From 9b2256c8274c72bacb7eca7dee5ffe85832cb5e0 Mon Sep 17 00:00:00 2001 From: Mans Rullgard Date: Tue, 15 Sep 2015 17:54:13 +0100 Subject: serial: 8250: simplify ralink/alchemy register remap selection Some SoCs, including Ralink/Mediatek and Alchemy Au1xxx, have a 16550-like UART with a non-standard register layout. These are supported by a simple mapping table in 8250_port.c Rather than list every SoC type using this access mode in the ifdefs there, allow selecting the SERIAL_8250_RT288X Kconfig option with any system and default it to y for the known cases needing it. The help text is reworded accordingly. This change simplifies adding support for other SoCs also using the same UART. The name of the option is a little misleading, but not knowing the true origin of this UART, it is as good a choice as any. Signed-off-by: Mans Rullgard Signed-off-by: Greg Kroah-Hartman diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c index c4dac1b..554a63e 100644 --- a/drivers/tty/serial/8250/8250_port.c +++ b/drivers/tty/serial/8250/8250_port.c @@ -276,7 +276,7 @@ static void default_serial_dl_write(struct uart_8250_port *up, int value) serial_out(up, UART_DLM, value >> 8 & 0xff); } -#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) +#ifdef CONFIG_SERIAL_8250_RT288X /* Au1x00/RT288x UART hardware has a weird register layout */ static const s8 au_io_in_map[8] = { @@ -427,7 +427,7 @@ static void set_io_from_upio(struct uart_port *p) p->serial_out = mem32be_serial_out; break; -#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) +#ifdef CONFIG_SERIAL_8250_RT288X case UPIO_AU: p->serial_in = au_serial_in; p->serial_out = au_serial_out; diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index f5c4b01..656a173 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -294,11 +294,12 @@ config SERIAL_8250_EM config SERIAL_8250_RT288X bool "Ralink RT288x/RT305x/RT3662/RT3883 serial port support" - depends on SERIAL_8250 && (SOC_RT288X || SOC_RT305X || SOC_RT3883 || SOC_MT7620) + depends on SERIAL_8250 + default y if MIPS_ALCHEMY || SOC_RT288X || SOC_RT305X || SOC_RT3883 || SOC_MT7620 help - If you have a Ralink RT288x/RT305x SoC based board and want to use the - serial port, say Y to this option. The driver can handle up to 2 serial - ports. If unsure, say N. + Selecting this option will add support for the alternate register + layout used by Ralink RT288x/RT305x, Alchemy Au1xxx, and some others. + If unsure, say N. config SERIAL_8250_OMAP tristate "Support for OMAP internal UART (8250 based driver)" -- cgit v0.10.2