200_eth_data = { @@ -103,6 +95,13 @@ static struct platform_device picotux200_flash = { static void __init picotux200_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&picotux200_eth_data); diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index 189d3fe..0c61bf0 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -52,20 +52,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.000 MHz crystal */ at91_initialize(12000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -231,6 +217,19 @@ static struct gpio_led ek_leds[] = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c index d5ce630..4a0b097 100644 --- a/arch/arm/mach-at91/board-rm9200dk.c +++ b/arch/arm/mach-at91/board-rm9200dk.c @@ -53,14 +53,6 @@ static void __init dk_init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); } static struct macb_platform_data __initdata dk_eth_data = { @@ -188,6 +180,13 @@ static struct gpio_led dk_leds[] = { static void __init dk_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&dk_eth_data); diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index 32d35cb..b687261 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -53,14 +53,6 @@ static void __init ek_init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); } static struct macb_platform_data __initdata ek_eth_data = { @@ -159,6 +151,13 @@ static struct gpio_led ek_leds[] = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&ek_eth_data); diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c index 2c84463..10d8730 100644 --- a/arch/arm/mach-at91/board-rsi-ews.c +++ b/arch/arm/mach-at91/board-rsi-ews.c @@ -38,20 +38,6 @@ static void __init rsi_ews_init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9); - - /* DBGU on ttyS0. (Rx & Tx only) */ - /* This one is for debugging */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - /* Dialin/-out modem interface */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART3 on ttyS4. (Rx, Tx, RTS) */ - /* RS485 communication */ - at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS); } /* @@ -202,6 +188,19 @@ static struct platform_device rsiews_nor_flash = { static void __init rsi_ews_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + /* This one is for debugging */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + /* Dialin/-out modem interface */ + at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART3 on ttyS4. (Rx, Tx, RTS) */ + /* RS485 communication */ + at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS); at91_add_device_serial(); at91_set_gpio_output(AT91_PIN_PA21, 0); /* Ethernet */ diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index dee44cb..5343dab 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -51,17 +51,6 @@ static void __init ek_init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -182,6 +171,16 @@ static struct at91_mmc_data __initdata ek_mmc_data = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index 6da17b5..7b3c391 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -54,17 +54,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -317,6 +306,16 @@ static void __init ek_add_device_buttons(void) {} static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index e91c4af..4406f6b 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -61,9 +61,6 @@ static void __init ek_init_early(void) /* Setup the LEDs */ at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); } /* @@ -574,6 +571,8 @@ static struct gpio_led ek_leds[] = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 4424873..983cb98 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -57,12 +57,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 16.367 MHz crystal */ at91_initialize(16367660); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -409,6 +403,11 @@ static struct at91_can_data ek_can_data = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 05f8467..3d61553 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -65,17 +65,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -369,6 +358,16 @@ static struct i2c_board_info __initdata ek_i2c_devices[] = { static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index be2ca19..9a87f0b0 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -53,13 +53,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.000 MHz crystal */ at91_initialize(12000000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 not connected on the -EK board */ - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -454,6 +447,12 @@ static struct platform_device *devices[] __initdata = { static void __init ek_board_init(void) { /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 not connected on the -EK board */ + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9G45_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB HS Host */ at91_add_device_usbh_ohci(&ek_usbh_hs_data); diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index 23f383a..be3239f 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -42,12 +42,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.000 MHz crystal */ at91_initialize(12000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); } /* @@ -293,6 +287,11 @@ static void __init ek_add_device_buttons(void) {} static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB HS */ at91_add_device_usba(&ek_usba_udc_data); diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c index 1a6774a..9d446f1b 100644 --- a/arch/arm/mach-at91/board-snapper9260.c +++ b/arch/arm/mach-at91/board-snapper9260.c @@ -43,15 +43,6 @@ static void __init snapper9260_init_early(void) { at91_initialize(18432000); - - /* Debug on ttyS0 */ - at91_register_uart(0, 0, 0); - - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS | ATMEL_UART_RTS); - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS | ATMEL_UART_RTS); - at91_register_uart(AT91SAM9260_ID_US2, 3, 0); } static struct at91_usbh_data __initdata snapper9260_usbh_data = { @@ -167,6 +158,14 @@ static void __init snapper9260_board_init(void) snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31); i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1); + /* Debug on ttyS0 */ + at91_register_uart(0, 0, 0); + + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS | ATMEL_UART_RTS); + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS | ATMEL_UART_RTS); + at91_register_uart(AT91SAM9260_ID_US2, 3, 0); at91_add_device_serial(); at91_add_device_usbh(&snapper9260_usbh_data); at91_add_device_udc(&snapper9260_udc_data); diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 38a7ca5..ee86f9d 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -36,41 +36,6 @@ void __init stamp9g20_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ at91_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); -} - -static void __init stamp9g20evb_init_early(void) -{ - stamp9g20_init_early(); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); -} - -static void __init portuxg20_init_early(void) -{ - stamp9g20_init_early(); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART4 on ttyS5. (Rx, Tx only) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx, Tx only) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); } /* @@ -251,6 +216,8 @@ void add_w1(void) void __init stamp9g20_board_init(void) { /* Serial */ + /* DGBU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* NAND */ add_device_nand(); @@ -266,6 +233,22 @@ void __init stamp9g20_board_init(void) static void __init portuxg20_board_init(void) { + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); + + /* USART4 on ttyS5. (Rx, Tx only) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx, Tx only) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); stamp9g20_board_init(); /* USB Host */ at91_add_device_usbh(&usbh_data); @@ -283,6 +266,10 @@ static void __init portuxg20_board_init(void) static void __init stamp9g20evb_board_init(void) { + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); stamp9g20_board_init(); /* USB Host */ at91_add_device_usbh(&usbh_data); @@ -300,7 +287,7 @@ MACHINE_START(PORTUXG20, "taskit PortuxG20") /* Maintainer: taskit GmbH */ .timer = &at91sam926x_timer, .map_io = at91_map_io, - .init_early = portuxg20_init_early, + .init_early = stamp9g20_init_early, .init_irq = at91_init_irq_default, .init_machine = portuxg20_board_init, MACHINE_END @@ -309,7 +296,7 @@ MACHINE_START(STAMP9G20, "taskit Stamp9G20") /* Maintainer: taskit GmbH */ .timer = &at91sam926x_timer, .map_io = at91_map_io, - .init_early = stamp9g20evb_init_early, + .init_early = stamp9g20_init_early, .init_irq = at91_init_irq_default, .init_machine = stamp9g20evb_board_init, MACHINE_END diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index ee482eb..332ecd4 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -53,9 +53,6 @@ static void __init ek_init_early(void) { /* Initialize processor: 12.00 MHz crystal */ at91_initialize(12000000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); } /* @@ -322,6 +319,8 @@ static void __init ek_add_device_leds(void) static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index e94a04e..db8d25c 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -61,20 +61,6 @@ static void __init yl9200_init_early(void) /* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */ at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART0 on ttyS2. (Rx & Tx only to JP3) */ - at91_register_uart(AT91RM9200_ID_US0, 2, 0); - - /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */ - at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS); } /* @@ -558,6 +544,19 @@ void __init yl9200_add_device_video(void) {} static void __init yl9200_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART0 on ttyS2. (Rx & Tx only to JP3) */ + at91_register_uart(AT91RM9200_ID_US0, 2, 0); + + /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS); at91_add_device_serial(); /* Ethernet */ at91_add_device_eth(&yl9200_eth_data); -- cgit v0.10.2