From d5dc9ac3f6daf7df45c49e5a861c733a5f794c6b Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 6 Jan 2011 23:01:02 -0800 Subject: Input: ad7879 - convert I2C to dev_pm_ops There is a general move towards the use of dev_pm_ops rather than bus specific suspend APIs as this simplifies both the bus and PM core implementations. Convert the ad7879-ts I2C support over. Compile tested only. Signed-off-by: Mark Brown Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/touchscreen/ad7879-i2c.c b/drivers/input/touchscreen/ad7879-i2c.c index d82a38e..4e4e58c 100644 --- a/drivers/input/touchscreen/ad7879-i2c.c +++ b/drivers/input/touchscreen/ad7879-i2c.c @@ -10,14 +10,16 @@ #include #include #include +#include #include "ad7879.h" #define AD7879_DEVID 0x79 /* AD7879-1/AD7889-1 */ #ifdef CONFIG_PM -static int ad7879_i2c_suspend(struct i2c_client *client, pm_message_t message) +static int ad7879_i2c_suspend(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct ad7879 *ts = i2c_get_clientdata(client); ad7879_suspend(ts); @@ -25,17 +27,17 @@ static int ad7879_i2c_suspend(struct i2c_client *client, pm_message_t message) return 0; } -static int ad7879_i2c_resume(struct i2c_client *client) +static int ad7879_i2c_resume(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct ad7879 *ts = i2c_get_clientdata(client); ad7879_resume(ts); return 0; } -#else -# define ad7879_i2c_suspend NULL -# define ad7879_i2c_resume NULL + +static SIMPLE_DEV_PM_OPS(ad7879_i2c_pm, ad7879_i2c_suspend, ad7879_i2c_resume); #endif /* All registers are word-sized. @@ -117,11 +119,12 @@ static struct i2c_driver ad7879_i2c_driver = { .driver = { .name = "ad7879", .owner = THIS_MODULE, +#ifdef CONFIG_PM + .pm = &ad7879_i2c_pm, +#endif }, .probe = ad7879_i2c_probe, .remove = __devexit_p(ad7879_i2c_remove), - .suspend = ad7879_i2c_suspend, - .resume = ad7879_i2c_resume, .id_table = ad7879_id, }; -- cgit v0.10.2 From 85012fff38302e0262f838431e853f8c09e754d5 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 6 Jan 2011 23:01:02 -0800 Subject: Input: eeti_ts - convert to dev_pm_ops There is a general move towards the use of dev_pm_ops rather than bus specific suspend APIs as this simplifies both the bus and PM core implementations. Convert the eeti_ts driver over. Compile tested only by me, but Sven Neumann reports that the new code works. Signed-off-by: Mark Brown Tested-by: Sven Neumann Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/touchscreen/eeti_ts.c b/drivers/input/touchscreen/eeti_ts.c index 7a3a916..7f8f538 100644 --- a/drivers/input/touchscreen/eeti_ts.c +++ b/drivers/input/touchscreen/eeti_ts.c @@ -261,8 +261,9 @@ static int __devexit eeti_ts_remove(struct i2c_client *client) } #ifdef CONFIG_PM -static int eeti_ts_suspend(struct i2c_client *client, pm_message_t mesg) +static int eeti_ts_suspend(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct eeti_ts_priv *priv = i2c_get_clientdata(client); struct input_dev *input_dev = priv->input; @@ -279,8 +280,9 @@ static int eeti_ts_suspend(struct i2c_client *client, pm_message_t mesg) return 0; } -static int eeti_ts_resume(struct i2c_client *client) +static int eeti_ts_resume(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct eeti_ts_priv *priv = i2c_get_clientdata(client); struct input_dev *input_dev = priv->input; @@ -296,9 +298,8 @@ static int eeti_ts_resume(struct i2c_client *client) return 0; } -#else -#define eeti_ts_suspend NULL -#define eeti_ts_resume NULL + +static SIMPLE_DEV_PM_OPS(eeti_ts_pm, eeti_ts_suspend, eeti_ts_resume); #endif static const struct i2c_device_id eeti_ts_id[] = { @@ -310,11 +311,12 @@ MODULE_DEVICE_TABLE(i2c, eeti_ts_id); static struct i2c_driver eeti_ts_driver = { .driver = { .name = "eeti_ts", +#ifdef CONFIG_PM + .pm = &eeti_ts_pm, +#endif }, .probe = eeti_ts_probe, .remove = __devexit_p(eeti_ts_remove), - .suspend = eeti_ts_suspend, - .resume = eeti_ts_resume, .id_table = eeti_ts_id, }; -- cgit v0.10.2 From 92b672e217ddf87e4181454f8200f0f06139cdbc Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 6 Jan 2011 23:01:03 -0800 Subject: Input: mcs5000_ts - convert to dev_pm_ops There is a general move towards the use of dev_pm_ops rather than bus specific suspend APIs as this simplifies both the bus and PM core implementations. Convert the mcs5000_ts driver over. Compile tested only. Signed-off-by: Mark Brown Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/touchscreen/mcs5000_ts.c b/drivers/input/touchscreen/mcs5000_ts.c index 6ee9940..2d84c80 100644 --- a/drivers/input/touchscreen/mcs5000_ts.c +++ b/drivers/input/touchscreen/mcs5000_ts.c @@ -261,25 +261,27 @@ static int __devexit mcs5000_ts_remove(struct i2c_client *client) } #ifdef CONFIG_PM -static int mcs5000_ts_suspend(struct i2c_client *client, pm_message_t mesg) +static int mcs5000_ts_suspend(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); + /* Touch sleep mode */ i2c_smbus_write_byte_data(client, MCS5000_TS_OP_MODE, OP_MODE_SLEEP); return 0; } -static int mcs5000_ts_resume(struct i2c_client *client) +static int mcs5000_ts_resume(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct mcs5000_ts_data *data = i2c_get_clientdata(client); mcs5000_ts_phys_init(data); return 0; } -#else -#define mcs5000_ts_suspend NULL -#define mcs5000_ts_resume NULL + +static SIMPLE_DEV_PM_OPS(mcs5000_ts_pm, mcs5000_ts_suspend, mcs5000_ts_resume); #endif static const struct i2c_device_id mcs5000_ts_id[] = { @@ -291,10 +293,11 @@ MODULE_DEVICE_TABLE(i2c, mcs5000_ts_id); static struct i2c_driver mcs5000_ts_driver = { .probe = mcs5000_ts_probe, .remove = __devexit_p(mcs5000_ts_remove), - .suspend = mcs5000_ts_suspend, - .resume = mcs5000_ts_resume, .driver = { .name = "mcs5000_ts", +#ifdef CONFIG_PM + .pm = &mcs5000_ts_pm, +#endif }, .id_table = mcs5000_ts_id, }; -- cgit v0.10.2 From d72e64ec0b134d26a89c736394ee0b638513bed8 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 6 Jan 2011 23:01:03 -0800 Subject: Input: migor_ts - convert to dev_pm_ops There is a general move towards the use of dev_pm_ops rather than bus specific suspend APIs as this simplifies both the bus and PM core implementations. Convert the migor_ts driver over. Compile tested only. Signed-off-by: Mark Brown Acked-by: Magnus Damm Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/touchscreen/migor_ts.c b/drivers/input/touchscreen/migor_ts.c index defe5dd..5803bd0 100644 --- a/drivers/input/touchscreen/migor_ts.c +++ b/drivers/input/touchscreen/migor_ts.c @@ -23,6 +23,7 @@ #include #include #include +#include #include #include #include @@ -226,8 +227,9 @@ static int migor_ts_remove(struct i2c_client *client) return 0; } -static int migor_ts_suspend(struct i2c_client *client, pm_message_t mesg) +static int migor_ts_suspend(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct migor_ts_priv *priv = dev_get_drvdata(&client->dev); if (device_may_wakeup(&client->dev)) @@ -236,8 +238,9 @@ static int migor_ts_suspend(struct i2c_client *client, pm_message_t mesg) return 0; } -static int migor_ts_resume(struct i2c_client *client) +static int migor_ts_resume(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct migor_ts_priv *priv = dev_get_drvdata(&client->dev); if (device_may_wakeup(&client->dev)) @@ -246,6 +249,8 @@ static int migor_ts_resume(struct i2c_client *client) return 0; } +static SIMPLE_DEV_PM_OPS(migor_ts_pm, migor_ts_suspend, migor_ts_resume); + static const struct i2c_device_id migor_ts_id[] = { { "migor_ts", 0 }, { } @@ -255,11 +260,10 @@ MODULE_DEVICE_TABLE(i2c, migor_ts); static struct i2c_driver migor_ts_driver = { .driver = { .name = "migor_ts", + .pm = &migor_ts_pm, }, .probe = migor_ts_probe, .remove = migor_ts_remove, - .suspend = migor_ts_suspend, - .resume = migor_ts_resume, .id_table = migor_ts_id, }; -- cgit v0.10.2 From 93f38e914183c9b7af248fab793153772996987c Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Thu, 6 Jan 2011 23:01:03 -0800 Subject: Input: cy8ctmg110_ts - Convert to dev_pm_ops There is a general move towards the use of dev_pm_ops rather than bus specific suspend APIs as this simplifies both the bus and PM core implementations. Convert the cy8ctmg110_ts driver over. Compile tested only. Signed-off-by: Mark Brown Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/touchscreen/cy8ctmg110_ts.c b/drivers/input/touchscreen/cy8ctmg110_ts.c index d0c3a72..a93c5c2 100644 --- a/drivers/input/touchscreen/cy8ctmg110_ts.c +++ b/drivers/input/touchscreen/cy8ctmg110_ts.c @@ -280,8 +280,9 @@ err_free_mem: } #ifdef CONFIG_PM -static int cy8ctmg110_suspend(struct i2c_client *client, pm_message_t mesg) +static int cy8ctmg110_suspend(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct cy8ctmg110 *ts = i2c_get_clientdata(client); if (device_may_wakeup(&client->dev)) @@ -293,8 +294,9 @@ static int cy8ctmg110_suspend(struct i2c_client *client, pm_message_t mesg) return 0; } -static int cy8ctmg110_resume(struct i2c_client *client) +static int cy8ctmg110_resume(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); struct cy8ctmg110 *ts = i2c_get_clientdata(client); if (device_may_wakeup(&client->dev)) @@ -305,6 +307,8 @@ static int cy8ctmg110_resume(struct i2c_client *client) } return 0; } + +static SIMPLE_DEV_PM_OPS(cy8ctmg110_pm, cy8ctmg110_suspend, cy8ctmg110_resume); #endif static int __devexit cy8ctmg110_remove(struct i2c_client *client) @@ -335,14 +339,13 @@ static struct i2c_driver cy8ctmg110_driver = { .driver = { .owner = THIS_MODULE, .name = CY8CTMG110_DRIVER_NAME, +#ifdef CONFIG_PM + .pm = &cy8ctmg110_pm, +#endif }, .id_table = cy8ctmg110_idtable, .probe = cy8ctmg110_probe, .remove = __devexit_p(cy8ctmg110_remove), -#ifdef CONFIG_PM - .suspend = cy8ctmg110_suspend, - .resume = cy8ctmg110_resume, -#endif }; static int __init cy8ctmg110_init(void) -- cgit v0.10.2 From f8313ef1f448006207f12c107123522c8bc00f15 Mon Sep 17 00:00:00 2001 From: Jiri Kosina Date: Sat, 8 Jan 2011 01:37:26 -0800 Subject: Input: i8042 - introduce 'notimeout' blacklist for Dell Vostro V13 i8042 controller present in Dell Vostro V13 errorneously signals spurious timeouts. Introduce i8042.notimeout parameter for ignoring i8042-signalled timeouts and apply this quirk automatically for Dell Vostro V13, based on DMI match. In addition to that, this machine also needs to be added to nomux blacklist. Signed-off-by: Jiri Kosina Signed-off-by: Dmitry Torokhov diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index ed45e98..185b6bf 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -884,6 +884,7 @@ and is between 256 and 4096 characters. It is defined in the file controller i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX controllers + i8042.notimeout [HW] Ignore timeout condition signalled by conroller i8042.reset [HW] Reset the controller during init and cleanup i8042.unlock [HW] Unlock (ignore) the keylock diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h index 5ae0fc4..bb9f5d3 100644 --- a/drivers/input/serio/i8042-x86ia64io.h +++ b/drivers/input/serio/i8042-x86ia64io.h @@ -424,6 +424,13 @@ static const struct dmi_system_id __initconst i8042_dmi_nomux_table[] = { DMI_MATCH(DMI_PRODUCT_VERSION, "0100"), }, }, + { + /* Dell Vostro V13 */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."), + DMI_MATCH(DMI_PRODUCT_NAME, "Vostro V13"), + }, + }, { } }; @@ -545,6 +552,17 @@ static const struct dmi_system_id __initconst i8042_dmi_laptop_table[] = { }; #endif +static const struct dmi_system_id __initconst i8042_dmi_notimeout_table[] = { + { + /* Dell Vostro V13 */ + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."), + DMI_MATCH(DMI_PRODUCT_NAME, "Vostro V13"), + }, + }, + { } +}; + /* * Some Wistron based laptops need us to explicitly enable the 'Dritek * keyboard extension' to make their extra keys start generating scancodes. @@ -896,6 +914,9 @@ static int __init i8042_platform_init(void) if (dmi_check_system(i8042_dmi_nomux_table)) i8042_nomux = true; + if (dmi_check_system(i8042_dmi_notimeout_table)) + i8042_notimeout = true; + if (dmi_check_system(i8042_dmi_dritek_table)) i8042_dritek = true; #endif /* CONFIG_X86 */ diff --git a/drivers/input/serio/i8042.c b/drivers/input/serio/i8042.c index c04ff00..ac4c936 100644 --- a/drivers/input/serio/i8042.c +++ b/drivers/input/serio/i8042.c @@ -63,6 +63,10 @@ static bool i8042_noloop; module_param_named(noloop, i8042_noloop, bool, 0); MODULE_PARM_DESC(noloop, "Disable the AUX Loopback command while probing for the AUX port"); +static bool i8042_notimeout; +module_param_named(notimeout, i8042_notimeout, bool, 0); +MODULE_PARM_DESC(notimeout, "Ignore timeouts signalled by i8042"); + #ifdef CONFIG_X86 static bool i8042_dritek; module_param_named(dritek, i8042_dritek, bool, 0); @@ -504,7 +508,7 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id) } else { dfl = ((str & I8042_STR_PARITY) ? SERIO_PARITY : 0) | - ((str & I8042_STR_TIMEOUT) ? SERIO_TIMEOUT : 0); + ((str & I8042_STR_TIMEOUT && !i8042_notimeout) ? SERIO_TIMEOUT : 0); port_no = (str & I8042_STR_AUXDATA) ? I8042_AUX_PORT_NO : I8042_KBD_PORT_NO; -- cgit v0.10.2 From 048fc018c81d2acd86db2c3d1e226ea28f646729 Mon Sep 17 00:00:00 2001 From: Jamie Iles Date: Sat, 8 Jan 2011 01:37:42 -0800 Subject: Input: remove aaed2000 keyboard driver The only platform using this driver (mach-aaec2000) is no longer in the kernel so remove the driver. Signed-off-by: Jamie Iles Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig index a378e95..05ab6f4 100644 --- a/drivers/input/keyboard/Kconfig +++ b/drivers/input/keyboard/Kconfig @@ -12,18 +12,6 @@ menuconfig INPUT_KEYBOARD if INPUT_KEYBOARD -config KEYBOARD_AAED2000 - tristate "AAED-2000 keyboard" - depends on MACH_AAED2000 - select INPUT_POLLDEV - default y - help - Say Y here to enable the keyboard on the Agilent AAED-2000 - development board. - - To compile this driver as a module, choose M here: the - module will be called aaed2000_kbd. - config KEYBOARD_ADP5520 tristate "Keypad Support for ADP5520 PMIC" depends on PMIC_ADP5520 diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile index 8449c73..ee14f85 100644 --- a/drivers/input/keyboard/Makefile +++ b/drivers/input/keyboard/Makefile @@ -4,7 +4,6 @@ # Each configuration option enables a list of files. -obj-$(CONFIG_KEYBOARD_AAED2000) += aaed2000_kbd.o obj-$(CONFIG_KEYBOARD_ADP5520) += adp5520-keys.o obj-$(CONFIG_KEYBOARD_ADP5588) += adp5588-keys.o obj-$(CONFIG_KEYBOARD_AMIGA) += amikbd.o diff --git a/drivers/input/keyboard/aaed2000_kbd.c b/drivers/input/keyboard/aaed2000_kbd.c deleted file mode 100644 index 18222a6..0000000 --- a/drivers/input/keyboard/aaed2000_kbd.c +++ /dev/null @@ -1,186 +0,0 @@ -/* - * Keyboard driver for the AAED-2000 dev board - * - * Copyright (c) 2006 Nicolas Bellido Y Ortega - * - * Based on corgikbd.c - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#define KB_ROWS 12 -#define KB_COLS 8 -#define KB_ROWMASK(r) (1 << (r)) -#define SCANCODE(r,c) (((c) * KB_ROWS) + (r)) -#define NR_SCANCODES (KB_COLS * KB_ROWS) - -#define SCAN_INTERVAL (50) /* ms */ -#define KB_ACTIVATE_DELAY (20) /* us */ - -static unsigned char aaedkbd_keycode[NR_SCANCODES] = { - KEY_9, KEY_0, KEY_MINUS, KEY_EQUAL, KEY_BACKSPACE, 0, KEY_SPACE, KEY_KP6, 0, KEY_KPDOT, 0, 0, - KEY_K, KEY_M, KEY_O, KEY_DOT, KEY_SLASH, 0, KEY_F, 0, 0, 0, KEY_LEFTSHIFT, 0, - KEY_I, KEY_P, KEY_LEFTBRACE, KEY_RIGHTBRACE, KEY_BACKSLASH, 0, 0, 0, 0, 0, KEY_RIGHTSHIFT, 0, - KEY_8, KEY_L, KEY_SEMICOLON, KEY_APOSTROPHE, KEY_ENTER, 0, 0, 0, 0, 0, 0, 0, - KEY_J, KEY_H, KEY_B, KEY_KP8, KEY_KP4, 0, KEY_C, KEY_D, KEY_S, KEY_A, 0, KEY_CAPSLOCK, - KEY_Y, KEY_U, KEY_N, KEY_T, 0, 0, KEY_R, KEY_E, KEY_W, KEY_Q, 0, KEY_TAB, - KEY_7, KEY_6, KEY_G, 0, KEY_5, 0, KEY_4, KEY_3, KEY_2, KEY_1, 0, KEY_GRAVE, - 0, 0, KEY_COMMA, 0, KEY_KP2, 0, KEY_V, KEY_LEFTALT, KEY_X, KEY_Z, 0, KEY_LEFTCTRL -}; - -struct aaedkbd { - unsigned char keycode[ARRAY_SIZE(aaedkbd_keycode)]; - struct input_polled_dev *poll_dev; - int kbdscan_state[KB_COLS]; - int kbdscan_count[KB_COLS]; -}; - -#define KBDSCAN_STABLE_COUNT 2 - -static void aaedkbd_report_col(struct aaedkbd *aaedkbd, - unsigned int col, unsigned int rowd) -{ - unsigned int scancode, pressed; - unsigned int row; - - for (row = 0; row < KB_ROWS; row++) { - scancode = SCANCODE(row, col); - pressed = rowd & KB_ROWMASK(row); - - input_report_key(aaedkbd->poll_dev->input, - aaedkbd->keycode[scancode], pressed); - } -} - -/* Scan the hardware keyboard and push any changes up through the input layer */ -static void aaedkbd_poll(struct input_polled_dev *dev) -{ - struct aaedkbd *aaedkbd = dev->private; - unsigned int col, rowd; - - col = 0; - do { - AAEC_GPIO_KSCAN = col + 8; - udelay(KB_ACTIVATE_DELAY); - rowd = AAED_EXT_GPIO & AAED_EGPIO_KBD_SCAN; - - if (rowd != aaedkbd->kbdscan_state[col]) { - aaedkbd->kbdscan_count[col] = 0; - aaedkbd->kbdscan_state[col] = rowd; - } else if (++aaedkbd->kbdscan_count[col] >= KBDSCAN_STABLE_COUNT) { - aaedkbd_report_col(aaedkbd, col, rowd); - col++; - } - } while (col < KB_COLS); - - AAEC_GPIO_KSCAN = 0x07; - input_sync(dev->input); -} - -static int __devinit aaedkbd_probe(struct platform_device *pdev) -{ - struct aaedkbd *aaedkbd; - struct input_polled_dev *poll_dev; - struct input_dev *input_dev; - int i; - int error; - - aaedkbd = kzalloc(sizeof(struct aaedkbd), GFP_KERNEL); - poll_dev = input_allocate_polled_device(); - if (!aaedkbd || !poll_dev) { - error = -ENOMEM; - goto fail; - } - - platform_set_drvdata(pdev, aaedkbd); - - aaedkbd->poll_dev = poll_dev; - memcpy(aaedkbd->keycode, aaedkbd_keycode, sizeof(aaedkbd->keycode)); - - poll_dev->private = aaedkbd; - poll_dev->poll = aaedkbd_poll; - poll_dev->poll_interval = SCAN_INTERVAL; - - input_dev = poll_dev->input; - input_dev->name = "AAED-2000 Keyboard"; - input_dev->phys = "aaedkbd/input0"; - input_dev->id.bustype = BUS_HOST; - input_dev->id.vendor = 0x0001; - input_dev->id.product = 0x0001; - input_dev->id.version = 0x0100; - input_dev->dev.parent = &pdev->dev; - - input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REP); - input_dev->keycode = aaedkbd->keycode; - input_dev->keycodesize = sizeof(unsigned char); - input_dev->keycodemax = ARRAY_SIZE(aaedkbd_keycode); - - for (i = 0; i < ARRAY_SIZE(aaedkbd_keycode); i++) - set_bit(aaedkbd->keycode[i], input_dev->keybit); - clear_bit(0, input_dev->keybit); - - error = input_register_polled_device(aaedkbd->poll_dev); - if (error) - goto fail; - - return 0; - - fail: kfree(aaedkbd); - input_free_polled_device(poll_dev); - return error; -} - -static int __devexit aaedkbd_remove(struct platform_device *pdev) -{ - struct aaedkbd *aaedkbd = platform_get_drvdata(pdev); - - input_unregister_polled_device(aaedkbd->poll_dev); - input_free_polled_device(aaedkbd->poll_dev); - kfree(aaedkbd); - - return 0; -} - -/* work with hotplug and coldplug */ -MODULE_ALIAS("platform:aaed2000-keyboard"); - -static struct platform_driver aaedkbd_driver = { - .probe = aaedkbd_probe, - .remove = __devexit_p(aaedkbd_remove), - .driver = { - .name = "aaed2000-keyboard", - .owner = THIS_MODULE, - }, -}; - -static int __init aaedkbd_init(void) -{ - return platform_driver_register(&aaedkbd_driver); -} - -static void __exit aaedkbd_exit(void) -{ - platform_driver_unregister(&aaedkbd_driver); -} - -module_init(aaedkbd_init); -module_exit(aaedkbd_exit); - -MODULE_AUTHOR("Nicolas Bellido Y Ortega"); -MODULE_DESCRIPTION("AAED-2000 Keyboard Driver"); -MODULE_LICENSE("GPL v2"); -- cgit v0.10.2 From 9d084a3d5dffd076a9a006164ea0dbd9c495f2b0 Mon Sep 17 00:00:00 2001 From: Fabien Marteau Date: Mon, 10 Jan 2011 11:01:13 -0800 Subject: Input: add Austria Microsystem AS5011 joystick driver This is driver for EasyPoint AS5011 2 axis joystick chip. This chip is plugged on an I2C bus. Tested on ARM processor (i.MX27). Signed-off-by: Fabien Marteau Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/joystick/Kconfig b/drivers/input/joystick/Kconfig index 5b59616..56eb471 100644 --- a/drivers/input/joystick/Kconfig +++ b/drivers/input/joystick/Kconfig @@ -255,6 +255,16 @@ config JOYSTICK_AMIGA To compile this driver as a module, choose M here: the module will be called amijoy. +config JOYSTICK_AS5011 + tristate "Austria Microsystem AS5011 joystick" + depends on I2C + help + Say Y here if you have an AS5011 digital joystick connected to your + system. + + To compile this driver as a module, choose M here: the + module will be called as5011. + config JOYSTICK_JOYDUMP tristate "Gameport data dumper" select GAMEPORT diff --git a/drivers/input/joystick/Makefile b/drivers/input/joystick/Makefile index f3a8cbe..92dc0de 100644 --- a/drivers/input/joystick/Makefile +++ b/drivers/input/joystick/Makefile @@ -7,6 +7,7 @@ obj-$(CONFIG_JOYSTICK_A3D) += a3d.o obj-$(CONFIG_JOYSTICK_ADI) += adi.o obj-$(CONFIG_JOYSTICK_AMIGA) += amijoy.o +obj-$(CONFIG_JOYSTICK_AS5011) += as5011.o obj-$(CONFIG_JOYSTICK_ANALOG) += analog.o obj-$(CONFIG_JOYSTICK_COBRA) += cobra.o obj-$(CONFIG_JOYSTICK_DB9) += db9.o diff --git a/drivers/input/joystick/as5011.c b/drivers/input/joystick/as5011.c new file mode 100644 index 0000000..f6732b5 --- /dev/null +++ b/drivers/input/joystick/as5011.c @@ -0,0 +1,367 @@ +/* + * Copyright (c) 2010, 2011 Fabien Marteau + * Sponsored by ARMadeus Systems + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * Driver for Austria Microsystems joysticks AS5011 + * + * TODO: + * - Power on the chip when open() and power down when close() + * - Manage power mode + */ + +#include +#include +#include +#include +#include +#include +#include + +#define DRIVER_DESC "Driver for Austria Microsystems AS5011 joystick" +#define MODULE_DEVICE_ALIAS "as5011" + +MODULE_AUTHOR("Fabien Marteau "); +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL"); + +/* registers */ +#define AS5011_CTRL1 0x76 +#define AS5011_CTRL2 0x75 +#define AS5011_XP 0x43 +#define AS5011_XN 0x44 +#define AS5011_YP 0x53 +#define AS5011_YN 0x54 +#define AS5011_X_REG 0x41 +#define AS5011_Y_REG 0x42 +#define AS5011_X_RES_INT 0x51 +#define AS5011_Y_RES_INT 0x52 + +/* CTRL1 bits */ +#define AS5011_CTRL1_LP_PULSED 0x80 +#define AS5011_CTRL1_LP_ACTIVE 0x40 +#define AS5011_CTRL1_LP_CONTINUE 0x20 +#define AS5011_CTRL1_INT_WUP_EN 0x10 +#define AS5011_CTRL1_INT_ACT_EN 0x08 +#define AS5011_CTRL1_EXT_CLK_EN 0x04 +#define AS5011_CTRL1_SOFT_RST 0x02 +#define AS5011_CTRL1_DATA_VALID 0x01 + +/* CTRL2 bits */ +#define AS5011_CTRL2_EXT_SAMPLE_EN 0x08 +#define AS5011_CTRL2_RC_BIAS_ON 0x04 +#define AS5011_CTRL2_INV_SPINNING 0x02 + +#define AS5011_MAX_AXIS 80 +#define AS5011_MIN_AXIS (-80) +#define AS5011_FUZZ 8 +#define AS5011_FLAT 40 + +struct as5011_device { + struct input_dev *input_dev; + struct i2c_client *i2c_client; + unsigned int button_gpio; + unsigned int button_irq; + unsigned int axis_irq; +}; + +static int as5011_i2c_write(struct i2c_client *client, + uint8_t aregaddr, + uint8_t avalue) +{ + uint8_t data[2] = { aregaddr, avalue }; + struct i2c_msg msg = { + client->addr, I2C_M_IGNORE_NAK, 2, (uint8_t *)data + }; + int error; + + error = i2c_transfer(client->adapter, &msg, 1); + return error < 0 ? error : 0; +} + +static int as5011_i2c_read(struct i2c_client *client, + uint8_t aregaddr, signed char *value) +{ + uint8_t data[2] = { aregaddr }; + struct i2c_msg msg_set[2] = { + { client->addr, I2C_M_REV_DIR_ADDR, 1, (uint8_t *)data }, + { client->addr, I2C_M_RD | I2C_M_NOSTART, 1, (uint8_t *)data } + }; + int error; + + error = i2c_transfer(client->adapter, msg_set, 2); + if (error < 0) + return error; + + *value = data[0] & 0x80 ? -1 * (1 + ~data[0]) : data[0]; + return 0; +} + +static irqreturn_t as5011_button_interrupt(int irq, void *dev_id) +{ + struct as5011_device *as5011 = dev_id; + int val = gpio_get_value_cansleep(as5011->button_gpio); + + input_report_key(as5011->input_dev, BTN_JOYSTICK, !val); + input_sync(as5011->input_dev); + + return IRQ_HANDLED; +} + +static irqreturn_t as5011_axis_interrupt(int irq, void *dev_id) +{ + struct as5011_device *as5011 = dev_id; + int error; + signed char x, y; + + error = as5011_i2c_read(as5011->i2c_client, AS5011_X_RES_INT, &x); + if (error < 0) + goto out; + + error = as5011_i2c_read(as5011->i2c_client, AS5011_Y_RES_INT, &y); + if (error < 0) + goto out; + + input_report_abs(as5011->input_dev, ABS_X, x); + input_report_abs(as5011->input_dev, ABS_Y, y); + input_sync(as5011->input_dev); + +out: + return IRQ_HANDLED; +} + +static int __devinit as5011_configure_chip(struct as5011_device *as5011, + const struct as5011_platform_data *plat_dat) +{ + struct i2c_client *client = as5011->i2c_client; + int error; + signed char value; + + /* chip soft reset */ + error = as5011_i2c_write(client, AS5011_CTRL1, + AS5011_CTRL1_SOFT_RST); + if (error < 0) { + dev_err(&client->dev, "Soft reset failed\n"); + return error; + } + + mdelay(10); + + error = as5011_i2c_write(client, AS5011_CTRL1, + AS5011_CTRL1_LP_PULSED | + AS5011_CTRL1_LP_ACTIVE | + AS5011_CTRL1_INT_ACT_EN); + if (error < 0) { + dev_err(&client->dev, "Power config failed\n"); + return error; + } + + error = as5011_i2c_write(client, AS5011_CTRL2, + AS5011_CTRL2_INV_SPINNING); + if (error < 0) { + dev_err(&client->dev, "Can't invert spinning\n"); + return error; + } + + /* write threshold */ + error = as5011_i2c_write(client, AS5011_XP, plat_dat->xp); + if (error < 0) { + dev_err(&client->dev, "Can't write threshold\n"); + return error; + } + + error = as5011_i2c_write(client, AS5011_XN, plat_dat->xn); + if (error < 0) { + dev_err(&client->dev, "Can't write threshold\n"); + return error; + } + + error = as5011_i2c_write(client, AS5011_YP, plat_dat->yp); + if (error < 0) { + dev_err(&client->dev, "Can't write threshold\n"); + return error; + } + + error = as5011_i2c_write(client, AS5011_YN, plat_dat->yn); + if (error < 0) { + dev_err(&client->dev, "Can't write threshold\n"); + return error; + } + + /* to free irq gpio in chip */ + error = as5011_i2c_read(client, AS5011_X_RES_INT, &value); + if (error < 0) { + dev_err(&client->dev, "Can't read i2c X resolution value\n"); + return error; + } + + return 0; +} + +static int __devinit as5011_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + const struct as5011_platform_data *plat_data; + struct as5011_device *as5011; + struct input_dev *input_dev; + int irq; + int error; + + plat_data = client->dev.platform_data; + if (!plat_data) + return -EINVAL; + + if (!plat_data->axis_irq) { + dev_err(&client->dev, "No axis IRQ?\n"); + return -EINVAL; + } + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_PROTOCOL_MANGLING)) { + dev_err(&client->dev, + "need i2c bus that supports protocol mangling\n"); + return -ENODEV; + } + + as5011 = kmalloc(sizeof(struct as5011_device), GFP_KERNEL); + input_dev = input_allocate_device(); + if (!as5011 || !input_dev) { + dev_err(&client->dev, + "Can't allocate memory for device structure\n"); + error = -ENOMEM; + goto err_free_mem; + } + + as5011->i2c_client = client; + as5011->input_dev = input_dev; + as5011->button_gpio = plat_data->button_gpio; + as5011->axis_irq = plat_data->axis_irq; + + input_dev->name = "Austria Microsystem as5011 joystick"; + input_dev->id.bustype = BUS_I2C; + input_dev->dev.parent = &client->dev; + + __set_bit(EV_KEY, input_dev->evbit); + __set_bit(EV_ABS, input_dev->evbit); + __set_bit(BTN_JOYSTICK, input_dev->keybit); + + input_set_abs_params(input_dev, ABS_X, + AS5011_MIN_AXIS, AS5011_MAX_AXIS, AS5011_FUZZ, AS5011_FLAT); + input_set_abs_params(as5011->input_dev, ABS_Y, + AS5011_MIN_AXIS, AS5011_MAX_AXIS, AS5011_FUZZ, AS5011_FLAT); + + error = gpio_request(as5011->button_gpio, "AS5011 button"); + if (error < 0) { + dev_err(&client->dev, "Failed to request button gpio\n"); + goto err_free_mem; + } + + irq = gpio_to_irq(as5011->button_gpio); + if (irq < 0) { + dev_err(&client->dev, + "Failed to get irq number for button gpio\n"); + goto err_free_button_gpio; + } + + as5011->button_irq = irq; + + error = request_threaded_irq(as5011->button_irq, + NULL, as5011_button_interrupt, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "as5011_button", as5011); + if (error < 0) { + dev_err(&client->dev, + "Can't allocate button irq %d\n", as5011->button_irq); + goto err_free_button_gpio; + } + + error = as5011_configure_chip(as5011, plat_data); + if (error) + goto err_free_button_irq; + + error = request_threaded_irq(as5011->axis_irq, NULL, + as5011_axis_interrupt, + plat_data->axis_irqflags, + "as5011_joystick", as5011); + if (error) { + dev_err(&client->dev, + "Can't allocate axis irq %d\n", plat_data->axis_irq); + goto err_free_button_irq; + } + + error = input_register_device(as5011->input_dev); + if (error) { + dev_err(&client->dev, "Failed to register input device\n"); + goto err_free_axis_irq; + } + + i2c_set_clientdata(client, as5011); + + return 0; + +err_free_axis_irq: + free_irq(as5011->axis_irq, as5011); +err_free_button_irq: + free_irq(as5011->button_irq, as5011); +err_free_button_gpio: + gpio_free(as5011->button_gpio); +err_free_mem: + input_free_device(input_dev); + kfree(as5011); + + return error; +} + +static int __devexit as5011_remove(struct i2c_client *client) +{ + struct as5011_device *as5011 = i2c_get_clientdata(client); + + free_irq(as5011->axis_irq, as5011); + free_irq(as5011->button_irq, as5011); + gpio_free(as5011->button_gpio); + + input_unregister_device(as5011->input_dev); + kfree(as5011); + + return 0; +} + +static const struct i2c_device_id as5011_id[] = { + { MODULE_DEVICE_ALIAS, 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, as5011_id); + +static struct i2c_driver as5011_driver = { + .driver = { + .name = "as5011", + }, + .probe = as5011_probe, + .remove = __devexit_p(as5011_remove), + .id_table = as5011_id, +}; + +static int __init as5011_init(void) +{ + return i2c_add_driver(&as5011_driver); +} +module_init(as5011_init); + +static void __exit as5011_exit(void) +{ + i2c_del_driver(&as5011_driver); +} +module_exit(as5011_exit); diff --git a/include/linux/input/as5011.h b/include/linux/input/as5011.h new file mode 100644 index 0000000..1affd0d --- /dev/null +++ b/include/linux/input/as5011.h @@ -0,0 +1,20 @@ +#ifndef _AS5011_H +#define _AS5011_H + +/* + * Copyright (c) 2010, 2011 Fabien Marteau + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ + +struct as5011_platform_data { + unsigned int button_gpio; + unsigned int axis_irq; /* irq number */ + unsigned long axis_irqflags; + char xp, xn; /* threshold for x axis */ + char yp, yn; /* threshold for y axis */ +}; + +#endif /* _AS5011_H */ -- cgit v0.10.2 From 5fca6cac9feed75efc0b2c454305a5f538d887f5 Mon Sep 17 00:00:00 2001 From: Ping Cheng Date: Tue, 11 Jan 2011 01:06:58 -0800 Subject: Input: wacom_w8001 - add single-touch support Emulate single-touch compatible events for the 2-finger panels so that they can be used with single-touch legacy clients. Assign device ids as Wacom USB vendor ID and product ID. Name the device to reflect its specific features. Scale touch coordinates to pen maximum if pen supported. Signed-off-by: Ping Cheng Signed-off-by: Dmitry Torokhov diff --git a/drivers/input/touchscreen/wacom_w8001.c b/drivers/input/touchscreen/wacom_w8001.c index 8ed53ad..5cb8449 100644 --- a/drivers/input/touchscreen/wacom_w8001.c +++ b/drivers/input/touchscreen/wacom_w8001.c @@ -3,6 +3,7 @@ * * Copyright (c) 2008 Jaya Kumar * Copyright (c) 2010 Red Hat, Inc. + * Copyright (c) 2010 - 2011 Ping Cheng, Wacom. * * This file is subject to the terms and conditions of the GNU General Public * License. See the file COPYING in the main directory of this archive for @@ -64,11 +65,11 @@ struct w8001_coord { /* touch query reply packet */ struct w8001_touch_query { + u16 x; + u16 y; u8 panel_res; u8 capacity_res; u8 sensor_id; - u16 x; - u16 y; }; /* @@ -87,9 +88,14 @@ struct w8001 { char phys[32]; int type; unsigned int pktlen; + u16 max_touch_x; + u16 max_touch_y; + u16 max_pen_x; + u16 max_pen_y; + char name[64]; }; -static void parse_data(u8 *data, struct w8001_coord *coord) +static void parse_pen_data(u8 *data, struct w8001_coord *coord) { memset(coord, 0, sizeof(*coord)); @@ -113,11 +119,30 @@ static void parse_data(u8 *data, struct w8001_coord *coord) coord->tilt_y = data[8] & 0x7F; } -static void parse_touch(struct w8001 *w8001) +static void parse_single_touch(u8 *data, struct w8001_coord *coord) +{ + coord->x = (data[1] << 7) | data[2]; + coord->y = (data[3] << 7) | data[4]; + coord->tsw = data[0] & 0x01; +} + +static void scale_touch_coordinates(struct w8001 *w8001, + unsigned int *x, unsigned int *y) +{ + if (w8001->max_pen_x && w8001->max_touch_x) + *x = *x * w8001->max_pen_x / w8001->max_touch_x; + + if (w8001->max_pen_y && w8001->max_touch_y) + *y = *y * w8001->max_pen_y / w8001->max_touch_y; +} + +static void parse_multi_touch(struct w8001 *w8001) { struct input_dev *dev = w8001->dev; unsigned char *data = w8001->data; + unsigned int x, y; int i; + int count = 0; for (i = 0; i < 2; i++) { bool touch = data[0] & (1 << i); @@ -125,15 +150,29 @@ static void parse_touch(struct w8001 *w8001) input_mt_slot(dev, i); input_mt_report_slot_state(dev, MT_TOOL_FINGER, touch); if (touch) { - int x = (data[6 * i + 1] << 7) | (data[6 * i + 2]); - int y = (data[6 * i + 3] << 7) | (data[6 * i + 4]); + x = (data[6 * i + 1] << 7) | data[6 * i + 2]; + y = (data[6 * i + 3] << 7) | data[6 * i + 4]; /* data[5,6] and [11,12] is finger capacity */ + /* scale to pen maximum */ + scale_touch_coordinates(w8001, &x, &y); + input_report_abs(dev, ABS_MT_POSITION_X, x); input_report_abs(dev, ABS_MT_POSITION_Y, y); + count++; } } + /* emulate single touch events when stylus is out of proximity. + * This is to make single touch backward support consistent + * across all Wacom single touch devices. + */ + if (w8001->type != BTN_TOOL_PEN && + w8001->type != BTN_TOOL_RUBBER) { + w8001->type = count == 1 ? BTN_TOOL_FINGER : KEY_RESERVED; + input_mt_report_pointer_emulation(dev, true); + } + input_sync(dev); } @@ -152,6 +191,15 @@ static void parse_touchquery(u8 *data, struct w8001_touch_query *query) query->y = data[5] << 9; query->y |= data[6] << 2; query->y |= (data[2] >> 3) & 0x3; + + /* Early days' single-finger touch models need the following defaults */ + if (!query->x && !query->y) { + query->x = 1024; + query->y = 1024; + if (query->panel_res) + query->x = query->y = (1 << query->panel_res); + query->panel_res = 10; + } } static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord) @@ -161,16 +209,15 @@ static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord) /* * We have 1 bit for proximity (rdy) and 3 bits for tip, side, * side2/eraser. If rdy && f2 are set, this can be either pen + side2, - * or eraser. assume + * or eraser. Assume: * - if dev is already in proximity and f2 is toggled → pen + side2 * - if dev comes into proximity with f2 set → eraser * If f2 disappears after assuming eraser, fake proximity out for * eraser and in for pen. */ - if (!w8001->type) { - w8001->type = coord->f2 ? BTN_TOOL_RUBBER : BTN_TOOL_PEN; - } else if (w8001->type == BTN_TOOL_RUBBER) { + switch (w8001->type) { + case BTN_TOOL_RUBBER: if (!coord->f2) { input_report_abs(dev, ABS_PRESSURE, 0); input_report_key(dev, BTN_TOUCH, 0); @@ -180,8 +227,21 @@ static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord) input_sync(dev); w8001->type = BTN_TOOL_PEN; } - } else { + break; + + case BTN_TOOL_FINGER: + input_report_key(dev, BTN_TOUCH, 0); + input_report_key(dev, BTN_TOOL_FINGER, 0); + input_sync(dev); + /* fall through */ + + case KEY_RESERVED: + w8001->type = coord->f2 ? BTN_TOOL_RUBBER : BTN_TOOL_PEN; + break; + + default: input_report_key(dev, BTN_STYLUS2, coord->f2); + break; } input_report_abs(dev, ABS_X, coord->x); @@ -193,7 +253,26 @@ static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord) input_sync(dev); if (!coord->rdy) - w8001->type = 0; + w8001->type = KEY_RESERVED; +} + +static void report_single_touch(struct w8001 *w8001, struct w8001_coord *coord) +{ + struct input_dev *dev = w8001->dev; + unsigned int x = coord->x; + unsigned int y = coord->y; + + /* scale to pen maximum */ + scale_touch_coordinates(w8001, &x, &y); + + input_report_abs(dev, ABS_X, x); + input_report_abs(dev, ABS_Y, y); + input_report_key(dev, BTN_TOUCH, coord->tsw); + input_report_key(dev, BTN_TOOL_FINGER, coord->tsw); + + input_sync(dev); + + w8001->type = coord->tsw ? BTN_TOOL_FINGER : KEY_RESERVED; } static irqreturn_t w8001_interrupt(struct serio *serio, @@ -214,9 +293,18 @@ static irqreturn_t w8001_interrupt(struct serio *serio, case W8001_PKTLEN_TOUCH93 - 1: case W8001_PKTLEN_TOUCH9A - 1: - /* ignore one-finger touch packet. */ - if (w8001->pktlen == w8001->idx) + tmp = w8001->data[0] & W8001_TOUCH_BYTE; + if (tmp != W8001_TOUCH_BYTE) + break; + + if (w8001->pktlen == w8001->idx) { w8001->idx = 0; + if (w8001->type != BTN_TOOL_PEN && + w8001->type != BTN_TOOL_RUBBER) { + parse_single_touch(w8001->data, &coord); + report_single_touch(w8001, &coord); + } + } break; /* Pen coordinates packet */ @@ -225,18 +313,18 @@ static irqreturn_t w8001_interrupt(struct serio *serio, if (unlikely(tmp == W8001_TAB_BYTE)) break; - tmp = (w8001->data[0] & W8001_TOUCH_BYTE); + tmp = w8001->data[0] & W8001_TOUCH_BYTE; if (tmp == W8001_TOUCH_BYTE) break; w8001->idx = 0; - parse_data(w8001->data, &coord); + parse_pen_data(w8001->data, &coord); report_pen_events(w8001, &coord); break; /* control packet */ case W8001_PKTLEN_TPCCTL - 1: - tmp = (w8001->data[0] & W8001_TOUCH_MASK); + tmp = w8001->data[0] & W8001_TOUCH_MASK; if (tmp == W8001_TOUCH_BYTE) break; @@ -249,7 +337,7 @@ static irqreturn_t w8001_interrupt(struct serio *serio, /* 2 finger touch packet */ case W8001_PKTLEN_TOUCH2FG - 1: w8001->idx = 0; - parse_touch(w8001); + parse_multi_touch(w8001); break; } @@ -279,6 +367,7 @@ static int w8001_setup(struct w8001 *w8001) { struct input_dev *dev = w8001->dev; struct w8001_coord coord; + struct w8001_touch_query touch; int error; error = w8001_command(w8001, W8001_CMD_STOP, false); @@ -287,14 +376,21 @@ static int w8001_setup(struct w8001 *w8001) msleep(250); /* wait 250ms before querying the device */ + dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS); + strlcat(w8001->name, "Wacom Serial", sizeof(w8001->name)); + /* penabled? */ error = w8001_command(w8001, W8001_CMD_QUERY, true); if (!error) { + __set_bit(BTN_TOUCH, dev->keybit); __set_bit(BTN_TOOL_PEN, dev->keybit); __set_bit(BTN_TOOL_RUBBER, dev->keybit); __set_bit(BTN_STYLUS, dev->keybit); __set_bit(BTN_STYLUS2, dev->keybit); - parse_data(w8001->response, &coord); + + parse_pen_data(w8001->response, &coord); + w8001->max_pen_x = coord.x; + w8001->max_pen_y = coord.y; input_set_abs_params(dev, ABS_X, 0, coord.x, 0, 0); input_set_abs_params(dev, ABS_Y, 0, coord.y, 0, 0); @@ -303,6 +399,8 @@ static int w8001_setup(struct w8001 *w8001) input_set_abs_params(dev, ABS_TILT_X, 0, coord.tilt_x, 0, 0); input_set_abs_params(dev, ABS_TILT_Y, 0, coord.tilt_y, 0, 0); } + w8001->id = 0x90; + strlcat(w8001->name, " Penabled", sizeof(w8001->name)); } /* Touch enabled? */ @@ -313,24 +411,38 @@ static int w8001_setup(struct w8001 *w8001) * second byte is empty, which indicates touch is not supported. */ if (!error && w8001->response[1]) { - struct w8001_touch_query touch; + __set_bit(BTN_TOUCH, dev->keybit); + __set_bit(BTN_TOOL_FINGER, dev->keybit); parse_touchquery(w8001->response, &touch); + w8001->max_touch_x = touch.x; + w8001->max_touch_y = touch.y; + + /* scale to pen maximum */ + if (w8001->max_pen_x && w8001->max_pen_y) { + touch.x = w8001->max_pen_x; + touch.y = w8001->max_pen_y; + } input_set_abs_params(dev, ABS_X, 0, touch.x, 0, 0); input_set_abs_params(dev, ABS_Y, 0, touch.y, 0, 0); - __set_bit(BTN_TOOL_FINGER, dev->keybit); switch (touch.sensor_id) { case 0: case 2: w8001->pktlen = W8001_PKTLEN_TOUCH93; + w8001->id = 0x93; + strlcat(w8001->name, " 1FG", sizeof(w8001->name)); break; + case 1: case 3: case 4: w8001->pktlen = W8001_PKTLEN_TOUCH9A; + strlcat(w8001->name, " 1FG", sizeof(w8001->name)); + w8001->id = 0x9a; break; + case 5: w8001->pktlen = W8001_PKTLEN_TOUCH2FG; @@ -341,10 +453,18 @@ static int w8001_setup(struct w8001 *w8001) 0, touch.y, 0, 0); input_set_abs_params(dev, ABS_MT_TOOL_TYPE, 0, MT_TOOL_MAX, 0, 0); + + strlcat(w8001->name, " 2FG", sizeof(w8001->name)); + if (w8001->max_pen_x && w8001->max_pen_y) + w8001->id = 0xE3; + else + w8001->id = 0xE2; break; } } + strlcat(w8001->name, " Touchscreen", sizeof(w8001->name)); + return w8001_command(w8001, W8001_CMD_START, false); } @@ -384,22 +504,10 @@ static int w8001_connect(struct serio *serio, struct serio_driver *drv) } w8001->serio = serio; - w8001->id = serio->id.id; w8001->dev = input_dev; init_completion(&w8001->cmd_done); snprintf(w8001->phys, sizeof(w8001->phys), "%s/input0", serio->phys); - input_dev->name = "Wacom W8001 Penabled Serial TouchScreen"; - input_dev->phys = w8001->phys; - input_dev->id.bustype = BUS_RS232; - input_dev->id.vendor = SERIO_W8001; - input_dev->id.product = w8001->id; - input_dev->id.version = 0x0100; - input_dev->dev.parent = &serio->dev; - - input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS); - __set_bit(BTN_TOUCH, input_dev->keybit); - serio_set_drvdata(serio, w8001); err = serio_open(serio, drv); if (err) @@ -409,6 +517,14 @@ static int w8001_connect(struct serio *serio, struct serio_driver *drv) if (err) goto fail3; + input_dev->name = w8001->name; + input_dev->phys = w8001->phys; + input_dev->id.product = w8001->id; + input_dev->id.bustype = BUS_RS232; + input_dev->id.vendor = 0x056a; + input_dev->id.version = 0x0100; + input_dev->dev.parent = &serio->dev; + err = input_register_device(w8001->dev); if (err) goto fail3; -- cgit v0.10.2 From e1336bff92c6e0f4e6212af13f11d20c29a900a2 Mon Sep 17 00:00:00 2001 From: Alexander Stein Date: Tue, 11 Jan 2011 01:07:09 -0800 Subject: Input: fix force feedback capability query example 'features' is a bit array, not byte array Signed-off-by: Alexander Stein Acked-by: Anssi Hannula Signed-off-by: Dmitry Torokhov diff --git a/Documentation/input/ff.txt b/Documentation/input/ff.txt index ded4d5f..b3867bf 100644 --- a/Documentation/input/ff.txt +++ b/Documentation/input/ff.txt @@ -49,7 +49,9 @@ This information is subject to change. #include #include -unsigned long features[1 + FF_MAX/sizeof(unsigned long)]; +#define BITS_TO_LONGS(x) \ + (((x) + 8 * sizeof (unsigned long) - 1) / (8 * sizeof (unsigned long))) +unsigned long features[BITS_TO_LONGS(FF_CNT)]; int ioctl(int file_descriptor, int request, unsigned long *features); "request" must be EVIOCGBIT(EV_FF, size of features array in bytes ) -- cgit v0.10.2 From 50a88cb7eddb971077ae7dff76b116747c12c371 Mon Sep 17 00:00:00 2001 From: Jekyll Lai Date: Tue, 11 Jan 2011 21:53:55 -0800 Subject: Input: add SW_ROTATE_LOCK switch type This switch is used to signal that user want to disable screen transitions from portrait to landscape mode and back. Signed-off-by: Jekyll Lai Signed-off-by: Alan Cox Signed-off-by: Dmitry Torokhov diff --git a/include/linux/input.h b/include/linux/input.h index 6c407e5..4bdacad 100644 --- a/include/linux/input.h +++ b/include/linux/input.h @@ -775,6 +775,7 @@ struct input_keymap_entry { #define SW_CAMERA_LENS_COVER 0x09 /* set = lens covered */ #define SW_KEYPAD_SLIDE 0x0a /* set = keypad slide out */ #define SW_FRONT_PROXIMITY 0x0b /* set = front proximity sensor active */ +#define SW_ROTATE_LOCK 0x0c /* set = rotate locked/disabled */ #define SW_MAX 0x0f #define SW_CNT (SW_MAX+1) -- cgit v0.10.2