From 1d9f410500f32b04b18b176386e77afacda7acfb Mon Sep 17 00:00:00 2001 From: wdenk Date: Sat, 9 Oct 2004 22:21:29 +0000 Subject: Patch by Steven Scholz, 16 Aug 2004: - Introducing the concept of SoCs "./cpu/$(CPU)/$(SOC)" - creating subdirs for SoCs ./cpu/arm920t/imx and ./cpu/arm920t/s3c24x0 - moving SoC specific code out of cpu/arm920t/ into cpu/arm920t/$(SOC)/ - moving drivers/s3c24x0_i2c.c and drivers/serial_imx.c out of drivers/ into cpu/arm920t/$(SOC)/ diff --git a/CHANGELOG b/CHANGELOG index 82b473f..702a1c7 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,13 @@ Changes since U-Boot 1.1.1: ====================================================================== +* Patch by Steven Scholz, 16 Aug 2004: + - Introducing the concept of SoCs "./cpu/$(CPU)/$(SOC)" + - creating subdirs for SoCs ./cpu/arm920t/imx and ./cpu/arm920t/s3c24x0 + - moving SoC specific code out of cpu/arm920t/ into cpu/arm920t/$(SOC)/ + - moving drivers/s3c24x0_i2c.c and drivers/serial_imx.c out of drivers/ + into cpu/arm920t/$(SOC)/ + * Patches by Sean Chang, 09 Aug 2004: - Added support for both 8 and 16 bit mode access to System ACE CF through MPU. diff --git a/Makefile b/Makefile index 461fd82..8c3ff7e 100644 --- a/Makefile +++ b/Makefile @@ -45,7 +45,7 @@ export TOPDIR ifeq (include/config.mk,$(wildcard include/config.mk)) # load ARCH, BOARD, and CPU configuration include include/config.mk -export ARCH CPU BOARD VENDOR +export ARCH CPU BOARD VENDOR SOC # load other configuration include $(TOPDIR)/config.mk @@ -101,6 +101,9 @@ endif LIBS = lib_generic/libgeneric.a LIBS += board/$(BOARDDIR)/lib$(BOARD).a LIBS += cpu/$(CPU)/lib$(CPU).a +ifdef SOC +LIBS += cpu/$(CPU)/$(SOC)/lib$(SOC).a +endif LIBS += lib_$(ARCH)/lib$(ARCH).a LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a \ fs/reiserfs/libreiserfs.a @@ -1175,10 +1178,10 @@ lpd7a404_config: unconfig @./mkconfig $(@:_config=) arm lh7a40x lpd7a40x mx1ads_config : unconfig - @./mkconfig $(@:_config=) arm arm920t mx1ads + @./mkconfig $(@:_config=) arm arm920t mx1ads NULL imx mx1fs2_config : unconfig - @./mkconfig $(@:_config=) arm arm920t mx1fs2 + @./mkconfig $(@:_config=) arm arm920t mx1fs2 NULL imx omap1510inn_config : unconfig @./mkconfig $(@:_config=) arm arm925t omap1510inn @@ -1219,13 +1222,13 @@ omap730p2_cs3boot_config : unconfig @./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 scb9328_config : unconfig - @./mkconfig $(@:_config=) arm arm920t scb9328 + @./mkconfig $(@:_config=) arm arm920t scb9328 NULL imx smdk2400_config : unconfig - @./mkconfig $(@:_config=) arm arm920t smdk2400 + @./mkconfig $(@:_config=) arm arm920t smdk2400 NULL s3c24x0 smdk2410_config : unconfig - @./mkconfig $(@:_config=) arm arm920t smdk2410 + @./mkconfig $(@:_config=) arm arm920t smdk2410 NULL s3c24x0 SX1_config : unconfig @./mkconfig $(@:_config=) arm arm925t sx1 @@ -1253,10 +1256,10 @@ trab_old_config: unconfig echo "... with 8 MB Flash, 16 MB RAM" ; \ echo "TEXT_BASE = 0x0CF40000" >board/trab/config.tmp ; \ } - @./mkconfig -a $(call xtract_trab,$@) arm arm920t trab + @./mkconfig -a $(call xtract_trab,$@) arm arm920t trab NULL s3c24x0 VCMA9_config : unconfig - @./mkconfig $(@:_config=) arm arm920t vcma9 mpl + @./mkconfig $(@:_config=) arm arm920t vcma9 mpl s3c24x0 versatile_config : unconfig @./mkconfig $(@:_config=) arm arm926ejs versatile diff --git a/README b/README index 4485b51..43539a9 100644 --- a/README +++ b/README @@ -125,6 +125,8 @@ Directory Hierarchy: - 74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs - arm720t Files specific to ARM 720 CPUs - arm920t Files specific to ARM 920 CPUs + - imx Files specific to Motorola MC9328 i.MX CPUs + - s3c24x0 Files specific to Samsung S3C24X0 CPUs - arm925t Files specific to ARM 925 CPUs - arm926ejs Files specific to ARM 926 CPUs - at91rm9200 Files specific to Atmel AT91RM9200 CPUs diff --git a/config.mk b/config.mk index 2182391..75bbac5 100644 --- a/config.mk +++ b/config.mk @@ -59,6 +59,9 @@ endif ifdef CPU sinclude $(TOPDIR)/cpu/$(CPU)/config.mk # include CPU specific rules endif +ifdef SOC +sinclude $(TOPDIR)/cpu/$(CPU)/$(SOC)/config.mk # include SoC specific rules +endif ifdef VENDOR BOARDDIR = $(VENDOR)/$(BOARD) else diff --git a/cpu/arm920t/Makefile b/cpu/arm920t/Makefile index 68a33d6..8f256e9 100644 --- a/cpu/arm920t/Makefile +++ b/cpu/arm920t/Makefile @@ -26,11 +26,7 @@ include $(TOPDIR)/config.mk LIB = lib$(CPU).a START = start.o -OBJS = cpu.o \ - imx_generic.o imx_interrupts.o imx_speed.o \ - interrupts.o \ - s3c24x0_interrupts.o s3c24x0_serial.o s3c24x0_speed.o \ - usb_ohci.o +OBJS = cpu.o interrupts.o all: .depend $(START) $(LIB) diff --git a/cpu/arm920t/imx/Makefile b/cpu/arm920t/imx/Makefile new file mode 100644 index 0000000..8865f82 --- /dev/null +++ b/cpu/arm920t/imx/Makefile @@ -0,0 +1,42 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(SOC).a + +OBJS = generic.o interrupts.o serial.o speed.o + +all: .depend $(LIB) + +$(LIB): $(OBJS) + $(AR) crv $@ $(OBJS) + +######################################################################### + +.depend: Makefile $(OBJS:.o=.c) + $(CC) -M $(CFLAGS) $(OBJS:.o=.c) > $@ + +sinclude .depend + +######################################################################### diff --git a/cpu/arm920t/imx/generic.c b/cpu/arm920t/imx/generic.c new file mode 100644 index 0000000..aa7c8c1 --- /dev/null +++ b/cpu/arm920t/imx/generic.c @@ -0,0 +1,90 @@ +/* + * arch/arm/mach-imx/generic.c + * + * author: Sascha Hauer + * Created: april 20th, 2004 + * Copyright: Synertronixx GmbH + * + * Common code for i.MX machines + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include + +#ifdef CONFIG_IMX + +#include + +void imx_gpio_mode(int gpio_mode) +{ + unsigned int pin = gpio_mode & GPIO_PIN_MASK; + unsigned int port = (gpio_mode & GPIO_PORT_MASK) >> 5; + unsigned int ocr = (gpio_mode & GPIO_OCR_MASK) >> 10; + unsigned int tmp; + + /* Pullup enable */ + if(gpio_mode & GPIO_PUEN) + PUEN(port) |= (1< + * Marius Groeger + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Alex Zuepke + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#if defined (CONFIG_IMX) + +#include +#include + +int interrupt_init (void) +{ + int i; + /* setup GP Timer 1 */ + TCTL1 = TCTL_SWR; + for ( i=0; i<100; i++) TCTL1 = 0; /* We have no udelay by now */ + TPRER1 = get_PERCLK1() / 1000000; /* 1 MHz */ + TCTL1 |= TCTL_FRR | (1<<1); /* Freerun Mode, PERCLK1 input */ + + reset_timer_masked(); + + return (0); +} + +/* + * timer without interrupts + */ + +void reset_timer (void) +{ + reset_timer_masked (); +} + +ulong get_timer (ulong base) +{ + return get_timer_masked (); +} + +void set_timer (ulong t) +{ + /* nop */ +} + +void reset_timer_masked (void) +{ + TCTL1 &= ~TCTL_TEN; + TCTL1 |= TCTL_TEN; /* Enable timer */ +} + +ulong get_timer_masked (void) +{ + return TCN1; +} + +void udelay_masked (unsigned long usec) +{ + ulong start = get_timer_masked(); + + while (get_timer_masked () - start < usec ) + /*NOP*/; +} + +void udelay (unsigned long usec) +{ + udelay_masked(usec); +} + +/* + * This function is derived from PowerPC code (read timebase as long long). + * On ARM it just returns the timer value. + */ +unsigned long long get_ticks(void) +{ + return get_timer(0); +} + +/* + * This function is derived from PowerPC code (timebase clock frequency). + * On ARM it returns the number of timer ticks per second. + */ +ulong get_tbclk (void) +{ + ulong tbclk; + + tbclk = CFG_HZ; + + return tbclk; +} + +#endif /* defined (CONFIG_IMX) */ diff --git a/cpu/arm920t/imx/serial.c b/cpu/arm920t/imx/serial.c new file mode 100644 index 0000000..9dbaa56 --- /dev/null +++ b/cpu/arm920t/imx/serial.c @@ -0,0 +1,201 @@ +/* + * (c) 2004 Sascha Hauer + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include +#if defined (CONFIG_IMX) + +#include + +#ifndef CONFIG_IMX_SERIAL_NONE + +#if defined CONFIG_IMX_SERIAL1 +#define UART_BASE IMX_UART1_BASE +#elif defined CONFIG_IMX_SERIAL2 +#define UART_BASE IMX_UART2_BASE +#else +#error "define CONFIG_IMX_SERIAL1, CONFIG_IMX_SERIAL2 or CONFIG_IMX_SERIAL_NONE" +#endif + +struct imx_serial { + volatile uint32_t urxd[16]; + volatile uint32_t utxd[16]; + volatile uint32_t ucr1; + volatile uint32_t ucr2; + volatile uint32_t ucr3; + volatile uint32_t ucr4; + volatile uint32_t ufcr; + volatile uint32_t usr1; + volatile uint32_t usr2; + volatile uint32_t uesc; + volatile uint32_t utim; + volatile uint32_t ubir; + volatile uint32_t ubmr; + volatile uint32_t ubrc; + volatile uint32_t bipr[4]; + volatile uint32_t bmpr[4]; + volatile uint32_t uts; +}; + +void serial_setbrg (void) +{ + serial_init(); +} + +extern void imx_gpio_mode(int gpio_mode); + +/* + * Initialise the serial port with the given baudrate. The settings + * are always 8 data bits, no parity, 1 stop bit, no start bits. + * + */ +int serial_init (void) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; +#ifdef CONFIG_IMX_SERIAL1 + imx_gpio_mode(PC11_PF_UART1_TXD); + imx_gpio_mode(PC12_PF_UART1_RXD); +#else + imx_gpio_mode(PB30_PF_UART2_TXD); + imx_gpio_mode(PB31_PF_UART2_RXD); +#endif + + /* Disable UART */ + base->ucr1 &= ~UCR1_UARTEN; + + /* Set to default POR state */ + + base->ucr1 = 0x00000004; + base->ucr2 = 0x00000000; + base->ucr3 = 0x00000000; + base->ucr4 = 0x00008040; + base->uesc = 0x0000002B; + base->utim = 0x00000000; + base->ubir = 0x00000000; + base->ubmr = 0x00000000; + base->uts = 0x00000000; + /* Set clocks */ + base->ucr4 |= UCR4_REF16; + + /* Configure FIFOs */ + base->ufcr = 0xa81; + + /* Set the numerator value minus one of the BRM ratio */ + base->ubir = (CONFIG_BAUDRATE / 100) - 1; + + /* Set the denominator value minus one of the BRM ratio */ + base->ubmr = 10000 - 1; + + /* Set to 8N1 */ + base->ucr2 &= ~UCR2_PREN; + base->ucr2 |= UCR2_WS; + base->ucr2 &= ~UCR2_STPB; + + /* Ignore RTS */ + base->ucr2 |= UCR2_IRTS; + + /* Enable UART */ + base->ucr1 |= UCR1_UARTEN | UCR1_UARTCLKEN; + + /* Enable FIFOs */ + base->ucr2 |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN; + + /* Clear status flags */ + base->usr2 |= USR2_ADET | + USR2_DTRF | + USR2_IDLE | + USR2_IRINT | + USR2_WAKE | + USR2_RTSF | + USR2_BRCD | + USR2_ORE | + USR2_RDR; + + /* Clear status flags */ + base->usr1 |= USR1_PARITYERR | + USR1_RTSD | + USR1_ESCF | + USR1_FRAMERR | + USR1_AIRINT | + USR1_AWAKE; + return (0); +} + +/* + * Read a single byte from the serial port. Returns 1 on success, 0 + * otherwise. When the function is successful, the character read is + * written into its argument c. + */ +int serial_getc (void) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; + unsigned char ch; + + while(base->uts & UTS_RXEMPTY); + + ch = (char)base->urxd[0]; + + return ch; +} + +#ifdef CONFIG_HWFLOW +static int hwflow = 0; /* turned off by default */ +int hwflow_onoff(int on) +{ +} +#endif + +/* + * Output a single byte to the serial port. + */ +void serial_putc (const char c) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; + + /* Wait for Tx FIFO not full */ + while (base->uts & UTS_TXFULL); + + base->utxd[0] = c; + + /* If \n, also do \r */ + if (c == '\n') + serial_putc ('\r'); +} + +/* + * Test whether a character is in the RX buffer + */ +int serial_tstc (void) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; + + /* If receive fifo is empty, return false */ + if (base->uts & UTS_RXEMPTY) + return 0; + return 1; +} + +void +serial_puts (const char *s) +{ + while (*s) { + serial_putc (*s++); + } +} +#endif /* CONFIG_IMX_SERIAL_NONE */ +#endif /* defined CONFIG_IMX */ diff --git a/cpu/arm920t/imx/speed.c b/cpu/arm920t/imx/speed.c new file mode 100644 index 0000000..1e29698 --- /dev/null +++ b/cpu/arm920t/imx/speed.c @@ -0,0 +1,102 @@ +/* + * + * (c) 2004 Sascha Hauer + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#include +#if defined (CONFIG_IMX) + +#include + +/* ------------------------------------------------------------------------- */ +/* NOTE: This describes the proper use of this file. + * + * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL. + * SH FIXME: 16780000 in our case + * get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of + * the specified bus in HZ. + */ +/* ------------------------------------------------------------------------- */ + +ulong get_systemPLLCLK(void) +{ + /* FIXME: We assume System_SEL = 0 here */ + u32 spctl0 = SPCTL0; + u32 mfi = (spctl0 >> 10) & 0xf; + u32 mfn = spctl0 & 0x3f; + u32 mfd = (spctl0 >> 16) & 0x3f; + u32 pd = (spctl0 >> 26) & 0xf; + + mfi = mfi<=5 ? 5 : mfi; + + return (2*(CONFIG_SYSPLL_CLK_FREQ>>10)*( (mfi<<10) + (mfn<<10)/(mfd+1)))/(pd+1); +} + +ulong get_mcuPLLCLK(void) +{ + /* FIXME: We assume System_SEL = 0 here */ + u32 mpctl0 = MPCTL0; + u32 mfi = (mpctl0 >> 10) & 0xf; + u32 mfn = mpctl0 & 0x3f; + u32 mfd = (mpctl0 >> 16) & 0x3f; + u32 pd = (mpctl0 >> 26) & 0xf; + + mfi = mfi<=5 ? 5 : mfi; + + return (2*(CONFIG_SYS_CLK_FREQ>>10)*( (mfi<<10) + (mfn<<10)/(mfd+1)))/(pd+1); +} + +ulong get_FCLK(void) +{ + return (( CSCR>>15)&1) ? get_mcuPLLCLK()>>1 : get_mcuPLLCLK(); +} + +/* return HCLK frequency */ +ulong get_HCLK(void) +{ + u32 bclkdiv = (( CSCR >> 10 ) & 0xf) + 1; + printf("bclkdiv: %d\n", bclkdiv); + return get_systemPLLCLK() / bclkdiv; +} + +/* return BCLK frequency */ +ulong get_BCLK(void) +{ + return get_HCLK(); +} + +ulong get_PERCLK1(void) +{ + return get_systemPLLCLK() / (((PCDR) & 0xf)+1); +} + +ulong get_PERCLK2(void) +{ + return get_systemPLLCLK() / (((PCDR>>4) & 0xf)+1); +} + +ulong get_PERCLK3(void) +{ + return get_systemPLLCLK() / (((PCDR>>16) & 0x7f)+1); +} + +#endif /* defined (CONFIG_IMX) */ diff --git a/cpu/arm920t/imx_generic.c b/cpu/arm920t/imx_generic.c deleted file mode 100644 index aa7c8c1..0000000 --- a/cpu/arm920t/imx_generic.c +++ /dev/null @@ -1,90 +0,0 @@ -/* - * arch/arm/mach-imx/generic.c - * - * author: Sascha Hauer - * Created: april 20th, 2004 - * Copyright: Synertronixx GmbH - * - * Common code for i.MX machines - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#include - -#ifdef CONFIG_IMX - -#include - -void imx_gpio_mode(int gpio_mode) -{ - unsigned int pin = gpio_mode & GPIO_PIN_MASK; - unsigned int port = (gpio_mode & GPIO_PORT_MASK) >> 5; - unsigned int ocr = (gpio_mode & GPIO_OCR_MASK) >> 10; - unsigned int tmp; - - /* Pullup enable */ - if(gpio_mode & GPIO_PUEN) - PUEN(port) |= (1< - * Marius Groeger - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Alex Zuepke - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#if defined (CONFIG_IMX) - -#include -#include - -int interrupt_init (void) -{ - int i; - /* setup GP Timer 1 */ - TCTL1 = TCTL_SWR; - for ( i=0; i<100; i++) TCTL1 = 0; /* We have no udelay by now */ - TPRER1 = get_PERCLK1() / 1000000; /* 1 MHz */ - TCTL1 |= TCTL_FRR | (1<<1); /* Freerun Mode, PERCLK1 input */ - - reset_timer_masked(); - - return (0); -} - -/* - * timer without interrupts - */ - -void reset_timer (void) -{ - reset_timer_masked (); -} - -ulong get_timer (ulong base) -{ - return get_timer_masked (); -} - -void set_timer (ulong t) -{ - /* nop */ -} - -void reset_timer_masked (void) -{ - TCTL1 &= ~TCTL_TEN; - TCTL1 |= TCTL_TEN; /* Enable timer */ -} - -ulong get_timer_masked (void) -{ - return TCN1; -} - -void udelay_masked (unsigned long usec) -{ - ulong start = get_timer_masked(); - - while (get_timer_masked () - start < usec ) - /*NOP*/; -} - -void udelay (unsigned long usec) -{ - udelay_masked(usec); -} - -/* - * This function is derived from PowerPC code (read timebase as long long). - * On ARM it just returns the timer value. - */ -unsigned long long get_ticks(void) -{ - return get_timer(0); -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk (void) -{ - ulong tbclk; - - tbclk = CFG_HZ; - - return tbclk; -} - -#endif /* defined (CONFIG_IMX) */ diff --git a/cpu/arm920t/imx_speed.c b/cpu/arm920t/imx_speed.c deleted file mode 100644 index 1e29698..0000000 --- a/cpu/arm920t/imx_speed.c +++ /dev/null @@ -1,102 +0,0 @@ -/* - * - * (c) 2004 Sascha Hauer - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - - -#include -#if defined (CONFIG_IMX) - -#include - -/* ------------------------------------------------------------------------- */ -/* NOTE: This describes the proper use of this file. - * - * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL. - * SH FIXME: 16780000 in our case - * get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of - * the specified bus in HZ. - */ -/* ------------------------------------------------------------------------- */ - -ulong get_systemPLLCLK(void) -{ - /* FIXME: We assume System_SEL = 0 here */ - u32 spctl0 = SPCTL0; - u32 mfi = (spctl0 >> 10) & 0xf; - u32 mfn = spctl0 & 0x3f; - u32 mfd = (spctl0 >> 16) & 0x3f; - u32 pd = (spctl0 >> 26) & 0xf; - - mfi = mfi<=5 ? 5 : mfi; - - return (2*(CONFIG_SYSPLL_CLK_FREQ>>10)*( (mfi<<10) + (mfn<<10)/(mfd+1)))/(pd+1); -} - -ulong get_mcuPLLCLK(void) -{ - /* FIXME: We assume System_SEL = 0 here */ - u32 mpctl0 = MPCTL0; - u32 mfi = (mpctl0 >> 10) & 0xf; - u32 mfn = mpctl0 & 0x3f; - u32 mfd = (mpctl0 >> 16) & 0x3f; - u32 pd = (mpctl0 >> 26) & 0xf; - - mfi = mfi<=5 ? 5 : mfi; - - return (2*(CONFIG_SYS_CLK_FREQ>>10)*( (mfi<<10) + (mfn<<10)/(mfd+1)))/(pd+1); -} - -ulong get_FCLK(void) -{ - return (( CSCR>>15)&1) ? get_mcuPLLCLK()>>1 : get_mcuPLLCLK(); -} - -/* return HCLK frequency */ -ulong get_HCLK(void) -{ - u32 bclkdiv = (( CSCR >> 10 ) & 0xf) + 1; - printf("bclkdiv: %d\n", bclkdiv); - return get_systemPLLCLK() / bclkdiv; -} - -/* return BCLK frequency */ -ulong get_BCLK(void) -{ - return get_HCLK(); -} - -ulong get_PERCLK1(void) -{ - return get_systemPLLCLK() / (((PCDR) & 0xf)+1); -} - -ulong get_PERCLK2(void) -{ - return get_systemPLLCLK() / (((PCDR>>4) & 0xf)+1); -} - -ulong get_PERCLK3(void) -{ - return get_systemPLLCLK() / (((PCDR>>16) & 0x7f)+1); -} - -#endif /* defined (CONFIG_IMX) */ diff --git a/cpu/arm920t/s3c24x0/Makefile b/cpu/arm920t/s3c24x0/Makefile new file mode 100644 index 0000000..af9e4ef --- /dev/null +++ b/cpu/arm920t/s3c24x0/Makefile @@ -0,0 +1,43 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(SOC).a + +OBJS = i2c.o interrupts.o serial.o speed.o \ + usb_ohci.o + +all: .depend $(LIB) + +$(LIB): $(OBJS) + $(AR) crv $@ $(OBJS) + +######################################################################### + +.depend: Makefile $(OBJS:.o=.c) + $(CC) -M $(CFLAGS) $(OBJS:.o=.c) > $@ + +sinclude .depend + +######################################################################### diff --git a/cpu/arm920t/s3c24x0/i2c.c b/cpu/arm920t/s3c24x0/i2c.c new file mode 100644 index 0000000..ef56cd1 --- /dev/null +++ b/cpu/arm920t/s3c24x0/i2c.c @@ -0,0 +1,447 @@ +/* + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, d.mueller@elsoft.ch + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* This code should work for both the S3C2400 and the S3C2410 + * as they seem to have the same I2C controller inside. + * The different address mapping is handled by the s3c24xx.h files below. + */ + +#include + +#ifdef CONFIG_DRIVER_S3C24X0_I2C + +#if defined(CONFIG_S3C2400) +#include +#elif defined(CONFIG_S3C2410) +#include +#endif +#include + +#ifdef CONFIG_HARD_I2C + +#define I2C_WRITE 0 +#define I2C_READ 1 + +#define I2C_OK 0 +#define I2C_NOK 1 +#define I2C_NACK 2 +#define I2C_NOK_LA 3 /* Lost arbitration */ +#define I2C_NOK_TOUT 4 /* time out */ + +#define I2CSTAT_BSY 0x20 /* Busy bit */ +#define I2CSTAT_NACK 0x01 /* Nack bit */ +#define I2CCON_IRPND 0x10 /* Interrupt pending bit */ +#define I2C_MODE_MT 0xC0 /* Master Transmit Mode */ +#define I2C_MODE_MR 0x80 /* Master Receive Mode */ +#define I2C_START_STOP 0x20 /* START / STOP */ +#define I2C_TXRX_ENA 0x10 /* I2C Tx/Rx enable */ + +#define I2C_TIMEOUT 1 /* 1 second */ + + +static int GetI2CSDA(void) +{ + S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO(); + +#ifdef CONFIG_S3C2410 + return (gpio->GPEDAT & 0x8000) >> 15; +#endif +#ifdef CONFIG_S3C2400 + return (gpio->PGDAT & 0x0020) >> 5; +#endif +} + +#if 0 +static void SetI2CSDA(int x) +{ + rGPEDAT = (rGPEDAT & ~0x8000) | (x&1) << 15; +} +#endif + +static void SetI2CSCL(int x) +{ + S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO(); + +#ifdef CONFIG_S3C2410 + gpio->GPEDAT = (gpio->GPEDAT & ~0x4000) | (x&1) << 14; +#endif +#ifdef CONFIG_S3C2400 + gpio->PGDAT = (gpio->PGDAT & ~0x0040) | (x&1) << 6; +#endif +} + + +static int WaitForXfer (void) +{ + S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); + int i, status; + + i = I2C_TIMEOUT * 10000; + status = i2c->IICCON; + while ((i > 0) && !(status & I2CCON_IRPND)) { + udelay (100); + status = i2c->IICCON; + i--; + } + + return (status & I2CCON_IRPND) ? I2C_OK : I2C_NOK_TOUT; +} + +static int IsACK (void) +{ + S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); + + return (!(i2c->IICSTAT & I2CSTAT_NACK)); +} + +static void ReadWriteByte (void) +{ + S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); + + i2c->IICCON &= ~I2CCON_IRPND; +} + +void i2c_init (int speed, int slaveadd) +{ + S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); + S3C24X0_GPIO *const gpio = S3C24X0_GetBase_GPIO (); + ulong freq, pres = 16, div; + int i, status; + + /* wait for some time to give previous transfer a chance to finish */ + + i = I2C_TIMEOUT * 1000; + status = i2c->IICSTAT; + while ((i > 0) && (status & I2CSTAT_BSY)) { + udelay (1000); + status = i2c->IICSTAT; + i--; + } + + if ((status & I2CSTAT_BSY) || GetI2CSDA () == 0) { +#ifdef CONFIG_S3C2410 + ulong old_gpecon = gpio->GPECON; +#endif +#ifdef CONFIG_S3C2400 + ulong old_gpecon = gpio->PGCON; +#endif + /* bus still busy probably by (most) previously interrupted transfer */ + +#ifdef CONFIG_S3C2410 + /* set I2CSDA and I2CSCL (GPE15, GPE14) to GPIO */ + gpio->GPECON = (gpio->GPECON & ~0xF0000000) | 0x10000000; +#endif +#ifdef CONFIG_S3C2400 + /* set I2CSDA and I2CSCL (PG5, PG6) to GPIO */ + gpio->PGCON = (gpio->PGCON & ~0x00003c00) | 0x00000c00; +#endif + + /* toggle I2CSCL until bus idle */ + SetI2CSCL (0); + udelay (1000); + i = 10; + while ((i > 0) && (GetI2CSDA () != 1)) { + SetI2CSCL (1); + udelay (1000); + SetI2CSCL (0); + udelay (1000); + i--; + } + SetI2CSCL (1); + udelay (1000); + + /* restore pin functions */ +#ifdef CONFIG_S3C2410 + gpio->GPECON = old_gpecon; +#endif +#ifdef CONFIG_S3C2400 + gpio->PGCON = old_gpecon; +#endif + } + + /* calculate prescaler and divisor values */ + freq = get_PCLK (); + if ((freq / pres / (16 + 1)) > speed) + /* set prescaler to 512 */ + pres = 512; + + div = 0; + while ((freq / pres / (div + 1)) > speed) + div++; + + /* set prescaler, divisor according to freq, also set + * ACKGEN, IRQ */ + i2c->IICCON = (div & 0x0F) | 0xA0 | ((pres == 512) ? 0x40 : 0); + + /* init to SLAVE REVEIVE and set slaveaddr */ + i2c->IICSTAT = 0; + i2c->IICADD = slaveadd; + /* program Master Transmit (and implicit STOP) */ + i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA; + +} + +/* + * cmd_type is 0 for write, 1 for read. + * + * addr_len can take any value from 0-255, it is only limited + * by the char, we could make it larger if needed. If it is + * 0 we skip the address write cycle. + */ +static +int i2c_transfer (unsigned char cmd_type, + unsigned char chip, + unsigned char addr[], + unsigned char addr_len, + unsigned char data[], unsigned short data_len) +{ + S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); + int i, status, result; + + if (data == 0 || data_len == 0) { + /*Don't support data transfer of no length or to address 0 */ + printf ("i2c_transfer: bad call\n"); + return I2C_NOK; + } + + /* Check I2C bus idle */ + i = I2C_TIMEOUT * 1000; + status = i2c->IICSTAT; + while ((i > 0) && (status & I2CSTAT_BSY)) { + udelay (1000); + status = i2c->IICSTAT; + i--; + } + + if (status & I2CSTAT_BSY) + return I2C_NOK_TOUT; + + i2c->IICCON |= 0x80; + result = I2C_OK; + + switch (cmd_type) { + case I2C_WRITE: + if (addr && addr_len) { + i2c->IICDS = chip; + /* send START */ + i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP; + i = 0; + while ((i < addr_len) && (result == I2C_OK)) { + result = WaitForXfer (); + i2c->IICDS = addr[i]; + ReadWriteByte (); + i++; + } + i = 0; + while ((i < data_len) && (result == I2C_OK)) { + result = WaitForXfer (); + i2c->IICDS = data[i]; + ReadWriteByte (); + i++; + } + } else { + i2c->IICDS = chip; + /* send START */ + i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP; + i = 0; + while ((i < data_len) && (result = I2C_OK)) { + result = WaitForXfer (); + i2c->IICDS = data[i]; + ReadWriteByte (); + i++; + } + } + + if (result == I2C_OK) + result = WaitForXfer (); + + /* send STOP */ + i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA; + ReadWriteByte (); + break; + + case I2C_READ: + if (addr && addr_len) { + i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA; + i2c->IICDS = chip; + /* send START */ + i2c->IICSTAT |= I2C_START_STOP; + result = WaitForXfer (); + if (IsACK ()) { + i = 0; + while ((i < addr_len) && (result == I2C_OK)) { + i2c->IICDS = addr[i]; + ReadWriteByte (); + result = WaitForXfer (); + i++; + } + + i2c->IICDS = chip; + /* resend START */ + i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA | + I2C_START_STOP; + ReadWriteByte (); + result = WaitForXfer (); + i = 0; + while ((i < data_len) && (result == I2C_OK)) { + /* disable ACK for final READ */ + if (i == data_len - 1) + i2c->IICCON &= ~0x80; + ReadWriteByte (); + result = WaitForXfer (); + data[i] = i2c->IICDS; + i++; + } + } else { + result = I2C_NACK; + } + + } else { + i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA; + i2c->IICDS = chip; + /* send START */ + i2c->IICSTAT |= I2C_START_STOP; + result = WaitForXfer (); + + if (IsACK ()) { + i = 0; + while ((i < data_len) && (result == I2C_OK)) { + /* disable ACK for final READ */ + if (i == data_len - 1) + i2c->IICCON &= ~0x80; + ReadWriteByte (); + result = WaitForXfer (); + data[i] = i2c->IICDS; + i++; + } + } else { + result = I2C_NACK; + } + } + + /* send STOP */ + i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA; + ReadWriteByte (); + break; + + default: + printf ("i2c_transfer: bad call\n"); + result = I2C_NOK; + break; + } + + return (result); +} + +int i2c_probe (uchar chip) +{ + uchar buf[1]; + + buf[0] = 0; + + /* + * What is needed is to send the chip address and verify that the + * address was ed (i.e. there was a chip at that address which + * drove the data line low). + */ + return (i2c_transfer (I2C_READ, chip << 1, 0, 0, buf, 1) != I2C_OK); +} + +int i2c_read (uchar chip, uint addr, int alen, uchar * buffer, int len) +{ + uchar xaddr[4]; + int ret; + + if (alen > 4) { + printf ("I2C read: addr len %d not supported\n", alen); + return 1; + } + + if (alen > 0) { + xaddr[0] = (addr >> 24) & 0xFF; + xaddr[1] = (addr >> 16) & 0xFF; + xaddr[2] = (addr >> 8) & 0xFF; + xaddr[3] = addr & 0xFF; + } + +#ifdef CFG_I2C_EEPROM_ADDR_OVERFLOW + /* + * EEPROM chips that implement "address overflow" are ones + * like Catalyst 24WC04/08/16 which has 9/10/11 bits of + * address and the extra bits end up in the "chip address" + * bit slots. This makes a 24WC08 (1Kbyte) chip look like + * four 256 byte chips. + * + * Note that we consider the length of the address field to + * still be one byte because the extra address bits are + * hidden in the chip address. + */ + if (alen > 0) + chip |= ((addr >> (alen * 8)) & CFG_I2C_EEPROM_ADDR_OVERFLOW); +#endif + if ((ret = + i2c_transfer (I2C_READ, chip << 1, &xaddr[4 - alen], alen, + buffer, len)) != 0) { + printf ("I2c read: failed %d\n", ret); + return 1; + } + return 0; +} + +int i2c_write (uchar chip, uint addr, int alen, uchar * buffer, int len) +{ + uchar xaddr[4]; + + if (alen > 4) { + printf ("I2C write: addr len %d not supported\n", alen); + return 1; + } + + if (alen > 0) { + xaddr[0] = (addr >> 24) & 0xFF; + xaddr[1] = (addr >> 16) & 0xFF; + xaddr[2] = (addr >> 8) & 0xFF; + xaddr[3] = addr & 0xFF; + } +#ifdef CFG_I2C_EEPROM_ADDR_OVERFLOW + /* + * EEPROM chips that implement "address overflow" are ones + * like Catalyst 24WC04/08/16 which has 9/10/11 bits of + * address and the extra bits end up in the "chip address" + * bit slots. This makes a 24WC08 (1Kbyte) chip look like + * four 256 byte chips. + * + * Note that we consider the length of the address field to + * still be one byte because the extra address bits are + * hidden in the chip address. + */ + if (alen > 0) + chip |= ((addr >> (alen * 8)) & CFG_I2C_EEPROM_ADDR_OVERFLOW); +#endif + return (i2c_transfer + (I2C_WRITE, chip << 1, &xaddr[4 - alen], alen, buffer, + len) != 0); +} +#endif /* CONFIG_HARD_I2C */ + +#endif /* CONFIG_DRIVER_S3C24X0_I2C */ diff --git a/cpu/arm920t/s3c24x0/interrupts.c b/cpu/arm920t/s3c24x0/interrupts.c new file mode 100644 index 0000000..92298b0 --- /dev/null +++ b/cpu/arm920t/s3c24x0/interrupts.c @@ -0,0 +1,180 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Alex Zuepke + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) + +#include +#if defined(CONFIG_S3C2400) +#include +#elif defined(CONFIG_S3C2410) +#include +#endif + +extern void reset_cpu(ulong addr); +int timer_load_val = 0; + +/* macro to read the 16 bit timer */ +static inline ulong READ_TIMER(void) +{ + S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); + + return (timers->TCNTO4 & 0xffff); +} + +static ulong timestamp; +static ulong lastdec; + +int interrupt_init (void) +{ + S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); + + /* use PWM Timer 4 because it has no output */ + /* prescaler for Timer 4 is 16 */ + timers->TCFG0 = 0x0f00; + if (timer_load_val == 0) + { + /* + * for 10 ms clock period @ PCLK with 4 bit divider = 1/2 + * (default) and prescaler = 16. Should be 10390 + * @33.25MHz and 15625 @ 50 MHz + */ + timer_load_val = get_PCLK()/(2 * 16 * 100); + } + /* load value for 10 ms timeout */ + lastdec = timers->TCNTB4 = timer_load_val; + /* auto load, manual update of Timer 4 */ + timers->TCON = (timers->TCON & ~0x0700000) | 0x600000; + /* auto load, start Timer 4 */ + timers->TCON = (timers->TCON & ~0x0700000) | 0x500000; + timestamp = 0; + + return (0); +} + +/* + * timer without interrupts + */ + +void reset_timer (void) +{ + reset_timer_masked (); +} + +ulong get_timer (ulong base) +{ + return get_timer_masked () - base; +} + +void set_timer (ulong t) +{ + timestamp = t; +} + +void udelay (unsigned long usec) +{ + ulong tmo; + ulong start = get_timer(0); + + tmo = usec / 1000; + tmo *= (timer_load_val * 100); + tmo /= 1000; + + while ((ulong)(get_timer_masked () - start) < tmo) + /*NOP*/; +} + +void reset_timer_masked (void) +{ + /* reset time */ + lastdec = READ_TIMER(); + timestamp = 0; +} + +ulong get_timer_masked (void) +{ + ulong now = READ_TIMER(); + + if (lastdec >= now) { + /* normal mode */ + timestamp += lastdec - now; + } else { + /* we have an overflow ... */ + timestamp += lastdec + timer_load_val - now; + } + lastdec = now; + + return timestamp; +} + +void udelay_masked (unsigned long usec) +{ + ulong tmo; + + tmo = usec / 1000; + tmo *= (timer_load_val * 100); + tmo /= 1000; + + reset_timer_masked (); + + while (get_timer_masked () < tmo) + /*NOP*/; +} + +/* + * This function is derived from PowerPC code (read timebase as long long). + * On ARM it just returns the timer value. + */ +unsigned long long get_ticks(void) +{ + return get_timer(0); +} + +/* + * This function is derived from PowerPC code (timebase clock frequency). + * On ARM it returns the number of timer ticks per second. + */ +ulong get_tbclk (void) +{ + ulong tbclk; + +#if defined(CONFIG_SMDK2400) || defined(CONFIG_TRAB) + tbclk = timer_load_val * 100; +#elif defined(CONFIG_SMDK2410) || defined(CONFIG_VCMA9) + tbclk = CFG_HZ; +#else +# error "tbclk not configured" +#endif + + return tbclk; +} + +#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/s3c24x0/serial.c b/cpu/arm920t/s3c24x0/serial.c new file mode 100644 index 0000000..8327443 --- /dev/null +++ b/cpu/arm920t/s3c24x0/serial.c @@ -0,0 +1,182 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include +#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) + +#if defined(CONFIG_S3C2400) || defined(CONFIG_TRAB) +#include +#elif defined(CONFIG_S3C2410) +#include +#endif + +#ifdef CONFIG_SERIAL1 +#define UART_NR S3C24X0_UART0 + +#elif defined(CONFIG_SERIAL2) +# if defined(CONFIG_TRAB) +# error "TRAB supports only CONFIG_SERIAL1" +# endif +#define UART_NR S3C24X0_UART1 + +#elif defined(CONFIG_SERIAL3) +# if defined(CONFIG_TRAB) +# #error "TRAB supports only CONFIG_SERIAL1" +# endif +#define UART_NR S3C24X0_UART2 + +#else +#error "Bad: you didn't configure serial ..." +#endif + +void serial_setbrg (void) +{ + DECLARE_GLOBAL_DATA_PTR; + S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); + int i; + unsigned int reg = 0; + + /* value is calculated so : (int)(PCLK/16./baudrate) -1 */ + reg = get_PCLK() / (16 * gd->baudrate) - 1; + + /* FIFO enable, Tx/Rx FIFO clear */ + uart->UFCON = 0x07; + uart->UMCON = 0x0; + /* Normal,No parity,1 stop,8 bit */ + uart->ULCON = 0x3; + /* + * tx=level,rx=edge,disable timeout int.,enable rx error int., + * normal,interrupt or polling + */ + uart->UCON = 0x245; + uart->UBRDIV = reg; + +#ifdef CONFIG_HWFLOW + uart->UMCON = 0x1; /* RTS up */ +#endif + for (i = 0; i < 100; i++); +} + +/* + * Initialise the serial port with the given baudrate. The settings + * are always 8 data bits, no parity, 1 stop bit, no start bits. + * + */ +int serial_init (void) +{ + serial_setbrg (); + + return (0); +} + +/* + * Read a single byte from the serial port. Returns 1 on success, 0 + * otherwise. When the function is succesfull, the character read is + * written into its argument c. + */ +int serial_getc (void) +{ + S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); + + /* wait for character to arrive */ + while (!(uart->UTRSTAT & 0x1)); + + return uart->URXH & 0xff; +} + +#ifdef CONFIG_HWFLOW +static int hwflow = 0; /* turned off by default */ +int hwflow_onoff(int on) +{ + switch(on) { + case 0: + default: + break; /* return current */ + case 1: + hwflow = 1; /* turn on */ + break; + case -1: + hwflow = 0; /* turn off */ + break; + } + return hwflow; +} +#endif + +#ifdef CONFIG_MODEM_SUPPORT +static int be_quiet = 0; +void disable_putc(void) +{ + be_quiet = 1; +} + +void enable_putc(void) +{ + be_quiet = 0; +} +#endif + + +/* + * Output a single byte to the serial port. + */ +void serial_putc (const char c) +{ + S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); +#ifdef CONFIG_MODEM_SUPPORT + if (be_quiet) + return; +#endif + + /* wait for room in the tx FIFO */ + while (!(uart->UTRSTAT & 0x2)); + +#ifdef CONFIG_HWFLOW + /* Wait for CTS up */ + while(hwflow && !(uart->UMSTAT & 0x1)) + ; +#endif + + uart->UTXH = c; + + /* If \n, also do \r */ + if (c == '\n') + serial_putc ('\r'); +} + +/* + * Test whether a character is in the RX buffer + */ +int serial_tstc (void) +{ + S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); + + return uart->UTRSTAT & 0x1; +} + +void +serial_puts (const char *s) +{ + while (*s) { + serial_putc (*s++); + } +} + +#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/s3c24x0/speed.c b/cpu/arm920t/s3c24x0/speed.c new file mode 100644 index 0000000..e0dca62 --- /dev/null +++ b/cpu/arm920t/s3c24x0/speed.c @@ -0,0 +1,101 @@ +/* + * (C) Copyright 2001-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, d.mueller@elsoft.ch + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* This code should work for both the S3C2400 and the S3C2410 + * as they seem to have the same PLL and clock machinery inside. + * The different address mapping is handled by the s3c24xx.h files below. + */ + +#include +#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) + +#if defined(CONFIG_S3C2400) +#include +#elif defined(CONFIG_S3C2410) +#include +#endif + +#define MPLL 0 +#define UPLL 1 + +/* ------------------------------------------------------------------------- */ +/* NOTE: This describes the proper use of this file. + * + * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL. + * + * get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of + * the specified bus in HZ. + */ +/* ------------------------------------------------------------------------- */ + +static ulong get_PLLCLK(int pllreg) +{ + S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); + ulong r, m, p, s; + + if (pllreg == MPLL) + r = clk_power->MPLLCON; + else if (pllreg == UPLL) + r = clk_power->UPLLCON; + else + hang(); + + m = ((r & 0xFF000) >> 12) + 8; + p = ((r & 0x003F0) >> 4) + 2; + s = r & 0x3; + + return((CONFIG_SYS_CLK_FREQ * m) / (p << s)); +} + +/* return FCLK frequency */ +ulong get_FCLK(void) +{ + return(get_PLLCLK(MPLL)); +} + +/* return HCLK frequency */ +ulong get_HCLK(void) +{ + S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); + + return((clk_power->CLKDIVN & 0x2) ? get_FCLK()/2 : get_FCLK()); +} + +/* return PCLK frequency */ +ulong get_PCLK(void) +{ + S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); + + return((clk_power->CLKDIVN & 0x1) ? get_HCLK()/2 : get_HCLK()); +} + +/* return UCLK frequency */ +ulong get_UCLK(void) +{ + return(get_PLLCLK(UPLL)); +} + +#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/s3c24x0/usb_ohci.c b/cpu/arm920t/s3c24x0/usb_ohci.c new file mode 100644 index 0000000..6f4a9f7 --- /dev/null +++ b/cpu/arm920t/s3c24x0/usb_ohci.c @@ -0,0 +1,1630 @@ +/* + * URB OHCI HCD (Host Controller Driver) for USB on the S3C2400. + * + * (C) Copyright 2003 + * Gary Jennejohn, DENX Software Engineering + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * Note: Part of this code has been derived from linux + * + */ +/* + * IMPORTANT NOTES + * 1 - you MUST define LITTLEENDIAN in the configuration file for the + * board or this driver will NOT work! + * 2 - this driver is intended for use with USB Mass Storage Devices + * (BBB) ONLY. There is NO support for Interrupt or Isochronous pipes! + */ + +#include +/* #include no PCI on the S3C24X0 */ + +#ifdef CONFIG_USB_OHCI + +#if defined(CONFIG_S3C2400) +#include +#elif defined(CONFIG_S3C2410) +#include +#endif + +#include +#include +#include "usb_ohci.h" + +#define OHCI_USE_NPS /* force NoPowerSwitching mode */ +#undef OHCI_VERBOSE_DEBUG /* not always helpful */ + + +/* For initializing controller (mask in an HCFS mode too) */ +#define OHCI_CONTROL_INIT \ + (OHCI_CTRL_CBSR & 0x3) | OHCI_CTRL_IE | OHCI_CTRL_PLE + +#define readl(a) (*((vu_long *)(a))) +#define writel(a, b) (*((vu_long *)(b)) = ((vu_long)a)) + +#define min_t(type,x,y) ({ type __x = (x); type __y = (y); __x < __y ? __x: __y; }) + +#undef DEBUG +#ifdef DEBUG +#define dbg(format, arg...) printf("DEBUG: " format "\n", ## arg) +#else +#define dbg(format, arg...) do {} while(0) +#endif /* DEBUG */ +#define err(format, arg...) printf("ERROR: " format "\n", ## arg) +#undef SHOW_INFO +#ifdef SHOW_INFO +#define info(format, arg...) printf("INFO: " format "\n", ## arg) +#else +#define info(format, arg...) do {} while(0) +#endif + +#define m16_swap(x) swap_16(x) +#define m32_swap(x) swap_32(x) + +/* global ohci_t */ +static ohci_t gohci; +/* this must be aligned to a 256 byte boundary */ +struct ohci_hcca ghcca[1]; +/* a pointer to the aligned storage */ +struct ohci_hcca *phcca; +/* this allocates EDs for all possible endpoints */ +struct ohci_device ohci_dev; +/* urb_priv */ +urb_priv_t urb_priv; +/* RHSC flag */ +int got_rhsc; +/* device which was disconnected */ +struct usb_device *devgone; + +/*-------------------------------------------------------------------------*/ + +/* AMD-756 (D2 rev) reports corrupt register contents in some cases. + * The erratum (#4) description is incorrect. AMD's workaround waits + * till some bits (mostly reserved) are clear; ok for all revs. + */ +#define OHCI_QUIRK_AMD756 0xabcd +#define read_roothub(hc, register, mask) ({ \ + u32 temp = readl (&hc->regs->roothub.register); \ + if (hc->flags & OHCI_QUIRK_AMD756) \ + while (temp & mask) \ + temp = readl (&hc->regs->roothub.register); \ + temp; }) + +static u32 roothub_a (struct ohci *hc) + { return read_roothub (hc, a, 0xfc0fe000); } +static inline u32 roothub_b (struct ohci *hc) + { return readl (&hc->regs->roothub.b); } +static inline u32 roothub_status (struct ohci *hc) + { return readl (&hc->regs->roothub.status); } +static u32 roothub_portstatus (struct ohci *hc, int i) + { return read_roothub (hc, portstatus [i], 0xffe0fce0); } + + +/* forward declaration */ +static int hc_interrupt (void); +static void +td_submit_job (struct usb_device * dev, unsigned long pipe, void * buffer, + int transfer_len, struct devrequest * setup, urb_priv_t * urb, int interval); + +/*-------------------------------------------------------------------------* + * URB support functions + *-------------------------------------------------------------------------*/ + +/* free HCD-private data associated with this URB */ + +static void urb_free_priv (urb_priv_t * urb) +{ + int i; + int last; + struct td * td; + + last = urb->length - 1; + if (last >= 0) { + for (i = 0; i <= last; i++) { + td = urb->td[i]; + if (td) { + td->usb_dev = NULL; + urb->td[i] = NULL; + } + } + } +} + +/*-------------------------------------------------------------------------*/ + +#ifdef DEBUG +static int sohci_get_current_frame_number (struct usb_device * dev); + +/* debug| print the main components of an URB + * small: 0) header + data packets 1) just header */ + +static void pkt_print (struct usb_device * dev, unsigned long pipe, void * buffer, + int transfer_len, struct devrequest * setup, char * str, int small) +{ + urb_priv_t * purb = &urb_priv; + + dbg("%s URB:[%4x] dev:%2d,ep:%2d-%c,type:%s,len:%d/%d stat:%#lx", + str, + sohci_get_current_frame_number (dev), + usb_pipedevice (pipe), + usb_pipeendpoint (pipe), + usb_pipeout (pipe)? 'O': 'I', + usb_pipetype (pipe) < 2? (usb_pipeint (pipe)? "INTR": "ISOC"): + (usb_pipecontrol (pipe)? "CTRL": "BULK"), + purb->actual_length, + transfer_len, dev->status); +#ifdef OHCI_VERBOSE_DEBUG + if (!small) { + int i, len; + + if (usb_pipecontrol (pipe)) { + printf (__FILE__ ": cmd(8):"); + for (i = 0; i < 8 ; i++) + printf (" %02x", ((__u8 *) setup) [i]); + printf ("\n"); + } + if (transfer_len > 0 && buffer) { + printf (__FILE__ ": data(%d/%d):", + purb->actual_length, + transfer_len); + len = usb_pipeout (pipe)? + transfer_len: purb->actual_length; + for (i = 0; i < 16 && i < len; i++) + printf (" %02x", ((__u8 *) buffer) [i]); + printf ("%s\n", i < len? "...": ""); + } + } +#endif +} + +/* just for debugging; prints non-empty branches of the int ed tree inclusive iso eds*/ +void ep_print_int_eds (ohci_t *ohci, char * str) { + int i, j; + __u32 * ed_p; + for (i= 0; i < 32; i++) { + j = 5; + ed_p = &(ohci->hcca->int_table [i]); + if (*ed_p == 0) + continue; + printf (__FILE__ ": %s branch int %2d(%2x):", str, i, i); + while (*ed_p != 0 && j--) { + ed_t *ed = (ed_t *)m32_swap(ed_p); + printf (" ed: %4x;", ed->hwINFO); + ed_p = &ed->hwNextED; + } + printf ("\n"); + } +} + +static void ohci_dump_intr_mask (char *label, __u32 mask) +{ + dbg ("%s: 0x%08x%s%s%s%s%s%s%s%s%s", + label, + mask, + (mask & OHCI_INTR_MIE) ? " MIE" : "", + (mask & OHCI_INTR_OC) ? " OC" : "", + (mask & OHCI_INTR_RHSC) ? " RHSC" : "", + (mask & OHCI_INTR_FNO) ? " FNO" : "", + (mask & OHCI_INTR_UE) ? " UE" : "", + (mask & OHCI_INTR_RD) ? " RD" : "", + (mask & OHCI_INTR_SF) ? " SF" : "", + (mask & OHCI_INTR_WDH) ? " WDH" : "", + (mask & OHCI_INTR_SO) ? " SO" : "" + ); +} + +static void maybe_print_eds (char *label, __u32 value) +{ + ed_t *edp = (ed_t *)value; + + if (value) { + dbg ("%s %08x", label, value); + dbg ("%08x", edp->hwINFO); + dbg ("%08x", edp->hwTailP); + dbg ("%08x", edp->hwHeadP); + dbg ("%08x", edp->hwNextED); + } +} + +static char * hcfs2string (int state) +{ + switch (state) { + case OHCI_USB_RESET: return "reset"; + case OHCI_USB_RESUME: return "resume"; + case OHCI_USB_OPER: return "operational"; + case OHCI_USB_SUSPEND: return "suspend"; + } + return "?"; +} + +/* dump control and status registers */ +static void ohci_dump_status (ohci_t *controller) +{ + struct ohci_regs *regs = controller->regs; + __u32 temp; + + temp = readl (®s->revision) & 0xff; + if (temp != 0x10) + dbg ("spec %d.%d", (temp >> 4), (temp & 0x0f)); + + temp = readl (®s->control); + dbg ("control: 0x%08x%s%s%s HCFS=%s%s%s%s%s CBSR=%d", temp, + (temp & OHCI_CTRL_RWE) ? " RWE" : "", + (temp & OHCI_CTRL_RWC) ? " RWC" : "", + (temp & OHCI_CTRL_IR) ? " IR" : "", + hcfs2string (temp & OHCI_CTRL_HCFS), + (temp & OHCI_CTRL_BLE) ? " BLE" : "", + (temp & OHCI_CTRL_CLE) ? " CLE" : "", + (temp & OHCI_CTRL_IE) ? " IE" : "", + (temp & OHCI_CTRL_PLE) ? " PLE" : "", + temp & OHCI_CTRL_CBSR + ); + + temp = readl (®s->cmdstatus); + dbg ("cmdstatus: 0x%08x SOC=%d%s%s%s%s", temp, + (temp & OHCI_SOC) >> 16, + (temp & OHCI_OCR) ? " OCR" : "", + (temp & OHCI_BLF) ? " BLF" : "", + (temp & OHCI_CLF) ? " CLF" : "", + (temp & OHCI_HCR) ? " HCR" : "" + ); + + ohci_dump_intr_mask ("intrstatus", readl (®s->intrstatus)); + ohci_dump_intr_mask ("intrenable", readl (®s->intrenable)); + + maybe_print_eds ("ed_periodcurrent", readl (®s->ed_periodcurrent)); + + maybe_print_eds ("ed_controlhead", readl (®s->ed_controlhead)); + maybe_print_eds ("ed_controlcurrent", readl (®s->ed_controlcurrent)); + + maybe_print_eds ("ed_bulkhead", readl (®s->ed_bulkhead)); + maybe_print_eds ("ed_bulkcurrent", readl (®s->ed_bulkcurrent)); + + maybe_print_eds ("donehead", readl (®s->donehead)); +} + +static void ohci_dump_roothub (ohci_t *controller, int verbose) +{ + __u32 temp, ndp, i; + + temp = roothub_a (controller); + ndp = (temp & RH_A_NDP); + + if (verbose) { + dbg ("roothub.a: %08x POTPGT=%d%s%s%s%s%s NDP=%d", temp, + ((temp & RH_A_POTPGT) >> 24) & 0xff, + (temp & RH_A_NOCP) ? " NOCP" : "", + (temp & RH_A_OCPM) ? " OCPM" : "", + (temp & RH_A_DT) ? " DT" : "", + (temp & RH_A_NPS) ? " NPS" : "", + (temp & RH_A_PSM) ? " PSM" : "", + ndp + ); + temp = roothub_b (controller); + dbg ("roothub.b: %08x PPCM=%04x DR=%04x", + temp, + (temp & RH_B_PPCM) >> 16, + (temp & RH_B_DR) + ); + temp = roothub_status (controller); + dbg ("roothub.status: %08x%s%s%s%s%s%s", + temp, + (temp & RH_HS_CRWE) ? " CRWE" : "", + (temp & RH_HS_OCIC) ? " OCIC" : "", + (temp & RH_HS_LPSC) ? " LPSC" : "", + (temp & RH_HS_DRWE) ? " DRWE" : "", + (temp & RH_HS_OCI) ? " OCI" : "", + (temp & RH_HS_LPS) ? " LPS" : "" + ); + } + + for (i = 0; i < ndp; i++) { + temp = roothub_portstatus (controller, i); + dbg ("roothub.portstatus [%d] = 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s", + i, + temp, + (temp & RH_PS_PRSC) ? " PRSC" : "", + (temp & RH_PS_OCIC) ? " OCIC" : "", + (temp & RH_PS_PSSC) ? " PSSC" : "", + (temp & RH_PS_PESC) ? " PESC" : "", + (temp & RH_PS_CSC) ? " CSC" : "", + + (temp & RH_PS_LSDA) ? " LSDA" : "", + (temp & RH_PS_PPS) ? " PPS" : "", + (temp & RH_PS_PRS) ? " PRS" : "", + (temp & RH_PS_POCI) ? " POCI" : "", + (temp & RH_PS_PSS) ? " PSS" : "", + + (temp & RH_PS_PES) ? " PES" : "", + (temp & RH_PS_CCS) ? " CCS" : "" + ); + } +} + +static void ohci_dump (ohci_t *controller, int verbose) +{ + dbg ("OHCI controller usb-%s state", controller->slot_name); + + /* dumps some of the state we know about */ + ohci_dump_status (controller); + if (verbose) + ep_print_int_eds (controller, "hcca"); + dbg ("hcca frame #%04x", controller->hcca->frame_no); + ohci_dump_roothub (controller, 1); +} + + +#endif /* DEBUG */ + +/*-------------------------------------------------------------------------* + * Interface functions (URB) + *-------------------------------------------------------------------------*/ + +/* get a transfer request */ + +int sohci_submit_job(struct usb_device *dev, unsigned long pipe, void *buffer, + int transfer_len, struct devrequest *setup, int interval) +{ + ohci_t *ohci; + ed_t * ed; + urb_priv_t *purb_priv; + int i, size = 0; + + ohci = &gohci; + + /* when controller's hung, permit only roothub cleanup attempts + * such as powering down ports */ + if (ohci->disabled) { + err("sohci_submit_job: EPIPE"); + return -1; + } + + /* every endpoint has a ed, locate and fill it */ + if (!(ed = ep_add_ed (dev, pipe))) { + err("sohci_submit_job: ENOMEM"); + return -1; + } + + /* for the private part of the URB we need the number of TDs (size) */ + switch (usb_pipetype (pipe)) { + case PIPE_BULK: /* one TD for every 4096 Byte */ + size = (transfer_len - 1) / 4096 + 1; + break; + case PIPE_CONTROL: /* 1 TD for setup, 1 for ACK and 1 for every 4096 B */ + size = (transfer_len == 0)? 2: + (transfer_len - 1) / 4096 + 3; + break; + } + + if (size >= (N_URB_TD - 1)) { + err("need %d TDs, only have %d", size, N_URB_TD); + return -1; + } + purb_priv = &urb_priv; + purb_priv->pipe = pipe; + + /* fill the private part of the URB */ + purb_priv->length = size; + purb_priv->ed = ed; + purb_priv->actual_length = 0; + + /* allocate the TDs */ + /* note that td[0] was allocated in ep_add_ed */ + for (i = 0; i < size; i++) { + purb_priv->td[i] = td_alloc (dev); + if (!purb_priv->td[i]) { + purb_priv->length = i; + urb_free_priv (purb_priv); + err("sohci_submit_job: ENOMEM"); + return -1; + } + } + + if (ed->state == ED_NEW || (ed->state & ED_DEL)) { + urb_free_priv (purb_priv); + err("sohci_submit_job: EINVAL"); + return -1; + } + + /* link the ed into a chain if is not already */ + if (ed->state != ED_OPER) + ep_link (ohci, ed); + + /* fill the TDs and link it to the ed */ + td_submit_job(dev, pipe, buffer, transfer_len, setup, purb_priv, interval); + + return 0; +} + +/*-------------------------------------------------------------------------*/ + +#ifdef DEBUG +/* tell us the current USB frame number */ + +static int sohci_get_current_frame_number (struct usb_device *usb_dev) +{ + ohci_t *ohci = &gohci; + + return m16_swap (ohci->hcca->frame_no); +} +#endif + +/*-------------------------------------------------------------------------* + * ED handling functions + *-------------------------------------------------------------------------*/ + +/* link an ed into one of the HC chains */ + +static int ep_link (ohci_t *ohci, ed_t *edi) +{ + volatile ed_t *ed = edi; + + ed->state = ED_OPER; + + switch (ed->type) { + case PIPE_CONTROL: + ed->hwNextED = 0; + if (ohci->ed_controltail == NULL) { + writel (ed, &ohci->regs->ed_controlhead); + } else { + ohci->ed_controltail->hwNextED = m32_swap (ed); + } + ed->ed_prev = ohci->ed_controltail; + if (!ohci->ed_controltail && !ohci->ed_rm_list[0] && + !ohci->ed_rm_list[1] && !ohci->sleeping) { + ohci->hc_control |= OHCI_CTRL_CLE; + writel (ohci->hc_control, &ohci->regs->control); + } + ohci->ed_controltail = edi; + break; + + case PIPE_BULK: + ed->hwNextED = 0; + if (ohci->ed_bulktail == NULL) { + writel (ed, &ohci->regs->ed_bulkhead); + } else { + ohci->ed_bulktail->hwNextED = m32_swap (ed); + } + ed->ed_prev = ohci->ed_bulktail; + if (!ohci->ed_bulktail && !ohci->ed_rm_list[0] && + !ohci->ed_rm_list[1] && !ohci->sleeping) { + ohci->hc_control |= OHCI_CTRL_BLE; + writel (ohci->hc_control, &ohci->regs->control); + } + ohci->ed_bulktail = edi; + break; + } + return 0; +} + +/*-------------------------------------------------------------------------*/ + +/* unlink an ed from one of the HC chains. + * just the link to the ed is unlinked. + * the link from the ed still points to another operational ed or 0 + * so the HC can eventually finish the processing of the unlinked ed */ + +static int ep_unlink (ohci_t *ohci, ed_t *ed) +{ + ed->hwINFO |= m32_swap (OHCI_ED_SKIP); + + switch (ed->type) { + case PIPE_CONTROL: + if (ed->ed_prev == NULL) { + if (!ed->hwNextED) { + ohci->hc_control &= ~OHCI_CTRL_CLE; + writel (ohci->hc_control, &ohci->regs->control); + } + writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_controlhead); + } else { + ed->ed_prev->hwNextED = ed->hwNextED; + } + if (ohci->ed_controltail == ed) { + ohci->ed_controltail = ed->ed_prev; + } else { + ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev; + } + break; + + case PIPE_BULK: + if (ed->ed_prev == NULL) { + if (!ed->hwNextED) { + ohci->hc_control &= ~OHCI_CTRL_BLE; + writel (ohci->hc_control, &ohci->regs->control); + } + writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_bulkhead); + } else { + ed->ed_prev->hwNextED = ed->hwNextED; + } + if (ohci->ed_bulktail == ed) { + ohci->ed_bulktail = ed->ed_prev; + } else { + ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev; + } + break; + } + ed->state = ED_UNLINK; + return 0; +} + + +/*-------------------------------------------------------------------------*/ + +/* add/reinit an endpoint; this should be done once at the usb_set_configuration command, + * but the USB stack is a little bit stateless so we do it at every transaction + * if the state of the ed is ED_NEW then a dummy td is added and the state is changed to ED_UNLINK + * in all other cases the state is left unchanged + * the ed info fields are setted anyway even though most of them should not change */ + +static ed_t * ep_add_ed (struct usb_device *usb_dev, unsigned long pipe) +{ + td_t *td; + ed_t *ed_ret; + volatile ed_t *ed; + + ed = ed_ret = &ohci_dev.ed[(usb_pipeendpoint (pipe) << 1) | + (usb_pipecontrol (pipe)? 0: usb_pipeout (pipe))]; + + if ((ed->state & ED_DEL) || (ed->state & ED_URB_DEL)) { + err("ep_add_ed: pending delete"); + /* pending delete request */ + return NULL; + } + + if (ed->state == ED_NEW) { + ed->hwINFO = m32_swap (OHCI_ED_SKIP); /* skip ed */ + /* dummy td; end of td list for ed */ + td = td_alloc (usb_dev); + ed->hwTailP = m32_swap (td); + ed->hwHeadP = ed->hwTailP; + ed->state = ED_UNLINK; + ed->type = usb_pipetype (pipe); + ohci_dev.ed_cnt++; + } + + ed->hwINFO = m32_swap (usb_pipedevice (pipe) + | usb_pipeendpoint (pipe) << 7 + | (usb_pipeisoc (pipe)? 0x8000: 0) + | (usb_pipecontrol (pipe)? 0: (usb_pipeout (pipe)? 0x800: 0x1000)) + | usb_pipeslow (pipe) << 13 + | usb_maxpacket (usb_dev, pipe) << 16); + + return ed_ret; +} + +/*-------------------------------------------------------------------------* + * TD handling functions + *-------------------------------------------------------------------------*/ + +/* enqueue next TD for this URB (OHCI spec 5.2.8.2) */ + +static void td_fill (ohci_t *ohci, unsigned int info, + void *data, int len, + struct usb_device *dev, int index, urb_priv_t *urb_priv) +{ + volatile td_t *td, *td_pt; +#ifdef OHCI_FILL_TRACE + int i; +#endif + + if (index > urb_priv->length) { + err("index > length"); + return; + } + /* use this td as the next dummy */ + td_pt = urb_priv->td [index]; + td_pt->hwNextTD = 0; + + /* fill the old dummy TD */ + td = urb_priv->td [index] = (td_t *)(m32_swap (urb_priv->ed->hwTailP) & ~0xf); + + td->ed = urb_priv->ed; + td->next_dl_td = NULL; + td->index = index; + td->data = (__u32)data; +#ifdef OHCI_FILL_TRACE + if ((usb_pipetype(urb_priv->pipe) == PIPE_BULK) && usb_pipeout(urb_priv->pipe)) { + for (i = 0; i < len; i++) + printf("td->data[%d] %#2x ",i, ((unsigned char *)td->data)[i]); + printf("\n"); + } +#endif + if (!len) + data = 0; + + td->hwINFO = m32_swap (info); + td->hwCBP = m32_swap (data); + if (data) + td->hwBE = m32_swap (data + len - 1); + else + td->hwBE = 0; + td->hwNextTD = m32_swap (td_pt); + td->hwPSW [0] = m16_swap (((__u32)data & 0x0FFF) | 0xE000); + + /* append to queue */ + td->ed->hwTailP = td->hwNextTD; +} + +/*-------------------------------------------------------------------------*/ + +/* prepare all TDs of a transfer */ + +static void td_submit_job (struct usb_device *dev, unsigned long pipe, void *buffer, + int transfer_len, struct devrequest *setup, urb_priv_t *urb, int interval) +{ + ohci_t *ohci = &gohci; + int data_len = transfer_len; + void *data; + int cnt = 0; + __u32 info = 0; + unsigned int toggle = 0; + + /* OHCI handles the DATA-toggles itself, we just use the USB-toggle bits for reseting */ + if(usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe))) { + toggle = TD_T_TOGGLE; + } else { + toggle = TD_T_DATA0; + usb_settoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe), 1); + } + urb->td_cnt = 0; + if (data_len) + data = buffer; + else + data = 0; + + switch (usb_pipetype (pipe)) { + case PIPE_BULK: + info = usb_pipeout (pipe)? + TD_CC | TD_DP_OUT : TD_CC | TD_DP_IN ; + while(data_len > 4096) { + td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, 4096, dev, cnt, urb); + data += 4096; data_len -= 4096; cnt++; + } + info = usb_pipeout (pipe)? + TD_CC | TD_DP_OUT : TD_CC | TD_R | TD_DP_IN ; + td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, data_len, dev, cnt, urb); + cnt++; + + if (!ohci->sleeping) + writel (OHCI_BLF, &ohci->regs->cmdstatus); /* start bulk list */ + break; + + case PIPE_CONTROL: + info = TD_CC | TD_DP_SETUP | TD_T_DATA0; + td_fill (ohci, info, setup, 8, dev, cnt++, urb); + if (data_len > 0) { + info = usb_pipeout (pipe)? + TD_CC | TD_R | TD_DP_OUT | TD_T_DATA1 : TD_CC | TD_R | TD_DP_IN | TD_T_DATA1; + /* NOTE: mishandles transfers >8K, some >4K */ + td_fill (ohci, info, data, data_len, dev, cnt++, urb); + } + info = usb_pipeout (pipe)? + TD_CC | TD_DP_IN | TD_T_DATA1: TD_CC | TD_DP_OUT | TD_T_DATA1; + td_fill (ohci, info, data, 0, dev, cnt++, urb); + if (!ohci->sleeping) + writel (OHCI_CLF, &ohci->regs->cmdstatus); /* start Control list */ + break; + } + if (urb->length != cnt) + dbg("TD LENGTH %d != CNT %d", urb->length, cnt); +} + +/*-------------------------------------------------------------------------* + * Done List handling functions + *-------------------------------------------------------------------------*/ + + +/* calculate the transfer length and update the urb */ + +static void dl_transfer_length(td_t * td) +{ + __u32 tdINFO, tdBE, tdCBP; + urb_priv_t *lurb_priv = &urb_priv; + + tdINFO = m32_swap (td->hwINFO); + tdBE = m32_swap (td->hwBE); + tdCBP = m32_swap (td->hwCBP); + + + if (!(usb_pipetype (lurb_priv->pipe) == PIPE_CONTROL && + ((td->index == 0) || (td->index == lurb_priv->length - 1)))) { + if (tdBE != 0) { + if (td->hwCBP == 0) + lurb_priv->actual_length += tdBE - td->data + 1; + else + lurb_priv->actual_length += tdCBP - td->data; + } + } +} + +/*-------------------------------------------------------------------------*/ + +/* replies to the request have to be on a FIFO basis so + * we reverse the reversed done-list */ + +static td_t * dl_reverse_done_list (ohci_t *ohci) +{ + __u32 td_list_hc; + td_t *td_rev = NULL; + td_t *td_list = NULL; + urb_priv_t *lurb_priv = NULL; + + td_list_hc = m32_swap (ohci->hcca->done_head) & 0xfffffff0; + ohci->hcca->done_head = 0; + + while (td_list_hc) { + td_list = (td_t *)td_list_hc; + + if (TD_CC_GET (m32_swap (td_list->hwINFO))) { + lurb_priv = &urb_priv; + dbg(" USB-error/status: %x : %p", + TD_CC_GET (m32_swap (td_list->hwINFO)), td_list); + if (td_list->ed->hwHeadP & m32_swap (0x1)) { + if (lurb_priv && ((td_list->index + 1) < lurb_priv->length)) { + td_list->ed->hwHeadP = + (lurb_priv->td[lurb_priv->length - 1]->hwNextTD & m32_swap (0xfffffff0)) | + (td_list->ed->hwHeadP & m32_swap (0x2)); + lurb_priv->td_cnt += lurb_priv->length - td_list->index - 1; + } else + td_list->ed->hwHeadP &= m32_swap (0xfffffff2); + } + } + + td_list->next_dl_td = td_rev; + td_rev = td_list; + td_list_hc = m32_swap (td_list->hwNextTD) & 0xfffffff0; + } + return td_list; +} + +/*-------------------------------------------------------------------------*/ + +/* td done list */ +static int dl_done_list (ohci_t *ohci, td_t *td_list) +{ + td_t *td_list_next = NULL; + ed_t *ed; + int cc = 0; + int stat = 0; + /* urb_t *urb; */ + urb_priv_t *lurb_priv; + __u32 tdINFO, edHeadP, edTailP; + + while (td_list) { + td_list_next = td_list->next_dl_td; + + lurb_priv = &urb_priv; + tdINFO = m32_swap (td_list->hwINFO); + + ed = td_list->ed; + + dl_transfer_length(td_list); + + /* error code of transfer */ + cc = TD_CC_GET (tdINFO); + if (cc != 0) { + dbg("ConditionCode %#x", cc); + stat = cc_to_error[cc]; + } + + if (ed->state != ED_NEW) { + edHeadP = m32_swap (ed->hwHeadP) & 0xfffffff0; + edTailP = m32_swap (ed->hwTailP); + + /* unlink eds if they are not busy */ + if ((edHeadP == edTailP) && (ed->state == ED_OPER)) + ep_unlink (ohci, ed); + } + + td_list = td_list_next; + } + return stat; +} + +/*-------------------------------------------------------------------------* + * Virtual Root Hub + *-------------------------------------------------------------------------*/ + +/* Device descriptor */ +static __u8 root_hub_dev_des[] = +{ + 0x12, /* __u8 bLength; */ + 0x01, /* __u8 bDescriptorType; Device */ + 0x10, /* __u16 bcdUSB; v1.1 */ + 0x01, + 0x09, /* __u8 bDeviceClass; HUB_CLASSCODE */ + 0x00, /* __u8 bDeviceSubClass; */ + 0x00, /* __u8 bDeviceProtocol; */ + 0x08, /* __u8 bMaxPacketSize0; 8 Bytes */ + 0x00, /* __u16 idVendor; */ + 0x00, + 0x00, /* __u16 idProduct; */ + 0x00, + 0x00, /* __u16 bcdDevice; */ + 0x00, + 0x00, /* __u8 iManufacturer; */ + 0x01, /* __u8 iProduct; */ + 0x00, /* __u8 iSerialNumber; */ + 0x01 /* __u8 bNumConfigurations; */ +}; + + +/* Configuration descriptor */ +static __u8 root_hub_config_des[] = +{ + 0x09, /* __u8 bLength; */ + 0x02, /* __u8 bDescriptorType; Configuration */ + 0x19, /* __u16 wTotalLength; */ + 0x00, + 0x01, /* __u8 bNumInterfaces; */ + 0x01, /* __u8 bConfigurationValue; */ + 0x00, /* __u8 iConfiguration; */ + 0x40, /* __u8 bmAttributes; + Bit 7: Bus-powered, 6: Self-powered, 5 Remote-wakwup, 4..0: resvd */ + 0x00, /* __u8 MaxPower; */ + + /* interface */ + 0x09, /* __u8 if_bLength; */ + 0x04, /* __u8 if_bDescriptorType; Interface */ + 0x00, /* __u8 if_bInterfaceNumber; */ + 0x00, /* __u8 if_bAlternateSetting; */ + 0x01, /* __u8 if_bNumEndpoints; */ + 0x09, /* __u8 if_bInterfaceClass; HUB_CLASSCODE */ + 0x00, /* __u8 if_bInterfaceSubClass; */ + 0x00, /* __u8 if_bInterfaceProtocol; */ + 0x00, /* __u8 if_iInterface; */ + + /* endpoint */ + 0x07, /* __u8 ep_bLength; */ + 0x05, /* __u8 ep_bDescriptorType; Endpoint */ + 0x81, /* __u8 ep_bEndpointAddress; IN Endpoint 1 */ + 0x03, /* __u8 ep_bmAttributes; Interrupt */ + 0x02, /* __u16 ep_wMaxPacketSize; ((MAX_ROOT_PORTS + 1) / 8 */ + 0x00, + 0xff /* __u8 ep_bInterval; 255 ms */ +}; + +static unsigned char root_hub_str_index0[] = +{ + 0x04, /* __u8 bLength; */ + 0x03, /* __u8 bDescriptorType; String-descriptor */ + 0x09, /* __u8 lang ID */ + 0x04, /* __u8 lang ID */ +}; + +static unsigned char root_hub_str_index1[] = +{ + 28, /* __u8 bLength; */ + 0x03, /* __u8 bDescriptorType; String-descriptor */ + 'O', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'H', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'C', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'I', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + ' ', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'R', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'o', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'o', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 't', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + ' ', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'H', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'u', /* __u8 Unicode */ + 0, /* __u8 Unicode */ + 'b', /* __u8 Unicode */ + 0, /* __u8 Unicode */ +}; + +/* Hub class-specific descriptor is constructed dynamically */ + + +/*-------------------------------------------------------------------------*/ + +#define OK(x) len = (x); break +#ifdef DEBUG +#define WR_RH_STAT(x) {info("WR:status %#8x", (x));writel((x), &gohci.regs->roothub.status);} +#define WR_RH_PORTSTAT(x) {info("WR:portstatus[%d] %#8x", wIndex-1, (x));writel((x), &gohci.regs->roothub.portstatus[wIndex-1]);} +#else +#define WR_RH_STAT(x) writel((x), &gohci.regs->roothub.status) +#define WR_RH_PORTSTAT(x) writel((x), &gohci.regs->roothub.portstatus[wIndex-1]) +#endif +#define RD_RH_STAT roothub_status(&gohci) +#define RD_RH_PORTSTAT roothub_portstatus(&gohci,wIndex-1) + +/* request to virtual root hub */ + +int rh_check_port_status(ohci_t *controller) +{ + __u32 temp, ndp, i; + int res; + + res = -1; + temp = roothub_a (controller); + ndp = (temp & RH_A_NDP); + for (i = 0; i < ndp; i++) { + temp = roothub_portstatus (controller, i); + /* check for a device disconnect */ + if (((temp & (RH_PS_PESC | RH_PS_CSC)) == + (RH_PS_PESC | RH_PS_CSC)) && + ((temp & RH_PS_CCS) == 0)) { + res = i; + break; + } + } + return res; +} + +static int ohci_submit_rh_msg(struct usb_device *dev, unsigned long pipe, + void *buffer, int transfer_len, struct devrequest *cmd) +{ + void * data = buffer; + int leni = transfer_len; + int len = 0; + int stat = 0; + __u32 datab[4]; + __u8 *data_buf = (__u8 *)datab; + __u16 bmRType_bReq; + __u16 wValue; + __u16 wIndex; + __u16 wLength; + +#ifdef DEBUG +urb_priv.actual_length = 0; +pkt_print(dev, pipe, buffer, transfer_len, cmd, "SUB(rh)", usb_pipein(pipe)); +#else + wait_ms(1); +#endif + if ((pipe & PIPE_INTERRUPT) == PIPE_INTERRUPT) { + info("Root-Hub submit IRQ: NOT implemented"); + return 0; + } + + bmRType_bReq = cmd->requesttype | (cmd->request << 8); + wValue = m16_swap (cmd->value); + wIndex = m16_swap (cmd->index); + wLength = m16_swap (cmd->length); + + info("Root-Hub: adr: %2x cmd(%1x): %08x %04x %04x %04x", + dev->devnum, 8, bmRType_bReq, wValue, wIndex, wLength); + + switch (bmRType_bReq) { + /* Request Destination: + without flags: Device, + RH_INTERFACE: interface, + RH_ENDPOINT: endpoint, + RH_CLASS means HUB here, + RH_OTHER | RH_CLASS almost ever means HUB_PORT here + */ + + case RH_GET_STATUS: + *(__u16 *) data_buf = m16_swap (1); OK (2); + case RH_GET_STATUS | RH_INTERFACE: + *(__u16 *) data_buf = m16_swap (0); OK (2); + case RH_GET_STATUS | RH_ENDPOINT: + *(__u16 *) data_buf = m16_swap (0); OK (2); + case RH_GET_STATUS | RH_CLASS: + *(__u32 *) data_buf = m32_swap ( + RD_RH_STAT & ~(RH_HS_CRWE | RH_HS_DRWE)); + OK (4); + case RH_GET_STATUS | RH_OTHER | RH_CLASS: + *(__u32 *) data_buf = m32_swap (RD_RH_PORTSTAT); OK (4); + + case RH_CLEAR_FEATURE | RH_ENDPOINT: + switch (wValue) { + case (RH_ENDPOINT_STALL): OK (0); + } + break; + + case RH_CLEAR_FEATURE | RH_CLASS: + switch (wValue) { + case RH_C_HUB_LOCAL_POWER: + OK(0); + case (RH_C_HUB_OVER_CURRENT): + WR_RH_STAT(RH_HS_OCIC); OK (0); + } + break; + + case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS: + switch (wValue) { + case (RH_PORT_ENABLE): + WR_RH_PORTSTAT (RH_PS_CCS ); OK (0); + case (RH_PORT_SUSPEND): + WR_RH_PORTSTAT (RH_PS_POCI); OK (0); + case (RH_PORT_POWER): + WR_RH_PORTSTAT (RH_PS_LSDA); OK (0); + case (RH_C_PORT_CONNECTION): + WR_RH_PORTSTAT (RH_PS_CSC ); OK (0); + case (RH_C_PORT_ENABLE): + WR_RH_PORTSTAT (RH_PS_PESC); OK (0); + case (RH_C_PORT_SUSPEND): + WR_RH_PORTSTAT (RH_PS_PSSC); OK (0); + case (RH_C_PORT_OVER_CURRENT): + WR_RH_PORTSTAT (RH_PS_OCIC); OK (0); + case (RH_C_PORT_RESET): + WR_RH_PORTSTAT (RH_PS_PRSC); OK (0); + } + break; + + case RH_SET_FEATURE | RH_OTHER | RH_CLASS: + switch (wValue) { + case (RH_PORT_SUSPEND): + WR_RH_PORTSTAT (RH_PS_PSS ); OK (0); + case (RH_PORT_RESET): /* BUG IN HUP CODE *********/ + if (RD_RH_PORTSTAT & RH_PS_CCS) + WR_RH_PORTSTAT (RH_PS_PRS); + OK (0); + case (RH_PORT_POWER): + WR_RH_PORTSTAT (RH_PS_PPS ); OK (0); + case (RH_PORT_ENABLE): /* BUG IN HUP CODE *********/ + if (RD_RH_PORTSTAT & RH_PS_CCS) + WR_RH_PORTSTAT (RH_PS_PES ); + OK (0); + } + break; + + case RH_SET_ADDRESS: gohci.rh.devnum = wValue; OK(0); + + case RH_GET_DESCRIPTOR: + switch ((wValue & 0xff00) >> 8) { + case (0x01): /* device descriptor */ + len = min_t(unsigned int, + leni, + min_t(unsigned int, + sizeof (root_hub_dev_des), + wLength)); + data_buf = root_hub_dev_des; OK(len); + case (0x02): /* configuration descriptor */ + len = min_t(unsigned int, + leni, + min_t(unsigned int, + sizeof (root_hub_config_des), + wLength)); + data_buf = root_hub_config_des; OK(len); + case (0x03): /* string descriptors */ + if(wValue==0x0300) { + len = min_t(unsigned int, + leni, + min_t(unsigned int, + sizeof (root_hub_str_index0), + wLength)); + data_buf = root_hub_str_index0; + OK(len); + } + if(wValue==0x0301) { + len = min_t(unsigned int, + leni, + min_t(unsigned int, + sizeof (root_hub_str_index1), + wLength)); + data_buf = root_hub_str_index1; + OK(len); + } + default: + stat = USB_ST_STALLED; + } + break; + + case RH_GET_DESCRIPTOR | RH_CLASS: + { + __u32 temp = roothub_a (&gohci); + + data_buf [0] = 9; /* min length; */ + data_buf [1] = 0x29; + data_buf [2] = temp & RH_A_NDP; + data_buf [3] = 0; + if (temp & RH_A_PSM) /* per-port power switching? */ + data_buf [3] |= 0x1; + if (temp & RH_A_NOCP) /* no overcurrent reporting? */ + data_buf [3] |= 0x10; + else if (temp & RH_A_OCPM) /* per-port overcurrent reporting? */ + data_buf [3] |= 0x8; + + /* corresponds to data_buf[4-7] */ + datab [1] = 0; + data_buf [5] = (temp & RH_A_POTPGT) >> 24; + temp = roothub_b (&gohci); + data_buf [7] = temp & RH_B_DR; + if (data_buf [2] < 7) { + data_buf [8] = 0xff; + } else { + data_buf [0] += 2; + data_buf [8] = (temp & RH_B_DR) >> 8; + data_buf [10] = data_buf [9] = 0xff; + } + + len = min_t(unsigned int, leni, + min_t(unsigned int, data_buf [0], wLength)); + OK (len); + } + + case RH_GET_CONFIGURATION: *(__u8 *) data_buf = 0x01; OK (1); + + case RH_SET_CONFIGURATION: WR_RH_STAT (0x10000); OK (0); + + default: + dbg ("unsupported root hub command"); + stat = USB_ST_STALLED; + } + +#ifdef DEBUG + ohci_dump_roothub (&gohci, 1); +#else + wait_ms(1); +#endif + + len = min_t(int, len, leni); + if (data != data_buf) + memcpy (data, data_buf, len); + dev->act_len = len; + dev->status = stat; + +#ifdef DEBUG + if (transfer_len) + urb_priv.actual_length = transfer_len; + pkt_print(dev, pipe, buffer, transfer_len, cmd, "RET(rh)", 0/*usb_pipein(pipe)*/); +#else + wait_ms(1); +#endif + + return stat; +} + +/*-------------------------------------------------------------------------*/ + +/* common code for handling submit messages - used for all but root hub */ +/* accesses. */ +int submit_common_msg(struct usb_device *dev, unsigned long pipe, void *buffer, + int transfer_len, struct devrequest *setup, int interval) +{ + int stat = 0; + int maxsize = usb_maxpacket(dev, pipe); + int timeout; + + /* device pulled? Shortcut the action. */ + if (devgone == dev) { + dev->status = USB_ST_CRC_ERR; + return 0; + } + +#ifdef DEBUG + urb_priv.actual_length = 0; + pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe)); +#else + wait_ms(1); +#endif + if (!maxsize) { + err("submit_common_message: pipesize for pipe %lx is zero", + pipe); + return -1; + } + + if (sohci_submit_job(dev, pipe, buffer, transfer_len, setup, interval) < 0) { + err("sohci_submit_job failed"); + return -1; + } + + wait_ms(10); + /* ohci_dump_status(&gohci); */ + + /* allow more time for a BULK device to react - some are slow */ +#define BULK_TO 5000 /* timeout in milliseconds */ + if (usb_pipetype (pipe) == PIPE_BULK) + timeout = BULK_TO; + else + timeout = 100; + + /* wait for it to complete */ + for (;;) { + /* check whether the controller is done */ + stat = hc_interrupt(); + if (stat < 0) { + stat = USB_ST_CRC_ERR; + break; + } + if (stat >= 0 && stat != 0xff) { + /* 0xff is returned for an SF-interrupt */ + break; + } + if (--timeout) { + wait_ms(1); + } else { + err("CTL:TIMEOUT "); + stat = USB_ST_CRC_ERR; + break; + } + } + /* we got an Root Hub Status Change interrupt */ + if (got_rhsc) { +#ifdef DEBUG + ohci_dump_roothub (&gohci, 1); +#endif + got_rhsc = 0; + /* abuse timeout */ + timeout = rh_check_port_status(&gohci); + if (timeout >= 0) { +#if 0 /* this does nothing useful, but leave it here in case that changes */ + /* the called routine adds 1 to the passed value */ + usb_hub_port_connect_change(gohci.rh.dev, timeout - 1); +#endif + /* + * XXX + * This is potentially dangerous because it assumes + * that only one device is ever plugged in! + */ + devgone = dev; + } + } + + dev->status = stat; + dev->act_len = transfer_len; + +#ifdef DEBUG + pkt_print(dev, pipe, buffer, transfer_len, setup, "RET(ctlr)", usb_pipein(pipe)); +#else + wait_ms(1); +#endif + + /* free TDs in urb_priv */ + urb_free_priv (&urb_priv); + return 0; +} + +/* submit routines called from usb.c */ +int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer, + int transfer_len) +{ + info("submit_bulk_msg"); + return submit_common_msg(dev, pipe, buffer, transfer_len, NULL, 0); +} + +int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, + int transfer_len, struct devrequest *setup) +{ + int maxsize = usb_maxpacket(dev, pipe); + + info("submit_control_msg"); +#ifdef DEBUG + urb_priv.actual_length = 0; + pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe)); +#else + wait_ms(1); +#endif + if (!maxsize) { + err("submit_control_message: pipesize for pipe %lx is zero", + pipe); + return -1; + } + if (((pipe >> 8) & 0x7f) == gohci.rh.devnum) { + gohci.rh.dev = dev; + /* root hub - redirect */ + return ohci_submit_rh_msg(dev, pipe, buffer, transfer_len, + setup); + } + + return submit_common_msg(dev, pipe, buffer, transfer_len, setup, 0); +} + +int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer, + int transfer_len, int interval) +{ + info("submit_int_msg"); + return -1; +} + +/*-------------------------------------------------------------------------* + * HC functions + *-------------------------------------------------------------------------*/ + +/* reset the HC and BUS */ + +static int hc_reset (ohci_t *ohci) +{ + int timeout = 30; + int smm_timeout = 50; /* 0,5 sec */ + + if (readl (&ohci->regs->control) & OHCI_CTRL_IR) { /* SMM owns the HC */ + writel (OHCI_OCR, &ohci->regs->cmdstatus); /* request ownership */ + info("USB HC TakeOver from SMM"); + while (readl (&ohci->regs->control) & OHCI_CTRL_IR) { + wait_ms (10); + if (--smm_timeout == 0) { + err("USB HC TakeOver failed!"); + return -1; + } + } + } + + /* Disable HC interrupts */ + writel (OHCI_INTR_MIE, &ohci->regs->intrdisable); + + dbg("USB HC reset_hc usb-%s: ctrl = 0x%X ;", + ohci->slot_name, + readl (&ohci->regs->control)); + + /* Reset USB (needed by some controllers) */ + writel (0, &ohci->regs->control); + + /* HC Reset requires max 10 us delay */ + writel (OHCI_HCR, &ohci->regs->cmdstatus); + while ((readl (&ohci->regs->cmdstatus) & OHCI_HCR) != 0) { + if (--timeout == 0) { + err("USB HC reset timed out!"); + return -1; + } + udelay (1); + } + return 0; +} + +/*-------------------------------------------------------------------------*/ + +/* Start an OHCI controller, set the BUS operational + * enable interrupts + * connect the virtual root hub */ + +static int hc_start (ohci_t * ohci) +{ + __u32 mask; + unsigned int fminterval; + + ohci->disabled = 1; + + /* Tell the controller where the control and bulk lists are + * The lists are empty now. */ + + writel (0, &ohci->regs->ed_controlhead); + writel (0, &ohci->regs->ed_bulkhead); + + writel ((__u32)ohci->hcca, &ohci->regs->hcca); /* a reset clears this */ + + fminterval = 0x2edf; + writel ((fminterval * 9) / 10, &ohci->regs->periodicstart); + fminterval |= ((((fminterval - 210) * 6) / 7) << 16); + writel (fminterval, &ohci->regs->fminterval); + writel (0x628, &ohci->regs->lsthresh); + + /* start controller operations */ + ohci->hc_control = OHCI_CONTROL_INIT | OHCI_USB_OPER; + ohci->disabled = 0; + writel (ohci->hc_control, &ohci->regs->control); + + /* disable all interrupts */ + mask = (OHCI_INTR_SO | OHCI_INTR_WDH | OHCI_INTR_SF | OHCI_INTR_RD | + OHCI_INTR_UE | OHCI_INTR_FNO | OHCI_INTR_RHSC | + OHCI_INTR_OC | OHCI_INTR_MIE); + writel (mask, &ohci->regs->intrdisable); + /* clear all interrupts */ + mask &= ~OHCI_INTR_MIE; + writel (mask, &ohci->regs->intrstatus); + /* Choose the interrupts we care about now - but w/o MIE */ + mask = OHCI_INTR_RHSC | OHCI_INTR_UE | OHCI_INTR_WDH | OHCI_INTR_SO; + writel (mask, &ohci->regs->intrenable); + +#ifdef OHCI_USE_NPS + /* required for AMD-756 and some Mac platforms */ + writel ((roothub_a (ohci) | RH_A_NPS) & ~RH_A_PSM, + &ohci->regs->roothub.a); + writel (RH_HS_LPSC, &ohci->regs->roothub.status); +#endif /* OHCI_USE_NPS */ + +#define mdelay(n) ({unsigned long msec=(n); while (msec--) udelay(1000);}) + /* POTPGT delay is bits 24-31, in 2 ms units. */ + mdelay ((roothub_a (ohci) >> 23) & 0x1fe); + + /* connect the virtual root hub */ + ohci->rh.devnum = 0; + + return 0; +} + +/*-------------------------------------------------------------------------*/ + +/* an interrupt happens */ + +static int +hc_interrupt (void) +{ + ohci_t *ohci = &gohci; + struct ohci_regs *regs = ohci->regs; + int ints; + int stat = -1; + + if ((ohci->hcca->done_head != 0) && !(m32_swap (ohci->hcca->done_head) & 0x01)) { + ints = OHCI_INTR_WDH; + } else { + ints = readl (®s->intrstatus); + } + + /* dbg("Interrupt: %x frame: %x", ints, le16_to_cpu (ohci->hcca->frame_no)); */ + + if (ints & OHCI_INTR_RHSC) { + got_rhsc = 1; + } + + if (ints & OHCI_INTR_UE) { + ohci->disabled++; + err ("OHCI Unrecoverable Error, controller usb-%s disabled", + ohci->slot_name); + /* e.g. due to PCI Master/Target Abort */ + +#ifdef DEBUG + ohci_dump (ohci, 1); +#else + wait_ms(1); +#endif + /* FIXME: be optimistic, hope that bug won't repeat often. */ + /* Make some non-interrupt context restart the controller. */ + /* Count and limit the retries though; either hardware or */ + /* software errors can go forever... */ + hc_reset (ohci); + return -1; + } + + if (ints & OHCI_INTR_WDH) { + wait_ms(1); + writel (OHCI_INTR_WDH, ®s->intrdisable); + stat = dl_done_list (&gohci, dl_reverse_done_list (&gohci)); + writel (OHCI_INTR_WDH, ®s->intrenable); + } + + if (ints & OHCI_INTR_SO) { + dbg("USB Schedule overrun\n"); + writel (OHCI_INTR_SO, ®s->intrenable); + stat = -1; + } + + /* FIXME: this assumes SOF (1/ms) interrupts don't get lost... */ + if (ints & OHCI_INTR_SF) { + unsigned int frame = m16_swap (ohci->hcca->frame_no) & 1; + wait_ms(1); + writel (OHCI_INTR_SF, ®s->intrdisable); + if (ohci->ed_rm_list[frame] != NULL) + writel (OHCI_INTR_SF, ®s->intrenable); + stat = 0xff; + } + + writel (ints, ®s->intrstatus); + return stat; +} + +/*-------------------------------------------------------------------------*/ + +/*-------------------------------------------------------------------------*/ + +/* De-allocate all resources.. */ + +static void hc_release_ohci (ohci_t *ohci) +{ + dbg ("USB HC release ohci usb-%s", ohci->slot_name); + + if (!ohci->disabled) + hc_reset (ohci); +} + +/*-------------------------------------------------------------------------*/ + +/* + * low level initalisation routine, called from usb.c + */ +static char ohci_inited = 0; + +int usb_lowlevel_init(void) +{ + S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); + S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO(); + + /* + * Set the 48 MHz UPLL clocking. Values are taken from + * "PLL value selection guide", 6-23, s3c2400_UM.pdf. + */ + clk_power->UPLLCON = ((40 << 12) + (1 << 4) + 2); + gpio->MISCCR |= 0x8; /* 1 = use pads related USB for USB host */ + + /* + * Enable USB host clock. + */ + clk_power->CLKCON |= (1 << 4); + + memset (&gohci, 0, sizeof (ohci_t)); + memset (&urb_priv, 0, sizeof (urb_priv_t)); + + /* align the storage */ + if ((__u32)&ghcca[0] & 0xff) { + err("HCCA not aligned!!"); + return -1; + } + phcca = &ghcca[0]; + info("aligned ghcca %p", phcca); + memset(&ohci_dev, 0, sizeof(struct ohci_device)); + if ((__u32)&ohci_dev.ed[0] & 0x7) { + err("EDs not aligned!!"); + return -1; + } + memset(gtd, 0, sizeof(td_t) * (NUM_TD + 1)); + if ((__u32)gtd & 0x7) { + err("TDs not aligned!!"); + return -1; + } + ptd = gtd; + gohci.hcca = phcca; + memset (phcca, 0, sizeof (struct ohci_hcca)); + + gohci.disabled = 1; + gohci.sleeping = 0; + gohci.irq = -1; + gohci.regs = (struct ohci_regs *)S3C24X0_USB_HOST_BASE; + + gohci.flags = 0; + gohci.slot_name = "s3c2400"; + + if (hc_reset (&gohci) < 0) { + hc_release_ohci (&gohci); + /* Initialization failed */ + clk_power->CLKCON &= ~(1 << 4); + return -1; + } + + /* FIXME this is a second HC reset; why?? */ + writel (gohci.hc_control = OHCI_USB_RESET, &gohci.regs->control); + wait_ms (10); + + if (hc_start (&gohci) < 0) { + err ("can't start usb-%s", gohci.slot_name); + hc_release_ohci (&gohci); + /* Initialization failed */ + clk_power->CLKCON &= ~(1 << 4); + return -1; + } + +#ifdef DEBUG + ohci_dump (&gohci, 1); +#else + wait_ms(1); +#endif + ohci_inited = 1; + return 0; +} + +int usb_lowlevel_stop(void) +{ + S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); + + /* this gets called really early - before the controller has */ + /* even been initialized! */ + if (!ohci_inited) + return 0; + /* TODO release any interrupts, etc. */ + /* call hc_release_ohci() here ? */ + hc_reset (&gohci); + /* may not want to do this */ + clk_power->CLKCON &= ~(1 << 4); + return 0; +} + +#endif /* CONFIG_USB_OHCI */ diff --git a/cpu/arm920t/s3c24x0/usb_ohci.h b/cpu/arm920t/s3c24x0/usb_ohci.h new file mode 100644 index 0000000..fab0e65 --- /dev/null +++ b/cpu/arm920t/s3c24x0/usb_ohci.h @@ -0,0 +1,419 @@ +/* + * URB OHCI HCD (Host Controller Driver) for USB. + * + * (C) Copyright 1999 Roman Weissgaerber + * (C) Copyright 2000-2001 David Brownell + * + * usb-ohci.h + */ + + +static int cc_to_error[16] = { + +/* mapping of the OHCI CC status to error codes */ + /* No Error */ 0, + /* CRC Error */ USB_ST_CRC_ERR, + /* Bit Stuff */ USB_ST_BIT_ERR, + /* Data Togg */ USB_ST_CRC_ERR, + /* Stall */ USB_ST_STALLED, + /* DevNotResp */ -1, + /* PIDCheck */ USB_ST_BIT_ERR, + /* UnExpPID */ USB_ST_BIT_ERR, + /* DataOver */ USB_ST_BUF_ERR, + /* DataUnder */ USB_ST_BUF_ERR, + /* reservd */ -1, + /* reservd */ -1, + /* BufferOver */ USB_ST_BUF_ERR, + /* BuffUnder */ USB_ST_BUF_ERR, + /* Not Access */ -1, + /* Not Access */ -1 +}; + +/* ED States */ + +#define ED_NEW 0x00 +#define ED_UNLINK 0x01 +#define ED_OPER 0x02 +#define ED_DEL 0x04 +#define ED_URB_DEL 0x08 + +/* usb_ohci_ed */ +struct ed { + __u32 hwINFO; + __u32 hwTailP; + __u32 hwHeadP; + __u32 hwNextED; + + struct ed *ed_prev; + __u8 int_period; + __u8 int_branch; + __u8 int_load; + __u8 int_interval; + __u8 state; + __u8 type; + __u16 last_iso; + struct ed *ed_rm_list; + + struct usb_device *usb_dev; + __u32 unused[3]; +} __attribute((aligned(16))); +typedef struct ed ed_t; + + +/* TD info field */ +#define TD_CC 0xf0000000 +#define TD_CC_GET(td_p) ((td_p >>28) & 0x0f) +#define TD_CC_SET(td_p, cc) (td_p) = ((td_p) & 0x0fffffff) | (((cc) & 0x0f) << 28) +#define TD_EC 0x0C000000 +#define TD_T 0x03000000 +#define TD_T_DATA0 0x02000000 +#define TD_T_DATA1 0x03000000 +#define TD_T_TOGGLE 0x00000000 +#define TD_R 0x00040000 +#define TD_DI 0x00E00000 +#define TD_DI_SET(X) (((X) & 0x07)<< 21) +#define TD_DP 0x00180000 +#define TD_DP_SETUP 0x00000000 +#define TD_DP_IN 0x00100000 +#define TD_DP_OUT 0x00080000 + +#define TD_ISO 0x00010000 +#define TD_DEL 0x00020000 + +/* CC Codes */ +#define TD_CC_NOERROR 0x00 +#define TD_CC_CRC 0x01 +#define TD_CC_BITSTUFFING 0x02 +#define TD_CC_DATATOGGLEM 0x03 +#define TD_CC_STALL 0x04 +#define TD_DEVNOTRESP 0x05 +#define TD_PIDCHECKFAIL 0x06 +#define TD_UNEXPECTEDPID 0x07 +#define TD_DATAOVERRUN 0x08 +#define TD_DATAUNDERRUN 0x09 +#define TD_BUFFEROVERRUN 0x0C +#define TD_BUFFERUNDERRUN 0x0D +#define TD_NOTACCESSED 0x0F + + +#define MAXPSW 1 + +struct td { + __u32 hwINFO; + __u32 hwCBP; /* Current Buffer Pointer */ + __u32 hwNextTD; /* Next TD Pointer */ + __u32 hwBE; /* Memory Buffer End Pointer */ + + __u16 hwPSW[MAXPSW]; + __u8 unused; + __u8 index; + struct ed *ed; + struct td *next_dl_td; + struct usb_device *usb_dev; + int transfer_len; + __u32 data; + + __u32 unused2[2]; +} __attribute((aligned(32))); +typedef struct td td_t; + +#define OHCI_ED_SKIP (1 << 14) + +/* + * The HCCA (Host Controller Communications Area) is a 256 byte + * structure defined in the OHCI spec. that the host controller is + * told the base address of. It must be 256-byte aligned. + */ + +#define NUM_INTS 32 /* part of the OHCI standard */ +struct ohci_hcca { + __u32 int_table[NUM_INTS]; /* Interrupt ED table */ + __u16 frame_no; /* current frame number */ + __u16 pad1; /* set to 0 on each frame_no change */ + __u32 done_head; /* info returned for an interrupt */ + u8 reserved_for_hc[116]; +} __attribute((aligned(256))); + + +/* + * Maximum number of root hub ports. + */ +#define MAX_ROOT_PORTS 15 /* maximum OHCI root hub ports */ + +/* + * This is the structure of the OHCI controller's memory mapped I/O + * region. This is Memory Mapped I/O. You must use the readl() and + * writel() macros defined in asm/io.h to access these!! + */ +struct ohci_regs { + /* control and status registers */ + __u32 revision; + __u32 control; + __u32 cmdstatus; + __u32 intrstatus; + __u32 intrenable; + __u32 intrdisable; + /* memory pointers */ + __u32 hcca; + __u32 ed_periodcurrent; + __u32 ed_controlhead; + __u32 ed_controlcurrent; + __u32 ed_bulkhead; + __u32 ed_bulkcurrent; + __u32 donehead; + /* frame counters */ + __u32 fminterval; + __u32 fmremaining; + __u32 fmnumber; + __u32 periodicstart; + __u32 lsthresh; + /* Root hub ports */ + struct ohci_roothub_regs { + __u32 a; + __u32 b; + __u32 status; + __u32 portstatus[MAX_ROOT_PORTS]; + } roothub; +} __attribute((aligned(32))); + + +/* OHCI CONTROL AND STATUS REGISTER MASKS */ + +/* + * HcControl (control) register masks + */ +#define OHCI_CTRL_CBSR (3 << 0) /* control/bulk service ratio */ +#define OHCI_CTRL_PLE (1 << 2) /* periodic list enable */ +#define OHCI_CTRL_IE (1 << 3) /* isochronous enable */ +#define OHCI_CTRL_CLE (1 << 4) /* control list enable */ +#define OHCI_CTRL_BLE (1 << 5) /* bulk list enable */ +#define OHCI_CTRL_HCFS (3 << 6) /* host controller functional state */ +#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */ +#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */ +#define OHCI_CTRL_RWE (1 << 10) /* remote wakeup enable */ + +/* pre-shifted values for HCFS */ +# define OHCI_USB_RESET (0 << 6) +# define OHCI_USB_RESUME (1 << 6) +# define OHCI_USB_OPER (2 << 6) +# define OHCI_USB_SUSPEND (3 << 6) + +/* + * HcCommandStatus (cmdstatus) register masks + */ +#define OHCI_HCR (1 << 0) /* host controller reset */ +#define OHCI_CLF (1 << 1) /* control list filled */ +#define OHCI_BLF (1 << 2) /* bulk list filled */ +#define OHCI_OCR (1 << 3) /* ownership change request */ +#define OHCI_SOC (3 << 16) /* scheduling overrun count */ + +/* + * masks used with interrupt registers: + * HcInterruptStatus (intrstatus) + * HcInterruptEnable (intrenable) + * HcInterruptDisable (intrdisable) + */ +#define OHCI_INTR_SO (1 << 0) /* scheduling overrun */ +#define OHCI_INTR_WDH (1 << 1) /* writeback of done_head */ +#define OHCI_INTR_SF (1 << 2) /* start frame */ +#define OHCI_INTR_RD (1 << 3) /* resume detect */ +#define OHCI_INTR_UE (1 << 4) /* unrecoverable error */ +#define OHCI_INTR_FNO (1 << 5) /* frame number overflow */ +#define OHCI_INTR_RHSC (1 << 6) /* root hub status change */ +#define OHCI_INTR_OC (1 << 30) /* ownership change */ +#define OHCI_INTR_MIE (1 << 31) /* master interrupt enable */ + + +/* Virtual Root HUB */ +struct virt_root_hub { + int devnum; /* Address of Root Hub endpoint */ + void *dev; /* was urb */ + void *int_addr; + int send; + int interval; +}; + +/* USB HUB CONSTANTS (not OHCI-specific; see hub.h) */ + +/* destination of request */ +#define RH_INTERFACE 0x01 +#define RH_ENDPOINT 0x02 +#define RH_OTHER 0x03 + +#define RH_CLASS 0x20 +#define RH_VENDOR 0x40 + +/* Requests: bRequest << 8 | bmRequestType */ +#define RH_GET_STATUS 0x0080 +#define RH_CLEAR_FEATURE 0x0100 +#define RH_SET_FEATURE 0x0300 +#define RH_SET_ADDRESS 0x0500 +#define RH_GET_DESCRIPTOR 0x0680 +#define RH_SET_DESCRIPTOR 0x0700 +#define RH_GET_CONFIGURATION 0x0880 +#define RH_SET_CONFIGURATION 0x0900 +#define RH_GET_STATE 0x0280 +#define RH_GET_INTERFACE 0x0A80 +#define RH_SET_INTERFACE 0x0B00 +#define RH_SYNC_FRAME 0x0C80 +/* Our Vendor Specific Request */ +#define RH_SET_EP 0x2000 + + +/* Hub port features */ +#define RH_PORT_CONNECTION 0x00 +#define RH_PORT_ENABLE 0x01 +#define RH_PORT_SUSPEND 0x02 +#define RH_PORT_OVER_CURRENT 0x03 +#define RH_PORT_RESET 0x04 +#define RH_PORT_POWER 0x08 +#define RH_PORT_LOW_SPEED 0x09 + +#define RH_C_PORT_CONNECTION 0x10 +#define RH_C_PORT_ENABLE 0x11 +#define RH_C_PORT_SUSPEND 0x12 +#define RH_C_PORT_OVER_CURRENT 0x13 +#define RH_C_PORT_RESET 0x14 + +/* Hub features */ +#define RH_C_HUB_LOCAL_POWER 0x00 +#define RH_C_HUB_OVER_CURRENT 0x01 + +#define RH_DEVICE_REMOTE_WAKEUP 0x00 +#define RH_ENDPOINT_STALL 0x01 + +#define RH_ACK 0x01 +#define RH_REQ_ERR -1 +#define RH_NACK 0x00 + + +/* OHCI ROOT HUB REGISTER MASKS */ + +/* roothub.portstatus [i] bits */ +#define RH_PS_CCS 0x00000001 /* current connect status */ +#define RH_PS_PES 0x00000002 /* port enable status*/ +#define RH_PS_PSS 0x00000004 /* port suspend status */ +#define RH_PS_POCI 0x00000008 /* port over current indicator */ +#define RH_PS_PRS 0x00000010 /* port reset status */ +#define RH_PS_PPS 0x00000100 /* port power status */ +#define RH_PS_LSDA 0x00000200 /* low speed device attached */ +#define RH_PS_CSC 0x00010000 /* connect status change */ +#define RH_PS_PESC 0x00020000 /* port enable status change */ +#define RH_PS_PSSC 0x00040000 /* port suspend status change */ +#define RH_PS_OCIC 0x00080000 /* over current indicator change */ +#define RH_PS_PRSC 0x00100000 /* port reset status change */ + +/* roothub.status bits */ +#define RH_HS_LPS 0x00000001 /* local power status */ +#define RH_HS_OCI 0x00000002 /* over current indicator */ +#define RH_HS_DRWE 0x00008000 /* device remote wakeup enable */ +#define RH_HS_LPSC 0x00010000 /* local power status change */ +#define RH_HS_OCIC 0x00020000 /* over current indicator change */ +#define RH_HS_CRWE 0x80000000 /* clear remote wakeup enable */ + +/* roothub.b masks */ +#define RH_B_DR 0x0000ffff /* device removable flags */ +#define RH_B_PPCM 0xffff0000 /* port power control mask */ + +/* roothub.a masks */ +#define RH_A_NDP (0xff << 0) /* number of downstream ports */ +#define RH_A_PSM (1 << 8) /* power switching mode */ +#define RH_A_NPS (1 << 9) /* no power switching */ +#define RH_A_DT (1 << 10) /* device type (mbz) */ +#define RH_A_OCPM (1 << 11) /* over current protection mode */ +#define RH_A_NOCP (1 << 12) /* no over current protection */ +#define RH_A_POTPGT (0xff << 24) /* power on to power good time */ + +/* urb */ +#define N_URB_TD 48 +typedef struct +{ + ed_t *ed; + __u16 length; /* number of tds associated with this request */ + __u16 td_cnt; /* number of tds already serviced */ + int state; + unsigned long pipe; + int actual_length; + td_t *td[N_URB_TD]; /* list pointer to all corresponding TDs associated with this request */ +} urb_priv_t; +#define URB_DEL 1 + +/* + * This is the full ohci controller description + * + * Note how the "proper" USB information is just + * a subset of what the full implementation needs. (Linus) + */ + + +typedef struct ohci { + struct ohci_hcca *hcca; /* hcca */ + /*dma_addr_t hcca_dma;*/ + + int irq; + int disabled; /* e.g. got a UE, we're hung */ + int sleeping; + unsigned long flags; /* for HC bugs */ + + struct ohci_regs *regs; /* OHCI controller's memory */ + + ed_t *ed_rm_list[2]; /* lists of all endpoints to be removed */ + ed_t *ed_bulktail; /* last endpoint of bulk list */ + ed_t *ed_controltail; /* last endpoint of control list */ + int intrstatus; + __u32 hc_control; /* copy of the hc control reg */ + struct usb_device *dev[32]; + struct virt_root_hub rh; + + const char *slot_name; +} ohci_t; + +#define NUM_EDS 8 /* num of preallocated endpoint descriptors */ + +struct ohci_device { + ed_t ed[NUM_EDS]; + int ed_cnt; +}; + +/* hcd */ +/* endpoint */ +static int ep_link(ohci_t * ohci, ed_t * ed); +static int ep_unlink(ohci_t * ohci, ed_t * ed); +static ed_t * ep_add_ed(struct usb_device * usb_dev, unsigned long pipe); + +/*-------------------------------------------------------------------------*/ + +/* we need more TDs than EDs */ +#define NUM_TD 64 + +/* +1 so we can align the storage */ +td_t gtd[NUM_TD+1]; +/* pointers to aligned storage */ +td_t *ptd; + +/* TDs ... */ +static inline struct td * +td_alloc (struct usb_device *usb_dev) +{ + int i; + struct td *td; + + td = NULL; + for (i = 0; i < NUM_TD; i++) + { + if (ptd[i].usb_dev == NULL) + { + td = &ptd[i]; + td->usb_dev = usb_dev; + break; + } + } + + return td; +} + +static inline void +ed_free (struct ed *ed) +{ + ed->usb_dev = NULL; +} diff --git a/cpu/arm920t/s3c24x0_interrupts.c b/cpu/arm920t/s3c24x0_interrupts.c deleted file mode 100644 index 92298b0..0000000 --- a/cpu/arm920t/s3c24x0_interrupts.c +++ /dev/null @@ -1,180 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Alex Zuepke - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) - -#include -#if defined(CONFIG_S3C2400) -#include -#elif defined(CONFIG_S3C2410) -#include -#endif - -extern void reset_cpu(ulong addr); -int timer_load_val = 0; - -/* macro to read the 16 bit timer */ -static inline ulong READ_TIMER(void) -{ - S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); - - return (timers->TCNTO4 & 0xffff); -} - -static ulong timestamp; -static ulong lastdec; - -int interrupt_init (void) -{ - S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); - - /* use PWM Timer 4 because it has no output */ - /* prescaler for Timer 4 is 16 */ - timers->TCFG0 = 0x0f00; - if (timer_load_val == 0) - { - /* - * for 10 ms clock period @ PCLK with 4 bit divider = 1/2 - * (default) and prescaler = 16. Should be 10390 - * @33.25MHz and 15625 @ 50 MHz - */ - timer_load_val = get_PCLK()/(2 * 16 * 100); - } - /* load value for 10 ms timeout */ - lastdec = timers->TCNTB4 = timer_load_val; - /* auto load, manual update of Timer 4 */ - timers->TCON = (timers->TCON & ~0x0700000) | 0x600000; - /* auto load, start Timer 4 */ - timers->TCON = (timers->TCON & ~0x0700000) | 0x500000; - timestamp = 0; - - return (0); -} - -/* - * timer without interrupts - */ - -void reset_timer (void) -{ - reset_timer_masked (); -} - -ulong get_timer (ulong base) -{ - return get_timer_masked () - base; -} - -void set_timer (ulong t) -{ - timestamp = t; -} - -void udelay (unsigned long usec) -{ - ulong tmo; - ulong start = get_timer(0); - - tmo = usec / 1000; - tmo *= (timer_load_val * 100); - tmo /= 1000; - - while ((ulong)(get_timer_masked () - start) < tmo) - /*NOP*/; -} - -void reset_timer_masked (void) -{ - /* reset time */ - lastdec = READ_TIMER(); - timestamp = 0; -} - -ulong get_timer_masked (void) -{ - ulong now = READ_TIMER(); - - if (lastdec >= now) { - /* normal mode */ - timestamp += lastdec - now; - } else { - /* we have an overflow ... */ - timestamp += lastdec + timer_load_val - now; - } - lastdec = now; - - return timestamp; -} - -void udelay_masked (unsigned long usec) -{ - ulong tmo; - - tmo = usec / 1000; - tmo *= (timer_load_val * 100); - tmo /= 1000; - - reset_timer_masked (); - - while (get_timer_masked () < tmo) - /*NOP*/; -} - -/* - * This function is derived from PowerPC code (read timebase as long long). - * On ARM it just returns the timer value. - */ -unsigned long long get_ticks(void) -{ - return get_timer(0); -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk (void) -{ - ulong tbclk; - -#if defined(CONFIG_SMDK2400) || defined(CONFIG_TRAB) - tbclk = timer_load_val * 100; -#elif defined(CONFIG_SMDK2410) || defined(CONFIG_VCMA9) - tbclk = CFG_HZ; -#else -# error "tbclk not configured" -#endif - - return tbclk; -} - -#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/s3c24x0_serial.c b/cpu/arm920t/s3c24x0_serial.c deleted file mode 100644 index 8327443..0000000 --- a/cpu/arm920t/s3c24x0_serial.c +++ /dev/null @@ -1,182 +0,0 @@ -/* - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#include -#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) - -#if defined(CONFIG_S3C2400) || defined(CONFIG_TRAB) -#include -#elif defined(CONFIG_S3C2410) -#include -#endif - -#ifdef CONFIG_SERIAL1 -#define UART_NR S3C24X0_UART0 - -#elif defined(CONFIG_SERIAL2) -# if defined(CONFIG_TRAB) -# error "TRAB supports only CONFIG_SERIAL1" -# endif -#define UART_NR S3C24X0_UART1 - -#elif defined(CONFIG_SERIAL3) -# if defined(CONFIG_TRAB) -# #error "TRAB supports only CONFIG_SERIAL1" -# endif -#define UART_NR S3C24X0_UART2 - -#else -#error "Bad: you didn't configure serial ..." -#endif - -void serial_setbrg (void) -{ - DECLARE_GLOBAL_DATA_PTR; - S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); - int i; - unsigned int reg = 0; - - /* value is calculated so : (int)(PCLK/16./baudrate) -1 */ - reg = get_PCLK() / (16 * gd->baudrate) - 1; - - /* FIFO enable, Tx/Rx FIFO clear */ - uart->UFCON = 0x07; - uart->UMCON = 0x0; - /* Normal,No parity,1 stop,8 bit */ - uart->ULCON = 0x3; - /* - * tx=level,rx=edge,disable timeout int.,enable rx error int., - * normal,interrupt or polling - */ - uart->UCON = 0x245; - uart->UBRDIV = reg; - -#ifdef CONFIG_HWFLOW - uart->UMCON = 0x1; /* RTS up */ -#endif - for (i = 0; i < 100; i++); -} - -/* - * Initialise the serial port with the given baudrate. The settings - * are always 8 data bits, no parity, 1 stop bit, no start bits. - * - */ -int serial_init (void) -{ - serial_setbrg (); - - return (0); -} - -/* - * Read a single byte from the serial port. Returns 1 on success, 0 - * otherwise. When the function is succesfull, the character read is - * written into its argument c. - */ -int serial_getc (void) -{ - S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); - - /* wait for character to arrive */ - while (!(uart->UTRSTAT & 0x1)); - - return uart->URXH & 0xff; -} - -#ifdef CONFIG_HWFLOW -static int hwflow = 0; /* turned off by default */ -int hwflow_onoff(int on) -{ - switch(on) { - case 0: - default: - break; /* return current */ - case 1: - hwflow = 1; /* turn on */ - break; - case -1: - hwflow = 0; /* turn off */ - break; - } - return hwflow; -} -#endif - -#ifdef CONFIG_MODEM_SUPPORT -static int be_quiet = 0; -void disable_putc(void) -{ - be_quiet = 1; -} - -void enable_putc(void) -{ - be_quiet = 0; -} -#endif - - -/* - * Output a single byte to the serial port. - */ -void serial_putc (const char c) -{ - S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); -#ifdef CONFIG_MODEM_SUPPORT - if (be_quiet) - return; -#endif - - /* wait for room in the tx FIFO */ - while (!(uart->UTRSTAT & 0x2)); - -#ifdef CONFIG_HWFLOW - /* Wait for CTS up */ - while(hwflow && !(uart->UMSTAT & 0x1)) - ; -#endif - - uart->UTXH = c; - - /* If \n, also do \r */ - if (c == '\n') - serial_putc ('\r'); -} - -/* - * Test whether a character is in the RX buffer - */ -int serial_tstc (void) -{ - S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR); - - return uart->UTRSTAT & 0x1; -} - -void -serial_puts (const char *s) -{ - while (*s) { - serial_putc (*s++); - } -} - -#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/s3c24x0_speed.c b/cpu/arm920t/s3c24x0_speed.c deleted file mode 100644 index e0dca62..0000000 --- a/cpu/arm920t/s3c24x0_speed.c +++ /dev/null @@ -1,101 +0,0 @@ -/* - * (C) Copyright 2001-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2002 - * David Mueller, ELSOFT AG, d.mueller@elsoft.ch - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* This code should work for both the S3C2400 and the S3C2410 - * as they seem to have the same PLL and clock machinery inside. - * The different address mapping is handled by the s3c24xx.h files below. - */ - -#include -#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) - -#if defined(CONFIG_S3C2400) -#include -#elif defined(CONFIG_S3C2410) -#include -#endif - -#define MPLL 0 -#define UPLL 1 - -/* ------------------------------------------------------------------------- */ -/* NOTE: This describes the proper use of this file. - * - * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL. - * - * get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of - * the specified bus in HZ. - */ -/* ------------------------------------------------------------------------- */ - -static ulong get_PLLCLK(int pllreg) -{ - S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); - ulong r, m, p, s; - - if (pllreg == MPLL) - r = clk_power->MPLLCON; - else if (pllreg == UPLL) - r = clk_power->UPLLCON; - else - hang(); - - m = ((r & 0xFF000) >> 12) + 8; - p = ((r & 0x003F0) >> 4) + 2; - s = r & 0x3; - - return((CONFIG_SYS_CLK_FREQ * m) / (p << s)); -} - -/* return FCLK frequency */ -ulong get_FCLK(void) -{ - return(get_PLLCLK(MPLL)); -} - -/* return HCLK frequency */ -ulong get_HCLK(void) -{ - S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); - - return((clk_power->CLKDIVN & 0x2) ? get_FCLK()/2 : get_FCLK()); -} - -/* return PCLK frequency */ -ulong get_PCLK(void) -{ - S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); - - return((clk_power->CLKDIVN & 0x1) ? get_HCLK()/2 : get_HCLK()); -} - -/* return UCLK frequency */ -ulong get_UCLK(void) -{ - return(get_PLLCLK(UPLL)); -} - -#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/usb_ohci.c b/cpu/arm920t/usb_ohci.c deleted file mode 100644 index 6f4a9f7..0000000 --- a/cpu/arm920t/usb_ohci.c +++ /dev/null @@ -1,1630 +0,0 @@ -/* - * URB OHCI HCD (Host Controller Driver) for USB on the S3C2400. - * - * (C) Copyright 2003 - * Gary Jennejohn, DENX Software Engineering - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - * - * Note: Part of this code has been derived from linux - * - */ -/* - * IMPORTANT NOTES - * 1 - you MUST define LITTLEENDIAN in the configuration file for the - * board or this driver will NOT work! - * 2 - this driver is intended for use with USB Mass Storage Devices - * (BBB) ONLY. There is NO support for Interrupt or Isochronous pipes! - */ - -#include -/* #include no PCI on the S3C24X0 */ - -#ifdef CONFIG_USB_OHCI - -#if defined(CONFIG_S3C2400) -#include -#elif defined(CONFIG_S3C2410) -#include -#endif - -#include -#include -#include "usb_ohci.h" - -#define OHCI_USE_NPS /* force NoPowerSwitching mode */ -#undef OHCI_VERBOSE_DEBUG /* not always helpful */ - - -/* For initializing controller (mask in an HCFS mode too) */ -#define OHCI_CONTROL_INIT \ - (OHCI_CTRL_CBSR & 0x3) | OHCI_CTRL_IE | OHCI_CTRL_PLE - -#define readl(a) (*((vu_long *)(a))) -#define writel(a, b) (*((vu_long *)(b)) = ((vu_long)a)) - -#define min_t(type,x,y) ({ type __x = (x); type __y = (y); __x < __y ? __x: __y; }) - -#undef DEBUG -#ifdef DEBUG -#define dbg(format, arg...) printf("DEBUG: " format "\n", ## arg) -#else -#define dbg(format, arg...) do {} while(0) -#endif /* DEBUG */ -#define err(format, arg...) printf("ERROR: " format "\n", ## arg) -#undef SHOW_INFO -#ifdef SHOW_INFO -#define info(format, arg...) printf("INFO: " format "\n", ## arg) -#else -#define info(format, arg...) do {} while(0) -#endif - -#define m16_swap(x) swap_16(x) -#define m32_swap(x) swap_32(x) - -/* global ohci_t */ -static ohci_t gohci; -/* this must be aligned to a 256 byte boundary */ -struct ohci_hcca ghcca[1]; -/* a pointer to the aligned storage */ -struct ohci_hcca *phcca; -/* this allocates EDs for all possible endpoints */ -struct ohci_device ohci_dev; -/* urb_priv */ -urb_priv_t urb_priv; -/* RHSC flag */ -int got_rhsc; -/* device which was disconnected */ -struct usb_device *devgone; - -/*-------------------------------------------------------------------------*/ - -/* AMD-756 (D2 rev) reports corrupt register contents in some cases. - * The erratum (#4) description is incorrect. AMD's workaround waits - * till some bits (mostly reserved) are clear; ok for all revs. - */ -#define OHCI_QUIRK_AMD756 0xabcd -#define read_roothub(hc, register, mask) ({ \ - u32 temp = readl (&hc->regs->roothub.register); \ - if (hc->flags & OHCI_QUIRK_AMD756) \ - while (temp & mask) \ - temp = readl (&hc->regs->roothub.register); \ - temp; }) - -static u32 roothub_a (struct ohci *hc) - { return read_roothub (hc, a, 0xfc0fe000); } -static inline u32 roothub_b (struct ohci *hc) - { return readl (&hc->regs->roothub.b); } -static inline u32 roothub_status (struct ohci *hc) - { return readl (&hc->regs->roothub.status); } -static u32 roothub_portstatus (struct ohci *hc, int i) - { return read_roothub (hc, portstatus [i], 0xffe0fce0); } - - -/* forward declaration */ -static int hc_interrupt (void); -static void -td_submit_job (struct usb_device * dev, unsigned long pipe, void * buffer, - int transfer_len, struct devrequest * setup, urb_priv_t * urb, int interval); - -/*-------------------------------------------------------------------------* - * URB support functions - *-------------------------------------------------------------------------*/ - -/* free HCD-private data associated with this URB */ - -static void urb_free_priv (urb_priv_t * urb) -{ - int i; - int last; - struct td * td; - - last = urb->length - 1; - if (last >= 0) { - for (i = 0; i <= last; i++) { - td = urb->td[i]; - if (td) { - td->usb_dev = NULL; - urb->td[i] = NULL; - } - } - } -} - -/*-------------------------------------------------------------------------*/ - -#ifdef DEBUG -static int sohci_get_current_frame_number (struct usb_device * dev); - -/* debug| print the main components of an URB - * small: 0) header + data packets 1) just header */ - -static void pkt_print (struct usb_device * dev, unsigned long pipe, void * buffer, - int transfer_len, struct devrequest * setup, char * str, int small) -{ - urb_priv_t * purb = &urb_priv; - - dbg("%s URB:[%4x] dev:%2d,ep:%2d-%c,type:%s,len:%d/%d stat:%#lx", - str, - sohci_get_current_frame_number (dev), - usb_pipedevice (pipe), - usb_pipeendpoint (pipe), - usb_pipeout (pipe)? 'O': 'I', - usb_pipetype (pipe) < 2? (usb_pipeint (pipe)? "INTR": "ISOC"): - (usb_pipecontrol (pipe)? "CTRL": "BULK"), - purb->actual_length, - transfer_len, dev->status); -#ifdef OHCI_VERBOSE_DEBUG - if (!small) { - int i, len; - - if (usb_pipecontrol (pipe)) { - printf (__FILE__ ": cmd(8):"); - for (i = 0; i < 8 ; i++) - printf (" %02x", ((__u8 *) setup) [i]); - printf ("\n"); - } - if (transfer_len > 0 && buffer) { - printf (__FILE__ ": data(%d/%d):", - purb->actual_length, - transfer_len); - len = usb_pipeout (pipe)? - transfer_len: purb->actual_length; - for (i = 0; i < 16 && i < len; i++) - printf (" %02x", ((__u8 *) buffer) [i]); - printf ("%s\n", i < len? "...": ""); - } - } -#endif -} - -/* just for debugging; prints non-empty branches of the int ed tree inclusive iso eds*/ -void ep_print_int_eds (ohci_t *ohci, char * str) { - int i, j; - __u32 * ed_p; - for (i= 0; i < 32; i++) { - j = 5; - ed_p = &(ohci->hcca->int_table [i]); - if (*ed_p == 0) - continue; - printf (__FILE__ ": %s branch int %2d(%2x):", str, i, i); - while (*ed_p != 0 && j--) { - ed_t *ed = (ed_t *)m32_swap(ed_p); - printf (" ed: %4x;", ed->hwINFO); - ed_p = &ed->hwNextED; - } - printf ("\n"); - } -} - -static void ohci_dump_intr_mask (char *label, __u32 mask) -{ - dbg ("%s: 0x%08x%s%s%s%s%s%s%s%s%s", - label, - mask, - (mask & OHCI_INTR_MIE) ? " MIE" : "", - (mask & OHCI_INTR_OC) ? " OC" : "", - (mask & OHCI_INTR_RHSC) ? " RHSC" : "", - (mask & OHCI_INTR_FNO) ? " FNO" : "", - (mask & OHCI_INTR_UE) ? " UE" : "", - (mask & OHCI_INTR_RD) ? " RD" : "", - (mask & OHCI_INTR_SF) ? " SF" : "", - (mask & OHCI_INTR_WDH) ? " WDH" : "", - (mask & OHCI_INTR_SO) ? " SO" : "" - ); -} - -static void maybe_print_eds (char *label, __u32 value) -{ - ed_t *edp = (ed_t *)value; - - if (value) { - dbg ("%s %08x", label, value); - dbg ("%08x", edp->hwINFO); - dbg ("%08x", edp->hwTailP); - dbg ("%08x", edp->hwHeadP); - dbg ("%08x", edp->hwNextED); - } -} - -static char * hcfs2string (int state) -{ - switch (state) { - case OHCI_USB_RESET: return "reset"; - case OHCI_USB_RESUME: return "resume"; - case OHCI_USB_OPER: return "operational"; - case OHCI_USB_SUSPEND: return "suspend"; - } - return "?"; -} - -/* dump control and status registers */ -static void ohci_dump_status (ohci_t *controller) -{ - struct ohci_regs *regs = controller->regs; - __u32 temp; - - temp = readl (®s->revision) & 0xff; - if (temp != 0x10) - dbg ("spec %d.%d", (temp >> 4), (temp & 0x0f)); - - temp = readl (®s->control); - dbg ("control: 0x%08x%s%s%s HCFS=%s%s%s%s%s CBSR=%d", temp, - (temp & OHCI_CTRL_RWE) ? " RWE" : "", - (temp & OHCI_CTRL_RWC) ? " RWC" : "", - (temp & OHCI_CTRL_IR) ? " IR" : "", - hcfs2string (temp & OHCI_CTRL_HCFS), - (temp & OHCI_CTRL_BLE) ? " BLE" : "", - (temp & OHCI_CTRL_CLE) ? " CLE" : "", - (temp & OHCI_CTRL_IE) ? " IE" : "", - (temp & OHCI_CTRL_PLE) ? " PLE" : "", - temp & OHCI_CTRL_CBSR - ); - - temp = readl (®s->cmdstatus); - dbg ("cmdstatus: 0x%08x SOC=%d%s%s%s%s", temp, - (temp & OHCI_SOC) >> 16, - (temp & OHCI_OCR) ? " OCR" : "", - (temp & OHCI_BLF) ? " BLF" : "", - (temp & OHCI_CLF) ? " CLF" : "", - (temp & OHCI_HCR) ? " HCR" : "" - ); - - ohci_dump_intr_mask ("intrstatus", readl (®s->intrstatus)); - ohci_dump_intr_mask ("intrenable", readl (®s->intrenable)); - - maybe_print_eds ("ed_periodcurrent", readl (®s->ed_periodcurrent)); - - maybe_print_eds ("ed_controlhead", readl (®s->ed_controlhead)); - maybe_print_eds ("ed_controlcurrent", readl (®s->ed_controlcurrent)); - - maybe_print_eds ("ed_bulkhead", readl (®s->ed_bulkhead)); - maybe_print_eds ("ed_bulkcurrent", readl (®s->ed_bulkcurrent)); - - maybe_print_eds ("donehead", readl (®s->donehead)); -} - -static void ohci_dump_roothub (ohci_t *controller, int verbose) -{ - __u32 temp, ndp, i; - - temp = roothub_a (controller); - ndp = (temp & RH_A_NDP); - - if (verbose) { - dbg ("roothub.a: %08x POTPGT=%d%s%s%s%s%s NDP=%d", temp, - ((temp & RH_A_POTPGT) >> 24) & 0xff, - (temp & RH_A_NOCP) ? " NOCP" : "", - (temp & RH_A_OCPM) ? " OCPM" : "", - (temp & RH_A_DT) ? " DT" : "", - (temp & RH_A_NPS) ? " NPS" : "", - (temp & RH_A_PSM) ? " PSM" : "", - ndp - ); - temp = roothub_b (controller); - dbg ("roothub.b: %08x PPCM=%04x DR=%04x", - temp, - (temp & RH_B_PPCM) >> 16, - (temp & RH_B_DR) - ); - temp = roothub_status (controller); - dbg ("roothub.status: %08x%s%s%s%s%s%s", - temp, - (temp & RH_HS_CRWE) ? " CRWE" : "", - (temp & RH_HS_OCIC) ? " OCIC" : "", - (temp & RH_HS_LPSC) ? " LPSC" : "", - (temp & RH_HS_DRWE) ? " DRWE" : "", - (temp & RH_HS_OCI) ? " OCI" : "", - (temp & RH_HS_LPS) ? " LPS" : "" - ); - } - - for (i = 0; i < ndp; i++) { - temp = roothub_portstatus (controller, i); - dbg ("roothub.portstatus [%d] = 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s", - i, - temp, - (temp & RH_PS_PRSC) ? " PRSC" : "", - (temp & RH_PS_OCIC) ? " OCIC" : "", - (temp & RH_PS_PSSC) ? " PSSC" : "", - (temp & RH_PS_PESC) ? " PESC" : "", - (temp & RH_PS_CSC) ? " CSC" : "", - - (temp & RH_PS_LSDA) ? " LSDA" : "", - (temp & RH_PS_PPS) ? " PPS" : "", - (temp & RH_PS_PRS) ? " PRS" : "", - (temp & RH_PS_POCI) ? " POCI" : "", - (temp & RH_PS_PSS) ? " PSS" : "", - - (temp & RH_PS_PES) ? " PES" : "", - (temp & RH_PS_CCS) ? " CCS" : "" - ); - } -} - -static void ohci_dump (ohci_t *controller, int verbose) -{ - dbg ("OHCI controller usb-%s state", controller->slot_name); - - /* dumps some of the state we know about */ - ohci_dump_status (controller); - if (verbose) - ep_print_int_eds (controller, "hcca"); - dbg ("hcca frame #%04x", controller->hcca->frame_no); - ohci_dump_roothub (controller, 1); -} - - -#endif /* DEBUG */ - -/*-------------------------------------------------------------------------* - * Interface functions (URB) - *-------------------------------------------------------------------------*/ - -/* get a transfer request */ - -int sohci_submit_job(struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len, struct devrequest *setup, int interval) -{ - ohci_t *ohci; - ed_t * ed; - urb_priv_t *purb_priv; - int i, size = 0; - - ohci = &gohci; - - /* when controller's hung, permit only roothub cleanup attempts - * such as powering down ports */ - if (ohci->disabled) { - err("sohci_submit_job: EPIPE"); - return -1; - } - - /* every endpoint has a ed, locate and fill it */ - if (!(ed = ep_add_ed (dev, pipe))) { - err("sohci_submit_job: ENOMEM"); - return -1; - } - - /* for the private part of the URB we need the number of TDs (size) */ - switch (usb_pipetype (pipe)) { - case PIPE_BULK: /* one TD for every 4096 Byte */ - size = (transfer_len - 1) / 4096 + 1; - break; - case PIPE_CONTROL: /* 1 TD for setup, 1 for ACK and 1 for every 4096 B */ - size = (transfer_len == 0)? 2: - (transfer_len - 1) / 4096 + 3; - break; - } - - if (size >= (N_URB_TD - 1)) { - err("need %d TDs, only have %d", size, N_URB_TD); - return -1; - } - purb_priv = &urb_priv; - purb_priv->pipe = pipe; - - /* fill the private part of the URB */ - purb_priv->length = size; - purb_priv->ed = ed; - purb_priv->actual_length = 0; - - /* allocate the TDs */ - /* note that td[0] was allocated in ep_add_ed */ - for (i = 0; i < size; i++) { - purb_priv->td[i] = td_alloc (dev); - if (!purb_priv->td[i]) { - purb_priv->length = i; - urb_free_priv (purb_priv); - err("sohci_submit_job: ENOMEM"); - return -1; - } - } - - if (ed->state == ED_NEW || (ed->state & ED_DEL)) { - urb_free_priv (purb_priv); - err("sohci_submit_job: EINVAL"); - return -1; - } - - /* link the ed into a chain if is not already */ - if (ed->state != ED_OPER) - ep_link (ohci, ed); - - /* fill the TDs and link it to the ed */ - td_submit_job(dev, pipe, buffer, transfer_len, setup, purb_priv, interval); - - return 0; -} - -/*-------------------------------------------------------------------------*/ - -#ifdef DEBUG -/* tell us the current USB frame number */ - -static int sohci_get_current_frame_number (struct usb_device *usb_dev) -{ - ohci_t *ohci = &gohci; - - return m16_swap (ohci->hcca->frame_no); -} -#endif - -/*-------------------------------------------------------------------------* - * ED handling functions - *-------------------------------------------------------------------------*/ - -/* link an ed into one of the HC chains */ - -static int ep_link (ohci_t *ohci, ed_t *edi) -{ - volatile ed_t *ed = edi; - - ed->state = ED_OPER; - - switch (ed->type) { - case PIPE_CONTROL: - ed->hwNextED = 0; - if (ohci->ed_controltail == NULL) { - writel (ed, &ohci->regs->ed_controlhead); - } else { - ohci->ed_controltail->hwNextED = m32_swap (ed); - } - ed->ed_prev = ohci->ed_controltail; - if (!ohci->ed_controltail && !ohci->ed_rm_list[0] && - !ohci->ed_rm_list[1] && !ohci->sleeping) { - ohci->hc_control |= OHCI_CTRL_CLE; - writel (ohci->hc_control, &ohci->regs->control); - } - ohci->ed_controltail = edi; - break; - - case PIPE_BULK: - ed->hwNextED = 0; - if (ohci->ed_bulktail == NULL) { - writel (ed, &ohci->regs->ed_bulkhead); - } else { - ohci->ed_bulktail->hwNextED = m32_swap (ed); - } - ed->ed_prev = ohci->ed_bulktail; - if (!ohci->ed_bulktail && !ohci->ed_rm_list[0] && - !ohci->ed_rm_list[1] && !ohci->sleeping) { - ohci->hc_control |= OHCI_CTRL_BLE; - writel (ohci->hc_control, &ohci->regs->control); - } - ohci->ed_bulktail = edi; - break; - } - return 0; -} - -/*-------------------------------------------------------------------------*/ - -/* unlink an ed from one of the HC chains. - * just the link to the ed is unlinked. - * the link from the ed still points to another operational ed or 0 - * so the HC can eventually finish the processing of the unlinked ed */ - -static int ep_unlink (ohci_t *ohci, ed_t *ed) -{ - ed->hwINFO |= m32_swap (OHCI_ED_SKIP); - - switch (ed->type) { - case PIPE_CONTROL: - if (ed->ed_prev == NULL) { - if (!ed->hwNextED) { - ohci->hc_control &= ~OHCI_CTRL_CLE; - writel (ohci->hc_control, &ohci->regs->control); - } - writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_controlhead); - } else { - ed->ed_prev->hwNextED = ed->hwNextED; - } - if (ohci->ed_controltail == ed) { - ohci->ed_controltail = ed->ed_prev; - } else { - ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev; - } - break; - - case PIPE_BULK: - if (ed->ed_prev == NULL) { - if (!ed->hwNextED) { - ohci->hc_control &= ~OHCI_CTRL_BLE; - writel (ohci->hc_control, &ohci->regs->control); - } - writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_bulkhead); - } else { - ed->ed_prev->hwNextED = ed->hwNextED; - } - if (ohci->ed_bulktail == ed) { - ohci->ed_bulktail = ed->ed_prev; - } else { - ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev; - } - break; - } - ed->state = ED_UNLINK; - return 0; -} - - -/*-------------------------------------------------------------------------*/ - -/* add/reinit an endpoint; this should be done once at the usb_set_configuration command, - * but the USB stack is a little bit stateless so we do it at every transaction - * if the state of the ed is ED_NEW then a dummy td is added and the state is changed to ED_UNLINK - * in all other cases the state is left unchanged - * the ed info fields are setted anyway even though most of them should not change */ - -static ed_t * ep_add_ed (struct usb_device *usb_dev, unsigned long pipe) -{ - td_t *td; - ed_t *ed_ret; - volatile ed_t *ed; - - ed = ed_ret = &ohci_dev.ed[(usb_pipeendpoint (pipe) << 1) | - (usb_pipecontrol (pipe)? 0: usb_pipeout (pipe))]; - - if ((ed->state & ED_DEL) || (ed->state & ED_URB_DEL)) { - err("ep_add_ed: pending delete"); - /* pending delete request */ - return NULL; - } - - if (ed->state == ED_NEW) { - ed->hwINFO = m32_swap (OHCI_ED_SKIP); /* skip ed */ - /* dummy td; end of td list for ed */ - td = td_alloc (usb_dev); - ed->hwTailP = m32_swap (td); - ed->hwHeadP = ed->hwTailP; - ed->state = ED_UNLINK; - ed->type = usb_pipetype (pipe); - ohci_dev.ed_cnt++; - } - - ed->hwINFO = m32_swap (usb_pipedevice (pipe) - | usb_pipeendpoint (pipe) << 7 - | (usb_pipeisoc (pipe)? 0x8000: 0) - | (usb_pipecontrol (pipe)? 0: (usb_pipeout (pipe)? 0x800: 0x1000)) - | usb_pipeslow (pipe) << 13 - | usb_maxpacket (usb_dev, pipe) << 16); - - return ed_ret; -} - -/*-------------------------------------------------------------------------* - * TD handling functions - *-------------------------------------------------------------------------*/ - -/* enqueue next TD for this URB (OHCI spec 5.2.8.2) */ - -static void td_fill (ohci_t *ohci, unsigned int info, - void *data, int len, - struct usb_device *dev, int index, urb_priv_t *urb_priv) -{ - volatile td_t *td, *td_pt; -#ifdef OHCI_FILL_TRACE - int i; -#endif - - if (index > urb_priv->length) { - err("index > length"); - return; - } - /* use this td as the next dummy */ - td_pt = urb_priv->td [index]; - td_pt->hwNextTD = 0; - - /* fill the old dummy TD */ - td = urb_priv->td [index] = (td_t *)(m32_swap (urb_priv->ed->hwTailP) & ~0xf); - - td->ed = urb_priv->ed; - td->next_dl_td = NULL; - td->index = index; - td->data = (__u32)data; -#ifdef OHCI_FILL_TRACE - if ((usb_pipetype(urb_priv->pipe) == PIPE_BULK) && usb_pipeout(urb_priv->pipe)) { - for (i = 0; i < len; i++) - printf("td->data[%d] %#2x ",i, ((unsigned char *)td->data)[i]); - printf("\n"); - } -#endif - if (!len) - data = 0; - - td->hwINFO = m32_swap (info); - td->hwCBP = m32_swap (data); - if (data) - td->hwBE = m32_swap (data + len - 1); - else - td->hwBE = 0; - td->hwNextTD = m32_swap (td_pt); - td->hwPSW [0] = m16_swap (((__u32)data & 0x0FFF) | 0xE000); - - /* append to queue */ - td->ed->hwTailP = td->hwNextTD; -} - -/*-------------------------------------------------------------------------*/ - -/* prepare all TDs of a transfer */ - -static void td_submit_job (struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len, struct devrequest *setup, urb_priv_t *urb, int interval) -{ - ohci_t *ohci = &gohci; - int data_len = transfer_len; - void *data; - int cnt = 0; - __u32 info = 0; - unsigned int toggle = 0; - - /* OHCI handles the DATA-toggles itself, we just use the USB-toggle bits for reseting */ - if(usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe))) { - toggle = TD_T_TOGGLE; - } else { - toggle = TD_T_DATA0; - usb_settoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe), 1); - } - urb->td_cnt = 0; - if (data_len) - data = buffer; - else - data = 0; - - switch (usb_pipetype (pipe)) { - case PIPE_BULK: - info = usb_pipeout (pipe)? - TD_CC | TD_DP_OUT : TD_CC | TD_DP_IN ; - while(data_len > 4096) { - td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, 4096, dev, cnt, urb); - data += 4096; data_len -= 4096; cnt++; - } - info = usb_pipeout (pipe)? - TD_CC | TD_DP_OUT : TD_CC | TD_R | TD_DP_IN ; - td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, data_len, dev, cnt, urb); - cnt++; - - if (!ohci->sleeping) - writel (OHCI_BLF, &ohci->regs->cmdstatus); /* start bulk list */ - break; - - case PIPE_CONTROL: - info = TD_CC | TD_DP_SETUP | TD_T_DATA0; - td_fill (ohci, info, setup, 8, dev, cnt++, urb); - if (data_len > 0) { - info = usb_pipeout (pipe)? - TD_CC | TD_R | TD_DP_OUT | TD_T_DATA1 : TD_CC | TD_R | TD_DP_IN | TD_T_DATA1; - /* NOTE: mishandles transfers >8K, some >4K */ - td_fill (ohci, info, data, data_len, dev, cnt++, urb); - } - info = usb_pipeout (pipe)? - TD_CC | TD_DP_IN | TD_T_DATA1: TD_CC | TD_DP_OUT | TD_T_DATA1; - td_fill (ohci, info, data, 0, dev, cnt++, urb); - if (!ohci->sleeping) - writel (OHCI_CLF, &ohci->regs->cmdstatus); /* start Control list */ - break; - } - if (urb->length != cnt) - dbg("TD LENGTH %d != CNT %d", urb->length, cnt); -} - -/*-------------------------------------------------------------------------* - * Done List handling functions - *-------------------------------------------------------------------------*/ - - -/* calculate the transfer length and update the urb */ - -static void dl_transfer_length(td_t * td) -{ - __u32 tdINFO, tdBE, tdCBP; - urb_priv_t *lurb_priv = &urb_priv; - - tdINFO = m32_swap (td->hwINFO); - tdBE = m32_swap (td->hwBE); - tdCBP = m32_swap (td->hwCBP); - - - if (!(usb_pipetype (lurb_priv->pipe) == PIPE_CONTROL && - ((td->index == 0) || (td->index == lurb_priv->length - 1)))) { - if (tdBE != 0) { - if (td->hwCBP == 0) - lurb_priv->actual_length += tdBE - td->data + 1; - else - lurb_priv->actual_length += tdCBP - td->data; - } - } -} - -/*-------------------------------------------------------------------------*/ - -/* replies to the request have to be on a FIFO basis so - * we reverse the reversed done-list */ - -static td_t * dl_reverse_done_list (ohci_t *ohci) -{ - __u32 td_list_hc; - td_t *td_rev = NULL; - td_t *td_list = NULL; - urb_priv_t *lurb_priv = NULL; - - td_list_hc = m32_swap (ohci->hcca->done_head) & 0xfffffff0; - ohci->hcca->done_head = 0; - - while (td_list_hc) { - td_list = (td_t *)td_list_hc; - - if (TD_CC_GET (m32_swap (td_list->hwINFO))) { - lurb_priv = &urb_priv; - dbg(" USB-error/status: %x : %p", - TD_CC_GET (m32_swap (td_list->hwINFO)), td_list); - if (td_list->ed->hwHeadP & m32_swap (0x1)) { - if (lurb_priv && ((td_list->index + 1) < lurb_priv->length)) { - td_list->ed->hwHeadP = - (lurb_priv->td[lurb_priv->length - 1]->hwNextTD & m32_swap (0xfffffff0)) | - (td_list->ed->hwHeadP & m32_swap (0x2)); - lurb_priv->td_cnt += lurb_priv->length - td_list->index - 1; - } else - td_list->ed->hwHeadP &= m32_swap (0xfffffff2); - } - } - - td_list->next_dl_td = td_rev; - td_rev = td_list; - td_list_hc = m32_swap (td_list->hwNextTD) & 0xfffffff0; - } - return td_list; -} - -/*-------------------------------------------------------------------------*/ - -/* td done list */ -static int dl_done_list (ohci_t *ohci, td_t *td_list) -{ - td_t *td_list_next = NULL; - ed_t *ed; - int cc = 0; - int stat = 0; - /* urb_t *urb; */ - urb_priv_t *lurb_priv; - __u32 tdINFO, edHeadP, edTailP; - - while (td_list) { - td_list_next = td_list->next_dl_td; - - lurb_priv = &urb_priv; - tdINFO = m32_swap (td_list->hwINFO); - - ed = td_list->ed; - - dl_transfer_length(td_list); - - /* error code of transfer */ - cc = TD_CC_GET (tdINFO); - if (cc != 0) { - dbg("ConditionCode %#x", cc); - stat = cc_to_error[cc]; - } - - if (ed->state != ED_NEW) { - edHeadP = m32_swap (ed->hwHeadP) & 0xfffffff0; - edTailP = m32_swap (ed->hwTailP); - - /* unlink eds if they are not busy */ - if ((edHeadP == edTailP) && (ed->state == ED_OPER)) - ep_unlink (ohci, ed); - } - - td_list = td_list_next; - } - return stat; -} - -/*-------------------------------------------------------------------------* - * Virtual Root Hub - *-------------------------------------------------------------------------*/ - -/* Device descriptor */ -static __u8 root_hub_dev_des[] = -{ - 0x12, /* __u8 bLength; */ - 0x01, /* __u8 bDescriptorType; Device */ - 0x10, /* __u16 bcdUSB; v1.1 */ - 0x01, - 0x09, /* __u8 bDeviceClass; HUB_CLASSCODE */ - 0x00, /* __u8 bDeviceSubClass; */ - 0x00, /* __u8 bDeviceProtocol; */ - 0x08, /* __u8 bMaxPacketSize0; 8 Bytes */ - 0x00, /* __u16 idVendor; */ - 0x00, - 0x00, /* __u16 idProduct; */ - 0x00, - 0x00, /* __u16 bcdDevice; */ - 0x00, - 0x00, /* __u8 iManufacturer; */ - 0x01, /* __u8 iProduct; */ - 0x00, /* __u8 iSerialNumber; */ - 0x01 /* __u8 bNumConfigurations; */ -}; - - -/* Configuration descriptor */ -static __u8 root_hub_config_des[] = -{ - 0x09, /* __u8 bLength; */ - 0x02, /* __u8 bDescriptorType; Configuration */ - 0x19, /* __u16 wTotalLength; */ - 0x00, - 0x01, /* __u8 bNumInterfaces; */ - 0x01, /* __u8 bConfigurationValue; */ - 0x00, /* __u8 iConfiguration; */ - 0x40, /* __u8 bmAttributes; - Bit 7: Bus-powered, 6: Self-powered, 5 Remote-wakwup, 4..0: resvd */ - 0x00, /* __u8 MaxPower; */ - - /* interface */ - 0x09, /* __u8 if_bLength; */ - 0x04, /* __u8 if_bDescriptorType; Interface */ - 0x00, /* __u8 if_bInterfaceNumber; */ - 0x00, /* __u8 if_bAlternateSetting; */ - 0x01, /* __u8 if_bNumEndpoints; */ - 0x09, /* __u8 if_bInterfaceClass; HUB_CLASSCODE */ - 0x00, /* __u8 if_bInterfaceSubClass; */ - 0x00, /* __u8 if_bInterfaceProtocol; */ - 0x00, /* __u8 if_iInterface; */ - - /* endpoint */ - 0x07, /* __u8 ep_bLength; */ - 0x05, /* __u8 ep_bDescriptorType; Endpoint */ - 0x81, /* __u8 ep_bEndpointAddress; IN Endpoint 1 */ - 0x03, /* __u8 ep_bmAttributes; Interrupt */ - 0x02, /* __u16 ep_wMaxPacketSize; ((MAX_ROOT_PORTS + 1) / 8 */ - 0x00, - 0xff /* __u8 ep_bInterval; 255 ms */ -}; - -static unsigned char root_hub_str_index0[] = -{ - 0x04, /* __u8 bLength; */ - 0x03, /* __u8 bDescriptorType; String-descriptor */ - 0x09, /* __u8 lang ID */ - 0x04, /* __u8 lang ID */ -}; - -static unsigned char root_hub_str_index1[] = -{ - 28, /* __u8 bLength; */ - 0x03, /* __u8 bDescriptorType; String-descriptor */ - 'O', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'H', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'C', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'I', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - ' ', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'R', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'o', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'o', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 't', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - ' ', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'H', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'u', /* __u8 Unicode */ - 0, /* __u8 Unicode */ - 'b', /* __u8 Unicode */ - 0, /* __u8 Unicode */ -}; - -/* Hub class-specific descriptor is constructed dynamically */ - - -/*-------------------------------------------------------------------------*/ - -#define OK(x) len = (x); break -#ifdef DEBUG -#define WR_RH_STAT(x) {info("WR:status %#8x", (x));writel((x), &gohci.regs->roothub.status);} -#define WR_RH_PORTSTAT(x) {info("WR:portstatus[%d] %#8x", wIndex-1, (x));writel((x), &gohci.regs->roothub.portstatus[wIndex-1]);} -#else -#define WR_RH_STAT(x) writel((x), &gohci.regs->roothub.status) -#define WR_RH_PORTSTAT(x) writel((x), &gohci.regs->roothub.portstatus[wIndex-1]) -#endif -#define RD_RH_STAT roothub_status(&gohci) -#define RD_RH_PORTSTAT roothub_portstatus(&gohci,wIndex-1) - -/* request to virtual root hub */ - -int rh_check_port_status(ohci_t *controller) -{ - __u32 temp, ndp, i; - int res; - - res = -1; - temp = roothub_a (controller); - ndp = (temp & RH_A_NDP); - for (i = 0; i < ndp; i++) { - temp = roothub_portstatus (controller, i); - /* check for a device disconnect */ - if (((temp & (RH_PS_PESC | RH_PS_CSC)) == - (RH_PS_PESC | RH_PS_CSC)) && - ((temp & RH_PS_CCS) == 0)) { - res = i; - break; - } - } - return res; -} - -static int ohci_submit_rh_msg(struct usb_device *dev, unsigned long pipe, - void *buffer, int transfer_len, struct devrequest *cmd) -{ - void * data = buffer; - int leni = transfer_len; - int len = 0; - int stat = 0; - __u32 datab[4]; - __u8 *data_buf = (__u8 *)datab; - __u16 bmRType_bReq; - __u16 wValue; - __u16 wIndex; - __u16 wLength; - -#ifdef DEBUG -urb_priv.actual_length = 0; -pkt_print(dev, pipe, buffer, transfer_len, cmd, "SUB(rh)", usb_pipein(pipe)); -#else - wait_ms(1); -#endif - if ((pipe & PIPE_INTERRUPT) == PIPE_INTERRUPT) { - info("Root-Hub submit IRQ: NOT implemented"); - return 0; - } - - bmRType_bReq = cmd->requesttype | (cmd->request << 8); - wValue = m16_swap (cmd->value); - wIndex = m16_swap (cmd->index); - wLength = m16_swap (cmd->length); - - info("Root-Hub: adr: %2x cmd(%1x): %08x %04x %04x %04x", - dev->devnum, 8, bmRType_bReq, wValue, wIndex, wLength); - - switch (bmRType_bReq) { - /* Request Destination: - without flags: Device, - RH_INTERFACE: interface, - RH_ENDPOINT: endpoint, - RH_CLASS means HUB here, - RH_OTHER | RH_CLASS almost ever means HUB_PORT here - */ - - case RH_GET_STATUS: - *(__u16 *) data_buf = m16_swap (1); OK (2); - case RH_GET_STATUS | RH_INTERFACE: - *(__u16 *) data_buf = m16_swap (0); OK (2); - case RH_GET_STATUS | RH_ENDPOINT: - *(__u16 *) data_buf = m16_swap (0); OK (2); - case RH_GET_STATUS | RH_CLASS: - *(__u32 *) data_buf = m32_swap ( - RD_RH_STAT & ~(RH_HS_CRWE | RH_HS_DRWE)); - OK (4); - case RH_GET_STATUS | RH_OTHER | RH_CLASS: - *(__u32 *) data_buf = m32_swap (RD_RH_PORTSTAT); OK (4); - - case RH_CLEAR_FEATURE | RH_ENDPOINT: - switch (wValue) { - case (RH_ENDPOINT_STALL): OK (0); - } - break; - - case RH_CLEAR_FEATURE | RH_CLASS: - switch (wValue) { - case RH_C_HUB_LOCAL_POWER: - OK(0); - case (RH_C_HUB_OVER_CURRENT): - WR_RH_STAT(RH_HS_OCIC); OK (0); - } - break; - - case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS: - switch (wValue) { - case (RH_PORT_ENABLE): - WR_RH_PORTSTAT (RH_PS_CCS ); OK (0); - case (RH_PORT_SUSPEND): - WR_RH_PORTSTAT (RH_PS_POCI); OK (0); - case (RH_PORT_POWER): - WR_RH_PORTSTAT (RH_PS_LSDA); OK (0); - case (RH_C_PORT_CONNECTION): - WR_RH_PORTSTAT (RH_PS_CSC ); OK (0); - case (RH_C_PORT_ENABLE): - WR_RH_PORTSTAT (RH_PS_PESC); OK (0); - case (RH_C_PORT_SUSPEND): - WR_RH_PORTSTAT (RH_PS_PSSC); OK (0); - case (RH_C_PORT_OVER_CURRENT): - WR_RH_PORTSTAT (RH_PS_OCIC); OK (0); - case (RH_C_PORT_RESET): - WR_RH_PORTSTAT (RH_PS_PRSC); OK (0); - } - break; - - case RH_SET_FEATURE | RH_OTHER | RH_CLASS: - switch (wValue) { - case (RH_PORT_SUSPEND): - WR_RH_PORTSTAT (RH_PS_PSS ); OK (0); - case (RH_PORT_RESET): /* BUG IN HUP CODE *********/ - if (RD_RH_PORTSTAT & RH_PS_CCS) - WR_RH_PORTSTAT (RH_PS_PRS); - OK (0); - case (RH_PORT_POWER): - WR_RH_PORTSTAT (RH_PS_PPS ); OK (0); - case (RH_PORT_ENABLE): /* BUG IN HUP CODE *********/ - if (RD_RH_PORTSTAT & RH_PS_CCS) - WR_RH_PORTSTAT (RH_PS_PES ); - OK (0); - } - break; - - case RH_SET_ADDRESS: gohci.rh.devnum = wValue; OK(0); - - case RH_GET_DESCRIPTOR: - switch ((wValue & 0xff00) >> 8) { - case (0x01): /* device descriptor */ - len = min_t(unsigned int, - leni, - min_t(unsigned int, - sizeof (root_hub_dev_des), - wLength)); - data_buf = root_hub_dev_des; OK(len); - case (0x02): /* configuration descriptor */ - len = min_t(unsigned int, - leni, - min_t(unsigned int, - sizeof (root_hub_config_des), - wLength)); - data_buf = root_hub_config_des; OK(len); - case (0x03): /* string descriptors */ - if(wValue==0x0300) { - len = min_t(unsigned int, - leni, - min_t(unsigned int, - sizeof (root_hub_str_index0), - wLength)); - data_buf = root_hub_str_index0; - OK(len); - } - if(wValue==0x0301) { - len = min_t(unsigned int, - leni, - min_t(unsigned int, - sizeof (root_hub_str_index1), - wLength)); - data_buf = root_hub_str_index1; - OK(len); - } - default: - stat = USB_ST_STALLED; - } - break; - - case RH_GET_DESCRIPTOR | RH_CLASS: - { - __u32 temp = roothub_a (&gohci); - - data_buf [0] = 9; /* min length; */ - data_buf [1] = 0x29; - data_buf [2] = temp & RH_A_NDP; - data_buf [3] = 0; - if (temp & RH_A_PSM) /* per-port power switching? */ - data_buf [3] |= 0x1; - if (temp & RH_A_NOCP) /* no overcurrent reporting? */ - data_buf [3] |= 0x10; - else if (temp & RH_A_OCPM) /* per-port overcurrent reporting? */ - data_buf [3] |= 0x8; - - /* corresponds to data_buf[4-7] */ - datab [1] = 0; - data_buf [5] = (temp & RH_A_POTPGT) >> 24; - temp = roothub_b (&gohci); - data_buf [7] = temp & RH_B_DR; - if (data_buf [2] < 7) { - data_buf [8] = 0xff; - } else { - data_buf [0] += 2; - data_buf [8] = (temp & RH_B_DR) >> 8; - data_buf [10] = data_buf [9] = 0xff; - } - - len = min_t(unsigned int, leni, - min_t(unsigned int, data_buf [0], wLength)); - OK (len); - } - - case RH_GET_CONFIGURATION: *(__u8 *) data_buf = 0x01; OK (1); - - case RH_SET_CONFIGURATION: WR_RH_STAT (0x10000); OK (0); - - default: - dbg ("unsupported root hub command"); - stat = USB_ST_STALLED; - } - -#ifdef DEBUG - ohci_dump_roothub (&gohci, 1); -#else - wait_ms(1); -#endif - - len = min_t(int, len, leni); - if (data != data_buf) - memcpy (data, data_buf, len); - dev->act_len = len; - dev->status = stat; - -#ifdef DEBUG - if (transfer_len) - urb_priv.actual_length = transfer_len; - pkt_print(dev, pipe, buffer, transfer_len, cmd, "RET(rh)", 0/*usb_pipein(pipe)*/); -#else - wait_ms(1); -#endif - - return stat; -} - -/*-------------------------------------------------------------------------*/ - -/* common code for handling submit messages - used for all but root hub */ -/* accesses. */ -int submit_common_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len, struct devrequest *setup, int interval) -{ - int stat = 0; - int maxsize = usb_maxpacket(dev, pipe); - int timeout; - - /* device pulled? Shortcut the action. */ - if (devgone == dev) { - dev->status = USB_ST_CRC_ERR; - return 0; - } - -#ifdef DEBUG - urb_priv.actual_length = 0; - pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe)); -#else - wait_ms(1); -#endif - if (!maxsize) { - err("submit_common_message: pipesize for pipe %lx is zero", - pipe); - return -1; - } - - if (sohci_submit_job(dev, pipe, buffer, transfer_len, setup, interval) < 0) { - err("sohci_submit_job failed"); - return -1; - } - - wait_ms(10); - /* ohci_dump_status(&gohci); */ - - /* allow more time for a BULK device to react - some are slow */ -#define BULK_TO 5000 /* timeout in milliseconds */ - if (usb_pipetype (pipe) == PIPE_BULK) - timeout = BULK_TO; - else - timeout = 100; - - /* wait for it to complete */ - for (;;) { - /* check whether the controller is done */ - stat = hc_interrupt(); - if (stat < 0) { - stat = USB_ST_CRC_ERR; - break; - } - if (stat >= 0 && stat != 0xff) { - /* 0xff is returned for an SF-interrupt */ - break; - } - if (--timeout) { - wait_ms(1); - } else { - err("CTL:TIMEOUT "); - stat = USB_ST_CRC_ERR; - break; - } - } - /* we got an Root Hub Status Change interrupt */ - if (got_rhsc) { -#ifdef DEBUG - ohci_dump_roothub (&gohci, 1); -#endif - got_rhsc = 0; - /* abuse timeout */ - timeout = rh_check_port_status(&gohci); - if (timeout >= 0) { -#if 0 /* this does nothing useful, but leave it here in case that changes */ - /* the called routine adds 1 to the passed value */ - usb_hub_port_connect_change(gohci.rh.dev, timeout - 1); -#endif - /* - * XXX - * This is potentially dangerous because it assumes - * that only one device is ever plugged in! - */ - devgone = dev; - } - } - - dev->status = stat; - dev->act_len = transfer_len; - -#ifdef DEBUG - pkt_print(dev, pipe, buffer, transfer_len, setup, "RET(ctlr)", usb_pipein(pipe)); -#else - wait_ms(1); -#endif - - /* free TDs in urb_priv */ - urb_free_priv (&urb_priv); - return 0; -} - -/* submit routines called from usb.c */ -int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len) -{ - info("submit_bulk_msg"); - return submit_common_msg(dev, pipe, buffer, transfer_len, NULL, 0); -} - -int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len, struct devrequest *setup) -{ - int maxsize = usb_maxpacket(dev, pipe); - - info("submit_control_msg"); -#ifdef DEBUG - urb_priv.actual_length = 0; - pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe)); -#else - wait_ms(1); -#endif - if (!maxsize) { - err("submit_control_message: pipesize for pipe %lx is zero", - pipe); - return -1; - } - if (((pipe >> 8) & 0x7f) == gohci.rh.devnum) { - gohci.rh.dev = dev; - /* root hub - redirect */ - return ohci_submit_rh_msg(dev, pipe, buffer, transfer_len, - setup); - } - - return submit_common_msg(dev, pipe, buffer, transfer_len, setup, 0); -} - -int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer, - int transfer_len, int interval) -{ - info("submit_int_msg"); - return -1; -} - -/*-------------------------------------------------------------------------* - * HC functions - *-------------------------------------------------------------------------*/ - -/* reset the HC and BUS */ - -static int hc_reset (ohci_t *ohci) -{ - int timeout = 30; - int smm_timeout = 50; /* 0,5 sec */ - - if (readl (&ohci->regs->control) & OHCI_CTRL_IR) { /* SMM owns the HC */ - writel (OHCI_OCR, &ohci->regs->cmdstatus); /* request ownership */ - info("USB HC TakeOver from SMM"); - while (readl (&ohci->regs->control) & OHCI_CTRL_IR) { - wait_ms (10); - if (--smm_timeout == 0) { - err("USB HC TakeOver failed!"); - return -1; - } - } - } - - /* Disable HC interrupts */ - writel (OHCI_INTR_MIE, &ohci->regs->intrdisable); - - dbg("USB HC reset_hc usb-%s: ctrl = 0x%X ;", - ohci->slot_name, - readl (&ohci->regs->control)); - - /* Reset USB (needed by some controllers) */ - writel (0, &ohci->regs->control); - - /* HC Reset requires max 10 us delay */ - writel (OHCI_HCR, &ohci->regs->cmdstatus); - while ((readl (&ohci->regs->cmdstatus) & OHCI_HCR) != 0) { - if (--timeout == 0) { - err("USB HC reset timed out!"); - return -1; - } - udelay (1); - } - return 0; -} - -/*-------------------------------------------------------------------------*/ - -/* Start an OHCI controller, set the BUS operational - * enable interrupts - * connect the virtual root hub */ - -static int hc_start (ohci_t * ohci) -{ - __u32 mask; - unsigned int fminterval; - - ohci->disabled = 1; - - /* Tell the controller where the control and bulk lists are - * The lists are empty now. */ - - writel (0, &ohci->regs->ed_controlhead); - writel (0, &ohci->regs->ed_bulkhead); - - writel ((__u32)ohci->hcca, &ohci->regs->hcca); /* a reset clears this */ - - fminterval = 0x2edf; - writel ((fminterval * 9) / 10, &ohci->regs->periodicstart); - fminterval |= ((((fminterval - 210) * 6) / 7) << 16); - writel (fminterval, &ohci->regs->fminterval); - writel (0x628, &ohci->regs->lsthresh); - - /* start controller operations */ - ohci->hc_control = OHCI_CONTROL_INIT | OHCI_USB_OPER; - ohci->disabled = 0; - writel (ohci->hc_control, &ohci->regs->control); - - /* disable all interrupts */ - mask = (OHCI_INTR_SO | OHCI_INTR_WDH | OHCI_INTR_SF | OHCI_INTR_RD | - OHCI_INTR_UE | OHCI_INTR_FNO | OHCI_INTR_RHSC | - OHCI_INTR_OC | OHCI_INTR_MIE); - writel (mask, &ohci->regs->intrdisable); - /* clear all interrupts */ - mask &= ~OHCI_INTR_MIE; - writel (mask, &ohci->regs->intrstatus); - /* Choose the interrupts we care about now - but w/o MIE */ - mask = OHCI_INTR_RHSC | OHCI_INTR_UE | OHCI_INTR_WDH | OHCI_INTR_SO; - writel (mask, &ohci->regs->intrenable); - -#ifdef OHCI_USE_NPS - /* required for AMD-756 and some Mac platforms */ - writel ((roothub_a (ohci) | RH_A_NPS) & ~RH_A_PSM, - &ohci->regs->roothub.a); - writel (RH_HS_LPSC, &ohci->regs->roothub.status); -#endif /* OHCI_USE_NPS */ - -#define mdelay(n) ({unsigned long msec=(n); while (msec--) udelay(1000);}) - /* POTPGT delay is bits 24-31, in 2 ms units. */ - mdelay ((roothub_a (ohci) >> 23) & 0x1fe); - - /* connect the virtual root hub */ - ohci->rh.devnum = 0; - - return 0; -} - -/*-------------------------------------------------------------------------*/ - -/* an interrupt happens */ - -static int -hc_interrupt (void) -{ - ohci_t *ohci = &gohci; - struct ohci_regs *regs = ohci->regs; - int ints; - int stat = -1; - - if ((ohci->hcca->done_head != 0) && !(m32_swap (ohci->hcca->done_head) & 0x01)) { - ints = OHCI_INTR_WDH; - } else { - ints = readl (®s->intrstatus); - } - - /* dbg("Interrupt: %x frame: %x", ints, le16_to_cpu (ohci->hcca->frame_no)); */ - - if (ints & OHCI_INTR_RHSC) { - got_rhsc = 1; - } - - if (ints & OHCI_INTR_UE) { - ohci->disabled++; - err ("OHCI Unrecoverable Error, controller usb-%s disabled", - ohci->slot_name); - /* e.g. due to PCI Master/Target Abort */ - -#ifdef DEBUG - ohci_dump (ohci, 1); -#else - wait_ms(1); -#endif - /* FIXME: be optimistic, hope that bug won't repeat often. */ - /* Make some non-interrupt context restart the controller. */ - /* Count and limit the retries though; either hardware or */ - /* software errors can go forever... */ - hc_reset (ohci); - return -1; - } - - if (ints & OHCI_INTR_WDH) { - wait_ms(1); - writel (OHCI_INTR_WDH, ®s->intrdisable); - stat = dl_done_list (&gohci, dl_reverse_done_list (&gohci)); - writel (OHCI_INTR_WDH, ®s->intrenable); - } - - if (ints & OHCI_INTR_SO) { - dbg("USB Schedule overrun\n"); - writel (OHCI_INTR_SO, ®s->intrenable); - stat = -1; - } - - /* FIXME: this assumes SOF (1/ms) interrupts don't get lost... */ - if (ints & OHCI_INTR_SF) { - unsigned int frame = m16_swap (ohci->hcca->frame_no) & 1; - wait_ms(1); - writel (OHCI_INTR_SF, ®s->intrdisable); - if (ohci->ed_rm_list[frame] != NULL) - writel (OHCI_INTR_SF, ®s->intrenable); - stat = 0xff; - } - - writel (ints, ®s->intrstatus); - return stat; -} - -/*-------------------------------------------------------------------------*/ - -/*-------------------------------------------------------------------------*/ - -/* De-allocate all resources.. */ - -static void hc_release_ohci (ohci_t *ohci) -{ - dbg ("USB HC release ohci usb-%s", ohci->slot_name); - - if (!ohci->disabled) - hc_reset (ohci); -} - -/*-------------------------------------------------------------------------*/ - -/* - * low level initalisation routine, called from usb.c - */ -static char ohci_inited = 0; - -int usb_lowlevel_init(void) -{ - S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); - S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO(); - - /* - * Set the 48 MHz UPLL clocking. Values are taken from - * "PLL value selection guide", 6-23, s3c2400_UM.pdf. - */ - clk_power->UPLLCON = ((40 << 12) + (1 << 4) + 2); - gpio->MISCCR |= 0x8; /* 1 = use pads related USB for USB host */ - - /* - * Enable USB host clock. - */ - clk_power->CLKCON |= (1 << 4); - - memset (&gohci, 0, sizeof (ohci_t)); - memset (&urb_priv, 0, sizeof (urb_priv_t)); - - /* align the storage */ - if ((__u32)&ghcca[0] & 0xff) { - err("HCCA not aligned!!"); - return -1; - } - phcca = &ghcca[0]; - info("aligned ghcca %p", phcca); - memset(&ohci_dev, 0, sizeof(struct ohci_device)); - if ((__u32)&ohci_dev.ed[0] & 0x7) { - err("EDs not aligned!!"); - return -1; - } - memset(gtd, 0, sizeof(td_t) * (NUM_TD + 1)); - if ((__u32)gtd & 0x7) { - err("TDs not aligned!!"); - return -1; - } - ptd = gtd; - gohci.hcca = phcca; - memset (phcca, 0, sizeof (struct ohci_hcca)); - - gohci.disabled = 1; - gohci.sleeping = 0; - gohci.irq = -1; - gohci.regs = (struct ohci_regs *)S3C24X0_USB_HOST_BASE; - - gohci.flags = 0; - gohci.slot_name = "s3c2400"; - - if (hc_reset (&gohci) < 0) { - hc_release_ohci (&gohci); - /* Initialization failed */ - clk_power->CLKCON &= ~(1 << 4); - return -1; - } - - /* FIXME this is a second HC reset; why?? */ - writel (gohci.hc_control = OHCI_USB_RESET, &gohci.regs->control); - wait_ms (10); - - if (hc_start (&gohci) < 0) { - err ("can't start usb-%s", gohci.slot_name); - hc_release_ohci (&gohci); - /* Initialization failed */ - clk_power->CLKCON &= ~(1 << 4); - return -1; - } - -#ifdef DEBUG - ohci_dump (&gohci, 1); -#else - wait_ms(1); -#endif - ohci_inited = 1; - return 0; -} - -int usb_lowlevel_stop(void) -{ - S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER(); - - /* this gets called really early - before the controller has */ - /* even been initialized! */ - if (!ohci_inited) - return 0; - /* TODO release any interrupts, etc. */ - /* call hc_release_ohci() here ? */ - hc_reset (&gohci); - /* may not want to do this */ - clk_power->CLKCON &= ~(1 << 4); - return 0; -} - -#endif /* CONFIG_USB_OHCI */ diff --git a/cpu/arm920t/usb_ohci.h b/cpu/arm920t/usb_ohci.h deleted file mode 100644 index fab0e65..0000000 --- a/cpu/arm920t/usb_ohci.h +++ /dev/null @@ -1,419 +0,0 @@ -/* - * URB OHCI HCD (Host Controller Driver) for USB. - * - * (C) Copyright 1999 Roman Weissgaerber - * (C) Copyright 2000-2001 David Brownell - * - * usb-ohci.h - */ - - -static int cc_to_error[16] = { - -/* mapping of the OHCI CC status to error codes */ - /* No Error */ 0, - /* CRC Error */ USB_ST_CRC_ERR, - /* Bit Stuff */ USB_ST_BIT_ERR, - /* Data Togg */ USB_ST_CRC_ERR, - /* Stall */ USB_ST_STALLED, - /* DevNotResp */ -1, - /* PIDCheck */ USB_ST_BIT_ERR, - /* UnExpPID */ USB_ST_BIT_ERR, - /* DataOver */ USB_ST_BUF_ERR, - /* DataUnder */ USB_ST_BUF_ERR, - /* reservd */ -1, - /* reservd */ -1, - /* BufferOver */ USB_ST_BUF_ERR, - /* BuffUnder */ USB_ST_BUF_ERR, - /* Not Access */ -1, - /* Not Access */ -1 -}; - -/* ED States */ - -#define ED_NEW 0x00 -#define ED_UNLINK 0x01 -#define ED_OPER 0x02 -#define ED_DEL 0x04 -#define ED_URB_DEL 0x08 - -/* usb_ohci_ed */ -struct ed { - __u32 hwINFO; - __u32 hwTailP; - __u32 hwHeadP; - __u32 hwNextED; - - struct ed *ed_prev; - __u8 int_period; - __u8 int_branch; - __u8 int_load; - __u8 int_interval; - __u8 state; - __u8 type; - __u16 last_iso; - struct ed *ed_rm_list; - - struct usb_device *usb_dev; - __u32 unused[3]; -} __attribute((aligned(16))); -typedef struct ed ed_t; - - -/* TD info field */ -#define TD_CC 0xf0000000 -#define TD_CC_GET(td_p) ((td_p >>28) & 0x0f) -#define TD_CC_SET(td_p, cc) (td_p) = ((td_p) & 0x0fffffff) | (((cc) & 0x0f) << 28) -#define TD_EC 0x0C000000 -#define TD_T 0x03000000 -#define TD_T_DATA0 0x02000000 -#define TD_T_DATA1 0x03000000 -#define TD_T_TOGGLE 0x00000000 -#define TD_R 0x00040000 -#define TD_DI 0x00E00000 -#define TD_DI_SET(X) (((X) & 0x07)<< 21) -#define TD_DP 0x00180000 -#define TD_DP_SETUP 0x00000000 -#define TD_DP_IN 0x00100000 -#define TD_DP_OUT 0x00080000 - -#define TD_ISO 0x00010000 -#define TD_DEL 0x00020000 - -/* CC Codes */ -#define TD_CC_NOERROR 0x00 -#define TD_CC_CRC 0x01 -#define TD_CC_BITSTUFFING 0x02 -#define TD_CC_DATATOGGLEM 0x03 -#define TD_CC_STALL 0x04 -#define TD_DEVNOTRESP 0x05 -#define TD_PIDCHECKFAIL 0x06 -#define TD_UNEXPECTEDPID 0x07 -#define TD_DATAOVERRUN 0x08 -#define TD_DATAUNDERRUN 0x09 -#define TD_BUFFEROVERRUN 0x0C -#define TD_BUFFERUNDERRUN 0x0D -#define TD_NOTACCESSED 0x0F - - -#define MAXPSW 1 - -struct td { - __u32 hwINFO; - __u32 hwCBP; /* Current Buffer Pointer */ - __u32 hwNextTD; /* Next TD Pointer */ - __u32 hwBE; /* Memory Buffer End Pointer */ - - __u16 hwPSW[MAXPSW]; - __u8 unused; - __u8 index; - struct ed *ed; - struct td *next_dl_td; - struct usb_device *usb_dev; - int transfer_len; - __u32 data; - - __u32 unused2[2]; -} __attribute((aligned(32))); -typedef struct td td_t; - -#define OHCI_ED_SKIP (1 << 14) - -/* - * The HCCA (Host Controller Communications Area) is a 256 byte - * structure defined in the OHCI spec. that the host controller is - * told the base address of. It must be 256-byte aligned. - */ - -#define NUM_INTS 32 /* part of the OHCI standard */ -struct ohci_hcca { - __u32 int_table[NUM_INTS]; /* Interrupt ED table */ - __u16 frame_no; /* current frame number */ - __u16 pad1; /* set to 0 on each frame_no change */ - __u32 done_head; /* info returned for an interrupt */ - u8 reserved_for_hc[116]; -} __attribute((aligned(256))); - - -/* - * Maximum number of root hub ports. - */ -#define MAX_ROOT_PORTS 15 /* maximum OHCI root hub ports */ - -/* - * This is the structure of the OHCI controller's memory mapped I/O - * region. This is Memory Mapped I/O. You must use the readl() and - * writel() macros defined in asm/io.h to access these!! - */ -struct ohci_regs { - /* control and status registers */ - __u32 revision; - __u32 control; - __u32 cmdstatus; - __u32 intrstatus; - __u32 intrenable; - __u32 intrdisable; - /* memory pointers */ - __u32 hcca; - __u32 ed_periodcurrent; - __u32 ed_controlhead; - __u32 ed_controlcurrent; - __u32 ed_bulkhead; - __u32 ed_bulkcurrent; - __u32 donehead; - /* frame counters */ - __u32 fminterval; - __u32 fmremaining; - __u32 fmnumber; - __u32 periodicstart; - __u32 lsthresh; - /* Root hub ports */ - struct ohci_roothub_regs { - __u32 a; - __u32 b; - __u32 status; - __u32 portstatus[MAX_ROOT_PORTS]; - } roothub; -} __attribute((aligned(32))); - - -/* OHCI CONTROL AND STATUS REGISTER MASKS */ - -/* - * HcControl (control) register masks - */ -#define OHCI_CTRL_CBSR (3 << 0) /* control/bulk service ratio */ -#define OHCI_CTRL_PLE (1 << 2) /* periodic list enable */ -#define OHCI_CTRL_IE (1 << 3) /* isochronous enable */ -#define OHCI_CTRL_CLE (1 << 4) /* control list enable */ -#define OHCI_CTRL_BLE (1 << 5) /* bulk list enable */ -#define OHCI_CTRL_HCFS (3 << 6) /* host controller functional state */ -#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */ -#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */ -#define OHCI_CTRL_RWE (1 << 10) /* remote wakeup enable */ - -/* pre-shifted values for HCFS */ -# define OHCI_USB_RESET (0 << 6) -# define OHCI_USB_RESUME (1 << 6) -# define OHCI_USB_OPER (2 << 6) -# define OHCI_USB_SUSPEND (3 << 6) - -/* - * HcCommandStatus (cmdstatus) register masks - */ -#define OHCI_HCR (1 << 0) /* host controller reset */ -#define OHCI_CLF (1 << 1) /* control list filled */ -#define OHCI_BLF (1 << 2) /* bulk list filled */ -#define OHCI_OCR (1 << 3) /* ownership change request */ -#define OHCI_SOC (3 << 16) /* scheduling overrun count */ - -/* - * masks used with interrupt registers: - * HcInterruptStatus (intrstatus) - * HcInterruptEnable (intrenable) - * HcInterruptDisable (intrdisable) - */ -#define OHCI_INTR_SO (1 << 0) /* scheduling overrun */ -#define OHCI_INTR_WDH (1 << 1) /* writeback of done_head */ -#define OHCI_INTR_SF (1 << 2) /* start frame */ -#define OHCI_INTR_RD (1 << 3) /* resume detect */ -#define OHCI_INTR_UE (1 << 4) /* unrecoverable error */ -#define OHCI_INTR_FNO (1 << 5) /* frame number overflow */ -#define OHCI_INTR_RHSC (1 << 6) /* root hub status change */ -#define OHCI_INTR_OC (1 << 30) /* ownership change */ -#define OHCI_INTR_MIE (1 << 31) /* master interrupt enable */ - - -/* Virtual Root HUB */ -struct virt_root_hub { - int devnum; /* Address of Root Hub endpoint */ - void *dev; /* was urb */ - void *int_addr; - int send; - int interval; -}; - -/* USB HUB CONSTANTS (not OHCI-specific; see hub.h) */ - -/* destination of request */ -#define RH_INTERFACE 0x01 -#define RH_ENDPOINT 0x02 -#define RH_OTHER 0x03 - -#define RH_CLASS 0x20 -#define RH_VENDOR 0x40 - -/* Requests: bRequest << 8 | bmRequestType */ -#define RH_GET_STATUS 0x0080 -#define RH_CLEAR_FEATURE 0x0100 -#define RH_SET_FEATURE 0x0300 -#define RH_SET_ADDRESS 0x0500 -#define RH_GET_DESCRIPTOR 0x0680 -#define RH_SET_DESCRIPTOR 0x0700 -#define RH_GET_CONFIGURATION 0x0880 -#define RH_SET_CONFIGURATION 0x0900 -#define RH_GET_STATE 0x0280 -#define RH_GET_INTERFACE 0x0A80 -#define RH_SET_INTERFACE 0x0B00 -#define RH_SYNC_FRAME 0x0C80 -/* Our Vendor Specific Request */ -#define RH_SET_EP 0x2000 - - -/* Hub port features */ -#define RH_PORT_CONNECTION 0x00 -#define RH_PORT_ENABLE 0x01 -#define RH_PORT_SUSPEND 0x02 -#define RH_PORT_OVER_CURRENT 0x03 -#define RH_PORT_RESET 0x04 -#define RH_PORT_POWER 0x08 -#define RH_PORT_LOW_SPEED 0x09 - -#define RH_C_PORT_CONNECTION 0x10 -#define RH_C_PORT_ENABLE 0x11 -#define RH_C_PORT_SUSPEND 0x12 -#define RH_C_PORT_OVER_CURRENT 0x13 -#define RH_C_PORT_RESET 0x14 - -/* Hub features */ -#define RH_C_HUB_LOCAL_POWER 0x00 -#define RH_C_HUB_OVER_CURRENT 0x01 - -#define RH_DEVICE_REMOTE_WAKEUP 0x00 -#define RH_ENDPOINT_STALL 0x01 - -#define RH_ACK 0x01 -#define RH_REQ_ERR -1 -#define RH_NACK 0x00 - - -/* OHCI ROOT HUB REGISTER MASKS */ - -/* roothub.portstatus [i] bits */ -#define RH_PS_CCS 0x00000001 /* current connect status */ -#define RH_PS_PES 0x00000002 /* port enable status*/ -#define RH_PS_PSS 0x00000004 /* port suspend status */ -#define RH_PS_POCI 0x00000008 /* port over current indicator */ -#define RH_PS_PRS 0x00000010 /* port reset status */ -#define RH_PS_PPS 0x00000100 /* port power status */ -#define RH_PS_LSDA 0x00000200 /* low speed device attached */ -#define RH_PS_CSC 0x00010000 /* connect status change */ -#define RH_PS_PESC 0x00020000 /* port enable status change */ -#define RH_PS_PSSC 0x00040000 /* port suspend status change */ -#define RH_PS_OCIC 0x00080000 /* over current indicator change */ -#define RH_PS_PRSC 0x00100000 /* port reset status change */ - -/* roothub.status bits */ -#define RH_HS_LPS 0x00000001 /* local power status */ -#define RH_HS_OCI 0x00000002 /* over current indicator */ -#define RH_HS_DRWE 0x00008000 /* device remote wakeup enable */ -#define RH_HS_LPSC 0x00010000 /* local power status change */ -#define RH_HS_OCIC 0x00020000 /* over current indicator change */ -#define RH_HS_CRWE 0x80000000 /* clear remote wakeup enable */ - -/* roothub.b masks */ -#define RH_B_DR 0x0000ffff /* device removable flags */ -#define RH_B_PPCM 0xffff0000 /* port power control mask */ - -/* roothub.a masks */ -#define RH_A_NDP (0xff << 0) /* number of downstream ports */ -#define RH_A_PSM (1 << 8) /* power switching mode */ -#define RH_A_NPS (1 << 9) /* no power switching */ -#define RH_A_DT (1 << 10) /* device type (mbz) */ -#define RH_A_OCPM (1 << 11) /* over current protection mode */ -#define RH_A_NOCP (1 << 12) /* no over current protection */ -#define RH_A_POTPGT (0xff << 24) /* power on to power good time */ - -/* urb */ -#define N_URB_TD 48 -typedef struct -{ - ed_t *ed; - __u16 length; /* number of tds associated with this request */ - __u16 td_cnt; /* number of tds already serviced */ - int state; - unsigned long pipe; - int actual_length; - td_t *td[N_URB_TD]; /* list pointer to all corresponding TDs associated with this request */ -} urb_priv_t; -#define URB_DEL 1 - -/* - * This is the full ohci controller description - * - * Note how the "proper" USB information is just - * a subset of what the full implementation needs. (Linus) - */ - - -typedef struct ohci { - struct ohci_hcca *hcca; /* hcca */ - /*dma_addr_t hcca_dma;*/ - - int irq; - int disabled; /* e.g. got a UE, we're hung */ - int sleeping; - unsigned long flags; /* for HC bugs */ - - struct ohci_regs *regs; /* OHCI controller's memory */ - - ed_t *ed_rm_list[2]; /* lists of all endpoints to be removed */ - ed_t *ed_bulktail; /* last endpoint of bulk list */ - ed_t *ed_controltail; /* last endpoint of control list */ - int intrstatus; - __u32 hc_control; /* copy of the hc control reg */ - struct usb_device *dev[32]; - struct virt_root_hub rh; - - const char *slot_name; -} ohci_t; - -#define NUM_EDS 8 /* num of preallocated endpoint descriptors */ - -struct ohci_device { - ed_t ed[NUM_EDS]; - int ed_cnt; -}; - -/* hcd */ -/* endpoint */ -static int ep_link(ohci_t * ohci, ed_t * ed); -static int ep_unlink(ohci_t * ohci, ed_t * ed); -static ed_t * ep_add_ed(struct usb_device * usb_dev, unsigned long pipe); - -/*-------------------------------------------------------------------------*/ - -/* we need more TDs than EDs */ -#define NUM_TD 64 - -/* +1 so we can align the storage */ -td_t gtd[NUM_TD+1]; -/* pointers to aligned storage */ -td_t *ptd; - -/* TDs ... */ -static inline struct td * -td_alloc (struct usb_device *usb_dev) -{ - int i; - struct td *td; - - td = NULL; - for (i = 0; i < NUM_TD; i++) - { - if (ptd[i].usb_dev == NULL) - { - td = &ptd[i]; - td->usb_dev = usb_dev; - break; - } - } - - return td; -} - -static inline void -ed_free (struct ed *ed) -{ - ed->usb_dev = NULL; -} diff --git a/doc/README.ARM-SoC b/doc/README.ARM-SoC new file mode 100644 index 0000000..0f2677f --- /dev/null +++ b/doc/README.ARM-SoC @@ -0,0 +1,31 @@ +[By Steven Scholz , 16 Aug 2004] + +Since the cpu/ directory gets clobbered with peripheral driver code I +started cleaning up cpu/arm920t. + +I introduced the concept of Soc (system on a chip) into the ./cpu +directory. That means that code that is cpu (i.e. core) specific +resides in + + cpu/$(CPU)/ + +and code that is specific to some SoC (i.e. vendor specific +peripherals around the core) is moved into + + cpu/$(CPU)/$(SOC)/ + +Thus a library/archive "cpu/$(CPU)/$(SOC)/lib$(SOC).a" will be build +and linked. Examples will be + + cpu/arm920t/imx/ + cpu/arm920t/s3c24x0 + +One can select an SoC by passing the name of it to ./mkconfig just +like + + @./mkconfig $(@:_config=) arm arm920t vcma9 mpl s3c24x0 + +If there's no VENDOR field (like "mpl" in the above line) one has to +pass NULL instead: + + @./mkconfig $(@:_config=) arm arm920t mx1ads NULL imx diff --git a/drivers/Makefile b/drivers/Makefile index 5f22158..8b73d66 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -38,9 +38,9 @@ OBJS = 3c589.o 5701rls.o ali512x.o \ pcnet.o plb2800_eth.o \ ps2ser.o ps2mult.o pc_keyb.o \ rtl8019.o rtl8139.o rtl8169.o \ - s3c24x0_i2c.o s3c4510b_eth.o s3c4510b_uart.o \ + s3c4510b_eth.o s3c4510b_uart.o \ sed13806.o sed156x.o \ - serial.o serial_imx.o serial_max3100.o \ + serial.o serial_max3100.o \ serial_pl010.o serial_pl011.o serial_xuartlite.o \ sl811_usb.o smc91111.o smiLynxEM.o status_led.o sym53c8xx.o \ ti_pci1410a.o tigon3.o \ diff --git a/drivers/s3c24x0_i2c.c b/drivers/s3c24x0_i2c.c deleted file mode 100644 index ef56cd1..0000000 --- a/drivers/s3c24x0_i2c.c +++ /dev/null @@ -1,447 +0,0 @@ -/* - * (C) Copyright 2002 - * David Mueller, ELSOFT AG, d.mueller@elsoft.ch - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* This code should work for both the S3C2400 and the S3C2410 - * as they seem to have the same I2C controller inside. - * The different address mapping is handled by the s3c24xx.h files below. - */ - -#include - -#ifdef CONFIG_DRIVER_S3C24X0_I2C - -#if defined(CONFIG_S3C2400) -#include -#elif defined(CONFIG_S3C2410) -#include -#endif -#include - -#ifdef CONFIG_HARD_I2C - -#define I2C_WRITE 0 -#define I2C_READ 1 - -#define I2C_OK 0 -#define I2C_NOK 1 -#define I2C_NACK 2 -#define I2C_NOK_LA 3 /* Lost arbitration */ -#define I2C_NOK_TOUT 4 /* time out */ - -#define I2CSTAT_BSY 0x20 /* Busy bit */ -#define I2CSTAT_NACK 0x01 /* Nack bit */ -#define I2CCON_IRPND 0x10 /* Interrupt pending bit */ -#define I2C_MODE_MT 0xC0 /* Master Transmit Mode */ -#define I2C_MODE_MR 0x80 /* Master Receive Mode */ -#define I2C_START_STOP 0x20 /* START / STOP */ -#define I2C_TXRX_ENA 0x10 /* I2C Tx/Rx enable */ - -#define I2C_TIMEOUT 1 /* 1 second */ - - -static int GetI2CSDA(void) -{ - S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO(); - -#ifdef CONFIG_S3C2410 - return (gpio->GPEDAT & 0x8000) >> 15; -#endif -#ifdef CONFIG_S3C2400 - return (gpio->PGDAT & 0x0020) >> 5; -#endif -} - -#if 0 -static void SetI2CSDA(int x) -{ - rGPEDAT = (rGPEDAT & ~0x8000) | (x&1) << 15; -} -#endif - -static void SetI2CSCL(int x) -{ - S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO(); - -#ifdef CONFIG_S3C2410 - gpio->GPEDAT = (gpio->GPEDAT & ~0x4000) | (x&1) << 14; -#endif -#ifdef CONFIG_S3C2400 - gpio->PGDAT = (gpio->PGDAT & ~0x0040) | (x&1) << 6; -#endif -} - - -static int WaitForXfer (void) -{ - S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); - int i, status; - - i = I2C_TIMEOUT * 10000; - status = i2c->IICCON; - while ((i > 0) && !(status & I2CCON_IRPND)) { - udelay (100); - status = i2c->IICCON; - i--; - } - - return (status & I2CCON_IRPND) ? I2C_OK : I2C_NOK_TOUT; -} - -static int IsACK (void) -{ - S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); - - return (!(i2c->IICSTAT & I2CSTAT_NACK)); -} - -static void ReadWriteByte (void) -{ - S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); - - i2c->IICCON &= ~I2CCON_IRPND; -} - -void i2c_init (int speed, int slaveadd) -{ - S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); - S3C24X0_GPIO *const gpio = S3C24X0_GetBase_GPIO (); - ulong freq, pres = 16, div; - int i, status; - - /* wait for some time to give previous transfer a chance to finish */ - - i = I2C_TIMEOUT * 1000; - status = i2c->IICSTAT; - while ((i > 0) && (status & I2CSTAT_BSY)) { - udelay (1000); - status = i2c->IICSTAT; - i--; - } - - if ((status & I2CSTAT_BSY) || GetI2CSDA () == 0) { -#ifdef CONFIG_S3C2410 - ulong old_gpecon = gpio->GPECON; -#endif -#ifdef CONFIG_S3C2400 - ulong old_gpecon = gpio->PGCON; -#endif - /* bus still busy probably by (most) previously interrupted transfer */ - -#ifdef CONFIG_S3C2410 - /* set I2CSDA and I2CSCL (GPE15, GPE14) to GPIO */ - gpio->GPECON = (gpio->GPECON & ~0xF0000000) | 0x10000000; -#endif -#ifdef CONFIG_S3C2400 - /* set I2CSDA and I2CSCL (PG5, PG6) to GPIO */ - gpio->PGCON = (gpio->PGCON & ~0x00003c00) | 0x00000c00; -#endif - - /* toggle I2CSCL until bus idle */ - SetI2CSCL (0); - udelay (1000); - i = 10; - while ((i > 0) && (GetI2CSDA () != 1)) { - SetI2CSCL (1); - udelay (1000); - SetI2CSCL (0); - udelay (1000); - i--; - } - SetI2CSCL (1); - udelay (1000); - - /* restore pin functions */ -#ifdef CONFIG_S3C2410 - gpio->GPECON = old_gpecon; -#endif -#ifdef CONFIG_S3C2400 - gpio->PGCON = old_gpecon; -#endif - } - - /* calculate prescaler and divisor values */ - freq = get_PCLK (); - if ((freq / pres / (16 + 1)) > speed) - /* set prescaler to 512 */ - pres = 512; - - div = 0; - while ((freq / pres / (div + 1)) > speed) - div++; - - /* set prescaler, divisor according to freq, also set - * ACKGEN, IRQ */ - i2c->IICCON = (div & 0x0F) | 0xA0 | ((pres == 512) ? 0x40 : 0); - - /* init to SLAVE REVEIVE and set slaveaddr */ - i2c->IICSTAT = 0; - i2c->IICADD = slaveadd; - /* program Master Transmit (and implicit STOP) */ - i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA; - -} - -/* - * cmd_type is 0 for write, 1 for read. - * - * addr_len can take any value from 0-255, it is only limited - * by the char, we could make it larger if needed. If it is - * 0 we skip the address write cycle. - */ -static -int i2c_transfer (unsigned char cmd_type, - unsigned char chip, - unsigned char addr[], - unsigned char addr_len, - unsigned char data[], unsigned short data_len) -{ - S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C (); - int i, status, result; - - if (data == 0 || data_len == 0) { - /*Don't support data transfer of no length or to address 0 */ - printf ("i2c_transfer: bad call\n"); - return I2C_NOK; - } - - /* Check I2C bus idle */ - i = I2C_TIMEOUT * 1000; - status = i2c->IICSTAT; - while ((i > 0) && (status & I2CSTAT_BSY)) { - udelay (1000); - status = i2c->IICSTAT; - i--; - } - - if (status & I2CSTAT_BSY) - return I2C_NOK_TOUT; - - i2c->IICCON |= 0x80; - result = I2C_OK; - - switch (cmd_type) { - case I2C_WRITE: - if (addr && addr_len) { - i2c->IICDS = chip; - /* send START */ - i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP; - i = 0; - while ((i < addr_len) && (result == I2C_OK)) { - result = WaitForXfer (); - i2c->IICDS = addr[i]; - ReadWriteByte (); - i++; - } - i = 0; - while ((i < data_len) && (result == I2C_OK)) { - result = WaitForXfer (); - i2c->IICDS = data[i]; - ReadWriteByte (); - i++; - } - } else { - i2c->IICDS = chip; - /* send START */ - i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP; - i = 0; - while ((i < data_len) && (result = I2C_OK)) { - result = WaitForXfer (); - i2c->IICDS = data[i]; - ReadWriteByte (); - i++; - } - } - - if (result == I2C_OK) - result = WaitForXfer (); - - /* send STOP */ - i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA; - ReadWriteByte (); - break; - - case I2C_READ: - if (addr && addr_len) { - i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA; - i2c->IICDS = chip; - /* send START */ - i2c->IICSTAT |= I2C_START_STOP; - result = WaitForXfer (); - if (IsACK ()) { - i = 0; - while ((i < addr_len) && (result == I2C_OK)) { - i2c->IICDS = addr[i]; - ReadWriteByte (); - result = WaitForXfer (); - i++; - } - - i2c->IICDS = chip; - /* resend START */ - i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA | - I2C_START_STOP; - ReadWriteByte (); - result = WaitForXfer (); - i = 0; - while ((i < data_len) && (result == I2C_OK)) { - /* disable ACK for final READ */ - if (i == data_len - 1) - i2c->IICCON &= ~0x80; - ReadWriteByte (); - result = WaitForXfer (); - data[i] = i2c->IICDS; - i++; - } - } else { - result = I2C_NACK; - } - - } else { - i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA; - i2c->IICDS = chip; - /* send START */ - i2c->IICSTAT |= I2C_START_STOP; - result = WaitForXfer (); - - if (IsACK ()) { - i = 0; - while ((i < data_len) && (result == I2C_OK)) { - /* disable ACK for final READ */ - if (i == data_len - 1) - i2c->IICCON &= ~0x80; - ReadWriteByte (); - result = WaitForXfer (); - data[i] = i2c->IICDS; - i++; - } - } else { - result = I2C_NACK; - } - } - - /* send STOP */ - i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA; - ReadWriteByte (); - break; - - default: - printf ("i2c_transfer: bad call\n"); - result = I2C_NOK; - break; - } - - return (result); -} - -int i2c_probe (uchar chip) -{ - uchar buf[1]; - - buf[0] = 0; - - /* - * What is needed is to send the chip address and verify that the - * address was ed (i.e. there was a chip at that address which - * drove the data line low). - */ - return (i2c_transfer (I2C_READ, chip << 1, 0, 0, buf, 1) != I2C_OK); -} - -int i2c_read (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - uchar xaddr[4]; - int ret; - - if (alen > 4) { - printf ("I2C read: addr len %d not supported\n", alen); - return 1; - } - - if (alen > 0) { - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - } - -#ifdef CFG_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of - * address and the extra bits end up in the "chip address" - * bit slots. This makes a 24WC08 (1Kbyte) chip look like - * four 256 byte chips. - * - * Note that we consider the length of the address field to - * still be one byte because the extra address bits are - * hidden in the chip address. - */ - if (alen > 0) - chip |= ((addr >> (alen * 8)) & CFG_I2C_EEPROM_ADDR_OVERFLOW); -#endif - if ((ret = - i2c_transfer (I2C_READ, chip << 1, &xaddr[4 - alen], alen, - buffer, len)) != 0) { - printf ("I2c read: failed %d\n", ret); - return 1; - } - return 0; -} - -int i2c_write (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - uchar xaddr[4]; - - if (alen > 4) { - printf ("I2C write: addr len %d not supported\n", alen); - return 1; - } - - if (alen > 0) { - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - } -#ifdef CFG_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of - * address and the extra bits end up in the "chip address" - * bit slots. This makes a 24WC08 (1Kbyte) chip look like - * four 256 byte chips. - * - * Note that we consider the length of the address field to - * still be one byte because the extra address bits are - * hidden in the chip address. - */ - if (alen > 0) - chip |= ((addr >> (alen * 8)) & CFG_I2C_EEPROM_ADDR_OVERFLOW); -#endif - return (i2c_transfer - (I2C_WRITE, chip << 1, &xaddr[4 - alen], alen, buffer, - len) != 0); -} -#endif /* CONFIG_HARD_I2C */ - -#endif /* CONFIG_DRIVER_S3C24X0_I2C */ diff --git a/drivers/serial_imx.c b/drivers/serial_imx.c deleted file mode 100644 index 9dbaa56..0000000 --- a/drivers/serial_imx.c +++ /dev/null @@ -1,201 +0,0 @@ -/* - * (c) 2004 Sascha Hauer - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#include -#if defined (CONFIG_IMX) - -#include - -#ifndef CONFIG_IMX_SERIAL_NONE - -#if defined CONFIG_IMX_SERIAL1 -#define UART_BASE IMX_UART1_BASE -#elif defined CONFIG_IMX_SERIAL2 -#define UART_BASE IMX_UART2_BASE -#else -#error "define CONFIG_IMX_SERIAL1, CONFIG_IMX_SERIAL2 or CONFIG_IMX_SERIAL_NONE" -#endif - -struct imx_serial { - volatile uint32_t urxd[16]; - volatile uint32_t utxd[16]; - volatile uint32_t ucr1; - volatile uint32_t ucr2; - volatile uint32_t ucr3; - volatile uint32_t ucr4; - volatile uint32_t ufcr; - volatile uint32_t usr1; - volatile uint32_t usr2; - volatile uint32_t uesc; - volatile uint32_t utim; - volatile uint32_t ubir; - volatile uint32_t ubmr; - volatile uint32_t ubrc; - volatile uint32_t bipr[4]; - volatile uint32_t bmpr[4]; - volatile uint32_t uts; -}; - -void serial_setbrg (void) -{ - serial_init(); -} - -extern void imx_gpio_mode(int gpio_mode); - -/* - * Initialise the serial port with the given baudrate. The settings - * are always 8 data bits, no parity, 1 stop bit, no start bits. - * - */ -int serial_init (void) -{ - volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; -#ifdef CONFIG_IMX_SERIAL1 - imx_gpio_mode(PC11_PF_UART1_TXD); - imx_gpio_mode(PC12_PF_UART1_RXD); -#else - imx_gpio_mode(PB30_PF_UART2_TXD); - imx_gpio_mode(PB31_PF_UART2_RXD); -#endif - - /* Disable UART */ - base->ucr1 &= ~UCR1_UARTEN; - - /* Set to default POR state */ - - base->ucr1 = 0x00000004; - base->ucr2 = 0x00000000; - base->ucr3 = 0x00000000; - base->ucr4 = 0x00008040; - base->uesc = 0x0000002B; - base->utim = 0x00000000; - base->ubir = 0x00000000; - base->ubmr = 0x00000000; - base->uts = 0x00000000; - /* Set clocks */ - base->ucr4 |= UCR4_REF16; - - /* Configure FIFOs */ - base->ufcr = 0xa81; - - /* Set the numerator value minus one of the BRM ratio */ - base->ubir = (CONFIG_BAUDRATE / 100) - 1; - - /* Set the denominator value minus one of the BRM ratio */ - base->ubmr = 10000 - 1; - - /* Set to 8N1 */ - base->ucr2 &= ~UCR2_PREN; - base->ucr2 |= UCR2_WS; - base->ucr2 &= ~UCR2_STPB; - - /* Ignore RTS */ - base->ucr2 |= UCR2_IRTS; - - /* Enable UART */ - base->ucr1 |= UCR1_UARTEN | UCR1_UARTCLKEN; - - /* Enable FIFOs */ - base->ucr2 |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN; - - /* Clear status flags */ - base->usr2 |= USR2_ADET | - USR2_DTRF | - USR2_IDLE | - USR2_IRINT | - USR2_WAKE | - USR2_RTSF | - USR2_BRCD | - USR2_ORE | - USR2_RDR; - - /* Clear status flags */ - base->usr1 |= USR1_PARITYERR | - USR1_RTSD | - USR1_ESCF | - USR1_FRAMERR | - USR1_AIRINT | - USR1_AWAKE; - return (0); -} - -/* - * Read a single byte from the serial port. Returns 1 on success, 0 - * otherwise. When the function is successful, the character read is - * written into its argument c. - */ -int serial_getc (void) -{ - volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; - unsigned char ch; - - while(base->uts & UTS_RXEMPTY); - - ch = (char)base->urxd[0]; - - return ch; -} - -#ifdef CONFIG_HWFLOW -static int hwflow = 0; /* turned off by default */ -int hwflow_onoff(int on) -{ -} -#endif - -/* - * Output a single byte to the serial port. - */ -void serial_putc (const char c) -{ - volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; - - /* Wait for Tx FIFO not full */ - while (base->uts & UTS_TXFULL); - - base->utxd[0] = c; - - /* If \n, also do \r */ - if (c == '\n') - serial_putc ('\r'); -} - -/* - * Test whether a character is in the RX buffer - */ -int serial_tstc (void) -{ - volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; - - /* If receive fifo is empty, return false */ - if (base->uts & UTS_RXEMPTY) - return 0; - return 1; -} - -void -serial_puts (const char *s) -{ - while (*s) { - serial_putc (*s++); - } -} -#endif /* CONFIG_IMX_SERIAL_NONE */ -#endif /* defined CONFIG_IMX */ diff --git a/mkconfig b/mkconfig index 106bd89..266addd 100644 --- a/mkconfig +++ b/mkconfig @@ -3,7 +3,7 @@ # Script to create header files and links to configure # U-Boot for a specific board. # -# Parameters: Target Architecture CPU Board +# Parameters: Target Architecture CPU Board [VENDOR] [SOC] # # (C) 2002 DENX Software Engineering, Wolfgang Denk # @@ -19,7 +19,7 @@ while [ $# -gt 0 ] ; do done [ $# -lt 4 ] && exit 1 -[ $# -gt 5 ] && exit 1 +[ $# -gt 6 ] && exit 1 echo "Configuring for $1 board..." @@ -41,11 +41,13 @@ fi # # Create include file for Make # -echo "ARCH = $2" > config.mk -echo "CPU = $3" >> config.mk -echo "BOARD = $4" >> config.mk +echo "ARCH = $2" > config.mk +echo "CPU = $3" >> config.mk +echo "BOARD = $4" >> config.mk -[ "$5" ] && echo "VENDOR = $5" >> config.mk +[ "$5" ] && [ "$5" != "NULL" ] && echo "VENDOR = $5" >> config.mk + +[ "$6" ] && [ "$6" != "NULL" ] && echo "SOC = $6" >> config.mk # # Create board specific header file -- cgit v0.10.2