From b07682b6056eb6701f8cb86aa5800e6f2ea7919b Mon Sep 17 00:00:00 2001 From: Santosh Shilimkar Date: Sun, 13 Dec 2009 20:05:51 +0100 Subject: mfd: Rename twl4030* driver files to enable re-use The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030 for OMAP3. The common modules like RTC, Regulator creates opportunity to re-use the most of the code from twl4030. This patch renames few common drivers twl4030* files to twl* to enable the code re-use. Signed-off-by: Rajendra Nayak Signed-off-by: Balaji T K Signed-off-by: Santosh Shilimkar Acked-by: Kevin Hilman Signed-off-by: Samuel Ortiz diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index db9374b..e508904 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -19,7 +19,7 @@ #include #include #include -#include +#include #include #include #include diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 4cfb7b6..c90b0d0 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -20,7 +20,7 @@ #include #include #include -#include +#include #include #include #include diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index 3743173..995d4a2 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -24,7 +24,7 @@ #include #include #include -#include +#include #include #include diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 6ada802..231cb4e 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -29,7 +29,7 @@ #include #include -#include +#include #include #include diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 6f6c601..ef17cf1 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -24,7 +24,7 @@ #include #include #include -#include +#include #include #include #include diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 5b78a87..d192dd9 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -26,7 +26,7 @@ #include #include #include -#include +#include #include #include diff --git a/drivers/gpio/twl4030-gpio.c b/drivers/gpio/twl4030-gpio.c index 49384a7..a320d7b 100644 --- a/drivers/gpio/twl4030-gpio.c +++ b/drivers/gpio/twl4030-gpio.c @@ -34,7 +34,7 @@ #include #include -#include +#include /* diff --git a/drivers/input/keyboard/twl4030_keypad.c b/drivers/input/keyboard/twl4030_keypad.c index 9a2977c..1d1536a 100644 --- a/drivers/input/keyboard/twl4030_keypad.c +++ b/drivers/input/keyboard/twl4030_keypad.c @@ -31,7 +31,7 @@ #include #include #include -#include +#include /* diff --git a/drivers/input/misc/twl4030-pwrbutton.c b/drivers/input/misc/twl4030-pwrbutton.c index f5fc997..a73b889 100644 --- a/drivers/input/misc/twl4030-pwrbutton.c +++ b/drivers/input/misc/twl4030-pwrbutton.c @@ -27,7 +27,7 @@ #include #include #include -#include +#include #define PWR_PWRON_IRQ (1 << 0) diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 75638ca..f4d14b7 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -26,7 +26,7 @@ obj-$(CONFIG_MFD_WM8350_I2C) += wm8350-i2c.o obj-$(CONFIG_TPS65010) += tps65010.o obj-$(CONFIG_MENELAUS) += menelaus.o -obj-$(CONFIG_TWL4030_CORE) += twl4030-core.o twl4030-irq.o +obj-$(CONFIG_TWL4030_CORE) += twl-core.o twl4030-irq.o obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o obj-$(CONFIG_TWL4030_CODEC) += twl4030-codec.o diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c new file mode 100644 index 0000000..44714f5 --- /dev/null +++ b/drivers/mfd/twl-core.c @@ -0,0 +1,929 @@ +/* + * twl4030_core.c - driver for TWL4030/TPS659x0 PM and audio CODEC devices + * + * Copyright (C) 2005-2006 Texas Instruments, Inc. + * + * Modifications to defer interrupt handling to a kernel thread: + * Copyright (C) 2006 MontaVista Software, Inc. + * + * Based on tlv320aic23.c: + * Copyright (c) by Kai Svahn + * + * Code cleanup and modifications to IRQ handler. + * by syed khasim + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#include + +#include +#include + +#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) +#include +#endif + +/* + * The TWL4030 "Triton 2" is one of a family of a multi-function "Power + * Management and System Companion Device" chips originally designed for + * use in OMAP2 and OMAP 3 based systems. Its control interfaces use I2C, + * often at around 3 Mbit/sec, including for interrupt handling. + * + * This driver core provides genirq support for the interrupts emitted, + * by the various modules, and exports register access primitives. + * + * FIXME this driver currently requires use of the first interrupt line + * (and associated registers). + */ + +#define DRIVER_NAME "twl4030" + +#if defined(CONFIG_TWL4030_BCI_BATTERY) || \ + defined(CONFIG_TWL4030_BCI_BATTERY_MODULE) +#define twl_has_bci() true +#else +#define twl_has_bci() false +#endif + +#if defined(CONFIG_KEYBOARD_TWL4030) || defined(CONFIG_KEYBOARD_TWL4030_MODULE) +#define twl_has_keypad() true +#else +#define twl_has_keypad() false +#endif + +#if defined(CONFIG_GPIO_TWL4030) || defined(CONFIG_GPIO_TWL4030_MODULE) +#define twl_has_gpio() true +#else +#define twl_has_gpio() false +#endif + +#if defined(CONFIG_REGULATOR_TWL4030) \ + || defined(CONFIG_REGULATOR_TWL4030_MODULE) +#define twl_has_regulator() true +#else +#define twl_has_regulator() false +#endif + +#if defined(CONFIG_TWL4030_MADC) || defined(CONFIG_TWL4030_MADC_MODULE) +#define twl_has_madc() true +#else +#define twl_has_madc() false +#endif + +#ifdef CONFIG_TWL4030_POWER +#define twl_has_power() true +#else +#define twl_has_power() false +#endif + +#if defined(CONFIG_RTC_DRV_TWL4030) || defined(CONFIG_RTC_DRV_TWL4030_MODULE) +#define twl_has_rtc() true +#else +#define twl_has_rtc() false +#endif + +#if defined(CONFIG_TWL4030_USB) || defined(CONFIG_TWL4030_USB_MODULE) +#define twl_has_usb() true +#else +#define twl_has_usb() false +#endif + +#if defined(CONFIG_TWL4030_WATCHDOG) || \ + defined(CONFIG_TWL4030_WATCHDOG_MODULE) +#define twl_has_watchdog() true +#else +#define twl_has_watchdog() false +#endif + +#if defined(CONFIG_TWL4030_CODEC) || defined(CONFIG_TWL4030_CODEC_MODULE) +#define twl_has_codec() true +#else +#define twl_has_codec() false +#endif + +/* Triton Core internal information (BEGIN) */ + +/* Last - for index max*/ +#define TWL4030_MODULE_LAST TWL4030_MODULE_SECURED_REG + +#define TWL4030_NUM_SLAVES 4 + +#if defined(CONFIG_INPUT_TWL4030_PWRBUTTON) \ + || defined(CONFIG_INPUT_TWL4030_PWBUTTON_MODULE) +#define twl_has_pwrbutton() true +#else +#define twl_has_pwrbutton() false +#endif + +/* Base Address defns for twl4030_map[] */ + +/* subchip/slave 0 - USB ID */ +#define TWL4030_BASEADD_USB 0x0000 + +/* subchip/slave 1 - AUD ID */ +#define TWL4030_BASEADD_AUDIO_VOICE 0x0000 +#define TWL4030_BASEADD_GPIO 0x0098 +#define TWL4030_BASEADD_INTBR 0x0085 +#define TWL4030_BASEADD_PIH 0x0080 +#define TWL4030_BASEADD_TEST 0x004C + +/* subchip/slave 2 - AUX ID */ +#define TWL4030_BASEADD_INTERRUPTS 0x00B9 +#define TWL4030_BASEADD_LED 0x00EE +#define TWL4030_BASEADD_MADC 0x0000 +#define TWL4030_BASEADD_MAIN_CHARGE 0x0074 +#define TWL4030_BASEADD_PRECHARGE 0x00AA +#define TWL4030_BASEADD_PWM0 0x00F8 +#define TWL4030_BASEADD_PWM1 0x00FB +#define TWL4030_BASEADD_PWMA 0x00EF +#define TWL4030_BASEADD_PWMB 0x00F1 +#define TWL4030_BASEADD_KEYPAD 0x00D2 + +#define TWL5031_BASEADD_ACCESSORY 0x0074 /* Replaces Main Charge */ +#define TWL5031_BASEADD_INTERRUPTS 0x00B9 /* Different than TWL4030's + one */ + +/* subchip/slave 3 - POWER ID */ +#define TWL4030_BASEADD_BACKUP 0x0014 +#define TWL4030_BASEADD_INT 0x002E +#define TWL4030_BASEADD_PM_MASTER 0x0036 +#define TWL4030_BASEADD_PM_RECEIVER 0x005B +#define TWL4030_BASEADD_RTC 0x001C +#define TWL4030_BASEADD_SECURED_REG 0x0000 + +/* Triton Core internal information (END) */ + + +/* Few power values */ +#define R_CFG_BOOT 0x05 +#define R_PROTECT_KEY 0x0E + +/* access control values for R_PROTECT_KEY */ +#define KEY_UNLOCK1 0xce +#define KEY_UNLOCK2 0xec +#define KEY_LOCK 0x00 + +/* some fields in R_CFG_BOOT */ +#define HFCLK_FREQ_19p2_MHZ (1 << 0) +#define HFCLK_FREQ_26_MHZ (2 << 0) +#define HFCLK_FREQ_38p4_MHZ (3 << 0) +#define HIGH_PERF_SQ (1 << 3) +#define CK32K_LOWPWR_EN (1 << 7) + + +/* chip-specific feature flags, for i2c_device_id.driver_data */ +#define TWL4030_VAUX2 BIT(0) /* pre-5030 voltage ranges */ +#define TPS_SUBSET BIT(1) /* tps659[23]0 have fewer LDOs */ +#define TWL5031 BIT(2) /* twl5031 has different registers */ + +/*----------------------------------------------------------------------*/ + +/* is driver active, bound to a chip? */ +static bool inuse; + +/* Structure for each TWL4030 Slave */ +struct twl4030_client { + struct i2c_client *client; + u8 address; + + /* max numb of i2c_msg required is for read =2 */ + struct i2c_msg xfer_msg[2]; + + /* To lock access to xfer_msg */ + struct mutex xfer_lock; +}; + +static struct twl4030_client twl4030_modules[TWL4030_NUM_SLAVES]; + + +/* mapping the module id to slave id and base address */ +struct twl4030mapping { + unsigned char sid; /* Slave ID */ + unsigned char base; /* base address */ +}; + +static struct twl4030mapping twl4030_map[TWL4030_MODULE_LAST + 1] = { + /* + * NOTE: don't change this table without updating the + * defines for TWL4030_MODULE_* + * so they continue to match the order in this table. + */ + + { 0, TWL4030_BASEADD_USB }, + + { 1, TWL4030_BASEADD_AUDIO_VOICE }, + { 1, TWL4030_BASEADD_GPIO }, + { 1, TWL4030_BASEADD_INTBR }, + { 1, TWL4030_BASEADD_PIH }, + { 1, TWL4030_BASEADD_TEST }, + + { 2, TWL4030_BASEADD_KEYPAD }, + { 2, TWL4030_BASEADD_MADC }, + { 2, TWL4030_BASEADD_INTERRUPTS }, + { 2, TWL4030_BASEADD_LED }, + { 2, TWL4030_BASEADD_MAIN_CHARGE }, + { 2, TWL4030_BASEADD_PRECHARGE }, + { 2, TWL4030_BASEADD_PWM0 }, + { 2, TWL4030_BASEADD_PWM1 }, + { 2, TWL4030_BASEADD_PWMA }, + { 2, TWL4030_BASEADD_PWMB }, + { 2, TWL5031_BASEADD_ACCESSORY }, + { 2, TWL5031_BASEADD_INTERRUPTS }, + + { 3, TWL4030_BASEADD_BACKUP }, + { 3, TWL4030_BASEADD_INT }, + { 3, TWL4030_BASEADD_PM_MASTER }, + { 3, TWL4030_BASEADD_PM_RECEIVER }, + { 3, TWL4030_BASEADD_RTC }, + { 3, TWL4030_BASEADD_SECURED_REG }, +}; + +/*----------------------------------------------------------------------*/ + +/* Exported Functions */ + +/** + * twl4030_i2c_write - Writes a n bit register in TWL4030 + * @mod_no: module number + * @value: an array of num_bytes+1 containing data to write + * @reg: register address (just offset will do) + * @num_bytes: number of bytes to transfer + * + * IMPORTANT: for 'value' parameter: Allocate value num_bytes+1 and + * valid data starts at Offset 1. + * + * Returns the result of operation - 0 is success + */ +int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes) +{ + int ret; + int sid; + struct twl4030_client *twl; + struct i2c_msg *msg; + + if (unlikely(mod_no > TWL4030_MODULE_LAST)) { + pr_err("%s: invalid module number %d\n", DRIVER_NAME, mod_no); + return -EPERM; + } + sid = twl4030_map[mod_no].sid; + twl = &twl4030_modules[sid]; + + if (unlikely(!inuse)) { + pr_err("%s: client %d is not initialized\n", DRIVER_NAME, sid); + return -EPERM; + } + mutex_lock(&twl->xfer_lock); + /* + * [MSG1]: fill the register address data + * fill the data Tx buffer + */ + msg = &twl->xfer_msg[0]; + msg->addr = twl->address; + msg->len = num_bytes + 1; + msg->flags = 0; + msg->buf = value; + /* over write the first byte of buffer with the register address */ + *value = twl4030_map[mod_no].base + reg; + ret = i2c_transfer(twl->client->adapter, twl->xfer_msg, 1); + mutex_unlock(&twl->xfer_lock); + + /* i2c_transfer returns number of messages transferred */ + if (ret != 1) { + pr_err("%s: i2c_write failed to transfer all messages\n", + DRIVER_NAME); + if (ret < 0) + return ret; + else + return -EIO; + } else { + return 0; + } +} +EXPORT_SYMBOL(twl4030_i2c_write); + +/** + * twl4030_i2c_read - Reads a n bit register in TWL4030 + * @mod_no: module number + * @value: an array of num_bytes containing data to be read + * @reg: register address (just offset will do) + * @num_bytes: number of bytes to transfer + * + * Returns result of operation - num_bytes is success else failure. + */ +int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes) +{ + int ret; + u8 val; + int sid; + struct twl4030_client *twl; + struct i2c_msg *msg; + + if (unlikely(mod_no > TWL4030_MODULE_LAST)) { + pr_err("%s: invalid module number %d\n", DRIVER_NAME, mod_no); + return -EPERM; + } + sid = twl4030_map[mod_no].sid; + twl = &twl4030_modules[sid]; + + if (unlikely(!inuse)) { + pr_err("%s: client %d is not initialized\n", DRIVER_NAME, sid); + return -EPERM; + } + mutex_lock(&twl->xfer_lock); + /* [MSG1] fill the register address data */ + msg = &twl->xfer_msg[0]; + msg->addr = twl->address; + msg->len = 1; + msg->flags = 0; /* Read the register value */ + val = twl4030_map[mod_no].base + reg; + msg->buf = &val; + /* [MSG2] fill the data rx buffer */ + msg = &twl->xfer_msg[1]; + msg->addr = twl->address; + msg->flags = I2C_M_RD; /* Read the register value */ + msg->len = num_bytes; /* only n bytes */ + msg->buf = value; + ret = i2c_transfer(twl->client->adapter, twl->xfer_msg, 2); + mutex_unlock(&twl->xfer_lock); + + /* i2c_transfer returns number of messages transferred */ + if (ret != 2) { + pr_err("%s: i2c_read failed to transfer all messages\n", + DRIVER_NAME); + if (ret < 0) + return ret; + else + return -EIO; + } else { + return 0; + } +} +EXPORT_SYMBOL(twl4030_i2c_read); + +/** + * twl4030_i2c_write_u8 - Writes a 8 bit register in TWL4030 + * @mod_no: module number + * @value: the value to be written 8 bit + * @reg: register address (just offset will do) + * + * Returns result of operation - 0 is success + */ +int twl4030_i2c_write_u8(u8 mod_no, u8 value, u8 reg) +{ + + /* 2 bytes offset 1 contains the data offset 0 is used by i2c_write */ + u8 temp_buffer[2] = { 0 }; + /* offset 1 contains the data */ + temp_buffer[1] = value; + return twl4030_i2c_write(mod_no, temp_buffer, reg, 1); +} +EXPORT_SYMBOL(twl4030_i2c_write_u8); + +/** + * twl4030_i2c_read_u8 - Reads a 8 bit register from TWL4030 + * @mod_no: module number + * @value: the value read 8 bit + * @reg: register address (just offset will do) + * + * Returns result of operation - 0 is success + */ +int twl4030_i2c_read_u8(u8 mod_no, u8 *value, u8 reg) +{ + return twl4030_i2c_read(mod_no, value, reg, 1); +} +EXPORT_SYMBOL(twl4030_i2c_read_u8); + +/*----------------------------------------------------------------------*/ + +static struct device * +add_numbered_child(unsigned chip, const char *name, int num, + void *pdata, unsigned pdata_len, + bool can_wakeup, int irq0, int irq1) +{ + struct platform_device *pdev; + struct twl4030_client *twl = &twl4030_modules[chip]; + int status; + + pdev = platform_device_alloc(name, num); + if (!pdev) { + dev_dbg(&twl->client->dev, "can't alloc dev\n"); + status = -ENOMEM; + goto err; + } + + device_init_wakeup(&pdev->dev, can_wakeup); + pdev->dev.parent = &twl->client->dev; + + if (pdata) { + status = platform_device_add_data(pdev, pdata, pdata_len); + if (status < 0) { + dev_dbg(&pdev->dev, "can't add platform_data\n"); + goto err; + } + } + + if (irq0) { + struct resource r[2] = { + { .start = irq0, .flags = IORESOURCE_IRQ, }, + { .start = irq1, .flags = IORESOURCE_IRQ, }, + }; + + status = platform_device_add_resources(pdev, r, irq1 ? 2 : 1); + if (status < 0) { + dev_dbg(&pdev->dev, "can't add irqs\n"); + goto err; + } + } + + status = platform_device_add(pdev); + +err: + if (status < 0) { + platform_device_put(pdev); + dev_err(&twl->client->dev, "can't add %s dev\n", name); + return ERR_PTR(status); + } + return &pdev->dev; +} + +static inline struct device *add_child(unsigned chip, const char *name, + void *pdata, unsigned pdata_len, + bool can_wakeup, int irq0, int irq1) +{ + return add_numbered_child(chip, name, -1, pdata, pdata_len, + can_wakeup, irq0, irq1); +} + +static struct device * +add_regulator_linked(int num, struct regulator_init_data *pdata, + struct regulator_consumer_supply *consumers, + unsigned num_consumers) +{ + /* regulator framework demands init_data ... */ + if (!pdata) + return NULL; + + if (consumers) { + pdata->consumer_supplies = consumers; + pdata->num_consumer_supplies = num_consumers; + } + + /* NOTE: we currently ignore regulator IRQs, e.g. for short circuits */ + return add_numbered_child(3, "twl4030_reg", num, + pdata, sizeof(*pdata), false, 0, 0); +} + +static struct device * +add_regulator(int num, struct regulator_init_data *pdata) +{ + return add_regulator_linked(num, pdata, NULL, 0); +} + +/* + * NOTE: We know the first 8 IRQs after pdata->base_irq are + * for the PIH, and the next are for the PWR_INT SIH, since + * that's how twl_init_irq() sets things up. + */ + +static int +add_children(struct twl4030_platform_data *pdata, unsigned long features) +{ + struct device *child; + + if (twl_has_bci() && pdata->bci && + !(features & (TPS_SUBSET | TWL5031))) { + child = add_child(3, "twl4030_bci", + pdata->bci, sizeof(*pdata->bci), + false, + /* irq0 = CHG_PRES, irq1 = BCI */ + pdata->irq_base + 8 + 1, pdata->irq_base + 2); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_gpio() && pdata->gpio) { + child = add_child(1, "twl4030_gpio", + pdata->gpio, sizeof(*pdata->gpio), + false, pdata->irq_base + 0, 0); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_keypad() && pdata->keypad) { + child = add_child(2, "twl4030_keypad", + pdata->keypad, sizeof(*pdata->keypad), + true, pdata->irq_base + 1, 0); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_madc() && pdata->madc) { + child = add_child(2, "twl4030_madc", + pdata->madc, sizeof(*pdata->madc), + true, pdata->irq_base + 3, 0); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_rtc()) { + /* + * REVISIT platform_data here currently might expose the + * "msecure" line ... but for now we just expect board + * setup to tell the chip "it's always ok to SET_TIME". + * Eventually, Linux might become more aware of such + * HW security concerns, and "least privilege". + */ + child = add_child(3, "twl4030_rtc", + NULL, 0, + true, pdata->irq_base + 8 + 3, 0); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_usb() && pdata->usb) { + + static struct regulator_consumer_supply usb1v5 = { + .supply = "usb1v5", + }; + static struct regulator_consumer_supply usb1v8 = { + .supply = "usb1v8", + }; + static struct regulator_consumer_supply usb3v1 = { + .supply = "usb3v1", + }; + + /* First add the regulators so that they can be used by transceiver */ + if (twl_has_regulator()) { + /* this is a template that gets copied */ + struct regulator_init_data usb_fixed = { + .constraints.valid_modes_mask = + REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .constraints.valid_ops_mask = + REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }; + + child = add_regulator_linked(TWL4030_REG_VUSB1V5, + &usb_fixed, &usb1v5, 1); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator_linked(TWL4030_REG_VUSB1V8, + &usb_fixed, &usb1v8, 1); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator_linked(TWL4030_REG_VUSB3V1, + &usb_fixed, &usb3v1, 1); + if (IS_ERR(child)) + return PTR_ERR(child); + + } + + child = add_child(0, "twl4030_usb", + pdata->usb, sizeof(*pdata->usb), + true, + /* irq0 = USB_PRES, irq1 = USB */ + pdata->irq_base + 8 + 2, pdata->irq_base + 4); + + if (IS_ERR(child)) + return PTR_ERR(child); + + /* we need to connect regulators to this transceiver */ + if (twl_has_regulator() && child) { + usb1v5.dev = child; + usb1v8.dev = child; + usb3v1.dev = child; + } + } + + if (twl_has_watchdog()) { + child = add_child(0, "twl4030_wdt", NULL, 0, false, 0, 0); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_pwrbutton()) { + child = add_child(1, "twl4030_pwrbutton", + NULL, 0, true, pdata->irq_base + 8 + 0, 0); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_codec() && pdata->codec) { + child = add_child(1, "twl4030_codec", + pdata->codec, sizeof(*pdata->codec), + false, 0, 0); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + if (twl_has_regulator()) { + child = add_regulator(TWL4030_REG_VPLL1, pdata->vpll1); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VIO, pdata->vio); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VDD1, pdata->vdd1); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VDD2, pdata->vdd2); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VMMC1, pdata->vmmc1); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VDAC, pdata->vdac); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator((features & TWL4030_VAUX2) + ? TWL4030_REG_VAUX2_4030 + : TWL4030_REG_VAUX2, + pdata->vaux2); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VINTANA1, pdata->vintana1); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VINTANA2, pdata->vintana2); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VINTDIG, pdata->vintdig); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + /* maybe add LDOs that are omitted on cost-reduced parts */ + if (twl_has_regulator() && !(features & TPS_SUBSET)) { + child = add_regulator(TWL4030_REG_VPLL2, pdata->vpll2); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VMMC2, pdata->vmmc2); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VSIM, pdata->vsim); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VAUX1, pdata->vaux1); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VAUX3, pdata->vaux3); + if (IS_ERR(child)) + return PTR_ERR(child); + + child = add_regulator(TWL4030_REG_VAUX4, pdata->vaux4); + if (IS_ERR(child)) + return PTR_ERR(child); + } + + return 0; +} + +/*----------------------------------------------------------------------*/ + +/* + * These three functions initialize the on-chip clock framework, + * letting it generate the right frequencies for USB, MADC, and + * other purposes. + */ +static inline int __init protect_pm_master(void) +{ + int e = 0; + + e = twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, KEY_LOCK, + R_PROTECT_KEY); + return e; +} + +static inline int __init unprotect_pm_master(void) +{ + int e = 0; + + e |= twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, KEY_UNLOCK1, + R_PROTECT_KEY); + e |= twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, KEY_UNLOCK2, + R_PROTECT_KEY); + return e; +} + +static void clocks_init(struct device *dev, + struct twl4030_clock_init_data *clock) +{ + int e = 0; + struct clk *osc; + u32 rate; + u8 ctrl = HFCLK_FREQ_26_MHZ; + +#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) + if (cpu_is_omap2430()) + osc = clk_get(dev, "osc_ck"); + else + osc = clk_get(dev, "osc_sys_ck"); + + if (IS_ERR(osc)) { + printk(KERN_WARNING "Skipping twl4030 internal clock init and " + "using bootloader value (unknown osc rate)\n"); + return; + } + + rate = clk_get_rate(osc); + clk_put(osc); + +#else + /* REVISIT for non-OMAP systems, pass the clock rate from + * board init code, using platform_data. + */ + osc = ERR_PTR(-EIO); + + printk(KERN_WARNING "Skipping twl4030 internal clock init and " + "using bootloader value (unknown osc rate)\n"); + + return; +#endif + + switch (rate) { + case 19200000: + ctrl = HFCLK_FREQ_19p2_MHZ; + break; + case 26000000: + ctrl = HFCLK_FREQ_26_MHZ; + break; + case 38400000: + ctrl = HFCLK_FREQ_38p4_MHZ; + break; + } + + ctrl |= HIGH_PERF_SQ; + if (clock && clock->ck32k_lowpwr_enable) + ctrl |= CK32K_LOWPWR_EN; + + e |= unprotect_pm_master(); + /* effect->MADC+USB ck en */ + e |= twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, ctrl, R_CFG_BOOT); + e |= protect_pm_master(); + + if (e < 0) + pr_err("%s: clock init err [%d]\n", DRIVER_NAME, e); +} + +/*----------------------------------------------------------------------*/ + +int twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end); +int twl_exit_irq(void); +int twl_init_chip_irq(const char *chip); + +static int twl4030_remove(struct i2c_client *client) +{ + unsigned i; + int status; + + status = twl_exit_irq(); + if (status < 0) + return status; + + for (i = 0; i < TWL4030_NUM_SLAVES; i++) { + struct twl4030_client *twl = &twl4030_modules[i]; + + if (twl->client && twl->client != client) + i2c_unregister_device(twl->client); + twl4030_modules[i].client = NULL; + } + inuse = false; + return 0; +} + +/* NOTE: this driver only handles a single twl4030/tps659x0 chip */ +static int __init +twl4030_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + int status; + unsigned i; + struct twl4030_platform_data *pdata = client->dev.platform_data; + + if (!pdata) { + dev_dbg(&client->dev, "no platform data?\n"); + return -EINVAL; + } + + if (i2c_check_functionality(client->adapter, I2C_FUNC_I2C) == 0) { + dev_dbg(&client->dev, "can't talk I2C?\n"); + return -EIO; + } + + if (inuse) { + dev_dbg(&client->dev, "driver is already in use\n"); + return -EBUSY; + } + + for (i = 0; i < TWL4030_NUM_SLAVES; i++) { + struct twl4030_client *twl = &twl4030_modules[i]; + + twl->address = client->addr + i; + if (i == 0) + twl->client = client; + else { + twl->client = i2c_new_dummy(client->adapter, + twl->address); + if (!twl->client) { + dev_err(&client->dev, + "can't attach client %d\n", i); + status = -ENOMEM; + goto fail; + } + } + mutex_init(&twl->xfer_lock); + } + inuse = true; + + /* setup clock framework */ + clocks_init(&client->dev, pdata->clock); + + /* load power event scripts */ + if (twl_has_power() && pdata->power) + twl4030_power_init(pdata->power); + + /* Maybe init the T2 Interrupt subsystem */ + if (client->irq + && pdata->irq_base + && pdata->irq_end > pdata->irq_base) { + twl_init_chip_irq(id->name); + status = twl_init_irq(client->irq, pdata->irq_base, pdata->irq_end); + if (status < 0) + goto fail; + } + + status = add_children(pdata, id->driver_data); +fail: + if (status < 0) + twl4030_remove(client); + return status; +} + +static const struct i2c_device_id twl4030_ids[] = { + { "twl4030", TWL4030_VAUX2 }, /* "Triton 2" */ + { "twl5030", 0 }, /* T2 updated */ + { "twl5031", TWL5031 }, /* TWL5030 updated */ + { "tps65950", 0 }, /* catalog version of twl5030 */ + { "tps65930", TPS_SUBSET }, /* fewer LDOs and DACs; no charger */ + { "tps65920", TPS_SUBSET }, /* fewer LDOs; no codec or charger */ + { /* end of list */ }, +}; +MODULE_DEVICE_TABLE(i2c, twl4030_ids); + +/* One Client Driver , 4 Clients */ +static struct i2c_driver twl4030_driver = { + .driver.name = DRIVER_NAME, + .id_table = twl4030_ids, + .probe = twl4030_probe, + .remove = twl4030_remove, +}; + +static int __init twl4030_init(void) +{ + return i2c_add_driver(&twl4030_driver); +} +subsys_initcall(twl4030_init); + +static void __exit twl4030_exit(void) +{ + i2c_del_driver(&twl4030_driver); +} +module_exit(twl4030_exit); + +MODULE_AUTHOR("Texas Instruments, Inc."); +MODULE_DESCRIPTION("I2C Core interface for TWL4030"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mfd/twl4030-core.c b/drivers/mfd/twl4030-core.c deleted file mode 100644 index 7c2ec0a..0000000 --- a/drivers/mfd/twl4030-core.c +++ /dev/null @@ -1,929 +0,0 @@ -/* - * twl4030_core.c - driver for TWL4030/TPS659x0 PM and audio CODEC devices - * - * Copyright (C) 2005-2006 Texas Instruments, Inc. - * - * Modifications to defer interrupt handling to a kernel thread: - * Copyright (C) 2006 MontaVista Software, Inc. - * - * Based on tlv320aic23.c: - * Copyright (c) by Kai Svahn - * - * Code cleanup and modifications to IRQ handler. - * by syed khasim - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include - -#include - -#include -#include - -#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) -#include -#endif - -/* - * The TWL4030 "Triton 2" is one of a family of a multi-function "Power - * Management and System Companion Device" chips originally designed for - * use in OMAP2 and OMAP 3 based systems. Its control interfaces use I2C, - * often at around 3 Mbit/sec, including for interrupt handling. - * - * This driver core provides genirq support for the interrupts emitted, - * by the various modules, and exports register access primitives. - * - * FIXME this driver currently requires use of the first interrupt line - * (and associated registers). - */ - -#define DRIVER_NAME "twl4030" - -#if defined(CONFIG_TWL4030_BCI_BATTERY) || \ - defined(CONFIG_TWL4030_BCI_BATTERY_MODULE) -#define twl_has_bci() true -#else -#define twl_has_bci() false -#endif - -#if defined(CONFIG_KEYBOARD_TWL4030) || defined(CONFIG_KEYBOARD_TWL4030_MODULE) -#define twl_has_keypad() true -#else -#define twl_has_keypad() false -#endif - -#if defined(CONFIG_GPIO_TWL4030) || defined(CONFIG_GPIO_TWL4030_MODULE) -#define twl_has_gpio() true -#else -#define twl_has_gpio() false -#endif - -#if defined(CONFIG_REGULATOR_TWL4030) \ - || defined(CONFIG_REGULATOR_TWL4030_MODULE) -#define twl_has_regulator() true -#else -#define twl_has_regulator() false -#endif - -#if defined(CONFIG_TWL4030_MADC) || defined(CONFIG_TWL4030_MADC_MODULE) -#define twl_has_madc() true -#else -#define twl_has_madc() false -#endif - -#ifdef CONFIG_TWL4030_POWER -#define twl_has_power() true -#else -#define twl_has_power() false -#endif - -#if defined(CONFIG_RTC_DRV_TWL4030) || defined(CONFIG_RTC_DRV_TWL4030_MODULE) -#define twl_has_rtc() true -#else -#define twl_has_rtc() false -#endif - -#if defined(CONFIG_TWL4030_USB) || defined(CONFIG_TWL4030_USB_MODULE) -#define twl_has_usb() true -#else -#define twl_has_usb() false -#endif - -#if defined(CONFIG_TWL4030_WATCHDOG) || \ - defined(CONFIG_TWL4030_WATCHDOG_MODULE) -#define twl_has_watchdog() true -#else -#define twl_has_watchdog() false -#endif - -#if defined(CONFIG_TWL4030_CODEC) || defined(CONFIG_TWL4030_CODEC_MODULE) -#define twl_has_codec() true -#else -#define twl_has_codec() false -#endif - -/* Triton Core internal information (BEGIN) */ - -/* Last - for index max*/ -#define TWL4030_MODULE_LAST TWL4030_MODULE_SECURED_REG - -#define TWL4030_NUM_SLAVES 4 - -#if defined(CONFIG_INPUT_TWL4030_PWRBUTTON) \ - || defined(CONFIG_INPUT_TWL4030_PWBUTTON_MODULE) -#define twl_has_pwrbutton() true -#else -#define twl_has_pwrbutton() false -#endif - -/* Base Address defns for twl4030_map[] */ - -/* subchip/slave 0 - USB ID */ -#define TWL4030_BASEADD_USB 0x0000 - -/* subchip/slave 1 - AUD ID */ -#define TWL4030_BASEADD_AUDIO_VOICE 0x0000 -#define TWL4030_BASEADD_GPIO 0x0098 -#define TWL4030_BASEADD_INTBR 0x0085 -#define TWL4030_BASEADD_PIH 0x0080 -#define TWL4030_BASEADD_TEST 0x004C - -/* subchip/slave 2 - AUX ID */ -#define TWL4030_BASEADD_INTERRUPTS 0x00B9 -#define TWL4030_BASEADD_LED 0x00EE -#define TWL4030_BASEADD_MADC 0x0000 -#define TWL4030_BASEADD_MAIN_CHARGE 0x0074 -#define TWL4030_BASEADD_PRECHARGE 0x00AA -#define TWL4030_BASEADD_PWM0 0x00F8 -#define TWL4030_BASEADD_PWM1 0x00FB -#define TWL4030_BASEADD_PWMA 0x00EF -#define TWL4030_BASEADD_PWMB 0x00F1 -#define TWL4030_BASEADD_KEYPAD 0x00D2 - -#define TWL5031_BASEADD_ACCESSORY 0x0074 /* Replaces Main Charge */ -#define TWL5031_BASEADD_INTERRUPTS 0x00B9 /* Different than TWL4030's - one */ - -/* subchip/slave 3 - POWER ID */ -#define TWL4030_BASEADD_BACKUP 0x0014 -#define TWL4030_BASEADD_INT 0x002E -#define TWL4030_BASEADD_PM_MASTER 0x0036 -#define TWL4030_BASEADD_PM_RECEIVER 0x005B -#define TWL4030_BASEADD_RTC 0x001C -#define TWL4030_BASEADD_SECURED_REG 0x0000 - -/* Triton Core internal information (END) */ - - -/* Few power values */ -#define R_CFG_BOOT 0x05 -#define R_PROTECT_KEY 0x0E - -/* access control values for R_PROTECT_KEY */ -#define KEY_UNLOCK1 0xce -#define KEY_UNLOCK2 0xec -#define KEY_LOCK 0x00 - -/* some fields in R_CFG_BOOT */ -#define HFCLK_FREQ_19p2_MHZ (1 << 0) -#define HFCLK_FREQ_26_MHZ (2 << 0) -#define HFCLK_FREQ_38p4_MHZ (3 << 0) -#define HIGH_PERF_SQ (1 << 3) -#define CK32K_LOWPWR_EN (1 << 7) - - -/* chip-specific feature flags, for i2c_device_id.driver_data */ -#define TWL4030_VAUX2 BIT(0) /* pre-5030 voltage ranges */ -#define TPS_SUBSET BIT(1) /* tps659[23]0 have fewer LDOs */ -#define TWL5031 BIT(2) /* twl5031 has different registers */ - -/*----------------------------------------------------------------------*/ - -/* is driver active, bound to a chip? */ -static bool inuse; - -/* Structure for each TWL4030 Slave */ -struct twl4030_client { - struct i2c_client *client; - u8 address; - - /* max numb of i2c_msg required is for read =2 */ - struct i2c_msg xfer_msg[2]; - - /* To lock access to xfer_msg */ - struct mutex xfer_lock; -}; - -static struct twl4030_client twl4030_modules[TWL4030_NUM_SLAVES]; - - -/* mapping the module id to slave id and base address */ -struct twl4030mapping { - unsigned char sid; /* Slave ID */ - unsigned char base; /* base address */ -}; - -static struct twl4030mapping twl4030_map[TWL4030_MODULE_LAST + 1] = { - /* - * NOTE: don't change this table without updating the - * defines for TWL4030_MODULE_* - * so they continue to match the order in this table. - */ - - { 0, TWL4030_BASEADD_USB }, - - { 1, TWL4030_BASEADD_AUDIO_VOICE }, - { 1, TWL4030_BASEADD_GPIO }, - { 1, TWL4030_BASEADD_INTBR }, - { 1, TWL4030_BASEADD_PIH }, - { 1, TWL4030_BASEADD_TEST }, - - { 2, TWL4030_BASEADD_KEYPAD }, - { 2, TWL4030_BASEADD_MADC }, - { 2, TWL4030_BASEADD_INTERRUPTS }, - { 2, TWL4030_BASEADD_LED }, - { 2, TWL4030_BASEADD_MAIN_CHARGE }, - { 2, TWL4030_BASEADD_PRECHARGE }, - { 2, TWL4030_BASEADD_PWM0 }, - { 2, TWL4030_BASEADD_PWM1 }, - { 2, TWL4030_BASEADD_PWMA }, - { 2, TWL4030_BASEADD_PWMB }, - { 2, TWL5031_BASEADD_ACCESSORY }, - { 2, TWL5031_BASEADD_INTERRUPTS }, - - { 3, TWL4030_BASEADD_BACKUP }, - { 3, TWL4030_BASEADD_INT }, - { 3, TWL4030_BASEADD_PM_MASTER }, - { 3, TWL4030_BASEADD_PM_RECEIVER }, - { 3, TWL4030_BASEADD_RTC }, - { 3, TWL4030_BASEADD_SECURED_REG }, -}; - -/*----------------------------------------------------------------------*/ - -/* Exported Functions */ - -/** - * twl4030_i2c_write - Writes a n bit register in TWL4030 - * @mod_no: module number - * @value: an array of num_bytes+1 containing data to write - * @reg: register address (just offset will do) - * @num_bytes: number of bytes to transfer - * - * IMPORTANT: for 'value' parameter: Allocate value num_bytes+1 and - * valid data starts at Offset 1. - * - * Returns the result of operation - 0 is success - */ -int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes) -{ - int ret; - int sid; - struct twl4030_client *twl; - struct i2c_msg *msg; - - if (unlikely(mod_no > TWL4030_MODULE_LAST)) { - pr_err("%s: invalid module number %d\n", DRIVER_NAME, mod_no); - return -EPERM; - } - sid = twl4030_map[mod_no].sid; - twl = &twl4030_modules[sid]; - - if (unlikely(!inuse)) { - pr_err("%s: client %d is not initialized\n", DRIVER_NAME, sid); - return -EPERM; - } - mutex_lock(&twl->xfer_lock); - /* - * [MSG1]: fill the register address data - * fill the data Tx buffer - */ - msg = &twl->xfer_msg[0]; - msg->addr = twl->address; - msg->len = num_bytes + 1; - msg->flags = 0; - msg->buf = value; - /* over write the first byte of buffer with the register address */ - *value = twl4030_map[mod_no].base + reg; - ret = i2c_transfer(twl->client->adapter, twl->xfer_msg, 1); - mutex_unlock(&twl->xfer_lock); - - /* i2c_transfer returns number of messages transferred */ - if (ret != 1) { - pr_err("%s: i2c_write failed to transfer all messages\n", - DRIVER_NAME); - if (ret < 0) - return ret; - else - return -EIO; - } else { - return 0; - } -} -EXPORT_SYMBOL(twl4030_i2c_write); - -/** - * twl4030_i2c_read - Reads a n bit register in TWL4030 - * @mod_no: module number - * @value: an array of num_bytes containing data to be read - * @reg: register address (just offset will do) - * @num_bytes: number of bytes to transfer - * - * Returns result of operation - num_bytes is success else failure. - */ -int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes) -{ - int ret; - u8 val; - int sid; - struct twl4030_client *twl; - struct i2c_msg *msg; - - if (unlikely(mod_no > TWL4030_MODULE_LAST)) { - pr_err("%s: invalid module number %d\n", DRIVER_NAME, mod_no); - return -EPERM; - } - sid = twl4030_map[mod_no].sid; - twl = &twl4030_modules[sid]; - - if (unlikely(!inuse)) { - pr_err("%s: client %d is not initialized\n", DRIVER_NAME, sid); - return -EPERM; - } - mutex_lock(&twl->xfer_lock); - /* [MSG1] fill the register address data */ - msg = &twl->xfer_msg[0]; - msg->addr = twl->address; - msg->len = 1; - msg->flags = 0; /* Read the register value */ - val = twl4030_map[mod_no].base + reg; - msg->buf = &val; - /* [MSG2] fill the data rx buffer */ - msg = &twl->xfer_msg[1]; - msg->addr = twl->address; - msg->flags = I2C_M_RD; /* Read the register value */ - msg->len = num_bytes; /* only n bytes */ - msg->buf = value; - ret = i2c_transfer(twl->client->adapter, twl->xfer_msg, 2); - mutex_unlock(&twl->xfer_lock); - - /* i2c_transfer returns number of messages transferred */ - if (ret != 2) { - pr_err("%s: i2c_read failed to transfer all messages\n", - DRIVER_NAME); - if (ret < 0) - return ret; - else - return -EIO; - } else { - return 0; - } -} -EXPORT_SYMBOL(twl4030_i2c_read); - -/** - * twl4030_i2c_write_u8 - Writes a 8 bit register in TWL4030 - * @mod_no: module number - * @value: the value to be written 8 bit - * @reg: register address (just offset will do) - * - * Returns result of operation - 0 is success - */ -int twl4030_i2c_write_u8(u8 mod_no, u8 value, u8 reg) -{ - - /* 2 bytes offset 1 contains the data offset 0 is used by i2c_write */ - u8 temp_buffer[2] = { 0 }; - /* offset 1 contains the data */ - temp_buffer[1] = value; - return twl4030_i2c_write(mod_no, temp_buffer, reg, 1); -} -EXPORT_SYMBOL(twl4030_i2c_write_u8); - -/** - * twl4030_i2c_read_u8 - Reads a 8 bit register from TWL4030 - * @mod_no: module number - * @value: the value read 8 bit - * @reg: register address (just offset will do) - * - * Returns result of operation - 0 is success - */ -int twl4030_i2c_read_u8(u8 mod_no, u8 *value, u8 reg) -{ - return twl4030_i2c_read(mod_no, value, reg, 1); -} -EXPORT_SYMBOL(twl4030_i2c_read_u8); - -/*----------------------------------------------------------------------*/ - -static struct device * -add_numbered_child(unsigned chip, const char *name, int num, - void *pdata, unsigned pdata_len, - bool can_wakeup, int irq0, int irq1) -{ - struct platform_device *pdev; - struct twl4030_client *twl = &twl4030_modules[chip]; - int status; - - pdev = platform_device_alloc(name, num); - if (!pdev) { - dev_dbg(&twl->client->dev, "can't alloc dev\n"); - status = -ENOMEM; - goto err; - } - - device_init_wakeup(&pdev->dev, can_wakeup); - pdev->dev.parent = &twl->client->dev; - - if (pdata) { - status = platform_device_add_data(pdev, pdata, pdata_len); - if (status < 0) { - dev_dbg(&pdev->dev, "can't add platform_data\n"); - goto err; - } - } - - if (irq0) { - struct resource r[2] = { - { .start = irq0, .flags = IORESOURCE_IRQ, }, - { .start = irq1, .flags = IORESOURCE_IRQ, }, - }; - - status = platform_device_add_resources(pdev, r, irq1 ? 2 : 1); - if (status < 0) { - dev_dbg(&pdev->dev, "can't add irqs\n"); - goto err; - } - } - - status = platform_device_add(pdev); - -err: - if (status < 0) { - platform_device_put(pdev); - dev_err(&twl->client->dev, "can't add %s dev\n", name); - return ERR_PTR(status); - } - return &pdev->dev; -} - -static inline struct device *add_child(unsigned chip, const char *name, - void *pdata, unsigned pdata_len, - bool can_wakeup, int irq0, int irq1) -{ - return add_numbered_child(chip, name, -1, pdata, pdata_len, - can_wakeup, irq0, irq1); -} - -static struct device * -add_regulator_linked(int num, struct regulator_init_data *pdata, - struct regulator_consumer_supply *consumers, - unsigned num_consumers) -{ - /* regulator framework demands init_data ... */ - if (!pdata) - return NULL; - - if (consumers) { - pdata->consumer_supplies = consumers; - pdata->num_consumer_supplies = num_consumers; - } - - /* NOTE: we currently ignore regulator IRQs, e.g. for short circuits */ - return add_numbered_child(3, "twl4030_reg", num, - pdata, sizeof(*pdata), false, 0, 0); -} - -static struct device * -add_regulator(int num, struct regulator_init_data *pdata) -{ - return add_regulator_linked(num, pdata, NULL, 0); -} - -/* - * NOTE: We know the first 8 IRQs after pdata->base_irq are - * for the PIH, and the next are for the PWR_INT SIH, since - * that's how twl_init_irq() sets things up. - */ - -static int -add_children(struct twl4030_platform_data *pdata, unsigned long features) -{ - struct device *child; - - if (twl_has_bci() && pdata->bci && - !(features & (TPS_SUBSET | TWL5031))) { - child = add_child(3, "twl4030_bci", - pdata->bci, sizeof(*pdata->bci), - false, - /* irq0 = CHG_PRES, irq1 = BCI */ - pdata->irq_base + 8 + 1, pdata->irq_base + 2); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_gpio() && pdata->gpio) { - child = add_child(1, "twl4030_gpio", - pdata->gpio, sizeof(*pdata->gpio), - false, pdata->irq_base + 0, 0); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_keypad() && pdata->keypad) { - child = add_child(2, "twl4030_keypad", - pdata->keypad, sizeof(*pdata->keypad), - true, pdata->irq_base + 1, 0); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_madc() && pdata->madc) { - child = add_child(2, "twl4030_madc", - pdata->madc, sizeof(*pdata->madc), - true, pdata->irq_base + 3, 0); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_rtc()) { - /* - * REVISIT platform_data here currently might expose the - * "msecure" line ... but for now we just expect board - * setup to tell the chip "it's always ok to SET_TIME". - * Eventually, Linux might become more aware of such - * HW security concerns, and "least privilege". - */ - child = add_child(3, "twl4030_rtc", - NULL, 0, - true, pdata->irq_base + 8 + 3, 0); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_usb() && pdata->usb) { - - static struct regulator_consumer_supply usb1v5 = { - .supply = "usb1v5", - }; - static struct regulator_consumer_supply usb1v8 = { - .supply = "usb1v8", - }; - static struct regulator_consumer_supply usb3v1 = { - .supply = "usb3v1", - }; - - /* First add the regulators so that they can be used by transceiver */ - if (twl_has_regulator()) { - /* this is a template that gets copied */ - struct regulator_init_data usb_fixed = { - .constraints.valid_modes_mask = - REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .constraints.valid_ops_mask = - REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }; - - child = add_regulator_linked(TWL4030_REG_VUSB1V5, - &usb_fixed, &usb1v5, 1); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator_linked(TWL4030_REG_VUSB1V8, - &usb_fixed, &usb1v8, 1); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator_linked(TWL4030_REG_VUSB3V1, - &usb_fixed, &usb3v1, 1); - if (IS_ERR(child)) - return PTR_ERR(child); - - } - - child = add_child(0, "twl4030_usb", - pdata->usb, sizeof(*pdata->usb), - true, - /* irq0 = USB_PRES, irq1 = USB */ - pdata->irq_base + 8 + 2, pdata->irq_base + 4); - - if (IS_ERR(child)) - return PTR_ERR(child); - - /* we need to connect regulators to this transceiver */ - if (twl_has_regulator() && child) { - usb1v5.dev = child; - usb1v8.dev = child; - usb3v1.dev = child; - } - } - - if (twl_has_watchdog()) { - child = add_child(0, "twl4030_wdt", NULL, 0, false, 0, 0); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_pwrbutton()) { - child = add_child(1, "twl4030_pwrbutton", - NULL, 0, true, pdata->irq_base + 8 + 0, 0); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_codec() && pdata->codec) { - child = add_child(1, "twl4030_codec", - pdata->codec, sizeof(*pdata->codec), - false, 0, 0); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - if (twl_has_regulator()) { - child = add_regulator(TWL4030_REG_VPLL1, pdata->vpll1); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VIO, pdata->vio); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VDD1, pdata->vdd1); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VDD2, pdata->vdd2); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VMMC1, pdata->vmmc1); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VDAC, pdata->vdac); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator((features & TWL4030_VAUX2) - ? TWL4030_REG_VAUX2_4030 - : TWL4030_REG_VAUX2, - pdata->vaux2); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VINTANA1, pdata->vintana1); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VINTANA2, pdata->vintana2); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VINTDIG, pdata->vintdig); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - /* maybe add LDOs that are omitted on cost-reduced parts */ - if (twl_has_regulator() && !(features & TPS_SUBSET)) { - child = add_regulator(TWL4030_REG_VPLL2, pdata->vpll2); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VMMC2, pdata->vmmc2); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VSIM, pdata->vsim); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VAUX1, pdata->vaux1); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VAUX3, pdata->vaux3); - if (IS_ERR(child)) - return PTR_ERR(child); - - child = add_regulator(TWL4030_REG_VAUX4, pdata->vaux4); - if (IS_ERR(child)) - return PTR_ERR(child); - } - - return 0; -} - -/*----------------------------------------------------------------------*/ - -/* - * These three functions initialize the on-chip clock framework, - * letting it generate the right frequencies for USB, MADC, and - * other purposes. - */ -static inline int __init protect_pm_master(void) -{ - int e = 0; - - e = twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, KEY_LOCK, - R_PROTECT_KEY); - return e; -} - -static inline int __init unprotect_pm_master(void) -{ - int e = 0; - - e |= twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, KEY_UNLOCK1, - R_PROTECT_KEY); - e |= twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, KEY_UNLOCK2, - R_PROTECT_KEY); - return e; -} - -static void clocks_init(struct device *dev, - struct twl4030_clock_init_data *clock) -{ - int e = 0; - struct clk *osc; - u32 rate; - u8 ctrl = HFCLK_FREQ_26_MHZ; - -#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) - if (cpu_is_omap2430()) - osc = clk_get(dev, "osc_ck"); - else - osc = clk_get(dev, "osc_sys_ck"); - - if (IS_ERR(osc)) { - printk(KERN_WARNING "Skipping twl4030 internal clock init and " - "using bootloader value (unknown osc rate)\n"); - return; - } - - rate = clk_get_rate(osc); - clk_put(osc); - -#else - /* REVISIT for non-OMAP systems, pass the clock rate from - * board init code, using platform_data. - */ - osc = ERR_PTR(-EIO); - - printk(KERN_WARNING "Skipping twl4030 internal clock init and " - "using bootloader value (unknown osc rate)\n"); - - return; -#endif - - switch (rate) { - case 19200000: - ctrl = HFCLK_FREQ_19p2_MHZ; - break; - case 26000000: - ctrl = HFCLK_FREQ_26_MHZ; - break; - case 38400000: - ctrl = HFCLK_FREQ_38p4_MHZ; - break; - } - - ctrl |= HIGH_PERF_SQ; - if (clock && clock->ck32k_lowpwr_enable) - ctrl |= CK32K_LOWPWR_EN; - - e |= unprotect_pm_master(); - /* effect->MADC+USB ck en */ - e |= twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, ctrl, R_CFG_BOOT); - e |= protect_pm_master(); - - if (e < 0) - pr_err("%s: clock init err [%d]\n", DRIVER_NAME, e); -} - -/*----------------------------------------------------------------------*/ - -int twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end); -int twl_exit_irq(void); -int twl_init_chip_irq(const char *chip); - -static int twl4030_remove(struct i2c_client *client) -{ - unsigned i; - int status; - - status = twl_exit_irq(); - if (status < 0) - return status; - - for (i = 0; i < TWL4030_NUM_SLAVES; i++) { - struct twl4030_client *twl = &twl4030_modules[i]; - - if (twl->client && twl->client != client) - i2c_unregister_device(twl->client); - twl4030_modules[i].client = NULL; - } - inuse = false; - return 0; -} - -/* NOTE: this driver only handles a single twl4030/tps659x0 chip */ -static int __init -twl4030_probe(struct i2c_client *client, const struct i2c_device_id *id) -{ - int status; - unsigned i; - struct twl4030_platform_data *pdata = client->dev.platform_data; - - if (!pdata) { - dev_dbg(&client->dev, "no platform data?\n"); - return -EINVAL; - } - - if (i2c_check_functionality(client->adapter, I2C_FUNC_I2C) == 0) { - dev_dbg(&client->dev, "can't talk I2C?\n"); - return -EIO; - } - - if (inuse) { - dev_dbg(&client->dev, "driver is already in use\n"); - return -EBUSY; - } - - for (i = 0; i < TWL4030_NUM_SLAVES; i++) { - struct twl4030_client *twl = &twl4030_modules[i]; - - twl->address = client->addr + i; - if (i == 0) - twl->client = client; - else { - twl->client = i2c_new_dummy(client->adapter, - twl->address); - if (!twl->client) { - dev_err(&client->dev, - "can't attach client %d\n", i); - status = -ENOMEM; - goto fail; - } - } - mutex_init(&twl->xfer_lock); - } - inuse = true; - - /* setup clock framework */ - clocks_init(&client->dev, pdata->clock); - - /* load power event scripts */ - if (twl_has_power() && pdata->power) - twl4030_power_init(pdata->power); - - /* Maybe init the T2 Interrupt subsystem */ - if (client->irq - && pdata->irq_base - && pdata->irq_end > pdata->irq_base) { - twl_init_chip_irq(id->name); - status = twl_init_irq(client->irq, pdata->irq_base, pdata->irq_end); - if (status < 0) - goto fail; - } - - status = add_children(pdata, id->driver_data); -fail: - if (status < 0) - twl4030_remove(client); - return status; -} - -static const struct i2c_device_id twl4030_ids[] = { - { "twl4030", TWL4030_VAUX2 }, /* "Triton 2" */ - { "twl5030", 0 }, /* T2 updated */ - { "twl5031", TWL5031 }, /* TWL5030 updated */ - { "tps65950", 0 }, /* catalog version of twl5030 */ - { "tps65930", TPS_SUBSET }, /* fewer LDOs and DACs; no charger */ - { "tps65920", TPS_SUBSET }, /* fewer LDOs; no codec or charger */ - { /* end of list */ }, -}; -MODULE_DEVICE_TABLE(i2c, twl4030_ids); - -/* One Client Driver , 4 Clients */ -static struct i2c_driver twl4030_driver = { - .driver.name = DRIVER_NAME, - .id_table = twl4030_ids, - .probe = twl4030_probe, - .remove = twl4030_remove, -}; - -static int __init twl4030_init(void) -{ - return i2c_add_driver(&twl4030_driver); -} -subsys_initcall(twl4030_init); - -static void __exit twl4030_exit(void) -{ - i2c_del_driver(&twl4030_driver); -} -module_exit(twl4030_exit); - -MODULE_AUTHOR("Texas Instruments, Inc."); -MODULE_DESCRIPTION("I2C Core interface for TWL4030"); -MODULE_LICENSE("GPL"); diff --git a/drivers/mfd/twl4030-irq.c b/drivers/mfd/twl4030-irq.c index 3f7e93c..c4528db 100644 --- a/drivers/mfd/twl4030-irq.c +++ b/drivers/mfd/twl4030-irq.c @@ -32,7 +32,7 @@ #include #include -#include +#include /* diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index 3048f18..424b255 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -26,7 +26,7 @@ #include #include -#include +#include #include #include diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 4257a86..9ae3cc4 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -11,7 +11,7 @@ obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o obj-$(CONFIG_REGULATOR_BQ24022) += bq24022.o obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o -obj-$(CONFIG_REGULATOR_TWL4030) += twl4030-regulator.o +obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o obj-$(CONFIG_REGULATOR_WM831X) += wm831x-ldo.o diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c new file mode 100644 index 0000000..c8a6e58 --- /dev/null +++ b/drivers/regulator/twl-regulator.c @@ -0,0 +1,500 @@ +/* + * twl4030-regulator.c -- support regulators in twl4030 family chips + * + * Copyright (C) 2008 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include + + +/* + * The TWL4030/TW5030/TPS659x0 family chips include power management, a + * USB OTG transceiver, an RTC, ADC, PWM, and lots more. Some versions + * include an audio codec, battery charger, and more voltage regulators. + * These chips are often used in OMAP-based systems. + * + * This driver implements software-based resource control for various + * voltage regulators. This is usually augmented with state machine + * based control. + */ + +struct twlreg_info { + /* start of regulator's PM_RECEIVER control register bank */ + u8 base; + + /* twl4030 resource ID, for resource control state machine */ + u8 id; + + /* voltage in mV = table[VSEL]; table_len must be a power-of-two */ + u8 table_len; + const u16 *table; + + /* chip constraints on regulator behavior */ + u16 min_mV; + + /* used by regulator core */ + struct regulator_desc desc; +}; + + +/* LDO control registers ... offset is from the base of its register bank. + * The first three registers of all power resource banks help hardware to + * manage the various resource groups. + */ +#define VREG_GRP 0 +#define VREG_TYPE 1 +#define VREG_REMAP 2 +#define VREG_DEDICATED 3 /* LDO control */ + + +static inline int +twl4030reg_read(struct twlreg_info *info, unsigned offset) +{ + u8 value; + int status; + + status = twl4030_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, + &value, info->base + offset); + return (status < 0) ? status : value; +} + +static inline int +twl4030reg_write(struct twlreg_info *info, unsigned offset, u8 value) +{ + return twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, + value, info->base + offset); +} + +/*----------------------------------------------------------------------*/ + +/* generic power resource operations, which work on all regulators */ + +static int twl4030reg_grp(struct regulator_dev *rdev) +{ + return twl4030reg_read(rdev_get_drvdata(rdev), VREG_GRP); +} + +/* + * Enable/disable regulators by joining/leaving the P1 (processor) group. + * We assume nobody else is updating the DEV_GRP registers. + */ + +#define P3_GRP BIT(7) /* "peripherals" */ +#define P2_GRP BIT(6) /* secondary processor, modem, etc */ +#define P1_GRP BIT(5) /* CPU/Linux */ + +static int twl4030reg_is_enabled(struct regulator_dev *rdev) +{ + int state = twl4030reg_grp(rdev); + + if (state < 0) + return state; + + return (state & P1_GRP) != 0; +} + +static int twl4030reg_enable(struct regulator_dev *rdev) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + int grp; + + grp = twl4030reg_read(info, VREG_GRP); + if (grp < 0) + return grp; + + grp |= P1_GRP; + return twl4030reg_write(info, VREG_GRP, grp); +} + +static int twl4030reg_disable(struct regulator_dev *rdev) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + int grp; + + grp = twl4030reg_read(info, VREG_GRP); + if (grp < 0) + return grp; + + grp &= ~P1_GRP; + return twl4030reg_write(info, VREG_GRP, grp); +} + +static int twl4030reg_get_status(struct regulator_dev *rdev) +{ + int state = twl4030reg_grp(rdev); + + if (state < 0) + return state; + state &= 0x0f; + + /* assume state != WARM_RESET; we'd not be running... */ + if (!state) + return REGULATOR_STATUS_OFF; + return (state & BIT(3)) + ? REGULATOR_STATUS_NORMAL + : REGULATOR_STATUS_STANDBY; +} + +static int twl4030reg_set_mode(struct regulator_dev *rdev, unsigned mode) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + unsigned message; + int status; + + /* We can only set the mode through state machine commands... */ + switch (mode) { + case REGULATOR_MODE_NORMAL: + message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_ACTIVE); + break; + case REGULATOR_MODE_STANDBY: + message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_SLEEP); + break; + default: + return -EINVAL; + } + + /* Ensure the resource is associated with some group */ + status = twl4030reg_grp(rdev); + if (status < 0) + return status; + if (!(status & (P3_GRP | P2_GRP | P1_GRP))) + return -EACCES; + + status = twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, + message >> 8, 0x15 /* PB_WORD_MSB */ ); + if (status >= 0) + return status; + + return twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, + message, 0x16 /* PB_WORD_LSB */ ); +} + +/*----------------------------------------------------------------------*/ + +/* + * Support for adjustable-voltage LDOs uses a four bit (or less) voltage + * select field in its control register. We use tables indexed by VSEL + * to record voltages in milliVolts. (Accuracy is about three percent.) + * + * Note that VSEL values for VAUX2 changed in twl5030 and newer silicon; + * currently handled by listing two slightly different VAUX2 regulators, + * only one of which will be configured. + * + * VSEL values documented as "TI cannot support these values" are flagged + * in these tables as UNSUP() values; we normally won't assign them. + * + * VAUX3 at 3V is incorrectly listed in some TI manuals as unsupported. + * TI are revising the twl5030/tps659x0 specs to support that 3.0V setting. + */ +#ifdef CONFIG_TWL4030_ALLOW_UNSUPPORTED +#define UNSUP_MASK 0x0000 +#else +#define UNSUP_MASK 0x8000 +#endif + +#define UNSUP(x) (UNSUP_MASK | (x)) +#define IS_UNSUP(x) (UNSUP_MASK & (x)) +#define LDO_MV(x) (~UNSUP_MASK & (x)) + + +static const u16 VAUX1_VSEL_table[] = { + UNSUP(1500), UNSUP(1800), 2500, 2800, + 3000, 3000, 3000, 3000, +}; +static const u16 VAUX2_4030_VSEL_table[] = { + UNSUP(1000), UNSUP(1000), UNSUP(1200), 1300, + 1500, 1800, UNSUP(1850), 2500, + UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), + UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), +}; +static const u16 VAUX2_VSEL_table[] = { + 1700, 1700, 1900, 1300, + 1500, 1800, 2000, 2500, + 2100, 2800, 2200, 2300, + 2400, 2400, 2400, 2400, +}; +static const u16 VAUX3_VSEL_table[] = { + 1500, 1800, 2500, 2800, + 3000, 3000, 3000, 3000, +}; +static const u16 VAUX4_VSEL_table[] = { + 700, 1000, 1200, UNSUP(1300), + 1500, 1800, UNSUP(1850), 2500, + UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), + UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), +}; +static const u16 VMMC1_VSEL_table[] = { + 1850, 2850, 3000, 3150, +}; +static const u16 VMMC2_VSEL_table[] = { + UNSUP(1000), UNSUP(1000), UNSUP(1200), UNSUP(1300), + UNSUP(1500), UNSUP(1800), 1850, UNSUP(2500), + 2600, 2800, 2850, 3000, + 3150, 3150, 3150, 3150, +}; +static const u16 VPLL1_VSEL_table[] = { + 1000, 1200, 1300, 1800, + UNSUP(2800), UNSUP(3000), UNSUP(3000), UNSUP(3000), +}; +static const u16 VPLL2_VSEL_table[] = { + 700, 1000, 1200, 1300, + UNSUP(1500), 1800, UNSUP(1850), UNSUP(2500), + UNSUP(2600), UNSUP(2800), UNSUP(2850), UNSUP(3000), + UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), +}; +static const u16 VSIM_VSEL_table[] = { + UNSUP(1000), UNSUP(1200), UNSUP(1300), 1800, + 2800, 3000, 3000, 3000, +}; +static const u16 VDAC_VSEL_table[] = { + 1200, 1300, 1800, 1800, +}; + + +static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + int mV = info->table[index]; + + return IS_UNSUP(mV) ? 0 : (LDO_MV(mV) * 1000); +} + +static int +twl4030ldo_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + int vsel; + + for (vsel = 0; vsel < info->table_len; vsel++) { + int mV = info->table[vsel]; + int uV; + + if (IS_UNSUP(mV)) + continue; + uV = LDO_MV(mV) * 1000; + + /* REVISIT for VAUX2, first match may not be best/lowest */ + + /* use the first in-range value */ + if (min_uV <= uV && uV <= max_uV) + return twl4030reg_write(info, VREG_DEDICATED, vsel); + } + + return -EDOM; +} + +static int twl4030ldo_get_voltage(struct regulator_dev *rdev) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + int vsel = twl4030reg_read(info, VREG_DEDICATED); + + if (vsel < 0) + return vsel; + + vsel &= info->table_len - 1; + return LDO_MV(info->table[vsel]) * 1000; +} + +static struct regulator_ops twl4030ldo_ops = { + .list_voltage = twl4030ldo_list_voltage, + + .set_voltage = twl4030ldo_set_voltage, + .get_voltage = twl4030ldo_get_voltage, + + .enable = twl4030reg_enable, + .disable = twl4030reg_disable, + .is_enabled = twl4030reg_is_enabled, + + .set_mode = twl4030reg_set_mode, + + .get_status = twl4030reg_get_status, +}; + +/*----------------------------------------------------------------------*/ + +/* + * Fixed voltage LDOs don't have a VSEL field to update. + */ +static int twl4030fixed_list_voltage(struct regulator_dev *rdev, unsigned index) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + + return info->min_mV * 1000; +} + +static int twl4030fixed_get_voltage(struct regulator_dev *rdev) +{ + struct twlreg_info *info = rdev_get_drvdata(rdev); + + return info->min_mV * 1000; +} + +static struct regulator_ops twl4030fixed_ops = { + .list_voltage = twl4030fixed_list_voltage, + + .get_voltage = twl4030fixed_get_voltage, + + .enable = twl4030reg_enable, + .disable = twl4030reg_disable, + .is_enabled = twl4030reg_is_enabled, + + .set_mode = twl4030reg_set_mode, + + .get_status = twl4030reg_get_status, +}; + +/*----------------------------------------------------------------------*/ + +#define TWL_ADJUSTABLE_LDO(label, offset, num) { \ + .base = offset, \ + .id = num, \ + .table_len = ARRAY_SIZE(label##_VSEL_table), \ + .table = label##_VSEL_table, \ + .desc = { \ + .name = #label, \ + .id = TWL4030_REG_##label, \ + .n_voltages = ARRAY_SIZE(label##_VSEL_table), \ + .ops = &twl4030ldo_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + }, \ + } + +#define TWL_FIXED_LDO(label, offset, mVolts, num) { \ + .base = offset, \ + .id = num, \ + .min_mV = mVolts, \ + .desc = { \ + .name = #label, \ + .id = TWL4030_REG_##label, \ + .n_voltages = 1, \ + .ops = &twl4030fixed_ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + }, \ + } + +/* + * We list regulators here if systems need some level of + * software control over them after boot. + */ +static struct twlreg_info twl4030_regs[] = { + TWL_ADJUSTABLE_LDO(VAUX1, 0x17, 1), + TWL_ADJUSTABLE_LDO(VAUX2_4030, 0x1b, 2), + TWL_ADJUSTABLE_LDO(VAUX2, 0x1b, 2), + TWL_ADJUSTABLE_LDO(VAUX3, 0x1f, 3), + TWL_ADJUSTABLE_LDO(VAUX4, 0x23, 4), + TWL_ADJUSTABLE_LDO(VMMC1, 0x27, 5), + TWL_ADJUSTABLE_LDO(VMMC2, 0x2b, 6), + /* + TWL_ADJUSTABLE_LDO(VPLL1, 0x2f, 7), + */ + TWL_ADJUSTABLE_LDO(VPLL2, 0x33, 8), + TWL_ADJUSTABLE_LDO(VSIM, 0x37, 9), + TWL_ADJUSTABLE_LDO(VDAC, 0x3b, 10), + /* + TWL_ADJUSTABLE_LDO(VINTANA1, 0x3f, 11), + TWL_ADJUSTABLE_LDO(VINTANA2, 0x43, 12), + TWL_ADJUSTABLE_LDO(VINTDIG, 0x47, 13), + TWL_SMPS(VIO, 0x4b, 14), + TWL_SMPS(VDD1, 0x55, 15), + TWL_SMPS(VDD2, 0x63, 16), + */ + TWL_FIXED_LDO(VUSB1V5, 0x71, 1500, 17), + TWL_FIXED_LDO(VUSB1V8, 0x74, 1800, 18), + TWL_FIXED_LDO(VUSB3V1, 0x77, 3100, 19), + /* VUSBCP is managed *only* by the USB subchip */ +}; + +static int twl4030reg_probe(struct platform_device *pdev) +{ + int i; + struct twlreg_info *info; + struct regulator_init_data *initdata; + struct regulation_constraints *c; + struct regulator_dev *rdev; + + for (i = 0, info = NULL; i < ARRAY_SIZE(twl4030_regs); i++) { + if (twl4030_regs[i].desc.id != pdev->id) + continue; + info = twl4030_regs + i; + break; + } + if (!info) + return -ENODEV; + + initdata = pdev->dev.platform_data; + if (!initdata) + return -EINVAL; + + /* Constrain board-specific capabilities according to what + * this driver and the chip itself can actually do. + */ + c = &initdata->constraints; + c->valid_modes_mask &= REGULATOR_MODE_NORMAL | REGULATOR_MODE_STANDBY; + c->valid_ops_mask &= REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS; + + rdev = regulator_register(&info->desc, &pdev->dev, initdata, info); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "can't register %s, %ld\n", + info->desc.name, PTR_ERR(rdev)); + return PTR_ERR(rdev); + } + platform_set_drvdata(pdev, rdev); + + /* NOTE: many regulators support short-circuit IRQs (presentable + * as REGULATOR_OVER_CURRENT notifications?) configured via: + * - SC_CONFIG + * - SC_DETECT1 (vintana2, vmmc1/2, vaux1/2/3/4) + * - SC_DETECT2 (vusb, vdac, vio, vdd1/2, vpll2) + * - IT_CONFIG + */ + + return 0; +} + +static int __devexit twl4030reg_remove(struct platform_device *pdev) +{ + regulator_unregister(platform_get_drvdata(pdev)); + return 0; +} + +MODULE_ALIAS("platform:twl4030_reg"); + +static struct platform_driver twl4030reg_driver = { + .probe = twl4030reg_probe, + .remove = __devexit_p(twl4030reg_remove), + /* NOTE: short name, to work around driver model truncation of + * "twl4030_regulator.12" (and friends) to "twl4030_regulator.1". + */ + .driver.name = "twl4030_reg", + .driver.owner = THIS_MODULE, +}; + +static int __init twl4030reg_init(void) +{ + return platform_driver_register(&twl4030reg_driver); +} +subsys_initcall(twl4030reg_init); + +static void __exit twl4030reg_exit(void) +{ + platform_driver_unregister(&twl4030reg_driver); +} +module_exit(twl4030reg_exit) + +MODULE_DESCRIPTION("TWL4030 regulator driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/regulator/twl4030-regulator.c b/drivers/regulator/twl4030-regulator.c deleted file mode 100644 index e2032fb..0000000 --- a/drivers/regulator/twl4030-regulator.c +++ /dev/null @@ -1,500 +0,0 @@ -/* - * twl4030-regulator.c -- support regulators in twl4030 family chips - * - * Copyright (C) 2008 David Brownell - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include -#include -#include -#include -#include -#include -#include - - -/* - * The TWL4030/TW5030/TPS659x0 family chips include power management, a - * USB OTG transceiver, an RTC, ADC, PWM, and lots more. Some versions - * include an audio codec, battery charger, and more voltage regulators. - * These chips are often used in OMAP-based systems. - * - * This driver implements software-based resource control for various - * voltage regulators. This is usually augmented with state machine - * based control. - */ - -struct twlreg_info { - /* start of regulator's PM_RECEIVER control register bank */ - u8 base; - - /* twl4030 resource ID, for resource control state machine */ - u8 id; - - /* voltage in mV = table[VSEL]; table_len must be a power-of-two */ - u8 table_len; - const u16 *table; - - /* chip constraints on regulator behavior */ - u16 min_mV; - - /* used by regulator core */ - struct regulator_desc desc; -}; - - -/* LDO control registers ... offset is from the base of its register bank. - * The first three registers of all power resource banks help hardware to - * manage the various resource groups. - */ -#define VREG_GRP 0 -#define VREG_TYPE 1 -#define VREG_REMAP 2 -#define VREG_DEDICATED 3 /* LDO control */ - - -static inline int -twl4030reg_read(struct twlreg_info *info, unsigned offset) -{ - u8 value; - int status; - - status = twl4030_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, - &value, info->base + offset); - return (status < 0) ? status : value; -} - -static inline int -twl4030reg_write(struct twlreg_info *info, unsigned offset, u8 value) -{ - return twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, - value, info->base + offset); -} - -/*----------------------------------------------------------------------*/ - -/* generic power resource operations, which work on all regulators */ - -static int twl4030reg_grp(struct regulator_dev *rdev) -{ - return twl4030reg_read(rdev_get_drvdata(rdev), VREG_GRP); -} - -/* - * Enable/disable regulators by joining/leaving the P1 (processor) group. - * We assume nobody else is updating the DEV_GRP registers. - */ - -#define P3_GRP BIT(7) /* "peripherals" */ -#define P2_GRP BIT(6) /* secondary processor, modem, etc */ -#define P1_GRP BIT(5) /* CPU/Linux */ - -static int twl4030reg_is_enabled(struct regulator_dev *rdev) -{ - int state = twl4030reg_grp(rdev); - - if (state < 0) - return state; - - return (state & P1_GRP) != 0; -} - -static int twl4030reg_enable(struct regulator_dev *rdev) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - int grp; - - grp = twl4030reg_read(info, VREG_GRP); - if (grp < 0) - return grp; - - grp |= P1_GRP; - return twl4030reg_write(info, VREG_GRP, grp); -} - -static int twl4030reg_disable(struct regulator_dev *rdev) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - int grp; - - grp = twl4030reg_read(info, VREG_GRP); - if (grp < 0) - return grp; - - grp &= ~P1_GRP; - return twl4030reg_write(info, VREG_GRP, grp); -} - -static int twl4030reg_get_status(struct regulator_dev *rdev) -{ - int state = twl4030reg_grp(rdev); - - if (state < 0) - return state; - state &= 0x0f; - - /* assume state != WARM_RESET; we'd not be running... */ - if (!state) - return REGULATOR_STATUS_OFF; - return (state & BIT(3)) - ? REGULATOR_STATUS_NORMAL - : REGULATOR_STATUS_STANDBY; -} - -static int twl4030reg_set_mode(struct regulator_dev *rdev, unsigned mode) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - unsigned message; - int status; - - /* We can only set the mode through state machine commands... */ - switch (mode) { - case REGULATOR_MODE_NORMAL: - message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_ACTIVE); - break; - case REGULATOR_MODE_STANDBY: - message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_SLEEP); - break; - default: - return -EINVAL; - } - - /* Ensure the resource is associated with some group */ - status = twl4030reg_grp(rdev); - if (status < 0) - return status; - if (!(status & (P3_GRP | P2_GRP | P1_GRP))) - return -EACCES; - - status = twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, - message >> 8, 0x15 /* PB_WORD_MSB */ ); - if (status >= 0) - return status; - - return twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, - message, 0x16 /* PB_WORD_LSB */ ); -} - -/*----------------------------------------------------------------------*/ - -/* - * Support for adjustable-voltage LDOs uses a four bit (or less) voltage - * select field in its control register. We use tables indexed by VSEL - * to record voltages in milliVolts. (Accuracy is about three percent.) - * - * Note that VSEL values for VAUX2 changed in twl5030 and newer silicon; - * currently handled by listing two slightly different VAUX2 regulators, - * only one of which will be configured. - * - * VSEL values documented as "TI cannot support these values" are flagged - * in these tables as UNSUP() values; we normally won't assign them. - * - * VAUX3 at 3V is incorrectly listed in some TI manuals as unsupported. - * TI are revising the twl5030/tps659x0 specs to support that 3.0V setting. - */ -#ifdef CONFIG_TWL4030_ALLOW_UNSUPPORTED -#define UNSUP_MASK 0x0000 -#else -#define UNSUP_MASK 0x8000 -#endif - -#define UNSUP(x) (UNSUP_MASK | (x)) -#define IS_UNSUP(x) (UNSUP_MASK & (x)) -#define LDO_MV(x) (~UNSUP_MASK & (x)) - - -static const u16 VAUX1_VSEL_table[] = { - UNSUP(1500), UNSUP(1800), 2500, 2800, - 3000, 3000, 3000, 3000, -}; -static const u16 VAUX2_4030_VSEL_table[] = { - UNSUP(1000), UNSUP(1000), UNSUP(1200), 1300, - 1500, 1800, UNSUP(1850), 2500, - UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), - UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), -}; -static const u16 VAUX2_VSEL_table[] = { - 1700, 1700, 1900, 1300, - 1500, 1800, 2000, 2500, - 2100, 2800, 2200, 2300, - 2400, 2400, 2400, 2400, -}; -static const u16 VAUX3_VSEL_table[] = { - 1500, 1800, 2500, 2800, - 3000, 3000, 3000, 3000, -}; -static const u16 VAUX4_VSEL_table[] = { - 700, 1000, 1200, UNSUP(1300), - 1500, 1800, UNSUP(1850), 2500, - UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), - UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), -}; -static const u16 VMMC1_VSEL_table[] = { - 1850, 2850, 3000, 3150, -}; -static const u16 VMMC2_VSEL_table[] = { - UNSUP(1000), UNSUP(1000), UNSUP(1200), UNSUP(1300), - UNSUP(1500), UNSUP(1800), 1850, UNSUP(2500), - 2600, 2800, 2850, 3000, - 3150, 3150, 3150, 3150, -}; -static const u16 VPLL1_VSEL_table[] = { - 1000, 1200, 1300, 1800, - UNSUP(2800), UNSUP(3000), UNSUP(3000), UNSUP(3000), -}; -static const u16 VPLL2_VSEL_table[] = { - 700, 1000, 1200, 1300, - UNSUP(1500), 1800, UNSUP(1850), UNSUP(2500), - UNSUP(2600), UNSUP(2800), UNSUP(2850), UNSUP(3000), - UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), -}; -static const u16 VSIM_VSEL_table[] = { - UNSUP(1000), UNSUP(1200), UNSUP(1300), 1800, - 2800, 3000, 3000, 3000, -}; -static const u16 VDAC_VSEL_table[] = { - 1200, 1300, 1800, 1800, -}; - - -static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - int mV = info->table[index]; - - return IS_UNSUP(mV) ? 0 : (LDO_MV(mV) * 1000); -} - -static int -twl4030ldo_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - int vsel; - - for (vsel = 0; vsel < info->table_len; vsel++) { - int mV = info->table[vsel]; - int uV; - - if (IS_UNSUP(mV)) - continue; - uV = LDO_MV(mV) * 1000; - - /* REVISIT for VAUX2, first match may not be best/lowest */ - - /* use the first in-range value */ - if (min_uV <= uV && uV <= max_uV) - return twl4030reg_write(info, VREG_DEDICATED, vsel); - } - - return -EDOM; -} - -static int twl4030ldo_get_voltage(struct regulator_dev *rdev) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - int vsel = twl4030reg_read(info, VREG_DEDICATED); - - if (vsel < 0) - return vsel; - - vsel &= info->table_len - 1; - return LDO_MV(info->table[vsel]) * 1000; -} - -static struct regulator_ops twl4030ldo_ops = { - .list_voltage = twl4030ldo_list_voltage, - - .set_voltage = twl4030ldo_set_voltage, - .get_voltage = twl4030ldo_get_voltage, - - .enable = twl4030reg_enable, - .disable = twl4030reg_disable, - .is_enabled = twl4030reg_is_enabled, - - .set_mode = twl4030reg_set_mode, - - .get_status = twl4030reg_get_status, -}; - -/*----------------------------------------------------------------------*/ - -/* - * Fixed voltage LDOs don't have a VSEL field to update. - */ -static int twl4030fixed_list_voltage(struct regulator_dev *rdev, unsigned index) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - - return info->min_mV * 1000; -} - -static int twl4030fixed_get_voltage(struct regulator_dev *rdev) -{ - struct twlreg_info *info = rdev_get_drvdata(rdev); - - return info->min_mV * 1000; -} - -static struct regulator_ops twl4030fixed_ops = { - .list_voltage = twl4030fixed_list_voltage, - - .get_voltage = twl4030fixed_get_voltage, - - .enable = twl4030reg_enable, - .disable = twl4030reg_disable, - .is_enabled = twl4030reg_is_enabled, - - .set_mode = twl4030reg_set_mode, - - .get_status = twl4030reg_get_status, -}; - -/*----------------------------------------------------------------------*/ - -#define TWL_ADJUSTABLE_LDO(label, offset, num) { \ - .base = offset, \ - .id = num, \ - .table_len = ARRAY_SIZE(label##_VSEL_table), \ - .table = label##_VSEL_table, \ - .desc = { \ - .name = #label, \ - .id = TWL4030_REG_##label, \ - .n_voltages = ARRAY_SIZE(label##_VSEL_table), \ - .ops = &twl4030ldo_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - }, \ - } - -#define TWL_FIXED_LDO(label, offset, mVolts, num) { \ - .base = offset, \ - .id = num, \ - .min_mV = mVolts, \ - .desc = { \ - .name = #label, \ - .id = TWL4030_REG_##label, \ - .n_voltages = 1, \ - .ops = &twl4030fixed_ops, \ - .type = REGULATOR_VOLTAGE, \ - .owner = THIS_MODULE, \ - }, \ - } - -/* - * We list regulators here if systems need some level of - * software control over them after boot. - */ -static struct twlreg_info twl4030_regs[] = { - TWL_ADJUSTABLE_LDO(VAUX1, 0x17, 1), - TWL_ADJUSTABLE_LDO(VAUX2_4030, 0x1b, 2), - TWL_ADJUSTABLE_LDO(VAUX2, 0x1b, 2), - TWL_ADJUSTABLE_LDO(VAUX3, 0x1f, 3), - TWL_ADJUSTABLE_LDO(VAUX4, 0x23, 4), - TWL_ADJUSTABLE_LDO(VMMC1, 0x27, 5), - TWL_ADJUSTABLE_LDO(VMMC2, 0x2b, 6), - /* - TWL_ADJUSTABLE_LDO(VPLL1, 0x2f, 7), - */ - TWL_ADJUSTABLE_LDO(VPLL2, 0x33, 8), - TWL_ADJUSTABLE_LDO(VSIM, 0x37, 9), - TWL_ADJUSTABLE_LDO(VDAC, 0x3b, 10), - /* - TWL_ADJUSTABLE_LDO(VINTANA1, 0x3f, 11), - TWL_ADJUSTABLE_LDO(VINTANA2, 0x43, 12), - TWL_ADJUSTABLE_LDO(VINTDIG, 0x47, 13), - TWL_SMPS(VIO, 0x4b, 14), - TWL_SMPS(VDD1, 0x55, 15), - TWL_SMPS(VDD2, 0x63, 16), - */ - TWL_FIXED_LDO(VUSB1V5, 0x71, 1500, 17), - TWL_FIXED_LDO(VUSB1V8, 0x74, 1800, 18), - TWL_FIXED_LDO(VUSB3V1, 0x77, 3100, 19), - /* VUSBCP is managed *only* by the USB subchip */ -}; - -static int twl4030reg_probe(struct platform_device *pdev) -{ - int i; - struct twlreg_info *info; - struct regulator_init_data *initdata; - struct regulation_constraints *c; - struct regulator_dev *rdev; - - for (i = 0, info = NULL; i < ARRAY_SIZE(twl4030_regs); i++) { - if (twl4030_regs[i].desc.id != pdev->id) - continue; - info = twl4030_regs + i; - break; - } - if (!info) - return -ENODEV; - - initdata = pdev->dev.platform_data; - if (!initdata) - return -EINVAL; - - /* Constrain board-specific capabilities according to what - * this driver and the chip itself can actually do. - */ - c = &initdata->constraints; - c->valid_modes_mask &= REGULATOR_MODE_NORMAL | REGULATOR_MODE_STANDBY; - c->valid_ops_mask &= REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS; - - rdev = regulator_register(&info->desc, &pdev->dev, initdata, info); - if (IS_ERR(rdev)) { - dev_err(&pdev->dev, "can't register %s, %ld\n", - info->desc.name, PTR_ERR(rdev)); - return PTR_ERR(rdev); - } - platform_set_drvdata(pdev, rdev); - - /* NOTE: many regulators support short-circuit IRQs (presentable - * as REGULATOR_OVER_CURRENT notifications?) configured via: - * - SC_CONFIG - * - SC_DETECT1 (vintana2, vmmc1/2, vaux1/2/3/4) - * - SC_DETECT2 (vusb, vdac, vio, vdd1/2, vpll2) - * - IT_CONFIG - */ - - return 0; -} - -static int __devexit twl4030reg_remove(struct platform_device *pdev) -{ - regulator_unregister(platform_get_drvdata(pdev)); - return 0; -} - -MODULE_ALIAS("platform:twl4030_reg"); - -static struct platform_driver twl4030reg_driver = { - .probe = twl4030reg_probe, - .remove = __devexit_p(twl4030reg_remove), - /* NOTE: short name, to work around driver model truncation of - * "twl4030_regulator.12" (and friends) to "twl4030_regulator.1". - */ - .driver.name = "twl4030_reg", - .driver.owner = THIS_MODULE, -}; - -static int __init twl4030reg_init(void) -{ - return platform_driver_register(&twl4030reg_driver); -} -subsys_initcall(twl4030reg_init); - -static void __exit twl4030reg_exit(void) -{ - platform_driver_unregister(&twl4030reg_driver); -} -module_exit(twl4030reg_exit) - -MODULE_DESCRIPTION("TWL4030 regulator driver"); -MODULE_LICENSE("GPL"); diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile index af1ba7a..7da6efb 100644 --- a/drivers/rtc/Makefile +++ b/drivers/rtc/Makefile @@ -80,7 +80,7 @@ obj-$(CONFIG_RTC_DRV_STK17TA8) += rtc-stk17ta8.o obj-$(CONFIG_RTC_DRV_STMP) += rtc-stmp3xxx.o obj-$(CONFIG_RTC_DRV_SUN4V) += rtc-sun4v.o obj-$(CONFIG_RTC_DRV_TEST) += rtc-test.o -obj-$(CONFIG_RTC_DRV_TWL4030) += rtc-twl4030.o +obj-$(CONFIG_RTC_DRV_TWL4030) += rtc-twl.o obj-$(CONFIG_RTC_DRV_TX4939) += rtc-tx4939.o obj-$(CONFIG_RTC_DRV_V3020) += rtc-v3020.o obj-$(CONFIG_RTC_DRV_VR41XX) += rtc-vr41xx.o diff --git a/drivers/rtc/rtc-twl.c b/drivers/rtc/rtc-twl.c new file mode 100644 index 0000000..93565be --- /dev/null +++ b/drivers/rtc/rtc-twl.c @@ -0,0 +1,540 @@ +/* + * rtc-twl4030.c -- TWL4030 Real Time Clock interface + * + * Copyright (C) 2007 MontaVista Software, Inc + * Author: Alexandre Rusev + * + * Based on original TI driver twl4030-rtc.c + * Copyright (C) 2006 Texas Instruments, Inc. + * + * Based on rtc-omap.c + * Copyright (C) 2003 MontaVista Software, Inc. + * Author: George G. Davis or + * Copyright (C) 2006 David Brownell + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + + +/* + * RTC block register offsets (use TWL_MODULE_RTC) + */ +#define REG_SECONDS_REG 0x00 +#define REG_MINUTES_REG 0x01 +#define REG_HOURS_REG 0x02 +#define REG_DAYS_REG 0x03 +#define REG_MONTHS_REG 0x04 +#define REG_YEARS_REG 0x05 +#define REG_WEEKS_REG 0x06 + +#define REG_ALARM_SECONDS_REG 0x07 +#define REG_ALARM_MINUTES_REG 0x08 +#define REG_ALARM_HOURS_REG 0x09 +#define REG_ALARM_DAYS_REG 0x0A +#define REG_ALARM_MONTHS_REG 0x0B +#define REG_ALARM_YEARS_REG 0x0C + +#define REG_RTC_CTRL_REG 0x0D +#define REG_RTC_STATUS_REG 0x0E +#define REG_RTC_INTERRUPTS_REG 0x0F + +#define REG_RTC_COMP_LSB_REG 0x10 +#define REG_RTC_COMP_MSB_REG 0x11 + +/* RTC_CTRL_REG bitfields */ +#define BIT_RTC_CTRL_REG_STOP_RTC_M 0x01 +#define BIT_RTC_CTRL_REG_ROUND_30S_M 0x02 +#define BIT_RTC_CTRL_REG_AUTO_COMP_M 0x04 +#define BIT_RTC_CTRL_REG_MODE_12_24_M 0x08 +#define BIT_RTC_CTRL_REG_TEST_MODE_M 0x10 +#define BIT_RTC_CTRL_REG_SET_32_COUNTER_M 0x20 +#define BIT_RTC_CTRL_REG_GET_TIME_M 0x40 + +/* RTC_STATUS_REG bitfields */ +#define BIT_RTC_STATUS_REG_RUN_M 0x02 +#define BIT_RTC_STATUS_REG_1S_EVENT_M 0x04 +#define BIT_RTC_STATUS_REG_1M_EVENT_M 0x08 +#define BIT_RTC_STATUS_REG_1H_EVENT_M 0x10 +#define BIT_RTC_STATUS_REG_1D_EVENT_M 0x20 +#define BIT_RTC_STATUS_REG_ALARM_M 0x40 +#define BIT_RTC_STATUS_REG_POWER_UP_M 0x80 + +/* RTC_INTERRUPTS_REG bitfields */ +#define BIT_RTC_INTERRUPTS_REG_EVERY_M 0x03 +#define BIT_RTC_INTERRUPTS_REG_IT_TIMER_M 0x04 +#define BIT_RTC_INTERRUPTS_REG_IT_ALARM_M 0x08 + + +/* REG_SECONDS_REG through REG_YEARS_REG is how many registers? */ +#define ALL_TIME_REGS 6 + +/*----------------------------------------------------------------------*/ + +/* + * Supports 1 byte read from TWL4030 RTC register. + */ +static int twl4030_rtc_read_u8(u8 *data, u8 reg) +{ + int ret; + + ret = twl4030_i2c_read_u8(TWL4030_MODULE_RTC, data, reg); + if (ret < 0) + pr_err("twl4030_rtc: Could not read TWL4030" + "register %X - error %d\n", reg, ret); + return ret; +} + +/* + * Supports 1 byte write to TWL4030 RTC registers. + */ +static int twl4030_rtc_write_u8(u8 data, u8 reg) +{ + int ret; + + ret = twl4030_i2c_write_u8(TWL4030_MODULE_RTC, data, reg); + if (ret < 0) + pr_err("twl4030_rtc: Could not write TWL4030" + "register %X - error %d\n", reg, ret); + return ret; +} + +/* + * Cache the value for timer/alarm interrupts register; this is + * only changed by callers holding rtc ops lock (or resume). + */ +static unsigned char rtc_irq_bits; + +/* + * Enable 1/second update and/or alarm interrupts. + */ +static int set_rtc_irq_bit(unsigned char bit) +{ + unsigned char val; + int ret; + + val = rtc_irq_bits | bit; + val &= ~BIT_RTC_INTERRUPTS_REG_EVERY_M; + ret = twl4030_rtc_write_u8(val, REG_RTC_INTERRUPTS_REG); + if (ret == 0) + rtc_irq_bits = val; + + return ret; +} + +/* + * Disable update and/or alarm interrupts. + */ +static int mask_rtc_irq_bit(unsigned char bit) +{ + unsigned char val; + int ret; + + val = rtc_irq_bits & ~bit; + ret = twl4030_rtc_write_u8(val, REG_RTC_INTERRUPTS_REG); + if (ret == 0) + rtc_irq_bits = val; + + return ret; +} + +static int twl4030_rtc_alarm_irq_enable(struct device *dev, unsigned enabled) +{ + int ret; + + if (enabled) + ret = set_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M); + else + ret = mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M); + + return ret; +} + +static int twl4030_rtc_update_irq_enable(struct device *dev, unsigned enabled) +{ + int ret; + + if (enabled) + ret = set_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); + else + ret = mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); + + return ret; +} + +/* + * Gets current TWL4030 RTC time and date parameters. + * + * The RTC's time/alarm representation is not what gmtime(3) requires + * Linux to use: + * + * - Months are 1..12 vs Linux 0-11 + * - Years are 0..99 vs Linux 1900..N (we assume 21st century) + */ +static int twl4030_rtc_read_time(struct device *dev, struct rtc_time *tm) +{ + unsigned char rtc_data[ALL_TIME_REGS + 1]; + int ret; + u8 save_control; + + ret = twl4030_rtc_read_u8(&save_control, REG_RTC_CTRL_REG); + if (ret < 0) + return ret; + + save_control |= BIT_RTC_CTRL_REG_GET_TIME_M; + + ret = twl4030_rtc_write_u8(save_control, REG_RTC_CTRL_REG); + if (ret < 0) + return ret; + + ret = twl4030_i2c_read(TWL4030_MODULE_RTC, rtc_data, + REG_SECONDS_REG, ALL_TIME_REGS); + + if (ret < 0) { + dev_err(dev, "rtc_read_time error %d\n", ret); + return ret; + } + + tm->tm_sec = bcd2bin(rtc_data[0]); + tm->tm_min = bcd2bin(rtc_data[1]); + tm->tm_hour = bcd2bin(rtc_data[2]); + tm->tm_mday = bcd2bin(rtc_data[3]); + tm->tm_mon = bcd2bin(rtc_data[4]) - 1; + tm->tm_year = bcd2bin(rtc_data[5]) + 100; + + return ret; +} + +static int twl4030_rtc_set_time(struct device *dev, struct rtc_time *tm) +{ + unsigned char save_control; + unsigned char rtc_data[ALL_TIME_REGS + 1]; + int ret; + + rtc_data[1] = bin2bcd(tm->tm_sec); + rtc_data[2] = bin2bcd(tm->tm_min); + rtc_data[3] = bin2bcd(tm->tm_hour); + rtc_data[4] = bin2bcd(tm->tm_mday); + rtc_data[5] = bin2bcd(tm->tm_mon + 1); + rtc_data[6] = bin2bcd(tm->tm_year - 100); + + /* Stop RTC while updating the TC registers */ + ret = twl4030_rtc_read_u8(&save_control, REG_RTC_CTRL_REG); + if (ret < 0) + goto out; + + save_control &= ~BIT_RTC_CTRL_REG_STOP_RTC_M; + twl4030_rtc_write_u8(save_control, REG_RTC_CTRL_REG); + if (ret < 0) + goto out; + + /* update all the time registers in one shot */ + ret = twl4030_i2c_write(TWL4030_MODULE_RTC, rtc_data, + REG_SECONDS_REG, ALL_TIME_REGS); + if (ret < 0) { + dev_err(dev, "rtc_set_time error %d\n", ret); + goto out; + } + + /* Start back RTC */ + save_control |= BIT_RTC_CTRL_REG_STOP_RTC_M; + ret = twl4030_rtc_write_u8(save_control, REG_RTC_CTRL_REG); + +out: + return ret; +} + +/* + * Gets current TWL4030 RTC alarm time. + */ +static int twl4030_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alm) +{ + unsigned char rtc_data[ALL_TIME_REGS + 1]; + int ret; + + ret = twl4030_i2c_read(TWL4030_MODULE_RTC, rtc_data, + REG_ALARM_SECONDS_REG, ALL_TIME_REGS); + if (ret < 0) { + dev_err(dev, "rtc_read_alarm error %d\n", ret); + return ret; + } + + /* some of these fields may be wildcard/"match all" */ + alm->time.tm_sec = bcd2bin(rtc_data[0]); + alm->time.tm_min = bcd2bin(rtc_data[1]); + alm->time.tm_hour = bcd2bin(rtc_data[2]); + alm->time.tm_mday = bcd2bin(rtc_data[3]); + alm->time.tm_mon = bcd2bin(rtc_data[4]) - 1; + alm->time.tm_year = bcd2bin(rtc_data[5]) + 100; + + /* report cached alarm enable state */ + if (rtc_irq_bits & BIT_RTC_INTERRUPTS_REG_IT_ALARM_M) + alm->enabled = 1; + + return ret; +} + +static int twl4030_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alm) +{ + unsigned char alarm_data[ALL_TIME_REGS + 1]; + int ret; + + ret = twl4030_rtc_alarm_irq_enable(dev, 0); + if (ret) + goto out; + + alarm_data[1] = bin2bcd(alm->time.tm_sec); + alarm_data[2] = bin2bcd(alm->time.tm_min); + alarm_data[3] = bin2bcd(alm->time.tm_hour); + alarm_data[4] = bin2bcd(alm->time.tm_mday); + alarm_data[5] = bin2bcd(alm->time.tm_mon + 1); + alarm_data[6] = bin2bcd(alm->time.tm_year - 100); + + /* update all the alarm registers in one shot */ + ret = twl4030_i2c_write(TWL4030_MODULE_RTC, alarm_data, + REG_ALARM_SECONDS_REG, ALL_TIME_REGS); + if (ret) { + dev_err(dev, "rtc_set_alarm error %d\n", ret); + goto out; + } + + if (alm->enabled) + ret = twl4030_rtc_alarm_irq_enable(dev, 1); +out: + return ret; +} + +static irqreturn_t twl4030_rtc_interrupt(int irq, void *rtc) +{ + unsigned long events = 0; + int ret = IRQ_NONE; + int res; + u8 rd_reg; + +#ifdef CONFIG_LOCKDEP + /* WORKAROUND for lockdep forcing IRQF_DISABLED on us, which + * we don't want and can't tolerate. Although it might be + * friendlier not to borrow this thread context... + */ + local_irq_enable(); +#endif + + res = twl4030_rtc_read_u8(&rd_reg, REG_RTC_STATUS_REG); + if (res) + goto out; + /* + * Figure out source of interrupt: ALARM or TIMER in RTC_STATUS_REG. + * only one (ALARM or RTC) interrupt source may be enabled + * at time, we also could check our results + * by reading RTS_INTERRUPTS_REGISTER[IT_TIMER,IT_ALARM] + */ + if (rd_reg & BIT_RTC_STATUS_REG_ALARM_M) + events |= RTC_IRQF | RTC_AF; + else + events |= RTC_IRQF | RTC_UF; + + res = twl4030_rtc_write_u8(rd_reg | BIT_RTC_STATUS_REG_ALARM_M, + REG_RTC_STATUS_REG); + if (res) + goto out; + + /* Clear on Read enabled. RTC_IT bit of TWL4030_INT_PWR_ISR1 + * needs 2 reads to clear the interrupt. One read is done in + * do_twl4030_pwrirq(). Doing the second read, to clear + * the bit. + * + * FIXME the reason PWR_ISR1 needs an extra read is that + * RTC_IF retriggered until we cleared REG_ALARM_M above. + * But re-reading like this is a bad hack; by doing so we + * risk wrongly clearing status for some other IRQ (losing + * the interrupt). Be smarter about handling RTC_UF ... + */ + res = twl4030_i2c_read_u8(TWL4030_MODULE_INT, + &rd_reg, TWL4030_INT_PWR_ISR1); + if (res) + goto out; + + /* Notify RTC core on event */ + rtc_update_irq(rtc, 1, events); + + ret = IRQ_HANDLED; +out: + return ret; +} + +static struct rtc_class_ops twl4030_rtc_ops = { + .read_time = twl4030_rtc_read_time, + .set_time = twl4030_rtc_set_time, + .read_alarm = twl4030_rtc_read_alarm, + .set_alarm = twl4030_rtc_set_alarm, + .alarm_irq_enable = twl4030_rtc_alarm_irq_enable, + .update_irq_enable = twl4030_rtc_update_irq_enable, +}; + +/*----------------------------------------------------------------------*/ + +static int __devinit twl4030_rtc_probe(struct platform_device *pdev) +{ + struct rtc_device *rtc; + int ret = 0; + int irq = platform_get_irq(pdev, 0); + u8 rd_reg; + + if (irq <= 0) + return -EINVAL; + + rtc = rtc_device_register(pdev->name, + &pdev->dev, &twl4030_rtc_ops, THIS_MODULE); + if (IS_ERR(rtc)) { + ret = PTR_ERR(rtc); + dev_err(&pdev->dev, "can't register RTC device, err %ld\n", + PTR_ERR(rtc)); + goto out0; + + } + + platform_set_drvdata(pdev, rtc); + + ret = twl4030_rtc_read_u8(&rd_reg, REG_RTC_STATUS_REG); + if (ret < 0) + goto out1; + + if (rd_reg & BIT_RTC_STATUS_REG_POWER_UP_M) + dev_warn(&pdev->dev, "Power up reset detected.\n"); + + if (rd_reg & BIT_RTC_STATUS_REG_ALARM_M) + dev_warn(&pdev->dev, "Pending Alarm interrupt detected.\n"); + + /* Clear RTC Power up reset and pending alarm interrupts */ + ret = twl4030_rtc_write_u8(rd_reg, REG_RTC_STATUS_REG); + if (ret < 0) + goto out1; + + ret = request_irq(irq, twl4030_rtc_interrupt, + IRQF_TRIGGER_RISING, + dev_name(&rtc->dev), rtc); + if (ret < 0) { + dev_err(&pdev->dev, "IRQ is not free.\n"); + goto out1; + } + + /* Check RTC module status, Enable if it is off */ + ret = twl4030_rtc_read_u8(&rd_reg, REG_RTC_CTRL_REG); + if (ret < 0) + goto out2; + + if (!(rd_reg & BIT_RTC_CTRL_REG_STOP_RTC_M)) { + dev_info(&pdev->dev, "Enabling TWL4030-RTC.\n"); + rd_reg = BIT_RTC_CTRL_REG_STOP_RTC_M; + ret = twl4030_rtc_write_u8(rd_reg, REG_RTC_CTRL_REG); + if (ret < 0) + goto out2; + } + + /* init cached IRQ enable bits */ + ret = twl4030_rtc_read_u8(&rtc_irq_bits, REG_RTC_INTERRUPTS_REG); + if (ret < 0) + goto out2; + + return ret; + +out2: + free_irq(irq, rtc); +out1: + rtc_device_unregister(rtc); +out0: + return ret; +} + +/* + * Disable all TWL4030 RTC module interrupts. + * Sets status flag to free. + */ +static int __devexit twl4030_rtc_remove(struct platform_device *pdev) +{ + /* leave rtc running, but disable irqs */ + struct rtc_device *rtc = platform_get_drvdata(pdev); + int irq = platform_get_irq(pdev, 0); + + mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M); + mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); + + free_irq(irq, rtc); + + rtc_device_unregister(rtc); + platform_set_drvdata(pdev, NULL); + return 0; +} + +static void twl4030_rtc_shutdown(struct platform_device *pdev) +{ + /* mask timer interrupts, but leave alarm interrupts on to enable + power-on when alarm is triggered */ + mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); +} + +#ifdef CONFIG_PM + +static unsigned char irqstat; + +static int twl4030_rtc_suspend(struct platform_device *pdev, pm_message_t state) +{ + irqstat = rtc_irq_bits; + + mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); + return 0; +} + +static int twl4030_rtc_resume(struct platform_device *pdev) +{ + set_rtc_irq_bit(irqstat); + return 0; +} + +#else +#define twl4030_rtc_suspend NULL +#define twl4030_rtc_resume NULL +#endif + +MODULE_ALIAS("platform:twl4030_rtc"); + +static struct platform_driver twl4030rtc_driver = { + .probe = twl4030_rtc_probe, + .remove = __devexit_p(twl4030_rtc_remove), + .shutdown = twl4030_rtc_shutdown, + .suspend = twl4030_rtc_suspend, + .resume = twl4030_rtc_resume, + .driver = { + .owner = THIS_MODULE, + .name = "twl4030_rtc", + }, +}; + +static int __init twl4030_rtc_init(void) +{ + return platform_driver_register(&twl4030rtc_driver); +} +module_init(twl4030_rtc_init); + +static void __exit twl4030_rtc_exit(void) +{ + platform_driver_unregister(&twl4030rtc_driver); +} +module_exit(twl4030_rtc_exit); + +MODULE_AUTHOR("Texas Instruments, MontaVista Software"); +MODULE_LICENSE("GPL"); diff --git a/drivers/rtc/rtc-twl4030.c b/drivers/rtc/rtc-twl4030.c deleted file mode 100644 index 9c8c70c..0000000 --- a/drivers/rtc/rtc-twl4030.c +++ /dev/null @@ -1,540 +0,0 @@ -/* - * rtc-twl4030.c -- TWL4030 Real Time Clock interface - * - * Copyright (C) 2007 MontaVista Software, Inc - * Author: Alexandre Rusev - * - * Based on original TI driver twl4030-rtc.c - * Copyright (C) 2006 Texas Instruments, Inc. - * - * Based on rtc-omap.c - * Copyright (C) 2003 MontaVista Software, Inc. - * Author: George G. Davis or - * Copyright (C) 2006 David Brownell - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include - - -/* - * RTC block register offsets (use TWL_MODULE_RTC) - */ -#define REG_SECONDS_REG 0x00 -#define REG_MINUTES_REG 0x01 -#define REG_HOURS_REG 0x02 -#define REG_DAYS_REG 0x03 -#define REG_MONTHS_REG 0x04 -#define REG_YEARS_REG 0x05 -#define REG_WEEKS_REG 0x06 - -#define REG_ALARM_SECONDS_REG 0x07 -#define REG_ALARM_MINUTES_REG 0x08 -#define REG_ALARM_HOURS_REG 0x09 -#define REG_ALARM_DAYS_REG 0x0A -#define REG_ALARM_MONTHS_REG 0x0B -#define REG_ALARM_YEARS_REG 0x0C - -#define REG_RTC_CTRL_REG 0x0D -#define REG_RTC_STATUS_REG 0x0E -#define REG_RTC_INTERRUPTS_REG 0x0F - -#define REG_RTC_COMP_LSB_REG 0x10 -#define REG_RTC_COMP_MSB_REG 0x11 - -/* RTC_CTRL_REG bitfields */ -#define BIT_RTC_CTRL_REG_STOP_RTC_M 0x01 -#define BIT_RTC_CTRL_REG_ROUND_30S_M 0x02 -#define BIT_RTC_CTRL_REG_AUTO_COMP_M 0x04 -#define BIT_RTC_CTRL_REG_MODE_12_24_M 0x08 -#define BIT_RTC_CTRL_REG_TEST_MODE_M 0x10 -#define BIT_RTC_CTRL_REG_SET_32_COUNTER_M 0x20 -#define BIT_RTC_CTRL_REG_GET_TIME_M 0x40 - -/* RTC_STATUS_REG bitfields */ -#define BIT_RTC_STATUS_REG_RUN_M 0x02 -#define BIT_RTC_STATUS_REG_1S_EVENT_M 0x04 -#define BIT_RTC_STATUS_REG_1M_EVENT_M 0x08 -#define BIT_RTC_STATUS_REG_1H_EVENT_M 0x10 -#define BIT_RTC_STATUS_REG_1D_EVENT_M 0x20 -#define BIT_RTC_STATUS_REG_ALARM_M 0x40 -#define BIT_RTC_STATUS_REG_POWER_UP_M 0x80 - -/* RTC_INTERRUPTS_REG bitfields */ -#define BIT_RTC_INTERRUPTS_REG_EVERY_M 0x03 -#define BIT_RTC_INTERRUPTS_REG_IT_TIMER_M 0x04 -#define BIT_RTC_INTERRUPTS_REG_IT_ALARM_M 0x08 - - -/* REG_SECONDS_REG through REG_YEARS_REG is how many registers? */ -#define ALL_TIME_REGS 6 - -/*----------------------------------------------------------------------*/ - -/* - * Supports 1 byte read from TWL4030 RTC register. - */ -static int twl4030_rtc_read_u8(u8 *data, u8 reg) -{ - int ret; - - ret = twl4030_i2c_read_u8(TWL4030_MODULE_RTC, data, reg); - if (ret < 0) - pr_err("twl4030_rtc: Could not read TWL4030" - "register %X - error %d\n", reg, ret); - return ret; -} - -/* - * Supports 1 byte write to TWL4030 RTC registers. - */ -static int twl4030_rtc_write_u8(u8 data, u8 reg) -{ - int ret; - - ret = twl4030_i2c_write_u8(TWL4030_MODULE_RTC, data, reg); - if (ret < 0) - pr_err("twl4030_rtc: Could not write TWL4030" - "register %X - error %d\n", reg, ret); - return ret; -} - -/* - * Cache the value for timer/alarm interrupts register; this is - * only changed by callers holding rtc ops lock (or resume). - */ -static unsigned char rtc_irq_bits; - -/* - * Enable 1/second update and/or alarm interrupts. - */ -static int set_rtc_irq_bit(unsigned char bit) -{ - unsigned char val; - int ret; - - val = rtc_irq_bits | bit; - val &= ~BIT_RTC_INTERRUPTS_REG_EVERY_M; - ret = twl4030_rtc_write_u8(val, REG_RTC_INTERRUPTS_REG); - if (ret == 0) - rtc_irq_bits = val; - - return ret; -} - -/* - * Disable update and/or alarm interrupts. - */ -static int mask_rtc_irq_bit(unsigned char bit) -{ - unsigned char val; - int ret; - - val = rtc_irq_bits & ~bit; - ret = twl4030_rtc_write_u8(val, REG_RTC_INTERRUPTS_REG); - if (ret == 0) - rtc_irq_bits = val; - - return ret; -} - -static int twl4030_rtc_alarm_irq_enable(struct device *dev, unsigned enabled) -{ - int ret; - - if (enabled) - ret = set_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M); - else - ret = mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M); - - return ret; -} - -static int twl4030_rtc_update_irq_enable(struct device *dev, unsigned enabled) -{ - int ret; - - if (enabled) - ret = set_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); - else - ret = mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); - - return ret; -} - -/* - * Gets current TWL4030 RTC time and date parameters. - * - * The RTC's time/alarm representation is not what gmtime(3) requires - * Linux to use: - * - * - Months are 1..12 vs Linux 0-11 - * - Years are 0..99 vs Linux 1900..N (we assume 21st century) - */ -static int twl4030_rtc_read_time(struct device *dev, struct rtc_time *tm) -{ - unsigned char rtc_data[ALL_TIME_REGS + 1]; - int ret; - u8 save_control; - - ret = twl4030_rtc_read_u8(&save_control, REG_RTC_CTRL_REG); - if (ret < 0) - return ret; - - save_control |= BIT_RTC_CTRL_REG_GET_TIME_M; - - ret = twl4030_rtc_write_u8(save_control, REG_RTC_CTRL_REG); - if (ret < 0) - return ret; - - ret = twl4030_i2c_read(TWL4030_MODULE_RTC, rtc_data, - REG_SECONDS_REG, ALL_TIME_REGS); - - if (ret < 0) { - dev_err(dev, "rtc_read_time error %d\n", ret); - return ret; - } - - tm->tm_sec = bcd2bin(rtc_data[0]); - tm->tm_min = bcd2bin(rtc_data[1]); - tm->tm_hour = bcd2bin(rtc_data[2]); - tm->tm_mday = bcd2bin(rtc_data[3]); - tm->tm_mon = bcd2bin(rtc_data[4]) - 1; - tm->tm_year = bcd2bin(rtc_data[5]) + 100; - - return ret; -} - -static int twl4030_rtc_set_time(struct device *dev, struct rtc_time *tm) -{ - unsigned char save_control; - unsigned char rtc_data[ALL_TIME_REGS + 1]; - int ret; - - rtc_data[1] = bin2bcd(tm->tm_sec); - rtc_data[2] = bin2bcd(tm->tm_min); - rtc_data[3] = bin2bcd(tm->tm_hour); - rtc_data[4] = bin2bcd(tm->tm_mday); - rtc_data[5] = bin2bcd(tm->tm_mon + 1); - rtc_data[6] = bin2bcd(tm->tm_year - 100); - - /* Stop RTC while updating the TC registers */ - ret = twl4030_rtc_read_u8(&save_control, REG_RTC_CTRL_REG); - if (ret < 0) - goto out; - - save_control &= ~BIT_RTC_CTRL_REG_STOP_RTC_M; - twl4030_rtc_write_u8(save_control, REG_RTC_CTRL_REG); - if (ret < 0) - goto out; - - /* update all the time registers in one shot */ - ret = twl4030_i2c_write(TWL4030_MODULE_RTC, rtc_data, - REG_SECONDS_REG, ALL_TIME_REGS); - if (ret < 0) { - dev_err(dev, "rtc_set_time error %d\n", ret); - goto out; - } - - /* Start back RTC */ - save_control |= BIT_RTC_CTRL_REG_STOP_RTC_M; - ret = twl4030_rtc_write_u8(save_control, REG_RTC_CTRL_REG); - -out: - return ret; -} - -/* - * Gets current TWL4030 RTC alarm time. - */ -static int twl4030_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alm) -{ - unsigned char rtc_data[ALL_TIME_REGS + 1]; - int ret; - - ret = twl4030_i2c_read(TWL4030_MODULE_RTC, rtc_data, - REG_ALARM_SECONDS_REG, ALL_TIME_REGS); - if (ret < 0) { - dev_err(dev, "rtc_read_alarm error %d\n", ret); - return ret; - } - - /* some of these fields may be wildcard/"match all" */ - alm->time.tm_sec = bcd2bin(rtc_data[0]); - alm->time.tm_min = bcd2bin(rtc_data[1]); - alm->time.tm_hour = bcd2bin(rtc_data[2]); - alm->time.tm_mday = bcd2bin(rtc_data[3]); - alm->time.tm_mon = bcd2bin(rtc_data[4]) - 1; - alm->time.tm_year = bcd2bin(rtc_data[5]) + 100; - - /* report cached alarm enable state */ - if (rtc_irq_bits & BIT_RTC_INTERRUPTS_REG_IT_ALARM_M) - alm->enabled = 1; - - return ret; -} - -static int twl4030_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alm) -{ - unsigned char alarm_data[ALL_TIME_REGS + 1]; - int ret; - - ret = twl4030_rtc_alarm_irq_enable(dev, 0); - if (ret) - goto out; - - alarm_data[1] = bin2bcd(alm->time.tm_sec); - alarm_data[2] = bin2bcd(alm->time.tm_min); - alarm_data[3] = bin2bcd(alm->time.tm_hour); - alarm_data[4] = bin2bcd(alm->time.tm_mday); - alarm_data[5] = bin2bcd(alm->time.tm_mon + 1); - alarm_data[6] = bin2bcd(alm->time.tm_year - 100); - - /* update all the alarm registers in one shot */ - ret = twl4030_i2c_write(TWL4030_MODULE_RTC, alarm_data, - REG_ALARM_SECONDS_REG, ALL_TIME_REGS); - if (ret) { - dev_err(dev, "rtc_set_alarm error %d\n", ret); - goto out; - } - - if (alm->enabled) - ret = twl4030_rtc_alarm_irq_enable(dev, 1); -out: - return ret; -} - -static irqreturn_t twl4030_rtc_interrupt(int irq, void *rtc) -{ - unsigned long events = 0; - int ret = IRQ_NONE; - int res; - u8 rd_reg; - -#ifdef CONFIG_LOCKDEP - /* WORKAROUND for lockdep forcing IRQF_DISABLED on us, which - * we don't want and can't tolerate. Although it might be - * friendlier not to borrow this thread context... - */ - local_irq_enable(); -#endif - - res = twl4030_rtc_read_u8(&rd_reg, REG_RTC_STATUS_REG); - if (res) - goto out; - /* - * Figure out source of interrupt: ALARM or TIMER in RTC_STATUS_REG. - * only one (ALARM or RTC) interrupt source may be enabled - * at time, we also could check our results - * by reading RTS_INTERRUPTS_REGISTER[IT_TIMER,IT_ALARM] - */ - if (rd_reg & BIT_RTC_STATUS_REG_ALARM_M) - events |= RTC_IRQF | RTC_AF; - else - events |= RTC_IRQF | RTC_UF; - - res = twl4030_rtc_write_u8(rd_reg | BIT_RTC_STATUS_REG_ALARM_M, - REG_RTC_STATUS_REG); - if (res) - goto out; - - /* Clear on Read enabled. RTC_IT bit of TWL4030_INT_PWR_ISR1 - * needs 2 reads to clear the interrupt. One read is done in - * do_twl4030_pwrirq(). Doing the second read, to clear - * the bit. - * - * FIXME the reason PWR_ISR1 needs an extra read is that - * RTC_IF retriggered until we cleared REG_ALARM_M above. - * But re-reading like this is a bad hack; by doing so we - * risk wrongly clearing status for some other IRQ (losing - * the interrupt). Be smarter about handling RTC_UF ... - */ - res = twl4030_i2c_read_u8(TWL4030_MODULE_INT, - &rd_reg, TWL4030_INT_PWR_ISR1); - if (res) - goto out; - - /* Notify RTC core on event */ - rtc_update_irq(rtc, 1, events); - - ret = IRQ_HANDLED; -out: - return ret; -} - -static struct rtc_class_ops twl4030_rtc_ops = { - .read_time = twl4030_rtc_read_time, - .set_time = twl4030_rtc_set_time, - .read_alarm = twl4030_rtc_read_alarm, - .set_alarm = twl4030_rtc_set_alarm, - .alarm_irq_enable = twl4030_rtc_alarm_irq_enable, - .update_irq_enable = twl4030_rtc_update_irq_enable, -}; - -/*----------------------------------------------------------------------*/ - -static int __devinit twl4030_rtc_probe(struct platform_device *pdev) -{ - struct rtc_device *rtc; - int ret = 0; - int irq = platform_get_irq(pdev, 0); - u8 rd_reg; - - if (irq <= 0) - return -EINVAL; - - rtc = rtc_device_register(pdev->name, - &pdev->dev, &twl4030_rtc_ops, THIS_MODULE); - if (IS_ERR(rtc)) { - ret = PTR_ERR(rtc); - dev_err(&pdev->dev, "can't register RTC device, err %ld\n", - PTR_ERR(rtc)); - goto out0; - - } - - platform_set_drvdata(pdev, rtc); - - ret = twl4030_rtc_read_u8(&rd_reg, REG_RTC_STATUS_REG); - if (ret < 0) - goto out1; - - if (rd_reg & BIT_RTC_STATUS_REG_POWER_UP_M) - dev_warn(&pdev->dev, "Power up reset detected.\n"); - - if (rd_reg & BIT_RTC_STATUS_REG_ALARM_M) - dev_warn(&pdev->dev, "Pending Alarm interrupt detected.\n"); - - /* Clear RTC Power up reset and pending alarm interrupts */ - ret = twl4030_rtc_write_u8(rd_reg, REG_RTC_STATUS_REG); - if (ret < 0) - goto out1; - - ret = request_irq(irq, twl4030_rtc_interrupt, - IRQF_TRIGGER_RISING, - dev_name(&rtc->dev), rtc); - if (ret < 0) { - dev_err(&pdev->dev, "IRQ is not free.\n"); - goto out1; - } - - /* Check RTC module status, Enable if it is off */ - ret = twl4030_rtc_read_u8(&rd_reg, REG_RTC_CTRL_REG); - if (ret < 0) - goto out2; - - if (!(rd_reg & BIT_RTC_CTRL_REG_STOP_RTC_M)) { - dev_info(&pdev->dev, "Enabling TWL4030-RTC.\n"); - rd_reg = BIT_RTC_CTRL_REG_STOP_RTC_M; - ret = twl4030_rtc_write_u8(rd_reg, REG_RTC_CTRL_REG); - if (ret < 0) - goto out2; - } - - /* init cached IRQ enable bits */ - ret = twl4030_rtc_read_u8(&rtc_irq_bits, REG_RTC_INTERRUPTS_REG); - if (ret < 0) - goto out2; - - return ret; - -out2: - free_irq(irq, rtc); -out1: - rtc_device_unregister(rtc); -out0: - return ret; -} - -/* - * Disable all TWL4030 RTC module interrupts. - * Sets status flag to free. - */ -static int __devexit twl4030_rtc_remove(struct platform_device *pdev) -{ - /* leave rtc running, but disable irqs */ - struct rtc_device *rtc = platform_get_drvdata(pdev); - int irq = platform_get_irq(pdev, 0); - - mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M); - mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); - - free_irq(irq, rtc); - - rtc_device_unregister(rtc); - platform_set_drvdata(pdev, NULL); - return 0; -} - -static void twl4030_rtc_shutdown(struct platform_device *pdev) -{ - /* mask timer interrupts, but leave alarm interrupts on to enable - power-on when alarm is triggered */ - mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); -} - -#ifdef CONFIG_PM - -static unsigned char irqstat; - -static int twl4030_rtc_suspend(struct platform_device *pdev, pm_message_t state) -{ - irqstat = rtc_irq_bits; - - mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M); - return 0; -} - -static int twl4030_rtc_resume(struct platform_device *pdev) -{ - set_rtc_irq_bit(irqstat); - return 0; -} - -#else -#define twl4030_rtc_suspend NULL -#define twl4030_rtc_resume NULL -#endif - -MODULE_ALIAS("platform:twl4030_rtc"); - -static struct platform_driver twl4030rtc_driver = { - .probe = twl4030_rtc_probe, - .remove = __devexit_p(twl4030_rtc_remove), - .shutdown = twl4030_rtc_shutdown, - .suspend = twl4030_rtc_suspend, - .resume = twl4030_rtc_resume, - .driver = { - .owner = THIS_MODULE, - .name = "twl4030_rtc", - }, -}; - -static int __init twl4030_rtc_init(void) -{ - return platform_driver_register(&twl4030rtc_driver); -} -module_init(twl4030_rtc_init); - -static void __exit twl4030_rtc_exit(void) -{ - platform_driver_unregister(&twl4030rtc_driver); -} -module_exit(twl4030_rtc_exit); - -MODULE_AUTHOR("Texas Instruments, MontaVista Software"); -MODULE_LICENSE("GPL"); diff --git a/drivers/usb/otg/twl4030-usb.c b/drivers/usb/otg/twl4030-usb.c index bd9883f..3acbdb8 100644 --- a/drivers/usb/otg/twl4030-usb.c +++ b/drivers/usb/otg/twl4030-usb.c @@ -33,7 +33,7 @@ #include #include #include -#include +#include #include #include diff --git a/drivers/video/omap/lcd_2430sdp.c b/drivers/video/omap/lcd_2430sdp.c index 760645d..3764a36 100644 --- a/drivers/video/omap/lcd_2430sdp.c +++ b/drivers/video/omap/lcd_2430sdp.c @@ -25,7 +25,7 @@ #include #include #include -#include +#include #include #include diff --git a/drivers/watchdog/twl4030_wdt.c b/drivers/watchdog/twl4030_wdt.c index cb46556..20968b2 100644 --- a/drivers/watchdog/twl4030_wdt.c +++ b/drivers/watchdog/twl4030_wdt.c @@ -26,7 +26,7 @@ #include #include #include -#include +#include #define TWL4030_WATCHDOG_CFG_REG_OFFS 0x3 diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h new file mode 100644 index 0000000..a50bcf8 --- /dev/null +++ b/include/linux/i2c/twl.h @@ -0,0 +1,550 @@ +/* + * twl4030.h - header for TWL4030 PM and audio CODEC device + * + * Copyright (C) 2005-2006 Texas Instruments, Inc. + * + * Based on tlv320aic23.c: + * Copyright (c) by Kai Svahn + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#ifndef __TWL4030_H_ +#define __TWL4030_H_ + +#include +#include + +/* + * Using the twl4030 core we address registers using a pair + * { module id, relative register offset } + * which that core then maps to the relevant + * { i2c slave, absolute register address } + * + * The module IDs are meaningful only to the twl4030 core code, + * which uses them as array indices to look up the first register + * address each module uses within a given i2c slave. + */ + +/* Slave 0 (i2c address 0x48) */ +#define TWL4030_MODULE_USB 0x00 + +/* Slave 1 (i2c address 0x49) */ +#define TWL4030_MODULE_AUDIO_VOICE 0x01 +#define TWL4030_MODULE_GPIO 0x02 +#define TWL4030_MODULE_INTBR 0x03 +#define TWL4030_MODULE_PIH 0x04 +#define TWL4030_MODULE_TEST 0x05 + +/* Slave 2 (i2c address 0x4a) */ +#define TWL4030_MODULE_KEYPAD 0x06 +#define TWL4030_MODULE_MADC 0x07 +#define TWL4030_MODULE_INTERRUPTS 0x08 +#define TWL4030_MODULE_LED 0x09 +#define TWL4030_MODULE_MAIN_CHARGE 0x0A +#define TWL4030_MODULE_PRECHARGE 0x0B +#define TWL4030_MODULE_PWM0 0x0C +#define TWL4030_MODULE_PWM1 0x0D +#define TWL4030_MODULE_PWMA 0x0E +#define TWL4030_MODULE_PWMB 0x0F + +#define TWL5031_MODULE_ACCESSORY 0x10 +#define TWL5031_MODULE_INTERRUPTS 0x11 + +/* Slave 3 (i2c address 0x4b) */ +#define TWL4030_MODULE_BACKUP 0x12 +#define TWL4030_MODULE_INT 0x13 +#define TWL4030_MODULE_PM_MASTER 0x14 +#define TWL4030_MODULE_PM_RECEIVER 0x15 +#define TWL4030_MODULE_RTC 0x16 +#define TWL4030_MODULE_SECURED_REG 0x17 + +/* + * Read and write single 8-bit registers + */ +int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg); +int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg); + +/* + * Read and write several 8-bit registers at once. + * + * IMPORTANT: For twl4030_i2c_write(), allocate num_bytes + 1 + * for the value, and populate your data starting at offset 1. + */ +int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); +int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); + +/*----------------------------------------------------------------------*/ + +/* + * NOTE: at up to 1024 registers, this is a big chip. + * + * Avoid putting register declarations in this file, instead of into + * a driver-private file, unless some of the registers in a block + * need to be shared with other drivers. One example is blocks that + * have Secondary IRQ Handler (SIH) registers. + */ + +#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0) +#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1) +#define TWL4030_SIH_CTRL_COR_MASK BIT(2) + +/*----------------------------------------------------------------------*/ + +/* + * GPIO Block Register offsets (use TWL4030_MODULE_GPIO) + */ + +#define REG_GPIODATAIN1 0x0 +#define REG_GPIODATAIN2 0x1 +#define REG_GPIODATAIN3 0x2 +#define REG_GPIODATADIR1 0x3 +#define REG_GPIODATADIR2 0x4 +#define REG_GPIODATADIR3 0x5 +#define REG_GPIODATAOUT1 0x6 +#define REG_GPIODATAOUT2 0x7 +#define REG_GPIODATAOUT3 0x8 +#define REG_CLEARGPIODATAOUT1 0x9 +#define REG_CLEARGPIODATAOUT2 0xA +#define REG_CLEARGPIODATAOUT3 0xB +#define REG_SETGPIODATAOUT1 0xC +#define REG_SETGPIODATAOUT2 0xD +#define REG_SETGPIODATAOUT3 0xE +#define REG_GPIO_DEBEN1 0xF +#define REG_GPIO_DEBEN2 0x10 +#define REG_GPIO_DEBEN3 0x11 +#define REG_GPIO_CTRL 0x12 +#define REG_GPIOPUPDCTR1 0x13 +#define REG_GPIOPUPDCTR2 0x14 +#define REG_GPIOPUPDCTR3 0x15 +#define REG_GPIOPUPDCTR4 0x16 +#define REG_GPIOPUPDCTR5 0x17 +#define REG_GPIO_ISR1A 0x19 +#define REG_GPIO_ISR2A 0x1A +#define REG_GPIO_ISR3A 0x1B +#define REG_GPIO_IMR1A 0x1C +#define REG_GPIO_IMR2A 0x1D +#define REG_GPIO_IMR3A 0x1E +#define REG_GPIO_ISR1B 0x1F +#define REG_GPIO_ISR2B 0x20 +#define REG_GPIO_ISR3B 0x21 +#define REG_GPIO_IMR1B 0x22 +#define REG_GPIO_IMR2B 0x23 +#define REG_GPIO_IMR3B 0x24 +#define REG_GPIO_EDR1 0x28 +#define REG_GPIO_EDR2 0x29 +#define REG_GPIO_EDR3 0x2A +#define REG_GPIO_EDR4 0x2B +#define REG_GPIO_EDR5 0x2C +#define REG_GPIO_SIH_CTRL 0x2D + +/* Up to 18 signals are available as GPIOs, when their + * pins are not assigned to another use (such as ULPI/USB). + */ +#define TWL4030_GPIO_MAX 18 + +/*----------------------------------------------------------------------*/ + +/* + * Keypad register offsets (use TWL4030_MODULE_KEYPAD) + * ... SIH/interrupt only + */ + +#define TWL4030_KEYPAD_KEYP_ISR1 0x11 +#define TWL4030_KEYPAD_KEYP_IMR1 0x12 +#define TWL4030_KEYPAD_KEYP_ISR2 0x13 +#define TWL4030_KEYPAD_KEYP_IMR2 0x14 +#define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */ +#define TWL4030_KEYPAD_KEYP_EDR 0x16 +#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17 + +/*----------------------------------------------------------------------*/ + +/* + * Multichannel ADC register offsets (use TWL4030_MODULE_MADC) + * ... SIH/interrupt only + */ + +#define TWL4030_MADC_ISR1 0x61 +#define TWL4030_MADC_IMR1 0x62 +#define TWL4030_MADC_ISR2 0x63 +#define TWL4030_MADC_IMR2 0x64 +#define TWL4030_MADC_SIR 0x65 /* test register */ +#define TWL4030_MADC_EDR 0x66 +#define TWL4030_MADC_SIH_CTRL 0x67 + +/*----------------------------------------------------------------------*/ + +/* + * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS) + */ + +#define TWL4030_INTERRUPTS_BCIISR1A 0x0 +#define TWL4030_INTERRUPTS_BCIISR2A 0x1 +#define TWL4030_INTERRUPTS_BCIIMR1A 0x2 +#define TWL4030_INTERRUPTS_BCIIMR2A 0x3 +#define TWL4030_INTERRUPTS_BCIISR1B 0x4 +#define TWL4030_INTERRUPTS_BCIISR2B 0x5 +#define TWL4030_INTERRUPTS_BCIIMR1B 0x6 +#define TWL4030_INTERRUPTS_BCIIMR2B 0x7 +#define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */ +#define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */ +#define TWL4030_INTERRUPTS_BCIEDR1 0xa +#define TWL4030_INTERRUPTS_BCIEDR2 0xb +#define TWL4030_INTERRUPTS_BCIEDR3 0xc +#define TWL4030_INTERRUPTS_BCISIHCTRL 0xd + +/*----------------------------------------------------------------------*/ + +/* + * Power Interrupt block register offsets (use TWL4030_MODULE_INT) + */ + +#define TWL4030_INT_PWR_ISR1 0x0 +#define TWL4030_INT_PWR_IMR1 0x1 +#define TWL4030_INT_PWR_ISR2 0x2 +#define TWL4030_INT_PWR_IMR2 0x3 +#define TWL4030_INT_PWR_SIR 0x4 /* test register */ +#define TWL4030_INT_PWR_EDR1 0x5 +#define TWL4030_INT_PWR_EDR2 0x6 +#define TWL4030_INT_PWR_SIH_CTRL 0x7 + +/*----------------------------------------------------------------------*/ + +/* + * Accessory Interrupts + */ +#define TWL5031_ACIIMR_LSB 0x05 +#define TWL5031_ACIIMR_MSB 0x06 +#define TWL5031_ACIIDR_LSB 0x07 +#define TWL5031_ACIIDR_MSB 0x08 +#define TWL5031_ACCISR1 0x0F +#define TWL5031_ACCIMR1 0x10 +#define TWL5031_ACCISR2 0x11 +#define TWL5031_ACCIMR2 0x12 +#define TWL5031_ACCSIR 0x13 +#define TWL5031_ACCEDR1 0x14 +#define TWL5031_ACCSIHCTRL 0x15 + +/*----------------------------------------------------------------------*/ + +/* + * Battery Charger Controller + */ + +#define TWL5031_INTERRUPTS_BCIISR1 0x0 +#define TWL5031_INTERRUPTS_BCIIMR1 0x1 +#define TWL5031_INTERRUPTS_BCIISR2 0x2 +#define TWL5031_INTERRUPTS_BCIIMR2 0x3 +#define TWL5031_INTERRUPTS_BCISIR 0x4 +#define TWL5031_INTERRUPTS_BCIEDR1 0x5 +#define TWL5031_INTERRUPTS_BCIEDR2 0x6 +#define TWL5031_INTERRUPTS_BCISIHCTRL 0x7 + +/*----------------------------------------------------------------------*/ + +/* Power bus message definitions */ + +/* The TWL4030/5030 splits its power-management resources (the various + * regulators, clock and reset lines) into 3 processor groups - P1, P2 and + * P3. These groups can then be configured to transition between sleep, wait-on + * and active states by sending messages to the power bus. See Section 5.4.2 + * Power Resources of TWL4030 TRM + */ + +/* Processor groups */ +#define DEV_GRP_NULL 0x0 +#define DEV_GRP_P1 0x1 /* P1: all OMAP devices */ +#define DEV_GRP_P2 0x2 /* P2: all Modem devices */ +#define DEV_GRP_P3 0x4 /* P3: all peripheral devices */ + +/* Resource groups */ +#define RES_GRP_RES 0x0 /* Reserved */ +#define RES_GRP_PP 0x1 /* Power providers */ +#define RES_GRP_RC 0x2 /* Reset and control */ +#define RES_GRP_PP_RC 0x3 +#define RES_GRP_PR 0x4 /* Power references */ +#define RES_GRP_PP_PR 0x5 +#define RES_GRP_RC_PR 0x6 +#define RES_GRP_ALL 0x7 /* All resource groups */ + +#define RES_TYPE2_R0 0x0 + +#define RES_TYPE_ALL 0x7 + +/* Resource states */ +#define RES_STATE_WRST 0xF +#define RES_STATE_ACTIVE 0xE +#define RES_STATE_SLEEP 0x8 +#define RES_STATE_OFF 0x0 + +/* Power resources */ + +/* Power providers */ +#define RES_VAUX1 1 +#define RES_VAUX2 2 +#define RES_VAUX3 3 +#define RES_VAUX4 4 +#define RES_VMMC1 5 +#define RES_VMMC2 6 +#define RES_VPLL1 7 +#define RES_VPLL2 8 +#define RES_VSIM 9 +#define RES_VDAC 10 +#define RES_VINTANA1 11 +#define RES_VINTANA2 12 +#define RES_VINTDIG 13 +#define RES_VIO 14 +#define RES_VDD1 15 +#define RES_VDD2 16 +#define RES_VUSB_1V5 17 +#define RES_VUSB_1V8 18 +#define RES_VUSB_3V1 19 +#define RES_VUSBCP 20 +#define RES_REGEN 21 +/* Reset and control */ +#define RES_NRES_PWRON 22 +#define RES_CLKEN 23 +#define RES_SYSEN 24 +#define RES_HFCLKOUT 25 +#define RES_32KCLKOUT 26 +#define RES_RESET 27 +/* Power Reference */ +#define RES_Main_Ref 28 + +#define TOTAL_RESOURCES 28 +/* + * Power Bus Message Format ... these can be sent individually by Linux, + * but are usually part of downloaded scripts that are run when various + * power events are triggered. + * + * Broadcast Message (16 Bits): + * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4] + * RES_STATE[3:0] + * + * Singular Message (16 Bits): + * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0] + */ + +#define MSG_BROADCAST(devgrp, grp, type, type2, state) \ + ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \ + | (type) << 4 | (state)) + +#define MSG_SINGULAR(devgrp, id, state) \ + ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state)) + +/*----------------------------------------------------------------------*/ + +struct twl4030_clock_init_data { + bool ck32k_lowpwr_enable; +}; + +struct twl4030_bci_platform_data { + int *battery_tmp_tbl; + unsigned int tblsize; +}; + +/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */ +struct twl4030_gpio_platform_data { + int gpio_base; + unsigned irq_base, irq_end; + + /* package the two LED signals as output-only GPIOs? */ + bool use_leds; + + /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */ + u8 mmc_cd; + + /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */ + u32 debounce; + + /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup + * should be enabled. Else, if that bit is set in "pulldowns", + * that pulldown is enabled. Don't waste power by letting any + * digital inputs float... + */ + u32 pullups; + u32 pulldowns; + + int (*setup)(struct device *dev, + unsigned gpio, unsigned ngpio); + int (*teardown)(struct device *dev, + unsigned gpio, unsigned ngpio); +}; + +struct twl4030_madc_platform_data { + int irq_line; +}; + +/* Boards have uniqe mappings of {row, col} --> keycode. + * Column and row are 8 bits each, but range only from 0..7. + * a PERSISTENT_KEY is "always on" and never reported. + */ +#define PERSISTENT_KEY(r, c) KEY((r), (c), KEY_RESERVED) + +struct twl4030_keypad_data { + const struct matrix_keymap_data *keymap_data; + unsigned rows; + unsigned cols; + bool rep; +}; + +enum twl4030_usb_mode { + T2_USB_MODE_ULPI = 1, + T2_USB_MODE_CEA2011_3PIN = 2, +}; + +struct twl4030_usb_data { + enum twl4030_usb_mode usb_mode; +}; + +struct twl4030_ins { + u16 pmb_message; + u8 delay; +}; + +struct twl4030_script { + struct twl4030_ins *script; + unsigned size; + u8 flags; +#define TWL4030_WRST_SCRIPT (1<<0) +#define TWL4030_WAKEUP12_SCRIPT (1<<1) +#define TWL4030_WAKEUP3_SCRIPT (1<<2) +#define TWL4030_SLEEP_SCRIPT (1<<3) +}; + +struct twl4030_resconfig { + u8 resource; + u8 devgroup; /* Processor group that Power resource belongs to */ + u8 type; /* Power resource addressed, 6 / broadcast message */ + u8 type2; /* Power resource addressed, 3 / broadcast message */ + u8 remap_off; /* off state remapping */ + u8 remap_sleep; /* sleep state remapping */ +}; + +struct twl4030_power_data { + struct twl4030_script **scripts; + unsigned num; + struct twl4030_resconfig *resource_config; +#define TWL4030_RESCONFIG_UNDEF ((u8)-1) +}; + +extern void twl4030_power_init(struct twl4030_power_data *triton2_scripts); + +struct twl4030_codec_audio_data { + unsigned int audio_mclk; + unsigned int ramp_delay_value; + unsigned int hs_extmute:1; + void (*set_hs_extmute)(int mute); +}; + +struct twl4030_codec_vibra_data { + unsigned int audio_mclk; + unsigned int coexist; +}; + +struct twl4030_codec_data { + unsigned int audio_mclk; + struct twl4030_codec_audio_data *audio; + struct twl4030_codec_vibra_data *vibra; +}; + +struct twl4030_platform_data { + unsigned irq_base, irq_end; + struct twl4030_clock_init_data *clock; + struct twl4030_bci_platform_data *bci; + struct twl4030_gpio_platform_data *gpio; + struct twl4030_madc_platform_data *madc; + struct twl4030_keypad_data *keypad; + struct twl4030_usb_data *usb; + struct twl4030_power_data *power; + struct twl4030_codec_data *codec; + + /* LDO regulators */ + struct regulator_init_data *vdac; + struct regulator_init_data *vpll1; + struct regulator_init_data *vpll2; + struct regulator_init_data *vmmc1; + struct regulator_init_data *vmmc2; + struct regulator_init_data *vsim; + struct regulator_init_data *vaux1; + struct regulator_init_data *vaux2; + struct regulator_init_data *vaux3; + struct regulator_init_data *vaux4; + struct regulator_init_data *vio; + struct regulator_init_data *vdd1; + struct regulator_init_data *vdd2; + struct regulator_init_data *vintana1; + struct regulator_init_data *vintana2; + struct regulator_init_data *vintdig; +}; + +/*----------------------------------------------------------------------*/ + +int twl4030_sih_setup(int module); + +/* Offsets to Power Registers */ +#define TWL4030_VDAC_DEV_GRP 0x3B +#define TWL4030_VDAC_DEDICATED 0x3E +#define TWL4030_VAUX1_DEV_GRP 0x17 +#define TWL4030_VAUX1_DEDICATED 0x1A +#define TWL4030_VAUX2_DEV_GRP 0x1B +#define TWL4030_VAUX2_DEDICATED 0x1E +#define TWL4030_VAUX3_DEV_GRP 0x1F +#define TWL4030_VAUX3_DEDICATED 0x22 + +#if defined(CONFIG_TWL4030_BCI_BATTERY) || \ + defined(CONFIG_TWL4030_BCI_BATTERY_MODULE) + extern int twl4030charger_usb_en(int enable); +#else + static inline int twl4030charger_usb_en(int enable) { return 0; } +#endif + +/*----------------------------------------------------------------------*/ + +/* Linux-specific regulator identifiers ... for now, we only support + * the LDOs, and leave the three buck converters alone. VDD1 and VDD2 + * need to tie into hardware based voltage scaling (cpufreq etc), while + * VIO is generally fixed. + */ + +/* EXTERNAL dc-to-dc buck converters */ +#define TWL4030_REG_VDD1 0 +#define TWL4030_REG_VDD2 1 +#define TWL4030_REG_VIO 2 + +/* EXTERNAL LDOs */ +#define TWL4030_REG_VDAC 3 +#define TWL4030_REG_VPLL1 4 +#define TWL4030_REG_VPLL2 5 /* not on all chips */ +#define TWL4030_REG_VMMC1 6 +#define TWL4030_REG_VMMC2 7 /* not on all chips */ +#define TWL4030_REG_VSIM 8 /* not on all chips */ +#define TWL4030_REG_VAUX1 9 /* not on all chips */ +#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */ +#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */ +#define TWL4030_REG_VAUX3 12 /* not on all chips */ +#define TWL4030_REG_VAUX4 13 /* not on all chips */ + +/* INTERNAL LDOs */ +#define TWL4030_REG_VINTANA1 14 +#define TWL4030_REG_VINTANA2 15 +#define TWL4030_REG_VINTDIG 16 +#define TWL4030_REG_VUSB1V5 17 +#define TWL4030_REG_VUSB1V8 18 +#define TWL4030_REG_VUSB3V1 19 + +#endif /* End of __TWL4030_H */ diff --git a/include/linux/i2c/twl4030.h b/include/linux/i2c/twl4030.h deleted file mode 100644 index a50bcf8..0000000 --- a/include/linux/i2c/twl4030.h +++ /dev/null @@ -1,550 +0,0 @@ -/* - * twl4030.h - header for TWL4030 PM and audio CODEC device - * - * Copyright (C) 2005-2006 Texas Instruments, Inc. - * - * Based on tlv320aic23.c: - * Copyright (c) by Kai Svahn - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#ifndef __TWL4030_H_ -#define __TWL4030_H_ - -#include -#include - -/* - * Using the twl4030 core we address registers using a pair - * { module id, relative register offset } - * which that core then maps to the relevant - * { i2c slave, absolute register address } - * - * The module IDs are meaningful only to the twl4030 core code, - * which uses them as array indices to look up the first register - * address each module uses within a given i2c slave. - */ - -/* Slave 0 (i2c address 0x48) */ -#define TWL4030_MODULE_USB 0x00 - -/* Slave 1 (i2c address 0x49) */ -#define TWL4030_MODULE_AUDIO_VOICE 0x01 -#define TWL4030_MODULE_GPIO 0x02 -#define TWL4030_MODULE_INTBR 0x03 -#define TWL4030_MODULE_PIH 0x04 -#define TWL4030_MODULE_TEST 0x05 - -/* Slave 2 (i2c address 0x4a) */ -#define TWL4030_MODULE_KEYPAD 0x06 -#define TWL4030_MODULE_MADC 0x07 -#define TWL4030_MODULE_INTERRUPTS 0x08 -#define TWL4030_MODULE_LED 0x09 -#define TWL4030_MODULE_MAIN_CHARGE 0x0A -#define TWL4030_MODULE_PRECHARGE 0x0B -#define TWL4030_MODULE_PWM0 0x0C -#define TWL4030_MODULE_PWM1 0x0D -#define TWL4030_MODULE_PWMA 0x0E -#define TWL4030_MODULE_PWMB 0x0F - -#define TWL5031_MODULE_ACCESSORY 0x10 -#define TWL5031_MODULE_INTERRUPTS 0x11 - -/* Slave 3 (i2c address 0x4b) */ -#define TWL4030_MODULE_BACKUP 0x12 -#define TWL4030_MODULE_INT 0x13 -#define TWL4030_MODULE_PM_MASTER 0x14 -#define TWL4030_MODULE_PM_RECEIVER 0x15 -#define TWL4030_MODULE_RTC 0x16 -#define TWL4030_MODULE_SECURED_REG 0x17 - -/* - * Read and write single 8-bit registers - */ -int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg); -int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg); - -/* - * Read and write several 8-bit registers at once. - * - * IMPORTANT: For twl4030_i2c_write(), allocate num_bytes + 1 - * for the value, and populate your data starting at offset 1. - */ -int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); -int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); - -/*----------------------------------------------------------------------*/ - -/* - * NOTE: at up to 1024 registers, this is a big chip. - * - * Avoid putting register declarations in this file, instead of into - * a driver-private file, unless some of the registers in a block - * need to be shared with other drivers. One example is blocks that - * have Secondary IRQ Handler (SIH) registers. - */ - -#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0) -#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1) -#define TWL4030_SIH_CTRL_COR_MASK BIT(2) - -/*----------------------------------------------------------------------*/ - -/* - * GPIO Block Register offsets (use TWL4030_MODULE_GPIO) - */ - -#define REG_GPIODATAIN1 0x0 -#define REG_GPIODATAIN2 0x1 -#define REG_GPIODATAIN3 0x2 -#define REG_GPIODATADIR1 0x3 -#define REG_GPIODATADIR2 0x4 -#define REG_GPIODATADIR3 0x5 -#define REG_GPIODATAOUT1 0x6 -#define REG_GPIODATAOUT2 0x7 -#define REG_GPIODATAOUT3 0x8 -#define REG_CLEARGPIODATAOUT1 0x9 -#define REG_CLEARGPIODATAOUT2 0xA -#define REG_CLEARGPIODATAOUT3 0xB -#define REG_SETGPIODATAOUT1 0xC -#define REG_SETGPIODATAOUT2 0xD -#define REG_SETGPIODATAOUT3 0xE -#define REG_GPIO_DEBEN1 0xF -#define REG_GPIO_DEBEN2 0x10 -#define REG_GPIO_DEBEN3 0x11 -#define REG_GPIO_CTRL 0x12 -#define REG_GPIOPUPDCTR1 0x13 -#define REG_GPIOPUPDCTR2 0x14 -#define REG_GPIOPUPDCTR3 0x15 -#define REG_GPIOPUPDCTR4 0x16 -#define REG_GPIOPUPDCTR5 0x17 -#define REG_GPIO_ISR1A 0x19 -#define REG_GPIO_ISR2A 0x1A -#define REG_GPIO_ISR3A 0x1B -#define REG_GPIO_IMR1A 0x1C -#define REG_GPIO_IMR2A 0x1D -#define REG_GPIO_IMR3A 0x1E -#define REG_GPIO_ISR1B 0x1F -#define REG_GPIO_ISR2B 0x20 -#define REG_GPIO_ISR3B 0x21 -#define REG_GPIO_IMR1B 0x22 -#define REG_GPIO_IMR2B 0x23 -#define REG_GPIO_IMR3B 0x24 -#define REG_GPIO_EDR1 0x28 -#define REG_GPIO_EDR2 0x29 -#define REG_GPIO_EDR3 0x2A -#define REG_GPIO_EDR4 0x2B -#define REG_GPIO_EDR5 0x2C -#define REG_GPIO_SIH_CTRL 0x2D - -/* Up to 18 signals are available as GPIOs, when their - * pins are not assigned to another use (such as ULPI/USB). - */ -#define TWL4030_GPIO_MAX 18 - -/*----------------------------------------------------------------------*/ - -/* - * Keypad register offsets (use TWL4030_MODULE_KEYPAD) - * ... SIH/interrupt only - */ - -#define TWL4030_KEYPAD_KEYP_ISR1 0x11 -#define TWL4030_KEYPAD_KEYP_IMR1 0x12 -#define TWL4030_KEYPAD_KEYP_ISR2 0x13 -#define TWL4030_KEYPAD_KEYP_IMR2 0x14 -#define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */ -#define TWL4030_KEYPAD_KEYP_EDR 0x16 -#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17 - -/*----------------------------------------------------------------------*/ - -/* - * Multichannel ADC register offsets (use TWL4030_MODULE_MADC) - * ... SIH/interrupt only - */ - -#define TWL4030_MADC_ISR1 0x61 -#define TWL4030_MADC_IMR1 0x62 -#define TWL4030_MADC_ISR2 0x63 -#define TWL4030_MADC_IMR2 0x64 -#define TWL4030_MADC_SIR 0x65 /* test register */ -#define TWL4030_MADC_EDR 0x66 -#define TWL4030_MADC_SIH_CTRL 0x67 - -/*----------------------------------------------------------------------*/ - -/* - * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS) - */ - -#define TWL4030_INTERRUPTS_BCIISR1A 0x0 -#define TWL4030_INTERRUPTS_BCIISR2A 0x1 -#define TWL4030_INTERRUPTS_BCIIMR1A 0x2 -#define TWL4030_INTERRUPTS_BCIIMR2A 0x3 -#define TWL4030_INTERRUPTS_BCIISR1B 0x4 -#define TWL4030_INTERRUPTS_BCIISR2B 0x5 -#define TWL4030_INTERRUPTS_BCIIMR1B 0x6 -#define TWL4030_INTERRUPTS_BCIIMR2B 0x7 -#define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */ -#define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */ -#define TWL4030_INTERRUPTS_BCIEDR1 0xa -#define TWL4030_INTERRUPTS_BCIEDR2 0xb -#define TWL4030_INTERRUPTS_BCIEDR3 0xc -#define TWL4030_INTERRUPTS_BCISIHCTRL 0xd - -/*----------------------------------------------------------------------*/ - -/* - * Power Interrupt block register offsets (use TWL4030_MODULE_INT) - */ - -#define TWL4030_INT_PWR_ISR1 0x0 -#define TWL4030_INT_PWR_IMR1 0x1 -#define TWL4030_INT_PWR_ISR2 0x2 -#define TWL4030_INT_PWR_IMR2 0x3 -#define TWL4030_INT_PWR_SIR 0x4 /* test register */ -#define TWL4030_INT_PWR_EDR1 0x5 -#define TWL4030_INT_PWR_EDR2 0x6 -#define TWL4030_INT_PWR_SIH_CTRL 0x7 - -/*----------------------------------------------------------------------*/ - -/* - * Accessory Interrupts - */ -#define TWL5031_ACIIMR_LSB 0x05 -#define TWL5031_ACIIMR_MSB 0x06 -#define TWL5031_ACIIDR_LSB 0x07 -#define TWL5031_ACIIDR_MSB 0x08 -#define TWL5031_ACCISR1 0x0F -#define TWL5031_ACCIMR1 0x10 -#define TWL5031_ACCISR2 0x11 -#define TWL5031_ACCIMR2 0x12 -#define TWL5031_ACCSIR 0x13 -#define TWL5031_ACCEDR1 0x14 -#define TWL5031_ACCSIHCTRL 0x15 - -/*----------------------------------------------------------------------*/ - -/* - * Battery Charger Controller - */ - -#define TWL5031_INTERRUPTS_BCIISR1 0x0 -#define TWL5031_INTERRUPTS_BCIIMR1 0x1 -#define TWL5031_INTERRUPTS_BCIISR2 0x2 -#define TWL5031_INTERRUPTS_BCIIMR2 0x3 -#define TWL5031_INTERRUPTS_BCISIR 0x4 -#define TWL5031_INTERRUPTS_BCIEDR1 0x5 -#define TWL5031_INTERRUPTS_BCIEDR2 0x6 -#define TWL5031_INTERRUPTS_BCISIHCTRL 0x7 - -/*----------------------------------------------------------------------*/ - -/* Power bus message definitions */ - -/* The TWL4030/5030 splits its power-management resources (the various - * regulators, clock and reset lines) into 3 processor groups - P1, P2 and - * P3. These groups can then be configured to transition between sleep, wait-on - * and active states by sending messages to the power bus. See Section 5.4.2 - * Power Resources of TWL4030 TRM - */ - -/* Processor groups */ -#define DEV_GRP_NULL 0x0 -#define DEV_GRP_P1 0x1 /* P1: all OMAP devices */ -#define DEV_GRP_P2 0x2 /* P2: all Modem devices */ -#define DEV_GRP_P3 0x4 /* P3: all peripheral devices */ - -/* Resource groups */ -#define RES_GRP_RES 0x0 /* Reserved */ -#define RES_GRP_PP 0x1 /* Power providers */ -#define RES_GRP_RC 0x2 /* Reset and control */ -#define RES_GRP_PP_RC 0x3 -#define RES_GRP_PR 0x4 /* Power references */ -#define RES_GRP_PP_PR 0x5 -#define RES_GRP_RC_PR 0x6 -#define RES_GRP_ALL 0x7 /* All resource groups */ - -#define RES_TYPE2_R0 0x0 - -#define RES_TYPE_ALL 0x7 - -/* Resource states */ -#define RES_STATE_WRST 0xF -#define RES_STATE_ACTIVE 0xE -#define RES_STATE_SLEEP 0x8 -#define RES_STATE_OFF 0x0 - -/* Power resources */ - -/* Power providers */ -#define RES_VAUX1 1 -#define RES_VAUX2 2 -#define RES_VAUX3 3 -#define RES_VAUX4 4 -#define RES_VMMC1 5 -#define RES_VMMC2 6 -#define RES_VPLL1 7 -#define RES_VPLL2 8 -#define RES_VSIM 9 -#define RES_VDAC 10 -#define RES_VINTANA1 11 -#define RES_VINTANA2 12 -#define RES_VINTDIG 13 -#define RES_VIO 14 -#define RES_VDD1 15 -#define RES_VDD2 16 -#define RES_VUSB_1V5 17 -#define RES_VUSB_1V8 18 -#define RES_VUSB_3V1 19 -#define RES_VUSBCP 20 -#define RES_REGEN 21 -/* Reset and control */ -#define RES_NRES_PWRON 22 -#define RES_CLKEN 23 -#define RES_SYSEN 24 -#define RES_HFCLKOUT 25 -#define RES_32KCLKOUT 26 -#define RES_RESET 27 -/* Power Reference */ -#define RES_Main_Ref 28 - -#define TOTAL_RESOURCES 28 -/* - * Power Bus Message Format ... these can be sent individually by Linux, - * but are usually part of downloaded scripts that are run when various - * power events are triggered. - * - * Broadcast Message (16 Bits): - * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4] - * RES_STATE[3:0] - * - * Singular Message (16 Bits): - * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0] - */ - -#define MSG_BROADCAST(devgrp, grp, type, type2, state) \ - ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \ - | (type) << 4 | (state)) - -#define MSG_SINGULAR(devgrp, id, state) \ - ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state)) - -/*----------------------------------------------------------------------*/ - -struct twl4030_clock_init_data { - bool ck32k_lowpwr_enable; -}; - -struct twl4030_bci_platform_data { - int *battery_tmp_tbl; - unsigned int tblsize; -}; - -/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */ -struct twl4030_gpio_platform_data { - int gpio_base; - unsigned irq_base, irq_end; - - /* package the two LED signals as output-only GPIOs? */ - bool use_leds; - - /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */ - u8 mmc_cd; - - /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */ - u32 debounce; - - /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup - * should be enabled. Else, if that bit is set in "pulldowns", - * that pulldown is enabled. Don't waste power by letting any - * digital inputs float... - */ - u32 pullups; - u32 pulldowns; - - int (*setup)(struct device *dev, - unsigned gpio, unsigned ngpio); - int (*teardown)(struct device *dev, - unsigned gpio, unsigned ngpio); -}; - -struct twl4030_madc_platform_data { - int irq_line; -}; - -/* Boards have uniqe mappings of {row, col} --> keycode. - * Column and row are 8 bits each, but range only from 0..7. - * a PERSISTENT_KEY is "always on" and never reported. - */ -#define PERSISTENT_KEY(r, c) KEY((r), (c), KEY_RESERVED) - -struct twl4030_keypad_data { - const struct matrix_keymap_data *keymap_data; - unsigned rows; - unsigned cols; - bool rep; -}; - -enum twl4030_usb_mode { - T2_USB_MODE_ULPI = 1, - T2_USB_MODE_CEA2011_3PIN = 2, -}; - -struct twl4030_usb_data { - enum twl4030_usb_mode usb_mode; -}; - -struct twl4030_ins { - u16 pmb_message; - u8 delay; -}; - -struct twl4030_script { - struct twl4030_ins *script; - unsigned size; - u8 flags; -#define TWL4030_WRST_SCRIPT (1<<0) -#define TWL4030_WAKEUP12_SCRIPT (1<<1) -#define TWL4030_WAKEUP3_SCRIPT (1<<2) -#define TWL4030_SLEEP_SCRIPT (1<<3) -}; - -struct twl4030_resconfig { - u8 resource; - u8 devgroup; /* Processor group that Power resource belongs to */ - u8 type; /* Power resource addressed, 6 / broadcast message */ - u8 type2; /* Power resource addressed, 3 / broadcast message */ - u8 remap_off; /* off state remapping */ - u8 remap_sleep; /* sleep state remapping */ -}; - -struct twl4030_power_data { - struct twl4030_script **scripts; - unsigned num; - struct twl4030_resconfig *resource_config; -#define TWL4030_RESCONFIG_UNDEF ((u8)-1) -}; - -extern void twl4030_power_init(struct twl4030_power_data *triton2_scripts); - -struct twl4030_codec_audio_data { - unsigned int audio_mclk; - unsigned int ramp_delay_value; - unsigned int hs_extmute:1; - void (*set_hs_extmute)(int mute); -}; - -struct twl4030_codec_vibra_data { - unsigned int audio_mclk; - unsigned int coexist; -}; - -struct twl4030_codec_data { - unsigned int audio_mclk; - struct twl4030_codec_audio_data *audio; - struct twl4030_codec_vibra_data *vibra; -}; - -struct twl4030_platform_data { - unsigned irq_base, irq_end; - struct twl4030_clock_init_data *clock; - struct twl4030_bci_platform_data *bci; - struct twl4030_gpio_platform_data *gpio; - struct twl4030_madc_platform_data *madc; - struct twl4030_keypad_data *keypad; - struct twl4030_usb_data *usb; - struct twl4030_power_data *power; - struct twl4030_codec_data *codec; - - /* LDO regulators */ - struct regulator_init_data *vdac; - struct regulator_init_data *vpll1; - struct regulator_init_data *vpll2; - struct regulator_init_data *vmmc1; - struct regulator_init_data *vmmc2; - struct regulator_init_data *vsim; - struct regulator_init_data *vaux1; - struct regulator_init_data *vaux2; - struct regulator_init_data *vaux3; - struct regulator_init_data *vaux4; - struct regulator_init_data *vio; - struct regulator_init_data *vdd1; - struct regulator_init_data *vdd2; - struct regulator_init_data *vintana1; - struct regulator_init_data *vintana2; - struct regulator_init_data *vintdig; -}; - -/*----------------------------------------------------------------------*/ - -int twl4030_sih_setup(int module); - -/* Offsets to Power Registers */ -#define TWL4030_VDAC_DEV_GRP 0x3B -#define TWL4030_VDAC_DEDICATED 0x3E -#define TWL4030_VAUX1_DEV_GRP 0x17 -#define TWL4030_VAUX1_DEDICATED 0x1A -#define TWL4030_VAUX2_DEV_GRP 0x1B -#define TWL4030_VAUX2_DEDICATED 0x1E -#define TWL4030_VAUX3_DEV_GRP 0x1F -#define TWL4030_VAUX3_DEDICATED 0x22 - -#if defined(CONFIG_TWL4030_BCI_BATTERY) || \ - defined(CONFIG_TWL4030_BCI_BATTERY_MODULE) - extern int twl4030charger_usb_en(int enable); -#else - static inline int twl4030charger_usb_en(int enable) { return 0; } -#endif - -/*----------------------------------------------------------------------*/ - -/* Linux-specific regulator identifiers ... for now, we only support - * the LDOs, and leave the three buck converters alone. VDD1 and VDD2 - * need to tie into hardware based voltage scaling (cpufreq etc), while - * VIO is generally fixed. - */ - -/* EXTERNAL dc-to-dc buck converters */ -#define TWL4030_REG_VDD1 0 -#define TWL4030_REG_VDD2 1 -#define TWL4030_REG_VIO 2 - -/* EXTERNAL LDOs */ -#define TWL4030_REG_VDAC 3 -#define TWL4030_REG_VPLL1 4 -#define TWL4030_REG_VPLL2 5 /* not on all chips */ -#define TWL4030_REG_VMMC1 6 -#define TWL4030_REG_VMMC2 7 /* not on all chips */ -#define TWL4030_REG_VSIM 8 /* not on all chips */ -#define TWL4030_REG_VAUX1 9 /* not on all chips */ -#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */ -#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */ -#define TWL4030_REG_VAUX3 12 /* not on all chips */ -#define TWL4030_REG_VAUX4 13 /* not on all chips */ - -/* INTERNAL LDOs */ -#define TWL4030_REG_VINTANA1 14 -#define TWL4030_REG_VINTANA2 15 -#define TWL4030_REG_VINTDIG 16 -#define TWL4030_REG_VUSB1V5 17 -#define TWL4030_REG_VUSB1V8 18 -#define TWL4030_REG_VUSB3V1 19 - -#endif /* End of __TWL4030_H */ diff --git a/sound/soc/codecs/twl4030.c b/sound/soc/codecs/twl4030.c index 5f1681f..c3a6ceb 100644 --- a/sound/soc/codecs/twl4030.c +++ b/sound/soc/codecs/twl4030.c @@ -26,7 +26,7 @@ #include #include #include -#include +#include #include #include #include -- cgit v0.10.2