From 0d43fded20e390e2e779ae4fa831fc00157f454a Mon Sep 17 00:00:00 2001 From: "Derald D. Woods" Date: Sun, 6 Aug 2017 00:00:21 -0500 Subject: omap3: evm: Update board, defconfig, and maintainer file This patch brings the OMAP3 EVM to a bootable state, on master, as of v2017.09-rc1. Signed-off-by: Derald D. Woods Reviewed-by: Tom Rini diff --git a/board/ti/evm/MAINTAINERS b/board/ti/evm/MAINTAINERS index 612a08a..cd315c1 100644 --- a/board/ti/evm/MAINTAINERS +++ b/board/ti/evm/MAINTAINERS @@ -1,5 +1,5 @@ EVM BOARD -M: Tom Rini +M: Derald D. Woods S: Maintained F: board/ti/evm/ F: include/configs/omap3_evm.h diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c index a6c5a3d..6f75bd1 100644 --- a/board/ti/evm/evm.c +++ b/board/ti/evm/evm.c @@ -12,6 +12,8 @@ * SPDX-License-Identifier: GPL-2.0+ */ #include +#include +#include #include #include #include @@ -22,14 +24,35 @@ #include #include #include +#include #include +#include +#include +#include #include "evm.h" -#define OMAP3EVM_GPIO_ETH_RST_GEN1 64 -#define OMAP3EVM_GPIO_ETH_RST_GEN2 7 +#ifdef CONFIG_USB_EHCI_HCD +#include +#include +#endif + +#define OMAP3EVM_GPIO_ETH_RST_GEN1 64 +#define OMAP3EVM_GPIO_ETH_RST_GEN2 7 DECLARE_GLOBAL_DATA_PTR; +static const struct ns16550_platdata omap3_evm_serial = { + .base = OMAP34XX_UART1, + .reg_shift = 2, + .clock = V_NS16550_CLK, + .fcr = UART_FCR_DEFVAL, +}; + +U_BOOT_DEVICE(omap3_evm_uart) = { + "ns16550_serial", + &omap3_evm_serial +}; + static u32 omap3_evm_version; u32 get_omap3_evm_rev(void) @@ -60,25 +83,19 @@ static void omap3_evm_get_revision(void) default: omap3_evm_version = OMAP3EVM_BOARD_GEN_2; } -#else +#else /* !CONFIG_CMD_NET */ #if defined(CONFIG_STATIC_BOARD_REV) - /* - * Look for static defintion of the board revision - */ + /* Look for static defintion of the board revision */ omap3_evm_version = CONFIG_STATIC_BOARD_REV; #else - /* - * Fallback to the default above. - */ + /* Fallback to the default above */ omap3_evm_version = OMAP3EVM_BOARD_GEN_2; -#endif -#endif /* CONFIG_CMD_NET */ +#endif /* CONFIG_STATIC_BOARD_REV */ +#endif /* CONFIG_CMD_NET */ } -#ifdef CONFIG_USB_OMAP3 -/* - * MUSB port on OMAP3EVM Rev >= E requires extvbus programming. - */ +#if defined(CONFIG_USB_MUSB_GADGET) || defined(CONFIG_USB_MUSB_HOST) +/* MUSB port on OMAP3EVM Rev >= E requires extvbus programming. */ u8 omap3_evm_need_extvbus(void) { u8 retval = 0; @@ -88,7 +105,7 @@ u8 omap3_evm_need_extvbus(void) return retval; } -#endif +#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */ /* * Routine: board_init @@ -105,7 +122,7 @@ int board_init(void) return 0; } -#ifdef CONFIG_SPL_BUILD +#if defined(CONFIG_SPL_BUILD) /* * Routine: get_board_mem_timings * Description: If we use SPL then there is no x-loader nor config header @@ -138,7 +155,34 @@ void get_board_mem_timings(struct board_sdrc_timings *timings) timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; timings->mr = MICRON_V_MR_165; } -#endif +#endif /* CONFIG_SPL_BUILD */ + +#if defined(CONFIG_USB_MUSB_OMAP2PLUS) +static struct musb_hdrc_config musb_config = { + .multipoint = 1, + .dyn_fifo = 1, + .num_eps = 16, + .ram_bits = 12, +}; + +static struct omap_musb_board_data musb_board_data = { + .interface_type = MUSB_INTERFACE_ULPI, +}; + +static struct musb_hdrc_platform_data musb_plat = { +#if defined(CONFIG_USB_MUSB_HOST) + .mode = MUSB_HOST, +#elif defined(CONFIG_USB_MUSB_GADGET) + .mode = MUSB_PERIPHERAL, +#else +#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET" +#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */ + .config = &musb_config, + .power = 100, + .platform_ops = &omap2430_ops, + .board_data = &musb_board_data, +}; +#endif /* CONFIG_USB_MUSB_OMAP2PLUS */ /* * Routine: misc_init_r @@ -146,6 +190,7 @@ void get_board_mem_timings(struct board_sdrc_timings *timings) */ int misc_init_r(void) { + twl4030_power_init(); #ifdef CONFIG_SYS_I2C_OMAP24XX i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); @@ -161,6 +206,13 @@ int misc_init_r(void) #endif omap_die_id_display(); +#if defined(CONFIG_USB_MUSB_OMAP2PLUS) + musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE); +#endif + +#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) + omap_die_id_usbethaddr(); +#endif return 0; } @@ -175,7 +227,7 @@ void set_muxconf_regs(void) MUX_EVM(); } -#ifdef CONFIG_CMD_NET +#if defined(CONFIG_CMD_NET) /* * Routine: setup_net_chip * Description: Setting up the configuration GPMC registers specific to the @@ -237,7 +289,7 @@ static void reset_net_chip(void) int board_eth_init(bd_t *bis) { int rc = 0; -#ifdef CONFIG_SMC911X +#if defined(CONFIG_SMC911X) #define STR_ENV_ETHADDR "ethaddr" struct eth_device *dev; @@ -254,7 +306,7 @@ int board_eth_init(bd_t *bis) rc = -1; } } -#endif +#endif /* CONFIG_SMC911X */ return rc; } #endif /* CONFIG_CMD_NET */ @@ -264,11 +316,35 @@ int board_mmc_init(bd_t *bis) { return omap_mmc_init(0, 0, 0, -1, -1); } -#endif -#if defined(CONFIG_MMC) void board_mmc_power_init(void) { twl4030_power_mmc_init(0); } -#endif +#endif /* CONFIG_MMC */ + +#if defined(CONFIG_USB_EHCI_HCD) +static struct omap_usbhs_board_data usbhs_bdata = { + .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, + .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, + .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED +}; + +int ehci_hcd_init(int index, enum usb_init_type init, + struct ehci_hccr **hccr, struct ehci_hcor **hcor) +{ + return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); +} + +int ehci_hcd_stop(int index) +{ + return omap_ehci_hcd_stop(); +} +#endif /* CONFIG_USB_EHCI_HCD */ + +#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) && !defined(CONFIG_CMD_NET) +int board_eth_init(bd_t *bis) +{ + return usb_eth_initialize(bis); +} +#endif /* CONFIG_USB_ETHER */ diff --git a/board/ti/evm/evm.h b/board/ti/evm/evm.h index 91e9b88..0f8268b 100644 --- a/board/ti/evm/evm.h +++ b/board/ti/evm/evm.h @@ -278,12 +278,19 @@ static void reset_net_chip(void); /* TS_PEN_IRQ */\ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | DIS | M4)) /*GPIO_176*/\ /* - LAN_INTR*/\ - MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0)) /*McSPI1_CS3*/\ - MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)) /*McSPI2_CLK*/\ - MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)) /*McSPI2_SIMO*/\ - MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)) /*McSPI2_SOMI*/\ - MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M0)) /*McSPI2_CS0*/\ - MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0)) /*McSPI2_CS1*/\ + /* USB EHCI (port 2) */\ + MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M3)) /*HSUSB2_DATA2*/\ + MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | EN | M3)) /*HSUSB2_DATA7*/\ + MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | EN | M3)) /*HSUSB2_DATA4*/\ + MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | EN | M3)) /*HSUSB2_DATA5*/\ + MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M3)) /*HSUSB2_DATA6*/\ + MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M3)) /*HSUSB2_DATA3*/\ + MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\ + MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\ + MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | EN | M3)) /*HSUSB2_DIR*/\ + MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | EN | M3)) /*HSUSB2_NXT*/\ + MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | EN | M3)) /*HSUSB2_DATA0*/\ + MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | EN | M3)) /*HSUSB2_DATA1*/\ /*Control and debug */\ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\ @@ -318,12 +325,6 @@ static void reset_net_chip(void); MUX_VAL(CP(ETK_D7_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D7*/\ MUX_VAL(CP(ETK_D8_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D8*/\ MUX_VAL(CP(ETK_D9_ES2 ), (IEN | PTD | DIS | M0)) /*ETK_D9*/\ - MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0)) /*ETK_D10*/\ - MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0)) /*ETK_D11*/\ - MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0)) /*ETK_D12*/\ - MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0)) /*ETK_D13*/\ - MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0)) /*ETK_D14*/\ - MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0)) /*ETK_D15*/\ /*Die to Die */\ MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\ MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\ diff --git a/configs/omap3_evm_defconfig b/configs/omap3_evm_defconfig index 620148c..9bbc980 100644 --- a/configs/omap3_evm_defconfig +++ b/configs/omap3_evm_defconfig @@ -2,32 +2,61 @@ CONFIG_ARM=y # CONFIG_SYS_THUMB_BUILD is not set CONFIG_ARCH_OMAP2PLUS=y CONFIG_SYS_TEXT_BASE=0x80100000 +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_SYS_MPUCLK=720 CONFIG_TARGET_OMAP3_EVM=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_DISTRO_DEFAULTS=y +CONFIG_SYS_EXTRA_OPTIONS="NAND" CONFIG_ENV_IS_IN_NAND=y CONFIG_BOOTDELAY=3 +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_DEFAULT_FDT_FILE="omap3-evm.dtb" +CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_STACK_R=y # CONFIG_SPL_EXT_SUPPORT is not set -CONFIG_HUSH_PARSER=y +CONFIG_SPL_MTD_SUPPORT=y CONFIG_SYS_PROMPT="OMAP3_EVM # " # CONFIG_CMD_IMI is not set # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y # CONFIG_CMD_FLASH is not set +# CONFIG_CMD_FPGA is not set +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y CONFIG_CMD_NAND=y -CONFIG_CMD_I2C=y +CONFIG_CMD_NAND_TRIMFFS=y +CONFIG_CMD_SPI=y CONFIG_CMD_USB=y -# CONFIG_CMD_FPGA is not set -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_PING=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_JFFS2=y -CONFIG_EFI_PARTITION=y -# CONFIG_PARTITION_UUIDS is not set -# CONFIG_SPL_PARTITION_UUIDS is not set +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FS_UUID=y +CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0" +CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:512k(spl),1792k(u-boot),128k(dtb),128k(u-boot-env),6m(kernel),-(rootfs)" +CONFIG_CMD_UBI=y +# CONFIG_ISO_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +CONFIG_SPL_PARTITION_UUIDS=y +CONFIG_DM=y +CONFIG_SPL_DM=y +CONFIG_DM_GPIO=y CONFIG_MMC_OMAP_HS=y +CONFIG_MTD=y +CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_USB=y -CONFIG_USB_STORAGE=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_G_DNL_MANUFACTURER="Texas Instruments" +CONFIG_G_DNL_VENDOR_NUM=0x0451 +CONFIG_G_DNL_PRODUCT_NUM=0x5678 +CONFIG_FAT_WRITE=y +CONFIG_OF_LIBFDT=y +CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_SPL_OF_LIBFDT=y +# CONFIG_EFI_LOADER is not set diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index bc859c8..9930483 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -14,348 +14,138 @@ * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __OMAP3EVM_CONFIG_H -#define __OMAP3EVM_CONFIG_H +#ifndef __CONFIG_H +#define __CONFIG_H -#include -#include +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ -/* ---------------------------------------------------------------------------- - * Supported U-Boot features - * ---------------------------------------------------------------------------- - */ -#define CONFIG_SYS_LONGHELP - -/* Allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Add auto-completion support */ -#define CONFIG_AUTO_COMPLETE - -/* ---------------------------------------------------------------------------- - * Supported hardware - * ---------------------------------------------------------------------------- - */ - -/* SPL */ -#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 -#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" - -/* Partition tables */ - -/* USB - * - * Enable CONFIG_USB_MUSB_HCD for Host functionalities MSC, keyboard - * Enable CONFIG_USB_MUSB_UDD for Device functionalities. - */ -#define CONFIG_USB_OMAP3 -#define CONFIG_USB_MUSB_HCD -/* #define CONFIG_USB_MUSB_UDC */ - -/* NAND SPL */ -#define CONFIG_SPL_NAND_SIMPLE -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_ECC -#define CONFIG_SYS_NAND_5_ADDR_CYCLE -#define CONFIG_SYS_NAND_PAGE_COUNT 64 -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 -#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ - 10, 11, 12, 13} -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 - -/* - * High level configuration options - */ - -#define CONFIG_SDRC /* The chip has SDRC controller */ - -/* - * Clock related definitions - */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/* Size of environment - 128KB */ -#define CONFIG_ENV_SIZE (128 << 10) - -/* Size of malloc pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) - -/* - * Physical Memory Map - * Note 1: CS1 may or may not be populated - * Note 2: SDRAM size is expected to be at least 32MB - */ -#define CONFIG_NR_DRAM_BANKS 2 -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 - -/* Limits for memtest */ -#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) -#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ - 0x01F00000) /* 31MB */ - -/* Default load address */ -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) - -/* ----------------------------------------------------------------------------- - * Hardware drivers - * ----------------------------------------------------------------------------- - */ - -/* - * NS16550 Configuration - */ -#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK - -/* - * select serial console configuration - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */ -#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ - 115200} - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 -#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#include /* - * PISMO support + * We are only ever GP parts and will utilize all of the "downloaded image" + * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB). */ -/* Monitor at start of flash - Reserve 2 sectors */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) - -/* Start location & size of environment */ -#define ONENAND_ENV_OFFSET 0x260000 -#define SMNAND_ENV_OFFSET 0x260000 +#undef CONFIG_SPL_TEXT_BASE +#define CONFIG_SPL_TEXT_BASE 0x40200000 -#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ - -/* - * NAND - */ -/* Physical address to access NAND */ -#define CONFIG_SYS_NAND_ADDR NAND_BASE - -/* Physical address to access NAND at CS0 */ -#define CONFIG_SYS_NAND_BASE NAND_BASE - -/* Max number of NAND devices */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BUSWIDTH_16BIT -/* Timeout values (in ticks) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ) -#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ) - -/* Flash banks JFFS2 should use */ -#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \ - CONFIG_SYS_MAX_NAND_DEVICE) - -#define CONFIG_SYS_JFFS2_MEM_NAND -#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 - -#define CONFIG_JFFS2_NAND -/* nand device jffs2 lives on */ -#define CONFIG_JFFS2_DEV "nand0" -/* Start of jffs2 partition */ -#define CONFIG_JFFS2_PART_OFFSET 0x680000 -/* Size of jffs2 partition */ -#define CONFIG_JFFS2_PART_SIZE 0xf980000 - -/* - * USB - */ -#ifdef CONFIG_USB_OMAP3 - -#ifdef CONFIG_USB_MUSB_HCD - -#ifdef CONFIG_USB_KEYBOARD -#define CONFIG_SYS_USB_EVENT_POLL -#define CONFIG_PREBOOT "usb start" -#endif /* CONFIG_USB_KEYBOARD */ - -#endif /* CONFIG_USB_MUSB_HCD */ - -#ifdef CONFIG_USB_MUSB_UDC -/* USB device configuration */ -#define CONFIG_USB_DEVICE -#define CONFIG_USB_TTY - -/* Change these to suit your needs */ -#define CONFIG_USBD_VENDORID 0x0451 -#define CONFIG_USBD_PRODUCTID 0x5678 -#define CONFIG_USBD_MANUFACTURER "Texas Instruments" -#define CONFIG_USBD_PRODUCT_NAME "EVM" -#endif /* CONFIG_USB_MUSB_UDC */ - -#endif /* CONFIG_USB_OMAP3 */ - -/* ---------------------------------------------------------------------------- - * U-Boot features - * ---------------------------------------------------------------------------- - */ -#define CONFIG_SYS_MAXARGS 16 /* max args for a command */ +#define CONFIG_SPL_FRAMEWORK #define CONFIG_MISC_INIT_R - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG -/* Size of Console IO buffer */ -#define CONFIG_SYS_CBSIZE 512 - -/* Size of print buffer */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) - -/* Size of bootarg buffer */ -#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) -#define CONFIG_BOOTFILE "uImage" +/* Override OMAP3 serial console configuration */ +#undef CONFIG_CONS_INDEX +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 +#if defined(CONFIG_SPL_BUILD) +#undef CONFIG_SYS_NS16550_REG_SIZE +#else /* !CONFIG_SPL_BUILD */ +#define CONFIG_SYS_NS16550_REG_SIZE (-1) +#endif /* CONFIG_SPL_BUILD */ -/* - * NAND / OneNAND - */ -#if defined(CONFIG_CMD_NAND) +/* NAND */ +#if defined(CONFIG_NAND) +#define CONFIG_NAND_OMAP_GPMC #define CONFIG_SYS_FLASH_BASE NAND_BASE +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_BCH +#define CONFIG_SYS_NAND_BUSWIDTH_16BIT +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ + 10, 11, 12, 13} +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 +#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ +#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET +#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SPL_OMAP3_ID_NAND +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */ +#endif /* CONFIG_NAND */ -#define CONFIG_NAND_OMAP_GPMC -#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET -#elif defined(CONFIG_CMD_ONENAND) -#define CONFIG_SYS_FLASH_BASE ONENAND_MAP -#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP -#endif +#define CONFIG_USB_OMAP3 -#if !defined(CONFIG_ENV_IS_NOWHERE) -#if defined(CONFIG_CMD_NAND) -#elif defined(CONFIG_CMD_ONENAND) -#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET -#endif -#endif /* CONFIG_ENV_IS_NOWHERE */ +/* MUSB */ +#define CONFIG_USB_MUSB_OMAP2PLUS +#define CONFIG_USB_MUSB_PIO_ONLY +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETHER_RNDIS -#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET +/* USB EHCI */ +#define CONFIG_SYS_USB_FAT_BOOT_PARTITION 1 +/* SMSC911x Ethernet */ #if defined(CONFIG_CMD_NET) - -/* Ethernet (SMSC9115 from SMSC9118 family) */ #define CONFIG_SMC911X #define CONFIG_SMC911X_32_BIT -#define CONFIG_SMC911X_BASE 0x2C000000 - -/* BOOTP fields */ -#define CONFIG_BOOTP_SUBNETMASK 0x00000001 -#define CONFIG_BOOTP_GATEWAY 0x00000002 -#define CONFIG_BOOTP_HOSTNAME 0x00000004 -#define CONFIG_BOOTP_BOOTPATH 0x00000010 - +#define CONFIG_SMC911X_BASE 0x2C000000 #endif /* CONFIG_CMD_NET */ -/* Support for relocation */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* ----------------------------------------------------------------------------- - * Board specific - * ----------------------------------------------------------------------------- - */ - -/* Uncomment to define the board revision statically */ -/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */ - -/* Defines for SPL */ -#define CONFIG_SPL_FRAMEWORK -#define CONFIG_SPL_TEXT_BASE 0x40200800 -#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ - CONFIG_SPL_TEXT_BASE) - -#define CONFIG_SPL_BSS_START_ADDR 0x80000000 -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ - -#define CONFIG_SPL_OMAP3_ID_NAND -#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds" - -/* - * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM - * 64 bytes before this address should be set aside for u-boot.img's - * header. That is 0x800FFFC0--0x80100000 should not be used for any - * other needs. - */ -#define CONFIG_SYS_TEXT_BASE 0x80100000 -#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 - -/* ----------------------------------------------------------------------------- - * Default environment - * ----------------------------------------------------------------------------- - */ +/* Environment */ +#define CONFIG_PREBOOT "usb start" #define CONFIG_EXTRA_ENV_SETTINGS \ + DEFAULT_LINUX_BOOT_ENV \ + "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ + "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ "loadaddr=0x82000000\0" \ "usbtty=cdc_acm\0" \ "mmcdev=0\0" \ "console=ttyO0,115200n8\0" \ "mmcargs=setenv bootargs console=${console} " \ + "${optargs} " \ "root=/dev/mmcblk0p2 rw " \ - "rootfstype=ext3 rootwait\0" \ + "rootfstype=ext4 rootwait\0" \ "nandargs=setenv bootargs console=${console} " \ - "root=/dev/mtdblock4 rw " \ - "rootfstype=jffs2\0" \ + "${optargs} " \ + "root=ubi0:rootfs rw ubi.mtd=rootfs noinitrd " \ + "rootfstype=ubifs rootwait\0" \ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source ${loadaddr}\0" \ - "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ - "mmcboot=echo Booting from mmc ...; " \ + "loaduimage=setenv bootfile uImage; " \ + "fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ + "loadzimage=setenv bootfile zImage; " \ + "fatload mmc ${mmcdev} ${loadaddr} zImage\0" \ + "loaddtb=fatload mmc ${mmcdev} ${fdtaddr} omap3-evm.dtb\0" \ + "mmcboot=echo Booting ${bootfile} from mmc ...; " \ + "run mmcargs; " \ + "bootm ${loadaddr} - ${fdtaddr}\0" \ + "mmcbootz=echo Booting ${bootfile} from mmc ...; " \ "run mmcargs; " \ - "bootm ${loadaddr}\0" \ - "nandboot=echo Booting from nand ...; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ + "nandboot=echo Booting uImage from nand ...; " \ "run nandargs; " \ - "onenand read ${loadaddr} 280000 400000; " \ - "bootm ${loadaddr}\0" \ + "nand read ${loadaddr} kernel; " \ + "nand read ${fdtaddr} dtb; " \ + "bootm ${loadaddr} - ${fdtaddr}\0" #define CONFIG_BOOTCOMMAND \ "mmc dev ${mmcdev}; if mmc rescan; then " \ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "else run nandboot; " \ - "fi; " \ + "if run loadzimage && run loaddtb; then " \ + "run mmcbootz; fi; " \ + "if run loaduimage && run loaddtb; then " \ + "run mmcboot; fi; " \ + "run nandboot; " \ "fi; " \ "else run nandboot; fi" -#endif /* __OMAP3EVM_CONFIG_H */ +#endif /* __CONFIG_H */ -- cgit v0.10.2