/* * (C) Copyright 2001 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * Configuration settings for the sbc8240 board. */ /* ------------------------------------------------------------------------- */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC824X 1 #define CONFIG_MPC8240 1 #define CONFIG_WRSBC8240 1 #define CONFIG_SYS_TEXT_BASE 0xFFF00000 #define CONFIG_CONS_INDEX 1 #define CONFIG_BAUDRATE 9600 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } #define CONFIG_PREBOOT "echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type \"? or help\" to get on-line help;echo" #undef CONFIG_BOOTARGS #define CONFIG_BOOTCOMMAND "version;echo;tftpboot $loadaddr $loadfile;bootvx" /* autoboot command */ #define CONFIG_EXTRA_ENV_SETTINGS \ "bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st " \ "e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 " \ "tn=sbc8240 o=fei \0" \ "env_startaddr=FFF70000\0" \ "env_endaddr=FFF7FFFF\0" \ "loadfile=vxWorks.st\0" \ "loadaddr=0x01000000\0" \ "net_load=tftpboot $loadaddr $loadfile\0" \ "uboot_startaddr=FFF00000\0" \ "uboot_endaddr=FFF3FFFF\0" \ "update=tftp $loadaddr /u-boot.bin;" \ "protect off $uboot_startaddr $uboot_endaddr;" \ "era $uboot_startaddr $uboot_endaddr;" \ "cp.b $loadaddr $uboot_startaddr $filesize;" \ "protect on $uboot_startaddr $uboot_endaddr\0" \ "zapenv=protect off $env_startaddr $env_endaddr;" \ "era $env_startaddr $env_endaddr;" \ "protect on $env_startaddr $env_endaddr\0" #define CONFIG_BOOTDELAY 5 /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_ENV_OVERWRITE /* * Command line configuration. */ #include #define CONFIG_CMD_BSP #define CONFIG_CMD_DIAG #define CONFIG_CMD_ELF #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_FLASH #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_SDRAM /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #if 1 #define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ #endif #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif #define CONFIG_ETHADDR DE:AD:BE:EF:01:01 /* Ethernet address */ #define CONFIG_IPADDR 192.168.193.102 #define CONFIG_NETMASK 255.255.255.248 #define CONFIG_SERVERIP 192.168.193.99 #define CONFIG_STATUS_LED /* Status LED enabled */ #define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ #define STATUS_LED_BIT 0x00000001 #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) #define STATUS_LED_STATE STATUS_LED_BLINKING #define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ #define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ #ifndef __ASSEMBLY__ /* LEDs */ typedef unsigned int led_id_t; #define __led_toggle(_msk) \ do { \ *((volatile char *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \ } while(0) #define __led_set(_msk, _st) \ do { \ if ((_st)) \ *((volatile char *) (CONFIG_SYS_LED_BASE)) |= (_msk); \ else \ *((volatile char *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \ } while(0) #define __led_init(msk, st) __led_set(msk, st) #endif #define CONFIG_MISC_INIT_R #define CONFIG_SYS_LED_BASE 0xFFE80000 /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFFF00000 #define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 #define CONFIG_SYS_EUMB_ADDR 0xFCE00000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ #define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ /* Maximum amount of RAM. */ #define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 #if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE #undef CONFIG_SYS_RAMBOOT #else #define CONFIG_SYS_RAMBOOT #endif /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area */ /* Size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_SIZE 128 #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 #define CONFIG_SYS_INIT_RAM_END 0x1000 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) /* * NS16550 Configuration */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK 3686400 #define CONFIG_SYS_NS16550_COM1 0xFFF80000 /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. * For the detail description refer to the MPC8240 user's manual. */ #define CONFIG_SYS_CLK_FREQ 33000000 #define CONFIG_SYS_HZ 1000 #define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3 /* Bit-field values for MCCR1. */ #define CONFIG_SYS_ROMNAL 0 #define CONFIG_SYS_ROMFAL 7 /* Bit-field values for MCCR2. */ #define CONFIG_SYS_REFINT 430 /* Refresh interval */ /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ #define CONFIG_SYS_BSTOPRE 192 /* Bit-field values for MCCR3. */ #define CONFIG_SYS_REFREC 2 /* Refresh to activate interval */ #define CONFIG_SYS_RDLAT 3 /* Data latancy from read command */ /* Bit-field values for MCCR4. */ #define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */ #define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ #define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latancy */ #define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ #define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */ #define CONFIG_SYS_ACTORW 2 #define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 /* Memory bank settings. * Only bits 20-29 are actually used from these vales to set the * start/end addresses. The upper two bits will always be 0, and the lower * 20 bits will be 0x00000 for a start address, or 0xfffff for an end * address. Refer to the MPC8240 book. */ #define CONFIG_SYS_BANK0_START 0x00000000 #define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) #define CONFIG_SYS_BANK0_ENABLE 1 #define CONFIG_SYS_BANK1_START 0x3ff00000 #define CONFIG_SYS_BANK1_END 0x3fffffff #define CONFIG_SYS_BANK1_ENABLE 0 #define CONFIG_SYS_BANK2_START 0x3ff00000 #define CONFIG_SYS_BANK2_END 0x3fffffff #define CONFIG_SYS_BANK2_ENABLE 0 #define CONFIG_SYS_BANK3_START 0x3ff00000 #define CONFIG_SYS_BANK3_END 0x3fffffff #define CONFIG_SYS_BANK3_ENABLE 0 #define CONFIG_SYS_BANK4_START 0x3ff00000 #define CONFIG_SYS_BANK4_END 0x3fffffff #define CONFIG_SYS_BANK4_ENABLE 0 #define CONFIG_SYS_BANK5_START 0x3ff00000 #define CONFIG_SYS_BANK5_END 0x3fffffff #define CONFIG_SYS_BANK5_ENABLE 0 #define CONFIG_SYS_BANK6_START 0x3ff00000 #define CONFIG_SYS_BANK6_END 0x3fffffff #define CONFIG_SYS_BANK6_ENABLE 0 #define CONFIG_SYS_BANK7_START 0x3ff00000 #define CONFIG_SYS_BANK7_END 0x3fffffff #define CONFIG_SYS_BANK7_ENABLE 0 #define CONFIG_SYS_ODCR 0xff #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) #define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_IBAT3L (0xFC000000 | BATL_PP_10 | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT3U (0xFC000000 | BATU_BL_64M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ #define CONFIG_SYS_MAX_FLASH_SECT 256 /* Max number of sectors in one bank */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /* * Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ /* Warining: environment is not EMBEDDED in the U-Boot code. * It's stored in flash separately. */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR 0xFFF70000 #define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment */ #define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */ #define CONFIG_ENV_SECT_SIZE 0x40000 /* Size of the Environment Sector */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 32 #if defined(CONFIG_CMD_KGDB) # define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* we need Plug 'n Play */ #define CONFIG_NET_MULTI /* Multi ethernet cards support */ #define CONFIG_TULIP #define CONFIG_EEPRO100 #define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #endif /* __CONFIG_H */