From 8bd522ce4afda3d4868ee8c913f5394094326be1 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Fri, 11 Jan 2008 18:48:24 +0800 Subject: mpc83xx: Add the support for MPC8315ERDB board The features list: - Boot from NOR Flash - DDR2 266MHz hardcoded configuration - Local bus NOR Flash R/W operation - I2C, UART, MII and RTC - eTSEC0/1 support - PCI host Signed-off-by: Dave Liu Signed-off-by: Kim Phillips diff --git a/CREDITS b/CREDITS index 1130c9e..edf825c 100644 --- a/CREDITS +++ b/CREDITS @@ -305,7 +305,7 @@ W: http://www.li-pro.net N: Dave Liu E: daveliu@freescale.com -D: Support for MPC832x, MPC8360, MPC837x +D: Support for MPC8315, MPC832x, MPC8360, MPC837x W: www.freescale.com N: Raymond Lo diff --git a/MAINTAINERS b/MAINTAINERS index 40b2b51..528a536 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -232,6 +232,7 @@ The LEOX team Dave Liu + MPC8315ERDB MPC8315 MPC832XEMDS MPC832x MPC8360EMDS MPC8360 MPC837XEMDS MPC837x diff --git a/MAKEALL b/MAKEALL index bec3541..efd4444 100755 --- a/MAKEALL +++ b/MAKEALL @@ -309,6 +309,7 @@ LIST_8260=" \ LIST_83xx=" \ MPC8313ERDB_33 \ MPC8313ERDB_66 \ + MPC8315ERDB \ MPC8323ERDB \ MPC832XEMDS \ MPC832XEMDS_ATM \ diff --git a/Makefile b/Makefile index 8a888b9..8be0dfa 100644 --- a/Makefile +++ b/Makefile @@ -1861,6 +1861,9 @@ MPC8313ERDB_66_config: unconfig fi ; @$(MKCONFIG) -a MPC8313ERDB ppc mpc83xx mpc8313erdb freescale +MPC8315ERDB_config: unconfig + @$(MKCONFIG) -a MPC8315ERDB ppc mpc83xx mpc8315erdb freescale + MPC8323ERDB_config: unconfig @$(MKCONFIG) -a MPC8323ERDB ppc mpc83xx mpc8323erdb freescale diff --git a/board/freescale/mpc8315erdb/Makefile b/board/freescale/mpc8315erdb/Makefile new file mode 100644 index 0000000..a987e510 --- /dev/null +++ b/board/freescale/mpc8315erdb/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o sdram.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) crv $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mpc8315erdb/config.mk b/board/freescale/mpc8315erdb/config.mk new file mode 100644 index 0000000..f768264 --- /dev/null +++ b/board/freescale/mpc8315erdb/config.mk @@ -0,0 +1 @@ +TEXT_BASE = 0xFE000000 diff --git a/board/freescale/mpc8315erdb/mpc8315erdb.c b/board/freescale/mpc8315erdb/mpc8315erdb.c new file mode 100644 index 0000000..7af36dd --- /dev/null +++ b/board/freescale/mpc8315erdb/mpc8315erdb.c @@ -0,0 +1,132 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * + * Author: Scott Wood + * Dave Liu + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#if defined(CONFIG_OF_LIBFDT) +#include +#endif +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + volatile immap_t *im = (immap_t *)CFG_IMMR; + + if (im->pmc.pmccr1 & PMCCR1_POWER_OFF) + gd->flags |= GD_FLG_SILENT; + + return 0; +} + +static u8 read_board_info(void) +{ + u8 val8; + i2c_set_bus_num(0); + + if (i2c_read(CFG_I2C_PCF8574A_ADDR, 0, 0, &val8, 1) == 0) + return val8; + else + return 0; +} + +int checkboard(void) +{ + static const char * const rev_str[] = { + "0.0", + "0.1", + "1.0", + "1.1", + "", + }; + u8 info; + int i; + + info = read_board_info(); + i = (!info) ? 4: info & 0x03; + + printf("Board: Freescale MPC8315ERDB Rev %s\n", rev_str[i]); + + return 0; +} + +static struct pci_region pci_regions[] = { + { + bus_start: CFG_PCI_MEM_BASE, + phys_start: CFG_PCI_MEM_PHYS, + size: CFG_PCI_MEM_SIZE, + flags: PCI_REGION_MEM | PCI_REGION_PREFETCH + }, + { + bus_start: CFG_PCI_MMIO_BASE, + phys_start: CFG_PCI_MMIO_PHYS, + size: CFG_PCI_MMIO_SIZE, + flags: PCI_REGION_MEM + }, + { + bus_start: CFG_PCI_IO_BASE, + phys_start: CFG_PCI_IO_PHYS, + size: CFG_PCI_IO_SIZE, + flags: PCI_REGION_IO + } +}; + +void pci_init_board(void) +{ + volatile immap_t *immr = (volatile immap_t *)CFG_IMMR; + volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk; + volatile law83xx_t *pci_law = immr->sysconf.pcilaw; + struct pci_region *reg[] = { pci_regions }; + int warmboot; + + /* Enable all 3 PCI_CLK_OUTPUTs. */ + clk->occr |= 0xe0000000; + + /* + * Configure PCI Local Access Windows + */ + pci_law[0].bar = CFG_PCI_MEM_PHYS & LAWBAR_BAR; + pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB; + + pci_law[1].bar = CFG_PCI_IO_PHYS & LAWBAR_BAR; + pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB; + + warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM; + warmboot |= immr->pmc.pmccr1 & PMCCR1_POWER_OFF; + + mpc83xx_pci_init(1, reg, warmboot); +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); +#endif +} +#endif diff --git a/board/freescale/mpc8315erdb/sdram.c b/board/freescale/mpc8315erdb/sdram.c new file mode 100644 index 0000000..f97e3c7 --- /dev/null +++ b/board/freescale/mpc8315erdb/sdram.c @@ -0,0 +1,120 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * + * Authors: Nick.Spence@freescale.com + * Wilson.Lo@freescale.com + * scottwood@freescale.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +#include +#include + +#include + +DECLARE_GLOBAL_DATA_PTR; + +static void resume_from_sleep(void) +{ + u32 magic = *(u32 *)0; + + typedef void (*func_t)(void); + func_t resume = *(func_t *)4; + + if (magic == 0xf5153ae5) + resume(); + + gd->flags &= ~GD_FLG_SILENT; + puts("\nResume from sleep failed: bad magic word\n"); +} + +/* Fixed sdram init -- doesn't use serial presence detect. + * + * This is useful for faster booting in configs where the RAM is unlikely + * to be changed, or for things like NAND booting where space is tight. + */ +static long fixed_sdram(void) +{ + volatile immap_t *im = (volatile immap_t *)CFG_IMMR; + u32 msize = CFG_DDR_SIZE * 1024 * 1024; + u32 msize_log2 = __ilog2(msize); + + im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12; + im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1); + im->sysconf.ddrcdr = CFG_DDRCDR_VALUE; + + /* + * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg], + * or the DDR2 controller may fail to initialize correctly. + */ + udelay(50000); + + im->ddr.csbnds[0].csbnds = (msize - 1) >> 24; + im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG; + + /* Currently we use only one CS, so disable the other bank. */ + im->ddr.cs_config[1] = 0; + + im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL; + im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3; + im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2; + im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0; + + if (im->pmc.pmccr1 & PMCCR1_POWER_OFF) + im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG | SDRAM_CFG_BI; + else + im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG; + + im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2; + im->ddr.sdram_mode = CFG_DDR_MODE; + im->ddr.sdram_mode2 = CFG_DDR_MODE2; + + im->ddr.sdram_interval = CFG_DDR_INTERVAL; + sync(); + + /* enable DDR controller */ + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + sync(); + + return msize; +} + +long int initdram(int board_type) +{ + volatile immap_t *im = (volatile immap_t *)CFG_IMMR; + u32 msize; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im) + return -1; + + /* DDR SDRAM */ + msize = fixed_sdram(); + + if (im->pmc.pmccr1 & PMCCR1_POWER_OFF) + resume_from_sleep(); + + /* return total bus SDRAM size(bytes) -- DDR */ + return msize; +} diff --git a/doc/README.mpc8315erdb b/doc/README.mpc8315erdb new file mode 100644 index 0000000..c630cf8 --- /dev/null +++ b/doc/README.mpc8315erdb @@ -0,0 +1,80 @@ +Freescale MPC8315ERDB Board +----------------------------------------- + +1. Board Switches and Jumpers + + S3 is used to set CFG_RESET_SOURCE. + + To boot the image at 0xFE000000 in NOR flash, use these DIP + switche settings for S3 S4: + + +------+ +------+ + | | | **** | + | **** | | | + +------+ ON +------+ ON + 4321 4321 + (where the '*' indicates the position of the tab of the switch.) + +2. Memory Map + The memory map looks like this: + + 0x0000_0000 0x07ff_ffff DDR 128M + 0x8000_0000 0x8fff_ffff PCI MEM 256M + 0x9000_0000 0x9fff_ffff PCI_MMIO 256M + 0xe000_0000 0xe00f_ffff IMMR 1M + 0xe030_0000 0xe03f_ffff PCI IO 1M + 0xe060_0000 0xe060_7fff NAND FLASH (CS1) 32K + 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC8315ERDB.h + + CONFIG_MPC83xx MPC83xx family + CONFIG_MPC831x MPC831x specific + CONFIG_MPC8315 MPC8315 specific + CONFIG_MPC8315ERDB MPC8315ERDB board specific + +4. Compilation + + Assuming you're using BASH (or similar) as your shell: + + export CROSS_COMPILE=your-cross-compiler-prefix- + make distclean + make MPC8315ERDB_config + make all + +5. Downloading and Flashing Images + +5.1 Reflash U-boot Image using U-boot + + tftp 40000 u-boot.bin + protect off all + erase fe000000 fe1fffff + + cp.b 40000 fe000000 xxxx + protect on all + + You have to supply the correct byte count with 'xxxx' + from the TFTP result log. + +5.2 Downloading and Booting Linux Kernel + + Ensure that all networking-related environment variables are set + properly (including ipaddr, serverip, gatewayip (if needed), + netmask, ethaddr, eth1addr, rootpath (if using NFS root), + fdtfile, and bootfile). + + Then, do one of the following, depending on whether you + want an NFS root or a ramdisk root: + + =>run nfsboot + or + =>run ramboot + +6 Notes + + Booting from NAND flash is not yet supported. + The console baudrate for MPC8315ERDB is 115200bps. diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h new file mode 100644 index 0000000..ad2305c --- /dev/null +++ b/include/configs/MPC8315ERDB.h @@ -0,0 +1,547 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * + * Dave Liu + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83XX 1 /* MPC83xx family */ +#define CONFIG_MPC831X 1 /* MPC831x CPU family */ +#define CONFIG_MPC8315 1 /* MPC8315 CPU specific */ +#define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */ + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 66666667 /* in Hz */ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66.66MHz, then + * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz + */ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_2X1 |\ + HRCWL_CORE_TO_CSB_3X1) +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LALE_NORMAL) + +/* + * System IO Config + */ +#define CFG_SICRH 0x00000000 +#define CFG_SICRL 0x00000000 /* 3.3V, no delay */ + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ + +/* + * IMMR new address + */ +#define CFG_IMMR 0xE0000000 + +/* + * Arbiter Setup + */ +#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ +#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ +#define CFG_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CFG_DDRCDR_VALUE ( DDRCDR_EN \ + | DDRCDR_PZ_LOZ \ + | DDRCDR_NZ_LOZ \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN ) + /* 0x7b880001 */ +/* + * Manually set up DDR parameters + * consist of two chips HY5PS12621BFP-C4 from HYNIX + */ +#define CFG_DDR_SIZE 128 /* MB */ +#define CFG_DDR_CS0_BNDS 0x00000007 +#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \ + | 0x00010000 /* ODT_WR to CSn */ \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 ) + /* 0x80010102 */ +#define CFG_DDR_TIMING_3 0x00000000 +#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ + | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ + | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) + /* 0x00220802 */ +#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ + | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ + | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ + | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ + | ( 6 << TIMING_CFG1_REFREC_SHIFT ) \ + | ( 2 << TIMING_CFG1_WRREC_SHIFT ) \ + | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ + | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) + /* 0x39356222 */ +#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ + | ( 4 << TIMING_CFG2_CPO_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ + | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ + | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ + | ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) ) + /* 0x121048c7 */ +#define CFG_DDR_INTERVAL ( ( 0x0360 << SDRAM_INTERVAL_REFINT_SHIFT ) \ + | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) + /* 0x03600100 */ +#define CFG_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_32_BE ) + /* 0x43080000 */ +#define CFG_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ +#define CFG_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \ + | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) ) + /* ODT 150ohm CL=3, AL=1 on SDRAM */ +#define CFG_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00040000 /* memtest region */ +#define CFG_MEMTEST_END 0x00140000 + +/* + * The reserved memory + */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2) +#define CFG_LBC_LBCR 0x00040000 + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CFG_FLASH_SIZE 8 /* FLASH size is 8M */ + +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */ + +#define CFG_BR0_PRELIM ( CFG_FLASH_BASE /* Flash Base address */ \ + | (2 << BR_PS_SHIFT) /* 16 bit port size */ \ + | BR_V ) /* valid */ +#define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_0b11 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD ) + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 135 /* 127 64KB sectors and 8 8KB top sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * NAND Flash on the Local Bus + */ +#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE + +#define CFG_BR1_PRELIM ( CFG_NAND_BASE \ + | (2< " +#endif + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_FSL_I2C +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 + +/* + * Board info - revision and where boot from + */ +#define CFG_I2C_PCF8574A_ADDR 0x39 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI_MEM_BASE 0x80000000 +#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE +#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_MMIO_BASE 0x90000000 +#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE +#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_IO_BASE 0xE0300000 +#define CFG_PCI_IO_PHYS 0xE0300000 +#define CFG_PCI_IO_SIZE 0x100000 /* 1M */ + +#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE +#define CFG_PCI_SLV_MEM_BUS 0x00000000 +#define CFG_PCI_SLV_MEM_SIZE 0x80000000 + +#define CONFIG_PCI +#define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */ + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_EEPRO100 +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CFG_TSEC1_OFFSET 0x24000 +#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) +#define CFG_TSEC2_OFFSET 0x25000 +#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC1" +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC1" + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) + #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_DATE +#define CONFIG_CMD_PCI + +#if defined(CFG_RAMBOOT) + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS +#endif + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if defined(CONFIG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) +#define CFG_HID2 HID2_HBE + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U + +/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ +#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT1U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CFG_IBAT2L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT2U (CFG_FLASH_BASE | BATU_BL_8M | BATU_VS | BATU_VP) +#define CFG_DBAT2L (CFG_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT2U CFG_IBAT2U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CFG_IBAT3L (CFG_INIT_RAM_ADDR | BATL_PP_10) +#define CFG_IBAT3U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +/* PCI MEM space: cacheable */ +#define CFG_IBAT4L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT4U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT4L CFG_IBAT4L +#define CFG_DBAT4U CFG_IBAT4U + +/* PCI MMIO space: cache-inhibit and guarded */ +#define CFG_IBAT5L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT5U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U + +#define CFG_IBAT6L 0 +#define CFG_IBAT6U 0 +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U + +#define CFG_IBAT7L 0 +#define CFG_IBAT7U 0 +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_ETHADDR 04:00:00:00:00:0A +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 04:00:00:00:00:0B +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=ramfs.83xx\0" \ + "fdtaddr=400000\0" \ + "fdtfile=mpc8315erdb.dtb\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ -- cgit v0.10.2