From 972f5320dae1d69b38cd06c6c2a23da8ae5a654a Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Wed, 2 Sep 2015 10:40:29 +0900 Subject: powerpc: mpc5xx: remove cmi_mpc5xx support This has not been converted to Generic Board, so should be removed. (See doc/README.generic-board for details.) Signed-off-by: Masahiro Yamada diff --git a/arch/powerpc/cpu/mpc5xx/Kconfig b/arch/powerpc/cpu/mpc5xx/Kconfig index 5275447..d81bfd2 100644 --- a/arch/powerpc/cpu/mpc5xx/Kconfig +++ b/arch/powerpc/cpu/mpc5xx/Kconfig @@ -8,15 +8,11 @@ choice prompt "Target select" optional -config TARGET_CMI_MPC5XX - bool "Support cmi_mpc5xx" - config TARGET_PATI bool "Support PATI" endchoice -source "board/cmi/Kconfig" source "board/mpl/pati/Kconfig" endmenu diff --git a/board/cmi/Kconfig b/board/cmi/Kconfig deleted file mode 100644 index 6efe6b1..0000000 --- a/board/cmi/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_CMI_MPC5XX - -config SYS_BOARD - default "cmi" - -config SYS_CONFIG_NAME - default "cmi_mpc5xx" - -endif diff --git a/board/cmi/MAINTAINERS b/board/cmi/MAINTAINERS deleted file mode 100644 index 60701bf..0000000 --- a/board/cmi/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -CMI BOARD -#M: - -S: Maintained -F: board/cmi/ -F: include/configs/cmi_mpc5xx.h -F: configs/cmi_mpc5xx_defconfig diff --git a/board/cmi/Makefile b/board/cmi/Makefile deleted file mode 100644 index cd3bb0d..0000000 --- a/board/cmi/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := flash.o cmi.o diff --git a/board/cmi/README b/board/cmi/README deleted file mode 100644 index 0edd50a..0000000 --- a/board/cmi/README +++ /dev/null @@ -1,84 +0,0 @@ - -Summary: -======== - -This file contains information about the cmi board configuration. -Please see cmi_mpc5xx_config for further details. The cmi board is -a customer specific board but should work with small modifications -on every board which has a MPC5xx and either a 28F128J3A, -28F320J3A or 28F640J3A Intel flash mounted. - -Board Discription: -================== - -* Motorola MPC555 -* RS232 connection -* Intel flash 28F640J3A -* Micron SRAM 1M -* Altera PLD - -Bootstrap: -========== - -In contrast to the usual boot sequence used in U-Boot, on the -cmi board we don't boot from the external flash directly. -Because of we use a 16-bit flash and don't sample a RCW -from the data bus to set the startup buswidth to 16-bit. -Unfortunatly the default width, sampled from the default RCW -is 32-bit. For this reason we burn the proper RCW into the -internal flash shadow location and boot after power-on or -reset from the internal flash and then branch to 0x02000100 -where the U-Boot reset vector handler is located. - -Memory Map: -=========== - -Memory Map after relocation: - - 0x0000 0000 CONFIG_SYS_SDRAM_BASE - : - 0x000F 9FFF - : - : - 0x0100 0000 CONFIG_SYS_IMMR (Internal memory map base adress) - : - 0x0130 7FFF - : - : - 0x0200 0000 CONFIG_SYS_FLASH_BASE - : - 0x027C FFFF - : - : - 0x0300 0000 PLD_BASE - -Flash Partition: - - 0x0200 0000 Block 0 and 1 contain U-Boot except - : environment - : - 0x0201 FFFF - 0x0202 0000 Block 2 contains environment (.ppcenv) - : - 0x0202 FFFF - -See README file for futher information about U-Boot relocation -and partitioning. - -Tested Features: -================ - -* U-Boot commands: go, loads, loadb, all memory features, printenv, - setenv, saveenv, protect, erase, fli, bdi, mtest, reset, version, - coninfo, help (see configuration file for available commands) - -* Blinking led to indicate boot process - -Added or Changed Files: -======================= - -u-boot-0.2.0/board/cmi/* -u-boot-0.2.0/include/configs/cmi_mpc5xx.h - -Regards, -Martin diff --git a/board/cmi/cmi.c b/board/cmi/cmi.c deleted file mode 100644 index 37028c3..0000000 --- a/board/cmi/cmi.c +++ /dev/null @@ -1,57 +0,0 @@ -/* - * (C) Copyright 2003 - * Martin Winistoerfer, martinwinistoerfer@gmx.ch. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * File: cmi.c - * - * Discription: For generic board specific functions - * - */ - - -#include -#include - -#define SRAM_SIZE 1024000L /* 1M RAM available*/ - -#if defined(__APPLE__) -/* Leading underscore on symbols */ -# define SYM_CHAR "_" -#else /* No leading character on symbols */ -# define SYM_CHAR -#endif - -/* - * Macros to generate global absolutes. - */ -#define GEN_SYMNAME(str) SYM_CHAR #str -#define GEN_VALUE(str) #str -#define GEN_ABS(name, value) \ - asm (".globl " GEN_SYMNAME(name)); \ - asm (GEN_SYMNAME(name) " = " GEN_VALUE(value)) - -/* - * Check the board - */ -int checkboard(void) -{ - puts ("Board: ### No HW ID - assuming CMI board\n"); - return (0); -} - -/* - * Get RAM size. - */ -phys_size_t initdram(int board_type) -{ - return (SRAM_SIZE); /* We currently have a static size adapted for cmi board. */ -} - -/* - * Absolute environment address for linker file. - */ -GEN_ABS(env_start, CONFIG_ENV_OFFSET + CONFIG_SYS_FLASH_BASE); diff --git a/board/cmi/flash.c b/board/cmi/flash.c deleted file mode 100644 index d9986f9..0000000 --- a/board/cmi/flash.c +++ /dev/null @@ -1,501 +0,0 @@ -/* - * (C) Copyright 2003 - * Martin Winistoerfer, martinwinistoerfer@gmx.ch. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * File: flash.c - * - * Discription: This Driver is for 28F320J3A, 28F640J3A and - * 28F128J3A Intel flashs working in 16 Bit mode. - * They are single bank flashs. - * - * Most of this code is taken from existing u-boot - * source code. - */ - - -#include -#include - -#if defined(CONFIG_ENV_IS_IN_FLASH) -# ifndef CONFIG_ENV_ADDR -# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) -# endif -# ifndef CONFIG_ENV_SIZE -# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -# endif -# ifndef CONFIG_ENV_SECT_SIZE -# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE -# endif -#endif - -#define FLASH_ID_MASK 0xFFFF -#define FLASH_BLOCK_SIZE 0x00010000 -#define FLASH_CMD_READ_ID 0x0090 -#define FLASH_CMD_RESET 0x00ff -#define FLASH_CMD_BLOCK_ERASE 0x0020 -#define FLASH_CMD_ERASE_CONFIRM 0x00D0 -#define FLASH_CMD_CLEAR_STATUS 0x0050 -#define FLASH_CMD_SUSPEND_ERASE 0x00B0 -#define FLASH_CMD_WRITE 0x0040 -#define FLASH_CMD_PROTECT 0x0060 -#define FLASH_CMD_PROTECT_SET 0x0001 -#define FLASH_CMD_PROTECT_CLEAR 0x00D0 -#define FLASH_STATUS_DONE 0x0080 - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - -/* - * Local function prototypes - */ -static ulong flash_get_size (vu_short *addr, flash_info_t *info); -static int write_short (flash_info_t *info, ulong dest, ushort data); -static void flash_get_offsets (ulong base, flash_info_t *info); - -/* - * Initialize flash - */ - -unsigned long flash_init (void) -{ - unsigned long size_b0; - int i; - - /* Init: no FLASHes known */ - for (i=0; i= CONFIG_SYS_FLASH_BASE - /* monitor protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1, - &flash_info[0]); -#endif - -#ifdef CONFIG_ENV_IS_IN_FLASH - /* ENV protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE-1, - &flash_info[0]); -#endif - - return size_b0; -} - -/* - * Compute start adress of each sector (block) - */ - -static void flash_get_offsets (ulong base, flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_INTEL: - for (i = 0; i < info->sector_count; i++) { - info->start[i] = base + i * FLASH_BLOCK_SIZE; - } - return; - - default: - printf ("Don't know sector offsets for flash type 0x%lx\n", - info->flash_id); - return; - } -} - -/* - * Print flash information - */ -void flash_print_info (flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_AMD: printf ("AMD "); break; - case FLASH_MAN_FUJ: printf ("Fujitsu "); break; - case FLASH_MAN_SST: printf ("SST "); break; - case FLASH_MAN_STM: printf ("STM "); break; - case FLASH_MAN_INTEL: printf ("Intel "); break; - case FLASH_MAN_MT: printf ("MT "); break; - default: printf ("Unknown Vendor "); break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_28F320J3A: printf ("28F320J3A (32Mbit) 16-Bit\n"); - break; - case FLASH_28F640J3A: printf ("28F640J3A (64Mbit) 16-Bit\n"); - break; - case FLASH_28F128J3A: printf ("28F128J3A (128Mbit) 16-Bit\n"); - break; - default: printf ("Unknown Chip Type\n"); - break; - } - - if (info->size >= (1 << 20)) { - i = 20; - } else { - i = 10; - } - printf (" Size: %ld %cB in %d Sectors\n", - info->size >> i, - (i == 20) ? 'M' : 'k', - info->sector_count); - - printf (" Sector Start Addresses:"); - for (i=0; isector_count; ++i) { - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s", - info->start[i], - info->protect[i] ? " (RO)" : " " - ); - } - printf ("\n"); - return; -} - -/* - * Get size of flash in bytes. - * The following code cannot be run from FLASH! - */ - -static ulong flash_get_size (vu_short *addr, flash_info_t *info) -{ - vu_short value; - - /* Read Manufacturer ID */ - addr[0] = FLASH_CMD_READ_ID; - value = addr[0]; - - switch (value) { - case (AMD_MANUFACT & FLASH_ID_MASK): - info->flash_id = FLASH_MAN_AMD; - break; - case (FUJ_MANUFACT & FLASH_ID_MASK): - info->flash_id = FLASH_MAN_FUJ; - break; - case (SST_MANUFACT & FLASH_ID_MASK): - info->flash_id = FLASH_MAN_SST; - break; - case (STM_MANUFACT & FLASH_ID_MASK): - info->flash_id = FLASH_MAN_STM; - break; - case (INTEL_MANUFACT & FLASH_ID_MASK): - info->flash_id = FLASH_MAN_INTEL; - break; - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - addr[0] = FLASH_CMD_RESET; /* restore read mode */ - return (0); /* no or unknown flash */ - } - - value = addr[1]; /* device ID */ - - switch (value) { - case (INTEL_ID_28F320J3A & FLASH_ID_MASK): - info->flash_id += FLASH_28F320J3A; - info->sector_count = 32; - info->size = 0x00400000; - break; /* => 32 MBit */ - - case (INTEL_ID_28F640J3A & FLASH_ID_MASK): - info->flash_id += FLASH_28F640J3A; - info->sector_count = 64; - info->size = 0x00800000; - break; /* => 64 MBit */ - - case (INTEL_ID_28F128J3A & FLASH_ID_MASK): - info->flash_id += FLASH_28F128J3A; - info->sector_count = 128; - info->size = 0x01000000; - break; /* => 128 MBit */ - - default: - info->flash_id = FLASH_UNKNOWN; - addr[0] = FLASH_CMD_RESET; /* restore read mode */ - return (0); /* => no or unknown flash */ - - } - - if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) { - printf ("** ERROR: sector count %d > max (%d) **\n", - info->sector_count, CONFIG_SYS_MAX_FLASH_SECT); - info->sector_count = CONFIG_SYS_MAX_FLASH_SECT; - } - - addr[0] = FLASH_CMD_RESET; /* restore read mode */ - - return (info->size); -} - - -/* - * Erase unprotected sectors - */ - -int flash_erase (flash_info_t *info, int s_first, int s_last) -{ - int flag, prot, sect; - ulong start, now, last; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - if ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL) { - printf ("Can erase only Intel flash types - aborted\n"); - return 1; - } - - prot = 0; - for (sect=s_first; sect<=s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - start = get_timer (0); - last = start; - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - vu_short *addr = (vu_short *)(info->start[sect]); - unsigned long status; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - -#ifdef DEBUG - printf("Erase sector %d at start addr 0x%08X", sect, (unsigned int)info->start[sect]); -#endif - - *addr = FLASH_CMD_CLEAR_STATUS; - *addr = FLASH_CMD_BLOCK_ERASE; - *addr = FLASH_CMD_ERASE_CONFIRM; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* wait at least 80us - let's wait 1 ms */ - udelay (1000); - - while (((status = *addr) & FLASH_STATUS_DONE) != FLASH_STATUS_DONE) { - if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf("Flash erase timeout at address %lx\n", info->start[sect]); - *addr = FLASH_CMD_SUSPEND_ERASE; - *addr = FLASH_CMD_RESET; - return 1; - } - - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - putc ('.'); - last = now; - } - } - *addr = FLASH_CMD_RESET; - } - } - printf (" done\n"); - return 0; -} - -/* - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - * 4 - Flash not identified - */ - -int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) -{ - ulong cp, wp; - ushort data; - int i, rc; - - if (info->flash_id == FLASH_UNKNOWN) { - return 4; - } - - wp = (addr & ~1); /* get lower word aligned address */ - - /* - * handle unaligned start byte - */ - - if (addr - wp) { - data = 0; - data = (data << 8) | *src++; - --cnt; - if ((rc = write_short(info, wp, data)) != 0) { - return (rc); - } - wp += 2; - } - - /* - * handle word aligned part - */ - - while (cnt >= 2) { - data = 0; - for (i=0; i<2; ++i) { - data = (data << 8) | *src++; - } - - if ((rc = write_short(info, wp, data)) != 0) { - return (rc); - } - wp += 2; - cnt -= 2; - } - - if (cnt == 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - - data = 0; - for (i=0, cp=wp; i<2 && cnt>0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i<2; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - - return (write_short(info, wp, data)); - -} - -/* - * Write 16 bit (short) to flash - */ - -static int write_short (flash_info_t *info, ulong dest, ushort data) -{ - vu_short *addr = (vu_short*)(info->start[0]); - ulong start; - int flag; - - /* Check if Flash is (sufficiently) erased */ - if ((*((vu_short *)dest) & data) != data) { - return (2); - } - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - if (!(info->flash_id & FLASH_VENDMASK)) { - return 4; - } - *addr = FLASH_CMD_ERASE_CONFIRM; - *addr = FLASH_CMD_WRITE; - - *((vu_short *)dest) = data; - - /* re-enable interrupts if necessary */ - if (flag) { - enable_interrupts(); - } - - /* data polling for D7 */ - start = get_timer (0); - - /* wait for error or finish */ - while(!(addr[0] & FLASH_STATUS_DONE)){ - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) { - addr[0] = FLASH_CMD_RESET; - return (1); - } - } - - *addr = FLASH_CMD_RESET; - return (0); -} - -/* - * Protects a flash sector - */ - -int flash_real_protect(flash_info_t *info, long sector, int prot) -{ - vu_short *addr = (vu_short*)(info->start[sector]); - ulong start; - - *addr = FLASH_CMD_CLEAR_STATUS; - *addr = FLASH_CMD_PROTECT; - - if(prot) { - *addr = FLASH_CMD_PROTECT_SET; - } else { - *addr = FLASH_CMD_PROTECT_CLEAR; - } - - /* wait for error or finish */ - start = get_timer (0); - while(!(addr[0] & FLASH_STATUS_DONE)){ - if (get_timer(start) > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf("Flash protect timeout at address %lx\n", info->start[sector]); - addr[0] = FLASH_CMD_RESET; - return (1); - } - } - /* Set software protect flag */ - info->protect[sector] = prot; - *addr = FLASH_CMD_RESET; - return (0); -} diff --git a/configs/cmi_mpc5xx_defconfig b/configs/cmi_mpc5xx_defconfig deleted file mode 100644 index abebfab..0000000 --- a/configs/cmi_mpc5xx_defconfig +++ /dev/null @@ -1,6 +0,0 @@ -CONFIG_PPC=y -CONFIG_5xx=y -CONFIG_TARGET_CMI_MPC5XX=y -# CONFIG_CMD_SETEXPR is not set -# CONFIG_CMD_NET is not set -# CONFIG_CMD_NFS is not set diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 438ac8c..d97e82f 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +cmi_mpc5xx powerpc mpc5xx - - zeus powerpc ppc4xx - - Stefan Roese sbc405 powerpc ppc4xx - - pcs440ep powerpc ppc4xx - - Stefan Roese diff --git a/include/configs/cmi_mpc5xx.h b/include/configs/cmi_mpc5xx.h deleted file mode 100644 index d081865..0000000 --- a/include/configs/cmi_mpc5xx.h +++ /dev/null @@ -1,240 +0,0 @@ -/* - * (C) Copyright 2003 - * Martin Winistoerfer, martinwinistoerfer@gmx.ch. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * File: cmi_mpc5xx.h - * - * Discription: Config header file for cmi - * board using an MPC5xx CPU - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ - -#define CONFIG_MPC555 1 /* This is an MPC555 CPU */ -#define CONFIG_CMI 1 /* Using the customized cmi board */ - -#define CONFIG_SYS_TEXT_BASE 0x02000000 /* Boot from flash at location 0x00000000 */ - -/* Serial Console Configuration */ -#define CONFIG_5xx_CONS_SCI1 -#undef CONFIG_5xx_CONS_SCI2 - -#define CONFIG_BAUDRATE 57600 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_ASKENV - - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif -#define CONFIG_BOOTCOMMAND "go 02034004" /* autoboot command */ - -#define CONFIG_BOOTARGS "" /* Assuming OS Image in 4 flash sector at offset 4004 */ - -#define CONFIG_WATCHDOG /* turn on platform specific watchdog */ - -#define CONFIG_STATUS_LED 1 /* Enable status led */ - -#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */ - -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x000fa000 /* 1 MB in SRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 } - - -/* - * Low Level Configuration Settings - */ - -/* - * Internal Memory Mapped (This is not the IMMR content) - */ -#define CONFIG_SYS_IMMR 0x01000000 /* Physical start adress of internal memory map */ - -/* - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */ -#define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */ -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */ -#define CONFIG_SYS_INIT_SP_ADDR 0x013fa000 /* Physical start adress of inital stack */ - -/* - * Start addresses for the final memory configuration - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */ -#define CONFIG_SYS_FLASH_BASE 0x02000000 /* External flash */ -#define PLD_BASE 0x03000000 /* PLD */ -#define ANYBUS_BASE 0x03010000 /* Anybus Module */ - -#define CONFIG_SYS_RESET_ADRESS 0x01000000 /* Adress which causes reset */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */ - /* This adress is given to the linker with -Ttext to */ - /* locate the text section at this adress. */ -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (64 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - - -/*----------------------------------------------------------------------- - * FLASH organization - *----------------------------------------------------------------------- - * - */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Physically section protection on */ - -#define CONFIG_ENV_IS_IN_FLASH 1 - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_OFFSET 0x00020000 /* Environment starts at this adress */ -#define CONFIG_ENV_SIZE 0x00010000 /* Set whole sector as env */ -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWP) -#endif /* CONFIG_WATCHDOG */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PITF) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF00 -#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \ - SCCR_COM00 | SCCR_DFNL000 | SCCR_DFNH000) - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration - *----------------------------------------------------------------------- - * Data show cycle - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00) /* Disable data show cycle */ - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register - *----------------------------------------------------------------------- - * Set all bits to 40 Mhz - * - */ -#define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */ -#define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0) - - -/*----------------------------------------------------------------------- - * UMCR - UIMB Module Configuration Register - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */ - -/*----------------------------------------------------------------------- - * ICTRL - I-Bus Support Control Register - */ -#define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */ - -/*----------------------------------------------------------------------- - * USIU - Memory Controller Register - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16) -#define CONFIG_SYS_OR0_PRELIM (OR_ADDR_MK_FF | OR_SCY_3) -#define CONFIG_SYS_BR1_PRELIM (ANYBUS_BASE) -#define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FFFF | OR_SCY_1 | OR_ETHR) -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_PS_32) -#define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF) -#define CONFIG_SYS_BR3_PRELIM (PLD_BASE | BR_V | BR_BI | BR_LBDIR | BR_PS_8) -#define CONFIG_SYS_OR3_PRELIM (OR_ADDR_MK_FF | OR_TRLX | OR_BSCY | OR_SCY_8 | \ - OR_ACS_10 | OR_ETHR | OR_CSNT) - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */ - -/*----------------------------------------------------------------------- - * DER - Timer Decrementer - *----------------------------------------------------------------------- - * Initialise to zero - */ -#define CONFIG_SYS_DER 0x00000000 - -#endif /* __CONFIG_H */ diff --git a/include/status_led.h b/include/status_led.h index a5e35df..f6be181 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -64,19 +64,6 @@ void status_led_set (int led, int state); * filling this file up with lots of custom board stuff. */ -/***** CMI ********************************************************/ -#elif defined(CONFIG_CMI) -# define STATUS_LED_DIR im_mios.mios_mpiosm32ddr -# define STATUS_LED_DAT im_mios.mios_mpiosm32dr - -# define STATUS_LED_BIT 0x2000 /* Select one of the 16 possible*/ - /* MIOS outputs */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* Blinking periode is 500 ms */ -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 0 */ -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - #elif defined(CONFIG_V38B) # define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */ -- cgit v0.10.2