From 1cc0a9f49657734c54939f03fc1e3ca0ec9d7eef Mon Sep 17 00:00:00 2001 From: "Robert P. J. Day" Date: Wed, 4 May 2016 04:47:31 -0400 Subject: Fix various typos, scattered over the code. Spelling corrections for (among other things): * environment * override * variable * ftd (should be "fdt", for flattened device tree) * embedded * FTDI * emulation * controller diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c index d580a43..a9b12a4 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c @@ -180,7 +180,7 @@ ulong get_ddr_freq(ulong ctrl_num) /* * DDR controller 0 & 1 are on memory complex 0 - * DDR controler 2 is on memory complext 1 + * DDR controller 2 is on memory complext 1 */ #ifdef CONFIG_SYS_FSL_HAS_DP_DDR if (ctrl_num >= 2) diff --git a/arch/arm/mach-uniphier/boot-mode/boot-mode.c b/arch/arm/mach-uniphier/boot-mode/boot-mode.c index 48e478c..b180f44 100644 --- a/arch/arm/mach-uniphier/boot-mode/boot-mode.c +++ b/arch/arm/mach-uniphier/boot-mode/boot-mode.c @@ -114,7 +114,7 @@ static int do_mmcsetn(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) U_BOOT_CMD( mmcsetn, 1, 1, do_mmcsetn, - "Set the first MMC (not SD) dev number to \"mmc_first_dev\" enviroment", + "Set the first MMC (not SD) dev number to \"mmc_first_dev\" environment", "" ); #endif diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index f852a1f..fe37d1f 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -145,7 +145,7 @@ config MIPS_BOOT_ENV_LEGACY Enable this option if you want U-Boot to hand over the Yamon-style environment to the kernel. Information like memory size, initrd address and size will be prepared as zero-terminated key/value list. - The address of the enviroment is stored in register $a2. + The address of the environment is stored in register $a2. config MIPS_BOOT_FDT bool "Hand over a flattened device tree to Linux kernel" diff --git a/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c b/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c index 916451a..455136c 100644 --- a/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c +++ b/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c @@ -1151,7 +1151,7 @@ phys_size_t initdram(int board_type) dram_size *= ranks; debug("dram_size = %lu\n", dram_size); - /* Start the SDRAM controler */ + /* Start the SDRAM controller */ mtsdram(DDR0_02, DDR0_02_START_ENCODE(1)); denali_wait_for_dlllock(); diff --git a/board/freescale/common/fsl_validate.c b/board/freescale/common/fsl_validate.c index 64e4e30..8c171b1 100644 --- a/board/freescale/common/fsl_validate.c +++ b/board/freescale/common/fsl_validate.c @@ -812,9 +812,9 @@ static int calculate_cmp_img_sig(struct fsl_secboot_img_priv *img) } /* haddr - Address of the header of image to be validated. * arg_hash_str - Option hash string. If provided, this - * overides the key hash in the SFP fuses. + * overrides the key hash in the SFP fuses. * img_addr_ptr - Optional pointer to address of image to be validated. - * If non zero addr, this overides the addr of image in header, + * If non zero addr, this overrides the addr of image in header, * otherwise updated to image addr in header. * Acts as both input and output of function. * This pointer shouldn't be NULL. diff --git a/board/freescale/mx28evk/README b/board/freescale/mx28evk/README index a248fb2..b8bee89 100644 --- a/board/freescale/mx28evk/README +++ b/board/freescale/mx28evk/README @@ -45,7 +45,7 @@ or or -"make mx28evk_spi_config" - store enviroment variables into SPI NOR flash +"make mx28evk_spi_config" - store environment variables into SPI NOR flash Choose the target accordingly. diff --git a/cmd/fdt.c b/cmd/fdt.c index 4c18962..898217f 100644 --- a/cmd/fdt.c +++ b/cmd/fdt.c @@ -1055,7 +1055,7 @@ static char fdt_help_text[] = " - addr of key blob\n" " default gd->fdt_blob\n" #endif - "NOTE: Dereference aliases by omiting the leading '/', " + "NOTE: Dereference aliases by omitting the leading '/', " "e.g. fdt print ethernet0."; #endif diff --git a/cmd/mtdparts.c b/cmd/mtdparts.c index 86a4689..44b2c3a 100644 --- a/cmd/mtdparts.c +++ b/cmd/mtdparts.c @@ -1742,7 +1742,7 @@ int mtdparts_init(void) debug("last_partition : %s\n", last_partition); debug("env_partition : %s\n", current_partition); - /* if mtdids varible is empty try to use defaults */ + /* if mtdids variable is empty try to use defaults */ if (!ids) { if (mtdids_default) { debug("mtdids variable not defined, using default\n"); diff --git a/doc/README.commands.spl b/doc/README.commands.spl index ac33273..cb3e0c8 100644 --- a/doc/README.commands.spl +++ b/doc/README.commands.spl @@ -10,7 +10,7 @@ export has two subcommands: fdt: exports the FDT Call is: -spl export [kernel_addr] [initrd_addr] [fdt_addr if fdt] +spl export [kernel_addr] [initrd_addr] [fdt_addr if fdt] TYPICAL CALL diff --git a/doc/README.marubun-pcmcia b/doc/README.marubun-pcmcia index d3563a3..0a363b2 100644 --- a/doc/README.marubun-pcmcia +++ b/doc/README.marubun-pcmcia @@ -34,7 +34,7 @@ U-Boot MARUBUN MR-SHPC-01 PCMCIA controller driver ex. #define CONFIG_PCMCIA_SLOT_A 1 * CONFIG_SYS_MARUBUN_MRSHPC - This is MR-SHPC-01 PCMCIA controler base address. + This is MR-SHPC-01 PCMCIA controller base address. You should do the setting matched to your environment. ex. #define CONFIG_SYS_MARUBUN_MRSHPC 0xb03fffe0 ( for MS7722SE01 environment ) diff --git a/doc/README.mxs b/doc/README.mxs index 6ea73b9..4edf19f 100644 --- a/doc/README.mxs +++ b/doc/README.mxs @@ -219,7 +219,7 @@ There are two possibilities when preparing an image writable to NAND flash. This script expects a working TFTP server containing the file "u-boot.nand" in it's root directory. This can be changed by - adjusting the "update_nand_full_filename" varible. + adjusting the "update_nand_full_filename" variable. To update the system, run the following in U-Boot prompt: @@ -242,7 +242,7 @@ There are two possibilities when preparing an image writable to NAND flash. This script expects a working TFTP server containing the file "u-boot.sb" in it's root directory. This can be changed by - adjusting the "update_nand_firmware_filename" varible. + adjusting the "update_nand_firmware_filename" variable. To update the system, run the following in U-Boot prompt: diff --git a/doc/SPI/README.sandbox-spi b/doc/SPI/README.sandbox-spi index bb73eaf..dfa845c 100644 --- a/doc/SPI/README.sandbox-spi +++ b/doc/SPI/README.sandbox-spi @@ -1,7 +1,7 @@ Sandbox SPI/SPI Flash Implementation ==================================== -U-Boot supports SPI and SPI flash emuation in sandbox. This must be enabled +U-Boot supports SPI and SPI flash emulation in sandbox. This must be enabled using the --spi_sf paramter when starting U-Boot. For example: diff --git a/doc/SPI/README.ti_qspi_flash b/doc/SPI/README.ti_qspi_flash index 9064739..5cc1fd0 100644 --- a/doc/SPI/README.ti_qspi_flash +++ b/doc/SPI/README.ti_qspi_flash @@ -31,7 +31,7 @@ Can be used in: Memory mapped read mode ----------------------- In this, SPI controller is configured using configuration port and then -controler is switched to memory mapped port for data read. +controller is switched to memory mapped port for data read. Driver ------ diff --git a/drivers/bios_emulator/x86emu/decode.c b/drivers/bios_emulator/x86emu/decode.c index da44c3d..a9a01b5 100644 --- a/drivers/bios_emulator/x86emu/decode.c +++ b/drivers/bios_emulator/x86emu/decode.c @@ -241,7 +241,7 @@ no segment override. Address modes such as -3[BP] or 10[BP+SI] all refer to addresses relative to SS (ie: on the stack). So, at the minimum, all decodings of addressing modes would have to set/clear a bit describing whether the access is relative to DS or SS. That is the function of the -cpu-state-varible M.x86.mode. There are several potential states: +cpu-state-variable M.x86.mode. There are several potential states: repe prefix seen (handled elsewhere) repne prefix seen (ditto) diff --git a/drivers/dfu/Kconfig b/drivers/dfu/Kconfig index 4fe2219..6b92064 100644 --- a/drivers/dfu/Kconfig +++ b/drivers/dfu/Kconfig @@ -3,8 +3,8 @@ menu "DFU support" config DFU_TFTP bool "DFU via TFTP" help - This option allows performing update of DFU managed medium with data - send via TFTP boot. - Detailed description of this feature can be found at ./doc/README.dfutftp + This option allows performing update of DFU-managed medium with data + sent via TFTP boot. + Detailed description of this feature can be found at ./doc/README.dfutftp endmenu diff --git a/drivers/net/macb.c b/drivers/net/macb.c index be0659a..4bf8fa4 100644 --- a/drivers/net/macb.c +++ b/drivers/net/macb.c @@ -120,7 +120,7 @@ static int macb_is_gem(struct macb_device *macb) static int gem_is_gigabit_capable(struct macb_device *macb) { /* - * The GEM controllers embeded in SAMA5D2 and SAMA5D4 are + * The GEM controllers embedded in SAMA5D2 and SAMA5D4 are * configured to support only 10/100. */ return macb_is_gem(macb) && !cpu_is_sama5d2() && !cpu_is_sama5d4(); diff --git a/drivers/net/sh_eth.c b/drivers/net/sh_eth.c index 443a4da..2fa2016 100644 --- a/drivers/net/sh_eth.c +++ b/drivers/net/sh_eth.c @@ -1,5 +1,5 @@ /* - * sh_eth.c - Driver for Renesas ethernet controler. + * sh_eth.c - Driver for Renesas ethernet controller. * * Copyright (C) 2008, 2011 Renesas Solutions Corp. * Copyright (c) 2008, 2011, 2014 2014 Nobuhiro Iwamatsu diff --git a/drivers/net/sh_eth.h b/drivers/net/sh_eth.h index 5cb520c..3645f0e 100644 --- a/drivers/net/sh_eth.h +++ b/drivers/net/sh_eth.h @@ -1,5 +1,5 @@ /* - * sh_eth.h - Driver for Renesas SuperH ethernet controler. + * sh_eth.h - Driver for Renesas SuperH ethernet controller. * * Copyright (C) 2008 - 2012 Renesas Solutions Corp. * Copyright (c) 2008 - 2012 Nobuhiro Iwamatsu diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index 3c6b36d..8e22ea7 100644 --- a/drivers/thermal/Kconfig +++ b/drivers/thermal/Kconfig @@ -1,7 +1,7 @@ config DM_THERMAL bool "Driver support for thermal devices" help - Enable support for temporary-sensing devices. Some SoCs have on-chip + Enable support for temperature-sensing devices. Some SoCs have on-chip temperature sensors to permit warnings, speed throttling or even automatic power-off when the temperature gets too high or low. Other devices may be discrete but connected on a suitable bus. diff --git a/include/configs/hikey.h b/include/configs/hikey.h index 83d9e10..ffcc4d2 100644 --- a/include/configs/hikey.h +++ b/include/configs/hikey.h @@ -121,7 +121,7 @@ "initrd_high=0xffffffffffffffff\0" \ BOOTENV -/* Preserve enviroment on sd card */ +/* Preserve environment on sd card */ #define CONFIG_COMMAND_HISTORY #define CONFIG_ENV_SIZE 0x1000 diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h index 6c79643..3c11e2a 100644 --- a/include/configs/omap3_logic.h +++ b/include/configs/omap3_logic.h @@ -140,7 +140,7 @@ #define CONFIG_PREBOOT \ "echo ======================NOTICE============================;"\ "echo \"The u-boot environment is not set.\";" \ - "echo \"If using a display a valid display varible for your panel\";" \ + "echo \"If using a display a valid display variable for your panel\";" \ "echo \"needs to be set.\";" \ "echo \"Valid display options are:\";" \ "echo \" 2 == LQ121S1DG31 TFT SVGA (12.1) Sharp\";" \ diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h index 1f33bc6..816c571 100644 --- a/include/configs/pengwyn.h +++ b/include/configs/pengwyn.h @@ -102,7 +102,7 @@ "run mmcboot;" \ "run nandboot;" -/* NS16550 Configuration: primary UART via FDTI */ +/* NS16550 Configuration: primary UART via FTDI */ #define CONFIG_SYS_NS16550_COM1 0x44e09000 #define CONFIG_BAUDRATE 115200 diff --git a/include/fdtdec.h b/include/fdtdec.h index fb88273..37d482a 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -570,7 +570,7 @@ int fdtdec_check_fdt(void); * @param id Compatible ID to look for * @param node_list Place to put list of found nodes * @param maxcount Maximum number of nodes to find - * @return number of nodes found on success, FTD_ERR_... on error + * @return number of nodes found on success, FDT_ERR_... on error */ int fdtdec_find_aliases_for_id(const void *blob, const char *name, enum fdt_compat_id id, int *node_list, int maxcount); diff --git a/tools/moveconfig.py b/tools/moveconfig.py index 6f71b55..68631b7 100755 --- a/tools/moveconfig.py +++ b/tools/moveconfig.py @@ -273,12 +273,12 @@ def log_msg(color_enabled, color, defconfig, msg): color_text(color_enabled, color, msg) + '\n' def update_cross_compile(): - """Update per-arch CROSS_COMPILE via enviroment variables + """Update per-arch CROSS_COMPILE via environment variables The default CROSS_COMPILE values are available in the CROSS_COMPILE list above. - You can override them via enviroment variables + You can override them via environment variables CROSS_COMPILE_{ARCH}. For example, if you want to override toolchain prefixes -- cgit v0.10.2