From af756bbccff85504ce05c63a50f80b9d7823c500 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 11 Jan 2016 14:35:24 -0800 Subject: ARM: dts: Fix omap5 PMIC control lines for RTC writes The palmas PMIC has two control lines that need to be muxed properly for things to work. The sys_nirq pin is used for interrupts, and msecure pin is used for enabling writes to some PMIC registers. Without these pins configured properly things can fail in mysterious ways. For example, we can't update the RTC registers on palmas PMIC unless the msecure pin is configured. And this is probably the reason why we had RTC missing from the omap5 dts file. According to "OMAP5430 ES2.0 Data Manual [Public] VErsion A (Rev. F)" swps052f.pdf, mux mode 1 is for sys_drm_msecure so in theory there's should be no need to configure it as a GPIO pin. However, it seems there are some reliability issues using the msecure mux mode. And the TI trees configure the msecure pin as GPIO out high instead. As the PMIC only cares that the msecure line is high to allow access to the RTC registers, let's use a GPIO hog as suggested by Nishanth Menon . Also the use of the internal pull was considered but supposedly that may not be capable of keeping the line high in a noisy environment. If we ever see high security omap5 products in the mainline tree, those need to skip the msecure pin muxing and ignore setting the GPIO hog. Chances are the related pin mux registers are locked in that case and the msecure pin is managed by whatever software may be running in the ARM TrustZone. Who knows what the original intention of the msecure pin was. Maybe it was supposed to prevent the system time to be set back for some game demo modes to time out? Anyways, it seems that later PMICs like tps659037 have recycled this pin for "powerhold" and devices like beagle-x15 do not need changes to the msecure pin configuration. To avoid further confusion with TWL variant PMICs, beagle-x15 does not have a back-up battery for RTC palmas. Instead the mcp79410 RTC is used with rtc-ds1307 driver. There is a "powerhold" jumper j5 holes near the palmas PMIC, and shorting it seems to power up beagle-x15 automatically. It is unknown if it also has other side effects to the beagle-x15 power up sequence. Cc: stable@vger.kernel.org # v4.4 Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi index 5cf76a1..7de5a77 100644 --- a/arch/arm/boot/dts/omap5-board-common.dtsi +++ b/arch/arm/boot/dts/omap5-board-common.dtsi @@ -130,6 +130,16 @@ }; }; +&gpio8 { + /* TI trees use GPIO instead of msecure, see also muxing */ + p234 { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "gpio8_234/msecure"; + }; +}; + &omap5_pmx_core { pinctrl-names = "default"; pinctrl-0 = < @@ -213,6 +223,13 @@ >; }; + /* TI trees use GPIO mode; msecure mode does not work reliably? */ + palmas_msecure_pins: palmas_msecure_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */ + >; + }; + usbhost_pins: pinmux_usbhost_pins { pinctrl-single,pins = < 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ @@ -278,6 +295,12 @@ &usbhost_wkup_pins >; + palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */ + >; + }; + usbhost_wkup_pins: pinmux_usbhost_wkup_pins { pinctrl-single,pins = < 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ @@ -345,6 +368,8 @@ interrupt-controller; #interrupt-cells = <2>; ti,system-power-controller; + pinctrl-names = "default"; + pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>; extcon_usb3: palmas_usb { compatible = "ti,palmas-usb-vid"; -- cgit v0.10.2 From c08659d431b40ad5beb97d7dde49ad9796cb812c Mon Sep 17 00:00:00 2001 From: "H. Nikolaus Schaller" Date: Tue, 5 Jan 2016 13:01:37 +0100 Subject: ARM: dts: omap5-board-common: enable rtc and charging of backup battery tested on OMP5432 EVM Cc: stable@vger.kernel.org # v4.4 Signed-off-by: H. Nikolaus Schaller Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi index 7de5a77..41e80e7 100644 --- a/arch/arm/boot/dts/omap5-board-common.dtsi +++ b/arch/arm/boot/dts/omap5-board-common.dtsi @@ -383,6 +383,14 @@ #clock-cells = <0>; }; + rtc { + compatible = "ti,palmas-rtc"; + interrupt-parent = <&palmas>; + interrupts = <8 IRQ_TYPE_NONE>; + ti,backup-battery-chargeable; + ti,backup-battery-charge-high-current; + }; + palmas_pmic { compatible = "ti,palmas-pmic"; interrupt-parent = <&palmas>; -- cgit v0.10.2 From 02f1cc3c1a121c70cdf95e986f7f2fb4323cc5a3 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Mon, 11 Jan 2016 15:26:12 -0600 Subject: ARM: omap2plus_defconfig: enable SPLIT and DWARF4 CONFIG_DEBUG_INFO_SPLIT will split debug info on .dwo files. This will generate a smaller vmlinux and smaller .ko modules, which will be easier to ship on certain products. CONFIG_DEBUG_INFO_DWARF4 will generate debug info in DWARF4 format, which ends up being larger, but improves the probability of resolving variables in optmized code. Signed-off-by: Felipe Balbi [tony@atomide.com: this makes initramfs quite a bit smaller] Signed-off-by: Tony Lindgren diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index c5e1943..0b3e471 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -449,6 +449,8 @@ CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_PRINTK_TIME=y CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_INFO_SPLIT=y +CONFIG_DEBUG_INFO_DWARF4=y CONFIG_MAGIC_SYSRQ=y CONFIG_SCHEDSTATS=y CONFIG_TIMER_STATS=y -- cgit v0.10.2 From 2800971f731e4491b71f44bf311452ab0f94a062 Mon Sep 17 00:00:00 2001 From: Dave Gerlach Date: Fri, 17 Jul 2015 16:08:01 -0500 Subject: ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using wkup_m3 mailbox are sent without triggering any further interrupts. This is needed to achieve lower power numbers during CPU idle on AM33xx. Signed-off-by: Dave Gerlach [s-anna@ti.com: revise commit description] Signed-off-by: Suman Anna Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index d23e252..ee26e2a 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -399,6 +399,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <8>; mbox_wkupm3: wkup_m3 { + ti,mbox-send-noirq; ti,mbox-tx = <0 0 0>; ti,mbox-rx = <0 0 3>; }; -- cgit v0.10.2 From cf19f3ab89de1c088387ce744b0d4723be35b068 Mon Sep 17 00:00:00 2001 From: Keerthy Date: Fri, 17 Jul 2015 16:08:02 -0500 Subject: ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using wkup_m3 mailbox are sent without triggering any further interrupts. This is required to be able to send multiple messages to the WkupM3 after the mailbox usage logic adjustment in the wkup_m3_ipc driver. Signed-off-by: Keerthy Acked-by: Dave Gerlach [s-anna@ti.com: revise commit description] Signed-off-by: Suman Anna Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index de8791a..ca36b7a 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -249,6 +249,7 @@ ti,mbox-num-users = <4>; ti,mbox-num-fifos = <8>; mbox_wkupm3: wkup_m3 { + ti,mbox-send-noirq; ti,mbox-tx = <0 0 0>; ti,mbox-rx = <0 0 3>; }; -- cgit v0.10.2 From 4850d43143e72563556b9ba371e26b2b48599321 Mon Sep 17 00:00:00 2001 From: Suman Anna Date: Mon, 14 Sep 2015 18:37:12 -0500 Subject: ARM: OMAP2+: Remove legacy mailbox device instantiation The legacy-style mailbox device creation is supported currently only for OMAP3, as all other SoCs are DT-boot only. Even on this SoC, there are no client drivers that utilize these mailbox devices. So, clean up the legacy-style mailbox device instantiation logic. The mailbox devices are already present and supported for the DT boot on OMAP3. Signed-off-by: Suman Anna Signed-off-by: Tony Lindgren diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 9374da3..f0f9901 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -18,7 +18,6 @@ #include #include #include -#include #include #include @@ -66,32 +65,6 @@ static int __init omap3_l3_init(void) } omap_postcore_initcall(omap3_l3_init); -#if defined(CONFIG_OMAP2PLUS_MBOX) || defined(CONFIG_OMAP2PLUS_MBOX_MODULE) -static inline void __init omap_init_mbox(void) -{ - struct omap_hwmod *oh; - struct platform_device *pdev; - struct omap_mbox_pdata *pdata; - - oh = omap_hwmod_lookup("mailbox"); - if (!oh) { - pr_err("%s: unable to find hwmod\n", __func__); - return; - } - if (!oh->dev_attr) { - pr_err("%s: hwmod doesn't have valid attrs\n", __func__); - return; - } - - pdata = (struct omap_mbox_pdata *)oh->dev_attr; - pdev = omap_device_build("omap-mailbox", -1, oh, pdata, sizeof(*pdata)); - WARN(IS_ERR(pdev), "%s: could not build device, err %ld\n", - __func__, PTR_ERR(pdev)); -} -#else -static inline void omap_init_mbox(void) { } -#endif /* CONFIG_OMAP2PLUS_MBOX */ - static inline void omap_init_sti(void) {} #if defined(CONFIG_SND_SOC) || defined(CONFIG_SND_SOC_MODULE) @@ -246,7 +219,6 @@ static int __init omap2_init_devices(void) omap_init_audio(); /* If dtb is there, the devices will be created dynamically */ if (!of_have_populated_dt()) { - omap_init_mbox(); omap_init_mcspi(); omap_init_sham(); omap_init_aes(); -- cgit v0.10.2 From d9db59103305eb5ec2a86369f32063e9921b6ac5 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 14 Jan 2016 12:20:47 -0800 Subject: ARM: OMAP2+: Fix wait_dll_lock_timed for rodata We don't want to be writing to .text so it can be set rodata. Fix error "Unable to handle kernel paging request at virtual address c012396c" in wait_dll_lock_timed if CONFIG_DEBUG_RODATA is selected. As these counters are for debugging only and unused, we can just remove them. Cc: Kees Cook Cc: Laura Abbott Cc: Nishanth Menon Cc: Richard Woodruff Cc: Russell King Cc: Tero Kristo Acked-by: Nicolas Pitre Cc: stable@vger.kernel.org # v4.0+ Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be non-executable") Signed-off-by: Tony Lindgren diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S index eafd120..787cfda 100644 --- a/arch/arm/mach-omap2/sleep34xx.S +++ b/arch/arm/mach-omap2/sleep34xx.S @@ -289,12 +289,6 @@ wait_sdrc_ready: bic r5, r5, #0x40 str r5, [r4] -/* - * PC-relative stores lead to undefined behaviour in Thumb-2: use a r7 as a - * base instead. - * Be careful not to clobber r7 when maintaing this code. - */ - is_dll_in_lock_mode: /* Is dll in lock mode? */ ldr r4, sdrc_dlla_ctrl @@ -302,11 +296,7 @@ is_dll_in_lock_mode: tst r5, #0x4 bne exit_nonoff_modes @ Return if locked /* wait till dll locks */ - adr r7, kick_counter wait_dll_lock_timed: - ldr r4, wait_dll_lock_counter - add r4, r4, #1 - str r4, [r7, #wait_dll_lock_counter - kick_counter] ldr r4, sdrc_dlla_status /* Wait 20uS for lock */ mov r6, #8 @@ -330,9 +320,6 @@ kick_dll: orr r6, r6, #(1<<3) @ enable dll str r6, [r4] dsb - ldr r4, kick_counter - add r4, r4, #1 - str r4, [r7] @ kick_counter b wait_dll_lock_timed exit_nonoff_modes: @@ -360,15 +347,6 @@ sdrc_dlla_status: .word SDRC_DLLA_STATUS_V sdrc_dlla_ctrl: .word SDRC_DLLA_CTRL_V - /* - * When exporting to userspace while the counters are in SRAM, - * these 2 words need to be at the end to facilitate retrival! - */ -kick_counter: - .word 0 -wait_dll_lock_counter: - .word 0 - ENTRY(omap3_do_wfi_sz) .word . - omap3_do_wfi -- cgit v0.10.2 From eeaf9646aca89d097861caa24d9818434e48810e Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 14 Jan 2016 12:20:47 -0800 Subject: ARM: OMAP2+: Fix l2dis_3630 for rodata We don't want to write to .text section. Let's move l2dis_3630 to .data and access it via a pointer. For calculating the offset, let's optimize out the add and do it in ldr/str as suggested by Nicolas Pitre . Cc: Kees Cook Cc: Laura Abbott Cc: Nishanth Menon Cc: Richard Woodruff Cc: Russell King Cc: Tero Kristo Cc: stable@vger.kernel.org # v4.0+ Acked-by: Nicolas Pitre Cc: stable@vger.kernel.org # v4.0+ Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be non-executable") Signed-off-by: Tony Lindgren diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S index 787cfda..5659d96 100644 --- a/arch/arm/mach-omap2/sleep34xx.S +++ b/arch/arm/mach-omap2/sleep34xx.S @@ -86,8 +86,9 @@ ENTRY(enable_omap3630_toggle_l2_on_restore) stmfd sp!, {lr} @ save registers on stack /* Setup so that we will disable and enable l2 */ mov r1, #0x1 - adrl r2, l2dis_3630 @ may be too distant for plain adr - str r1, [r2] + adrl r3, l2dis_3630_offset @ may be too distant for plain adr + ldr r2, [r3] @ value for offset + str r1, [r2, r3] @ write to l2dis_3630 ldmfd sp!, {pc} @ restore regs and return ENDPROC(enable_omap3630_toggle_l2_on_restore) @@ -415,7 +416,9 @@ ENTRY(omap3_restore) cmp r2, #0x0 @ Check if target power state was OFF or RET bne logic_l1_restore - ldr r0, l2dis_3630 + adr r1, l2dis_3630_offset @ address for offset + ldr r0, [r1] @ value for offset + ldr r0, [r1, r0] @ value at l2dis_3630 cmp r0, #0x1 @ should we disable L2 on 3630? bne skipl2dis mrc p15, 0, r0, c1, c0, 1 @@ -484,7 +487,9 @@ l2_inv_gp: mov r12, #0x2 smc #0 @ Call SMI monitor (smieq) logic_l1_restore: - ldr r1, l2dis_3630 + adr r0, l2dis_3630_offset @ adress for offset + ldr r1, [r0] @ value for offset + ldr r1, [r0, r1] @ value at l2dis_3630 cmp r1, #0x1 @ Test if L2 re-enable needed on 3630 bne skipl2reen mrc p15, 0, r1, c1, c0, 1 @@ -513,6 +518,10 @@ control_stat: .word CONTROL_STAT control_mem_rta: .word CONTROL_MEM_RTA_CTRL +l2dis_3630_offset: + .long l2dis_3630 - . + + .data l2dis_3630: .word 0 -- cgit v0.10.2 From a5311d4d13df80bd71a9e47f9ecaf327f478fab1 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 14 Jan 2016 12:20:47 -0800 Subject: ARM: OMAP2+: Fix save_secure_ram_context for rodata We don't want to write to .text and we can move save_secure_ram_context into .data as it all gets copied into SRAM anyways. Cc: Kees Cook Cc: Laura Abbott Cc: Nishanth Menon Cc: Richard Woodruff Cc: Russell King Cc: Sergei Shtylyov Cc: Tero Kristo Acked-by: Nicolas Pitre Cc: stable@vger.kernel.org # v4.0+ Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be non-executable") Signed-off-by: Tony Lindgren diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S index 5659d96..8e2a7ac 100644 --- a/arch/arm/mach-omap2/sleep34xx.S +++ b/arch/arm/mach-omap2/sleep34xx.S @@ -92,8 +92,12 @@ ENTRY(enable_omap3630_toggle_l2_on_restore) ldmfd sp!, {pc} @ restore regs and return ENDPROC(enable_omap3630_toggle_l2_on_restore) - .text -/* Function to call rom code to save secure ram context */ +/* + * Function to call rom code to save secure ram context. This gets + * relocated to SRAM, so it can be all in .data section. Otherwise + * we need to initialize api_params separately. + */ + .data .align 3 ENTRY(save_secure_ram_context) stmfd sp!, {r4 - r11, lr} @ save registers on stack @@ -127,6 +131,8 @@ ENDPROC(save_secure_ram_context) ENTRY(save_secure_ram_context_sz) .word . - save_secure_ram_context + .text + /* * ====================== * == Idle entry point == -- cgit v0.10.2 From 0a0b13275558c32bbf6241464a7244b1ffd5afb3 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 14 Jan 2016 12:20:47 -0800 Subject: ARM: OMAP2+: Fix l2_inv_api_params for rodata We don't want to write to .text, so let's move l2_inv_api_params to .data and access it via a pointer. Cc: Kees Cook Cc: Laura Abbott Cc: Nishanth Menon Cc: Richard Woodruff Cc: Russell King Cc: Tero Kristo Acked-by: Nicolas Pitre Cc: stable@vger.kernel.org # v4.0+ Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be non-executable") Signed-off-by: Tony Lindgren diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S index 8e2a7ac..1b9f052 100644 --- a/arch/arm/mach-omap2/sleep34xx.S +++ b/arch/arm/mach-omap2/sleep34xx.S @@ -436,12 +436,14 @@ skipl2dis: and r1, #0x700 cmp r1, #0x300 beq l2_inv_gp + adr r0, l2_inv_api_params_offset + ldr r3, [r0] + add r3, r3, r0 @ r3 points to dummy parameters mov r0, #40 @ set service ID for PPA mov r12, r0 @ copy secure Service ID in r12 mov r1, #0 @ set task id for ROM code in r1 mov r2, #4 @ set some flags in r2, r6 mov r6, #0xff - adr r3, l2_inv_api_params @ r3 points to dummy parameters dsb @ data write barrier dmb @ data memory barrier smc #1 @ call SMI monitor (smi #1) @@ -475,8 +477,8 @@ skipl2dis: b logic_l1_restore .align -l2_inv_api_params: - .word 0x1, 0x00 +l2_inv_api_params_offset: + .long l2_inv_api_params - . l2_inv_gp: /* Execute smi to invalidate L2 cache */ mov r12, #0x1 @ set up to invalidate L2 @@ -531,6 +533,10 @@ l2dis_3630_offset: l2dis_3630: .word 0 + .data +l2_inv_api_params: + .word 0x1, 0x00 + /* * Internal functions */ -- cgit v0.10.2 From 4da597d16602d14405b71a18d45e1c59f28f0fd2 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 14 Jan 2016 12:20:48 -0800 Subject: ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata We don't want to write to .text so let's move ppa_zero_params and ppa_por_params to .data and access them via pointers. Note that I have not been able to test as we I don't have a HS omap4 to test with. The code has been changed in similar way as for omap3 though. Cc: Kees Cook Cc: Laura Abbott Cc: Nishanth Menon Cc: Richard Woodruff Cc: Russell King Cc: Tero Kristo Acked-by: Nicolas Pitre Cc: stable@vger.kernel.org # v4.0+ Fixes: 1e6b48116a95 ("ARM: mm: allow non-text sections to be non-executable") Signed-off-by: Tony Lindgren diff --git a/arch/arm/mach-omap2/sleep44xx.S b/arch/arm/mach-omap2/sleep44xx.S index 9b09d85..c7a3b4a 100644 --- a/arch/arm/mach-omap2/sleep44xx.S +++ b/arch/arm/mach-omap2/sleep44xx.S @@ -29,12 +29,6 @@ dsb .endm -ppa_zero_params: - .word 0x0 - -ppa_por_params: - .word 1, 0 - #ifdef CONFIG_ARCH_OMAP4 /* @@ -266,7 +260,9 @@ ENTRY(omap4_cpu_resume) beq skip_ns_smp_enable ppa_actrl_retry: mov r0, #OMAP4_PPA_CPU_ACTRL_SMP_INDEX - adr r3, ppa_zero_params @ Pointer to parameters + adr r1, ppa_zero_params_offset + ldr r3, [r1] + add r3, r3, r1 @ Pointer to ppa_zero_params mov r1, #0x0 @ Process ID mov r2, #0x4 @ Flag mov r6, #0xff @@ -303,7 +299,9 @@ skip_ns_smp_enable: ldr r0, =OMAP4_PPA_L2_POR_INDEX ldr r1, =OMAP44XX_SAR_RAM_BASE ldr r4, [r1, #L2X0_PREFETCH_CTRL_OFFSET] - adr r3, ppa_por_params + adr r1, ppa_por_params_offset + ldr r3, [r1] + add r3, r3, r1 @ Pointer to ppa_por_params str r4, [r3, #0x04] mov r1, #0x0 @ Process ID mov r2, #0x4 @ Flag @@ -328,6 +326,8 @@ skip_l2en: #endif b cpu_resume @ Jump to generic resume +ppa_por_params_offset: + .long ppa_por_params - . ENDPROC(omap4_cpu_resume) #endif /* CONFIG_ARCH_OMAP4 */ @@ -380,4 +380,13 @@ ENTRY(omap_do_wfi) nop ldmfd sp!, {pc} +ppa_zero_params_offset: + .long ppa_zero_params - . ENDPROC(omap_do_wfi) + + .data +ppa_zero_params: + .word 0 + +ppa_por_params: + .word 1, 0 -- cgit v0.10.2 From 143c6fe3a415edf2dde3f507b3a00998b4c4001e Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Tue, 12 Jan 2016 08:11:04 -0800 Subject: ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules With recent omap assembly fixes for CONFIG_DEBUG_RODATA, we can now use DEBUG_RODATA. Let's enable ARM_KERNMEM_PERMS so that DEBUG_RODATA gets selected by default. This way we can make sure any related issues are caught early. And while testing things on various devices, I noticed we're missing few loadable modules to make things more usable: - USB Ethernet for smsc75xx, we only have smsc97xx right now - Basic USB serial drivers for things like ftdi and pl2303 ports - Blinking leds with pca963x Signed-off-by: Tony Lindgren diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 0b3e471..a715174 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -50,6 +50,7 @@ CONFIG_SOC_AM33XX=y CONFIG_SOC_AM43XX=y CONFIG_SOC_DRA7XX=y CONFIG_ARM_THUMBEE=y +CONFIG_ARM_KERNMEM_PERMS=y CONFIG_ARM_ERRATA_411920=y CONFIG_ARM_ERRATA_430973=y CONFIG_SMP=y @@ -177,6 +178,7 @@ CONFIG_TI_CPTS=y CONFIG_AT803X_PHY=y CONFIG_SMSC_PHY=y CONFIG_USB_USBNET=m +CONFIG_USB_NET_SMSC75XX=m CONFIG_USB_NET_SMSC95XX=m CONFIG_USB_ALI_M5632=y CONFIG_USB_AN2720=y @@ -354,6 +356,11 @@ CONFIG_USB_MUSB_DSPS=m CONFIG_USB_INVENTRA_DMA=y CONFIG_USB_TI_CPPI41_DMA=y CONFIG_USB_DWC3=m +CONFIG_USB_SERIAL=m +CONFIG_USB_SERIAL_GENERIC=y +CONFIG_USB_SERIAL_SIMPLE=m +CONFIG_USB_SERIAL_FTDI_SIO=m +CONFIG_USB_SERIAL_PL2303=m CONFIG_USB_TEST=m CONFIG_AM335X_PHY_USB=y CONFIG_USB_GADGET=m @@ -387,6 +394,7 @@ CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=m CONFIG_LEDS_GPIO=m CONFIG_LEDS_PWM=m +CONFIG_LEDS_PCA963X=m CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_ONESHOT=m -- cgit v0.10.2 From 84d92dd3b6b785a6737f0409a920de31fb83343a Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:46 +0100 Subject: ARM: mvebu: kirkwood: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Signed-off-by: Gregory CLEMENT diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts index 1db6f2c..8082d64 100644 --- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts +++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts @@ -131,6 +131,7 @@ chip-delay = <40>; status = "okay"; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v0.10.2 From 293de94cd66cded940849545f47c701cc36c0931 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Mon, 21 Dec 2015 11:33:45 +0100 Subject: ARM: mvebu: ix4-300d: Add compatible property to "partitions" node As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible property to "partitions" node"), the "partitions" subnode of an SPI FLASH device node must have a compatible property. The partitions are no longer detected if it is not present. Signed-off-by: Geert Uytterhoeven Acked-by: Brian Norris Signed-off-by: Gregory CLEMENT diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index 13cf69a..fb9e1bb 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -152,6 +152,7 @@ nand-on-flash-bbt; partitions { + compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; -- cgit v0.10.2 From 144e08abe80080c9c2cf0a06e40f1bc8150674eb Mon Sep 17 00:00:00 2001 From: Roger Shimizu Date: Thu, 21 Jan 2016 23:38:44 +0900 Subject: ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wxl/wsxl For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be converted to "gpio1 " in dts file. e.g. gpio 40 should be "gpio1 8" Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin definition: - gpio-leds: "lswxl:blue:power" pin - gpio-leds: "lswxl:red:func" pin - gpio-leds: "lswxl:red:hdderr0" pin - gpio-leds: "lswxl:red:hdderr1" pin - gpio-fan: low/high/alarm pin The pin/bank issue was found when discussing Debian Bug #810894 [https://bugs.debian.org/810894#47] Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl") Reported-by: Arnaud Patard (Rtp) Signed-off-by: Roger Shimizu Reviewed-by: Andrew Lunn Signed-off-by: Gregory CLEMENT diff --git a/arch/arm/boot/dts/kirkwood-lswxl.dts b/arch/arm/boot/dts/kirkwood-lswxl.dts index f5db16a..0e93f6d 100644 --- a/arch/arm/boot/dts/kirkwood-lswxl.dts +++ b/arch/arm/boot/dts/kirkwood-lswxl.dts @@ -1,7 +1,8 @@ /* * Device Tree file for Buffalo Linkstation LS-WXL/WSXL * - * Copyright (C) 2015, rogershimizu@gmail.com + * Copyright (C) 2015, 2016 + * Roger Shimizu * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -156,21 +157,21 @@ button@1 { label = "Function Button"; linux,code = ; - gpios = <&gpio1 41 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; }; button@2 { label = "Power-on Switch"; linux,code = ; linux,input-type = <5>; - gpios = <&gpio1 42 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; }; button@3 { label = "Power-auto Switch"; linux,code = ; linux,input-type = <5>; - gpios = <&gpio1 43 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; }; }; @@ -185,12 +186,12 @@ led@1 { label = "lswxl:blue:func"; - gpios = <&gpio1 36 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; }; led@2 { label = "lswxl:red:alarm"; - gpios = <&gpio1 49 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; }; led@3 { @@ -200,23 +201,23 @@ led@4 { label = "lswxl:blue:power"; - gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; }; led@5 { label = "lswxl:red:func"; - gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; default-state = "keep"; }; led@6 { label = "lswxl:red:hdderr0"; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; }; led@7 { label = "lswxl:red:hdderr1"; - gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; }; }; @@ -225,15 +226,15 @@ pinctrl-0 = <&pmx_fan_low &pmx_fan_high &pmx_fan_lock>; pinctrl-names = "default"; - gpios = <&gpio0 47 GPIO_ACTIVE_LOW - &gpio0 48 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW + &gpio1 15 GPIO_ACTIVE_LOW>; gpio-fan,speed-map = <0 3 1500 2 3250 1 5000 0>; - alarm-gpios = <&gpio1 49 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; }; restart_poweroff { @@ -256,7 +257,7 @@ enable-active-high; regulator-always-on; regulator-boot-on; - gpio = <&gpio0 37 GPIO_ACTIVE_HIGH>; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; }; hdd_power0: regulator@2 { compatible = "regulator-fixed"; -- cgit v0.10.2 From 6f86e9adc53b4c0a2a4283692216d119019f0b8d Mon Sep 17 00:00:00 2001 From: Roger Shimizu Date: Thu, 21 Jan 2016 23:38:45 +0900 Subject: ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wvl/vl For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be converted to "gpio1 " in dts file. e.g. gpio 40 should be "gpio1 8" The pin/bank issue was found when discussing Debian Bug #810894 [https://bugs.debian.org/810894#47] Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl") Reported-by: Arnaud Patard (Rtp) Signed-off-by: Roger Shimizu Reviewed-by: Andrew Lunn Signed-off-by: Gregory CLEMENT diff --git a/arch/arm/boot/dts/kirkwood-lswvl.dts b/arch/arm/boot/dts/kirkwood-lswvl.dts index 09eed3c..28fd9ab 100644 --- a/arch/arm/boot/dts/kirkwood-lswvl.dts +++ b/arch/arm/boot/dts/kirkwood-lswvl.dts @@ -1,7 +1,8 @@ /* * Device Tree file for Buffalo Linkstation LS-WVL/VL * - * Copyright (C) 2015, rogershimizu@gmail.com + * Copyright (C) 2015, 2016 + * Roger Shimizu * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -156,21 +157,21 @@ button@1 { label = "Function Button"; linux,code = ; - gpios = <&gpio0 45 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; }; button@2 { label = "Power-on Switch"; linux,code = ; linux,input-type = <5>; - gpios = <&gpio0 46 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; }; button@3 { label = "Power-auto Switch"; linux,code = ; linux,input-type = <5>; - gpios = <&gpio0 47 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; }; }; @@ -185,38 +186,38 @@ led@1 { label = "lswvl:red:alarm"; - gpios = <&gpio0 36 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; }; led@2 { label = "lswvl:red:func"; - gpios = <&gpio0 37 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; }; led@3 { label = "lswvl:amber:info"; - gpios = <&gpio0 38 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; }; led@4 { label = "lswvl:blue:func"; - gpios = <&gpio0 39 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; }; led@5 { label = "lswvl:blue:power"; - gpios = <&gpio0 40 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; default-state = "keep"; }; led@6 { label = "lswvl:red:hdderr0"; - gpios = <&gpio0 34 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; }; led@7 { label = "lswvl:red:hdderr1"; - gpios = <&gpio0 35 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; }; }; @@ -233,7 +234,7 @@ 3250 1 5000 0>; - alarm-gpios = <&gpio0 43 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; }; restart_poweroff { -- cgit v0.10.2 From e98bd707e39d52d8bef8622e6e7b0ab4bd0ed8d0 Mon Sep 17 00:00:00 2001 From: Roger Shimizu Date: Thu, 21 Jan 2016 23:38:46 +0900 Subject: ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wxl/wsxl The GPIOs controlling the LEDs, listed below, are active high, not low: - gpio-leds: "lswxl:blue:power" pin - gpio-leds: "lswxl:red:func" pin - gpio-leds: "lswxl:red:hdderr{0,1}" pin Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl") Signed-off-by: Roger Shimizu Reviewed-by: Andrew Lunn Signed-off-by: Gregory CLEMENT diff --git a/arch/arm/boot/dts/kirkwood-lswxl.dts b/arch/arm/boot/dts/kirkwood-lswxl.dts index 0e93f6d..b13ec20 100644 --- a/arch/arm/boot/dts/kirkwood-lswxl.dts +++ b/arch/arm/boot/dts/kirkwood-lswxl.dts @@ -201,23 +201,23 @@ led@4 { label = "lswxl:blue:power"; - gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + default-state = "keep"; }; led@5 { label = "lswxl:red:func"; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; }; led@6 { label = "lswxl:red:hdderr0"; - gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; }; led@7 { label = "lswxl:red:hdderr1"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>; }; }; -- cgit v0.10.2 From 0418138e2ffd90f4a00b263593f2e199db87321d Mon Sep 17 00:00:00 2001 From: Roger Shimizu Date: Thu, 21 Jan 2016 23:38:47 +0900 Subject: ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wvl/vl The GPIOs controlling the LEDs, listed below, are active high, not low: - gpio-leds: "lswvl:red:alarm" pin - gpio-leds: "lswvl:red:func" pin - gpio-leds: "lswvl:amber:info" pin - gpio-leds: "lswvl:blue:func" pin - gpio-leds: "lswvl:red:hdderr{0,1}" pin Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl") Signed-off-by: Roger Shimizu Reviewed-by: Andrew Lunn Signed-off-by: Gregory CLEMENT diff --git a/arch/arm/boot/dts/kirkwood-lswvl.dts b/arch/arm/boot/dts/kirkwood-lswvl.dts index 28fd9ab..36eec73 100644 --- a/arch/arm/boot/dts/kirkwood-lswvl.dts +++ b/arch/arm/boot/dts/kirkwood-lswvl.dts @@ -186,22 +186,22 @@ led@1 { label = "lswvl:red:alarm"; - gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; }; led@2 { label = "lswvl:red:func"; - gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; }; led@3 { label = "lswvl:amber:info"; - gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; }; led@4 { label = "lswvl:blue:func"; - gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; }; led@5 { @@ -212,12 +212,12 @@ led@6 { label = "lswvl:red:hdderr0"; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; }; led@7 { label = "lswvl:red:hdderr1"; - gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; }; }; -- cgit v0.10.2 From ff61ee84e7aa5842d9e33c0b442f0b43a6a44eaf Mon Sep 17 00:00:00 2001 From: Roger Shimizu Date: Fri, 22 Jan 2016 00:00:36 +0900 Subject: ARM: dts: orion5x: gpio pin fixes for linkstation lswtgl Here're a few gpio pin related fixes: - remove pinctrl-0 definition from pinctrl, since those pins are used in other places such as gpio-fan and regulators. - keep initial state of power led - fix for alarm pin of gpio-fan. Fixes: dc57844a736f ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl") Signed-off-by: Roger Shimizu Reviewed-by: Andrew Lunn Signed-off-by: Gregory CLEMENT diff --git a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts b/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts index 3daec91..4207882 100644 --- a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts +++ b/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts @@ -1,7 +1,8 @@ /* * Device Tree file for Buffalo Linkstation LS-WTGL * - * Copyright (C) 2015, Roger Shimizu + * Copyright (C) 2015, 2016 + * Roger Shimizu * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -69,8 +70,6 @@ internal-regs { pinctrl: pinctrl@10000 { - pinctrl-0 = <&pmx_usb_power &pmx_power_hdd - &pmx_fan_low &pmx_fan_high &pmx_fan_lock>; pinctrl-names = "default"; pmx_led_power: pmx-leds { @@ -162,6 +161,7 @@ led@1 { label = "lswtgl:blue:power"; gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + default-state = "keep"; }; led@2 { @@ -188,7 +188,7 @@ 3250 1 5000 0>; - alarm-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; }; restart_poweroff { -- cgit v0.10.2 From 20437f79f6627a31752f422688a6047c25cefcf1 Mon Sep 17 00:00:00 2001 From: Neil Armstrong Date: Fri, 22 Jan 2016 17:15:51 +0100 Subject: ARM: OMAP: Add PWM dmtimer platform data quirks In order to set the currently platform dependent dmtimer functions pointers as platform data for the pwm-omap-dmtimer platform driver, add it to plat-omap auxdata_lookup table. Suggested-by: Tony Lindgren Signed-off-by: Neil Armstrong Signed-off-by: Tony Lindgren diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index e781e4f..a935d28 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -23,6 +23,8 @@ #include #include #include +#include +#include #include "common.h" #include "common-board-devices.h" @@ -449,6 +451,24 @@ void omap_auxdata_legacy_init(struct device *dev) dev->platform_data = &twl_gpio_auxdata; } +/* Dual mode timer PWM callbacks platdata */ +#if IS_ENABLED(CONFIG_OMAP_DM_TIMER) +struct pwm_omap_dmtimer_pdata pwm_dmtimer_pdata = { + .request_by_node = omap_dm_timer_request_by_node, + .free = omap_dm_timer_free, + .enable = omap_dm_timer_enable, + .disable = omap_dm_timer_disable, + .get_fclk = omap_dm_timer_get_fclk, + .start = omap_dm_timer_start, + .stop = omap_dm_timer_stop, + .set_load = omap_dm_timer_set_load, + .set_match = omap_dm_timer_set_match, + .set_pwm = omap_dm_timer_set_pwm, + .set_prescaler = omap_dm_timer_set_prescaler, + .write_counter = omap_dm_timer_write_counter, +}; +#endif + /* * Few boards still need auxdata populated before we populate * the dev entries in of_platform_populate(). @@ -502,6 +522,9 @@ static struct of_dev_auxdata omap_auxdata_lookup[] __initdata = { OF_DEV_AUXDATA("ti,am4372-wkup-m3", 0x44d00000, "44d00000.wkup_m3", &wkup_m3_data), #endif +#if IS_ENABLED(CONFIG_OMAP_DM_TIMER) + OF_DEV_AUXDATA("ti,omap-dmtimer-pwm", 0, NULL, &pwm_dmtimer_pdata), +#endif #if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) OF_DEV_AUXDATA("ti,omap4-iommu", 0x4a066000, "4a066000.mmu", &omap4_iommu_pdata), -- cgit v0.10.2 From 0ea24daae053a9ba65d2f3eb20523002c1a8af38 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 21 Jan 2016 11:03:20 -0600 Subject: ARM: dts: Fix wl12xx missing clocks that cause hangs The tcxo-clock-frequency binding is listed as optional, but without it the wl12xx used on the torpedo + wireless may hang. Scanning also appears broken without this patch. Signed-off-by: Adam Ford Fixes: 687c27676151 ("ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 7fed0bd..93f50d67 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -143,6 +143,7 @@ interrupt-parent = <&gpio5>; interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */ ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; }; }; -- cgit v0.10.2 From 929e883f2bfdf68d4bd3aec43912e956417005c7 Mon Sep 17 00:00:00 2001 From: Mohamed Jamsheeth Hajanajubudeen Date: Fri, 11 Dec 2015 17:06:26 +0530 Subject: ARM: dts: at91: sama5d4: fix instance id of DBGU Change instance id of DBGU to 45. Signed-off-by: Mohamed Jamsheeth Hajanajubudeen Fixes: 7c661394c56c ("ARM: at91: dt: add device tree file for SAMA5D4 SoC") Cc: stable@vger.kernel.org # 3.18+ Signed-off-by: Nicolas Ferre diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index b8032bc..db1151c 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -1342,7 +1342,7 @@ dbgu: serial@fc069000 { compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xfc069000 0x200>; - interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>; + interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; clocks = <&dbgu_clk>; -- cgit v0.10.2 From 1a469ae2ced763fc0d4edb3c9d7b4188deee950c Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Tue, 19 Jan 2016 02:30:59 +0100 Subject: ARM: dts: at91: at91sam9n12ek: fix panel compatible string Properly use qiaodian as the vendor prefix for the panel. Signed-off-by: Alexandre Belloni Signed-off-by: Nicolas Ferre diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index ca4ddf8..626c67d 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -215,7 +215,7 @@ }; panel: panel { - compatible = "qd,qd43003c0-40", "simple-panel"; + compatible = "qiaodian,qd43003c0-40", "simple-panel"; backlight = <&backlight>; power-supply = <&panel_reg>; #address-cells = <1>; -- cgit v0.10.2 From 6c482fd15d4ff211ce0e63a628cbda17201b33a0 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 12 Jan 2016 15:55:12 +0100 Subject: ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0 After 57a38effa598 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091) the macb0 interface has difficulties to come back from power saving mode if address not explicitly set up. As the micrel phy on the board is actually configured to show up at address 1 we use this explicitly. Adding the phy node and its real address fixes the issue. The phy IRQ and associated pinmux node is also added. Signed-off-by: Nicolas Ferre Acked-by: Alexandre Belloni Cc: stable@vger.kernel.org # 4.4+ // manual merge needed diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index 77ddff0..e683856 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -114,9 +114,15 @@ macb0: ethernet@f8008000 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_macb0_default>; + pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>; phy-mode = "rmii"; status = "okay"; + + ethernet-phy@1 { + reg = <0x1>; + interrupt-parent = <&pioA>; + interrupts = <73 IRQ_TYPE_LEVEL_LOW>; + }; }; pdmic@f8018000 { @@ -300,6 +306,10 @@ bias-disable; }; + pinctrl_macb0_phy_irq: macb0_phy_irq { + pinmux = ; + }; + pinctrl_pdmic_default: pdmic_default { pinmux = , ; -- cgit v0.10.2 From aae6b18f5c95b9dc78de66d1e27e8afeee2763b7 Mon Sep 17 00:00:00 2001 From: Wenyou Yang Date: Wed, 27 Jan 2016 13:16:24 +0800 Subject: ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0 On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend state. Signed-off-by: Wenyou Yang [nicolas.ferre@atmel.com: adapt to newer kernel] Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board") Cc: # 4.1+ Signed-off-by: Nicolas Ferre diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts index 2d4a331..4e98cda 100644 --- a/arch/arm/boot/dts/at91-sama5d4ek.dts +++ b/arch/arm/boot/dts/at91-sama5d4ek.dts @@ -160,8 +160,15 @@ }; macb0: ethernet@f8020000 { + pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>; phy-mode = "rmii"; status = "okay"; + + ethernet-phy@1 { + reg = <0x1>; + interrupt-parent = <&pioE>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + }; }; mmc1: mmc@fc000000 { @@ -193,6 +200,10 @@ pinctrl@fc06a000 { board { + pinctrl_macb0_phy_irq: macb0_phy_irq { + atmel,pins = + ; + }; pinctrl_mmc0_cd: mmc0_cd { atmel,pins = ; -- cgit v0.10.2 From f505dba762ae826bb68978a85ee5c8ced7dea8d7 Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Fri, 15 Jan 2016 09:30:18 +0100 Subject: ARM: dts: at91: sama5d4 xplained: properly mux phy interrupt No interrupt were received from the phy because PIOE 1 may not be properly muxed. It prevented proper link detection, especially since commit 321beec5047a ("net: phy: Use interrupts when available in NOLINK state") disables polling. Cc: # 4.4 Signed-off-by: Alexandre Belloni Signed-off-by: Nicolas Ferre diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts index 131614f..8cf9999 100644 --- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts @@ -86,6 +86,8 @@ macb0: ethernet@f8020000 { phy-mode = "rmii"; status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>; phy0: ethernet-phy@1 { interrupt-parent = <&pioE>; @@ -152,6 +154,10 @@ atmel,pins = ; }; + pinctrl_macb0_phy_irq: macb0_phy_irq_0 { + atmel,pins = + ; + }; }; }; }; -- cgit v0.10.2 From e873cc022ce5e2c04bbc53b5874494b657e29d3f Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Wed, 27 Jan 2016 11:03:02 +0100 Subject: ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of "edge falling". Signed-off-by: Nicolas Ferre Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board") Cc: # 4.1+ diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts index 8cf9999..569026e 100644 --- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts @@ -91,7 +91,7 @@ phy0: ethernet-phy@1 { interrupt-parent = <&pioE>; - interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; reg = <1>; }; }; -- cgit v0.10.2 From 84fb225ad257442d879a1f57c79184e31fb17aea Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Mon, 28 Dec 2015 15:52:04 +0200 Subject: ARM: dts: am4372: fix irq type for arm twd and global timer As per ARM documentation PPI(0) ID27 - global timer interrupt is rising-edge sensitive. PPI(2) ID29 - twd interrupt is rising-edge sensitive. and the same is proved by GIC distributor register value GIC_DIST_CONFIG(0xC04) = 0x7DC00000. Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING for ARM TWD and Global timers. Signed-off-by: Grygorii Strashko Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index d3abd27..92068fb 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -73,7 +73,7 @@ global_timer: timer@48240200 { compatible = "arm,cortex-a9-global-timer"; reg = <0x48240200 0x100>; - interrupts = ; + interrupts = ; interrupt-parent = <&gic>; clocks = <&mpu_periphclk>; }; @@ -81,7 +81,7 @@ local_timer: timer@48240600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x48240600 0x100>; - interrupts = ; + interrupts = ; interrupt-parent = <&gic>; clocks = <&mpu_periphclk>; }; -- cgit v0.10.2 From 95e7d03e086846df987121e6894f05aae44ff132 Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Mon, 28 Dec 2015 15:52:39 +0200 Subject: ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types Now IRQs for Pixcir Tangoc touchscreen are defined using IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich do not correspond HW. Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files and use correct flag IRQ_TYPE_EDGE_FALLING for irq types. While here, remove duplicated irq declaration for pixcir_ts@5c node in am437x-gp-evm.dts. Signed-off-by: Grygorii Strashko Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 64d4332..ecd09ab 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -590,8 +590,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pixcir_ts_pins>; reg = <0x5c>; - interrupt-parent = <&gpio3>; - interrupts = <22 0>; attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; @@ -599,7 +597,7 @@ * 0x264 represents the offset of padconf register of * gpio3_22 from am43xx_pinmux base. */ - interrupts-extended = <&gpio3 22 IRQ_TYPE_NONE>, + interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>, <&am43xx_pinmux 0x264>; interrupt-names = "tsc", "wakeup"; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index 746fd2b..d580e2b 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -491,7 +491,7 @@ pinctrl-0 = <&pixcir_ts_pins>; reg = <0x5c>; interrupt-parent = <&gpio1>; - interrupts = <17 0>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>; -- cgit v0.10.2 From 2dfdc7544219729ddf5c8e8404348b72e0d0d7c5 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Fri, 1 Jan 2016 10:38:28 -0600 Subject: ARM: dts: LogicPD Torpedo: Revert Duplicative Entries Revert commit 7cd6ca770d1b ("ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit") It was already done and it is just a duplicate. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi index 93f50d67..0080532 100644 --- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi @@ -112,14 +112,6 @@ clock-frequency = <400000>; }; -&i2c2 { - clock-frequency = <400000>; -}; - -&i2c3 { - clock-frequency = <400000>; -}; - /* * Only found on the wireless SOM. For the SOM without wireless, the pins for * MMC3 can be routed with jumpers to the second MMC slot on the devkit and -- cgit v0.10.2 From bd73da8c3b9dd1cc8957bb2c90757fffb51b1396 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Wed, 30 Dec 2015 15:39:00 +0200 Subject: ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address Fix SB-SOM EEPROM I2C address Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index 77bb8e1..0f1d425 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -108,9 +108,9 @@ pinctrl-0 = <&i2c5_pins_default>; clock-frequency = <400000>; - eeprom_base: atmel@50 { + eeprom_base: atmel@54 { compatible = "atmel,24c08"; - reg = <0x50>; + reg = <0x54>; pagesize = <16>; }; -- cgit v0.10.2 From c71ff38e325fa41a610b051030db41d9cdf011ef Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Wed, 30 Dec 2015 15:39:01 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2 Setup USB2 to act in "HOST" mode by default. Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index c538826..513ec62 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -588,7 +588,7 @@ }; &usb2 { - dr_mode = "peripheral"; + dr_mode = "host"; }; &mcasp3 { -- cgit v0.10.2 From e46c408fc74b96a562590bf7c7c2a2e18f88fb06 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Wed, 30 Dec 2015 15:39:02 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency On-board SPI flash cat act at 48Mhz SPI bus frequency. Update the DT frequency property. Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index 513ec62..cb9a518 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -492,14 +492,14 @@ pinctrl-names = "default"; pinctrl-0 = <&qspi1_pins>; - spi-max-frequency = <20000000>; + spi-max-frequency = <48000000>; spi_flash: spi_flash@0 { #address-cells = <1>; #size-cells = <1>; compatible = "spansion,m25p80", "jedec,spi-nor"; reg = <0>; /* CS0 */ - spi-max-frequency = <20000000>; + spi-max-frequency = <48000000>; partition@0 { label = "uboot"; -- cgit v0.10.2 From 5ddfc9fc9b2cd6be71bd002f0f36198d487d5085 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Wed, 30 Dec 2015 15:39:03 +0200 Subject: ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux Fix UART3 pinmux. Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am57xx-sbc-am57x.dts b/arch/arm/boot/dts/am57xx-sbc-am57x.dts index 0f1d425..988e996 100644 --- a/arch/arm/boot/dts/am57xx-sbc-am57x.dts +++ b/arch/arm/boot/dts/am57xx-sbc-am57x.dts @@ -25,8 +25,8 @@ &dra7_pmx_core { uart3_pins_default: uart3_pins_default { pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ - DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ + DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */ + DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */ >; }; -- cgit v0.10.2 From 2fe8bab2b0b1ab72dc54814c5d904a1044b36acc Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Wed, 30 Dec 2015 15:39:04 +0200 Subject: ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux Fix CPSW EMAC pinmux Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index cb9a518..9e0153a 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -167,7 +167,7 @@ DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLUP | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ + DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ >; }; -- cgit v0.10.2 From ab342c77fa60a30fce4d4228f88fd1b7bf566055 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Wed, 30 Dec 2015 15:39:05 +0200 Subject: ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings Update Eth PHY settings to make it possible to run both phys at 1Gbps. Signed-off-by: Dmitry Lifshitz Signed-off-by: Tony Lindgren diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index 9e0153a..8d93882 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -559,13 +559,13 @@ &cpsw_emac0 { phy_id = <&davinci_mdio>, <0>; - phy-mode = "rgmii"; + phy-mode = "rgmii-txid"; dual_emac_res_vlan = <0>; }; &cpsw_emac1 { phy_id = <&davinci_mdio>, <1>; - phy-mode = "rgmii"; + phy-mode = "rgmii-txid"; dual_emac_res_vlan = <1>; }; -- cgit v0.10.2 From d99875eebfebec5432981273fac0547f3e34f2d7 Mon Sep 17 00:00:00 2001 From: Amitoj Kaur Chawla Date: Fri, 22 Jan 2016 23:38:38 +0530 Subject: bus: vexpress-config: Add missing of_node_put for_each_compatible_node performs an of_node_get on each iteration, so to break out of the loop an of_node_put is required. Found using Coccinelle. The semantic patch used for this is as follows: // @@ expression e; local idexpression n; @@ for_each_compatible_node(n, ...) { ... when != of_node_put(n) when != e = n ( return n; + of_node_put(n); ? return ...; ) ... } // Acked-by: Liviu Dudau Signed-off-by: Amitoj Kaur Chawla Signed-off-by: Sudeep Holla diff --git a/drivers/bus/vexpress-config.c b/drivers/bus/vexpress-config.c index 6575c0f..c3cb76b 100644 --- a/drivers/bus/vexpress-config.c +++ b/drivers/bus/vexpress-config.c @@ -192,8 +192,10 @@ static int __init vexpress_config_init(void) /* Need the config devices early, before the "normal" devices... */ for_each_compatible_node(node, NULL, "arm,vexpress,config-bus") { err = vexpress_config_populate(node); - if (err) + if (err) { + of_node_put(node); break; + } } return err; -- cgit v0.10.2 From aeb2ee5683e51305aff274d8b0a50af69b3ab310 Mon Sep 17 00:00:00 2001 From: Robin Murphy Date: Thu, 7 Jan 2016 12:01:59 +0000 Subject: arm64: dts: Add missing DMA Abort interrupt to Juno The DMA-330 has an "irq_abort" interrupt line on which it signals faults separately from the "irq[n:0]" channel interrupts. On Juno, this is wired up to SPI 92; add it to the DT so that DMAC faults are correctly reported for the driver to reset the thing, rather than leaving it locked up and waiting to time out. CC: Liviu Dudau CC: Lorenzo Pieralisi Signed-off-by: Robin Murphy Signed-off-by: Sudeep Holla diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi index dd5158e..e5b59ca 100644 --- a/arch/arm64/boot/dts/arm/juno-base.dtsi +++ b/arch/arm64/boot/dts/arm/juno-base.dtsi @@ -115,6 +115,7 @@ , , , + , , , , -- cgit v0.10.2 From 047a555f95fec4bcb8adfc37eb6fb1026fb3026a Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Sat, 23 Jan 2016 23:06:28 +0900 Subject: bus: uniphier-system-bus: revive tristate prompt At first, commit 4b7f48d395a7 ("bus: uniphier-system-bus: add UniPhier System Bus driver") introduced this driver as a tristate one. Then, commit 326ea45aa827 ("bus: uniphier: allow only built-in driver") temporarily made it boolean in order to fix a link error in case it is compiled as a module. The root cause was fixed by commit b80443c2211c ("of/platform: export of_default_bus_match_table"). Now this driver can really be a module. Signed-off-by: Masahiro Yamada Signed-off-by: Olof Johansson diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig index 129d47b..9a92c07 100644 --- a/drivers/bus/Kconfig +++ b/drivers/bus/Kconfig @@ -132,7 +132,7 @@ config SUNXI_RSB and AC100/AC200 ICs. config UNIPHIER_SYSTEM_BUS - bool "UniPhier System Bus driver" + tristate "UniPhier System Bus driver" depends on ARCH_UNIPHIER && OF default y help -- cgit v0.10.2 From 567fdd9d91db09c0af563930253ef9dbb28ddb5b Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Mon, 25 Jan 2016 20:33:07 +0900 Subject: ARM: realview: use const and __initconst for smp_operations This newly added code missed the global fixup by commit 75305275a721 ("ARM: use const and __initconst for smp_operations"). So fix it now. Also, add missing "static" qualifier. Signed-off-by: Masahiro Yamada Signed-off-by: Olof Johansson diff --git a/arch/arm/mach-realview/platsmp-dt.c b/arch/arm/mach-realview/platsmp-dt.c index 6558539..6964e88 100644 --- a/arch/arm/mach-realview/platsmp-dt.c +++ b/arch/arm/mach-realview/platsmp-dt.c @@ -80,7 +80,7 @@ static void __init realview_smp_prepare_cpus(unsigned int max_cpus) virt_to_phys(versatile_secondary_startup)); } -struct smp_operations realview_dt_smp_ops __initdata = { +static const struct smp_operations realview_dt_smp_ops __initconst = { .smp_prepare_cpus = realview_smp_prepare_cpus, .smp_secondary_init = versatile_secondary_init, .smp_boot_secondary = versatile_boot_secondary, -- cgit v0.10.2 From c38ac80eb4b0d0c78aad9b8978a3c0da3da01ead Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Mon, 25 Jan 2016 20:33:42 +0900 Subject: ARM: tango: use const and __initconst for smp_operations This newly added code missed the global fixup by commit 75305275a721 ("ARM: use const and __initconst for smp_operations"). So fix it now. Signed-off-by: Masahiro Yamada Acked-by: Marc Gonzalez Signed-off-by: Olof Johansson diff --git a/arch/arm/mach-tango/platsmp.c b/arch/arm/mach-tango/platsmp.c index a18d5a3..a21f55e 100644 --- a/arch/arm/mach-tango/platsmp.c +++ b/arch/arm/mach-tango/platsmp.c @@ -9,7 +9,7 @@ static int tango_boot_secondary(unsigned int cpu, struct task_struct *idle) return 0; } -static struct smp_operations tango_smp_ops __initdata = { +static const struct smp_operations tango_smp_ops __initconst = { .smp_boot_secondary = tango_boot_secondary, }; -- cgit v0.10.2 From 990591ee39b6e2d0ad1f281a476c62cebbc7ee7c Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Mon, 25 Jan 2016 20:40:44 +0900 Subject: ARM: tango: use "depends on" instead of "if" after prompt This platform was recently added, so missed the global fixup by commit e32465429490 ("ARM: use "depends on" for SoC configs instead of "if" after prompt"). Fix it now. Signed-off-by: Masahiro Yamada Acked-by: Marc Gonzalez Signed-off-by: Olof Johansson diff --git a/arch/arm/mach-tango/Kconfig b/arch/arm/mach-tango/Kconfig index d6a3714..ebe15b9 100644 --- a/arch/arm/mach-tango/Kconfig +++ b/arch/arm/mach-tango/Kconfig @@ -1,5 +1,6 @@ config ARCH_TANGO - bool "Sigma Designs Tango4 (SMP87xx)" if ARCH_MULTI_V7 + bool "Sigma Designs Tango4 (SMP87xx)" + depends on ARCH_MULTI_V7 # Cortex-A9 MPCore r3p0, PL310 r3p2 select ARCH_HAS_HOLES_MEMORYMODEL select ARM_ERRATA_754322 -- cgit v0.10.2 From c65cd255e4b7dd529b9f35f7e4b05fe154adbb5f Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Mon, 25 Jan 2016 20:42:44 +0900 Subject: ARM: realview: use "depends on" instead of "if" after prompt This platform recently moved to multi-platform, so missed the global fixup by commit e32465429490 ("ARM: use "depends on" for SoC configs instead of "if" after prompt"). Fix it now. Signed-off-by: Masahiro Yamada Signed-off-by: Olof Johansson diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig index def40a0..70ab4a2 100644 --- a/arch/arm/mach-realview/Kconfig +++ b/arch/arm/mach-realview/Kconfig @@ -1,5 +1,6 @@ menuconfig ARCH_REALVIEW - bool "ARM Ltd. RealView family" if ARCH_MULTI_V5 || ARCH_MULTI_V6 || ARCH_MULTI_V7 + bool "ARM Ltd. RealView family" + depends on ARCH_MULTI_V5 || ARCH_MULTI_V6 || ARCH_MULTI_V7 select ARM_AMBA select ARM_TIMER_SP804 select COMMON_CLK_VERSATILE -- cgit v0.10.2 From 43acf83166eb85082e03b25c9ccd4851e7203ea1 Mon Sep 17 00:00:00 2001 From: Jon Hunter Date: Mon, 25 Jan 2016 20:25:55 +0000 Subject: ARM64: tegra: Add chosen node for tegra132 norrin The NVIDIA bootloader, nvtboot, expects the "chosen" node to be present in the device-tree blob and if it is not then it fails to boot the kernel. Add the chosen node so we can boot the kernel on Tegra132 Norrin with the nvtboot bootloader. Signed-off-by: Jon Hunter Acked-by: Thierry Reding Signed-off-by: Olof Johansson diff --git a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts index 7dfe1c0..62f33fc 100644 --- a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts +++ b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts @@ -12,6 +12,8 @@ rtc1 = "/rtc@0,7000e000"; }; + chosen { }; + memory { device_type = "memory"; reg = <0x0 0x80000000 0x0 0x80000000>; -- cgit v0.10.2 From 418d5516568b3fdbc4e7b53677dd78aed8514565 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 1 Feb 2016 14:18:57 +0100 Subject: ARM: nomadik: fix up SD/MMC DT settings The DTSI file for the Nomadik does not properly specify how the PL180 levelshifter is connected: the Nomadik actually needs all the five st,sig-dir-* flags set to properly control all lines out. Further this board supports full power cycling of the card, and since this variant has no hardware clock gating, it needs a ridiculously low frequency setting to keep up with the ever overflowing FIFO. The pin configuration set-up is a bit of a mystery, because of course these pins are a mix of inputs and outputs. However the reference implementation sets all pins to "output" with unspecified initial value, so let's do that here as well. Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij Acked-by: Ulf Hansson Signed-off-by: Olof Johansson diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi index d0c7438..27a333e 100644 --- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi +++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi @@ -127,22 +127,14 @@ }; mmcsd_default_mode: mmcsd_default { mmcsd_default_cfg1 { - /* MCCLK */ - pins = "GPIO8_B10"; - ste,output = <0>; - }; - mmcsd_default_cfg2 { - /* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */ - pins = "GPIO10_C11", "GPIO15_A12", - "GPIO16_C13", "GPIO23_D15"; - ste,output = <1>; - }; - mmcsd_default_cfg3 { - /* MCCMD, MCDAT3-0, MCMSFBCLK */ - pins = "GPIO9_A10", "GPIO11_B11", - "GPIO12_A11", "GPIO13_C12", - "GPIO14_B12", "GPIO24_C15"; - ste,input = <1>; + /* + * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 + * MCCMD, MCDAT3-0, MCMSFBCLK + */ + pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11", + "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12", + "GPIO16_C13", "GPIO23_D15", "GPIO24_C15"; + ste,output = <2>; }; }; }; @@ -802,10 +794,21 @@ clock-names = "mclk", "apb_pclk"; interrupt-parent = <&vica>; interrupts = <22>; - max-frequency = <48000000>; + max-frequency = <400000>; bus-width = <4>; cap-mmc-highspeed; cap-sd-highspeed; + full-pwr-cycle; + /* + * The STw4811 circuit used with the Nomadik strictly + * requires that all of these signal direction pins be + * routed and used for its 4-bit levelshifter. + */ + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-dat31; + st,sig-dir-cmd; + st,sig-pin-fbclk; pinctrl-names = "default"; pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>; vmmc-supply = <&vmmc_regulator>; -- cgit v0.10.2 From 381a65c21aa1fcf4f3fafe70027b79b303bdb71d Mon Sep 17 00:00:00 2001 From: Dinh Nguyen Date: Wed, 3 Feb 2016 11:03:06 -0600 Subject: ARM: multi_v7_defconfig: enable DW_WATCHDOG The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog. Enable CONFIG_DW_WATCHDOG for the driver to get built. Signed-off-by: Dinh Nguyen Tested-by: Kevin Hilman Signed-off-by: Olof Johansson diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index 314f6be..8e8b2ac 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -426,6 +426,7 @@ CONFIG_SUNXI_WATCHDOG=y CONFIG_IMX2_WDT=y CONFIG_TEGRA_WATCHDOG=m CONFIG_MESON_WATCHDOG=y +CONFIG_DW_WATCHDOG=y CONFIG_DIGICOLOR_WATCHDOG=y CONFIG_MFD_AS3711=y CONFIG_MFD_AS3722=y -- cgit v0.10.2