From c5330ae8c8169fa9e81e2f8f5db4a9388d0a89d6 Mon Sep 17 00:00:00 2001 From: Konstantin Porotchkin Date: Thu, 16 Feb 2017 13:52:22 +0200 Subject: arm64: mvebu: Rename the db-88f3720 to armada-37xx platform Modify the file names and deifinitions relater to Marvell db-77f3720 board support. Convert these names to more generic armada-37xx platform for future addition of more boards based on the same SoC family. Signed-off-by: Konstantin Porotchkin Cc: Stefan Roese Cc: Igal Liberman Cc: Nadav Haklai Signed-off-by: Stefan Roese diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 412bda4..a256c2f 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -74,8 +74,8 @@ config TARGET_CLEARFOG bool "Support ClearFog" select 88F6820 -config TARGET_MVEBU_DB_88F3720 - bool "Support DB-88F3720 Armada 3720" +config TARGET_MVEBU_ARMADA_37XX + bool "Support Armada 37xx platforms" select ARMADA_3700 config TARGET_DB_88F6720 @@ -116,7 +116,7 @@ endchoice config SYS_BOARD default "clearfog" if TARGET_CLEARFOG - default "mvebu_db-88f3720" if TARGET_MVEBU_DB_88F3720 + default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX default "db-88f6720" if TARGET_DB_88F6720 default "db-88f6820-gp" if TARGET_DB_88F6820_GP default "db-88f6820-amc" if TARGET_DB_88F6820_AMC @@ -128,7 +128,7 @@ config SYS_BOARD config SYS_CONFIG_NAME default "clearfog" if TARGET_CLEARFOG - default "mvebu_db-88f3720" if TARGET_MVEBU_DB_88F3720 + default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX default "db-88f6720" if TARGET_DB_88F6720 default "db-88f6820-gp" if TARGET_DB_88F6820_GP default "db-88f6820-amc" if TARGET_DB_88F6820_AMC @@ -140,7 +140,7 @@ config SYS_CONFIG_NAME config SYS_VENDOR default "Marvell" if TARGET_DB_MV784MP_GP - default "Marvell" if TARGET_MVEBU_DB_88F3720 + default "Marvell" if TARGET_MVEBU_ARMADA_37XX default "Marvell" if TARGET_DB_88F6720 default "Marvell" if TARGET_DB_88F6820_GP default "Marvell" if TARGET_DB_88F6820_AMC diff --git a/board/Marvell/mvebu_armada-37xx/MAINTAINERS b/board/Marvell/mvebu_armada-37xx/MAINTAINERS new file mode 100644 index 0000000..52a3869 --- /dev/null +++ b/board/Marvell/mvebu_armada-37xx/MAINTAINERS @@ -0,0 +1,6 @@ +MVEBU_DB_88F3720 BOARD +M: Stefan Roese +S: Maintained +F: board/Marvell/mvebu_armada-37xx/ +F: include/configs/mvebu_armada-37xx.h +F: configs/mvebu_db-88f3720_defconfig diff --git a/board/Marvell/mvebu_armada-37xx/Makefile b/board/Marvell/mvebu_armada-37xx/Makefile new file mode 100644 index 0000000..ed39738 --- /dev/null +++ b/board/Marvell/mvebu_armada-37xx/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (C) 2016 Stefan Roese +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := board.o diff --git a/board/Marvell/mvebu_armada-37xx/board.c b/board/Marvell/mvebu_armada-37xx/board.c new file mode 100644 index 0000000..edf88c7 --- /dev/null +++ b/board/Marvell/mvebu_armada-37xx/board.c @@ -0,0 +1,134 @@ +/* + * Copyright (C) 2016 Stefan Roese + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +/* IO expander I2C device */ +#define I2C_IO_EXP_ADDR 0x22 +#define I2C_IO_CFG_REG_0 0x6 +#define I2C_IO_DATA_OUT_REG_0 0x2 +#define I2C_IO_REG_0_SATA_OFF 2 +#define I2C_IO_REG_0_USB_H_OFF 1 + +int board_early_init_f(void) +{ + /* Nothing to do (yet), perhaps later some pin-muxing etc */ + + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + return 0; +} + +/* Board specific AHCI / SATA enable code */ +int board_ahci_enable(void) +{ + struct udevice *dev; + int ret; + u8 buf[8]; + + /* Configure IO exander PCA9555: 7bit address 0x22 */ + ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev); + if (ret) { + printf("Cannot find PCA9555: %d\n", ret); + return 0; + } + + ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1); + if (ret) { + printf("Failed to read IO expander value via I2C\n"); + return -EIO; + } + + /* + * Enable SATA power via IO expander connected via I2C by setting + * the corresponding bit to output mode to enable power for SATA + */ + buf[0] &= ~(1 << I2C_IO_REG_0_SATA_OFF); + ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + + return 0; +} + +/* Board specific xHCI enable code */ +int board_xhci_enable(void) +{ + struct udevice *dev; + int ret; + u8 buf[8]; + + /* Configure IO exander PCA9555: 7bit address 0x22 */ + ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev); + if (ret) { + printf("Cannot find PCA9555: %d\n", ret); + return 0; + } + + printf("Enable USB VBUS\n"); + + /* + * Read configuration (direction) and set VBUS pin as output + * (reset pin = output) + */ + ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1); + if (ret) { + printf("Failed to read IO expander value via I2C\n"); + return -EIO; + } + buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF); + ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + + /* Read VBUS output value and disable it */ + ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); + if (ret) { + printf("Failed to read IO expander value via I2C\n"); + return -EIO; + } + buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF); + ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + + /* + * Required delay for configuration to settle - must wait for + * power on port is disabled in case VBUS signal was high, + * required 3 seconds delay to let VBUS signal fully settle down + */ + mdelay(3000); + + /* Enable VBUS power: Set output value of VBUS pin as enabled */ + buf[0] |= (1 << I2C_IO_REG_0_USB_H_OFF); + ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + + mdelay(500); /* required delay to let output value settle */ + + return 0; +} diff --git a/board/Marvell/mvebu_db-88f3720/MAINTAINERS b/board/Marvell/mvebu_db-88f3720/MAINTAINERS deleted file mode 100644 index 4e80917..0000000 --- a/board/Marvell/mvebu_db-88f3720/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MVEBU_DB_88F3720 BOARD -M: Stefan Roese -S: Maintained -F: board/Marvell/mvebu_db-88f3720/ -F: include/configs/mvebu_db-88f3720.h -F: configs/mvebu_db-88f3720_defconfig diff --git a/board/Marvell/mvebu_db-88f3720/Makefile b/board/Marvell/mvebu_db-88f3720/Makefile deleted file mode 100644 index ed39738..0000000 --- a/board/Marvell/mvebu_db-88f3720/Makefile +++ /dev/null @@ -1,7 +0,0 @@ -# -# Copyright (C) 2016 Stefan Roese -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := board.o diff --git a/board/Marvell/mvebu_db-88f3720/board.c b/board/Marvell/mvebu_db-88f3720/board.c deleted file mode 100644 index edf88c7..0000000 --- a/board/Marvell/mvebu_db-88f3720/board.c +++ /dev/null @@ -1,134 +0,0 @@ -/* - * Copyright (C) 2016 Stefan Roese - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -/* IO expander I2C device */ -#define I2C_IO_EXP_ADDR 0x22 -#define I2C_IO_CFG_REG_0 0x6 -#define I2C_IO_DATA_OUT_REG_0 0x2 -#define I2C_IO_REG_0_SATA_OFF 2 -#define I2C_IO_REG_0_USB_H_OFF 1 - -int board_early_init_f(void) -{ - /* Nothing to do (yet), perhaps later some pin-muxing etc */ - - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; - - return 0; -} - -/* Board specific AHCI / SATA enable code */ -int board_ahci_enable(void) -{ - struct udevice *dev; - int ret; - u8 buf[8]; - - /* Configure IO exander PCA9555: 7bit address 0x22 */ - ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev); - if (ret) { - printf("Cannot find PCA9555: %d\n", ret); - return 0; - } - - ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1); - if (ret) { - printf("Failed to read IO expander value via I2C\n"); - return -EIO; - } - - /* - * Enable SATA power via IO expander connected via I2C by setting - * the corresponding bit to output mode to enable power for SATA - */ - buf[0] &= ~(1 << I2C_IO_REG_0_SATA_OFF); - ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1); - if (ret) { - printf("Failed to set IO expander via I2C\n"); - return -EIO; - } - - return 0; -} - -/* Board specific xHCI enable code */ -int board_xhci_enable(void) -{ - struct udevice *dev; - int ret; - u8 buf[8]; - - /* Configure IO exander PCA9555: 7bit address 0x22 */ - ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev); - if (ret) { - printf("Cannot find PCA9555: %d\n", ret); - return 0; - } - - printf("Enable USB VBUS\n"); - - /* - * Read configuration (direction) and set VBUS pin as output - * (reset pin = output) - */ - ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1); - if (ret) { - printf("Failed to read IO expander value via I2C\n"); - return -EIO; - } - buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF); - ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1); - if (ret) { - printf("Failed to set IO expander via I2C\n"); - return -EIO; - } - - /* Read VBUS output value and disable it */ - ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); - if (ret) { - printf("Failed to read IO expander value via I2C\n"); - return -EIO; - } - buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF); - ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); - if (ret) { - printf("Failed to set IO expander via I2C\n"); - return -EIO; - } - - /* - * Required delay for configuration to settle - must wait for - * power on port is disabled in case VBUS signal was high, - * required 3 seconds delay to let VBUS signal fully settle down - */ - mdelay(3000); - - /* Enable VBUS power: Set output value of VBUS pin as enabled */ - buf[0] |= (1 << I2C_IO_REG_0_USB_H_OFF); - ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); - if (ret) { - printf("Failed to set IO expander via I2C\n"); - return -EIO; - } - - mdelay(500); /* required delay to let output value settle */ - - return 0; -} diff --git a/configs/mvebu_db-88f3720_defconfig b/configs/mvebu_db-88f3720_defconfig index 80f2599..4286695 100644 --- a/configs/mvebu_db-88f3720_defconfig +++ b/configs/mvebu_db-88f3720_defconfig @@ -1,7 +1,7 @@ CONFIG_ARM=y CONFIG_ARCH_MVEBU=y CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_TARGET_MVEBU_DB_88F3720=y +CONFIG_TARGET_MVEBU_ARMADA_37XX=y CONFIG_DEFAULT_DEVICE_TREE="armada-3720-db" CONFIG_AHCI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set diff --git a/include/configs/mvebu_armada-37xx.h b/include/configs/mvebu_armada-37xx.h new file mode 100644 index 0000000..7eefdb2 --- /dev/null +++ b/include/configs/mvebu_armada-37xx.h @@ -0,0 +1,129 @@ +/* + * Copyright (C) 2016 Stefan Roese + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_MVEBU_ARMADA_37XX_H +#define _CONFIG_MVEBU_ARMADA_37XX_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_DISPLAY_BOARDINFO_LATE + +#define CONFIG_SYS_TEXT_BASE 0x00000000 + +/* additions for new ARM relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 + +#define CONFIG_NR_DRAM_BANKS 1 + +/* auto boot */ +#define CONFIG_PREBOOT + +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ + 115200, 230400, 460800, 921600 } + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG /* enable INITRD tag */ +#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */ + +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* 4MiB for malloc() */ + +/* + * Other required minimal configurations + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ +#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ +#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */ +#define CONFIG_SYS_MEMTEST_END 0x00ffffff /*(_16M -1) */ +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ +#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ + +#define CONFIG_SYS_ALT_MEMTEST + +/* End of 16M scrubbed by training in bootrom */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + 0xFF0000) + +/* + * I2C + */ +#define CONFIG_I2C_MV +#define CONFIG_SYS_I2C_SLAVE 0x0 + +/* + * SPI Flash configuration + */ +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 1000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE + +/* Environment in SPI NOR flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x180000 /* as Marvell U-Boot version */ +#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ +#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ + +/* + * Ethernet Driver configuration + */ +#define CONFIG_MVNETA /* Enable Marvell Gbe Controller Driver */ +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#define CONFIG_PHY_GIGE /* GbE speed/duplex detect */ +#define CONFIG_ARP_TIMEOUT 200 +#define CONFIG_NET_RETRY_COUNT 50 + +/* USB 2.0 */ +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 + +/* USB 3.0 */ +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 3 + +#define CONFIG_USB_MAX_CONTROLLER_COUNT (CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS + \ + CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS) + +/* USB ethernet */ +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_ETHER_MCS7830 +#define CONFIG_USB_ETHER_RTL8152 +#define CONFIG_USB_ETHER_SMSC95XX + +/* + * SATA/SCSI/AHCI configuration + */ +#define CONFIG_SCSI +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_LIBATA +#define CONFIG_LBA48 +#define CONFIG_SYS_64BIT_LBA + +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + +#define CONFIG_SUPPORT_VFAT + +#endif /* _CONFIG_MVEBU_ARMADA_37XX_H */ diff --git a/include/configs/mvebu_db-88f3720.h b/include/configs/mvebu_db-88f3720.h deleted file mode 100644 index 6bb78e0..0000000 --- a/include/configs/mvebu_db-88f3720.h +++ /dev/null @@ -1,129 +0,0 @@ -/* - * Copyright (C) 2016 Stefan Roese - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _CONFIG_MVEBU_DB_88F3720_H -#define _CONFIG_MVEBU_DB_88F3720_H - -/* - * High Level Configuration Options (easy to change) - */ -#define CONFIG_DISPLAY_BOARDINFO_LATE - -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -/* additions for new ARM relocation support */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_NR_DRAM_BANKS 1 - -/* auto boot */ -#define CONFIG_PREBOOT - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400, 460800, 921600 } - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */ - -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* 4MiB for malloc() */ - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_AUTO_COMPLETE -#define CONFIG_CMDLINE_EDITING -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */ -#define CONFIG_SYS_MEMTEST_END 0x00ffffff /*(_16M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ - -#define CONFIG_SYS_ALT_MEMTEST - -/* End of 16M scrubbed by training in bootrom */ -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + 0xFF0000) - -/* - * I2C - */ -#define CONFIG_I2C_MV -#define CONFIG_SYS_I2C_SLAVE 0x0 - -/* - * SPI Flash configuration - */ -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 - -/* SPI NOR flash default params, used by sf commands */ -#define CONFIG_SF_DEFAULT_SPEED 1000000 -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 -#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE - -/* Environment in SPI NOR flash */ -#define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_OFFSET 0x180000 /* as Marvell U-Boot version */ -#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ -#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ - -/* - * Ethernet Driver configuration - */ -#define CONFIG_MVNETA /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_PHY_GIGE /* GbE speed/duplex detect */ -#define CONFIG_ARP_TIMEOUT 200 -#define CONFIG_NET_RETRY_COUNT 50 - -/* USB 2.0 */ -#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 - -/* USB 3.0 */ -#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 3 - -#define CONFIG_USB_MAX_CONTROLLER_COUNT (CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS + \ - CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS) - -/* USB ethernet */ -#define CONFIG_USB_HOST_ETHER -#define CONFIG_USB_ETHER_ASIX -#define CONFIG_USB_ETHER_MCS7830 -#define CONFIG_USB_ETHER_RTL8152 -#define CONFIG_USB_ETHER_SMSC95XX - -/* - * SATA/SCSI/AHCI configuration - */ -#define CONFIG_SCSI -#define CONFIG_SCSI_AHCI -#define CONFIG_SCSI_AHCI_PLAT -#define CONFIG_LIBATA -#define CONFIG_LBA48 -#define CONFIG_SYS_64BIT_LBA - -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 -#define CONFIG_SYS_SCSI_MAX_LUN 1 -#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ - CONFIG_SYS_SCSI_MAX_LUN) - -#define CONFIG_SUPPORT_VFAT - -#endif /* _CONFIG_MVEBU_DB_88F3720_H */ -- cgit v0.10.2