From 00db8189d984d6c51226dafbbe4a667ce9b7d5da Mon Sep 17 00:00:00 2001 From: Andy Fleming Date: Sat, 30 Jul 2005 19:31:23 -0400 Subject: This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details. Signed-off-by: Andy Fleming Signed-off-by: Jeff Garzik diff --git a/Documentation/networking/phy.txt b/Documentation/networking/phy.txt new file mode 100644 index 0000000..29ccae4 --- /dev/null +++ b/Documentation/networking/phy.txt @@ -0,0 +1,288 @@ + +------- +PHY Abstraction Layer +(Updated 2005-07-21) + +Purpose + + Most network devices consist of set of registers which provide an interface + to a MAC layer, which communicates with the physical connection through a + PHY. The PHY concerns itself with negotiating link parameters with the link + partner on the other side of the network connection (typically, an ethernet + cable), and provides a register interface to allow drivers to determine what + settings were chosen, and to configure what settings are allowed. + + While these devices are distinct from the network devices, and conform to a + standard layout for the registers, it has been common practice to integrate + the PHY management code with the network driver. This has resulted in large + amounts of redundant code. Also, on embedded systems with multiple (and + sometimes quite different) ethernet controllers connected to the same + management bus, it is difficult to ensure safe use of the bus. + + Since the PHYs are devices, and the management busses through which they are + accessed are, in fact, busses, the PHY Abstraction Layer treats them as such. + In doing so, it has these goals: + + 1) Increase code-reuse + 2) Increase overall code-maintainability + 3) Speed development time for new network drivers, and for new systems + + Basically, this layer is meant to provide an interface to PHY devices which + allows network driver writers to write as little code as possible, while + still providing a full feature set. + +The MDIO bus + + Most network devices are connected to a PHY by means of a management bus. + Different devices use different busses (though some share common interfaces). + In order to take advantage of the PAL, each bus interface needs to be + registered as a distinct device. + + 1) read and write functions must be implemented. Their prototypes are: + + int write(struct mii_bus *bus, int mii_id, int regnum, u16 value); + int read(struct mii_bus *bus, int mii_id, int regnum); + + mii_id is the address on the bus for the PHY, and regnum is the register + number. These functions are guaranteed not to be called from interrupt + time, so it is safe for them to block, waiting for an interrupt to signal + the operation is complete + + 2) A reset function is necessary. This is used to return the bus to an + initialized state. + + 3) A probe function is needed. This function should set up anything the bus + driver needs, setup the mii_bus structure, and register with the PAL using + mdiobus_register. Similarly, there's a remove function to undo all of + that (use mdiobus_unregister). + + 4) Like any driver, the device_driver structure must be configured, and init + exit functions are used to register the driver. + + 5) The bus must also be declared somewhere as a device, and registered. + + As an example for how one driver implemented an mdio bus driver, see + drivers/net/gianfar_mii.c and arch/ppc/syslib/mpc85xx_devices.c + +Connecting to a PHY + + Sometime during startup, the network driver needs to establish a connection + between the PHY device, and the network device. At this time, the PHY's bus + and drivers need to all have been loaded, so it is ready for the connection. + At this point, there are several ways to connect to the PHY: + + 1) The PAL handles everything, and only calls the network driver when + the link state changes, so it can react. + + 2) The PAL handles everything except interrupts (usually because the + controller has the interrupt registers). + + 3) The PAL handles everything, but checks in with the driver every second, + allowing the network driver to react first to any changes before the PAL + does. + + 4) The PAL serves only as a library of functions, with the network device + manually calling functions to update status, and configure the PHY + + +Letting the PHY Abstraction Layer do Everything + + If you choose option 1 (The hope is that every driver can, but to still be + useful to drivers that can't), connecting to the PHY is simple: + + First, you need a function to react to changes in the link state. This + function follows this protocol: + + static void adjust_link(struct net_device *dev); + + Next, you need to know the device name of the PHY connected to this device. + The name will look something like, "phy0:0", where the first number is the + bus id, and the second is the PHY's address on that bus. + + Now, to connect, just call this function: + + phydev = phy_connect(dev, phy_name, &adjust_link, flags); + + phydev is a pointer to the phy_device structure which represents the PHY. If + phy_connect is successful, it will return the pointer. dev, here, is the + pointer to your net_device. Once done, this function will have started the + PHY's software state machine, and registered for the PHY's interrupt, if it + has one. The phydev structure will be populated with information about the + current state, though the PHY will not yet be truly operational at this + point. + + flags is a u32 which can optionally contain phy-specific flags. + This is useful if the system has put hardware restrictions on + the PHY/controller, of which the PHY needs to be aware. + + Now just make sure that phydev->supported and phydev->advertising have any + values pruned from them which don't make sense for your controller (a 10/100 + controller may be connected to a gigabit capable PHY, so you would need to + mask off SUPPORTED_1000baseT*). See include/linux/ethtool.h for definitions + for these bitfields. Note that you should not SET any bits, or the PHY may + get put into an unsupported state. + + Lastly, once the controller is ready to handle network traffic, you call + phy_start(phydev). This tells the PAL that you are ready, and configures the + PHY to connect to the network. If you want to handle your own interrupts, + just set phydev->irq to PHY_IGNORE_INTERRUPT before you call phy_start. + Similarly, if you don't want to use interrupts, set phydev->irq to PHY_POLL. + + When you want to disconnect from the network (even if just briefly), you call + phy_stop(phydev). + +Keeping Close Tabs on the PAL + + It is possible that the PAL's built-in state machine needs a little help to + keep your network device and the PHY properly in sync. If so, you can + register a helper function when connecting to the PHY, which will be called + every second before the state machine reacts to any changes. To do this, you + need to manually call phy_attach() and phy_prepare_link(), and then call + phy_start_machine() with the second argument set to point to your special + handler. + + Currently there are no examples of how to use this functionality, and testing + on it has been limited because the author does not have any drivers which use + it (they all use option 1). So Caveat Emptor. + +Doing it all yourself + + There's a remote chance that the PAL's built-in state machine cannot track + the complex interactions between the PHY and your network device. If this is + so, you can simply call phy_attach(), and not call phy_start_machine or + phy_prepare_link(). This will mean that phydev->state is entirely yours to + handle (phy_start and phy_stop toggle between some of the states, so you + might need to avoid them). + + An effort has been made to make sure that useful functionality can be + accessed without the state-machine running, and most of these functions are + descended from functions which did not interact with a complex state-machine. + However, again, no effort has been made so far to test running without the + state machine, so tryer beware. + + Here is a brief rundown of the functions: + + int phy_read(struct phy_device *phydev, u16 regnum); + int phy_write(struct phy_device *phydev, u16 regnum, u16 val); + + Simple read/write primitives. They invoke the bus's read/write function + pointers. + + void phy_print_status(struct phy_device *phydev); + + A convenience function to print out the PHY status neatly. + + int phy_clear_interrupt(struct phy_device *phydev); + int phy_config_interrupt(struct phy_device *phydev, u32 interrupts); + + Clear the PHY's interrupt, and configure which ones are allowed, + respectively. Currently only supports all on, or all off. + + int phy_enable_interrupts(struct phy_device *phydev); + int phy_disable_interrupts(struct phy_device *phydev); + + Functions which enable/disable PHY interrupts, clearing them + before and after, respectively. + + int phy_start_interrupts(struct phy_device *phydev); + int phy_stop_interrupts(struct phy_device *phydev); + + Requests the IRQ for the PHY interrupts, then enables them for + start, or disables then frees them for stop. + + struct phy_device * phy_attach(struct net_device *dev, const char *phy_id, + u32 flags); + + Attaches a network device to a particular PHY, binding the PHY to a generic + driver if none was found during bus initialization. Passes in + any phy-specific flags as needed. + + int phy_start_aneg(struct phy_device *phydev); + + Using variables inside the phydev structure, either configures advertising + and resets autonegotiation, or disables autonegotiation, and configures + forced settings. + + static inline int phy_read_status(struct phy_device *phydev); + + Fills the phydev structure with up-to-date information about the current + settings in the PHY. + + void phy_sanitize_settings(struct phy_device *phydev) + + Resolves differences between currently desired settings, and + supported settings for the given PHY device. Does not make + the changes in the hardware, though. + + int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd); + int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd); + + Ethtool convenience functions. + + int phy_mii_ioctl(struct phy_device *phydev, + struct mii_ioctl_data *mii_data, int cmd); + + The MII ioctl. Note that this function will completely screw up the state + machine if you write registers like BMCR, BMSR, ADVERTISE, etc. Best to + use this only to write registers which are not standard, and don't set off + a renegotiation. + + +PHY Device Drivers + + With the PHY Abstraction Layer, adding support for new PHYs is + quite easy. In some cases, no work is required at all! However, + many PHYs require a little hand-holding to get up-and-running. + +Generic PHY driver + + If the desired PHY doesn't have any errata, quirks, or special + features you want to support, then it may be best to not add + support, and let the PHY Abstraction Layer's Generic PHY Driver + do all of the work. + +Writing a PHY driver + + If you do need to write a PHY driver, the first thing to do is + make sure it can be matched with an appropriate PHY device. + This is done during bus initialization by reading the device's + UID (stored in registers 2 and 3), then comparing it to each + driver's phy_id field by ANDing it with each driver's + phy_id_mask field. Also, it needs a name. Here's an example: + + static struct phy_driver dm9161_driver = { + .phy_id = 0x0181b880, + .name = "Davicom DM9161E", + .phy_id_mask = 0x0ffffff0, + ... + } + + Next, you need to specify what features (speed, duplex, autoneg, + etc) your PHY device and driver support. Most PHYs support + PHY_BASIC_FEATURES, but you can look in include/mii.h for other + features. + + Each driver consists of a number of function pointers: + + config_init: configures PHY into a sane state after a reset. + For instance, a Davicom PHY requires descrambling disabled. + probe: Does any setup needed by the driver + suspend/resume: power management + config_aneg: Changes the speed/duplex/negotiation settings + read_status: Reads the current speed/duplex/negotiation settings + ack_interrupt: Clear a pending interrupt + config_intr: Enable or disable interrupts + remove: Does any driver take-down + + Of these, only config_aneg and read_status are required to be + assigned by the driver code. The rest are optional. Also, it is + preferred to use the generic phy driver's versions of these two + functions if at all possible: genphy_read_status and + genphy_config_aneg. If this is not possible, it is likely that + you only need to perform some actions before and after invoking + these functions, and so your functions will wrap the generic + ones. + + Feel free to look at the Marvell, Cicada, and Davicom drivers in + drivers/net/phy/ for examples (the lxt and qsemi drivers have + not been tested as of this writing) diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 8a835eb..1e50b8e 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -131,6 +131,8 @@ config NET_SB1000 source "drivers/net/arcnet/Kconfig" +source "drivers/net/phy/Kconfig" + # # Ethernet # diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 63c6d1e..a369ae2 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -65,6 +65,7 @@ obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o # obj-$(CONFIG_MII) += mii.o +obj-$(CONFIG_PHYLIB) += phy/ obj-$(CONFIG_SUNDANCE) += sundance.o obj-$(CONFIG_HAMACHI) += hamachi.o diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig new file mode 100644 index 0000000..8b5db23 --- /dev/null +++ b/drivers/net/phy/Kconfig @@ -0,0 +1,57 @@ +# +# PHY Layer Configuration +# + +menu "PHY device support" + +config PHYLIB + bool "PHY Device support and infrastructure" + depends on NET_ETHERNET + help + Ethernet controllers are usually attached to PHY + devices. This option provides infrastructure for + managing PHY devices. + +config PHYCONTROL + bool "Support for automatically handling PHY state changes" + depends on PHYLIB + help + Adds code to perform all the work for keeping PHY link + state (speed/duplex/etc) up-to-date. Also handles + interrupts. + +comment "MII PHY device drivers" + depends on PHYLIB + +config MARVELL_PHY + bool "Drivers for Marvell PHYs" + depends on PHYLIB + ---help--- + Currently has a driver for the 88E1011S + +config DAVICOM_PHY + bool "Drivers for Davicom PHYs" + depends on PHYLIB + ---help--- + Currently supports dm9161e and dm9131 + +config QSEMI_PHY + bool "Drivers for Quality Semiconductor PHYs" + depends on PHYLIB + ---help--- + Currently supports the qs6612 + +config LXT_PHY + bool "Drivers for the Intel LXT PHYs" + depends on PHYLIB + ---help--- + Currently supports the lxt970, lxt971 + +config CICADA_PHY + bool "Drivers for the Cicada PHYs" + depends on PHYLIB + ---help--- + Currently supports the cis8204 + +endmenu + diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile new file mode 100644 index 0000000..1af05de --- /dev/null +++ b/drivers/net/phy/Makefile @@ -0,0 +1,9 @@ +# Makefile for Linux PHY drivers + +obj-$(CONFIG_PHYLIB) += phy.o phy_device.o mdio_bus.o + +obj-$(CONFIG_MARVELL_PHY) += marvell.o +obj-$(CONFIG_DAVICOM_PHY) += davicom.o +obj-$(CONFIG_CICADA_PHY) += cicada.o +obj-$(CONFIG_LXT_PHY) += lxt.o +obj-$(CONFIG_QSEMI_PHY) += qsemi.o diff --git a/drivers/net/phy/cicada.c b/drivers/net/phy/cicada.c new file mode 100644 index 0000000..c47fb2e --- /dev/null +++ b/drivers/net/phy/cicada.c @@ -0,0 +1,134 @@ +/* + * drivers/net/phy/cicada.c + * + * Driver for Cicada PHYs + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +/* Cicada Extended Control Register 1 */ +#define MII_CIS8201_EXT_CON1 0x17 +#define MII_CIS8201_EXTCON1_INIT 0x0000 + +/* Cicada Interrupt Mask Register */ +#define MII_CIS8201_IMASK 0x19 +#define MII_CIS8201_IMASK_IEN 0x8000 +#define MII_CIS8201_IMASK_SPEED 0x4000 +#define MII_CIS8201_IMASK_LINK 0x2000 +#define MII_CIS8201_IMASK_DUPLEX 0x1000 +#define MII_CIS8201_IMASK_MASK 0xf000 + +/* Cicada Interrupt Status Register */ +#define MII_CIS8201_ISTAT 0x1a +#define MII_CIS8201_ISTAT_STATUS 0x8000 +#define MII_CIS8201_ISTAT_SPEED 0x4000 +#define MII_CIS8201_ISTAT_LINK 0x2000 +#define MII_CIS8201_ISTAT_DUPLEX 0x1000 + +/* Cicada Auxiliary Control/Status Register */ +#define MII_CIS8201_AUX_CONSTAT 0x1c +#define MII_CIS8201_AUXCONSTAT_INIT 0x0004 +#define MII_CIS8201_AUXCONSTAT_DUPLEX 0x0020 +#define MII_CIS8201_AUXCONSTAT_SPEED 0x0018 +#define MII_CIS8201_AUXCONSTAT_GBIT 0x0010 +#define MII_CIS8201_AUXCONSTAT_100 0x0008 + +MODULE_DESCRIPTION("Cicadia PHY driver"); +MODULE_AUTHOR("Andy Fleming"); +MODULE_LICENSE("GPL"); + +static int cis820x_config_init(struct phy_device *phydev) +{ + int err; + + err = phy_write(phydev, MII_CIS8201_AUX_CONSTAT, + MII_CIS8201_AUXCONSTAT_INIT); + + if (err < 0) + return err; + + err = phy_write(phydev, MII_CIS8201_EXT_CON1, + MII_CIS8201_EXTCON1_INIT); + + return err; +} + +static int cis820x_ack_interrupt(struct phy_device *phydev) +{ + int err = phy_read(phydev, MII_CIS8201_ISTAT); + + return (err < 0) ? err : 0; +} + +static int cis820x_config_intr(struct phy_device *phydev) +{ + int err; + + if(phydev->interrupts == PHY_INTERRUPT_ENABLED) + err = phy_write(phydev, MII_CIS8201_IMASK, + MII_CIS8201_IMASK_MASK); + else + err = phy_write(phydev, MII_CIS8201_IMASK, 0); + + return err; +} + +/* Cicada 820x */ +static struct phy_driver cis8204_driver = { + .phy_id = 0x000fc440, + .name = "Cicada Cis8204", + .phy_id_mask = 0x000fffc0, + .features = PHY_GBIT_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_init = &cis820x_config_init, + .config_aneg = &genphy_config_aneg, + .read_status = &genphy_read_status, + .ack_interrupt = &cis820x_ack_interrupt, + .config_intr = &cis820x_config_intr, + .driver = { .owner = THIS_MODULE,}, +}; + +static int __init cis8204_init(void) +{ + return phy_driver_register(&cis8204_driver); +} + +static void __exit cis8204_exit(void) +{ + phy_driver_unregister(&cis8204_driver); +} + +module_init(cis8204_init); +module_exit(cis8204_exit); diff --git a/drivers/net/phy/davicom.c b/drivers/net/phy/davicom.c new file mode 100644 index 0000000..6caf499 --- /dev/null +++ b/drivers/net/phy/davicom.c @@ -0,0 +1,195 @@ +/* + * drivers/net/phy/davicom.c + * + * Driver for Davicom PHYs + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#define MII_DM9161_SCR 0x10 +#define MII_DM9161_SCR_INIT 0x0610 + +/* DM9161 Interrupt Register */ +#define MII_DM9161_INTR 0x15 +#define MII_DM9161_INTR_PEND 0x8000 +#define MII_DM9161_INTR_DPLX_MASK 0x0800 +#define MII_DM9161_INTR_SPD_MASK 0x0400 +#define MII_DM9161_INTR_LINK_MASK 0x0200 +#define MII_DM9161_INTR_MASK 0x0100 +#define MII_DM9161_INTR_DPLX_CHANGE 0x0010 +#define MII_DM9161_INTR_SPD_CHANGE 0x0008 +#define MII_DM9161_INTR_LINK_CHANGE 0x0004 +#define MII_DM9161_INTR_INIT 0x0000 +#define MII_DM9161_INTR_STOP \ +(MII_DM9161_INTR_DPLX_MASK | MII_DM9161_INTR_SPD_MASK \ + | MII_DM9161_INTR_LINK_MASK | MII_DM9161_INTR_MASK) + +/* DM9161 10BT Configuration/Status */ +#define MII_DM9161_10BTCSR 0x12 +#define MII_DM9161_10BTCSR_INIT 0x7800 + +MODULE_DESCRIPTION("Davicom PHY driver"); +MODULE_AUTHOR("Andy Fleming"); +MODULE_LICENSE("GPL"); + + +#define DM9161_DELAY 1 +static int dm9161_config_intr(struct phy_device *phydev) +{ + int temp; + + temp = phy_read(phydev, MII_DM9161_INTR); + + if (temp < 0) + return temp; + + if(PHY_INTERRUPT_ENABLED == phydev->interrupts ) + temp &= ~(MII_DM9161_INTR_STOP); + else + temp |= MII_DM9161_INTR_STOP; + + temp = phy_write(phydev, MII_DM9161_INTR, temp); + + return temp; +} + +static int dm9161_config_aneg(struct phy_device *phydev) +{ + int err; + + /* Isolate the PHY */ + err = phy_write(phydev, MII_BMCR, BMCR_ISOLATE); + + if (err < 0) + return err; + + /* Configure the new settings */ + err = genphy_config_aneg(phydev); + + if (err < 0) + return err; + + return 0; +} + +static int dm9161_config_init(struct phy_device *phydev) +{ + int err; + + /* Isolate the PHY */ + err = phy_write(phydev, MII_BMCR, BMCR_ISOLATE); + + if (err < 0) + return err; + + /* Do not bypass the scrambler/descrambler */ + err = phy_write(phydev, MII_DM9161_SCR, MII_DM9161_SCR_INIT); + + if (err < 0) + return err; + + /* Clear 10BTCSR to default */ + err = phy_write(phydev, MII_DM9161_10BTCSR, MII_DM9161_10BTCSR_INIT); + + if (err < 0) + return err; + + /* Reconnect the PHY, and enable Autonegotiation */ + err = phy_write(phydev, MII_BMCR, BMCR_ANENABLE); + + if (err < 0) + return err; + + return 0; +} + +static int dm9161_ack_interrupt(struct phy_device *phydev) +{ + int err = phy_read(phydev, MII_DM9161_INTR); + + return (err < 0) ? err : 0; +} + +static struct phy_driver dm9161_driver = { + .phy_id = 0x0181b880, + .name = "Davicom DM9161E", + .phy_id_mask = 0x0ffffff0, + .features = PHY_BASIC_FEATURES, + .config_init = dm9161_config_init, + .config_aneg = dm9161_config_aneg, + .read_status = genphy_read_status, + .driver = { .owner = THIS_MODULE,}, +}; + +static struct phy_driver dm9131_driver = { + .phy_id = 0x00181b80, + .name = "Davicom DM9131", + .phy_id_mask = 0x0ffffff0, + .features = PHY_BASIC_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .ack_interrupt = dm9161_ack_interrupt, + .config_intr = dm9161_config_intr, + .driver = { .owner = THIS_MODULE,}, +}; + +static int __init davicom_init(void) +{ + int ret; + + ret = phy_driver_register(&dm9161_driver); + if (ret) + goto err1; + + ret = phy_driver_register(&dm9131_driver); + if (ret) + goto err2; + return 0; + + err2: + phy_driver_unregister(&dm9161_driver); + err1: + return ret; +} + +static void __exit davicom_exit(void) +{ + phy_driver_unregister(&dm9161_driver); + phy_driver_unregister(&dm9131_driver); +} + +module_init(davicom_init); +module_exit(davicom_exit); diff --git a/drivers/net/phy/lxt.c b/drivers/net/phy/lxt.c new file mode 100644 index 0000000..4c84044 --- /dev/null +++ b/drivers/net/phy/lxt.c @@ -0,0 +1,179 @@ +/* + * drivers/net/phy/lxt.c + * + * Driver for Intel LXT PHYs + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +/* The Level one LXT970 is used by many boards */ + +#define MII_LXT970_IER 17 /* Interrupt Enable Register */ + +#define MII_LXT970_IER_IEN 0x0002 + +#define MII_LXT970_ISR 18 /* Interrupt Status Register */ + +#define MII_LXT970_CONFIG 19 /* Configuration Register */ + +/* ------------------------------------------------------------------------- */ +/* The Level one LXT971 is used on some of my custom boards */ + +/* register definitions for the 971 */ +#define MII_LXT971_IER 18 /* Interrupt Enable Register */ +#define MII_LXT971_IER_IEN 0x00f2 + +#define MII_LXT971_ISR 19 /* Interrupt Status Register */ + + +MODULE_DESCRIPTION("Intel LXT PHY driver"); +MODULE_AUTHOR("Andy Fleming"); +MODULE_LICENSE("GPL"); + +static int lxt970_ack_interrupt(struct phy_device *phydev) +{ + int err; + + err = phy_read(phydev, MII_BMSR); + + if (err < 0) + return err; + + err = phy_read(phydev, MII_LXT970_ISR); + + if (err < 0) + return err; + + return 0; +} + +static int lxt970_config_intr(struct phy_device *phydev) +{ + int err; + + if(phydev->interrupts == PHY_INTERRUPT_ENABLED) + err = phy_write(phydev, MII_LXT970_IER, MII_LXT970_IER_IEN); + else + err = phy_write(phydev, MII_LXT970_IER, 0); + + return err; +} + +static int lxt970_config_init(struct phy_device *phydev) +{ + int err; + + err = phy_write(phydev, MII_LXT970_CONFIG, 0); + + return err; +} + + +static int lxt971_ack_interrupt(struct phy_device *phydev) +{ + int err = phy_read(phydev, MII_LXT971_ISR); + + if (err < 0) + return err; + + return 0; +} + +static int lxt971_config_intr(struct phy_device *phydev) +{ + int err; + + if(phydev->interrupts == PHY_INTERRUPT_ENABLED) + err = phy_write(phydev, MII_LXT971_IER, MII_LXT971_IER_IEN); + else + err = phy_write(phydev, MII_LXT971_IER, 0); + + return err; +} + +static struct phy_driver lxt970_driver = { + .phy_id = 0x07810000, + .name = "LXT970", + .phy_id_mask = 0x0fffffff, + .features = PHY_BASIC_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_init = lxt970_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .ack_interrupt = lxt970_ack_interrupt, + .config_intr = lxt970_config_intr, + .driver = { .owner = THIS_MODULE,}, +}; + +static struct phy_driver lxt971_driver = { + .phy_id = 0x0001378e, + .name = "LXT971", + .phy_id_mask = 0x0fffffff, + .features = PHY_BASIC_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .ack_interrupt = lxt971_ack_interrupt, + .config_intr = lxt971_config_intr, + .driver = { .owner = THIS_MODULE,}, +}; + +static int __init lxt_init(void) +{ + int ret; + + ret = phy_driver_register(&lxt970_driver); + if (ret) + goto err1; + + ret = phy_driver_register(&lxt971_driver); + if (ret) + goto err2; + return 0; + + err2: + phy_driver_unregister(&lxt970_driver); + err1: + return ret; +} + +static void __exit lxt_exit(void) +{ + phy_driver_unregister(&lxt970_driver); + phy_driver_unregister(&lxt971_driver); +} + +module_init(lxt_init); +module_exit(lxt_exit); diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c new file mode 100644 index 0000000..4a72b02 --- /dev/null +++ b/drivers/net/phy/marvell.c @@ -0,0 +1,140 @@ +/* + * drivers/net/phy/marvell.c + * + * Driver for Marvell PHYs + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#define MII_M1011_IEVENT 0x13 +#define MII_M1011_IEVENT_CLEAR 0x0000 + +#define MII_M1011_IMASK 0x12 +#define MII_M1011_IMASK_INIT 0x6400 +#define MII_M1011_IMASK_CLEAR 0x0000 + +MODULE_DESCRIPTION("Marvell PHY driver"); +MODULE_AUTHOR("Andy Fleming"); +MODULE_LICENSE("GPL"); + +static int marvell_ack_interrupt(struct phy_device *phydev) +{ + int err; + + /* Clear the interrupts by reading the reg */ + err = phy_read(phydev, MII_M1011_IEVENT); + + if (err < 0) + return err; + + return 0; +} + +static int marvell_config_intr(struct phy_device *phydev) +{ + int err; + + if(phydev->interrupts == PHY_INTERRUPT_ENABLED) + err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_INIT); + else + err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR); + + return err; +} + +static int marvell_config_aneg(struct phy_device *phydev) +{ + int err; + + /* The Marvell PHY has an errata which requires + * that certain registers get written in order + * to restart autonegotiation */ + err = phy_write(phydev, MII_BMCR, BMCR_RESET); + + if (err < 0) + return err; + + err = phy_write(phydev, 0x1d, 0x1f); + if (err < 0) + return err; + + err = phy_write(phydev, 0x1e, 0x200c); + if (err < 0) + return err; + + err = phy_write(phydev, 0x1d, 0x5); + if (err < 0) + return err; + + err = phy_write(phydev, 0x1e, 0); + if (err < 0) + return err; + + err = phy_write(phydev, 0x1e, 0x100); + if (err < 0) + return err; + + + err = genphy_config_aneg(phydev); + + return err; +} + + +static struct phy_driver m88e1101_driver = { + .phy_id = 0x01410c00, + .phy_id_mask = 0xffffff00, + .name = "Marvell 88E1101", + .features = PHY_GBIT_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_aneg = &marvell_config_aneg, + .read_status = &genphy_read_status, + .ack_interrupt = &marvell_ack_interrupt, + .config_intr = &marvell_config_intr, + .driver = { .owner = THIS_MODULE,}, +}; + +static int __init marvell_init(void) +{ + return phy_driver_register(&m88e1101_driver); +} + +static void __exit marvell_exit(void) +{ + phy_driver_unregister(&m88e1101_driver); +} + +module_init(marvell_init); +module_exit(marvell_exit); diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c new file mode 100644 index 0000000..e75103b --- /dev/null +++ b/drivers/net/phy/mdio_bus.c @@ -0,0 +1,173 @@ +/* + * drivers/net/phy/mdio_bus.c + * + * MDIO Bus interface + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +/* mdiobus_register + * + * description: Called by a bus driver to bring up all the PHYs + * on a given bus, and attach them to the bus + */ +int mdiobus_register(struct mii_bus *bus) +{ + int i; + int err = 0; + + spin_lock_init(&bus->mdio_lock); + + if (NULL == bus || NULL == bus->name || + NULL == bus->read || + NULL == bus->write) + return -EINVAL; + + if (bus->reset) + bus->reset(bus); + + for (i = 0; i < PHY_MAX_ADDR; i++) { + struct phy_device *phydev; + + phydev = get_phy_device(bus, i); + + if (IS_ERR(phydev)) + return PTR_ERR(phydev); + + /* There's a PHY at this address + * We need to set: + * 1) IRQ + * 2) bus_id + * 3) parent + * 4) bus + * 5) mii_bus + * And, we need to register it */ + if (phydev) { + phydev->irq = bus->irq[i]; + + phydev->dev.parent = bus->dev; + phydev->dev.bus = &mdio_bus_type; + sprintf(phydev->dev.bus_id, "phy%d:%d", bus->id, i); + + phydev->bus = bus; + + err = device_register(&phydev->dev); + + if (err) + printk(KERN_ERR "phy %d failed to register\n", + i); + } + + bus->phy_map[i] = phydev; + } + + pr_info("%s: probed\n", bus->name); + + return err; +} +EXPORT_SYMBOL(mdiobus_register); + +void mdiobus_unregister(struct mii_bus *bus) +{ + int i; + + for (i = 0; i < PHY_MAX_ADDR; i++) { + if (bus->phy_map[i]) { + device_unregister(&bus->phy_map[i]->dev); + kfree(bus->phy_map[i]); + } + } +} +EXPORT_SYMBOL(mdiobus_unregister); + +/* mdio_bus_match + * + * description: Given a PHY device, and a PHY driver, return 1 if + * the driver supports the device. Otherwise, return 0 + */ +static int mdio_bus_match(struct device *dev, struct device_driver *drv) +{ + struct phy_device *phydev = to_phy_device(dev); + struct phy_driver *phydrv = to_phy_driver(drv); + + return (phydrv->phy_id == (phydev->phy_id & phydrv->phy_id_mask)); +} + +/* Suspend and resume. Copied from platform_suspend and + * platform_resume + */ +static int mdio_bus_suspend(struct device * dev, u32 state) +{ + int ret = 0; + struct device_driver *drv = dev->driver; + + if (drv && drv->suspend) { + ret = drv->suspend(dev, state, SUSPEND_DISABLE); + if (ret == 0) + ret = drv->suspend(dev, state, SUSPEND_SAVE_STATE); + if (ret == 0) + ret = drv->suspend(dev, state, SUSPEND_POWER_DOWN); + } + return ret; +} + +static int mdio_bus_resume(struct device * dev) +{ + int ret = 0; + struct device_driver *drv = dev->driver; + + if (drv && drv->resume) { + ret = drv->resume(dev, RESUME_POWER_ON); + if (ret == 0) + ret = drv->resume(dev, RESUME_RESTORE_STATE); + if (ret == 0) + ret = drv->resume(dev, RESUME_ENABLE); + } + return ret; +} + +struct bus_type mdio_bus_type = { + .name = "mdio_bus", + .match = mdio_bus_match, + .suspend = mdio_bus_suspend, + .resume = mdio_bus_resume, +}; + +static int __init mdio_bus_init(void) +{ + return bus_register(&mdio_bus_type); +} + +subsys_initcall(mdio_bus_init); diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c new file mode 100644 index 0000000..e2c6896 --- /dev/null +++ b/drivers/net/phy/phy.c @@ -0,0 +1,862 @@ +/* + * drivers/net/phy/phy.c + * + * Framework for configuring and reading PHY devices + * Based on code in sungem_phy.c and gianfar_phy.c + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +static void phy_change(void *data); +static void phy_timer(unsigned long data); + +/* Convenience function to print out the current phy status + */ +void phy_print_status(struct phy_device *phydev) +{ + pr_info("%s: Link is %s", phydev->dev.bus_id, + phydev->link ? "Up" : "Down"); + if (phydev->link) + printk(" - %d/%s", phydev->speed, + DUPLEX_FULL == phydev->duplex ? + "Full" : "Half"); + + printk("\n"); +} +EXPORT_SYMBOL(phy_print_status); + + +/* Convenience functions for reading/writing a given PHY + * register. They MUST NOT be called from interrupt context, + * because the bus read/write functions may wait for an interrupt + * to conclude the operation. */ +int phy_read(struct phy_device *phydev, u16 regnum) +{ + int retval; + struct mii_bus *bus = phydev->bus; + + spin_lock_bh(&bus->mdio_lock); + retval = bus->read(bus, phydev->addr, regnum); + spin_unlock_bh(&bus->mdio_lock); + + return retval; +} +EXPORT_SYMBOL(phy_read); + +int phy_write(struct phy_device *phydev, u16 regnum, u16 val) +{ + int err; + struct mii_bus *bus = phydev->bus; + + spin_lock_bh(&bus->mdio_lock); + err = bus->write(bus, phydev->addr, regnum, val); + spin_unlock_bh(&bus->mdio_lock); + + return err; +} +EXPORT_SYMBOL(phy_write); + + +int phy_clear_interrupt(struct phy_device *phydev) +{ + int err = 0; + + if (phydev->drv->ack_interrupt) + err = phydev->drv->ack_interrupt(phydev); + + return err; +} + + +int phy_config_interrupt(struct phy_device *phydev, u32 interrupts) +{ + int err = 0; + + phydev->interrupts = interrupts; + if (phydev->drv->config_intr) + err = phydev->drv->config_intr(phydev); + + return err; +} + + +/* phy_aneg_done + * + * description: Reads the status register and returns 0 either if + * auto-negotiation is incomplete, or if there was an error. + * Returns BMSR_ANEGCOMPLETE if auto-negotiation is done. + */ +static inline int phy_aneg_done(struct phy_device *phydev) +{ + int retval; + + retval = phy_read(phydev, MII_BMSR); + + return (retval < 0) ? retval : (retval & BMSR_ANEGCOMPLETE); +} + +/* phy_start_aneg + * + * description: Calls the PHY driver's config_aneg, and then + * sets the PHY state to PHY_AN if auto-negotiation is enabled, + * and to PHY_FORCING if auto-negotiation is disabled. Unless + * the PHY is currently HALTED. + */ +int phy_start_aneg(struct phy_device *phydev) +{ + int err; + + spin_lock(&phydev->lock); + + if (AUTONEG_DISABLE == phydev->autoneg) + phy_sanitize_settings(phydev); + + err = phydev->drv->config_aneg(phydev); + + if (err < 0) + goto out_unlock; + + if (phydev->state != PHY_HALTED) { + if (AUTONEG_ENABLE == phydev->autoneg) { + phydev->state = PHY_AN; + phydev->link_timeout = PHY_AN_TIMEOUT; + } else { + phydev->state = PHY_FORCING; + phydev->link_timeout = PHY_FORCE_TIMEOUT; + } + } + +out_unlock: + spin_unlock(&phydev->lock); + return err; +} +EXPORT_SYMBOL(phy_start_aneg); + + +/* A structure for mapping a particular speed and duplex + * combination to a particular SUPPORTED and ADVERTISED value */ +struct phy_setting { + int speed; + int duplex; + u32 setting; +}; + +/* A mapping of all SUPPORTED settings to speed/duplex */ +static struct phy_setting settings[] = { + { + .speed = 10000, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_10000baseT_Full, + }, + { + .speed = SPEED_1000, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_1000baseT_Full, + }, + { + .speed = SPEED_1000, + .duplex = DUPLEX_HALF, + .setting = SUPPORTED_1000baseT_Half, + }, + { + .speed = SPEED_100, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_100baseT_Full, + }, + { + .speed = SPEED_100, + .duplex = DUPLEX_HALF, + .setting = SUPPORTED_100baseT_Half, + }, + { + .speed = SPEED_10, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_10baseT_Full, + }, + { + .speed = SPEED_10, + .duplex = DUPLEX_HALF, + .setting = SUPPORTED_10baseT_Half, + }, +}; + +#define MAX_NUM_SETTINGS (sizeof(settings)/sizeof(struct phy_setting)) + +/* phy_find_setting + * + * description: Searches the settings array for the setting which + * matches the desired speed and duplex, and returns the index + * of that setting. Returns the index of the last setting if + * none of the others match. + */ +static inline int phy_find_setting(int speed, int duplex) +{ + int idx = 0; + + while (idx < ARRAY_SIZE(settings) && + (settings[idx].speed != speed || + settings[idx].duplex != duplex)) + idx++; + + return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; +} + +/* phy_find_valid + * idx: The first index in settings[] to search + * features: A mask of the valid settings + * + * description: Returns the index of the first valid setting less + * than or equal to the one pointed to by idx, as determined by + * the mask in features. Returns the index of the last setting + * if nothing else matches. + */ +static inline int phy_find_valid(int idx, u32 features) +{ + while (idx < MAX_NUM_SETTINGS && !(settings[idx].setting & features)) + idx++; + + return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; +} + +/* phy_sanitize_settings + * + * description: Make sure the PHY is set to supported speeds and + * duplexes. Drop down by one in this order: 1000/FULL, + * 1000/HALF, 100/FULL, 100/HALF, 10/FULL, 10/HALF + */ +void phy_sanitize_settings(struct phy_device *phydev) +{ + u32 features = phydev->supported; + int idx; + + /* Sanitize settings based on PHY capabilities */ + if ((features & SUPPORTED_Autoneg) == 0) + phydev->autoneg = 0; + + idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex), + features); + + phydev->speed = settings[idx].speed; + phydev->duplex = settings[idx].duplex; +} +EXPORT_SYMBOL(phy_sanitize_settings); + +/* phy_force_reduction + * + * description: Reduces the speed/duplex settings by + * one notch. The order is so: + * 1000/FULL, 1000/HALF, 100/FULL, 100/HALF, + * 10/FULL, 10/HALF. The function bottoms out at 10/HALF. + */ +static void phy_force_reduction(struct phy_device *phydev) +{ + int idx; + + idx = phy_find_setting(phydev->speed, phydev->duplex); + + idx++; + + idx = phy_find_valid(idx, phydev->supported); + + phydev->speed = settings[idx].speed; + phydev->duplex = settings[idx].duplex; + + pr_info("Trying %d/%s\n", phydev->speed, + DUPLEX_FULL == phydev->duplex ? + "FULL" : "HALF"); +} + +/* phy_ethtool_sset: + * A generic ethtool sset function. Handles all the details + * + * A few notes about parameter checking: + * - We don't set port or transceiver, so we don't care what they + * were set to. + * - phy_start_aneg() will make sure forced settings are sane, and + * choose the next best ones from the ones selected, so we don't + * care if ethtool tries to give us bad values + */ +int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd) +{ + if (cmd->phy_address != phydev->addr) + return -EINVAL; + + /* We make sure that we don't pass unsupported + * values in to the PHY */ + cmd->advertising &= phydev->supported; + + /* Verify the settings we care about. */ + if (cmd->autoneg != AUTONEG_ENABLE && cmd->autoneg != AUTONEG_DISABLE) + return -EINVAL; + + if (cmd->autoneg == AUTONEG_ENABLE && cmd->advertising == 0) + return -EINVAL; + + if (cmd->autoneg == AUTONEG_DISABLE + && ((cmd->speed != SPEED_1000 + && cmd->speed != SPEED_100 + && cmd->speed != SPEED_10) + || (cmd->duplex != DUPLEX_HALF + && cmd->duplex != DUPLEX_FULL))) + return -EINVAL; + + phydev->autoneg = cmd->autoneg; + + phydev->speed = cmd->speed; + + phydev->advertising = cmd->advertising; + + if (AUTONEG_ENABLE == cmd->autoneg) + phydev->advertising |= ADVERTISED_Autoneg; + else + phydev->advertising &= ~ADVERTISED_Autoneg; + + phydev->duplex = cmd->duplex; + + /* Restart the PHY */ + phy_start_aneg(phydev); + + return 0; +} + +int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd) +{ + cmd->supported = phydev->supported; + + cmd->advertising = phydev->advertising; + + cmd->speed = phydev->speed; + cmd->duplex = phydev->duplex; + cmd->port = PORT_MII; + cmd->phy_address = phydev->addr; + cmd->transceiver = XCVR_EXTERNAL; + cmd->autoneg = phydev->autoneg; + + return 0; +} + + +/* Note that this function is currently incompatible with the + * PHYCONTROL layer. It changes registers without regard to + * current state. Use at own risk + */ +int phy_mii_ioctl(struct phy_device *phydev, + struct mii_ioctl_data *mii_data, int cmd) +{ + u16 val = mii_data->val_in; + + switch (cmd) { + case SIOCGMIIPHY: + mii_data->phy_id = phydev->addr; + break; + case SIOCGMIIREG: + mii_data->val_out = phy_read(phydev, mii_data->reg_num); + break; + + case SIOCSMIIREG: + if (!capable(CAP_NET_ADMIN)) + return -EPERM; + + if (mii_data->phy_id == phydev->addr) { + switch(mii_data->reg_num) { + case MII_BMCR: + if (val & (BMCR_RESET|BMCR_ANENABLE)) + phydev->autoneg = AUTONEG_DISABLE; + else + phydev->autoneg = AUTONEG_ENABLE; + if ((!phydev->autoneg) && (val & BMCR_FULLDPLX)) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + break; + case MII_ADVERTISE: + phydev->advertising = val; + break; + default: + /* do nothing */ + break; + } + } + + phy_write(phydev, mii_data->reg_num, val); + + if (mii_data->reg_num == MII_BMCR + && val & BMCR_RESET + && phydev->drv->config_init) + phydev->drv->config_init(phydev); + break; + } + + return 0; +} + +/* phy_start_machine: + * + * description: The PHY infrastructure can run a state machine + * which tracks whether the PHY is starting up, negotiating, + * etc. This function starts the timer which tracks the state + * of the PHY. If you want to be notified when the state + * changes, pass in the callback, otherwise, pass NULL. If you + * want to maintain your own state machine, do not call this + * function. */ +void phy_start_machine(struct phy_device *phydev, + void (*handler)(struct net_device *)) +{ + phydev->adjust_state = handler; + + init_timer(&phydev->phy_timer); + phydev->phy_timer.function = &phy_timer; + phydev->phy_timer.data = (unsigned long) phydev; + mod_timer(&phydev->phy_timer, jiffies + HZ); +} + +/* phy_stop_machine + * + * description: Stops the state machine timer, sets the state to + * UP (unless it wasn't up yet), and then frees the interrupt, + * if it is in use. This function must be called BEFORE + * phy_detach. + */ +void phy_stop_machine(struct phy_device *phydev) +{ + del_timer_sync(&phydev->phy_timer); + + spin_lock(&phydev->lock); + if (phydev->state > PHY_UP) + phydev->state = PHY_UP; + spin_unlock(&phydev->lock); + + if (phydev->irq != PHY_POLL) + phy_stop_interrupts(phydev); + + phydev->adjust_state = NULL; +} + +#ifdef CONFIG_PHYCONTROL +/* phy_error: + * + * Moves the PHY to the HALTED state in response to a read + * or write error, and tells the controller the link is down. + * Must not be called from interrupt context, or while the + * phydev->lock is held. + */ +void phy_error(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + phydev->state = PHY_HALTED; + spin_unlock(&phydev->lock); +} + +/* phy_interrupt + * + * description: When a PHY interrupt occurs, the handler disables + * interrupts, and schedules a work task to clear the interrupt. + */ +static irqreturn_t phy_interrupt(int irq, void *phy_dat, struct pt_regs *regs) +{ + struct phy_device *phydev = phy_dat; + + /* The MDIO bus is not allowed to be written in interrupt + * context, so we need to disable the irq here. A work + * queue will write the PHY to disable and clear the + * interrupt, and then reenable the irq line. */ + disable_irq_nosync(irq); + + schedule_work(&phydev->phy_queue); + + return IRQ_HANDLED; +} + +/* Enable the interrupts from the PHY side */ +int phy_enable_interrupts(struct phy_device *phydev) +{ + int err; + + err = phy_clear_interrupt(phydev); + + if (err < 0) + return err; + + err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); + + return err; +} +EXPORT_SYMBOL(phy_enable_interrupts); + +/* Disable the PHY interrupts from the PHY side */ +int phy_disable_interrupts(struct phy_device *phydev) +{ + int err; + + /* Disable PHY interrupts */ + err = phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); + + if (err) + goto phy_err; + + /* Clear the interrupt */ + err = phy_clear_interrupt(phydev); + + if (err) + goto phy_err; + + return 0; + +phy_err: + phy_error(phydev); + + return err; +} +EXPORT_SYMBOL(phy_disable_interrupts); + +/* phy_start_interrupts + * + * description: Request the interrupt for the given PHY. If + * this fails, then we set irq to PHY_POLL. + * Otherwise, we enable the interrupts in the PHY. + * Returns 0 on success. + * This should only be called with a valid IRQ number. + */ +int phy_start_interrupts(struct phy_device *phydev) +{ + int err = 0; + + INIT_WORK(&phydev->phy_queue, phy_change, phydev); + + if (request_irq(phydev->irq, phy_interrupt, + SA_SHIRQ, + "phy_interrupt", + phydev) < 0) { + printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n", + phydev->bus->name, + phydev->irq); + phydev->irq = PHY_POLL; + return 0; + } + + err = phy_enable_interrupts(phydev); + + return err; +} +EXPORT_SYMBOL(phy_start_interrupts); + +int phy_stop_interrupts(struct phy_device *phydev) +{ + int err; + + err = phy_disable_interrupts(phydev); + + if (err) + phy_error(phydev); + + free_irq(phydev->irq, phydev); + + return err; +} +EXPORT_SYMBOL(phy_stop_interrupts); + + +/* Scheduled by the phy_interrupt/timer to handle PHY changes */ +static void phy_change(void *data) +{ + int err; + struct phy_device *phydev = data; + + err = phy_disable_interrupts(phydev); + + if (err) + goto phy_err; + + spin_lock(&phydev->lock); + if ((PHY_RUNNING == phydev->state) || (PHY_NOLINK == phydev->state)) + phydev->state = PHY_CHANGELINK; + spin_unlock(&phydev->lock); + + enable_irq(phydev->irq); + + /* Reenable interrupts */ + err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); + + if (err) + goto irq_enable_err; + + return; + +irq_enable_err: + disable_irq(phydev->irq); +phy_err: + phy_error(phydev); +} + +/* Bring down the PHY link, and stop checking the status. */ +void phy_stop(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + + if (PHY_HALTED == phydev->state) + goto out_unlock; + + if (phydev->irq != PHY_POLL) { + /* Clear any pending interrupts */ + phy_clear_interrupt(phydev); + + /* Disable PHY Interrupts */ + phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); + } + + phydev->state = PHY_HALTED; + +out_unlock: + spin_unlock(&phydev->lock); +} + + +/* phy_start + * + * description: Indicates the attached device's readiness to + * handle PHY-related work. Used during startup to start the + * PHY, and after a call to phy_stop() to resume operation. + * Also used to indicate the MDIO bus has cleared an error + * condition. + */ +void phy_start(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + + switch (phydev->state) { + case PHY_STARTING: + phydev->state = PHY_PENDING; + break; + case PHY_READY: + phydev->state = PHY_UP; + break; + case PHY_HALTED: + phydev->state = PHY_RESUMING; + default: + break; + } + spin_unlock(&phydev->lock); +} +EXPORT_SYMBOL(phy_stop); +EXPORT_SYMBOL(phy_start); + +/* PHY timer which handles the state machine */ +static void phy_timer(unsigned long data) +{ + struct phy_device *phydev = (struct phy_device *)data; + int needs_aneg = 0; + int err = 0; + + spin_lock(&phydev->lock); + + if (phydev->adjust_state) + phydev->adjust_state(phydev->attached_dev); + + switch(phydev->state) { + case PHY_DOWN: + case PHY_STARTING: + case PHY_READY: + case PHY_PENDING: + break; + case PHY_UP: + needs_aneg = 1; + + phydev->link_timeout = PHY_AN_TIMEOUT; + + break; + case PHY_AN: + /* Check if negotiation is done. Break + * if there's an error */ + err = phy_aneg_done(phydev); + if (err < 0) + break; + + /* If auto-negotiation is done, we change to + * either RUNNING, or NOLINK */ + if (err > 0) { + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + } else { + phydev->state = PHY_NOLINK; + netif_carrier_off(phydev->attached_dev); + } + + phydev->adjust_link(phydev->attached_dev); + + } else if (0 == phydev->link_timeout--) { + /* The counter expired, so either we + * switch to forced mode, or the + * magic_aneg bit exists, and we try aneg + * again */ + if (!(phydev->drv->flags & PHY_HAS_MAGICANEG)) { + int idx; + + /* We'll start from the + * fastest speed, and work + * our way down */ + idx = phy_find_valid(0, + phydev->supported); + + phydev->speed = settings[idx].speed; + phydev->duplex = settings[idx].duplex; + + phydev->autoneg = AUTONEG_DISABLE; + phydev->state = PHY_FORCING; + phydev->link_timeout = + PHY_FORCE_TIMEOUT; + + pr_info("Trying %d/%s\n", + phydev->speed, + DUPLEX_FULL == + phydev->duplex ? + "FULL" : "HALF"); + } + + needs_aneg = 1; + } + break; + case PHY_NOLINK: + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + phydev->adjust_link(phydev->attached_dev); + } + break; + case PHY_FORCING: + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + } else { + if (0 == phydev->link_timeout--) { + phy_force_reduction(phydev); + needs_aneg = 1; + } + } + + phydev->adjust_link(phydev->attached_dev); + break; + case PHY_RUNNING: + /* Only register a CHANGE if we are + * polling */ + if (PHY_POLL == phydev->irq) + phydev->state = PHY_CHANGELINK; + break; + case PHY_CHANGELINK: + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + } else { + phydev->state = PHY_NOLINK; + netif_carrier_off(phydev->attached_dev); + } + + phydev->adjust_link(phydev->attached_dev); + + if (PHY_POLL != phydev->irq) + err = phy_config_interrupt(phydev, + PHY_INTERRUPT_ENABLED); + break; + case PHY_HALTED: + if (phydev->link) { + phydev->link = 0; + netif_carrier_off(phydev->attached_dev); + phydev->adjust_link(phydev->attached_dev); + } + break; + case PHY_RESUMING: + + err = phy_clear_interrupt(phydev); + + if (err) + break; + + err = phy_config_interrupt(phydev, + PHY_INTERRUPT_ENABLED); + + if (err) + break; + + if (AUTONEG_ENABLE == phydev->autoneg) { + err = phy_aneg_done(phydev); + if (err < 0) + break; + + /* err > 0 if AN is done. + * Otherwise, it's 0, and we're + * still waiting for AN */ + if (err > 0) { + phydev->state = PHY_RUNNING; + } else { + phydev->state = PHY_AN; + phydev->link_timeout = PHY_AN_TIMEOUT; + } + } else + phydev->state = PHY_RUNNING; + break; + } + + spin_unlock(&phydev->lock); + + if (needs_aneg) + err = phy_start_aneg(phydev); + + if (err < 0) + phy_error(phydev); + + mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ); +} + +#endif /* CONFIG_PHYCONTROL */ diff --git a/drivers/net/phy/phy.c.orig b/drivers/net/phy/phy.c.orig new file mode 100644 index 0000000..6af17ce --- /dev/null +++ b/drivers/net/phy/phy.c.orig @@ -0,0 +1,860 @@ +/* + * drivers/net/phy/phy.c + * + * Framework for configuring and reading PHY devices + * Based on code in sungem_phy.c and gianfar_phy.c + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +static void phy_change(void *data); +static void phy_timer(unsigned long data); + +/* Convenience function to print out the current phy status + */ +void phy_print_status(struct phy_device *phydev) +{ + pr_info("%s: Link is %s", phydev->dev.bus_id, + phydev->link ? "Up" : "Down"); + if (phydev->link) + printk(" - %d/%s", phydev->speed, + DUPLEX_FULL == phydev->duplex ? + "Full" : "Half"); + + printk("\n"); +} +EXPORT_SYMBOL(phy_print_status); + + +/* Convenience functions for reading/writing a given PHY + * register. They MUST NOT be called from interrupt context, + * because the bus read/write functions may wait for an interrupt + * to conclude the operation. */ +int phy_read(struct phy_device *phydev, u16 regnum) +{ + int retval; + struct mii_bus *bus = phydev->bus; + + spin_lock_bh(&bus->mdio_lock); + retval = bus->read(bus, phydev->addr, regnum); + spin_unlock_bh(&bus->mdio_lock); + + return retval; +} +EXPORT_SYMBOL(phy_read); + +int phy_write(struct phy_device *phydev, u16 regnum, u16 val) +{ + int err; + struct mii_bus *bus = phydev->bus; + + spin_lock_bh(&bus->mdio_lock); + err = bus->write(bus, phydev->addr, regnum, val); + spin_unlock_bh(&bus->mdio_lock); + + return err; +} +EXPORT_SYMBOL(phy_write); + + +int phy_clear_interrupt(struct phy_device *phydev) +{ + int err = 0; + + if (phydev->drv->ack_interrupt) + err = phydev->drv->ack_interrupt(phydev); + + return err; +} + + +int phy_config_interrupt(struct phy_device *phydev, u32 interrupts) +{ + int err = 0; + + phydev->interrupts = interrupts; + if (phydev->drv->config_intr) + err = phydev->drv->config_intr(phydev); + + return err; +} + + +/* phy_aneg_done + * + * description: Reads the status register and returns 0 either if + * auto-negotiation is incomplete, or if there was an error. + * Returns BMSR_ANEGCOMPLETE if auto-negotiation is done. + */ +static inline int phy_aneg_done(struct phy_device *phydev) +{ + int retval; + + retval = phy_read(phydev, MII_BMSR); + + return (retval < 0) ? retval : (retval & BMSR_ANEGCOMPLETE); +} + +/* phy_start_aneg + * + * description: Calls the PHY driver's config_aneg, and then + * sets the PHY state to PHY_AN if auto-negotiation is enabled, + * and to PHY_FORCING if auto-negotiation is disabled. Unless + * the PHY is currently HALTED. + */ +int phy_start_aneg(struct phy_device *phydev) +{ + int err; + + spin_lock(&phydev->lock); + + if (AUTONEG_DISABLE == phydev->autoneg) + phy_sanitize_settings(phydev); + + err = phydev->drv->config_aneg(phydev); + + if (err < 0) + goto out_unlock; + + if (phydev->state != PHY_HALTED) { + if (AUTONEG_ENABLE == phydev->autoneg) { + phydev->state = PHY_AN; + phydev->link_timeout = PHY_AN_TIMEOUT; + } else { + phydev->state = PHY_FORCING; + phydev->link_timeout = PHY_FORCE_TIMEOUT; + } + } + +out_unlock: + spin_unlock(&phydev->lock); + return err; +} +EXPORT_SYMBOL(phy_start_aneg); + + +/* A structure for mapping a particular speed and duplex + * combination to a particular SUPPORTED and ADVERTISED value */ +struct phy_setting { + int speed; + int duplex; + u32 setting; +}; + +/* A mapping of all SUPPORTED settings to speed/duplex */ +static struct phy_setting settings[] = { + { + .speed = 10000, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_10000baseT_Full, + }, + { + .speed = SPEED_1000, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_1000baseT_Full, + }, + { + .speed = SPEED_1000, + .duplex = DUPLEX_HALF, + .setting = SUPPORTED_1000baseT_Half, + }, + { + .speed = SPEED_100, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_100baseT_Full, + }, + { + .speed = SPEED_100, + .duplex = DUPLEX_HALF, + .setting = SUPPORTED_100baseT_Half, + }, + { + .speed = SPEED_10, + .duplex = DUPLEX_FULL, + .setting = SUPPORTED_10baseT_Full, + }, + { + .speed = SPEED_10, + .duplex = DUPLEX_HALF, + .setting = SUPPORTED_10baseT_Half, + }, +}; + +#define MAX_NUM_SETTINGS (sizeof(settings)/sizeof(struct phy_setting)) + +/* phy_find_setting + * + * description: Searches the settings array for the setting which + * matches the desired speed and duplex, and returns the index + * of that setting. Returns the index of the last setting if + * none of the others match. + */ +static inline int phy_find_setting(int speed, int duplex) +{ + int idx = 0; + + while (idx < ARRAY_SIZE(settings) && + (settings[idx].speed != speed || + settings[idx].duplex != duplex)) + idx++; + + return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; +} + +/* phy_find_valid + * idx: The first index in settings[] to search + * features: A mask of the valid settings + * + * description: Returns the index of the first valid setting less + * than or equal to the one pointed to by idx, as determined by + * the mask in features. Returns the index of the last setting + * if nothing else matches. + */ +static inline int phy_find_valid(int idx, u32 features) +{ + while (idx < MAX_NUM_SETTINGS && !(settings[idx].setting & features)) + idx++; + + return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; +} + +/* phy_sanitize_settings + * + * description: Make sure the PHY is set to supported speeds and + * duplexes. Drop down by one in this order: 1000/FULL, + * 1000/HALF, 100/FULL, 100/HALF, 10/FULL, 10/HALF + */ +void phy_sanitize_settings(struct phy_device *phydev) +{ + u32 features = phydev->supported; + int idx; + + /* Sanitize settings based on PHY capabilities */ + if ((features & SUPPORTED_Autoneg) == 0) + phydev->autoneg = 0; + + idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex), + features); + + phydev->speed = settings[idx].speed; + phydev->duplex = settings[idx].duplex; +} +EXPORT_SYMBOL(phy_sanitize_settings); + +/* phy_force_reduction + * + * description: Reduces the speed/duplex settings by + * one notch. The order is so: + * 1000/FULL, 1000/HALF, 100/FULL, 100/HALF, + * 10/FULL, 10/HALF. The function bottoms out at 10/HALF. + */ +static void phy_force_reduction(struct phy_device *phydev) +{ + int idx; + + idx = phy_find_setting(phydev->speed, phydev->duplex); + + idx++; + + idx = phy_find_valid(idx, phydev->supported); + + phydev->speed = settings[idx].speed; + phydev->duplex = settings[idx].duplex; + + pr_info("Trying %d/%s\n", phydev->speed, + DUPLEX_FULL == phydev->duplex ? + "FULL" : "HALF"); +} + +/* phy_ethtool_sset: + * A generic ethtool sset function. Handles all the details + * + * A few notes about parameter checking: + * - We don't set port or transceiver, so we don't care what they + * were set to. + * - phy_start_aneg() will make sure forced settings are sane, and + * choose the next best ones from the ones selected, so we don't + * care if ethtool tries to give us bad values + */ +int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd) +{ + if (cmd->phy_address != phydev->addr) + return -EINVAL; + + /* We make sure that we don't pass unsupported + * values in to the PHY */ + cmd->advertising &= phydev->supported; + + /* Verify the settings we care about. */ + if (cmd->autoneg != AUTONEG_ENABLE && cmd->autoneg != AUTONEG_DISABLE) + return -EINVAL; + + if (cmd->autoneg == AUTONEG_ENABLE && cmd->advertising == 0) + return -EINVAL; + + if (cmd->autoneg == AUTONEG_DISABLE + && ((cmd->speed != SPEED_1000 + && cmd->speed != SPEED_100 + && cmd->speed != SPEED_10) + || (cmd->duplex != DUPLEX_HALF + && cmd->duplex != DUPLEX_FULL))) + return -EINVAL; + + phydev->autoneg = cmd->autoneg; + + phydev->speed = cmd->speed; + + phydev->advertising = cmd->advertising; + + if (AUTONEG_ENABLE == cmd->autoneg) + phydev->advertising |= ADVERTISED_Autoneg; + else + phydev->advertising &= ~ADVERTISED_Autoneg; + + phydev->duplex = cmd->duplex; + + /* Restart the PHY */ + phy_start_aneg(phydev); + + return 0; +} + +int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd) +{ + cmd->supported = phydev->supported; + + cmd->advertising = phydev->advertising; + + cmd->speed = phydev->speed; + cmd->duplex = phydev->duplex; + cmd->port = PORT_MII; + cmd->phy_address = phydev->addr; + cmd->transceiver = XCVR_EXTERNAL; + cmd->autoneg = phydev->autoneg; + + return 0; +} + + +/* Note that this function is currently incompatible with the + * PHYCONTROL layer. It changes registers without regard to + * current state. Use at own risk + */ +int phy_mii_ioctl(struct phy_device *phydev, + struct mii_ioctl_data *mii_data, int cmd) +{ + u16 val = mii_data->val_in; + + switch (cmd) { + case SIOCGMIIPHY: + mii_data->phy_id = phydev->addr; + break; + case SIOCGMIIREG: + mii_data->val_out = phy_read(phydev, mii_data->reg_num); + break; + + case SIOCSMIIREG: + if (!capable(CAP_NET_ADMIN)) + return -EPERM; + + if (mii_data->phy_id == phydev->addr) { + switch(mii_data->reg_num) { + case MII_BMCR: + if (val & (BMCR_RESET|BMCR_ANENABLE)) + phydev->autoneg = AUTONEG_DISABLE; + else + phydev->autoneg = AUTONEG_ENABLE; + if ((!phydev->autoneg) && (val & BMCR_FULLDPLX)) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + break; + case MII_ADVERTISE: + phydev->advertising = val; + break; + default: + /* do nothing */ + break; + } + } + + phy_write(phydev, mii_data->reg_num, val); + + if (mii_data->reg_num == MII_BMCR + && val & BMCR_RESET + && phydev->drv->config_init) + phydev->drv->config_init(phydev); + break; + } + + return 0; +} + +/* phy_start_machine: + * + * description: The PHY infrastructure can run a state machine + * which tracks whether the PHY is starting up, negotiating, + * etc. This function starts the timer which tracks the state + * of the PHY. If you want to be notified when the state + * changes, pass in the callback, otherwise, pass NULL. If you + * want to maintain your own state machine, do not call this + * function. */ +void phy_start_machine(struct phy_device *phydev, + void (*handler)(struct net_device *)) +{ + phydev->adjust_state = handler; + + init_timer(&phydev->phy_timer); + phydev->phy_timer.function = &phy_timer; + phydev->phy_timer.data = (unsigned long) phydev; + mod_timer(&phydev->phy_timer, jiffies + HZ); +} + +/* phy_stop_machine + * + * description: Stops the state machine timer, sets the state to + * UP (unless it wasn't up yet), and then frees the interrupt, + * if it is in use. This function must be called BEFORE + * phy_detach. + */ +void phy_stop_machine(struct phy_device *phydev) +{ + del_timer_sync(&phydev->phy_timer); + + spin_lock(&phydev->lock); + if (phydev->state > PHY_UP) + phydev->state = PHY_UP; + spin_unlock(&phydev->lock); + + if (phydev->irq != PHY_POLL) + phy_stop_interrupts(phydev); + + phydev->adjust_state = NULL; +} + +#ifdef CONFIG_PHYCONTROL +/* phy_error: + * + * Moves the PHY to the HALTED state in response to a read + * or write error, and tells the controller the link is down. + * Must not be called from interrupt context, or while the + * phydev->lock is held. + */ +void phy_error(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + phydev->state = PHY_HALTED; + spin_unlock(&phydev->lock); +} + +/* phy_interrupt + * + * description: When a PHY interrupt occurs, the handler disables + * interrupts, and schedules a work task to clear the interrupt. + */ +static irqreturn_t phy_interrupt(int irq, void *phy_dat, struct pt_regs *regs) +{ + struct phy_device *phydev = phy_dat; + + /* The MDIO bus is not allowed to be written in interrupt + * context, so we need to disable the irq here. A work + * queue will write the PHY to disable and clear the + * interrupt, and then reenable the irq line. */ + disable_irq_nosync(irq); + + schedule_work(&phydev->phy_queue); + + return IRQ_HANDLED; +} + +/* Enable the interrupts from the PHY side */ +int phy_enable_interrupts(struct phy_device *phydev) +{ + int err; + + err = phy_clear_interrupt(phydev); + + if (err < 0) + return err; + + err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); + + return err; +} + +/* Disable the PHY interrupts from the PHY side */ +int phy_disable_interrupts(struct phy_device *phydev) +{ + int err; + + /* Disable PHY interrupts */ + err = phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); + + if (err) + goto phy_err; + + /* Clear the interrupt */ + err = phy_clear_interrupt(phydev); + + if (err) + goto phy_err; + + return 0; + +phy_err: + phy_error(phydev); + + return err; +} + +/* phy_start_interrupts + * + * description: Request the interrupt for the given PHY. If + * this fails, then we set irq to PHY_POLL. + * Otherwise, we enable the interrupts in the PHY. + * Returns 0 on success. + * This should only be called with a valid IRQ number. + */ +int phy_start_interrupts(struct phy_device *phydev) +{ + int err = 0; + + INIT_WORK(&phydev->phy_queue, phy_change, phydev); + + if (request_irq(phydev->irq, phy_interrupt, + SA_SHIRQ, + "phy_interrupt", + phydev) < 0) { + printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n", + phydev->bus->name, + phydev->irq); + phydev->irq = PHY_POLL; + return 0; + } + + err = phy_enable_interrupts(phydev); + + return err; +} +EXPORT_SYMBOL(phy_start_interrupts); + +int phy_stop_interrupts(struct phy_device *phydev) +{ + int err; + + err = phy_disable_interrupts(phydev); + + if (err) + phy_error(phydev); + + free_irq(phydev->irq, phydev); + + return err; +} +EXPORT_SYMBOL(phy_stop_interrupts); + + +/* Scheduled by the phy_interrupt/timer to handle PHY changes */ +static void phy_change(void *data) +{ + int err; + struct phy_device *phydev = data; + + err = phy_disable_interrupts(phydev); + + if (err) + goto phy_err; + + spin_lock(&phydev->lock); + if ((PHY_RUNNING == phydev->state) || (PHY_NOLINK == phydev->state)) + phydev->state = PHY_CHANGELINK; + spin_unlock(&phydev->lock); + + enable_irq(phydev->irq); + + /* Reenable interrupts */ + err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); + + if (err) + goto irq_enable_err; + + return; + +irq_enable_err: + disable_irq(phydev->irq); +phy_err: + phy_error(phydev); +} + +/* Bring down the PHY link, and stop checking the status. */ +void phy_stop(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + + if (PHY_HALTED == phydev->state) + goto out_unlock; + + if (phydev->irq != PHY_POLL) { + /* Clear any pending interrupts */ + phy_clear_interrupt(phydev); + + /* Disable PHY Interrupts */ + phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); + } + + phydev->state = PHY_HALTED; + +out_unlock: + spin_unlock(&phydev->lock); +} + + +/* phy_start + * + * description: Indicates the attached device's readiness to + * handle PHY-related work. Used during startup to start the + * PHY, and after a call to phy_stop() to resume operation. + * Also used to indicate the MDIO bus has cleared an error + * condition. + */ +void phy_start(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + + switch (phydev->state) { + case PHY_STARTING: + phydev->state = PHY_PENDING; + break; + case PHY_READY: + phydev->state = PHY_UP; + break; + case PHY_HALTED: + phydev->state = PHY_RESUMING; + default: + break; + } + spin_unlock(&phydev->lock); +} +EXPORT_SYMBOL(phy_stop); +EXPORT_SYMBOL(phy_start); + +/* PHY timer which handles the state machine */ +static void phy_timer(unsigned long data) +{ + struct phy_device *phydev = (struct phy_device *)data; + int needs_aneg = 0; + int err = 0; + + spin_lock(&phydev->lock); + + if (phydev->adjust_state) + phydev->adjust_state(phydev->attached_dev); + + switch(phydev->state) { + case PHY_DOWN: + case PHY_STARTING: + case PHY_READY: + case PHY_PENDING: + break; + case PHY_UP: + needs_aneg = 1; + + phydev->link_timeout = PHY_AN_TIMEOUT; + + break; + case PHY_AN: + /* Check if negotiation is done. Break + * if there's an error */ + err = phy_aneg_done(phydev); + if (err < 0) + break; + + /* If auto-negotiation is done, we change to + * either RUNNING, or NOLINK */ + if (err > 0) { + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + } else { + phydev->state = PHY_NOLINK; + netif_carrier_off(phydev->attached_dev); + } + + phydev->adjust_link(phydev->attached_dev); + + } else if (0 == phydev->link_timeout--) { + /* The counter expired, so either we + * switch to forced mode, or the + * magic_aneg bit exists, and we try aneg + * again */ + if (!(phydev->drv->flags & PHY_HAS_MAGICANEG)) { + int idx; + + /* We'll start from the + * fastest speed, and work + * our way down */ + idx = phy_find_valid(0, + phydev->supported); + + phydev->speed = settings[idx].speed; + phydev->duplex = settings[idx].duplex; + + phydev->autoneg = AUTONEG_DISABLE; + phydev->state = PHY_FORCING; + phydev->link_timeout = + PHY_FORCE_TIMEOUT; + + pr_info("Trying %d/%s\n", + phydev->speed, + DUPLEX_FULL == + phydev->duplex ? + "FULL" : "HALF"); + } + + needs_aneg = 1; + } + break; + case PHY_NOLINK: + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + phydev->adjust_link(phydev->attached_dev); + } + break; + case PHY_FORCING: + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + } else { + if (0 == phydev->link_timeout--) { + phy_force_reduction(phydev); + needs_aneg = 1; + } + } + + phydev->adjust_link(phydev->attached_dev); + break; + case PHY_RUNNING: + /* Only register a CHANGE if we are + * polling */ + if (PHY_POLL == phydev->irq) + phydev->state = PHY_CHANGELINK; + break; + case PHY_CHANGELINK: + err = phy_read_status(phydev); + + if (err) + break; + + if (phydev->link) { + phydev->state = PHY_RUNNING; + netif_carrier_on(phydev->attached_dev); + } else { + phydev->state = PHY_NOLINK; + netif_carrier_off(phydev->attached_dev); + } + + phydev->adjust_link(phydev->attached_dev); + + if (PHY_POLL != phydev->irq) + err = phy_config_interrupt(phydev, + PHY_INTERRUPT_ENABLED); + break; + case PHY_HALTED: + if (phydev->link) { + phydev->link = 0; + netif_carrier_off(phydev->attached_dev); + phydev->adjust_link(phydev->attached_dev); + } + break; + case PHY_RESUMING: + + err = phy_clear_interrupt(phydev); + + if (err) + break; + + err = phy_config_interrupt(phydev, + PHY_INTERRUPT_ENABLED); + + if (err) + break; + + if (AUTONEG_ENABLE == phydev->autoneg) { + err = phy_aneg_done(phydev); + if (err < 0) + break; + + /* err > 0 if AN is done. + * Otherwise, it's 0, and we're + * still waiting for AN */ + if (err > 0) { + phydev->state = PHY_RUNNING; + } else { + phydev->state = PHY_AN; + phydev->link_timeout = PHY_AN_TIMEOUT; + } + } else + phydev->state = PHY_RUNNING; + break; + } + + spin_unlock(&phydev->lock); + + if (needs_aneg) + err = phy_start_aneg(phydev); + + if (err < 0) + phy_error(phydev); + + mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ); +} + +#endif /* CONFIG_PHYCONTROL */ diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c new file mode 100644 index 0000000..f0595af --- /dev/null +++ b/drivers/net/phy/phy_device.c @@ -0,0 +1,682 @@ +/* + * drivers/net/phy/phy_device.c + * + * Framework for finding and configuring PHYs. + * Also contains generic PHY driver + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +/* get_phy_device + * + * description: Reads the ID registers of the PHY at addr on the + * bus, then allocates and returns the phy_device to + * represent it. + */ +struct phy_device * get_phy_device(struct mii_bus *bus, int addr) +{ + int phy_reg; + u32 phy_id; + struct phy_device *dev = NULL; + + /* Grab the bits from PHYIR1, and put them + * in the upper half */ + phy_reg = bus->read(bus, addr, MII_PHYSID1); + + if (phy_reg < 0) + return ERR_PTR(phy_reg); + + phy_id = (phy_reg & 0xffff) << 16; + + /* Grab the bits from PHYIR2, and put them in the lower half */ + phy_reg = bus->read(bus, addr, MII_PHYSID2); + + if (phy_reg < 0) + return ERR_PTR(phy_reg); + + phy_id |= (phy_reg & 0xffff); + + /* If the phy_id is all Fs, there is no device there */ + if (0xffffffff == phy_id) + return NULL; + + /* Otherwise, we allocate the device, and initialize the + * default values */ + dev = kcalloc(1, sizeof(*dev), GFP_KERNEL); + + if (NULL == dev) + return ERR_PTR(-ENOMEM); + + dev->speed = 0; + dev->duplex = -1; + dev->pause = dev->asym_pause = 0; + dev->link = 1; + + dev->autoneg = AUTONEG_ENABLE; + + dev->addr = addr; + dev->phy_id = phy_id; + dev->bus = bus; + + dev->state = PHY_DOWN; + + spin_lock_init(&dev->lock); + + return dev; +} + +/* phy_prepare_link: + * + * description: Tells the PHY infrastructure to handle the + * gory details on monitoring link status (whether through + * polling or an interrupt), and to call back to the + * connected device driver when the link status changes. + * If you want to monitor your own link state, don't call + * this function */ +void phy_prepare_link(struct phy_device *phydev, + void (*handler)(struct net_device *)) +{ + phydev->adjust_link = handler; +} + +#ifdef CONFIG_PHYCONTROL +/* phy_connect: + * + * description: Convenience function for connecting ethernet + * devices to PHY devices. The default behavior is for + * the PHY infrastructure to handle everything, and only notify + * the connected driver when the link status changes. If you + * don't want, or can't use the provided functionality, you may + * choose to call only the subset of functions which provide + * the desired functionality. + */ +struct phy_device * phy_connect(struct net_device *dev, const char *phy_id, + void (*handler)(struct net_device *), u32 flags) +{ + struct phy_device *phydev; + + phydev = phy_attach(dev, phy_id, flags); + + if (IS_ERR(phydev)) + return phydev; + + phy_prepare_link(phydev, handler); + + phy_start_machine(phydev, NULL); + + if (phydev->irq > 0) + phy_start_interrupts(phydev); + + return phydev; +} +EXPORT_SYMBOL(phy_connect); + +void phy_disconnect(struct phy_device *phydev) +{ + if (phydev->irq > 0) + phy_stop_interrupts(phydev); + + phy_stop_machine(phydev); + + phydev->adjust_link = NULL; + + phy_detach(phydev); +} +EXPORT_SYMBOL(phy_disconnect); + +#endif /* CONFIG_PHYCONTROL */ + +/* phy_attach: + * + * description: Called by drivers to attach to a particular PHY + * device. The phy_device is found, and properly hooked up + * to the phy_driver. If no driver is attached, then the + * genphy_driver is used. The phy_device is given a ptr to + * the attaching device, and given a callback for link status + * change. The phy_device is returned to the attaching + * driver. + */ +static int phy_compare_id(struct device *dev, void *data) +{ + return strcmp((char *)data, dev->bus_id) ? 0 : 1; +} + +struct phy_device *phy_attach(struct net_device *dev, + const char *phy_id, u32 flags) +{ + struct bus_type *bus = &mdio_bus_type; + struct phy_device *phydev; + struct device *d; + + /* Search the list of PHY devices on the mdio bus for the + * PHY with the requested name */ + d = bus_find_device(bus, NULL, (void *)phy_id, phy_compare_id); + + if (d) { + phydev = to_phy_device(d); + } else { + printk(KERN_ERR "%s not found\n", phy_id); + return ERR_PTR(-ENODEV); + } + + /* Assume that if there is no driver, that it doesn't + * exist, and we should use the genphy driver. */ + if (NULL == d->driver) { + int err; + down_write(&d->bus->subsys.rwsem); + d->driver = &genphy_driver.driver; + + err = d->driver->probe(d); + + if (err < 0) + return ERR_PTR(err); + + device_bind_driver(d); + up_write(&d->bus->subsys.rwsem); + } + + if (phydev->attached_dev) { + printk(KERN_ERR "%s: %s already attached\n", + dev->name, phy_id); + return ERR_PTR(-EBUSY); + } + + phydev->attached_dev = dev; + + phydev->dev_flags = flags; + + return phydev; +} +EXPORT_SYMBOL(phy_attach); + +void phy_detach(struct phy_device *phydev) +{ + phydev->attached_dev = NULL; + + /* If the device had no specific driver before (i.e. - it + * was using the generic driver), we unbind the device + * from the generic driver so that there's a chance a + * real driver could be loaded */ + if (phydev->dev.driver == &genphy_driver.driver) { + down_write(&phydev->dev.bus->subsys.rwsem); + device_release_driver(&phydev->dev); + up_write(&phydev->dev.bus->subsys.rwsem); + } +} +EXPORT_SYMBOL(phy_detach); + + +/* Generic PHY support and helper functions */ + +/* genphy_config_advert + * + * description: Writes MII_ADVERTISE with the appropriate values, + * after sanitizing the values to make sure we only advertise + * what is supported + */ +int genphy_config_advert(struct phy_device *phydev) +{ + u32 advertise; + int adv; + int err; + + /* Only allow advertising what + * this PHY supports */ + phydev->advertising &= phydev->supported; + advertise = phydev->advertising; + + /* Setup standard advertisement */ + adv = phy_read(phydev, MII_ADVERTISE); + + if (adv < 0) + return adv; + + adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP | + ADVERTISE_PAUSE_ASYM); + if (advertise & ADVERTISED_10baseT_Half) + adv |= ADVERTISE_10HALF; + if (advertise & ADVERTISED_10baseT_Full) + adv |= ADVERTISE_10FULL; + if (advertise & ADVERTISED_100baseT_Half) + adv |= ADVERTISE_100HALF; + if (advertise & ADVERTISED_100baseT_Full) + adv |= ADVERTISE_100FULL; + if (advertise & ADVERTISED_Pause) + adv |= ADVERTISE_PAUSE_CAP; + if (advertise & ADVERTISED_Asym_Pause) + adv |= ADVERTISE_PAUSE_ASYM; + + err = phy_write(phydev, MII_ADVERTISE, adv); + + if (err < 0) + return err; + + /* Configure gigabit if it's supported */ + if (phydev->supported & (SUPPORTED_1000baseT_Half | + SUPPORTED_1000baseT_Full)) { + adv = phy_read(phydev, MII_CTRL1000); + + if (adv < 0) + return adv; + + adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF); + if (advertise & SUPPORTED_1000baseT_Half) + adv |= ADVERTISE_1000HALF; + if (advertise & SUPPORTED_1000baseT_Full) + adv |= ADVERTISE_1000FULL; + err = phy_write(phydev, MII_CTRL1000, adv); + + if (err < 0) + return err; + } + + return adv; +} +EXPORT_SYMBOL(genphy_config_advert); + +/* genphy_setup_forced + * + * description: Configures MII_BMCR to force speed/duplex + * to the values in phydev. Assumes that the values are valid. + * Please see phy_sanitize_settings() */ +int genphy_setup_forced(struct phy_device *phydev) +{ + int ctl = BMCR_RESET; + + phydev->pause = phydev->asym_pause = 0; + + if (SPEED_1000 == phydev->speed) + ctl |= BMCR_SPEED1000; + else if (SPEED_100 == phydev->speed) + ctl |= BMCR_SPEED100; + + if (DUPLEX_FULL == phydev->duplex) + ctl |= BMCR_FULLDPLX; + + ctl = phy_write(phydev, MII_BMCR, ctl); + + if (ctl < 0) + return ctl; + + /* We just reset the device, so we'd better configure any + * settings the PHY requires to operate */ + if (phydev->drv->config_init) + ctl = phydev->drv->config_init(phydev); + + return ctl; +} + + +/* Enable and Restart Autonegotiation */ +int genphy_restart_aneg(struct phy_device *phydev) +{ + int ctl; + + ctl = phy_read(phydev, MII_BMCR); + + if (ctl < 0) + return ctl; + + ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); + + /* Don't isolate the PHY if we're negotiating */ + ctl &= ~(BMCR_ISOLATE); + + ctl = phy_write(phydev, MII_BMCR, ctl); + + return ctl; +} + + +/* genphy_config_aneg + * + * description: If auto-negotiation is enabled, we configure the + * advertising, and then restart auto-negotiation. If it is not + * enabled, then we write the BMCR + */ +int genphy_config_aneg(struct phy_device *phydev) +{ + int err = 0; + + if (AUTONEG_ENABLE == phydev->autoneg) { + err = genphy_config_advert(phydev); + + if (err < 0) + return err; + + err = genphy_restart_aneg(phydev); + } else + err = genphy_setup_forced(phydev); + + return err; +} +EXPORT_SYMBOL(genphy_config_aneg); + +/* genphy_update_link + * + * description: Update the value in phydev->link to reflect the + * current link value. In order to do this, we need to read + * the status register twice, keeping the second value + */ +int genphy_update_link(struct phy_device *phydev) +{ + int status; + + /* Do a fake read */ + status = phy_read(phydev, MII_BMSR); + + if (status < 0) + return status; + + /* Read link and autonegotiation status */ + status = phy_read(phydev, MII_BMSR); + + if (status < 0) + return status; + + if ((status & BMSR_LSTATUS) == 0) + phydev->link = 0; + else + phydev->link = 1; + + return 0; +} + +/* genphy_read_status + * + * description: Check the link, then figure out the current state + * by comparing what we advertise with what the link partner + * advertises. Start by checking the gigabit possibilities, + * then move on to 10/100. + */ +int genphy_read_status(struct phy_device *phydev) +{ + int adv; + int err; + int lpa; + int lpagb = 0; + + /* Update the link, but return if there + * was an error */ + err = genphy_update_link(phydev); + if (err) + return err; + + if (AUTONEG_ENABLE == phydev->autoneg) { + if (phydev->supported & (SUPPORTED_1000baseT_Half + | SUPPORTED_1000baseT_Full)) { + lpagb = phy_read(phydev, MII_STAT1000); + + if (lpagb < 0) + return lpagb; + + adv = phy_read(phydev, MII_CTRL1000); + + if (adv < 0) + return adv; + + lpagb &= adv << 2; + } + + lpa = phy_read(phydev, MII_LPA); + + if (lpa < 0) + return lpa; + + adv = phy_read(phydev, MII_ADVERTISE); + + if (adv < 0) + return adv; + + lpa &= adv; + + phydev->speed = SPEED_10; + phydev->duplex = DUPLEX_HALF; + phydev->pause = phydev->asym_pause = 0; + + if (lpagb & (LPA_1000FULL | LPA_1000HALF)) { + phydev->speed = SPEED_1000; + + if (lpagb & LPA_1000FULL) + phydev->duplex = DUPLEX_FULL; + } else if (lpa & (LPA_100FULL | LPA_100HALF)) { + phydev->speed = SPEED_100; + + if (lpa & LPA_100FULL) + phydev->duplex = DUPLEX_FULL; + } else + if (lpa & LPA_10FULL) + phydev->duplex = DUPLEX_FULL; + + if (phydev->duplex == DUPLEX_FULL){ + phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0; + phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0; + } + } else { + int bmcr = phy_read(phydev, MII_BMCR); + if (bmcr < 0) + return bmcr; + + if (bmcr & BMCR_FULLDPLX) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + + if (bmcr & BMCR_SPEED1000) + phydev->speed = SPEED_1000; + else if (bmcr & BMCR_SPEED100) + phydev->speed = SPEED_100; + else + phydev->speed = SPEED_10; + + phydev->pause = phydev->asym_pause = 0; + } + + return 0; +} +EXPORT_SYMBOL(genphy_read_status); + +static int genphy_config_init(struct phy_device *phydev) +{ + u32 val; + u32 features; + + /* For now, I'll claim that the generic driver supports + * all possible port types */ + features = (SUPPORTED_TP | SUPPORTED_MII + | SUPPORTED_AUI | SUPPORTED_FIBRE | + SUPPORTED_BNC); + + /* Do we support autonegotiation? */ + val = phy_read(phydev, MII_BMSR); + + if (val < 0) + return val; + + if (val & BMSR_ANEGCAPABLE) + features |= SUPPORTED_Autoneg; + + if (val & BMSR_100FULL) + features |= SUPPORTED_100baseT_Full; + if (val & BMSR_100HALF) + features |= SUPPORTED_100baseT_Half; + if (val & BMSR_10FULL) + features |= SUPPORTED_10baseT_Full; + if (val & BMSR_10HALF) + features |= SUPPORTED_10baseT_Half; + + if (val & BMSR_ESTATEN) { + val = phy_read(phydev, MII_ESTATUS); + + if (val < 0) + return val; + + if (val & ESTATUS_1000_TFULL) + features |= SUPPORTED_1000baseT_Full; + if (val & ESTATUS_1000_THALF) + features |= SUPPORTED_1000baseT_Half; + } + + phydev->supported = features; + phydev->advertising = features; + + return 0; +} + + +/* phy_probe + * + * description: Take care of setting up the phy_device structure, + * set the state to READY (the driver's init function should + * set it to STARTING if needed). + */ +static int phy_probe(struct device *dev) +{ + struct phy_device *phydev; + struct phy_driver *phydrv; + struct device_driver *drv; + int err = 0; + + phydev = to_phy_device(dev); + + /* Make sure the driver is held. + * XXX -- Is this correct? */ + drv = get_driver(phydev->dev.driver); + phydrv = to_phy_driver(drv); + phydev->drv = phydrv; + + /* Disable the interrupt if the PHY doesn't support it */ + if (!(phydrv->flags & PHY_HAS_INTERRUPT)) + phydev->irq = PHY_POLL; + + spin_lock(&phydev->lock); + + /* Start out supporting everything. Eventually, + * a controller will attach, and may modify one + * or both of these values */ + phydev->supported = phydrv->features; + phydev->advertising = phydrv->features; + + /* Set the state to READY by default */ + phydev->state = PHY_READY; + + if (phydev->drv->probe) + err = phydev->drv->probe(phydev); + + spin_unlock(&phydev->lock); + + if (err < 0) + return err; + + if (phydev->drv->config_init) + err = phydev->drv->config_init(phydev); + + return err; +} + +static int phy_remove(struct device *dev) +{ + struct phy_device *phydev; + + phydev = to_phy_device(dev); + + spin_lock(&phydev->lock); + phydev->state = PHY_DOWN; + spin_unlock(&phydev->lock); + + if (phydev->drv->remove) + phydev->drv->remove(phydev); + + put_driver(dev->driver); + phydev->drv = NULL; + + return 0; +} + +int phy_driver_register(struct phy_driver *new_driver) +{ + int retval; + + memset(&new_driver->driver, 0, sizeof(new_driver->driver)); + new_driver->driver.name = new_driver->name; + new_driver->driver.bus = &mdio_bus_type; + new_driver->driver.probe = phy_probe; + new_driver->driver.remove = phy_remove; + + retval = driver_register(&new_driver->driver); + + if (retval) { + printk(KERN_ERR "%s: Error %d in registering driver\n", + new_driver->name, retval); + + return retval; + } + + pr_info("%s: Registered new driver\n", new_driver->name); + + return 0; +} +EXPORT_SYMBOL(phy_driver_register); + +void phy_driver_unregister(struct phy_driver *drv) +{ + driver_unregister(&drv->driver); +} +EXPORT_SYMBOL(phy_driver_unregister); + +static struct phy_driver genphy_driver = { + .phy_id = 0xffffffff, + .phy_id_mask = 0xffffffff, + .name = "Generic PHY", + .config_init = genphy_config_init, + .features = 0, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .driver = {.owner = THIS_MODULE, }, +}; + +static int __init genphy_init(void) +{ + return phy_driver_register(&genphy_driver); + +} + +static void __exit genphy_exit(void) +{ + phy_driver_unregister(&genphy_driver); +} + +module_init(genphy_init); +module_exit(genphy_exit); diff --git a/drivers/net/phy/qsemi.c b/drivers/net/phy/qsemi.c new file mode 100644 index 0000000..d461ba4 --- /dev/null +++ b/drivers/net/phy/qsemi.c @@ -0,0 +1,143 @@ +/* + * drivers/net/phy/qsemi.c + * + * Driver for Quality Semiconductor PHYs + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +/* ------------------------------------------------------------------------- */ +/* The Quality Semiconductor QS6612 is used on the RPX CLLF */ + +/* register definitions */ + +#define MII_QS6612_MCR 17 /* Mode Control Register */ +#define MII_QS6612_FTR 27 /* Factory Test Register */ +#define MII_QS6612_MCO 28 /* Misc. Control Register */ +#define MII_QS6612_ISR 29 /* Interrupt Source Register */ +#define MII_QS6612_IMR 30 /* Interrupt Mask Register */ +#define MII_QS6612_IMR_INIT 0x003a +#define MII_QS6612_PCR 31 /* 100BaseTx PHY Control Reg. */ + +#define QS6612_PCR_AN_COMPLETE 0x1000 +#define QS6612_PCR_RLBEN 0x0200 +#define QS6612_PCR_DCREN 0x0100 +#define QS6612_PCR_4B5BEN 0x0040 +#define QS6612_PCR_TX_ISOLATE 0x0020 +#define QS6612_PCR_MLT3_DIS 0x0002 +#define QS6612_PCR_SCRM_DESCRM 0x0001 + +MODULE_DESCRIPTION("Quality Semiconductor PHY driver"); +MODULE_AUTHOR("Andy Fleming"); +MODULE_LICENSE("GPL"); + +/* Returns 0, unless there's a write error */ +static int qs6612_config_init(struct phy_device *phydev) +{ + /* The PHY powers up isolated on the RPX, + * so send a command to allow operation. + * XXX - My docs indicate this should be 0x0940 + * ...or something. The current value sets three + * reserved bits, bit 11, which specifies it should be + * set to one, bit 10, which specifies it should be set + * to 0, and bit 7, which doesn't specify. However, my + * docs are preliminary, and I will leave it like this + * until someone more knowledgable corrects me or it. + * -- Andy Fleming + */ + return phy_write(phydev, MII_QS6612_PCR, 0x0dc0); +} + +static int qs6612_ack_interrupt(struct phy_device *phydev) +{ + int err; + + err = phy_read(phydev, MII_QS6612_ISR); + + if (err < 0) + return err; + + err = phy_read(phydev, MII_BMSR); + + if (err < 0) + return err; + + err = phy_read(phydev, MII_EXPANSION); + + if (err < 0) + return err; + + return 0; +} + +static int qs6612_config_intr(struct phy_device *phydev) +{ + int err; + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) + err = phy_write(phydev, MII_QS6612_IMR, + MII_QS6612_IMR_INIT); + else + err = phy_write(phydev, MII_QS6612_IMR, 0); + + return err; + +} + +static struct phy_driver qs6612_driver = { + .phy_id = 0x00181440, + .name = "QS6612", + .phy_id_mask = 0xfffffff0, + .features = PHY_BASIC_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_init = qs6612_config_init, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .ack_interrupt = qs6612_ack_interrupt, + .config_intr = qs6612_config_intr, + .driver = { .owner = THIS_MODULE,}, +}; + +static int __init qs6612_init(void) +{ + return phy_driver_register(&qs6612_driver); +} + +static void __exit qs6612_exit(void) +{ + phy_driver_unregister(&qs6612_driver); +} + +module_init(qs6612_init); +module_exit(qs6612_exit); diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h index a0ab26a..d7021c3 100644 --- a/include/linux/ethtool.h +++ b/include/linux/ethtool.h @@ -408,6 +408,8 @@ struct ethtool_ops { #define SUPPORTED_FIBRE (1 << 10) #define SUPPORTED_BNC (1 << 11) #define SUPPORTED_10000baseT_Full (1 << 12) +#define SUPPORTED_Pause (1 << 13) +#define SUPPORTED_Asym_Pause (1 << 14) /* Indicates what features are advertised by the interface. */ #define ADVERTISED_10baseT_Half (1 << 0) @@ -423,6 +425,8 @@ struct ethtool_ops { #define ADVERTISED_FIBRE (1 << 10) #define ADVERTISED_BNC (1 << 11) #define ADVERTISED_10000baseT_Full (1 << 12) +#define ADVERTISED_Pause (1 << 13) +#define ADVERTISED_Asym_Pause (1 << 14) /* The following are all involved in forcing a particular link * mode for the device for setting things. When getting the diff --git a/include/linux/mii.h b/include/linux/mii.h index 374b615..9b8d047 100644 --- a/include/linux/mii.h +++ b/include/linux/mii.h @@ -22,6 +22,7 @@ #define MII_EXPANSION 0x06 /* Expansion register */ #define MII_CTRL1000 0x09 /* 1000BASE-T control */ #define MII_STAT1000 0x0a /* 1000BASE-T status */ +#define MII_ESTATUS 0x0f /* Extended Status */ #define MII_DCOUNTER 0x12 /* Disconnect counter */ #define MII_FCSCOUNTER 0x13 /* False carrier counter */ #define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ @@ -54,7 +55,10 @@ #define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ #define BMSR_RFAULT 0x0010 /* Remote fault detected */ #define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ -#define BMSR_RESV 0x07c0 /* Unused... */ +#define BMSR_RESV 0x00c0 /* Unused... */ +#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */ +#define BMSR_100FULL2 0x0200 /* Can do 100BASE-T2 HDX */ +#define BMSR_100HALF2 0x0400 /* Can do 100BASE-T2 FDX */ #define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ #define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ #define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ @@ -114,6 +118,9 @@ #define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */ #define EXPANSION_RESV 0xffe0 /* Unused... */ +#define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */ +#define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */ + /* N-way test register. */ #define NWAYTEST_RESV1 0x00ff /* Unused... */ #define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */ diff --git a/include/linux/phy.h b/include/linux/phy.h new file mode 100644 index 0000000..3404804 --- /dev/null +++ b/include/linux/phy.h @@ -0,0 +1,378 @@ +/* + * include/linux/phy.h + * + * Framework and drivers for configuring and reading different PHYs + * Based on code in sungem_phy.c and gianfar_phy.c + * + * Author: Andy Fleming + * + * Copyright (c) 2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __PHY_H +#define __PHY_H + +#include +#include + +#define PHY_BASIC_FEATURES (SUPPORTED_10baseT_Half | \ + SUPPORTED_10baseT_Full | \ + SUPPORTED_100baseT_Half | \ + SUPPORTED_100baseT_Full | \ + SUPPORTED_Autoneg | \ + SUPPORTED_TP | \ + SUPPORTED_MII) + +#define PHY_GBIT_FEATURES (PHY_BASIC_FEATURES | \ + SUPPORTED_1000baseT_Half | \ + SUPPORTED_1000baseT_Full) + +/* Set phydev->irq to PHY_POLL if interrupts are not supported, + * or not desired for this PHY. Set to PHY_IGNORE_INTERRUPT if + * the attached driver handles the interrupt + */ +#define PHY_POLL -1 +#define PHY_IGNORE_INTERRUPT -2 + +#define PHY_HAS_INTERRUPT 0x00000001 +#define PHY_HAS_MAGICANEG 0x00000002 + +#define MII_BUS_MAX 4 + + +#define PHY_INIT_TIMEOUT 100000 +#define PHY_STATE_TIME 1 +#define PHY_FORCE_TIMEOUT 10 +#define PHY_AN_TIMEOUT 10 + +#define PHY_MAX_ADDR 32 + +/* The Bus class for PHYs. Devices which provide access to + * PHYs should register using this structure */ +struct mii_bus { + const char *name; + int id; + void *priv; + int (*read)(struct mii_bus *bus, int phy_id, int regnum); + int (*write)(struct mii_bus *bus, int phy_id, int regnum, u16 val); + int (*reset)(struct mii_bus *bus); + + /* A lock to ensure that only one thing can read/write + * the MDIO bus at a time */ + spinlock_t mdio_lock; + + struct device *dev; + + /* list of all PHYs on bus */ + struct phy_device *phy_map[PHY_MAX_ADDR]; + + /* Pointer to an array of interrupts, each PHY's + * interrupt at the index matching its address */ + int *irq; +}; + +#define PHY_INTERRUPT_DISABLED 0x0 +#define PHY_INTERRUPT_ENABLED 0x80000000 + +/* PHY state machine states: + * + * DOWN: PHY device and driver are not ready for anything. probe + * should be called if and only if the PHY is in this state, + * given that the PHY device exists. + * - PHY driver probe function will, depending on the PHY, set + * the state to STARTING or READY + * + * STARTING: PHY device is coming up, and the ethernet driver is + * not ready. PHY drivers may set this in the probe function. + * If they do, they are responsible for making sure the state is + * eventually set to indicate whether the PHY is UP or READY, + * depending on the state when the PHY is done starting up. + * - PHY driver will set the state to READY + * - start will set the state to PENDING + * + * READY: PHY is ready to send and receive packets, but the + * controller is not. By default, PHYs which do not implement + * probe will be set to this state by phy_probe(). If the PHY + * driver knows the PHY is ready, and the PHY state is STARTING, + * then it sets this STATE. + * - start will set the state to UP + * + * PENDING: PHY device is coming up, but the ethernet driver is + * ready. phy_start will set this state if the PHY state is + * STARTING. + * - PHY driver will set the state to UP when the PHY is ready + * + * UP: The PHY and attached device are ready to do work. + * Interrupts should be started here. + * - timer moves to AN + * + * AN: The PHY is currently negotiating the link state. Link is + * therefore down for now. phy_timer will set this state when it + * detects the state is UP. config_aneg will set this state + * whenever called with phydev->autoneg set to AUTONEG_ENABLE. + * - If autonegotiation finishes, but there's no link, it sets + * the state to NOLINK. + * - If aneg finishes with link, it sets the state to RUNNING, + * and calls adjust_link + * - If autonegotiation did not finish after an arbitrary amount + * of time, autonegotiation should be tried again if the PHY + * supports "magic" autonegotiation (back to AN) + * - If it didn't finish, and no magic_aneg, move to FORCING. + * + * NOLINK: PHY is up, but not currently plugged in. + * - If the timer notes that the link comes back, we move to RUNNING + * - config_aneg moves to AN + * - phy_stop moves to HALTED + * + * FORCING: PHY is being configured with forced settings + * - if link is up, move to RUNNING + * - If link is down, we drop to the next highest setting, and + * retry (FORCING) after a timeout + * - phy_stop moves to HALTED + * + * RUNNING: PHY is currently up, running, and possibly sending + * and/or receiving packets + * - timer will set CHANGELINK if we're polling (this ensures the + * link state is polled every other cycle of this state machine, + * which makes it every other second) + * - irq will set CHANGELINK + * - config_aneg will set AN + * - phy_stop moves to HALTED + * + * CHANGELINK: PHY experienced a change in link state + * - timer moves to RUNNING if link + * - timer moves to NOLINK if the link is down + * - phy_stop moves to HALTED + * + * HALTED: PHY is up, but no polling or interrupts are done. Or + * PHY is in an error state. + * + * - phy_start moves to RESUMING + * + * RESUMING: PHY was halted, but now wants to run again. + * - If we are forcing, or aneg is done, timer moves to RUNNING + * - If aneg is not done, timer moves to AN + * - phy_stop moves to HALTED + */ +enum phy_state { + PHY_DOWN=0, + PHY_STARTING, + PHY_READY, + PHY_PENDING, + PHY_UP, + PHY_AN, + PHY_RUNNING, + PHY_NOLINK, + PHY_FORCING, + PHY_CHANGELINK, + PHY_HALTED, + PHY_RESUMING +}; + +/* phy_device: An instance of a PHY + * + * drv: Pointer to the driver for this PHY instance + * bus: Pointer to the bus this PHY is on + * dev: driver model device structure for this PHY + * phy_id: UID for this device found during discovery + * state: state of the PHY for management purposes + * dev_flags: Device-specific flags used by the PHY driver. + * addr: Bus address of PHY + * link_timeout: The number of timer firings to wait before the + * giving up on the current attempt at acquiring a link + * irq: IRQ number of the PHY's interrupt (-1 if none) + * phy_timer: The timer for handling the state machine + * phy_queue: A work_queue for the interrupt + * attached_dev: The attached enet driver's device instance ptr + * adjust_link: Callback for the enet controller to respond to + * changes in the link state. + * adjust_state: Callback for the enet driver to respond to + * changes in the state machine. + * + * speed, duplex, pause, supported, advertising, and + * autoneg are used like in mii_if_info + * + * interrupts currently only supports enabled or disabled, + * but could be changed in the future to support enabling + * and disabling specific interrupts + * + * Contains some infrastructure for polling and interrupt + * handling, as well as handling shifts in PHY hardware state + */ +struct phy_device { + /* Information about the PHY type */ + /* And management functions */ + struct phy_driver *drv; + + struct mii_bus *bus; + + struct device dev; + + u32 phy_id; + + enum phy_state state; + + u32 dev_flags; + + /* Bus address of the PHY (0-32) */ + int addr; + + /* forced speed & duplex (no autoneg) + * partner speed & duplex & pause (autoneg) + */ + int speed; + int duplex; + int pause; + int asym_pause; + + /* The most recently read link state */ + int link; + + /* Enabled Interrupts */ + u32 interrupts; + + /* Union of PHY and Attached devices' supported modes */ + /* See mii.h for more info */ + u32 supported; + u32 advertising; + + int autoneg; + + int link_timeout; + + /* Interrupt number for this PHY + * -1 means no interrupt */ + int irq; + + /* private data pointer */ + /* For use by PHYs to maintain extra state */ + void *priv; + + /* Interrupt and Polling infrastructure */ + struct work_struct phy_queue; + struct timer_list phy_timer; + + spinlock_t lock; + + struct net_device *attached_dev; + + void (*adjust_link)(struct net_device *dev); + + void (*adjust_state)(struct net_device *dev); +}; +#define to_phy_device(d) container_of(d, struct phy_device, dev) + +/* struct phy_driver: Driver structure for a particular PHY type + * + * phy_id: The result of reading the UID registers of this PHY + * type, and ANDing them with the phy_id_mask. This driver + * only works for PHYs with IDs which match this field + * name: The friendly name of this PHY type + * phy_id_mask: Defines the important bits of the phy_id + * features: A list of features (speed, duplex, etc) supported + * by this PHY + * flags: A bitfield defining certain other features this PHY + * supports (like interrupts) + * + * The drivers must implement config_aneg and read_status. All + * other functions are optional. Note that none of these + * functions should be called from interrupt time. The goal is + * for the bus read/write functions to be able to block when the + * bus transaction is happening, and be freed up by an interrupt + * (The MPC85xx has this ability, though it is not currently + * supported in the driver). + */ +struct phy_driver { + u32 phy_id; + char *name; + unsigned int phy_id_mask; + u32 features; + u32 flags; + + /* Called to initialize the PHY, + * including after a reset */ + int (*config_init)(struct phy_device *phydev); + + /* Called during discovery. Used to set + * up device-specific structures, if any */ + int (*probe)(struct phy_device *phydev); + + /* PHY Power Management */ + int (*suspend)(struct phy_device *phydev); + int (*resume)(struct phy_device *phydev); + + /* Configures the advertisement and resets + * autonegotiation if phydev->autoneg is on, + * forces the speed to the current settings in phydev + * if phydev->autoneg is off */ + int (*config_aneg)(struct phy_device *phydev); + + /* Determines the negotiated speed and duplex */ + int (*read_status)(struct phy_device *phydev); + + /* Clears any pending interrupts */ + int (*ack_interrupt)(struct phy_device *phydev); + + /* Enables or disables interrupts */ + int (*config_intr)(struct phy_device *phydev); + + /* Clears up any memory if needed */ + void (*remove)(struct phy_device *phydev); + + struct device_driver driver; +}; +#define to_phy_driver(d) container_of(d, struct phy_driver, driver) + +int phy_read(struct phy_device *phydev, u16 regnum); +int phy_write(struct phy_device *phydev, u16 regnum, u16 val); +struct phy_device* get_phy_device(struct mii_bus *bus, int addr); +int phy_clear_interrupt(struct phy_device *phydev); +int phy_config_interrupt(struct phy_device *phydev, u32 interrupts); +struct phy_device * phy_attach(struct net_device *dev, + const char *phy_id, u32 flags); +struct phy_device * phy_connect(struct net_device *dev, const char *phy_id, + void (*handler)(struct net_device *), u32 flags); +void phy_disconnect(struct phy_device *phydev); +void phy_detach(struct phy_device *phydev); +void phy_start(struct phy_device *phydev); +void phy_stop(struct phy_device *phydev); +int phy_start_aneg(struct phy_device *phydev); + +int mdiobus_register(struct mii_bus *bus); +void mdiobus_unregister(struct mii_bus *bus); +void phy_sanitize_settings(struct phy_device *phydev); +int phy_stop_interrupts(struct phy_device *phydev); + +static inline int phy_read_status(struct phy_device *phydev) { + return phydev->drv->read_status(phydev); +} + +int genphy_config_advert(struct phy_device *phydev); +int genphy_setup_forced(struct phy_device *phydev); +int genphy_restart_aneg(struct phy_device *phydev); +int genphy_config_aneg(struct phy_device *phydev); +int genphy_update_link(struct phy_device *phydev); +int genphy_read_status(struct phy_device *phydev); +void phy_driver_unregister(struct phy_driver *drv); +int phy_driver_register(struct phy_driver *new_driver); +void phy_prepare_link(struct phy_device *phydev, + void (*adjust_link)(struct net_device *)); +void phy_start_machine(struct phy_device *phydev, + void (*handler)(struct net_device *)); +void phy_stop_machine(struct phy_device *phydev); +int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd); +int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd); +int phy_mii_ioctl(struct phy_device *phydev, + struct mii_ioctl_data *mii_data, int cmd); +int phy_start_interrupts(struct phy_device *phydev); +void phy_print_status(struct phy_device *phydev); + +extern struct bus_type mdio_bus_type; +extern struct phy_driver genphy_driver; +#endif /* __PHY_H */ -- cgit v0.10.2 From 6b38aefe924daf2e4fdd73b384f21c913f31b668 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Thu, 28 Jul 2005 15:00:15 -0400 Subject: [PATCH] bonding: ALB -- allow slave to use bond's MAC address if its own MAC address conflicts In ALB mode, allow new slave to use bond's MAC address if the new slave's MAC address is being used within the bond and no other slave is using the bond's MAC address. Signed-off-by: John W. Linville Signed-off-by: Jeff Garzik diff --git a/drivers/net/bonding/bond_alb.c b/drivers/net/bonding/bond_alb.c index 5ce606d..19e829b 100644 --- a/drivers/net/bonding/bond_alb.c +++ b/drivers/net/bonding/bond_alb.c @@ -1106,18 +1106,13 @@ static int alb_handle_addr_collision_on_attach(struct bonding *bond, struct slav } } - if (found) { - /* a slave was found that is using the mac address - * of the new slave - */ - printk(KERN_ERR DRV_NAME - ": Error: the hw address of slave %s is not " - "unique - cannot enslave it!", - slave->dev->name); - return -EINVAL; - } + if (!found) + return 0; - return 0; + /* Try setting slave mac to bond address and fall-through + to code handling that situation below... */ + alb_set_slave_mac_addr(slave, bond->dev->dev_addr, + bond->alb_info.rlb_enabled); } /* The slave's address is equal to the address of the bond. -- cgit v0.10.2 From 504ff16cecf2a788181eddc9d6e47d94ce50a9f6 Mon Sep 17 00:00:00 2001 From: Jochen Friedrich Date: Wed, 27 Jul 2005 01:14:50 -0700 Subject: [PATCH] tms380tr: move to DMA API This patch makes tms380tr use the new DMA API. Now that on Alpha, this API also supports bus master DMA for ISA (platform) devices, i changed the driver to use this new API. This also works around a bug in the firmware loader: The example provided in Documentation/firmware_class no longer works, as the firmware loader now calls get_kobj_path_length() and the kernel promptly oopses, as the home-grown device doesn't have a parent. Of course, this doesn't happen with a "real" device which has its bus (or pseudo bus in the case of platform) as parent. Converted tms380tr to use new DMA API: - proteon.c, skisa.c: use platform pseudo bus to create a struct device - Space.c: delete init hooks - abyss.c, tmspci.c: pass struct device to tms380tr.c - tms380tr.c, tms380tr.h: new DMA API, use real device fo firmware loader Signed-off-by: Jochen Friedrich Cc: Jeff Garzik Signed-off-by: Andrew Morton Signed-off-by: Jeff Garzik diff --git a/drivers/net/Space.c b/drivers/net/Space.c index 3707df6..11c44be 100644 --- a/drivers/net/Space.c +++ b/drivers/net/Space.c @@ -323,12 +323,6 @@ extern struct net_device *proteon_probe(int unit); extern struct net_device *smctr_probe(int unit); static struct devprobe2 tr_probes2[] __initdata = { -#ifdef CONFIG_SKISA - {sk_isa_probe, 0}, -#endif -#ifdef CONFIG_PROTEON - {proteon_probe, 0}, -#endif #ifdef CONFIG_SMCTR {smctr_probe, 0}, #endif diff --git a/drivers/net/tokenring/abyss.c b/drivers/net/tokenring/abyss.c index 87103c4..f1e4ef1 100644 --- a/drivers/net/tokenring/abyss.c +++ b/drivers/net/tokenring/abyss.c @@ -139,7 +139,7 @@ static int __devinit abyss_attach(struct pci_dev *pdev, const struct pci_device_ */ dev->base_addr += 0x10; - ret = tmsdev_init(dev, PCI_MAX_ADDRESS, pdev); + ret = tmsdev_init(dev, PCI_MAX_ADDRESS, &pdev->dev); if (ret) { printk("%s: unable to get memory for dev->priv.\n", dev->name); diff --git a/drivers/net/tokenring/proteon.c b/drivers/net/tokenring/proteon.c index 40ad0fd..0a95977 100644 --- a/drivers/net/tokenring/proteon.c +++ b/drivers/net/tokenring/proteon.c @@ -62,8 +62,7 @@ static int dmalist[] __initdata = { }; static char cardname[] = "Proteon 1392\0"; - -struct net_device *proteon_probe(int unit); +static u64 dma_mask = ISA_MAX_ADDRESS; static int proteon_open(struct net_device *dev); static void proteon_read_eeprom(struct net_device *dev); static unsigned short proteon_setnselout_pins(struct net_device *dev); @@ -116,7 +115,7 @@ nodev: return -ENODEV; } -static int __init setup_card(struct net_device *dev) +static int __init setup_card(struct net_device *dev, struct device *pdev) { struct net_local *tp; static int versionprinted; @@ -137,7 +136,7 @@ static int __init setup_card(struct net_device *dev) } } if (err) - goto out4; + goto out5; /* At this point we have found a valid card. */ @@ -145,14 +144,15 @@ static int __init setup_card(struct net_device *dev) printk(KERN_DEBUG "%s", version); err = -EIO; - if (tmsdev_init(dev, ISA_MAX_ADDRESS, NULL)) + pdev->dma_mask = &dma_mask; + if (tmsdev_init(dev, ISA_MAX_ADDRESS, pdev)) goto out4; dev->base_addr &= ~3; proteon_read_eeprom(dev); - printk(KERN_DEBUG "%s: Ring Station Address: ", dev->name); + printk(KERN_DEBUG "proteon.c: Ring Station Address: "); printk("%2.2x", dev->dev_addr[0]); for (j = 1; j < 6; j++) printk(":%2.2x", dev->dev_addr[j]); @@ -185,7 +185,7 @@ static int __init setup_card(struct net_device *dev) if(irqlist[j] == 0) { - printk(KERN_INFO "%s: AutoSelect no IRQ available\n", dev->name); + printk(KERN_INFO "proteon.c: AutoSelect no IRQ available\n"); goto out3; } } @@ -196,15 +196,15 @@ static int __init setup_card(struct net_device *dev) break; if (irqlist[j] == 0) { - printk(KERN_INFO "%s: Illegal IRQ %d specified\n", - dev->name, dev->irq); + printk(KERN_INFO "proteon.c: Illegal IRQ %d specified\n", + dev->irq); goto out3; } if (request_irq(dev->irq, tms380tr_interrupt, 0, cardname, dev)) { - printk(KERN_INFO "%s: Selected IRQ %d not available\n", - dev->name, dev->irq); + printk(KERN_INFO "proteon.c: Selected IRQ %d not available\n", + dev->irq); goto out3; } } @@ -220,7 +220,7 @@ static int __init setup_card(struct net_device *dev) if(dmalist[j] == 0) { - printk(KERN_INFO "%s: AutoSelect no DMA available\n", dev->name); + printk(KERN_INFO "proteon.c: AutoSelect no DMA available\n"); goto out2; } } @@ -231,25 +231,25 @@ static int __init setup_card(struct net_device *dev) break; if (dmalist[j] == 0) { - printk(KERN_INFO "%s: Illegal DMA %d specified\n", - dev->name, dev->dma); + printk(KERN_INFO "proteon.c: Illegal DMA %d specified\n", + dev->dma); goto out2; } if (request_dma(dev->dma, cardname)) { - printk(KERN_INFO "%s: Selected DMA %d not available\n", - dev->name, dev->dma); + printk(KERN_INFO "proteon.c: Selected DMA %d not available\n", + dev->dma); goto out2; } } - printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n", - dev->name, dev->base_addr, dev->irq, dev->dma); - err = register_netdev(dev); if (err) goto out; + printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n", + dev->name, dev->base_addr, dev->irq, dev->dma); + return 0; out: free_dma(dev->dma); @@ -258,34 +258,11 @@ out2: out3: tmsdev_term(dev); out4: - release_region(dev->base_addr, PROTEON_IO_EXTENT); + release_region(dev->base_addr, PROTEON_IO_EXTENT); +out5: return err; } -struct net_device * __init proteon_probe(int unit) -{ - struct net_device *dev = alloc_trdev(sizeof(struct net_local)); - int err = 0; - - if (!dev) - return ERR_PTR(-ENOMEM); - - if (unit >= 0) { - sprintf(dev->name, "tr%d", unit); - netdev_boot_setup_check(dev); - } - - err = setup_card(dev); - if (err) - goto out; - - return dev; - -out: - free_netdev(dev); - return ERR_PTR(err); -} - /* * Reads MAC address from adapter RAM, which should've read it from * the onboard ROM. @@ -352,8 +329,6 @@ static int proteon_open(struct net_device *dev) return tms380tr_open(dev); } -#ifdef MODULE - #define ISATR_MAX_ADAPTERS 3 static int io[ISATR_MAX_ADAPTERS]; @@ -366,13 +341,23 @@ module_param_array(io, int, NULL, 0); module_param_array(irq, int, NULL, 0); module_param_array(dma, int, NULL, 0); -static struct net_device *proteon_dev[ISATR_MAX_ADAPTERS]; +static struct platform_device *proteon_dev[ISATR_MAX_ADAPTERS]; + +static struct device_driver proteon_driver = { + .name = "proteon", + .bus = &platform_bus_type, +}; -int init_module(void) +static int __init proteon_init(void) { struct net_device *dev; + struct platform_device *pdev; int i, num = 0, err = 0; + err = driver_register(&proteon_driver); + if (err) + return err; + for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) { dev = alloc_trdev(sizeof(struct net_local)); if (!dev) @@ -381,11 +366,15 @@ int init_module(void) dev->base_addr = io[i]; dev->irq = irq[i]; dev->dma = dma[i]; - err = setup_card(dev); + pdev = platform_device_register_simple("proteon", + i, NULL, 0); + err = setup_card(dev, &pdev->dev); if (!err) { - proteon_dev[i] = dev; + proteon_dev[i] = pdev; + dev_set_drvdata(&pdev->dev, dev); ++num; } else { + platform_device_unregister(pdev); free_netdev(dev); } } @@ -399,23 +388,28 @@ int init_module(void) return (0); } -void cleanup_module(void) +static void __exit proteon_cleanup(void) { + struct net_device *dev; int i; for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) { - struct net_device *dev = proteon_dev[i]; + struct platform_device *pdev = proteon_dev[i]; - if (!dev) + if (!pdev) continue; - + dev = dev_get_drvdata(&pdev->dev); unregister_netdev(dev); release_region(dev->base_addr, PROTEON_IO_EXTENT); free_irq(dev->irq, dev); free_dma(dev->dma); tmsdev_term(dev); free_netdev(dev); + dev_set_drvdata(&pdev->dev, NULL); + platform_device_unregister(pdev); } + driver_unregister(&proteon_driver); } -#endif /* MODULE */ +module_init(proteon_init); +module_exit(proteon_cleanup); diff --git a/drivers/net/tokenring/skisa.c b/drivers/net/tokenring/skisa.c index f26796e..03f0619 100644 --- a/drivers/net/tokenring/skisa.c +++ b/drivers/net/tokenring/skisa.c @@ -68,8 +68,7 @@ static int dmalist[] __initdata = { }; static char isa_cardname[] = "SK NET TR 4/16 ISA\0"; - -struct net_device *sk_isa_probe(int unit); +static u64 dma_mask = ISA_MAX_ADDRESS; static int sk_isa_open(struct net_device *dev); static void sk_isa_read_eeprom(struct net_device *dev); static unsigned short sk_isa_setnselout_pins(struct net_device *dev); @@ -133,7 +132,7 @@ static int __init sk_isa_probe1(struct net_device *dev, int ioaddr) return 0; } -static int __init setup_card(struct net_device *dev) +static int __init setup_card(struct net_device *dev, struct device *pdev) { struct net_local *tp; static int versionprinted; @@ -154,7 +153,7 @@ static int __init setup_card(struct net_device *dev) } } if (err) - goto out4; + goto out5; /* At this point we have found a valid card. */ @@ -162,14 +161,15 @@ static int __init setup_card(struct net_device *dev) printk(KERN_DEBUG "%s", version); err = -EIO; - if (tmsdev_init(dev, ISA_MAX_ADDRESS, NULL)) + pdev->dma_mask = &dma_mask; + if (tmsdev_init(dev, ISA_MAX_ADDRESS, pdev)) goto out4; dev->base_addr &= ~3; sk_isa_read_eeprom(dev); - printk(KERN_DEBUG "%s: Ring Station Address: ", dev->name); + printk(KERN_DEBUG "skisa.c: Ring Station Address: "); printk("%2.2x", dev->dev_addr[0]); for (j = 1; j < 6; j++) printk(":%2.2x", dev->dev_addr[j]); @@ -202,7 +202,7 @@ static int __init setup_card(struct net_device *dev) if(irqlist[j] == 0) { - printk(KERN_INFO "%s: AutoSelect no IRQ available\n", dev->name); + printk(KERN_INFO "skisa.c: AutoSelect no IRQ available\n"); goto out3; } } @@ -213,15 +213,15 @@ static int __init setup_card(struct net_device *dev) break; if (irqlist[j] == 0) { - printk(KERN_INFO "%s: Illegal IRQ %d specified\n", - dev->name, dev->irq); + printk(KERN_INFO "skisa.c: Illegal IRQ %d specified\n", + dev->irq); goto out3; } if (request_irq(dev->irq, tms380tr_interrupt, 0, isa_cardname, dev)) { - printk(KERN_INFO "%s: Selected IRQ %d not available\n", - dev->name, dev->irq); + printk(KERN_INFO "skisa.c: Selected IRQ %d not available\n", + dev->irq); goto out3; } } @@ -237,7 +237,7 @@ static int __init setup_card(struct net_device *dev) if(dmalist[j] == 0) { - printk(KERN_INFO "%s: AutoSelect no DMA available\n", dev->name); + printk(KERN_INFO "skisa.c: AutoSelect no DMA available\n"); goto out2; } } @@ -248,25 +248,25 @@ static int __init setup_card(struct net_device *dev) break; if (dmalist[j] == 0) { - printk(KERN_INFO "%s: Illegal DMA %d specified\n", - dev->name, dev->dma); + printk(KERN_INFO "skisa.c: Illegal DMA %d specified\n", + dev->dma); goto out2; } if (request_dma(dev->dma, isa_cardname)) { - printk(KERN_INFO "%s: Selected DMA %d not available\n", - dev->name, dev->dma); + printk(KERN_INFO "skisa.c: Selected DMA %d not available\n", + dev->dma); goto out2; } } - printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n", - dev->name, dev->base_addr, dev->irq, dev->dma); - err = register_netdev(dev); if (err) goto out; + printk(KERN_DEBUG "%s: IO: %#4lx IRQ: %d DMA: %d\n", + dev->name, dev->base_addr, dev->irq, dev->dma); + return 0; out: free_dma(dev->dma); @@ -275,33 +275,11 @@ out2: out3: tmsdev_term(dev); out4: - release_region(dev->base_addr, SK_ISA_IO_EXTENT); + release_region(dev->base_addr, SK_ISA_IO_EXTENT); +out5: return err; } -struct net_device * __init sk_isa_probe(int unit) -{ - struct net_device *dev = alloc_trdev(sizeof(struct net_local)); - int err = 0; - - if (!dev) - return ERR_PTR(-ENOMEM); - - if (unit >= 0) { - sprintf(dev->name, "tr%d", unit); - netdev_boot_setup_check(dev); - } - - err = setup_card(dev); - if (err) - goto out; - - return dev; -out: - free_netdev(dev); - return ERR_PTR(err); -} - /* * Reads MAC address from adapter RAM, which should've read it from * the onboard ROM. @@ -361,8 +339,6 @@ static int sk_isa_open(struct net_device *dev) return tms380tr_open(dev); } -#ifdef MODULE - #define ISATR_MAX_ADAPTERS 3 static int io[ISATR_MAX_ADAPTERS]; @@ -375,13 +351,23 @@ module_param_array(io, int, NULL, 0); module_param_array(irq, int, NULL, 0); module_param_array(dma, int, NULL, 0); -static struct net_device *sk_isa_dev[ISATR_MAX_ADAPTERS]; +static struct platform_device *sk_isa_dev[ISATR_MAX_ADAPTERS]; -int init_module(void) +static struct device_driver sk_isa_driver = { + .name = "skisa", + .bus = &platform_bus_type, +}; + +static int __init sk_isa_init(void) { struct net_device *dev; + struct platform_device *pdev; int i, num = 0, err = 0; + err = driver_register(&sk_isa_driver); + if (err) + return err; + for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) { dev = alloc_trdev(sizeof(struct net_local)); if (!dev) @@ -390,12 +376,15 @@ int init_module(void) dev->base_addr = io[i]; dev->irq = irq[i]; dev->dma = dma[i]; - err = setup_card(dev); - + pdev = platform_device_register_simple("skisa", + i, NULL, 0); + err = setup_card(dev, &pdev->dev); if (!err) { - sk_isa_dev[i] = dev; + sk_isa_dev[i] = pdev; + dev_set_drvdata(&sk_isa_dev[i]->dev, dev); ++num; } else { + platform_device_unregister(pdev); free_netdev(dev); } } @@ -409,23 +398,28 @@ int init_module(void) return (0); } -void cleanup_module(void) +static void __exit sk_isa_cleanup(void) { + struct net_device *dev; int i; for (i = 0; i < ISATR_MAX_ADAPTERS ; i++) { - struct net_device *dev = sk_isa_dev[i]; + struct platform_device *pdev = sk_isa_dev[i]; - if (!dev) + if (!pdev) continue; - + dev = dev_get_drvdata(&pdev->dev); unregister_netdev(dev); release_region(dev->base_addr, SK_ISA_IO_EXTENT); free_irq(dev->irq, dev); free_dma(dev->dma); tmsdev_term(dev); free_netdev(dev); + dev_set_drvdata(&pdev->dev, NULL); + platform_device_unregister(pdev); } + driver_unregister(&sk_isa_driver); } -#endif /* MODULE */ +module_init(sk_isa_init); +module_exit(sk_isa_cleanup); diff --git a/drivers/net/tokenring/tms380tr.c b/drivers/net/tokenring/tms380tr.c index 5e0b0ce..9a543fe 100644 --- a/drivers/net/tokenring/tms380tr.c +++ b/drivers/net/tokenring/tms380tr.c @@ -62,6 +62,7 @@ * normal operation. * 30-Dec-02 JF Removed incorrect __init from * tms380tr_init_card. + * 22-Jul-05 JF Converted to dma-mapping. * * To do: * 1. Multi/Broadcast packet handling (this may have fixed itself) @@ -89,7 +90,7 @@ static const char version[] = "tms380tr.c: v1.10 30/12/2002 by Christoph Goos, A #include #include #include -#include +#include #include #include #include @@ -114,8 +115,6 @@ static const char version[] = "tms380tr.c: v1.10 30/12/2002 by Christoph Goos, A #endif static unsigned int tms380tr_debug = TMS380TR_DEBUG; -static struct device tms_device; - /* Index to functions, as function prototypes. * Alphabetical by function name. */ @@ -434,7 +433,7 @@ static void tms380tr_init_net_local(struct net_device *dev) skb_put(tp->Rpl[i].Skb, tp->MaxPacketSize); /* data unreachable for DMA ? then use local buffer */ - dmabuf = pci_map_single(tp->pdev, tp->Rpl[i].Skb->data, tp->MaxPacketSize, PCI_DMA_FROMDEVICE); + dmabuf = dma_map_single(tp->pdev, tp->Rpl[i].Skb->data, tp->MaxPacketSize, DMA_FROM_DEVICE); if(tp->dmalimit && (dmabuf + tp->MaxPacketSize > tp->dmalimit)) { tp->Rpl[i].SkbStat = SKB_DATA_COPY; @@ -638,10 +637,10 @@ static int tms380tr_hardware_send_packet(struct sk_buff *skb, struct net_device /* Is buffer reachable for Busmaster-DMA? */ length = skb->len; - dmabuf = pci_map_single(tp->pdev, skb->data, length, PCI_DMA_TODEVICE); + dmabuf = dma_map_single(tp->pdev, skb->data, length, DMA_TO_DEVICE); if(tp->dmalimit && (dmabuf + length > tp->dmalimit)) { /* Copy frame to local buffer */ - pci_unmap_single(tp->pdev, dmabuf, length, PCI_DMA_TODEVICE); + dma_unmap_single(tp->pdev, dmabuf, length, DMA_TO_DEVICE); dmabuf = 0; i = tp->TplFree->TPLIndex; buf = tp->LocalTxBuffers[i]; @@ -1284,9 +1283,7 @@ static int tms380tr_reset_adapter(struct net_device *dev) unsigned short count, c, count2; const struct firmware *fw_entry = NULL; - strncpy(tms_device.bus_id,dev->name, BUS_ID_SIZE); - - if (request_firmware(&fw_entry, "tms380tr.bin", &tms_device) != 0) { + if (request_firmware(&fw_entry, "tms380tr.bin", tp->pdev) != 0) { printk(KERN_ALERT "%s: firmware %s is missing, cannot start.\n", dev->name, "tms380tr.bin"); return (-1); @@ -2021,7 +2018,7 @@ static void tms380tr_cancel_tx_queue(struct net_local* tp) printk(KERN_INFO "Cancel tx (%08lXh).\n", (unsigned long)tpl); if (tpl->DMABuff) - pci_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, PCI_DMA_TODEVICE); + dma_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, DMA_TO_DEVICE); dev_kfree_skb_any(tpl->Skb); } @@ -2090,7 +2087,7 @@ static void tms380tr_tx_status_irq(struct net_device *dev) tp->MacStat.tx_packets++; if (tpl->DMABuff) - pci_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, PCI_DMA_TODEVICE); + dma_unmap_single(tp->pdev, tpl->DMABuff, tpl->Skb->len, DMA_TO_DEVICE); dev_kfree_skb_irq(tpl->Skb); tpl->BusyFlag = 0; /* "free" TPL */ } @@ -2209,7 +2206,7 @@ static void tms380tr_rcv_status_irq(struct net_device *dev) tp->MacStat.rx_errors++; } if (rpl->DMABuff) - pci_unmap_single(tp->pdev, rpl->DMABuff, tp->MaxPacketSize, PCI_DMA_TODEVICE); + dma_unmap_single(tp->pdev, rpl->DMABuff, tp->MaxPacketSize, DMA_TO_DEVICE); rpl->DMABuff = 0; /* Allocate new skb for rpl */ @@ -2227,7 +2224,7 @@ static void tms380tr_rcv_status_irq(struct net_device *dev) skb_put(rpl->Skb, tp->MaxPacketSize); /* Data unreachable for DMA ? then use local buffer */ - dmabuf = pci_map_single(tp->pdev, rpl->Skb->data, tp->MaxPacketSize, PCI_DMA_FROMDEVICE); + dmabuf = dma_map_single(tp->pdev, rpl->Skb->data, tp->MaxPacketSize, DMA_FROM_DEVICE); if(tp->dmalimit && (dmabuf + tp->MaxPacketSize > tp->dmalimit)) { rpl->SkbStat = SKB_DATA_COPY; @@ -2332,12 +2329,12 @@ void tmsdev_term(struct net_device *dev) struct net_local *tp; tp = netdev_priv(dev); - pci_unmap_single(tp->pdev, tp->dmabuffer, sizeof(struct net_local), - PCI_DMA_BIDIRECTIONAL); + dma_unmap_single(tp->pdev, tp->dmabuffer, sizeof(struct net_local), + DMA_BIDIRECTIONAL); } int tmsdev_init(struct net_device *dev, unsigned long dmalimit, - struct pci_dev *pdev) + struct device *pdev) { struct net_local *tms_local; @@ -2346,8 +2343,8 @@ int tmsdev_init(struct net_device *dev, unsigned long dmalimit, init_waitqueue_head(&tms_local->wait_for_tok_int); tms_local->dmalimit = dmalimit; tms_local->pdev = pdev; - tms_local->dmabuffer = pci_map_single(pdev, (void *)tms_local, - sizeof(struct net_local), PCI_DMA_BIDIRECTIONAL); + tms_local->dmabuffer = dma_map_single(pdev, (void *)tms_local, + sizeof(struct net_local), DMA_BIDIRECTIONAL); if (tms_local->dmabuffer + sizeof(struct net_local) > dmalimit) { printk(KERN_INFO "%s: Memory not accessible for DMA\n", @@ -2370,8 +2367,6 @@ int tmsdev_init(struct net_device *dev, unsigned long dmalimit, return 0; } -#ifdef MODULE - EXPORT_SYMBOL(tms380tr_open); EXPORT_SYMBOL(tms380tr_close); EXPORT_SYMBOL(tms380tr_interrupt); @@ -2379,6 +2374,8 @@ EXPORT_SYMBOL(tmsdev_init); EXPORT_SYMBOL(tmsdev_term); EXPORT_SYMBOL(tms380tr_wait); +#ifdef MODULE + static struct module *TMS380_module = NULL; int init_module(void) diff --git a/drivers/net/tokenring/tms380tr.h b/drivers/net/tokenring/tms380tr.h index f2c5ba0..077f568 100644 --- a/drivers/net/tokenring/tms380tr.h +++ b/drivers/net/tokenring/tms380tr.h @@ -18,7 +18,7 @@ int tms380tr_open(struct net_device *dev); int tms380tr_close(struct net_device *dev); irqreturn_t tms380tr_interrupt(int irq, void *dev_id, struct pt_regs *regs); int tmsdev_init(struct net_device *dev, unsigned long dmalimit, - struct pci_dev *pdev); + struct device *pdev); void tmsdev_term(struct net_device *dev); void tms380tr_wait(unsigned long time); @@ -719,7 +719,7 @@ struct s_TPL { /* Transmit Parameter List (align on even word boundaries) */ struct sk_buff *Skb; unsigned char TPLIndex; volatile unsigned char BusyFlag;/* Flag: TPL busy? */ - dma_addr_t DMABuff; /* DMA IO bus address from pci_map */ + dma_addr_t DMABuff; /* DMA IO bus address from dma_map */ }; /* ---------------------Receive Functions-------------------------------* @@ -1060,7 +1060,7 @@ struct s_RPL { /* Receive Parameter List */ struct sk_buff *Skb; SKB_STAT SkbStat; int RPLIndex; - dma_addr_t DMABuff; /* DMA IO bus address from pci_map */ + dma_addr_t DMABuff; /* DMA IO bus address from dma_map */ }; /* Information that need to be kept for each board. */ @@ -1091,7 +1091,7 @@ typedef struct net_local { RPL *RplTail; unsigned char LocalRxBuffers[RPL_NUM][DEFAULT_PACKET_SIZE]; - struct pci_dev *pdev; + struct device *pdev; int DataRate; unsigned char ScbInUse; unsigned short CMDqueue; diff --git a/drivers/net/tokenring/tmspci.c b/drivers/net/tokenring/tmspci.c index 2e18c0a..0014aef 100644 --- a/drivers/net/tokenring/tmspci.c +++ b/drivers/net/tokenring/tmspci.c @@ -100,7 +100,7 @@ static int __devinit tms_pci_attach(struct pci_dev *pdev, const struct pci_devic unsigned int pci_irq_line; unsigned long pci_ioaddr; struct card_info *cardinfo = &card_info_table[ent->driver_data]; - + if (versionprinted++ == 0) printk("%s", version); @@ -143,7 +143,7 @@ static int __devinit tms_pci_attach(struct pci_dev *pdev, const struct pci_devic printk(":%2.2x", dev->dev_addr[i]); printk("\n"); - ret = tmsdev_init(dev, PCI_MAX_ADDRESS, pdev); + ret = tmsdev_init(dev, PCI_MAX_ADDRESS, &pdev->dev); if (ret) { printk("%s: unable to get memory for dev->priv.\n", dev->name); goto err_out_irq; -- cgit v0.10.2 From 6b9b97ce70b789014515f808b1b64c8e29e300d1 Mon Sep 17 00:00:00 2001 From: Peter Hagervall Date: Wed, 27 Jul 2005 01:14:46 -0700 Subject: [PATCH] orinoco: Sparse fixes A few sparse cleanups for orinoco.c Signed-off-by: Peter Hagervall Cc: Jeff Garzik Signed-off-by: Andrew Morton Signed-off-by: Jeff Garzik diff --git a/drivers/net/wireless/orinoco.c b/drivers/net/wireless/orinoco.c index aabcdc2..9c2d07c 100644 --- a/drivers/net/wireless/orinoco.c +++ b/drivers/net/wireless/orinoco.c @@ -4322,36 +4322,36 @@ static const struct iw_priv_args orinoco_privtab[] = { */ static const iw_handler orinoco_handler[] = { - [SIOCSIWCOMMIT-SIOCIWFIRST] (iw_handler) orinoco_ioctl_commit, - [SIOCGIWNAME -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getname, - [SIOCSIWFREQ -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setfreq, - [SIOCGIWFREQ -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getfreq, - [SIOCSIWMODE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setmode, - [SIOCGIWMODE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getmode, - [SIOCSIWSENS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setsens, - [SIOCGIWSENS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getsens, - [SIOCGIWRANGE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getiwrange, - [SIOCSIWSPY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setspy, - [SIOCGIWSPY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getspy, - [SIOCSIWAP -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setwap, - [SIOCGIWAP -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getwap, - [SIOCSIWSCAN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setscan, - [SIOCGIWSCAN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getscan, - [SIOCSIWESSID -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setessid, - [SIOCGIWESSID -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getessid, - [SIOCSIWNICKN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setnick, - [SIOCGIWNICKN -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getnick, - [SIOCSIWRATE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setrate, - [SIOCGIWRATE -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getrate, - [SIOCSIWRTS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setrts, - [SIOCGIWRTS -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getrts, - [SIOCSIWFRAG -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setfrag, - [SIOCGIWFRAG -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getfrag, - [SIOCGIWRETRY -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getretry, - [SIOCSIWENCODE-SIOCIWFIRST] (iw_handler) orinoco_ioctl_setiwencode, - [SIOCGIWENCODE-SIOCIWFIRST] (iw_handler) orinoco_ioctl_getiwencode, - [SIOCSIWPOWER -SIOCIWFIRST] (iw_handler) orinoco_ioctl_setpower, - [SIOCGIWPOWER -SIOCIWFIRST] (iw_handler) orinoco_ioctl_getpower, + [SIOCSIWCOMMIT-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_commit, + [SIOCGIWNAME -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getname, + [SIOCSIWFREQ -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setfreq, + [SIOCGIWFREQ -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getfreq, + [SIOCSIWMODE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setmode, + [SIOCGIWMODE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getmode, + [SIOCSIWSENS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setsens, + [SIOCGIWSENS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getsens, + [SIOCGIWRANGE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getiwrange, + [SIOCSIWSPY -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setspy, + [SIOCGIWSPY -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getspy, + [SIOCSIWAP -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setwap, + [SIOCGIWAP -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getwap, + [SIOCSIWSCAN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setscan, + [SIOCGIWSCAN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getscan, + [SIOCSIWESSID -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setessid, + [SIOCGIWESSID -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getessid, + [SIOCSIWNICKN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setnick, + [SIOCGIWNICKN -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getnick, + [SIOCSIWRATE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setrate, + [SIOCGIWRATE -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getrate, + [SIOCSIWRTS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setrts, + [SIOCGIWRTS -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getrts, + [SIOCSIWFRAG -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setfrag, + [SIOCGIWFRAG -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getfrag, + [SIOCGIWRETRY -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getretry, + [SIOCSIWENCODE-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setiwencode, + [SIOCGIWENCODE-SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getiwencode, + [SIOCSIWPOWER -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_setpower, + [SIOCGIWPOWER -SIOCIWFIRST] = (iw_handler) orinoco_ioctl_getpower, }; @@ -4359,15 +4359,15 @@ static const iw_handler orinoco_handler[] = { Added typecasting since we no longer use iwreq_data -- Moustafa */ static const iw_handler orinoco_private_handler[] = { - [0] (iw_handler) orinoco_ioctl_reset, - [1] (iw_handler) orinoco_ioctl_reset, - [2] (iw_handler) orinoco_ioctl_setport3, - [3] (iw_handler) orinoco_ioctl_getport3, - [4] (iw_handler) orinoco_ioctl_setpreamble, - [5] (iw_handler) orinoco_ioctl_getpreamble, - [6] (iw_handler) orinoco_ioctl_setibssport, - [7] (iw_handler) orinoco_ioctl_getibssport, - [9] (iw_handler) orinoco_ioctl_getrid, + [0] = (iw_handler) orinoco_ioctl_reset, + [1] = (iw_handler) orinoco_ioctl_reset, + [2] = (iw_handler) orinoco_ioctl_setport3, + [3] = (iw_handler) orinoco_ioctl_getport3, + [4] = (iw_handler) orinoco_ioctl_setpreamble, + [5] = (iw_handler) orinoco_ioctl_getpreamble, + [6] = (iw_handler) orinoco_ioctl_setibssport, + [7] = (iw_handler) orinoco_ioctl_getibssport, + [9] = (iw_handler) orinoco_ioctl_getrid, }; static const struct iw_handler_def orinoco_handler_def = { -- cgit v0.10.2 From cd8749b4aa6b7502e234d72cb53c00a3bc27ed1b Mon Sep 17 00:00:00 2001 From: Marcelo Feitoza Parisi Date: Fri, 15 Jul 2005 11:16:42 +0100 Subject: [PATCH] Use time_before in hamradio drivers Use of time_before() macro, defined at linux/jiffies.h, which deal with wrapping correctly and are nicer to read. Signed-off-by: Marcelo Feitoza Parisi Signed-off-by: Domen Puncer Signed-off-by: Ralf Baechle DL5RB baycom_epp.c | 3 ++- baycom_par.c | 3 ++- baycom_ser_fdx.c | 3 ++- baycom_ser_hdx.c | 3 ++- mkiss.c | 3 ++- 5 files changed, 10 insertions(+), 5 deletions(-) Signed-off-by: Jeff Garzik diff --git a/drivers/net/hamradio/baycom_epp.c b/drivers/net/hamradio/baycom_epp.c index a7f15d9..5298096 100644 --- a/drivers/net/hamradio/baycom_epp.c +++ b/drivers/net/hamradio/baycom_epp.c @@ -54,6 +54,7 @@ #include #include #include +#include #if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE) /* prototypes for ax25_encapsulate and ax25_rebuild_header */ #include @@ -287,7 +288,7 @@ static inline void baycom_int_freq(struct baycom_state *bc) * measure the interrupt frequency */ bc->debug_vals.cur_intcnt++; - if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) { + if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) { bc->debug_vals.last_jiffies = cur_jiffies; bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt; bc->debug_vals.cur_intcnt = 0; diff --git a/drivers/net/hamradio/baycom_par.c b/drivers/net/hamradio/baycom_par.c index 612ad45..3b1bef1 100644 --- a/drivers/net/hamradio/baycom_par.c +++ b/drivers/net/hamradio/baycom_par.c @@ -84,6 +84,7 @@ #include #include #include +#include #include #include @@ -165,7 +166,7 @@ static void __inline__ baycom_int_freq(struct baycom_state *bc) * measure the interrupt frequency */ bc->debug_vals.cur_intcnt++; - if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) { + if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) { bc->debug_vals.last_jiffies = cur_jiffies; bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt; bc->debug_vals.cur_intcnt = 0; diff --git a/drivers/net/hamradio/baycom_ser_fdx.c b/drivers/net/hamradio/baycom_ser_fdx.c index 25f270b..232793d 100644 --- a/drivers/net/hamradio/baycom_ser_fdx.c +++ b/drivers/net/hamradio/baycom_ser_fdx.c @@ -79,6 +79,7 @@ #include #include #include +#include /* --------------------------------------------------------------------- */ @@ -159,7 +160,7 @@ static inline void baycom_int_freq(struct baycom_state *bc) * measure the interrupt frequency */ bc->debug_vals.cur_intcnt++; - if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) { + if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) { bc->debug_vals.last_jiffies = cur_jiffies; bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt; bc->debug_vals.cur_intcnt = 0; diff --git a/drivers/net/hamradio/baycom_ser_hdx.c b/drivers/net/hamradio/baycom_ser_hdx.c index eead85d..be596a3 100644 --- a/drivers/net/hamradio/baycom_ser_hdx.c +++ b/drivers/net/hamradio/baycom_ser_hdx.c @@ -69,6 +69,7 @@ #include #include #include +#include /* --------------------------------------------------------------------- */ @@ -150,7 +151,7 @@ static inline void baycom_int_freq(struct baycom_state *bc) * measure the interrupt frequency */ bc->debug_vals.cur_intcnt++; - if ((cur_jiffies - bc->debug_vals.last_jiffies) >= HZ) { + if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) { bc->debug_vals.last_jiffies = cur_jiffies; bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt; bc->debug_vals.cur_intcnt = 0; diff --git a/drivers/net/hamradio/mkiss.c b/drivers/net/hamradio/mkiss.c index 3035422..e94952e 100644 --- a/drivers/net/hamradio/mkiss.c +++ b/drivers/net/hamradio/mkiss.c @@ -46,6 +46,7 @@ #include #include #include +#include #include @@ -429,7 +430,7 @@ static int ax_xmit(struct sk_buff *skb, struct net_device *dev) * May be we must check transmitter timeout here ? * 14 Oct 1994 Dmitry Gorodchanin. */ - if (jiffies - dev->trans_start < 20 * HZ) { + if (time_before(jiffies, dev->trans_start + 20 * HZ)) { /* 20 sec timeout not reached */ return 1; } -- cgit v0.10.2 From 2f761478a2b436efa23659b4d5c826e53b11f91a Mon Sep 17 00:00:00 2001 From: Victor Fusco Date: Fri, 1 Jul 2005 00:03:12 +0200 Subject: [PATCH] drivers/net/pci-skeleton.c: MODULE_PARM -> module_param Use module_param() instead of the old MODULE_PARM() Signed-off-by: Victor Fusco Signed-off-by: Domen Puncer Signed-off-by: Jeff Garzik diff --git a/drivers/net/pci-skeleton.c b/drivers/net/pci-skeleton.c index 4a391ea..a1ac4bd 100644 --- a/drivers/net/pci-skeleton.c +++ b/drivers/net/pci-skeleton.c @@ -486,9 +486,9 @@ struct netdrv_private { MODULE_AUTHOR ("Jeff Garzik "); MODULE_DESCRIPTION ("Skeleton for a PCI Fast Ethernet driver"); MODULE_LICENSE("GPL"); -MODULE_PARM (multicast_filter_limit, "i"); -MODULE_PARM (max_interrupt_work, "i"); -MODULE_PARM (media, "1-" __MODULE_STRING(8) "i"); +module_param(multicast_filter_limit, int, 0); +module_param(max_interrupt_work, int, 0); +module_param_array(media, int, NULL, 0); MODULE_PARM_DESC (multicast_filter_limit, "pci-skeleton maximum number of filtered multicast addresses"); MODULE_PARM_DESC (max_interrupt_work, "pci-skeleton maximum events handled per interrupt"); MODULE_PARM_DESC (media, "pci-skeleton: Bits 0-3: media type, bit 17: full duplex"); -- cgit v0.10.2 From d2ae1d2ff9282ca061b6f5244eee4c28ee2b3ffa Mon Sep 17 00:00:00 2001 From: Chuck Ebbert <76306.1226@compuserve.com> Date: Sat, 2 Jul 2005 21:28:21 -0400 Subject: [PATCH] loopback: #ifdef the TSO code This patch #ifdefs the TSO code in the loopback driver. Saves ~800 bytes of text on i386 and avoids a conditional in the fast path. Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com> Signed-off-by: Jeff Garzik diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c index b33111e..c1e3cee 100644 --- a/drivers/net/loopback.c +++ b/drivers/net/loopback.c @@ -68,6 +68,7 @@ static DEFINE_PER_CPU(struct net_device_stats, loopback_stats); * of largesending device modulo TCP checksum, which is ignored for loopback. */ +#ifdef LOOPBACK_TSO static void emulate_large_send_offload(struct sk_buff *skb) { struct iphdr *iph = skb->nh.iph; @@ -119,6 +120,7 @@ static void emulate_large_send_offload(struct sk_buff *skb) dev_kfree_skb(skb); } +#endif /* LOOPBACK_TSO */ /* * The higher levels take care of making this non-reentrant (it's @@ -136,6 +138,7 @@ static int loopback_xmit(struct sk_buff *skb, struct net_device *dev) skb->ip_summed = CHECKSUM_UNNECESSARY; #endif +#ifdef LOOPBACK_TSO if (skb_shinfo(skb)->tso_size) { BUG_ON(skb->protocol != htons(ETH_P_IP)); BUG_ON(skb->nh.iph->protocol != IPPROTO_TCP); @@ -143,7 +146,7 @@ static int loopback_xmit(struct sk_buff *skb, struct net_device *dev) emulate_large_send_offload(skb); return 0; } - +#endif dev->last_rx = jiffies; lb_stats = &per_cpu(loopback_stats, get_cpu()); @@ -209,6 +212,9 @@ struct net_device loopback_dev = { .rebuild_header = eth_rebuild_header, .flags = IFF_LOOPBACK, .features = NETIF_F_SG|NETIF_F_FRAGLIST +#ifdef LOOPBACK_TSO + |NETIF_F_TSO +#endif |NETIF_F_NO_CSUM|NETIF_F_HIGHDMA |NETIF_F_LLTX, .ethtool_ops = &loopback_ethtool_ops, -- cgit v0.10.2 From 18c16c696e8b2323a306af455c686df15c717206 Mon Sep 17 00:00:00 2001 From: Chuck Ebbert <76306.1226@compuserve.com> Date: Sat, 2 Jul 2005 21:28:22 -0400 Subject: [PATCH] loopback: optimize stats This patch slightly optimizes the loopback driver's stats update. Saves two loads, one add and one increment per packet sent. Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com> Signed-off-by: Jeff Garzik diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c index c1e3cee..dba7616 100644 --- a/drivers/net/loopback.c +++ b/drivers/net/loopback.c @@ -151,9 +151,9 @@ static int loopback_xmit(struct sk_buff *skb, struct net_device *dev) lb_stats = &per_cpu(loopback_stats, get_cpu()); lb_stats->rx_bytes += skb->len; - lb_stats->tx_bytes += skb->len; + lb_stats->tx_bytes = lb_stats->rx_bytes; lb_stats->rx_packets++; - lb_stats->tx_packets++; + lb_stats->tx_packets = lb_stats->rx_packets; put_cpu(); netif_rx(skb); -- cgit v0.10.2 From 0e920bfb0395fb16909fb98cb6e2782a1c6b73c7 Mon Sep 17 00:00:00 2001 From: Chuck Ebbert <76306.1226@compuserve.com> Date: Sat, 2 Jul 2005 21:28:23 -0400 Subject: [PATCH] loopback: whitespace cleanup Whitespace cleanup for loopback driver. Hopefully it fixes the last few annoyances. Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com> Signed-off-by: Jeff Garzik diff --git a/drivers/net/loopback.c b/drivers/net/loopback.c index dba7616..2cb6f1c 100644 --- a/drivers/net/loopback.c +++ b/drivers/net/loopback.c @@ -132,8 +132,8 @@ static int loopback_xmit(struct sk_buff *skb, struct net_device *dev) skb_orphan(skb); - skb->protocol=eth_type_trans(skb,dev); - skb->dev=dev; + skb->protocol = eth_type_trans(skb,dev); + skb->dev = dev; #ifndef LOOPBACK_MUST_CHECKSUM skb->ip_summed = CHECKSUM_UNNECESSARY; #endif @@ -211,12 +211,12 @@ struct net_device loopback_dev = { .type = ARPHRD_LOOPBACK, /* 0x0001*/ .rebuild_header = eth_rebuild_header, .flags = IFF_LOOPBACK, - .features = NETIF_F_SG|NETIF_F_FRAGLIST + .features = NETIF_F_SG | NETIF_F_FRAGLIST #ifdef LOOPBACK_TSO - |NETIF_F_TSO + | NETIF_F_TSO #endif - |NETIF_F_NO_CSUM|NETIF_F_HIGHDMA - |NETIF_F_LLTX, + | NETIF_F_NO_CSUM | NETIF_F_HIGHDMA + | NETIF_F_LLTX, .ethtool_ops = &loopback_ethtool_ops, }; -- cgit v0.10.2 From d81c0983de80c956cf37835b0d35adb3ab4bb03a Mon Sep 17 00:00:00 2001 From: Manfred Spraul Date: Sun, 31 Jul 2005 18:20:30 +0200 Subject: [PATCH] forcedeth: Jumbo Frame Support This is a multi-part message in MIME format. Signed-off-by: Jeff Garzik diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 64f0f69..91f09e5 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -85,6 +85,7 @@ * 0.33: 16 May 2005: Support for MCP51 added. * 0.34: 18 Jun 2005: Add DEV_NEED_LINKTIMER to all nForce nics. * 0.35: 26 Jun 2005: Support for MCP55 added. + * 0.36: 28 Jul 2005: Add jumbo frame support. * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -96,7 +97,7 @@ * DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few * superfluous timer interrupts from the nic. */ -#define FORCEDETH_VERSION "0.35" +#define FORCEDETH_VERSION "0.36" #define DRV_NAME "forcedeth" #include @@ -379,9 +380,13 @@ struct ring_desc { #define TX_LIMIT_START 62 /* rx/tx mac addr + type + vlan + align + slack*/ -#define RX_NIC_BUFSIZE (ETH_DATA_LEN + 64) -/* even more slack */ -#define RX_ALLOC_BUFSIZE (ETH_DATA_LEN + 128) +#define NV_RX_HEADERS (64) +/* even more slack. */ +#define NV_RX_ALLOC_PAD (64) + +/* maximum mtu size */ +#define NV_PKTLIMIT_1 ETH_DATA_LEN /* hard limit not known */ +#define NV_PKTLIMIT_2 9100 /* Actual limit according to NVidia: 9202 */ #define OOM_REFILL (1+HZ/20) #define POLL_WAIT (1+HZ/100) @@ -473,6 +478,7 @@ struct fe_priv { struct sk_buff *rx_skbuff[RX_RING]; dma_addr_t rx_dma[RX_RING]; unsigned int rx_buf_sz; + unsigned int pkt_limit; struct timer_list oom_kick; struct timer_list nic_poll; @@ -792,7 +798,7 @@ static int nv_alloc_rx(struct net_device *dev) nr = refill_rx % RX_RING; if (np->rx_skbuff[nr] == NULL) { - skb = dev_alloc_skb(RX_ALLOC_BUFSIZE); + skb = dev_alloc_skb(np->rx_buf_sz + NV_RX_ALLOC_PAD); if (!skb) break; @@ -805,7 +811,7 @@ static int nv_alloc_rx(struct net_device *dev) PCI_DMA_FROMDEVICE); np->rx_ring[nr].PacketBuffer = cpu_to_le32(np->rx_dma[nr]); wmb(); - np->rx_ring[nr].FlagLen = cpu_to_le32(RX_NIC_BUFSIZE | NV_RX_AVAIL); + np->rx_ring[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX_AVAIL); dprintk(KERN_DEBUG "%s: nv_alloc_rx: Packet %d marked as Available\n", dev->name, refill_rx); refill_rx++; @@ -831,19 +837,31 @@ static void nv_do_rx_refill(unsigned long data) enable_irq(dev->irq); } -static int nv_init_ring(struct net_device *dev) +static void nv_init_rx(struct net_device *dev) { struct fe_priv *np = get_nvpriv(dev); int i; - np->next_tx = np->nic_tx = 0; - for (i = 0; i < TX_RING; i++) - np->tx_ring[i].FlagLen = 0; - np->cur_rx = RX_RING; np->refill_rx = 0; for (i = 0; i < RX_RING; i++) np->rx_ring[i].FlagLen = 0; +} + +static void nv_init_tx(struct net_device *dev) +{ + struct fe_priv *np = get_nvpriv(dev); + int i; + + np->next_tx = np->nic_tx = 0; + for (i = 0; i < TX_RING; i++) + np->tx_ring[i].FlagLen = 0; +} + +static int nv_init_ring(struct net_device *dev) +{ + nv_init_tx(dev); + nv_init_rx(dev); return nv_alloc_rx(dev); } @@ -1207,15 +1225,82 @@ next_pkt: } } +static void set_bufsize(struct net_device *dev) +{ + struct fe_priv *np = netdev_priv(dev); + + if (dev->mtu <= ETH_DATA_LEN) + np->rx_buf_sz = ETH_DATA_LEN + NV_RX_HEADERS; + else + np->rx_buf_sz = dev->mtu + NV_RX_HEADERS; +} + /* * nv_change_mtu: dev->change_mtu function * Called with dev_base_lock held for read. */ static int nv_change_mtu(struct net_device *dev, int new_mtu) { - if (new_mtu > ETH_DATA_LEN) + struct fe_priv *np = get_nvpriv(dev); + int old_mtu; + + if (new_mtu < 64 || new_mtu > np->pkt_limit) return -EINVAL; + + old_mtu = dev->mtu; dev->mtu = new_mtu; + + /* return early if the buffer sizes will not change */ + if (old_mtu <= ETH_DATA_LEN && new_mtu <= ETH_DATA_LEN) + return 0; + if (old_mtu == new_mtu) + return 0; + + /* synchronized against open : rtnl_lock() held by caller */ + if (netif_running(dev)) { + u8 *base = get_hwbase(dev); + /* + * It seems that the nic preloads valid ring entries into an + * internal buffer. The procedure for flushing everything is + * guessed, there is probably a simpler approach. + * Changing the MTU is a rare event, it shouldn't matter. + */ + disable_irq(dev->irq); + spin_lock_bh(&dev->xmit_lock); + spin_lock(&np->lock); + /* stop engines */ + nv_stop_rx(dev); + nv_stop_tx(dev); + nv_txrx_reset(dev); + /* drain rx queue */ + nv_drain_rx(dev); + nv_drain_tx(dev); + /* reinit driver view of the rx queue */ + nv_init_rx(dev); + nv_init_tx(dev); + /* alloc new rx buffers */ + set_bufsize(dev); + if (nv_alloc_rx(dev)) { + if (!np->in_shutdown) + mod_timer(&np->oom_kick, jiffies + OOM_REFILL); + } + /* reinit nic view of the rx queue */ + writel(np->rx_buf_sz, base + NvRegOffloadConfig); + writel((u32) np->ring_addr, base + NvRegRxRingPhysAddr); + writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr); + writel( ((RX_RING-1) << NVREG_RINGSZ_RXSHIFT) + ((TX_RING-1) << NVREG_RINGSZ_TXSHIFT), + base + NvRegRingSizes); + pci_push(base); + writel(NVREG_TXRXCTL_KICK|np->desc_ver, get_hwbase(dev) + NvRegTxRxControl); + pci_push(base); + + /* restart rx engine */ + nv_start_rx(dev); + nv_start_tx(dev); + spin_unlock(&np->lock); + spin_unlock_bh(&dev->xmit_lock); + enable_irq(dev->irq); + } return 0; } @@ -1792,6 +1877,7 @@ static int nv_open(struct net_device *dev) writel(0, base + NvRegAdapterControl); /* 2) initialize descriptor rings */ + set_bufsize(dev); oom = nv_init_ring(dev); writel(0, base + NvRegLinkSpeed); @@ -1837,7 +1923,7 @@ static int nv_open(struct net_device *dev) writel(NVREG_MISC1_FORCE | NVREG_MISC1_HD, base + NvRegMisc1); writel(readl(base + NvRegTransmitterStatus), base + NvRegTransmitterStatus); writel(NVREG_PFF_ALWAYS, base + NvRegPacketFilterFlags); - writel(NVREG_OFFLOAD_NORMAL, base + NvRegOffloadConfig); + writel(np->rx_buf_sz, base + NvRegOffloadConfig); writel(readl(base + NvRegReceiverStatus), base + NvRegReceiverStatus); get_random_bytes(&i, sizeof(i)); @@ -2007,13 +2093,16 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i /* handle different descriptor versions */ if (pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_1 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_2 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_3 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_12 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_13) + pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_2 || + pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_3 || + pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_12 || + pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_13) { np->desc_ver = DESC_VER_1; - else + np->pkt_limit = NV_PKTLIMIT_1; + } else { np->desc_ver = DESC_VER_2; + np->pkt_limit = NV_PKTLIMIT_2; + } err = -ENOMEM; np->base = ioremap(addr, NV_PCI_REGSZ); -- cgit v0.10.2 From dc8216c192795b62f30ca34299fb79e897438372 Mon Sep 17 00:00:00 2001 From: Manfred Spraul Date: Sun, 31 Jul 2005 18:26:05 +0200 Subject: [PATCH] forcedeth: Improve ethtool support This is a multi-part message in MIME format. Signed-off-by: Jeff Garzik diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 91f09e5..9c49c5e 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -85,7 +85,8 @@ * 0.33: 16 May 2005: Support for MCP51 added. * 0.34: 18 Jun 2005: Add DEV_NEED_LINKTIMER to all nForce nics. * 0.35: 26 Jun 2005: Support for MCP55 added. - * 0.36: 28 Jul 2005: Add jumbo frame support. + * 0.36: 28 Jun 2005: Add jumbo frame support. + * 0.37: 10 Jul 2005: Additional ethtool support, cleanup of pci id list * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -97,7 +98,7 @@ * DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few * superfluous timer interrupts from the nic. */ -#define FORCEDETH_VERSION "0.36" +#define FORCEDETH_VERSION "0.37" #define DRV_NAME "forcedeth" #include @@ -137,6 +138,7 @@ #define DEV_IRQMASK_2 0x0004 /* use NVREG_IRQMASK_WANTED_2 for irq mask */ #define DEV_NEED_TIMERIRQ 0x0008 /* set the timer irq flag in the irq mask */ #define DEV_NEED_LINKTIMER 0x0010 /* poll link settings. Relies on the timer irq */ +#define DEV_HAS_LARGEDESC 0x0020 /* device supports jumbo frames and needs packet format 2 */ enum { NvRegIrqStatus = 0x000, @@ -1846,6 +1848,50 @@ static int nv_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd) return 0; } +#define FORCEDETH_REGS_VER 1 +#define FORCEDETH_REGS_SIZE 0x400 /* 256 32-bit registers */ + +static int nv_get_regs_len(struct net_device *dev) +{ + return FORCEDETH_REGS_SIZE; +} + +static void nv_get_regs(struct net_device *dev, struct ethtool_regs *regs, void *buf) +{ + struct fe_priv *np = get_nvpriv(dev); + u8 __iomem *base = get_hwbase(dev); + u32 *rbuf = buf; + int i; + + regs->version = FORCEDETH_REGS_VER; + spin_lock_irq(&np->lock); + for (i=0;ilock); +} + +static int nv_nway_reset(struct net_device *dev) +{ + struct fe_priv *np = get_nvpriv(dev); + int ret; + + spin_lock_irq(&np->lock); + if (np->autoneg) { + int bmcr; + + bmcr = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ); + bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART); + mii_rw(dev, np->phyaddr, MII_BMCR, bmcr); + + ret = 0; + } else { + ret = -EINVAL; + } + spin_unlock_irq(&np->lock); + + return ret; +} + static struct ethtool_ops ops = { .get_drvinfo = nv_get_drvinfo, .get_link = ethtool_op_get_link, @@ -1853,6 +1899,9 @@ static struct ethtool_ops ops = { .set_wol = nv_set_wol, .get_settings = nv_get_settings, .set_settings = nv_set_settings, + .get_regs_len = nv_get_regs_len, + .get_regs = nv_get_regs, + .nway_reset = nv_nway_reset, }; static int nv_open(struct net_device *dev) @@ -2092,18 +2141,13 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i } /* handle different descriptor versions */ - if (pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_1 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_2 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_3 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_12 || - pci_dev->device == PCI_DEVICE_ID_NVIDIA_NVENET_13) { - np->desc_ver = DESC_VER_1; - np->pkt_limit = NV_PKTLIMIT_1; - } else { + np->desc_ver = DESC_VER_1; + np->pkt_limit = NV_PKTLIMIT_1; + if (id->driver_data & DEV_HAS_LARGEDESC) { np->desc_ver = DESC_VER_2; np->pkt_limit = NV_PKTLIMIT_2; } - + err = -ENOMEM; np->base = ioremap(addr, NV_PCI_REGSZ); if (!np->base) @@ -2284,109 +2328,74 @@ static void __devexit nv_remove(struct pci_dev *pci_dev) static struct pci_device_id pci_tbl[] = { { /* nForce Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_1, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_1), .driver_data = DEV_IRQMASK_1|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* nForce2 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_2, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_2), .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* nForce3 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_3, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_3), .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* nForce3 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_4, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_4), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* nForce3 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_5, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_5), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* nForce3 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_6, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_6), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* nForce3 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_7, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_7), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* CK804 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_8, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_8), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* CK804 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_9, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_9), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP04 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_10, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_10), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP04 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_11, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_11), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP51 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_12, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_12), .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* MCP51 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_13, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_13), .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* MCP55 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_14, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_14), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP55 Ethernet Controller */ - .vendor = PCI_VENDOR_ID_NVIDIA, - .device = PCI_DEVICE_ID_NVIDIA_NVENET_15, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_15), + .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| + DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, {0,}, }; -- cgit v0.10.2 From c2dba06dae7d6c4d15b83ea12d8c601cffd0aee9 Mon Sep 17 00:00:00 2001 From: Manfred Spraul Date: Sun, 31 Jul 2005 18:29:47 +0200 Subject: [PATCH] forcedeth: rewritten tx irq handling This is a multi-part message in MIME format. Signed-off-by: Jeff Garzik diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 9c49c5e..746ad01 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -87,6 +87,8 @@ * 0.35: 26 Jun 2005: Support for MCP55 added. * 0.36: 28 Jun 2005: Add jumbo frame support. * 0.37: 10 Jul 2005: Additional ethtool support, cleanup of pci id list + * 0.38: 16 Jul 2005: tx irq rewrite: Use global flags instead of + * per-packet flags. * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -98,7 +100,7 @@ * DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few * superfluous timer interrupts from the nic. */ -#define FORCEDETH_VERSION "0.37" +#define FORCEDETH_VERSION "0.38" #define DRV_NAME "forcedeth" #include @@ -133,12 +135,9 @@ * Hardware access: */ -#define DEV_NEED_LASTPACKET1 0x0001 /* set LASTPACKET1 in tx flags */ -#define DEV_IRQMASK_1 0x0002 /* use NVREG_IRQMASK_WANTED_1 for irq mask */ -#define DEV_IRQMASK_2 0x0004 /* use NVREG_IRQMASK_WANTED_2 for irq mask */ -#define DEV_NEED_TIMERIRQ 0x0008 /* set the timer irq flag in the irq mask */ -#define DEV_NEED_LINKTIMER 0x0010 /* poll link settings. Relies on the timer irq */ -#define DEV_HAS_LARGEDESC 0x0020 /* device supports jumbo frames and needs packet format 2 */ +#define DEV_NEED_TIMERIRQ 0x0001 /* set the timer irq flag in the irq mask */ +#define DEV_NEED_LINKTIMER 0x0002 /* poll link settings. Relies on the timer irq */ +#define DEV_HAS_LARGEDESC 0x0004 /* device supports jumbo frames and needs packet format 2 */ enum { NvRegIrqStatus = 0x000, @@ -149,13 +148,16 @@ enum { #define NVREG_IRQ_RX 0x0002 #define NVREG_IRQ_RX_NOBUF 0x0004 #define NVREG_IRQ_TX_ERR 0x0008 -#define NVREG_IRQ_TX2 0x0010 +#define NVREG_IRQ_TX_OK 0x0010 #define NVREG_IRQ_TIMER 0x0020 #define NVREG_IRQ_LINK 0x0040 +#define NVREG_IRQ_TX_ERROR 0x0080 #define NVREG_IRQ_TX1 0x0100 -#define NVREG_IRQMASK_WANTED_1 0x005f -#define NVREG_IRQMASK_WANTED_2 0x0147 -#define NVREG_IRQ_UNKNOWN (~(NVREG_IRQ_RX_ERROR|NVREG_IRQ_RX|NVREG_IRQ_RX_NOBUF|NVREG_IRQ_TX_ERR|NVREG_IRQ_TX2|NVREG_IRQ_TIMER|NVREG_IRQ_LINK|NVREG_IRQ_TX1)) +#define NVREG_IRQMASK_WANTED 0x00df + +#define NVREG_IRQ_UNKNOWN (~(NVREG_IRQ_RX_ERROR|NVREG_IRQ_RX|NVREG_IRQ_RX_NOBUF|NVREG_IRQ_TX_ERR| \ + NVREG_IRQ_TX_OK|NVREG_IRQ_TIMER|NVREG_IRQ_LINK|NVREG_IRQ_TX_ERROR| \ + NVREG_IRQ_TX1)) NvRegUnknownSetupReg6 = 0x008, #define NVREG_UNKSETUP6_VAL 3 @@ -296,7 +298,7 @@ struct ring_desc { #define NV_TX_LASTPACKET (1<<16) #define NV_TX_RETRYERROR (1<<19) -#define NV_TX_LASTPACKET1 (1<<24) +#define NV_TX_FORCED_INTERRUPT (1<<24) #define NV_TX_DEFERRED (1<<26) #define NV_TX_CARRIERLOST (1<<27) #define NV_TX_LATECOLLISION (1<<28) @@ -306,7 +308,7 @@ struct ring_desc { #define NV_TX2_LASTPACKET (1<<29) #define NV_TX2_RETRYERROR (1<<18) -#define NV_TX2_LASTPACKET1 (1<<23) +#define NV_TX2_FORCED_INTERRUPT (1<<30) #define NV_TX2_DEFERRED (1<<25) #define NV_TX2_CARRIERLOST (1<<26) #define NV_TX2_LATECOLLISION (1<<27) @@ -1013,9 +1015,39 @@ static void nv_tx_timeout(struct net_device *dev) struct fe_priv *np = get_nvpriv(dev); u8 __iomem *base = get_hwbase(dev); - dprintk(KERN_DEBUG "%s: Got tx_timeout. irq: %08x\n", dev->name, + printk(KERN_INFO "%s: Got tx_timeout. irq: %08x\n", dev->name, readl(base + NvRegIrqStatus) & NVREG_IRQSTAT_MASK); + { + int i; + + printk(KERN_INFO "%s: Ring at %lx: next %d nic %d\n", + dev->name, (unsigned long)np->ring_addr, + np->next_tx, np->nic_tx); + printk(KERN_INFO "%s: Dumping tx registers\n", dev->name); + for (i=0;i<0x400;i+= 32) { + printk(KERN_INFO "%3x: %08x %08x %08x %08x %08x %08x %08x %08x\n", + i, + readl(base + i + 0), readl(base + i + 4), + readl(base + i + 8), readl(base + i + 12), + readl(base + i + 16), readl(base + i + 20), + readl(base + i + 24), readl(base + i + 28)); + } + printk(KERN_INFO "%s: Dumping tx ring\n", dev->name); + for (i=0;itx_ring[i].PacketBuffer), + le32_to_cpu(np->tx_ring[i].FlagLen), + le32_to_cpu(np->tx_ring[i+1].PacketBuffer), + le32_to_cpu(np->tx_ring[i+1].FlagLen), + le32_to_cpu(np->tx_ring[i+2].PacketBuffer), + le32_to_cpu(np->tx_ring[i+2].FlagLen), + le32_to_cpu(np->tx_ring[i+3].PacketBuffer), + le32_to_cpu(np->tx_ring[i+3].FlagLen)); + } + } + spin_lock_irq(&np->lock); /* 1) stop tx engine */ @@ -1557,7 +1589,7 @@ static irqreturn_t nv_nic_irq(int foo, void *data, struct pt_regs *regs) if (!(events & np->irqmask)) break; - if (events & (NVREG_IRQ_TX1|NVREG_IRQ_TX2|NVREG_IRQ_TX_ERR)) { + if (events & (NVREG_IRQ_TX1|NVREG_IRQ_TX_OK|NVREG_IRQ_TX_ERROR|NVREG_IRQ_TX_ERR)) { spin_lock(&np->lock); nv_tx_done(dev); spin_unlock(&np->lock); @@ -2213,17 +2245,10 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i if (np->desc_ver == DESC_VER_1) { np->tx_flags = NV_TX_LASTPACKET|NV_TX_VALID; - if (id->driver_data & DEV_NEED_LASTPACKET1) - np->tx_flags |= NV_TX_LASTPACKET1; } else { np->tx_flags = NV_TX2_LASTPACKET|NV_TX2_VALID; - if (id->driver_data & DEV_NEED_LASTPACKET1) - np->tx_flags |= NV_TX2_LASTPACKET1; } - if (id->driver_data & DEV_IRQMASK_1) - np->irqmask = NVREG_IRQMASK_WANTED_1; - if (id->driver_data & DEV_IRQMASK_2) - np->irqmask = NVREG_IRQMASK_WANTED_2; + np->irqmask = NVREG_IRQMASK_WANTED; if (id->driver_data & DEV_NEED_TIMERIRQ) np->irqmask |= NVREG_IRQ_TIMER; if (id->driver_data & DEV_NEED_LINKTIMER) { @@ -2329,73 +2354,63 @@ static void __devexit nv_remove(struct pci_dev *pci_dev) static struct pci_device_id pci_tbl[] = { { /* nForce Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_1), - .driver_data = DEV_IRQMASK_1|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* nForce2 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_2), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* nForce3 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_3), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* nForce3 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_4), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* nForce3 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_5), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* nForce3 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_6), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* nForce3 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_7), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* CK804 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_8), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* CK804 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_9), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP04 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_10), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP04 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_11), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP51 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_12), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* MCP51 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_13), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, }, { /* MCP55 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_14), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, { /* MCP55 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_15), - .driver_data = DEV_NEED_LASTPACKET1|DEV_IRQMASK_2|DEV_NEED_TIMERIRQ| - DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, }, {0,}, }; -- cgit v0.10.2 From ee73362cdd7d9b8166424f5f9e3176c629ac5cb2 Mon Sep 17 00:00:00 2001 From: Manfred Spraul Date: Sun, 31 Jul 2005 18:32:26 +0200 Subject: [PATCH] forcedeth: 64-bit DMA support This is a multi-part message in MIME format. Signed-off-by: Jeff Garzik diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 746ad01..4d38acb 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -89,6 +89,7 @@ * 0.37: 10 Jul 2005: Additional ethtool support, cleanup of pci id list * 0.38: 16 Jul 2005: tx irq rewrite: Use global flags instead of * per-packet flags. + * 0.39: 18 Jul 2005: Add 64bit descriptor support. * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -100,7 +101,7 @@ * DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few * superfluous timer interrupts from the nic. */ -#define FORCEDETH_VERSION "0.38" +#define FORCEDETH_VERSION "0.39" #define DRV_NAME "forcedeth" #include @@ -138,6 +139,7 @@ #define DEV_NEED_TIMERIRQ 0x0001 /* set the timer irq flag in the irq mask */ #define DEV_NEED_LINKTIMER 0x0002 /* poll link settings. Relies on the timer irq */ #define DEV_HAS_LARGEDESC 0x0004 /* device supports jumbo frames and needs packet format 2 */ +#define DEV_HAS_HIGH_DMA 0x0008 /* device supports 64bit dma */ enum { NvRegIrqStatus = 0x000, @@ -291,6 +293,18 @@ struct ring_desc { u32 FlagLen; }; +struct ring_desc_ex { + u32 PacketBufferHigh; + u32 PacketBufferLow; + u32 Reserved; + u32 FlagLen; +}; + +typedef union _ring_type { + struct ring_desc* orig; + struct ring_desc_ex* ex; +} ring_type; + #define FLAG_MASK_V1 0xffff0000 #define FLAG_MASK_V2 0xffffc000 #define LEN_MASK_V1 (0xffffffff ^ FLAG_MASK_V1) @@ -405,6 +419,7 @@ struct ring_desc { */ #define DESC_VER_1 0x0 #define DESC_VER_2 (0x02100|NVREG_TXRXCTL_RXCHECK) +#define DESC_VER_3 (0x02200|NVREG_TXRXCTL_RXCHECK) /* PHY defines */ #define PHY_OUI_MARVELL 0x5043 @@ -477,7 +492,7 @@ struct fe_priv { /* rx specific fields. * Locking: Within irq hander or disable_irq+spin_lock(&np->lock); */ - struct ring_desc *rx_ring; + ring_type rx_ring; unsigned int cur_rx, refill_rx; struct sk_buff *rx_skbuff[RX_RING]; dma_addr_t rx_dma[RX_RING]; @@ -494,7 +509,7 @@ struct fe_priv { /* * tx specific fields. */ - struct ring_desc *tx_ring; + ring_type tx_ring; unsigned int next_tx, nic_tx; struct sk_buff *tx_skbuff[TX_RING]; dma_addr_t tx_dma[TX_RING]; @@ -529,6 +544,11 @@ static inline u32 nv_descr_getlength(struct ring_desc *prd, u32 v) & ((v == DESC_VER_1) ? LEN_MASK_V1 : LEN_MASK_V2); } +static inline u32 nv_descr_getlength_ex(struct ring_desc_ex *prd, u32 v) +{ + return le32_to_cpu(prd->FlagLen) & LEN_MASK_V2; +} + static int reg_delay(struct net_device *dev, int offset, u32 mask, u32 target, int delay, int delaymax, const char *msg) { @@ -813,9 +833,16 @@ static int nv_alloc_rx(struct net_device *dev) } np->rx_dma[nr] = pci_map_single(np->pci_dev, skb->data, skb->len, PCI_DMA_FROMDEVICE); - np->rx_ring[nr].PacketBuffer = cpu_to_le32(np->rx_dma[nr]); - wmb(); - np->rx_ring[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX_AVAIL); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) { + np->rx_ring.orig[nr].PacketBuffer = cpu_to_le32(np->rx_dma[nr]); + wmb(); + np->rx_ring.orig[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX_AVAIL); + } else { + np->rx_ring.ex[nr].PacketBufferHigh = cpu_to_le64(np->rx_dma[nr]) >> 32; + np->rx_ring.ex[nr].PacketBufferLow = cpu_to_le64(np->rx_dma[nr]) & 0x0FFFFFFFF; + wmb(); + np->rx_ring.ex[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX2_AVAIL); + } dprintk(KERN_DEBUG "%s: nv_alloc_rx: Packet %d marked as Available\n", dev->name, refill_rx); refill_rx++; @@ -849,7 +876,10 @@ static void nv_init_rx(struct net_device *dev) np->cur_rx = RX_RING; np->refill_rx = 0; for (i = 0; i < RX_RING; i++) - np->rx_ring[i].FlagLen = 0; + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + np->rx_ring.orig[i].FlagLen = 0; + else + np->rx_ring.ex[i].FlagLen = 0; } static void nv_init_tx(struct net_device *dev) @@ -859,7 +889,10 @@ static void nv_init_tx(struct net_device *dev) np->next_tx = np->nic_tx = 0; for (i = 0; i < TX_RING; i++) - np->tx_ring[i].FlagLen = 0; + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + np->tx_ring.orig[i].FlagLen = 0; + else + np->tx_ring.ex[i].FlagLen = 0; } static int nv_init_ring(struct net_device *dev) @@ -874,7 +907,10 @@ static void nv_drain_tx(struct net_device *dev) struct fe_priv *np = get_nvpriv(dev); int i; for (i = 0; i < TX_RING; i++) { - np->tx_ring[i].FlagLen = 0; + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + np->tx_ring.orig[i].FlagLen = 0; + else + np->tx_ring.ex[i].FlagLen = 0; if (np->tx_skbuff[i]) { pci_unmap_single(np->pci_dev, np->tx_dma[i], np->tx_skbuff[i]->len, @@ -891,7 +927,10 @@ static void nv_drain_rx(struct net_device *dev) struct fe_priv *np = get_nvpriv(dev); int i; for (i = 0; i < RX_RING; i++) { - np->rx_ring[i].FlagLen = 0; + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + np->rx_ring.orig[i].FlagLen = 0; + else + np->rx_ring.ex[i].FlagLen = 0; wmb(); if (np->rx_skbuff[i]) { pci_unmap_single(np->pci_dev, np->rx_dma[i], @@ -922,11 +961,19 @@ static int nv_start_xmit(struct sk_buff *skb, struct net_device *dev) np->tx_dma[nr] = pci_map_single(np->pci_dev, skb->data,skb->len, PCI_DMA_TODEVICE); - np->tx_ring[nr].PacketBuffer = cpu_to_le32(np->tx_dma[nr]); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + np->tx_ring.orig[nr].PacketBuffer = cpu_to_le32(np->tx_dma[nr]); + else { + np->tx_ring.ex[nr].PacketBufferHigh = cpu_to_le64(np->tx_dma[nr]) >> 32; + np->tx_ring.ex[nr].PacketBufferLow = cpu_to_le64(np->tx_dma[nr]) & 0x0FFFFFFFF; + } spin_lock_irq(&np->lock); wmb(); - np->tx_ring[nr].FlagLen = cpu_to_le32( (skb->len-1) | np->tx_flags ); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + np->tx_ring.orig[nr].FlagLen = cpu_to_le32( (skb->len-1) | np->tx_flags ); + else + np->tx_ring.ex[nr].FlagLen = cpu_to_le32( (skb->len-1) | np->tx_flags ); dprintk(KERN_DEBUG "%s: nv_start_xmit: packet packet %d queued for transmission.\n", dev->name, np->next_tx); { @@ -964,7 +1011,10 @@ static void nv_tx_done(struct net_device *dev) while (np->nic_tx != np->next_tx) { i = np->nic_tx % TX_RING; - Flags = le32_to_cpu(np->tx_ring[i].FlagLen); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + Flags = le32_to_cpu(np->tx_ring.orig[i].FlagLen); + else + Flags = le32_to_cpu(np->tx_ring.ex[i].FlagLen); dprintk(KERN_DEBUG "%s: nv_tx_done: looking at packet %d, Flags 0x%x.\n", dev->name, np->nic_tx, Flags); @@ -1035,16 +1085,33 @@ static void nv_tx_timeout(struct net_device *dev) } printk(KERN_INFO "%s: Dumping tx ring\n", dev->name); for (i=0;itx_ring[i].PacketBuffer), - le32_to_cpu(np->tx_ring[i].FlagLen), - le32_to_cpu(np->tx_ring[i+1].PacketBuffer), - le32_to_cpu(np->tx_ring[i+1].FlagLen), - le32_to_cpu(np->tx_ring[i+2].PacketBuffer), - le32_to_cpu(np->tx_ring[i+2].FlagLen), - le32_to_cpu(np->tx_ring[i+3].PacketBuffer), - le32_to_cpu(np->tx_ring[i+3].FlagLen)); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) { + printk(KERN_INFO "%03x: %08x %08x // %08x %08x // %08x %08x // %08x %08x\n", + i, + le32_to_cpu(np->tx_ring.orig[i].PacketBuffer), + le32_to_cpu(np->tx_ring.orig[i].FlagLen), + le32_to_cpu(np->tx_ring.orig[i+1].PacketBuffer), + le32_to_cpu(np->tx_ring.orig[i+1].FlagLen), + le32_to_cpu(np->tx_ring.orig[i+2].PacketBuffer), + le32_to_cpu(np->tx_ring.orig[i+2].FlagLen), + le32_to_cpu(np->tx_ring.orig[i+3].PacketBuffer), + le32_to_cpu(np->tx_ring.orig[i+3].FlagLen)); + } else { + printk(KERN_INFO "%03x: %08x %08x %08x // %08x %08x %08x // %08x %08x %08x // %08x %08x %08x\n", + i, + le32_to_cpu(np->tx_ring.ex[i].PacketBufferHigh), + le32_to_cpu(np->tx_ring.ex[i].PacketBufferLow), + le32_to_cpu(np->tx_ring.ex[i].FlagLen), + le32_to_cpu(np->tx_ring.ex[i+1].PacketBufferHigh), + le32_to_cpu(np->tx_ring.ex[i+1].PacketBufferLow), + le32_to_cpu(np->tx_ring.ex[i+1].FlagLen), + le32_to_cpu(np->tx_ring.ex[i+2].PacketBufferHigh), + le32_to_cpu(np->tx_ring.ex[i+2].PacketBufferLow), + le32_to_cpu(np->tx_ring.ex[i+2].FlagLen), + le32_to_cpu(np->tx_ring.ex[i+3].PacketBufferHigh), + le32_to_cpu(np->tx_ring.ex[i+3].PacketBufferLow), + le32_to_cpu(np->tx_ring.ex[i+3].FlagLen)); + } } } @@ -1061,7 +1128,10 @@ static void nv_tx_timeout(struct net_device *dev) printk(KERN_DEBUG "%s: tx_timeout: dead entries!\n", dev->name); nv_drain_tx(dev); np->next_tx = np->nic_tx = 0; - writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr); + else + writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc_ex)), base + NvRegTxRingPhysAddr); netif_wake_queue(dev); } @@ -1136,8 +1206,13 @@ static void nv_rx_process(struct net_device *dev) break; /* we scanned the whole ring - do not continue */ i = np->cur_rx % RX_RING; - Flags = le32_to_cpu(np->rx_ring[i].FlagLen); - len = nv_descr_getlength(&np->rx_ring[i], np->desc_ver); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) { + Flags = le32_to_cpu(np->rx_ring.orig[i].FlagLen); + len = nv_descr_getlength(&np->rx_ring.orig[i], np->desc_ver); + } else { + Flags = le32_to_cpu(np->rx_ring.ex[i].FlagLen); + len = nv_descr_getlength_ex(&np->rx_ring.ex[i], np->desc_ver); + } dprintk(KERN_DEBUG "%s: nv_rx_process: looking at packet %d, Flags 0x%x.\n", dev->name, np->cur_rx, Flags); @@ -1321,7 +1396,10 @@ static int nv_change_mtu(struct net_device *dev, int new_mtu) /* reinit nic view of the rx queue */ writel(np->rx_buf_sz, base + NvRegOffloadConfig); writel((u32) np->ring_addr, base + NvRegRxRingPhysAddr); - writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr); + else + writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc_ex)), base + NvRegTxRingPhysAddr); writel( ((RX_RING-1) << NVREG_RINGSZ_RXSHIFT) + ((TX_RING-1) << NVREG_RINGSZ_TXSHIFT), base + NvRegRingSizes); pci_push(base); @@ -1982,7 +2060,10 @@ static int nv_open(struct net_device *dev) /* 4) give hw rings */ writel((u32) np->ring_addr, base + NvRegRxRingPhysAddr); - writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc)), base + NvRegTxRingPhysAddr); + else + writel((u32) (np->ring_addr + RX_RING*sizeof(struct ring_desc_ex)), base + NvRegTxRingPhysAddr); writel( ((RX_RING-1) << NVREG_RINGSZ_RXSHIFT) + ((TX_RING-1) << NVREG_RINGSZ_TXSHIFT), base + NvRegRingSizes); @@ -2173,24 +2254,48 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i } /* handle different descriptor versions */ - np->desc_ver = DESC_VER_1; - np->pkt_limit = NV_PKTLIMIT_1; - if (id->driver_data & DEV_HAS_LARGEDESC) { + if (id->driver_data & DEV_HAS_HIGH_DMA) { + /* packet format 3: supports 40-bit addressing */ + np->desc_ver = DESC_VER_3; + if (pci_set_dma_mask(pci_dev, 0x0000007fffffffffULL)) { + printk(KERN_INFO "forcedeth: 64-bit DMA failed, using 32-bit addressing for device %s.\n", + pci_name(pci_dev)); + } + } else if (id->driver_data & DEV_HAS_LARGEDESC) { + /* packet format 2: supports jumbo frames */ np->desc_ver = DESC_VER_2; - np->pkt_limit = NV_PKTLIMIT_2; + } else { + /* original packet format */ + np->desc_ver = DESC_VER_1; } - + + np->pkt_limit = NV_PKTLIMIT_1; + if (id->driver_data & DEV_HAS_LARGEDESC) + np->pkt_limit = NV_PKTLIMIT_2; + err = -ENOMEM; np->base = ioremap(addr, NV_PCI_REGSZ); if (!np->base) goto out_relreg; dev->base_addr = (unsigned long)np->base; + dev->irq = pci_dev->irq; - np->rx_ring = pci_alloc_consistent(pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), - &np->ring_addr); - if (!np->rx_ring) - goto out_unmap; - np->tx_ring = &np->rx_ring[RX_RING]; + + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) { + np->rx_ring.orig = pci_alloc_consistent(pci_dev, + sizeof(struct ring_desc) * (RX_RING + TX_RING), + &np->ring_addr); + if (!np->rx_ring.orig) + goto out_unmap; + np->tx_ring.orig = &np->rx_ring.orig[RX_RING]; + } else { + np->rx_ring.ex = pci_alloc_consistent(pci_dev, + sizeof(struct ring_desc_ex) * (RX_RING + TX_RING), + &np->ring_addr); + if (!np->rx_ring.ex) + goto out_unmap; + np->tx_ring.ex = &np->rx_ring.ex[RX_RING]; + } dev->open = nv_open; dev->stop = nv_close; @@ -2313,8 +2418,12 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i return 0; out_freering: - pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), - np->rx_ring, np->ring_addr); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), + np->rx_ring.orig, np->ring_addr); + else + pci_free_consistent(np->pci_dev, sizeof(struct ring_desc_ex) * (RX_RING + TX_RING), + np->rx_ring.ex, np->ring_addr); pci_set_drvdata(pci_dev, NULL); out_unmap: iounmap(get_hwbase(dev)); @@ -2343,7 +2452,10 @@ static void __devexit nv_remove(struct pci_dev *pci_dev) writel(np->orig_mac[1], base + NvRegMacAddrB); /* free all structures */ - pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), np->rx_ring, np->ring_addr); + if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) + pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), np->rx_ring.orig, np->ring_addr); + else + pci_free_consistent(np->pci_dev, sizeof(struct ring_desc_ex) * (RX_RING + TX_RING), np->rx_ring.ex, np->ring_addr); iounmap(get_hwbase(dev)); pci_release_regions(pci_dev); pci_disable_device(pci_dev); @@ -2382,35 +2494,35 @@ static struct pci_device_id pci_tbl[] = { }, { /* CK804 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_8), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA, }, { /* CK804 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_9), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA, }, { /* MCP04 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_10), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA, }, { /* MCP04 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_11), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA, }, { /* MCP51 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_12), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_HIGH_DMA, }, { /* MCP51 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_13), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_HIGH_DMA, }, { /* MCP55 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_14), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA, }, { /* MCP55 Ethernet Controller */ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_15), - .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC, + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_HIGH_DMA, }, {0,}, }; -- cgit v0.10.2 From 72b317825728942383b0c2e35016d29bbfb4df00 Mon Sep 17 00:00:00 2001 From: Manfred Spraul Date: Sun, 31 Jul 2005 18:33:34 +0200 Subject: [PATCH] forcedeth: Add set_mac_address support This is a multi-part message in MIME format. Signed-off-by: Jeff Garzik diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 4d38acb..1e69102 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -90,6 +90,7 @@ * 0.38: 16 Jul 2005: tx irq rewrite: Use global flags instead of * per-packet flags. * 0.39: 18 Jul 2005: Add 64bit descriptor support. + * 0.40: 19 Jul 2005: Add support for mac address change. * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -101,7 +102,7 @@ * DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few * superfluous timer interrupts from the nic. */ -#define FORCEDETH_VERSION "0.39" +#define FORCEDETH_VERSION "0.40" #define DRV_NAME "forcedeth" #include @@ -1416,6 +1417,54 @@ static int nv_change_mtu(struct net_device *dev, int new_mtu) return 0; } +static void nv_copy_mac_to_hw(struct net_device *dev) +{ + u8 *base = get_hwbase(dev); + u32 mac[2]; + + mac[0] = (dev->dev_addr[0] << 0) + (dev->dev_addr[1] << 8) + + (dev->dev_addr[2] << 16) + (dev->dev_addr[3] << 24); + mac[1] = (dev->dev_addr[4] << 0) + (dev->dev_addr[5] << 8); + + writel(mac[0], base + NvRegMacAddrA); + writel(mac[1], base + NvRegMacAddrB); +} + +/* + * nv_set_mac_address: dev->set_mac_address function + * Called with rtnl_lock() held. + */ +static int nv_set_mac_address(struct net_device *dev, void *addr) +{ + struct fe_priv *np = get_nvpriv(dev); + struct sockaddr *macaddr = (struct sockaddr*)addr; + + if(!is_valid_ether_addr(macaddr->sa_data)) + return -EADDRNOTAVAIL; + + /* synchronized against open : rtnl_lock() held by caller */ + memcpy(dev->dev_addr, macaddr->sa_data, ETH_ALEN); + + if (netif_running(dev)) { + spin_lock_bh(&dev->xmit_lock); + spin_lock_irq(&np->lock); + + /* stop rx engine */ + nv_stop_rx(dev); + + /* set mac address */ + nv_copy_mac_to_hw(dev); + + /* restart rx engine */ + nv_start_rx(dev); + spin_unlock_irq(&np->lock); + spin_unlock_bh(&dev->xmit_lock); + } else { + nv_copy_mac_to_hw(dev); + } + return 0; +} + /* * nv_set_multicast: dev->set_multicast function * Called with dev->xmit_lock held. @@ -2047,16 +2096,7 @@ static int nv_open(struct net_device *dev) np->in_shutdown = 0; /* 3) set mac address */ - { - u32 mac[2]; - - mac[0] = (dev->dev_addr[0] << 0) + (dev->dev_addr[1] << 8) + - (dev->dev_addr[2] << 16) + (dev->dev_addr[3] << 24); - mac[1] = (dev->dev_addr[4] << 0) + (dev->dev_addr[5] << 8); - - writel(mac[0], base + NvRegMacAddrA); - writel(mac[1], base + NvRegMacAddrB); - } + nv_copy_mac_to_hw(dev); /* 4) give hw rings */ writel((u32) np->ring_addr, base + NvRegRxRingPhysAddr); @@ -2302,6 +2342,7 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i dev->hard_start_xmit = nv_start_xmit; dev->get_stats = nv_get_stats; dev->change_mtu = nv_change_mtu; + dev->set_mac_address = nv_set_mac_address; dev->set_multicast_list = nv_set_multicast; #ifdef CONFIG_NET_POLL_CONTROLLER dev->poll_controller = nv_poll_controller; -- cgit v0.10.2 From b3df9f813bc7b9db62ae0c90b8990b1cebf97345 Mon Sep 17 00:00:00 2001 From: Manfred Spraul Date: Sun, 31 Jul 2005 18:38:58 +0200 Subject: [PATCH] forcedeth: write back original mac address during ifdown This is a multi-part message in MIME format. Signed-off-by: Jeff Garzik diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 1e69102..f165ae9 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -91,6 +91,8 @@ * per-packet flags. * 0.39: 18 Jul 2005: Add 64bit descriptor support. * 0.40: 19 Jul 2005: Add support for mac address change. + * 0.41: 30 Jul 2005: Write back original MAC in nv_close instead + * of nv_remove * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -102,7 +104,7 @@ * DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few * superfluous timer interrupts from the nic. */ -#define FORCEDETH_VERSION "0.40" +#define FORCEDETH_VERSION "0.41" #define DRV_NAME "forcedeth" #include @@ -2230,6 +2232,12 @@ static int nv_close(struct net_device *dev) if (np->wolenabled) nv_start_rx(dev); + /* special op: write back the misordered MAC address - otherwise + * the next nv_probe would see a wrong address. + */ + writel(np->orig_mac[0], base + NvRegMacAddrA); + writel(np->orig_mac[1], base + NvRegMacAddrB); + /* FIXME: power down nic */ return 0; @@ -2482,16 +2490,9 @@ static void __devexit nv_remove(struct pci_dev *pci_dev) { struct net_device *dev = pci_get_drvdata(pci_dev); struct fe_priv *np = get_nvpriv(dev); - u8 __iomem *base = get_hwbase(dev); unregister_netdev(dev); - /* special op: write back the misordered MAC address - otherwise - * the next nv_probe would see a wrong address. - */ - writel(np->orig_mac[0], base + NvRegMacAddrA); - writel(np->orig_mac[1], base + NvRegMacAddrB); - /* free all structures */ if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (RX_RING + TX_RING), np->rx_ring.orig, np->ring_addr); -- cgit v0.10.2 From 20346722ec474245446bcbf460594a935a5c0512 Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:24:33 -0700 Subject: [PATCH] S2io: Code cleanup Hi, We are submitting a series of 13 patches to support our Xframe I and Xframe II line of products. The patches can be categorized as follows: Patches 1-8 : Changes applicable to both Xframe I and II Patches 9-11: Xframe II specific features Patch 12: Addresses issues found during testing cycle. Patch 13: Incorpoates mostly the review comments from community and some last moment bug fixes. Please review the patches and let us know your comments. Starting with patch 1 below. This patch involves cosmetic changes(tabs and indentation, regrouping of transmit and receive data structures, typecasting, code cleanup). Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io-regs.h b/drivers/net/s2io-regs.h index 7092ca6..8746740 100644 --- a/drivers/net/s2io-regs.h +++ b/drivers/net/s2io-regs.h @@ -77,19 +77,18 @@ typedef struct _XENA_dev_config { #define ADAPTER_ECC_EN BIT(55) u64 serr_source; -#define SERR_SOURCE_PIC BIT(0) -#define SERR_SOURCE_TXDMA BIT(1) -#define SERR_SOURCE_RXDMA BIT(2) +#define SERR_SOURCE_PIC BIT(0) +#define SERR_SOURCE_TXDMA BIT(1) +#define SERR_SOURCE_RXDMA BIT(2) #define SERR_SOURCE_MAC BIT(3) #define SERR_SOURCE_MC BIT(4) #define SERR_SOURCE_XGXS BIT(5) -#define SERR_SOURCE_ANY (SERR_SOURCE_PIC | \ - SERR_SOURCE_TXDMA | \ - SERR_SOURCE_RXDMA | \ - SERR_SOURCE_MAC | \ - SERR_SOURCE_MC | \ - SERR_SOURCE_XGXS) - +#define SERR_SOURCE_ANY (SERR_SOURCE_PIC | \ + SERR_SOURCE_TXDMA | \ + SERR_SOURCE_RXDMA | \ + SERR_SOURCE_MAC | \ + SERR_SOURCE_MC | \ + SERR_SOURCE_XGXS) u8 unused_0[0x800 - 0x120]; diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index ea638b1..0721e78 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -11,29 +11,28 @@ * See the file COPYING in this distribution for more information. * * Credits: - * Jeff Garzik : For pointing out the improper error condition - * check in the s2io_xmit routine and also some - * issues in the Tx watch dog function. Also for - * patiently answering all those innumerable + * Jeff Garzik : For pointing out the improper error condition + * check in the s2io_xmit routine and also some + * issues in the Tx watch dog function. Also for + * patiently answering all those innumerable * questions regaring the 2.6 porting issues. * Stephen Hemminger : Providing proper 2.6 porting mechanism for some * macros available only in 2.6 Kernel. - * Francois Romieu : For pointing out all code part that were + * Francois Romieu : For pointing out all code part that were * deprecated and also styling related comments. - * Grant Grundler : For helping me get rid of some Architecture + * Grant Grundler : For helping me get rid of some Architecture * dependent code. * Christopher Hellwig : Some more 2.6 specific issues in the driver. - * + * * The module loadable parameters that are supported by the driver and a brief * explaination of all the variables. - * rx_ring_num : This can be used to program the number of receive rings used - * in the driver. - * rx_ring_len: This defines the number of descriptors each ring can have. This + * rx_ring_num : This can be used to program the number of receive rings used + * in the driver. + * rx_ring_len: This defines the number of descriptors each ring can have. This * is also an array of size 8. * tx_fifo_num: This defines the number of Tx FIFOs thats used int the driver. - * tx_fifo_len: This too is an array of 8. Each element defines the number of + * tx_fifo_len: This too is an array of 8. Each element defines the number of * Tx descriptors that can be associated with each corresponding FIFO. - * in PCI Configuration space. ************************************************************************/ #include @@ -57,19 +56,19 @@ #include #include -#include #include #include +#include /* local include */ #include "s2io.h" #include "s2io-regs.h" /* S2io Driver name & version. */ -static char s2io_driver_name[] = "s2io"; -static char s2io_driver_version[] = "Version 1.7.7.1"; +static char s2io_driver_name[] = "Neterion"; +static char s2io_driver_version[] = "Version 1.7.7"; -/* +/* * Cards with following subsystem_id have a link state indication * problem, 600B, 600C, 600D, 640B, 640C and 640D. * macro below identifies these cards given the subsystem_id. @@ -86,9 +85,13 @@ static char s2io_driver_version[] = "Version 1.7.7.1"; static inline int rx_buffer_level(nic_t * sp, int rxb_size, int ring) { int level = 0; - if ((sp->pkt_cnt[ring] - rxb_size) > 16) { + mac_info_t *mac_control; + + mac_control = &sp->mac_control; + if ((mac_control->rings[ring].pkt_cnt - rxb_size) > 16) { level = LOW; - if ((sp->pkt_cnt[ring] - rxb_size) < MAX_RXDS_PER_BLOCK) { + if ((mac_control->rings[ring].pkt_cnt - rxb_size) < + MAX_RXDS_PER_BLOCK) { level = PANIC; } } @@ -153,8 +156,7 @@ static char ethtool_stats_keys[][ETH_GSTRING_LEN] = { #define S2IO_TEST_LEN sizeof(s2io_gstrings) / ETH_GSTRING_LEN #define S2IO_STRINGS_LEN S2IO_TEST_LEN * ETH_GSTRING_LEN - -/* +/* * Constants to be programmed into the Xena's registers, to configure * the XAUI. */ @@ -196,8 +198,7 @@ static u64 default_dtx_cfg[] = { END_SIGN }; - -/* +/* * Constants for Fixing the MacAddress problem seen mostly on * Alpha machines. */ @@ -227,6 +228,8 @@ static unsigned int rx_ring_num = 1; static unsigned int rx_ring_sz[MAX_RX_RINGS] = {[0 ...(MAX_RX_RINGS - 1)] = 0 }; static unsigned int Stats_refresh_time = 4; +static unsigned int rts_frm_len[MAX_RX_RINGS] = + {[0 ...(MAX_RX_RINGS - 1)] = 0 }; static unsigned int rmac_pause_time = 65535; static unsigned int mc_pause_threshold_q0q3 = 187; static unsigned int mc_pause_threshold_q4q7 = 187; @@ -237,9 +240,9 @@ static unsigned int rmac_util_period = 5; static unsigned int indicate_max_pkts; #endif -/* +/* * S2IO device table. - * This table lists all the devices that this driver supports. + * This table lists all the devices that this driver supports. */ static struct pci_device_id s2io_tbl[] __devinitdata = { {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_WIN, @@ -247,9 +250,9 @@ static struct pci_device_id s2io_tbl[] __devinitdata = { {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_UNI, PCI_ANY_ID, PCI_ANY_ID}, {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_WIN, - PCI_ANY_ID, PCI_ANY_ID}, - {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI, - PCI_ANY_ID, PCI_ANY_ID}, + PCI_ANY_ID, PCI_ANY_ID}, + {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI, + PCI_ANY_ID, PCI_ANY_ID}, {0,} }; @@ -268,8 +271,8 @@ static struct pci_driver s2io_driver = { /** * init_shared_mem - Allocation and Initialization of Memory * @nic: Device private variable. - * Description: The function allocates all the memory areas shared - * between the NIC and the driver. This includes Tx descriptors, + * Description: The function allocates all the memory areas shared + * between the NIC and the driver. This includes Tx descriptors, * Rx descriptors and the statistics block. */ @@ -279,11 +282,11 @@ static int init_shared_mem(struct s2io_nic *nic) void *tmp_v_addr, *tmp_v_addr_next; dma_addr_t tmp_p_addr, tmp_p_addr_next; RxD_block_t *pre_rxd_blk = NULL; - int i, j, blk_cnt; + int i, j, blk_cnt, rx_sz, tx_sz; int lst_size, lst_per_page; struct net_device *dev = nic->dev; #ifdef CONFIG_2BUFF_MODE - unsigned long tmp; + u64 tmp; buffAdd_t *ba; #endif @@ -308,28 +311,34 @@ static int init_shared_mem(struct s2io_nic *nic) } lst_size = (sizeof(TxD_t) * config->max_txds); + tx_sz = lst_size * size; lst_per_page = PAGE_SIZE / lst_size; for (i = 0; i < config->tx_fifo_num; i++) { int fifo_len = config->tx_cfg[i].fifo_len; int list_holder_size = fifo_len * sizeof(list_info_hold_t); - nic->list_info[i] = kmalloc(list_holder_size, GFP_KERNEL); - if (!nic->list_info[i]) { + mac_control->fifos[i].list_info = kmalloc(list_holder_size, + GFP_KERNEL); + if (!mac_control->fifos[i].list_info) { DBG_PRINT(ERR_DBG, "Malloc failed for list_info\n"); return -ENOMEM; } - memset(nic->list_info[i], 0, list_holder_size); + memset(mac_control->fifos[i].list_info, 0, list_holder_size); } for (i = 0; i < config->tx_fifo_num; i++) { int page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len, lst_per_page); - mac_control->tx_curr_put_info[i].offset = 0; - mac_control->tx_curr_put_info[i].fifo_len = + mac_control->fifos[i].tx_curr_put_info.offset = 0; + mac_control->fifos[i].tx_curr_put_info.fifo_len = config->tx_cfg[i].fifo_len - 1; - mac_control->tx_curr_get_info[i].offset = 0; - mac_control->tx_curr_get_info[i].fifo_len = + mac_control->fifos[i].tx_curr_get_info.offset = 0; + mac_control->fifos[i].tx_curr_get_info.fifo_len = config->tx_cfg[i].fifo_len - 1; + mac_control->fifos[i].fifo_no = i; + mac_control->fifos[i].nic = nic; + mac_control->fifos[i].max_txds = MAX_SKB_FRAGS; + for (j = 0; j < page_num; j++) { int k = 0; dma_addr_t tmp_p; @@ -345,16 +354,15 @@ static int init_shared_mem(struct s2io_nic *nic) while (k < lst_per_page) { int l = (j * lst_per_page) + k; if (l == config->tx_cfg[i].fifo_len) - goto end_txd_alloc; - nic->list_info[i][l].list_virt_addr = + break; + mac_control->fifos[i].list_info[l].list_virt_addr = tmp_v + (k * lst_size); - nic->list_info[i][l].list_phy_addr = + mac_control->fifos[i].list_info[l].list_phy_addr = tmp_p + (k * lst_size); k++; } } } - end_txd_alloc: /* Allocation and initialization of RXDs in Rings */ size = 0; @@ -367,21 +375,26 @@ static int init_shared_mem(struct s2io_nic *nic) return FAILURE; } size += config->rx_cfg[i].num_rxd; - nic->block_count[i] = + mac_control->rings[i].block_count = config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1); - nic->pkt_cnt[i] = - config->rx_cfg[i].num_rxd - nic->block_count[i]; + mac_control->rings[i].pkt_cnt = + config->rx_cfg[i].num_rxd - mac_control->rings[i].block_count; } + size = (size * (sizeof(RxD_t))); + rx_sz = size; for (i = 0; i < config->rx_ring_num; i++) { - mac_control->rx_curr_get_info[i].block_index = 0; - mac_control->rx_curr_get_info[i].offset = 0; - mac_control->rx_curr_get_info[i].ring_len = + mac_control->rings[i].rx_curr_get_info.block_index = 0; + mac_control->rings[i].rx_curr_get_info.offset = 0; + mac_control->rings[i].rx_curr_get_info.ring_len = config->rx_cfg[i].num_rxd - 1; - mac_control->rx_curr_put_info[i].block_index = 0; - mac_control->rx_curr_put_info[i].offset = 0; - mac_control->rx_curr_put_info[i].ring_len = + mac_control->rings[i].rx_curr_put_info.block_index = 0; + mac_control->rings[i].rx_curr_put_info.offset = 0; + mac_control->rings[i].rx_curr_put_info.ring_len = config->rx_cfg[i].num_rxd - 1; + mac_control->rings[i].nic = nic; + mac_control->rings[i].ring_no = i; + blk_cnt = config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1); /* Allocating all the Rx blocks */ @@ -395,32 +408,36 @@ static int init_shared_mem(struct s2io_nic *nic) &tmp_p_addr); if (tmp_v_addr == NULL) { /* - * In case of failure, free_shared_mem() - * is called, which should free any - * memory that was alloced till the + * In case of failure, free_shared_mem() + * is called, which should free any + * memory that was alloced till the * failure happened. */ - nic->rx_blocks[i][j].block_virt_addr = + mac_control->rings[i].rx_blocks[j].block_virt_addr = tmp_v_addr; return -ENOMEM; } memset(tmp_v_addr, 0, size); - nic->rx_blocks[i][j].block_virt_addr = tmp_v_addr; - nic->rx_blocks[i][j].block_dma_addr = tmp_p_addr; + mac_control->rings[i].rx_blocks[j].block_virt_addr = + tmp_v_addr; + mac_control->rings[i].rx_blocks[j].block_dma_addr = + tmp_p_addr; } /* Interlinking all Rx Blocks */ for (j = 0; j < blk_cnt; j++) { - tmp_v_addr = nic->rx_blocks[i][j].block_virt_addr; + tmp_v_addr = + mac_control->rings[i].rx_blocks[j].block_virt_addr; tmp_v_addr_next = - nic->rx_blocks[i][(j + 1) % + mac_control->rings[i].rx_blocks[(j + 1) % blk_cnt].block_virt_addr; - tmp_p_addr = nic->rx_blocks[i][j].block_dma_addr; + tmp_p_addr = + mac_control->rings[i].rx_blocks[j].block_dma_addr; tmp_p_addr_next = - nic->rx_blocks[i][(j + 1) % + mac_control->rings[i].rx_blocks[(j + 1) % blk_cnt].block_dma_addr; pre_rxd_blk = (RxD_block_t *) tmp_v_addr; - pre_rxd_blk->reserved_1 = END_OF_BLOCK; /* last RxD + pre_rxd_blk->reserved_1 = END_OF_BLOCK; /* last RxD * marker. */ #ifndef CONFIG_2BUFF_MODE @@ -433,43 +450,43 @@ static int init_shared_mem(struct s2io_nic *nic) } #ifdef CONFIG_2BUFF_MODE - /* + /* * Allocation of Storages for buffer addresses in 2BUFF mode * and the buffers as well. */ for (i = 0; i < config->rx_ring_num; i++) { blk_cnt = config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1); - nic->ba[i] = kmalloc((sizeof(buffAdd_t *) * blk_cnt), + mac_control->rings[i].ba = kmalloc((sizeof(buffAdd_t *) * blk_cnt), GFP_KERNEL); - if (!nic->ba[i]) + if (!mac_control->rings[i].ba) return -ENOMEM; for (j = 0; j < blk_cnt; j++) { int k = 0; - nic->ba[i][j] = kmalloc((sizeof(buffAdd_t) * + mac_control->rings[i].ba[j] = kmalloc((sizeof(buffAdd_t) * (MAX_RXDS_PER_BLOCK + 1)), GFP_KERNEL); - if (!nic->ba[i][j]) + if (!mac_control->rings[i].ba[j]) return -ENOMEM; while (k != MAX_RXDS_PER_BLOCK) { - ba = &nic->ba[i][j][k]; + ba = &mac_control->rings[i].ba[j][k]; - ba->ba_0_org = kmalloc + ba->ba_0_org = (void *) kmalloc (BUF0_LEN + ALIGN_SIZE, GFP_KERNEL); if (!ba->ba_0_org) return -ENOMEM; - tmp = (unsigned long) ba->ba_0_org; + tmp = (u64) ba->ba_0_org; tmp += ALIGN_SIZE; - tmp &= ~((unsigned long) ALIGN_SIZE); + tmp &= ~((u64) ALIGN_SIZE); ba->ba_0 = (void *) tmp; - ba->ba_1_org = kmalloc + ba->ba_1_org = (void *) kmalloc (BUF1_LEN + ALIGN_SIZE, GFP_KERNEL); if (!ba->ba_1_org) return -ENOMEM; - tmp = (unsigned long) ba->ba_1_org; + tmp = (u64) ba->ba_1_org; tmp += ALIGN_SIZE; - tmp &= ~((unsigned long) ALIGN_SIZE); + tmp &= ~((u64) ALIGN_SIZE); ba->ba_1 = (void *) tmp; k++; } @@ -483,9 +500,9 @@ static int init_shared_mem(struct s2io_nic *nic) (nic->pdev, size, &mac_control->stats_mem_phy); if (!mac_control->stats_mem) { - /* - * In case of failure, free_shared_mem() is called, which - * should free any memory that was alloced till the + /* + * In case of failure, free_shared_mem() is called, which + * should free any memory that was alloced till the * failure happened. */ return -ENOMEM; @@ -495,15 +512,14 @@ static int init_shared_mem(struct s2io_nic *nic) tmp_v_addr = mac_control->stats_mem; mac_control->stats_info = (StatInfo_t *) tmp_v_addr; memset(tmp_v_addr, 0, size); - DBG_PRINT(INIT_DBG, "%s:Ring Mem PHY: 0x%llx\n", dev->name, (unsigned long long) tmp_p_addr); return SUCCESS; } -/** - * free_shared_mem - Free the allocated Memory +/** + * free_shared_mem - Free the allocated Memory * @nic: Device private variable. * Description: This function is to free all memory locations allocated by * the init_shared_mem() function and return it to the kernel. @@ -533,15 +549,18 @@ static void free_shared_mem(struct s2io_nic *nic) lst_per_page); for (j = 0; j < page_num; j++) { int mem_blks = (j * lst_per_page); - if (!nic->list_info[i][mem_blks].list_virt_addr) + if (!mac_control->fifos[i].list_info[mem_blks]. + list_virt_addr) break; pci_free_consistent(nic->pdev, PAGE_SIZE, - nic->list_info[i][mem_blks]. + mac_control->fifos[i]. + list_info[mem_blks]. list_virt_addr, - nic->list_info[i][mem_blks]. + mac_control->fifos[i]. + list_info[mem_blks]. list_phy_addr); } - kfree(nic->list_info[i]); + kfree(mac_control->fifos[i].list_info); } #ifndef CONFIG_2BUFF_MODE @@ -550,10 +569,12 @@ static void free_shared_mem(struct s2io_nic *nic) size = SIZE_OF_BLOCK; #endif for (i = 0; i < config->rx_ring_num; i++) { - blk_cnt = nic->block_count[i]; + blk_cnt = mac_control->rings[i].block_count; for (j = 0; j < blk_cnt; j++) { - tmp_v_addr = nic->rx_blocks[i][j].block_virt_addr; - tmp_p_addr = nic->rx_blocks[i][j].block_dma_addr; + tmp_v_addr = mac_control->rings[i].rx_blocks[j]. + block_virt_addr; + tmp_p_addr = mac_control->rings[i].rx_blocks[j]. + block_dma_addr; if (tmp_v_addr == NULL) break; pci_free_consistent(nic->pdev, size, @@ -566,35 +587,21 @@ static void free_shared_mem(struct s2io_nic *nic) for (i = 0; i < config->rx_ring_num; i++) { blk_cnt = config->rx_cfg[i].num_rxd / (MAX_RXDS_PER_BLOCK + 1); - if (!nic->ba[i]) - goto end_free; for (j = 0; j < blk_cnt; j++) { int k = 0; - if (!nic->ba[i][j]) { - kfree(nic->ba[i]); - goto end_free; - } + if (!mac_control->rings[i].ba[j]) + continue; while (k != MAX_RXDS_PER_BLOCK) { - buffAdd_t *ba = &nic->ba[i][j][k]; - if (!ba || !ba->ba_0_org || !ba->ba_1_org) - { - kfree(nic->ba[i]); - kfree(nic->ba[i][j]); - if(ba->ba_0_org) - kfree(ba->ba_0_org); - if(ba->ba_1_org) - kfree(ba->ba_1_org); - goto end_free; - } + buffAdd_t *ba = &mac_control->rings[i].ba[j][k]; kfree(ba->ba_0_org); kfree(ba->ba_1_org); k++; } - kfree(nic->ba[i][j]); + kfree(mac_control->rings[i].ba[j]); } - kfree(nic->ba[i]); + if (mac_control->rings[i].ba) + kfree(mac_control->rings[i].ba); } -end_free: #endif if (mac_control->stats_mem) { @@ -605,12 +612,12 @@ end_free: } } -/** - * init_nic - Initialization of hardware +/** + * init_nic - Initialization of hardware * @nic: device peivate variable - * Description: The function sequentially configures every block - * of the H/W from their reset values. - * Return Value: SUCCESS on success and + * Description: The function sequentially configures every block + * of the H/W from their reset values. + * Return Value: SUCCESS on success and * '-1' on failure (endian settings incorrect). */ @@ -626,12 +633,13 @@ static int init_nic(struct s2io_nic *nic) struct config_param *config; int mdio_cnt = 0, dtx_cnt = 0; unsigned long long mem_share; + int mem_size; mac_control = &nic->mac_control; config = &nic->config; - /* Initialize swapper control register */ - if (s2io_set_swapper(nic)) { + /* to set the swapper control on the card */ + if(s2io_set_swapper(nic)) { DBG_PRINT(ERR_DBG,"ERROR: Setting Swapper failed\n"); return -1; } @@ -639,8 +647,8 @@ static int init_nic(struct s2io_nic *nic) /* Remove XGXS from reset state */ val64 = 0; writeq(val64, &bar0->sw_reset); - val64 = readq(&bar0->sw_reset); msleep(500); + val64 = readq(&bar0->sw_reset); /* Enable Receiving broadcasts */ add = &bar0->mac_cfg; @@ -660,18 +668,18 @@ static int init_nic(struct s2io_nic *nic) val64 = dev->mtu; writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len); - /* - * Configuring the XAUI Interface of Xena. + /* + * Configuring the XAUI Interface of Xena. * *************************************** - * To Configure the Xena's XAUI, one has to write a series - * of 64 bit values into two registers in a particular - * sequence. Hence a macro 'SWITCH_SIGN' has been defined - * which will be defined in the array of configuration values - * (default_dtx_cfg & default_mdio_cfg) at appropriate places - * to switch writing from one regsiter to another. We continue + * To Configure the Xena's XAUI, one has to write a series + * of 64 bit values into two registers in a particular + * sequence. Hence a macro 'SWITCH_SIGN' has been defined + * which will be defined in the array of configuration values + * (default_dtx_cfg & default_mdio_cfg) at appropriate places + * to switch writing from one regsiter to another. We continue * writing these values until we encounter the 'END_SIGN' macro. - * For example, After making a series of 21 writes into - * dtx_control register the 'SWITCH_SIGN' appears and hence we + * For example, After making a series of 21 writes into + * dtx_control register the 'SWITCH_SIGN' appears and hence we * start writing into mdio_control until we encounter END_SIGN. */ while (1) { @@ -752,8 +760,8 @@ static int init_nic(struct s2io_nic *nic) DBG_PRINT(INIT_DBG, "Fifo partition at: 0x%p is: 0x%llx\n", &bar0->tx_fifo_partition_0, (unsigned long long) val64); - /* - * Initialization of Tx_PA_CONFIG register to ignore packet + /* + * Initialization of Tx_PA_CONFIG register to ignore packet * integrity checking. */ val64 = readq(&bar0->tx_pa_cfg); @@ -770,54 +778,54 @@ static int init_nic(struct s2io_nic *nic) } writeq(val64, &bar0->rx_queue_priority); - /* - * Allocating equal share of memory to all the + /* + * Allocating equal share of memory to all the * configured Rings. */ val64 = 0; + mem_size = 64; for (i = 0; i < config->rx_ring_num; i++) { switch (i) { case 0: - mem_share = (64 / config->rx_ring_num + - 64 % config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num + + mem_size % config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q0_SZ(mem_share); continue; case 1: - mem_share = (64 / config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q1_SZ(mem_share); continue; case 2: - mem_share = (64 / config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q2_SZ(mem_share); continue; case 3: - mem_share = (64 / config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q3_SZ(mem_share); continue; case 4: - mem_share = (64 / config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q4_SZ(mem_share); continue; case 5: - mem_share = (64 / config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q5_SZ(mem_share); continue; case 6: - mem_share = (64 / config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q6_SZ(mem_share); continue; case 7: - mem_share = (64 / config->rx_ring_num); + mem_share = (mem_size / config->rx_ring_num); val64 |= RX_QUEUE_CFG_Q7_SZ(mem_share); continue; } } writeq(val64, &bar0->rx_queue_cfg); - /* - * Initializing the Tx round robin registers to 0. - * Filling Tx and Rx round robin registers as per the - * number of FIFOs and Rings is still TODO. + /* Initializing the Tx round robin registers to 0 + * filling tx and rx round robin registers as per + * the number of FIFOs and Rings is still TODO */ writeq(0, &bar0->tx_w_round_robin_0); writeq(0, &bar0->tx_w_round_robin_1); @@ -825,30 +833,30 @@ static int init_nic(struct s2io_nic *nic) writeq(0, &bar0->tx_w_round_robin_3); writeq(0, &bar0->tx_w_round_robin_4); - /* + /* * TODO - * Disable Rx steering. Hard coding all packets be steered to - * Queue 0 for now. + * Disable Rx steering. Hard coding all packets to be steered to + * Queue 0 for now. */ val64 = 0x8080808080808080ULL; writeq(val64, &bar0->rts_qos_steering); /* UDP Fix */ val64 = 0; - for (i = 1; i < 8; i++) + for (i = 0; i < 8; i++) writeq(val64, &bar0->rts_frm_len_n[i]); - /* Set rts_frm_len register for fifo 0 */ - writeq(MAC_RTS_FRM_LEN_SET(dev->mtu + 22), - &bar0->rts_frm_len_n[0]); + /* Set the default rts frame length for ring0 */ + writeq(MAC_RTS_FRM_LEN_SET(dev->mtu+22), + &bar0->rts_frm_len_n[0]); - /* Enable statistics */ + /* Program statistics memory */ writeq(mac_control->stats_mem_phy, &bar0->stat_addr); val64 = SET_UPDT_PERIOD(Stats_refresh_time) | STAT_CFG_STAT_RO | STAT_CFG_STAT_EN; writeq(val64, &bar0->stat_cfg); - /* + /* * Initializing the sampling rate for the device to calculate the * bandwidth utilization. */ @@ -857,11 +865,12 @@ static int init_nic(struct s2io_nic *nic) writeq(val64, &bar0->mac_link_util); - /* - * Initializing the Transmit and Receive Traffic Interrupt + /* + * Initializing the Transmit and Receive Traffic Interrupt * Scheme. */ - /* TTI Initialization. Default Tx timer gets us about + /* + * TTI Initialization. Default Tx timer gets us about * 250 interrupts per sec. Continuous interrupts are enabled * by default. */ @@ -880,7 +889,7 @@ static int init_nic(struct s2io_nic *nic) val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD; writeq(val64, &bar0->tti_command_mem); - /* + /* * Once the operation completes, the Strobe bit of the command * register will be reset. We poll for this particular condition * We wait for a maximum of 500ms for the operation to complete, @@ -917,7 +926,7 @@ static int init_nic(struct s2io_nic *nic) val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD; writeq(val64, &bar0->rti_command_mem); - /* + /* * Once the operation completes, the Strobe bit of the command * register will be reset. We poll for this particular condition * We wait for a maximum of 500ms for the operation to complete, @@ -926,7 +935,7 @@ static int init_nic(struct s2io_nic *nic) time = 0; while (TRUE) { val64 = readq(&bar0->rti_command_mem); - if (!(val64 & TTI_CMD_MEM_STROBE_NEW_CMD)) { + if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD)) { break; } if (time > 10) { @@ -938,15 +947,15 @@ static int init_nic(struct s2io_nic *nic) msleep(50); } - /* - * Initializing proper values as Pause threshold into all + /* + * Initializing proper values as Pause threshold into all * the 8 Queues on Rx side. */ writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q0q3); writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q4q7); /* Disable RMAC PAD STRIPPING */ - add = &bar0->mac_cfg; + add = (void *) &bar0->mac_cfg; val64 = readq(&bar0->mac_cfg); val64 &= ~(MAC_CFG_RMAC_STRIP_PAD); writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key); @@ -955,8 +964,8 @@ static int init_nic(struct s2io_nic *nic) writel((u32) (val64 >> 32), (add + 4)); val64 = readq(&bar0->mac_cfg); - /* - * Set the time value to be inserted in the pause frame + /* + * Set the time value to be inserted in the pause frame * generated by xena. */ val64 = readq(&bar0->rmac_pause_cfg); @@ -964,7 +973,7 @@ static int init_nic(struct s2io_nic *nic) val64 |= RMAC_PAUSE_HG_PTIME(nic->mac_control.rmac_pause_time); writeq(val64, &bar0->rmac_pause_cfg); - /* + /* * Set the Threshold Limit for Generating the pause frame * If the amount of data in any Queue exceeds ratio of * (mac_control.mc_pause_threshold_q0q3 or q4q7)/256 @@ -988,8 +997,8 @@ static int init_nic(struct s2io_nic *nic) } writeq(val64, &bar0->mc_pause_thresh_q4q7); - /* - * TxDMA will stop Read request if the number of read split has + /* + * TxDMA will stop Read request if the number of read split has * exceeded the limit pointed by shared_splits */ val64 = readq(&bar0->pic_control); @@ -999,14 +1008,14 @@ static int init_nic(struct s2io_nic *nic) return SUCCESS; } -/** - * en_dis_able_nic_intrs - Enable or Disable the interrupts +/** + * en_dis_able_nic_intrs - Enable or Disable the interrupts * @nic: device private variable, * @mask: A mask indicating which Intr block must be modified and, * @flag: A flag indicating whether to enable or disable the Intrs. * Description: This function will either disable or enable the interrupts - * depending on the flag argument. The mask argument can be used to - * enable/disable any Intr block. + * depending on the flag argument. The mask argument can be used to + * enable/disable any Intr block. * Return Value: NONE. */ @@ -1024,20 +1033,20 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 = readq(&bar0->general_int_mask); temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); - /* + /* * Disabled all PCIX, Flash, MDIO, IIC and GPIO - * interrupts for now. - * TODO + * interrupts for now. + * TODO */ writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask); - /* + /* * No MSI Support is available presently, so TTI and * RTI interrupts are also disabled. */ } else if (flag == DISABLE_INTRS) { - /* - * Disable PIC Intrs in the general - * intr mask register + /* + * Disable PIC Intrs in the general + * intr mask register */ writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask); temp64 = readq(&bar0->general_int_mask); @@ -1055,27 +1064,27 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 = readq(&bar0->general_int_mask); temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); - /* - * Keep all interrupts other than PFC interrupt + /* + * Keep all interrupts other than PFC interrupt * and PCC interrupt disabled in DMA level. */ val64 = DISABLE_ALL_INTRS & ~(TXDMA_PFC_INT_M | TXDMA_PCC_INT_M); writeq(val64, &bar0->txdma_int_mask); - /* - * Enable only the MISC error 1 interrupt in PFC block + /* + * Enable only the MISC error 1 interrupt in PFC block */ val64 = DISABLE_ALL_INTRS & (~PFC_MISC_ERR_1); writeq(val64, &bar0->pfc_err_mask); - /* - * Enable only the FB_ECC error interrupt in PCC block + /* + * Enable only the FB_ECC error interrupt in PCC block */ val64 = DISABLE_ALL_INTRS & (~PCC_FB_ECC_ERR); writeq(val64, &bar0->pcc_err_mask); } else if (flag == DISABLE_INTRS) { - /* - * Disable TxDMA Intrs in the general intr mask - * register + /* + * Disable TxDMA Intrs in the general intr mask + * register */ writeq(DISABLE_ALL_INTRS, &bar0->txdma_int_mask); writeq(DISABLE_ALL_INTRS, &bar0->pfc_err_mask); @@ -1093,15 +1102,15 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 = readq(&bar0->general_int_mask); temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); - /* - * All RxDMA block interrupts are disabled for now - * TODO + /* + * All RxDMA block interrupts are disabled for now + * TODO */ writeq(DISABLE_ALL_INTRS, &bar0->rxdma_int_mask); } else if (flag == DISABLE_INTRS) { - /* - * Disable RxDMA Intrs in the general intr mask - * register + /* + * Disable RxDMA Intrs in the general intr mask + * register */ writeq(DISABLE_ALL_INTRS, &bar0->rxdma_int_mask); temp64 = readq(&bar0->general_int_mask); @@ -1118,8 +1127,8 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 = readq(&bar0->general_int_mask); temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); - /* - * All MAC block error interrupts are disabled for now + /* + * All MAC block error interrupts are disabled for now * except the link status change interrupt. * TODO */ @@ -1132,8 +1141,8 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) val64 &= ~((u64) RMAC_LINK_STATE_CHANGE_INT); writeq(val64, &bar0->mac_rmac_err_mask); } else if (flag == DISABLE_INTRS) { - /* - * Disable MAC Intrs in the general intr mask register + /* + * Disable MAC Intrs in the general intr mask register */ writeq(DISABLE_ALL_INTRS, &bar0->mac_int_mask); writeq(DISABLE_ALL_INTRS, @@ -1152,14 +1161,14 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 = readq(&bar0->general_int_mask); temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); - /* + /* * All XGXS block error interrupts are disabled for now - * TODO + * TODO */ writeq(DISABLE_ALL_INTRS, &bar0->xgxs_int_mask); } else if (flag == DISABLE_INTRS) { - /* - * Disable MC Intrs in the general intr mask register + /* + * Disable MC Intrs in the general intr mask register */ writeq(DISABLE_ALL_INTRS, &bar0->xgxs_int_mask); temp64 = readq(&bar0->general_int_mask); @@ -1175,9 +1184,9 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 = readq(&bar0->general_int_mask); temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); - /* - * All MC block error interrupts are disabled for now - * TODO + /* + * All MC block error interrupts are disabled for now. + * TODO */ writeq(DISABLE_ALL_INTRS, &bar0->mc_int_mask); } else if (flag == DISABLE_INTRS) { @@ -1199,14 +1208,14 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 = readq(&bar0->general_int_mask); temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); - /* + /* * Enable all the Tx side interrupts - * writing 0 Enables all 64 TX interrupt levels + * writing 0 Enables all 64 TX interrupt levels */ writeq(0x0, &bar0->tx_traffic_mask); } else if (flag == DISABLE_INTRS) { - /* - * Disable Tx Traffic Intrs in the general intr mask + /* + * Disable Tx Traffic Intrs in the general intr mask * register. */ writeq(DISABLE_ALL_INTRS, &bar0->tx_traffic_mask); @@ -1226,8 +1235,8 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) /* writing 0 Enables all 8 RX interrupt levels */ writeq(0x0, &bar0->rx_traffic_mask); } else if (flag == DISABLE_INTRS) { - /* - * Disable Rx Traffic Intrs in the general intr mask + /* + * Disable Rx Traffic Intrs in the general intr mask * register. */ writeq(DISABLE_ALL_INTRS, &bar0->rx_traffic_mask); @@ -1238,20 +1247,42 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) } } -/** - * verify_xena_quiescence - Checks whether the H/W is ready +static int check_prc_pcc_state(u64 val64, int flag) +{ + int ret = 0; + + if (flag == FALSE) { + if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) && + ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == + ADAPTER_STATUS_RC_PRC_QUIESCENT)) { + ret = 1; + } + } else { + if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) == + ADAPTER_STATUS_RMAC_PCC_IDLE) && + (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) || + ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == + ADAPTER_STATUS_RC_PRC_QUIESCENT))) { + ret = 1; + } + } + + return ret; +} +/** + * verify_xena_quiescence - Checks whether the H/W is ready * @val64 : Value read from adapter status register. * @flag : indicates if the adapter enable bit was ever written once * before. * Description: Returns whether the H/W is ready to go or not. Depending - * on whether adapter enable bit was written or not the comparison + * on whether adapter enable bit was written or not the comparison * differs and the calling function passes the input argument flag to * indicate this. - * Return: 1 If xena is quiescence + * Return: 1 If xena is quiescence * 0 If Xena is not quiescence */ -static int verify_xena_quiescence(u64 val64, int flag) +static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag) { int ret = 0; u64 tmp64 = ~((u64) val64); @@ -1263,25 +1294,7 @@ static int verify_xena_quiescence(u64 val64, int flag) ADAPTER_STATUS_PIC_QUIESCENT | ADAPTER_STATUS_MC_DRAM_READY | ADAPTER_STATUS_MC_QUEUES_READY | ADAPTER_STATUS_M_PLL_LOCK | ADAPTER_STATUS_P_PLL_LOCK))) { - if (flag == FALSE) { - if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) && - ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == - ADAPTER_STATUS_RC_PRC_QUIESCENT)) { - - ret = 1; - - } - } else { - if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) == - ADAPTER_STATUS_RMAC_PCC_IDLE) && - (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) || - ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == - ADAPTER_STATUS_RC_PRC_QUIESCENT))) { - - ret = 1; - - } - } + ret = check_prc_pcc_state(val64, flag); } return ret; @@ -1290,12 +1303,12 @@ static int verify_xena_quiescence(u64 val64, int flag) /** * fix_mac_address - Fix for Mac addr problem on Alpha platforms * @sp: Pointer to device specifc structure - * Description : + * Description : * New procedure to clear mac address reading problems on Alpha platforms * */ -static void fix_mac_address(nic_t * sp) +void fix_mac_address(nic_t * sp) { XENA_dev_config_t __iomem *bar0 = sp->bar0; u64 val64; @@ -1303,20 +1316,21 @@ static void fix_mac_address(nic_t * sp) while (fix_mac[i] != END_SIGN) { writeq(fix_mac[i++], &bar0->gpio_control); + udelay(10); val64 = readq(&bar0->gpio_control); } } /** - * start_nic - Turns the device on + * start_nic - Turns the device on * @nic : device private variable. - * Description: - * This function actually turns the device on. Before this function is - * called,all Registers are configured from their reset states - * and shared memory is allocated but the NIC is still quiescent. On + * Description: + * This function actually turns the device on. Before this function is + * called,all Registers are configured from their reset states + * and shared memory is allocated but the NIC is still quiescent. On * calling this function, the device interrupts are cleared and the NIC is * literally switched on by writing into the adapter control register. - * Return Value: + * Return Value: * SUCCESS on success and -1 on failure. */ @@ -1325,8 +1339,8 @@ static int start_nic(struct s2io_nic *nic) XENA_dev_config_t __iomem *bar0 = nic->bar0; struct net_device *dev = nic->dev; register u64 val64 = 0; - u16 interruptible, i; - u16 subid; + u16 interruptible; + u16 subid, i; mac_info_t *mac_control; struct config_param *config; @@ -1335,7 +1349,7 @@ static int start_nic(struct s2io_nic *nic) /* PRC Initialization and configuration */ for (i = 0; i < config->rx_ring_num; i++) { - writeq((u64) nic->rx_blocks[i][0].block_dma_addr, + writeq((u64) mac_control->rings[i].rx_blocks[0].block_dma_addr, &bar0->prc_rxd0_n[i]); val64 = readq(&bar0->prc_ctrl_n[i]); @@ -1354,7 +1368,7 @@ static int start_nic(struct s2io_nic *nic) writeq(val64, &bar0->rx_pa_cfg); #endif - /* + /* * Enabling MC-RLDRAM. After enabling the device, we timeout * for around 100ms, which is approximately the time required * for the device to be ready for operation. @@ -1364,27 +1378,27 @@ static int start_nic(struct s2io_nic *nic) SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF); val64 = readq(&bar0->mc_rldram_mrs); - msleep(100); /* Delay by around 100 ms. */ + msleep(100); /* Delay by around 100 ms. */ /* Enabling ECC Protection. */ val64 = readq(&bar0->adapter_control); val64 &= ~ADAPTER_ECC_EN; writeq(val64, &bar0->adapter_control); - /* - * Clearing any possible Link state change interrupts that + /* + * Clearing any possible Link state change interrupts that * could have popped up just before Enabling the card. */ val64 = readq(&bar0->mac_rmac_err_reg); if (val64) writeq(val64, &bar0->mac_rmac_err_reg); - /* - * Verify if the device is ready to be enabled, if so enable + /* + * Verify if the device is ready to be enabled, if so enable * it. */ val64 = readq(&bar0->adapter_status); - if (!verify_xena_quiescence(val64, nic->device_enabled_once)) { + if (!verify_xena_quiescence(nic, val64, nic->device_enabled_once)) { DBG_PRINT(ERR_DBG, "%s: device is not ready, ", dev->name); DBG_PRINT(ERR_DBG, "Adapter status reads: 0x%llx\n", (unsigned long long) val64); @@ -1396,12 +1410,12 @@ static int start_nic(struct s2io_nic *nic) RX_MAC_INTR; en_dis_able_nic_intrs(nic, interruptible, ENABLE_INTRS); - /* + /* * With some switches, link might be already up at this point. - * Because of this weird behavior, when we enable laser, - * we may not get link. We need to handle this. We cannot - * figure out which switch is misbehaving. So we are forced to - * make a global change. + * Because of this weird behavior, when we enable laser, + * we may not get link. We need to handle this. We cannot + * figure out which switch is misbehaving. So we are forced to + * make a global change. */ /* Enabling Laser. */ @@ -1416,17 +1430,17 @@ static int start_nic(struct s2io_nic *nic) val64 |= 0x0000800000000000ULL; writeq(val64, &bar0->gpio_control); val64 = 0x0411040400000000ULL; - writeq(val64, (void __iomem *) bar0 + 0x2700); + writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700)); } - /* - * Don't see link state interrupts on certain switches, so + /* + * Don't see link state interrupts on certain switches, so * directly scheduling a link state task from here. */ schedule_work(&nic->set_link_task); - /* - * Here we are performing soft reset on XGXS to + /* + * Here we are performing soft reset on XGXS to * force link down. Since link is already up, we will get * link state change interrupt after this reset */ @@ -1443,12 +1457,12 @@ static int start_nic(struct s2io_nic *nic) return SUCCESS; } -/** - * free_tx_buffers - Free all queued Tx buffers +/** + * free_tx_buffers - Free all queued Tx buffers * @nic : device private variable. - * Description: + * Description: * Free all queued Tx buffers. - * Return Value: void + * Return Value: void */ static void free_tx_buffers(struct s2io_nic *nic) @@ -1466,7 +1480,7 @@ static void free_tx_buffers(struct s2io_nic *nic) for (i = 0; i < config->tx_fifo_num; i++) { for (j = 0; j < config->tx_cfg[i].fifo_len - 1; j++) { - txdp = (TxD_t *) nic->list_info[i][j]. + txdp = (TxD_t *) mac_control->fifos[i].list_info[j]. list_virt_addr; skb = (struct sk_buff *) ((unsigned long) txdp-> @@ -1482,16 +1496,16 @@ static void free_tx_buffers(struct s2io_nic *nic) DBG_PRINT(INTR_DBG, "%s:forcibly freeing %d skbs on FIFO%d\n", dev->name, cnt, i); - mac_control->tx_curr_get_info[i].offset = 0; - mac_control->tx_curr_put_info[i].offset = 0; + mac_control->fifos[i].tx_curr_get_info.offset = 0; + mac_control->fifos[i].tx_curr_put_info.offset = 0; } } -/** - * stop_nic - To stop the nic +/** + * stop_nic - To stop the nic * @nic ; device private variable. - * Description: - * This function does exactly the opposite of what the start_nic() + * Description: + * This function does exactly the opposite of what the start_nic() * function does. This function is called to stop the device. * Return Value: * void. @@ -1521,11 +1535,11 @@ static void stop_nic(struct s2io_nic *nic) } } -/** - * fill_rx_buffers - Allocates the Rx side skbs +/** + * fill_rx_buffers - Allocates the Rx side skbs * @nic: device private variable - * @ring_no: ring number - * Description: + * @ring_no: ring number + * Description: * The function allocates Rx side skbs and puts the physical * address of these buffers into the RxD buffer pointers, so that the NIC * can DMA the received frame into these locations. @@ -1533,8 +1547,8 @@ static void stop_nic(struct s2io_nic *nic) * 1. single buffer, * 2. three buffer and * 3. Five buffer modes. - * Each mode defines how many fragments the received frame will be split - * up into by the NIC. The frame is split into L3 header, L4 Header, + * Each mode defines how many fragments the received frame will be split + * up into by the NIC. The frame is split into L3 header, L4 Header, * L4 payload in three buffer mode and in 5 buffer mode, L4 payload itself * is split into 3 fragments. As of now only single buffer mode is * supported. @@ -1542,7 +1556,7 @@ static void stop_nic(struct s2io_nic *nic) * SUCCESS on success or an appropriate -ve value on failure. */ -static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) +int fill_rx_buffers(struct s2io_nic *nic, int ring_no) { struct net_device *dev = nic->dev; struct sk_buff *skb; @@ -1550,14 +1564,13 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) int off, off1, size, block_no, block_no1; int offset, offset1; u32 alloc_tab = 0; - u32 alloc_cnt = nic->pkt_cnt[ring_no] - - atomic_read(&nic->rx_bufs_left[ring_no]); + u32 alloc_cnt; mac_info_t *mac_control; struct config_param *config; #ifdef CONFIG_2BUFF_MODE RxD_t *rxdpnext; int nextblk; - unsigned long tmp; + u64 tmp; buffAdd_t *ba; dma_addr_t rxdpphys; #endif @@ -1567,17 +1580,18 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) mac_control = &nic->mac_control; config = &nic->config; - + alloc_cnt = mac_control->rings[ring_no].pkt_cnt - + atomic_read(&nic->rx_bufs_left[ring_no]); size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE + HEADER_802_2_SIZE + HEADER_SNAP_SIZE; while (alloc_tab < alloc_cnt) { - block_no = mac_control->rx_curr_put_info[ring_no]. + block_no = mac_control->rings[ring_no].rx_curr_put_info. block_index; - block_no1 = mac_control->rx_curr_get_info[ring_no]. + block_no1 = mac_control->rings[ring_no].rx_curr_get_info. block_index; - off = mac_control->rx_curr_put_info[ring_no].offset; - off1 = mac_control->rx_curr_get_info[ring_no].offset; + off = mac_control->rings[ring_no].rx_curr_put_info.offset; + off1 = mac_control->rings[ring_no].rx_curr_get_info.offset; #ifndef CONFIG_2BUFF_MODE offset = block_no * (MAX_RXDS_PER_BLOCK + 1) + off; offset1 = block_no1 * (MAX_RXDS_PER_BLOCK + 1) + off1; @@ -1586,7 +1600,7 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) offset1 = block_no1 * (MAX_RXDS_PER_BLOCK) + off1; #endif - rxdp = nic->rx_blocks[ring_no][block_no]. + rxdp = mac_control->rings[ring_no].rx_blocks[block_no]. block_virt_addr + off; if ((offset == offset1) && (rxdp->Host_Control)) { DBG_PRINT(INTR_DBG, "%s: Get and Put", dev->name); @@ -1595,15 +1609,15 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) } #ifndef CONFIG_2BUFF_MODE if (rxdp->Control_1 == END_OF_BLOCK) { - mac_control->rx_curr_put_info[ring_no]. + mac_control->rings[ring_no].rx_curr_put_info. block_index++; - mac_control->rx_curr_put_info[ring_no]. - block_index %= nic->block_count[ring_no]; - block_no = mac_control->rx_curr_put_info - [ring_no].block_index; + mac_control->rings[ring_no].rx_curr_put_info. + block_index %= mac_control->rings[ring_no].block_count; + block_no = mac_control->rings[ring_no].rx_curr_put_info. + block_index; off++; off %= (MAX_RXDS_PER_BLOCK + 1); - mac_control->rx_curr_put_info[ring_no].offset = + mac_control->rings[ring_no].rx_curr_put_info.offset = off; rxdp = (RxD_t *) ((unsigned long) rxdp->Control_2); DBG_PRINT(INTR_DBG, "%s: Next block at: %p\n", @@ -1611,30 +1625,30 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) } #ifndef CONFIG_S2IO_NAPI spin_lock_irqsave(&nic->put_lock, flags); - nic->put_pos[ring_no] = + mac_control->rings[ring_no].put_pos = (block_no * (MAX_RXDS_PER_BLOCK + 1)) + off; spin_unlock_irqrestore(&nic->put_lock, flags); #endif #else if (rxdp->Host_Control == END_OF_BLOCK) { - mac_control->rx_curr_put_info[ring_no]. + mac_control->rings[ring_no].rx_curr_put_info. block_index++; - mac_control->rx_curr_put_info[ring_no]. - block_index %= nic->block_count[ring_no]; - block_no = mac_control->rx_curr_put_info - [ring_no].block_index; + mac_control->rings[ring_no].rx_curr_put_info.block_index + %= mac_control->rings[ring_no].block_count; + block_no = mac_control->rings[ring_no].rx_curr_put_info + .block_index; off = 0; DBG_PRINT(INTR_DBG, "%s: block%d at: 0x%llx\n", dev->name, block_no, (unsigned long long) rxdp->Control_1); - mac_control->rx_curr_put_info[ring_no].offset = + mac_control->rings[ring_no].rx_curr_put_info.offset = off; - rxdp = nic->rx_blocks[ring_no][block_no]. + rxdp = mac_control->rings[ring_no].rx_blocks[block_no]. block_virt_addr; } #ifndef CONFIG_S2IO_NAPI spin_lock_irqsave(&nic->put_lock, flags); - nic->put_pos[ring_no] = (block_no * + mac_control->rings[ring_no].put_pos = (block_no * (MAX_RXDS_PER_BLOCK + 1)) + off; spin_unlock_irqrestore(&nic->put_lock, flags); #endif @@ -1646,27 +1660,27 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) if (rxdp->Control_2 & BIT(0)) #endif { - mac_control->rx_curr_put_info[ring_no]. + mac_control->rings[ring_no].rx_curr_put_info. offset = off; goto end; } #ifdef CONFIG_2BUFF_MODE - /* - * RxDs Spanning cache lines will be replenished only - * if the succeeding RxD is also owned by Host. It - * will always be the ((8*i)+3) and ((8*i)+6) - * descriptors for the 48 byte descriptor. The offending + /* + * RxDs Spanning cache lines will be replenished only + * if the succeeding RxD is also owned by Host. It + * will always be the ((8*i)+3) and ((8*i)+6) + * descriptors for the 48 byte descriptor. The offending * decsriptor is of-course the 3rd descriptor. */ - rxdpphys = nic->rx_blocks[ring_no][block_no]. + rxdpphys = mac_control->rings[ring_no].rx_blocks[block_no]. block_dma_addr + (off * sizeof(RxD_t)); if (((u64) (rxdpphys)) % 128 > 80) { - rxdpnext = nic->rx_blocks[ring_no][block_no]. + rxdpnext = mac_control->rings[ring_no].rx_blocks[block_no]. block_virt_addr + (off + 1); if (rxdpnext->Host_Control == END_OF_BLOCK) { nextblk = (block_no + 1) % - (nic->block_count[ring_no]); - rxdpnext = nic->rx_blocks[ring_no] + (mac_control->rings[ring_no].block_count); + rxdpnext = mac_control->rings[ring_no].rx_blocks [nextblk].block_virt_addr; } if (rxdpnext->Control_2 & BIT(0)) @@ -1695,9 +1709,9 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) rxdp->Control_1 |= RXD_OWN_XENA; off++; off %= (MAX_RXDS_PER_BLOCK + 1); - mac_control->rx_curr_put_info[ring_no].offset = off; + mac_control->rings[ring_no].rx_curr_put_info.offset = off; #else - ba = &nic->ba[ring_no][block_no][off]; + ba = &mac_control->rings[ring_no].ba[block_no][off]; skb_reserve(skb, BUF0_LEN); tmp = ((unsigned long) skb->data & ALIGN_SIZE); if (tmp) @@ -1721,8 +1735,9 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) rxdp->Host_Control = (u64) ((unsigned long) (skb)); rxdp->Control_1 |= RXD_OWN_XENA; off++; - mac_control->rx_curr_put_info[ring_no].offset = off; + mac_control->rings[ring_no].rx_curr_put_info.offset = off; #endif + atomic_inc(&nic->rx_bufs_left[ring_no]); alloc_tab++; } @@ -1732,9 +1747,9 @@ static int fill_rx_buffers(struct s2io_nic *nic, int ring_no) } /** - * free_rx_buffers - Frees all Rx buffers + * free_rx_buffers - Frees all Rx buffers * @sp: device private variable. - * Description: + * Description: * This function will free all Rx buffers allocated by host. * Return Value: * NONE. @@ -1758,7 +1773,8 @@ static void free_rx_buffers(struct s2io_nic *sp) for (i = 0; i < config->rx_ring_num; i++) { for (j = 0, blk = 0; j < config->rx_cfg[i].num_rxd; j++) { off = j % (MAX_RXDS_PER_BLOCK + 1); - rxdp = sp->rx_blocks[i][blk].block_virt_addr + off; + rxdp = mac_control->rings[i].rx_blocks[blk]. + block_virt_addr + off; #ifndef CONFIG_2BUFF_MODE if (rxdp->Control_1 == END_OF_BLOCK) { @@ -1793,7 +1809,7 @@ static void free_rx_buffers(struct s2io_nic *sp) HEADER_SNAP_SIZE, PCI_DMA_FROMDEVICE); #else - ba = &sp->ba[i][blk][off]; + ba = &mac_control->rings[i].ba[blk][off]; pci_unmap_single(sp->pdev, (dma_addr_t) rxdp->Buffer0_ptr, BUF0_LEN, @@ -1813,10 +1829,10 @@ static void free_rx_buffers(struct s2io_nic *sp) } memset(rxdp, 0, sizeof(RxD_t)); } - mac_control->rx_curr_put_info[i].block_index = 0; - mac_control->rx_curr_get_info[i].block_index = 0; - mac_control->rx_curr_put_info[i].offset = 0; - mac_control->rx_curr_get_info[i].offset = 0; + mac_control->rings[i].rx_curr_put_info.block_index = 0; + mac_control->rings[i].rx_curr_get_info.block_index = 0; + mac_control->rings[i].rx_curr_put_info.offset = 0; + mac_control->rings[i].rx_curr_get_info.offset = 0; atomic_set(&sp->rx_bufs_left[i], 0); DBG_PRINT(INIT_DBG, "%s:Freed 0x%x Rx Buffers on ring%d\n", dev->name, buf_cnt, i); @@ -1826,7 +1842,7 @@ static void free_rx_buffers(struct s2io_nic *sp) /** * s2io_poll - Rx interrupt handler for NAPI support * @dev : pointer to the device structure. - * @budget : The number of packets that were budgeted to be processed + * @budget : The number of packets that were budgeted to be processed * during one pass through the 'Poll" function. * Description: * Comes into picture only if NAPI support has been incorporated. It does @@ -1836,160 +1852,35 @@ static void free_rx_buffers(struct s2io_nic *sp) * 0 on success and 1 if there are No Rx packets to be processed. */ -#ifdef CONFIG_S2IO_NAPI +#if defined(CONFIG_S2IO_NAPI) static int s2io_poll(struct net_device *dev, int *budget) { nic_t *nic = dev->priv; - XENA_dev_config_t __iomem *bar0 = nic->bar0; - int pkts_to_process = *budget, pkt_cnt = 0; - register u64 val64 = 0; - rx_curr_get_info_t get_info, put_info; - int i, get_block, put_block, get_offset, put_offset, ring_bufs; -#ifndef CONFIG_2BUFF_MODE - u16 val16, cksum; -#endif - struct sk_buff *skb; - RxD_t *rxdp; + int pkt_cnt = 0, org_pkts_to_process; mac_info_t *mac_control; struct config_param *config; -#ifdef CONFIG_2BUFF_MODE - buffAdd_t *ba; -#endif + XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0; + u64 val64; + int i; mac_control = &nic->mac_control; config = &nic->config; - if (pkts_to_process > dev->quota) - pkts_to_process = dev->quota; + nic->pkts_to_process = *budget; + if (nic->pkts_to_process > dev->quota) + nic->pkts_to_process = dev->quota; + org_pkts_to_process = nic->pkts_to_process; val64 = readq(&bar0->rx_traffic_int); writeq(val64, &bar0->rx_traffic_int); for (i = 0; i < config->rx_ring_num; i++) { - get_info = mac_control->rx_curr_get_info[i]; - get_block = get_info.block_index; - put_info = mac_control->rx_curr_put_info[i]; - put_block = put_info.block_index; - ring_bufs = config->rx_cfg[i].num_rxd; - rxdp = nic->rx_blocks[i][get_block].block_virt_addr + - get_info.offset; -#ifndef CONFIG_2BUFF_MODE - get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) + - get_info.offset; - put_offset = (put_block * (MAX_RXDS_PER_BLOCK + 1)) + - put_info.offset; - while ((!(rxdp->Control_1 & RXD_OWN_XENA)) && - (((get_offset + 1) % ring_bufs) != put_offset)) { - if (--pkts_to_process < 0) { - goto no_rx; - } - if (rxdp->Control_1 == END_OF_BLOCK) { - rxdp = - (RxD_t *) ((unsigned long) rxdp-> - Control_2); - get_info.offset++; - get_info.offset %= - (MAX_RXDS_PER_BLOCK + 1); - get_block++; - get_block %= nic->block_count[i]; - mac_control->rx_curr_get_info[i]. - offset = get_info.offset; - mac_control->rx_curr_get_info[i]. - block_index = get_block; - continue; - } - get_offset = - (get_block * (MAX_RXDS_PER_BLOCK + 1)) + - get_info.offset; - skb = - (struct sk_buff *) ((unsigned long) rxdp-> - Host_Control); - if (skb == NULL) { - DBG_PRINT(ERR_DBG, "%s: The skb is ", - dev->name); - DBG_PRINT(ERR_DBG, "Null in Rx Intr\n"); - goto no_rx; - } - val64 = RXD_GET_BUFFER0_SIZE(rxdp->Control_2); - val16 = (u16) (val64 >> 48); - cksum = RXD_GET_L4_CKSUM(rxdp->Control_1); - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer0_ptr, - dev->mtu + - HEADER_ETHERNET_II_802_3_SIZE + - HEADER_802_2_SIZE + - HEADER_SNAP_SIZE, - PCI_DMA_FROMDEVICE); - rx_osm_handler(nic, val16, rxdp, i); - pkt_cnt++; - get_info.offset++; - get_info.offset %= (MAX_RXDS_PER_BLOCK + 1); - rxdp = - nic->rx_blocks[i][get_block].block_virt_addr + - get_info.offset; - mac_control->rx_curr_get_info[i].offset = - get_info.offset; + rx_intr_handler(&mac_control->rings[i]); + pkt_cnt = org_pkts_to_process - nic->pkts_to_process; + if (!nic->pkts_to_process) { + /* Quota for the current iteration has been met */ + goto no_rx; } -#else - get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) + - get_info.offset; - put_offset = (put_block * (MAX_RXDS_PER_BLOCK + 1)) + - put_info.offset; - while (((!(rxdp->Control_1 & RXD_OWN_XENA)) && - !(rxdp->Control_2 & BIT(0))) && - (((get_offset + 1) % ring_bufs) != put_offset)) { - if (--pkts_to_process < 0) { - goto no_rx; - } - skb = (struct sk_buff *) ((unsigned long) - rxdp->Host_Control); - if (skb == NULL) { - DBG_PRINT(ERR_DBG, "%s: The skb is ", - dev->name); - DBG_PRINT(ERR_DBG, "Null in Rx Intr\n"); - goto no_rx; - } - - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer0_ptr, - BUF0_LEN, PCI_DMA_FROMDEVICE); - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer1_ptr, - BUF1_LEN, PCI_DMA_FROMDEVICE); - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer2_ptr, - dev->mtu + BUF0_LEN + 4, - PCI_DMA_FROMDEVICE); - ba = &nic->ba[i][get_block][get_info.offset]; - - rx_osm_handler(nic, rxdp, i, ba); - - get_info.offset++; - mac_control->rx_curr_get_info[i].offset = - get_info.offset; - rxdp = - nic->rx_blocks[i][get_block].block_virt_addr + - get_info.offset; - - if (get_info.offset && - (!(get_info.offset % MAX_RXDS_PER_BLOCK))) { - get_info.offset = 0; - mac_control->rx_curr_get_info[i]. - offset = get_info.offset; - get_block++; - get_block %= nic->block_count[i]; - mac_control->rx_curr_get_info[i]. - block_index = get_block; - rxdp = - nic->rx_blocks[i][get_block]. - block_virt_addr; - } - get_offset = - (get_block * (MAX_RXDS_PER_BLOCK + 1)) + - get_info.offset; - pkt_cnt++; - } -#endif } if (!pkt_cnt) pkt_cnt = 1; @@ -2009,7 +1900,7 @@ static int s2io_poll(struct net_device *dev, int *budget) en_dis_able_nic_intrs(nic, RX_TRAFFIC_INTR, ENABLE_INTRS); return 0; - no_rx: +no_rx: dev->quota -= pkt_cnt; *budget -= pkt_cnt; @@ -2022,277 +1913,213 @@ static int s2io_poll(struct net_device *dev, int *budget) } return 1; } -#else -/** +#endif + +/** * rx_intr_handler - Rx interrupt handler * @nic: device private variable. - * Description: - * If the interrupt is because of a received frame or if the + * Description: + * If the interrupt is because of a received frame or if the * receive ring contains fresh as yet un-processed frames,this function is - * called. It picks out the RxD at which place the last Rx processing had - * stopped and sends the skb to the OSM's Rx handler and then increments + * called. It picks out the RxD at which place the last Rx processing had + * stopped and sends the skb to the OSM's Rx handler and then increments * the offset. * Return Value: * NONE. */ - -static void rx_intr_handler(struct s2io_nic *nic) +static void rx_intr_handler(ring_info_t *ring_data) { + nic_t *nic = ring_data->nic; struct net_device *dev = (struct net_device *) nic->dev; - XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0; + XENA_dev_config_t __iomem *bar0 = nic->bar0; + int get_block, get_offset, put_block, put_offset, ring_bufs; rx_curr_get_info_t get_info, put_info; RxD_t *rxdp; struct sk_buff *skb; -#ifndef CONFIG_2BUFF_MODE - u16 val16, cksum; -#endif - register u64 val64 = 0; - int get_block, get_offset, put_block, put_offset, ring_bufs; - int i, pkt_cnt = 0; - mac_info_t *mac_control; - struct config_param *config; -#ifdef CONFIG_2BUFF_MODE - buffAdd_t *ba; +#ifndef CONFIG_S2IO_NAPI + int pkt_cnt = 0; #endif + register u64 val64; - mac_control = &nic->mac_control; - config = &nic->config; - - /* - * rx_traffic_int reg is an R1 register, hence we read and write back - * the samevalue in the register to clear it. + /* + * rx_traffic_int reg is an R1 register, hence we read and write + * back the same value in the register to clear it */ - val64 = readq(&bar0->rx_traffic_int); - writeq(val64, &bar0->rx_traffic_int); + val64 = readq(&bar0->tx_traffic_int); + writeq(val64, &bar0->tx_traffic_int); - for (i = 0; i < config->rx_ring_num; i++) { - get_info = mac_control->rx_curr_get_info[i]; - get_block = get_info.block_index; - put_info = mac_control->rx_curr_put_info[i]; - put_block = put_info.block_index; - ring_bufs = config->rx_cfg[i].num_rxd; - rxdp = nic->rx_blocks[i][get_block].block_virt_addr + + get_info = ring_data->rx_curr_get_info; + get_block = get_info.block_index; + put_info = ring_data->rx_curr_put_info; + put_block = put_info.block_index; + ring_bufs = get_info.ring_len+1; + rxdp = ring_data->rx_blocks[get_block].block_virt_addr + get_info.offset; -#ifndef CONFIG_2BUFF_MODE - get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) + - get_info.offset; - spin_lock(&nic->put_lock); - put_offset = nic->put_pos[i]; - spin_unlock(&nic->put_lock); - while ((!(rxdp->Control_1 & RXD_OWN_XENA)) && - (((get_offset + 1) % ring_bufs) != put_offset)) { - if (rxdp->Control_1 == END_OF_BLOCK) { - rxdp = (RxD_t *) ((unsigned long) - rxdp->Control_2); - get_info.offset++; - get_info.offset %= - (MAX_RXDS_PER_BLOCK + 1); - get_block++; - get_block %= nic->block_count[i]; - mac_control->rx_curr_get_info[i]. - offset = get_info.offset; - mac_control->rx_curr_get_info[i]. - block_index = get_block; - continue; - } - get_offset = - (get_block * (MAX_RXDS_PER_BLOCK + 1)) + - get_info.offset; - skb = (struct sk_buff *) ((unsigned long) - rxdp->Host_Control); - if (skb == NULL) { - DBG_PRINT(ERR_DBG, "%s: The skb is ", - dev->name); - DBG_PRINT(ERR_DBG, "Null in Rx Intr\n"); - return; - } - val64 = RXD_GET_BUFFER0_SIZE(rxdp->Control_2); - val16 = (u16) (val64 >> 48); - cksum = RXD_GET_L4_CKSUM(rxdp->Control_1); - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer0_ptr, - dev->mtu + - HEADER_ETHERNET_II_802_3_SIZE + - HEADER_802_2_SIZE + - HEADER_SNAP_SIZE, - PCI_DMA_FROMDEVICE); - rx_osm_handler(nic, val16, rxdp, i); - get_info.offset++; - get_info.offset %= (MAX_RXDS_PER_BLOCK + 1); - rxdp = - nic->rx_blocks[i][get_block].block_virt_addr + - get_info.offset; - mac_control->rx_curr_get_info[i].offset = - get_info.offset; - pkt_cnt++; - if ((indicate_max_pkts) - && (pkt_cnt > indicate_max_pkts)) - break; + get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) + + get_info.offset; +#ifndef CONFIG_S2IO_NAPI + spin_lock(&nic->put_lock); + put_offset = ring_data->put_pos; + spin_unlock(&nic->put_lock); +#else + put_offset = (put_block * (MAX_RXDS_PER_BLOCK + 1)) + + put_info.offset; +#endif + while ((!(rxdp->Control_1 & RXD_OWN_XENA)) && +#ifdef CONFIG_2BUFF_MODE + (!rxdp->Control_2 & BIT(0)) && +#endif + (((get_offset + 1) % ring_bufs) != put_offset)) { + skb = (struct sk_buff *) ((unsigned long)rxdp->Host_Control); + if (skb == NULL) { + DBG_PRINT(ERR_DBG, "%s: The skb is ", + dev->name); + DBG_PRINT(ERR_DBG, "Null in Rx Intr\n"); + return; } +#ifndef CONFIG_2BUFF_MODE + pci_unmap_single(nic->pdev, (dma_addr_t) + rxdp->Buffer0_ptr, + dev->mtu + + HEADER_ETHERNET_II_802_3_SIZE + + HEADER_802_2_SIZE + + HEADER_SNAP_SIZE, + PCI_DMA_FROMDEVICE); #else - get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) + + pci_unmap_single(nic->pdev, (dma_addr_t) + rxdp->Buffer0_ptr, + BUF0_LEN, PCI_DMA_FROMDEVICE); + pci_unmap_single(nic->pdev, (dma_addr_t) + rxdp->Buffer1_ptr, + BUF1_LEN, PCI_DMA_FROMDEVICE); + pci_unmap_single(nic->pdev, (dma_addr_t) + rxdp->Buffer2_ptr, + dev->mtu + BUF0_LEN + 4, + PCI_DMA_FROMDEVICE); +#endif + rx_osm_handler(ring_data, rxdp); + get_info.offset++; + ring_data->rx_curr_get_info.offset = get_info.offset; - spin_lock(&nic->put_lock); - put_offset = nic->put_pos[i]; - spin_unlock(&nic->put_lock); - while (((!(rxdp->Control_1 & RXD_OWN_XENA)) && - !(rxdp->Control_2 & BIT(0))) && - (((get_offset + 1) % ring_bufs) != put_offset)) { - skb = (struct sk_buff *) ((unsigned long) - rxdp->Host_Control); - if (skb == NULL) { - DBG_PRINT(ERR_DBG, "%s: The skb is ", - dev->name); - DBG_PRINT(ERR_DBG, "Null in Rx Intr\n"); - return; - } - - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer0_ptr, - BUF0_LEN, PCI_DMA_FROMDEVICE); - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer1_ptr, - BUF1_LEN, PCI_DMA_FROMDEVICE); - pci_unmap_single(nic->pdev, (dma_addr_t) - rxdp->Buffer2_ptr, - dev->mtu + BUF0_LEN + 4, - PCI_DMA_FROMDEVICE); - ba = &nic->ba[i][get_block][get_info.offset]; - - rx_osm_handler(nic, rxdp, i, ba); - - get_info.offset++; - mac_control->rx_curr_get_info[i].offset = - get_info.offset; - rxdp = - nic->rx_blocks[i][get_block].block_virt_addr + - get_info.offset; + rxdp = ring_data->rx_blocks[get_block].block_virt_addr + + get_info.offset; + if (get_info.offset && + (!(get_info.offset % MAX_RXDS_PER_BLOCK))) { + get_info.offset = 0; + ring_data->rx_curr_get_info.offset + = get_info.offset; + get_block++; + get_block %= ring_data->block_count; + ring_data->rx_curr_get_info.block_index + = get_block; + rxdp = ring_data->rx_blocks[get_block].block_virt_addr; + } - if (get_info.offset && - (!(get_info.offset % MAX_RXDS_PER_BLOCK))) { - get_info.offset = 0; - mac_control->rx_curr_get_info[i]. - offset = get_info.offset; - get_block++; - get_block %= nic->block_count[i]; - mac_control->rx_curr_get_info[i]. - block_index = get_block; - rxdp = - nic->rx_blocks[i][get_block]. - block_virt_addr; - } - get_offset = - (get_block * (MAX_RXDS_PER_BLOCK + 1)) + + get_offset = (get_block * (MAX_RXDS_PER_BLOCK + 1)) + get_info.offset; - pkt_cnt++; - if ((indicate_max_pkts) - && (pkt_cnt > indicate_max_pkts)) - break; - } -#endif +#ifdef CONFIG_S2IO_NAPI + nic->pkts_to_process -= 1; + if (!nic->pkts_to_process) + break; +#else + pkt_cnt++; if ((indicate_max_pkts) && (pkt_cnt > indicate_max_pkts)) break; +#endif } } -#endif -/** + +/** * tx_intr_handler - Transmit interrupt handler * @nic : device private variable - * Description: - * If an interrupt was raised to indicate DMA complete of the - * Tx packet, this function is called. It identifies the last TxD - * whose buffer was freed and frees all skbs whose data have already + * Description: + * If an interrupt was raised to indicate DMA complete of the + * Tx packet, this function is called. It identifies the last TxD + * whose buffer was freed and frees all skbs whose data have already * DMA'ed into the NICs internal memory. * Return Value: * NONE */ -static void tx_intr_handler(struct s2io_nic *nic) +static void tx_intr_handler(fifo_info_t *fifo_data) { + nic_t *nic = fifo_data->nic; XENA_dev_config_t __iomem *bar0 = nic->bar0; struct net_device *dev = (struct net_device *) nic->dev; tx_curr_get_info_t get_info, put_info; struct sk_buff *skb; TxD_t *txdlp; - register u64 val64 = 0; - int i; u16 j, frg_cnt; - mac_info_t *mac_control; - struct config_param *config; - - mac_control = &nic->mac_control; - config = &nic->config; + register u64 val64 = 0; - /* - * tx_traffic_int reg is an R1 register, hence we read and write - * back the samevalue in the register to clear it. + /* + * tx_traffic_int reg is an R1 register, hence we read and write + * back the same value in the register to clear it */ val64 = readq(&bar0->tx_traffic_int); writeq(val64, &bar0->tx_traffic_int); - for (i = 0; i < config->tx_fifo_num; i++) { - get_info = mac_control->tx_curr_get_info[i]; - put_info = mac_control->tx_curr_put_info[i]; - txdlp = (TxD_t *) nic->list_info[i][get_info.offset]. - list_virt_addr; - while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) && - (get_info.offset != put_info.offset) && - (txdlp->Host_Control)) { - /* Check for TxD errors */ - if (txdlp->Control_1 & TXD_T_CODE) { - unsigned long long err; - err = txdlp->Control_1 & TXD_T_CODE; - DBG_PRINT(ERR_DBG, "***TxD error %llx\n", - err); - } + get_info = fifo_data->tx_curr_get_info; + put_info = fifo_data->tx_curr_put_info; + txdlp = (TxD_t *) fifo_data->list_info[get_info.offset]. + list_virt_addr; + while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) && + (get_info.offset != put_info.offset) && + (txdlp->Host_Control)) { + /* Check for TxD errors */ + if (txdlp->Control_1 & TXD_T_CODE) { + unsigned long long err; + err = txdlp->Control_1 & TXD_T_CODE; + DBG_PRINT(ERR_DBG, "***TxD error %llx\n", + err); + } - skb = (struct sk_buff *) ((unsigned long) - txdlp->Host_Control); - if (skb == NULL) { - DBG_PRINT(ERR_DBG, "%s: Null skb ", - dev->name); - DBG_PRINT(ERR_DBG, "in Tx Free Intr\n"); - return; - } - nic->tx_pkt_count++; - - frg_cnt = skb_shinfo(skb)->nr_frags; - - /* For unfragmented skb */ - pci_unmap_single(nic->pdev, (dma_addr_t) - txdlp->Buffer_Pointer, - skb->len - skb->data_len, - PCI_DMA_TODEVICE); - if (frg_cnt) { - TxD_t *temp = txdlp; - txdlp++; - for (j = 0; j < frg_cnt; j++, txdlp++) { - skb_frag_t *frag = - &skb_shinfo(skb)->frags[j]; - pci_unmap_page(nic->pdev, - (dma_addr_t) - txdlp-> - Buffer_Pointer, - frag->size, - PCI_DMA_TODEVICE); - } - txdlp = temp; + skb = (struct sk_buff *) ((unsigned long) + txdlp->Host_Control); + if (skb == NULL) { + DBG_PRINT(ERR_DBG, "%s: Null skb ", + __FUNCTION__); + DBG_PRINT(ERR_DBG, "in Tx Free Intr\n"); + return; + } + + frg_cnt = skb_shinfo(skb)->nr_frags; + nic->tx_pkt_count++; + + pci_unmap_single(nic->pdev, (dma_addr_t) + txdlp->Buffer_Pointer, + skb->len - skb->data_len, + PCI_DMA_TODEVICE); + if (frg_cnt) { + TxD_t *temp; + temp = txdlp; + txdlp++; + for (j = 0; j < frg_cnt; j++, txdlp++) { + skb_frag_t *frag = + &skb_shinfo(skb)->frags[j]; + pci_unmap_page(nic->pdev, + (dma_addr_t) + txdlp-> + Buffer_Pointer, + frag->size, + PCI_DMA_TODEVICE); } - memset(txdlp, 0, - (sizeof(TxD_t) * config->max_txds)); - - /* Updating the statistics block */ - nic->stats.tx_packets++; - nic->stats.tx_bytes += skb->len; - dev_kfree_skb_irq(skb); - - get_info.offset++; - get_info.offset %= get_info.fifo_len + 1; - txdlp = (TxD_t *) nic->list_info[i] - [get_info.offset].list_virt_addr; - mac_control->tx_curr_get_info[i].offset = - get_info.offset; + txdlp = temp; } + memset(txdlp, 0, + (sizeof(TxD_t) * fifo_data->max_txds)); + + /* Updating the statistics block */ + nic->stats.tx_packets++; + nic->stats.tx_bytes += skb->len; + dev_kfree_skb_irq(skb); + + get_info.offset++; + get_info.offset %= get_info.fifo_len + 1; + txdlp = (TxD_t *) fifo_data->list_info + [get_info.offset].list_virt_addr; + fifo_data->tx_curr_get_info.offset = + get_info.offset; } spin_lock(&nic->tx_lock); @@ -2301,13 +2128,13 @@ static void tx_intr_handler(struct s2io_nic *nic) spin_unlock(&nic->tx_lock); } -/** +/** * alarm_intr_handler - Alarm Interrrupt handler * @nic: device private variable - * Description: If the interrupt was neither because of Rx packet or Tx + * Description: If the interrupt was neither because of Rx packet or Tx * complete, this function is called. If the interrupt was to indicate - * a loss of link, the OSM link status handler is invoked for any other - * alarm interrupt the block that raised the interrupt is displayed + * a loss of link, the OSM link status handler is invoked for any other + * alarm interrupt the block that raised the interrupt is displayed * and a H/W reset is issued. * Return Value: * NONE @@ -2338,7 +2165,7 @@ static void alarm_intr_handler(struct s2io_nic *nic) /* * Also as mentioned in the latest Errata sheets if the PCC_FB_ECC * Error occurs, the adapter will be recycled by disabling the - * adapter enable bit and enabling it again after the device + * adapter enable bit and enabling it again after the device * becomes Quiescent. */ val64 = readq(&bar0->pcc_err_reg); @@ -2354,18 +2181,18 @@ static void alarm_intr_handler(struct s2io_nic *nic) /* Other type of interrupts are not being handled now, TODO */ } -/** +/** * wait_for_cmd_complete - waits for a command to complete. - * @sp : private member of the device structure, which is a pointer to the + * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. - * Description: Function that waits for a command to Write into RMAC - * ADDR DATA registers to be completed and returns either success or - * error depending on whether the command was complete or not. + * Description: Function that waits for a command to Write into RMAC + * ADDR DATA registers to be completed and returns either success or + * error depending on whether the command was complete or not. * Return value: * SUCCESS on success and FAILURE on failure. */ -static int wait_for_cmd_complete(nic_t * sp) +int wait_for_cmd_complete(nic_t * sp) { XENA_dev_config_t __iomem *bar0 = sp->bar0; int ret = FAILURE, cnt = 0; @@ -2385,17 +2212,17 @@ static int wait_for_cmd_complete(nic_t * sp) return ret; } -/** - * s2io_reset - Resets the card. +/** + * s2io_reset - Resets the card. * @sp : private member of the device structure. * Description: Function to Reset the card. This function then also - * restores the previously saved PCI configuration space registers as + * restores the previously saved PCI configuration space registers as * the card reset also resets the configuration space. * Return value: * void. */ -static void s2io_reset(nic_t * sp) +void s2io_reset(nic_t * sp) { XENA_dev_config_t __iomem *bar0 = sp->bar0; u64 val64; @@ -2404,10 +2231,10 @@ static void s2io_reset(nic_t * sp) val64 = SW_RESET_ALL; writeq(val64, &bar0->sw_reset); - /* - * At this stage, if the PCI write is indeed completed, the - * card is reset and so is the PCI Config space of the device. - * So a read cannot be issued at this stage on any of the + /* + * At this stage, if the PCI write is indeed completed, the + * card is reset and so is the PCI Config space of the device. + * So a read cannot be issued at this stage on any of the * registers to ensure the write into "sw_reset" register * has gone through. * Question: Is there any system call that will explicitly force @@ -2420,10 +2247,17 @@ static void s2io_reset(nic_t * sp) /* Restore the PCI state saved during initializarion. */ pci_restore_state(sp->pdev); + s2io_init_pci(sp); msleep(250); + /* Set swapper to enable I/O register access */ + s2io_set_swapper(sp); + + /* Reset device statistics maintained by OS */ + memset(&sp->stats, 0, sizeof (struct net_device_stats)); + /* SXE-002: Configure link and activity LED to turn it off */ subid = sp->pdev->subsystem_device; if ((subid & 0xFF) >= 0x07) { @@ -2431,29 +2265,29 @@ static void s2io_reset(nic_t * sp) val64 |= 0x0000800000000000ULL; writeq(val64, &bar0->gpio_control); val64 = 0x0411040400000000ULL; - writeq(val64, (void __iomem *) bar0 + 0x2700); + writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700)); } sp->device_enabled_once = FALSE; } /** - * s2io_set_swapper - to set the swapper controle on the card - * @sp : private member of the device structure, + * s2io_set_swapper - to set the swapper controle on the card + * @sp : private member of the device structure, * pointer to the s2io_nic structure. - * Description: Function to set the swapper control on the card + * Description: Function to set the swapper control on the card * correctly depending on the 'endianness' of the system. * Return value: * SUCCESS on success and FAILURE on failure. */ -static int s2io_set_swapper(nic_t * sp) +int s2io_set_swapper(nic_t * sp) { struct net_device *dev = sp->dev; XENA_dev_config_t __iomem *bar0 = sp->bar0; u64 val64, valt, valr; - /* + /* * Set proper endian settings and verify the same by reading * the PIF Feed-back register. */ @@ -2505,8 +2339,9 @@ static int s2io_set_swapper(nic_t * sp) i++; } if(i == 4) { + unsigned long long x = val64; DBG_PRINT(ERR_DBG, "Write failed, Xmsi_addr "); - DBG_PRINT(ERR_DBG, "reads:0x%llx\n",val64); + DBG_PRINT(ERR_DBG, "reads:0x%llx\n", x); return FAILURE; } } @@ -2514,8 +2349,8 @@ static int s2io_set_swapper(nic_t * sp) val64 &= 0xFFFF000000000000ULL; #ifdef __BIG_ENDIAN - /* - * The device by default set to a big endian format, so a + /* + * The device by default set to a big endian format, so a * big endian driver need not set anything. */ val64 |= (SWAPPER_CTRL_TXP_FE | @@ -2531,9 +2366,9 @@ static int s2io_set_swapper(nic_t * sp) SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE); writeq(val64, &bar0->swapper_ctrl); #else - /* + /* * Initially we enable all bits to make it accessible by the - * driver, then we selectively enable only those bits that + * driver, then we selectively enable only those bits that * we want to set. */ val64 |= (SWAPPER_CTRL_TXP_FE | @@ -2555,8 +2390,8 @@ static int s2io_set_swapper(nic_t * sp) #endif val64 = readq(&bar0->swapper_ctrl); - /* - * Verifying if endian settings are accurate by reading a + /* + * Verifying if endian settings are accurate by reading a * feedback register. */ val64 = readq(&bar0->pif_rd_swapper_fb); @@ -2576,25 +2411,25 @@ static int s2io_set_swapper(nic_t * sp) * Functions defined below concern the OS part of the driver * * ********************************************************* */ -/** +/** * s2io_open - open entry point of the driver * @dev : pointer to the device structure. * Description: * This function is the open entry point of the driver. It mainly calls a * function to allocate Rx buffers and inserts them into the buffer - * descriptors and then enables the Rx part of the NIC. + * descriptors and then enables the Rx part of the NIC. * Return value: * 0 on success and an appropriate (-)ve integer as defined in errno.h * file on failure. */ -static int s2io_open(struct net_device *dev) +int s2io_open(struct net_device *dev) { nic_t *sp = dev->priv; int err = 0; - /* - * Make sure you have link off by default every time + /* + * Make sure you have link off by default every time * Nic is initialized */ netif_carrier_off(dev); @@ -2604,27 +2439,34 @@ static int s2io_open(struct net_device *dev) if (s2io_card_up(sp)) { DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n", dev->name); - return -ENODEV; + err = -ENODEV; + goto hw_init_failed; } /* After proper initialization of H/W, register ISR */ - err = request_irq((int) sp->irq, s2io_isr, SA_SHIRQ, + err = request_irq((int) sp->pdev->irq, s2io_isr, SA_SHIRQ, sp->name, dev); if (err) { - s2io_reset(sp); DBG_PRINT(ERR_DBG, "%s: ISR registration failed\n", dev->name); - return err; + goto isr_registration_failed; } if (s2io_set_mac_addr(dev, dev->dev_addr) == FAILURE) { DBG_PRINT(ERR_DBG, "Set Mac Address Failed\n"); - s2io_reset(sp); - return -ENODEV; + err = -ENODEV; + goto setting_mac_address_failed; } netif_start_queue(dev); return 0; + +setting_mac_address_failed: + free_irq(sp->pdev->irq, dev); +isr_registration_failed: + s2io_reset(sp); +hw_init_failed: + return err; } /** @@ -2640,16 +2482,15 @@ static int s2io_open(struct net_device *dev) * file on failure. */ -static int s2io_close(struct net_device *dev) +int s2io_close(struct net_device *dev) { nic_t *sp = dev->priv; - flush_scheduled_work(); netif_stop_queue(dev); /* Reset card, kill tasklet and free Tx and Rx buffers. */ s2io_card_down(sp); - free_irq(dev->irq, dev); + free_irq(sp->pdev->irq, dev); sp->device_close_flag = TRUE; /* Device is shut down. */ return 0; } @@ -2667,7 +2508,7 @@ static int s2io_close(struct net_device *dev) * 0 on success & 1 on failure. */ -static int s2io_xmit(struct sk_buff *skb, struct net_device *dev) +int s2io_xmit(struct sk_buff *skb, struct net_device *dev) { nic_t *sp = dev->priv; u16 frg_cnt, frg_len, i, queue, queue_len, put_off, get_off; @@ -2685,22 +2526,24 @@ static int s2io_xmit(struct sk_buff *skb, struct net_device *dev) mac_control = &sp->mac_control; config = &sp->config; - DBG_PRINT(TX_DBG, "%s: In S2IO Tx routine\n", dev->name); + DBG_PRINT(TX_DBG, "%s: In Neterion Tx routine\n", dev->name); spin_lock_irqsave(&sp->tx_lock, flags); - if (atomic_read(&sp->card_state) == CARD_DOWN) { - DBG_PRINT(ERR_DBG, "%s: Card going down for reset\n", + DBG_PRINT(TX_DBG, "%s: Card going down for reset\n", dev->name); spin_unlock_irqrestore(&sp->tx_lock, flags); - return 1; + dev_kfree_skb(skb); + return 0; } queue = 0; - put_off = (u16) mac_control->tx_curr_put_info[queue].offset; - get_off = (u16) mac_control->tx_curr_get_info[queue].offset; - txdp = (TxD_t *) sp->list_info[queue][put_off].list_virt_addr; - queue_len = mac_control->tx_curr_put_info[queue].fifo_len + 1; + put_off = (u16) mac_control->fifos[queue].tx_curr_put_info.offset; + get_off = (u16) mac_control->fifos[queue].tx_curr_get_info.offset; + txdp = (TxD_t *) mac_control->fifos[queue].list_info[put_off]. + list_virt_addr; + + queue_len = mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1; /* Avoid "put" pointer going beyond "get" pointer */ if (txdp->Host_Control || (((put_off + 1) % queue_len) == get_off)) { DBG_PRINT(ERR_DBG, "Error in xmit, No free TXDs.\n"); @@ -2720,9 +2563,9 @@ static int s2io_xmit(struct sk_buff *skb, struct net_device *dev) frg_cnt = skb_shinfo(skb)->nr_frags; frg_len = skb->len - skb->data_len; - txdp->Host_Control = (unsigned long) skb; txdp->Buffer_Pointer = pci_map_single (sp->pdev, skb->data, frg_len, PCI_DMA_TODEVICE); + txdp->Host_Control = (unsigned long) skb; if (skb->ip_summed == CHECKSUM_HW) { txdp->Control_2 |= (TXD_TX_CKO_IPV4_EN | TXD_TX_CKO_TCP_EN | @@ -2747,11 +2590,12 @@ static int s2io_xmit(struct sk_buff *skb, struct net_device *dev) txdp->Control_1 |= TXD_GATHER_CODE_LAST; tx_fifo = mac_control->tx_FIFO_start[queue]; - val64 = sp->list_info[queue][put_off].list_phy_addr; + val64 = mac_control->fifos[queue].list_info[put_off].list_phy_addr; writeq(val64, &tx_fifo->TxDL_Pointer); val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST | TX_FIFO_LAST_LIST); + #ifdef NETIF_F_TSO if (mss) val64 |= TX_FIFO_SPECIAL_FUNC; @@ -2762,8 +2606,8 @@ static int s2io_xmit(struct sk_buff *skb, struct net_device *dev) val64 = readq(&bar0->general_int_status); put_off++; - put_off %= mac_control->tx_curr_put_info[queue].fifo_len + 1; - mac_control->tx_curr_put_info[queue].offset = put_off; + put_off %= mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1; + mac_control->fifos[queue].tx_curr_put_info.offset = put_off; /* Avoid "put" pointer going beyond "get" pointer */ if (((put_off + 1) % queue_len) == get_off) { @@ -2784,13 +2628,13 @@ static int s2io_xmit(struct sk_buff *skb, struct net_device *dev) * @irq: the irq of the device. * @dev_id: a void pointer to the dev structure of the NIC. * @pt_regs: pointer to the registers pushed on the stack. - * Description: This function is the ISR handler of the device. It - * identifies the reason for the interrupt and calls the relevant - * service routines. As a contongency measure, this ISR allocates the + * Description: This function is the ISR handler of the device. It + * identifies the reason for the interrupt and calls the relevant + * service routines. As a contongency measure, this ISR allocates the * recv buffers, if their numbers are below the panic value which is * presently set to 25% of the original number of rcv buffers allocated. * Return value: - * IRQ_HANDLED: will be returned if IRQ was handled by this routine + * IRQ_HANDLED: will be returned if IRQ was handled by this routine * IRQ_NONE: will be returned if interrupt is not from our device */ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) @@ -2798,9 +2642,7 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) struct net_device *dev = (struct net_device *) dev_id; nic_t *sp = dev->priv; XENA_dev_config_t __iomem *bar0 = sp->bar0; -#ifndef CONFIG_S2IO_NAPI - int i, ret; -#endif + int i; u64 reason = 0; mac_info_t *mac_control; struct config_param *config; @@ -2808,13 +2650,13 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) mac_control = &sp->mac_control; config = &sp->config; - /* + /* * Identify the cause for interrupt and call the appropriate * interrupt handler. Causes for the interrupt could be; * 1. Rx of packet. * 2. Tx complete. * 3. Link down. - * 4. Error in any functional blocks of the NIC. + * 4. Error in any functional blocks of the NIC. */ reason = readq(&bar0->general_int_status); @@ -2823,12 +2665,6 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) return IRQ_NONE; } - /* If Intr is because of Tx Traffic */ - if (reason & GEN_INTR_TXTRAFFIC) { - tx_intr_handler(sp); - } - - /* If Intr is because of an error */ if (reason & (GEN_ERROR_INTR)) alarm_intr_handler(sp); @@ -2843,17 +2679,26 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) #else /* If Intr is because of Rx Traffic */ if (reason & GEN_INTR_RXTRAFFIC) { - rx_intr_handler(sp); + for (i = 0; i < config->rx_ring_num; i++) { + rx_intr_handler(&mac_control->rings[i]); + } } #endif - /* - * If the Rx buffer count is below the panic threshold then - * reallocate the buffers from the interrupt handler itself, + /* If Intr is because of Tx Traffic */ + if (reason & GEN_INTR_TXTRAFFIC) { + for (i = 0; i < config->tx_fifo_num; i++) + tx_intr_handler(&mac_control->fifos[i]); + } + + /* + * If the Rx buffer count is below the panic threshold then + * reallocate the buffers from the interrupt handler itself, * else schedule a tasklet to reallocate the buffers. */ #ifndef CONFIG_S2IO_NAPI for (i = 0; i < config->rx_ring_num; i++) { + int ret; int rxb_size = atomic_read(&sp->rx_bufs_left[i]); int level = rx_buffer_level(sp, rxb_size, i); @@ -2878,29 +2723,33 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) } /** - * s2io_get_stats - Updates the device statistics structure. + * s2io_get_stats - Updates the device statistics structure. * @dev : pointer to the device structure. * Description: - * This function updates the device statistics structure in the s2io_nic + * This function updates the device statistics structure in the s2io_nic * structure and returns a pointer to the same. * Return value: * pointer to the updated net_device_stats structure. */ -static struct net_device_stats *s2io_get_stats(struct net_device *dev) +struct net_device_stats *s2io_get_stats(struct net_device *dev) { nic_t *sp = dev->priv; mac_info_t *mac_control; struct config_param *config; + mac_control = &sp->mac_control; config = &sp->config; - sp->stats.tx_errors = mac_control->stats_info->tmac_any_err_frms; - sp->stats.rx_errors = mac_control->stats_info->rmac_drop_frms; - sp->stats.multicast = mac_control->stats_info->rmac_vld_mcst_frms; + sp->stats.tx_errors = + le32_to_cpu(mac_control->stats_info->tmac_any_err_frms); + sp->stats.rx_errors = + le32_to_cpu(mac_control->stats_info->rmac_drop_frms); + sp->stats.multicast = + le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms); sp->stats.rx_length_errors = - mac_control->stats_info->rmac_long_frms; + le32_to_cpu(mac_control->stats_info->rmac_long_frms); return (&sp->stats); } @@ -2909,8 +2758,8 @@ static struct net_device_stats *s2io_get_stats(struct net_device *dev) * s2io_set_multicast - entry point for multicast address enable/disable. * @dev : pointer to the device structure * Description: - * This function is a driver entry point which gets called by the kernel - * whenever multicast addresses must be enabled/disabled. This also gets + * This function is a driver entry point which gets called by the kernel + * whenever multicast addresses must be enabled/disabled. This also gets * called to set/reset promiscuous mode. Depending on the deivce flag, we * determine, if multicast address must be enabled or if promiscuous mode * is to be disabled etc. @@ -3010,7 +2859,7 @@ static void s2io_set_multicast(struct net_device *dev) writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr), &bar0->rmac_addr_data0_mem); writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL), - &bar0->rmac_addr_data1_mem); + &bar0->rmac_addr_data1_mem); val64 = RMAC_ADDR_CMD_MEM_WE | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD | RMAC_ADDR_CMD_MEM_OFFSET @@ -3039,8 +2888,7 @@ static void s2io_set_multicast(struct net_device *dev) writeq(RMAC_ADDR_DATA0_MEM_ADDR(mac_addr), &bar0->rmac_addr_data0_mem); writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL), - &bar0->rmac_addr_data1_mem); - + &bar0->rmac_addr_data1_mem); val64 = RMAC_ADDR_CMD_MEM_WE | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD | RMAC_ADDR_CMD_MEM_OFFSET @@ -3059,12 +2907,12 @@ static void s2io_set_multicast(struct net_device *dev) } /** - * s2io_set_mac_addr - Programs the Xframe mac address + * s2io_set_mac_addr - Programs the Xframe mac address * @dev : pointer to the device structure. * @addr: a uchar pointer to the new mac address which is to be set. - * Description : This procedure will program the Xframe to receive + * Description : This procedure will program the Xframe to receive * frames with new Mac Address - * Return value: SUCCESS on success and an appropriate (-)ve integer + * Return value: SUCCESS on success and an appropriate (-)ve integer * as defined in errno.h file on failure. */ @@ -3075,10 +2923,10 @@ int s2io_set_mac_addr(struct net_device *dev, u8 * addr) register u64 val64, mac_addr = 0; int i; - /* + /* * Set the new MAC address as the new unicast filter and reflect this * change on the device address registered with the OS. It will be - * at offset 0. + * at offset 0. */ for (i = 0; i < ETH_ALEN; i++) { mac_addr <<= 8; @@ -3102,12 +2950,12 @@ int s2io_set_mac_addr(struct net_device *dev, u8 * addr) } /** - * s2io_ethtool_sset - Sets different link parameters. + * s2io_ethtool_sset - Sets different link parameters. * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. * @info: pointer to the structure with parameters given by ethtool to set * link information. * Description: - * The function sets different link parameters provided by the user onto + * The function sets different link parameters provided by the user onto * the NIC. * Return value: * 0 on success. @@ -3129,7 +2977,7 @@ static int s2io_ethtool_sset(struct net_device *dev, } /** - * s2io_ethtol_gset - Return link specific information. + * s2io_ethtol_gset - Return link specific information. * @sp : private member of the device structure, pointer to the * s2io_nic structure. * @info : pointer to the structure with parameters given by ethtool @@ -3161,8 +3009,8 @@ static int s2io_ethtool_gset(struct net_device *dev, struct ethtool_cmd *info) } /** - * s2io_ethtool_gdrvinfo - Returns driver specific information. - * @sp : private member of the device structure, which is a pointer to the + * s2io_ethtool_gdrvinfo - Returns driver specific information. + * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. * @info : pointer to the structure with parameters given by ethtool to * return driver information. @@ -3190,9 +3038,9 @@ static void s2io_ethtool_gdrvinfo(struct net_device *dev, /** * s2io_ethtool_gregs - dumps the entire space of Xfame into the buffer. - * @sp: private member of the device structure, which is a pointer to the + * @sp: private member of the device structure, which is a pointer to the * s2io_nic structure. - * @regs : pointer to the structure with parameters given by ethtool for + * @regs : pointer to the structure with parameters given by ethtool for * dumping the registers. * @reg_space: The input argumnet into which all the registers are dumped. * Description: @@ -3221,11 +3069,11 @@ static void s2io_ethtool_gregs(struct net_device *dev, /** * s2io_phy_id - timer function that alternates adapter LED. - * @data : address of the private member of the device structure, which + * @data : address of the private member of the device structure, which * is a pointer to the s2io_nic structure, provided as an u32. - * Description: This is actually the timer function that alternates the - * adapter LED bit of the adapter control bit to set/reset every time on - * invocation. The timer is set for 1/2 a second, hence tha NIC blinks + * Description: This is actually the timer function that alternates the + * adapter LED bit of the adapter control bit to set/reset every time on + * invocation. The timer is set for 1/2 a second, hence tha NIC blinks * once every second. */ static void s2io_phy_id(unsigned long data) @@ -3253,12 +3101,12 @@ static void s2io_phy_id(unsigned long data) * s2io_ethtool_idnic - To physically identify the nic on the system. * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. - * @id : pointer to the structure with identification parameters given by + * @id : pointer to the structure with identification parameters given by * ethtool. * Description: Used to physically identify the NIC on the system. - * The Link LED will blink for a time specified by the user for + * The Link LED will blink for a time specified by the user for * identification. - * NOTE: The Link has to be Up to be able to blink the LED. Hence + * NOTE: The Link has to be Up to be able to blink the LED. Hence * identification is possible only if it's link is up. * Return value: * int , returns 0 on success @@ -3288,9 +3136,9 @@ static int s2io_ethtool_idnic(struct net_device *dev, u32 data) } mod_timer(&sp->id_timer, jiffies); if (data) - msleep(data * 1000); + msleep_interruptible(data * HZ); else - msleep(0xFFFFFFFF); + msleep_interruptible(MAX_FLICKER_TIME); del_timer_sync(&sp->id_timer); if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) { @@ -3303,7 +3151,8 @@ static int s2io_ethtool_idnic(struct net_device *dev, u32 data) /** * s2io_ethtool_getpause_data -Pause frame frame generation and reception. - * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. + * @sp : private member of the device structure, which is a pointer to the + * s2io_nic structure. * @ep : pointer to the structure with pause parameters given by ethtool. * Description: * Returns the Pause frame generation and reception capability of the NIC. @@ -3327,7 +3176,7 @@ static void s2io_ethtool_getpause_data(struct net_device *dev, /** * s2io_ethtool_setpause_data - set/reset pause frame generation. - * @sp : private member of the device structure, which is a pointer to the + * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. * @ep : pointer to the structure with pause parameters given by ethtool. * Description: @@ -3338,7 +3187,7 @@ static void s2io_ethtool_getpause_data(struct net_device *dev, */ static int s2io_ethtool_setpause_data(struct net_device *dev, - struct ethtool_pauseparam *ep) + struct ethtool_pauseparam *ep) { u64 val64; nic_t *sp = dev->priv; @@ -3359,13 +3208,13 @@ static int s2io_ethtool_setpause_data(struct net_device *dev, /** * read_eeprom - reads 4 bytes of data from user given offset. - * @sp : private member of the device structure, which is a pointer to the + * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. * @off : offset at which the data must be written * @data : Its an output parameter where the data read at the given - * offset is stored. + * offset is stored. * Description: - * Will read 4 bytes of data from the user given offset and return the + * Will read 4 bytes of data from the user given offset and return the * read data. * NOTE: Will allow to read only part of the EEPROM visible through the * I2C bus. @@ -3406,7 +3255,7 @@ static int read_eeprom(nic_t * sp, int off, u32 * data) * s2io_nic structure. * @off : offset at which the data must be written * @data : The data that is to be written - * @cnt : Number of bytes of the data that are actually to be written into + * @cnt : Number of bytes of the data that are actually to be written into * the Eeprom. (max of 3) * Description: * Actually writes the relevant part of the data value into the Eeprom @@ -3443,7 +3292,7 @@ static int write_eeprom(nic_t * sp, int off, u32 data, int cnt) /** * s2io_ethtool_geeprom - reads the value stored in the Eeprom. * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. - * @eeprom : pointer to the user level structure provided by ethtool, + * @eeprom : pointer to the user level structure provided by ethtool, * containing all relevant information. * @data_buf : user defined value to be written into Eeprom. * Description: Reads the values stored in the Eeprom at given offset @@ -3454,7 +3303,7 @@ static int write_eeprom(nic_t * sp, int off, u32 data, int cnt) */ static int s2io_ethtool_geeprom(struct net_device *dev, - struct ethtool_eeprom *eeprom, u8 * data_buf) + struct ethtool_eeprom *eeprom, u8 * data_buf) { u32 data, i, valid; nic_t *sp = dev->priv; @@ -3479,7 +3328,7 @@ static int s2io_ethtool_geeprom(struct net_device *dev, * s2io_ethtool_seeprom - tries to write the user provided value in Eeprom * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. - * @eeprom : pointer to the user level structure provided by ethtool, + * @eeprom : pointer to the user level structure provided by ethtool, * containing all relevant information. * @data_buf ; user defined value to be written into Eeprom. * Description: @@ -3527,8 +3376,8 @@ static int s2io_ethtool_seeprom(struct net_device *dev, } /** - * s2io_register_test - reads and writes into all clock domains. - * @sp : private member of the device structure, which is a pointer to the + * s2io_register_test - reads and writes into all clock domains. + * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. * @data : variable that returns the result of each of the test conducted b * by the driver. @@ -3545,8 +3394,8 @@ static int s2io_register_test(nic_t * sp, uint64_t * data) u64 val64 = 0; int fail = 0; - val64 = readq(&bar0->pcc_enable); - if (val64 != 0xff00000000000000ULL) { + val64 = readq(&bar0->pif_rd_swapper_fb); + if (val64 != 0x123456789abcdefULL) { fail = 1; DBG_PRINT(INFO_DBG, "Read Test level 1 fails\n"); } @@ -3590,13 +3439,13 @@ static int s2io_register_test(nic_t * sp, uint64_t * data) } /** - * s2io_eeprom_test - to verify that EEprom in the xena can be programmed. + * s2io_eeprom_test - to verify that EEprom in the xena can be programmed. * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. * @data:variable that returns the result of each of the test conducted by * the driver. * Description: - * Verify that EEPROM in the xena can be programmed using I2C_CONTROL + * Verify that EEPROM in the xena can be programmed using I2C_CONTROL * register. * Return value: * 0 on success. @@ -3661,14 +3510,14 @@ static int s2io_eeprom_test(nic_t * sp, uint64_t * data) /** * s2io_bist_test - invokes the MemBist test of the card . - * @sp : private member of the device structure, which is a pointer to the + * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. - * @data:variable that returns the result of each of the test conducted by + * @data:variable that returns the result of each of the test conducted by * the driver. * Description: * This invokes the MemBist test of the card. We give around * 2 secs time for the Test to complete. If it's still not complete - * within this peiod, we consider that the test failed. + * within this peiod, we consider that the test failed. * Return value: * 0 on success and -1 on failure. */ @@ -3697,13 +3546,13 @@ static int s2io_bist_test(nic_t * sp, uint64_t * data) } /** - * s2io-link_test - verifies the link state of the nic - * @sp ; private member of the device structure, which is a pointer to the + * s2io-link_test - verifies the link state of the nic + * @sp ; private member of the device structure, which is a pointer to the * s2io_nic structure. * @data: variable that returns the result of each of the test conducted by * the driver. * Description: - * The function verifies the link state of the NIC and updates the input + * The function verifies the link state of the NIC and updates the input * argument 'data' appropriately. * Return value: * 0 on success. @@ -3722,13 +3571,13 @@ static int s2io_link_test(nic_t * sp, uint64_t * data) } /** - * s2io_rldram_test - offline test for access to the RldRam chip on the NIC - * @sp - private member of the device structure, which is a pointer to the + * s2io_rldram_test - offline test for access to the RldRam chip on the NIC + * @sp - private member of the device structure, which is a pointer to the * s2io_nic structure. - * @data - variable that returns the result of each of the test + * @data - variable that returns the result of each of the test * conducted by the driver. * Description: - * This is one of the offline test that tests the read and write + * This is one of the offline test that tests the read and write * access to the RldRam chip on the NIC. * Return value: * 0 on success. @@ -3833,7 +3682,7 @@ static int s2io_rldram_test(nic_t * sp, uint64_t * data) * s2io_nic structure. * @ethtest : pointer to a ethtool command specific structure that will be * returned to the user. - * @data : variable that returns the result of each of the test + * @data : variable that returns the result of each of the test * conducted by the driver. * Description: * This function conducts 6 tests ( 4 offline and 2 online) to determine @@ -3851,23 +3700,18 @@ static void s2io_ethtool_test(struct net_device *dev, if (ethtest->flags == ETH_TEST_FL_OFFLINE) { /* Offline Tests. */ - if (orig_state) { + if (orig_state) s2io_close(sp->dev); - s2io_set_swapper(sp); - } else - s2io_set_swapper(sp); if (s2io_register_test(sp, &data[0])) ethtest->flags |= ETH_TEST_FL_FAILED; s2io_reset(sp); - s2io_set_swapper(sp); if (s2io_rldram_test(sp, &data[3])) ethtest->flags |= ETH_TEST_FL_FAILED; s2io_reset(sp); - s2io_set_swapper(sp); if (s2io_eeprom_test(sp, &data[1])) ethtest->flags |= ETH_TEST_FL_FAILED; @@ -3951,20 +3795,19 @@ static void s2io_get_ethtool_stats(struct net_device *dev, tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp); } -static int s2io_ethtool_get_regs_len(struct net_device *dev) +int s2io_ethtool_get_regs_len(struct net_device *dev) { return (XENA_REG_SPACE); } -static u32 s2io_ethtool_get_rx_csum(struct net_device * dev) +u32 s2io_ethtool_get_rx_csum(struct net_device * dev) { nic_t *sp = dev->priv; return (sp->rx_csum); } - -static int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data) +int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data) { nic_t *sp = dev->priv; @@ -3975,19 +3818,17 @@ static int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data) return 0; } - -static int s2io_get_eeprom_len(struct net_device *dev) +int s2io_get_eeprom_len(struct net_device *dev) { return (XENA_EEPROM_SPACE); } -static int s2io_ethtool_self_test_count(struct net_device *dev) +int s2io_ethtool_self_test_count(struct net_device *dev) { return (S2IO_TEST_LEN); } - -static void s2io_ethtool_get_strings(struct net_device *dev, - u32 stringset, u8 * data) +void s2io_ethtool_get_strings(struct net_device *dev, + u32 stringset, u8 * data) { switch (stringset) { case ETH_SS_TEST: @@ -3998,13 +3839,12 @@ static void s2io_ethtool_get_strings(struct net_device *dev, sizeof(ethtool_stats_keys)); } } - static int s2io_ethtool_get_stats_count(struct net_device *dev) { return (S2IO_STAT_LEN); } -static int s2io_ethtool_op_set_tx_csum(struct net_device *dev, u32 data) +int s2io_ethtool_op_set_tx_csum(struct net_device *dev, u32 data) { if (data) dev->features |= NETIF_F_IP_CSUM; @@ -4046,21 +3886,18 @@ static struct ethtool_ops netdev_ethtool_ops = { }; /** - * s2io_ioctl - Entry point for the Ioctl + * s2io_ioctl - Entry point for the Ioctl * @dev : Device pointer. * @ifr : An IOCTL specefic structure, that can contain a pointer to * a proprietary structure used to pass information to the driver. * @cmd : This is used to distinguish between the different commands that * can be passed to the IOCTL functions. * Description: - * This function has support for ethtool, adding multiple MAC addresses on - * the NIC and some DBG commands for the util tool. - * Return value: - * Currently the IOCTL supports no operations, hence by default this - * function returns OP NOT SUPPORTED value. + * Currently there are no special functionality supported in IOCTL, hence + * function always return EOPNOTSUPPORTED */ -static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) +int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) { return -EOPNOTSUPP; } @@ -4076,7 +3913,7 @@ static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) * file on failure. */ -static int s2io_change_mtu(struct net_device *dev, int new_mtu) +int s2io_change_mtu(struct net_device *dev, int new_mtu) { nic_t *sp = dev->priv; XENA_dev_config_t __iomem *bar0 = sp->bar0; @@ -4084,7 +3921,7 @@ static int s2io_change_mtu(struct net_device *dev, int new_mtu) if (netif_running(dev)) { DBG_PRINT(ERR_DBG, "%s: Must be stopped to ", dev->name); - DBG_PRINT(ERR_DBG, "change its MTU \n"); + DBG_PRINT(ERR_DBG, "change its MTU\n"); return -EBUSY; } @@ -4108,9 +3945,9 @@ static int s2io_change_mtu(struct net_device *dev, int new_mtu) * @dev_adr : address of the device structure in dma_addr_t format. * Description: * This is the tasklet or the bottom half of the ISR. This is - * an extension of the ISR which is scheduled by the scheduler to be run + * an extension of the ISR which is scheduled by the scheduler to be run * when the load on the CPU is low. All low priority tasks of the ISR can - * be pushed into the tasklet. For now the tasklet is used only to + * be pushed into the tasklet. For now the tasklet is used only to * replenish the Rx buffers in the Rx buffer descriptors. * Return value: * void. @@ -4166,14 +4003,14 @@ static void s2io_set_link(unsigned long data) } subid = nic->pdev->subsystem_device; - /* - * Allow a small delay for the NICs self initiated + /* + * Allow a small delay for the NICs self initiated * cleanup to complete. */ msleep(100); val64 = readq(&bar0->adapter_status); - if (verify_xena_quiescence(val64, nic->device_enabled_once)) { + if (verify_xena_quiescence(nic, val64, nic->device_enabled_once)) { if (LINK_IS_UP(val64)) { val64 = readq(&bar0->adapter_control); val64 |= ADAPTER_CNTL_EN; @@ -4224,8 +4061,9 @@ static void s2io_card_down(nic_t * sp) register u64 val64 = 0; /* If s2io_set_link task is executing, wait till it completes. */ - while (test_and_set_bit(0, &(sp->link_state))) + while (test_and_set_bit(0, &(sp->link_state))) { msleep(50); + } atomic_set(&sp->card_state, CARD_DOWN); /* disable Tx and Rx traffic on the NIC */ @@ -4237,7 +4075,7 @@ static void s2io_card_down(nic_t * sp) /* Check if the device is Quiescent and then Reset the NIC */ do { val64 = readq(&bar0->adapter_status); - if (verify_xena_quiescence(val64, sp->device_enabled_once)) { + if (verify_xena_quiescence(sp, val64, sp->device_enabled_once)) { break; } @@ -4276,8 +4114,8 @@ static int s2io_card_up(nic_t * sp) return -ENODEV; } - /* - * Initializing the Rx buffers. For now we are considering only 1 + /* + * Initializing the Rx buffers. For now we are considering only 1 * Rx ring and initializing buffers into 30 Rx blocks */ mac_control = &sp->mac_control; @@ -4315,12 +4153,12 @@ static int s2io_card_up(nic_t * sp) return 0; } -/** +/** * s2io_restart_nic - Resets the NIC. * @data : long pointer to the device private structure * Description: * This function is scheduled to be run by the s2io_tx_watchdog - * function after 0.5 secs to reset the NIC. The idea is to reduce + * function after 0.5 secs to reset the NIC. The idea is to reduce * the run time of the watch dog routine which is run holding a * spin lock. */ @@ -4338,10 +4176,11 @@ static void s2io_restart_nic(unsigned long data) netif_wake_queue(dev); DBG_PRINT(ERR_DBG, "%s: was reset by Tx watchdog timer\n", dev->name); + } -/** - * s2io_tx_watchdog - Watchdog for transmit side. +/** + * s2io_tx_watchdog - Watchdog for transmit side. * @dev : Pointer to net device structure * Description: * This function is triggered if the Tx Queue is stopped @@ -4369,7 +4208,7 @@ static void s2io_tx_watchdog(struct net_device *dev) * @len : length of the packet * @cksum : FCS checksum of the frame. * @ring_no : the ring from which this RxD was extracted. - * Description: + * Description: * This function is called by the Tx interrupt serivce routine to perform * some OS related operations on the SKB before passing it to the upper * layers. It mainly checks if the checksum is OK, if so adds it to the @@ -4379,35 +4218,63 @@ static void s2io_tx_watchdog(struct net_device *dev) * Return value: * SUCCESS on success and -1 on failure. */ -#ifndef CONFIG_2BUFF_MODE -static int rx_osm_handler(nic_t * sp, u16 len, RxD_t * rxdp, int ring_no) -#else -static int rx_osm_handler(nic_t * sp, RxD_t * rxdp, int ring_no, - buffAdd_t * ba) -#endif +static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp) { + nic_t *sp = ring_data->nic; struct net_device *dev = (struct net_device *) sp->dev; - struct sk_buff *skb = - (struct sk_buff *) ((unsigned long) rxdp->Host_Control); + struct sk_buff *skb = (struct sk_buff *) + ((unsigned long) rxdp->Host_Control); + int ring_no = ring_data->ring_no; u16 l3_csum, l4_csum; #ifdef CONFIG_2BUFF_MODE - int buf0_len, buf2_len; + int buf0_len = RXD_GET_BUFFER0_SIZE(rxdp->Control_2); + int buf2_len = RXD_GET_BUFFER2_SIZE(rxdp->Control_2); + int get_block = ring_data->rx_curr_get_info.block_index; + int get_off = ring_data->rx_curr_get_info.offset; + buffAdd_t *ba = &ring_data->ba[get_block][get_off]; unsigned char *buff; +#else + u16 len = (u16) ((RXD_GET_BUFFER0_SIZE(rxdp->Control_2)) >> 48);; #endif + skb->dev = dev; + if (rxdp->Control_1 & RXD_T_CODE) { + unsigned long long err = rxdp->Control_1 & RXD_T_CODE; + DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%llx\n", + dev->name, err); + } - l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1); - if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) && (sp->rx_csum)) { + /* Updating statistics */ + rxdp->Host_Control = 0; + sp->rx_pkt_count++; + sp->stats.rx_packets++; +#ifndef CONFIG_2BUFF_MODE + sp->stats.rx_bytes += len; +#else + sp->stats.rx_bytes += buf0_len + buf2_len; +#endif + +#ifndef CONFIG_2BUFF_MODE + skb_put(skb, len); +#else + buff = skb_push(skb, buf0_len); + memcpy(buff, ba->ba_0, buf0_len); + skb_put(skb, buf2_len); +#endif + + if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) && + (sp->rx_csum)) { + l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1); l4_csum = RXD_GET_L4_CKSUM(rxdp->Control_1); if ((l3_csum == L3_CKSUM_OK) && (l4_csum == L4_CKSUM_OK)) { - /* + /* * NIC verifies if the Checksum of the received * frame is Ok or not and accordingly returns * a flag in the RxD. */ skb->ip_summed = CHECKSUM_UNNECESSARY; } else { - /* - * Packet with erroneous checksum, let the + /* + * Packet with erroneous checksum, let the * upper layers deal with it. */ skb->ip_summed = CHECKSUM_NONE; @@ -4416,44 +4283,14 @@ static int rx_osm_handler(nic_t * sp, RxD_t * rxdp, int ring_no, skb->ip_summed = CHECKSUM_NONE; } - if (rxdp->Control_1 & RXD_T_CODE) { - unsigned long long err = rxdp->Control_1 & RXD_T_CODE; - DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%llx\n", - dev->name, err); - } -#ifdef CONFIG_2BUFF_MODE - buf0_len = RXD_GET_BUFFER0_SIZE(rxdp->Control_2); - buf2_len = RXD_GET_BUFFER2_SIZE(rxdp->Control_2); -#endif - - skb->dev = dev; -#ifndef CONFIG_2BUFF_MODE - skb_put(skb, len); skb->protocol = eth_type_trans(skb, dev); -#else - buff = skb_push(skb, buf0_len); - memcpy(buff, ba->ba_0, buf0_len); - skb_put(skb, buf2_len); - skb->protocol = eth_type_trans(skb, dev); -#endif - #ifdef CONFIG_S2IO_NAPI netif_receive_skb(skb); #else netif_rx(skb); #endif - dev->last_rx = jiffies; - sp->rx_pkt_count++; - sp->stats.rx_packets++; -#ifndef CONFIG_2BUFF_MODE - sp->stats.rx_bytes += len; -#else - sp->stats.rx_bytes += buf0_len + buf2_len; -#endif - atomic_dec(&sp->rx_bufs_left[ring_no]); - rxdp->Host_Control = 0; return SUCCESS; } @@ -4464,13 +4301,13 @@ static int rx_osm_handler(nic_t * sp, RxD_t * rxdp, int ring_no, * @link : inidicates whether link is UP/DOWN. * Description: * This function stops/starts the Tx queue depending on whether the link - * status of the NIC is is down or up. This is called by the Alarm - * interrupt handler whenever a link change interrupt comes up. + * status of the NIC is is down or up. This is called by the Alarm + * interrupt handler whenever a link change interrupt comes up. * Return value: * void. */ -static void s2io_link(nic_t * sp, int link) +void s2io_link(nic_t * sp, int link) { struct net_device *dev = (struct net_device *) sp->dev; @@ -4487,8 +4324,25 @@ static void s2io_link(nic_t * sp, int link) } /** - * s2io_init_pci -Initialization of PCI and PCI-X configuration registers . - * @sp : private member of the device structure, which is a pointer to the + * get_xena_rev_id - to identify revision ID of xena. + * @pdev : PCI Dev structure + * Description: + * Function to identify the Revision ID of xena. + * Return value: + * returns the revision ID of the device. + */ + +int get_xena_rev_id(struct pci_dev *pdev) +{ + u8 id = 0; + int ret; + ret = pci_read_config_byte(pdev, PCI_REVISION_ID, (u8 *) & id); + return id; +} + +/** + * s2io_init_pci -Initialization of PCI and PCI-X configuration registers . + * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure. * Description: * This function initializes a few of the PCI and PCI-X configuration registers @@ -4499,15 +4353,15 @@ static void s2io_link(nic_t * sp, int link) static void s2io_init_pci(nic_t * sp) { - u16 pci_cmd = 0; + u16 pci_cmd = 0, pcix_cmd = 0; /* Enable Data Parity Error Recovery in PCI-X command register. */ pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - &(sp->pcix_cmd)); + &(pcix_cmd)); pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - (sp->pcix_cmd | 1)); + (pcix_cmd | 1)); pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - &(sp->pcix_cmd)); + &(pcix_cmd)); /* Set the PErr Response bit in PCI command register. */ pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd); @@ -4516,34 +4370,36 @@ static void s2io_init_pci(nic_t * sp) pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd); /* Set MMRB count to 1024 in PCI-X Command register. */ - sp->pcix_cmd &= 0xFFF3; - pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, (sp->pcix_cmd | (0x1 << 2))); /* MMRBC 1K */ + pcix_cmd &= 0xFFF3; + pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, + (pcix_cmd | (0x1 << 2))); /* MMRBC 1K */ pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - &(sp->pcix_cmd)); + &(pcix_cmd)); /* Setting Maximum outstanding splits based on system type. */ - sp->pcix_cmd &= 0xFF8F; - - sp->pcix_cmd |= XENA_MAX_OUTSTANDING_SPLITS(0x1); /* 2 splits. */ + pcix_cmd &= 0xFF8F; + pcix_cmd |= XENA_MAX_OUTSTANDING_SPLITS(0x1); /* 2 splits. */ pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - sp->pcix_cmd); + pcix_cmd); pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - &(sp->pcix_cmd)); + &(pcix_cmd)); + /* Forcibly disabling relaxed ordering capability of the card. */ - sp->pcix_cmd &= 0xfffd; + pcix_cmd &= 0xfffd; pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - sp->pcix_cmd); + pcix_cmd); pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - &(sp->pcix_cmd)); + &(pcix_cmd)); } MODULE_AUTHOR("Raghavendra Koushik "); MODULE_LICENSE("GPL"); module_param(tx_fifo_num, int, 0); -module_param_array(tx_fifo_len, int, NULL, 0); module_param(rx_ring_num, int, 0); -module_param_array(rx_ring_sz, int, NULL, 0); +module_param_array(tx_fifo_len, uint, NULL, 0); +module_param_array(rx_ring_sz, uint, NULL, 0); module_param(Stats_refresh_time, int, 0); +module_param_array(rts_frm_len, uint, NULL, 0); module_param(rmac_pause_time, int, 0); module_param(mc_pause_threshold_q0q3, int, 0); module_param(mc_pause_threshold_q4q7, int, 0); @@ -4553,15 +4409,16 @@ module_param(rmac_util_period, int, 0); #ifndef CONFIG_S2IO_NAPI module_param(indicate_max_pkts, int, 0); #endif + /** - * s2io_init_nic - Initialization of the adapter . + * s2io_init_nic - Initialization of the adapter . * @pdev : structure containing the PCI related information of the device. * @pre: List of PCI devices supported by the driver listed in s2io_tbl. * Description: * The function initializes an adapter identified by the pci_dec structure. - * All OS related initialization including memory and device structure and - * initlaization of the device private variable is done. Also the swapper - * control register is initialized to enable read and write into the I/O + * All OS related initialization including memory and device structure and + * initlaization of the device private variable is done. Also the swapper + * control register is initialized to enable read and write into the I/O * registers of the device. * Return value: * returns 0 on success and negative on failure. @@ -4572,7 +4429,6 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) { nic_t *sp; struct net_device *dev; - char *dev_name = "S2IO 10GE NIC"; int i, j, ret; int dma_flag = FALSE; u32 mac_up, mac_down; @@ -4582,9 +4438,9 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) mac_info_t *mac_control; struct config_param *config; - - DBG_PRINT(ERR_DBG, "Loading S2IO driver with %s\n", - s2io_driver_version); +#ifdef CONFIG_S2IO_NAPI + DBG_PRINT(ERR_DBG, "NAPI support has been enabled\n"); +#endif if ((ret = pci_enable_device(pdev))) { DBG_PRINT(ERR_DBG, @@ -4595,7 +4451,6 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) { DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 64bit DMA\n"); dma_flag = TRUE; - if (pci_set_consistent_dma_mask (pdev, DMA_64BIT_MASK)) { DBG_PRINT(ERR_DBG, @@ -4635,21 +4490,17 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) memset(sp, 0, sizeof(nic_t)); sp->dev = dev; sp->pdev = pdev; - sp->vendor_id = pdev->vendor; - sp->device_id = pdev->device; sp->high_dma_flag = dma_flag; - sp->irq = pdev->irq; sp->device_enabled_once = FALSE; - strcpy(sp->name, dev_name); /* Initialize some PCI/PCI-X fields of the NIC. */ s2io_init_pci(sp); - /* + /* * Setting the device configuration parameters. - * Most of these parameters can be specified by the user during - * module insertion as they are module loadable parameters. If - * these parameters are not not specified during load time, they + * Most of these parameters can be specified by the user during + * module insertion as they are module loadable parameters. If + * these parameters are not not specified during load time, they * are initialized with default values. */ mac_control = &sp->mac_control; @@ -4663,6 +4514,10 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) config->tx_cfg[i].fifo_priority = i; } + /* mapping the QoS priority to the configured fifos */ + for (i = 0; i < MAX_TX_FIFOS; i++) + config->fifo_mapping[i] = fifo_map[config->tx_fifo_num][i]; + config->tx_intr_type = TXD_INT_TYPE_UTILZ; for (i = 0; i < config->tx_fifo_num; i++) { config->tx_cfg[i].f_no_snoop = @@ -4743,13 +4598,14 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) dev->do_ioctl = &s2io_ioctl; dev->change_mtu = &s2io_change_mtu; SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops); + /* * will use eth_mac_addr() for dev->set_mac_address * mac address will be set every time dev->open() is called */ -#ifdef CONFIG_S2IO_NAPI +#if defined(CONFIG_S2IO_NAPI) dev->poll = s2io_poll; - dev->weight = 90; + dev->weight = 32; #endif dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM; @@ -4776,22 +4632,14 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) goto set_swap_failed; } - /* Fix for all "FFs" MAC address problems observed on Alpha platforms */ + /* + * Fix for all "FFs" MAC address problems observed on + * Alpha platforms + */ fix_mac_address(sp); s2io_reset(sp); /* - * Setting swapper control on the NIC, so the MAC address can be read. - */ - if (s2io_set_swapper(sp)) { - DBG_PRINT(ERR_DBG, - "%s: S2IO: swapper settings are wrong\n", - dev->name); - ret = -EAGAIN; - goto set_swap_failed; - } - - /* * MAC address initialization. * For now only one mac address will be read and used. */ @@ -4828,23 +4676,22 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN); /* - * Initialize the tasklet status and link state flags + * Initialize the tasklet status and link state flags * and the card statte parameter */ atomic_set(&(sp->card_state), 0); sp->tasklet_status = 0; sp->link_state = 0; - /* Initialize spinlocks */ spin_lock_init(&sp->tx_lock); #ifndef CONFIG_S2IO_NAPI spin_lock_init(&sp->put_lock); #endif - /* - * SXE-002: Configure link and activity LED to init state - * on driver load. + /* + * SXE-002: Configure link and activity LED to init state + * on driver load. */ subid = sp->pdev->subsystem_device; if ((subid & 0xFF) >= 0x07) { @@ -4864,9 +4711,9 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) goto register_failed; } - /* - * Make Link state as off at this point, when the Link change - * interrupt comes the state will be automatically changed to + /* + * Make Link state as off at this point, when the Link change + * interrupt comes the state will be automatically changed to * the right state. */ netif_carrier_off(dev); @@ -4891,11 +4738,11 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) } /** - * s2io_rem_nic - Free the PCI device + * s2io_rem_nic - Free the PCI device * @pdev: structure containing the PCI related information of the device. - * Description: This function is called by the Pci subsystem to release a + * Description: This function is called by the Pci subsystem to release a * PCI device and free up all resource held up by the device. This could - * be in response to a Hot plug event or when the driver is to be removed + * be in response to a Hot plug event or when the driver is to be removed * from memory. */ @@ -4919,7 +4766,6 @@ static void __devexit s2io_rem_nic(struct pci_dev *pdev) pci_disable_device(pdev); pci_release_regions(pdev); pci_set_drvdata(pdev, NULL); - free_netdev(dev); } @@ -4935,11 +4781,11 @@ int __init s2io_starter(void) } /** - * s2io_closer - Cleanup routine for the driver + * s2io_closer - Cleanup routine for the driver * Description: This function is the cleanup routine for the driver. It unregist * ers the driver. */ -static void s2io_closer(void) +void s2io_closer(void) { pci_unregister_driver(&s2io_driver); DBG_PRINT(INIT_DBG, "cleanup done\n"); diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index 1711c8c..4d2fc7a 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -31,6 +31,9 @@ #define SUCCESS 0 #define FAILURE -1 +/* Maximum time to flicker LED when asked to identify NIC using ethtool */ +#define MAX_FLICKER_TIME 60000 /* 60 Secs */ + /* Maximum outstanding splits to be configured into xena. */ typedef enum xena_max_outstanding_splits { XENA_ONE_SPLIT_TRANSACTION = 0, @@ -45,10 +48,10 @@ typedef enum xena_max_outstanding_splits { #define XENA_MAX_OUTSTANDING_SPLITS(n) (n << 4) /* OS concerned variables and constants */ -#define WATCH_DOG_TIMEOUT 5*HZ -#define EFILL 0x1234 -#define ALIGN_SIZE 127 -#define PCIX_COMMAND_REGISTER 0x62 +#define WATCH_DOG_TIMEOUT 15*HZ +#define EFILL 0x1234 +#define ALIGN_SIZE 127 +#define PCIX_COMMAND_REGISTER 0x62 /* * Debug related variables. @@ -61,7 +64,7 @@ typedef enum xena_max_outstanding_splits { #define INTR_DBG 4 /* Global variable that defines the present debug level of the driver. */ -static int debug_level = ERR_DBG; /* Default level. */ +int debug_level = ERR_DBG; /* Default level. */ /* DEBUG message print. */ #define DBG_PRINT(dbg_level, args...) if(!(debug_level> 48) @@ -382,7 +408,7 @@ typedef struct _RxD_t { #endif } RxD_t; -/* Structure that represents the Rx descriptor block which contains +/* Structure that represents the Rx descriptor block which contains * 128 Rx descriptors. */ #ifndef CONFIG_2BUFF_MODE @@ -392,11 +418,11 @@ typedef struct _RxD_block { u64 reserved_0; #define END_OF_BLOCK 0xFEFFFFFFFFFFFFFFULL - u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last + u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last * Rxd in this blk */ u64 reserved_2_pNext_RxD_block; /* Logical ptr to next */ u64 pNext_RxD_Blk_physical; /* Buff0_ptr.In a 32 bit arch - * the upper 32 bits should + * the upper 32 bits should * be 0 */ } RxD_block_t; #else @@ -405,13 +431,13 @@ typedef struct _RxD_block { RxD_t rxd[MAX_RXDS_PER_BLOCK]; #define END_OF_BLOCK 0xFEFFFFFFFFFFFFFFULL - u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last Rxd + u64 reserved_1; /* 0xFEFFFFFFFFFFFFFF to mark last Rxd * in this blk */ u64 pNext_RxD_Blk_physical; /* Phy ponter to next blk. */ } RxD_block_t; #define SIZE_OF_BLOCK 4096 -/* Structure to hold virtual addresses of Buf0 and Buf1 in +/* Structure to hold virtual addresses of Buf0 and Buf1 in * 2buf mode. */ typedef struct bufAdd { void *ba_0_org; @@ -423,8 +449,8 @@ typedef struct bufAdd { /* Structure which stores all the MAC control parameters */ -/* This structure stores the offset of the RxD in the ring - * from which the Rx Interrupt processor can start picking +/* This structure stores the offset of the RxD in the ring + * from which the Rx Interrupt processor can start picking * up the RxDs for processing. */ typedef struct _rx_curr_get_info_t { @@ -436,7 +462,7 @@ typedef struct _rx_curr_get_info_t { typedef rx_curr_get_info_t rx_curr_put_info_t; /* This structure stores the offset of the TxDl in the FIFO - * from which the Tx Interrupt processor can start picking + * from which the Tx Interrupt processor can start picking * up the TxDLs for send complete interrupt processing. */ typedef struct { @@ -446,32 +472,96 @@ typedef struct { typedef tx_curr_get_info_t tx_curr_put_info_t; -/* Infomation related to the Tx and Rx FIFOs and Rings of Xena - * is maintained in this structure. - */ -typedef struct mac_info { -/* rx side stuff */ - /* Put pointer info which indictes which RxD has to be replenished +/* Structure that holds the Phy and virt addresses of the Blocks */ +typedef struct rx_block_info { + RxD_t *block_virt_addr; + dma_addr_t block_dma_addr; +} rx_block_info_t; + +/* pre declaration of the nic structure */ +typedef struct s2io_nic nic_t; + +/* Ring specific structure */ +typedef struct ring_info { + /* The ring number */ + int ring_no; + + /* + * Place holders for the virtual and physical addresses of + * all the Rx Blocks + */ + rx_block_info_t rx_blocks[MAX_RX_BLOCKS_PER_RING]; + int block_count; + int pkt_cnt; + + /* + * Put pointer info which indictes which RxD has to be replenished * with a new buffer. */ - rx_curr_put_info_t rx_curr_put_info[MAX_RX_RINGS]; + rx_curr_put_info_t rx_curr_put_info; - /* Get pointer info which indictes which is the last RxD that was + /* + * Get pointer info which indictes which is the last RxD that was * processed by the driver. */ - rx_curr_get_info_t rx_curr_get_info[MAX_RX_RINGS]; + rx_curr_get_info_t rx_curr_get_info; - u16 rmac_pause_time; - u16 mc_pause_threshold_q0q3; - u16 mc_pause_threshold_q4q7; +#ifndef CONFIG_S2IO_NAPI + /* Index to the absolute position of the put pointer of Rx ring */ + int put_pos; +#endif + +#ifdef CONFIG_2BUFF_MODE + /* Buffer Address store. */ + buffAdd_t **ba; +#endif + nic_t *nic; +} ring_info_t; +/* Fifo specific structure */ +typedef struct fifo_info { + /* FIFO number */ + int fifo_no; + + /* Maximum TxDs per TxDL */ + int max_txds; + + /* Place holder of all the TX List's Phy and Virt addresses. */ + list_info_hold_t *list_info; + + /* + * Current offset within the tx FIFO where driver would write + * new Tx frame + */ + tx_curr_put_info_t tx_curr_put_info; + + /* + * Current offset within tx FIFO from where the driver would start freeing + * the buffers + */ + tx_curr_get_info_t tx_curr_get_info; + + nic_t *nic; +}fifo_info_t; + +/* Infomation related to the Tx and Rx FIFOs and Rings of Xena + * is maintained in this structure. + */ +typedef struct mac_info { /* tx side stuff */ /* logical pointer of start of each Tx FIFO */ TxFIFO_element_t __iomem *tx_FIFO_start[MAX_TX_FIFOS]; -/* Current offset within tx_FIFO_start, where driver would write new Tx frame*/ - tx_curr_put_info_t tx_curr_put_info[MAX_TX_FIFOS]; - tx_curr_get_info_t tx_curr_get_info[MAX_TX_FIFOS]; + /* Fifo specific structure */ + fifo_info_t fifos[MAX_TX_FIFOS]; + +/* rx side stuff */ + /* Ring specific structure */ + ring_info_t rings[MAX_RX_RINGS]; + + u16 rmac_pause_time; + u16 mc_pause_threshold_q0q3; + u16 mc_pause_threshold_q4q7; void *stats_mem; /* orignal pointer to allocated mem */ dma_addr_t stats_mem_phy; /* Physical address of the stat block */ @@ -485,12 +575,6 @@ typedef struct { int usage_cnt; } usr_addr_t; -/* Structure that holds the Phy and virt addresses of the Blocks */ -typedef struct rx_block_info { - RxD_t *block_virt_addr; - dma_addr_t block_dma_addr; -} rx_block_info_t; - /* Default Tunable parameters of the NIC. */ #define DEFAULT_FIFO_LEN 4096 #define SMALL_RXD_CNT 30 * (MAX_RXDS_PER_BLOCK+1) @@ -499,7 +583,20 @@ typedef struct rx_block_info { #define LARGE_BLK_CNT 100 /* Structure representing one instance of the NIC */ -typedef struct s2io_nic { +struct s2io_nic { +#ifdef CONFIG_S2IO_NAPI + /* + * Count of packets to be processed in a given iteration, it will be indicated + * by the quota field of the device structure when NAPI is enabled. + */ + int pkts_to_process; +#endif + struct net_device *dev; + mac_info_t mac_control; + struct config_param config; + struct pci_dev *pdev; + void __iomem *bar0; + void __iomem *bar1; #define MAX_MAC_SUPPORTED 16 #define MAX_SUPPORTED_MULTICASTS MAX_MAC_SUPPORTED @@ -507,33 +604,17 @@ typedef struct s2io_nic { macaddr_t pre_mac_addr[MAX_MAC_SUPPORTED]; struct net_device_stats stats; - void __iomem *bar0; - void __iomem *bar1; - struct config_param config; - mac_info_t mac_control; int high_dma_flag; int device_close_flag; int device_enabled_once; - char name[32]; + char name[50]; struct tasklet_struct task; volatile unsigned long tasklet_status; - struct timer_list timer; - struct net_device *dev; - struct pci_dev *pdev; - u16 vendor_id; - u16 device_id; - u16 ccmd; - u32 cbar0_1; - u32 cbar0_2; - u32 cbar1_1; - u32 cbar1_2; - u32 cirq; - u8 cache_line; - u32 rom_expansion; - u16 pcix_cmd; - u32 irq; + /* Space to back up the PCI config space */ + u32 config_space[256 / sizeof(u32)]; + atomic_t rx_bufs_left[MAX_RX_RINGS]; spinlock_t tx_lock; @@ -558,27 +639,11 @@ typedef struct s2io_nic { u16 tx_err_count; u16 rx_err_count; -#ifndef CONFIG_S2IO_NAPI - /* Index to the absolute position of the put pointer of Rx ring. */ - int put_pos[MAX_RX_RINGS]; -#endif - - /* - * Place holders for the virtual and physical addresses of - * all the Rx Blocks - */ - rx_block_info_t rx_blocks[MAX_RX_RINGS][MAX_RX_BLOCKS_PER_RING]; - int block_count[MAX_RX_RINGS]; - int pkt_cnt[MAX_RX_RINGS]; - - /* Place holder of all the TX List's Phy and Virt addresses. */ - list_info_hold_t *list_info[MAX_TX_FIFOS]; - /* Id timer, used to blink NIC to physically identify NIC. */ struct timer_list id_timer; /* Restart timer, used to restart NIC if the device is stuck and - * a schedule task that will set the correct Link state once the + * a schedule task that will set the correct Link state once the * NIC's PHY has stabilized after a state change. */ #ifdef INIT_TQUEUE @@ -589,12 +654,12 @@ typedef struct s2io_nic { struct work_struct set_link_task; #endif - /* Flag that can be used to turn on or turn off the Rx checksum + /* Flag that can be used to turn on or turn off the Rx checksum * offload feature. */ int rx_csum; - /* after blink, the adapter must be restored with original + /* after blink, the adapter must be restored with original * values. */ u64 adapt_ctrl_org; @@ -604,16 +669,12 @@ typedef struct s2io_nic { #define LINK_DOWN 1 #define LINK_UP 2 -#ifdef CONFIG_2BUFF_MODE - /* Buffer Address store. */ - buffAdd_t **ba[MAX_RX_RINGS]; -#endif int task_flag; #define CARD_DOWN 1 #define CARD_UP 2 atomic_t card_state; volatile unsigned long link_state; -} nic_t; +}; #define RESET_ERROR 1; #define CMD_ERROR 2; @@ -622,9 +683,10 @@ typedef struct s2io_nic { #ifndef readq static inline u64 readq(void __iomem *addr) { - u64 ret = readl(addr + 4); - ret <<= 32; - ret |= readl(addr); + u64 ret = 0; + ret = readl(addr + 4); + (u64) ret <<= 32; + (u64) ret |= readl(addr); return ret; } @@ -637,10 +699,10 @@ static inline void writeq(u64 val, void __iomem *addr) writel((u32) (val >> 32), (addr + 4)); } -/* In 32 bit modes, some registers have to be written in a +/* In 32 bit modes, some registers have to be written in a * particular order to expect correct hardware operation. The - * macro SPECIAL_REG_WRITE is used to perform such ordered - * writes. Defines UF (Upper First) and LF (Lower First) will + * macro SPECIAL_REG_WRITE is used to perform such ordered + * writes. Defines UF (Upper First) and LF (Lower First) will * be used to specify the required write order. */ #define UF 1 @@ -716,6 +778,7 @@ static inline void SPECIAL_REG_WRITE(u64 val, void __iomem *addr, int order) #define PCC_FB_ECC_ERR vBIT(0xff, 16, 8) /* Interrupt to indicate PCC_FB_ECC Error. */ +#define RXD_GET_VLAN_TAG(Control_2) (u16)(Control_2 & MASK_VLAN_TAG) /* * Prototype declaration. */ @@ -725,36 +788,29 @@ static void __devexit s2io_rem_nic(struct pci_dev *pdev); static int init_shared_mem(struct s2io_nic *sp); static void free_shared_mem(struct s2io_nic *sp); static int init_nic(struct s2io_nic *nic); -#ifndef CONFIG_S2IO_NAPI -static void rx_intr_handler(struct s2io_nic *sp); -#endif -static void tx_intr_handler(struct s2io_nic *sp); +static void rx_intr_handler(ring_info_t *ring_data); +static void tx_intr_handler(fifo_info_t *fifo_data); static void alarm_intr_handler(struct s2io_nic *sp); static int s2io_starter(void); -static void s2io_closer(void); +void s2io_closer(void); static void s2io_tx_watchdog(struct net_device *dev); static void s2io_tasklet(unsigned long dev_addr); static void s2io_set_multicast(struct net_device *dev); -#ifndef CONFIG_2BUFF_MODE -static int rx_osm_handler(nic_t * sp, u16 len, RxD_t * rxdp, int ring_no); -#else -static int rx_osm_handler(nic_t * sp, RxD_t * rxdp, int ring_no, - buffAdd_t * ba); -#endif -static void s2io_link(nic_t * sp, int link); -static void s2io_reset(nic_t * sp); -#ifdef CONFIG_S2IO_NAPI +static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp); +void s2io_link(nic_t * sp, int link); +void s2io_reset(nic_t * sp); +#if defined(CONFIG_S2IO_NAPI) static int s2io_poll(struct net_device *dev, int *budget); #endif static void s2io_init_pci(nic_t * sp); -static int s2io_set_mac_addr(struct net_device *dev, u8 * addr); +int s2io_set_mac_addr(struct net_device *dev, u8 * addr); static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs); -static int verify_xena_quiescence(u64 val64, int flag); +static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag); static struct ethtool_ops netdev_ethtool_ops; static void s2io_set_link(unsigned long data); -static int s2io_set_swapper(nic_t * sp); -static void s2io_card_down(nic_t * nic); -static int s2io_card_up(nic_t * nic); - +int s2io_set_swapper(nic_t * sp); +static void s2io_card_down(nic_t *nic); +static int s2io_card_up(nic_t *nic); +int get_xena_rev_id(struct pci_dev *pdev); #endif /* _S2IO_H */ -- cgit v0.10.2 From 5e25b9ddb6683fe225a2266b53d73c57381a0c18 Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:27:09 -0700 Subject: [PATCH] S2io: Hardware fixes Hi, Below patch addresses few h/w specific issues. 1. Check for additional ownership bit on Rx path before starting Rx processing. 2. Enable only 4 PCCs(Per Context Controller) for Xframe I revisions less than 4. 3. Program Rx and Tx round robin registers depending on no. of rings/FIFOs. 4. Tx continous interrupts is now a loadable parameter. 5. Reset the card if we get double-bit ECC errors. 6. A soft reset of XGXS being done to force a link state change has been eliminated. 7. After a reset, clear "parity error detected" bit, PCI-X ECC status register, and PCI_STATUS bit in tx_pic_int register. 8. The error in the disabling allmulticast implementation has been rectified. 9. Leave the PCI-X parameters MMRBC, OST etc. at their BIOS/system defaults. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io-regs.h b/drivers/net/s2io-regs.h index 8746740..826deb0 100644 --- a/drivers/net/s2io-regs.h +++ b/drivers/net/s2io-regs.h @@ -62,6 +62,7 @@ typedef struct _XENA_dev_config { #define ADAPTER_STATUS_RMAC_REMOTE_FAULT BIT(6) #define ADAPTER_STATUS_RMAC_LOCAL_FAULT BIT(7) #define ADAPTER_STATUS_RMAC_PCC_IDLE vBIT(0xFF,8,8) +#define ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE vBIT(0x0F,8,8) #define ADAPTER_STATUS_RC_PRC_QUIESCENT vBIT(0xFF,16,8) #define ADAPTER_STATUS_MC_DRAM_READY BIT(24) #define ADAPTER_STATUS_MC_QUEUES_READY BIT(25) @@ -245,6 +246,7 @@ typedef struct _XENA_dev_config { #define STAT_TRSF_PER(n) TBD #define PER_SEC 0x208d5 #define SET_UPDT_PERIOD(n) vBIT((PER_SEC*n),32,32) +#define SET_UPDT_CLICKS(val) vBIT(val, 32, 32) u64 stat_addr; @@ -289,6 +291,7 @@ typedef struct _XENA_dev_config { u64 pcc_err_reg; #define PCC_FB_ECC_DB_ERR vBIT(0xFF, 16, 8) +#define PCC_ENABLE_FOUR vBIT(0x0F,0,8) u64 pcc_err_mask; u64 pcc_err_alarm; @@ -690,6 +693,10 @@ typedef struct _XENA_dev_config { #define MC_ERR_REG_MIRI_CRI_ERR_0 BIT(22) #define MC_ERR_REG_MIRI_CRI_ERR_1 BIT(23) #define MC_ERR_REG_SM_ERR BIT(31) +#define MC_ERR_REG_ECC_ALL_SNG (BIT(6) | \ + BIT(7) | BIT(17) | BIT(19)) +#define MC_ERR_REG_ECC_ALL_DBL (BIT(14) | \ + BIT(15) | BIT(18) | BIT(20)) u64 mc_err_mask; u64 mc_err_alarm; diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 0721e78..e2144fc 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -68,6 +68,16 @@ static char s2io_driver_name[] = "Neterion"; static char s2io_driver_version[] = "Version 1.7.7"; +static inline int RXD_IS_UP2DT(RxD_t *rxdp) +{ + int ret; + + ret = ((!(rxdp->Control_1 & RXD_OWN_XENA)) && + (GET_RXD_MARKER(rxdp->Control_2) != THE_RXD_MARK)); + + return ret; +} + /* * Cards with following subsystem_id have a link state indication * problem, 600B, 600C, 600D, 640B, 640C and 640D. @@ -230,6 +240,7 @@ static unsigned int rx_ring_sz[MAX_RX_RINGS] = static unsigned int Stats_refresh_time = 4; static unsigned int rts_frm_len[MAX_RX_RINGS] = {[0 ...(MAX_RX_RINGS - 1)] = 0 }; +static unsigned int use_continuous_tx_intrs = 1; static unsigned int rmac_pause_time = 65535; static unsigned int mc_pause_threshold_q0q3 = 187; static unsigned int mc_pause_threshold_q4q7 = 187; @@ -638,7 +649,7 @@ static int init_nic(struct s2io_nic *nic) mac_control = &nic->mac_control; config = &nic->config; - /* to set the swapper control on the card */ + /* to set the swapper controle on the card */ if(s2io_set_swapper(nic)) { DBG_PRINT(ERR_DBG,"ERROR: Setting Swapper failed\n"); return -1; @@ -756,6 +767,13 @@ static int init_nic(struct s2io_nic *nic) val64 |= BIT(0); /* To enable the FIFO partition. */ writeq(val64, &bar0->tx_fifo_partition_0); + /* + * Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug + * SXE-008 TRANSMIT DMA ARBITRATION ISSUE. + */ + if (get_xena_rev_id(nic->pdev) < 4) + writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable); + val64 = readq(&bar0->tx_fifo_partition_0); DBG_PRINT(INIT_DBG, "Fifo partition at: 0x%p is: 0x%llx\n", &bar0->tx_fifo_partition_0, (unsigned long long) val64); @@ -823,37 +841,250 @@ static int init_nic(struct s2io_nic *nic) } writeq(val64, &bar0->rx_queue_cfg); - /* Initializing the Tx round robin registers to 0 - * filling tx and rx round robin registers as per - * the number of FIFOs and Rings is still TODO - */ - writeq(0, &bar0->tx_w_round_robin_0); - writeq(0, &bar0->tx_w_round_robin_1); - writeq(0, &bar0->tx_w_round_robin_2); - writeq(0, &bar0->tx_w_round_robin_3); - writeq(0, &bar0->tx_w_round_robin_4); - /* - * TODO - * Disable Rx steering. Hard coding all packets to be steered to - * Queue 0 for now. + * Filling Tx round robin registers + * as per the number of FIFOs */ - val64 = 0x8080808080808080ULL; - writeq(val64, &bar0->rts_qos_steering); + switch (config->tx_fifo_num) { + case 1: + val64 = 0x0000000000000000ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + writeq(val64, &bar0->tx_w_round_robin_1); + writeq(val64, &bar0->tx_w_round_robin_2); + writeq(val64, &bar0->tx_w_round_robin_3); + writeq(val64, &bar0->tx_w_round_robin_4); + break; + case 2: + val64 = 0x0000010000010000ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + val64 = 0x0100000100000100ULL; + writeq(val64, &bar0->tx_w_round_robin_1); + val64 = 0x0001000001000001ULL; + writeq(val64, &bar0->tx_w_round_robin_2); + val64 = 0x0000010000010000ULL; + writeq(val64, &bar0->tx_w_round_robin_3); + val64 = 0x0100000000000000ULL; + writeq(val64, &bar0->tx_w_round_robin_4); + break; + case 3: + val64 = 0x0001000102000001ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + val64 = 0x0001020000010001ULL; + writeq(val64, &bar0->tx_w_round_robin_1); + val64 = 0x0200000100010200ULL; + writeq(val64, &bar0->tx_w_round_robin_2); + val64 = 0x0001000102000001ULL; + writeq(val64, &bar0->tx_w_round_robin_3); + val64 = 0x0001020000000000ULL; + writeq(val64, &bar0->tx_w_round_robin_4); + break; + case 4: + val64 = 0x0001020300010200ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + val64 = 0x0100000102030001ULL; + writeq(val64, &bar0->tx_w_round_robin_1); + val64 = 0x0200010000010203ULL; + writeq(val64, &bar0->tx_w_round_robin_2); + val64 = 0x0001020001000001ULL; + writeq(val64, &bar0->tx_w_round_robin_3); + val64 = 0x0203000100000000ULL; + writeq(val64, &bar0->tx_w_round_robin_4); + break; + case 5: + val64 = 0x0001000203000102ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + val64 = 0x0001020001030004ULL; + writeq(val64, &bar0->tx_w_round_robin_1); + val64 = 0x0001000203000102ULL; + writeq(val64, &bar0->tx_w_round_robin_2); + val64 = 0x0001020001030004ULL; + writeq(val64, &bar0->tx_w_round_robin_3); + val64 = 0x0001000000000000ULL; + writeq(val64, &bar0->tx_w_round_robin_4); + break; + case 6: + val64 = 0x0001020304000102ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + val64 = 0x0304050001020001ULL; + writeq(val64, &bar0->tx_w_round_robin_1); + val64 = 0x0203000100000102ULL; + writeq(val64, &bar0->tx_w_round_robin_2); + val64 = 0x0304000102030405ULL; + writeq(val64, &bar0->tx_w_round_robin_3); + val64 = 0x0001000200000000ULL; + writeq(val64, &bar0->tx_w_round_robin_4); + break; + case 7: + val64 = 0x0001020001020300ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + val64 = 0x0102030400010203ULL; + writeq(val64, &bar0->tx_w_round_robin_1); + val64 = 0x0405060001020001ULL; + writeq(val64, &bar0->tx_w_round_robin_2); + val64 = 0x0304050000010200ULL; + writeq(val64, &bar0->tx_w_round_robin_3); + val64 = 0x0102030000000000ULL; + writeq(val64, &bar0->tx_w_round_robin_4); + break; + case 8: + val64 = 0x0001020300040105ULL; + writeq(val64, &bar0->tx_w_round_robin_0); + val64 = 0x0200030106000204ULL; + writeq(val64, &bar0->tx_w_round_robin_1); + val64 = 0x0103000502010007ULL; + writeq(val64, &bar0->tx_w_round_robin_2); + val64 = 0x0304010002060500ULL; + writeq(val64, &bar0->tx_w_round_robin_3); + val64 = 0x0103020400000000ULL; + writeq(val64, &bar0->tx_w_round_robin_4); + break; + } + + /* Filling the Rx round robin registers as per the + * number of Rings and steering based on QoS. + */ + switch (config->rx_ring_num) { + case 1: + val64 = 0x8080808080808080ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + case 2: + val64 = 0x0000010000010000ULL; + writeq(val64, &bar0->rx_w_round_robin_0); + val64 = 0x0100000100000100ULL; + writeq(val64, &bar0->rx_w_round_robin_1); + val64 = 0x0001000001000001ULL; + writeq(val64, &bar0->rx_w_round_robin_2); + val64 = 0x0000010000010000ULL; + writeq(val64, &bar0->rx_w_round_robin_3); + val64 = 0x0100000000000000ULL; + writeq(val64, &bar0->rx_w_round_robin_4); + + val64 = 0x8080808040404040ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + case 3: + val64 = 0x0001000102000001ULL; + writeq(val64, &bar0->rx_w_round_robin_0); + val64 = 0x0001020000010001ULL; + writeq(val64, &bar0->rx_w_round_robin_1); + val64 = 0x0200000100010200ULL; + writeq(val64, &bar0->rx_w_round_robin_2); + val64 = 0x0001000102000001ULL; + writeq(val64, &bar0->rx_w_round_robin_3); + val64 = 0x0001020000000000ULL; + writeq(val64, &bar0->rx_w_round_robin_4); + + val64 = 0x8080804040402020ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + case 4: + val64 = 0x0001020300010200ULL; + writeq(val64, &bar0->rx_w_round_robin_0); + val64 = 0x0100000102030001ULL; + writeq(val64, &bar0->rx_w_round_robin_1); + val64 = 0x0200010000010203ULL; + writeq(val64, &bar0->rx_w_round_robin_2); + val64 = 0x0001020001000001ULL; + writeq(val64, &bar0->rx_w_round_robin_3); + val64 = 0x0203000100000000ULL; + writeq(val64, &bar0->rx_w_round_robin_4); + + val64 = 0x8080404020201010ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + case 5: + val64 = 0x0001000203000102ULL; + writeq(val64, &bar0->rx_w_round_robin_0); + val64 = 0x0001020001030004ULL; + writeq(val64, &bar0->rx_w_round_robin_1); + val64 = 0x0001000203000102ULL; + writeq(val64, &bar0->rx_w_round_robin_2); + val64 = 0x0001020001030004ULL; + writeq(val64, &bar0->rx_w_round_robin_3); + val64 = 0x0001000000000000ULL; + writeq(val64, &bar0->rx_w_round_robin_4); + + val64 = 0x8080404020201008ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + case 6: + val64 = 0x0001020304000102ULL; + writeq(val64, &bar0->rx_w_round_robin_0); + val64 = 0x0304050001020001ULL; + writeq(val64, &bar0->rx_w_round_robin_1); + val64 = 0x0203000100000102ULL; + writeq(val64, &bar0->rx_w_round_robin_2); + val64 = 0x0304000102030405ULL; + writeq(val64, &bar0->rx_w_round_robin_3); + val64 = 0x0001000200000000ULL; + writeq(val64, &bar0->rx_w_round_robin_4); + + val64 = 0x8080404020100804ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + case 7: + val64 = 0x0001020001020300ULL; + writeq(val64, &bar0->rx_w_round_robin_0); + val64 = 0x0102030400010203ULL; + writeq(val64, &bar0->rx_w_round_robin_1); + val64 = 0x0405060001020001ULL; + writeq(val64, &bar0->rx_w_round_robin_2); + val64 = 0x0304050000010200ULL; + writeq(val64, &bar0->rx_w_round_robin_3); + val64 = 0x0102030000000000ULL; + writeq(val64, &bar0->rx_w_round_robin_4); + + val64 = 0x8080402010080402ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + case 8: + val64 = 0x0001020300040105ULL; + writeq(val64, &bar0->rx_w_round_robin_0); + val64 = 0x0200030106000204ULL; + writeq(val64, &bar0->rx_w_round_robin_1); + val64 = 0x0103000502010007ULL; + writeq(val64, &bar0->rx_w_round_robin_2); + val64 = 0x0304010002060500ULL; + writeq(val64, &bar0->rx_w_round_robin_3); + val64 = 0x0103020400000000ULL; + writeq(val64, &bar0->rx_w_round_robin_4); + + val64 = 0x8040201008040201ULL; + writeq(val64, &bar0->rts_qos_steering); + break; + } /* UDP Fix */ val64 = 0; for (i = 0; i < 8; i++) writeq(val64, &bar0->rts_frm_len_n[i]); - /* Set the default rts frame length for ring0 */ - writeq(MAC_RTS_FRM_LEN_SET(dev->mtu+22), - &bar0->rts_frm_len_n[0]); + /* Set the default rts frame length for the rings configured */ + val64 = MAC_RTS_FRM_LEN_SET(dev->mtu+22); + for (i = 0 ; i < config->rx_ring_num ; i++) + writeq(val64, &bar0->rts_frm_len_n[i]); + + /* Set the frame length for the configured rings + * desired by the user + */ + for (i = 0; i < config->rx_ring_num; i++) { + /* If rts_frm_len[i] == 0 then it is assumed that user not + * specified frame length steering. + * If the user provides the frame length then program + * the rts_frm_len register for those values or else + * leave it as it is. + */ + if (rts_frm_len[i] != 0) { + writeq(MAC_RTS_FRM_LEN_SET(rts_frm_len[i]), + &bar0->rts_frm_len_n[i]); + } + } /* Program statistics memory */ writeq(mac_control->stats_mem_phy, &bar0->stat_addr); val64 = SET_UPDT_PERIOD(Stats_refresh_time) | - STAT_CFG_STAT_RO | STAT_CFG_STAT_EN; + STAT_CFG_STAT_RO | STAT_CFG_STAT_EN; writeq(val64, &bar0->stat_cfg); /* @@ -877,13 +1108,14 @@ static int init_nic(struct s2io_nic *nic) val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078) | TTI_DATA1_MEM_TX_URNG_A(0xA) | TTI_DATA1_MEM_TX_URNG_B(0x10) | - TTI_DATA1_MEM_TX_URNG_C(0x30) | TTI_DATA1_MEM_TX_TIMER_AC_EN | - TTI_DATA1_MEM_TX_TIMER_CI_EN; + TTI_DATA1_MEM_TX_URNG_C(0x30) | TTI_DATA1_MEM_TX_TIMER_AC_EN; + if (use_continuous_tx_intrs) + val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN; writeq(val64, &bar0->tti_data1_mem); val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) | TTI_DATA2_MEM_TX_UFC_B(0x20) | - TTI_DATA2_MEM_TX_UFC_C(0x40) | TTI_DATA2_MEM_TX_UFC_D(0x80); + TTI_DATA2_MEM_TX_UFC_C(0x70) | TTI_DATA2_MEM_TX_UFC_D(0x80); writeq(val64, &bar0->tti_data2_mem); val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD; @@ -927,10 +1159,11 @@ static int init_nic(struct s2io_nic *nic) writeq(val64, &bar0->rti_command_mem); /* - * Once the operation completes, the Strobe bit of the command - * register will be reset. We poll for this particular condition - * We wait for a maximum of 500ms for the operation to complete, - * if it's not complete by then we return error. + * Once the operation completes, the Strobe bit of the + * command register will be reset. We poll for this + * particular condition. We wait for a maximum of 500ms + * for the operation to complete, if it's not complete + * by then we return error. */ time = 0; while (TRUE) { @@ -1185,10 +1418,10 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); /* - * All MC block error interrupts are disabled for now. - * TODO + * Enable all MC Intrs. */ - writeq(DISABLE_ALL_INTRS, &bar0->mc_int_mask); + writeq(0x0, &bar0->mc_int_mask); + writeq(0x0, &bar0->mc_err_mask); } else if (flag == DISABLE_INTRS) { /* * Disable MC Intrs in the general intr mask register @@ -1247,23 +1480,41 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) } } -static int check_prc_pcc_state(u64 val64, int flag) +static int check_prc_pcc_state(u64 val64, int flag, int rev_id) { int ret = 0; if (flag == FALSE) { - if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) && - ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == - ADAPTER_STATUS_RC_PRC_QUIESCENT)) { - ret = 1; + if (rev_id >= 4) { + if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) && + ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == + ADAPTER_STATUS_RC_PRC_QUIESCENT)) { + ret = 1; + } + } else { + if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) && + ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == + ADAPTER_STATUS_RC_PRC_QUIESCENT)) { + ret = 1; + } } } else { - if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) == - ADAPTER_STATUS_RMAC_PCC_IDLE) && - (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) || - ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == - ADAPTER_STATUS_RC_PRC_QUIESCENT))) { - ret = 1; + if (rev_id >= 4) { + if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) == + ADAPTER_STATUS_RMAC_PCC_IDLE) && + (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) || + ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == + ADAPTER_STATUS_RC_PRC_QUIESCENT))) { + ret = 1; + } + } else { + if (((val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) == + ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) && + (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) || + ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == + ADAPTER_STATUS_RC_PRC_QUIESCENT))) { + ret = 1; + } } } @@ -1286,6 +1537,7 @@ static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag) { int ret = 0; u64 tmp64 = ~((u64) val64); + int rev_id = get_xena_rev_id(sp->pdev); if (! (tmp64 & @@ -1294,7 +1546,7 @@ static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag) ADAPTER_STATUS_PIC_QUIESCENT | ADAPTER_STATUS_MC_DRAM_READY | ADAPTER_STATUS_MC_QUEUES_READY | ADAPTER_STATUS_M_PLL_LOCK | ADAPTER_STATUS_P_PLL_LOCK))) { - ret = check_prc_pcc_state(val64, flag); + ret = check_prc_pcc_state(val64, flag, rev_id); } return ret; @@ -1407,7 +1659,7 @@ static int start_nic(struct s2io_nic *nic) /* Enable select interrupts */ interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR | - RX_MAC_INTR; + RX_MAC_INTR | MC_INTR; en_dis_able_nic_intrs(nic, interruptible, ENABLE_INTRS); /* @@ -1439,21 +1691,6 @@ static int start_nic(struct s2io_nic *nic) */ schedule_work(&nic->set_link_task); - /* - * Here we are performing soft reset on XGXS to - * force link down. Since link is already up, we will get - * link state change interrupt after this reset - */ - SPECIAL_REG_WRITE(0x80010515001E0000ULL, &bar0->dtx_control, UF); - val64 = readq(&bar0->dtx_control); - udelay(50); - SPECIAL_REG_WRITE(0x80010515001E00E0ULL, &bar0->dtx_control, UF); - val64 = readq(&bar0->dtx_control); - udelay(50); - SPECIAL_REG_WRITE(0x80070515001F00E4ULL, &bar0->dtx_control, UF); - val64 = readq(&bar0->dtx_control); - udelay(50); - return SUCCESS; } @@ -1524,7 +1761,7 @@ static void stop_nic(struct s2io_nic *nic) /* Disable all interrupts */ interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR | - RX_MAC_INTR; + RX_MAC_INTR | MC_INTR; en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS); /* Disable PRCs */ @@ -1737,6 +1974,7 @@ int fill_rx_buffers(struct s2io_nic *nic, int ring_no) off++; mac_control->rings[ring_no].rx_curr_put_info.offset = off; #endif + rxdp->Control_2 |= SET_RXD_MARKER; atomic_inc(&nic->rx_bufs_left[ring_no]); alloc_tab++; @@ -1965,11 +2203,8 @@ static void rx_intr_handler(ring_info_t *ring_data) put_offset = (put_block * (MAX_RXDS_PER_BLOCK + 1)) + put_info.offset; #endif - while ((!(rxdp->Control_1 & RXD_OWN_XENA)) && -#ifdef CONFIG_2BUFF_MODE - (!rxdp->Control_2 & BIT(0)) && -#endif - (((get_offset + 1) % ring_bufs) != put_offset)) { + while (RXD_IS_UP2DT(rxdp) && + (((get_offset + 1) % ring_bufs) != put_offset)) { skb = (struct sk_buff *) ((unsigned long)rxdp->Host_Control); if (skb == NULL) { DBG_PRINT(ERR_DBG, "%s: The skb is ", @@ -2153,6 +2388,21 @@ static void alarm_intr_handler(struct s2io_nic *nic) schedule_work(&nic->set_link_task); } + /* Handling Ecc errors */ + val64 = readq(&bar0->mc_err_reg); + writeq(val64, &bar0->mc_err_reg); + if (val64 & (MC_ERR_REG_ECC_ALL_SNG | MC_ERR_REG_ECC_ALL_DBL)) { + if (val64 & MC_ERR_REG_ECC_ALL_DBL) { + DBG_PRINT(ERR_DBG, "%s: Device indicates ", + dev->name); + DBG_PRINT(ERR_DBG, "double ECC error!!\n"); + netif_stop_queue(dev); + schedule_work(&nic->rst_timer_task); + } else { + /* Device can recover from Single ECC errors */ + } + } + /* In case of a serious error, the device will be Reset. */ val64 = readq(&bar0->serr_source); if (val64 & SERR_SOURCE_ANY) { @@ -2226,7 +2476,7 @@ void s2io_reset(nic_t * sp) { XENA_dev_config_t __iomem *bar0 = sp->bar0; u64 val64; - u16 subid; + u16 subid, pci_cmd; val64 = SW_RESET_ALL; writeq(val64, &bar0->sw_reset); @@ -2255,6 +2505,18 @@ void s2io_reset(nic_t * sp) /* Set swapper to enable I/O register access */ s2io_set_swapper(sp); + /* Clear certain PCI/PCI-X fields after reset */ + pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd); + pci_cmd &= 0x7FFF; /* Clear parity err detect bit */ + pci_write_config_word(sp->pdev, PCI_COMMAND, pci_cmd); + + val64 = readq(&bar0->txpic_int_reg); + val64 &= ~BIT(62); /* Clearing PCI_STATUS error reflected here */ + writeq(val64, &bar0->txpic_int_reg); + + /* Clearing PCIX Ecc status register */ + pci_write_config_dword(sp->pdev, 0x68, 0); + /* Reset device statistics maintained by OS */ memset(&sp->stats, 0, sizeof (struct net_device_stats)); @@ -2797,6 +3059,8 @@ static void s2io_set_multicast(struct net_device *dev) /* Disable all Multicast addresses */ writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr), &bar0->rmac_addr_data0_mem); + writeq(RMAC_ADDR_DATA1_MEM_MASK(0x0), + &bar0->rmac_addr_data1_mem); val64 = RMAC_ADDR_CMD_MEM_WE | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD | RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos); @@ -4369,21 +4633,6 @@ static void s2io_init_pci(nic_t * sp) (pci_cmd | PCI_COMMAND_PARITY)); pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd); - /* Set MMRB count to 1024 in PCI-X Command register. */ - pcix_cmd &= 0xFFF3; - pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - (pcix_cmd | (0x1 << 2))); /* MMRBC 1K */ - pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - &(pcix_cmd)); - - /* Setting Maximum outstanding splits based on system type. */ - pcix_cmd &= 0xFF8F; - pcix_cmd |= XENA_MAX_OUTSTANDING_SPLITS(0x1); /* 2 splits. */ - pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - pcix_cmd); - pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, - &(pcix_cmd)); - /* Forcibly disabling relaxed ordering capability of the card. */ pcix_cmd &= 0xfffd; pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, @@ -4400,6 +4649,7 @@ module_param_array(tx_fifo_len, uint, NULL, 0); module_param_array(rx_ring_sz, uint, NULL, 0); module_param(Stats_refresh_time, int, 0); module_param_array(rts_frm_len, uint, NULL, 0); +module_param(use_continuous_tx_intrs, int, 1); module_param(rmac_pause_time, int, 0); module_param(mc_pause_threshold_q0q3, int, 0); module_param(mc_pause_threshold_q4q7, int, 0); diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index 4d2fc7a..92db59a 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -372,6 +372,10 @@ typedef struct _RxD_t { #define RXD_GET_L4_CKSUM(val) ((u16)(val) & 0xFFFF) u64 Control_2; +#define THE_RXD_MARK 0x3 +#define SET_RXD_MARKER vBIT(THE_RXD_MARK, 0, 2) +#define GET_RXD_MARKER(ctrl) ((ctrl & SET_RXD_MARKER) >> 62) + #ifndef CONFIG_2BUFF_MODE #define MASK_BUFFER0_SIZE vBIT(0x3FFF,2,14) #define SET_BUFFER0_SIZE(val) vBIT(val,2,14) -- cgit v0.10.2 From 7ba013ac029513eb4b70cfcd4b86e37c5f16c483 Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:29:20 -0700 Subject: [PATCH] S2io: Software fixes Hi, Below patch includes fixes for few purely software bugs identified since last release. 1. Keep track and display(as part of ethtool command output) the no. of single-bit and double-bit ECC errors. 2. Handle race condition between intr handler and "interface down" routine. 3. Initial link state setting modified so that the link state displayed after "interface Up" is correct. 4. Fix for "Incorrect Tx packet count when TSO is enabled". 5. Disable periodic DMA of statistics and schedule one-shot DMA only when required. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index e2144fc..e24c5e5 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -158,6 +158,9 @@ static char ethtool_stats_keys[][ETH_GSTRING_LEN] = { {"rmac_pause_cnt"}, {"rmac_accepted_ip"}, {"rmac_err_tcp"}, + {"\n DRIVER STATISTICS"}, + {"single_bit_ecc_errs"}, + {"double_bit_ecc_errs"}, }; #define S2IO_STAT_LEN sizeof(ethtool_stats_keys)/ ETH_GSTRING_LEN @@ -237,7 +240,6 @@ static unsigned int tx_fifo_len[MAX_TX_FIFOS] = static unsigned int rx_ring_num = 1; static unsigned int rx_ring_sz[MAX_RX_RINGS] = {[0 ...(MAX_RX_RINGS - 1)] = 0 }; -static unsigned int Stats_refresh_time = 4; static unsigned int rts_frm_len[MAX_RX_RINGS] = {[0 ...(MAX_RX_RINGS - 1)] = 0 }; static unsigned int use_continuous_tx_intrs = 1; @@ -1083,9 +1085,6 @@ static int init_nic(struct s2io_nic *nic) /* Program statistics memory */ writeq(mac_control->stats_mem_phy, &bar0->stat_addr); - val64 = SET_UPDT_PERIOD(Stats_refresh_time) | - STAT_CFG_STAT_RO | STAT_CFG_STAT_EN; - writeq(val64, &bar0->stat_cfg); /* * Initializing the sampling rate for the device to calculate the @@ -2101,6 +2100,7 @@ static int s2io_poll(struct net_device *dev, int *budget) u64 val64; int i; + atomic_inc(&nic->isr_cnt); mac_control = &nic->mac_control; config = &nic->config; @@ -2136,6 +2136,7 @@ static int s2io_poll(struct net_device *dev, int *budget) } /* Re enable the Rx interrupts. */ en_dis_able_nic_intrs(nic, RX_TRAFFIC_INTR, ENABLE_INTRS); + atomic_dec(&nic->isr_cnt); return 0; no_rx: @@ -2149,6 +2150,7 @@ no_rx: break; } } + atomic_dec(&nic->isr_cnt); return 1; } #endif @@ -2179,6 +2181,13 @@ static void rx_intr_handler(ring_info_t *ring_data) #endif register u64 val64; + spin_lock(&nic->rx_lock); + if (atomic_read(&nic->card_state) == CARD_DOWN) { + DBG_PRINT(ERR_DBG, "%s: %s going down for reset\n", + __FUNCTION__, dev->name); + spin_unlock(&nic->rx_lock); + } + /* * rx_traffic_int reg is an R1 register, hence we read and write * back the same value in the register to clear it @@ -2210,6 +2219,7 @@ static void rx_intr_handler(ring_info_t *ring_data) DBG_PRINT(ERR_DBG, "%s: The skb is ", dev->name); DBG_PRINT(ERR_DBG, "Null in Rx Intr\n"); + spin_unlock(&nic->rx_lock); return; } #ifndef CONFIG_2BUFF_MODE @@ -2262,6 +2272,7 @@ static void rx_intr_handler(ring_info_t *ring_data) break; #endif } + spin_unlock(&nic->rx_lock); } /** @@ -2345,7 +2356,6 @@ static void tx_intr_handler(fifo_info_t *fifo_data) (sizeof(TxD_t) * fifo_data->max_txds)); /* Updating the statistics block */ - nic->stats.tx_packets++; nic->stats.tx_bytes += skb->len; dev_kfree_skb_irq(skb); @@ -2393,13 +2403,16 @@ static void alarm_intr_handler(struct s2io_nic *nic) writeq(val64, &bar0->mc_err_reg); if (val64 & (MC_ERR_REG_ECC_ALL_SNG | MC_ERR_REG_ECC_ALL_DBL)) { if (val64 & MC_ERR_REG_ECC_ALL_DBL) { + nic->mac_control.stats_info->sw_stat. + double_ecc_errs++; DBG_PRINT(ERR_DBG, "%s: Device indicates ", dev->name); DBG_PRINT(ERR_DBG, "double ECC error!!\n"); netif_stop_queue(dev); schedule_work(&nic->rst_timer_task); } else { - /* Device can recover from Single ECC errors */ + nic->mac_control.stats_info->sw_stat. + single_ecc_errs++; } } @@ -2695,7 +2708,7 @@ int s2io_open(struct net_device *dev) * Nic is initialized */ netif_carrier_off(dev); - sp->last_link_state = LINK_DOWN; + sp->last_link_state = 0; /* Unkown link state */ /* Initialize H/W and enable interrupts */ if (s2io_card_up(sp)) { @@ -2909,6 +2922,7 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) mac_info_t *mac_control; struct config_param *config; + atomic_inc(&sp->isr_cnt); mac_control = &sp->mac_control; config = &sp->config; @@ -2924,6 +2938,7 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) if (!reason) { /* The interrupt was not raised by Xena. */ + atomic_dec(&sp->isr_cnt); return IRQ_NONE; } @@ -2972,6 +2987,7 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) dev->name); DBG_PRINT(ERR_DBG, " in ISR!!\n"); clear_bit(0, (&sp->tasklet_status)); + atomic_dec(&sp->isr_cnt); return IRQ_HANDLED; } clear_bit(0, (&sp->tasklet_status)); @@ -2981,10 +2997,37 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) } #endif + atomic_dec(&sp->isr_cnt); return IRQ_HANDLED; } /** + * s2io_updt_stats - + */ +static void s2io_updt_stats(nic_t *sp) +{ + XENA_dev_config_t __iomem *bar0 = sp->bar0; + u64 val64; + int cnt = 0; + + if (atomic_read(&sp->card_state) == CARD_UP) { + /* Apprx 30us on a 133 MHz bus */ + val64 = SET_UPDT_CLICKS(10) | + STAT_CFG_ONE_SHOT_EN | STAT_CFG_STAT_EN; + writeq(val64, &bar0->stat_cfg); + do { + udelay(100); + val64 = readq(&bar0->stat_cfg); + if (!(val64 & BIT(0))) + break; + cnt++; + if (cnt == 5) + break; /* Updt failed */ + } while(1); + } +} + +/** * s2io_get_stats - Updates the device statistics structure. * @dev : pointer to the device structure. * Description: @@ -3004,6 +3047,11 @@ struct net_device_stats *s2io_get_stats(struct net_device *dev) mac_control = &sp->mac_control; config = &sp->config; + /* Configure Stats for immediate updt */ + s2io_updt_stats(sp); + + sp->stats.tx_packets = + le32_to_cpu(mac_control->stats_info->tmac_frms); sp->stats.tx_errors = le32_to_cpu(mac_control->stats_info->tmac_any_err_frms); sp->stats.rx_errors = @@ -4018,6 +4066,7 @@ static void s2io_get_ethtool_stats(struct net_device *dev, nic_t *sp = dev->priv; StatInfo_t *stat_info = sp->mac_control.stats_info; + s2io_updt_stats(sp); tmp_stats[i++] = le32_to_cpu(stat_info->tmac_frms); tmp_stats[i++] = le32_to_cpu(stat_info->tmac_data_octets); tmp_stats[i++] = le64_to_cpu(stat_info->tmac_drop_frms); @@ -4057,6 +4106,9 @@ static void s2io_get_ethtool_stats(struct net_device *dev, tmp_stats[i++] = le32_to_cpu(stat_info->rmac_pause_cnt); tmp_stats[i++] = le32_to_cpu(stat_info->rmac_accepted_ip); tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp); + tmp_stats[i++] = 0; + tmp_stats[i++] = stat_info->sw_stat.single_ecc_errs; + tmp_stats[i++] = stat_info->sw_stat.double_ecc_errs; } int s2io_ethtool_get_regs_len(struct net_device *dev) @@ -4353,14 +4405,27 @@ static void s2io_card_down(nic_t * sp) break; } } while (1); - spin_lock_irqsave(&sp->tx_lock, flags); s2io_reset(sp); - /* Free all unused Tx and Rx buffers */ + /* Waiting till all Interrupt handlers are complete */ + cnt = 0; + do { + msleep(10); + if (!atomic_read(&sp->isr_cnt)) + break; + cnt++; + } while(cnt < 5); + + spin_lock_irqsave(&sp->tx_lock, flags); + /* Free all Tx buffers */ free_tx_buffers(sp); + spin_unlock_irqrestore(&sp->tx_lock, flags); + + /* Free all Rx buffers */ + spin_lock_irqsave(&sp->rx_lock, flags); free_rx_buffers(sp); + spin_unlock_irqrestore(&sp->rx_lock, flags); - spin_unlock_irqrestore(&sp->tx_lock, flags); clear_bit(0, &(sp->link_state)); } @@ -4647,7 +4712,6 @@ module_param(tx_fifo_num, int, 0); module_param(rx_ring_num, int, 0); module_param_array(tx_fifo_len, uint, NULL, 0); module_param_array(rx_ring_sz, uint, NULL, 0); -module_param(Stats_refresh_time, int, 0); module_param_array(rts_frm_len, uint, NULL, 0); module_param(use_continuous_tx_intrs, int, 1); module_param(rmac_pause_time, int, 0); @@ -4804,6 +4868,9 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) for (i = 0; i < config->rx_ring_num; i++) atomic_set(&sp->rx_bufs_left[i], 0); + /* Initialize the number of ISRs currently running */ + atomic_set(&sp->isr_cnt, 0); + /* initialize the shared memory used by the NIC and the host */ if (init_shared_mem(sp)) { DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n", @@ -4938,6 +5005,7 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) #ifndef CONFIG_S2IO_NAPI spin_lock_init(&sp->put_lock); #endif + spin_lock_init(&sp->rx_lock); /* * SXE-002: Configure link and activity LED to init state @@ -4961,13 +5029,16 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) goto register_failed; } + /* Initialize device name */ + strcpy(sp->name, dev->name); + strcat(sp->name, ": Neterion Xframe I 10GbE adapter"); + /* * Make Link state as off at this point, when the Link change * interrupt comes the state will be automatically changed to * the right state. */ netif_carrier_off(dev); - sp->last_link_state = LINK_DOWN; return 0; diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index 92db59a..69dd0e5 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -195,6 +195,9 @@ typedef struct stat_block { u32 rxd_rd_cnt; u32 rxf_wr_cnt; u32 txf_rd_cnt; + +/* Software statistics maintained by driver */ + swStat_t sw_stat; } StatInfo_t; /* @@ -678,6 +681,8 @@ struct s2io_nic { #define CARD_UP 2 atomic_t card_state; volatile unsigned long link_state; + spinlock_t rx_lock; + atomic_t isr_cnt; }; #define RESET_ERROR 1; -- cgit v0.10.2 From 1ddc50d40a19b3524d302d1d6bfd52ac7bc6b6f7 Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:30:43 -0700 Subject: [PATCH] S2io: Removed memory leaks Hi, This patch fixes certain memory leaks discovered in free_tx_buffers() and rx_osm_handler() Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index e24c5e5..6668b99 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -1709,7 +1709,7 @@ static void free_tx_buffers(struct s2io_nic *nic) int i, j; mac_info_t *mac_control; struct config_param *config; - int cnt = 0; + int cnt = 0, frg_cnt; mac_control = &nic->mac_control; config = &nic->config; @@ -1722,11 +1722,33 @@ static void free_tx_buffers(struct s2io_nic *nic) (struct sk_buff *) ((unsigned long) txdp-> Host_Control); if (skb == NULL) { - memset(txdp, 0, sizeof(TxD_t)); + memset(txdp, 0, sizeof(TxD_t) * + config->max_txds); continue; } + frg_cnt = skb_shinfo(skb)->nr_frags; + pci_unmap_single(nic->pdev, (dma_addr_t) + txdp->Buffer_Pointer, + skb->len - skb->data_len, + PCI_DMA_TODEVICE); + if (frg_cnt) { + TxD_t *temp; + temp = txdp; + txdp++; + for (j = 0; j < frg_cnt; j++, txdp++) { + skb_frag_t *frag = + &skb_shinfo(skb)->frags[j]; + pci_unmap_page(nic->pdev, + (dma_addr_t) + txdp-> + Buffer_Pointer, + frag->size, + PCI_DMA_TODEVICE); + } + txdp = temp; + } dev_kfree_skb(skb); - memset(txdp, 0, sizeof(TxD_t)); + memset(txdp, 0, sizeof(TxD_t) * config->max_txds); cnt++; } DBG_PRINT(INTR_DBG, @@ -4570,6 +4592,11 @@ static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp) unsigned long long err = rxdp->Control_1 & RXD_T_CODE; DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%llx\n", dev->name, err); + dev_kfree_skb(skb); + sp->stats.rx_crc_errors++; + atomic_dec(&sp->rx_bufs_left[ring_no]); + rxdp->Host_Control = 0; + return 0; } /* Updating statistics */ -- cgit v0.10.2 From fe113638328995b69d8797e6466b29661b1602d1 Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:32:00 -0700 Subject: [PATCH] S2io: Performance improvements Hi, This patch relates to mostly performance related changes. 1. Fixed incorrect computation of PANIC level in rx_buffer_level(). 2. Removed unnecessary PIOs(read/write of tx_traffic_int and rx_traffic_int) from interrupt handler and removed read of general_int_status register from xmit routine. 3. Enable two-buffer mode(for Rx path) automatically for SGI systems. This improves Rx performance dramatically on SGI systems. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 6668b99..28d6d374 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -100,8 +100,7 @@ static inline int rx_buffer_level(nic_t * sp, int rxb_size, int ring) mac_control = &sp->mac_control; if ((mac_control->rings[ring].pkt_cnt - rxb_size) > 16) { level = LOW; - if ((mac_control->rings[ring].pkt_cnt - rxb_size) < - MAX_RXDS_PER_BLOCK) { + if (rxb_size <= MAX_RXDS_PER_BLOCK) { level = PANIC; } } @@ -2193,7 +2192,6 @@ static void rx_intr_handler(ring_info_t *ring_data) { nic_t *nic = ring_data->nic; struct net_device *dev = (struct net_device *) nic->dev; - XENA_dev_config_t __iomem *bar0 = nic->bar0; int get_block, get_offset, put_block, put_offset, ring_bufs; rx_curr_get_info_t get_info, put_info; RxD_t *rxdp; @@ -2201,8 +2199,6 @@ static void rx_intr_handler(ring_info_t *ring_data) #ifndef CONFIG_S2IO_NAPI int pkt_cnt = 0; #endif - register u64 val64; - spin_lock(&nic->rx_lock); if (atomic_read(&nic->card_state) == CARD_DOWN) { DBG_PRINT(ERR_DBG, "%s: %s going down for reset\n", @@ -2210,13 +2206,6 @@ static void rx_intr_handler(ring_info_t *ring_data) spin_unlock(&nic->rx_lock); } - /* - * rx_traffic_int reg is an R1 register, hence we read and write - * back the same value in the register to clear it - */ - val64 = readq(&bar0->tx_traffic_int); - writeq(val64, &bar0->tx_traffic_int); - get_info = ring_data->rx_curr_get_info; get_block = get_info.block_index; put_info = ring_data->rx_curr_put_info; @@ -2312,20 +2301,11 @@ static void rx_intr_handler(ring_info_t *ring_data) static void tx_intr_handler(fifo_info_t *fifo_data) { nic_t *nic = fifo_data->nic; - XENA_dev_config_t __iomem *bar0 = nic->bar0; struct net_device *dev = (struct net_device *) nic->dev; tx_curr_get_info_t get_info, put_info; struct sk_buff *skb; TxD_t *txdlp; u16 j, frg_cnt; - register u64 val64 = 0; - - /* - * tx_traffic_int reg is an R1 register, hence we read and write - * back the same value in the register to clear it - */ - val64 = readq(&bar0->tx_traffic_int); - writeq(val64, &bar0->tx_traffic_int); get_info = fifo_data->tx_curr_get_info; put_info = fifo_data->tx_curr_put_info; @@ -2818,7 +2798,6 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) #endif mac_info_t *mac_control; struct config_param *config; - XENA_dev_config_t __iomem *bar0 = sp->bar0; mac_control = &sp->mac_control; config = &sp->config; @@ -2870,7 +2849,6 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) } txdp->Control_2 |= config->tx_intr_type; - txdp->Control_1 |= (TXD_BUFFER0_SIZE(frg_len) | TXD_GATHER_CODE_FIRST); txdp->Control_1 |= TXD_LIST_OWN_XENA; @@ -2890,6 +2868,8 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) val64 = mac_control->fifos[queue].list_info[put_off].list_phy_addr; writeq(val64, &tx_fifo->TxDL_Pointer); + wmb(); + val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST | TX_FIFO_LAST_LIST); @@ -2899,9 +2879,6 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) #endif writeq(val64, &tx_fifo->List_Control); - /* Perform a PCI read to flush previous writes */ - val64 = readq(&bar0->general_int_status); - put_off++; put_off %= mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1; mac_control->fifos[queue].tx_curr_put_info.offset = put_off; @@ -2940,7 +2917,7 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) nic_t *sp = dev->priv; XENA_dev_config_t __iomem *bar0 = sp->bar0; int i; - u64 reason = 0; + u64 reason = 0, val64; mac_info_t *mac_control; struct config_param *config; @@ -2978,6 +2955,13 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) #else /* If Intr is because of Rx Traffic */ if (reason & GEN_INTR_RXTRAFFIC) { + /* + * rx_traffic_int reg is an R1 register, writing all 1's + * will ensure that the actual interrupt causing bit get's + * cleared and hence a read can be avoided. + */ + val64 = 0xFFFFFFFFFFFFFFFFULL; + writeq(val64, &bar0->rx_traffic_int); for (i = 0; i < config->rx_ring_num; i++) { rx_intr_handler(&mac_control->rings[i]); } @@ -2986,6 +2970,14 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) /* If Intr is because of Tx Traffic */ if (reason & GEN_INTR_TXTRAFFIC) { + /* + * tx_traffic_int reg is an R1 register, writing all 1's + * will ensure that the actual interrupt causing bit get's + * cleared and hence a read can be avoided. + */ + val64 = 0xFFFFFFFFFFFFFFFFULL; + writeq(val64, &bar0->tx_traffic_int); + for (i = 0; i < config->tx_fifo_num; i++) tx_intr_handler(&mac_control->fifos[i]); } diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index 69dd0e5..ce9bf6d 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -13,6 +13,11 @@ #ifndef _S2IO_H #define _S2IO_H +/* Enable 2 buffer mode by default for SGI system */ +#ifdef CONFIG_IA64_SGI_SN2 +#define CONFIG_2BUFF_MODE +#endif + #define TBD 0 #define BIT(loc) (0x8000000000000000ULL >> (loc)) #define vBIT(val, loc, sz) (((u64)val) << (64-loc-sz)) -- cgit v0.10.2 From d8892c6ee39614bc6d282dbef0ff9fa461a6467c Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:33:12 -0700 Subject: [PATCH] S2io: Support for runtime MTU change Hi, Patch below supports MTU change on-the-fly(without bringing interface down) Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 28d6d374..aff1fb7 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -2849,6 +2849,7 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) } txdp->Control_2 |= config->tx_intr_type; + txdp->Control_1 |= (TXD_BUFFER0_SIZE(frg_len) | TXD_GATHER_CODE_FIRST); txdp->Control_1 |= TXD_LIST_OWN_XENA; @@ -4246,14 +4247,6 @@ int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) int s2io_change_mtu(struct net_device *dev, int new_mtu) { nic_t *sp = dev->priv; - XENA_dev_config_t __iomem *bar0 = sp->bar0; - register u64 val64; - - if (netif_running(dev)) { - DBG_PRINT(ERR_DBG, "%s: Must be stopped to ", dev->name); - DBG_PRINT(ERR_DBG, "change its MTU\n"); - return -EBUSY; - } if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) { DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n", @@ -4261,11 +4254,22 @@ int s2io_change_mtu(struct net_device *dev, int new_mtu) return -EPERM; } - /* Set the new MTU into the PYLD register of the NIC */ - val64 = new_mtu; - writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len); - dev->mtu = new_mtu; + if (netif_running(dev)) { + s2io_card_down(sp); + netif_stop_queue(dev); + if (s2io_card_up(sp)) { + DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n", + __FUNCTION__); + } + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + } else { /* Device is down */ + XENA_dev_config_t __iomem *bar0 = sp->bar0; + u64 val64 = new_mtu; + + writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len); + } return 0; } -- cgit v0.10.2 From 25fff88eb7dbc63e03f1766e130515900d440dbb Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:34:11 -0700 Subject: [PATCH] S2io: Timer based slowpath handling Hi, This patch implements the slow-path handling functions(link state change, hardware errors) as a timer. It is not handled in interrupt handler as was done previously. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index aff1fb7..ee498d2 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -168,6 +168,12 @@ static char ethtool_stats_keys[][ETH_GSTRING_LEN] = { #define S2IO_TEST_LEN sizeof(s2io_gstrings) / ETH_GSTRING_LEN #define S2IO_STRINGS_LEN S2IO_TEST_LEN * ETH_GSTRING_LEN +#define S2IO_TIMER_CONF(timer, handle, arg, exp) \ + init_timer(&timer); \ + timer.function = handle; \ + timer.data = (unsigned long) arg; \ + mod_timer(&timer, (jiffies + exp)) \ + /* * Constants to be programmed into the Xena's registers, to configure * the XAUI. @@ -2741,6 +2747,7 @@ int s2io_open(struct net_device *dev) setting_mac_address_failed: free_irq(sp->pdev->irq, dev); isr_registration_failed: + del_timer_sync(&sp->alarm_timer); s2io_reset(sp); hw_init_failed: return err; @@ -2898,6 +2905,15 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) return 0; } +static void +s2io_alarm_handle(unsigned long data) +{ + nic_t *sp = (nic_t *)data; + + alarm_intr_handler(sp); + mod_timer(&sp->alarm_timer, jiffies + HZ / 2); +} + /** * s2io_isr - ISR handler of the device . * @irq: the irq of the device. @@ -2942,9 +2958,6 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) return IRQ_NONE; } - if (reason & (GEN_ERROR_INTR)) - alarm_intr_handler(sp); - #ifdef CONFIG_S2IO_NAPI if (reason & GEN_INTR_RXTRAFFIC) { if (netif_rx_schedule_prep(dev)) { @@ -4394,6 +4407,7 @@ static void s2io_card_down(nic_t * sp) unsigned long flags; register u64 val64 = 0; + del_timer_sync(&sp->alarm_timer); /* If s2io_set_link task is executing, wait till it completes. */ while (test_and_set_bit(0, &(sp->link_state))) { msleep(50); @@ -4496,6 +4510,8 @@ static int s2io_card_up(nic_t * sp) return -ENODEV; } + S2IO_TIMER_CONF(sp->alarm_timer, s2io_alarm_handle, sp, (HZ/2)); + atomic_set(&sp->card_state, CARD_UP); return 0; } diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index ce9bf6d..263fe7a 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -624,6 +624,9 @@ struct s2io_nic { struct tasklet_struct task; volatile unsigned long tasklet_status; + /* Timer that handles I/O errors/exceptions */ + struct timer_list alarm_timer; + /* Space to back up the PCI config space */ u32 config_space[256 / sizeof(u32)]; @@ -819,6 +822,7 @@ static int s2io_poll(struct net_device *dev, int *budget); #endif static void s2io_init_pci(nic_t * sp); int s2io_set_mac_addr(struct net_device *dev, u8 * addr); +static void s2io_alarm_handle(unsigned long data); static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs); static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag); static struct ethtool_ops netdev_ethtool_ops; -- cgit v0.10.2 From be3a6b02eb68a4d47397b771b6e4aa1f7f0f7ffb Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:35:55 -0700 Subject: [PATCH] S2io: VLAN support Hi, Patch below adds VLAN support to the driver. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index ee498d2..db3e394 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -55,6 +55,7 @@ #include #include #include +#include #include #include @@ -174,6 +175,30 @@ static char ethtool_stats_keys[][ETH_GSTRING_LEN] = { timer.data = (unsigned long) arg; \ mod_timer(&timer, (jiffies + exp)) \ +/* Add the vlan */ +static void s2io_vlan_rx_register(struct net_device *dev, + struct vlan_group *grp) +{ + nic_t *nic = dev->priv; + unsigned long flags; + + spin_lock_irqsave(&nic->tx_lock, flags); + nic->vlgrp = grp; + spin_unlock_irqrestore(&nic->tx_lock, flags); +} + +/* Unregister the vlan */ +static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid) +{ + nic_t *nic = dev->priv; + unsigned long flags; + + spin_lock_irqsave(&nic->tx_lock, flags); + if (nic->vlgrp) + nic->vlgrp->vlan_devices[vid] = NULL; + spin_unlock_irqrestore(&nic->tx_lock, flags); +} + /* * Constants to be programmed into the Xena's registers, to configure * the XAUI. @@ -2803,6 +2828,8 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) #ifdef NETIF_F_TSO int mss; #endif + u16 vlan_tag = 0; + int vlan_priority = 0; mac_info_t *mac_control; struct config_param *config; @@ -2821,6 +2848,13 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) queue = 0; + /* Get Fifo number to Transmit based on vlan priority */ + if (sp->vlgrp && vlan_tx_tag_present(skb)) { + vlan_tag = vlan_tx_tag_get(skb); + vlan_priority = vlan_tag >> 13; + queue = config->fifo_mapping[vlan_priority]; + } + put_off = (u16) mac_control->fifos[queue].tx_curr_put_info.offset; get_off = (u16) mac_control->fifos[queue].tx_curr_get_info.offset; txdp = (TxD_t *) mac_control->fifos[queue].list_info[put_off]. @@ -2857,6 +2891,11 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) txdp->Control_2 |= config->tx_intr_type; + if (sp->vlgrp && vlan_tx_tag_present(skb)) { + txdp->Control_2 |= TXD_VLAN_ENABLE; + txdp->Control_2 |= TXD_VLAN_TAG(vlan_tag); + } + txdp->Control_1 |= (TXD_BUFFER0_SIZE(frg_len) | TXD_GATHER_CODE_FIRST); txdp->Control_1 |= TXD_LIST_OWN_XENA; @@ -4653,10 +4692,23 @@ static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp) skb->protocol = eth_type_trans(skb, dev); #ifdef CONFIG_S2IO_NAPI - netif_receive_skb(skb); + if (sp->vlgrp && RXD_GET_VLAN_TAG(rxdp->Control_2)) { + /* Queueing the vlan frame to the upper layer */ + vlan_hwaccel_receive_skb(skb, sp->vlgrp, + RXD_GET_VLAN_TAG(rxdp->Control_2)); + } else { + netif_receive_skb(skb); + } #else - netif_rx(skb); + if (sp->vlgrp && RXD_GET_VLAN_TAG(rxdp->Control_2)) { + /* Queueing the vlan frame to the upper layer */ + vlan_hwaccel_rx(skb, sp->vlgrp, + RXD_GET_VLAN_TAG(rxdp->Control_2)); + } else { + netif_rx(skb); + } #endif + dev->last_rx = jiffies; atomic_dec(&sp->rx_bufs_left[ring_no]); return SUCCESS; @@ -4954,6 +5006,9 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) dev->do_ioctl = &s2io_ioctl; dev->change_mtu = &s2io_change_mtu; SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops); + dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; + dev->vlan_rx_register = s2io_vlan_rx_register; + dev->vlan_rx_kill_vid = (void *)s2io_vlan_rx_kill_vid; /* * will use eth_mac_addr() for dev->set_mac_address diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index 263fe7a..b924ef2 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -689,6 +689,8 @@ struct s2io_nic { #define CARD_UP 2 atomic_t card_state; volatile unsigned long link_state; + struct vlan_group *vlgrp; + spinlock_t rx_lock; atomic_t isr_cnt; }; -- cgit v0.10.2 From 541ae68f6ddf1c27aa6879935ce541f110484202 Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:36:55 -0700 Subject: [PATCH] S2io: Support for Xframe II NIC Hi, This patch provides basic support for the Xframe II adapter. Includes the following changes: 1. New values to program XAUI interface. 2. Print the PCI/PCI-X mode(bus frequency, width). 3. Remove EOI from reset during intialization. 4. Enable all 8 PCCs if Xframe II adapter. 5. Programs the RLDRAM size depending on the device. (Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb). 6. Enable extended(64-bit) statistics counters. 7. Program timer interrupt duration based on PCI/PCI-X clock speed. 8. Not required to save/restore PCI config space before/after reset. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io-regs.h b/drivers/net/s2io-regs.h index 826deb0..159d876 100644 --- a/drivers/net/s2io-regs.h +++ b/drivers/net/s2io-regs.h @@ -91,7 +91,21 @@ typedef struct _XENA_dev_config { SERR_SOURCE_MC | \ SERR_SOURCE_XGXS) - u8 unused_0[0x800 - 0x120]; + u64 pci_mode; +#define GET_PCI_MODE(val) ((val & vBIT(0xF, 0, 4)) >> 60) +#define PCI_MODE_PCI_33 0 +#define PCI_MODE_PCI_66 0x1 +#define PCI_MODE_PCIX_M1_66 0x2 +#define PCI_MODE_PCIX_M1_100 0x3 +#define PCI_MODE_PCIX_M1_133 0x4 +#define PCI_MODE_PCIX_M2_66 0x5 +#define PCI_MODE_PCIX_M2_100 0x6 +#define PCI_MODE_PCIX_M2_133 0x7 +#define PCI_MODE_UNSUPPORTED BIT(0) +#define PCI_MODE_32_BITS BIT(8) +#define PCI_MODE_UNKNOWN_MODE BIT(9) + + u8 unused_0[0x800 - 0x128]; /* PCI-X Controller registers */ u64 pic_int_status; @@ -223,19 +237,16 @@ typedef struct _XENA_dev_config { u64 xmsi_data; u64 rx_mat; +#define RX_MAT_SET(ring, msi) vBIT(msi, (8 * ring), 8) u8 unused6[0x8]; - u64 tx_mat0_7; - u64 tx_mat8_15; - u64 tx_mat16_23; - u64 tx_mat24_31; - u64 tx_mat32_39; - u64 tx_mat40_47; - u64 tx_mat48_55; - u64 tx_mat56_63; + u64 tx_mat0_n[0x8]; +#define TX_MAT_SET(fifo, msi) vBIT(msi, (8 * fifo), 8) - u8 unused_1[0x10]; + u8 unused_1[0x8]; + u64 stat_byte_cnt; +#define STAT_BC(n) vBIT(n,4,12) /* Automated statistics collection */ u64 stat_cfg; @@ -269,7 +280,12 @@ typedef struct _XENA_dev_config { u64 gpio_control; #define GPIO_CTRL_GPIO_0 BIT(8) - u8 unused7[0x600]; + u8 unused7_1[0x240 - 0x200]; + + u64 wreq_split_mask; +#define WREQ_SPLIT_MASK_SET_MASK(val) vBIT(val, 52, 12) + + u8 unused7_2[0x800 - 0x248]; /* TxDMA registers */ u64 txdma_int_status; @@ -470,6 +486,7 @@ typedef struct _XENA_dev_config { #define PRC_CTRL_NO_SNOOP (BIT(22)|BIT(23)) #define PRC_CTRL_NO_SNOOP_DESC BIT(22) #define PRC_CTRL_NO_SNOOP_BUFF BIT(23) +#define PRC_CTRL_BIMODAL_INTERRUPT BIT(37) #define PRC_CTRL_RXD_BACKOFF_INTERVAL(val) vBIT(val,40,24) u64 prc_alarm_action; @@ -742,7 +759,19 @@ typedef struct _XENA_dev_config { u64 mc_rldram_test_d1; u8 unused24[0x300 - 0x288]; u64 mc_rldram_test_d2; - u8 unused25[0x700 - 0x308]; + + u8 unused24_1[0x360 - 0x308]; + u64 mc_rldram_ctrl; +#define MC_RLDRAM_ENABLE_ODT BIT(7) + + u8 unused24_2[0x640 - 0x368]; + u64 mc_rldram_ref_per_herc; +#define MC_RLDRAM_SET_REF_PERIOD(val) vBIT(val, 0, 16) + + u8 unused24_3[0x660 - 0x648]; + u64 mc_rldram_mrs_herc; + + u8 unused25[0x700 - 0x668]; u64 mc_debug_ctrl; u8 unused26[0x3000 - 0x2f08]; diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index db3e394..15e2ee9 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -84,9 +84,10 @@ static inline int RXD_IS_UP2DT(RxD_t *rxdp) * problem, 600B, 600C, 600D, 640B, 640C and 640D. * macro below identifies these cards given the subsystem_id. */ -#define CARDS_WITH_FAULTY_LINK_INDICATORS(subid) \ - (((subid >= 0x600B) && (subid <= 0x600D)) || \ - ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0 +#define CARDS_WITH_FAULTY_LINK_INDICATORS(dev_type, subid) \ + (dev_type == XFRAME_I_DEVICE) ? \ + ((((subid >= 0x600B) && (subid <= 0x600D)) || \ + ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0) : 0 #define LINK_IS_UP(val64) (!(val64 & (ADAPTER_STATUS_RMAC_REMOTE_FAULT | \ ADAPTER_STATUS_RMAC_LOCAL_FAULT))) @@ -207,7 +208,24 @@ static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid) #define SWITCH_SIGN 0xA5A5A5A5A5A5A5A5ULL #define END_SIGN 0x0 -static u64 default_mdio_cfg[] = { +static u64 herc_act_dtx_cfg[] = { + /* Set address */ + 0x80000515BA750000ULL, 0x80000515BA7500E0ULL, + /* Write data */ + 0x80000515BA750004ULL, 0x80000515BA7500E4ULL, + /* Set address */ + 0x80010515003F0000ULL, 0x80010515003F00E0ULL, + /* Write data */ + 0x80010515003F0004ULL, 0x80010515003F00E4ULL, + /* Set address */ + 0x80020515F2100000ULL, 0x80020515F21000E0ULL, + /* Write data */ + 0x80020515F2100004ULL, 0x80020515F21000E4ULL, + /* Done */ + END_SIGN +}; + +static u64 xena_mdio_cfg[] = { /* Reset PMA PLL */ 0xC001010000000000ULL, 0xC0010100000000E0ULL, 0xC0010100008000E4ULL, @@ -217,7 +235,7 @@ static u64 default_mdio_cfg[] = { END_SIGN }; -static u64 default_dtx_cfg[] = { +static u64 xena_dtx_cfg[] = { 0x8000051500000000ULL, 0x80000515000000E0ULL, 0x80000515D93500E4ULL, 0x8001051500000000ULL, 0x80010515000000E0ULL, 0x80010515001E00E4ULL, @@ -656,6 +674,87 @@ static void free_shared_mem(struct s2io_nic *nic) } /** + * s2io_verify_pci_mode - + */ + +static int s2io_verify_pci_mode(nic_t *nic) +{ + XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0; + register u64 val64 = 0; + int mode; + + val64 = readq(&bar0->pci_mode); + mode = (u8)GET_PCI_MODE(val64); + + if ( val64 & PCI_MODE_UNKNOWN_MODE) + return -1; /* Unknown PCI mode */ + return mode; +} + + +/** + * s2io_print_pci_mode - + */ +static int s2io_print_pci_mode(nic_t *nic) +{ + XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0; + register u64 val64 = 0; + int mode; + struct config_param *config = &nic->config; + + val64 = readq(&bar0->pci_mode); + mode = (u8)GET_PCI_MODE(val64); + + if ( val64 & PCI_MODE_UNKNOWN_MODE) + return -1; /* Unknown PCI mode */ + + if (val64 & PCI_MODE_32_BITS) { + DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name); + } else { + DBG_PRINT(ERR_DBG, "%s: Device is on 64 bit ", nic->dev->name); + } + + switch(mode) { + case PCI_MODE_PCI_33: + DBG_PRINT(ERR_DBG, "33MHz PCI bus\n"); + config->bus_speed = 33; + break; + case PCI_MODE_PCI_66: + DBG_PRINT(ERR_DBG, "66MHz PCI bus\n"); + config->bus_speed = 133; + break; + case PCI_MODE_PCIX_M1_66: + DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n"); + config->bus_speed = 133; /* Herc doubles the clock rate */ + break; + case PCI_MODE_PCIX_M1_100: + DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n"); + config->bus_speed = 200; + break; + case PCI_MODE_PCIX_M1_133: + DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n"); + config->bus_speed = 266; + break; + case PCI_MODE_PCIX_M2_66: + DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n"); + config->bus_speed = 133; + break; + case PCI_MODE_PCIX_M2_100: + DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n"); + config->bus_speed = 200; + break; + case PCI_MODE_PCIX_M2_133: + DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n"); + config->bus_speed = 266; + break; + default: + return -1; /* Unsupported bus speed */ + } + + return mode; +} + +/** * init_nic - Initialization of hardware * @nic: device peivate variable * Description: The function sequentially configures every block @@ -687,6 +786,16 @@ static int init_nic(struct s2io_nic *nic) return -1; } + /* + * Herc requires EOI to be removed from reset before XGXS, so.. + */ + if (nic->device_type & XFRAME_II_DEVICE) { + val64 = 0xA500000000ULL; + writeq(val64, &bar0->sw_reset); + msleep(500); + val64 = readq(&bar0->sw_reset); + } + /* Remove XGXS from reset state */ val64 = 0; writeq(val64, &bar0->sw_reset); @@ -718,41 +827,51 @@ static int init_nic(struct s2io_nic *nic) * of 64 bit values into two registers in a particular * sequence. Hence a macro 'SWITCH_SIGN' has been defined * which will be defined in the array of configuration values - * (default_dtx_cfg & default_mdio_cfg) at appropriate places + * (xena_dtx_cfg & xena_mdio_cfg) at appropriate places * to switch writing from one regsiter to another. We continue * writing these values until we encounter the 'END_SIGN' macro. * For example, After making a series of 21 writes into * dtx_control register the 'SWITCH_SIGN' appears and hence we * start writing into mdio_control until we encounter END_SIGN. */ - while (1) { - dtx_cfg: - while (default_dtx_cfg[dtx_cnt] != END_SIGN) { - if (default_dtx_cfg[dtx_cnt] == SWITCH_SIGN) { - dtx_cnt++; - goto mdio_cfg; - } - SPECIAL_REG_WRITE(default_dtx_cfg[dtx_cnt], + if (nic->device_type & XFRAME_II_DEVICE) { + while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) { + SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt], &bar0->dtx_control, UF); - val64 = readq(&bar0->dtx_control); + if (dtx_cnt & 0x1) + msleep(1); /* Necessary!! */ dtx_cnt++; } - mdio_cfg: - while (default_mdio_cfg[mdio_cnt] != END_SIGN) { - if (default_mdio_cfg[mdio_cnt] == SWITCH_SIGN) { + } else { + while (1) { + dtx_cfg: + while (xena_dtx_cfg[dtx_cnt] != END_SIGN) { + if (xena_dtx_cfg[dtx_cnt] == SWITCH_SIGN) { + dtx_cnt++; + goto mdio_cfg; + } + SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt], + &bar0->dtx_control, UF); + val64 = readq(&bar0->dtx_control); + dtx_cnt++; + } + mdio_cfg: + while (xena_mdio_cfg[mdio_cnt] != END_SIGN) { + if (xena_mdio_cfg[mdio_cnt] == SWITCH_SIGN) { + mdio_cnt++; + goto dtx_cfg; + } + SPECIAL_REG_WRITE(xena_mdio_cfg[mdio_cnt], + &bar0->mdio_control, UF); + val64 = readq(&bar0->mdio_control); mdio_cnt++; + } + if ((xena_dtx_cfg[dtx_cnt] == END_SIGN) && + (xena_mdio_cfg[mdio_cnt] == END_SIGN)) { + break; + } else { goto dtx_cfg; } - SPECIAL_REG_WRITE(default_mdio_cfg[mdio_cnt], - &bar0->mdio_control, UF); - val64 = readq(&bar0->mdio_control); - mdio_cnt++; - } - if ((default_dtx_cfg[dtx_cnt] == END_SIGN) && - (default_mdio_cfg[mdio_cnt] == END_SIGN)) { - break; - } else { - goto dtx_cfg; } } @@ -803,7 +922,8 @@ static int init_nic(struct s2io_nic *nic) * Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug * SXE-008 TRANSMIT DMA ARBITRATION ISSUE. */ - if (get_xena_rev_id(nic->pdev) < 4) + if ((nic->device_type == XFRAME_I_DEVICE) && + (get_xena_rev_id(nic->pdev) < 4)) writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable); val64 = readq(&bar0->tx_fifo_partition_0); @@ -833,7 +953,11 @@ static int init_nic(struct s2io_nic *nic) * configured Rings. */ val64 = 0; - mem_size = 64; + if (nic->device_type & XFRAME_II_DEVICE) + mem_size = 32; + else + mem_size = 64; + for (i = 0; i < config->rx_ring_num; i++) { switch (i) { case 0: @@ -1116,6 +1240,11 @@ static int init_nic(struct s2io_nic *nic) /* Program statistics memory */ writeq(mac_control->stats_mem_phy, &bar0->stat_addr); + if (nic->device_type == XFRAME_II_DEVICE) { + val64 = STAT_BC(0x320); + writeq(val64, &bar0->stat_byte_cnt); + } + /* * Initializing the sampling rate for the device to calculate the * bandwidth utilization. @@ -1134,12 +1263,18 @@ static int init_nic(struct s2io_nic *nic) * 250 interrupts per sec. Continuous interrupts are enabled * by default. */ - val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078) | - TTI_DATA1_MEM_TX_URNG_A(0xA) | + if (nic->device_type == XFRAME_II_DEVICE) { + int count = (nic->config.bus_speed * 125)/2; + val64 = TTI_DATA1_MEM_TX_TIMER_VAL(count); + } else { + + val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078); + } + val64 |= TTI_DATA1_MEM_TX_URNG_A(0xA) | TTI_DATA1_MEM_TX_URNG_B(0x10) | TTI_DATA1_MEM_TX_URNG_C(0x30) | TTI_DATA1_MEM_TX_TIMER_AC_EN; - if (use_continuous_tx_intrs) - val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN; + if (use_continuous_tx_intrs) + val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN; writeq(val64, &bar0->tti_data1_mem); val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) | @@ -1171,9 +1306,19 @@ static int init_nic(struct s2io_nic *nic) time++; } + /* RTI Initialization */ - val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF) | - RTI_DATA1_MEM_RX_URNG_A(0xA) | + if (nic->device_type == XFRAME_II_DEVICE) { + /* + * Programmed to generate Apprx 500 Intrs per + * second + */ + int count = (nic->config.bus_speed * 125)/4; + val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count); + } else { + val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF); + } + val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) | RTI_DATA1_MEM_RX_URNG_B(0x10) | RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN; @@ -1267,6 +1412,15 @@ static int init_nic(struct s2io_nic *nic) val64 |= PIC_CNTL_SHARED_SPLITS(shared_splits); writeq(val64, &bar0->pic_control); + /* + * Programming the Herc to split every write transaction + * that does not start on an ADB to reduce disconnects. + */ + if (nic->device_type == XFRAME_II_DEVICE) { + val64 = WREQ_SPLIT_MASK_SET_MASK(255); + writeq(val64, &bar0->wreq_split_mask); + } + return SUCCESS; } @@ -1509,18 +1663,18 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) } } -static int check_prc_pcc_state(u64 val64, int flag, int rev_id) +static int check_prc_pcc_state(u64 val64, int flag, int rev_id, int herc) { int ret = 0; if (flag == FALSE) { - if (rev_id >= 4) { + if ((!herc && (rev_id >= 4)) || herc) { if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) && ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == ADAPTER_STATUS_RC_PRC_QUIESCENT)) { ret = 1; } - } else { + }else { if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) && ((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) == ADAPTER_STATUS_RC_PRC_QUIESCENT)) { @@ -1528,7 +1682,7 @@ static int check_prc_pcc_state(u64 val64, int flag, int rev_id) } } } else { - if (rev_id >= 4) { + if ((!herc && (rev_id >= 4)) || herc) { if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) == ADAPTER_STATUS_RMAC_PCC_IDLE) && (!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) || @@ -1564,10 +1718,11 @@ static int check_prc_pcc_state(u64 val64, int flag, int rev_id) static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag) { - int ret = 0; + int ret = 0, herc; u64 tmp64 = ~((u64) val64); int rev_id = get_xena_rev_id(sp->pdev); + herc = (sp->device_type == XFRAME_II_DEVICE); if (! (tmp64 & (ADAPTER_STATUS_TDMA_READY | ADAPTER_STATUS_RDMA_READY | @@ -1575,7 +1730,7 @@ static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag) ADAPTER_STATUS_PIC_QUIESCENT | ADAPTER_STATUS_MC_DRAM_READY | ADAPTER_STATUS_MC_QUEUES_READY | ADAPTER_STATUS_M_PLL_LOCK | ADAPTER_STATUS_P_PLL_LOCK))) { - ret = check_prc_pcc_state(val64, flag, rev_id); + ret = check_prc_pcc_state(val64, flag, rev_id, herc); } return ret; @@ -1706,7 +1861,8 @@ static int start_nic(struct s2io_nic *nic) /* SXE-002: Initialize link and activity LED */ subid = nic->pdev->subsystem_device; - if ((subid & 0xFF) >= 0x07) { + if (((subid & 0xFF) >= 0x07) && + (nic->device_type == XFRAME_I_DEVICE)) { val64 = readq(&bar0->gpio_control); val64 |= 0x0000800000000000ULL; writeq(val64, &bar0->gpio_control); @@ -2541,9 +2697,12 @@ void s2io_reset(nic_t * sp) */ msleep(250); + if (!(sp->device_type & XFRAME_II_DEVICE)) { /* Restore the PCI state saved during initializarion. */ - pci_restore_state(sp->pdev); - + pci_restore_state(sp->pdev); + } else { + pci_set_master(sp->pdev); + } s2io_init_pci(sp); msleep(250); @@ -2568,7 +2727,8 @@ void s2io_reset(nic_t * sp) /* SXE-002: Configure link and activity LED to turn it off */ subid = sp->pdev->subsystem_device; - if ((subid & 0xFF) >= 0x07) { + if (((subid & 0xFF) >= 0x07) && + (sp->device_type == XFRAME_I_DEVICE)) { val64 = readq(&bar0->gpio_control); val64 |= 0x0000800000000000ULL; writeq(val64, &bar0->gpio_control); @@ -2576,6 +2736,15 @@ void s2io_reset(nic_t * sp) writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700)); } + /* + * Clear spurious ECC interrupts that would have occured on + * XFRAME II cards after reset. + */ + if (sp->device_type == XFRAME_II_DEVICE) { + val64 = readq(&bar0->pcc_err_reg); + writeq(val64, &bar0->pcc_err_reg); + } + sp->device_enabled_once = FALSE; } @@ -3463,7 +3632,8 @@ static void s2io_phy_id(unsigned long data) u16 subid; subid = sp->pdev->subsystem_device; - if ((subid & 0xFF) >= 0x07) { + if ((sp->device_type == XFRAME_II_DEVICE) || + ((subid & 0xFF) >= 0x07)) { val64 = readq(&bar0->gpio_control); val64 ^= GPIO_CTRL_GPIO_0; writeq(val64, &bar0->gpio_control); @@ -3500,7 +3670,8 @@ static int s2io_ethtool_idnic(struct net_device *dev, u32 data) subid = sp->pdev->subsystem_device; last_gpio_ctrl_val = readq(&bar0->gpio_control); - if ((subid & 0xFF) < 0x07) { + if ((sp->device_type == XFRAME_I_DEVICE) && + ((subid & 0xFF) < 0x07)) { val64 = readq(&bar0->adapter_control); if (!(val64 & ADAPTER_CNTL_EN)) { printk(KERN_ERR @@ -3520,7 +3691,7 @@ static int s2io_ethtool_idnic(struct net_device *dev, u32 data) msleep_interruptible(MAX_FLICKER_TIME); del_timer_sync(&sp->id_timer); - if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) { + if (CARDS_WITH_FAULTY_LINK_INDICATORS(sp->device_type, subid)) { writeq(last_gpio_ctrl_val, &bar0->gpio_control); last_gpio_ctrl_val = readq(&bar0->gpio_control); } @@ -4134,44 +4305,91 @@ static void s2io_get_ethtool_stats(struct net_device *dev, StatInfo_t *stat_info = sp->mac_control.stats_info; s2io_updt_stats(sp); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_data_octets); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_frms_oflow) << 32 | + le32_to_cpu(stat_info->tmac_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_data_octets_oflow) << 32 | + le32_to_cpu(stat_info->tmac_data_octets); tmp_stats[i++] = le64_to_cpu(stat_info->tmac_drop_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_mcst_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_bcst_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_mcst_frms_oflow) << 32 | + le32_to_cpu(stat_info->tmac_mcst_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_bcst_frms_oflow) << 32 | + le32_to_cpu(stat_info->tmac_bcst_frms); tmp_stats[i++] = le64_to_cpu(stat_info->tmac_pause_ctrl_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_any_err_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_any_err_frms_oflow) << 32 | + le32_to_cpu(stat_info->tmac_any_err_frms); tmp_stats[i++] = le64_to_cpu(stat_info->tmac_vld_ip_octets); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_vld_ip); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_drop_ip); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_icmp); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_rst_tcp); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_vld_ip_oflow) << 32 | + le32_to_cpu(stat_info->tmac_vld_ip); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_drop_ip_oflow) << 32 | + le32_to_cpu(stat_info->tmac_drop_ip); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_icmp_oflow) << 32 | + le32_to_cpu(stat_info->tmac_icmp); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->tmac_rst_tcp_oflow) << 32 | + le32_to_cpu(stat_info->tmac_rst_tcp); tmp_stats[i++] = le64_to_cpu(stat_info->tmac_tcp); - tmp_stats[i++] = le32_to_cpu(stat_info->tmac_udp); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_data_octets); + tmp_stats[i++] = (u64)le32_to_cpu(stat_info->tmac_udp_oflow) << 32 | + le32_to_cpu(stat_info->tmac_udp); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_vld_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_vld_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_data_octets_oflow) << 32 | + le32_to_cpu(stat_info->rmac_data_octets); tmp_stats[i++] = le64_to_cpu(stat_info->rmac_fcs_err_frms); tmp_stats[i++] = le64_to_cpu(stat_info->rmac_drop_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_mcst_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_bcst_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_vld_mcst_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_vld_mcst_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_vld_bcst_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_vld_bcst_frms); tmp_stats[i++] = le32_to_cpu(stat_info->rmac_in_rng_len_err_frms); tmp_stats[i++] = le64_to_cpu(stat_info->rmac_long_frms); tmp_stats[i++] = le64_to_cpu(stat_info->rmac_pause_ctrl_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_discarded_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_usized_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_osized_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_frag_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_jabber_frms); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_ip); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_discarded_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_discarded_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_usized_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_usized_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_osized_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_osized_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_frag_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_frag_frms); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_jabber_frms_oflow) << 32 | + le32_to_cpu(stat_info->rmac_jabber_frms); + tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_ip_oflow) << 32 | + le32_to_cpu(stat_info->rmac_ip); tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ip_octets); tmp_stats[i++] = le32_to_cpu(stat_info->rmac_hdr_err_ip); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_drop_ip); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_icmp); + tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_drop_ip_oflow) << 32 | + le32_to_cpu(stat_info->rmac_drop_ip); + tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_icmp_oflow) << 32 | + le32_to_cpu(stat_info->rmac_icmp); tmp_stats[i++] = le64_to_cpu(stat_info->rmac_tcp); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_udp); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_drp_udp); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_pause_cnt); - tmp_stats[i++] = le32_to_cpu(stat_info->rmac_accepted_ip); + tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_udp_oflow) << 32 | + le32_to_cpu(stat_info->rmac_udp); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_err_drp_udp_oflow) << 32 | + le32_to_cpu(stat_info->rmac_err_drp_udp); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_pause_cnt_oflow) << 32 | + le32_to_cpu(stat_info->rmac_pause_cnt); + tmp_stats[i++] = + (u64)le32_to_cpu(stat_info->rmac_accepted_ip_oflow) << 32 | + le32_to_cpu(stat_info->rmac_accepted_ip); tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp); tmp_stats[i++] = 0; tmp_stats[i++] = stat_info->sw_stat.single_ecc_errs; @@ -4401,7 +4619,8 @@ static void s2io_set_link(unsigned long data) val64 = readq(&bar0->adapter_control); val64 |= ADAPTER_CNTL_EN; writeq(val64, &bar0->adapter_control); - if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) { + if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type, + subid)) { val64 = readq(&bar0->gpio_control); val64 |= GPIO_CTRL_GPIO_0; writeq(val64, &bar0->gpio_control); @@ -4423,7 +4642,8 @@ static void s2io_set_link(unsigned long data) } s2io_link(nic, LINK_UP); } else { - if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) { + if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type, + subid)) { val64 = readq(&bar0->gpio_control); val64 &= ~GPIO_CTRL_GPIO_0; writeq(val64, &bar0->gpio_control); @@ -4708,7 +4928,6 @@ static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp) netif_rx(skb); } #endif - dev->last_rx = jiffies; atomic_dec(&sp->rx_bufs_left[ring_no]); return SUCCESS; @@ -4842,6 +5061,7 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) u16 subid; mac_info_t *mac_control; struct config_param *config; + int mode; #ifdef CONFIG_S2IO_NAPI DBG_PRINT(ERR_DBG, "NAPI support has been enabled\n"); @@ -4898,6 +5118,12 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) sp->high_dma_flag = dma_flag; sp->device_enabled_once = FALSE; + if ((pdev->device == PCI_DEVICE_ID_HERC_WIN) || + (pdev->device == PCI_DEVICE_ID_HERC_UNI)) + sp->device_type = XFRAME_II_DEVICE; + else + sp->device_type = XFRAME_I_DEVICE; + /* Initialize some PCI/PCI-X fields of the NIC. */ s2io_init_pci(sp); @@ -5033,7 +5259,9 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) INIT_WORK(&sp->set_link_task, (void (*)(void *)) s2io_set_link, sp); - pci_save_state(sp->pdev); + if (!(sp->device_type & XFRAME_II_DEVICE)) { + pci_save_state(sp->pdev); + } /* Setting swapper control on the NIC, for proper reset operation */ if (s2io_set_swapper(sp)) { @@ -5043,12 +5271,26 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) goto set_swap_failed; } - /* - * Fix for all "FFs" MAC address problems observed on - * Alpha platforms - */ - fix_mac_address(sp); - s2io_reset(sp); + /* Verify if the Herc works on the slot its placed into */ + if (sp->device_type & XFRAME_II_DEVICE) { + mode = s2io_verify_pci_mode(sp); + if (mode < 0) { + DBG_PRINT(ERR_DBG, "%s: ", __FUNCTION__); + DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n"); + ret = -EBADSLT; + goto set_swap_failed; + } + } + + /* Not needed for Herc */ + if (sp->device_type & XFRAME_I_DEVICE) { + /* + * Fix for all "FFs" MAC address problems observed on + * Alpha platforms + */ + fix_mac_address(sp); + s2io_reset(sp); + } /* * MAC address initialization. @@ -5073,22 +5315,13 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) sp->def_mac_addr[0].mac_addr[5] = (u8) (mac_down >> 16); sp->def_mac_addr[0].mac_addr[4] = (u8) (mac_down >> 24); - DBG_PRINT(INIT_DBG, - "DEFAULT MAC ADDR:0x%02x-%02x-%02x-%02x-%02x-%02x\n", - sp->def_mac_addr[0].mac_addr[0], - sp->def_mac_addr[0].mac_addr[1], - sp->def_mac_addr[0].mac_addr[2], - sp->def_mac_addr[0].mac_addr[3], - sp->def_mac_addr[0].mac_addr[4], - sp->def_mac_addr[0].mac_addr[5]); - /* Set the factory defined MAC address initially */ dev->addr_len = ETH_ALEN; memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN); /* * Initialize the tasklet status and link state flags - * and the card statte parameter + * and the card state parameter */ atomic_set(&(sp->card_state), 0); sp->tasklet_status = 0; @@ -5123,9 +5356,46 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) goto register_failed; } + if (sp->device_type & XFRAME_II_DEVICE) { + DBG_PRINT(ERR_DBG, "%s: Neterion Xframe II 10GbE adapter ", + dev->name); + DBG_PRINT(ERR_DBG, "(rev %d), Driver %s\n", + get_xena_rev_id(sp->pdev), + s2io_driver_version); + DBG_PRINT(ERR_DBG, "MAC ADDR: %02x:%02x:%02x:%02x:%02x:%02x\n", + sp->def_mac_addr[0].mac_addr[0], + sp->def_mac_addr[0].mac_addr[1], + sp->def_mac_addr[0].mac_addr[2], + sp->def_mac_addr[0].mac_addr[3], + sp->def_mac_addr[0].mac_addr[4], + sp->def_mac_addr[0].mac_addr[5]); + int mode = s2io_print_pci_mode(sp); + if (mode < 0) { + DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode "); + ret = -EBADSLT; + goto set_swap_failed; + } + } else { + DBG_PRINT(ERR_DBG, "%s: Neterion Xframe I 10GbE adapter ", + dev->name); + DBG_PRINT(ERR_DBG, "(rev %d), Driver %s\n", + get_xena_rev_id(sp->pdev), + s2io_driver_version); + DBG_PRINT(ERR_DBG, "MAC ADDR: %02x:%02x:%02x:%02x:%02x:%02x\n", + sp->def_mac_addr[0].mac_addr[0], + sp->def_mac_addr[0].mac_addr[1], + sp->def_mac_addr[0].mac_addr[2], + sp->def_mac_addr[0].mac_addr[3], + sp->def_mac_addr[0].mac_addr[4], + sp->def_mac_addr[0].mac_addr[5]); + } + /* Initialize device name */ strcpy(sp->name, dev->name); - strcat(sp->name, ": Neterion Xframe I 10GbE adapter"); + if (sp->device_type & XFRAME_II_DEVICE) + strcat(sp->name, ": Neterion Xframe II 10GbE adapter"); + else + strcat(sp->name, ": Neterion Xframe I 10GbE adapter"); /* * Make Link state as off at this point, when the Link change diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index b924ef2..df8cfd0 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -201,6 +201,67 @@ typedef struct stat_block { u32 rxf_wr_cnt; u32 txf_rd_cnt; +/* Tx MAC statistics overflow counters. */ + u32 tmac_data_octets_oflow; + u32 tmac_frms_oflow; + u32 tmac_bcst_frms_oflow; + u32 tmac_mcst_frms_oflow; + u32 tmac_ucst_frms_oflow; + u32 tmac_ttl_octets_oflow; + u32 tmac_any_err_frms_oflow; + u32 tmac_nucst_frms_oflow; + u64 tmac_vlan_frms; + u32 tmac_drop_ip_oflow; + u32 tmac_vld_ip_oflow; + u32 tmac_rst_tcp_oflow; + u32 tmac_icmp_oflow; + u32 tpa_unknown_protocol; + u32 tmac_udp_oflow; + u32 reserved_10; + u32 tpa_parse_failure; + +/* Rx MAC Statistics overflow counters. */ + u32 rmac_data_octets_oflow; + u32 rmac_vld_frms_oflow; + u32 rmac_vld_bcst_frms_oflow; + u32 rmac_vld_mcst_frms_oflow; + u32 rmac_accepted_ucst_frms_oflow; + u32 rmac_ttl_octets_oflow; + u32 rmac_discarded_frms_oflow; + u32 rmac_accepted_nucst_frms_oflow; + u32 rmac_usized_frms_oflow; + u32 rmac_drop_events_oflow; + u32 rmac_frag_frms_oflow; + u32 rmac_osized_frms_oflow; + u32 rmac_ip_oflow; + u32 rmac_jabber_frms_oflow; + u32 rmac_icmp_oflow; + u32 rmac_drop_ip_oflow; + u32 rmac_err_drp_udp_oflow; + u32 rmac_udp_oflow; + u32 reserved_11; + u32 rmac_pause_cnt_oflow; + u64 rmac_ttl_1519_4095_frms; + u64 rmac_ttl_4096_8191_frms; + u64 rmac_ttl_8192_max_frms; + u64 rmac_ttl_gt_max_frms; + u64 rmac_osized_alt_frms; + u64 rmac_jabber_alt_frms; + u64 rmac_gt_max_alt_frms; + u64 rmac_vlan_frms; + u32 rmac_len_discard; + u32 rmac_fcs_discard; + u32 rmac_pf_discard; + u32 rmac_da_discard; + u32 rmac_red_discard; + u32 rmac_rts_discard; + u32 reserved_12; + u32 rmac_ingm_full_discard; + u32 reserved_13; + u32 rmac_accepted_ip_oflow; + u32 reserved_14; + u32 link_fault_cnt; + /* Software statistics maintained by driver */ swStat_t sw_stat; } StatInfo_t; @@ -690,6 +751,9 @@ struct s2io_nic { atomic_t card_state; volatile unsigned long link_state; struct vlan_group *vlgrp; +#define XFRAME_I_DEVICE 1 +#define XFRAME_II_DEVICE 2 + u8 device_type; spinlock_t rx_lock; atomic_t isr_cnt; -- cgit v0.10.2 From b6e3f9828b9dc188cfe80364365cc68bf45df949 Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:38:01 -0700 Subject: [PATCH] S2io: Support for bimodal interrupts Hi, This is a patch to provide bimodal interrupt moderation support for Xframe II adapter. Basically, in this moderation scheme, the adapter raises a traffic interrupt if the no. of packets transmitted and/or received reaches a programmable threshold. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 15e2ee9..f430ffe 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -297,6 +297,7 @@ static unsigned int mc_pause_threshold_q4q7 = 187; static unsigned int shared_splits; static unsigned int tmac_util_period = 5; static unsigned int rmac_util_period = 5; +static unsigned int bimodal = 0; #ifndef CONFIG_S2IO_NAPI static unsigned int indicate_max_pkts; #endif @@ -1306,52 +1307,86 @@ static int init_nic(struct s2io_nic *nic) time++; } + if (nic->config.bimodal) { + int k = 0; + for (k = 0; k < config->rx_ring_num; k++) { + val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD; + val64 |= TTI_CMD_MEM_OFFSET(0x38+k); + writeq(val64, &bar0->tti_command_mem); - /* RTI Initialization */ - if (nic->device_type == XFRAME_II_DEVICE) { /* - * Programmed to generate Apprx 500 Intrs per - * second - */ - int count = (nic->config.bus_speed * 125)/4; - val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count); + * Once the operation completes, the Strobe bit of the command + * register will be reset. We poll for this particular condition + * We wait for a maximum of 500ms for the operation to complete, + * if it's not complete by then we return error. + */ + time = 0; + while (TRUE) { + val64 = readq(&bar0->tti_command_mem); + if (!(val64 & TTI_CMD_MEM_STROBE_NEW_CMD)) { + break; + } + if (time > 10) { + DBG_PRINT(ERR_DBG, + "%s: TTI init Failed\n", + dev->name); + return -1; + } + time++; + msleep(50); + } + } } else { - val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF); - } - val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) | - RTI_DATA1_MEM_RX_URNG_B(0x10) | - RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN; - writeq(val64, &bar0->rti_data1_mem); + /* RTI Initialization */ + if (nic->device_type == XFRAME_II_DEVICE) { + /* + * Programmed to generate Apprx 500 Intrs per + * second + */ + int count = (nic->config.bus_speed * 125)/4; + val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count); + } else { + val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF); + } + val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) | + RTI_DATA1_MEM_RX_URNG_B(0x10) | + RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN; - val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) | - RTI_DATA2_MEM_RX_UFC_B(0x2) | - RTI_DATA2_MEM_RX_UFC_C(0x40) | RTI_DATA2_MEM_RX_UFC_D(0x80); - writeq(val64, &bar0->rti_data2_mem); + writeq(val64, &bar0->rti_data1_mem); - val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD; - writeq(val64, &bar0->rti_command_mem); + val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) | + RTI_DATA2_MEM_RX_UFC_B(0x2) | + RTI_DATA2_MEM_RX_UFC_C(0x40) | RTI_DATA2_MEM_RX_UFC_D(0x80); + writeq(val64, &bar0->rti_data2_mem); - /* - * Once the operation completes, the Strobe bit of the - * command register will be reset. We poll for this - * particular condition. We wait for a maximum of 500ms - * for the operation to complete, if it's not complete - * by then we return error. - */ - time = 0; - while (TRUE) { - val64 = readq(&bar0->rti_command_mem); - if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD)) { - break; - } - if (time > 10) { - DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n", - dev->name); - return -1; + for (i = 0; i < config->rx_ring_num; i++) { + val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD + | RTI_CMD_MEM_OFFSET(i); + writeq(val64, &bar0->rti_command_mem); + + /* + * Once the operation completes, the Strobe bit of the + * command register will be reset. We poll for this + * particular condition. We wait for a maximum of 500ms + * for the operation to complete, if it's not complete + * by then we return error. + */ + time = 0; + while (TRUE) { + val64 = readq(&bar0->rti_command_mem); + if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD)) { + break; + } + if (time > 10) { + DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n", + dev->name); + return -1; + } + time++; + msleep(50); + } } - time++; - msleep(50); } /* @@ -1789,6 +1824,8 @@ static int start_nic(struct s2io_nic *nic) &bar0->prc_rxd0_n[i]); val64 = readq(&bar0->prc_ctrl_n[i]); + if (nic->config.bimodal) + val64 |= PRC_CTRL_BIMODAL_INTERRUPT; #ifndef CONFIG_2BUFF_MODE val64 |= PRC_CTRL_RC_ENABLED; #else @@ -5030,6 +5067,7 @@ module_param(mc_pause_threshold_q4q7, int, 0); module_param(shared_splits, int, 0); module_param(tmac_util_period, int, 0); module_param(rmac_util_period, int, 0); +module_param(bimodal, bool, 0); #ifndef CONFIG_S2IO_NAPI module_param(indicate_max_pkts, int, 0); #endif @@ -5397,6 +5435,14 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) else strcat(sp->name, ": Neterion Xframe I 10GbE adapter"); + /* Initialize bimodal Interrupts */ + sp->config.bimodal = bimodal; + if (!(sp->device_type & XFRAME_II_DEVICE) && bimodal) { + sp->config.bimodal = 0; + DBG_PRINT(ERR_DBG,"%s:Bimodal intr not supported by Xframe I\n", + dev->name); + } + /* * Make Link state as off at this point, when the Link change * interrupt comes the state will be automatically changed to diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index df8cfd0..9463145 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -261,8 +261,6 @@ typedef struct stat_block { u32 rmac_accepted_ip_oflow; u32 reserved_14; u32 link_fault_cnt; - -/* Software statistics maintained by driver */ swStat_t sw_stat; } StatInfo_t; @@ -349,6 +347,7 @@ struct config_param { #define MAX_RX_BLOCKS_PER_RING 150 rx_ring_config_t rx_cfg[MAX_RX_RINGS]; /*Per-Rx Ring config */ + u8 bimodal; /*Flag for setting bimodal interrupts*/ #define HEADER_ETHERNET_II_802_3_SIZE 14 #define HEADER_802_2_SIZE 3 -- cgit v0.10.2 From a371a07de9bce837ea4e84569a2b390a42e360ef Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:38:59 -0700 Subject: [PATCH] S2io: New link handling scheme for Xframe II Hi, The below patch implements a new "Link state change handling" scheme supported by the Xframe II adapter. It also bumps up the driver version to 2.0.2.0. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io-regs.h b/drivers/net/s2io-regs.h index 159d876..2234a8f 100644 --- a/drivers/net/s2io-regs.h +++ b/drivers/net/s2io-regs.h @@ -167,7 +167,11 @@ typedef struct _XENA_dev_config { u8 unused4[0x08]; u64 gpio_int_reg; +#define GPIO_INT_REG_LINK_DOWN BIT(1) +#define GPIO_INT_REG_LINK_UP BIT(2) u64 gpio_int_mask; +#define GPIO_INT_MASK_LINK_DOWN BIT(1) +#define GPIO_INT_MASK_LINK_UP BIT(2) u64 gpio_alarms; u8 unused5[0x38]; @@ -279,8 +283,10 @@ typedef struct _XENA_dev_config { u64 gpio_control; #define GPIO_CTRL_GPIO_0 BIT(8) + u64 misc_control; +#define MISC_LINK_STABILITY_PRD(val) vBIT(val,29,3) - u8 unused7_1[0x240 - 0x200]; + u8 unused7_1[0x240 - 0x208]; u64 wreq_split_mask; #define WREQ_SPLIT_MASK_SET_MASK(val) vBIT(val, 52, 12) diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index f430ffe..e7c4285 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -67,7 +67,7 @@ /* S2io Driver name & version. */ static char s2io_driver_name[] = "Neterion"; -static char s2io_driver_version[] = "Version 1.7.7"; +static char s2io_driver_version[] = "Version 2.0.2.0"; static inline int RXD_IS_UP2DT(RxD_t *rxdp) { @@ -1456,8 +1456,28 @@ static int init_nic(struct s2io_nic *nic) writeq(val64, &bar0->wreq_split_mask); } + /* Setting Link stability period to 64 ms */ + if (nic->device_type == XFRAME_II_DEVICE) { + val64 = MISC_LINK_STABILITY_PRD(3); + writeq(val64, &bar0->misc_control); + } + return SUCCESS; } +#define LINK_UP_DOWN_INTERRUPT 1 +#define MAC_RMAC_ERR_TIMER 2 + +#if defined(CONFIG_MSI_MODE) || defined(CONFIG_MSIX_MODE) +#define s2io_link_fault_indication(x) MAC_RMAC_ERR_TIMER +#else +int s2io_link_fault_indication(nic_t *nic) +{ + if (nic->device_type == XFRAME_II_DEVICE) + return LINK_UP_DOWN_INTERRUPT; + else + return MAC_RMAC_ERR_TIMER; +} +#endif /** * en_dis_able_nic_intrs - Enable or Disable the interrupts @@ -1485,11 +1505,22 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) temp64 &= ~((u64) val64); writeq(temp64, &bar0->general_int_mask); /* - * Disabled all PCIX, Flash, MDIO, IIC and GPIO + * If Hercules adapter enable GPIO otherwise + * disabled all PCIX, Flash, MDIO, IIC and GPIO * interrupts for now. * TODO */ - writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask); + if (s2io_link_fault_indication(nic) == + LINK_UP_DOWN_INTERRUPT ) { + temp64 = readq(&bar0->pic_int_mask); + temp64 &= ~((u64) PIC_INT_GPIO); + writeq(temp64, &bar0->pic_int_mask); + temp64 = readq(&bar0->gpio_int_mask); + temp64 &= ~((u64) GPIO_INT_MASK_LINK_UP); + writeq(temp64, &bar0->gpio_int_mask); + } else { + writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask); + } /* * No MSI Support is available presently, so TTI and * RTI interrupts are also disabled. @@ -1580,17 +1611,8 @@ static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag) writeq(temp64, &bar0->general_int_mask); /* * All MAC block error interrupts are disabled for now - * except the link status change interrupt. * TODO */ - val64 = MAC_INT_STATUS_RMAC_INT; - temp64 = readq(&bar0->mac_int_mask); - temp64 &= ~((u64) val64); - writeq(temp64, &bar0->mac_int_mask); - - val64 = readq(&bar0->mac_rmac_err_mask); - val64 &= ~((u64) RMAC_LINK_STATE_CHANGE_INT); - writeq(val64, &bar0->mac_rmac_err_mask); } else if (flag == DISABLE_INTRS) { /* * Disable MAC Intrs in the general intr mask register @@ -1879,8 +1901,10 @@ static int start_nic(struct s2io_nic *nic) } /* Enable select interrupts */ - interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR | - RX_MAC_INTR | MC_INTR; + interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | MC_INTR; + interruptible |= TX_PIC_INTR | RX_PIC_INTR; + interruptible |= TX_MAC_INTR | RX_MAC_INTR; + en_dis_able_nic_intrs(nic, interruptible, ENABLE_INTRS); /* @@ -2004,8 +2028,9 @@ static void stop_nic(struct s2io_nic *nic) config = &nic->config; /* Disable all interrupts */ - interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | TX_MAC_INTR | - RX_MAC_INTR | MC_INTR; + interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | MC_INTR; + interruptible |= TX_PIC_INTR | RX_PIC_INTR; + interruptible |= TX_MAC_INTR | RX_MAC_INTR; en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS); /* Disable PRCs */ @@ -2618,10 +2643,12 @@ static void alarm_intr_handler(struct s2io_nic *nic) register u64 val64 = 0, err_reg = 0; /* Handling link status change error Intr */ - err_reg = readq(&bar0->mac_rmac_err_reg); - writeq(err_reg, &bar0->mac_rmac_err_reg); - if (err_reg & RMAC_LINK_STATE_CHANGE_INT) { - schedule_work(&nic->set_link_task); + if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) { + err_reg = readq(&bar0->mac_rmac_err_reg); + writeq(err_reg, &bar0->mac_rmac_err_reg); + if (err_reg & RMAC_LINK_STATE_CHANGE_INT) { + schedule_work(&nic->set_link_task); + } } /* Handling Ecc errors */ @@ -2947,7 +2974,7 @@ int s2io_open(struct net_device *dev) * Nic is initialized */ netif_carrier_off(dev); - sp->last_link_state = 0; /* Unkown link state */ + sp->last_link_state = LINK_DOWN; /* Initialize H/W and enable interrupts */ if (s2io_card_up(sp)) { @@ -3159,6 +3186,53 @@ s2io_alarm_handle(unsigned long data) mod_timer(&sp->alarm_timer, jiffies + HZ / 2); } +static void s2io_txpic_intr_handle(nic_t *sp) +{ + XENA_dev_config_t *bar0 = (XENA_dev_config_t *) sp->bar0; + u64 val64; + + val64 = readq(&bar0->pic_int_status); + if (val64 & PIC_INT_GPIO) { + val64 = readq(&bar0->gpio_int_reg); + if ((val64 & GPIO_INT_REG_LINK_DOWN) && + (val64 & GPIO_INT_REG_LINK_UP)) { + val64 |= GPIO_INT_REG_LINK_DOWN; + val64 |= GPIO_INT_REG_LINK_UP; + writeq(val64, &bar0->gpio_int_reg); + goto masking; + } + + if (((sp->last_link_state == LINK_UP) && + (val64 & GPIO_INT_REG_LINK_DOWN)) || + ((sp->last_link_state == LINK_DOWN) && + (val64 & GPIO_INT_REG_LINK_UP))) { + val64 = readq(&bar0->gpio_int_mask); + val64 |= GPIO_INT_MASK_LINK_DOWN; + val64 |= GPIO_INT_MASK_LINK_UP; + writeq(val64, &bar0->gpio_int_mask); + s2io_set_link((unsigned long)sp); + } +masking: + if (sp->last_link_state == LINK_UP) { + /*enable down interrupt */ + val64 = readq(&bar0->gpio_int_mask); + /* unmasks link down intr */ + val64 &= ~GPIO_INT_MASK_LINK_DOWN; + /* masks link up intr */ + val64 |= GPIO_INT_MASK_LINK_UP; + writeq(val64, &bar0->gpio_int_mask); + } else { + /*enable UP Interrupt */ + val64 = readq(&bar0->gpio_int_mask); + /* unmasks link up interrupt */ + val64 &= ~GPIO_INT_MASK_LINK_UP; + /* masks link down interrupt */ + val64 |= GPIO_INT_MASK_LINK_DOWN; + writeq(val64, &bar0->gpio_int_mask); + } + } +} + /** * s2io_isr - ISR handler of the device . * @irq: the irq of the device. @@ -3241,6 +3315,8 @@ static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs) tx_intr_handler(&mac_control->fifos[i]); } + if (reason & GEN_INTR_TXPIC) + s2io_txpic_intr_handle(sp); /* * If the Rx buffer count is below the panic threshold then * reallocate the buffers from the interrupt handler itself, @@ -4644,11 +4720,13 @@ static void s2io_set_link(unsigned long data) } subid = nic->pdev->subsystem_device; - /* - * Allow a small delay for the NICs self initiated - * cleanup to complete. - */ - msleep(100); + if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) { + /* + * Allow a small delay for the NICs self initiated + * cleanup to complete. + */ + msleep(100); + } val64 = readq(&bar0->adapter_status); if (verify_xena_quiescence(nic, val64, nic->device_enabled_once)) { @@ -4666,13 +4744,16 @@ static void s2io_set_link(unsigned long data) val64 |= ADAPTER_LED_ON; writeq(val64, &bar0->adapter_control); } - val64 = readq(&bar0->adapter_status); - if (!LINK_IS_UP(val64)) { - DBG_PRINT(ERR_DBG, "%s:", dev->name); - DBG_PRINT(ERR_DBG, " Link down"); - DBG_PRINT(ERR_DBG, "after "); - DBG_PRINT(ERR_DBG, "enabling "); - DBG_PRINT(ERR_DBG, "device \n"); + if (s2io_link_fault_indication(nic) == + MAC_RMAC_ERR_TIMER) { + val64 = readq(&bar0->adapter_status); + if (!LINK_IS_UP(val64)) { + DBG_PRINT(ERR_DBG, "%s:", dev->name); + DBG_PRINT(ERR_DBG, " Link down"); + DBG_PRINT(ERR_DBG, "after "); + DBG_PRINT(ERR_DBG, "enabling "); + DBG_PRINT(ERR_DBG, "device \n"); + } } if (nic->device_enabled_once == FALSE) { nic->device_enabled_once = TRUE; -- cgit v0.10.2 From 0b1f7ebe455ba4f1f46e7024150eeddbbf08addc Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:39:56 -0700 Subject: [PATCH] S2io: Miscellaneous fixes Hi, The last patch in this series fixes the following issues found during testing. 1. Ensure we don't pass zero sized buffers to the card(which can lockup) 2. Restore the PCI-X parameters(in case of Xframe I adapter) after a reset. 3. Make sure total size of all FIFOs does not exceed 8192. Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index e7c4285..abf910e 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -365,10 +365,9 @@ static int init_shared_mem(struct s2io_nic *nic) size += config->tx_cfg[i].fifo_len; } if (size > MAX_AVAILABLE_TXDS) { - DBG_PRINT(ERR_DBG, "%s: Total number of Tx FIFOs ", - dev->name); - DBG_PRINT(ERR_DBG, "exceeds the maximum value "); - DBG_PRINT(ERR_DBG, "that can be used\n"); + DBG_PRINT(ERR_DBG, "%s: Requested TxDs too high, ", + __FUNCTION__); + DBG_PRINT(ERR_DBG, "Requested: %d, max supported: 8192\n", size); return FAILURE; } @@ -611,8 +610,9 @@ static void free_shared_mem(struct s2io_nic *nic) lst_per_page); for (j = 0; j < page_num; j++) { int mem_blks = (j * lst_per_page); - if (!mac_control->fifos[i].list_info[mem_blks]. - list_virt_addr) + if ((!mac_control->fifos[i].list_info) || + (!mac_control->fifos[i].list_info[mem_blks]. + list_virt_addr)) break; pci_free_consistent(nic->pdev, PAGE_SIZE, mac_control->fifos[i]. @@ -2594,6 +2594,8 @@ static void tx_intr_handler(fifo_info_t *fifo_data) for (j = 0; j < frg_cnt; j++, txdlp++) { skb_frag_t *frag = &skb_shinfo(skb)->frags[j]; + if (!txdlp->Buffer_Pointer) + break; pci_unmap_page(nic->pdev, (dma_addr_t) txdlp-> @@ -2744,6 +2746,10 @@ void s2io_reset(nic_t * sp) u64 val64; u16 subid, pci_cmd; + /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */ + if (sp->device_type == XFRAME_I_DEVICE) + pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd)); + val64 = SW_RESET_ALL; writeq(val64, &bar0->sw_reset); @@ -2762,8 +2768,10 @@ void s2io_reset(nic_t * sp) msleep(250); if (!(sp->device_type & XFRAME_II_DEVICE)) { - /* Restore the PCI state saved during initializarion. */ + /* Restore the PCI state saved during initializarion. */ pci_restore_state(sp->pdev); + pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, + pci_cmd); } else { pci_set_master(sp->pdev); } @@ -2974,7 +2982,7 @@ int s2io_open(struct net_device *dev) * Nic is initialized */ netif_carrier_off(dev); - sp->last_link_state = LINK_DOWN; + sp->last_link_state = 0; /* Initialize H/W and enable interrupts */ if (s2io_card_up(sp)) { @@ -3102,6 +3110,15 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) spin_unlock_irqrestore(&sp->tx_lock, flags); return 0; } + + /* A buffer with no data will be dropped */ + if (!skb->len) { + DBG_PRINT(TX_DBG, "%s:Buffer has no data..\n", dev->name); + dev_kfree_skb(skb); + spin_unlock_irqrestore(&sp->tx_lock, flags); + return 0; + } + #ifdef NETIF_F_TSO mss = skb_shinfo(skb)->tso_size; if (mss) { @@ -3136,6 +3153,9 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) /* For fragmented SKB. */ for (i = 0; i < frg_cnt; i++) { skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + /* A '0' length fragment will be ignored */ + if (!frag->size) + continue; txdp++; txdp->Buffer_Pointer = (u64) pci_map_page (sp->pdev, frag->page, frag->page_offset, @@ -5257,7 +5277,8 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) config = &sp->config; /* Tx side parameters. */ - tx_fifo_len[0] = DEFAULT_FIFO_LEN; /* Default value. */ + if (tx_fifo_len[0] == 0) + tx_fifo_len[0] = DEFAULT_FIFO_LEN; /* Default value. */ config->tx_fifo_num = tx_fifo_num; for (i = 0; i < MAX_TX_FIFOS; i++) { config->tx_cfg[i].fifo_len = tx_fifo_len[i]; @@ -5280,7 +5301,8 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) config->max_txds = MAX_SKB_FRAGS; /* Rx side parameters. */ - rx_ring_sz[0] = SMALL_BLK_CNT; /* Default value. */ + if (rx_ring_sz[0] == 0) + rx_ring_sz[0] = SMALL_BLK_CNT; /* Default value. */ config->rx_ring_num = rx_ring_num; for (i = 0; i < MAX_RX_RINGS; i++) { config->rx_cfg[i].num_rxd = rx_ring_sz[i] * @@ -5310,7 +5332,7 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) /* initialize the shared memory used by the NIC and the host */ if (init_shared_mem(sp)) { DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n", - dev->name); + __FUNCTION__); ret = -ENOMEM; goto mem_alloc_failed; } @@ -5488,7 +5510,7 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) sp->def_mac_addr[0].mac_addr[3], sp->def_mac_addr[0].mac_addr[4], sp->def_mac_addr[0].mac_addr[5]); - int mode = s2io_print_pci_mode(sp); + mode = s2io_print_pci_mode(sp); if (mode < 0) { DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode "); ret = -EBADSLT; -- cgit v0.10.2 From 303bcb4b675d7284a1097dd1c18c995c0179883a Mon Sep 17 00:00:00 2001 From: "raghavendra.koushik@neterion.com" Date: Wed, 3 Aug 2005 12:41:38 -0700 Subject: [PATCH] S2io: Errors found during review Hi, This is a patch to incorporate comments from earlier 12 patches. It also fixes a few issues we found during this time. Following is a list of changes in this patch. Item 1 incorporates earlier comments. Issues addressed in items 2 to 4 were discovered recently. 1. wmb() call in s2io_xmit() replaced with mmiowb(). 2. The dtx_control register was earlier programmed incorrectly for Xframe II adapter. 3. As suggested by hardware team, after a reset, in case of Xframe II adapter, we clear certain spurious errors by clearing PCI-X ECC status register, "detected parity error" bit in PCI_STATUS register and PCI_STATUS bit in txpic_int register. 4. On IBM PPC platforms, we found that in the Rx buffer replenish function, two memory writes(one to the the descriptor length and another to the ownership) were getting reordered. This was causing the adapter to see the ownership transfered to it before the length was updated. One solution was to add a wmb() but since this would turnout expensive on some platforms if called for every descriptor, we set the ownership bit and other fields of '2' to 'N' Rx descriptors followed by a wmb() and then set the ownership of first descriptor ('1'). Here the value 'N' is configurable by making it a module loadable parameter (rxsync_frequency). (NOTE: This parameter is a power of 2). 5. Bumped up the driver version no. to 2.0.2.1 Signed-off-by: Ravinandan Arakali Signed-off-by: Raghavendra Koushik Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index abf910e..e083351 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -67,7 +67,7 @@ /* S2io Driver name & version. */ static char s2io_driver_name[] = "Neterion"; -static char s2io_driver_version[] = "Version 2.0.2.0"; +static char s2io_driver_version[] = "Version 2.0.2.1"; static inline int RXD_IS_UP2DT(RxD_t *rxdp) { @@ -301,6 +301,8 @@ static unsigned int bimodal = 0; #ifndef CONFIG_S2IO_NAPI static unsigned int indicate_max_pkts; #endif +/* Frequency of Rx desc syncs expressed as power of 2 */ +static unsigned int rxsync_frequency = 3; /* * S2IO device table. @@ -837,7 +839,7 @@ static int init_nic(struct s2io_nic *nic) */ if (nic->device_type & XFRAME_II_DEVICE) { while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) { - SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt], + SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt], &bar0->dtx_control, UF); if (dtx_cnt & 0x1) msleep(1); /* Necessary!! */ @@ -2083,6 +2085,7 @@ int fill_rx_buffers(struct s2io_nic *nic, int ring_no) #ifndef CONFIG_S2IO_NAPI unsigned long flags; #endif + RxD_t *first_rxdp = NULL; mac_control = &nic->mac_control; config = &nic->config; @@ -2202,6 +2205,10 @@ int fill_rx_buffers(struct s2io_nic *nic, int ring_no) if (!skb) { DBG_PRINT(ERR_DBG, "%s: Out of ", dev->name); DBG_PRINT(ERR_DBG, "memory to allocate SKBs\n"); + if (first_rxdp) { + wmb(); + first_rxdp->Control_1 |= RXD_OWN_XENA; + } return -ENOMEM; } #ifndef CONFIG_2BUFF_MODE @@ -2212,7 +2219,8 @@ int fill_rx_buffers(struct s2io_nic *nic, int ring_no) rxdp->Control_2 &= (~MASK_BUFFER0_SIZE); rxdp->Control_2 |= SET_BUFFER0_SIZE(size); rxdp->Host_Control = (unsigned long) (skb); - rxdp->Control_1 |= RXD_OWN_XENA; + if (alloc_tab & ((1 << rxsync_frequency) - 1)) + rxdp->Control_1 |= RXD_OWN_XENA; off++; off %= (MAX_RXDS_PER_BLOCK + 1); mac_control->rings[ring_no].rx_curr_put_info.offset = off; @@ -2239,17 +2247,34 @@ int fill_rx_buffers(struct s2io_nic *nic, int ring_no) rxdp->Control_2 |= SET_BUFFER1_SIZE(1); /* dummy. */ rxdp->Control_2 |= BIT(0); /* Set Buffer_Empty bit. */ rxdp->Host_Control = (u64) ((unsigned long) (skb)); - rxdp->Control_1 |= RXD_OWN_XENA; + if (alloc_tab & ((1 << rxsync_frequency) - 1)) + rxdp->Control_1 |= RXD_OWN_XENA; off++; mac_control->rings[ring_no].rx_curr_put_info.offset = off; #endif rxdp->Control_2 |= SET_RXD_MARKER; + if (!(alloc_tab & ((1 << rxsync_frequency) - 1))) { + if (first_rxdp) { + wmb(); + first_rxdp->Control_1 |= RXD_OWN_XENA; + } + first_rxdp = rxdp; + } atomic_inc(&nic->rx_bufs_left[ring_no]); alloc_tab++; } end: + /* Transfer ownership of first descriptor to adapter just before + * exiting. Before that, use memory barrier so that ownership + * and other fields are seen by adapter correctly. + */ + if (first_rxdp) { + wmb(); + first_rxdp->Control_1 |= RXD_OWN_XENA; + } + return SUCCESS; } @@ -2783,16 +2808,16 @@ void s2io_reset(nic_t * sp) s2io_set_swapper(sp); /* Clear certain PCI/PCI-X fields after reset */ - pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd); - pci_cmd &= 0x7FFF; /* Clear parity err detect bit */ - pci_write_config_word(sp->pdev, PCI_COMMAND, pci_cmd); + if (sp->device_type == XFRAME_II_DEVICE) { + /* Clear parity err detect bit */ + pci_write_config_word(sp->pdev, PCI_STATUS, 0x8000); - val64 = readq(&bar0->txpic_int_reg); - val64 &= ~BIT(62); /* Clearing PCI_STATUS error reflected here */ - writeq(val64, &bar0->txpic_int_reg); + /* Clearing PCIX Ecc status register */ + pci_write_config_dword(sp->pdev, 0x68, 0x7C); - /* Clearing PCIX Ecc status register */ - pci_write_config_dword(sp->pdev, 0x68, 0); + /* Clearing PCI_STATUS error reflected here */ + writeq(BIT(62), &bar0->txpic_int_reg); + } /* Reset device statistics maintained by OS */ memset(&sp->stats, 0, sizeof (struct net_device_stats)); @@ -3168,8 +3193,6 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) val64 = mac_control->fifos[queue].list_info[put_off].list_phy_addr; writeq(val64, &tx_fifo->TxDL_Pointer); - wmb(); - val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST | TX_FIFO_LAST_LIST); @@ -3179,6 +3202,8 @@ int s2io_xmit(struct sk_buff *skb, struct net_device *dev) #endif writeq(val64, &tx_fifo->List_Control); + mmiowb(); + put_off++; put_off %= mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1; mac_control->fifos[queue].tx_curr_put_info.offset = put_off; @@ -5172,6 +5197,7 @@ module_param(bimodal, bool, 0); #ifndef CONFIG_S2IO_NAPI module_param(indicate_max_pkts, int, 0); #endif +module_param(rxsync_frequency, int, 0); /** * s2io_init_nic - Initialization of the adapter . diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index 9463145..5d92707 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -13,11 +13,6 @@ #ifndef _S2IO_H #define _S2IO_H -/* Enable 2 buffer mode by default for SGI system */ -#ifdef CONFIG_IA64_SGI_SN2 -#define CONFIG_2BUFF_MODE -#endif - #define TBD 0 #define BIT(loc) (0x8000000000000000ULL >> (loc)) #define vBIT(val, loc, sz) (((u64)val) << (64-loc-sz)) -- cgit v0.10.2 From 67c4f3fa25502ce7ed82fb0307e09cf36f1f81da Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Thu, 11 Aug 2005 02:07:25 -0400 Subject: Fix numerous minor problems with new phy subsystem. Includes fixes for problems noted by Adrian Bunk, Andrew Morton, and one other person lost in the annals of history (and email folders). diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index 8b5db23..c2f1bf1 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -5,7 +5,7 @@ menu "PHY device support" config PHYLIB - bool "PHY Device support and infrastructure" + tristate "PHY Device support and infrastructure" depends on NET_ETHERNET help Ethernet controllers are usually attached to PHY @@ -24,31 +24,31 @@ comment "MII PHY device drivers" depends on PHYLIB config MARVELL_PHY - bool "Drivers for Marvell PHYs" + tristate "Drivers for Marvell PHYs" depends on PHYLIB ---help--- Currently has a driver for the 88E1011S config DAVICOM_PHY - bool "Drivers for Davicom PHYs" + tristate "Drivers for Davicom PHYs" depends on PHYLIB ---help--- Currently supports dm9161e and dm9131 config QSEMI_PHY - bool "Drivers for Quality Semiconductor PHYs" + tristate "Drivers for Quality Semiconductor PHYs" depends on PHYLIB ---help--- Currently supports the qs6612 config LXT_PHY - bool "Drivers for the Intel LXT PHYs" + tristate "Drivers for the Intel LXT PHYs" depends on PHYLIB ---help--- Currently supports the lxt970, lxt971 config CICADA_PHY - bool "Drivers for the Cicada PHYs" + tristate "Drivers for the Cicada PHYs" depends on PHYLIB ---help--- Currently supports the cis8204 diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index 1af05de..fb7cb38 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -1,9 +1,9 @@ # Makefile for Linux PHY drivers -obj-$(CONFIG_PHYLIB) += phy.o phy_device.o mdio_bus.o +libphy-objs := phy.o phy_device.o mdio_bus.o -obj-$(CONFIG_MARVELL_PHY) += marvell.o -obj-$(CONFIG_DAVICOM_PHY) += davicom.o -obj-$(CONFIG_CICADA_PHY) += cicada.o -obj-$(CONFIG_LXT_PHY) += lxt.o -obj-$(CONFIG_QSEMI_PHY) += qsemi.o +obj-$(CONFIG_MARVELL_PHY) += libphy.o marvell.o +obj-$(CONFIG_DAVICOM_PHY) += libphy.o davicom.o +obj-$(CONFIG_CICADA_PHY) += libphy.o cicada.o +obj-$(CONFIG_LXT_PHY) += libphy.o lxt.o +obj-$(CONFIG_QSEMI_PHY) += libphy.o qsemi.o diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index e75103b..5fbea6a 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -165,9 +165,9 @@ struct bus_type mdio_bus_type = { .resume = mdio_bus_resume, }; -static int __init mdio_bus_init(void) +int __init mdio_bus_init(void) { return bus_register(&mdio_bus_type); } -subsys_initcall(mdio_bus_init); + diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index e2c6896..934065d 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -39,7 +39,6 @@ #include #include -static void phy_change(void *data); static void phy_timer(unsigned long data); /* Convenience function to print out the current phy status @@ -464,7 +463,6 @@ void phy_stop_machine(struct phy_device *phydev) phydev->adjust_state = NULL; } -#ifdef CONFIG_PHYCONTROL /* phy_error: * * Moves the PHY to the HALTED state in response to a read @@ -479,6 +477,10 @@ void phy_error(struct phy_device *phydev) spin_unlock(&phydev->lock); } +#ifdef CONFIG_PHYCONTROL + +static void phy_change(void *data); + /* phy_interrupt * * description: When a PHY interrupt occurs, the handler disables @@ -672,6 +674,8 @@ void phy_start(struct phy_device *phydev) EXPORT_SYMBOL(phy_stop); EXPORT_SYMBOL(phy_start); +#endif /* CONFIG_PHYCONTROL */ + /* PHY timer which handles the state machine */ static void phy_timer(unsigned long data) { @@ -859,4 +863,3 @@ static void phy_timer(unsigned long data) mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ); } -#endif /* CONFIG_PHYCONTROL */ diff --git a/drivers/net/phy/phy.c.orig b/drivers/net/phy/phy.c.orig deleted file mode 100644 index 6af17ce..0000000 --- a/drivers/net/phy/phy.c.orig +++ /dev/null @@ -1,860 +0,0 @@ -/* - * drivers/net/phy/phy.c - * - * Framework for configuring and reading PHY devices - * Based on code in sungem_phy.c and gianfar_phy.c - * - * Author: Andy Fleming - * - * Copyright (c) 2004 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -static void phy_change(void *data); -static void phy_timer(unsigned long data); - -/* Convenience function to print out the current phy status - */ -void phy_print_status(struct phy_device *phydev) -{ - pr_info("%s: Link is %s", phydev->dev.bus_id, - phydev->link ? "Up" : "Down"); - if (phydev->link) - printk(" - %d/%s", phydev->speed, - DUPLEX_FULL == phydev->duplex ? - "Full" : "Half"); - - printk("\n"); -} -EXPORT_SYMBOL(phy_print_status); - - -/* Convenience functions for reading/writing a given PHY - * register. They MUST NOT be called from interrupt context, - * because the bus read/write functions may wait for an interrupt - * to conclude the operation. */ -int phy_read(struct phy_device *phydev, u16 regnum) -{ - int retval; - struct mii_bus *bus = phydev->bus; - - spin_lock_bh(&bus->mdio_lock); - retval = bus->read(bus, phydev->addr, regnum); - spin_unlock_bh(&bus->mdio_lock); - - return retval; -} -EXPORT_SYMBOL(phy_read); - -int phy_write(struct phy_device *phydev, u16 regnum, u16 val) -{ - int err; - struct mii_bus *bus = phydev->bus; - - spin_lock_bh(&bus->mdio_lock); - err = bus->write(bus, phydev->addr, regnum, val); - spin_unlock_bh(&bus->mdio_lock); - - return err; -} -EXPORT_SYMBOL(phy_write); - - -int phy_clear_interrupt(struct phy_device *phydev) -{ - int err = 0; - - if (phydev->drv->ack_interrupt) - err = phydev->drv->ack_interrupt(phydev); - - return err; -} - - -int phy_config_interrupt(struct phy_device *phydev, u32 interrupts) -{ - int err = 0; - - phydev->interrupts = interrupts; - if (phydev->drv->config_intr) - err = phydev->drv->config_intr(phydev); - - return err; -} - - -/* phy_aneg_done - * - * description: Reads the status register and returns 0 either if - * auto-negotiation is incomplete, or if there was an error. - * Returns BMSR_ANEGCOMPLETE if auto-negotiation is done. - */ -static inline int phy_aneg_done(struct phy_device *phydev) -{ - int retval; - - retval = phy_read(phydev, MII_BMSR); - - return (retval < 0) ? retval : (retval & BMSR_ANEGCOMPLETE); -} - -/* phy_start_aneg - * - * description: Calls the PHY driver's config_aneg, and then - * sets the PHY state to PHY_AN if auto-negotiation is enabled, - * and to PHY_FORCING if auto-negotiation is disabled. Unless - * the PHY is currently HALTED. - */ -int phy_start_aneg(struct phy_device *phydev) -{ - int err; - - spin_lock(&phydev->lock); - - if (AUTONEG_DISABLE == phydev->autoneg) - phy_sanitize_settings(phydev); - - err = phydev->drv->config_aneg(phydev); - - if (err < 0) - goto out_unlock; - - if (phydev->state != PHY_HALTED) { - if (AUTONEG_ENABLE == phydev->autoneg) { - phydev->state = PHY_AN; - phydev->link_timeout = PHY_AN_TIMEOUT; - } else { - phydev->state = PHY_FORCING; - phydev->link_timeout = PHY_FORCE_TIMEOUT; - } - } - -out_unlock: - spin_unlock(&phydev->lock); - return err; -} -EXPORT_SYMBOL(phy_start_aneg); - - -/* A structure for mapping a particular speed and duplex - * combination to a particular SUPPORTED and ADVERTISED value */ -struct phy_setting { - int speed; - int duplex; - u32 setting; -}; - -/* A mapping of all SUPPORTED settings to speed/duplex */ -static struct phy_setting settings[] = { - { - .speed = 10000, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_10000baseT_Full, - }, - { - .speed = SPEED_1000, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_1000baseT_Full, - }, - { - .speed = SPEED_1000, - .duplex = DUPLEX_HALF, - .setting = SUPPORTED_1000baseT_Half, - }, - { - .speed = SPEED_100, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_100baseT_Full, - }, - { - .speed = SPEED_100, - .duplex = DUPLEX_HALF, - .setting = SUPPORTED_100baseT_Half, - }, - { - .speed = SPEED_10, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_10baseT_Full, - }, - { - .speed = SPEED_10, - .duplex = DUPLEX_HALF, - .setting = SUPPORTED_10baseT_Half, - }, -}; - -#define MAX_NUM_SETTINGS (sizeof(settings)/sizeof(struct phy_setting)) - -/* phy_find_setting - * - * description: Searches the settings array for the setting which - * matches the desired speed and duplex, and returns the index - * of that setting. Returns the index of the last setting if - * none of the others match. - */ -static inline int phy_find_setting(int speed, int duplex) -{ - int idx = 0; - - while (idx < ARRAY_SIZE(settings) && - (settings[idx].speed != speed || - settings[idx].duplex != duplex)) - idx++; - - return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; -} - -/* phy_find_valid - * idx: The first index in settings[] to search - * features: A mask of the valid settings - * - * description: Returns the index of the first valid setting less - * than or equal to the one pointed to by idx, as determined by - * the mask in features. Returns the index of the last setting - * if nothing else matches. - */ -static inline int phy_find_valid(int idx, u32 features) -{ - while (idx < MAX_NUM_SETTINGS && !(settings[idx].setting & features)) - idx++; - - return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; -} - -/* phy_sanitize_settings - * - * description: Make sure the PHY is set to supported speeds and - * duplexes. Drop down by one in this order: 1000/FULL, - * 1000/HALF, 100/FULL, 100/HALF, 10/FULL, 10/HALF - */ -void phy_sanitize_settings(struct phy_device *phydev) -{ - u32 features = phydev->supported; - int idx; - - /* Sanitize settings based on PHY capabilities */ - if ((features & SUPPORTED_Autoneg) == 0) - phydev->autoneg = 0; - - idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex), - features); - - phydev->speed = settings[idx].speed; - phydev->duplex = settings[idx].duplex; -} -EXPORT_SYMBOL(phy_sanitize_settings); - -/* phy_force_reduction - * - * description: Reduces the speed/duplex settings by - * one notch. The order is so: - * 1000/FULL, 1000/HALF, 100/FULL, 100/HALF, - * 10/FULL, 10/HALF. The function bottoms out at 10/HALF. - */ -static void phy_force_reduction(struct phy_device *phydev) -{ - int idx; - - idx = phy_find_setting(phydev->speed, phydev->duplex); - - idx++; - - idx = phy_find_valid(idx, phydev->supported); - - phydev->speed = settings[idx].speed; - phydev->duplex = settings[idx].duplex; - - pr_info("Trying %d/%s\n", phydev->speed, - DUPLEX_FULL == phydev->duplex ? - "FULL" : "HALF"); -} - -/* phy_ethtool_sset: - * A generic ethtool sset function. Handles all the details - * - * A few notes about parameter checking: - * - We don't set port or transceiver, so we don't care what they - * were set to. - * - phy_start_aneg() will make sure forced settings are sane, and - * choose the next best ones from the ones selected, so we don't - * care if ethtool tries to give us bad values - */ -int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd) -{ - if (cmd->phy_address != phydev->addr) - return -EINVAL; - - /* We make sure that we don't pass unsupported - * values in to the PHY */ - cmd->advertising &= phydev->supported; - - /* Verify the settings we care about. */ - if (cmd->autoneg != AUTONEG_ENABLE && cmd->autoneg != AUTONEG_DISABLE) - return -EINVAL; - - if (cmd->autoneg == AUTONEG_ENABLE && cmd->advertising == 0) - return -EINVAL; - - if (cmd->autoneg == AUTONEG_DISABLE - && ((cmd->speed != SPEED_1000 - && cmd->speed != SPEED_100 - && cmd->speed != SPEED_10) - || (cmd->duplex != DUPLEX_HALF - && cmd->duplex != DUPLEX_FULL))) - return -EINVAL; - - phydev->autoneg = cmd->autoneg; - - phydev->speed = cmd->speed; - - phydev->advertising = cmd->advertising; - - if (AUTONEG_ENABLE == cmd->autoneg) - phydev->advertising |= ADVERTISED_Autoneg; - else - phydev->advertising &= ~ADVERTISED_Autoneg; - - phydev->duplex = cmd->duplex; - - /* Restart the PHY */ - phy_start_aneg(phydev); - - return 0; -} - -int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd) -{ - cmd->supported = phydev->supported; - - cmd->advertising = phydev->advertising; - - cmd->speed = phydev->speed; - cmd->duplex = phydev->duplex; - cmd->port = PORT_MII; - cmd->phy_address = phydev->addr; - cmd->transceiver = XCVR_EXTERNAL; - cmd->autoneg = phydev->autoneg; - - return 0; -} - - -/* Note that this function is currently incompatible with the - * PHYCONTROL layer. It changes registers without regard to - * current state. Use at own risk - */ -int phy_mii_ioctl(struct phy_device *phydev, - struct mii_ioctl_data *mii_data, int cmd) -{ - u16 val = mii_data->val_in; - - switch (cmd) { - case SIOCGMIIPHY: - mii_data->phy_id = phydev->addr; - break; - case SIOCGMIIREG: - mii_data->val_out = phy_read(phydev, mii_data->reg_num); - break; - - case SIOCSMIIREG: - if (!capable(CAP_NET_ADMIN)) - return -EPERM; - - if (mii_data->phy_id == phydev->addr) { - switch(mii_data->reg_num) { - case MII_BMCR: - if (val & (BMCR_RESET|BMCR_ANENABLE)) - phydev->autoneg = AUTONEG_DISABLE; - else - phydev->autoneg = AUTONEG_ENABLE; - if ((!phydev->autoneg) && (val & BMCR_FULLDPLX)) - phydev->duplex = DUPLEX_FULL; - else - phydev->duplex = DUPLEX_HALF; - break; - case MII_ADVERTISE: - phydev->advertising = val; - break; - default: - /* do nothing */ - break; - } - } - - phy_write(phydev, mii_data->reg_num, val); - - if (mii_data->reg_num == MII_BMCR - && val & BMCR_RESET - && phydev->drv->config_init) - phydev->drv->config_init(phydev); - break; - } - - return 0; -} - -/* phy_start_machine: - * - * description: The PHY infrastructure can run a state machine - * which tracks whether the PHY is starting up, negotiating, - * etc. This function starts the timer which tracks the state - * of the PHY. If you want to be notified when the state - * changes, pass in the callback, otherwise, pass NULL. If you - * want to maintain your own state machine, do not call this - * function. */ -void phy_start_machine(struct phy_device *phydev, - void (*handler)(struct net_device *)) -{ - phydev->adjust_state = handler; - - init_timer(&phydev->phy_timer); - phydev->phy_timer.function = &phy_timer; - phydev->phy_timer.data = (unsigned long) phydev; - mod_timer(&phydev->phy_timer, jiffies + HZ); -} - -/* phy_stop_machine - * - * description: Stops the state machine timer, sets the state to - * UP (unless it wasn't up yet), and then frees the interrupt, - * if it is in use. This function must be called BEFORE - * phy_detach. - */ -void phy_stop_machine(struct phy_device *phydev) -{ - del_timer_sync(&phydev->phy_timer); - - spin_lock(&phydev->lock); - if (phydev->state > PHY_UP) - phydev->state = PHY_UP; - spin_unlock(&phydev->lock); - - if (phydev->irq != PHY_POLL) - phy_stop_interrupts(phydev); - - phydev->adjust_state = NULL; -} - -#ifdef CONFIG_PHYCONTROL -/* phy_error: - * - * Moves the PHY to the HALTED state in response to a read - * or write error, and tells the controller the link is down. - * Must not be called from interrupt context, or while the - * phydev->lock is held. - */ -void phy_error(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - phydev->state = PHY_HALTED; - spin_unlock(&phydev->lock); -} - -/* phy_interrupt - * - * description: When a PHY interrupt occurs, the handler disables - * interrupts, and schedules a work task to clear the interrupt. - */ -static irqreturn_t phy_interrupt(int irq, void *phy_dat, struct pt_regs *regs) -{ - struct phy_device *phydev = phy_dat; - - /* The MDIO bus is not allowed to be written in interrupt - * context, so we need to disable the irq here. A work - * queue will write the PHY to disable and clear the - * interrupt, and then reenable the irq line. */ - disable_irq_nosync(irq); - - schedule_work(&phydev->phy_queue); - - return IRQ_HANDLED; -} - -/* Enable the interrupts from the PHY side */ -int phy_enable_interrupts(struct phy_device *phydev) -{ - int err; - - err = phy_clear_interrupt(phydev); - - if (err < 0) - return err; - - err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); - - return err; -} - -/* Disable the PHY interrupts from the PHY side */ -int phy_disable_interrupts(struct phy_device *phydev) -{ - int err; - - /* Disable PHY interrupts */ - err = phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); - - if (err) - goto phy_err; - - /* Clear the interrupt */ - err = phy_clear_interrupt(phydev); - - if (err) - goto phy_err; - - return 0; - -phy_err: - phy_error(phydev); - - return err; -} - -/* phy_start_interrupts - * - * description: Request the interrupt for the given PHY. If - * this fails, then we set irq to PHY_POLL. - * Otherwise, we enable the interrupts in the PHY. - * Returns 0 on success. - * This should only be called with a valid IRQ number. - */ -int phy_start_interrupts(struct phy_device *phydev) -{ - int err = 0; - - INIT_WORK(&phydev->phy_queue, phy_change, phydev); - - if (request_irq(phydev->irq, phy_interrupt, - SA_SHIRQ, - "phy_interrupt", - phydev) < 0) { - printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n", - phydev->bus->name, - phydev->irq); - phydev->irq = PHY_POLL; - return 0; - } - - err = phy_enable_interrupts(phydev); - - return err; -} -EXPORT_SYMBOL(phy_start_interrupts); - -int phy_stop_interrupts(struct phy_device *phydev) -{ - int err; - - err = phy_disable_interrupts(phydev); - - if (err) - phy_error(phydev); - - free_irq(phydev->irq, phydev); - - return err; -} -EXPORT_SYMBOL(phy_stop_interrupts); - - -/* Scheduled by the phy_interrupt/timer to handle PHY changes */ -static void phy_change(void *data) -{ - int err; - struct phy_device *phydev = data; - - err = phy_disable_interrupts(phydev); - - if (err) - goto phy_err; - - spin_lock(&phydev->lock); - if ((PHY_RUNNING == phydev->state) || (PHY_NOLINK == phydev->state)) - phydev->state = PHY_CHANGELINK; - spin_unlock(&phydev->lock); - - enable_irq(phydev->irq); - - /* Reenable interrupts */ - err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); - - if (err) - goto irq_enable_err; - - return; - -irq_enable_err: - disable_irq(phydev->irq); -phy_err: - phy_error(phydev); -} - -/* Bring down the PHY link, and stop checking the status. */ -void phy_stop(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - - if (PHY_HALTED == phydev->state) - goto out_unlock; - - if (phydev->irq != PHY_POLL) { - /* Clear any pending interrupts */ - phy_clear_interrupt(phydev); - - /* Disable PHY Interrupts */ - phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); - } - - phydev->state = PHY_HALTED; - -out_unlock: - spin_unlock(&phydev->lock); -} - - -/* phy_start - * - * description: Indicates the attached device's readiness to - * handle PHY-related work. Used during startup to start the - * PHY, and after a call to phy_stop() to resume operation. - * Also used to indicate the MDIO bus has cleared an error - * condition. - */ -void phy_start(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - - switch (phydev->state) { - case PHY_STARTING: - phydev->state = PHY_PENDING; - break; - case PHY_READY: - phydev->state = PHY_UP; - break; - case PHY_HALTED: - phydev->state = PHY_RESUMING; - default: - break; - } - spin_unlock(&phydev->lock); -} -EXPORT_SYMBOL(phy_stop); -EXPORT_SYMBOL(phy_start); - -/* PHY timer which handles the state machine */ -static void phy_timer(unsigned long data) -{ - struct phy_device *phydev = (struct phy_device *)data; - int needs_aneg = 0; - int err = 0; - - spin_lock(&phydev->lock); - - if (phydev->adjust_state) - phydev->adjust_state(phydev->attached_dev); - - switch(phydev->state) { - case PHY_DOWN: - case PHY_STARTING: - case PHY_READY: - case PHY_PENDING: - break; - case PHY_UP: - needs_aneg = 1; - - phydev->link_timeout = PHY_AN_TIMEOUT; - - break; - case PHY_AN: - /* Check if negotiation is done. Break - * if there's an error */ - err = phy_aneg_done(phydev); - if (err < 0) - break; - - /* If auto-negotiation is done, we change to - * either RUNNING, or NOLINK */ - if (err > 0) { - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - } else { - phydev->state = PHY_NOLINK; - netif_carrier_off(phydev->attached_dev); - } - - phydev->adjust_link(phydev->attached_dev); - - } else if (0 == phydev->link_timeout--) { - /* The counter expired, so either we - * switch to forced mode, or the - * magic_aneg bit exists, and we try aneg - * again */ - if (!(phydev->drv->flags & PHY_HAS_MAGICANEG)) { - int idx; - - /* We'll start from the - * fastest speed, and work - * our way down */ - idx = phy_find_valid(0, - phydev->supported); - - phydev->speed = settings[idx].speed; - phydev->duplex = settings[idx].duplex; - - phydev->autoneg = AUTONEG_DISABLE; - phydev->state = PHY_FORCING; - phydev->link_timeout = - PHY_FORCE_TIMEOUT; - - pr_info("Trying %d/%s\n", - phydev->speed, - DUPLEX_FULL == - phydev->duplex ? - "FULL" : "HALF"); - } - - needs_aneg = 1; - } - break; - case PHY_NOLINK: - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - phydev->adjust_link(phydev->attached_dev); - } - break; - case PHY_FORCING: - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - } else { - if (0 == phydev->link_timeout--) { - phy_force_reduction(phydev); - needs_aneg = 1; - } - } - - phydev->adjust_link(phydev->attached_dev); - break; - case PHY_RUNNING: - /* Only register a CHANGE if we are - * polling */ - if (PHY_POLL == phydev->irq) - phydev->state = PHY_CHANGELINK; - break; - case PHY_CHANGELINK: - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - } else { - phydev->state = PHY_NOLINK; - netif_carrier_off(phydev->attached_dev); - } - - phydev->adjust_link(phydev->attached_dev); - - if (PHY_POLL != phydev->irq) - err = phy_config_interrupt(phydev, - PHY_INTERRUPT_ENABLED); - break; - case PHY_HALTED: - if (phydev->link) { - phydev->link = 0; - netif_carrier_off(phydev->attached_dev); - phydev->adjust_link(phydev->attached_dev); - } - break; - case PHY_RESUMING: - - err = phy_clear_interrupt(phydev); - - if (err) - break; - - err = phy_config_interrupt(phydev, - PHY_INTERRUPT_ENABLED); - - if (err) - break; - - if (AUTONEG_ENABLE == phydev->autoneg) { - err = phy_aneg_done(phydev); - if (err < 0) - break; - - /* err > 0 if AN is done. - * Otherwise, it's 0, and we're - * still waiting for AN */ - if (err > 0) { - phydev->state = PHY_RUNNING; - } else { - phydev->state = PHY_AN; - phydev->link_timeout = PHY_AN_TIMEOUT; - } - } else - phydev->state = PHY_RUNNING; - break; - } - - spin_unlock(&phydev->lock); - - if (needs_aneg) - err = phy_start_aneg(phydev); - - if (err < 0) - phy_error(phydev); - - mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ); -} - -#endif /* CONFIG_PHYCONTROL */ diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index f0595af..c111383 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -39,6 +39,19 @@ #include #include +static int genphy_config_init(struct phy_device *phydev); + +static struct phy_driver genphy_driver = { + .phy_id = 0xffffffff, + .phy_id_mask = 0xffffffff, + .name = "Generic PHY", + .config_init = genphy_config_init, + .features = 0, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .driver = {.owner = THIS_MODULE, }, +}; + /* get_phy_device * * description: Reads the ID registers of the PHY at addr on the @@ -656,27 +669,32 @@ void phy_driver_unregister(struct phy_driver *drv) } EXPORT_SYMBOL(phy_driver_unregister); -static struct phy_driver genphy_driver = { - .phy_id = 0xffffffff, - .phy_id_mask = 0xffffffff, - .name = "Generic PHY", - .config_init = genphy_config_init, - .features = 0, - .config_aneg = genphy_config_aneg, - .read_status = genphy_read_status, - .driver = {.owner = THIS_MODULE, }, -}; -static int __init genphy_init(void) +static int __init phy_init(void) { - return phy_driver_register(&genphy_driver); + int rc; + extern int mdio_bus_init(void); + + rc = phy_driver_register(&genphy_driver); + if (rc) + goto out; + + rc = mdio_bus_init(); + if (rc) + goto out_unreg; + return 0; + +out_unreg: + phy_driver_unregister(&genphy_driver); +out: + return rc; } -static void __exit genphy_exit(void) +static void __exit phy_exit(void) { phy_driver_unregister(&genphy_driver); } -module_init(genphy_init); -module_exit(genphy_exit); +module_init(phy_init); +module_exit(phy_exit); diff --git a/include/linux/phy.h b/include/linux/phy.h index 3404804..72cb67b 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -374,5 +374,4 @@ int phy_start_interrupts(struct phy_device *phydev); void phy_print_status(struct phy_device *phydev); extern struct bus_type mdio_bus_type; -extern struct phy_driver genphy_driver; #endif /* __PHY_H */ -- cgit v0.10.2 From 2bf69b5fe90b3246ab50064c5a690a363e8c53e2 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Thu, 11 Aug 2005 02:47:54 -0400 Subject: phy subsystem: more cleanups - unexport symbols never used outside of home module - remove dead code - remove CONFIG_PHYCONTROL, make it unconditionally enabled diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index c2f1bf1..6450bd7 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -12,14 +12,6 @@ config PHYLIB devices. This option provides infrastructure for managing PHY devices. -config PHYCONTROL - bool "Support for automatically handling PHY state changes" - depends on PHYLIB - help - Adds code to perform all the work for keeping PHY link - state (speed/duplex/etc) up-to-date. Also handles - interrupts. - comment "MII PHY device drivers" depends on PHYLIB diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index 5fbea6a..d5a05be 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -38,80 +38,6 @@ #include #include -/* mdiobus_register - * - * description: Called by a bus driver to bring up all the PHYs - * on a given bus, and attach them to the bus - */ -int mdiobus_register(struct mii_bus *bus) -{ - int i; - int err = 0; - - spin_lock_init(&bus->mdio_lock); - - if (NULL == bus || NULL == bus->name || - NULL == bus->read || - NULL == bus->write) - return -EINVAL; - - if (bus->reset) - bus->reset(bus); - - for (i = 0; i < PHY_MAX_ADDR; i++) { - struct phy_device *phydev; - - phydev = get_phy_device(bus, i); - - if (IS_ERR(phydev)) - return PTR_ERR(phydev); - - /* There's a PHY at this address - * We need to set: - * 1) IRQ - * 2) bus_id - * 3) parent - * 4) bus - * 5) mii_bus - * And, we need to register it */ - if (phydev) { - phydev->irq = bus->irq[i]; - - phydev->dev.parent = bus->dev; - phydev->dev.bus = &mdio_bus_type; - sprintf(phydev->dev.bus_id, "phy%d:%d", bus->id, i); - - phydev->bus = bus; - - err = device_register(&phydev->dev); - - if (err) - printk(KERN_ERR "phy %d failed to register\n", - i); - } - - bus->phy_map[i] = phydev; - } - - pr_info("%s: probed\n", bus->name); - - return err; -} -EXPORT_SYMBOL(mdiobus_register); - -void mdiobus_unregister(struct mii_bus *bus) -{ - int i; - - for (i = 0; i < PHY_MAX_ADDR; i++) { - if (bus->phy_map[i]) { - device_unregister(&bus->phy_map[i]->dev); - kfree(bus->phy_map[i]); - } - } -} -EXPORT_SYMBOL(mdiobus_unregister); - /* mdio_bus_match * * description: Given a PHY device, and a PHY driver, return 1 if diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 934065d..d3e43631 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -40,21 +40,9 @@ #include static void phy_timer(unsigned long data); - -/* Convenience function to print out the current phy status - */ -void phy_print_status(struct phy_device *phydev) -{ - pr_info("%s: Link is %s", phydev->dev.bus_id, - phydev->link ? "Up" : "Down"); - if (phydev->link) - printk(" - %d/%s", phydev->speed, - DUPLEX_FULL == phydev->duplex ? - "Full" : "Half"); - - printk("\n"); -} -EXPORT_SYMBOL(phy_print_status); +static int phy_disable_interrupts(struct phy_device *phydev); +static void phy_sanitize_settings(struct phy_device *phydev); +static int phy_stop_interrupts(struct phy_device *phydev); /* Convenience functions for reading/writing a given PHY @@ -133,7 +121,7 @@ static inline int phy_aneg_done(struct phy_device *phydev) * and to PHY_FORCING if auto-negotiation is disabled. Unless * the PHY is currently HALTED. */ -int phy_start_aneg(struct phy_device *phydev) +static int phy_start_aneg(struct phy_device *phydev) { int err; @@ -161,8 +149,6 @@ out_unlock: spin_unlock(&phydev->lock); return err; } -EXPORT_SYMBOL(phy_start_aneg); - /* A structure for mapping a particular speed and duplex * combination to a particular SUPPORTED and ADVERTISED value */ @@ -255,7 +241,7 @@ static inline int phy_find_valid(int idx, u32 features) * duplexes. Drop down by one in this order: 1000/FULL, * 1000/HALF, 100/FULL, 100/HALF, 10/FULL, 10/HALF */ -void phy_sanitize_settings(struct phy_device *phydev) +static void phy_sanitize_settings(struct phy_device *phydev) { u32 features = phydev->supported; int idx; @@ -270,7 +256,6 @@ void phy_sanitize_settings(struct phy_device *phydev) phydev->speed = settings[idx].speed; phydev->duplex = settings[idx].duplex; } -EXPORT_SYMBOL(phy_sanitize_settings); /* phy_force_reduction * @@ -477,48 +462,22 @@ void phy_error(struct phy_device *phydev) spin_unlock(&phydev->lock); } -#ifdef CONFIG_PHYCONTROL - -static void phy_change(void *data); - -/* phy_interrupt - * - * description: When a PHY interrupt occurs, the handler disables - * interrupts, and schedules a work task to clear the interrupt. - */ -static irqreturn_t phy_interrupt(int irq, void *phy_dat, struct pt_regs *regs) -{ - struct phy_device *phydev = phy_dat; - - /* The MDIO bus is not allowed to be written in interrupt - * context, so we need to disable the irq here. A work - * queue will write the PHY to disable and clear the - * interrupt, and then reenable the irq line. */ - disable_irq_nosync(irq); - - schedule_work(&phydev->phy_queue); - - return IRQ_HANDLED; -} - -/* Enable the interrupts from the PHY side */ -int phy_enable_interrupts(struct phy_device *phydev) +static int phy_stop_interrupts(struct phy_device *phydev) { int err; - err = phy_clear_interrupt(phydev); + err = phy_disable_interrupts(phydev); - if (err < 0) - return err; + if (err) + phy_error(phydev); - err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); + free_irq(phydev->irq, phydev); return err; } -EXPORT_SYMBOL(phy_enable_interrupts); /* Disable the PHY interrupts from the PHY side */ -int phy_disable_interrupts(struct phy_device *phydev) +static int phy_disable_interrupts(struct phy_device *phydev) { int err; @@ -541,140 +500,6 @@ phy_err: return err; } -EXPORT_SYMBOL(phy_disable_interrupts); - -/* phy_start_interrupts - * - * description: Request the interrupt for the given PHY. If - * this fails, then we set irq to PHY_POLL. - * Otherwise, we enable the interrupts in the PHY. - * Returns 0 on success. - * This should only be called with a valid IRQ number. - */ -int phy_start_interrupts(struct phy_device *phydev) -{ - int err = 0; - - INIT_WORK(&phydev->phy_queue, phy_change, phydev); - - if (request_irq(phydev->irq, phy_interrupt, - SA_SHIRQ, - "phy_interrupt", - phydev) < 0) { - printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n", - phydev->bus->name, - phydev->irq); - phydev->irq = PHY_POLL; - return 0; - } - - err = phy_enable_interrupts(phydev); - - return err; -} -EXPORT_SYMBOL(phy_start_interrupts); - -int phy_stop_interrupts(struct phy_device *phydev) -{ - int err; - - err = phy_disable_interrupts(phydev); - - if (err) - phy_error(phydev); - - free_irq(phydev->irq, phydev); - - return err; -} -EXPORT_SYMBOL(phy_stop_interrupts); - - -/* Scheduled by the phy_interrupt/timer to handle PHY changes */ -static void phy_change(void *data) -{ - int err; - struct phy_device *phydev = data; - - err = phy_disable_interrupts(phydev); - - if (err) - goto phy_err; - - spin_lock(&phydev->lock); - if ((PHY_RUNNING == phydev->state) || (PHY_NOLINK == phydev->state)) - phydev->state = PHY_CHANGELINK; - spin_unlock(&phydev->lock); - - enable_irq(phydev->irq); - - /* Reenable interrupts */ - err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); - - if (err) - goto irq_enable_err; - - return; - -irq_enable_err: - disable_irq(phydev->irq); -phy_err: - phy_error(phydev); -} - -/* Bring down the PHY link, and stop checking the status. */ -void phy_stop(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - - if (PHY_HALTED == phydev->state) - goto out_unlock; - - if (phydev->irq != PHY_POLL) { - /* Clear any pending interrupts */ - phy_clear_interrupt(phydev); - - /* Disable PHY Interrupts */ - phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); - } - - phydev->state = PHY_HALTED; - -out_unlock: - spin_unlock(&phydev->lock); -} - - -/* phy_start - * - * description: Indicates the attached device's readiness to - * handle PHY-related work. Used during startup to start the - * PHY, and after a call to phy_stop() to resume operation. - * Also used to indicate the MDIO bus has cleared an error - * condition. - */ -void phy_start(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - - switch (phydev->state) { - case PHY_STARTING: - phydev->state = PHY_PENDING; - break; - case PHY_READY: - phydev->state = PHY_UP; - break; - case PHY_HALTED: - phydev->state = PHY_RESUMING; - default: - break; - } - spin_unlock(&phydev->lock); -} -EXPORT_SYMBOL(phy_stop); -EXPORT_SYMBOL(phy_start); - -#endif /* CONFIG_PHYCONTROL */ /* PHY timer which handles the state machine */ static void phy_timer(unsigned long data) diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index c111383..c44d54f 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -124,133 +124,6 @@ void phy_prepare_link(struct phy_device *phydev, phydev->adjust_link = handler; } -#ifdef CONFIG_PHYCONTROL -/* phy_connect: - * - * description: Convenience function for connecting ethernet - * devices to PHY devices. The default behavior is for - * the PHY infrastructure to handle everything, and only notify - * the connected driver when the link status changes. If you - * don't want, or can't use the provided functionality, you may - * choose to call only the subset of functions which provide - * the desired functionality. - */ -struct phy_device * phy_connect(struct net_device *dev, const char *phy_id, - void (*handler)(struct net_device *), u32 flags) -{ - struct phy_device *phydev; - - phydev = phy_attach(dev, phy_id, flags); - - if (IS_ERR(phydev)) - return phydev; - - phy_prepare_link(phydev, handler); - - phy_start_machine(phydev, NULL); - - if (phydev->irq > 0) - phy_start_interrupts(phydev); - - return phydev; -} -EXPORT_SYMBOL(phy_connect); - -void phy_disconnect(struct phy_device *phydev) -{ - if (phydev->irq > 0) - phy_stop_interrupts(phydev); - - phy_stop_machine(phydev); - - phydev->adjust_link = NULL; - - phy_detach(phydev); -} -EXPORT_SYMBOL(phy_disconnect); - -#endif /* CONFIG_PHYCONTROL */ - -/* phy_attach: - * - * description: Called by drivers to attach to a particular PHY - * device. The phy_device is found, and properly hooked up - * to the phy_driver. If no driver is attached, then the - * genphy_driver is used. The phy_device is given a ptr to - * the attaching device, and given a callback for link status - * change. The phy_device is returned to the attaching - * driver. - */ -static int phy_compare_id(struct device *dev, void *data) -{ - return strcmp((char *)data, dev->bus_id) ? 0 : 1; -} - -struct phy_device *phy_attach(struct net_device *dev, - const char *phy_id, u32 flags) -{ - struct bus_type *bus = &mdio_bus_type; - struct phy_device *phydev; - struct device *d; - - /* Search the list of PHY devices on the mdio bus for the - * PHY with the requested name */ - d = bus_find_device(bus, NULL, (void *)phy_id, phy_compare_id); - - if (d) { - phydev = to_phy_device(d); - } else { - printk(KERN_ERR "%s not found\n", phy_id); - return ERR_PTR(-ENODEV); - } - - /* Assume that if there is no driver, that it doesn't - * exist, and we should use the genphy driver. */ - if (NULL == d->driver) { - int err; - down_write(&d->bus->subsys.rwsem); - d->driver = &genphy_driver.driver; - - err = d->driver->probe(d); - - if (err < 0) - return ERR_PTR(err); - - device_bind_driver(d); - up_write(&d->bus->subsys.rwsem); - } - - if (phydev->attached_dev) { - printk(KERN_ERR "%s: %s already attached\n", - dev->name, phy_id); - return ERR_PTR(-EBUSY); - } - - phydev->attached_dev = dev; - - phydev->dev_flags = flags; - - return phydev; -} -EXPORT_SYMBOL(phy_attach); - -void phy_detach(struct phy_device *phydev) -{ - phydev->attached_dev = NULL; - - /* If the device had no specific driver before (i.e. - it - * was using the generic driver), we unbind the device - * from the generic driver so that there's a chance a - * real driver could be loaded */ - if (phydev->dev.driver == &genphy_driver.driver) { - down_write(&phydev->dev.bus->subsys.rwsem); - device_release_driver(&phydev->dev); - up_write(&phydev->dev.bus->subsys.rwsem); - } -} -EXPORT_SYMBOL(phy_detach); - - /* Generic PHY support and helper functions */ /* genphy_config_advert @@ -259,7 +132,7 @@ EXPORT_SYMBOL(phy_detach); * after sanitizing the values to make sure we only advertise * what is supported */ -int genphy_config_advert(struct phy_device *phydev) +static int genphy_config_advert(struct phy_device *phydev) { u32 advertise; int adv; @@ -317,7 +190,6 @@ int genphy_config_advert(struct phy_device *phydev) return adv; } -EXPORT_SYMBOL(genphy_config_advert); /* genphy_setup_forced * diff --git a/include/linux/phy.h b/include/linux/phy.h index 72cb67b..4f2b5ef 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -334,26 +334,11 @@ int phy_write(struct phy_device *phydev, u16 regnum, u16 val); struct phy_device* get_phy_device(struct mii_bus *bus, int addr); int phy_clear_interrupt(struct phy_device *phydev); int phy_config_interrupt(struct phy_device *phydev, u32 interrupts); -struct phy_device * phy_attach(struct net_device *dev, - const char *phy_id, u32 flags); -struct phy_device * phy_connect(struct net_device *dev, const char *phy_id, - void (*handler)(struct net_device *), u32 flags); -void phy_disconnect(struct phy_device *phydev); -void phy_detach(struct phy_device *phydev); -void phy_start(struct phy_device *phydev); -void phy_stop(struct phy_device *phydev); -int phy_start_aneg(struct phy_device *phydev); - -int mdiobus_register(struct mii_bus *bus); -void mdiobus_unregister(struct mii_bus *bus); -void phy_sanitize_settings(struct phy_device *phydev); -int phy_stop_interrupts(struct phy_device *phydev); static inline int phy_read_status(struct phy_device *phydev) { return phydev->drv->read_status(phydev); } -int genphy_config_advert(struct phy_device *phydev); int genphy_setup_forced(struct phy_device *phydev); int genphy_restart_aneg(struct phy_device *phydev); int genphy_config_aneg(struct phy_device *phydev); @@ -370,8 +355,6 @@ int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd); int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd); int phy_mii_ioctl(struct phy_device *phydev, struct mii_ioctl_data *mii_data, int cmd); -int phy_start_interrupts(struct phy_device *phydev); -void phy_print_status(struct phy_device *phydev); extern struct bus_type mdio_bus_type; #endif /* __PHY_H */ -- cgit v0.10.2 From 9c15d24f2420c2155eccd32d7ab909a9c0e63c2b Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:58:02 -0700 Subject: [PATCH] ixgb: Set RXDCTL:PTHRESH/HTHRESH to zero Set RXDCTL:PTHRESH/HTHRESH to zero Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c index 097b90c..492783b 100644 --- a/drivers/net/ixgb/ixgb_main.c +++ b/drivers/net/ixgb/ixgb_main.c @@ -145,10 +145,12 @@ MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); /* some defines for controlling descriptor fetches in h/w */ -#define RXDCTL_PTHRESH_DEFAULT 128 /* chip considers prefech below this */ -#define RXDCTL_HTHRESH_DEFAULT 16 /* chip will only prefetch if tail is - pushed this many descriptors from head */ #define RXDCTL_WTHRESH_DEFAULT 16 /* chip writes back at this many or RXT0 */ +#define RXDCTL_PTHRESH_DEFAULT 0 /* chip considers prefech below + * this */ +#define RXDCTL_HTHRESH_DEFAULT 0 /* chip will only prefetch if tail + * is pushed this many descriptors + * from head */ /** * ixgb_init_module - Driver Registration Routine -- cgit v0.10.2 From 51b54b512cd26c4477ccd57b8d3736b99ccef7a0 Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:58:23 -0700 Subject: [PATCH] ixgb: Fix unnecessary link state messages Fix unnecessary link state messages Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c index 3fa1138..94bc3d4 100644 --- a/drivers/net/ixgb/ixgb_ethtool.c +++ b/drivers/net/ixgb/ixgb_ethtool.c @@ -130,6 +130,12 @@ ixgb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) ixgb_down(adapter, TRUE); ixgb_reset(adapter); ixgb_up(adapter); + /* be optimistic about our link, since we were up before */ + adapter->link_speed = 10000; + adapter->link_duplex = FULL_DUPLEX; + netif_carrier_on(netdev); + netif_wake_queue(netdev); + } else ixgb_reset(adapter); @@ -177,6 +183,11 @@ ixgb_set_pauseparam(struct net_device *netdev, if(netif_running(adapter->netdev)) { ixgb_down(adapter, TRUE); ixgb_up(adapter); + /* be optimistic about our link, since we were up before */ + adapter->link_speed = 10000; + adapter->link_duplex = FULL_DUPLEX; + netif_carrier_on(netdev); + netif_wake_queue(netdev); } else ixgb_reset(adapter); @@ -199,6 +210,11 @@ ixgb_set_rx_csum(struct net_device *netdev, uint32_t data) if(netif_running(netdev)) { ixgb_down(adapter,TRUE); ixgb_up(adapter); + /* be optimistic about our link, since we were up before */ + adapter->link_speed = 10000; + adapter->link_duplex = FULL_DUPLEX; + netif_carrier_on(netdev); + netif_wake_queue(netdev); } else ixgb_reset(adapter); return 0; @@ -573,6 +589,11 @@ ixgb_set_ringparam(struct net_device *netdev, adapter->tx_ring = tx_new; if((err = ixgb_up(adapter))) return err; + /* be optimistic about our link, since we were up before */ + adapter->link_speed = 10000; + adapter->link_duplex = FULL_DUPLEX; + netif_carrier_on(netdev); + netif_wake_queue(netdev); } return 0; -- cgit v0.10.2 From 8908c6cd1d6889850148aeb50bb14301959adaa7 Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:58:40 -0700 Subject: [PATCH] ixgb: Use netdev_priv() instead of netdev->priv Use netdev_priv() instead of netdev->priv Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c index 94bc3d4..c80fa000 100644 --- a/drivers/net/ixgb/ixgb_ethtool.c +++ b/drivers/net/ixgb/ixgb_ethtool.c @@ -98,7 +98,7 @@ static struct ixgb_stats ixgb_gstrings_stats[] = { static int ixgb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE); ecmd->advertising = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE); @@ -120,7 +120,7 @@ ixgb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) static int ixgb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); if(ecmd->autoneg == AUTONEG_ENABLE || ecmd->speed + ecmd->duplex != SPEED_10000 + DUPLEX_FULL) @@ -146,7 +146,7 @@ static void ixgb_get_pauseparam(struct net_device *netdev, struct ethtool_pauseparam *pause) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_hw *hw = &adapter->hw; pause->autoneg = AUTONEG_DISABLE; @@ -165,7 +165,7 @@ static int ixgb_set_pauseparam(struct net_device *netdev, struct ethtool_pauseparam *pause) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_hw *hw = &adapter->hw; if(pause->autoneg == AUTONEG_ENABLE) @@ -197,14 +197,16 @@ ixgb_set_pauseparam(struct net_device *netdev, static uint32_t ixgb_get_rx_csum(struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); + return adapter->rx_csum; } static int ixgb_set_rx_csum(struct net_device *netdev, uint32_t data) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); + adapter->rx_csum = data; if(netif_running(netdev)) { @@ -262,7 +264,7 @@ static void ixgb_get_regs(struct net_device *netdev, struct ethtool_regs *regs, void *p) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_hw *hw = &adapter->hw; uint32_t *reg = p; uint32_t *reg_start = reg; @@ -407,7 +409,7 @@ static int ixgb_get_eeprom(struct net_device *netdev, struct ethtool_eeprom *eeprom, uint8_t *bytes) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_hw *hw = &adapter->hw; uint16_t *eeprom_buff; int i, max_len, first_word, last_word; @@ -455,7 +457,7 @@ static int ixgb_set_eeprom(struct net_device *netdev, struct ethtool_eeprom *eeprom, uint8_t *bytes) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_hw *hw = &adapter->hw; uint16_t *eeprom_buff; void *ptr; @@ -513,7 +515,7 @@ static void ixgb_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *drvinfo) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); strncpy(drvinfo->driver, ixgb_driver_name, 32); strncpy(drvinfo->version, ixgb_driver_version, 32); @@ -528,7 +530,7 @@ static void ixgb_get_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_desc_ring *txdr = &adapter->tx_ring; struct ixgb_desc_ring *rxdr = &adapter->rx_ring; @@ -546,7 +548,7 @@ static int ixgb_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_desc_ring *txdr = &adapter->tx_ring; struct ixgb_desc_ring *rxdr = &adapter->rx_ring; struct ixgb_desc_ring tx_old, tx_new, rx_old, rx_new; @@ -628,7 +630,7 @@ ixgb_led_blink_callback(unsigned long data) static int ixgb_phys_id(struct net_device *netdev, uint32_t data) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); if(!data || data > (uint32_t)(MAX_SCHEDULE_TIMEOUT / HZ)) data = (uint32_t)(MAX_SCHEDULE_TIMEOUT / HZ); @@ -664,7 +666,7 @@ static void ixgb_get_ethtool_stats(struct net_device *netdev, struct ethtool_stats *stats, uint64_t *data) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); int i; ixgb_update_stats(adapter); diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c index 492783b..d1fc431 100644 --- a/drivers/net/ixgb/ixgb_main.c +++ b/drivers/net/ixgb/ixgb_main.c @@ -378,7 +378,7 @@ ixgb_probe(struct pci_dev *pdev, SET_NETDEV_DEV(netdev, &pdev->dev); pci_set_drvdata(pdev, netdev); - adapter = netdev->priv; + adapter = netdev_priv(netdev); adapter->netdev = netdev; adapter->pdev = pdev; adapter->hw.back = adapter; @@ -514,7 +514,7 @@ static void __devexit ixgb_remove(struct pci_dev *pdev) { struct net_device *netdev = pci_get_drvdata(pdev); - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); unregister_netdev(netdev); @@ -585,7 +585,7 @@ ixgb_sw_init(struct ixgb_adapter *adapter) static int ixgb_open(struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); int err; /* allocate transmit descriptors */ @@ -628,7 +628,7 @@ err_setup_tx: static int ixgb_close(struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); ixgb_down(adapter, TRUE); @@ -1019,7 +1019,7 @@ ixgb_clean_rx_ring(struct ixgb_adapter *adapter) static int ixgb_set_mac(struct net_device *netdev, void *p) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct sockaddr *addr = p; if(!is_valid_ether_addr(addr->sa_data)) @@ -1045,7 +1045,7 @@ ixgb_set_mac(struct net_device *netdev, void *p) static void ixgb_set_multi(struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_hw *hw = &adapter->hw; struct dev_mc_list *mc_ptr; uint32_t rctl; @@ -1373,7 +1373,7 @@ ixgb_tx_queue(struct ixgb_adapter *adapter, int count, int vlan_id,int tx_flags) static int ixgb_xmit_frame(struct sk_buff *skb, struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); unsigned int first; unsigned int tx_flags = 0; unsigned long flags; @@ -1427,7 +1427,7 @@ ixgb_xmit_frame(struct sk_buff *skb, struct net_device *netdev) static void ixgb_tx_timeout(struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); /* Do the reset outside of interrupt context */ schedule_work(&adapter->tx_timeout_task); @@ -1436,7 +1436,7 @@ ixgb_tx_timeout(struct net_device *netdev) static void ixgb_tx_timeout_task(struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); ixgb_down(adapter, TRUE); ixgb_up(adapter); @@ -1453,7 +1453,7 @@ ixgb_tx_timeout_task(struct net_device *netdev) static struct net_device_stats * ixgb_get_stats(struct net_device *netdev) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); return &adapter->net_stats; } @@ -1469,7 +1469,7 @@ ixgb_get_stats(struct net_device *netdev) static int ixgb_change_mtu(struct net_device *netdev, int new_mtu) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); int max_frame = new_mtu + ENET_HEADER_SIZE + ENET_FCS_LENGTH; int old_max_frame = netdev->mtu + ENET_HEADER_SIZE + ENET_FCS_LENGTH; @@ -1643,7 +1643,7 @@ static irqreturn_t ixgb_intr(int irq, void *data, struct pt_regs *regs) { struct net_device *netdev = data; - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); struct ixgb_hw *hw = &adapter->hw; uint32_t icr = IXGB_READ_REG(hw, ICR); #ifndef CONFIG_IXGB_NAPI @@ -1690,7 +1690,7 @@ ixgb_intr(int irq, void *data, struct pt_regs *regs) static int ixgb_clean(struct net_device *netdev, int *budget) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); int work_to_do = min(*budget, netdev->quota); int tx_cleaned; int work_done = 0; @@ -2019,7 +2019,7 @@ ixgb_alloc_rx_buffers(struct ixgb_adapter *adapter) static void ixgb_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); uint32_t ctrl, rctl; ixgb_irq_disable(adapter); @@ -2057,7 +2057,7 @@ ixgb_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp) static void ixgb_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); uint32_t vfta, index; /* add VID to filter table */ @@ -2071,7 +2071,7 @@ ixgb_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid) static void ixgb_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid) { - struct ixgb_adapter *adapter = netdev->priv; + struct ixgb_adapter *adapter = netdev_priv(netdev); uint32_t vfta, index; ixgb_irq_disable(adapter); -- cgit v0.10.2 From 7b89178d1d803c854dfd6f4e81633109a1238884 Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:58:55 -0700 Subject: [PATCH] ixgb: Fix Broadcast/Multicast packets received statistics Fix Broadcast/Multicast packets received statistics Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c index d1fc431..d7a0f4e 100644 --- a/drivers/net/ixgb/ixgb_main.c +++ b/drivers/net/ixgb/ixgb_main.c @@ -1524,7 +1524,8 @@ ixgb_update_stats(struct ixgb_adapter *adapter) multi |= ((u64)IXGB_READ_REG(&adapter->hw, MPRCH) << 32); /* fix up multicast stats by removing broadcasts */ - multi -= bcast; + if(multi >= bcast) + multi -= bcast; adapter->stats.mprcl += (multi & 0xFFFFFFFF); adapter->stats.mprch += (multi >> 32); -- cgit v0.10.2 From 9ef2eec39383f8fe2bd7c9fac4dfdd4fdf7173e6 Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:59:07 -0700 Subject: [PATCH] ixgb: Fix data output by ethtool -d Fix data output by ethtool -d Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c index c80fa000..44a07a9 100644 --- a/drivers/net/ixgb/ixgb_ethtool.c +++ b/drivers/net/ixgb/ixgb_ethtool.c @@ -301,7 +301,8 @@ ixgb_get_regs(struct net_device *netdev, *reg++ = IXGB_READ_REG(hw, RAIDC); /* 19 */ *reg++ = IXGB_READ_REG(hw, RXCSUM); /* 20 */ - for (i = 0; i < IXGB_RAR_ENTRIES; i++) { + /* there are 16 RAR entries in hardware, we only use 3 */ + for(i = 0; i < 16; i++) { *reg++ = IXGB_READ_REG_ARRAY(hw, RAL, (i << 1)); /*21,...,51 */ *reg++ = IXGB_READ_REG_ARRAY(hw, RAH, (i << 1)); /*22,...,52 */ } -- cgit v0.10.2 From db0bacaa8313e00bb571e2d1102dc9f567353a24 Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:59:20 -0700 Subject: [PATCH] ixgb: Ethtool cleanup patch from Stephen Hemminger Ethtool cleanup patch from Stephen Hemminger * use ADVERTISED_xxx fields when setting advertised fields Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c index 44a07a9..762e3a0 100644 --- a/drivers/net/ixgb/ixgb_ethtool.c +++ b/drivers/net/ixgb/ixgb_ethtool.c @@ -101,7 +101,7 @@ ixgb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) struct ixgb_adapter *adapter = netdev_priv(netdev); ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE); - ecmd->advertising = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE); + ecmd->advertising = (ADVERTISED_10000baseT_Full | ADVERTISED_FIBRE); ecmd->port = PORT_FIBRE; ecmd->transceiver = XCVR_EXTERNAL; -- cgit v0.10.2 From fcb01756e8e95e8d4e423377bc435e8856194328 Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:59:31 -0700 Subject: [PATCH] ixgb: Remove unused functions Remove unused functions, render some variable static instead of global - based on patch from Adrian Bunk Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_ee.c b/drivers/net/ixgb/ixgb_ee.c index 3aae110..661a46b 100644 --- a/drivers/net/ixgb/ixgb_ee.c +++ b/drivers/net/ixgb/ixgb_ee.c @@ -565,24 +565,6 @@ ixgb_get_ee_mac_addr(struct ixgb_hw *hw, } } -/****************************************************************************** - * return the compatibility flags from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * compatibility flags if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint16_t -ixgb_get_ee_compatibility(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->compatibility)); - - return(0); -} /****************************************************************************** * return the Printed Board Assembly number from EEPROM @@ -602,81 +584,6 @@ ixgb_get_ee_pba_number(struct ixgb_hw *hw) return(0); } -/****************************************************************************** - * return the Initialization Control Word 1 from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * Initialization Control Word 1 if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint16_t -ixgb_get_ee_init_ctrl_reg_1(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->init_ctrl_reg_1)); - - return(0); -} - -/****************************************************************************** - * return the Initialization Control Word 2 from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * Initialization Control Word 2 if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint16_t -ixgb_get_ee_init_ctrl_reg_2(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->init_ctrl_reg_2)); - - return(0); -} - -/****************************************************************************** - * return the Subsystem Id from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * Subsystem Id if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint16_t -ixgb_get_ee_subsystem_id(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->subsystem_id)); - - return(0); -} - -/****************************************************************************** - * return the Sub Vendor Id from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * Sub Vendor Id if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint16_t -ixgb_get_ee_subvendor_id(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->subvendor_id)); - - return(0); -} /****************************************************************************** * return the Device Id from EEPROM @@ -694,81 +601,6 @@ ixgb_get_ee_device_id(struct ixgb_hw *hw) if(ixgb_check_and_get_eeprom_data(hw) == TRUE) return (le16_to_cpu(ee_map->device_id)); - return(0); -} - -/****************************************************************************** - * return the Vendor Id from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * Device Id if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint16_t -ixgb_get_ee_vendor_id(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->vendor_id)); - - return(0); -} - -/****************************************************************************** - * return the Software Defined Pins Register from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * SDP Register if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint16_t -ixgb_get_ee_swdpins_reg(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->swdpins_reg)); - - return(0); + return (0); } -/****************************************************************************** - * return the D3 Power Management Bits from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * D3 Power Management Bits if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint8_t -ixgb_get_ee_d3_power(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->d3_power)); - - return(0); -} - -/****************************************************************************** - * return the D0 Power Management Bits from EEPROM - * - * hw - Struct containing variables accessed by shared code - * - * Returns: - * D0 Power Management Bits if EEPROM contents are valid, 0 otherwise - ******************************************************************************/ -uint8_t -ixgb_get_ee_d0_power(struct ixgb_hw *hw) -{ - struct ixgb_ee_map_type *ee_map = (struct ixgb_ee_map_type *)hw->eeprom; - - if(ixgb_check_and_get_eeprom_data(hw) == TRUE) - return (le16_to_cpu(ee_map->d0_power)); - - return(0); -} diff --git a/drivers/net/ixgb/ixgb_hw.h b/drivers/net/ixgb/ixgb_hw.h index 97898ef..8bcf31e 100644 --- a/drivers/net/ixgb/ixgb_hw.h +++ b/drivers/net/ixgb/ixgb_hw.h @@ -822,17 +822,8 @@ extern void ixgb_clear_vfta(struct ixgb_hw *hw); /* Access functions to eeprom data */ void ixgb_get_ee_mac_addr(struct ixgb_hw *hw, uint8_t *mac_addr); -uint16_t ixgb_get_ee_compatibility(struct ixgb_hw *hw); uint32_t ixgb_get_ee_pba_number(struct ixgb_hw *hw); -uint16_t ixgb_get_ee_init_ctrl_reg_1(struct ixgb_hw *hw); -uint16_t ixgb_get_ee_init_ctrl_reg_2(struct ixgb_hw *hw); -uint16_t ixgb_get_ee_subsystem_id(struct ixgb_hw *hw); -uint16_t ixgb_get_ee_subvendor_id(struct ixgb_hw *hw); uint16_t ixgb_get_ee_device_id(struct ixgb_hw *hw); -uint16_t ixgb_get_ee_vendor_id(struct ixgb_hw *hw); -uint16_t ixgb_get_ee_swdpins_reg(struct ixgb_hw *hw); -uint8_t ixgb_get_ee_d3_power(struct ixgb_hw *hw); -uint8_t ixgb_get_ee_d0_power(struct ixgb_hw *hw); boolean_t ixgb_get_eeprom_data(struct ixgb_hw *hw); uint16_t ixgb_get_eeprom_word(struct ixgb_hw *hw, uint16_t index); -- cgit v0.10.2 From b40a1f06c062d5fb2dc11fcb826d97b28918524f Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:59:44 -0700 Subject: [PATCH] ixgb: Redefined buffer_info-dma to be dma_addr_t instead of uint64 Redefined buffer_info-dma to be dma_addr_t instead of uint64 Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb.h b/drivers/net/ixgb/ixgb.h index f8d3385..c83271b 100644 --- a/drivers/net/ixgb/ixgb.h +++ b/drivers/net/ixgb/ixgb.h @@ -119,7 +119,7 @@ struct ixgb_adapter; * so a DMA handle can be stored along with the buffer */ struct ixgb_buffer { struct sk_buff *skb; - uint64_t dma; + dma_addr_t dma; unsigned long time_stamp; uint16_t length; uint16_t next_to_watch; -- cgit v0.10.2 From ab707da7cf0a1a1d27c6021356cfb3692cf1bd26 Mon Sep 17 00:00:00 2001 From: Malli Chilakala Date: Thu, 11 Aug 2005 13:59:59 -0700 Subject: [PATCH] ixgb: Driver version, white space, comments Driver version, white space, comments & added Module_version Patch from linville Signed-off-by: Mallikarjuna R Chilakala Signed-off-by: Ganesh Venkatesan Signed-off-by: John Ronciak Signed-off-by: Jeff Garzik diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c index 762e3a0..9d026ed 100644 --- a/drivers/net/ixgb/ixgb_ethtool.c +++ b/drivers/net/ixgb/ixgb_ethtool.c @@ -271,7 +271,8 @@ ixgb_get_regs(struct net_device *netdev, uint8_t i; /* the 1 (one) below indicates an attempt at versioning, if the - * interface in ethtool or the driver this 1 should be incremented */ + * interface in ethtool or the driver changes, this 1 should be + * incremented */ regs->version = (1<<24) | hw->revision_id << 16 | hw->device_id; /* General Registers */ diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c index d7a0f4e..5c55537 100644 --- a/drivers/net/ixgb/ixgb_main.c +++ b/drivers/net/ixgb/ixgb_main.c @@ -29,6 +29,11 @@ #include "ixgb.h" /* Change Log + * 1.0.96 04/19/05 + * - Make needlessly global code static -- bunk@stusta.de + * - ethtool cleanup -- shemminger@osdl.org + * - Support for MODULE_VERSION -- linville@tuxdriver.com + * - add skb_header_cloned check to the tso path -- herbert@apana.org.au * 1.0.88 01/05/05 * - include fix to the condition that determines when to quit NAPI - Robert Olsson * - use netif_poll_{disable/enable} to synchronize between NAPI and i/f up/down @@ -47,10 +52,9 @@ char ixgb_driver_string[] = "Intel(R) PRO/10GbE Network Driver"; #else #define DRIVERNAPI "-NAPI" #endif - -#define DRV_VERSION "1.0.95-k2"DRIVERNAPI +#define DRV_VERSION "1.0.100-k2"DRIVERNAPI char ixgb_driver_version[] = DRV_VERSION; -char ixgb_copyright[] = "Copyright (c) 1999-2005 Intel Corporation."; +static char ixgb_copyright[] = "Copyright (c) 1999-2005 Intel Corporation."; /* ixgb_pci_tbl - PCI Device ID Table * -- cgit v0.10.2 From 050ec18a35f3106437da8e9c55e441c076c7b93e Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Tue, 16 Aug 2005 14:00:54 -0700 Subject: [PATCH] skge: stop bogus sensor messages Some versions of the Marvell yukon generate bogus sensor warning interrupts. The driver would flood log with these messages. Handle this situation cleanly by masking away at boot time. Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182 Signed-off-by: Stephen Hemminger drivers/net/skge.c | 24 ++++++++++-------------- drivers/net/skge.h | 8 ++++++-- 2 files changed, 16 insertions(+), 16 deletions(-) Signed-off-by: Jeff Garzik diff --git a/drivers/net/skge.c b/drivers/net/skge.c index f157394..9ff1261 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -2670,18 +2670,6 @@ static void skge_error_irq(struct skge_hw *hw) /* Timestamp (unused) overflow */ if (hwstatus & IS_IRQ_TIST_OV) skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); - - if (hwstatus & IS_IRQ_SENSOR) { - /* no sensors on 32-bit Yukon */ - if (!(skge_read16(hw, B0_CTST) & CS_BUS_SLOT_SZ)) { - printk(KERN_ERR PFX "ignoring bogus sensor interrups\n"); - skge_write32(hw, B0_HWE_IMSK, - IS_ERR_MSK & ~IS_IRQ_SENSOR); - } else - printk(KERN_WARNING PFX "sensor interrupt\n"); - } - - } if (hwstatus & IS_RAM_RD_PAR) { @@ -2712,9 +2700,10 @@ static void skge_error_irq(struct skge_hw *hw) skge_pci_clear(hw); + /* if error still set then just ignore it */ hwstatus = skge_read32(hw, B0_HWE_ISRC); if (hwstatus & IS_IRQ_STAT) { - printk(KERN_WARNING PFX "IRQ status %x: still set ignoring hardware errors\n", + pr_debug("IRQ status %x: still set ignoring hardware errors\n", hwstatus); hw->intr_mask &= ~IS_HW_ERR; } @@ -2948,12 +2937,20 @@ static int skge_reset(struct skge_hw *hw) else hw->ram_size = t8 * 4096; + hw->intr_mask = IS_HW_ERR | IS_EXT_REG; if (hw->chip_id == CHIP_ID_GENESIS) genesis_init(hw); else { /* switch power to VCC (WA for VAUX problem) */ skge_write8(hw, B0_POWER_CTRL, PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON); + /* avoid boards with stuck Hardware error bits */ + if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) && + (skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) { + printk(KERN_WARNING PFX "stuck hardware sensor bit\n"); + hw->intr_mask &= ~IS_HW_ERR; + } + for (i = 0; i < hw->ports; i++) { skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET); skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR); @@ -2994,7 +2991,6 @@ static int skge_reset(struct skge_hw *hw) skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100)); skge_write32(hw, B2_IRQM_CTRL, TIM_START); - hw->intr_mask = IS_HW_ERR | IS_EXT_REG; skge_write32(hw, B0_IMSK, hw->intr_mask); if (hw->chip_id != CHIP_ID_GENESIS) diff --git a/drivers/net/skge.h b/drivers/net/skge.h index b432f1b..636729f 100644 --- a/drivers/net/skge.h +++ b/drivers/net/skge.h @@ -214,8 +214,6 @@ enum { /* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */ enum { - IS_ERR_MSK = 0x00003fff,/* All Error bits */ - IS_IRQ_TIST_OV = 1<<13, /* Time Stamp Timer Overflow (YUKON only) */ IS_IRQ_SENSOR = 1<<12, /* IRQ from Sensor (YUKON only) */ IS_IRQ_MST_ERR = 1<<11, /* IRQ master error detected */ @@ -230,6 +228,12 @@ enum { IS_M2_PAR_ERR = 1<<2, /* MAC 2 Parity Error */ IS_R1_PAR_ERR = 1<<1, /* Queue R1 Parity Error */ IS_R2_PAR_ERR = 1<<0, /* Queue R2 Parity Error */ + + IS_ERR_MSK = IS_IRQ_MST_ERR | IS_IRQ_STAT + | IS_NO_STAT_M1 | IS_NO_STAT_M2 + | IS_RAM_RD_PAR | IS_RAM_WR_PAR + | IS_M1_PAR_ERR | IS_M2_PAR_ERR + | IS_R1_PAR_ERR | IS_R2_PAR_ERR, }; /* B2_TST_CTRL1 8 bit Test Control Register 1 */ -- cgit v0.10.2 From 5e1705ddc83f77da4b29a6d687da14e971912e41 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Tue, 16 Aug 2005 14:00:58 -0700 Subject: [PATCH] skge: fibre vs copper detection cleanup Cleanup the code that handles fibre vs copper detection. Signed-off-by: Stephen Hemminger drivers/net/skge.c | 26 ++++++++++++-------------- drivers/net/skge.h | 11 ++--------- 2 files changed, 14 insertions(+), 23 deletions(-) Signed-off-by: Jeff Garzik diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 9ff1261..3990829 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -189,7 +189,7 @@ static u32 skge_supported_modes(const struct skge_hw *hw) { u32 supported; - if (iscopper(hw)) { + if (hw->copper) { supported = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Half @@ -222,7 +222,7 @@ static int skge_get_settings(struct net_device *dev, ecmd->transceiver = XCVR_INTERNAL; ecmd->supported = skge_supported_modes(hw); - if (iscopper(hw)) { + if (hw->copper) { ecmd->port = PORT_TP; ecmd->phy_address = hw->phy_addr; } else @@ -1599,7 +1599,7 @@ static void yukon_init(struct skge_hw *hw, int port) adv = PHY_AN_CSMA; if (skge->autoneg == AUTONEG_ENABLE) { - if (iscopper(hw)) { + if (hw->copper) { if (skge->advertising & ADVERTISED_1000baseT_Full) ct1000 |= PHY_M_1000C_AFD; if (skge->advertising & ADVERTISED_1000baseT_Half) @@ -1691,7 +1691,7 @@ static void yukon_mac_init(struct skge_hw *hw, int port) /* Set hardware config mode */ reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP | GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE; - reg |= iscopper(hw) ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB; + reg |= hw->copper ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB; /* Clear GMC reset */ skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET); @@ -2865,7 +2865,7 @@ static const char *skge_board_name(const struct skge_hw *hw) static int skge_reset(struct skge_hw *hw) { u16 ctst; - u8 t8, mac_cfg; + u8 t8, mac_cfg, pmd_type, phy_type; int i; ctst = skge_read16(hw, B0_CTST); @@ -2884,18 +2884,19 @@ static int skge_reset(struct skge_hw *hw) ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA)); hw->chip_id = skge_read8(hw, B2_CHIP_ID); - hw->phy_type = skge_read8(hw, B2_E_1) & 0xf; - hw->pmd_type = skge_read8(hw, B2_PMD_TYP); + phy_type = skge_read8(hw, B2_E_1) & 0xf; + pmd_type = skge_read8(hw, B2_PMD_TYP); + hw->copper = (pmd_type == 'T' || pmd_type == '1'); switch (hw->chip_id) { case CHIP_ID_GENESIS: - switch (hw->phy_type) { + switch (phy_type) { case SK_PHY_BCOM: hw->phy_addr = PHY_ADDR_BCOM; break; default: printk(KERN_ERR PFX "%s: unsupported phy type 0x%x\n", - pci_name(hw->pdev), hw->phy_type); + pci_name(hw->pdev), phy_type); return -EOPNOTSUPP; } break; @@ -2903,13 +2904,10 @@ static int skge_reset(struct skge_hw *hw) case CHIP_ID_YUKON: case CHIP_ID_YUKON_LITE: case CHIP_ID_YUKON_LP: - if (hw->phy_type < SK_PHY_MARV_COPPER && hw->pmd_type != 'S') - hw->phy_type = SK_PHY_MARV_COPPER; + if (phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S') + hw->copper = 1; hw->phy_addr = PHY_ADDR_MARV; - if (!iscopper(hw)) - hw->phy_type = SK_PHY_MARV_FIBER; - break; default: diff --git a/drivers/net/skge.h b/drivers/net/skge.h index 636729f..f1680be 100644 --- a/drivers/net/skge.h +++ b/drivers/net/skge.h @@ -2460,24 +2460,17 @@ struct skge_hw { u8 chip_id; u8 chip_rev; - u8 phy_type; - u8 pmd_type; - u16 phy_addr; + u8 copper; u8 ports; u32 ram_size; u32 ram_offset; + u16 phy_addr; struct tasklet_struct ext_tasklet; spinlock_t phy_lock; }; - -static inline int iscopper(const struct skge_hw *hw) -{ - return (hw->pmd_type == 'T'); -} - enum { FLOW_MODE_NONE = 0, /* No Flow-Control */ FLOW_MODE_LOC_SEND = 1, /* Local station sends PAUSE */ -- cgit v0.10.2 From c59230818f7a8969c2f9d3b601745679127a4016 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Tue, 16 Aug 2005 14:01:02 -0700 Subject: [PATCH] skge: increase receive flush threshold default The flush threshold in the MAC chip should be increased. Found while reviewing vendor version of sk98lin driver. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 3990829..38fc66a 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -1780,7 +1780,12 @@ static void yukon_mac_init(struct skge_hw *hw, int port) reg &= ~GMF_RX_F_FL_ON; skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); skge_write16(hw, SK_REG(port, RX_GMF_CTRL_T), reg); - skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF); + /* + * because Pause Packet Truncation in GMAC is not working + * we have to increase the Flush Threshold to 64 bytes + * in order to flush pause packets in Rx FIFO on Yukon-1 + */ + skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1); /* Configure Tx MAC FIFO */ skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); -- cgit v0.10.2 From 54cfb5aa0f4859bd38706eabe0118175780a542f Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Tue, 16 Aug 2005 14:01:05 -0700 Subject: [PATCH] skge: turn on link status LED Turn on the link status LED when link comes up. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 38fc66a..48a43b8 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -42,7 +42,7 @@ #include "skge.h" #define DRV_NAME "skge" -#define DRV_VERSION "0.8" +#define DRV_VERSION "0.9" #define PFX DRV_NAME " " #define DEFAULT_TX_RING_SIZE 128 @@ -876,6 +876,9 @@ static int skge_rx_fill(struct skge_port *skge) static void skge_link_up(struct skge_port *skge) { + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), + LED_BLK_OFF|LED_SYNC_OFF|LED_ON); + netif_carrier_on(skge->netdev); if (skge->tx_avail > MAX_SKB_FRAGS + 1) netif_wake_queue(skge->netdev); @@ -894,6 +897,7 @@ static void skge_link_up(struct skge_port *skge) static void skge_link_down(struct skge_port *skge) { + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF); netif_carrier_off(skge->netdev); netif_stop_queue(skge->netdev); -- cgit v0.10.2 From 1b1b3c9b6d346d441a99e2de0b34f3ba93963ad8 Mon Sep 17 00:00:00 2001 From: Manfred Spraul Date: Sat, 6 Aug 2005 23:47:55 +0200 Subject: [PATCH] forcedeth: Initialize link settings in every nv_open() MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Rüdiger found a bug in nv_open that explains some of the reports with duplex mismatches: nv_open calls nv_update_link_speed for initializing the hardware link speed registers. If current link setting matches the values in np->linkspeed and np->duplex, then the function does nothing. Usually, doing nothing is the right thing, but not in nv_open: During nv_open, the registers must be initialized because the nic was reset. The attached patch fixes that by setting np->linkspeed to an invalid value before calling nv_update_link_speed from nv_open. Signed-Off-By: Manfred Spraul Signed-off-by: Jeff Garzik diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index f165ae9..7d93948 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -93,6 +93,8 @@ * 0.40: 19 Jul 2005: Add support for mac address change. * 0.41: 30 Jul 2005: Write back original MAC in nv_close instead * of nv_remove + * 0.42: 06 Aug 2005: Fix lack of link speed initialization + * in the second (and later) nv_open call * * Known bugs: * We suspect that on some hardware no TX done interrupts are generated. @@ -2178,6 +2180,9 @@ static int nv_open(struct net_device *dev) writel(NVREG_MIISTAT_MASK, base + NvRegMIIStatus); dprintk(KERN_INFO "startup: got 0x%08x.\n", miistat); } + /* set linkspeed to invalid value, thus force nv_update_linkspeed + * to init hw */ + np->linkspeed = 0; ret = nv_update_linkspeed(dev); nv_start_rx(dev); nv_start_tx(dev); -- cgit v0.10.2 From a51d74409d856e472bad753aecf1f2715718c242 Mon Sep 17 00:00:00 2001 From: Nishanth Aravamudan Date: Mon, 27 Jun 2005 09:20:04 -0700 Subject: [PATCH] net/cycx_drv: replace delay_cycx() with msleep_interruptible() Use msleep_interruptible() instead of delay_cycx() to guarantee the task delays as expected. Remove the prototype and definition of delay_cycx(). Signed-off-by: Nishanth Aravamudan Signed-off-by: Jeff Garzik diff --git a/drivers/net/wan/cycx_drv.c b/drivers/net/wan/cycx_drv.c index 6e74af6..9e56fc3 100644 --- a/drivers/net/wan/cycx_drv.c +++ b/drivers/net/wan/cycx_drv.c @@ -56,7 +56,7 @@ #include /* for jiffies, HZ, etc. */ #include /* API definitions */ #include /* CYCX firmware module definitions */ -#include /* udelay */ +#include /* udelay, msleep_interruptible */ #include /* read[wl], write[wl], ioremap, iounmap */ #define MOD_VERSION 0 @@ -74,7 +74,6 @@ static int reset_cyc2x(void __iomem *addr); static int detect_cyc2x(void __iomem *addr); /* Miscellaneous functions */ -static void delay_cycx(int sec); static int get_option_index(long *optlist, long optval); static u16 checksum(u8 *buf, u32 len); @@ -259,7 +258,7 @@ static int memory_exists(void __iomem *addr) if (readw(addr + 0x10) == TEST_PATTERN) return 1; - delay_cycx(1); + msleep_interruptible(1 * 1000); } return 0; @@ -316,7 +315,7 @@ static void cycx_reset_boot(void __iomem *addr, u8 *code, u32 len) /* 80186 was in hold, go */ writeb(0, addr + START_CPU); - delay_cycx(1); + msleep_interruptible(1 * 1000); } /* Load data.bin file through boot (reset) interface. */ @@ -462,13 +461,13 @@ static int load_cyc2x(struct cycx_hw *hw, struct cycx_firmware *cfm, u32 len) cycx_reset_boot(hw->dpmbase, reset_image, img_hdr->reset_size); /* reset is waiting for boot */ writew(GEN_POWER_ON, pt_cycld); - delay_cycx(1); + msleep_interruptible(1 * 1000); for (j = 0 ; j < 3 ; j++) if (!readw(pt_cycld)) goto reset_loaded; else - delay_cycx(1); + msleep_interruptible(1 * 1000); } printk(KERN_ERR "%s: reset not started.\n", modname); @@ -495,7 +494,7 @@ reset_loaded: /* Arthur Ganzert's tip: wait a while after the firmware loading... seg abr 26 17:17:12 EST 1999 - acme */ - delay_cycx(7); + msleep_interruptible(7 * 1000); printk(KERN_INFO "%s: firmware loaded!\n", modname); /* enable interrupts */ @@ -547,20 +546,13 @@ static int get_option_index(long *optlist, long optval) static int reset_cyc2x(void __iomem *addr) { writeb(0, addr + RST_ENABLE); - delay_cycx(2); + msleep_interruptible(2 * 1000); writeb(0, addr + RST_DISABLE); - delay_cycx(2); + msleep_interruptible(2 * 1000); return memory_exists(addr); } -/* Delay */ -static void delay_cycx(int sec) -{ - set_current_state(TASK_INTERRUPTIBLE); - schedule_timeout(sec * HZ); -} - /* Calculate 16-bit CRC using CCITT polynomial. */ static u16 checksum(u8 *buf, u32 len) { -- cgit v0.10.2 From 913168de6284cd27810e9ee7ae029d408a2a0555 Mon Sep 17 00:00:00 2001 From: Francois Romieu Date: Sat, 30 Jul 2005 01:12:11 +0200 Subject: [PATCH] r8169: PCI ID for the Linksys EG1032 The Linksys EG1032 uses Realtek's 8169 chipset. Credit goes to Bob Wilson for the report. Signed-off-by: Francois Romieu Signed-off-by: Jeff Garzik diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index d5afe05..2f9b322 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -186,6 +186,7 @@ const static struct { static struct pci_device_id rtl8169_pci_tbl[] = { { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8169), }, { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4300), }, + { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, 0x1032), }, { PCI_DEVICE(0x16ec, 0x0116), }, {0,}, }; -- cgit v0.10.2 From d9a8a0a3574525bf422fd2f05eec739c0d25814f Mon Sep 17 00:00:00 2001 From: Komuro Date: Sat, 6 Aug 2005 12:01:43 +0900 Subject: [PATCH] network: fix fmvj18x_cs multicast code The multicast code of the fmvj18x_cs driver is broken. I fixed it to work properly. Signed-off-by: komurojun-mbn@nifty.com Signed-off-by: Jeff Garzik diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/pcmcia/fmvj18x_cs.c index 9d8197b..384a736 100644 --- a/drivers/net/pcmcia/fmvj18x_cs.c +++ b/drivers/net/pcmcia/fmvj18x_cs.c @@ -134,7 +134,7 @@ typedef struct local_info_t { u_char mc_filter[8]; } local_info_t; -#define MC_FILTERBREAK 64 +#define MC_FILTERBREAK 8 /*====================================================================*/ /* @@ -1012,7 +1012,7 @@ static void fjn_reset(struct net_device *dev) outb(BANK_1U, ioaddr + CONFIG_1); /* set the multicast table to accept none. */ - for (i = 0; i < 6; i++) + for (i = 0; i < 8; i++) outb(0x00, ioaddr + MAR_ADR + i); /* Switch to bank 2 (runtime mode) */ @@ -1269,6 +1269,16 @@ static void set_rx_mode(struct net_device *dev) u_long flags; int i; + int saved_config_0 = inb(ioaddr + CONFIG_0); + + local_irq_save(flags); + + /* Disable Tx and Rx */ + if (sram_config == 0) + outb(CONFIG0_RST, ioaddr + CONFIG_0); + else + outb(CONFIG0_RST_1, ioaddr + CONFIG_0); + if (dev->flags & IFF_PROMISC) { /* Unconditionally log net taps. */ printk("%s: Promiscuous mode enabled.\n", dev->name); @@ -1290,20 +1300,23 @@ static void set_rx_mode(struct net_device *dev) for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count; i++, mclist = mclist->next) { unsigned int bit = - ether_crc_le(ETH_ALEN, mclist->dmi_addr) & 0x3f; - mc_filter[bit >> 3] |= (1 << bit); + ether_crc_le(ETH_ALEN, mclist->dmi_addr) >> 26; + mc_filter[bit >> 3] |= (1 << (bit & 7)); } + outb(2, ioaddr + RX_MODE); /* Use normal mode. */ } - local_irq_save(flags); if (memcmp(mc_filter, lp->mc_filter, sizeof(mc_filter))) { int saved_bank = inb(ioaddr + CONFIG_1); /* Switch to bank 1 and set the multicast table. */ outb(0xe4, ioaddr + CONFIG_1); for (i = 0; i < 8; i++) - outb(mc_filter[i], ioaddr + 8 + i); + outb(mc_filter[i], ioaddr + MAR_ADR + i); memcpy(lp->mc_filter, mc_filter, sizeof(mc_filter)); outb(saved_bank, ioaddr + CONFIG_1); } + + outb(saved_config_0, ioaddr + CONFIG_0); + local_irq_restore(flags); } -- cgit v0.10.2 From b4ee21f442ba7a8c43e00b32088d437259890cd0 Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Wed, 27 Jul 2005 01:14:44 -0700 Subject: [PATCH] e1000 printk warning fix 2 drivers/net/e1000/e1000_main.c: In function `e1000_clean_tx_irq': drivers/net/e1000/e1000_main.c:2774: warning: size_t format, dma_addr_t arg (arg 8) Cc: Jeff Garzik Signed-off-by: Andrew Morton Signed-off-by: Jeff Garzik diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index b82fd15..9b596e0 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -2767,7 +2767,7 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter) " next_to_use <%x>\n" " next_to_clean <%x>\n" "buffer_info[next_to_clean]\n" - " dma <%zx>\n" + " dma <%llx>\n" " time_stamp <%lx>\n" " next_to_watch <%x>\n" " jiffies <%lx>\n" @@ -2776,7 +2776,7 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter) E1000_READ_REG(&adapter->hw, TDT), tx_ring->next_to_use, i, - tx_ring->buffer_info[i].dma, + (unsigned long long)tx_ring->buffer_info[i].dma, tx_ring->buffer_info[i].time_stamp, eop, jiffies, -- cgit v0.10.2 From 9f7f0098eaadd9200ab52ad0dad523f797d3bf39 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Fri, 19 Aug 2005 03:52:49 -0400 Subject: [netdrvr eepro100] check for skb==NULL before calling rx_align(skb) diff --git a/drivers/net/eepro100.c b/drivers/net/eepro100.c index 1795425..8c62ced 100644 --- a/drivers/net/eepro100.c +++ b/drivers/net/eepro100.c @@ -1263,8 +1263,8 @@ speedo_init_rx_ring(struct net_device *dev) for (i = 0; i < RX_RING_SIZE; i++) { struct sk_buff *skb; skb = dev_alloc_skb(PKT_BUF_SZ + sizeof(struct RxFD)); - /* XXX: do we really want to call this before the NULL check? --hch */ - rx_align(skb); /* Align IP on 16 byte boundary */ + if (skb) + rx_align(skb); /* Align IP on 16 byte boundary */ sp->rx_skbuff[i] = skb; if (skb == NULL) break; /* OK. Just initially short of Rx bufs. */ @@ -1654,8 +1654,8 @@ static inline struct RxFD *speedo_rx_alloc(struct net_device *dev, int entry) struct sk_buff *skb; /* Get a fresh skbuff to replace the consumed one. */ skb = dev_alloc_skb(PKT_BUF_SZ + sizeof(struct RxFD)); - /* XXX: do we really want to call this before the NULL check? --hch */ - rx_align(skb); /* Align IP on 16 byte boundary */ + if (skb) + rx_align(skb); /* Align IP on 16 byte boundary */ sp->rx_skbuff[entry] = skb; if (skb == NULL) { sp->rx_ringp[entry] = NULL; -- cgit v0.10.2 From 84c3ea01d163a24323d827e1d280dc3346905972 Mon Sep 17 00:00:00 2001 From: Jochen Friedrich Date: Fri, 19 Aug 2005 21:05:56 -0400 Subject: [netdrvr] Convert madgemc to new MCA API. Now that all tms380 devices have a valid struct device with dma_mask, remove dmalimit from tmsdev_init(). Kconfig: depend tms380tr and madgemc on MCA. abyss.c, proteon.c, skisa.c, tmspci.c, tms380tr.h: remove dmalimit parameter from tmsdev_init(). tms380tr.c: use device->dma_mask instead of dmalimit. madgemc.c: move to new MCA API using struct device. Signed-off-by: Jochen Friedrich Signed-off-by: Jeff Garzik diff --git a/drivers/net/tokenring/Kconfig b/drivers/net/tokenring/Kconfig index 23d0fa4..7d5c23e 100644 --- a/drivers/net/tokenring/Kconfig +++ b/drivers/net/tokenring/Kconfig @@ -84,7 +84,7 @@ config 3C359 config TMS380TR tristate "Generic TMS380 Token Ring ISA/PCI adapter support" - depends on TR && (PCI || ISA) + depends on TR && (PCI || ISA || MCA) select FW_LOADER ---help--- This driver provides generic support for token ring adapters @@ -158,7 +158,7 @@ config ABYSS config MADGEMC tristate "Madge Smart 16/4 Ringnode MicroChannel" - depends on TR && TMS380TR && MCA_LEGACY + depends on TR && TMS380TR && MCA help This tms380 module supports the Madge Smart 16/4 MC16 and MC32 MicroChannel adapters. diff --git a/drivers/net/tokenring/abyss.c b/drivers/net/tokenring/abyss.c index f1e4ef1..9345e68 100644 --- a/drivers/net/tokenring/abyss.c +++ b/drivers/net/tokenring/abyss.c @@ -139,7 +139,7 @@ static int __devinit abyss_attach(struct pci_dev *pdev, const struct pci_device_ */ dev->base_addr += 0x10; - ret = tmsdev_init(dev, PCI_MAX_ADDRESS, &pdev->dev); + ret = tmsdev_init(dev, &pdev->dev); if (ret) { printk("%s: unable to get memory for dev->priv.\n", dev->name); diff --git a/drivers/net/tokenring/madgemc.c b/drivers/net/tokenring/madgemc.c index 659cbdb..3a25d19 100644 --- a/drivers/net/tokenring/madgemc.c +++ b/drivers/net/tokenring/madgemc.c @@ -20,7 +20,7 @@ static const char version[] = "madgemc.c: v0.91 23/01/2000 by Adam Fritzler\n"; #include -#include +#include #include #include #include @@ -38,9 +38,7 @@ static const char version[] = "madgemc.c: v0.91 23/01/2000 by Adam Fritzler\n"; #define MADGEMC_IO_EXTENT 32 #define MADGEMC_SIF_OFFSET 0x08 -struct madgemc_card { - struct net_device *dev; - +struct card_info { /* * These are read from the BIA ROM. */ @@ -57,16 +55,12 @@ struct madgemc_card { unsigned int arblevel:4; unsigned int ringspeed:2; /* 0 = 4mb, 1 = 16, 2 = Auto/none */ unsigned int cabletype:1; /* 0 = RJ45, 1 = DB9 */ - - struct madgemc_card *next; }; -static struct madgemc_card *madgemc_card_list; - static int madgemc_open(struct net_device *dev); static int madgemc_close(struct net_device *dev); static int madgemc_chipset_init(struct net_device *dev); -static void madgemc_read_rom(struct madgemc_card *card); +static void madgemc_read_rom(struct net_device *dev, struct card_info *card); static unsigned short madgemc_setnselout_pins(struct net_device *dev); static void madgemc_setcabletype(struct net_device *dev, int type); @@ -151,261 +145,237 @@ static void madgemc_sifwritew(struct net_device *dev, unsigned short val, unsign -static int __init madgemc_probe(void) +static int __devinit madgemc_probe(struct device *device) { static int versionprinted; struct net_device *dev; struct net_local *tp; - struct madgemc_card *card; - int i,slot = 0; - __u8 posreg[4]; - - if (!MCA_bus) - return -1; - - while (slot != MCA_NOTFOUND) { - /* - * Currently we only support the MC16/32 (MCA ID 002d) - */ - slot = mca_find_unused_adapter(0x002d, slot); - if (slot == MCA_NOTFOUND) - break; - - /* - * If we get here, we have an adapter. - */ - if (versionprinted++ == 0) - printk("%s", version); - - dev = alloc_trdev(sizeof(struct net_local)); - if (dev == NULL) { - printk("madgemc: unable to allocate dev space\n"); - if (madgemc_card_list) - return 0; - return -1; - } + struct card_info *card; + struct mca_device *mdev = to_mca_device(device); + int ret = 0, i = 0; + + if (versionprinted++ == 0) + printk("%s", version); + + if(mca_device_claimed(mdev)) + return -EBUSY; + mca_device_set_claim(mdev, 1); + + dev = alloc_trdev(sizeof(struct net_local)); + if (!dev) { + printk("madgemc: unable to allocate dev space\n"); + mca_device_set_claim(mdev, 0); + ret = -ENOMEM; + goto getout; + } - SET_MODULE_OWNER(dev); - dev->dma = 0; + SET_MODULE_OWNER(dev); + dev->dma = 0; - /* - * Fetch MCA config registers - */ - for(i=0;i<4;i++) - posreg[i] = mca_read_stored_pos(slot, i+2); - - card = kmalloc(sizeof(struct madgemc_card), GFP_KERNEL); - if (card==NULL) { - printk("madgemc: unable to allocate card struct\n"); - free_netdev(dev); - if (madgemc_card_list) - return 0; - return -1; - } - card->dev = dev; - - /* - * Parse configuration information. This all comes - * directly from the publicly available @002d.ADF. - * Get it from Madge or your local ADF library. - */ - - /* - * Base address - */ - dev->base_addr = 0x0a20 + - ((posreg[2] & MC16_POS2_ADDR2)?0x0400:0) + - ((posreg[0] & MC16_POS0_ADDR1)?0x1000:0) + - ((posreg[3] & MC16_POS3_ADDR3)?0x2000:0); - - /* - * Interrupt line - */ - switch(posreg[0] >> 6) { /* upper two bits */ + card = kmalloc(sizeof(struct card_info), GFP_KERNEL); + if (card==NULL) { + printk("madgemc: unable to allocate card struct\n"); + ret = -ENOMEM; + goto getout1; + } + + /* + * Parse configuration information. This all comes + * directly from the publicly available @002d.ADF. + * Get it from Madge or your local ADF library. + */ + + /* + * Base address + */ + dev->base_addr = 0x0a20 + + ((mdev->pos[2] & MC16_POS2_ADDR2)?0x0400:0) + + ((mdev->pos[0] & MC16_POS0_ADDR1)?0x1000:0) + + ((mdev->pos[3] & MC16_POS3_ADDR3)?0x2000:0); + + /* + * Interrupt line + */ + switch(mdev->pos[0] >> 6) { /* upper two bits */ case 0x1: dev->irq = 3; break; case 0x2: dev->irq = 9; break; /* IRQ 2 = IRQ 9 */ case 0x3: dev->irq = 10; break; default: dev->irq = 0; break; - } + } - if (dev->irq == 0) { - printk("%s: invalid IRQ\n", dev->name); - goto getout1; - } + if (dev->irq == 0) { + printk("%s: invalid IRQ\n", dev->name); + ret = -EBUSY; + goto getout2; + } - if (!request_region(dev->base_addr, MADGEMC_IO_EXTENT, - "madgemc")) { - printk(KERN_INFO "madgemc: unable to setup Smart MC in slot %d because of I/O base conflict at 0x%04lx\n", slot, dev->base_addr); - dev->base_addr += MADGEMC_SIF_OFFSET; - goto getout1; - } + if (!request_region(dev->base_addr, MADGEMC_IO_EXTENT, + "madgemc")) { + printk(KERN_INFO "madgemc: unable to setup Smart MC in slot %d because of I/O base conflict at 0x%04lx\n", mdev->slot, dev->base_addr); dev->base_addr += MADGEMC_SIF_OFFSET; + ret = -EBUSY; + goto getout2; + } + dev->base_addr += MADGEMC_SIF_OFFSET; + + /* + * Arbitration Level + */ + card->arblevel = ((mdev->pos[0] >> 1) & 0x7) + 8; + + /* + * Burst mode and Fairness + */ + card->burstmode = ((mdev->pos[2] >> 6) & 0x3); + card->fairness = ((mdev->pos[2] >> 4) & 0x1); + + /* + * Ring Speed + */ + if ((mdev->pos[1] >> 2)&0x1) + card->ringspeed = 2; /* not selected */ + else if ((mdev->pos[2] >> 5) & 0x1) + card->ringspeed = 1; /* 16Mb */ + else + card->ringspeed = 0; /* 4Mb */ + + /* + * Cable type + */ + if ((mdev->pos[1] >> 6)&0x1) + card->cabletype = 1; /* STP/DB9 */ + else + card->cabletype = 0; /* UTP/RJ-45 */ + + + /* + * ROM Info. This requires us to actually twiddle + * bits on the card, so we must ensure above that + * the base address is free of conflict (request_region above). + */ + madgemc_read_rom(dev, card); - /* - * Arbitration Level - */ - card->arblevel = ((posreg[0] >> 1) & 0x7) + 8; - - /* - * Burst mode and Fairness - */ - card->burstmode = ((posreg[2] >> 6) & 0x3); - card->fairness = ((posreg[2] >> 4) & 0x1); - - /* - * Ring Speed - */ - if ((posreg[1] >> 2)&0x1) - card->ringspeed = 2; /* not selected */ - else if ((posreg[2] >> 5) & 0x1) - card->ringspeed = 1; /* 16Mb */ - else - card->ringspeed = 0; /* 4Mb */ - - /* - * Cable type - */ - if ((posreg[1] >> 6)&0x1) - card->cabletype = 1; /* STP/DB9 */ - else - card->cabletype = 0; /* UTP/RJ-45 */ - - - /* - * ROM Info. This requires us to actually twiddle - * bits on the card, so we must ensure above that - * the base address is free of conflict (request_region above). - */ - madgemc_read_rom(card); - - if (card->manid != 0x4d) { /* something went wrong */ - printk(KERN_INFO "%s: Madge MC ROM read failed (unknown manufacturer ID %02x)\n", dev->name, card->manid); - goto getout; - } + if (card->manid != 0x4d) { /* something went wrong */ + printk(KERN_INFO "%s: Madge MC ROM read failed (unknown manufacturer ID %02x)\n", dev->name, card->manid); + goto getout3; + } - if ((card->cardtype != 0x08) && (card->cardtype != 0x0d)) { - printk(KERN_INFO "%s: Madge MC ROM read failed (unknown card ID %02x)\n", dev->name, card->cardtype); - goto getout; - } + if ((card->cardtype != 0x08) && (card->cardtype != 0x0d)) { + printk(KERN_INFO "%s: Madge MC ROM read failed (unknown card ID %02x)\n", dev->name, card->cardtype); + ret = -EIO; + goto getout3; + } - /* All cards except Rev 0 and 1 MC16's have 256kb of RAM */ - if ((card->cardtype == 0x08) && (card->cardrev <= 0x01)) - card->ramsize = 128; - else - card->ramsize = 256; - - printk("%s: %s Rev %d at 0x%04lx IRQ %d\n", - dev->name, - (card->cardtype == 0x08)?MADGEMC16_CARDNAME: - MADGEMC32_CARDNAME, card->cardrev, - dev->base_addr, dev->irq); - - if (card->cardtype == 0x0d) - printk("%s: Warning: MC32 support is experimental and highly untested\n", dev->name); - - if (card->ringspeed==2) { /* Unknown */ - printk("%s: Warning: Ring speed not set in POS -- Please run the reference disk and set it!\n", dev->name); - card->ringspeed = 1; /* default to 16mb */ - } + /* All cards except Rev 0 and 1 MC16's have 256kb of RAM */ + if ((card->cardtype == 0x08) && (card->cardrev <= 0x01)) + card->ramsize = 128; + else + card->ramsize = 256; + + printk("%s: %s Rev %d at 0x%04lx IRQ %d\n", + dev->name, + (card->cardtype == 0x08)?MADGEMC16_CARDNAME: + MADGEMC32_CARDNAME, card->cardrev, + dev->base_addr, dev->irq); + + if (card->cardtype == 0x0d) + printk("%s: Warning: MC32 support is experimental and highly untested\n", dev->name); + + if (card->ringspeed==2) { /* Unknown */ + printk("%s: Warning: Ring speed not set in POS -- Please run the reference disk and set it!\n", dev->name); + card->ringspeed = 1; /* default to 16mb */ + } - printk("%s: RAM Size: %dKB\n", dev->name, card->ramsize); + printk("%s: RAM Size: %dKB\n", dev->name, card->ramsize); - printk("%s: Ring Speed: %dMb/sec on %s\n", dev->name, - (card->ringspeed)?16:4, - card->cabletype?"STP/DB9":"UTP/RJ-45"); - printk("%s: Arbitration Level: %d\n", dev->name, - card->arblevel); + printk("%s: Ring Speed: %dMb/sec on %s\n", dev->name, + (card->ringspeed)?16:4, + card->cabletype?"STP/DB9":"UTP/RJ-45"); + printk("%s: Arbitration Level: %d\n", dev->name, + card->arblevel); - printk("%s: Burst Mode: ", dev->name); - switch(card->burstmode) { + printk("%s: Burst Mode: ", dev->name); + switch(card->burstmode) { case 0: printk("Cycle steal"); break; case 1: printk("Limited burst"); break; case 2: printk("Delayed release"); break; case 3: printk("Immediate release"); break; - } - printk(" (%s)\n", (card->fairness)?"Unfair":"Fair"); - - - /* - * Enable SIF before we assign the interrupt handler, - * just in case we get spurious interrupts that need - * handling. - */ - outb(0, dev->base_addr + MC_CONTROL_REG0); /* sanity */ - madgemc_setsifsel(dev, 1); - if (request_irq(dev->irq, madgemc_interrupt, SA_SHIRQ, - "madgemc", dev)) - goto getout; - - madgemc_chipset_init(dev); /* enables interrupts! */ - madgemc_setcabletype(dev, card->cabletype); + } + printk(" (%s)\n", (card->fairness)?"Unfair":"Fair"); - /* Setup MCA structures */ - mca_set_adapter_name(slot, (card->cardtype == 0x08)?MADGEMC16_CARDNAME:MADGEMC32_CARDNAME); - mca_set_adapter_procfn(slot, madgemc_mcaproc, dev); - mca_mark_as_used(slot); - printk("%s: Ring Station Address: ", dev->name); - printk("%2.2x", dev->dev_addr[0]); - for (i = 1; i < 6; i++) - printk(":%2.2x", dev->dev_addr[i]); - printk("\n"); - - /* XXX is ISA_MAX_ADDRESS correct here? */ - if (tmsdev_init(dev, ISA_MAX_ADDRESS, NULL)) { - printk("%s: unable to get memory for dev->priv.\n", - dev->name); - release_region(dev->base_addr-MADGEMC_SIF_OFFSET, - MADGEMC_IO_EXTENT); - - kfree(card); - tmsdev_term(dev); - free_netdev(dev); - if (madgemc_card_list) - return 0; - return -1; - } - tp = netdev_priv(dev); - - /* - * The MC16 is physically a 32bit card. However, Madge - * insists on calling it 16bit, so I'll assume here that - * they know what they're talking about. Cut off DMA - * at 16mb. - */ - tp->setnselout = madgemc_setnselout_pins; - tp->sifwriteb = madgemc_sifwriteb; - tp->sifreadb = madgemc_sifreadb; - tp->sifwritew = madgemc_sifwritew; - tp->sifreadw = madgemc_sifreadw; - tp->DataRate = (card->ringspeed)?SPEED_16:SPEED_4; - - memcpy(tp->ProductID, "Madge MCA 16/4 ", PROD_ID_SIZE + 1); - - dev->open = madgemc_open; - dev->stop = madgemc_close; - - if (register_netdev(dev) == 0) { - /* Enlist in the card list */ - card->next = madgemc_card_list; - madgemc_card_list = card; - slot++; - continue; /* successful, try to find another */ - } - - free_irq(dev->irq, dev); - getout: - release_region(dev->base_addr-MADGEMC_SIF_OFFSET, - MADGEMC_IO_EXTENT); - getout1: - kfree(card); - free_netdev(dev); - slot++; + /* + * Enable SIF before we assign the interrupt handler, + * just in case we get spurious interrupts that need + * handling. + */ + outb(0, dev->base_addr + MC_CONTROL_REG0); /* sanity */ + madgemc_setsifsel(dev, 1); + if (request_irq(dev->irq, madgemc_interrupt, SA_SHIRQ, + "madgemc", dev)) { + ret = -EBUSY; + goto getout3; } - if (madgemc_card_list) + madgemc_chipset_init(dev); /* enables interrupts! */ + madgemc_setcabletype(dev, card->cabletype); + + /* Setup MCA structures */ + mca_device_set_name(mdev, (card->cardtype == 0x08)?MADGEMC16_CARDNAME:MADGEMC32_CARDNAME); + mca_set_adapter_procfn(mdev->slot, madgemc_mcaproc, dev); + + printk("%s: Ring Station Address: ", dev->name); + printk("%2.2x", dev->dev_addr[0]); + for (i = 1; i < 6; i++) + printk(":%2.2x", dev->dev_addr[i]); + printk("\n"); + + if (tmsdev_init(dev, device)) { + printk("%s: unable to get memory for dev->priv.\n", + dev->name); + ret = -ENOMEM; + goto getout4; + } + tp = netdev_priv(dev); + + /* + * The MC16 is physically a 32bit card. However, Madge + * insists on calling it 16bit, so I'll assume here that + * they know what they're talking about. Cut off DMA + * at 16mb. + */ + tp->setnselout = madgemc_setnselout_pins; + tp->sifwriteb = madgemc_sifwriteb; + tp->sifreadb = madgemc_sifreadb; + tp->sifwritew = madgemc_sifwritew; + tp->sifreadw = madgemc_sifreadw; + tp->DataRate = (card->ringspeed)?SPEED_16:SPEED_4; + + memcpy(tp->ProductID, "Madge MCA 16/4 ", PROD_ID_SIZE + 1); + + dev->open = madgemc_open; + dev->stop = madgemc_close; + + tp->tmspriv = card; + dev_set_drvdata(device, dev); + + if (register_netdev(dev) == 0) return 0; - return -1; + + dev_set_drvdata(device, NULL); + ret = -ENOMEM; +getout4: + free_irq(dev->irq, dev); +getout3: + release_region(dev->base_addr-MADGEMC_SIF_OFFSET, + MADGEMC_IO_EXTENT); +getout2: + kfree(card); +getout1: + free_netdev(dev); +getout: + mca_device_set_claim(mdev, 0); + return ret; } /* @@ -664,12 +634,12 @@ static void madgemc_chipset_close(struct net_device *dev) * is complete. * */ -static void madgemc_read_rom(struct madgemc_card *card) +static void madgemc_read_rom(struct net_device *dev, struct card_info *card) { unsigned long ioaddr; unsigned char reg0, reg1, tmpreg0, i; - ioaddr = card->dev->base_addr; + ioaddr = dev->base_addr; reg0 = inb(ioaddr + MC_CONTROL_REG0); reg1 = inb(ioaddr + MC_CONTROL_REG1); @@ -686,9 +656,9 @@ static void madgemc_read_rom(struct madgemc_card *card) outb(tmpreg0 | MC_CONTROL_REG0_PAGE, ioaddr + MC_CONTROL_REG0); /* Read BIA */ - card->dev->addr_len = 6; + dev->addr_len = 6; for (i = 0; i < 6; i++) - card->dev->dev_addr[i] = inb(ioaddr + MC_ROM_BIA_START + i); + dev->dev_addr[i] = inb(ioaddr + MC_ROM_BIA_START + i); /* Restore original register values */ outb(reg0, ioaddr + MC_CONTROL_REG0); @@ -721,14 +691,10 @@ static int madgemc_close(struct net_device *dev) static int madgemc_mcaproc(char *buf, int slot, void *d) { struct net_device *dev = (struct net_device *)d; - struct madgemc_card *curcard = madgemc_card_list; + struct net_local *tp = dev->priv; + struct card_info *curcard = tp->tmspriv; int len = 0; - while (curcard) { /* search for card struct */ - if (curcard->dev == dev) - break; - curcard = curcard->next; - } len += sprintf(buf+len, "-------\n"); if (curcard) { struct net_local *tp = netdev_priv(dev); @@ -763,25 +729,56 @@ static int madgemc_mcaproc(char *buf, int slot, void *d) return len; } -static void __exit madgemc_exit(void) +static int __devexit madgemc_remove(struct device *device) { - struct net_device *dev; - struct madgemc_card *this_card; - - while (madgemc_card_list) { - dev = madgemc_card_list->dev; - unregister_netdev(dev); - release_region(dev->base_addr-MADGEMC_SIF_OFFSET, MADGEMC_IO_EXTENT); - free_irq(dev->irq, dev); - tmsdev_term(dev); - free_netdev(dev); - this_card = madgemc_card_list; - madgemc_card_list = this_card->next; - kfree(this_card); - } + struct net_device *dev = dev_get_drvdata(device); + struct net_local *tp; + struct card_info *card; + + if (!dev) + BUG(); + + tp = dev->priv; + card = tp->tmspriv; + kfree(card); + tp->tmspriv = NULL; + + unregister_netdev(dev); + release_region(dev->base_addr-MADGEMC_SIF_OFFSET, MADGEMC_IO_EXTENT); + free_irq(dev->irq, dev); + tmsdev_term(dev); + free_netdev(dev); + dev_set_drvdata(device, NULL); + + return 0; +} + +static short madgemc_adapter_ids[] __initdata = { + 0x002d, + 0x0000 +}; + +static struct mca_driver madgemc_driver = { + .id_table = madgemc_adapter_ids, + .driver = { + .name = "madgemc", + .bus = &mca_bus_type, + .probe = madgemc_probe, + .remove = __devexit_p(madgemc_remove), + }, +}; + +static int __init madgemc_init (void) +{ + return mca_register_driver (&madgemc_driver); +} + +static void __exit madgemc_exit (void) +{ + mca_unregister_driver (&madgemc_driver); } -module_init(madgemc_probe); +module_init(madgemc_init); module_exit(madgemc_exit); MODULE_LICENSE("GPL"); diff --git a/drivers/net/tokenring/proteon.c b/drivers/net/tokenring/proteon.c index 0a95977..eb1423e 100644 --- a/drivers/net/tokenring/proteon.c +++ b/drivers/net/tokenring/proteon.c @@ -145,7 +145,7 @@ static int __init setup_card(struct net_device *dev, struct device *pdev) err = -EIO; pdev->dma_mask = &dma_mask; - if (tmsdev_init(dev, ISA_MAX_ADDRESS, pdev)) + if (tmsdev_init(dev, pdev)) goto out4; dev->base_addr &= ~3; diff --git a/drivers/net/tokenring/skisa.c b/drivers/net/tokenring/skisa.c index 03f0619..3c7c662 100644 --- a/drivers/net/tokenring/skisa.c +++ b/drivers/net/tokenring/skisa.c @@ -162,7 +162,7 @@ static int __init setup_card(struct net_device *dev, struct device *pdev) err = -EIO; pdev->dma_mask = &dma_mask; - if (tmsdev_init(dev, ISA_MAX_ADDRESS, pdev)) + if (tmsdev_init(dev, pdev)) goto out4; dev->base_addr &= ~3; diff --git a/drivers/net/tokenring/tms380tr.c b/drivers/net/tokenring/tms380tr.c index 9a543fe..2e39bf1 100644 --- a/drivers/net/tokenring/tms380tr.c +++ b/drivers/net/tokenring/tms380tr.c @@ -2333,19 +2333,22 @@ void tmsdev_term(struct net_device *dev) DMA_BIDIRECTIONAL); } -int tmsdev_init(struct net_device *dev, unsigned long dmalimit, - struct device *pdev) +int tmsdev_init(struct net_device *dev, struct device *pdev) { struct net_local *tms_local; memset(dev->priv, 0, sizeof(struct net_local)); tms_local = netdev_priv(dev); init_waitqueue_head(&tms_local->wait_for_tok_int); - tms_local->dmalimit = dmalimit; + if (pdev->dma_mask) + tms_local->dmalimit = *pdev->dma_mask; + else + return -ENOMEM; tms_local->pdev = pdev; tms_local->dmabuffer = dma_map_single(pdev, (void *)tms_local, sizeof(struct net_local), DMA_BIDIRECTIONAL); - if (tms_local->dmabuffer + sizeof(struct net_local) > dmalimit) + if (tms_local->dmabuffer + sizeof(struct net_local) > + tms_local->dmalimit) { printk(KERN_INFO "%s: Memory not accessible for DMA\n", dev->name); diff --git a/drivers/net/tokenring/tms380tr.h b/drivers/net/tokenring/tms380tr.h index 077f568..30452c6 100644 --- a/drivers/net/tokenring/tms380tr.h +++ b/drivers/net/tokenring/tms380tr.h @@ -17,8 +17,7 @@ int tms380tr_open(struct net_device *dev); int tms380tr_close(struct net_device *dev); irqreturn_t tms380tr_interrupt(int irq, void *dev_id, struct pt_regs *regs); -int tmsdev_init(struct net_device *dev, unsigned long dmalimit, - struct device *pdev); +int tmsdev_init(struct net_device *dev, struct device *pdev); void tmsdev_term(struct net_device *dev); void tms380tr_wait(unsigned long time); diff --git a/drivers/net/tokenring/tmspci.c b/drivers/net/tokenring/tmspci.c index 0014aef..ab47c05 100644 --- a/drivers/net/tokenring/tmspci.c +++ b/drivers/net/tokenring/tmspci.c @@ -143,7 +143,7 @@ static int __devinit tms_pci_attach(struct pci_dev *pdev, const struct pci_devic printk(":%2.2x", dev->dev_addr[i]); printk("\n"); - ret = tmsdev_init(dev, PCI_MAX_ADDRESS, &pdev->dev); + ret = tmsdev_init(dev, &pdev->dev); if (ret) { printk("%s: unable to get memory for dev->priv.\n", dev->name); goto err_out_irq; -- cgit v0.10.2 From 3d52365c4f62edb9ff9710e1c57952e957b2879f Mon Sep 17 00:00:00 2001 From: Jochen Friedrich Date: Fri, 19 Aug 2005 15:51:46 +0200 Subject: [PATCH] tms380tr: remove prototypes in Space.c Cleanup: remove two prototypes. Signed-off-by: Jochen Friedrich Signed-off-by: Jeff Garzik diff --git a/drivers/net/Space.c b/drivers/net/Space.c index 11c44be..b28e5fd 100644 --- a/drivers/net/Space.c +++ b/drivers/net/Space.c @@ -318,8 +318,6 @@ static void __init ethif_probe2(int unit) #ifdef CONFIG_TR /* Token-ring device probe */ extern int ibmtr_probe_card(struct net_device *); -extern struct net_device *sk_isa_probe(int unit); -extern struct net_device *proteon_probe(int unit); extern struct net_device *smctr_probe(int unit); static struct devprobe2 tr_probes2[] __initdata = { -- cgit v0.10.2 From e960fc5c7d9144b1ce80dda9891ca7dfc656c078 Mon Sep 17 00:00:00 2001 From: "ravinandan.arakali@neterion.com" Date: Fri, 12 Aug 2005 10:15:59 -0700 Subject: [PATCH] S2io: Hardware fixes for Xframe II adapter Hi, Patch Description: This patch incorporates the following hardware fixes required for Xframe II adapter. 1. New values to program the dtx_control register. 2. Disable memory controller interrupts(MC_INTR) since these are now monitored thru' a poll routine. 3. Don't reset an XframeII card on an ECC double-bit error(It can recover). 4. Save/restore PCI config space before/after a reset irrespective of Xframe I or II card. 5. Bumped up the driver version no. to 2.0.3.1 Please review the patch and apply the same if it looks ok. Signed-off-by: Ravinandan Arakali Signed-off-by: Jeff Garzik diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index e083351..7ca7822 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -67,7 +67,7 @@ /* S2io Driver name & version. */ static char s2io_driver_name[] = "Neterion"; -static char s2io_driver_version[] = "Version 2.0.2.1"; +static char s2io_driver_version[] = "Version 2.0.3.1"; static inline int RXD_IS_UP2DT(RxD_t *rxdp) { @@ -210,14 +210,18 @@ static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid) static u64 herc_act_dtx_cfg[] = { /* Set address */ - 0x80000515BA750000ULL, 0x80000515BA7500E0ULL, + 0x8000051536750000ULL, 0x80000515367500E0ULL, /* Write data */ - 0x80000515BA750004ULL, 0x80000515BA7500E4ULL, + 0x8000051536750004ULL, 0x80000515367500E4ULL, /* Set address */ 0x80010515003F0000ULL, 0x80010515003F00E0ULL, /* Write data */ 0x80010515003F0004ULL, 0x80010515003F00E4ULL, /* Set address */ + 0x801205150D440000ULL, 0x801205150D4400E0ULL, + /* Write data */ + 0x801205150D440004ULL, 0x801205150D4400E4ULL, + /* Set address */ 0x80020515F2100000ULL, 0x80020515F21000E0ULL, /* Write data */ 0x80020515F2100004ULL, 0x80020515F21000E4ULL, @@ -1903,7 +1907,7 @@ static int start_nic(struct s2io_nic *nic) } /* Enable select interrupts */ - interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | MC_INTR; + interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR; interruptible |= TX_PIC_INTR | RX_PIC_INTR; interruptible |= TX_MAC_INTR | RX_MAC_INTR; @@ -2030,7 +2034,7 @@ static void stop_nic(struct s2io_nic *nic) config = &nic->config; /* Disable all interrupts */ - interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR | MC_INTR; + interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR; interruptible |= TX_PIC_INTR | RX_PIC_INTR; interruptible |= TX_MAC_INTR | RX_MAC_INTR; en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS); @@ -2688,8 +2692,10 @@ static void alarm_intr_handler(struct s2io_nic *nic) DBG_PRINT(ERR_DBG, "%s: Device indicates ", dev->name); DBG_PRINT(ERR_DBG, "double ECC error!!\n"); - netif_stop_queue(dev); - schedule_work(&nic->rst_timer_task); + if (nic->device_type != XFRAME_II_DEVICE) { + netif_stop_queue(dev); + schedule_work(&nic->rst_timer_task); + } } else { nic->mac_control.stats_info->sw_stat. single_ecc_errs++; @@ -2772,8 +2778,7 @@ void s2io_reset(nic_t * sp) u16 subid, pci_cmd; /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */ - if (sp->device_type == XFRAME_I_DEVICE) - pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd)); + pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd)); val64 = SW_RESET_ALL; writeq(val64, &bar0->sw_reset); @@ -2792,14 +2797,10 @@ void s2io_reset(nic_t * sp) */ msleep(250); - if (!(sp->device_type & XFRAME_II_DEVICE)) { - /* Restore the PCI state saved during initializarion. */ - pci_restore_state(sp->pdev); - pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, + /* Restore the PCI state saved during initialization. */ + pci_restore_state(sp->pdev); + pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, pci_cmd); - } else { - pci_set_master(sp->pdev); - } s2io_init_pci(sp); msleep(250); @@ -5426,9 +5427,7 @@ s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre) INIT_WORK(&sp->set_link_task, (void (*)(void *)) s2io_set_link, sp); - if (!(sp->device_type & XFRAME_II_DEVICE)) { - pci_save_state(sp->pdev); - } + pci_save_state(sp->pdev); /* Setting swapper control on the NIC, for proper reset operation */ if (s2io_set_swapper(sp)) { -- cgit v0.10.2 From 2600636065406dc14948ac2d2913c66c51be80d5 Mon Sep 17 00:00:00 2001 From: Dale Farnsworth Date: Mon, 22 Aug 2005 15:53:29 -0700 Subject: [PATCH] mv643xx: add workaround for HW checksum generation bug [PATCH] [NET] mv643xx: add workaround for HW checksum generation bug The hardware checksum generator on the mv64xxx occasionally generates an incorrect checksum. This patch works around the issue and enables hardware checksum generation. Signed-off-by: Dale Farnsworth Signed-off-by: Jeff Garzik diff --git a/drivers/net/mv643xx_eth.c b/drivers/net/mv643xx_eth.c index 0405e1f..fb6b232 100644 --- a/drivers/net/mv643xx_eth.c +++ b/drivers/net/mv643xx_eth.c @@ -1157,16 +1157,20 @@ static int mv643xx_eth_start_xmit(struct sk_buff *skb, struct net_device *dev) if (!skb_shinfo(skb)->nr_frags) { linear: if (skb->ip_summed != CHECKSUM_HW) { + /* Errata BTS #50, IHL must be 5 if no HW checksum */ pkt_info.cmd_sts = ETH_TX_ENABLE_INTERRUPT | - ETH_TX_FIRST_DESC | ETH_TX_LAST_DESC; + ETH_TX_FIRST_DESC | + ETH_TX_LAST_DESC | + 5 << ETH_TX_IHL_SHIFT; pkt_info.l4i_chk = 0; } else { - u32 ipheader = skb->nh.iph->ihl << 11; pkt_info.cmd_sts = ETH_TX_ENABLE_INTERRUPT | - ETH_TX_FIRST_DESC | ETH_TX_LAST_DESC | - ETH_GEN_TCP_UDP_CHECKSUM | - ETH_GEN_IP_V_4_CHECKSUM | ipheader; + ETH_TX_FIRST_DESC | + ETH_TX_LAST_DESC | + ETH_GEN_TCP_UDP_CHECKSUM | + ETH_GEN_IP_V_4_CHECKSUM | + skb->nh.iph->ihl << ETH_TX_IHL_SHIFT; /* CPU already calculated pseudo header checksum. */ if (skb->nh.iph->protocol == IPPROTO_UDP) { pkt_info.cmd_sts |= ETH_UDP_FRAME; @@ -1193,7 +1197,6 @@ linear: stats->tx_bytes += pkt_info.byte_cnt; } else { unsigned int frag; - u32 ipheader; /* Since hardware can't handle unaligned fragments smaller * than 9 bytes, if we find any, we linearize the skb @@ -1222,12 +1225,16 @@ linear: DMA_TO_DEVICE); pkt_info.l4i_chk = 0; pkt_info.return_info = 0; - pkt_info.cmd_sts = ETH_TX_FIRST_DESC; - if (skb->ip_summed == CHECKSUM_HW) { - ipheader = skb->nh.iph->ihl << 11; - pkt_info.cmd_sts |= ETH_GEN_TCP_UDP_CHECKSUM | - ETH_GEN_IP_V_4_CHECKSUM | ipheader; + if (skb->ip_summed != CHECKSUM_HW) + /* Errata BTS #50, IHL must be 5 if no HW checksum */ + pkt_info.cmd_sts = ETH_TX_FIRST_DESC | + 5 << ETH_TX_IHL_SHIFT; + else { + pkt_info.cmd_sts = ETH_TX_FIRST_DESC | + ETH_GEN_TCP_UDP_CHECKSUM | + ETH_GEN_IP_V_4_CHECKSUM | + skb->nh.iph->ihl << ETH_TX_IHL_SHIFT; /* CPU already calculated pseudo header checksum. */ if (skb->nh.iph->protocol == IPPROTO_UDP) { pkt_info.cmd_sts |= ETH_UDP_FRAME; diff --git a/drivers/net/mv643xx_eth.h b/drivers/net/mv643xx_eth.h index 57c4f8f..7678b59 100644 --- a/drivers/net/mv643xx_eth.h +++ b/drivers/net/mv643xx_eth.h @@ -49,7 +49,7 @@ /* Checksum offload for Tx works for most packets, but * fails if previous packet sent did not use hw csum */ -#undef MV643XX_CHECKSUM_OFFLOAD_TX +#define MV643XX_CHECKSUM_OFFLOAD_TX #define MV643XX_NAPI #define MV643XX_TX_FAST_REFILL #undef MV643XX_RX_QUEUE_FILL_ON_TASK /* Does not work, yet */ @@ -217,6 +217,8 @@ #define ETH_TX_ENABLE_INTERRUPT (BIT23) #define ETH_AUTO_MODE (BIT30) +#define ETH_TX_IHL_SHIFT 11 + /* typedefs */ typedef enum _eth_func_ret_status { -- cgit v0.10.2 From efcce839360fb3a7b6dedeacaec80f68b0f2d052 Mon Sep 17 00:00:00 2001 From: Finn Thain Date: Sat, 20 Aug 2005 15:53:22 +1000 Subject: [PATCH] macsonic/jazzsonic network drivers update The purpose of this patch: - Adopt the DMA API (jazzsonic, macsonic & core driver). - Adopt the driver model (macsonic). This part was cribbed from jazzsonic. As a consequence, macsonic once again works as a module. Driver model is also used by the DMA calls. - Support 16 bit cards (macsonic & core driver, also affects jazzsonic) This code was adapted from the mac68k linux 2.2 kernel, where it has languished for a long time. - Support more 32-bit mac cards (macsonic) Also from mac68k repo. - Zero-copy buffer handling (core driver) Provides a nice performance improvement. The new algorithm incidentally helped to replace the old Jazz DMA code. The patch was tested on a variety of macs (several 32-bit quadra built-in NICs, a 16-bit LC PDS NIC and a 16-bit comm-slot NIC), and also on MIPS Jazz. Signed-off-by: Finn Thain Acked-by: Thomas Bogendoerfer Signed-off-by: Jeff Garzik diff --git a/drivers/net/Space.c b/drivers/net/Space.c index b28e5fd..60304f7 100644 --- a/drivers/net/Space.c +++ b/drivers/net/Space.c @@ -87,7 +87,6 @@ extern struct net_device *mvme147lance_probe(int unit); extern struct net_device *tc515_probe(int unit); extern struct net_device *lance_probe(int unit); extern struct net_device *mace_probe(int unit); -extern struct net_device *macsonic_probe(int unit); extern struct net_device *mac8390_probe(int unit); extern struct net_device *mac89x0_probe(int unit); extern struct net_device *mc32_probe(int unit); @@ -284,9 +283,6 @@ static struct devprobe2 m68k_probes[] __initdata = { #ifdef CONFIG_MACMACE /* Mac 68k Quadra AV builtin Ethernet */ {mace_probe, 0}, #endif -#ifdef CONFIG_MACSONIC /* Mac SONIC-based Ethernet of all sorts */ - {macsonic_probe, 0}, -#endif #ifdef CONFIG_MAC8390 /* NuBus NS8390-based cards */ {mac8390_probe, 0}, #endif diff --git a/drivers/net/jazzsonic.c b/drivers/net/jazzsonic.c index 7fec613..8423cb6 100644 --- a/drivers/net/jazzsonic.c +++ b/drivers/net/jazzsonic.c @@ -1,5 +1,10 @@ /* - * sonic.c + * jazzsonic.c + * + * (C) 2005 Finn Thain + * + * Converted to DMA API, and (from the mac68k project) introduced + * dhd's support for 16-bit cards. * * (C) 1996,1998 by Thomas Bogendoerfer (tsbogend@alpha.franken.de) * @@ -28,8 +33,8 @@ #include #include #include -#include #include +#include #include #include @@ -44,22 +49,20 @@ static struct platform_device *jazz_sonic_device; #define SONIC_MEM_SIZE 0x100 -#define SREGS_PAD(n) u16 n; - #include "sonic.h" /* * Macros to access SONIC registers */ -#define SONIC_READ(reg) (*((volatile unsigned int *)base_addr+reg)) +#define SONIC_READ(reg) (*((volatile unsigned int *)dev->base_addr+reg)) #define SONIC_WRITE(reg,val) \ do { \ - *((volatile unsigned int *)base_addr+(reg)) = (val); \ + *((volatile unsigned int *)dev->base_addr+(reg)) = (val); \ } while (0) -/* use 0 for production, 1 for verification, >2 for debug */ +/* use 0 for production, 1 for verification, >1 for debug */ #ifdef SONIC_DEBUG static unsigned int sonic_debug = SONIC_DEBUG; #else @@ -85,18 +88,18 @@ static unsigned short known_revisions[] = 0xffff /* end of list */ }; -static int __init sonic_probe1(struct net_device *dev, unsigned long base_addr, - unsigned int irq) +static int __init sonic_probe1(struct net_device *dev) { static unsigned version_printed; unsigned int silicon_revision; unsigned int val; - struct sonic_local *lp; + struct sonic_local *lp = netdev_priv(dev); int err = -ENODEV; int i; - if (!request_mem_region(base_addr, SONIC_MEM_SIZE, jazz_sonic_string)) + if (!request_mem_region(dev->base_addr, SONIC_MEM_SIZE, jazz_sonic_string)) return -EBUSY; + /* * get the Silicon Revision ID. If this is one of the known * one assume that we found a SONIC ethernet controller at @@ -120,11 +123,7 @@ static int __init sonic_probe1(struct net_device *dev, unsigned long base_addr, if (sonic_debug && version_printed++ == 0) printk(version); - printk("%s: Sonic ethernet found at 0x%08lx, ", dev->name, base_addr); - - /* Fill in the 'dev' fields. */ - dev->base_addr = base_addr; - dev->irq = irq; + printk(KERN_INFO "%s: Sonic ethernet found at 0x%08lx, ", lp->device->bus_id, dev->base_addr); /* * Put the sonic into software reset, then @@ -138,84 +137,44 @@ static int __init sonic_probe1(struct net_device *dev, unsigned long base_addr, dev->dev_addr[i*2+1] = val >> 8; } - printk("HW Address "); - for (i = 0; i < 6; i++) { - printk("%2.2x", dev->dev_addr[i]); - if (i<5) - printk(":"); - } - - printk(" IRQ %d\n", irq); - err = -ENOMEM; /* Initialize the device structure. */ - if (dev->priv == NULL) { - /* - * the memory be located in the same 64kb segment - */ - lp = NULL; - i = 0; - do { - lp = kmalloc(sizeof(*lp), GFP_KERNEL); - if ((unsigned long) lp >> 16 - != ((unsigned long)lp + sizeof(*lp) ) >> 16) { - /* FIXME, free the memory later */ - kfree(lp); - lp = NULL; - } - } while (lp == NULL && i++ < 20); - - if (lp == NULL) { - printk("%s: couldn't allocate memory for descriptors\n", - dev->name); - goto out; - } - memset(lp, 0, sizeof(struct sonic_local)); - - /* get the virtual dma address */ - lp->cda_laddr = vdma_alloc(CPHYSADDR(lp),sizeof(*lp)); - if (lp->cda_laddr == ~0UL) { - printk("%s: couldn't get DMA page entry for " - "descriptors\n", dev->name); - goto out1; - } - - lp->tda_laddr = lp->cda_laddr + sizeof (lp->cda); - lp->rra_laddr = lp->tda_laddr + sizeof (lp->tda); - lp->rda_laddr = lp->rra_laddr + sizeof (lp->rra); - - /* allocate receive buffer area */ - /* FIXME, maybe we should use skbs */ - lp->rba = kmalloc(SONIC_NUM_RRS * SONIC_RBSIZE, GFP_KERNEL); - if (!lp->rba) { - printk("%s: couldn't allocate receive buffers\n", - dev->name); - goto out2; - } + lp->dma_bitmode = SONIC_BITMODE32; - /* get virtual dma address */ - lp->rba_laddr = vdma_alloc(CPHYSADDR(lp->rba), - SONIC_NUM_RRS * SONIC_RBSIZE); - if (lp->rba_laddr == ~0UL) { - printk("%s: couldn't get DMA page entry for receive " - "buffers\n",dev->name); - goto out3; - } - - /* now convert pointer to KSEG1 pointer */ - lp->rba = (char *)KSEG1ADDR(lp->rba); - flush_cache_all(); - dev->priv = (struct sonic_local *)KSEG1ADDR(lp); + /* Allocate the entire chunk of memory for the descriptors. + Note that this cannot cross a 64K boundary. */ + if ((lp->descriptors = dma_alloc_coherent(lp->device, + SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode), + &lp->descriptors_laddr, GFP_KERNEL)) == NULL) { + printk(KERN_ERR "%s: couldn't alloc DMA memory for descriptors.\n", lp->device->bus_id); + goto out; } - lp = (struct sonic_local *)dev->priv; + /* Now set up the pointers to point to the appropriate places */ + lp->cda = lp->descriptors; + lp->tda = lp->cda + (SIZEOF_SONIC_CDA + * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->rda = lp->tda + (SIZEOF_SONIC_TD * SONIC_NUM_TDS + * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->rra = lp->rda + (SIZEOF_SONIC_RD * SONIC_NUM_RDS + * SONIC_BUS_SCALE(lp->dma_bitmode)); + + lp->cda_laddr = lp->descriptors_laddr; + lp->tda_laddr = lp->cda_laddr + (SIZEOF_SONIC_CDA + * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->rda_laddr = lp->tda_laddr + (SIZEOF_SONIC_TD * SONIC_NUM_TDS + * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->rra_laddr = lp->rda_laddr + (SIZEOF_SONIC_RD * SONIC_NUM_RDS + * SONIC_BUS_SCALE(lp->dma_bitmode)); + dev->open = sonic_open; dev->stop = sonic_close; dev->hard_start_xmit = sonic_send_packet; - dev->get_stats = sonic_get_stats; + dev->get_stats = sonic_get_stats; dev->set_multicast_list = &sonic_multicast_list; + dev->tx_timeout = sonic_tx_timeout; dev->watchdog_timeo = TX_TIMEOUT; /* @@ -226,14 +185,8 @@ static int __init sonic_probe1(struct net_device *dev, unsigned long base_addr, SONIC_WRITE(SONIC_MPT,0xffff); return 0; -out3: - kfree(lp->rba); -out2: - vdma_free(lp->cda_laddr); -out1: - kfree(lp); out: - release_region(base_addr, SONIC_MEM_SIZE); + release_region(dev->base_addr, SONIC_MEM_SIZE); return err; } @@ -245,7 +198,6 @@ static int __init jazz_sonic_probe(struct device *device) { struct net_device *dev; struct sonic_local *lp; - unsigned long base_addr; int err = 0; int i; @@ -255,21 +207,26 @@ static int __init jazz_sonic_probe(struct device *device) if (mips_machgroup != MACH_GROUP_JAZZ) return -ENODEV; - dev = alloc_etherdev(0); + dev = alloc_etherdev(sizeof(struct sonic_local)); if (!dev) return -ENOMEM; + lp = netdev_priv(dev); + lp->device = device; + SET_NETDEV_DEV(dev, device); + SET_MODULE_OWNER(dev); + netdev_boot_setup_check(dev); - base_addr = dev->base_addr; - if (base_addr >= KSEG0) { /* Check a single specified location. */ - err = sonic_probe1(dev, base_addr, dev->irq); - } else if (base_addr != 0) { /* Don't probe at all. */ + if (dev->base_addr >= KSEG0) { /* Check a single specified location. */ + err = sonic_probe1(dev); + } else if (dev->base_addr != 0) { /* Don't probe at all. */ err = -ENXIO; } else { for (i = 0; sonic_portlist[i].port; i++) { - int io = sonic_portlist[i].port; - if (sonic_probe1(dev, io, sonic_portlist[i].irq) == 0) + dev->base_addr = sonic_portlist[i].port; + dev->irq = sonic_portlist[i].irq; + if (sonic_probe1(dev) == 0) break; } if (!sonic_portlist[i].port) @@ -281,14 +238,17 @@ static int __init jazz_sonic_probe(struct device *device) if (err) goto out1; + printk("%s: MAC ", dev->name); + for (i = 0; i < 6; i++) { + printk("%2.2x", dev->dev_addr[i]); + if (i < 5) + printk(":"); + } + printk(" IRQ %d\n", dev->irq); + return 0; out1: - lp = dev->priv; - vdma_free(lp->rba_laddr); - kfree(lp->rba); - vdma_free(lp->cda_laddr); - kfree(lp); release_region(dev->base_addr, SONIC_MEM_SIZE); out: free_netdev(dev); @@ -296,21 +256,22 @@ out: return err; } -/* - * SONIC uses a normal IRQ - */ -#define sonic_request_irq request_irq -#define sonic_free_irq free_irq +MODULE_DESCRIPTION("Jazz SONIC ethernet driver"); +module_param(sonic_debug, int, 0); +MODULE_PARM_DESC(sonic_debug, "jazzsonic debug level (1-4)"); -#define sonic_chiptomem(x) KSEG1ADDR(vdma_log2phys(x)) +#define SONIC_IRQ_FLAG SA_INTERRUPT #include "sonic.c" static int __devexit jazz_sonic_device_remove (struct device *device) { struct net_device *dev = device->driver_data; + struct sonic_local* lp = netdev_priv(dev); unregister_netdev (dev); + dma_free_coherent(lp->device, SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode), + lp->descriptors, lp->descriptors_laddr); release_region (dev->base_addr, SONIC_MEM_SIZE); free_netdev (dev); @@ -323,7 +284,7 @@ static struct device_driver jazz_sonic_driver = { .probe = jazz_sonic_probe, .remove = __devexit_p(jazz_sonic_device_remove), }; - + static void jazz_sonic_platform_release (struct device *device) { struct platform_device *pldev; @@ -336,10 +297,11 @@ static void jazz_sonic_platform_release (struct device *device) static int __init jazz_sonic_init_module(void) { struct platform_device *pldev; + int err; - if (driver_register(&jazz_sonic_driver)) { + if ((err = driver_register(&jazz_sonic_driver))) { printk(KERN_ERR "Driver registration failed\n"); - return -ENOMEM; + return err; } jazz_sonic_device = NULL; diff --git a/drivers/net/macsonic.c b/drivers/net/macsonic.c index be28c65..405e183 100644 --- a/drivers/net/macsonic.c +++ b/drivers/net/macsonic.c @@ -1,6 +1,12 @@ /* * macsonic.c * + * (C) 2005 Finn Thain + * + * Converted to DMA API, converted to unified driver model, made it work as + * a module again, and from the mac68k project, introduced more 32-bit cards + * and dhd's support for 16-bit cards. + * * (C) 1998 Alan Cox * * Debugging Andreas Ehliar, Michael Schmitz @@ -26,8 +32,8 @@ */ #include +#include #include -#include #include #include #include @@ -41,8 +47,8 @@ #include #include #include -#include -#include +#include +#include #include #include @@ -54,25 +60,28 @@ #include #include -#define SREGS_PAD(n) u16 n; +static char mac_sonic_string[] = "macsonic"; +static struct platform_device *mac_sonic_device; #include "sonic.h" -#define SONIC_READ(reg) \ - nubus_readl(base_addr+(reg)) -#define SONIC_WRITE(reg,val) \ - nubus_writel((val), base_addr+(reg)) -#define sonic_read(dev, reg) \ - nubus_readl((dev)->base_addr+(reg)) -#define sonic_write(dev, reg, val) \ - nubus_writel((val), (dev)->base_addr+(reg)) - +/* These should basically be bus-size and endian independent (since + the SONIC is at least smart enough that it uses the same endianness + as the host, unlike certain less enlightened Macintosh NICs) */ +#define SONIC_READ(reg) (nubus_readw(dev->base_addr + (reg * 4) \ + + lp->reg_offset)) +#define SONIC_WRITE(reg,val) (nubus_writew(val, dev->base_addr + (reg * 4) \ + + lp->reg_offset)) + +/* use 0 for production, 1 for verification, >1 for debug */ +#ifdef SONIC_DEBUG +static unsigned int sonic_debug = SONIC_DEBUG; +#else +static unsigned int sonic_debug = 1; +#endif -static int sonic_debug; static int sonic_version_printed; -static int reg_offset; - extern int mac_onboard_sonic_probe(struct net_device* dev); extern int mac_nubus_sonic_probe(struct net_device* dev); @@ -108,40 +117,6 @@ enum macsonic_type { #define SONIC_READ_PROM(addr) nubus_readb(prom_addr+addr) -struct net_device * __init macsonic_probe(int unit) -{ - struct net_device *dev = alloc_etherdev(0); - int err; - - if (!dev) - return ERR_PTR(-ENOMEM); - - if (unit >= 0) - sprintf(dev->name, "eth%d", unit); - - SET_MODULE_OWNER(dev); - - /* This will catch fatal stuff like -ENOMEM as well as success */ - err = mac_onboard_sonic_probe(dev); - if (err == 0) - goto found; - if (err != -ENODEV) - goto out; - err = mac_nubus_sonic_probe(dev); - if (err) - goto out; -found: - err = register_netdev(dev); - if (err) - goto out1; - return dev; -out1: - kfree(dev->priv); -out: - free_netdev(dev); - return ERR_PTR(err); -} - /* * For reversing the PROM address */ @@ -160,103 +135,55 @@ static inline void bit_reverse_addr(unsigned char addr[6]) int __init macsonic_init(struct net_device* dev) { - struct sonic_local* lp = NULL; - int i; + struct sonic_local* lp = netdev_priv(dev); /* Allocate the entire chunk of memory for the descriptors. Note that this cannot cross a 64K boundary. */ - for (i = 0; i < 20; i++) { - unsigned long desc_base, desc_top; - if((lp = kmalloc(sizeof(struct sonic_local), GFP_KERNEL | GFP_DMA)) == NULL) { - printk(KERN_ERR "%s: couldn't allocate descriptor buffers\n", dev->name); - return -ENOMEM; - } - - desc_base = (unsigned long) lp; - desc_top = desc_base + sizeof(struct sonic_local); - if ((desc_top & 0xffff) >= (desc_base & 0xffff)) - break; - /* Hmm. try again (FIXME: does this actually work?) */ - kfree(lp); - printk(KERN_DEBUG - "%s: didn't get continguous chunk [%08lx - %08lx], trying again\n", - dev->name, desc_base, desc_top); - } - - if (lp == NULL) { - printk(KERN_ERR "%s: tried 20 times to allocate descriptor buffers, giving up.\n", - dev->name); + if ((lp->descriptors = dma_alloc_coherent(lp->device, + SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode), + &lp->descriptors_laddr, GFP_KERNEL)) == NULL) { + printk(KERN_ERR "%s: couldn't alloc DMA memory for descriptors.\n", lp->device->bus_id); return -ENOMEM; - } - - dev->priv = lp; - -#if 0 - /* this code is only here as a curiousity... mainly, where the - fuck did SONIC_BUS_SCALE come from, and what was it supposed - to do? the normal allocation works great for 32 bit stuffs.. */ + } /* Now set up the pointers to point to the appropriate places */ - lp->cda = lp->sonic_desc; - lp->tda = lp->cda + (SIZEOF_SONIC_CDA * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->cda = lp->descriptors; + lp->tda = lp->cda + (SIZEOF_SONIC_CDA + * SONIC_BUS_SCALE(lp->dma_bitmode)); lp->rda = lp->tda + (SIZEOF_SONIC_TD * SONIC_NUM_TDS - * SONIC_BUS_SCALE(lp->dma_bitmode)); + * SONIC_BUS_SCALE(lp->dma_bitmode)); lp->rra = lp->rda + (SIZEOF_SONIC_RD * SONIC_NUM_RDS - * SONIC_BUS_SCALE(lp->dma_bitmode)); + * SONIC_BUS_SCALE(lp->dma_bitmode)); -#endif - - memset(lp, 0, sizeof(struct sonic_local)); - - lp->cda_laddr = (unsigned int)&(lp->cda); - lp->tda_laddr = (unsigned int)lp->tda; - lp->rra_laddr = (unsigned int)lp->rra; - lp->rda_laddr = (unsigned int)lp->rda; - - /* FIXME, maybe we should use skbs */ - if ((lp->rba = (char *) - kmalloc(SONIC_NUM_RRS * SONIC_RBSIZE, GFP_KERNEL | GFP_DMA)) == NULL) { - printk(KERN_ERR "%s: couldn't allocate receive buffers\n", dev->name); - dev->priv = NULL; - kfree(lp); - return -ENOMEM; - } - - lp->rba_laddr = (unsigned int)lp->rba; - - { - int rs, ds; - - /* almost always 12*4096, but let's not take chances */ - rs = ((SONIC_NUM_RRS * SONIC_RBSIZE + 4095) / 4096) * 4096; - /* almost always under a page, but let's not take chances */ - ds = ((sizeof(struct sonic_local) + 4095) / 4096) * 4096; - kernel_set_cachemode(lp->rba, rs, IOMAP_NOCACHE_SER); - kernel_set_cachemode(lp, ds, IOMAP_NOCACHE_SER); - } - -#if 0 - flush_cache_all(); -#endif + lp->cda_laddr = lp->descriptors_laddr; + lp->tda_laddr = lp->cda_laddr + (SIZEOF_SONIC_CDA + * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->rda_laddr = lp->tda_laddr + (SIZEOF_SONIC_TD * SONIC_NUM_TDS + * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->rra_laddr = lp->rda_laddr + (SIZEOF_SONIC_RD * SONIC_NUM_RDS + * SONIC_BUS_SCALE(lp->dma_bitmode)); dev->open = sonic_open; dev->stop = sonic_close; dev->hard_start_xmit = sonic_send_packet; dev->get_stats = sonic_get_stats; dev->set_multicast_list = &sonic_multicast_list; + dev->tx_timeout = sonic_tx_timeout; + dev->watchdog_timeo = TX_TIMEOUT; /* * clear tally counter */ - sonic_write(dev, SONIC_CRCT, 0xffff); - sonic_write(dev, SONIC_FAET, 0xffff); - sonic_write(dev, SONIC_MPT, 0xffff); + SONIC_WRITE(SONIC_CRCT, 0xffff); + SONIC_WRITE(SONIC_FAET, 0xffff); + SONIC_WRITE(SONIC_MPT, 0xffff); return 0; } int __init mac_onboard_sonic_ethernet_addr(struct net_device* dev) { + struct sonic_local *lp = netdev_priv(dev); const int prom_addr = ONBOARD_SONIC_PROM_BASE; int i; @@ -270,6 +197,7 @@ int __init mac_onboard_sonic_ethernet_addr(struct net_device* dev) why this is so. */ if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) && memcmp(dev->dev_addr, "\x00\xA0\x40", 3) && + memcmp(dev->dev_addr, "\x00\x80\x19", 3) && memcmp(dev->dev_addr, "\x00\x05\x02", 3)) bit_reverse_addr(dev->dev_addr); else @@ -281,22 +209,23 @@ int __init mac_onboard_sonic_ethernet_addr(struct net_device* dev) the card... */ if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) && memcmp(dev->dev_addr, "\x00\xA0\x40", 3) && + memcmp(dev->dev_addr, "\x00\x80\x19", 3) && memcmp(dev->dev_addr, "\x00\x05\x02", 3)) { unsigned short val; printk(KERN_INFO "macsonic: PROM seems to be wrong, trying CAM entry 15\n"); - sonic_write(dev, SONIC_CMD, SONIC_CR_RST); - sonic_write(dev, SONIC_CEP, 15); + SONIC_WRITE(SONIC_CMD, SONIC_CR_RST); + SONIC_WRITE(SONIC_CEP, 15); - val = sonic_read(dev, SONIC_CAP2); + val = SONIC_READ(SONIC_CAP2); dev->dev_addr[5] = val >> 8; dev->dev_addr[4] = val & 0xff; - val = sonic_read(dev, SONIC_CAP1); + val = SONIC_READ(SONIC_CAP1); dev->dev_addr[3] = val >> 8; dev->dev_addr[2] = val & 0xff; - val = sonic_read(dev, SONIC_CAP0); + val = SONIC_READ(SONIC_CAP0); dev->dev_addr[1] = val >> 8; dev->dev_addr[0] = val & 0xff; @@ -311,6 +240,7 @@ int __init mac_onboard_sonic_ethernet_addr(struct net_device* dev) if (memcmp(dev->dev_addr, "\x08\x00\x07", 3) && memcmp(dev->dev_addr, "\x00\xA0\x40", 3) && + memcmp(dev->dev_addr, "\x00\x80\x19", 3) && memcmp(dev->dev_addr, "\x00\x05\x02", 3)) { /* @@ -325,8 +255,9 @@ int __init mac_onboard_sonic_probe(struct net_device* dev) { /* Bwahahaha */ static int once_is_more_than_enough; - int i; - int dma_bitmode; + struct sonic_local* lp = netdev_priv(dev); + int sr; + int commslot = 0; if (once_is_more_than_enough) return -ENODEV; @@ -335,20 +266,18 @@ int __init mac_onboard_sonic_probe(struct net_device* dev) if (!MACH_IS_MAC) return -ENODEV; - printk(KERN_INFO "Checking for internal Macintosh ethernet (SONIC).. "); - if (macintosh_config->ether_type != MAC_ETHER_SONIC) - { - printk("none.\n"); return -ENODEV; - } - + + printk(KERN_INFO "Checking for internal Macintosh ethernet (SONIC).. "); + /* Bogus probing, on the models which may or may not have Ethernet (BTW, the Ethernet *is* always at the same address, and nothing else lives there, at least if Apple's documentation is to be believed) */ if (macintosh_config->ident == MAC_MODEL_Q630 || macintosh_config->ident == MAC_MODEL_P588 || + macintosh_config->ident == MAC_MODEL_P575 || macintosh_config->ident == MAC_MODEL_C610) { unsigned long flags; int card_present; @@ -361,13 +290,13 @@ int __init mac_onboard_sonic_probe(struct net_device* dev) printk("none.\n"); return -ENODEV; } + commslot = 1; } printk("yes\n"); - /* Danger! My arms are flailing wildly! You *must* set this - before using sonic_read() */ - + /* Danger! My arms are flailing wildly! You *must* set lp->reg_offset + * and dev->base_addr before using SONIC_READ() or SONIC_WRITE() */ dev->base_addr = ONBOARD_SONIC_REGISTERS; if (via_alt_mapping) dev->irq = IRQ_AUTO_3; @@ -379,84 +308,66 @@ int __init mac_onboard_sonic_probe(struct net_device* dev) sonic_version_printed = 1; } printk(KERN_INFO "%s: onboard / comm-slot SONIC at 0x%08lx\n", - dev->name, dev->base_addr); - - /* Now do a song and dance routine in an attempt to determine - the bus width */ + lp->device->bus_id, dev->base_addr); /* The PowerBook's SONIC is 16 bit always. */ if (macintosh_config->ident == MAC_MODEL_PB520) { - reg_offset = 0; - dma_bitmode = 0; - } else if (macintosh_config->ident == MAC_MODEL_C610) { - reg_offset = 0; - dma_bitmode = 1; - } else { + lp->reg_offset = 0; + lp->dma_bitmode = SONIC_BITMODE16; + sr = SONIC_READ(SONIC_SR); + } else if (commslot) { /* Some of the comm-slot cards are 16 bit. But some - of them are not. The 32-bit cards use offset 2 and - pad with zeroes or sometimes ones (I think...) - Therefore, if we try offset 0 and get a silicon - revision of 0, we assume 16 bit. */ - int sr; - - /* Technically this is not necessary since we zeroed - it above */ - reg_offset = 0; - dma_bitmode = 0; - sr = sonic_read(dev, SONIC_SR); - if (sr == 0 || sr == 0xffff) { - reg_offset = 2; - /* 83932 is 0x0004, 83934 is 0x0100 or 0x0101 */ - sr = sonic_read(dev, SONIC_SR); - dma_bitmode = 1; - + of them are not. The 32-bit cards use offset 2 and + have known revisions, we try reading the revision + register at offset 2, if we don't get a known revision + we assume 16 bit at offset 0. */ + lp->reg_offset = 2; + lp->dma_bitmode = SONIC_BITMODE16; + + sr = SONIC_READ(SONIC_SR); + if (sr == 0x0004 || sr == 0x0006 || sr == 0x0100 || sr == 0x0101) + /* 83932 is 0x0004 or 0x0006, 83934 is 0x0100 or 0x0101 */ + lp->dma_bitmode = SONIC_BITMODE32; + else { + lp->dma_bitmode = SONIC_BITMODE16; + lp->reg_offset = 0; + sr = SONIC_READ(SONIC_SR); } - printk(KERN_INFO - "%s: revision 0x%04x, using %d bit DMA and register offset %d\n", - dev->name, sr, dma_bitmode?32:16, reg_offset); + } else { + /* All onboard cards are at offset 2 with 32 bit DMA. */ + lp->reg_offset = 2; + lp->dma_bitmode = SONIC_BITMODE32; + sr = SONIC_READ(SONIC_SR); } - + printk(KERN_INFO + "%s: revision 0x%04x, using %d bit DMA and register offset %d\n", + lp->device->bus_id, sr, lp->dma_bitmode?32:16, lp->reg_offset); - /* this carries my sincere apologies -- by the time I got to updating - the driver, support for "reg_offsets" appeares nowhere in the sonic - code, going back for over a year. Fortunately, my Mac does't seem - to use whatever this was. +#if 0 /* This is sometimes useful to find out how MacOS configured the card. */ + printk(KERN_INFO "%s: DCR: 0x%04x, DCR2: 0x%04x\n", lp->device->bus_id, + SONIC_READ(SONIC_DCR) & 0xffff, SONIC_READ(SONIC_DCR2) & 0xffff); +#endif - If you know how this is supposed to be implemented, either fix it, - or contact me (sammy@oh.verio.com) to explain what it is. --Sam */ - - if(reg_offset) { - printk("%s: register offset unsupported. please fix this if you know what it is.\n", dev->name); - return -ENODEV; - } - /* Software reset, then initialize control registers. */ - sonic_write(dev, SONIC_CMD, SONIC_CR_RST); - sonic_write(dev, SONIC_DCR, SONIC_DCR_BMS | - SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | SONIC_DCR_EXBUS | - (dma_bitmode ? SONIC_DCR_DW : 0)); + SONIC_WRITE(SONIC_CMD, SONIC_CR_RST); + + SONIC_WRITE(SONIC_DCR, SONIC_DCR_EXBUS | SONIC_DCR_BMS | + SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | + (lp->dma_bitmode ? SONIC_DCR_DW : 0)); /* This *must* be written back to in order to restore the - extended programmable output bits */ - sonic_write(dev, SONIC_DCR2, 0); + * extended programmable output bits, as it may not have been + * initialised since the hardware reset. */ + SONIC_WRITE(SONIC_DCR2, 0); /* Clear *and* disable interrupts to be on the safe side */ - sonic_write(dev, SONIC_ISR,0x7fff); - sonic_write(dev, SONIC_IMR,0); + SONIC_WRITE(SONIC_IMR, 0); + SONIC_WRITE(SONIC_ISR, 0x7fff); /* Now look for the MAC address. */ if (mac_onboard_sonic_ethernet_addr(dev) != 0) return -ENODEV; - printk(KERN_INFO "MAC "); - for (i = 0; i < 6; i++) { - printk("%2.2x", dev->dev_addr[i]); - if (i < 5) - printk(":"); - } - - printk(" IRQ %d\n", dev->irq); - /* Shared init code */ return macsonic_init(dev); } @@ -468,8 +379,10 @@ int __init mac_nubus_sonic_ethernet_addr(struct net_device* dev, int i; for(i = 0; i < 6; i++) dev->dev_addr[i] = SONIC_READ_PROM(i); - /* For now we are going to assume that they're all bit-reversed */ - bit_reverse_addr(dev->dev_addr); + + /* Some of the addresses are bit-reversed */ + if (id != MACSONIC_DAYNA) + bit_reverse_addr(dev->dev_addr); return 0; } @@ -487,6 +400,15 @@ int __init macsonic_ident(struct nubus_dev* ndev) else return MACSONIC_APPLE; } + + if (ndev->dr_hw == NUBUS_DRHW_SMC9194 && + ndev->dr_sw == NUBUS_DRSW_DAYNA) + return MACSONIC_DAYNA; + + if (ndev->dr_hw == NUBUS_DRHW_SONIC_LC && + ndev->dr_sw == 0) { /* huh? */ + return MACSONIC_APPLE16; + } return -1; } @@ -494,12 +416,12 @@ int __init mac_nubus_sonic_probe(struct net_device* dev) { static int slots; struct nubus_dev* ndev = NULL; + struct sonic_local* lp = netdev_priv(dev); unsigned long base_addr, prom_addr; u16 sonic_dcr; - int id; - int i; - int dma_bitmode; - + int id = -1; + int reg_offset, dma_bitmode; + /* Find the first SONIC that hasn't been initialized already */ while ((ndev = nubus_find_type(NUBUS_CAT_NETWORK, NUBUS_TYPE_ETHERNET, ndev)) != NULL) @@ -521,51 +443,52 @@ int __init mac_nubus_sonic_probe(struct net_device* dev) case MACSONIC_DUODOCK: base_addr = ndev->board->slot_addr + DUODOCK_SONIC_REGISTERS; prom_addr = ndev->board->slot_addr + DUODOCK_SONIC_PROM_BASE; - sonic_dcr = SONIC_DCR_EXBUS | SONIC_DCR_RFT0 | SONIC_DCR_RFT1 - | SONIC_DCR_TFT0; + sonic_dcr = SONIC_DCR_EXBUS | SONIC_DCR_RFT0 | SONIC_DCR_RFT1 | + SONIC_DCR_TFT0; reg_offset = 2; - dma_bitmode = 1; + dma_bitmode = SONIC_BITMODE32; break; case MACSONIC_APPLE: base_addr = ndev->board->slot_addr + APPLE_SONIC_REGISTERS; prom_addr = ndev->board->slot_addr + APPLE_SONIC_PROM_BASE; sonic_dcr = SONIC_DCR_BMS | SONIC_DCR_RFT1 | SONIC_DCR_TFT0; reg_offset = 0; - dma_bitmode = 1; + dma_bitmode = SONIC_BITMODE32; break; case MACSONIC_APPLE16: base_addr = ndev->board->slot_addr + APPLE_SONIC_REGISTERS; prom_addr = ndev->board->slot_addr + APPLE_SONIC_PROM_BASE; - sonic_dcr = SONIC_DCR_EXBUS - | SONIC_DCR_RFT1 | SONIC_DCR_TFT0 - | SONIC_DCR_PO1 | SONIC_DCR_BMS; + sonic_dcr = SONIC_DCR_EXBUS | SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | + SONIC_DCR_PO1 | SONIC_DCR_BMS; reg_offset = 0; - dma_bitmode = 0; + dma_bitmode = SONIC_BITMODE16; break; case MACSONIC_DAYNALINK: base_addr = ndev->board->slot_addr + APPLE_SONIC_REGISTERS; prom_addr = ndev->board->slot_addr + DAYNALINK_PROM_BASE; - sonic_dcr = SONIC_DCR_RFT1 | SONIC_DCR_TFT0 - | SONIC_DCR_PO1 | SONIC_DCR_BMS; + sonic_dcr = SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | + SONIC_DCR_PO1 | SONIC_DCR_BMS; reg_offset = 0; - dma_bitmode = 0; + dma_bitmode = SONIC_BITMODE16; break; case MACSONIC_DAYNA: base_addr = ndev->board->slot_addr + DAYNA_SONIC_REGISTERS; prom_addr = ndev->board->slot_addr + DAYNA_SONIC_MAC_ADDR; - sonic_dcr = SONIC_DCR_BMS - | SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | SONIC_DCR_PO1; + sonic_dcr = SONIC_DCR_BMS | + SONIC_DCR_RFT1 | SONIC_DCR_TFT0 | SONIC_DCR_PO1; reg_offset = 0; - dma_bitmode = 0; + dma_bitmode = SONIC_BITMODE16; break; default: printk(KERN_ERR "macsonic: WTF, id is %d\n", id); return -ENODEV; } - /* Danger! My arms are flailing wildly! You *must* set this - before using sonic_read() */ + /* Danger! My arms are flailing wildly! You *must* set lp->reg_offset + * and dev->base_addr before using SONIC_READ() or SONIC_WRITE() */ dev->base_addr = base_addr; + lp->reg_offset = reg_offset; + lp->dma_bitmode = dma_bitmode; dev->irq = SLOT2IRQ(ndev->board->slot); if (!sonic_version_printed) { @@ -573,29 +496,66 @@ int __init mac_nubus_sonic_probe(struct net_device* dev) sonic_version_printed = 1; } printk(KERN_INFO "%s: %s in slot %X\n", - dev->name, ndev->board->name, ndev->board->slot); + lp->device->bus_id, ndev->board->name, ndev->board->slot); printk(KERN_INFO "%s: revision 0x%04x, using %d bit DMA and register offset %d\n", - dev->name, sonic_read(dev, SONIC_SR), dma_bitmode?32:16, reg_offset); + lp->device->bus_id, SONIC_READ(SONIC_SR), dma_bitmode?32:16, reg_offset); - if(reg_offset) { - printk("%s: register offset unsupported. please fix this if you know what it is.\n", dev->name); - return -ENODEV; - } +#if 0 /* This is sometimes useful to find out how MacOS configured the card. */ + printk(KERN_INFO "%s: DCR: 0x%04x, DCR2: 0x%04x\n", lp->device->bus_id, + SONIC_READ(SONIC_DCR) & 0xffff, SONIC_READ(SONIC_DCR2) & 0xffff); +#endif /* Software reset, then initialize control registers. */ - sonic_write(dev, SONIC_CMD, SONIC_CR_RST); - sonic_write(dev, SONIC_DCR, sonic_dcr - | (dma_bitmode ? SONIC_DCR_DW : 0)); + SONIC_WRITE(SONIC_CMD, SONIC_CR_RST); + SONIC_WRITE(SONIC_DCR, sonic_dcr | (dma_bitmode ? SONIC_DCR_DW : 0)); + /* This *must* be written back to in order to restore the + * extended programmable output bits, since it may not have been + * initialised since the hardware reset. */ + SONIC_WRITE(SONIC_DCR2, 0); /* Clear *and* disable interrupts to be on the safe side */ - sonic_write(dev, SONIC_ISR,0x7fff); - sonic_write(dev, SONIC_IMR,0); + SONIC_WRITE(SONIC_IMR, 0); + SONIC_WRITE(SONIC_ISR, 0x7fff); /* Now look for the MAC address. */ if (mac_nubus_sonic_ethernet_addr(dev, prom_addr, id) != 0) return -ENODEV; - printk(KERN_INFO "MAC "); + /* Shared init code */ + return macsonic_init(dev); +} + +static int __init mac_sonic_probe(struct device *device) +{ + struct net_device *dev; + struct sonic_local *lp; + int err; + int i; + + dev = alloc_etherdev(sizeof(struct sonic_local)); + if (!dev) + return -ENOMEM; + + lp = netdev_priv(dev); + lp->device = device; + SET_NETDEV_DEV(dev, device); + SET_MODULE_OWNER(dev); + + /* This will catch fatal stuff like -ENOMEM as well as success */ + err = mac_onboard_sonic_probe(dev); + if (err == 0) + goto found; + if (err != -ENODEV) + goto out; + err = mac_nubus_sonic_probe(dev); + if (err) + goto out; +found: + err = register_netdev(dev); + if (err) + goto out; + + printk("%s: MAC ", dev->name); for (i = 0; i < 6; i++) { printk("%2.2x", dev->dev_addr[i]); if (i < 5) @@ -603,55 +563,95 @@ int __init mac_nubus_sonic_probe(struct net_device* dev) } printk(" IRQ %d\n", dev->irq); - /* Shared init code */ - return macsonic_init(dev); -} + return 0; -#ifdef MODULE -static struct net_device *dev_macsonic; +out: + free_netdev(dev); -MODULE_PARM(sonic_debug, "i"); + return err; +} + +MODULE_DESCRIPTION("Macintosh SONIC ethernet driver"); +module_param(sonic_debug, int, 0); MODULE_PARM_DESC(sonic_debug, "macsonic debug level (1-4)"); -int -init_module(void) +#define SONIC_IRQ_FLAG IRQ_FLG_FAST + +#include "sonic.c" + +static int __devexit mac_sonic_device_remove (struct device *device) { - dev_macsonic = macsonic_probe(-1); - if (IS_ERR(dev_macsonic)) { - printk(KERN_WARNING "macsonic.c: No card found\n"); - return PTR_ERR(dev_macsonic); - } + struct net_device *dev = device->driver_data; + struct sonic_local* lp = netdev_priv(dev); + + unregister_netdev (dev); + dma_free_coherent(lp->device, SIZEOF_SONIC_DESC * SONIC_BUS_SCALE(lp->dma_bitmode), + lp->descriptors, lp->descriptors_laddr); + free_netdev (dev); + return 0; } -void -cleanup_module(void) +static struct device_driver mac_sonic_driver = { + .name = mac_sonic_string, + .bus = &platform_bus_type, + .probe = mac_sonic_probe, + .remove = __devexit_p(mac_sonic_device_remove), +}; + +static void mac_sonic_platform_release(struct device *device) { - unregister_netdev(dev_macsonic); - kfree(dev_macsonic->priv); - free_netdev(dev_macsonic); + struct platform_device *pldev; + + /* free device */ + pldev = to_platform_device (device); + kfree (pldev); } -#endif /* MODULE */ +static int __init mac_sonic_init_module(void) +{ + struct platform_device *pldev; + int err; -#define vdma_alloc(foo, bar) ((u32)foo) -#define vdma_free(baz) -#define sonic_chiptomem(bat) (bat) -#define PHYSADDR(quux) (quux) -#define CPHYSADDR(quux) (quux) + if ((err = driver_register(&mac_sonic_driver))) { + printk(KERN_ERR "Driver registration failed\n"); + return err; + } -#define sonic_request_irq request_irq -#define sonic_free_irq free_irq + mac_sonic_device = NULL; -#include "sonic.c" + if (!(pldev = kmalloc (sizeof (*pldev), GFP_KERNEL))) { + goto out_unregister; + } -/* - * Local variables: - * compile-command: "m68k-linux-gcc -D__KERNEL__ -I../../include -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -pipe -fno-strength-reduce -ffixed-a2 -DMODULE -DMODVERSIONS -include ../../include/linux/modversions.h -c -o macsonic.o macsonic.c" - * version-control: t - * kept-new-versions: 5 - * c-indent-level: 8 - * tab-width: 8 - * End: - * - */ + memset(pldev, 0, sizeof (*pldev)); + pldev->name = mac_sonic_string; + pldev->id = 0; + pldev->dev.release = mac_sonic_platform_release; + mac_sonic_device = pldev; + + if (platform_device_register (pldev)) { + kfree(pldev); + mac_sonic_device = NULL; + } + + return 0; + +out_unregister: + platform_device_unregister(pldev); + + return -ENOMEM; +} + +static void __exit mac_sonic_cleanup_module(void) +{ + driver_unregister(&mac_sonic_driver); + + if (mac_sonic_device) { + platform_device_unregister(mac_sonic_device); + mac_sonic_device = NULL; + } +} + +module_init(mac_sonic_init_module); +module_exit(mac_sonic_cleanup_module); diff --git a/drivers/net/sonic.c b/drivers/net/sonic.c index cdc9cc8..90b818a 100644 --- a/drivers/net/sonic.c +++ b/drivers/net/sonic.c @@ -1,6 +1,11 @@ /* * sonic.c * + * (C) 2005 Finn Thain + * + * Converted to DMA API, added zero-copy buffer handling, and + * (from the mac68k project) introduced dhd's support for 16-bit cards. + * * (C) 1996,1998 by Thomas Bogendoerfer (tsbogend@alpha.franken.de) * * This driver is based on work from Andreas Busse, but most of @@ -9,12 +14,23 @@ * (C) 1995 by Andreas Busse (andy@waldorf-gmbh.de) * * Core code included by system sonic drivers + * + * And... partially rewritten again by David Huggins-Daines in order + * to cope with screwed up Macintosh NICs that may or may not use + * 16-bit DMA. + * + * (C) 1999 David Huggins-Daines + * */ /* * Sources: Olivetti M700-10 Risc Personal Computer hardware handbook, * National Semiconductors data sheet for the DP83932B Sonic Ethernet * controller, and the files "8390.c" and "skeleton.c" in this directory. + * + * Additional sources: Nat Semi data sheet for the DP83932C and Nat Semi + * Application Note AN-746, the files "lance.c" and "ibmlana.c". See also + * the NetBSD file "sys/arch/mac68k/dev/if_sn.c". */ @@ -28,6 +44,9 @@ */ static int sonic_open(struct net_device *dev) { + struct sonic_local *lp = netdev_priv(dev); + int i; + if (sonic_debug > 2) printk("sonic_open: initializing sonic driver.\n"); @@ -40,14 +59,59 @@ static int sonic_open(struct net_device *dev) * This means that during execution of the handler interrupt are disabled * covering another bug otherwise corrupting data. This doesn't mean * this glue works ok under all situations. + * + * Note (dhd): this also appears to prevent lockups on the Macintrash + * when more than one Ethernet card is installed (knock on wood) + * + * Note (fthain): whether the above is still true is anyones guess. Certainly + * the buffer handling algorithms will not tolerate re-entrance without some + * mutual exclusion added. Anyway, the memcpy has now been eliminated from the + * rx code to make this a faster "fast interrupt". */ -// if (sonic_request_irq(dev->irq, &sonic_interrupt, 0, "sonic", dev)) { - if (sonic_request_irq(dev->irq, &sonic_interrupt, SA_INTERRUPT, - "sonic", dev)) { - printk("\n%s: unable to get IRQ %d .\n", dev->name, dev->irq); + if (request_irq(dev->irq, &sonic_interrupt, SONIC_IRQ_FLAG, "sonic", dev)) { + printk(KERN_ERR "\n%s: unable to get IRQ %d .\n", dev->name, dev->irq); return -EAGAIN; } + for (i = 0; i < SONIC_NUM_RRS; i++) { + struct sk_buff *skb = dev_alloc_skb(SONIC_RBSIZE + 2); + if (skb == NULL) { + while(i > 0) { /* free any that were allocated successfully */ + i--; + dev_kfree_skb(lp->rx_skb[i]); + lp->rx_skb[i] = NULL; + } + printk(KERN_ERR "%s: couldn't allocate receive buffers\n", + dev->name); + return -ENOMEM; + } + skb->dev = dev; + /* align IP header unless DMA requires otherwise */ + if (SONIC_BUS_SCALE(lp->dma_bitmode) == 2) + skb_reserve(skb, 2); + lp->rx_skb[i] = skb; + } + + for (i = 0; i < SONIC_NUM_RRS; i++) { + dma_addr_t laddr = dma_map_single(lp->device, skb_put(lp->rx_skb[i], SONIC_RBSIZE), + SONIC_RBSIZE, DMA_FROM_DEVICE); + if (!laddr) { + while(i > 0) { /* free any that were mapped successfully */ + i--; + dma_unmap_single(lp->device, lp->rx_laddr[i], SONIC_RBSIZE, DMA_FROM_DEVICE); + lp->rx_laddr[i] = (dma_addr_t)0; + } + for (i = 0; i < SONIC_NUM_RRS; i++) { + dev_kfree_skb(lp->rx_skb[i]); + lp->rx_skb[i] = NULL; + } + printk(KERN_ERR "%s: couldn't map rx DMA buffers\n", + dev->name); + return -ENOMEM; + } + lp->rx_laddr[i] = laddr; + } + /* * Initialize the SONIC */ @@ -67,7 +131,8 @@ static int sonic_open(struct net_device *dev) */ static int sonic_close(struct net_device *dev) { - unsigned int base_addr = dev->base_addr; + struct sonic_local *lp = netdev_priv(dev); + int i; if (sonic_debug > 2) printk("sonic_close\n"); @@ -77,20 +142,56 @@ static int sonic_close(struct net_device *dev) /* * stop the SONIC, disable interrupts */ - SONIC_WRITE(SONIC_ISR, 0x7fff); SONIC_WRITE(SONIC_IMR, 0); + SONIC_WRITE(SONIC_ISR, 0x7fff); SONIC_WRITE(SONIC_CMD, SONIC_CR_RST); - sonic_free_irq(dev->irq, dev); /* release the IRQ */ + /* unmap and free skbs that haven't been transmitted */ + for (i = 0; i < SONIC_NUM_TDS; i++) { + if(lp->tx_laddr[i]) { + dma_unmap_single(lp->device, lp->tx_laddr[i], lp->tx_len[i], DMA_TO_DEVICE); + lp->tx_laddr[i] = (dma_addr_t)0; + } + if(lp->tx_skb[i]) { + dev_kfree_skb(lp->tx_skb[i]); + lp->tx_skb[i] = NULL; + } + } + + /* unmap and free the receive buffers */ + for (i = 0; i < SONIC_NUM_RRS; i++) { + if(lp->rx_laddr[i]) { + dma_unmap_single(lp->device, lp->rx_laddr[i], SONIC_RBSIZE, DMA_FROM_DEVICE); + lp->rx_laddr[i] = (dma_addr_t)0; + } + if(lp->rx_skb[i]) { + dev_kfree_skb(lp->rx_skb[i]); + lp->rx_skb[i] = NULL; + } + } + + free_irq(dev->irq, dev); /* release the IRQ */ return 0; } static void sonic_tx_timeout(struct net_device *dev) { - struct sonic_local *lp = (struct sonic_local *) dev->priv; - printk("%s: transmit timed out.\n", dev->name); - + struct sonic_local *lp = netdev_priv(dev); + int i; + /* Stop the interrupts for this */ + SONIC_WRITE(SONIC_IMR, 0); + /* We could resend the original skbs. Easier to re-initialise. */ + for (i = 0; i < SONIC_NUM_TDS; i++) { + if(lp->tx_laddr[i]) { + dma_unmap_single(lp->device, lp->tx_laddr[i], lp->tx_len[i], DMA_TO_DEVICE); + lp->tx_laddr[i] = (dma_addr_t)0; + } + if(lp->tx_skb[i]) { + dev_kfree_skb(lp->tx_skb[i]); + lp->tx_skb[i] = NULL; + } + } /* Try to restart the adaptor. */ sonic_init(dev); lp->stats.tx_errors++; @@ -100,60 +201,92 @@ static void sonic_tx_timeout(struct net_device *dev) /* * transmit packet + * + * Appends new TD during transmission thus avoiding any TX interrupts + * until we run out of TDs. + * This routine interacts closely with the ISR in that it may, + * set tx_skb[i] + * reset the status flags of the new TD + * set and reset EOL flags + * stop the tx queue + * The ISR interacts with this routine in various ways. It may, + * reset tx_skb[i] + * test the EOL and status flags of the TDs + * wake the tx queue + * Concurrently with all of this, the SONIC is potentially writing to + * the status flags of the TDs. + * Until some mutual exclusion is added, this code will not work with SMP. However, + * MIPS Jazz machines and m68k Macs were all uni-processor machines. */ + static int sonic_send_packet(struct sk_buff *skb, struct net_device *dev) { - struct sonic_local *lp = (struct sonic_local *) dev->priv; - unsigned int base_addr = dev->base_addr; - unsigned int laddr; - int entry, length; - - netif_stop_queue(dev); + struct sonic_local *lp = netdev_priv(dev); + dma_addr_t laddr; + int length; + int entry = lp->next_tx; if (sonic_debug > 2) printk("sonic_send_packet: skb=%p, dev=%p\n", skb, dev); + length = skb->len; + if (length < ETH_ZLEN) { + skb = skb_padto(skb, ETH_ZLEN); + if (skb == NULL) + return 0; + length = ETH_ZLEN; + } + /* * Map the packet data into the logical DMA address space */ - if ((laddr = vdma_alloc(CPHYSADDR(skb->data), skb->len)) == ~0UL) { - printk("%s: no VDMA entry for transmit available.\n", - dev->name); + + laddr = dma_map_single(lp->device, skb->data, length, DMA_TO_DEVICE); + if (!laddr) { + printk(KERN_ERR "%s: failed to map tx DMA buffer.\n", dev->name); dev_kfree_skb(skb); - netif_start_queue(dev); return 1; } - entry = lp->cur_tx & SONIC_TDS_MASK; + + sonic_tda_put(dev, entry, SONIC_TD_STATUS, 0); /* clear status */ + sonic_tda_put(dev, entry, SONIC_TD_FRAG_COUNT, 1); /* single fragment */ + sonic_tda_put(dev, entry, SONIC_TD_PKTSIZE, length); /* length of packet */ + sonic_tda_put(dev, entry, SONIC_TD_FRAG_PTR_L, laddr & 0xffff); + sonic_tda_put(dev, entry, SONIC_TD_FRAG_PTR_H, laddr >> 16); + sonic_tda_put(dev, entry, SONIC_TD_FRAG_SIZE, length); + sonic_tda_put(dev, entry, SONIC_TD_LINK, + sonic_tda_get(dev, entry, SONIC_TD_LINK) | SONIC_EOL); + + /* + * Must set tx_skb[entry] only after clearing status, and + * before clearing EOL and before stopping queue + */ + wmb(); + lp->tx_len[entry] = length; lp->tx_laddr[entry] = laddr; lp->tx_skb[entry] = skb; - length = (skb->len < ETH_ZLEN) ? ETH_ZLEN : skb->len; - flush_cache_all(); + wmb(); + sonic_tda_put(dev, lp->eol_tx, SONIC_TD_LINK, + sonic_tda_get(dev, lp->eol_tx, SONIC_TD_LINK) & ~SONIC_EOL); + lp->eol_tx = entry; - /* - * Setup the transmit descriptor and issue the transmit command. - */ - lp->tda[entry].tx_status = 0; /* clear status */ - lp->tda[entry].tx_frag_count = 1; /* single fragment */ - lp->tda[entry].tx_pktsize = length; /* length of packet */ - lp->tda[entry].tx_frag_ptr_l = laddr & 0xffff; - lp->tda[entry].tx_frag_ptr_h = laddr >> 16; - lp->tda[entry].tx_frag_size = length; - lp->cur_tx++; - lp->stats.tx_bytes += length; + lp->next_tx = (entry + 1) & SONIC_TDS_MASK; + if (lp->tx_skb[lp->next_tx] != NULL) { + /* The ring is full, the ISR has yet to process the next TD. */ + if (sonic_debug > 3) + printk("%s: stopping queue\n", dev->name); + netif_stop_queue(dev); + /* after this packet, wait for ISR to free up some TDAs */ + } else netif_start_queue(dev); if (sonic_debug > 2) - printk("sonic_send_packet: issueing Tx command\n"); + printk("sonic_send_packet: issuing Tx command\n"); SONIC_WRITE(SONIC_CMD, SONIC_CR_TXP); dev->trans_start = jiffies; - if (lp->cur_tx < lp->dirty_tx + SONIC_NUM_TDS) - netif_start_queue(dev); - else - lp->tx_full = 1; - return 0; } @@ -164,175 +297,199 @@ static int sonic_send_packet(struct sk_buff *skb, struct net_device *dev) static irqreturn_t sonic_interrupt(int irq, void *dev_id, struct pt_regs *regs) { struct net_device *dev = (struct net_device *) dev_id; - unsigned int base_addr = dev->base_addr; - struct sonic_local *lp; + struct sonic_local *lp = netdev_priv(dev); int status; if (dev == NULL) { - printk("sonic_interrupt: irq %d for unknown device.\n", irq); + printk(KERN_ERR "sonic_interrupt: irq %d for unknown device.\n", irq); return IRQ_NONE; } - lp = (struct sonic_local *) dev->priv; - - status = SONIC_READ(SONIC_ISR); - SONIC_WRITE(SONIC_ISR, 0x7fff); /* clear all bits */ - - if (sonic_debug > 2) - printk("sonic_interrupt: ISR=%x\n", status); - - if (status & SONIC_INT_PKTRX) { - sonic_rx(dev); /* got packet(s) */ - } - - if (status & SONIC_INT_TXDN) { - int dirty_tx = lp->dirty_tx; - - while (dirty_tx < lp->cur_tx) { - int entry = dirty_tx & SONIC_TDS_MASK; - int status = lp->tda[entry].tx_status; + if (!(status = SONIC_READ(SONIC_ISR) & SONIC_IMR_DEFAULT)) + return IRQ_NONE; - if (sonic_debug > 3) - printk - ("sonic_interrupt: status %d, cur_tx %d, dirty_tx %d\n", - status, lp->cur_tx, lp->dirty_tx); + do { + if (status & SONIC_INT_PKTRX) { + if (sonic_debug > 2) + printk("%s: packet rx\n", dev->name); + sonic_rx(dev); /* got packet(s) */ + SONIC_WRITE(SONIC_ISR, SONIC_INT_PKTRX); /* clear the interrupt */ + } - if (status == 0) { - /* It still hasn't been Txed, kick the sonic again */ - SONIC_WRITE(SONIC_CMD, SONIC_CR_TXP); - break; - } + if (status & SONIC_INT_TXDN) { + int entry = lp->cur_tx; + int td_status; + int freed_some = 0; - /* put back EOL and free descriptor */ - lp->tda[entry].tx_frag_count = 0; - lp->tda[entry].tx_status = 0; - - if (status & 0x0001) - lp->stats.tx_packets++; - else { - lp->stats.tx_errors++; - if (status & 0x0642) - lp->stats.tx_aborted_errors++; - if (status & 0x0180) - lp->stats.tx_carrier_errors++; - if (status & 0x0020) - lp->stats.tx_window_errors++; - if (status & 0x0004) - lp->stats.tx_fifo_errors++; - } + /* At this point, cur_tx is the index of a TD that is one of: + * unallocated/freed (status set & tx_skb[entry] clear) + * allocated and sent (status set & tx_skb[entry] set ) + * allocated and not yet sent (status clear & tx_skb[entry] set ) + * still being allocated by sonic_send_packet (status clear & tx_skb[entry] clear) + */ - /* We must free the original skb */ - if (lp->tx_skb[entry]) { + if (sonic_debug > 2) + printk("%s: tx done\n", dev->name); + + while (lp->tx_skb[entry] != NULL) { + if ((td_status = sonic_tda_get(dev, entry, SONIC_TD_STATUS)) == 0) + break; + + if (td_status & 0x0001) { + lp->stats.tx_packets++; + lp->stats.tx_bytes += sonic_tda_get(dev, entry, SONIC_TD_PKTSIZE); + } else { + lp->stats.tx_errors++; + if (td_status & 0x0642) + lp->stats.tx_aborted_errors++; + if (td_status & 0x0180) + lp->stats.tx_carrier_errors++; + if (td_status & 0x0020) + lp->stats.tx_window_errors++; + if (td_status & 0x0004) + lp->stats.tx_fifo_errors++; + } + + /* We must free the original skb */ dev_kfree_skb_irq(lp->tx_skb[entry]); - lp->tx_skb[entry] = 0; + lp->tx_skb[entry] = NULL; + /* and unmap DMA buffer */ + dma_unmap_single(lp->device, lp->tx_laddr[entry], lp->tx_len[entry], DMA_TO_DEVICE); + lp->tx_laddr[entry] = (dma_addr_t)0; + freed_some = 1; + + if (sonic_tda_get(dev, entry, SONIC_TD_LINK) & SONIC_EOL) { + entry = (entry + 1) & SONIC_TDS_MASK; + break; + } + entry = (entry + 1) & SONIC_TDS_MASK; } - /* and the VDMA address */ - vdma_free(lp->tx_laddr[entry]); - dirty_tx++; - } - if (lp->tx_full - && dirty_tx + SONIC_NUM_TDS > lp->cur_tx + 2) { - /* The ring is no longer full, clear tbusy. */ - lp->tx_full = 0; - netif_wake_queue(dev); + if (freed_some || lp->tx_skb[entry] == NULL) + netif_wake_queue(dev); /* The ring is no longer full */ + lp->cur_tx = entry; + SONIC_WRITE(SONIC_ISR, SONIC_INT_TXDN); /* clear the interrupt */ } - lp->dirty_tx = dirty_tx; - } + /* + * check error conditions + */ + if (status & SONIC_INT_RFO) { + if (sonic_debug > 1) + printk("%s: rx fifo overrun\n", dev->name); + lp->stats.rx_fifo_errors++; + SONIC_WRITE(SONIC_ISR, SONIC_INT_RFO); /* clear the interrupt */ + } + if (status & SONIC_INT_RDE) { + if (sonic_debug > 1) + printk("%s: rx descriptors exhausted\n", dev->name); + lp->stats.rx_dropped++; + SONIC_WRITE(SONIC_ISR, SONIC_INT_RDE); /* clear the interrupt */ + } + if (status & SONIC_INT_RBAE) { + if (sonic_debug > 1) + printk("%s: rx buffer area exceeded\n", dev->name); + lp->stats.rx_dropped++; + SONIC_WRITE(SONIC_ISR, SONIC_INT_RBAE); /* clear the interrupt */ + } - /* - * check error conditions - */ - if (status & SONIC_INT_RFO) { - printk("%s: receive fifo underrun\n", dev->name); - lp->stats.rx_fifo_errors++; - } - if (status & SONIC_INT_RDE) { - printk("%s: receive descriptors exhausted\n", dev->name); - lp->stats.rx_dropped++; - } - if (status & SONIC_INT_RBE) { - printk("%s: receive buffer exhausted\n", dev->name); - lp->stats.rx_dropped++; - } - if (status & SONIC_INT_RBAE) { - printk("%s: receive buffer area exhausted\n", dev->name); - lp->stats.rx_dropped++; - } + /* counter overruns; all counters are 16bit wide */ + if (status & SONIC_INT_FAE) { + lp->stats.rx_frame_errors += 65536; + SONIC_WRITE(SONIC_ISR, SONIC_INT_FAE); /* clear the interrupt */ + } + if (status & SONIC_INT_CRC) { + lp->stats.rx_crc_errors += 65536; + SONIC_WRITE(SONIC_ISR, SONIC_INT_CRC); /* clear the interrupt */ + } + if (status & SONIC_INT_MP) { + lp->stats.rx_missed_errors += 65536; + SONIC_WRITE(SONIC_ISR, SONIC_INT_MP); /* clear the interrupt */ + } - /* counter overruns; all counters are 16bit wide */ - if (status & SONIC_INT_FAE) - lp->stats.rx_frame_errors += 65536; - if (status & SONIC_INT_CRC) - lp->stats.rx_crc_errors += 65536; - if (status & SONIC_INT_MP) - lp->stats.rx_missed_errors += 65536; + /* transmit error */ + if (status & SONIC_INT_TXER) { + if ((SONIC_READ(SONIC_TCR) & SONIC_TCR_FU) && (sonic_debug > 2)) + printk(KERN_ERR "%s: tx fifo underrun\n", dev->name); + SONIC_WRITE(SONIC_ISR, SONIC_INT_TXER); /* clear the interrupt */ + } - /* transmit error */ - if (status & SONIC_INT_TXER) - lp->stats.tx_errors++; + /* bus retry */ + if (status & SONIC_INT_BR) { + printk(KERN_ERR "%s: Bus retry occurred! Device interrupt disabled.\n", + dev->name); + /* ... to help debug DMA problems causing endless interrupts. */ + /* Bounce the eth interface to turn on the interrupt again. */ + SONIC_WRITE(SONIC_IMR, 0); + SONIC_WRITE(SONIC_ISR, SONIC_INT_BR); /* clear the interrupt */ + } - /* - * clear interrupt bits and return - */ - SONIC_WRITE(SONIC_ISR, status); + /* load CAM done */ + if (status & SONIC_INT_LCD) + SONIC_WRITE(SONIC_ISR, SONIC_INT_LCD); /* clear the interrupt */ + } while((status = SONIC_READ(SONIC_ISR) & SONIC_IMR_DEFAULT)); return IRQ_HANDLED; } /* - * We have a good packet(s), get it/them out of the buffers. + * We have a good packet(s), pass it/them up the network stack. */ static void sonic_rx(struct net_device *dev) { - unsigned int base_addr = dev->base_addr; - struct sonic_local *lp = (struct sonic_local *) dev->priv; - sonic_rd_t *rd = &lp->rda[lp->cur_rx & SONIC_RDS_MASK]; + struct sonic_local *lp = netdev_priv(dev); int status; - - while (rd->in_use == 0) { - struct sk_buff *skb; + int entry = lp->cur_rx; + + while (sonic_rda_get(dev, entry, SONIC_RD_IN_USE) == 0) { + struct sk_buff *used_skb; + struct sk_buff *new_skb; + dma_addr_t new_laddr; + u16 bufadr_l; + u16 bufadr_h; int pkt_len; - unsigned char *pkt_ptr; - status = rd->rx_status; - if (sonic_debug > 3) - printk("status %x, cur_rx %d, cur_rra %x\n", - status, lp->cur_rx, lp->cur_rra); + status = sonic_rda_get(dev, entry, SONIC_RD_STATUS); if (status & SONIC_RCR_PRX) { - pkt_len = rd->rx_pktlen; - pkt_ptr = - (char *) - sonic_chiptomem((rd->rx_pktptr_h << 16) + - rd->rx_pktptr_l); - - if (sonic_debug > 3) - printk - ("pktptr %p (rba %p) h:%x l:%x, bsize h:%x l:%x\n", - pkt_ptr, lp->rba, rd->rx_pktptr_h, - rd->rx_pktptr_l, - SONIC_READ(SONIC_RBWC1), - SONIC_READ(SONIC_RBWC0)); - /* Malloc up new buffer. */ - skb = dev_alloc_skb(pkt_len + 2); - if (skb == NULL) { - printk - ("%s: Memory squeeze, dropping packet.\n", - dev->name); + new_skb = dev_alloc_skb(SONIC_RBSIZE + 2); + if (new_skb == NULL) { + printk(KERN_ERR "%s: Memory squeeze, dropping packet.\n", dev->name); + lp->stats.rx_dropped++; + break; + } + new_skb->dev = dev; + /* provide 16 byte IP header alignment unless DMA requires otherwise */ + if(SONIC_BUS_SCALE(lp->dma_bitmode) == 2) + skb_reserve(new_skb, 2); + + new_laddr = dma_map_single(lp->device, skb_put(new_skb, SONIC_RBSIZE), + SONIC_RBSIZE, DMA_FROM_DEVICE); + if (!new_laddr) { + dev_kfree_skb(new_skb); + printk(KERN_ERR "%s: Failed to map rx buffer, dropping packet.\n", dev->name); lp->stats.rx_dropped++; break; } - skb->dev = dev; - skb_reserve(skb, 2); /* 16 byte align */ - skb_put(skb, pkt_len); /* Make room */ - eth_copy_and_sum(skb, pkt_ptr, pkt_len, 0); - skb->protocol = eth_type_trans(skb, dev); - netif_rx(skb); /* pass the packet to upper layers */ + + /* now we have a new skb to replace it, pass the used one up the stack */ + dma_unmap_single(lp->device, lp->rx_laddr[entry], SONIC_RBSIZE, DMA_FROM_DEVICE); + used_skb = lp->rx_skb[entry]; + pkt_len = sonic_rda_get(dev, entry, SONIC_RD_PKTLEN); + skb_trim(used_skb, pkt_len); + used_skb->protocol = eth_type_trans(used_skb, dev); + netif_rx(used_skb); dev->last_rx = jiffies; lp->stats.rx_packets++; lp->stats.rx_bytes += pkt_len; + /* and insert the new skb */ + lp->rx_laddr[entry] = new_laddr; + lp->rx_skb[entry] = new_skb; + + bufadr_l = (unsigned long)new_laddr & 0xffff; + bufadr_h = (unsigned long)new_laddr >> 16; + sonic_rra_put(dev, entry, SONIC_RR_BUFADR_L, bufadr_l); + sonic_rra_put(dev, entry, SONIC_RR_BUFADR_H, bufadr_h); } else { /* This should only happen, if we enable accepting broken packets. */ lp->stats.rx_errors++; @@ -341,29 +498,35 @@ static void sonic_rx(struct net_device *dev) if (status & SONIC_RCR_CRCR) lp->stats.rx_crc_errors++; } - - rd->in_use = 1; - rd = &lp->rda[(++lp->cur_rx) & SONIC_RDS_MASK]; - /* now give back the buffer to the receive buffer area */ if (status & SONIC_RCR_LPKT) { /* - * this was the last packet out of the current receice buffer + * this was the last packet out of the current receive buffer * give the buffer back to the SONIC */ - lp->cur_rra += sizeof(sonic_rr_t); - if (lp->cur_rra > - (lp->rra_laddr + - (SONIC_NUM_RRS - - 1) * sizeof(sonic_rr_t))) lp->cur_rra = - lp->rra_laddr; - SONIC_WRITE(SONIC_RWP, lp->cur_rra & 0xffff); + lp->cur_rwp += SIZEOF_SONIC_RR * SONIC_BUS_SCALE(lp->dma_bitmode); + if (lp->cur_rwp >= lp->rra_end) lp->cur_rwp = lp->rra_laddr & 0xffff; + SONIC_WRITE(SONIC_RWP, lp->cur_rwp); + if (SONIC_READ(SONIC_ISR) & SONIC_INT_RBE) { + if (sonic_debug > 2) + printk("%s: rx buffer exhausted\n", dev->name); + SONIC_WRITE(SONIC_ISR, SONIC_INT_RBE); /* clear the flag */ + } } else - printk - ("%s: rx desc without RCR_LPKT. Shouldn't happen !?\n", + printk(KERN_ERR "%s: rx desc without RCR_LPKT. Shouldn't happen !?\n", dev->name); + /* + * give back the descriptor + */ + sonic_rda_put(dev, entry, SONIC_RD_LINK, + sonic_rda_get(dev, entry, SONIC_RD_LINK) | SONIC_EOL); + sonic_rda_put(dev, entry, SONIC_RD_IN_USE, 1); + sonic_rda_put(dev, lp->eol_rx, SONIC_RD_LINK, + sonic_rda_get(dev, lp->eol_rx, SONIC_RD_LINK) & ~SONIC_EOL); + lp->eol_rx = entry; + lp->cur_rx = entry = (entry + 1) & SONIC_RDS_MASK; } /* - * If any worth-while packets have been received, dev_rint() + * If any worth-while packets have been received, netif_rx() * has done a mark_bh(NET_BH) for us and will work on them * when we get to the bottom-half routine. */ @@ -376,8 +539,7 @@ static void sonic_rx(struct net_device *dev) */ static struct net_device_stats *sonic_get_stats(struct net_device *dev) { - struct sonic_local *lp = (struct sonic_local *) dev->priv; - unsigned int base_addr = dev->base_addr; + struct sonic_local *lp = netdev_priv(dev); /* read the tally counter from the SONIC and reset them */ lp->stats.rx_crc_errors += SONIC_READ(SONIC_CRCT); @@ -396,8 +558,7 @@ static struct net_device_stats *sonic_get_stats(struct net_device *dev) */ static void sonic_multicast_list(struct net_device *dev) { - struct sonic_local *lp = (struct sonic_local *) dev->priv; - unsigned int base_addr = dev->base_addr; + struct sonic_local *lp = netdev_priv(dev); unsigned int rcr; struct dev_mc_list *dmi = dev->mc_list; unsigned char *addr; @@ -413,20 +574,15 @@ static void sonic_multicast_list(struct net_device *dev) rcr |= SONIC_RCR_AMC; } else { if (sonic_debug > 2) - printk - ("sonic_multicast_list: mc_count %d\n", - dev->mc_count); - lp->cda.cam_enable = 1; /* always enable our own address */ + printk("sonic_multicast_list: mc_count %d\n", dev->mc_count); + sonic_set_cam_enable(dev, 1); /* always enable our own address */ for (i = 1; i <= dev->mc_count; i++) { addr = dmi->dmi_addr; dmi = dmi->next; - lp->cda.cam_desc[i].cam_cap0 = - addr[1] << 8 | addr[0]; - lp->cda.cam_desc[i].cam_cap1 = - addr[3] << 8 | addr[2]; - lp->cda.cam_desc[i].cam_cap2 = - addr[5] << 8 | addr[4]; - lp->cda.cam_enable |= (1 << i); + sonic_cda_put(dev, i, SONIC_CD_CAP0, addr[1] << 8 | addr[0]); + sonic_cda_put(dev, i, SONIC_CD_CAP1, addr[3] << 8 | addr[2]); + sonic_cda_put(dev, i, SONIC_CD_CAP2, addr[5] << 8 | addr[4]); + sonic_set_cam_enable(dev, sonic_get_cam_enable(dev) | (1 << i)); } SONIC_WRITE(SONIC_CDC, 16); /* issue Load CAM command */ @@ -447,19 +603,16 @@ static void sonic_multicast_list(struct net_device *dev) */ static int sonic_init(struct net_device *dev) { - unsigned int base_addr = dev->base_addr; unsigned int cmd; - struct sonic_local *lp = (struct sonic_local *) dev->priv; - unsigned int rra_start; - unsigned int rra_end; + struct sonic_local *lp = netdev_priv(dev); int i; /* * put the Sonic into software-reset mode and * disable all interrupts */ - SONIC_WRITE(SONIC_ISR, 0x7fff); SONIC_WRITE(SONIC_IMR, 0); + SONIC_WRITE(SONIC_ISR, 0x7fff); SONIC_WRITE(SONIC_CMD, SONIC_CR_RST); /* @@ -475,34 +628,32 @@ static int sonic_init(struct net_device *dev) if (sonic_debug > 2) printk("sonic_init: initialize receive resource area\n"); - rra_start = lp->rra_laddr & 0xffff; - rra_end = - (rra_start + (SONIC_NUM_RRS * sizeof(sonic_rr_t))) & 0xffff; - for (i = 0; i < SONIC_NUM_RRS; i++) { - lp->rra[i].rx_bufadr_l = - (lp->rba_laddr + i * SONIC_RBSIZE) & 0xffff; - lp->rra[i].rx_bufadr_h = - (lp->rba_laddr + i * SONIC_RBSIZE) >> 16; - lp->rra[i].rx_bufsize_l = SONIC_RBSIZE >> 1; - lp->rra[i].rx_bufsize_h = 0; + u16 bufadr_l = (unsigned long)lp->rx_laddr[i] & 0xffff; + u16 bufadr_h = (unsigned long)lp->rx_laddr[i] >> 16; + sonic_rra_put(dev, i, SONIC_RR_BUFADR_L, bufadr_l); + sonic_rra_put(dev, i, SONIC_RR_BUFADR_H, bufadr_h); + sonic_rra_put(dev, i, SONIC_RR_BUFSIZE_L, SONIC_RBSIZE >> 1); + sonic_rra_put(dev, i, SONIC_RR_BUFSIZE_H, 0); } /* initialize all RRA registers */ - SONIC_WRITE(SONIC_RSA, rra_start); - SONIC_WRITE(SONIC_REA, rra_end); - SONIC_WRITE(SONIC_RRP, rra_start); - SONIC_WRITE(SONIC_RWP, rra_end); + lp->rra_end = (lp->rra_laddr + SONIC_NUM_RRS * SIZEOF_SONIC_RR * + SONIC_BUS_SCALE(lp->dma_bitmode)) & 0xffff; + lp->cur_rwp = (lp->rra_laddr + (SONIC_NUM_RRS - 1) * SIZEOF_SONIC_RR * + SONIC_BUS_SCALE(lp->dma_bitmode)) & 0xffff; + + SONIC_WRITE(SONIC_RSA, lp->rra_laddr & 0xffff); + SONIC_WRITE(SONIC_REA, lp->rra_end); + SONIC_WRITE(SONIC_RRP, lp->rra_laddr & 0xffff); + SONIC_WRITE(SONIC_RWP, lp->cur_rwp); SONIC_WRITE(SONIC_URRA, lp->rra_laddr >> 16); - SONIC_WRITE(SONIC_EOBC, (SONIC_RBSIZE - 2) >> 1); - - lp->cur_rra = - lp->rra_laddr + (SONIC_NUM_RRS - 1) * sizeof(sonic_rr_t); + SONIC_WRITE(SONIC_EOBC, (SONIC_RBSIZE >> 1) - (lp->dma_bitmode ? 2 : 1)); /* load the resource pointers */ if (sonic_debug > 3) - printk("sonic_init: issueing RRRA command\n"); - + printk("sonic_init: issuing RRRA command\n"); + SONIC_WRITE(SONIC_CMD, SONIC_CR_RRRA); i = 0; while (i++ < 100) { @@ -511,27 +662,30 @@ static int sonic_init(struct net_device *dev) } if (sonic_debug > 2) - printk("sonic_init: status=%x\n", SONIC_READ(SONIC_CMD)); - + printk("sonic_init: status=%x i=%d\n", SONIC_READ(SONIC_CMD), i); + /* * Initialize the receive descriptors so that they * become a circular linked list, ie. let the last * descriptor point to the first again. */ if (sonic_debug > 2) - printk("sonic_init: initialize receive descriptors\n"); - for (i = 0; i < SONIC_NUM_RDS; i++) { - lp->rda[i].rx_status = 0; - lp->rda[i].rx_pktlen = 0; - lp->rda[i].rx_pktptr_l = 0; - lp->rda[i].rx_pktptr_h = 0; - lp->rda[i].rx_seqno = 0; - lp->rda[i].in_use = 1; - lp->rda[i].link = - lp->rda_laddr + (i + 1) * sizeof(sonic_rd_t); + printk("sonic_init: initialize receive descriptors\n"); + for (i=0; irda_laddr + + ((i+1) * SIZEOF_SONIC_RD * SONIC_BUS_SCALE(lp->dma_bitmode))); } /* fix last descriptor */ - lp->rda[SONIC_NUM_RDS - 1].link = lp->rda_laddr; + sonic_rda_put(dev, SONIC_NUM_RDS - 1, SONIC_RD_LINK, + (lp->rda_laddr & 0xffff) | SONIC_EOL); + lp->eol_rx = SONIC_NUM_RDS - 1; lp->cur_rx = 0; SONIC_WRITE(SONIC_URDA, lp->rda_laddr >> 16); SONIC_WRITE(SONIC_CRDA, lp->rda_laddr & 0xffff); @@ -542,34 +696,34 @@ static int sonic_init(struct net_device *dev) if (sonic_debug > 2) printk("sonic_init: initialize transmit descriptors\n"); for (i = 0; i < SONIC_NUM_TDS; i++) { - lp->tda[i].tx_status = 0; - lp->tda[i].tx_config = 0; - lp->tda[i].tx_pktsize = 0; - lp->tda[i].tx_frag_count = 0; - lp->tda[i].link = - (lp->tda_laddr + - (i + 1) * sizeof(sonic_td_t)) | SONIC_END_OF_LINKS; + sonic_tda_put(dev, i, SONIC_TD_STATUS, 0); + sonic_tda_put(dev, i, SONIC_TD_CONFIG, 0); + sonic_tda_put(dev, i, SONIC_TD_PKTSIZE, 0); + sonic_tda_put(dev, i, SONIC_TD_FRAG_COUNT, 0); + sonic_tda_put(dev, i, SONIC_TD_LINK, + (lp->tda_laddr & 0xffff) + + (i + 1) * SIZEOF_SONIC_TD * SONIC_BUS_SCALE(lp->dma_bitmode)); + lp->tx_skb[i] = NULL; } - lp->tda[SONIC_NUM_TDS - 1].link = - (lp->tda_laddr & 0xffff) | SONIC_END_OF_LINKS; + /* fix last descriptor */ + sonic_tda_put(dev, SONIC_NUM_TDS - 1, SONIC_TD_LINK, + (lp->tda_laddr & 0xffff)); SONIC_WRITE(SONIC_UTDA, lp->tda_laddr >> 16); SONIC_WRITE(SONIC_CTDA, lp->tda_laddr & 0xffff); - lp->cur_tx = lp->dirty_tx = 0; - + lp->cur_tx = lp->next_tx = 0; + lp->eol_tx = SONIC_NUM_TDS - 1; + /* * put our own address to CAM desc[0] */ - lp->cda.cam_desc[0].cam_cap0 = - dev->dev_addr[1] << 8 | dev->dev_addr[0]; - lp->cda.cam_desc[0].cam_cap1 = - dev->dev_addr[3] << 8 | dev->dev_addr[2]; - lp->cda.cam_desc[0].cam_cap2 = - dev->dev_addr[5] << 8 | dev->dev_addr[4]; - lp->cda.cam_enable = 1; + sonic_cda_put(dev, 0, SONIC_CD_CAP0, dev->dev_addr[1] << 8 | dev->dev_addr[0]); + sonic_cda_put(dev, 0, SONIC_CD_CAP1, dev->dev_addr[3] << 8 | dev->dev_addr[2]); + sonic_cda_put(dev, 0, SONIC_CD_CAP2, dev->dev_addr[5] << 8 | dev->dev_addr[4]); + sonic_set_cam_enable(dev, 1); for (i = 0; i < 16; i++) - lp->cda.cam_desc[i].cam_entry_pointer = i; + sonic_cda_put(dev, i, SONIC_CD_ENTRY_POINTER, i); /* * initialize CAM registers @@ -588,8 +742,8 @@ static int sonic_init(struct net_device *dev) break; } if (sonic_debug > 2) { - printk("sonic_init: CMD=%x, ISR=%x\n", - SONIC_READ(SONIC_CMD), SONIC_READ(SONIC_ISR)); + printk("sonic_init: CMD=%x, ISR=%x\n, i=%d", + SONIC_READ(SONIC_CMD), SONIC_READ(SONIC_ISR), i); } /* @@ -604,7 +758,7 @@ static int sonic_init(struct net_device *dev) cmd = SONIC_READ(SONIC_CMD); if ((cmd & SONIC_CR_RXEN) == 0 || (cmd & SONIC_CR_STP) == 0) - printk("sonic_init: failed, status=%x\n", cmd); + printk(KERN_ERR "sonic_init: failed, status=%x\n", cmd); if (sonic_debug > 2) printk("sonic_init: new status=%x\n", diff --git a/drivers/net/sonic.h b/drivers/net/sonic.h index c4a6d58..cede969a 100644 --- a/drivers/net/sonic.h +++ b/drivers/net/sonic.h @@ -1,5 +1,5 @@ /* - * Helpfile for sonic.c + * Header file for sonic.c * * (C) Waldorf Electronics, Germany * Written by Andreas Busse @@ -9,10 +9,16 @@ * and pad structure members must be exchanged. Also, the structures * need to be changed accordingly to the bus size. * - * 981229 MSch: did just that for the 68k Mac port (32 bit, big endian), - * see CONFIG_MACSONIC branch below. + * 981229 MSch: did just that for the 68k Mac port (32 bit, big endian) * + * 990611 David Huggins-Daines : This machine abstraction + * does not cope with 16-bit bus sizes very well. Therefore I have + * rewritten it with ugly macros and evil inlines. + * + * 050625 Finn Thain: introduced more 32-bit cards and dhd's support + * for 16-bit cards (from the mac68k project). */ + #ifndef SONIC_H #define SONIC_H @@ -83,6 +89,7 @@ /* * Error counters */ + #define SONIC_CRCT 0x2c #define SONIC_FAET 0x2d #define SONIC_MPT 0x2e @@ -182,14 +189,14 @@ #define SONIC_INT_BR 0x4000 #define SONIC_INT_HBL 0x2000 -#define SONIC_INT_LCD 0x1000 -#define SONIC_INT_PINT 0x0800 -#define SONIC_INT_PKTRX 0x0400 -#define SONIC_INT_TXDN 0x0200 -#define SONIC_INT_TXER 0x0100 -#define SONIC_INT_TC 0x0080 -#define SONIC_INT_RDE 0x0040 -#define SONIC_INT_RBE 0x0020 +#define SONIC_INT_LCD 0x1000 +#define SONIC_INT_PINT 0x0800 +#define SONIC_INT_PKTRX 0x0400 +#define SONIC_INT_TXDN 0x0200 +#define SONIC_INT_TXER 0x0100 +#define SONIC_INT_TC 0x0080 +#define SONIC_INT_RDE 0x0040 +#define SONIC_INT_RBE 0x0020 #define SONIC_INT_RBAE 0x0010 #define SONIC_INT_CRC 0x0008 #define SONIC_INT_FAE 0x0004 @@ -201,224 +208,61 @@ * The interrupts we allow. */ -#define SONIC_IMR_DEFAULT (SONIC_INT_BR | \ - SONIC_INT_LCD | \ - SONIC_INT_PINT | \ +#define SONIC_IMR_DEFAULT ( SONIC_INT_BR | \ + SONIC_INT_LCD | \ + SONIC_INT_RFO | \ SONIC_INT_PKTRX | \ SONIC_INT_TXDN | \ SONIC_INT_TXER | \ SONIC_INT_RDE | \ - SONIC_INT_RBE | \ SONIC_INT_RBAE | \ SONIC_INT_CRC | \ SONIC_INT_FAE | \ SONIC_INT_MP) -#define SONIC_END_OF_LINKS 0x0001 - - -#ifdef CONFIG_MACSONIC -/* - * Big endian like structures on 680x0 Macs - */ - -typedef struct { - u32 rx_bufadr_l; /* receive buffer ptr */ - u32 rx_bufadr_h; - - u32 rx_bufsize_l; /* no. of words in the receive buffer */ - u32 rx_bufsize_h; -} sonic_rr_t; - -/* - * Sonic receive descriptor. Receive descriptors are - * kept in a linked list of these structures. - */ - -typedef struct { - SREGS_PAD(pad0); - u16 rx_status; /* status after reception of a packet */ - SREGS_PAD(pad1); - u16 rx_pktlen; /* length of the packet incl. CRC */ - - /* - * Pointers to the location in the receive buffer area (RBA) - * where the packet resides. A packet is always received into - * a contiguous piece of memory. - */ - SREGS_PAD(pad2); - u16 rx_pktptr_l; - SREGS_PAD(pad3); - u16 rx_pktptr_h; - - SREGS_PAD(pad4); - u16 rx_seqno; /* sequence no. */ - - SREGS_PAD(pad5); - u16 link; /* link to next RDD (end if EOL bit set) */ - - /* - * Owner of this descriptor, 0= driver, 1=sonic - */ - - SREGS_PAD(pad6); - u16 in_use; - - caddr_t rda_next; /* pointer to next RD */ -} sonic_rd_t; - - -/* - * Describes a Transmit Descriptor - */ -typedef struct { - SREGS_PAD(pad0); - u16 tx_status; /* status after transmission of a packet */ - SREGS_PAD(pad1); - u16 tx_config; /* transmit configuration for this packet */ - SREGS_PAD(pad2); - u16 tx_pktsize; /* size of the packet to be transmitted */ - SREGS_PAD(pad3); - u16 tx_frag_count; /* no. of fragments */ - - SREGS_PAD(pad4); - u16 tx_frag_ptr_l; - SREGS_PAD(pad5); - u16 tx_frag_ptr_h; - SREGS_PAD(pad6); - u16 tx_frag_size; - - SREGS_PAD(pad7); - u16 link; /* ptr to next descriptor */ -} sonic_td_t; - - -/* - * Describes an entry in the CAM Descriptor Area. - */ - -typedef struct { - SREGS_PAD(pad0); - u16 cam_entry_pointer; - SREGS_PAD(pad1); - u16 cam_cap0; - SREGS_PAD(pad2); - u16 cam_cap1; - SREGS_PAD(pad3); - u16 cam_cap2; -} sonic_cd_t; - +#define SONIC_EOL 0x0001 #define CAM_DESCRIPTORS 16 - -typedef struct { - sonic_cd_t cam_desc[CAM_DESCRIPTORS]; - SREGS_PAD(pad); - u16 cam_enable; -} sonic_cda_t; - -#else /* original declarations, little endian 32 bit */ - -/* - * structure definitions - */ - -typedef struct { - u32 rx_bufadr_l; /* receive buffer ptr */ - u32 rx_bufadr_h; - - u32 rx_bufsize_l; /* no. of words in the receive buffer */ - u32 rx_bufsize_h; -} sonic_rr_t; - -/* - * Sonic receive descriptor. Receive descriptors are - * kept in a linked list of these structures. - */ - -typedef struct { - u16 rx_status; /* status after reception of a packet */ - SREGS_PAD(pad0); - u16 rx_pktlen; /* length of the packet incl. CRC */ - SREGS_PAD(pad1); - - /* - * Pointers to the location in the receive buffer area (RBA) - * where the packet resides. A packet is always received into - * a contiguous piece of memory. - */ - u16 rx_pktptr_l; - SREGS_PAD(pad2); - u16 rx_pktptr_h; - SREGS_PAD(pad3); - - u16 rx_seqno; /* sequence no. */ - SREGS_PAD(pad4); - - u16 link; /* link to next RDD (end if EOL bit set) */ - SREGS_PAD(pad5); - - /* - * Owner of this descriptor, 0= driver, 1=sonic - */ - - u16 in_use; - SREGS_PAD(pad6); - - caddr_t rda_next; /* pointer to next RD */ -} sonic_rd_t; - - -/* - * Describes a Transmit Descriptor - */ -typedef struct { - u16 tx_status; /* status after transmission of a packet */ - SREGS_PAD(pad0); - u16 tx_config; /* transmit configuration for this packet */ - SREGS_PAD(pad1); - u16 tx_pktsize; /* size of the packet to be transmitted */ - SREGS_PAD(pad2); - u16 tx_frag_count; /* no. of fragments */ - SREGS_PAD(pad3); - - u16 tx_frag_ptr_l; - SREGS_PAD(pad4); - u16 tx_frag_ptr_h; - SREGS_PAD(pad5); - u16 tx_frag_size; - SREGS_PAD(pad6); - - u16 link; /* ptr to next descriptor */ - SREGS_PAD(pad7); -} sonic_td_t; - - -/* - * Describes an entry in the CAM Descriptor Area. - */ - -typedef struct { - u16 cam_entry_pointer; - SREGS_PAD(pad0); - u16 cam_cap0; - SREGS_PAD(pad1); - u16 cam_cap1; - SREGS_PAD(pad2); - u16 cam_cap2; - SREGS_PAD(pad3); -} sonic_cd_t; - -#define CAM_DESCRIPTORS 16 - - -typedef struct { - sonic_cd_t cam_desc[CAM_DESCRIPTORS]; - u16 cam_enable; - SREGS_PAD(pad); -} sonic_cda_t; -#endif /* endianness */ +/* Offsets in the various DMA buffers accessed by the SONIC */ + +#define SONIC_BITMODE16 0 +#define SONIC_BITMODE32 1 +#define SONIC_BUS_SCALE(bitmode) ((bitmode) ? 4 : 2) +/* Note! These are all measured in bus-size units, so use SONIC_BUS_SCALE */ +#define SIZEOF_SONIC_RR 4 +#define SONIC_RR_BUFADR_L 0 +#define SONIC_RR_BUFADR_H 1 +#define SONIC_RR_BUFSIZE_L 2 +#define SONIC_RR_BUFSIZE_H 3 + +#define SIZEOF_SONIC_RD 7 +#define SONIC_RD_STATUS 0 +#define SONIC_RD_PKTLEN 1 +#define SONIC_RD_PKTPTR_L 2 +#define SONIC_RD_PKTPTR_H 3 +#define SONIC_RD_SEQNO 4 +#define SONIC_RD_LINK 5 +#define SONIC_RD_IN_USE 6 + +#define SIZEOF_SONIC_TD 8 +#define SONIC_TD_STATUS 0 +#define SONIC_TD_CONFIG 1 +#define SONIC_TD_PKTSIZE 2 +#define SONIC_TD_FRAG_COUNT 3 +#define SONIC_TD_FRAG_PTR_L 4 +#define SONIC_TD_FRAG_PTR_H 5 +#define SONIC_TD_FRAG_SIZE 6 +#define SONIC_TD_LINK 7 + +#define SIZEOF_SONIC_CD 4 +#define SONIC_CD_ENTRY_POINTER 0 +#define SONIC_CD_CAP0 1 +#define SONIC_CD_CAP1 2 +#define SONIC_CD_CAP2 3 + +#define SIZEOF_SONIC_CDA ((CAM_DESCRIPTORS * SIZEOF_SONIC_CD) + 1) +#define SONIC_CDA_CAM_ENABLE (CAM_DESCRIPTORS * SIZEOF_SONIC_CD) /* * Some tunables for the buffer areas. Power of 2 is required @@ -426,44 +270,60 @@ typedef struct { * * MSch: use more buffer space for the slow m68k Macs! */ -#ifdef CONFIG_MACSONIC -#define SONIC_NUM_RRS 32 /* number of receive resources */ -#define SONIC_NUM_RDS SONIC_NUM_RRS /* number of receive descriptors */ -#define SONIC_NUM_TDS 32 /* number of transmit descriptors */ -#else -#define SONIC_NUM_RRS 16 /* number of receive resources */ -#define SONIC_NUM_RDS SONIC_NUM_RRS /* number of receive descriptors */ -#define SONIC_NUM_TDS 16 /* number of transmit descriptors */ -#endif -#define SONIC_RBSIZE 1520 /* size of one resource buffer */ +#define SONIC_NUM_RRS 16 /* number of receive resources */ +#define SONIC_NUM_RDS SONIC_NUM_RRS /* number of receive descriptors */ +#define SONIC_NUM_TDS 16 /* number of transmit descriptors */ -#define SONIC_RDS_MASK (SONIC_NUM_RDS-1) -#define SONIC_TDS_MASK (SONIC_NUM_TDS-1) +#define SONIC_RDS_MASK (SONIC_NUM_RDS-1) +#define SONIC_TDS_MASK (SONIC_NUM_TDS-1) +#define SONIC_RBSIZE 1520 /* size of one resource buffer */ + +/* Again, measured in bus size units! */ +#define SIZEOF_SONIC_DESC (SIZEOF_SONIC_CDA \ + + (SIZEOF_SONIC_TD * SONIC_NUM_TDS) \ + + (SIZEOF_SONIC_RD * SONIC_NUM_RDS) \ + + (SIZEOF_SONIC_RR * SONIC_NUM_RRS)) /* Information that need to be kept for each board. */ struct sonic_local { - sonic_cda_t cda; /* virtual CPU address of CDA */ - sonic_td_t tda[SONIC_NUM_TDS]; /* transmit descriptor area */ - sonic_rr_t rra[SONIC_NUM_RRS]; /* receive resource area */ - sonic_rd_t rda[SONIC_NUM_RDS]; /* receive descriptor area */ - struct sk_buff *tx_skb[SONIC_NUM_TDS]; /* skbuffs for packets to transmit */ - unsigned int tx_laddr[SONIC_NUM_TDS]; /* logical DMA address fro skbuffs */ - unsigned char *rba; /* start of receive buffer areas */ - unsigned int cda_laddr; /* logical DMA address of CDA */ - unsigned int tda_laddr; /* logical DMA address of TDA */ - unsigned int rra_laddr; /* logical DMA address of RRA */ - unsigned int rda_laddr; /* logical DMA address of RDA */ - unsigned int rba_laddr; /* logical DMA address of RBA */ - unsigned int cur_rra; /* current indexes to resource areas */ + /* Bus size. 0 == 16 bits, 1 == 32 bits. */ + int dma_bitmode; + /* Register offset within the longword (independent of endianness, + and varies from one type of Macintosh SONIC to another + (Aarrgh)) */ + int reg_offset; + void *descriptors; + /* Crud. These areas have to be within the same 64K. Therefore + we allocate a desriptors page, and point these to places within it. */ + void *cda; /* CAM descriptor area */ + void *tda; /* Transmit descriptor area */ + void *rra; /* Receive resource area */ + void *rda; /* Receive descriptor area */ + struct sk_buff* volatile rx_skb[SONIC_NUM_RRS]; /* packets to be received */ + struct sk_buff* volatile tx_skb[SONIC_NUM_TDS]; /* packets to be transmitted */ + unsigned int tx_len[SONIC_NUM_TDS]; /* lengths of tx DMA mappings */ + /* Logical DMA addresses on MIPS, bus addresses on m68k + * (so "laddr" is a bit misleading) */ + dma_addr_t descriptors_laddr; + u32 cda_laddr; /* logical DMA address of CDA */ + u32 tda_laddr; /* logical DMA address of TDA */ + u32 rra_laddr; /* logical DMA address of RRA */ + u32 rda_laddr; /* logical DMA address of RDA */ + dma_addr_t rx_laddr[SONIC_NUM_RRS]; /* logical DMA addresses of rx skbuffs */ + dma_addr_t tx_laddr[SONIC_NUM_TDS]; /* logical DMA addresses of tx skbuffs */ + unsigned int rra_end; + unsigned int cur_rwp; unsigned int cur_rx; - unsigned int cur_tx; - unsigned int dirty_tx; /* last unacked transmit packet */ - char tx_full; + unsigned int cur_tx; /* first unacked transmit packet */ + unsigned int eol_rx; + unsigned int eol_tx; /* last unacked transmit packet */ + unsigned int next_tx; /* next free TD */ + struct device *device; /* generic device */ struct net_device_stats stats; }; -#define TX_TIMEOUT 6 +#define TX_TIMEOUT (3 * HZ) /* Index to functions, as function prototypes. */ @@ -477,6 +337,114 @@ static void sonic_multicast_list(struct net_device *dev); static int sonic_init(struct net_device *dev); static void sonic_tx_timeout(struct net_device *dev); +/* Internal inlines for reading/writing DMA buffers. Note that bus + size and endianness matter here, whereas they don't for registers, + as far as we can tell. */ +/* OpenBSD calls this "SWO". I'd like to think that sonic_buf_put() + is a much better name. */ +static inline void sonic_buf_put(void* base, int bitmode, + int offset, __u16 val) +{ + if (bitmode) +#ifdef __BIG_ENDIAN + ((__u16 *) base + (offset*2))[1] = val; +#else + ((__u16 *) base + (offset*2))[0] = val; +#endif + else + ((__u16 *) base)[offset] = val; +} + +static inline __u16 sonic_buf_get(void* base, int bitmode, + int offset) +{ + if (bitmode) +#ifdef __BIG_ENDIAN + return ((volatile __u16 *) base + (offset*2))[1]; +#else + return ((volatile __u16 *) base + (offset*2))[0]; +#endif + else + return ((volatile __u16 *) base)[offset]; +} + +/* Inlines that you should actually use for reading/writing DMA buffers */ +static inline void sonic_cda_put(struct net_device* dev, int entry, + int offset, __u16 val) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + sonic_buf_put(lp->cda, lp->dma_bitmode, + (entry * SIZEOF_SONIC_CD) + offset, val); +} + +static inline __u16 sonic_cda_get(struct net_device* dev, int entry, + int offset) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + return sonic_buf_get(lp->cda, lp->dma_bitmode, + (entry * SIZEOF_SONIC_CD) + offset); +} + +static inline void sonic_set_cam_enable(struct net_device* dev, __u16 val) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + sonic_buf_put(lp->cda, lp->dma_bitmode, SONIC_CDA_CAM_ENABLE, val); +} + +static inline __u16 sonic_get_cam_enable(struct net_device* dev) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + return sonic_buf_get(lp->cda, lp->dma_bitmode, SONIC_CDA_CAM_ENABLE); +} + +static inline void sonic_tda_put(struct net_device* dev, int entry, + int offset, __u16 val) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + sonic_buf_put(lp->tda, lp->dma_bitmode, + (entry * SIZEOF_SONIC_TD) + offset, val); +} + +static inline __u16 sonic_tda_get(struct net_device* dev, int entry, + int offset) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + return sonic_buf_get(lp->tda, lp->dma_bitmode, + (entry * SIZEOF_SONIC_TD) + offset); +} + +static inline void sonic_rda_put(struct net_device* dev, int entry, + int offset, __u16 val) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + sonic_buf_put(lp->rda, lp->dma_bitmode, + (entry * SIZEOF_SONIC_RD) + offset, val); +} + +static inline __u16 sonic_rda_get(struct net_device* dev, int entry, + int offset) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + return sonic_buf_get(lp->rda, lp->dma_bitmode, + (entry * SIZEOF_SONIC_RD) + offset); +} + +static inline void sonic_rra_put(struct net_device* dev, int entry, + int offset, __u16 val) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + sonic_buf_put(lp->rra, lp->dma_bitmode, + (entry * SIZEOF_SONIC_RR) + offset, val); +} + +static inline __u16 sonic_rra_get(struct net_device* dev, int entry, + int offset) +{ + struct sonic_local* lp = (struct sonic_local *) dev->priv; + return sonic_buf_get(lp->rra, lp->dma_bitmode, + (entry * SIZEOF_SONIC_RR) + offset); +} + static const char *version = "sonic.c:v0.92 20.9.98 tsbogend@alpha.franken.de\n"; -- cgit v0.10.2 From 8531c5ffbca65f6df868637c26e6df6f88bff738 Mon Sep 17 00:00:00 2001 From: Arthur Kepner Date: Tue, 23 Aug 2005 01:34:53 -0400 Subject: [PATCH] bonding: inherit zero-copy flags of slaves This change allows a bonding device to inherit the "zero-copy" features of its slave devices. It was inspired by a couple of previous postings on this topic: http://marc.theaimsgroup.com/?l=bonding-devel&m=111924607327794&w=2 http://marc.theaimsgroup.com/?l=bonding-devel&m=111925242706297&w=2 and it's largely a combination of the patches that appear in those emails. Signed-off-by: Arthur Kepner diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 2c930da..94c9f68 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1604,6 +1604,44 @@ static int bond_sethwaddr(struct net_device *bond_dev, struct net_device *slave_ return 0; } +#define BOND_INTERSECT_FEATURES \ + (NETIF_F_SG|NETIF_F_IP_CSUM|NETIF_F_NO_CSUM|NETIF_F_HW_CSUM) + +/* + * Compute the features available to the bonding device by + * intersection of all of the slave devices' BOND_INTERSECT_FEATURES. + * Call this after attaching or detaching a slave to update the + * bond's features. + */ +static int bond_compute_features(struct bonding *bond) +{ + int i; + struct slave *slave; + struct net_device *bond_dev = bond->dev; + int features = bond->bond_features; + + bond_for_each_slave(bond, slave, i) { + struct net_device * slave_dev = slave->dev; + if (i == 0) { + features |= BOND_INTERSECT_FEATURES; + } + features &= + ~(~slave_dev->features & BOND_INTERSECT_FEATURES); + } + + /* turn off NETIF_F_SG if we need a csum and h/w can't do it */ + if ((features & NETIF_F_SG) && + !(features & (NETIF_F_IP_CSUM | + NETIF_F_NO_CSUM | + NETIF_F_HW_CSUM))) { + features &= ~NETIF_F_SG; + } + + bond_dev->features = features; + + return 0; +} + /* enslave device to bond device */ static int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev) { @@ -1811,6 +1849,8 @@ static int bond_enslave(struct net_device *bond_dev, struct net_device *slave_de new_slave->delay = 0; new_slave->link_failure_count = 0; + bond_compute_features(bond); + if (bond->params.miimon && !bond->params.use_carrier) { link_reporting = bond_check_dev_link(bond, slave_dev, 1); @@ -2015,7 +2055,7 @@ err_free: err_undo_flags: bond_dev->features = old_features; - + return res; } @@ -2100,6 +2140,8 @@ static int bond_release(struct net_device *bond_dev, struct net_device *slave_de /* release the slave from its bond */ bond_detach_slave(bond, slave); + bond_compute_features(bond); + if (bond->primary_slave == slave) { bond->primary_slave = NULL; } @@ -2243,6 +2285,8 @@ static int bond_release_all(struct net_device *bond_dev) bond_alb_deinit_slave(bond, slave); } + bond_compute_features(bond); + /* now that the slave is detached, unlock and perform * all the undo steps that should not be called from * within a lock. @@ -3588,6 +3632,7 @@ static int bond_master_netdev_event(unsigned long event, struct net_device *bond static int bond_slave_netdev_event(unsigned long event, struct net_device *slave_dev) { struct net_device *bond_dev = slave_dev->master; + struct bonding *bond = bond_dev->priv; switch (event) { case NETDEV_UNREGISTER: @@ -3626,6 +3671,9 @@ static int bond_slave_netdev_event(unsigned long event, struct net_device *slave * TODO: handle changing the primary's name */ break; + case NETDEV_FEAT_CHANGE: + bond_compute_features(bond); + break; default: break; } @@ -4526,6 +4574,11 @@ static inline void bond_set_mode_ops(struct bonding *bond, int mode) } } +static struct ethtool_ops bond_ethtool_ops = { + .get_tx_csum = ethtool_op_get_tx_csum, + .get_sg = ethtool_op_get_sg, +}; + /* * Does not allocate but creates a /proc entry. * Allowed to fail. @@ -4555,6 +4608,7 @@ static int __init bond_init(struct net_device *bond_dev, struct bond_params *par bond_dev->stop = bond_close; bond_dev->get_stats = bond_get_stats; bond_dev->do_ioctl = bond_do_ioctl; + bond_dev->ethtool_ops = &bond_ethtool_ops; bond_dev->set_multicast_list = bond_set_multicast_list; bond_dev->change_mtu = bond_change_mtu; bond_dev->set_mac_address = bond_set_mac_address; @@ -4591,6 +4645,8 @@ static int __init bond_init(struct net_device *bond_dev, struct bond_params *par NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER); + bond->bond_features = bond_dev->features; + #ifdef CONFIG_PROC_FS bond_create_proc_entry(bond); #endif diff --git a/drivers/net/bonding/bonding.h b/drivers/net/bonding/bonding.h index d27f377..3881969 100644 --- a/drivers/net/bonding/bonding.h +++ b/drivers/net/bonding/bonding.h @@ -211,6 +211,9 @@ struct bonding { struct bond_params params; struct list_head vlan_list; struct vlan_group *vlgrp; + /* the features the bonding device supports, independently + * of any slaves */ + int bond_features; }; /** -- cgit v0.10.2 From 815f62bf742718458ba822a7e1f51f285eb997f2 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Wed, 24 Aug 2005 18:06:36 +0100 Subject: [PATCH] SMP rewrite of mkiss Rewrite the mkiss driver to make it SMP-proof following the example of 6pack.c. Signed-off-by: Ralf Baechle DL5RB Signed-off-by: Jeff Garzik diff --git a/drivers/net/hamradio/Kconfig b/drivers/net/hamradio/Kconfig index 0cd5430..de087cd 100644 --- a/drivers/net/hamradio/Kconfig +++ b/drivers/net/hamradio/Kconfig @@ -1,6 +1,6 @@ config MKISS tristate "Serial port KISS driver" - depends on AX25 && BROKEN_ON_SMP + depends on AX25 ---help--- KISS is a protocol used for the exchange of data between a computer and a Terminal Node Controller (a small embedded system commonly diff --git a/drivers/net/hamradio/mkiss.c b/drivers/net/hamradio/mkiss.c index e94952e..63b1a2b 100644 --- a/drivers/net/hamradio/mkiss.c +++ b/drivers/net/hamradio/mkiss.c @@ -1,30 +1,19 @@ /* - * MKISS Driver + * This program is free software; you can distribute it and/or modify it + * under the terms of the GNU General Public License (Version 2) as + * published by the Free Software Foundation. * - * This module: - * This module is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. * - * This module implements the AX.25 protocol for kernel-based - * devices like TTYs. It interfaces between a raw TTY, and the - * kernel's AX.25 protocol layers, just like slip.c. - * AX.25 needs to be separated from slip.c while slip.c is no - * longer a static kernel device since it is a module. - * This method clears the way to implement other kiss protocols - * like mkiss smack g8bpq ..... so far only mkiss is implemented. + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. * - * Hans Alblas - * - * History - * Jonathan (G4KLX) Fixed to match Linux networking changes - 2.1.15. - * Matthias (DG2FEF) Added support for FlexNet CRC (on special request) - * Fixed bug in ax25_close(): dev_lock_wait() was - * called twice, causing a deadlock. - * Jeroen (PE1RXQ) Removed old MKISS_MAGIC stuff and calls to - * MOD_*_USE_COUNT - * Remove cli() and fix rtnl lock usage. + * Copyright (C) Hans Alblas PE1AYX + * Copyright (C) 2004, 05 Ralf Baechle DL5RB */ #include @@ -50,174 +39,296 @@ #include -#include "mkiss.h" - #ifdef CONFIG_INET #include #include #endif -static char banner[] __initdata = KERN_INFO "mkiss: AX.25 Multikiss, Hans Albas PE1AYX\n"; - -typedef struct ax25_ctrl { - struct ax_disp ctrl; /* */ - struct net_device dev; /* the device */ -} ax25_ctrl_t; - -static ax25_ctrl_t **ax25_ctrls; - -int ax25_maxdev = AX25_MAXDEV; /* Can be overridden with insmod! */ - -static struct tty_ldisc ax_ldisc; - -static int ax25_init(struct net_device *); -static int kiss_esc(unsigned char *, unsigned char *, int); -static int kiss_esc_crc(unsigned char *, unsigned char *, unsigned short, int); -static void kiss_unesc(struct ax_disp *, unsigned char); +#define AX_MTU 236 + +/* SLIP/KISS protocol characters. */ +#define END 0300 /* indicates end of frame */ +#define ESC 0333 /* indicates byte stuffing */ +#define ESC_END 0334 /* ESC ESC_END means END 'data' */ +#define ESC_ESC 0335 /* ESC ESC_ESC means ESC 'data' */ + +struct mkiss { + struct tty_struct *tty; /* ptr to TTY structure */ + struct net_device *dev; /* easy for intr handling */ + + /* These are pointers to the malloc()ed frame buffers. */ + spinlock_t buflock;/* lock for rbuf and xbuf */ + unsigned char *rbuff; /* receiver buffer */ + int rcount; /* received chars counter */ + unsigned char *xbuff; /* transmitter buffer */ + unsigned char *xhead; /* pointer to next byte to XMIT */ + int xleft; /* bytes left in XMIT queue */ + + struct net_device_stats stats; + + /* Detailed SLIP statistics. */ + int mtu; /* Our mtu (to spot changes!) */ + int buffsize; /* Max buffers sizes */ + + unsigned long flags; /* Flag values/ mode etc */ + /* long req'd: used by set_bit --RR */ +#define AXF_INUSE 0 /* Channel in use */ +#define AXF_ESCAPE 1 /* ESC received */ +#define AXF_ERROR 2 /* Parity, etc. error */ +#define AXF_KEEPTEST 3 /* Keepalive test flag */ +#define AXF_OUTWAIT 4 /* is outpacket was flag */ + + int mode; + int crcmode; /* MW: for FlexNet, SMACK etc. */ +#define CRC_MODE_NONE 0 +#define CRC_MODE_FLEX 1 +#define CRC_MODE_SMACK 2 + + atomic_t refcnt; + struct semaphore dead_sem; +}; /*---------------------------------------------------------------------------*/ -static const unsigned short Crc_flex_table[] = { - 0x0f87, 0x1e0e, 0x2c95, 0x3d1c, 0x49a3, 0x582a, 0x6ab1, 0x7b38, - 0x83cf, 0x9246, 0xa0dd, 0xb154, 0xc5eb, 0xd462, 0xe6f9, 0xf770, - 0x1f06, 0x0e8f, 0x3c14, 0x2d9d, 0x5922, 0x48ab, 0x7a30, 0x6bb9, - 0x934e, 0x82c7, 0xb05c, 0xa1d5, 0xd56a, 0xc4e3, 0xf678, 0xe7f1, - 0x2e85, 0x3f0c, 0x0d97, 0x1c1e, 0x68a1, 0x7928, 0x4bb3, 0x5a3a, - 0xa2cd, 0xb344, 0x81df, 0x9056, 0xe4e9, 0xf560, 0xc7fb, 0xd672, - 0x3e04, 0x2f8d, 0x1d16, 0x0c9f, 0x7820, 0x69a9, 0x5b32, 0x4abb, - 0xb24c, 0xa3c5, 0x915e, 0x80d7, 0xf468, 0xe5e1, 0xd77a, 0xc6f3, - 0x4d83, 0x5c0a, 0x6e91, 0x7f18, 0x0ba7, 0x1a2e, 0x28b5, 0x393c, - 0xc1cb, 0xd042, 0xe2d9, 0xf350, 0x87ef, 0x9666, 0xa4fd, 0xb574, - 0x5d02, 0x4c8b, 0x7e10, 0x6f99, 0x1b26, 0x0aaf, 0x3834, 0x29bd, - 0xd14a, 0xc0c3, 0xf258, 0xe3d1, 0x976e, 0x86e7, 0xb47c, 0xa5f5, - 0x6c81, 0x7d08, 0x4f93, 0x5e1a, 0x2aa5, 0x3b2c, 0x09b7, 0x183e, - 0xe0c9, 0xf140, 0xc3db, 0xd252, 0xa6ed, 0xb764, 0x85ff, 0x9476, - 0x7c00, 0x6d89, 0x5f12, 0x4e9b, 0x3a24, 0x2bad, 0x1936, 0x08bf, - 0xf048, 0xe1c1, 0xd35a, 0xc2d3, 0xb66c, 0xa7e5, 0x957e, 0x84f7, - 0x8b8f, 0x9a06, 0xa89d, 0xb914, 0xcdab, 0xdc22, 0xeeb9, 0xff30, - 0x07c7, 0x164e, 0x24d5, 0x355c, 0x41e3, 0x506a, 0x62f1, 0x7378, - 0x9b0e, 0x8a87, 0xb81c, 0xa995, 0xdd2a, 0xcca3, 0xfe38, 0xefb1, - 0x1746, 0x06cf, 0x3454, 0x25dd, 0x5162, 0x40eb, 0x7270, 0x63f9, - 0xaa8d, 0xbb04, 0x899f, 0x9816, 0xeca9, 0xfd20, 0xcfbb, 0xde32, - 0x26c5, 0x374c, 0x05d7, 0x145e, 0x60e1, 0x7168, 0x43f3, 0x527a, - 0xba0c, 0xab85, 0x991e, 0x8897, 0xfc28, 0xeda1, 0xdf3a, 0xceb3, - 0x3644, 0x27cd, 0x1556, 0x04df, 0x7060, 0x61e9, 0x5372, 0x42fb, - 0xc98b, 0xd802, 0xea99, 0xfb10, 0x8faf, 0x9e26, 0xacbd, 0xbd34, - 0x45c3, 0x544a, 0x66d1, 0x7758, 0x03e7, 0x126e, 0x20f5, 0x317c, - 0xd90a, 0xc883, 0xfa18, 0xeb91, 0x9f2e, 0x8ea7, 0xbc3c, 0xadb5, - 0x5542, 0x44cb, 0x7650, 0x67d9, 0x1366, 0x02ef, 0x3074, 0x21fd, - 0xe889, 0xf900, 0xcb9b, 0xda12, 0xaead, 0xbf24, 0x8dbf, 0x9c36, - 0x64c1, 0x7548, 0x47d3, 0x565a, 0x22e5, 0x336c, 0x01f7, 0x107e, - 0xf808, 0xe981, 0xdb1a, 0xca93, 0xbe2c, 0xafa5, 0x9d3e, 0x8cb7, - 0x7440, 0x65c9, 0x5752, 0x46db, 0x3264, 0x23ed, 0x1176, 0x00ff +static const unsigned short crc_flex_table[] = { + 0x0f87, 0x1e0e, 0x2c95, 0x3d1c, 0x49a3, 0x582a, 0x6ab1, 0x7b38, + 0x83cf, 0x9246, 0xa0dd, 0xb154, 0xc5eb, 0xd462, 0xe6f9, 0xf770, + 0x1f06, 0x0e8f, 0x3c14, 0x2d9d, 0x5922, 0x48ab, 0x7a30, 0x6bb9, + 0x934e, 0x82c7, 0xb05c, 0xa1d5, 0xd56a, 0xc4e3, 0xf678, 0xe7f1, + 0x2e85, 0x3f0c, 0x0d97, 0x1c1e, 0x68a1, 0x7928, 0x4bb3, 0x5a3a, + 0xa2cd, 0xb344, 0x81df, 0x9056, 0xe4e9, 0xf560, 0xc7fb, 0xd672, + 0x3e04, 0x2f8d, 0x1d16, 0x0c9f, 0x7820, 0x69a9, 0x5b32, 0x4abb, + 0xb24c, 0xa3c5, 0x915e, 0x80d7, 0xf468, 0xe5e1, 0xd77a, 0xc6f3, + 0x4d83, 0x5c0a, 0x6e91, 0x7f18, 0x0ba7, 0x1a2e, 0x28b5, 0x393c, + 0xc1cb, 0xd042, 0xe2d9, 0xf350, 0x87ef, 0x9666, 0xa4fd, 0xb574, + 0x5d02, 0x4c8b, 0x7e10, 0x6f99, 0x1b26, 0x0aaf, 0x3834, 0x29bd, + 0xd14a, 0xc0c3, 0xf258, 0xe3d1, 0x976e, 0x86e7, 0xb47c, 0xa5f5, + 0x6c81, 0x7d08, 0x4f93, 0x5e1a, 0x2aa5, 0x3b2c, 0x09b7, 0x183e, + 0xe0c9, 0xf140, 0xc3db, 0xd252, 0xa6ed, 0xb764, 0x85ff, 0x9476, + 0x7c00, 0x6d89, 0x5f12, 0x4e9b, 0x3a24, 0x2bad, 0x1936, 0x08bf, + 0xf048, 0xe1c1, 0xd35a, 0xc2d3, 0xb66c, 0xa7e5, 0x957e, 0x84f7, + 0x8b8f, 0x9a06, 0xa89d, 0xb914, 0xcdab, 0xdc22, 0xeeb9, 0xff30, + 0x07c7, 0x164e, 0x24d5, 0x355c, 0x41e3, 0x506a, 0x62f1, 0x7378, + 0x9b0e, 0x8a87, 0xb81c, 0xa995, 0xdd2a, 0xcca3, 0xfe38, 0xefb1, + 0x1746, 0x06cf, 0x3454, 0x25dd, 0x5162, 0x40eb, 0x7270, 0x63f9, + 0xaa8d, 0xbb04, 0x899f, 0x9816, 0xeca9, 0xfd20, 0xcfbb, 0xde32, + 0x26c5, 0x374c, 0x05d7, 0x145e, 0x60e1, 0x7168, 0x43f3, 0x527a, + 0xba0c, 0xab85, 0x991e, 0x8897, 0xfc28, 0xeda1, 0xdf3a, 0xceb3, + 0x3644, 0x27cd, 0x1556, 0x04df, 0x7060, 0x61e9, 0x5372, 0x42fb, + 0xc98b, 0xd802, 0xea99, 0xfb10, 0x8faf, 0x9e26, 0xacbd, 0xbd34, + 0x45c3, 0x544a, 0x66d1, 0x7758, 0x03e7, 0x126e, 0x20f5, 0x317c, + 0xd90a, 0xc883, 0xfa18, 0xeb91, 0x9f2e, 0x8ea7, 0xbc3c, 0xadb5, + 0x5542, 0x44cb, 0x7650, 0x67d9, 0x1366, 0x02ef, 0x3074, 0x21fd, + 0xe889, 0xf900, 0xcb9b, 0xda12, 0xaead, 0xbf24, 0x8dbf, 0x9c36, + 0x64c1, 0x7548, 0x47d3, 0x565a, 0x22e5, 0x336c, 0x01f7, 0x107e, + 0xf808, 0xe981, 0xdb1a, 0xca93, 0xbe2c, 0xafa5, 0x9d3e, 0x8cb7, + 0x7440, 0x65c9, 0x5752, 0x46db, 0x3264, 0x23ed, 0x1176, 0x00ff }; -/*---------------------------------------------------------------------------*/ - static unsigned short calc_crc_flex(unsigned char *cp, int size) { - unsigned short crc = 0xffff; - - while (size--) - crc = (crc << 8) ^ Crc_flex_table[((crc >> 8) ^ *cp++) & 0xff]; + unsigned short crc = 0xffff; - return crc; -} + while (size--) + crc = (crc << 8) ^ crc_flex_table[((crc >> 8) ^ *cp++) & 0xff]; -/*---------------------------------------------------------------------------*/ + return crc; +} static int check_crc_flex(unsigned char *cp, int size) { - unsigned short crc = 0xffff; + unsigned short crc = 0xffff; - if (size < 3) - return -1; + if (size < 3) + return -1; - while (size--) - crc = (crc << 8) ^ Crc_flex_table[((crc >> 8) ^ *cp++) & 0xff]; + while (size--) + crc = (crc << 8) ^ crc_flex_table[((crc >> 8) ^ *cp++) & 0xff]; - if ((crc & 0xffff) != 0x7070) - return -1; + if ((crc & 0xffff) != 0x7070) + return -1; - return 0; + return 0; } -/*---------------------------------------------------------------------------*/ +/* + * Standard encapsulation + */ -/* Find a free channel, and link in this `tty' line. */ -static inline struct ax_disp *ax_alloc(void) +static int kiss_esc(unsigned char *s, unsigned char *d, int len) { - ax25_ctrl_t *axp=NULL; - int i; + unsigned char *ptr = d; + unsigned char c; - for (i = 0; i < ax25_maxdev; i++) { - axp = ax25_ctrls[i]; + /* + * Send an initial END character to flush out any data that may have + * accumulated in the receiver due to line noise. + */ - /* Not allocated ? */ - if (axp == NULL) - break; + *ptr++ = END; - /* Not in use ? */ - if (!test_and_set_bit(AXF_INUSE, &axp->ctrl.flags)) + while (len-- > 0) { + switch (c = *s++) { + case END: + *ptr++ = ESC; + *ptr++ = ESC_END; break; + case ESC: + *ptr++ = ESC; + *ptr++ = ESC_ESC; + break; + default: + *ptr++ = c; + break; + } } - /* Sorry, too many, all slots in use */ - if (i >= ax25_maxdev) - return NULL; + *ptr++ = END; + + return ptr - d; +} + +/* + * MW: + * OK its ugly, but tell me a better solution without copying the + * packet to a temporary buffer :-) + */ +static int kiss_esc_crc(unsigned char *s, unsigned char *d, unsigned short crc, + int len) +{ + unsigned char *ptr = d; + unsigned char c=0; + + *ptr++ = END; + while (len > 0) { + if (len > 2) + c = *s++; + else if (len > 1) + c = crc >> 8; + else if (len > 0) + c = crc & 0xff; + + len--; - /* If no channels are available, allocate one */ - if (axp == NULL && (ax25_ctrls[i] = kmalloc(sizeof(ax25_ctrl_t), GFP_KERNEL)) != NULL) { - axp = ax25_ctrls[i]; + switch (c) { + case END: + *ptr++ = ESC; + *ptr++ = ESC_END; + break; + case ESC: + *ptr++ = ESC; + *ptr++ = ESC_ESC; + break; + default: + *ptr++ = c; + break; + } } - memset(axp, 0, sizeof(ax25_ctrl_t)); - - /* Initialize channel control data */ - set_bit(AXF_INUSE, &axp->ctrl.flags); - sprintf(axp->dev.name, "ax%d", i++); - axp->ctrl.tty = NULL; - axp->dev.base_addr = i; - axp->dev.priv = (void *)&axp->ctrl; - axp->dev.next = NULL; - axp->dev.init = ax25_init; - - if (axp != NULL) { - /* - * register device so that it can be ifconfig'ed - * ax25_init() will be called as a side-effect - * SIDE-EFFECT WARNING: ax25_init() CLEARS axp->ctrl ! - */ - if (register_netdev(&axp->dev) == 0) { - /* (Re-)Set the INUSE bit. Very Important! */ - set_bit(AXF_INUSE, &axp->ctrl.flags); - axp->ctrl.dev = &axp->dev; - axp->dev.priv = (void *) &axp->ctrl; - - return &axp->ctrl; - } else { - clear_bit(AXF_INUSE,&axp->ctrl.flags); - printk(KERN_ERR "mkiss: ax_alloc() - register_netdev() failure.\n"); + *ptr++ = END; + + return ptr - d; +} + +/* Send one completely decapsulated AX.25 packet to the AX.25 layer. */ +static void ax_bump(struct mkiss *ax) +{ + struct sk_buff *skb; + int count; + + spin_lock_bh(&ax->buflock); + if (ax->rbuff[0] > 0x0f) { + if (ax->rbuff[0] & 0x20) { + ax->crcmode = CRC_MODE_FLEX; + if (check_crc_flex(ax->rbuff, ax->rcount) < 0) { + ax->stats.rx_errors++; + return; + } + ax->rcount -= 2; + /* dl9sau bugfix: the trailling two bytes flexnet crc + * will not be passed to the kernel. thus we have + * to correct the kissparm signature, because it + * indicates a crc but there's none + */ + *ax->rbuff &= ~0x20; } + } + spin_unlock_bh(&ax->buflock); + + count = ax->rcount; + + if ((skb = dev_alloc_skb(count)) == NULL) { + printk(KERN_ERR "mkiss: %s: memory squeeze, dropping packet.\n", + ax->dev->name); + ax->stats.rx_dropped++; + return; } - return NULL; + spin_lock_bh(&ax->buflock); + memcpy(skb_put(skb,count), ax->rbuff, count); + spin_unlock_bh(&ax->buflock); + skb->protocol = ax25_type_trans(skb, ax->dev); + netif_rx(skb); + ax->dev->last_rx = jiffies; + ax->stats.rx_packets++; + ax->stats.rx_bytes += count; } -/* Free an AX25 channel. */ -static inline void ax_free(struct ax_disp *ax) +static void kiss_unesc(struct mkiss *ax, unsigned char s) { - /* Free all AX25 frame buffers. */ - if (ax->rbuff) - kfree(ax->rbuff); - ax->rbuff = NULL; - if (ax->xbuff) - kfree(ax->xbuff); - ax->xbuff = NULL; - if (!test_and_clear_bit(AXF_INUSE, &ax->flags)) - printk(KERN_ERR "mkiss: %s: ax_free for already free unit.\n", ax->dev->name); + switch (s) { + case END: + /* drop keeptest bit = VSV */ + if (test_bit(AXF_KEEPTEST, &ax->flags)) + clear_bit(AXF_KEEPTEST, &ax->flags); + + if (!test_and_clear_bit(AXF_ERROR, &ax->flags) && (ax->rcount > 2)) + ax_bump(ax); + + clear_bit(AXF_ESCAPE, &ax->flags); + ax->rcount = 0; + return; + + case ESC: + set_bit(AXF_ESCAPE, &ax->flags); + return; + case ESC_ESC: + if (test_and_clear_bit(AXF_ESCAPE, &ax->flags)) + s = ESC; + break; + case ESC_END: + if (test_and_clear_bit(AXF_ESCAPE, &ax->flags)) + s = END; + break; + } + + spin_lock_bh(&ax->buflock); + if (!test_bit(AXF_ERROR, &ax->flags)) { + if (ax->rcount < ax->buffsize) { + ax->rbuff[ax->rcount++] = s; + spin_unlock_bh(&ax->buflock); + return; + } + + ax->stats.rx_over_errors++; + set_bit(AXF_ERROR, &ax->flags); + } + spin_unlock_bh(&ax->buflock); +} + +static int ax_set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr_ax25 *sa = addr; + + spin_lock_irq(&dev->xmit_lock); + memcpy(dev->dev_addr, &sa->sax25_call, AX25_ADDR_LEN); + spin_unlock_irq(&dev->xmit_lock); + + return 0; } -static void ax_changedmtu(struct ax_disp *ax) +/*---------------------------------------------------------------------------*/ + +static void ax_changedmtu(struct mkiss *ax) { struct net_device *dev = ax->dev; unsigned char *xbuff, *rbuff, *oxbuff, *orbuff; @@ -237,7 +348,8 @@ static void ax_changedmtu(struct ax_disp *ax) rbuff = kmalloc(len + 4, GFP_ATOMIC); if (xbuff == NULL || rbuff == NULL) { - printk(KERN_ERR "mkiss: %s: unable to grow ax25 buffers, MTU change cancelled.\n", + printk(KERN_ERR "mkiss: %s: unable to grow ax25 buffers, " + "MTU change cancelled.\n", ax->dev->name); dev->mtu = ax->mtu; if (xbuff != NULL) @@ -259,7 +371,7 @@ static void ax_changedmtu(struct ax_disp *ax) memcpy(ax->xbuff, ax->xhead, ax->xleft); } else { ax->xleft = 0; - ax->tx_dropped++; + ax->stats.tx_dropped++; } } @@ -270,7 +382,7 @@ static void ax_changedmtu(struct ax_disp *ax) memcpy(ax->rbuff, orbuff, ax->rcount); } else { ax->rcount = 0; - ax->rx_over_errors++; + ax->stats.rx_over_errors++; set_bit(AXF_ERROR, &ax->flags); } } @@ -280,72 +392,14 @@ static void ax_changedmtu(struct ax_disp *ax) spin_unlock_bh(&ax->buflock); - if (oxbuff != NULL) - kfree(oxbuff); - if (orbuff != NULL) - kfree(orbuff); -} - - -/* Set the "sending" flag. This must be atomic. */ -static inline void ax_lock(struct ax_disp *ax) -{ - netif_stop_queue(ax->dev); -} - - -/* Clear the "sending" flag. This must be atomic. */ -static inline void ax_unlock(struct ax_disp *ax) -{ - netif_start_queue(ax->dev); -} - -/* Send one completely decapsulated AX.25 packet to the AX.25 layer. */ -static void ax_bump(struct ax_disp *ax) -{ - struct sk_buff *skb; - int count; - - spin_lock_bh(&ax->buflock); - if (ax->rbuff[0] > 0x0f) { - if (ax->rbuff[0] & 0x20) { - ax->crcmode = CRC_MODE_FLEX; - if (check_crc_flex(ax->rbuff, ax->rcount) < 0) { - ax->rx_errors++; - return; - } - ax->rcount -= 2; - /* dl9sau bugfix: the trailling two bytes flexnet crc - * will not be passed to the kernel. thus we have - * to correct the kissparm signature, because it - * indicates a crc but there's none - */ - *ax->rbuff &= ~0x20; - } - } - spin_unlock_bh(&ax->buflock); - - count = ax->rcount; - - if ((skb = dev_alloc_skb(count)) == NULL) { - printk(KERN_ERR "mkiss: %s: memory squeeze, dropping packet.\n", ax->dev->name); - ax->rx_dropped++; - return; - } - - spin_lock_bh(&ax->buflock); - memcpy(skb_put(skb,count), ax->rbuff, count); - spin_unlock_bh(&ax->buflock); - skb->protocol = ax25_type_trans(skb, ax->dev); - netif_rx(skb); - ax->dev->last_rx = jiffies; - ax->rx_packets++; - ax->rx_bytes+=count; + kfree(oxbuff); + kfree(orbuff); } /* Encapsulate one AX.25 packet and stuff into a TTY queue. */ -static void ax_encaps(struct ax_disp *ax, unsigned char *icp, int len) +static void ax_encaps(struct net_device *dev, unsigned char *icp, int len) { + struct mkiss *ax = netdev_priv(dev); unsigned char *p; int actual, count; @@ -355,8 +409,8 @@ static void ax_encaps(struct ax_disp *ax, unsigned char *icp, int len) if (len > ax->mtu) { /* Sigh, shouldn't occur BUT ... */ len = ax->mtu; printk(KERN_ERR "mkiss: %s: truncating oversized transmit packet!\n", ax->dev->name); - ax->tx_dropped++; - ax_unlock(ax); + ax->stats.tx_dropped++; + netif_start_queue(dev); return; } @@ -377,10 +431,11 @@ static void ax_encaps(struct ax_disp *ax, unsigned char *icp, int len) break; } - ax->tty->flags |= (1 << TTY_DO_WRITE_WAKEUP); + set_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags); actual = ax->tty->driver->write(ax->tty, ax->xbuff, count); - ax->tx_packets++; - ax->tx_bytes+=actual; + ax->stats.tx_packets++; + ax->stats.tx_bytes += actual; + ax->dev->trans_start = jiffies; ax->xleft = count - actual; ax->xhead = ax->xbuff + actual; @@ -388,37 +443,10 @@ static void ax_encaps(struct ax_disp *ax, unsigned char *icp, int len) spin_unlock_bh(&ax->buflock); } -/* - * Called by the driver when there's room for more data. If we have - * more packets to send, we send them here. - */ -static void ax25_write_wakeup(struct tty_struct *tty) -{ - int actual; - struct ax_disp *ax = (struct ax_disp *) tty->disc_data; - - /* First make sure we're connected. */ - if (ax == NULL || ax->magic != AX25_MAGIC || !netif_running(ax->dev)) - return; - if (ax->xleft <= 0) { - /* Now serial buffer is almost free & we can start - * transmission of another packet - */ - tty->flags &= ~(1 << TTY_DO_WRITE_WAKEUP); - - netif_wake_queue(ax->dev); - return; - } - - actual = tty->driver->write(tty, ax->xhead, ax->xleft); - ax->xleft -= actual; - ax->xhead += actual; -} - /* Encapsulate an AX.25 packet and kick it into a TTY queue. */ static int ax_xmit(struct sk_buff *skb, struct net_device *dev) { - struct ax_disp *ax = netdev_priv(dev); + struct mkiss *ax = netdev_priv(dev); if (!netif_running(dev)) { printk(KERN_ERR "mkiss: %s: xmit call when iface is down\n", dev->name); @@ -440,20 +468,30 @@ static int ax_xmit(struct sk_buff *skb, struct net_device *dev) "bad line quality" : "driver error"); ax->xleft = 0; - ax->tty->flags &= ~(1 << TTY_DO_WRITE_WAKEUP); - ax_unlock(ax); + clear_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags); + netif_start_queue(dev); } /* We were not busy, so we are now... :-) */ if (skb != NULL) { - ax_lock(ax); - ax_encaps(ax, skb->data, skb->len); + netif_stop_queue(dev); + ax_encaps(dev, skb->data, skb->len); kfree_skb(skb); } return 0; } +static int ax_open_dev(struct net_device *dev) +{ + struct mkiss *ax = netdev_priv(dev); + + if (ax->tty == NULL) + return -ENODEV; + + return 0; +} + #if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE) /* Return the frame type ID */ @@ -482,7 +520,7 @@ static int ax_rebuild_header(struct sk_buff *skb) /* Open the low-level part of the AX25 channel. Easy! */ static int ax_open(struct net_device *dev) { - struct ax_disp *ax = netdev_priv(dev); + struct mkiss *ax = netdev_priv(dev); unsigned long len; if (ax->tty == NULL) @@ -519,7 +557,6 @@ static int ax_open(struct net_device *dev) spin_lock_init(&ax->buflock); - netif_start_queue(dev); return 0; noxbuff: @@ -533,68 +570,100 @@ norbuff: /* Close the low-level part of the AX25 channel. Easy! */ static int ax_close(struct net_device *dev) { - struct ax_disp *ax = netdev_priv(dev); + struct mkiss *ax = netdev_priv(dev); - if (ax->tty == NULL) - return -EBUSY; - - ax->tty->flags &= ~(1 << TTY_DO_WRITE_WAKEUP); + if (ax->tty) + clear_bit(TTY_DO_WRITE_WAKEUP, &ax->tty->flags); netif_stop_queue(dev); return 0; } -static int ax25_receive_room(struct tty_struct *tty) +static struct net_device_stats *ax_get_stats(struct net_device *dev) { - return 65536; /* We can handle an infinite amount of data. :-) */ + struct mkiss *ax = netdev_priv(dev); + + return &ax->stats; +} + +static void ax_setup(struct net_device *dev) +{ + static char ax25_bcast[AX25_ADDR_LEN] = + {'Q'<<1,'S'<<1,'T'<<1,' '<<1,' '<<1,' '<<1,'0'<<1}; + static char ax25_test[AX25_ADDR_LEN] = + {'L'<<1,'I'<<1,'N'<<1,'U'<<1,'X'<<1,' '<<1,'1'<<1}; + + /* Finish setting up the DEVICE info. */ + dev->mtu = AX_MTU; + dev->hard_start_xmit = ax_xmit; + dev->open = ax_open_dev; + dev->stop = ax_close; + dev->get_stats = ax_get_stats; + dev->set_mac_address = ax_set_mac_address; + dev->hard_header_len = 0; + dev->addr_len = 0; + dev->type = ARPHRD_AX25; + dev->tx_queue_len = 10; + dev->hard_header = ax_header; + dev->rebuild_header = ax_rebuild_header; + + memcpy(dev->broadcast, ax25_bcast, AX25_ADDR_LEN); + memcpy(dev->dev_addr, ax25_test, AX25_ADDR_LEN); + + dev->flags = IFF_BROADCAST | IFF_MULTICAST; } /* - * Handle the 'receiver data ready' interrupt. - * This function is called by the 'tty_io' module in the kernel when - * a block of data has been received, which can now be decapsulated - * and sent on to the AX.25 layer for further processing. + * We have a potential race on dereferencing tty->disc_data, because the tty + * layer provides no locking at all - thus one cpu could be running + * sixpack_receive_buf while another calls sixpack_close, which zeroes + * tty->disc_data and frees the memory that sixpack_receive_buf is using. The + * best way to fix this is to use a rwlock in the tty struct, but for now we + * use a single global rwlock for all ttys in ppp line discipline. */ -static void ax25_receive_buf(struct tty_struct *tty, const unsigned char *cp, char *fp, int count) +static rwlock_t disc_data_lock = RW_LOCK_UNLOCKED; + +static struct mkiss *mkiss_get(struct tty_struct *tty) { - struct ax_disp *ax = (struct ax_disp *) tty->disc_data; + struct mkiss *ax; - if (ax == NULL || ax->magic != AX25_MAGIC || !netif_running(ax->dev)) - return; + read_lock(&disc_data_lock); + ax = tty->disc_data; + if (ax) + atomic_inc(&ax->refcnt); + read_unlock(&disc_data_lock); - /* - * Argh! mtu change time! - costs us the packet part received - * at the change - */ - if (ax->mtu != ax->dev->mtu + 73) - ax_changedmtu(ax); - - /* Read the characters out of the buffer */ - while (count--) { - if (fp != NULL && *fp++) { - if (!test_and_set_bit(AXF_ERROR, &ax->flags)) - ax->rx_errors++; - cp++; - continue; - } + return ax; +} - kiss_unesc(ax, *cp++); - } +static void mkiss_put(struct mkiss *ax) +{ + if (atomic_dec_and_test(&ax->refcnt)) + up(&ax->dead_sem); } -static int ax25_open(struct tty_struct *tty) +static int mkiss_open(struct tty_struct *tty) { - struct ax_disp *ax = (struct ax_disp *) tty->disc_data; + struct net_device *dev; + struct mkiss *ax; int err; - /* First make sure we're not already connected. */ - if (ax && ax->magic == AX25_MAGIC) - return -EEXIST; + if (!capable(CAP_NET_ADMIN)) + return -EPERM; - /* OK. Find a free AX25 channel to use. */ - if ((ax = ax_alloc()) == NULL) - return -ENFILE; + dev = alloc_netdev(sizeof(struct mkiss), "ax%d", ax_setup); + if (!dev) { + err = -ENOMEM; + goto out; + } + + ax = netdev_priv(dev); + ax->dev = dev; + + spin_lock_init(&ax->buflock); + atomic_set(&ax->refcnt, 1); + init_MUTEX_LOCKED(&ax->dead_sem); ax->tty = tty; tty->disc_data = ax; @@ -603,283 +672,212 @@ static int ax25_open(struct tty_struct *tty) tty->driver->flush_buffer(tty); /* Restore default settings */ - ax->dev->type = ARPHRD_AX25; + dev->type = ARPHRD_AX25; /* Perform the low-level AX25 initialization. */ - if ((err = ax_open(ax->dev))) - return err; + if ((err = ax_open(ax->dev))) { + goto out_free_netdev; + } - /* Done. We have linked the TTY line to a channel. */ - return ax->dev->base_addr; -} + if (register_netdev(dev)) + goto out_free_buffers; -static void ax25_close(struct tty_struct *tty) -{ - struct ax_disp *ax = (struct ax_disp *) tty->disc_data; + netif_start_queue(dev); - /* First make sure we're connected. */ - if (ax == NULL || ax->magic != AX25_MAGIC) - return; + /* Done. We have linked the TTY line to a channel. */ + return 0; - unregister_netdev(ax->dev); +out_free_buffers: + kfree(ax->rbuff); + kfree(ax->xbuff); - tty->disc_data = NULL; - ax->tty = NULL; +out_free_netdev: + free_netdev(dev); - ax_free(ax); +out: + return err; } - -static struct net_device_stats *ax_get_stats(struct net_device *dev) +static void mkiss_close(struct tty_struct *tty) { - static struct net_device_stats stats; - struct ax_disp *ax = netdev_priv(dev); - - memset(&stats, 0, sizeof(struct net_device_stats)); - - stats.rx_packets = ax->rx_packets; - stats.tx_packets = ax->tx_packets; - stats.rx_bytes = ax->rx_bytes; - stats.tx_bytes = ax->tx_bytes; - stats.rx_dropped = ax->rx_dropped; - stats.tx_dropped = ax->tx_dropped; - stats.tx_errors = ax->tx_errors; - stats.rx_errors = ax->rx_errors; - stats.rx_over_errors = ax->rx_over_errors; - - return &stats; -} + struct mkiss *ax; + write_lock(&disc_data_lock); + ax = tty->disc_data; + tty->disc_data = NULL; + write_unlock(&disc_data_lock); -/************************************************************************ - * STANDARD ENCAPSULATION * - ************************************************************************/ - -static int kiss_esc(unsigned char *s, unsigned char *d, int len) -{ - unsigned char *ptr = d; - unsigned char c; + if (ax == 0) + return; /* - * Send an initial END character to flush out any - * data that may have accumulated in the receiver - * due to line noise. + * We have now ensured that nobody can start using ap from now on, but + * we have to wait for all existing users to finish. */ + if (!atomic_dec_and_test(&ax->refcnt)) + down(&ax->dead_sem); - *ptr++ = END; - - while (len-- > 0) { - switch (c = *s++) { - case END: - *ptr++ = ESC; - *ptr++ = ESC_END; - break; - case ESC: - *ptr++ = ESC; - *ptr++ = ESC_ESC; - break; - default: - *ptr++ = c; - break; - } - } + unregister_netdev(ax->dev); - *ptr++ = END; + /* Free all AX25 frame buffers. */ + kfree(ax->rbuff); + kfree(ax->xbuff); - return ptr - d; + ax->tty = NULL; } -/* - * MW: - * OK its ugly, but tell me a better solution without copying the - * packet to a temporary buffer :-) - */ -static int kiss_esc_crc(unsigned char *s, unsigned char *d, unsigned short crc, int len) +/* Perform I/O control on an active ax25 channel. */ +static int mkiss_ioctl(struct tty_struct *tty, struct file *file, + unsigned int cmd, unsigned long arg) { - unsigned char *ptr = d; - unsigned char c=0; - - *ptr++ = END; - while (len > 0) { - if (len > 2) - c = *s++; - else if (len > 1) - c = crc >> 8; - else if (len > 0) - c = crc & 0xff; + struct mkiss *ax = mkiss_get(tty); + struct net_device *dev = ax->dev; + unsigned int tmp, err; - len--; + /* First make sure we're connected. */ + if (ax == NULL) + return -ENXIO; - switch (c) { - case END: - *ptr++ = ESC; - *ptr++ = ESC_END; - break; - case ESC: - *ptr++ = ESC; - *ptr++ = ESC_ESC; - break; - default: - *ptr++ = c; - break; + switch (cmd) { + case SIOCGIFNAME: + err = copy_to_user((void __user *) arg, ax->dev->name, + strlen(ax->dev->name) + 1) ? -EFAULT : 0; + break; + + case SIOCGIFENCAP: + err = put_user(4, (int __user *) arg); + break; + + case SIOCSIFENCAP: + if (get_user(tmp, (int __user *) arg)) { + err = -EFAULT; + break; } - } - *ptr++ = END; - return ptr - d; -} -static void kiss_unesc(struct ax_disp *ax, unsigned char s) -{ - switch (s) { - case END: - /* drop keeptest bit = VSV */ - if (test_bit(AXF_KEEPTEST, &ax->flags)) - clear_bit(AXF_KEEPTEST, &ax->flags); + ax->mode = tmp; + dev->addr_len = AX25_ADDR_LEN; + dev->hard_header_len = AX25_KISS_HEADER_LEN + + AX25_MAX_HEADER_LEN + 3; + dev->type = ARPHRD_AX25; - if (!test_and_clear_bit(AXF_ERROR, &ax->flags) && (ax->rcount > 2)) - ax_bump(ax); + err = 0; + break; - clear_bit(AXF_ESCAPE, &ax->flags); - ax->rcount = 0; - return; + case SIOCSIFHWADDR: { + char addr[AX25_ADDR_LEN]; +printk(KERN_INFO "In SIOCSIFHWADDR"); - case ESC: - set_bit(AXF_ESCAPE, &ax->flags); - return; - case ESC_ESC: - if (test_and_clear_bit(AXF_ESCAPE, &ax->flags)) - s = ESC; + if (copy_from_user(&addr, + (void __user *) arg, AX25_ADDR_LEN)) { + err = -EFAULT; break; - case ESC_END: - if (test_and_clear_bit(AXF_ESCAPE, &ax->flags)) - s = END; - break; - } - - spin_lock_bh(&ax->buflock); - if (!test_bit(AXF_ERROR, &ax->flags)) { - if (ax->rcount < ax->buffsize) { - ax->rbuff[ax->rcount++] = s; - spin_unlock_bh(&ax->buflock); - return; } - ax->rx_over_errors++; - set_bit(AXF_ERROR, &ax->flags); + spin_lock_irq(&dev->xmit_lock); + memcpy(dev->dev_addr, addr, AX25_ADDR_LEN); + spin_unlock_irq(&dev->xmit_lock); + + err = 0; + break; + } + default: + err = -ENOIOCTLCMD; } - spin_unlock_bh(&ax->buflock); -} + mkiss_put(ax); -static int ax_set_mac_address(struct net_device *dev, void __user *addr) -{ - if (copy_from_user(dev->dev_addr, addr, AX25_ADDR_LEN)) - return -EFAULT; - return 0; + return err; } -static int ax_set_dev_mac_address(struct net_device *dev, void *addr) +/* + * Handle the 'receiver data ready' interrupt. + * This function is called by the 'tty_io' module in the kernel when + * a block of data has been received, which can now be decapsulated + * and sent on to the AX.25 layer for further processing. + */ +static void mkiss_receive_buf(struct tty_struct *tty, const unsigned char *cp, + char *fp, int count) { - struct sockaddr *sa = addr; - - memcpy(dev->dev_addr, sa->sa_data, AX25_ADDR_LEN); + struct mkiss *ax = mkiss_get(tty); - return 0; -} - - -/* Perform I/O control on an active ax25 channel. */ -static int ax25_disp_ioctl(struct tty_struct *tty, void *file, int cmd, void __user *arg) -{ - struct ax_disp *ax = (struct ax_disp *) tty->disc_data; - unsigned int tmp; + if (!ax) + return; - /* First make sure we're connected. */ - if (ax == NULL || ax->magic != AX25_MAGIC) - return -EINVAL; + /* + * Argh! mtu change time! - costs us the packet part received + * at the change + */ + if (ax->mtu != ax->dev->mtu + 73) + ax_changedmtu(ax); - switch (cmd) { - case SIOCGIFNAME: - if (copy_to_user(arg, ax->dev->name, strlen(ax->dev->name) + 1)) - return -EFAULT; - return 0; - - case SIOCGIFENCAP: - return put_user(4, (int __user *)arg); - - case SIOCSIFENCAP: - if (get_user(tmp, (int __user *)arg)) - return -EFAULT; - ax->mode = tmp; - ax->dev->addr_len = AX25_ADDR_LEN; /* sizeof an AX.25 addr */ - ax->dev->hard_header_len = AX25_KISS_HEADER_LEN + AX25_MAX_HEADER_LEN + 3; - ax->dev->type = ARPHRD_AX25; - return 0; - - case SIOCSIFHWADDR: - return ax_set_mac_address(ax->dev, arg); + /* Read the characters out of the buffer */ + while (count--) { + if (fp != NULL && *fp++) { + if (!test_and_set_bit(AXF_ERROR, &ax->flags)) + ax->stats.rx_errors++; + cp++; + continue; + } - default: - return -ENOIOCTLCMD; + kiss_unesc(ax, *cp++); } + + mkiss_put(ax); + if (test_and_clear_bit(TTY_THROTTLED, &tty->flags) + && tty->driver->unthrottle) + tty->driver->unthrottle(tty); } -static int ax_open_dev(struct net_device *dev) +static int mkiss_receive_room(struct tty_struct *tty) { - struct ax_disp *ax = netdev_priv(dev); - - if (ax->tty == NULL) - return -ENODEV; - - return 0; + return 65536; /* We can handle an infinite amount of data. :-) */ } - -/* Initialize the driver. Called by network startup. */ -static int ax25_init(struct net_device *dev) +/* + * Called by the driver when there's room for more data. If we have + * more packets to send, we send them here. + */ +static void mkiss_write_wakeup(struct tty_struct *tty) { - struct ax_disp *ax = netdev_priv(dev); - - static char ax25_bcast[AX25_ADDR_LEN] = - {'Q'<<1,'S'<<1,'T'<<1,' '<<1,' '<<1,' '<<1,'0'<<1}; - static char ax25_test[AX25_ADDR_LEN] = - {'L'<<1,'I'<<1,'N'<<1,'U'<<1,'X'<<1,' '<<1,'1'<<1}; - - if (ax == NULL) /* Allocation failed ?? */ - return -ENODEV; + struct mkiss *ax = mkiss_get(tty); + int actual; - /* Set up the "AX25 Control Block". (And clear statistics) */ - memset(ax, 0, sizeof (struct ax_disp)); - ax->magic = AX25_MAGIC; - ax->dev = dev; + if (!ax) + return; - /* Finish setting up the DEVICE info. */ - dev->mtu = AX_MTU; - dev->hard_start_xmit = ax_xmit; - dev->open = ax_open_dev; - dev->stop = ax_close; - dev->get_stats = ax_get_stats; - dev->set_mac_address = ax_set_dev_mac_address; - dev->hard_header_len = 0; - dev->addr_len = 0; - dev->type = ARPHRD_AX25; - dev->tx_queue_len = 10; - dev->hard_header = ax_header; - dev->rebuild_header = ax_rebuild_header; + if (ax->xleft <= 0) { + /* Now serial buffer is almost free & we can start + * transmission of another packet + */ + clear_bit(TTY_DO_WRITE_WAKEUP, &tty->flags); - memcpy(dev->broadcast, ax25_bcast, AX25_ADDR_LEN); - memcpy(dev->dev_addr, ax25_test, AX25_ADDR_LEN); + netif_wake_queue(ax->dev); + goto out; + } - /* New-style flags. */ - dev->flags = IFF_BROADCAST | IFF_MULTICAST; + actual = tty->driver->write(tty, ax->xhead, ax->xleft); + ax->xleft -= actual; + ax->xhead += actual; - return 0; +out: + mkiss_put(ax); } +static struct tty_ldisc ax_ldisc = { + .magic = TTY_LDISC_MAGIC, + .name = "mkiss", + .open = mkiss_open, + .close = mkiss_close, + .ioctl = mkiss_ioctl, + .receive_buf = mkiss_receive_buf, + .receive_room = mkiss_receive_room, + .write_wakeup = mkiss_write_wakeup +}; -/* ******************************************************************** */ -/* * Init MKISS driver * */ -/* ******************************************************************** */ +static char banner[] __initdata = KERN_INFO \ + "mkiss: AX.25 Multikiss, Hans Albas PE1AYX\n"; +static char msg_regfail[] __initdata = KERN_ERR \ + "mkiss: can't register line discipline (err = %d)\n"; static int __init mkiss_init_driver(void) { @@ -887,64 +885,27 @@ static int __init mkiss_init_driver(void) printk(banner); - if (ax25_maxdev < 4) - ax25_maxdev = 4; /* Sanity */ + if ((status = tty_register_ldisc(N_AX25, &ax_ldisc)) != 0) + printk(msg_regfail); - if ((ax25_ctrls = kmalloc(sizeof(void *) * ax25_maxdev, GFP_KERNEL)) == NULL) { - printk(KERN_ERR "mkiss: Can't allocate ax25_ctrls[] array!\n"); - return -ENOMEM; - } - - /* Clear the pointer array, we allocate devices when we need them */ - memset(ax25_ctrls, 0, sizeof(void*) * ax25_maxdev); /* Pointers */ - - /* Fill in our line protocol discipline, and register it */ - ax_ldisc.magic = TTY_LDISC_MAGIC; - ax_ldisc.name = "mkiss"; - ax_ldisc.open = ax25_open; - ax_ldisc.close = ax25_close; - ax_ldisc.ioctl = (int (*)(struct tty_struct *, struct file *, - unsigned int, unsigned long))ax25_disp_ioctl; - ax_ldisc.receive_buf = ax25_receive_buf; - ax_ldisc.receive_room = ax25_receive_room; - ax_ldisc.write_wakeup = ax25_write_wakeup; - - if ((status = tty_register_ldisc(N_AX25, &ax_ldisc)) != 0) { - printk(KERN_ERR "mkiss: can't register line discipline (err = %d)\n", status); - kfree(ax25_ctrls); - } return status; } +static const char msg_unregfail[] __exitdata = KERN_ERR \ + "mkiss: can't unregister line discipline (err = %d)\n"; + static void __exit mkiss_exit_driver(void) { - int i; - - for (i = 0; i < ax25_maxdev; i++) { - if (ax25_ctrls[i]) { - /* - * VSV = if dev->start==0, then device - * unregistered while close proc. - */ - if (netif_running(&ax25_ctrls[i]->dev)) - unregister_netdev(&ax25_ctrls[i]->dev); - kfree(ax25_ctrls[i]); - } - } + int ret; - kfree(ax25_ctrls); - ax25_ctrls = NULL; - - if ((i = tty_unregister_ldisc(N_AX25))) - printk(KERN_ERR "mkiss: can't unregister line discipline (err = %d)\n", i); + if ((ret = tty_unregister_ldisc(N_AX25))) + printk(msg_unregfail, ret); } -MODULE_AUTHOR("Hans Albas PE1AYX "); +MODULE_AUTHOR("Ralf Baechle DL5RB "); MODULE_DESCRIPTION("KISS driver for AX.25 over TTYs"); -MODULE_PARM(ax25_maxdev, "i"); -MODULE_PARM_DESC(ax25_maxdev, "number of MKISS devices"); MODULE_LICENSE("GPL"); MODULE_ALIAS_LDISC(N_AX25); + module_init(mkiss_init_driver); module_exit(mkiss_exit_driver); - -- cgit v0.10.2 From 86f0cd505781e42000763821ec6f70127a6abaae Mon Sep 17 00:00:00 2001 From: Francois Romieu Date: Wed, 24 Aug 2005 01:14:23 +0200 Subject: [PATCH] r8169: avoid conflict between revisions 2 and 3 of the Linksys EG1032 Both revisions share the same PCI device ID and vendor ID but revision 2 of the device uses SysKonnect's chipset whereas revision 3 of the device uses Realtek's 8169 chipset. Credit goes to Christiaan Lutzer for reporting the issue and giving the actual value for the different revisions. Signed-off-by: Francois Romieu Signed-off-by: Jeff Garzik diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index 2f9b322..f0471d1 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -186,8 +186,8 @@ const static struct { static struct pci_device_id rtl8169_pci_tbl[] = { { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8169), }, { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4300), }, - { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, 0x1032), }, { PCI_DEVICE(0x16ec, 0x0116), }, + { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0024, }, {0,}, }; diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 48a43b8..d7c9851 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -79,8 +79,8 @@ static const struct pci_device_id skge_id_table[] = { { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) }, { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */ { PCI_DEVICE(PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD) }, - { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1032) }, { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064) }, + { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015, }, { 0 } }; MODULE_DEVICE_TABLE(pci, skge_id_table); -- cgit v0.10.2 From e13934563db047043ccead26412f552375cea90c Mon Sep 17 00:00:00 2001 From: Andy Fleming Date: Wed, 24 Aug 2005 18:46:21 -0500 Subject: [PATCH] PHY Layer fixup This patch adds back the code that was taken out, thus re-enabling: * The PHY Layer to initialize without crashing * Drivers to actually connect to PHYs * The entire PHY Control Layer This patch is used by the gianfar driver, and other drivers which are in development. Signed-off-by: Andy Fleming Signed-off-by: Jeff Garzik diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index 6450bd7..6a2fe35 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -12,6 +12,14 @@ config PHYLIB devices. This option provides infrastructure for managing PHY devices. +config PHYCONTROL + bool " Support for automatically handling PHY state changes" + depends on PHYLIB + help + Adds code to perform all the work for keeping PHY link + state (speed/duplex/etc) up-to-date. Also handles + interrupts. + comment "MII PHY device drivers" depends on PHYLIB diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index fb7cb38..e4116a5 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -2,8 +2,9 @@ libphy-objs := phy.o phy_device.o mdio_bus.o -obj-$(CONFIG_MARVELL_PHY) += libphy.o marvell.o -obj-$(CONFIG_DAVICOM_PHY) += libphy.o davicom.o -obj-$(CONFIG_CICADA_PHY) += libphy.o cicada.o -obj-$(CONFIG_LXT_PHY) += libphy.o lxt.o -obj-$(CONFIG_QSEMI_PHY) += libphy.o qsemi.o +obj-$(CONFIG_PHYLIB) += libphy.o +obj-$(CONFIG_MARVELL_PHY) += marvell.o +obj-$(CONFIG_DAVICOM_PHY) += davicom.o +obj-$(CONFIG_CICADA_PHY) += cicada.o +obj-$(CONFIG_LXT_PHY) += lxt.o +obj-$(CONFIG_QSEMI_PHY) += qsemi.o diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index d5a05be..41f62c0 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -38,6 +38,80 @@ #include #include +/* mdiobus_register + * + * description: Called by a bus driver to bring up all the PHYs + * on a given bus, and attach them to the bus + */ +int mdiobus_register(struct mii_bus *bus) +{ + int i; + int err = 0; + + spin_lock_init(&bus->mdio_lock); + + if (NULL == bus || NULL == bus->name || + NULL == bus->read || + NULL == bus->write) + return -EINVAL; + + if (bus->reset) + bus->reset(bus); + + for (i = 0; i < PHY_MAX_ADDR; i++) { + struct phy_device *phydev; + + phydev = get_phy_device(bus, i); + + if (IS_ERR(phydev)) + return PTR_ERR(phydev); + + /* There's a PHY at this address + * We need to set: + * 1) IRQ + * 2) bus_id + * 3) parent + * 4) bus + * 5) mii_bus + * And, we need to register it */ + if (phydev) { + phydev->irq = bus->irq[i]; + + phydev->dev.parent = bus->dev; + phydev->dev.bus = &mdio_bus_type; + sprintf(phydev->dev.bus_id, "phy%d:%d", bus->id, i); + + phydev->bus = bus; + + err = device_register(&phydev->dev); + + if (err) + printk(KERN_ERR "phy %d failed to register\n", + i); + } + + bus->phy_map[i] = phydev; + } + + pr_info("%s: probed\n", bus->name); + + return err; +} +EXPORT_SYMBOL(mdiobus_register); + +void mdiobus_unregister(struct mii_bus *bus) +{ + int i; + + for (i = 0; i < PHY_MAX_ADDR; i++) { + if (bus->phy_map[i]) { + device_unregister(&bus->phy_map[i]->dev); + kfree(bus->phy_map[i]); + } + } +} +EXPORT_SYMBOL(mdiobus_unregister); + /* mdio_bus_match * * description: Given a PHY device, and a PHY driver, return 1 if @@ -96,4 +170,7 @@ int __init mdio_bus_init(void) return bus_register(&mdio_bus_type); } - +void __exit mdio_bus_exit(void) +{ + bus_unregister(&mdio_bus_type); +} diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index d3e43631..d9e11f9 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -39,10 +39,20 @@ #include #include -static void phy_timer(unsigned long data); -static int phy_disable_interrupts(struct phy_device *phydev); -static void phy_sanitize_settings(struct phy_device *phydev); -static int phy_stop_interrupts(struct phy_device *phydev); +/* Convenience function to print out the current phy status + */ +void phy_print_status(struct phy_device *phydev) +{ + pr_info("%s: Link is %s", phydev->dev.bus_id, + phydev->link ? "Up" : "Down"); + if (phydev->link) + printk(" - %d/%s", phydev->speed, + DUPLEX_FULL == phydev->duplex ? + "Full" : "Half"); + + printk("\n"); +} +EXPORT_SYMBOL(phy_print_status); /* Convenience functions for reading/writing a given PHY @@ -114,42 +124,6 @@ static inline int phy_aneg_done(struct phy_device *phydev) return (retval < 0) ? retval : (retval & BMSR_ANEGCOMPLETE); } -/* phy_start_aneg - * - * description: Calls the PHY driver's config_aneg, and then - * sets the PHY state to PHY_AN if auto-negotiation is enabled, - * and to PHY_FORCING if auto-negotiation is disabled. Unless - * the PHY is currently HALTED. - */ -static int phy_start_aneg(struct phy_device *phydev) -{ - int err; - - spin_lock(&phydev->lock); - - if (AUTONEG_DISABLE == phydev->autoneg) - phy_sanitize_settings(phydev); - - err = phydev->drv->config_aneg(phydev); - - if (err < 0) - goto out_unlock; - - if (phydev->state != PHY_HALTED) { - if (AUTONEG_ENABLE == phydev->autoneg) { - phydev->state = PHY_AN; - phydev->link_timeout = PHY_AN_TIMEOUT; - } else { - phydev->state = PHY_FORCING; - phydev->link_timeout = PHY_FORCE_TIMEOUT; - } - } - -out_unlock: - spin_unlock(&phydev->lock); - return err; -} - /* A structure for mapping a particular speed and duplex * combination to a particular SUPPORTED and ADVERTISED value */ struct phy_setting { @@ -241,7 +215,7 @@ static inline int phy_find_valid(int idx, u32 features) * duplexes. Drop down by one in this order: 1000/FULL, * 1000/HALF, 100/FULL, 100/HALF, 10/FULL, 10/HALF */ -static void phy_sanitize_settings(struct phy_device *phydev) +void phy_sanitize_settings(struct phy_device *phydev) { u32 features = phydev->supported; int idx; @@ -256,31 +230,7 @@ static void phy_sanitize_settings(struct phy_device *phydev) phydev->speed = settings[idx].speed; phydev->duplex = settings[idx].duplex; } - -/* phy_force_reduction - * - * description: Reduces the speed/duplex settings by - * one notch. The order is so: - * 1000/FULL, 1000/HALF, 100/FULL, 100/HALF, - * 10/FULL, 10/HALF. The function bottoms out at 10/HALF. - */ -static void phy_force_reduction(struct phy_device *phydev) -{ - int idx; - - idx = phy_find_setting(phydev->speed, phydev->duplex); - - idx++; - - idx = phy_find_valid(idx, phydev->supported); - - phydev->speed = settings[idx].speed; - phydev->duplex = settings[idx].duplex; - - pr_info("Trying %d/%s\n", phydev->speed, - DUPLEX_FULL == phydev->duplex ? - "FULL" : "HALF"); -} +EXPORT_SYMBOL(phy_sanitize_settings); /* phy_ethtool_sset: * A generic ethtool sset function. Handles all the details @@ -291,6 +241,11 @@ static void phy_force_reduction(struct phy_device *phydev) * - phy_start_aneg() will make sure forced settings are sane, and * choose the next best ones from the ones selected, so we don't * care if ethtool tries to give us bad values + * + * A note about the PHYCONTROL Layer. If you turn off + * CONFIG_PHYCONTROL, you will need to read the PHY status + * registers after this function completes, and update your + * controller manually. */ int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd) { @@ -406,6 +361,51 @@ int phy_mii_ioctl(struct phy_device *phydev, return 0; } +/* phy_start_aneg + * + * description: Sanitizes the settings (if we're not + * autonegotiating them), and then calls the driver's + * config_aneg function. If the PHYCONTROL Layer is operating, + * we change the state to reflect the beginning of + * Auto-negotiation or forcing. + */ +int phy_start_aneg(struct phy_device *phydev) +{ + int err; + + spin_lock(&phydev->lock); + + if (AUTONEG_DISABLE == phydev->autoneg) + phy_sanitize_settings(phydev); + + err = phydev->drv->config_aneg(phydev); + +#ifdef CONFIG_PHYCONTROL + if (err < 0) + goto out_unlock; + + if (phydev->state != PHY_HALTED) { + if (AUTONEG_ENABLE == phydev->autoneg) { + phydev->state = PHY_AN; + phydev->link_timeout = PHY_AN_TIMEOUT; + } else { + phydev->state = PHY_FORCING; + phydev->link_timeout = PHY_FORCE_TIMEOUT; + } + } + +out_unlock: +#endif + spin_unlock(&phydev->lock); + return err; +} +EXPORT_SYMBOL(phy_start_aneg); + + +#ifdef CONFIG_PHYCONTROL +static void phy_change(void *data); +static void phy_timer(unsigned long data); + /* phy_start_machine: * * description: The PHY infrastructure can run a state machine @@ -448,6 +448,32 @@ void phy_stop_machine(struct phy_device *phydev) phydev->adjust_state = NULL; } +/* phy_force_reduction + * + * description: Reduces the speed/duplex settings by + * one notch. The order is so: + * 1000/FULL, 1000/HALF, 100/FULL, 100/HALF, + * 10/FULL, 10/HALF. The function bottoms out at 10/HALF. + */ +static void phy_force_reduction(struct phy_device *phydev) +{ + int idx; + + idx = phy_find_setting(phydev->speed, phydev->duplex); + + idx++; + + idx = phy_find_valid(idx, phydev->supported); + + phydev->speed = settings[idx].speed; + phydev->duplex = settings[idx].duplex; + + pr_info("Trying %d/%s\n", phydev->speed, + DUPLEX_FULL == phydev->duplex ? + "FULL" : "HALF"); +} + + /* phy_error: * * Moves the PHY to the HALTED state in response to a read @@ -462,22 +488,44 @@ void phy_error(struct phy_device *phydev) spin_unlock(&phydev->lock); } -static int phy_stop_interrupts(struct phy_device *phydev) +/* phy_interrupt + * + * description: When a PHY interrupt occurs, the handler disables + * interrupts, and schedules a work task to clear the interrupt. + */ +static irqreturn_t phy_interrupt(int irq, void *phy_dat, struct pt_regs *regs) +{ + struct phy_device *phydev = phy_dat; + + /* The MDIO bus is not allowed to be written in interrupt + * context, so we need to disable the irq here. A work + * queue will write the PHY to disable and clear the + * interrupt, and then reenable the irq line. */ + disable_irq_nosync(irq); + + schedule_work(&phydev->phy_queue); + + return IRQ_HANDLED; +} + +/* Enable the interrupts from the PHY side */ +int phy_enable_interrupts(struct phy_device *phydev) { int err; - err = phy_disable_interrupts(phydev); + err = phy_clear_interrupt(phydev); - if (err) - phy_error(phydev); + if (err < 0) + return err; - free_irq(phydev->irq, phydev); + err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); return err; } +EXPORT_SYMBOL(phy_enable_interrupts); /* Disable the PHY interrupts from the PHY side */ -static int phy_disable_interrupts(struct phy_device *phydev) +int phy_disable_interrupts(struct phy_device *phydev) { int err; @@ -500,6 +548,138 @@ phy_err: return err; } +EXPORT_SYMBOL(phy_disable_interrupts); + +/* phy_start_interrupts + * + * description: Request the interrupt for the given PHY. If + * this fails, then we set irq to PHY_POLL. + * Otherwise, we enable the interrupts in the PHY. + * Returns 0 on success. + * This should only be called with a valid IRQ number. + */ +int phy_start_interrupts(struct phy_device *phydev) +{ + int err = 0; + + INIT_WORK(&phydev->phy_queue, phy_change, phydev); + + if (request_irq(phydev->irq, phy_interrupt, + SA_SHIRQ, + "phy_interrupt", + phydev) < 0) { + printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n", + phydev->bus->name, + phydev->irq); + phydev->irq = PHY_POLL; + return 0; + } + + err = phy_enable_interrupts(phydev); + + return err; +} +EXPORT_SYMBOL(phy_start_interrupts); + +int phy_stop_interrupts(struct phy_device *phydev) +{ + int err; + + err = phy_disable_interrupts(phydev); + + if (err) + phy_error(phydev); + + free_irq(phydev->irq, phydev); + + return err; +} +EXPORT_SYMBOL(phy_stop_interrupts); + + +/* Scheduled by the phy_interrupt/timer to handle PHY changes */ +static void phy_change(void *data) +{ + int err; + struct phy_device *phydev = data; + + err = phy_disable_interrupts(phydev); + + if (err) + goto phy_err; + + spin_lock(&phydev->lock); + if ((PHY_RUNNING == phydev->state) || (PHY_NOLINK == phydev->state)) + phydev->state = PHY_CHANGELINK; + spin_unlock(&phydev->lock); + + enable_irq(phydev->irq); + + /* Reenable interrupts */ + err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); + + if (err) + goto irq_enable_err; + + return; + +irq_enable_err: + disable_irq(phydev->irq); +phy_err: + phy_error(phydev); +} + +/* Bring down the PHY link, and stop checking the status. */ +void phy_stop(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + + if (PHY_HALTED == phydev->state) + goto out_unlock; + + if (phydev->irq != PHY_POLL) { + /* Clear any pending interrupts */ + phy_clear_interrupt(phydev); + + /* Disable PHY Interrupts */ + phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); + } + + phydev->state = PHY_HALTED; + +out_unlock: + spin_unlock(&phydev->lock); +} + + +/* phy_start + * + * description: Indicates the attached device's readiness to + * handle PHY-related work. Used during startup to start the + * PHY, and after a call to phy_stop() to resume operation. + * Also used to indicate the MDIO bus has cleared an error + * condition. + */ +void phy_start(struct phy_device *phydev) +{ + spin_lock(&phydev->lock); + + switch (phydev->state) { + case PHY_STARTING: + phydev->state = PHY_PENDING; + break; + case PHY_READY: + phydev->state = PHY_UP; + break; + case PHY_HALTED: + phydev->state = PHY_RESUMING; + default: + break; + } + spin_unlock(&phydev->lock); +} +EXPORT_SYMBOL(phy_stop); +EXPORT_SYMBOL(phy_start); /* PHY timer which handles the state machine */ static void phy_timer(unsigned long data) @@ -688,3 +868,4 @@ static void phy_timer(unsigned long data) mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ); } +#endif /* CONFIG_PHYCONTROL */ diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index c44d54f..33f7bdb 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -39,18 +39,9 @@ #include #include -static int genphy_config_init(struct phy_device *phydev); - -static struct phy_driver genphy_driver = { - .phy_id = 0xffffffff, - .phy_id_mask = 0xffffffff, - .name = "Generic PHY", - .config_init = genphy_config_init, - .features = 0, - .config_aneg = genphy_config_aneg, - .read_status = genphy_read_status, - .driver = {.owner = THIS_MODULE, }, -}; +static struct phy_driver genphy_driver; +extern int mdio_bus_init(void); +extern void mdio_bus_exit(void); /* get_phy_device * @@ -110,6 +101,7 @@ struct phy_device * get_phy_device(struct mii_bus *bus, int addr) return dev; } +#ifdef CONFIG_PHYCONTROL /* phy_prepare_link: * * description: Tells the PHY infrastructure to handle the @@ -124,6 +116,132 @@ void phy_prepare_link(struct phy_device *phydev, phydev->adjust_link = handler; } +/* phy_connect: + * + * description: Convenience function for connecting ethernet + * devices to PHY devices. The default behavior is for + * the PHY infrastructure to handle everything, and only notify + * the connected driver when the link status changes. If you + * don't want, or can't use the provided functionality, you may + * choose to call only the subset of functions which provide + * the desired functionality. + */ +struct phy_device * phy_connect(struct net_device *dev, const char *phy_id, + void (*handler)(struct net_device *), u32 flags) +{ + struct phy_device *phydev; + + phydev = phy_attach(dev, phy_id, flags); + + if (IS_ERR(phydev)) + return phydev; + + phy_prepare_link(phydev, handler); + + phy_start_machine(phydev, NULL); + + if (phydev->irq > 0) + phy_start_interrupts(phydev); + + return phydev; +} +EXPORT_SYMBOL(phy_connect); + +void phy_disconnect(struct phy_device *phydev) +{ + if (phydev->irq > 0) + phy_stop_interrupts(phydev); + + phy_stop_machine(phydev); + + phydev->adjust_link = NULL; + + phy_detach(phydev); +} +EXPORT_SYMBOL(phy_disconnect); + +#endif /* CONFIG_PHYCONTROL */ + +/* phy_attach: + * + * description: Called by drivers to attach to a particular PHY + * device. The phy_device is found, and properly hooked up + * to the phy_driver. If no driver is attached, then the + * genphy_driver is used. The phy_device is given a ptr to + * the attaching device, and given a callback for link status + * change. The phy_device is returned to the attaching + * driver. + */ +static int phy_compare_id(struct device *dev, void *data) +{ + return strcmp((char *)data, dev->bus_id) ? 0 : 1; +} + +struct phy_device *phy_attach(struct net_device *dev, + const char *phy_id, u32 flags) +{ + struct bus_type *bus = &mdio_bus_type; + struct phy_device *phydev; + struct device *d; + + /* Search the list of PHY devices on the mdio bus for the + * PHY with the requested name */ + d = bus_find_device(bus, NULL, (void *)phy_id, phy_compare_id); + + if (d) { + phydev = to_phy_device(d); + } else { + printk(KERN_ERR "%s not found\n", phy_id); + return ERR_PTR(-ENODEV); + } + + /* Assume that if there is no driver, that it doesn't + * exist, and we should use the genphy driver. */ + if (NULL == d->driver) { + int err; + down_write(&d->bus->subsys.rwsem); + d->driver = &genphy_driver.driver; + + err = d->driver->probe(d); + + if (err < 0) + return ERR_PTR(err); + + device_bind_driver(d); + up_write(&d->bus->subsys.rwsem); + } + + if (phydev->attached_dev) { + printk(KERN_ERR "%s: %s already attached\n", + dev->name, phy_id); + return ERR_PTR(-EBUSY); + } + + phydev->attached_dev = dev; + + phydev->dev_flags = flags; + + return phydev; +} +EXPORT_SYMBOL(phy_attach); + +void phy_detach(struct phy_device *phydev) +{ + phydev->attached_dev = NULL; + + /* If the device had no specific driver before (i.e. - it + * was using the generic driver), we unbind the device + * from the generic driver so that there's a chance a + * real driver could be loaded */ + if (phydev->dev.driver == &genphy_driver.driver) { + down_write(&phydev->dev.bus->subsys.rwsem); + device_release_driver(&phydev->dev); + up_write(&phydev->dev.bus->subsys.rwsem); + } +} +EXPORT_SYMBOL(phy_detach); + + /* Generic PHY support and helper functions */ /* genphy_config_advert @@ -132,7 +250,7 @@ void phy_prepare_link(struct phy_device *phydev, * after sanitizing the values to make sure we only advertise * what is supported */ -static int genphy_config_advert(struct phy_device *phydev) +int genphy_config_advert(struct phy_device *phydev) { u32 advertise; int adv; @@ -190,6 +308,7 @@ static int genphy_config_advert(struct phy_device *phydev) return adv; } +EXPORT_SYMBOL(genphy_config_advert); /* genphy_setup_forced * @@ -541,32 +660,37 @@ void phy_driver_unregister(struct phy_driver *drv) } EXPORT_SYMBOL(phy_driver_unregister); +static struct phy_driver genphy_driver = { + .phy_id = 0xffffffff, + .phy_id_mask = 0xffffffff, + .name = "Generic PHY", + .config_init = genphy_config_init, + .features = 0, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .driver = {.owner= THIS_MODULE, }, +}; static int __init phy_init(void) { int rc; - extern int mdio_bus_init(void); - - rc = phy_driver_register(&genphy_driver); - if (rc) - goto out; rc = mdio_bus_init(); if (rc) - goto out_unreg; + return rc; - return 0; + rc = phy_driver_register(&genphy_driver); + if (rc) + mdio_bus_exit(); -out_unreg: - phy_driver_unregister(&genphy_driver); -out: return rc; } static void __exit phy_exit(void) { phy_driver_unregister(&genphy_driver); + mdio_bus_exit(); } -module_init(phy_init); +subsys_initcall(phy_init); module_exit(phy_exit); diff --git a/include/linux/phy.h b/include/linux/phy.h index 4f2b5ef..72cb67b 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -334,11 +334,26 @@ int phy_write(struct phy_device *phydev, u16 regnum, u16 val); struct phy_device* get_phy_device(struct mii_bus *bus, int addr); int phy_clear_interrupt(struct phy_device *phydev); int phy_config_interrupt(struct phy_device *phydev, u32 interrupts); +struct phy_device * phy_attach(struct net_device *dev, + const char *phy_id, u32 flags); +struct phy_device * phy_connect(struct net_device *dev, const char *phy_id, + void (*handler)(struct net_device *), u32 flags); +void phy_disconnect(struct phy_device *phydev); +void phy_detach(struct phy_device *phydev); +void phy_start(struct phy_device *phydev); +void phy_stop(struct phy_device *phydev); +int phy_start_aneg(struct phy_device *phydev); + +int mdiobus_register(struct mii_bus *bus); +void mdiobus_unregister(struct mii_bus *bus); +void phy_sanitize_settings(struct phy_device *phydev); +int phy_stop_interrupts(struct phy_device *phydev); static inline int phy_read_status(struct phy_device *phydev) { return phydev->drv->read_status(phydev); } +int genphy_config_advert(struct phy_device *phydev); int genphy_setup_forced(struct phy_device *phydev); int genphy_restart_aneg(struct phy_device *phydev); int genphy_config_aneg(struct phy_device *phydev); @@ -355,6 +370,8 @@ int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd); int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd); int phy_mii_ioctl(struct phy_device *phydev, struct mii_ioctl_data *mii_data, int cmd); +int phy_start_interrupts(struct phy_device *phydev); +void phy_print_status(struct phy_device *phydev); extern struct bus_type mdio_bus_type; #endif /* __PHY_H */ -- cgit v0.10.2