From 3abfd887e820010d73839263e49849dcefc9b59e Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Fri, 28 Apr 2017 19:42:18 +0900 Subject: ARM: sunxi: move board/sunxi/Kconfig to arch/arm/mach-sunxi/Kconfig For the consistent location of SoC-level Kconfig. Signed-off-by: Masahiro Yamada Signed-off-by: Maxime Ripard diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 42f93b4..07fd1e0 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1226,6 +1226,8 @@ source "arch/arm/mach-sti/Kconfig" source "arch/arm/mach-stm32/Kconfig" +source "arch/arm/mach-sunxi/Kconfig" + source "arch/arm/mach-tegra/Kconfig" source "arch/arm/mach-uniphier/Kconfig" @@ -1311,7 +1313,6 @@ source "board/spear/spear320/Kconfig" source "board/spear/spear600/Kconfig" source "board/spear/x600/Kconfig" source "board/st/stv0991/Kconfig" -source "board/sunxi/Kconfig" source "board/syteco/zmx25/Kconfig" source "board/tcl/sl50/Kconfig" source "board/ti/am335x/Kconfig" diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig new file mode 100644 index 0000000..ac3be30 --- /dev/null +++ b/arch/arm/mach-sunxi/Kconfig @@ -0,0 +1,792 @@ +if ARCH_SUNXI + +config IDENT_STRING + default " Allwinner Technology" + +# FIXME: Should not redefine these Kconfig symbols +config PRE_CONSOLE_BUFFER + default y + +config SPL_GPIO_SUPPORT + default y + +config SPL_LIBCOMMON_SUPPORT + default y + +config SPL_LIBDISK_SUPPORT + default y + +config SPL_LIBGENERIC_SUPPORT + default y + +config SPL_MMC_SUPPORT + depends on SPL && GENERIC_MMC + default y + +config SPL_POWER_SUPPORT + default y + +config SPL_SERIAL_SUPPORT + default y + +config SUNXI_HIGH_SRAM + bool + default n + ---help--- + Older Allwinner SoCs have their mask boot ROM mapped just below 4GB, + with the first SRAM region being located at address 0. + Some newer SoCs map the boot ROM at address 0 instead and move the + SRAM to 64KB, just behind the mask ROM. + Chips using the latter setup are supposed to select this option to + adjust the addresses accordingly. + +# Note only one of these may be selected at a time! But hidden choices are +# not supported by Kconfig +config SUNXI_GEN_SUN4I + bool + ---help--- + Select this for sunxi SoCs which have resets and clocks set up + as the original A10 (mach-sun4i). + +config SUNXI_GEN_SUN6I + bool + ---help--- + Select this for sunxi SoCs which have sun6i like periphery, like + separate ahb reset control registers, custom pmic bus, new style + watchdog, etc. + + +config MACH_SUNXI_H3_H5 + bool + select DM_I2C + select SUNXI_DE2 + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + +choice + prompt "Sunxi SoC Variant" + optional + +config MACH_SUN4I + bool "sun4i (Allwinner A10)" + select CPU_V7 + select ARM_CORTEX_CPU_IS_UP + select SUNXI_GEN_SUN4I + select SUPPORT_SPL + +config MACH_SUN5I + bool "sun5i (Allwinner A13)" + select CPU_V7 + select ARM_CORTEX_CPU_IS_UP + select SUNXI_GEN_SUN4I + select SUPPORT_SPL + +config MACH_SUN6I + bool "sun6i (Allwinner A31)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN7I + bool "sun7i (Allwinner A20)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select SUNXI_GEN_SUN4I + select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN8I_A23 + bool "sun8i (Allwinner A23)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN8I_A33 + bool "sun8i (Allwinner A33)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN8I_A83T + bool "sun8i (Allwinner A83T)" + select CPU_V7 + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + +config MACH_SUN8I_H3 + bool "sun8i (Allwinner H3)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select MACH_SUNXI_H3_H5 + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN8I_R40 + bool "sun8i (Allwinner R40)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + +config MACH_SUN8I_V3S + bool "sun8i (Allwinner V3s)" + select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI + select SUNXI_GEN_SUN6I + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN9I + bool "sun9i (Allwinner A80)" + select CPU_V7 + select SUNXI_HIGH_SRAM + select SUNXI_GEN_SUN6I + select SUPPORT_SPL + +config MACH_SUN50I + bool "sun50i (Allwinner A64)" + select ARM64 + select DM_I2C + select SUNXI_DE2 + select SUNXI_GEN_SUN6I + select SUNXI_HIGH_SRAM + select SUPPORT_SPL + +config MACH_SUN50I_H5 + bool "sun50i (Allwinner H5)" + select ARM64 + select MACH_SUNXI_H3_H5 + select SUNXI_HIGH_SRAM + +endchoice + +# The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" +config MACH_SUN8I + bool + default y if MACH_SUN8I_A23 + default y if MACH_SUN8I_A33 + default y if MACH_SUN8I_A83T + default y if MACH_SUNXI_H3_H5 + default y if MACH_SUN8I_R40 + default y if MACH_SUN8I_V3S + +config RESERVE_ALLWINNER_BOOT0_HEADER + bool "reserve space for Allwinner boot0 header" + select ENABLE_ARM_SOC_BOOT0_HOOK + ---help--- + Prepend a 1536 byte (empty) header to the U-Boot image file, to be + filled with magic values post build. The Allwinner provided boot0 + blob relies on this information to load and execute U-Boot. + Only needed on 64-bit Allwinner boards so far when using boot0. + +config ARM_BOOT_HOOK_RMR + bool + depends on ARM64 + default y + select ENABLE_ARM_SOC_BOOT0_HOOK + ---help--- + Insert some ARM32 code at the very beginning of the U-Boot binary + which uses an RMR register write to bring the core into AArch64 mode. + The very first instruction acts as a switch, since it's carefully + chosen to be a NOP in one mode and a branch in the other, so the + code would only be executed if not already in AArch64. + This allows both the SPL and the U-Boot proper to be entered in + either mode and switch to AArch64 if needed. + +config DRAM_TYPE + int "sunxi dram type" + depends on MACH_SUN8I_A83T + default 3 + ---help--- + Set the dram type, 3: DDR3, 7: LPDDR3 + +config DRAM_CLK + int "sunxi dram clock speed" + default 792 if MACH_SUN9I + default 648 if MACH_SUN8I_R40 + default 312 if MACH_SUN6I || MACH_SUN8I + default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I + default 672 if MACH_SUN50I + ---help--- + Set the dram clock speed, valid range 240 - 480 (prior to sun9i), + must be a multiple of 24. For the sun9i (A80), the tested values + (for DDR3-1600) are 312 to 792. + +if MACH_SUN5I || MACH_SUN7I +config DRAM_MBUS_CLK + int "sunxi mbus clock speed" + default 300 + ---help--- + Set the mbus clock speed. The maximum on sun5i hardware is 300MHz. + +endif + +config DRAM_ZQ + int "sunxi dram zq value" + default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I + default 127 if MACH_SUN7I + default 3881979 if MACH_SUN8I_R40 + default 4145117 if MACH_SUN9I + default 3881915 if MACH_SUN50I + ---help--- + Set the dram zq value. + +config DRAM_ODT_EN + bool "sunxi dram odt enable" + default n if !MACH_SUN8I_A23 + default y if MACH_SUN8I_A23 + default y if MACH_SUN8I_R40 + default y if MACH_SUN50I + ---help--- + Select this to enable dram odt (on die termination). + +if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I +config DRAM_EMR1 + int "sunxi dram emr1 value" + default 0 if MACH_SUN4I + default 4 if MACH_SUN5I || MACH_SUN7I + ---help--- + Set the dram controller emr1 value. + +config DRAM_TPR3 + hex "sunxi dram tpr3 value" + default 0 + ---help--- + Set the dram controller tpr3 parameter. This parameter configures + the delay on the command lane and also phase shifts, which are + applied for sampling incoming read data. The default value 0 + means that no phase/delay adjustments are necessary. Properly + configuring this parameter increases reliability at high DRAM + clock speeds. + +config DRAM_DQS_GATING_DELAY + hex "sunxi dram dqs_gating_delay value" + default 0 + ---help--- + Set the dram controller dqs_gating_delay parmeter. Each byte + encodes the DQS gating delay for each byte lane. The delay + granularity is 1/4 cycle. For example, the value 0x05060606 + means that the delay is 5 quarter-cycles for one lane (1.25 + cycles) and 6 quarter-cycles (1.5 cycles) for 3 other lanes. + The default value 0 means autodetection. The results of hardware + autodetection are not very reliable and depend on the chip + temperature (sometimes producing different results on cold start + and warm reboot). But the accuracy of hardware autodetection + is usually good enough, unless running at really high DRAM + clocks speeds (up to 600MHz). If unsure, keep as 0. + +choice + prompt "sunxi dram timings" + default DRAM_TIMINGS_VENDOR_MAGIC + ---help--- + Select the timings of the DDR3 chips. + +config DRAM_TIMINGS_VENDOR_MAGIC + bool "Magic vendor timings from Android" + ---help--- + The same DRAM timings as in the Allwinner boot0 bootloader. + +config DRAM_TIMINGS_DDR3_1066F_1333H + bool "JEDEC DDR3-1333H with down binning to DDR3-1066F" + ---help--- + Use the timings of the standard JEDEC DDR3-1066F speed bin for + DRAM_CLK <= 533MHz and the timings of the DDR3-1333H speed bin + for DRAM_CLK > 533MHz. This covers the majority of DDR3 chips + used in Allwinner A10/A13/A20 devices. In the case of DDR3-1333 + or DDR3-1600 chips, be sure to check the DRAM datasheet to confirm + that down binning to DDR3-1066F is supported (because DDR3-1066F + uses a bit faster timings than DDR3-1333H). + +config DRAM_TIMINGS_DDR3_800E_1066G_1333J + bool "JEDEC DDR3-800E / DDR3-1066G / DDR3-1333J" + ---help--- + Use the timings of the slowest possible JEDEC speed bin for the + selected DRAM_CLK. Depending on the DRAM_CLK value, it may be + DDR3-800E, DDR3-1066G or DDR3-1333J. + +endchoice + +endif + +if MACH_SUN8I_A23 +config DRAM_ODT_CORRECTION + int "sunxi dram odt correction value" + default 0 + ---help--- + Set the dram odt correction value (range -255 - 255). In allwinner + fex files, this option is found in bits 8-15 of the u32 odt_en variable + in the [dram] section. When bit 31 of the odt_en variable is set + then the correction is negative. Usually the value for this is 0. +endif + +config SYS_CLK_FREQ + default 1008000000 if MACH_SUN4I + default 1008000000 if MACH_SUN5I + default 1008000000 if MACH_SUN6I + default 912000000 if MACH_SUN7I + default 1008000000 if MACH_SUN8I + default 1008000000 if MACH_SUN9I + default 816000000 if MACH_SUN50I + +config SYS_CONFIG_NAME + default "sun4i" if MACH_SUN4I + default "sun5i" if MACH_SUN5I + default "sun6i" if MACH_SUN6I + default "sun7i" if MACH_SUN7I + default "sun8i" if MACH_SUN8I + default "sun9i" if MACH_SUN9I + default "sun50i" if MACH_SUN50I + +config SYS_BOARD + default "sunxi" + +config SYS_SOC + default "sunxi" + +config UART0_PORT_F + bool "UART0 on MicroSD breakout board" + default n + ---help--- + Repurpose the SD card slot for getting access to the UART0 serial + console. Primarily useful only for low level u-boot debugging on + tablets, where normal UART0 is difficult to access and requires + device disassembly and/or soldering. As the SD card can't be used + at the same time, the system can be only booted in the FEL mode. + Only enable this if you really know what you are doing. + +config OLD_SUNXI_KERNEL_COMPAT + bool "Enable workarounds for booting old kernels" + default n + ---help--- + Set this to enable various workarounds for old kernels, this results in + sub-optimal settings for newer kernels, only enable if needed. + +config MACPWR + string "MAC power pin" + default "" + help + Set the pin used to power the MAC. This takes a string in the format + understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config MMC0_CD_PIN + string "Card detect pin for mmc0" + default "PF6" if MACH_SUN8I_A83T || MACH_SUNXI_H3_H5 || MACH_SUN50I + default "" + ---help--- + Set the card detect pin for mmc0, leave empty to not use cd. This + takes a string in the format understood by sunxi_name_to_gpio, e.g. + PH1 for pin 1 of port H. + +config MMC1_CD_PIN + string "Card detect pin for mmc1" + default "" + ---help--- + See MMC0_CD_PIN help text. + +config MMC2_CD_PIN + string "Card detect pin for mmc2" + default "" + ---help--- + See MMC0_CD_PIN help text. + +config MMC3_CD_PIN + string "Card detect pin for mmc3" + default "" + ---help--- + See MMC0_CD_PIN help text. + +config MMC1_PINS + string "Pins for mmc1" + default "" + ---help--- + Set the pins used for mmc1, when applicable. This takes a string in the + format understood by sunxi_name_to_gpio_bank, e.g. PH for port H. + +config MMC2_PINS + string "Pins for mmc2" + default "" + ---help--- + See MMC1_PINS help text. + +config MMC3_PINS + string "Pins for mmc3" + default "" + ---help--- + See MMC1_PINS help text. + +config MMC_SUNXI_SLOT_EXTRA + int "mmc extra slot number" + default -1 + ---help--- + sunxi builds always enable mmc0, some boards also have a second sdcard + slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable + support for this. + +config INITIAL_USB_SCAN_DELAY + int "delay initial usb scan by x ms to allow builtin devices to init" + default 0 + ---help--- + Some boards have on board usb devices which need longer than the + USB spec's 1 second to connect from board powerup. Set this config + option to a non 0 value to add an extra delay before the first usb + bus scan. + +config USB0_VBUS_PIN + string "Vbus enable pin for usb0 (otg)" + default "" + ---help--- + Set the Vbus enable pin for usb0 (otg). This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config USB0_VBUS_DET + string "Vbus detect pin for usb0 (otg)" + default "" + ---help--- + Set the Vbus detect pin for usb0 (otg). This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config USB0_ID_DET + string "ID detect pin for usb0 (otg)" + default "" + ---help--- + Set the ID detect pin for usb0 (otg). This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config USB1_VBUS_PIN + string "Vbus enable pin for usb1 (ehci0)" + default "PH6" if MACH_SUN4I || MACH_SUN7I + default "PH27" if MACH_SUN6I + ---help--- + Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes + a string in the format understood by sunxi_name_to_gpio, e.g. + PH1 for pin 1 of port H. + +config USB2_VBUS_PIN + string "Vbus enable pin for usb2 (ehci1)" + default "PH3" if MACH_SUN4I || MACH_SUN7I + default "PH24" if MACH_SUN6I + ---help--- + See USB1_VBUS_PIN help text. + +config USB3_VBUS_PIN + string "Vbus enable pin for usb3 (ehci2)" + default "" + ---help--- + See USB1_VBUS_PIN help text. + +config I2C0_ENABLE + bool "Enable I2C/TWI controller 0" + default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40 + default n if MACH_SUN6I || MACH_SUN8I + select CMD_I2C + ---help--- + This allows enabling I2C/TWI controller 0 by muxing its pins, enabling + its clock and setting up the bus. This is especially useful on devices + with slaves connected to the bus or with pins exposed through e.g. an + expansion port/header. + +config I2C1_ENABLE + bool "Enable I2C/TWI controller 1" + default n + select CMD_I2C + ---help--- + See I2C0_ENABLE help text. + +config I2C2_ENABLE + bool "Enable I2C/TWI controller 2" + default n + select CMD_I2C + ---help--- + See I2C0_ENABLE help text. + +if MACH_SUN6I || MACH_SUN7I +config I2C3_ENABLE + bool "Enable I2C/TWI controller 3" + default n + select CMD_I2C + ---help--- + See I2C0_ENABLE help text. +endif + +if SUNXI_GEN_SUN6I +config R_I2C_ENABLE + bool "Enable the PRCM I2C/TWI controller" + # This is used for the pmic on H3 + default y if SY8106A_POWER + select CMD_I2C + ---help--- + Set this to y to enable the I2C controller which is part of the PRCM. +endif + +if MACH_SUN7I +config I2C4_ENABLE + bool "Enable I2C/TWI controller 4" + default n + select CMD_I2C + ---help--- + See I2C0_ENABLE help text. +endif + +config AXP_GPIO + bool "Enable support for gpio-s on axp PMICs" + default n + ---help--- + Say Y here to enable support for the gpio pins of the axp PMIC ICs. + +config VIDEO + bool "Enable graphical uboot console on HDMI, LCD or VGA" + depends on !MACH_SUN8I_A83T + depends on !MACH_SUNXI_H3_H5 + depends on !MACH_SUN8I_R40 + depends on !MACH_SUN8I_V3S + depends on !MACH_SUN9I + depends on !MACH_SUN50I + default y + ---help--- + Say Y here to add support for using a cfb console on the HDMI, LCD + or VGA output found on most sunxi devices. See doc/README.video for + info on how to select the video output and mode. + +config VIDEO_HDMI + bool "HDMI output support" + depends on VIDEO && !MACH_SUN8I + default y + ---help--- + Say Y here to add support for outputting video over HDMI. + +config VIDEO_VGA + bool "VGA output support" + depends on VIDEO && (MACH_SUN4I || MACH_SUN7I) + default n + ---help--- + Say Y here to add support for outputting video over VGA. + +config VIDEO_VGA_VIA_LCD + bool "VGA via LCD controller support" + depends on VIDEO && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I) + default n + ---help--- + Say Y here to add support for external DACs connected to the parallel + LCD interface driving a VGA connector, such as found on the + Olimex A13 boards. + +config VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH + bool "Force sync active high for VGA via LCD controller support" + depends on VIDEO_VGA_VIA_LCD + default n + ---help--- + Say Y here if you've a board which uses opendrain drivers for the vga + hsync and vsync signals. Opendrain drivers cannot generate steep enough + positive edges for a stable video output, so on boards with opendrain + drivers the sync signals must always be active high. + +config VIDEO_VGA_EXTERNAL_DAC_EN + string "LCD panel power enable pin" + depends on VIDEO_VGA_VIA_LCD + default "" + ---help--- + Set the enable pin for the external VGA DAC. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_COMPOSITE + bool "Composite video output support" + depends on VIDEO && (MACH_SUN4I || MACH_SUN5I || MACH_SUN7I) + default n + ---help--- + Say Y here to add support for outputting composite video. + +config VIDEO_LCD_MODE + string "LCD panel timing details" + depends on VIDEO + default "" + ---help--- + LCD panel timing details string, leave empty if there is no LCD panel. + This is in drivers/video/videomodes.c: video_get_params() format, e.g. + x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0 + Also see: http://linux-sunxi.org/LCD + +config VIDEO_LCD_DCLK_PHASE + int "LCD panel display clock phase" + depends on VIDEO + default 1 + ---help--- + Select LCD panel display clock phase shift, range 0-3. + +config VIDEO_LCD_POWER + string "LCD panel power enable pin" + depends on VIDEO + default "" + ---help--- + Set the power enable pin for the LCD panel. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_LCD_RESET + string "LCD panel reset pin" + depends on VIDEO + default "" + ---help--- + Set the reset pin for the LCD panel. This takes a string in the format + understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_LCD_BL_EN + string "LCD panel backlight enable pin" + depends on VIDEO + default "" + ---help--- + Set the backlight enable pin for the LCD panel. This takes a string in the + the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of + port H. + +config VIDEO_LCD_BL_PWM + string "LCD panel backlight pwm pin" + depends on VIDEO + default "" + ---help--- + Set the backlight pwm pin for the LCD panel. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_LCD_BL_PWM_ACTIVE_LOW + bool "LCD panel backlight pwm is inverted" + depends on VIDEO + default y + ---help--- + Set this if the backlight pwm output is active low. + +config VIDEO_LCD_PANEL_I2C + bool "LCD panel needs to be configured via i2c" + depends on VIDEO + default n + select CMD_I2C + ---help--- + Say y here if the LCD panel needs to be configured via i2c. This + will add a bitbang i2c controller using gpios to talk to the LCD. + +config VIDEO_LCD_PANEL_I2C_SDA + string "LCD panel i2c interface SDA pin" + depends on VIDEO_LCD_PANEL_I2C + default "PG12" + ---help--- + Set the SDA pin for the LCD i2c interface. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_LCD_PANEL_I2C_SCL + string "LCD panel i2c interface SCL pin" + depends on VIDEO_LCD_PANEL_I2C + default "PG10" + ---help--- + Set the SCL pin for the LCD i2c interface. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + + +# Note only one of these may be selected at a time! But hidden choices are +# not supported by Kconfig +config VIDEO_LCD_IF_PARALLEL + bool + +config VIDEO_LCD_IF_LVDS + bool + +config SUNXI_DE2 + bool + default n + +config VIDEO_DE2 + bool "Display Engine 2 video driver" + depends on SUNXI_DE2 + select DM_VIDEO + select DISPLAY + default y + ---help--- + Say y here if you want to build DE2 video driver which is present on + newer SoCs. Currently only HDMI output is supported. + + +choice + prompt "LCD panel support" + depends on VIDEO + ---help--- + Select which type of LCD panel to support. + +config VIDEO_LCD_PANEL_PARALLEL + bool "Generic parallel interface LCD panel" + select VIDEO_LCD_IF_PARALLEL + +config VIDEO_LCD_PANEL_LVDS + bool "Generic lvds interface LCD panel" + select VIDEO_LCD_IF_LVDS + +config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828 + bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip" + select VIDEO_LCD_SSD2828 + select VIDEO_LCD_IF_PARALLEL + ---help--- + 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0 + +config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804 + bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip" + select VIDEO_LCD_ANX9804 + select VIDEO_LCD_IF_PARALLEL + select VIDEO_LCD_PANEL_I2C + ---help--- + Select this for eDP LCD panels with 4 lanes running at 1.62G, + connected via an ANX9804 bridge chip. + +config VIDEO_LCD_PANEL_HITACHI_TX18D42VM + bool "Hitachi tx18d42vm LCD panel" + select VIDEO_LCD_HITACHI_TX18D42VM + select VIDEO_LCD_IF_LVDS + ---help--- + 7.85" 1024x768 Hitachi tx18d42vm LCD panel support + +config VIDEO_LCD_TL059WV5C0 + bool "tl059wv5c0 LCD panel" + select VIDEO_LCD_PANEL_I2C + select VIDEO_LCD_IF_PARALLEL + ---help--- + 6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and + Aigo M60/M608/M606 tablets. + +endchoice + +config SATAPWR + string "SATA power pin" + default "" + help + Set the pins used to power the SATA. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of + port H. + +config GMAC_TX_DELAY + int "GMAC Transmit Clock Delay Chain" + default 0 + ---help--- + Set the GMAC Transmit Clock Delay Chain value. + +config SPL_STACK_R_ADDR + default 0x4fe00000 if MACH_SUN4I + default 0x4fe00000 if MACH_SUN5I + default 0x4fe00000 if MACH_SUN6I + default 0x4fe00000 if MACH_SUN7I + default 0x4fe00000 if MACH_SUN8I + default 0x2fe00000 if MACH_SUN9I + default 0x4fe00000 if MACH_SUN50I + +endif diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig deleted file mode 100644 index ac3be30..0000000 --- a/board/sunxi/Kconfig +++ /dev/null @@ -1,792 +0,0 @@ -if ARCH_SUNXI - -config IDENT_STRING - default " Allwinner Technology" - -# FIXME: Should not redefine these Kconfig symbols -config PRE_CONSOLE_BUFFER - default y - -config SPL_GPIO_SUPPORT - default y - -config SPL_LIBCOMMON_SUPPORT - default y - -config SPL_LIBDISK_SUPPORT - default y - -config SPL_LIBGENERIC_SUPPORT - default y - -config SPL_MMC_SUPPORT - depends on SPL && GENERIC_MMC - default y - -config SPL_POWER_SUPPORT - default y - -config SPL_SERIAL_SUPPORT - default y - -config SUNXI_HIGH_SRAM - bool - default n - ---help--- - Older Allwinner SoCs have their mask boot ROM mapped just below 4GB, - with the first SRAM region being located at address 0. - Some newer SoCs map the boot ROM at address 0 instead and move the - SRAM to 64KB, just behind the mask ROM. - Chips using the latter setup are supposed to select this option to - adjust the addresses accordingly. - -# Note only one of these may be selected at a time! But hidden choices are -# not supported by Kconfig -config SUNXI_GEN_SUN4I - bool - ---help--- - Select this for sunxi SoCs which have resets and clocks set up - as the original A10 (mach-sun4i). - -config SUNXI_GEN_SUN6I - bool - ---help--- - Select this for sunxi SoCs which have sun6i like periphery, like - separate ahb reset control registers, custom pmic bus, new style - watchdog, etc. - - -config MACH_SUNXI_H3_H5 - bool - select DM_I2C - select SUNXI_DE2 - select SUNXI_GEN_SUN6I - select SUPPORT_SPL - -choice - prompt "Sunxi SoC Variant" - optional - -config MACH_SUN4I - bool "sun4i (Allwinner A10)" - select CPU_V7 - select ARM_CORTEX_CPU_IS_UP - select SUNXI_GEN_SUN4I - select SUPPORT_SPL - -config MACH_SUN5I - bool "sun5i (Allwinner A13)" - select CPU_V7 - select ARM_CORTEX_CPU_IS_UP - select SUNXI_GEN_SUN4I - select SUPPORT_SPL - -config MACH_SUN6I - bool "sun6i (Allwinner A31)" - select CPU_V7 - select CPU_V7_HAS_NONSEC - select CPU_V7_HAS_VIRT - select ARCH_SUPPORT_PSCI - select SUNXI_GEN_SUN6I - select SUPPORT_SPL - select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT - -config MACH_SUN7I - bool "sun7i (Allwinner A20)" - select CPU_V7 - select CPU_V7_HAS_NONSEC - select CPU_V7_HAS_VIRT - select ARCH_SUPPORT_PSCI - select SUNXI_GEN_SUN4I - select SUPPORT_SPL - select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT - -config MACH_SUN8I_A23 - bool "sun8i (Allwinner A23)" - select CPU_V7 - select CPU_V7_HAS_NONSEC - select CPU_V7_HAS_VIRT - select ARCH_SUPPORT_PSCI - select SUNXI_GEN_SUN6I - select SUPPORT_SPL - select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT - -config MACH_SUN8I_A33 - bool "sun8i (Allwinner A33)" - select CPU_V7 - select CPU_V7_HAS_NONSEC - select CPU_V7_HAS_VIRT - select ARCH_SUPPORT_PSCI - select SUNXI_GEN_SUN6I - select SUPPORT_SPL - select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT - -config MACH_SUN8I_A83T - bool "sun8i (Allwinner A83T)" - select CPU_V7 - select SUNXI_GEN_SUN6I - select SUPPORT_SPL - -config MACH_SUN8I_H3 - bool "sun8i (Allwinner H3)" - select CPU_V7 - select CPU_V7_HAS_NONSEC - select CPU_V7_HAS_VIRT - select ARCH_SUPPORT_PSCI - select MACH_SUNXI_H3_H5 - select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT - -config MACH_SUN8I_R40 - bool "sun8i (Allwinner R40)" - select CPU_V7 - select CPU_V7_HAS_NONSEC - select CPU_V7_HAS_VIRT - select ARCH_SUPPORT_PSCI - select SUNXI_GEN_SUN6I - select SUPPORT_SPL - -config MACH_SUN8I_V3S - bool "sun8i (Allwinner V3s)" - select CPU_V7 - select CPU_V7_HAS_NONSEC - select CPU_V7_HAS_VIRT - select ARCH_SUPPORT_PSCI - select SUNXI_GEN_SUN6I - select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT - -config MACH_SUN9I - bool "sun9i (Allwinner A80)" - select CPU_V7 - select SUNXI_HIGH_SRAM - select SUNXI_GEN_SUN6I - select SUPPORT_SPL - -config MACH_SUN50I - bool "sun50i (Allwinner A64)" - select ARM64 - select DM_I2C - select SUNXI_DE2 - select SUNXI_GEN_SUN6I - select SUNXI_HIGH_SRAM - select SUPPORT_SPL - -config MACH_SUN50I_H5 - bool "sun50i (Allwinner H5)" - select ARM64 - select MACH_SUNXI_H3_H5 - select SUNXI_HIGH_SRAM - -endchoice - -# The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" -config MACH_SUN8I - bool - default y if MACH_SUN8I_A23 - default y if MACH_SUN8I_A33 - default y if MACH_SUN8I_A83T - default y if MACH_SUNXI_H3_H5 - default y if MACH_SUN8I_R40 - default y if MACH_SUN8I_V3S - -config RESERVE_ALLWINNER_BOOT0_HEADER - bool "reserve space for Allwinner boot0 header" - select ENABLE_ARM_SOC_BOOT0_HOOK - ---help--- - Prepend a 1536 byte (empty) header to the U-Boot image file, to be - filled with magic values post build. The Allwinner provided boot0 - blob relies on this information to load and execute U-Boot. - Only needed on 64-bit Allwinner boards so far when using boot0. - -config ARM_BOOT_HOOK_RMR - bool - depends on ARM64 - default y - select ENABLE_ARM_SOC_BOOT0_HOOK - ---help--- - Insert some ARM32 code at the very beginning of the U-Boot binary - which uses an RMR register write to bring the core into AArch64 mode. - The very first instruction acts as a switch, since it's carefully - chosen to be a NOP in one mode and a branch in the other, so the - code would only be executed if not already in AArch64. - This allows both the SPL and the U-Boot proper to be entered in - either mode and switch to AArch64 if needed. - -config DRAM_TYPE - int "sunxi dram type" - depends on MACH_SUN8I_A83T - default 3 - ---help--- - Set the dram type, 3: DDR3, 7: LPDDR3 - -config DRAM_CLK - int "sunxi dram clock speed" - default 792 if MACH_SUN9I - default 648 if MACH_SUN8I_R40 - default 312 if MACH_SUN6I || MACH_SUN8I - default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I - default 672 if MACH_SUN50I - ---help--- - Set the dram clock speed, valid range 240 - 480 (prior to sun9i), - must be a multiple of 24. For the sun9i (A80), the tested values - (for DDR3-1600) are 312 to 792. - -if MACH_SUN5I || MACH_SUN7I -config DRAM_MBUS_CLK - int "sunxi mbus clock speed" - default 300 - ---help--- - Set the mbus clock speed. The maximum on sun5i hardware is 300MHz. - -endif - -config DRAM_ZQ - int "sunxi dram zq value" - default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I - default 127 if MACH_SUN7I - default 3881979 if MACH_SUN8I_R40 - default 4145117 if MACH_SUN9I - default 3881915 if MACH_SUN50I - ---help--- - Set the dram zq value. - -config DRAM_ODT_EN - bool "sunxi dram odt enable" - default n if !MACH_SUN8I_A23 - default y if MACH_SUN8I_A23 - default y if MACH_SUN8I_R40 - default y if MACH_SUN50I - ---help--- - Select this to enable dram odt (on die termination). - -if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I -config DRAM_EMR1 - int "sunxi dram emr1 value" - default 0 if MACH_SUN4I - default 4 if MACH_SUN5I || MACH_SUN7I - ---help--- - Set the dram controller emr1 value. - -config DRAM_TPR3 - hex "sunxi dram tpr3 value" - default 0 - ---help--- - Set the dram controller tpr3 parameter. This parameter configures - the delay on the command lane and also phase shifts, which are - applied for sampling incoming read data. The default value 0 - means that no phase/delay adjustments are necessary. Properly - configuring this parameter increases reliability at high DRAM - clock speeds. - -config DRAM_DQS_GATING_DELAY - hex "sunxi dram dqs_gating_delay value" - default 0 - ---help--- - Set the dram controller dqs_gating_delay parmeter. Each byte - encodes the DQS gating delay for each byte lane. The delay - granularity is 1/4 cycle. For example, the value 0x05060606 - means that the delay is 5 quarter-cycles for one lane (1.25 - cycles) and 6 quarter-cycles (1.5 cycles) for 3 other lanes. - The default value 0 means autodetection. The results of hardware - autodetection are not very reliable and depend on the chip - temperature (sometimes producing different results on cold start - and warm reboot). But the accuracy of hardware autodetection - is usually good enough, unless running at really high DRAM - clocks speeds (up to 600MHz). If unsure, keep as 0. - -choice - prompt "sunxi dram timings" - default DRAM_TIMINGS_VENDOR_MAGIC - ---help--- - Select the timings of the DDR3 chips. - -config DRAM_TIMINGS_VENDOR_MAGIC - bool "Magic vendor timings from Android" - ---help--- - The same DRAM timings as in the Allwinner boot0 bootloader. - -config DRAM_TIMINGS_DDR3_1066F_1333H - bool "JEDEC DDR3-1333H with down binning to DDR3-1066F" - ---help--- - Use the timings of the standard JEDEC DDR3-1066F speed bin for - DRAM_CLK <= 533MHz and the timings of the DDR3-1333H speed bin - for DRAM_CLK > 533MHz. This covers the majority of DDR3 chips - used in Allwinner A10/A13/A20 devices. In the case of DDR3-1333 - or DDR3-1600 chips, be sure to check the DRAM datasheet to confirm - that down binning to DDR3-1066F is supported (because DDR3-1066F - uses a bit faster timings than DDR3-1333H). - -config DRAM_TIMINGS_DDR3_800E_1066G_1333J - bool "JEDEC DDR3-800E / DDR3-1066G / DDR3-1333J" - ---help--- - Use the timings of the slowest possible JEDEC speed bin for the - selected DRAM_CLK. Depending on the DRAM_CLK value, it may be - DDR3-800E, DDR3-1066G or DDR3-1333J. - -endchoice - -endif - -if MACH_SUN8I_A23 -config DRAM_ODT_CORRECTION - int "sunxi dram odt correction value" - default 0 - ---help--- - Set the dram odt correction value (range -255 - 255). In allwinner - fex files, this option is found in bits 8-15 of the u32 odt_en variable - in the [dram] section. When bit 31 of the odt_en variable is set - then the correction is negative. Usually the value for this is 0. -endif - -config SYS_CLK_FREQ - default 1008000000 if MACH_SUN4I - default 1008000000 if MACH_SUN5I - default 1008000000 if MACH_SUN6I - default 912000000 if MACH_SUN7I - default 1008000000 if MACH_SUN8I - default 1008000000 if MACH_SUN9I - default 816000000 if MACH_SUN50I - -config SYS_CONFIG_NAME - default "sun4i" if MACH_SUN4I - default "sun5i" if MACH_SUN5I - default "sun6i" if MACH_SUN6I - default "sun7i" if MACH_SUN7I - default "sun8i" if MACH_SUN8I - default "sun9i" if MACH_SUN9I - default "sun50i" if MACH_SUN50I - -config SYS_BOARD - default "sunxi" - -config SYS_SOC - default "sunxi" - -config UART0_PORT_F - bool "UART0 on MicroSD breakout board" - default n - ---help--- - Repurpose the SD card slot for getting access to the UART0 serial - console. Primarily useful only for low level u-boot debugging on - tablets, where normal UART0 is difficult to access and requires - device disassembly and/or soldering. As the SD card can't be used - at the same time, the system can be only booted in the FEL mode. - Only enable this if you really know what you are doing. - -config OLD_SUNXI_KERNEL_COMPAT - bool "Enable workarounds for booting old kernels" - default n - ---help--- - Set this to enable various workarounds for old kernels, this results in - sub-optimal settings for newer kernels, only enable if needed. - -config MACPWR - string "MAC power pin" - default "" - help - Set the pin used to power the MAC. This takes a string in the format - understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config MMC0_CD_PIN - string "Card detect pin for mmc0" - default "PF6" if MACH_SUN8I_A83T || MACH_SUNXI_H3_H5 || MACH_SUN50I - default "" - ---help--- - Set the card detect pin for mmc0, leave empty to not use cd. This - takes a string in the format understood by sunxi_name_to_gpio, e.g. - PH1 for pin 1 of port H. - -config MMC1_CD_PIN - string "Card detect pin for mmc1" - default "" - ---help--- - See MMC0_CD_PIN help text. - -config MMC2_CD_PIN - string "Card detect pin for mmc2" - default "" - ---help--- - See MMC0_CD_PIN help text. - -config MMC3_CD_PIN - string "Card detect pin for mmc3" - default "" - ---help--- - See MMC0_CD_PIN help text. - -config MMC1_PINS - string "Pins for mmc1" - default "" - ---help--- - Set the pins used for mmc1, when applicable. This takes a string in the - format understood by sunxi_name_to_gpio_bank, e.g. PH for port H. - -config MMC2_PINS - string "Pins for mmc2" - default "" - ---help--- - See MMC1_PINS help text. - -config MMC3_PINS - string "Pins for mmc3" - default "" - ---help--- - See MMC1_PINS help text. - -config MMC_SUNXI_SLOT_EXTRA - int "mmc extra slot number" - default -1 - ---help--- - sunxi builds always enable mmc0, some boards also have a second sdcard - slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable - support for this. - -config INITIAL_USB_SCAN_DELAY - int "delay initial usb scan by x ms to allow builtin devices to init" - default 0 - ---help--- - Some boards have on board usb devices which need longer than the - USB spec's 1 second to connect from board powerup. Set this config - option to a non 0 value to add an extra delay before the first usb - bus scan. - -config USB0_VBUS_PIN - string "Vbus enable pin for usb0 (otg)" - default "" - ---help--- - Set the Vbus enable pin for usb0 (otg). This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config USB0_VBUS_DET - string "Vbus detect pin for usb0 (otg)" - default "" - ---help--- - Set the Vbus detect pin for usb0 (otg). This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config USB0_ID_DET - string "ID detect pin for usb0 (otg)" - default "" - ---help--- - Set the ID detect pin for usb0 (otg). This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config USB1_VBUS_PIN - string "Vbus enable pin for usb1 (ehci0)" - default "PH6" if MACH_SUN4I || MACH_SUN7I - default "PH27" if MACH_SUN6I - ---help--- - Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes - a string in the format understood by sunxi_name_to_gpio, e.g. - PH1 for pin 1 of port H. - -config USB2_VBUS_PIN - string "Vbus enable pin for usb2 (ehci1)" - default "PH3" if MACH_SUN4I || MACH_SUN7I - default "PH24" if MACH_SUN6I - ---help--- - See USB1_VBUS_PIN help text. - -config USB3_VBUS_PIN - string "Vbus enable pin for usb3 (ehci2)" - default "" - ---help--- - See USB1_VBUS_PIN help text. - -config I2C0_ENABLE - bool "Enable I2C/TWI controller 0" - default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40 - default n if MACH_SUN6I || MACH_SUN8I - select CMD_I2C - ---help--- - This allows enabling I2C/TWI controller 0 by muxing its pins, enabling - its clock and setting up the bus. This is especially useful on devices - with slaves connected to the bus or with pins exposed through e.g. an - expansion port/header. - -config I2C1_ENABLE - bool "Enable I2C/TWI controller 1" - default n - select CMD_I2C - ---help--- - See I2C0_ENABLE help text. - -config I2C2_ENABLE - bool "Enable I2C/TWI controller 2" - default n - select CMD_I2C - ---help--- - See I2C0_ENABLE help text. - -if MACH_SUN6I || MACH_SUN7I -config I2C3_ENABLE - bool "Enable I2C/TWI controller 3" - default n - select CMD_I2C - ---help--- - See I2C0_ENABLE help text. -endif - -if SUNXI_GEN_SUN6I -config R_I2C_ENABLE - bool "Enable the PRCM I2C/TWI controller" - # This is used for the pmic on H3 - default y if SY8106A_POWER - select CMD_I2C - ---help--- - Set this to y to enable the I2C controller which is part of the PRCM. -endif - -if MACH_SUN7I -config I2C4_ENABLE - bool "Enable I2C/TWI controller 4" - default n - select CMD_I2C - ---help--- - See I2C0_ENABLE help text. -endif - -config AXP_GPIO - bool "Enable support for gpio-s on axp PMICs" - default n - ---help--- - Say Y here to enable support for the gpio pins of the axp PMIC ICs. - -config VIDEO - bool "Enable graphical uboot console on HDMI, LCD or VGA" - depends on !MACH_SUN8I_A83T - depends on !MACH_SUNXI_H3_H5 - depends on !MACH_SUN8I_R40 - depends on !MACH_SUN8I_V3S - depends on !MACH_SUN9I - depends on !MACH_SUN50I - default y - ---help--- - Say Y here to add support for using a cfb console on the HDMI, LCD - or VGA output found on most sunxi devices. See doc/README.video for - info on how to select the video output and mode. - -config VIDEO_HDMI - bool "HDMI output support" - depends on VIDEO && !MACH_SUN8I - default y - ---help--- - Say Y here to add support for outputting video over HDMI. - -config VIDEO_VGA - bool "VGA output support" - depends on VIDEO && (MACH_SUN4I || MACH_SUN7I) - default n - ---help--- - Say Y here to add support for outputting video over VGA. - -config VIDEO_VGA_VIA_LCD - bool "VGA via LCD controller support" - depends on VIDEO && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I) - default n - ---help--- - Say Y here to add support for external DACs connected to the parallel - LCD interface driving a VGA connector, such as found on the - Olimex A13 boards. - -config VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH - bool "Force sync active high for VGA via LCD controller support" - depends on VIDEO_VGA_VIA_LCD - default n - ---help--- - Say Y here if you've a board which uses opendrain drivers for the vga - hsync and vsync signals. Opendrain drivers cannot generate steep enough - positive edges for a stable video output, so on boards with opendrain - drivers the sync signals must always be active high. - -config VIDEO_VGA_EXTERNAL_DAC_EN - string "LCD panel power enable pin" - depends on VIDEO_VGA_VIA_LCD - default "" - ---help--- - Set the enable pin for the external VGA DAC. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config VIDEO_COMPOSITE - bool "Composite video output support" - depends on VIDEO && (MACH_SUN4I || MACH_SUN5I || MACH_SUN7I) - default n - ---help--- - Say Y here to add support for outputting composite video. - -config VIDEO_LCD_MODE - string "LCD panel timing details" - depends on VIDEO - default "" - ---help--- - LCD panel timing details string, leave empty if there is no LCD panel. - This is in drivers/video/videomodes.c: video_get_params() format, e.g. - x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0 - Also see: http://linux-sunxi.org/LCD - -config VIDEO_LCD_DCLK_PHASE - int "LCD panel display clock phase" - depends on VIDEO - default 1 - ---help--- - Select LCD panel display clock phase shift, range 0-3. - -config VIDEO_LCD_POWER - string "LCD panel power enable pin" - depends on VIDEO - default "" - ---help--- - Set the power enable pin for the LCD panel. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config VIDEO_LCD_RESET - string "LCD panel reset pin" - depends on VIDEO - default "" - ---help--- - Set the reset pin for the LCD panel. This takes a string in the format - understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config VIDEO_LCD_BL_EN - string "LCD panel backlight enable pin" - depends on VIDEO - default "" - ---help--- - Set the backlight enable pin for the LCD panel. This takes a string in the - the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of - port H. - -config VIDEO_LCD_BL_PWM - string "LCD panel backlight pwm pin" - depends on VIDEO - default "" - ---help--- - Set the backlight pwm pin for the LCD panel. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config VIDEO_LCD_BL_PWM_ACTIVE_LOW - bool "LCD panel backlight pwm is inverted" - depends on VIDEO - default y - ---help--- - Set this if the backlight pwm output is active low. - -config VIDEO_LCD_PANEL_I2C - bool "LCD panel needs to be configured via i2c" - depends on VIDEO - default n - select CMD_I2C - ---help--- - Say y here if the LCD panel needs to be configured via i2c. This - will add a bitbang i2c controller using gpios to talk to the LCD. - -config VIDEO_LCD_PANEL_I2C_SDA - string "LCD panel i2c interface SDA pin" - depends on VIDEO_LCD_PANEL_I2C - default "PG12" - ---help--- - Set the SDA pin for the LCD i2c interface. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config VIDEO_LCD_PANEL_I2C_SCL - string "LCD panel i2c interface SCL pin" - depends on VIDEO_LCD_PANEL_I2C - default "PG10" - ---help--- - Set the SCL pin for the LCD i2c interface. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - - -# Note only one of these may be selected at a time! But hidden choices are -# not supported by Kconfig -config VIDEO_LCD_IF_PARALLEL - bool - -config VIDEO_LCD_IF_LVDS - bool - -config SUNXI_DE2 - bool - default n - -config VIDEO_DE2 - bool "Display Engine 2 video driver" - depends on SUNXI_DE2 - select DM_VIDEO - select DISPLAY - default y - ---help--- - Say y here if you want to build DE2 video driver which is present on - newer SoCs. Currently only HDMI output is supported. - - -choice - prompt "LCD panel support" - depends on VIDEO - ---help--- - Select which type of LCD panel to support. - -config VIDEO_LCD_PANEL_PARALLEL - bool "Generic parallel interface LCD panel" - select VIDEO_LCD_IF_PARALLEL - -config VIDEO_LCD_PANEL_LVDS - bool "Generic lvds interface LCD panel" - select VIDEO_LCD_IF_LVDS - -config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828 - bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip" - select VIDEO_LCD_SSD2828 - select VIDEO_LCD_IF_PARALLEL - ---help--- - 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0 - -config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804 - bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip" - select VIDEO_LCD_ANX9804 - select VIDEO_LCD_IF_PARALLEL - select VIDEO_LCD_PANEL_I2C - ---help--- - Select this for eDP LCD panels with 4 lanes running at 1.62G, - connected via an ANX9804 bridge chip. - -config VIDEO_LCD_PANEL_HITACHI_TX18D42VM - bool "Hitachi tx18d42vm LCD panel" - select VIDEO_LCD_HITACHI_TX18D42VM - select VIDEO_LCD_IF_LVDS - ---help--- - 7.85" 1024x768 Hitachi tx18d42vm LCD panel support - -config VIDEO_LCD_TL059WV5C0 - bool "tl059wv5c0 LCD panel" - select VIDEO_LCD_PANEL_I2C - select VIDEO_LCD_IF_PARALLEL - ---help--- - 6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and - Aigo M60/M608/M606 tablets. - -endchoice - -config SATAPWR - string "SATA power pin" - default "" - help - Set the pins used to power the SATA. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of - port H. - -config GMAC_TX_DELAY - int "GMAC Transmit Clock Delay Chain" - default 0 - ---help--- - Set the GMAC Transmit Clock Delay Chain value. - -config SPL_STACK_R_ADDR - default 0x4fe00000 if MACH_SUN4I - default 0x4fe00000 if MACH_SUN5I - default 0x4fe00000 if MACH_SUN6I - default 0x4fe00000 if MACH_SUN7I - default 0x4fe00000 if MACH_SUN8I - default 0x2fe00000 if MACH_SUN9I - default 0x4fe00000 if MACH_SUN50I - -endif -- cgit v0.10.2