From 41fbbbbc71161e0c0479d7c6c5598e760d70f624 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Tue, 24 Feb 2015 11:45:05 +0900 Subject: ARM: remove jadecpu board support This is still a non-generic board. Signed-off-by: Masahiro Yamada Cc: Matthias Weisser Acked-by: Marek Vasut diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 3408319..089bef2 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -144,10 +144,6 @@ config TARGET_DEVKIT3250 bool "Support devkit3250" select CPU_ARM926EJS -config TARGET_JADECPU - bool "Support jadecpu" - select CPU_ARM926EJS - config TARGET_MX25PDK bool "Support mx25pdk" select CPU_ARM926EJS @@ -852,7 +848,6 @@ source "board/st-ericsson/snowball/Kconfig" source "board/st-ericsson/u8500/Kconfig" source "board/st/stv0991/Kconfig" source "board/sunxi/Kconfig" -source "board/syteco/jadecpu/Kconfig" source "board/syteco/zmx25/Kconfig" source "board/tbs/tbs2910/Kconfig" source "board/ti/am335x/Kconfig" diff --git a/arch/arm/cpu/arm926ejs/Makefile b/arch/arm/cpu/arm926ejs/Makefile index f5944cc..ac23116 100644 --- a/arch/arm/cpu/arm926ejs/Makefile +++ b/arch/arm/cpu/arm926ejs/Makefile @@ -16,7 +16,6 @@ endif obj-$(CONFIG_ARMADA100) += armada100/ obj-$(if $(filter lpc32xx,$(SOC)),y) += lpc32xx/ -obj-$(CONFIG_MB86R0x) += mb86r0x/ obj-$(CONFIG_MX25) += mx25/ obj-$(CONFIG_MX27) += mx27/ obj-$(if $(filter mxs,$(SOC)),y) += mxs/ diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/Makefile b/arch/arm/cpu/arm926ejs/mb86r0x/Makefile deleted file mode 100644 index 365892c..0000000 --- a/arch/arm/cpu/arm926ejs/mb86r0x/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = clock.o reset.o timer.o diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/clock.c b/arch/arm/cpu/arm926ejs/mb86r0x/clock.c deleted file mode 100644 index 1f6f66e..0000000 --- a/arch/arm/cpu/arm926ejs/mb86r0x/clock.c +++ /dev/null @@ -1,27 +0,0 @@ -/* - * (C) Copyright 2010 - * Matthias Weisser - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -/* - * Get the peripheral bus frequency depending on pll pin settings - */ -ulong get_bus_freq(ulong dummy) -{ - struct mb86r0x_crg * crg = (struct mb86r0x_crg *) - MB86R0x_CRG_BASE; - uint32_t pllmode; - - pllmode = readl(&crg->crpr) & MB86R0x_CRG_CRPR_PLLMODE; - - if (pllmode == MB86R0x_CRG_CRPR_PLLMODE_X20) - return 40000000; - - return 41164767; -} diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/reset.c b/arch/arm/cpu/arm926ejs/mb86r0x/reset.c deleted file mode 100644 index 7bd77ff..0000000 --- a/arch/arm/cpu/arm926ejs/mb86r0x/reset.c +++ /dev/null @@ -1,24 +0,0 @@ -/* - * (C) Copyright 2010 - * Matthias Weisser - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -/* - * Reset the cpu by setting software reset request bit - */ -void reset_cpu(ulong ignored) -{ - struct mb86r0x_crg * crg = (struct mb86r0x_crg *) - MB86R0x_CRG_BASE; - - writel(MB86R0x_CRSR_SWRSTREQ, &crg->crsr); - while (1) - /* NOP */; - /* Never reached */ -} diff --git a/arch/arm/cpu/arm926ejs/mb86r0x/timer.c b/arch/arm/cpu/arm926ejs/mb86r0x/timer.c deleted file mode 100644 index bb07819..0000000 --- a/arch/arm/cpu/arm926ejs/mb86r0x/timer.c +++ /dev/null @@ -1,115 +0,0 @@ -/* - * (C) Copyright 2007-2008 - * Stelian Pop - * Lead Tech Design - * - * (C) Copyright 2010 - * Matthias Weisser, Graf-Syteco - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -#define TIMER_LOAD_VAL 0xffffffff -#define TIMER_FREQ (CONFIG_MB86R0x_IOCLK / 256) - -DECLARE_GLOBAL_DATA_PTR; - -#define timestamp gd->arch.tbl -#define lastdec gd->arch.lastinc - -static inline unsigned long long tick_to_time(unsigned long long tick) -{ - tick *= CONFIG_SYS_HZ; - do_div(tick, TIMER_FREQ); - - return tick; -} - -static inline unsigned long long usec_to_tick(unsigned long long usec) -{ - usec *= TIMER_FREQ; - do_div(usec, 1000000); - - return usec; -} - -/* nothing really to do with interrupts, just starts up a counter. */ -int timer_init(void) -{ - struct mb86r0x_timer * timer = (struct mb86r0x_timer *) - MB86R0x_TIMER_BASE; - ulong ctrl = readl(&timer->control); - - writel(TIMER_LOAD_VAL, &timer->load); - - ctrl |= MB86R0x_TIMER_ENABLE | MB86R0x_TIMER_PRS_8S | - MB86R0x_TIMER_SIZE_32; - - writel(ctrl, &timer->control); - - /* capture current value time */ - lastdec = readl(&timer->value); - timestamp = 0; /* start "advancing" time stamp from 0 */ - - return 0; -} - -/* - * timer without interrupts - */ -unsigned long long get_ticks(void) -{ - struct mb86r0x_timer * timer = (struct mb86r0x_timer *) - MB86R0x_TIMER_BASE; - ulong now = readl(&timer->value); - - if (now <= lastdec) { - /* normal mode (non roll) */ - /* move stamp forward with absolut diff ticks */ - timestamp += lastdec - now; - } else { - /* we have rollover of incrementer */ - timestamp += lastdec + TIMER_LOAD_VAL - now; - } - lastdec = now; - return timestamp; -} - -ulong get_timer_masked(void) -{ - return tick_to_time(get_ticks()); -} - -void __udelay(unsigned long usec) -{ - unsigned long long tmp; - ulong tmo; - - tmo = usec_to_tick(usec); - tmp = get_ticks(); /* get current timestamp */ - - while ((get_ticks() - tmp) < tmo) /* loop till event */ - /*NOP*/; -} - -ulong get_timer(ulong base) -{ - return get_timer_masked() - base; -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk(void) -{ - ulong tbclk; - - tbclk = TIMER_FREQ; - return tbclk; -} diff --git a/arch/arm/include/asm/arch-mb86r0x/hardware.h b/arch/arm/include/asm/arch-mb86r0x/hardware.h deleted file mode 100644 index 42a52bc..0000000 --- a/arch/arm/include/asm/arch-mb86r0x/hardware.h +++ /dev/null @@ -1,15 +0,0 @@ -/* - * (C) Copyright 2007 - * - * Author : Carsten Schneider, mycable GmbH - * - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __ASM_ARCH_HARDWARE_H -#define __ASM_ARCH_HARDWARE_H - -#include -#include - -#endif diff --git a/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h b/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h deleted file mode 100644 index 7fec971..0000000 --- a/arch/arm/include/asm/arch-mb86r0x/mb86r0x.h +++ /dev/null @@ -1,599 +0,0 @@ -/* - * (C) Copyright 2007 - * - * mb86r0x definitions - * - * Author : Carsten Schneider, mycable GmbH - * - * - * (C) Copyright 2010 - * Matthias Weisser - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef MB86R0X_H -#define MB86R0X_H - -#ifndef __ASSEMBLY__ - -/* GPIO registers */ -struct mb86r0x_gpio { - uint32_t gpdr0; - uint32_t gpdr1; - uint32_t gpdr2; - uint32_t res; - uint32_t gpddr0; - uint32_t gpddr1; - uint32_t gpddr2; -}; - -/* PWM registers */ -struct mb86r0x_pwm { - uint32_t bcr; - uint32_t tpr; - uint32_t pr; - uint32_t dr; - uint32_t cr; - uint32_t sr; - uint32_t ccr; - uint32_t ir; -}; - -/* The mb86r0x chip control (CCNT) register set. */ -struct mb86r0x_ccnt { - uint32_t ccid; - uint32_t csrst; - uint32_t pad0[2]; - uint32_t cist; - uint32_t cistm; - uint32_t cgpio_ist; - uint32_t cgpio_istm; - uint32_t cgpio_ip; - uint32_t cgpio_im; - uint32_t caxi_bw; - uint32_t caxi_ps; - uint32_t cmux_md; - uint32_t cex_pin_st; - uint32_t cmlb; - uint32_t pad1[1]; - uint32_t cusb; - uint32_t pad2[41]; - uint32_t cbsc; - uint32_t cdcrc; - uint32_t cmsr0; - uint32_t cmsr1; - uint32_t pad3[2]; -}; - -/* The mb86r0x clock reset generator */ -struct mb86r0x_crg { - uint32_t crpr; - uint32_t pad0; - uint32_t crwr; - uint32_t crsr; - uint32_t crda; - uint32_t crdb; - uint32_t crha; - uint32_t crpa; - uint32_t crpb; - uint32_t crhb; - uint32_t cram; -}; - -/* The mb86r0x timer */ -struct mb86r0x_timer { - uint32_t load; - uint32_t value; - uint32_t control; - uint32_t intclr; - uint32_t ris; - uint32_t mis; - uint32_t bgload; -}; - -/* mb86r0x gdc display controller */ -struct mb86r0x_gdc_dsp { - /* Display settings */ - uint32_t dcm0; - uint16_t pad00; - uint16_t htp; - uint16_t hdp; - uint16_t hdb; - uint16_t hsp; - uint8_t hsw; - uint8_t vsw; - uint16_t pad01; - uint16_t vtr; - uint16_t vsp; - uint16_t vdp; - uint16_t wx; - uint16_t wy; - uint16_t ww; - uint16_t wh; - - /* Layer 0 */ - uint32_t l0m; - uint32_t l0oa; - uint32_t l0da; - uint16_t l0dx; - uint16_t l0dy; - - /* Layer 1 */ - uint32_t l1m; - uint32_t cbda0; - uint32_t cbda1; - uint32_t pad02; - - /* Layer 2 */ - uint32_t l2m; - uint32_t l2oa0; - uint32_t l2da0; - uint32_t l2oa1; - uint32_t l2da1; - uint16_t l2dx; - uint16_t l2dy; - - /* Layer 3 */ - uint32_t l3m; - uint32_t l3oa0; - uint32_t l3da0; - uint32_t l3oa1; - uint32_t l3da1; - uint16_t l3dx; - uint16_t l3dy; - - /* Layer 4 */ - uint32_t l4m; - uint32_t l4oa0; - uint32_t l4da0; - uint32_t l4oa1; - uint32_t l4da1; - uint16_t l4dx; - uint16_t l4dy; - - /* Layer 5 */ - uint32_t l5m; - uint32_t l5oa0; - uint32_t l5da0; - uint32_t l5oa1; - uint32_t l5da1; - uint16_t l5dx; - uint16_t l5dy; - - /* Cursor */ - uint16_t cutc; - uint8_t cpm; - uint8_t csize; - uint32_t cuoa0; - uint16_t cux0; - uint16_t cuy0; - uint32_t cuoa1; - uint16_t cux1; - uint16_t cuy1; - - /* Layer blending */ - uint32_t l0bld; - uint32_t pad03; - uint32_t l0tc; - uint16_t l3tc; - uint16_t l2tc; - uint32_t pad04[15]; - - /* Display settings */ - uint32_t dcm1; - uint32_t dcm2; - uint32_t dcm3; - uint32_t pad05; - - /* Layer 0 extended */ - uint32_t l0em; - uint16_t l0wx; - uint16_t l0wy; - uint16_t l0ww; - uint16_t l0wh; - uint32_t pad06; - - /* Layer 1 extended */ - uint32_t l1em; - uint16_t l1wx; - uint16_t l1wy; - uint16_t l1ww; - uint16_t l1wh; - uint32_t pad07; - - /* Layer 2 extended */ - uint32_t l2em; - uint16_t l2wx; - uint16_t l2wy; - uint16_t l2ww; - uint16_t l2wh; - uint32_t pad08; - - /* Layer 3 extended */ - uint32_t l3em; - uint16_t l3wx; - uint16_t l3wy; - uint16_t l3ww; - uint16_t l3wh; - uint32_t pad09; - - /* Layer 4 extended */ - uint32_t l4em; - uint16_t l4wx; - uint16_t l4wy; - uint16_t l4ww; - uint16_t l4wh; - uint32_t pad10; - - /* Layer 5 extended */ - uint32_t l5em; - uint16_t l5wx; - uint16_t l5wy; - uint16_t l5ww; - uint16_t l5wh; - uint32_t pad11; - - /* Multi screen control */ - uint32_t msc; - uint32_t pad12[3]; - uint32_t dls; - uint32_t dbgc; - - /* Layer blending */ - uint32_t l1bld; - uint32_t l2bld; - uint32_t l3bld; - uint32_t l4bld; - uint32_t l5bld; - uint32_t pad13; - - /* Extended transparency control */ - uint32_t l0etc; - uint32_t l1etc; - uint32_t l2etc; - uint32_t l3etc; - uint32_t l4etc; - uint32_t l5etc; - uint32_t pad14[10]; - - /* YUV coefficients */ - uint32_t l1ycr0; - uint32_t l1ycr1; - uint32_t l1ycg0; - uint32_t l1ycg1; - uint32_t l1ycb0; - uint32_t l1ycb1; - uint32_t pad15[130]; - - /* Layer palletes */ - uint32_t l0pal[256]; - uint32_t l1pal[256]; - uint32_t pad16[256]; - uint32_t l2pal[256]; - uint32_t l3pal[256]; - uint32_t pad17[256]; - - /* PWM settings */ - uint32_t vpwmm; - uint16_t vpwms; - uint16_t vpwme; - uint32_t vpwmc; - uint32_t pad18[253]; -}; - -/* mb86r0x gdc capture controller */ -struct mb86r0x_gdc_cap { - uint32_t vcm; - uint32_t csc; - uint32_t vcs; - uint32_t pad01; - - uint32_t cbm; - uint32_t cboa; - uint32_t cbla; - uint16_t cihstr; - uint16_t civstr; - uint16_t cihend; - uint16_t civend; - uint32_t pad02; - - uint32_t chp; - uint32_t cvp; - uint32_t pad03[4]; - - uint32_t clpf; - uint32_t pad04; - uint32_t cmss; - uint32_t cmds; - uint32_t pad05[12]; - - uint32_t rgbhc; - uint32_t rgbhen; - uint32_t rgbven; - uint32_t pad06; - uint32_t rgbs; - uint32_t pad07[11]; - - uint32_t rgbcmy; - uint32_t rgbcmcb; - uint32_t rgbcmcr; - uint32_t rgbcmb; - uint32_t pad08[12 + 1984]; -}; - -/* mb86r0x gdc draw */ -struct mb86r0x_gdc_draw { - uint32_t ys; - uint32_t xs; - uint32_t dxdy; - uint32_t xus; - uint32_t dxudy; - uint32_t xls; - uint32_t dxldy; - uint32_t usn; - uint32_t lsn; - uint32_t pad01[7]; - uint32_t rs; - uint32_t drdx; - uint32_t drdy; - uint32_t gs; - uint32_t dgdx; - uint32_t dgdy; - uint32_t bs; - uint32_t dbdx; - uint32_t dbdy; - uint32_t pad02[7]; - uint32_t zs; - uint32_t dzdx; - uint32_t dzdy; - uint32_t pad03[13]; - uint32_t ss; - uint32_t dsdx; - uint32_t dsdy; - uint32_t ts; - uint32_t dtdx; - uint32_t dtdy; - uint32_t qs; - uint32_t dqdx; - uint32_t dqdy; - uint32_t pad04[23]; - uint32_t lpn; - uint32_t lxs; - uint32_t lxde; - uint32_t lys; - uint32_t lyde; - uint32_t lzs; - uint32_t lzde; - uint32_t pad05[13]; - uint32_t pxdc; - uint32_t pydc; - uint32_t pzdc; - uint32_t pad06[25]; - uint32_t rxs; - uint32_t rys; - uint32_t rsizex; - uint32_t rsizey; - uint32_t pad07[12]; - uint32_t saddr; - uint32_t sstride; - uint32_t srx; - uint32_t sry; - uint32_t daddr; - uint32_t dstride; - uint32_t drx; - uint32_t dry; - uint32_t brsizex; - uint32_t brsizey; - uint32_t tcolor; - uint32_t pad08[93]; - uint32_t blpo; - uint32_t pad09[7]; - uint32_t ctr; - uint32_t ifsr; - uint32_t ifcnt; - uint32_t sst; - uint32_t ds; - uint32_t pst; - uint32_t est; - uint32_t pad10; - uint32_t mdr0; - uint32_t mdr1; - uint32_t mdr2; - uint32_t mdr3; - uint32_t mdr4; - uint32_t pad14[2]; - uint32_t mdr7; - uint32_t fbr; - uint32_t xres; - uint32_t zbr; - uint32_t tbr; - uint32_t pfbr; - uint32_t cxmin; - uint32_t cxmax; - uint32_t cymin; - uint32_t cymax; - uint32_t txs; - uint32_t tis; - uint32_t toa; - uint32_t sho; - uint32_t abr; - uint32_t pad15[2]; - uint32_t fc; - uint32_t bc; - uint32_t alf; - uint32_t blp; - uint32_t pad16; - uint32_t tbc; - uint32_t pad11[42]; - uint32_t lx0dc; - uint32_t ly0dc; - uint32_t lx1dc; - uint32_t ly1dc; - uint32_t pad12[12]; - uint32_t x0dc; - uint32_t y0dc; - uint32_t x1dc; - uint32_t y1dc; - uint32_t x2dc; - uint32_t y2dc; - uint32_t pad13[666]; -}; - -/* mb86r0x gdc geometry engine */ -struct mb86r0x_gdc_geom { - uint32_t gctr; - uint32_t pad00[15]; - uint32_t gmdr0; - uint32_t gmdr1; - uint32_t gmdr2; - uint32_t pad01[237]; - uint32_t dfifog; - uint32_t pad02[767]; -}; - -/* mb86r0x gdc */ -struct mb86r0x_gdc { - uint32_t pad00[2]; - uint32_t lts; - uint32_t pad01; - uint32_t lsta; - uint32_t pad02[3]; - uint32_t ist; - uint32_t imask; - uint32_t pad03[6]; - uint32_t lsa; - uint32_t lco; - uint32_t lreq; - - uint32_t pad04[16*1024 - 19]; - struct mb86r0x_gdc_dsp dsp0; - struct mb86r0x_gdc_dsp dsp1; - uint32_t pad05[4*1024 - 2]; - uint32_t vccc; - uint32_t vcsr; - struct mb86r0x_gdc_cap cap0; - struct mb86r0x_gdc_cap cap1; - uint32_t pad06[4*1024]; - uint32_t texture_base[16*1024]; - struct mb86r0x_gdc_draw draw; - uint32_t pad07[7*1024]; - struct mb86r0x_gdc_geom geom; - uint32_t pad08[7*1024]; -}; - -/* mb86r0x ddr2c */ -struct mb86r0x_ddr2c { - uint16_t dric; - uint16_t dric1; - uint16_t dric2; - uint16_t drca; - uint16_t drcm; - uint16_t drcst1; - uint16_t drcst2; - uint16_t drcr; - uint16_t pad00[8]; - uint16_t drcf; - uint16_t pad01[7]; - uint16_t drasr; - uint16_t pad02[15]; - uint16_t drims; - uint16_t pad03[7]; - uint16_t dros; - uint16_t pad04; - uint16_t dribsodt1; - uint16_t dribsocd; - uint16_t dribsocd2; - uint16_t pad05[3]; - uint16_t droaba; - uint16_t pad06[9]; - uint16_t drobs; - uint16_t pad07[5]; - uint16_t drimr1; - uint16_t drimr2; - uint16_t drimr3; - uint16_t drimr4; - uint16_t droisr1; - uint16_t droisr2; -}; - -/* mb86r0x memc */ -struct mb86r0x_memc { - uint32_t mcfmode[8]; - uint32_t mcftim[8]; - uint32_t mcfarea[8]; -}; - -#endif /* __ASSEMBLY__ */ - -/* - * Physical Address Defines - */ -#define MB86R0x_DDR2_BASE 0xf3000000 -#define MB86R0x_GDC_BASE 0xf1fc0000 -#define MB86R0x_CCNT_BASE 0xfff42000 -#define MB86R0x_CAN0_BASE 0xfff54000 -#define MB86R0x_CAN1_BASE 0xfff55000 -#define MB86R0x_I2C0_BASE 0xfff56000 -#define MB86R0x_I2C1_BASE 0xfff57000 -#define MB86R0x_EHCI_BASE 0xfff80000 -#define MB86R0x_OHCI_BASE 0xfff81000 -#define MB86R0x_IRC1_BASE 0xfffb0000 -#define MB86R0x_MEMC_BASE 0xfffc0000 -#define MB86R0x_TIMER_BASE 0xfffe0000 -#define MB86R0x_UART0_BASE 0xfffe1000 -#define MB86R0x_UART1_BASE 0xfffe2000 -#define MB86R0x_IRCE_BASE 0xfffe4000 -#define MB86R0x_CRG_BASE 0xfffe7000 -#define MB86R0x_IRC0_BASE 0xfffe8000 -#define MB86R0x_GPIO_BASE 0xfffe9000 -#define MB86R0x_PWM0_BASE 0xfff41000 -#define MB86R0x_PWM1_BASE 0xfff41100 - -#define MB86R0x_CRSR_SWRSTREQ (1 << 1) - -/* - * Timer register bits - */ -#define MB86R0x_TIMER_ENABLE (1 << 7) -#define MB86R0x_TIMER_MODE_MSK (1 << 6) -#define MB86R0x_TIMER_MODE_FR (0 << 6) -#define MB86R0x_TIMER_MODE_PD (1 << 6) - -#define MB86R0x_TIMER_INT_EN (1 << 5) -#define MB86R0x_TIMER_PRS_MSK (3 << 2) -#define MB86R0x_TIMER_PRS_4S (1 << 2) -#define MB86R0x_TIMER_PRS_8S (1 << 3) -#define MB86R0x_TIMER_SIZE_32 (1 << 1) -#define MB86R0x_TIMER_ONE_SHT (1 << 0) - -/* - * Clock reset generator bits - */ -#define MB86R0x_CRG_CRPR_PLLRDY (1 << 8) -#define MB86R0x_CRG_CRPR_PLLMODE (0x1f << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X49 (0 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X46 (1 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X37 (2 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X20 (3 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X47 (4 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X44 (5 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X36 (6 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X19 (7 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X39 (8 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X38 (9 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X30 (10 << 0) -#define MB86R0x_CRG_CRPR_PLLMODE_X15 (11 << 0) -/* - * DDR2 controller bits - */ -#define MB86R0x_DDR2_DRCI_DRINI (1 << 15) -#define MB86R0x_DDR2_DRCI_CKEN (1 << 14) -#define MB86R0x_DDR2_DRCI_DRCMD (1 << 0) -#define MB86R0x_DDR2_DRCI_CMD (MB86R0x_DDR2_DRCI_DRINI | \ - MB86R0x_DDR2_DRCI_CKEN | \ - MB86R0x_DDR2_DRCI_DRCMD) -#define MB86R0x_DDR2_DRCI_INIT (MB86R0x_DDR2_DRCI_DRINI | \ - MB86R0x_DDR2_DRCI_CKEN) -#define MB86R0x_DDR2_DRCI_NORMAL MB86R0x_DDR2_DRCI_CKEN -#endif /* MB86R0X_H */ diff --git a/arch/arm/lib/asm-offsets.c b/arch/arm/lib/asm-offsets.c index b0c26e5..e5bcaea 100644 --- a/arch/arm/lib/asm-offsets.c +++ b/arch/arm/lib/asm-offsets.c @@ -15,9 +15,6 @@ #include #include -#if defined(CONFIG_MB86R0x) -#include -#endif #if defined(CONFIG_MX25) || defined(CONFIG_MX27) || defined(CONFIG_MX35) \ || defined(CONFIG_MX51) || defined(CONFIG_MX53) #include @@ -27,8 +24,6 @@ int main(void) { /* * TODO : Check if each entry in this file is really necessary. - * - struct mb86r0x_ddr2 - * - struct mb86r0x_memc * - struct esdramc_regs * - struct max_regs * - struct aips_regs @@ -40,47 +35,6 @@ int main(void) * code. Is it better to define the macros directly in headers? */ -#if defined(CONFIG_MB86R0x) - /* ddr2 controller */ - DEFINE(DDR2_DRIC, offsetof(struct mb86r0x_ddr2c, dric)); - DEFINE(DDR2_DRIC1, offsetof(struct mb86r0x_ddr2c, dric1)); - DEFINE(DDR2_DRIC2, offsetof(struct mb86r0x_ddr2c, dric2)); - DEFINE(DDR2_DRCA, offsetof(struct mb86r0x_ddr2c, drca)); - DEFINE(DDR2_DRCM, offsetof(struct mb86r0x_ddr2c, drcm)); - DEFINE(DDR2_DRCST1, offsetof(struct mb86r0x_ddr2c, drcst1)); - DEFINE(DDR2_DRCST2, offsetof(struct mb86r0x_ddr2c, drcst2)); - DEFINE(DDR2_DRCR, offsetof(struct mb86r0x_ddr2c, drcr)); - DEFINE(DDR2_DRCF, offsetof(struct mb86r0x_ddr2c, drcf)); - DEFINE(DDR2_DRASR, offsetof(struct mb86r0x_ddr2c, drasr)); - DEFINE(DDR2_DRIMS, offsetof(struct mb86r0x_ddr2c, drims)); - DEFINE(DDR2_DROS, offsetof(struct mb86r0x_ddr2c, dros)); - DEFINE(DDR2_DRIBSODT1, offsetof(struct mb86r0x_ddr2c, dribsodt1)); - DEFINE(DDR2_DROABA, offsetof(struct mb86r0x_ddr2c, droaba)); - DEFINE(DDR2_DROBS, offsetof(struct mb86r0x_ddr2c, drobs)); - - /* clock reset generator */ - DEFINE(CRG_CRPR, offsetof(struct mb86r0x_crg, crpr)); - DEFINE(CRG_CRHA, offsetof(struct mb86r0x_crg, crha)); - DEFINE(CRG_CRPA, offsetof(struct mb86r0x_crg, crpa)); - DEFINE(CRG_CRPB, offsetof(struct mb86r0x_crg, crpb)); - DEFINE(CRG_CRHB, offsetof(struct mb86r0x_crg, crhb)); - DEFINE(CRG_CRAM, offsetof(struct mb86r0x_crg, cram)); - - /* chip control module */ - DEFINE(CCNT_CDCRC, offsetof(struct mb86r0x_ccnt, cdcrc)); - - /* external bus interface */ - DEFINE(MEMC_MCFMODE0, offsetof(struct mb86r0x_memc, mcfmode[0])); - DEFINE(MEMC_MCFMODE2, offsetof(struct mb86r0x_memc, mcfmode[2])); - DEFINE(MEMC_MCFMODE4, offsetof(struct mb86r0x_memc, mcfmode[4])); - DEFINE(MEMC_MCFTIM0, offsetof(struct mb86r0x_memc, mcftim[0])); - DEFINE(MEMC_MCFTIM2, offsetof(struct mb86r0x_memc, mcftim[2])); - DEFINE(MEMC_MCFTIM4, offsetof(struct mb86r0x_memc, mcftim[4])); - DEFINE(MEMC_MCFAREA0, offsetof(struct mb86r0x_memc, mcfarea[0])); - DEFINE(MEMC_MCFAREA2, offsetof(struct mb86r0x_memc, mcfarea[2])); - DEFINE(MEMC_MCFAREA4, offsetof(struct mb86r0x_memc, mcfarea[4])); -#endif - #if defined(CONFIG_MX25) /* Clock Control Module */ DEFINE(CCM_CCTL, offsetof(struct ccm_regs, cctl)); diff --git a/board/syteco/jadecpu/Kconfig b/board/syteco/jadecpu/Kconfig deleted file mode 100644 index 6e9392e..0000000 --- a/board/syteco/jadecpu/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_JADECPU - -config SYS_BOARD - default "jadecpu" - -config SYS_VENDOR - default "syteco" - -config SYS_SOC - default "mb86r0x" - -config SYS_CONFIG_NAME - default "jadecpu" - -endif diff --git a/board/syteco/jadecpu/MAINTAINERS b/board/syteco/jadecpu/MAINTAINERS deleted file mode 100644 index b53e7ca..0000000 --- a/board/syteco/jadecpu/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -JADECPU BOARD -M: Matthias Weisser -S: Maintained -F: board/syteco/jadecpu/ -F: include/configs/jadecpu.h -F: configs/jadecpu_defconfig diff --git a/board/syteco/jadecpu/Makefile b/board/syteco/jadecpu/Makefile deleted file mode 100644 index 7426436..0000000 --- a/board/syteco/jadecpu/Makefile +++ /dev/null @@ -1,13 +0,0 @@ -# -# (C) Copyright 2003-2008 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# (C) Copyright 2008 -# Stelian Pop -# Lead Tech Design -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y += jadecpu.o -obj-y += lowlevel_init.o diff --git a/board/syteco/jadecpu/jadecpu.c b/board/syteco/jadecpu/jadecpu.c deleted file mode 100644 index 6c60a41..0000000 --- a/board/syteco/jadecpu/jadecpu.c +++ /dev/null @@ -1,160 +0,0 @@ -/* - * (c) 2010 Graf-Syteco, Matthias Weisser - * - * - * (C) Copyright 2007, mycable GmbH - * Carsten Schneider , Alexander Bigga - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -/* - * Miscellaneous platform dependent initialisations - */ -int board_init(void) -{ - struct mb86r0x_ccnt * ccnt = (struct mb86r0x_ccnt *) - MB86R0x_CCNT_BASE; - - /* We select mode 0 for group 2 and mode 1 for group 4 */ - writel(0x00000010, &ccnt->cmux_md); - - gd->flags = 0; - gd->bd->bi_boot_params = PHYS_SDRAM + PHYS_SDRAM_SIZE - 0x10000; - - icache_enable(); - dcache_enable(); - - return 0; -} - -static void setup_display_power(uint32_t pwr_bit, char *pwm_opts, - unsigned long pwm_base) -{ - struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *) - MB86R0x_GPIO_BASE; - struct mb86r0x_pwm *pwm = (struct mb86r0x_pwm *) pwm_base; - const char *e; - - writel(readl(&gpio->gpdr2) | pwr_bit, &gpio->gpdr2); - - e = getenv(pwm_opts); - if (e != NULL) { - const char *s; - uint32_t freq, init; - - freq = 0; - init = 0; - - s = strchr(e, 'f'); - if (s != NULL) - freq = simple_strtol(s + 2, NULL, 0); - - s = strchr(e, 'i'); - if (s != NULL) - init = simple_strtol(s + 2, NULL, 0); - - if (freq > 0) { - writel(CONFIG_MB86R0x_IOCLK / 1000 / freq, - &pwm->bcr); - writel(1002, &pwm->tpr); - writel(1, &pwm->pr); - writel(init * 10 + 1, &pwm->dr); - writel(1, &pwm->cr); - writel(1, &pwm->sr); - } - } -} - -int board_late_init(void) -{ - struct mb86r0x_gpio *gpio = (struct mb86r0x_gpio *) - MB86R0x_GPIO_BASE; - uint32_t in_word; - -#ifdef CONFIG_VIDEO_MB86R0xGDC - /* Check if we have valid display settings and turn on power if so */ - /* Display 0 */ - if (getenv("gs_dsp_0_param") || getenv("videomode")) - setup_display_power((1 << 3), "gs_dsp_0_pwm", - MB86R0x_PWM0_BASE); - - /* The corresponding GPIO is always an output */ - writel(readl(&gpio->gpddr2) | (1 << 3), &gpio->gpddr2); - - /* Display 1 */ - if (getenv("gs_dsp_1_param") || getenv("videomode1")) - setup_display_power((1 << 4), "gs_dsp_1_pwm", - MB86R0x_PWM1_BASE); - - /* The corresponding GPIO is always an output */ - writel(readl(&gpio->gpddr2) | (1 << 4), &gpio->gpddr2); -#endif /* CONFIG_VIDEO_MB86R0xGDC */ - - /* 5V enable */ - writel(readl(&gpio->gpdr1) & ~(1 << 5), &gpio->gpdr1); - writel(readl(&gpio->gpddr1) | (1 << 5), &gpio->gpddr1); - - /* We have special boot options if told by GPIOs */ - in_word = readl(&gpio->gpdr1); - - if ((in_word & 0xC0) == 0xC0) { - setenv("stdin", "serial"); - setenv("stdout", "serial"); - setenv("stderr", "serial"); - setenv("preboot", "run gs_slow_boot"); - } else if ((in_word & 0xC0) != 0) { - setenv("stdout", "vga"); - setenv("preboot", "run gs_slow_boot"); - } else { - setenv("stdin", "serial"); - setenv("stdout", "serial"); - setenv("stderr", "serial"); - if (getenv("gs_devel")) { - setenv("preboot", "run gs_slow_boot"); - } else { - setenv("preboot", "run gs_fast_boot"); - } - } - - return 0; -} - -int misc_init_r(void) -{ - return 0; -} - -/* - * DRAM configuration - */ -int dram_init(void) -{ - /* dram_init must store complete ramsize in gd->ram_size */ - gd->ram_size = get_ram_size((void *)PHYS_SDRAM, - PHYS_SDRAM_SIZE); - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM; - gd->bd->bi_dram[0].size = gd->ram_size; -} - -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_SMC911X - rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); -#endif - return rc; -} diff --git a/board/syteco/jadecpu/lowlevel_init.S b/board/syteco/jadecpu/lowlevel_init.S deleted file mode 100644 index 9568cec..0000000 --- a/board/syteco/jadecpu/lowlevel_init.S +++ /dev/null @@ -1,249 +0,0 @@ -/* - * Board specific setup info - * - * (C) Copyright 2007, mycable GmbH - * Carsten Schneider , Alexander Bigga - * - * (C) Copyright 2003, ARM Ltd. - * Philippe Robin, - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -/* Set up the platform, once the cpu has been initialized */ -.globl lowlevel_init -lowlevel_init: -/* - * Initialize Clock Reset Generator (CRG) - */ - - ldr r0, =MB86R0x_CRG_BASE - - /* Not change the initial value that is set by external pin.*/ -WAIT_PLL: - ldr r2, [r0, #CRG_CRPR] /* Wait for PLLREADY */ - tst r2, #MB86R0x_CRG_CRPR_PLLRDY - beq WAIT_PLL - - /* Set clock gate control */ - ldr r1, =CONFIG_SYS_CRG_CRHA_INIT - str r1, [r0, #CRG_CRHA] - ldr r1, =CONFIG_SYS_CRG_CRPA_INIT - str r1, [r0, #CRG_CRPA] - ldr r1, =CONFIG_SYS_CRG_CRPB_INIT - str r1, [r0, #CRG_CRPB] - ldr r1, =CONFIG_SYS_CRG_CRHB_INIT - str r1, [r0, #CRG_CRHB] - ldr r1, =CONFIG_SYS_CRG_CRAM_INIT - str r1, [r0, #CRG_CRAM] - -/* - * Initialize External Bus Interface - */ - ldr r0, =MB86R0x_MEMC_BASE - - ldr r1, =CONFIG_SYS_MEMC_MCFMODE0_INIT - str r1, [r0, #MEMC_MCFMODE0] - ldr r1, =CONFIG_SYS_MEMC_MCFMODE2_INIT - str r1, [r0, #MEMC_MCFMODE2] - ldr r1, =CONFIG_SYS_MEMC_MCFMODE4_INIT - str r1, [r0, #MEMC_MCFMODE4] - - ldr r1, =CONFIG_SYS_MEMC_MCFTIM0_INIT - str r1, [r0, #MEMC_MCFTIM0] - ldr r1, =CONFIG_SYS_MEMC_MCFTIM2_INIT - str r1, [r0, #MEMC_MCFTIM2] - ldr r1, =CONFIG_SYS_MEMC_MCFTIM4_INIT - str r1, [r0, #MEMC_MCFTIM4] - - ldr r1, =CONFIG_SYS_MEMC_MCFAREA0_INIT - str r1, [r0, #MEMC_MCFAREA0] - ldr r1, =CONFIG_SYS_MEMC_MCFAREA2_INIT - str r1, [r0, #MEMC_MCFAREA2] - ldr r1, =CONFIG_SYS_MEMC_MCFAREA4_INIT - str r1, [r0, #MEMC_MCFAREA4] - -/* - * Initialize DDR2 Controller - */ - - /* Wait for PLL LOCK up time or more */ - wait_timer 20 - - /* - * (2) Initialize DDRIF - */ - ldr r0, =MB86R0x_DDR2_BASE - ldr r1, =CONFIG_SYS_DDR2_DRIMS_INIT - strh r1, [r0, #DDR2_DRIMS] - - /* - * (3) Wait for 20MCKPs(120nsec) or more - */ - wait_timer 20 - - /* - * (4) IRESET/IUSRRST release - */ - ldr r0, =MB86R0x_CCNT_BASE - ldr r1, =CONFIG_SYS_CCNT_CDCRC_INIT_1 - str r1, [r0, #CCNT_CDCRC] - - /* - * (5) Wait for 20MCKPs(120nsec) or more - */ - wait_timer 20 - - /* - * (6) IDLLRST release - */ - ldr r0, =MB86R0x_CCNT_BASE - ldr r1, =CONFIG_SYS_CCNT_CDCRC_INIT_2 - str r1, [r0, #CCNT_CDCRC] - - /* - * (7+8) Wait for 200us(=200000ns) or more (DDR2 Spec) - */ - wait_timer 33536 - - /* - * (9) MCKE ON - */ - ldr r0, =MB86R0x_DDR2_BASE - ldr r1, =CONFIG_SYS_DDR2_DRIC1_INIT - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_DRIC2_INIT - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =CONFIG_SYS_DDR2_DRCA_INIT - strh r1, [r0, #DDR2_DRCA] - ldr r1, =MB86R0x_DDR2_DRCI_INIT - strh r1, [r0, #DDR2_DRIC] - - /* - * (10) Initialize SDRAM - */ - - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - wait_timer 67 /* 400ns wait */ - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_1 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_1 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_2 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_2 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_3 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_3 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_4 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_4 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_5 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_5 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - wait_timer 200 - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_6 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_6 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_7 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_7 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - wait_timer 18 /* 105ns wait */ - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_8 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_8 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - wait_timer 200 /* MRS to OCD: 200clock */ - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_9 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_9 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC1_10 - strh r1, [r0, #DDR2_DRIC1] - ldr r1, =CONFIG_SYS_DDR2_INIT_DRIC2_10 - strh r1, [r0, #DDR2_DRIC2] - ldr r1, =MB86R0x_DDR2_DRCI_CMD - strh r1, [r0, #DDR2_DRIC] - - ldr r1, =CONFIG_SYS_DDR2_DRCM_INIT - strh r1, [r0, #DDR2_DRCM] - - ldr r1, =CONFIG_SYS_DDR2_DRCST1_INIT - strh r1, [r0, #DDR2_DRCST1] - - ldr r1, =CONFIG_SYS_DDR2_DRCST2_INIT - strh r1, [r0, #DDR2_DRCST2] - - ldr r1, =CONFIG_SYS_DDR2_DRCR_INIT - strh r1, [r0, #DDR2_DRCR] - - ldr r1, =CONFIG_SYS_DDR2_DRCF_INIT - strh r1, [r0, #DDR2_DRCF] - - ldr r1, =CONFIG_SYS_DDR2_DRASR_INIT - strh r1, [r0, #DDR2_DRASR] - - /* - * (11) ODT setting - */ - ldr r1, =CONFIG_SYS_DDR2_DROBS_INIT - strh r1, [r0, #DDR2_DROBS] - ldr r1, =CONFIG_SYS_DDR2_DROABA_INIT - strh r1, [r0, #DDR2_DROABA] - ldr r1, =CONFIG_SYS_DDR2_DRIBSODT1_INIT - strh r1, [r0, #DDR2_DRIBSODT1] - - /* - * (12) Shift to ODTCONT ON (SDRAM side) and DDR2 usual operation mode - */ - ldr r1, =CONFIG_SYS_DDR2_DROS_INIT - strh r1, [r0, #DDR2_DROS] - ldr r1, =MB86R0x_DDR2_DRCI_NORMAL - strh r1, [r0, #DDR2_DRIC] - - mov pc, lr diff --git a/configs/jadecpu_defconfig b/configs/jadecpu_defconfig deleted file mode 100644 index 4348e0e..0000000 --- a/configs/jadecpu_defconfig +++ /dev/null @@ -1,2 +0,0 @@ -CONFIG_ARM=y -CONFIG_TARGET_JADECPU=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 952ab87..0fc6ac7 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,23 +12,24 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= -icecube_5200 powerpc mpc5xxx - - Wolfgang Denk -Lite5200 powerpc mpc5xxx - - -cpci5200 powerpc mpc5xxx - - Reinhard Arlt -mecp5200 powerpc mpc5xxx - - Reinhard Arlt -pf5200 powerpc mpc5xxx - - Reinhard Arlt -PM520 powerpc mpc5xxx - - Josef Wagner -Total5200 powerpc mpc5xxx - - -CATcenter powerpc ppc4xx - - -PPChameleonEVB powerpc ppc4xx - - Andrea "llandre" Marson -P2020DS powerpc mpc85xx - - -P2020COME powerpc mpc85xx - - Ira W. Snyder -P2020RDB powerpc mpc85xx - - Poonam Aggrwal -P2010RDB powerpc mpc85xx - - -P1020RDB powerpc mpc85xx - - -P1011RDB powerpc mpc85xx - - -MPC8360EMDS powerpc mpc83xx - - Dave Liu -MPC8360ERDK powerpc mpc83xx - - Anton Vorontsov +jadecpu arm arm926ejs - - Matthias Weisser +icecube_5200 powerpc mpc5xxx 37b608a5 2015-01-23 Wolfgang Denk +Lite5200 powerpc mpc5xxx 37b608a5 2015-01-23 +cpci5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt +mecp5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt +pf5200 powerpc mpc5xxx 37b608a5 2015-01-23 Reinhard Arlt +PM520 powerpc mpc5xxx a258e732 2015-01-23 Josef Wagner +Total5200 powerpc mpc5xxx ad734f7d 2015-01-23 +CATcenter powerpc ppc4xx 5344cc1a 2015-01-23 +PPChameleonEVB powerpc ppc4xx 5344cc1a 2015-01-23 Andrea "llandre" Marson +P2020DS powerpc mpc85xx 168dcc6c 2015-01-23 +P2020COME powerpc mpc85xx 89123536 2015-01-23 Ira W. Snyder +P2020RDB powerpc mpc85xx 743d4815 2015-01-23 Poonam Aggrwal +P2010RDB powerpc mpc85xx 743d4815 2015-01-23 +P1020RDB powerpc mpc85xx 743d4815 2015-01-23 +P1011RDB powerpc mpc85xx 743d4815 2015-01-23 +MPC8360EMDS powerpc mpc83xx 8d1e3cb1 2015-01-23 Dave Liu +MPC8360ERDK powerpc mpc83xx 8d1e3cb1 2015-01-23 Anton Vorontsov P3G4 powerpc 74xx_7xx d928664f 2015-01-16 Wolfgang Denk ZUMA powerpc 74xx_7xx d928664f 2015-01-16 Nye Liu ppmc7xx powerpc 74xx_7xx d928664f 2015-01-16 diff --git a/drivers/video/Makefile b/drivers/video/Makefile index af2d47b..22a316b 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -32,7 +32,6 @@ obj-$(CONFIG_VIDEO_IMX25LCDC) += imx25lcdc.o videomodes.o obj-$(CONFIG_VIDEO_LCD_HITACHI_TX18D42VM) += hitachi_tx18d42vm_lcd.o obj-$(CONFIG_VIDEO_LCD_SSD2828) += ssd2828.o obj-$(CONFIG_VIDEO_MB862xx) += mb862xx.o videomodes.o -obj-$(CONFIG_VIDEO_MB86R0xGDC) += mb86r0xgdc.o videomodes.o obj-$(CONFIG_VIDEO_MX3) += mx3fb.o videomodes.o obj-$(CONFIG_VIDEO_IPUV3) += mxc_ipuv3_fb.o ipu_common.o ipu_disp.o obj-$(CONFIG_VIDEO_MXS) += mxsfb.o videomodes.o diff --git a/drivers/video/mb86r0xgdc.c b/drivers/video/mb86r0xgdc.c deleted file mode 100644 index bb7a749..0000000 --- a/drivers/video/mb86r0xgdc.c +++ /dev/null @@ -1,168 +0,0 @@ -/* - * (C) Copyright 2010 - * Matthias Weisser - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * mb86r0xgdc.c - Graphic interface for Fujitsu MB86R0x integrated graphic - * controller. - */ - -#include - -#include -#include -#include -#include -#include "videomodes.h" - -/* - * 4MB (at the end of system RAM) - */ -#define VIDEO_MEM_SIZE 0x400000 - -#define FB_SYNC_CLK_INV (1<<16) /* pixel clock inverted */ - -/* - * Graphic Device - */ -static GraphicDevice mb86r0x; - -static void dsp_init(struct mb86r0x_gdc_dsp *dsp, char *modestr, - u32 *videomem) -{ - struct ctfb_res_modes var_mode; - u32 dcm1, dcm2, dcm3; - u16 htp, hdp, hdb, hsp, vtr, vsp, vdp; - u8 hsw, vsw; - u32 l2m, l2em, l2oa0, l2da0, l2oa1, l2da1; - u16 l2dx, l2dy, l2wx, l2wy, l2ww, l2wh; - unsigned long div; - int bpp; - - bpp = video_get_params(&var_mode, modestr); - - if (bpp == 0) { - var_mode.xres = 640; - var_mode.yres = 480; - var_mode.pixclock = 39721; /* 25MHz */ - var_mode.left_margin = 48; - var_mode.right_margin = 16; - var_mode.upper_margin = 33; - var_mode.lower_margin = 10; - var_mode.hsync_len = 96; - var_mode.vsync_len = 2; - var_mode.sync = 0; - var_mode.vmode = 0; - bpp = 15; - } - - /* Fill memory with white */ - memset(videomem, 0xFF, var_mode.xres * var_mode.yres * 2); - - mb86r0x.winSizeX = var_mode.xres; - mb86r0x.winSizeY = var_mode.yres; - - /* LCD base clock is ~ 660MHZ. We do calculations in kHz */ - div = 660000 / (1000000000L / var_mode.pixclock); - if (div > 64) - div = 64; - if (0 == div) - div = 1; - - dcm1 = (div - 1) << 8; - dcm2 = 0x00000000; - if (var_mode.sync & FB_SYNC_CLK_INV) - dcm3 = 0x00000100; - else - dcm3 = 0x00000000; - - htp = var_mode.left_margin + var_mode.xres + - var_mode.hsync_len + var_mode.right_margin; - hdp = var_mode.xres; - hdb = var_mode.xres; - hsp = var_mode.xres + var_mode.right_margin; - hsw = var_mode.hsync_len; - - vsw = var_mode.vsync_len; - vtr = var_mode.upper_margin + var_mode.yres + - var_mode.vsync_len + var_mode.lower_margin; - vsp = var_mode.yres + var_mode.lower_margin; - vdp = var_mode.yres; - - l2m = ((var_mode.yres - 1) << (0)) | - (((var_mode.xres * 2) / 64) << (16)) | - ((1) << (31)); - - l2em = (1 << 0) | (1 << 1); - - l2oa0 = mb86r0x.frameAdrs; - l2da0 = mb86r0x.frameAdrs; - l2oa1 = mb86r0x.frameAdrs; - l2da1 = mb86r0x.frameAdrs; - l2dx = 0; - l2dy = 0; - l2wx = 0; - l2wy = 0; - l2ww = var_mode.xres; - l2wh = var_mode.yres - 1; - - writel(dcm1, &dsp->dcm1); - writel(dcm2, &dsp->dcm2); - writel(dcm3, &dsp->dcm3); - - writew(htp, &dsp->htp); - writew(hdp, &dsp->hdp); - writew(hdb, &dsp->hdb); - writew(hsp, &dsp->hsp); - writeb(hsw, &dsp->hsw); - - writeb(vsw, &dsp->vsw); - writew(vtr, &dsp->vtr); - writew(vsp, &dsp->vsp); - writew(vdp, &dsp->vdp); - - writel(l2m, &dsp->l2m); - writel(l2em, &dsp->l2em); - writel(l2oa0, &dsp->l2oa0); - writel(l2da0, &dsp->l2da0); - writel(l2oa1, &dsp->l2oa1); - writel(l2da1, &dsp->l2da1); - writew(l2dx, &dsp->l2dx); - writew(l2dy, &dsp->l2dy); - writew(l2wx, &dsp->l2wx); - writew(l2wy, &dsp->l2wy); - writew(l2ww, &dsp->l2ww); - writew(l2wh, &dsp->l2wh); - - writel(dcm1 | (1 << 18) | (1 << 31), &dsp->dcm1); -} - -void *video_hw_init(void) -{ - struct mb86r0x_gdc *gdc = (struct mb86r0x_gdc *) MB86R0x_GDC_BASE; - GraphicDevice *pGD = &mb86r0x; - char *s; - u32 *vid; - - memset(pGD, 0, sizeof(GraphicDevice)); - - pGD->gdfIndex = GDF_15BIT_555RGB; - pGD->gdfBytesPP = 2; - pGD->memSize = VIDEO_MEM_SIZE; - pGD->frameAdrs = PHYS_SDRAM + PHYS_SDRAM_SIZE - VIDEO_MEM_SIZE; - - vid = (u32 *)pGD->frameAdrs; - - s = getenv("videomode"); - if (s != NULL) - dsp_init(&gdc->dsp0, s, vid); - - s = getenv("videomode1"); - if (s != NULL) - dsp_init(&gdc->dsp1, s, vid); - - return pGD; -} diff --git a/include/configs/jadecpu.h b/include/configs/jadecpu.h deleted file mode 100644 index 8175621..0000000 --- a/include/configs/jadecpu.h +++ /dev/null @@ -1,273 +0,0 @@ -/* - * (C) Copyright 2010 - * Matthias Weisser - * - * Configuation settings for the jadecpu board - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_MB86R0x -#define CONFIG_MB86R0x_IOCLK get_bus_freq(0) -#define CONFIG_SYS_TEXT_BASE 0x10000000 - - -#define CONFIG_USE_ARCH_MEMCPY -#define CONFIG_USE_ARCH_MEMSET - -#define MACH_TYPE_JADECPU 2636 - -#define CONFIG_MACH_TYPE MACH_TYPE_JADECPU - -/* - * Environment settings - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "gs_fast_boot=setenv bootdelay 5\0" \ - "gs_slow_boot=setenv bootdelay 10\0" \ - "bootcmd=dcache off; mw.l 0x40000000 0 1024; usb start;" \ - "fatls usb 0; fatload usb 0 0x40000000 jadecpu-init.bin;" \ - "bootelf 0x40000000\0" \ - "" - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_BOARD_LATE_INIT - -/* - * Compressions - */ -#define CONFIG_LZO - -/* - * Hardware drivers - */ - -/* - * Serial - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CONFIG_SYS_NS16550_COM1 0xfffe1000 /* UART 0 */ -#define CONFIG_SYS_NS16550_COM2 0xfff50000 /* UART 2 */ -#define CONFIG_SYS_NS16550_COM3 0xfff51000 /* UART 3 */ -#define CONFIG_SYS_NS16550_COM4 0xfff43000 /* UART 4 */ - -#define CONFIG_CONS_INDEX 4 - -/* - * Ethernet - */ -#define CONFIG_SMC911X -#define CONFIG_SMC911X_BASE 0x02000000 -#define CONFIG_SMC911X_16_BIT - -/* - * Video - */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_MB86R0xGDC -#define CONFIG_SYS_WHITE_ON_BLACK -#define CONFIG_CFB_CONSOLE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE -#define CONFIG_VIDEO_LOGO -#define CONFIG_SPLASH_SCREEN -#define CONFIG_SPLASH_SCREEN_ALIGN -#define CONFIG_VIDEO_BMP_LOGO -#define CONFIG_VIDEO_BMP_GZIP -#define CONFIG_VIDEO_BMP_RLE8 -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (800*480 + 256*4 + 10*1024) -#define VIDEO_FB_16BPP_WORD_SWAP -#define VIDEO_KBD_INIT_FCT 0 -#define VIDEO_TSTC_FCT serial_stub_tstc -#define VIDEO_GETC_FCT serial_stub_getc - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE 1 -#define CONFIG_BOOTP_BOOTPATH 1 -#define CONFIG_BOOTP_GATEWAY 1 -#define CONFIG_BOOTP_HOSTNAME 1 - -/* - * Command line configuration. - */ -#include -#undef CONFIG_CMD_BDI -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_IMLS -#undef CONFIG_CMD_LOADS -#undef CONFIG_CMD_SOURCE -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_XIMG - -#define CONFIG_CMD_BMP -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_PING -#define CONFIG_CMD_USB -#define CONFIG_CMD_CACHE - -#define CONFIG_SYS_HUSH_PARSER - -/* USB */ -#define CONFIG_USB_OHCI_NEW -#define CONFIG_SYS_USB_OHCI_REGS_BASE 0xFFF81000 -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mb86r0x" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1 -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION - -/* SDRAM */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM 0x40000000 /* Start address of DDRRAM */ -#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */ - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM -#define CONFIG_SYS_INIT_SP_ADDR 0x01008000 - -/* - * FLASH and environment organization - */ -#define CONFIG_SYS_FLASH_BASE 0x10000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 256 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE - -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000) -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE (128 * 1024) - -/* - * CFI FLASH driver setup - */ -#define CONFIG_SYS_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* ~10x faster */ - -#define CONFIG_SYS_LOAD_ADDR 0x40000000 /* load address */ - -#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM + (512*1024)) -#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM + PHYS_SDRAM_SIZE) - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_PROMPT "jade> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 - -#define CONFIG_PREBOOT "" - -#define CONFIG_BOOTDELAY 5 -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT "boot in %d s\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "delaygs" -#define CONFIG_AUTOBOOT_STOP_STR "stopgs" - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (10 << 20) -#define CONFIG_SYS_MEM_TOP_HIDE (4 << 20) - -/* - * Clock reset generator init - */ -#define CONFIG_SYS_CRG_CRHA_INIT 0xffff -#define CONFIG_SYS_CRG_CRPA_INIT 0xffff -#define CONFIG_SYS_CRG_CRPB_INIT 0xfffe -#define CONFIG_SYS_CRG_CRHB_INIT 0xffff -#define CONFIG_SYS_CRG_CRAM_INIT 0xffef - -/* - * Memory controller settings - */ -#define CONFIG_SYS_MEMC_MCFMODE0_INIT 0x00000001 /* 16bit */ -#define CONFIG_SYS_MEMC_MCFMODE2_INIT 0x00000001 /* 16bit */ -#define CONFIG_SYS_MEMC_MCFMODE4_INIT 0x00000021 /* 16bit, Page*/ -#define CONFIG_SYS_MEMC_MCFTIM0_INIT 0x16191008 -#define CONFIG_SYS_MEMC_MCFTIM2_INIT 0x03061008 -#define CONFIG_SYS_MEMC_MCFTIM4_INIT 0x03061804 -#define CONFIG_SYS_MEMC_MCFAREA0_INIT 0x000000c0 /* 0x0c000000 1MB */ -#define CONFIG_SYS_MEMC_MCFAREA2_INIT 0x00000020 /* 0x02000000 1MB */ -#define CONFIG_SYS_MEMC_MCFAREA4_INIT 0x001f0000 /* 0x10000000 32 MB */ - -/* - * DDR2 controller init settings - */ -#define CONFIG_SYS_DDR2_DRIMS_INIT 0x5555 -#define CONFIG_SYS_CCNT_CDCRC_INIT_1 0x00000002 -#define CONFIG_SYS_CCNT_CDCRC_INIT_2 0x00000003 -#define CONFIG_SYS_DDR2_DRIC1_INIT 0x003f -#define CONFIG_SYS_DDR2_DRIC2_INIT 0x0000 -#define CONFIG_SYS_DDR2_DRCA_INIT 0xc124 /* 512Mbit DDR2SDRAM x 2 */ -#define CONFIG_SYS_DDR2_DRCM_INIT 0x0032 -#define CONFIG_SYS_DDR2_DRCST1_INIT 0x3418 -#define CONFIG_SYS_DDR2_DRCST2_INIT 0x6e32 -#define CONFIG_SYS_DDR2_DRCR_INIT 0x0141 -#define CONFIG_SYS_DDR2_DRCF_INIT 0x0002 -#define CONFIG_SYS_DDR2_DRASR_INIT 0x0001 -#define CONFIG_SYS_DDR2_DROBS_INIT 0x0001 -#define CONFIG_SYS_DDR2_DROABA_INIT 0x0103 -#define CONFIG_SYS_DDR2_DRIBSODT1_INIT 0x003F -#define CONFIG_SYS_DDR2_DROS_INIT 0x0001 - -/* - * DRAM init sequence - */ - -/* PALL Command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_1 0x0017 -#define CONFIG_SYS_DDR2_INIT_DRIC2_1 0x0400 - -/* EMR(2) command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_2 0x0006 -#define CONFIG_SYS_DDR2_INIT_DRIC2_2 0x0000 - -/* EMR(3) command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_3 0x0007 -#define CONFIG_SYS_DDR2_INIT_DRIC2_3 0x0000 - -/* EMR(1) command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_4 0x0005 -#define CONFIG_SYS_DDR2_INIT_DRIC2_4 0x0000 - -/* MRS command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_5 0x0004 -#define CONFIG_SYS_DDR2_INIT_DRIC2_5 0x0532 - -/* PALL command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_6 0x0017 -#define CONFIG_SYS_DDR2_INIT_DRIC2_6 0x0400 - -/* REF command 1 */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_7 0x000f -#define CONFIG_SYS_DDR2_INIT_DRIC2_7 0x0000 - -/* MRS command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_8 0x0004 -#define CONFIG_SYS_DDR2_INIT_DRIC2_8 0x0432 - -/* EMR(1) command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_9 0x0005 -#define CONFIG_SYS_DDR2_INIT_DRIC2_9 0x0380 - -/* EMR(1) command */ -#define CONFIG_SYS_DDR2_INIT_DRIC1_10 0x0005 -#define CONFIG_SYS_DDR2_INIT_DRIC2_10 0x0002 - -#endif /* __CONFIG_H */ diff --git a/include/serial.h b/include/serial.h index 66ed12c..3d2e569 100644 --- a/include/serial.h +++ b/include/serial.h @@ -29,7 +29,7 @@ extern struct serial_device *default_serial_console(void); #if defined(CONFIG_405GP) || \ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ defined(CONFIG_405EX) || defined(CONFIG_440) || \ - defined(CONFIG_MB86R0x) || defined(CONFIG_MPC5xxx) || \ + defined(CONFIG_MPC5xxx) || \ defined(CONFIG_MPC83xx) || defined(CONFIG_MPC85xx) || \ defined(CONFIG_MPC86xx) || defined(CONFIG_SYS_SC520) || \ defined(CONFIG_TEGRA) || defined(CONFIG_SYS_COREBOOT) || \ -- cgit v0.10.2