summaryrefslogtreecommitdiff
path: root/cpu/ppc4xx/start.S
diff options
context:
space:
mode:
Diffstat (limited to 'cpu/ppc4xx/start.S')
-rw-r--r--cpu/ppc4xx/start.S248
1 files changed, 124 insertions, 124 deletions
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index c6a9eda..aa857d0 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -556,9 +556,9 @@ _start:
/*----------------------------------------------------------------------- */
/* DMA Status, clear to come up clean */
/*----------------------------------------------------------------------- */
- addis r3,r0, 0xFFFF /* Clear all existing DMA status */
- ori r3,r3, 0xFFFF
- mtdcr dmasr, r3
+ addis r3,r0, 0xFFFF /* Clear all existing DMA status */
+ ori r3,r3, 0xFFFF
+ mtdcr dmasr, r3
bl ppc405ep_init /* do ppc405ep specific init */
#endif /* CONFIG_405EP */
@@ -568,21 +568,21 @@ _start:
* Setup OCM - On Chip Memory
*******************************************************************/
/* Setup OCM */
- lis r0, 0x7FFF
- ori r0, r0, 0xFFFF
- mfdcr r3, ocmiscntl /* get instr-side IRAM config */
- mfdcr r4, ocmdscntl /* get data-side IRAM config */
- and r3, r3, r0 /* disable data-side IRAM */
- and r4, r4, r0 /* disable data-side IRAM */
- mtdcr ocmiscntl, r3 /* set instr-side IRAM config */
- mtdcr ocmdscntl, r4 /* set data-side IRAM config */
- isync
+ lis r0, 0x7FFF
+ ori r0, r0, 0xFFFF
+ mfdcr r3, ocmiscntl /* get instr-side IRAM config */
+ mfdcr r4, ocmdscntl /* get data-side IRAM config */
+ and r3, r3, r0 /* disable data-side IRAM */
+ and r4, r4, r0 /* disable data-side IRAM */
+ mtdcr ocmiscntl, r3 /* set instr-side IRAM config */
+ mtdcr ocmdscntl, r4 /* set data-side IRAM config */
+ isync
addis r3, 0, CFG_OCM_DATA_ADDR@h /* OCM location */
mtdcr ocmdsarc, r3
addis r4, 0, 0xC000 /* OCM data area enabled */
mtdcr ocmdscntl, r4
- isync
+ isync
#endif
/*----------------------------------------------------------------------- */
@@ -697,7 +697,7 @@ _start:
GET_GOT /* initialize GOT access */
- bl cpu_init_f /* run low-level CPU init code (from Flash) */
+ bl cpu_init_f /* run low-level CPU init code (from Flash) */
/* NEVER RETURNS! */
bl board_init_f /* run first part of init code (from Flash) */
@@ -1451,100 +1451,100 @@ trap_reloc:
/**************************************************************************/
#ifdef CONFIG_405EP
ppc405ep_init:
- /*
- !-----------------------------------------------------------------------
- ! Check FPGA for PCI internal/external arbitration
- ! If board is set to internal arbitration, update cpc0_pci
- !-----------------------------------------------------------------------
+ /*
+ !-----------------------------------------------------------------------
+ ! Check FPGA for PCI internal/external arbitration
+ ! If board is set to internal arbitration, update cpc0_pci
+ !-----------------------------------------------------------------------
*/
- addi r3,0,CPC0_PCI_HOST_CFG_EN
+ addi r3,0,CPC0_PCI_HOST_CFG_EN
#ifdef CONFIG_BUBINGA405EP
- addis r5,r0,FPGA_REG1@h /* set offset for FPGA_REG1 */
- ori r5,r5,FPGA_REG1@l
- lbz r5,0x0(r5) /* read to get PCI arb selection */
- andi. r6,r5,FPGA_REG1_PCI_INT_ARB /* using internal arbiter ?*/
- beq ..pci_cfg_set /* if not set, then bypass reg write*/
+ addis r5,r0,FPGA_REG1@h /* set offset for FPGA_REG1 */
+ ori r5,r5,FPGA_REG1@l
+ lbz r5,0x0(r5) /* read to get PCI arb selection */
+ andi. r6,r5,FPGA_REG1_PCI_INT_ARB /* using internal arbiter ?*/
+ beq ..pci_cfg_set /* if not set, then bypass reg write*/
#endif
- ori r3,r3,CPC0_PCI_ARBIT_EN
+ ori r3,r3,CPC0_PCI_ARBIT_EN
..pci_cfg_set:
- mtdcr CPC0_PCI, r3 /* Enable internal arbiter*/
-
- /*
- !-----------------------------------------------------------------------
- ! Check to see if chip is in bypass mode.
- ! If so, write stored CPC0_PLLMR0 and CPC0_PLLMR1 values and perform a
- ! CPU reset Otherwise, skip this step and keep going.
- ! Note: Running BIOS in bypass mode is not supported since PLB speed
- ! will not be fast enough for the SDRAM (min 66MHz)
- !-----------------------------------------------------------------------
+ mtdcr CPC0_PCI, r3 /* Enable internal arbiter*/
+
+ /*
+ !-----------------------------------------------------------------------
+ ! Check to see if chip is in bypass mode.
+ ! If so, write stored CPC0_PLLMR0 and CPC0_PLLMR1 values and perform a
+ ! CPU reset Otherwise, skip this step and keep going.
+ ! Note: Running BIOS in bypass mode is not supported since PLB speed
+ ! will not be fast enough for the SDRAM (min 66MHz)
+ !-----------------------------------------------------------------------
*/
- mfdcr r5, CPC0_PLLMR1
- rlwinm r4,r5,1,0x1 /* get system clock source (SSCS) */
- cmpi cr0,0,r4,0x1
+ mfdcr r5, CPC0_PLLMR1
+ rlwinm r4,r5,1,0x1 /* get system clock source (SSCS) */
+ cmpi cr0,0,r4,0x1
- beq pll_done /* if SSCS =b'1' then PLL has */
- /* already been set */
- /* and CPU has been reset */
- /* so skip to next section */
+ beq pll_done /* if SSCS =b'1' then PLL has */
+ /* already been set */
+ /* and CPU has been reset */
+ /* so skip to next section */
#ifdef CONFIG_BUBINGA405EP
/*
- !-----------------------------------------------------------------------
- ! Read NVRAM to get value to write in PLLMR.
- ! If value has not been correctly saved, write default value
- ! Default config values (assuming on-board 33MHz SYS_CLK) are above.
- ! See CPU_DEFAULT_200 and CPU_DEFAULT_266 above.
- !
- ! WARNING: This code assumes the first three words in the nvram_t
- ! structure in openbios.h. Changing the beginning of
- ! the structure will break this code.
- !
- !-----------------------------------------------------------------------
+ !-----------------------------------------------------------------------
+ ! Read NVRAM to get value to write in PLLMR.
+ ! If value has not been correctly saved, write default value
+ ! Default config values (assuming on-board 33MHz SYS_CLK) are above.
+ ! See CPU_DEFAULT_200 and CPU_DEFAULT_266 above.
+ !
+ ! WARNING: This code assumes the first three words in the nvram_t
+ ! structure in openbios.h. Changing the beginning of
+ ! the structure will break this code.
+ !
+ !-----------------------------------------------------------------------
*/
- addis r3,0,NVRAM_BASE@h
- addi r3,r3,NVRAM_BASE@l
-
- lwz r4, 0(r3)
- addis r5,0,NVRVFY1@h
- addi r5,r5,NVRVFY1@l
- cmp cr0,0,r4,r5 /* Compare 1st NVRAM Magic number*/
- bne ..no_pllset
- addi r3,r3,4
- lwz r4, 0(r3)
- addis r5,0,NVRVFY2@h
- addi r5,r5,NVRVFY2@l
- cmp cr0,0,r4,r5 /* Compare 2 NVRAM Magic number */
- bne ..no_pllset
- addi r3,r3,8 /* Skip over conf_size */
- lwz r4, 4(r3) /* Load PLLMR1 value from NVRAM */
- lwz r3, 0(r3) /* Load PLLMR0 value from NVRAM */
- rlwinm r5,r4,1,0x1 /* get system clock source (SSCS) */
- cmpi cr0,0,r5,1 /* See if PLL is locked */
- beq pll_write
+ addis r3,0,NVRAM_BASE@h
+ addi r3,r3,NVRAM_BASE@l
+
+ lwz r4, 0(r3)
+ addis r5,0,NVRVFY1@h
+ addi r5,r5,NVRVFY1@l
+ cmp cr0,0,r4,r5 /* Compare 1st NVRAM Magic number*/
+ bne ..no_pllset
+ addi r3,r3,4
+ lwz r4, 0(r3)
+ addis r5,0,NVRVFY2@h
+ addi r5,r5,NVRVFY2@l
+ cmp cr0,0,r4,r5 /* Compare 2 NVRAM Magic number */
+ bne ..no_pllset
+ addi r3,r3,8 /* Skip over conf_size */
+ lwz r4, 4(r3) /* Load PLLMR1 value from NVRAM */
+ lwz r3, 0(r3) /* Load PLLMR0 value from NVRAM */
+ rlwinm r5,r4,1,0x1 /* get system clock source (SSCS) */
+ cmpi cr0,0,r5,1 /* See if PLL is locked */
+ beq pll_write
..no_pllset:
#endif /* CONFIG_BUBINGA405EP */
- addis r3,0,PLLMR0_DEFAULT@h /* PLLMR0 default value */
- ori r3,r3,PLLMR0_DEFAULT@l /* */
- addis r4,0,PLLMR1_DEFAULT@h /* PLLMR1 default value */
- ori r4,r4,PLLMR1_DEFAULT@l /* */
+ addis r3,0,PLLMR0_DEFAULT@h /* PLLMR0 default value */
+ ori r3,r3,PLLMR0_DEFAULT@l /* */
+ addis r4,0,PLLMR1_DEFAULT@h /* PLLMR1 default value */
+ ori r4,r4,PLLMR1_DEFAULT@l /* */
- b pll_write /* Write the CPC0_PLLMR with new value */
+ b pll_write /* Write the CPC0_PLLMR with new value */
pll_done:
- /*
- !-----------------------------------------------------------------------
- ! Clear Soft Reset Register
- ! This is needed to enable PCI if not booting from serial EPROM
- !-----------------------------------------------------------------------
+ /*
+ !-----------------------------------------------------------------------
+ ! Clear Soft Reset Register
+ ! This is needed to enable PCI if not booting from serial EPROM
+ !-----------------------------------------------------------------------
*/
- addi r3, 0, 0x0
- mtdcr CPC0_SRR, r3
+ addi r3, 0, 0x0
+ mtdcr CPC0_SRR, r3
- addis r3,0,0x0010
- mtctr r3
+ addis r3,0,0x0010
+ mtctr r3
pci_wait:
- bdnz pci_wait
+ bdnz pci_wait
blr /* return to main code */
@@ -1565,43 +1565,43 @@ pci_wait:
!-----------------------------------------------------------------------------
*/
pll_write:
- mfdcr r5, CPC0_UCR
- andis. r5,r5,0xFFFF
- ori r5,r5,0x0101 /* Stop the UART clocks */
- mtdcr CPC0_UCR,r5 /* Before changing PLL */
-
- mfdcr r5, CPC0_PLLMR1
- rlwinm r5,r5,0,0x7FFFFFFF /* Disable PLL */
- mtdcr CPC0_PLLMR1,r5
- oris r5,r5,0x4000 /* Set PLL Reset */
- mtdcr CPC0_PLLMR1,r5
-
- mtdcr CPC0_PLLMR0,r3 /* Set clock dividers */
- rlwinm r5,r4,0,0x3FFFFFFF /* Reset & Bypass new PLL dividers */
- oris r5,r5,0x4000 /* Set PLL Reset */
- mtdcr CPC0_PLLMR1,r5 /* Set clock dividers */
- rlwinm r5,r5,0,0xBFFFFFFF /* Clear PLL Reset */
- mtdcr CPC0_PLLMR1,r5
+ mfdcr r5, CPC0_UCR
+ andis. r5,r5,0xFFFF
+ ori r5,r5,0x0101 /* Stop the UART clocks */
+ mtdcr CPC0_UCR,r5 /* Before changing PLL */
+
+ mfdcr r5, CPC0_PLLMR1
+ rlwinm r5,r5,0,0x7FFFFFFF /* Disable PLL */
+ mtdcr CPC0_PLLMR1,r5
+ oris r5,r5,0x4000 /* Set PLL Reset */
+ mtdcr CPC0_PLLMR1,r5
+
+ mtdcr CPC0_PLLMR0,r3 /* Set clock dividers */
+ rlwinm r5,r4,0,0x3FFFFFFF /* Reset & Bypass new PLL dividers */
+ oris r5,r5,0x4000 /* Set PLL Reset */
+ mtdcr CPC0_PLLMR1,r5 /* Set clock dividers */
+ rlwinm r5,r5,0,0xBFFFFFFF /* Clear PLL Reset */
+ mtdcr CPC0_PLLMR1,r5
/*
- ! Wait min of 100us for PLL to lock.
- ! See CMOS 27E databook for more info.
- ! At 200MHz, that means waiting 20,000 instructions
+ ! Wait min of 100us for PLL to lock.
+ ! See CMOS 27E databook for more info.
+ ! At 200MHz, that means waiting 20,000 instructions
*/
- addi r3,0,20000 /* 2000 = 0x4e20 */
- mtctr r3
+ addi r3,0,20000 /* 2000 = 0x4e20 */
+ mtctr r3
pll_wait:
- bdnz pll_wait
-
- oris r5,r5,0x8000 /* Enable PLL */
- mtdcr CPC0_PLLMR1,r5 /* Engage */
-
- /*
- * Reset CPU to guarantee timings are OK
- * Not sure if this is needed...
- */
- addis r3,0,0x1000
- mtspr dbcr0,r3 /* This will cause a CPU core reset, and */
- /* execution will continue from the poweron */
- /* vector of 0xfffffffc */
+ bdnz pll_wait
+
+ oris r5,r5,0x8000 /* Enable PLL */
+ mtdcr CPC0_PLLMR1,r5 /* Engage */
+
+ /*
+ * Reset CPU to guarantee timings are OK
+ * Not sure if this is needed...
+ */
+ addis r3,0,0x1000
+ mtspr dbcr0,r3 /* This will cause a CPU core reset, and */
+ /* execution will continue from the poweron */
+ /* vector of 0xfffffffc */
#endif /* CONFIG_405EP */