From 8907c2c50408b39e93fb42b2d74ab908480320a0 Mon Sep 17 00:00:00 2001 From: Eric Nelson Date: Tue, 20 Aug 2013 11:44:43 -0700 Subject: i.MX6: nitrogen6x: force HDMI onto IPU0/DI0 Our Linux kernel switches the HDMI connector onto IPU0/DI1, but the U-Boot display driver only supports IPU0/DI0 for the time being. Because of this, a soft re-boot will leave the HDMI output connected to the wrong display port and prevent video from being displayed. Signed-off-by: Eric Nelson diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index 79ab449..1419f36 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -666,7 +666,8 @@ static void setup_display(void) writel(reg, &iomux->gpr[2]); reg = readl(&iomux->gpr[3]); - reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK) + reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK + |IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <gpr[3]); -- cgit v0.10.2 From 661edaafd44c6a7001a95d3a93a7dc03acc18a39 Mon Sep 17 00:00:00 2001 From: Andreas Wass Date: Wed, 14 Aug 2013 23:45:03 +0200 Subject: ARM: mxs: Added application UART driver The driver makes it possible to use an application UART as the U-Boot output console for Freescale i.MX23/i.MX28 devices. Signed-off-by: Andreas Wass Cc: Fabio Estevam Cc: Marek Vasut Acked-by: Marek Vasut diff --git a/arch/arm/include/asm/arch-mxs/regs-uartapp.h b/arch/arm/include/asm/arch-mxs/regs-uartapp.h new file mode 100644 index 0000000..7ceb810 --- /dev/null +++ b/arch/arm/include/asm/arch-mxs/regs-uartapp.h @@ -0,0 +1,220 @@ +/* + * Freescale MXS UARTAPP Register Definitions + * + * Copyright (C) 2013 Andreas Wass + * + * Based on code from LTIB: + * Copyright 2008-2010 Freescale Semiconductor, Inc. All Rights Reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __ARCH_ARM___MXS_UARTAPP_H +#define __ARCH_ARM___MXS_UARTAPP_H + +#include + +#ifndef __ASSEMBLY__ +struct mxs_uartapp_regs { + mxs_reg_32(hw_uartapp_ctrl0) + mxs_reg_32(hw_uartapp_ctrl1) + mxs_reg_32(hw_uartapp_ctrl2) + mxs_reg_32(hw_uartapp_linectrl) + mxs_reg_32(hw_uartapp_linectrl2) + mxs_reg_32(hw_uartapp_intr) + mxs_reg_32(hw_uartapp_data) + mxs_reg_32(hw_uartapp_stat) + mxs_reg_32(hw_uartapp_debug) + mxs_reg_32(hw_uartapp_version) + mxs_reg_32(hw_uartapp_autobaud) +}; +#endif + +#define UARTAPP_CTRL0_SFTRST_MASK (1 << 31) +#define UARTAPP_CTRL0_CLKGATE_MASK (1 << 30) +#define UARTAPP_CTRL0_RUN_MASK (1 << 29) +#define UARTAPP_CTRL0_RX_SOURCE_MASK (1 << 28) +#define UARTAPP_CTRL0_RXTO_ENABLE_MASK (1 << 27) +#define UARTAPP_CTRL0_RXTIMEOUT_OFFSET 16 +#define UARTAPP_CTRL0_RXTIMEOUT_MASK (0x7FF << 16) +#define UARTAPP_CTRL0_XFER_COUNT_OFFSET 0 +#define UARTAPP_CTRL0_XFER_COUNT_MASK 0xFFFF + +#define UARTAPP_CTRL1_RUN_MASK (1 << 28) + +#define UARTAPP_CTRL1_XFER_COUNT_OFFSET 0 +#define UARTAPP_CTRL1_XFER_COUNT_MASK 0xFFFF + +#define UARTAPP_CTRL2_INVERT_RTS_MASK (1 << 31) +#define UARTAPP_CTRL2_INVERT_CTS_MASK (1 << 30) +#define UARTAPP_CTRL2_INVERT_TX_MASK (1 << 29) +#define UARTAPP_CTRL2_INVERT_RX_MASK (1 << 28) +#define UARTAPP_CTRL2_RTS_SEMAPHORE_MASK (1 << 27) +#define UARTAPP_CTRL2_DMAONERR_MASK (1 << 26) +#define UARTAPP_CTRL2_TXDMAE_MASK (1 << 25) +#define UARTAPP_CTRL2_RXDMAE_MASK (1 << 24) +#define UARTAPP_CTRL2_RXIFLSEL_OFFSET 20 +#define UARTAPP_CTRL2_RXIFLSEL_MASK (0x7 << 20) + +#define UARTAPP_CTRL2_RXIFLSEL_NOT_EMPTY (0x0 << 20) +#define UARTAPP_CTRL2_RXIFLSEL_ONE_QUARTER (0x1 << 20) +#define UARTAPP_CTRL2_RXIFLSEL_ONE_HALF (0x2 << 20) +#define UARTAPP_CTRL2_RXIFLSEL_THREE_QUARTERS (0x3 << 20) +#define UARTAPP_CTRL2_RXIFLSEL_SEVEN_EIGHTHS (0x4 << 20) +#define UARTAPP_CTRL2_RXIFLSEL_INVALID5 (0x5 << 20) +#define UARTAPP_CTRL2_RXIFLSEL_INVALID6 (0x6 << 20) +#define UARTAPP_CTRL2_RXIFLSEL_INVALID7 (0x7 << 20) +#define UARTAPP_CTRL2_TXIFLSEL_OFFSET 16 +#define UARTAPP_CTRL2_TXIFLSEL_MASK (0x7 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_EMPTY (0x0 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_ONE_QUARTER (0x1 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_ONE_HALF (0x2 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_THREE_QUARTERS (0x3 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_SEVEN_EIGHTHS (0x4 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_INVALID5 (0x5 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_INVALID6 (0x6 << 16) +#define UARTAPP_CTRL2_TXIFLSEL_INVALID7 (0x7 << 16) +#define UARTAPP_CTRL2_CTSEN_MASK (1 << 15) +#define UARTAPP_CTRL2_RTSEN_MASK (1 << 14) +#define UARTAPP_CTRL2_OUT2_MASK (1 << 13) +#define UARTAPP_CTRL2_OUT1_MASK (1 << 12) +#define UARTAPP_CTRL2_RTS_MASK (1 << 11) +#define UARTAPP_CTRL2_DTR_MASK (1 << 10) +#define UARTAPP_CTRL2_RXE_MASK (1 << 9) +#define UARTAPP_CTRL2_TXE_MASK (1 << 8) +#define UARTAPP_CTRL2_LBE_MASK (1 << 7) +#define UARTAPP_CTRL2_USE_LCR2_MASK (1 << 6) + +#define UARTAPP_CTRL2_SIRLP_MASK (1 << 2) +#define UARTAPP_CTRL2_SIREN_MASK (1 << 1) +#define UARTAPP_CTRL2_UARTEN_MASK 0x01 + +#define UARTAPP_LINECTRL_BAUD_DIVINT_OFFSET 16 +#define UARTAPP_LINECTRL_BAUD_DIVINT_MASK (0xFFFF << 16) +#define UARTAPP_LINECTRL_EXTRACT_BAUD_DIVINT_OFFSET 6 + +#define UARTAPP_LINECTRL_BAUD_DIVFRAC_OFFSET 8 +#define UARTAPP_LINECTRL_BAUD_DIVFRAC_MASK (0x3F << 8) +#define UARTAPP_LINECTRL_EXTRACT_BAUD_DIVFRAC_MASK 0x3F + +#define UARTAPP_LINECTRL_SPS_MASK (1 << 7) +#define UARTAPP_LINECTRL_WLEN_OFFSET 5 +#define UARTAPP_LINECTRL_WLEN_MASK (0x03 << 5) +#define UARTAPP_LINECTRL_WLEN_5BITS (0x00 << 5) +#define UARTAPP_LINECTRL_WLEN_6BITS (0x01 << 5) +#define UARTAPP_LINECTRL_WLEN_7BITS (0x02 << 5) +#define UARTAPP_LINECTRL_WLEN_8BITS (0x03 << 5) + +#define UARTAPP_LINECTRL_FEN_MASK (1 << 4) +#define UARTAPP_LINECTRL_STP2_MASK (1 << 3) +#define UARTAPP_LINECTRL_EPS_MASK (1 << 2) +#define UARTAPP_LINECTRL_PEN_MASK (1 << 1) +#define UARTAPP_LINECTRL_BRK_MASK 1 + +#define UARTAPP_LINECTRL2_BAUD_DIVINT_OFFSET 16 +#define UARTAPP_LINECTRL2_BAUD_DIVINT_MASK (0xFFFF << 16) +#define UARTAPP_LINECTRL2_EXTRACT_BAUD_DIVINT_OFFSET 6 + +#define UARTAPP_LINECTRL2_BAUD_DIVFRAC_OFFSET 8 +#define UARTAPP_LINECTRL2_BAUD_DIVFRAC_MASK (0x3F << 8) +#define UARTAPP_LINECTRL2_EXTRACT_BAUD_DIVFRAC_MASK 0x3F + +#define UARTAPP_LINECTRL2_SPS_MASK (1 << 7) +#define UARTAPP_LINECTRL2_WLEN_OFFSET 5 +#define UARTAPP_LINECTRL2_WLEN_MASK (0x03 << 5) +#define UARTAPP_LINECTRL2_WLEN_5BITS (0x00 << 5) +#define UARTAPP_LINECTRL2_WLEN_6BITS (0x01 << 5) +#define UARTAPP_LINECTRL2_WLEN_7BITS (0x02 << 5) +#define UARTAPP_LINECTRL2_WLEN_8BITS (0x03 << 5) + +#define UARTAPP_LINECTRL2_FEN_MASK (1 << 4) +#define UARTAPP_LINECTRL2_STP2_MASK (1 << 3) +#define UARTAPP_LINECTRL2_EPS_MASK (1 << 2) +#define UARTAPP_LINECTRL2_PEN_MASK (1 << 1) + +#define UARTAPP_INTR_ABDIEN_MASK (1 << 27) +#define UARTAPP_INTR_OEIEN_MASK (1 << 26) +#define UARTAPP_INTR_BEIEN_MASK (1 << 25) +#define UARTAPP_INTR_PEIEN_MASK (1 << 24) +#define UARTAPP_INTR_FEIEN_MASK (1 << 23) +#define UARTAPP_INTR_RTIEN_MASK (1 << 22) +#define UARTAPP_INTR_TXIEN_MASK (1 << 21) +#define UARTAPP_INTR_RXIEN_MASK (1 << 20) +#define UARTAPP_INTR_DSRMIEN_MASK (1 << 19) +#define UARTAPP_INTR_DCDMIEN_MASK (1 << 18) +#define UARTAPP_INTR_CTSMIEN_MASK (1 << 17) +#define UARTAPP_INTR_RIMIEN_MASK (1 << 16) + +#define UARTAPP_INTR_ABDIS_MASK (1 << 11) +#define UARTAPP_INTR_OEIS_MASK (1 << 10) +#define UARTAPP_INTR_BEIS_MASK (1 << 9) +#define UARTAPP_INTR_PEIS_MASK (1 << 8) +#define UARTAPP_INTR_FEIS_MASK (1 << 7) +#define UARTAPP_INTR_RTIS_MASK (1 << 6) +#define UARTAPP_INTR_TXIS_MASK (1 << 5) +#define UARTAPP_INTR_RXIS_MASK (1 << 4) +#define UARTAPP_INTR_DSRMIS_MASK (1 << 3) +#define UARTAPP_INTR_DCDMIS_MASK (1 << 2) +#define UARTAPP_INTR_CTSMIS_MASK (1 << 1) +#define UARTAPP_INTR_RIMIS_MASK 0x1 + +#define UARTAPP_DATA_DATA_OFFSET 0 +#define UARTAPP_DATA_DATA_MASK 0xFFFFFFFF +#define UARTAPP_STAT_PRESENT_MASK (1 << 31) +#define UARTAPP_STAT_PRESENT_UNAVAILABLE (0x0 << 31) +#define UARTAPP_STAT_PRESENT_AVAILABLE (0x1 << 31) + +#define UARTAPP_STAT_HISPEED_MASK (1 << 30) +#define UARTAPP_STAT_HISPEED_UNAVAILABLE (0x0 << 30) +#define UARTAPP_STAT_HISPEED_AVAILABLE (0x1 << 30) + +#define UARTAPP_STAT_BUSY_MASK (1 << 29) +#define UARTAPP_STAT_CTS_MASK (1 << 28) +#define UARTAPP_STAT_TXFE_MASK (1 << 27) +#define UARTAPP_STAT_RXFF_MASK (1 << 26) +#define UARTAPP_STAT_TXFF_MASK (1 << 25) +#define UARTAPP_STAT_RXFE_MASK (1 << 24) +#define UARTAPP_STAT_RXBYTE_INVALID_OFFSET 20 +#define UARTAPP_STAT_RXBYTE_INVALID_MASK (0xF << 20) + +#define UARTAPP_STAT_OERR_MASK (1 << 19) +#define UARTAPP_STAT_BERR_MASK (1 << 18) +#define UARTAPP_STAT_PERR_MASK (1 << 17) +#define UARTAPP_STAT_FERR_MASK (1 << 16) +#define UARTAPP_STAT_RXCOUNT_OFFSET 0 +#define UARTAPP_STAT_RXCOUNT_MASK 0xFFFF + +#define UARTAPP_DEBUG_RXIBAUD_DIV_OFFSET 16 +#define UARTAPP_DEBUG_RXIBAUD_DIV_MASK (0xFFFF << 16) + +#define UARTAPP_DEBUG_RXFBAUD_DIV_OFFSET 10 +#define UARTAPP_DEBUG_RXFBAUD_DIV_MASK (0x3F << 10) + +#define UARTAPP_DEBUG_TXDMARUN_MASK (1 << 5) +#define UARTAPP_DEBUG_RXDMARUN_MASK (1 << 4) +#define UARTAPP_DEBUG_TXCMDEND_MASK (1 << 3) +#define UARTAPP_DEBUG_RXCMDEND_MASK (1 << 2) +#define UARTAPP_DEBUG_TXDMARQ_MASK (1 << 1) +#define UARTAPP_DEBUG_RXDMARQ_MASK 0x01 + +#define UARTAPP_VERSION_MAJOR_OFFSET 24 +#define UARTAPP_VERSION_MAJOR_MASK (0xFF << 24) + +#define UARTAPP_VERSION_MINOR_OFFSET 16 +#define UARTAPP_VERSION_MINOR_MASK (0xFF << 16) + +#define UARTAPP_VERSION_STEP_OFFSET 0 +#define UARTAPP_VERSION_STEP_MASK 0xFFFF + +#define UARTAPP_AUTOBAUD_REFCHAR1_OFFSET 24 +#define UARTAPP_AUTOBAUD_REFCHAR1_MASK (0xFF << 24) + +#define UARTAPP_AUTOBAUD_REFCHAR0_OFFSET 16 +#define UARTAPP_AUTOBAUD_REFCHAR0_MASK (0xFF << 16) + +#define UARTAPP_AUTOBAUD_UPDATE_TX_MASK (1 << 4) +#define UARTAPP_AUTOBAUD_TWO_REF_CHARS_MASK (1 << 3) +#define UARTAPP_AUTOBAUD_START_WITH_RUNBIT_MASK (1 << 2) +#define UARTAPP_AUTOBAUD_START_BAUD_DETECT_MASK (1 << 1) +#define UARTAPP_AUTOBAUD_BAUD_DETECT_ENABLE_MASK 0x01 +#endif /* __ARCH_ARM___UARTAPP_H */ diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 697f2bb..4c45bfa 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -38,6 +38,7 @@ COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o COBJS-$(CONFIG_ZYNQ_SERIAL) += serial_zynq.o COBJS-$(CONFIG_BFIN_SERIAL) += serial_bfin.o COBJS-$(CONFIG_FSL_LPUART) += serial_lpuart.o +COBJS-$(CONFIG_MXS_AUART) += mxs_auart.o ifndef CONFIG_SPL_BUILD COBJS-$(CONFIG_USB_TTY) += usbtty.o diff --git a/drivers/serial/mxs_auart.c b/drivers/serial/mxs_auart.c new file mode 100644 index 0000000..7cfe5bc --- /dev/null +++ b/drivers/serial/mxs_auart.c @@ -0,0 +1,151 @@ +/* + * Freescale i.MX23/i.MX28 AUART driver + * + * Copyright (C) 2013 Andreas Wass + * + * Based on the MXC serial driver: + * + * (c) 2007 Sascha Hauer + * + * Further based on the Linux mxs-auart.c driver: + * + * Freescale STMP37XX/STMP38X Application UART drkiver + * Copyright 2008-2010 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#ifndef CONFIG_MXS_AUART_BASE +#error "CONFIG_MXS_AUART_BASE must be set to the base UART to use" +#endif + +/* AUART clock always supplied by XTAL and always 24MHz */ +#define MXS_AUART_CLK 24000000 + +static struct mxs_uartapp_regs *get_uartapp_registers(void) +{ + return (struct mxs_uartapp_regs *)CONFIG_MXS_AUART_BASE; +} + +/** + * Sets the baud rate and settings. + * The settings are: 8 data bits, no parit and 1 stop bit. + */ +void mxs_auart_setbrg(void) +{ + u32 div; + u32 linectrl = 0; + struct mxs_uartapp_regs *regs = get_uartapp_registers(); + + if (!gd->baudrate) + gd->baudrate = CONFIG_BAUDRATE; + + /* + * From i.MX28 datasheet: + * div is calculated by calculating UARTCLK*32/baudrate, rounded to int + * div must be between 0xEC and 0x003FFFC0 inclusive + * Lowest 6 bits of div goes in BAUD_DIVFRAC part of LINECTRL register + * Next 16 bits goes in BAUD_DIVINT part of LINECTRL register + */ + div = (MXS_AUART_CLK * 32) / gd->baudrate; + if (div < 0xEC || div > 0x003FFFC0) + return; + + linectrl |= ((div & UARTAPP_LINECTRL_EXTRACT_BAUD_DIVFRAC_MASK) << + UARTAPP_LINECTRL_BAUD_DIVFRAC_OFFSET) & + UARTAPP_LINECTRL_BAUD_DIVFRAC_MASK; + linectrl |= ((div >> UARTAPP_LINECTRL_EXTRACT_BAUD_DIVINT_OFFSET) << + UARTAPP_LINECTRL_BAUD_DIVINT_OFFSET) & + UARTAPP_LINECTRL_BAUD_DIVINT_MASK; + + /* Word length: 8 bits */ + linectrl |= UARTAPP_LINECTRL_WLEN_8BITS; + + /* Enable FIFOs. */ + linectrl |= UARTAPP_LINECTRL_FEN_MASK; + + /* Write above settings, no parity, 1 stop bit */ + writel(linectrl, ®s->hw_uartapp_linectrl); +} + +int mxs_auart_init(void) +{ + struct mxs_uartapp_regs *regs = get_uartapp_registers(); + /* Reset everything */ + mxs_reset_block(®s->hw_uartapp_ctrl0_reg); + /* Disable interrupts */ + writel(0, ®s->hw_uartapp_intr); + /* Set baud rate and settings */ + serial_setbrg(); + /* Disable RTS and CTS, ignore LINECTRL2 register */ + writel(UARTAPP_CTRL2_RTSEN_MASK | + UARTAPP_CTRL2_CTSEN_MASK | + UARTAPP_CTRL2_USE_LCR2_MASK, + ®s->hw_uartapp_ctrl2_clr); + /* Enable receiver, transmitter and UART */ + writel(UARTAPP_CTRL2_RXE_MASK | + UARTAPP_CTRL2_TXE_MASK | + UARTAPP_CTRL2_UARTEN_MASK, + ®s->hw_uartapp_ctrl2_set); + return 0; +} + +void mxs_auart_putc(const char c) +{ + struct mxs_uartapp_regs *regs = get_uartapp_registers(); + /* Wait in loop while the transmit FIFO is full */ + while (readl(®s->hw_uartapp_stat) & UARTAPP_STAT_TXFF_MASK) + ; + + writel(c, ®s->hw_uartapp_data); + + if (c == '\n') + mxs_auart_putc('\r'); +} + +int mxs_auart_tstc(void) +{ + struct mxs_uartapp_regs *regs = get_uartapp_registers(); + /* Checks if receive FIFO is empty */ + return !(readl(®s->hw_uartapp_stat) & UARTAPP_STAT_RXFE_MASK); +} + +int mxs_auart_getc(void) +{ + struct mxs_uartapp_regs *regs = get_uartapp_registers(); + /* Wait until a character is available to read */ + while (!mxs_auart_tstc()) + ; + /* Read the character from the data register */ + return readl(®s->hw_uartapp_data) & 0xFF; +} + +static struct serial_device mxs_auart_drv = { + .name = "mxs_auart_serial", + .start = mxs_auart_init, + .stop = NULL, + .setbrg = mxs_auart_setbrg, + .putc = mxs_auart_putc, + .puts = default_serial_puts, + .getc = mxs_auart_getc, + .tstc = mxs_auart_tstc, +}; + +void mxs_auart_initialize(void) +{ + serial_register(&mxs_auart_drv); +} + +__weak struct serial_device *default_serial_console(void) +{ + return &mxs_auart_drv; +} diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c index 6730135..336ff35 100644 --- a/drivers/serial/serial.c +++ b/drivers/serial/serial.c @@ -159,6 +159,7 @@ serial_initfunc(pl01x_serial_initialize); serial_initfunc(s3c44b0_serial_initialize); serial_initfunc(sa1100_serial_initialize); serial_initfunc(sh_serial_initialize); +serial_initfunc(mxs_auart_initialize); /** * serial_register() - Register serial driver with serial driver core @@ -251,6 +252,7 @@ void serial_initialize(void) s3c44b0_serial_initialize(); sa1100_serial_initialize(); sh_serial_initialize(); + mxs_auart_initialize(); serial_assign(default_serial_console()->name); } -- cgit v0.10.2 From 0cfb8afed3939e2db4e028a86ea4803f7475941f Mon Sep 17 00:00:00 2001 From: Andreas Wass Date: Fri, 16 Aug 2013 18:24:37 +0200 Subject: ARM: mxs: Add mx28evk_auart_console target The target uses AUART 3 instead of the DUART for console output. Signed-off-by: Andreas Wass Cc: Fabio Estevam Cc: Marek Vasut diff --git a/boards.cfg b/boards.cfg index 454da7f..79d6cd8 100644 --- a/boards.cfg +++ b/boards.cfg @@ -203,6 +203,7 @@ mx23evk arm arm926ejs mx23evk freesca m28evk arm arm926ejs m28evk denx mxs m28evk mx28evk arm arm926ejs mx28evk freescale mxs mx28evk:ENV_IS_IN_MMC mx28evk_nand arm arm926ejs mx28evk freescale mxs mx28evk:ENV_IS_IN_NAND +mx28evk_auart_console arm arm926ejs mx28evk freescale mxs mx28evk:MXS_AUART,MXS_AUART_BASE=MXS_UARTAPP3_BASE,ENV_IS_IN_MMC sc_sps_1 arm arm926ejs sc_sps_1 schulercontrol mxs nhk8815 arm arm926ejs nhk8815 st nomadik nhk8815_onenand arm arm926ejs nhk8815 st nomadik nhk8815:BOOT_ONENAND diff --git a/include/configs/mxs.h b/include/configs/mxs.h index a684166..124dc1e 100644 --- a/include/configs/mxs.h +++ b/include/configs/mxs.h @@ -119,11 +119,16 @@ /* GPIO */ #define CONFIG_MXS_GPIO -/* DUART Serial Driver */ +/* + * DUART Serial Driver. + * Conflicts with AUART driver which can be set by board. + */ +#ifndef CONFIG_MXS_AUART #define CONFIG_PL011_SERIAL #define CONFIG_PL011_CLOCK 24000000 #define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } #define CONFIG_CONS_INDEX 0 +#endif /* Default baudrate can be overriden by board! */ #ifndef CONFIG_BAUDRATE #define CONFIG_BAUDRATE 115200 -- cgit v0.10.2 From ddb636bd66f527e6680faed5a6adced69836517d Mon Sep 17 00:00:00 2001 From: Eric Nelson Date: Fri, 2 Aug 2013 10:37:00 -0700 Subject: fec_mxc: set ethaddr if fuses burned and not previously set Without this change, the following message is generated: Warning: FEC using MAC address from net device See doc/README.enetaddr for details. Signed-off-by: Eric Nelson diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c index e14a359..690e572 100644 --- a/drivers/net/fec_mxc.c +++ b/drivers/net/fec_mxc.c @@ -980,6 +980,8 @@ static int fec_probe(bd_t *bd, int dev_id, uint32_t base_addr, if (fec_get_hwaddr(edev, dev_id, ethaddr) == 0) { debug("got MAC%d address from fuse: %pM\n", dev_id, ethaddr); memcpy(edev->enetaddr, ethaddr, 6); + if (!getenv("ethaddr")) + eth_setenv_enetaddr("ethaddr", ethaddr); } return ret; err3: -- cgit v0.10.2 From 49b0415a80474eeb7876dede868c65764d6e973a Mon Sep 17 00:00:00 2001 From: Amaury Pouly Date: Thu, 1 Aug 2013 16:21:00 +0200 Subject: mmc: mxsmmc: Enable MMC HC support Enable support for high-capacity eMMC and MMC cards. The MXS MMC driver has no problem with those. Signed-off-by: Marek Vasut Signed-off-by: Amaury Pouly Cc: Andy Fleming Cc: Fabio Estevam Cc: Stefano Babic Cc: Otavio Salvador Reviewed-by: Otavio Salvador diff --git a/drivers/mmc/mxsmmc.c b/drivers/mmc/mxsmmc.c index e5a5d75..245f9d0 100644 --- a/drivers/mmc/mxsmmc.c +++ b/drivers/mmc/mxsmmc.c @@ -410,7 +410,8 @@ int mxsmmc_initialize(bd_t *bis, int id, int (*wp)(int), int (*cd)(int)) mmc->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; mmc->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT | - MMC_MODE_HS_52MHz | MMC_MODE_HS; + MMC_MODE_HS_52MHz | MMC_MODE_HS | + MMC_MODE_HC; /* * SSPCLK = 480 * 18 / 29 / 1 = 297.731 MHz -- cgit v0.10.2 From 4655d40f34c8141651d10c9e0b17511728618bda Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 26 Jun 2013 17:26:27 +0200 Subject: tools: imx_header should not include flash_offset MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Doing a make distclean; make mx6qsabresd_config; make and hexdump -C u-boot.imx | less ... 00000360 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000003f0 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 |................| ^^^^^^^^^^^ 00000400 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00001000 13 00 00 ea 14 f0 9f e5 14 f0 9f e5 14 f0 9f e5 |...ê.ð.å.ð.å.ð.å| ... shows the flash_offset value being written into the final generated image, wich is not correct. Instead create flash_offset as static variable such that the generated image is "clean". 00000360 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00001000 13 00 00 ea 14 f0 9f e5 14 f0 9f e5 14 f0 9f e5 |...ê.ð.å.ð.å.ð.å| Signed-off-by: Stefano Babic diff --git a/tools/imximage.c b/tools/imximage.c index c8a9ad5..a347b9b 100644 --- a/tools/imximage.c +++ b/tools/imximage.c @@ -52,6 +52,7 @@ static table_entry_t imximage_versions[] = { static struct imx_header imximage_header; static uint32_t imximage_version; +static uint32_t imximage_flash_offset; static set_dcd_val_t set_dcd_val; static set_dcd_rst_t set_dcd_rst; @@ -327,9 +328,9 @@ static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, set_hdr_func(imxhdr); break; case CMD_BOOT_FROM: - imxhdr->flash_offset = get_table_entry_id(imximage_bootops, + imximage_flash_offset = get_table_entry_id(imximage_bootops, "imximage boot option", token); - if (imxhdr->flash_offset == -1) { + if (imximage_flash_offset == -1) { fprintf(stderr, "Error: %s[%d] -Invalid boot device" "(%s)\n", name, lineno, token); exit(EXIT_FAILURE); @@ -338,7 +339,7 @@ static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, cmd_ver_first = 0; break; case CMD_BOOT_OFFSET: - imxhdr->flash_offset = get_cfg_value(token, name, lineno); + imximage_flash_offset = get_cfg_value(token, name, lineno); if (unlikely(cmd_ver_first != 1)) cmd_ver_first = 0; break; @@ -439,7 +440,7 @@ static uint32_t parse_cfg_file(struct imx_header *imxhdr, char *name) fclose(fd); /* Exit if there is no BOOT_FROM field specifying the flash_offset */ - if (imxhdr->flash_offset == FLASH_OFFSET_UNDEFINED) { + if (imximage_flash_offset == FLASH_OFFSET_UNDEFINED) { fprintf(stderr, "Error: No BOOT_FROM tag in %s\n", name); exit(EXIT_FAILURE); } @@ -497,14 +498,14 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, */ imximage_version = IMXIMAGE_V1; /* Be able to detect if the cfg file has no BOOT_FROM tag */ - imxhdr->flash_offset = FLASH_OFFSET_UNDEFINED; + imximage_flash_offset = FLASH_OFFSET_UNDEFINED; set_hdr_func(imxhdr); /* Parse dcd configuration file */ dcd_len = parse_cfg_file(imxhdr, params->imagename); /* Set the imx header */ - (*set_imx_hdr)(imxhdr, dcd_len, params->ep, imxhdr->flash_offset); + (*set_imx_hdr)(imxhdr, dcd_len, params->ep, imximage_flash_offset); /* * ROM bug alert @@ -515,7 +516,7 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, * * The remaining fraction of a block bytes would not be loaded! */ - *header_size_ptr = ROUND(sbuf->st_size + imxhdr->flash_offset, 4096); + *header_size_ptr = ROUND(sbuf->st_size + imximage_flash_offset, 4096); } int imximage_check_params(struct mkimage_params *params) diff --git a/tools/imximage.h b/tools/imximage.h index 214187b..ec629a5 100644 --- a/tools/imximage.h +++ b/tools/imximage.h @@ -147,7 +147,6 @@ struct imx_header { imx_header_v1_t hdr_v1; imx_header_v2_t hdr_v2; } header; - uint32_t flash_offset; } __attribute__((aligned(4096))); typedef void (*set_dcd_val_t)(struct imx_header *imxhdr, -- cgit v0.10.2 From 3150f92c29677244977ddfb6cbbf7e25f3581a79 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 26 Jun 2013 18:08:37 +0200 Subject: tools: rename mximage_flash_offset to imximage_ivt_offset This better reflects the naming from the Reference Manual as well as fits better since "flash" is not really applicabe for SATA. Signed-off-by: Stefano Babic diff --git a/tools/imximage.c b/tools/imximage.c index a347b9b..494446e 100644 --- a/tools/imximage.c +++ b/tools/imximage.c @@ -52,7 +52,8 @@ static table_entry_t imximage_versions[] = { static struct imx_header imximage_header; static uint32_t imximage_version; -static uint32_t imximage_flash_offset; +/* Image Vector Table Offset */ +static uint32_t imximage_ivt_offset; static set_dcd_val_t set_dcd_val; static set_dcd_rst_t set_dcd_rst; @@ -328,9 +329,9 @@ static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, set_hdr_func(imxhdr); break; case CMD_BOOT_FROM: - imximage_flash_offset = get_table_entry_id(imximage_bootops, + imximage_ivt_offset = get_table_entry_id(imximage_bootops, "imximage boot option", token); - if (imximage_flash_offset == -1) { + if (imximage_ivt_offset == -1) { fprintf(stderr, "Error: %s[%d] -Invalid boot device" "(%s)\n", name, lineno, token); exit(EXIT_FAILURE); @@ -339,7 +340,7 @@ static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, cmd_ver_first = 0; break; case CMD_BOOT_OFFSET: - imximage_flash_offset = get_cfg_value(token, name, lineno); + imximage_ivt_offset = get_cfg_value(token, name, lineno); if (unlikely(cmd_ver_first != 1)) cmd_ver_first = 0; break; @@ -440,7 +441,7 @@ static uint32_t parse_cfg_file(struct imx_header *imxhdr, char *name) fclose(fd); /* Exit if there is no BOOT_FROM field specifying the flash_offset */ - if (imximage_flash_offset == FLASH_OFFSET_UNDEFINED) { + if (imximage_ivt_offset == FLASH_OFFSET_UNDEFINED) { fprintf(stderr, "Error: No BOOT_FROM tag in %s\n", name); exit(EXIT_FAILURE); } @@ -498,14 +499,14 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, */ imximage_version = IMXIMAGE_V1; /* Be able to detect if the cfg file has no BOOT_FROM tag */ - imximage_flash_offset = FLASH_OFFSET_UNDEFINED; + imximage_ivt_offset = FLASH_OFFSET_UNDEFINED; set_hdr_func(imxhdr); /* Parse dcd configuration file */ dcd_len = parse_cfg_file(imxhdr, params->imagename); /* Set the imx header */ - (*set_imx_hdr)(imxhdr, dcd_len, params->ep, imximage_flash_offset); + (*set_imx_hdr)(imxhdr, dcd_len, params->ep, imximage_ivt_offset); /* * ROM bug alert @@ -516,7 +517,7 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, * * The remaining fraction of a block bytes would not be loaded! */ - *header_size_ptr = ROUND(sbuf->st_size + imximage_flash_offset, 4096); + *header_size_ptr = ROUND(sbuf->st_size + imximage_ivt_offset, 4096); } int imximage_check_params(struct mkimage_params *params) -- cgit v0.10.2 From 377e367a8558c5327c925387ecf1f0a4ee7ca177 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 26 Jun 2013 23:50:06 +0200 Subject: tools: dynamically allocate imx_header in imximage Change to dynamically allocate the imx_header to correctly allocate the IVT, Boot Data and DCD at correct locations depending on the boot media. Also check that the Image Vector Table Offset + IVT + Boot Data + DCD <= Initial Load Region Size. Previously struct imx_header was always 4096 bytes and was not dealing correctly with the Image Vector Table Offset. Now, the memory allocation looks for e.g. SD boot like this Storage u-boot.imx RAM Device 00000000 177ff000 <-------------- | 00000400 00000000 d1 00 20 40 IVT.header 177ff400 <------- | 00000404 00000004 00 00 80 17 IVT.entry 177ff404 ----------- | 00000408 00000008 00 00 00 00 IVT.reserved1 177ff408 | | | 0000040C 0000000C 2c f4 7f 17 IVT.dcd 177ff40C ------ | | | 00000410 00000010 20 f4 7f 17 IVT.boot 177ff410 ---- | | | | 00000414 00000014 00 f4 7f 17 IVT.self 177ff414 -------- | | 00000418 00000018 00 00 00 00 IVT.csf 177ff418 | | | | 0000041C 0000001C 00 00 00 00 IVT.reserved2 177ff41C | | | | 00000420 00000020 00 f0 7f 17 BootData.start 177ff420 <--- | | --- 00000424 00000024 00 60 03 00 BootData.length 177ff424 | | 00000428 00000028 00 00 00 00 BootData.plugin 177ff428 | | 0000042C 0000002C d2 03 30 40 DCD.header 177ff42C <----- | ... | 00001000 00000c00 13 00 00 ea U-Boot Start 17800000 <---------- While at it also remove the unused #define HEADER_OFFSET. Signed-off-by: Stefano Babic diff --git a/tools/imximage.c b/tools/imximage.c index 494446e..2b4909e 100644 --- a/tools/imximage.c +++ b/tools/imximage.c @@ -31,7 +31,7 @@ static table_entry_t imximage_cmds[] = { * Supported Boot options for configuration file * this is needed to set the correct flash offset */ -static table_entry_t imximage_bootops[] = { +static table_entry_t imximage_boot_offset[] = { {FLASH_OFFSET_ONENAND, "onenand", "OneNAND Flash",}, {FLASH_OFFSET_NAND, "nand", "NAND Flash", }, {FLASH_OFFSET_NOR, "nor", "NOR Flash", }, @@ -42,6 +42,20 @@ static table_entry_t imximage_bootops[] = { }; /* + * Supported Boot options for configuration file + * this is needed to determine the initial load size + */ +static table_entry_t imximage_boot_loadsize[] = { + {FLASH_LOADSIZE_ONENAND, "onenand", "OneNAND Flash",}, + {FLASH_LOADSIZE_NAND, "nand", "NAND Flash", }, + {FLASH_LOADSIZE_NOR, "nor", "NOR Flash", }, + {FLASH_LOADSIZE_SATA, "sata", "SATA Disk", }, + {FLASH_LOADSIZE_SD, "sd", "SD Card", }, + {FLASH_LOADSIZE_SPI, "spi", "SPI Flash", }, + {-1, "", "Invalid", }, +}; + +/* * IMXIMAGE version definition for i.MX chips */ static table_entry_t imximage_versions[] = { @@ -54,6 +68,8 @@ static struct imx_header imximage_header; static uint32_t imximage_version; /* Image Vector Table Offset */ static uint32_t imximage_ivt_offset; +/* Initial Load Region Size */ +static uint32_t imximage_init_loadsize; static set_dcd_val_t set_dcd_val; static set_dcd_rst_t set_dcd_rst; @@ -195,7 +211,8 @@ static void set_imx_hdr_v1(struct imx_header *imxhdr, uint32_t dcd_len, /* Set magic number */ fhdr_v1->app_code_barker = APP_CODE_BARKER; - hdr_base = entry_point - sizeof(struct imx_header); + /* TODO: check i.MX image V1 handling, for now use 'old' style */ + hdr_base = entry_point - 4096; fhdr_v1->app_dest_ptr = hdr_base - flash_offset; fhdr_v1->app_code_jump_vector = entry_point; @@ -222,12 +239,13 @@ static void set_imx_hdr_v2(struct imx_header *imxhdr, uint32_t dcd_len, fhdr_v2->entry = entry_point; fhdr_v2->reserved1 = fhdr_v2->reserved2 = 0; - fhdr_v2->self = hdr_base = entry_point - sizeof(struct imx_header); - + hdr_base = entry_point - imximage_init_loadsize + + flash_offset; + fhdr_v2->self = hdr_base; fhdr_v2->dcd_ptr = hdr_base + offsetof(imx_header_v2_t, dcd_table); fhdr_v2->boot_data_ptr = hdr_base + offsetof(imx_header_v2_t, boot_data); - hdr_v2->boot_data.start = hdr_base - flash_offset; + hdr_v2->boot_data.start = entry_point - imximage_init_loadsize; /* Security feature are not supported */ fhdr_v2->csf = 0; @@ -329,13 +347,24 @@ static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, set_hdr_func(imxhdr); break; case CMD_BOOT_FROM: - imximage_ivt_offset = get_table_entry_id(imximage_bootops, + imximage_ivt_offset = get_table_entry_id(imximage_boot_offset, "imximage boot option", token); if (imximage_ivt_offset == -1) { fprintf(stderr, "Error: %s[%d] -Invalid boot device" "(%s)\n", name, lineno, token); exit(EXIT_FAILURE); } + + imximage_init_loadsize = + get_table_entry_id(imximage_boot_loadsize, + "imximage boot option", token); + + if (imximage_init_loadsize == -1) { + fprintf(stderr, + "Error: %s[%d] -Invalid boot device(%s)\n", + name, lineno, token); + exit(EXIT_FAILURE); + } if (unlikely(cmd_ver_first != 1)) cmd_ver_first = 0; break; @@ -517,7 +546,7 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, * * The remaining fraction of a block bytes would not be loaded! */ - *header_size_ptr = ROUND(sbuf->st_size + imximage_ivt_offset, 4096); + *header_size_ptr = ROUND(sbuf->st_size, 4096); } int imximage_check_params(struct mkimage_params *params) diff --git a/tools/imximage.h b/tools/imximage.h index ec629a5..bb04a43 100644 --- a/tools/imximage.h +++ b/tools/imximage.h @@ -13,14 +13,14 @@ #define APP_CODE_BARKER 0xB1 #define DCD_BARKER 0xB17219E9 -#define HEADER_OFFSET 0x400 - /* * NOTE: This file must be kept in sync with arch/arm/include/asm/\ * imx-common/imximage.cfg because tools/imximage.c can not * cross-include headers from arch/arm/ and vice-versa. */ #define CMD_DATA_STR "DATA" + +/* Initial Vector Table Offset */ #define FLASH_OFFSET_UNDEFINED 0xFFFFFFFF #define FLASH_OFFSET_STANDARD 0x400 #define FLASH_OFFSET_NAND FLASH_OFFSET_STANDARD @@ -30,6 +30,16 @@ #define FLASH_OFFSET_NOR 0x1000 #define FLASH_OFFSET_SATA FLASH_OFFSET_STANDARD +/* Initial Load Region Size */ +#define FLASH_LOADSIZE_UNDEFINED 0xFFFFFFFF +#define FLASH_LOADSIZE_STANDARD 0x1000 +#define FLASH_LOADSIZE_NAND FLASH_LOADSIZE_STANDARD +#define FLASH_LOADSIZE_SD FLASH_LOADSIZE_STANDARD +#define FLASH_LOADSIZE_SPI FLASH_LOADSIZE_STANDARD +#define FLASH_LOADSIZE_ONENAND 0x400 +#define FLASH_LOADSIZE_NOR 0x0 /* entire image */ +#define FLASH_LOADSIZE_SATA FLASH_LOADSIZE_STANDARD + #define IVT_HEADER_TAG 0xD1 #define IVT_VERSION 0x40 #define DCD_HEADER_TAG 0xD2 @@ -147,7 +157,7 @@ struct imx_header { imx_header_v1_t hdr_v1; imx_header_v2_t hdr_v2; } header; -} __attribute__((aligned(4096))); +}; typedef void (*set_dcd_val_t)(struct imx_header *imxhdr, char *name, int lineno, -- cgit v0.10.2 From 9bac0bb37402ca72fd905f3e591080b4cfb98c42 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Mon, 19 Aug 2013 19:03:19 +0200 Subject: tools: add variable padding of data image in mkimage Use previously unused return value of function vrec_header to return a padding size to generic mkimage. This padding size is used in copy_files to pad with zeros after copying the data image. Signed-off-by: Stefano Babic diff --git a/tools/mkimage.c b/tools/mkimage.c index b700b9e..58d25fa 100644 --- a/tools/mkimage.c +++ b/tools/mkimage.c @@ -137,6 +137,7 @@ main (int argc, char **argv) char *ptr; int retval = 0; struct image_type_params *tparams = NULL; + int pad_len = 0; /* Init Freescale PBL Boot image generation/list support */ init_pbl_image_type(); @@ -391,7 +392,7 @@ NXTARG: ; * allocate memory for the header itself. */ if (tparams->vrec_header) - tparams->vrec_header(¶ms, tparams); + pad_len = tparams->vrec_header(¶ms, tparams); else memset(tparams->hdr, 0, tparams->header_size); @@ -463,7 +464,7 @@ NXTARG: ; /* PBL has special Image format, implements its' own */ pbl_load_uboot(ifd, ¶ms); } else { - copy_file (ifd, params.datafile, 0); + copy_file(ifd, params.datafile, pad_len); } } @@ -537,10 +538,19 @@ copy_file (int ifd, const char *datafile, int pad) unsigned char *ptr; int tail; int zero = 0; + uint8_t zeros[4096]; int offset = 0; int size; struct image_type_params *tparams = mkimage_get_type (params.type); + if (pad >= sizeof(zeros)) { + fprintf(stderr, "%s: Can't pad to %d\n", + params.cmdname, pad); + exit(EXIT_FAILURE); + } + + memset(zeros, 0, sizeof(zeros)); + if (params.vflag) { fprintf (stderr, "Adding Image %s\n", datafile); } @@ -598,7 +608,8 @@ copy_file (int ifd, const char *datafile, int pad) exit (EXIT_FAILURE); } - if (pad && ((tail = size % 4) != 0)) { + tail = size % 4; + if ((pad == 1) && (tail != 0)) { if (write(ifd, (char *)&zero, 4-tail) != 4-tail) { fprintf (stderr, "%s: Write error on %s: %s\n", @@ -606,6 +617,13 @@ copy_file (int ifd, const char *datafile, int pad) strerror(errno)); exit (EXIT_FAILURE); } + } else if (pad > 1) { + if (write(ifd, (char *)&zeros, pad) != pad) { + fprintf(stderr, "%s: Write error on %s: %s\n", + params.cmdname, params.imagefile, + strerror(errno)); + exit(EXIT_FAILURE); + } } (void) munmap((void *)ptr, sbuf.st_size); diff --git a/tools/mkimage.h b/tools/mkimage.h index 950e190..ecb3032 100644 --- a/tools/mkimage.h +++ b/tools/mkimage.h @@ -132,7 +132,10 @@ struct image_type_params { /* * This callback function will be executed for variable size record * It is expected to build this header in memory and return its length - * and a pointer to it + * and a pointer to it by using image_type_params.header_size and + * image_type_params.hdr. The return value shall indicate if an + * additional padding should be used when copying the data image + * by returning the padding length. */ int (*vrec_header) (struct mkimage_params *, struct image_type_params *); -- cgit v0.10.2 From 01390aff251e541fcaa77fa6c6e3eee4d7a5554b Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Mon, 19 Aug 2013 19:03:20 +0200 Subject: tools: add padding of data image file for imximage Implement function vrec_header to be able to pad the final data image file according the what has been calculated for boot_data.length. Signed-off-by: Stefano Babic diff --git a/tools/imximage.c b/tools/imximage.c index 2b4909e..26460bf 100644 --- a/tools/imximage.c +++ b/tools/imximage.c @@ -365,6 +365,13 @@ static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, name, lineno, token); exit(EXIT_FAILURE); } + + /* + * The SOC loads from the storage starting at address 0 + * then ensures that the load size contains the offset + */ + if (imximage_init_loadsize < imximage_ivt_offset) + imximage_init_loadsize = imximage_ivt_offset; if (unlikely(cmd_ver_first != 1)) cmd_ver_first = 0; break; @@ -439,7 +446,8 @@ static uint32_t parse_cfg_file(struct imx_header *imxhdr, char *name) exit(EXIT_FAILURE); } - /* Very simple parsing, line starting with # are comments + /* + * Very simple parsing, line starting with # are comments * and are dropped */ while ((getline(&line, &len, fd)) > 0) { @@ -571,18 +579,92 @@ int imximage_check_params(struct mkimage_params *params) (params->xflag) || !(strlen(params->imagename)); } +static int imximage_generate(struct mkimage_params *params, + struct image_type_params *tparams) +{ + struct imx_header *imxhdr; + size_t alloc_len; + struct stat sbuf; + char *datafile = params->datafile; + uint32_t pad_len; + + memset(&imximage_header, 0, sizeof(imximage_header)); + + /* + * In order to not change the old imx cfg file + * by adding VERSION command into it, here need + * set up function ptr group to V1 by default. + */ + imximage_version = IMXIMAGE_V1; + /* Be able to detect if the cfg file has no BOOT_FROM tag */ + imximage_ivt_offset = FLASH_OFFSET_UNDEFINED; + imximage_csf_size = 0; + set_hdr_func(imxhdr); + + /* Parse dcd configuration file */ + parse_cfg_file(&imximage_header, params->imagename); + + /* TODO: check i.MX image V1 handling, for now use 'old' style */ + if (imximage_version == IMXIMAGE_V1) { + alloc_len = 4096; + } else { + if (imximage_init_loadsize < imximage_ivt_offset + + sizeof(imx_header_v2_t)) + imximage_init_loadsize = imximage_ivt_offset + + sizeof(imx_header_v2_t); + alloc_len = imximage_init_loadsize - imximage_ivt_offset; + } + + if (alloc_len < sizeof(struct imx_header)) { + fprintf(stderr, "%s: header error\n", + params->cmdname); + exit(EXIT_FAILURE); + } + + imxhdr = malloc(alloc_len); + + if (!imxhdr) { + fprintf(stderr, "%s: malloc return failure: %s\n", + params->cmdname, strerror(errno)); + exit(EXIT_FAILURE); + } + + memset(imxhdr, 0, alloc_len); + + tparams->header_size = alloc_len; + tparams->hdr = imxhdr; + + /* determine data image file length */ + + if (stat(datafile, &sbuf) < 0) { + fprintf(stderr, "%s: Can't stat %s: %s\n", + params->cmdname, datafile, strerror(errno)); + exit(EXIT_FAILURE); + } + + pad_len = ROUND(sbuf.st_size, 4096) - sbuf.st_size; + + /* TODO: check i.MX image V1 handling, for now use 'old' style */ + if (imximage_version == IMXIMAGE_V1) + return 0; + else + return pad_len; +} + + /* * imximage parameters */ static struct image_type_params imximage_params = { .name = "Freescale i.MX Boot Image support", - .header_size = sizeof(struct imx_header), - .hdr = (void *)&imximage_header, + .header_size = 0, + .hdr = NULL, .check_image_type = imximage_check_image_types, .verify_header = imximage_verify_header, .print_header = imximage_print_header, .set_header = imximage_set_header, .check_params = imximage_check_params, + .vrec_header = imximage_generate, }; void init_imx_image_type(void) -- cgit v0.10.2 From 0187c985aa870a74caeecd3bd10244322b7e4d99 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Thu, 27 Jun 2013 11:42:38 +0200 Subject: tools: add support for setting the CSF into imximage Add support for setting the CSF (Command Sequence File) pointer which is used for HAB (High Assurance Boot) in the imximage by adding e.g. CSF 0x2000 in the imximage.cfg file. This will set the CSF pointer accordingly just after the padded data image area. The boot_data.length is adjusted with the value from the imximage.cfg config file. The resulting u-boot.imx can be signed with the FSL HAB tooling. The generated CSF block needs to be appended to the u-boot.imx. Signed-off-by: Stefano Babic diff --git a/doc/README.imximage b/doc/README.imximage index 802eb90..dcda200 100644 --- a/doc/README.imximage +++ b/doc/README.imximage @@ -15,9 +15,6 @@ Booting from NOR flash does not require to use this image type. For more details refer Chapter 2 - System Boot and section 2.14 (flash header description) of the processor's manual. -This implementation does not use at the moment the secure boot feature -of the processor. The image is generated disabling all security fields. - Command syntax: -------------- ./tools/mkimage -l @@ -86,6 +83,33 @@ Configuration command line syntax: Example: BOOT_FROM spi + CSF value + + Total size of CSF (Command Sequence File) + used for Secure Boot/ High Assurance Boot + (HAB). + + Using this command will populate the IVT + (Initial Vector Table) CSF pointer and adjust + the length fields only. The CSF itself needs + to be generated with Freescale tools and + 'manually' appended to the u-boot.imx file. + + The CSF is then simply concatenated + to the u-boot image, making a signed bootloader, + that the processor can verify + if the fuses for the keys are burned. + + Further infos how to configure the SOC to verify + the bootloader can be found in the "High + Assurance Boot Version Application Programming + Interface Reference Manual" as part of the + Freescale Code Signing Tool, available on the + manufacturer's website. + + Example: + CSF 0x2000 + DATA type address value type: word=4, halfword=2, byte=1 diff --git a/doc/README.mxc_hab b/doc/README.mxc_hab new file mode 100644 index 0000000..97f8b7d --- /dev/null +++ b/doc/README.mxc_hab @@ -0,0 +1,48 @@ +High Assurance Boot (HAB) for i.MX6 CPUs + +To authenticate U-Boot only by the CPU there is no code required in +U-Boot itself. However, the U-Boot image to be programmed into the +boot media needs to be properly constructed, i.e. it must contain a +proper Command Sequence File (CSF). + +The Initial Vector Table contains a pointer to the CSF. Please see +doc/README.imximage for how to prepare u-boot.imx. + +The CSF itself is being generated by Freescale HAB tools. + +mkimage will output additional information about "HAB Blocks" +which can be used in the Freescale tooling to authenticate U-Boot +(entries in the CSF file). + +Image Type: Freescale IMX Boot Image +Image Ver: 2 (i.MX53/6 compatible) +Data Size: 327680 Bytes = 320.00 kB = 0.31 MB +Load Address: 177ff420 +Entry Point: 17800000 +HAB Blocks: 177ff400 00000000 0004dc00 + ^^^^^^^^ ^^^^^^^^ ^^^^^^^^ + | | | + | | -------- (1) + | | + | ------------------- (2) + | + --------------------------- (3) + +(1) Size of area in file u-boot.imx to sign + This area should include the IVT, the Boot Data the DCD + and U-Boot itself. +(2) Start of area in u-boot.imx to sign +(3) Start of area in RAM to authenticate + +CONFIG_SECURE_BOOT currently enables only an additional command +'hab_status' in U-Boot to retrieve the HAB status and events. This +can be useful while developing and testing HAB. + +Commands to generate a signed U-Boot using Freescale HAB tools: +cst --o U-Boot_CSF.bin < U-Boot.CSF +objcopy -I binary -O binary --pad-to 0x2000 --gap-fill=0x00 \ + U-Boot_CSF.bin U-Boot_CSF_pad.bin +cat u-boot.imx U-Boot_CSF_pad.bin > u-boot-signed.imx + +NOTE: U-Boot_CSF.bin needs to be padded to the value specified in +the imximage.cfg file. diff --git a/tools/imximage.c b/tools/imximage.c index 26460bf..3f2dc68 100644 --- a/tools/imximage.c +++ b/tools/imximage.c @@ -16,6 +16,8 @@ #include #include "imximage.h" +#define UNDEFINED 0xFFFFFFFF + /* * Supported commands for configuration file */ @@ -23,6 +25,7 @@ static table_entry_t imximage_cmds[] = { {CMD_BOOT_FROM, "BOOT_FROM", "boot command", }, {CMD_BOOT_OFFSET, "BOOT_OFFSET", "Boot offset", }, {CMD_DATA, "DATA", "Reg Write Data", }, + {CMD_CSF, "CSF", "Command Sequence File", }, {CMD_IMAGE_VERSION, "IMAGE_VERSION", "image version", }, {-1, "", "", }, }; @@ -66,8 +69,13 @@ static table_entry_t imximage_versions[] = { static struct imx_header imximage_header; static uint32_t imximage_version; -/* Image Vector Table Offset */ -static uint32_t imximage_ivt_offset; +/* + * Image Vector Table Offset + * Initialized to a wrong not 4-bytes aligned address to + * check if it is was set by the cfg file. + */ +static uint32_t imximage_ivt_offset = UNDEFINED; +static uint32_t imximage_csf_size = UNDEFINED; /* Initial Load Region Size */ static uint32_t imximage_init_loadsize; @@ -76,6 +84,7 @@ static set_dcd_rst_t set_dcd_rst; static set_imx_hdr_t set_imx_hdr; static uint32_t max_dcd_entries; static uint32_t *header_size_ptr; +static uint32_t *csf_ptr; static uint32_t get_cfg_value(char *token, char *name, int linenr) { @@ -247,9 +256,10 @@ static void set_imx_hdr_v2(struct imx_header *imxhdr, uint32_t dcd_len, + offsetof(imx_header_v2_t, boot_data); hdr_v2->boot_data.start = entry_point - imximage_init_loadsize; - /* Security feature are not supported */ fhdr_v2->csf = 0; + header_size_ptr = &hdr_v2->boot_data.size; + csf_ptr = &fhdr_v2->csf; } static void set_hdr_func(struct imx_header *imxhdr) @@ -326,6 +336,13 @@ static void print_hdr_v2(struct imx_header *imx_hdr) genimg_print_size(hdr_v2->boot_data.size); printf("Load Address: %08x\n", (uint32_t)fhdr_v2->boot_data_ptr); printf("Entry Point: %08x\n", (uint32_t)fhdr_v2->entry); + if (fhdr_v2->csf && (imximage_ivt_offset != UNDEFINED) && + (imximage_csf_size != UNDEFINED)) { + printf("HAB Blocks: %08x %08x %08x\n", + (uint32_t)fhdr_v2->self, 0, + hdr_v2->boot_data.size - imximage_ivt_offset - + imximage_csf_size); + } } static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, @@ -386,6 +403,17 @@ static void parse_cfg_cmd(struct imx_header *imxhdr, int32_t cmd, char *token, if (unlikely(cmd_ver_first != 1)) cmd_ver_first = 0; break; + case CMD_CSF: + if (imximage_version != 2) { + fprintf(stderr, + "Error: %s[%d] - CSF only supported for VERSION 2(%s)\n", + name, lineno, token); + exit(EXIT_FAILURE); + } + imximage_csf_size = get_cfg_value(token, name, lineno); + if (unlikely(cmd_ver_first != 1)) + cmd_ver_first = 0; + break; } } @@ -537,6 +565,7 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, imximage_version = IMXIMAGE_V1; /* Be able to detect if the cfg file has no BOOT_FROM tag */ imximage_ivt_offset = FLASH_OFFSET_UNDEFINED; + imximage_csf_size = 0; set_hdr_func(imxhdr); /* Parse dcd configuration file */ @@ -555,6 +584,12 @@ static void imximage_set_header(void *ptr, struct stat *sbuf, int ifd, * The remaining fraction of a block bytes would not be loaded! */ *header_size_ptr = ROUND(sbuf->st_size, 4096); + + if (csf_ptr && imximage_csf_size) { + *csf_ptr = params->ep - imximage_init_loadsize + + *header_size_ptr; + *header_size_ptr += imximage_csf_size; + } } int imximage_check_params(struct mkimage_params *params) diff --git a/tools/imximage.h b/tools/imximage.h index bb04a43..efe6a88 100644 --- a/tools/imximage.h +++ b/tools/imximage.h @@ -52,7 +52,8 @@ enum imximage_cmd { CMD_IMAGE_VERSION, CMD_BOOT_FROM, CMD_BOOT_OFFSET, - CMD_DATA + CMD_DATA, + CMD_CSF, }; enum imximage_fld_types { -- cgit v0.10.2 From b83c709e8d3f29721f32d66f19f953a2f818afbc Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Fri, 28 Jun 2013 00:20:21 +0200 Subject: imx: add status reporting for HAB status Add functions to report the HAB (High Assurance Boot) status of e.g. i.MX6 CPUs. This is taken from git://git.freescale.com/imx/uboot-imx.git branch imx_v2009.08_3.0.35_4.0.0 cpu/arm_cortexa8/mx6/generic.c include/asm-arm/arch-mx6/mx6_secure.h Signed-off-by: Stefano Babic diff --git a/arch/arm/cpu/armv7/mx6/Makefile b/arch/arm/cpu/armv7/mx6/Makefile index c5e9858..6d73617 100644 --- a/arch/arm/cpu/armv7/mx6/Makefile +++ b/arch/arm/cpu/armv7/mx6/Makefile @@ -11,10 +11,11 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(SOC).o -COBJS = soc.o clock.o +COBJS-y = soc.o clock.o +COBJS-$(CONFIG_SECURE_BOOT) += hab.o -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y)) all: $(obj).depend $(LIB) diff --git a/arch/arm/cpu/armv7/mx6/hab.c b/arch/arm/cpu/armv7/mx6/hab.c new file mode 100644 index 0000000..5187775 --- /dev/null +++ b/arch/arm/cpu/armv7/mx6/hab.c @@ -0,0 +1,104 @@ +/* + * Copyright (C) 2010-2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include + +/* -------- start of HAB API updates ------------*/ +#define hab_rvt_report_event ((hab_rvt_report_event_t *)HAB_RVT_REPORT_EVENT) +#define hab_rvt_report_status ((hab_rvt_report_status_t *)HAB_RVT_REPORT_STATUS) +#define hab_rvt_authenticate_image \ + ((hab_rvt_authenticate_image_t *)HAB_RVT_AUTHENTICATE_IMAGE) +#define hab_rvt_entry ((hab_rvt_entry_t *)HAB_RVT_ENTRY) +#define hab_rvt_exit ((hab_rvt_exit_t *)HAB_RVT_EXIT) +#define hab_rvt_clock_init HAB_RVT_CLOCK_INIT + +bool is_hab_enabled(void) +{ + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; + struct fuse_bank *bank = &ocotp->bank[0]; + struct fuse_bank0_regs *fuse = + (struct fuse_bank0_regs *)bank->fuse_regs; + uint32_t reg = readl(&fuse->cfg5); + + return (reg & 0x2) == 0x2; +} + +void display_event(uint8_t *event_data, size_t bytes) +{ + uint32_t i; + + if (!(event_data && bytes > 0)) + return; + + for (i = 0; i < bytes; i++) { + if (i == 0) + printf("\t0x%02x", event_data[i]); + else if ((i % 8) == 0) + printf("\n\t0x%02x", event_data[i]); + else + printf(" 0x%02x", event_data[i]); + } +} + +int get_hab_status(void) +{ + uint32_t index = 0; /* Loop index */ + uint8_t event_data[128]; /* Event data buffer */ + size_t bytes = sizeof(event_data); /* Event size in bytes */ + enum hab_config config = 0; + enum hab_state state = 0; + + if (is_hab_enabled()) + puts("\nSecure boot enabled\n"); + else + puts("\nSecure boot disabled\n"); + + /* Check HAB status */ + if (hab_rvt_report_status(&config, &state) != HAB_SUCCESS) { + printf("\nHAB Configuration: 0x%02x, HAB State: 0x%02x\n", + config, state); + + /* Display HAB Error events */ + while (hab_rvt_report_event(HAB_FAILURE, index, event_data, + &bytes) == HAB_SUCCESS) { + puts("\n"); + printf("--------- HAB Event %d -----------------\n", + index + 1); + puts("event data:\n"); + display_event(event_data, bytes); + puts("\n"); + bytes = sizeof(event_data); + index++; + } + } + /* Display message if no HAB events are found */ + else { + printf("\nHAB Configuration: 0x%02x, HAB State: 0x%02x\n", + config, state); + puts("No HAB Events Found!\n\n"); + } + return 0; +} + +int do_hab_status(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + if ((argc != 1)) { + cmd_usage(cmdtp); + return 1; + } + + get_hab_status(); + + return 0; +} + +U_BOOT_CMD( + hab_status, CONFIG_SYS_MAXARGS, 1, do_hab_status, + "display HAB status", + "" + ); diff --git a/arch/arm/include/asm/arch-mx6/hab.h b/arch/arm/include/asm/arch-mx6/hab.h new file mode 100644 index 0000000..d724f20 --- /dev/null +++ b/arch/arm/include/asm/arch-mx6/hab.h @@ -0,0 +1,67 @@ +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. All Rights Reserved. + * + * SPDX-License-Identifier: GPL-2.0+ + * +*/ + +#ifndef __SECURE_MX6Q_H__ +#define __SECURE_MX6Q_H__ + +#include + +/* -------- start of HAB API updates ------------*/ +/* The following are taken from HAB4 SIS */ + +/* Status definitions */ +enum hab_status { + HAB_STS_ANY = 0x00, + HAB_FAILURE = 0x33, + HAB_WARNING = 0x69, + HAB_SUCCESS = 0xf0 +}; + +/* Security Configuration definitions */ +enum hab_config { + HAB_CFG_RETURN = 0x33, /**< Field Return IC */ + HAB_CFG_OPEN = 0xf0, /**< Non-secure IC */ + HAB_CFG_CLOSED = 0xcc /**< Secure IC */ +}; + +/* State definitions */ +enum hab_state { + HAB_STATE_INITIAL = 0x33, /**< Initialising state (transitory) */ + HAB_STATE_CHECK = 0x55, /**< Check state (non-secure) */ + HAB_STATE_NONSECURE = 0x66, /**< Non-secure state */ + HAB_STATE_TRUSTED = 0x99, /**< Trusted state */ + HAB_STATE_SECURE = 0xaa, /**< Secure state */ + HAB_STATE_FAIL_SOFT = 0xcc, /**< Soft fail state */ + HAB_STATE_FAIL_HARD = 0xff, /**< Hard fail state (terminal) */ + HAB_STATE_NONE = 0xf0, /**< No security state machine */ + HAB_STATE_MAX +}; + +/*Function prototype description*/ +typedef enum hab_status hab_rvt_report_event_t(enum hab_status, uint32_t, + uint8_t* , size_t*); +typedef enum hab_status hab_rvt_report_status_t(enum hab_config *, + enum hab_state *); +typedef enum hab_status hab_loader_callback_f_t(void**, size_t*, const void*); +typedef enum hab_status hab_rvt_entry_t(void); +typedef enum hab_status hab_rvt_exit_t(void); +typedef void *hab_rvt_authenticate_image_t(uint8_t, ptrdiff_t, + void **, size_t *, hab_loader_callback_f_t); +typedef void hapi_clock_init_t(void); + +#define HAB_RVT_REPORT_EVENT (*(uint32_t *)0x000000B4) +#define HAB_RVT_REPORT_STATUS (*(uint32_t *)0x000000B8) +#define HAB_RVT_AUTHENTICATE_IMAGE (*(uint32_t *)0x000000A4) +#define HAB_RVT_ENTRY (*(uint32_t *)0x00000098) +#define HAB_RVT_EXIT (*(uint32_t *)0x0000009C) +#define HAB_RVT_CLOCK_INIT ((hapi_clock_init_t *)0x0000024D) + +#define HAB_CID_ROM 0 /**< ROM Caller ID */ +#define HAB_CID_UBOOT 1 /**< UBOOT Caller ID*/ +/* ----------- end of HAB API updates ------------*/ + +#endif diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h index 5d6bccb..621919f 100644 --- a/arch/arm/include/asm/arch-mx6/imx-regs.h +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h @@ -456,7 +456,13 @@ struct fuse_bank0_regs { u32 uid_low; u32 rsvd1[3]; u32 uid_high; - u32 rsvd2[0x17]; + u32 rsvd2[3]; + u32 rsvd3[4]; + u32 rsvd4[4]; + u32 rsvd5[4]; + u32 cfg5; + u32 rsvd6[3]; + u32 rsvd7[4]; }; struct fuse_bank4_regs { -- cgit v0.10.2 From bce8837071617a13f8e28f60400ee826b3f8a308 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Mon, 26 Aug 2013 20:43:33 +0200 Subject: ARM: mxs: tools: Add mkimage support for MXS bootstream Add mkimage support for generating and verifying MXS bootstream. The implementation here is mostly a glue code between MXSSB v0.4 and mkimage, but the long-term goal is to rectify this and merge MXSSB with mkimage more tightly. Once this code is properly in U-Boot, MXSSB shall be deprecated in favor of mkimage-mxsimage support. Note that the mxsimage generator needs libcrypto from OpenSSL, I therefore enabled the libcrypto/libssl unconditionally. MXSSB: http://git.denx.de/?p=mxssb.git;a=summary The code is based on research presented at: http://www.rockbox.org/wiki/SbFileFormat Signed-off-by: Marek Vasut Cc: Tom Rini Cc: Fabio Estevam Cc: Stefano Babic Cc: Otavio Salvador diff --git a/arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg b/arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg new file mode 100644 index 0000000..8118767 --- /dev/null +++ b/arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg @@ -0,0 +1,6 @@ +SECTION 0x0 BOOTABLE + TAG LAST + LOAD 0x0 spl/u-boot-spl.bin + CALL 0x14 0x0 + LOAD 0x40000100 u-boot.bin + CALL 0x40000100 0x0 diff --git a/arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg b/arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg new file mode 100644 index 0000000..ea772f0 --- /dev/null +++ b/arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg @@ -0,0 +1,8 @@ +SECTION 0x0 BOOTABLE + TAG LAST + LOAD 0x0 spl/u-boot-spl.bin + LOAD IVT 0x8000 0x14 + CALL HAB 0x8000 0x0 + LOAD 0x40000100 u-boot.bin + LOAD IVT 0x8000 0x40000100 + CALL HAB 0x8000 0x0 diff --git a/common/image.c b/common/image.c index 56a5a62..2c88091 100644 --- a/common/image.c +++ b/common/image.c @@ -135,6 +135,7 @@ static const table_entry_t uimage_type[] = { { IH_TYPE_SCRIPT, "script", "Script", }, { IH_TYPE_STANDALONE, "standalone", "Standalone Program", }, { IH_TYPE_UBLIMAGE, "ublimage", "Davinci UBL image",}, + { IH_TYPE_MXSIMAGE, "mxsimage", "Freescale MXS Boot Image",}, { -1, "", "", }, }; diff --git a/config.mk b/config.mk index 499eed1..3b92f56 100644 --- a/config.mk +++ b/config.mk @@ -194,6 +194,15 @@ LDFLAGS_FINAL += --gc-sections endif # TODO(sjg@chromium.org): Is this correct on Mac OS? + +# MXSImage needs LibSSL +ifneq ($(CONFIG_MX23)$(CONFIG_MX28),) +HOSTLIBS += -lssl -lcrypto +# Add CONFIG_MXS into host CFLAGS, so we can check whether or not register +# the mxsimage support within tools/mxsimage.c . +HOSTCFLAGS += -DCONFIG_MXS +endif + ifdef CONFIG_FIT_SIGNATURE HOSTLIBS += -lssl -lcrypto diff --git a/doc/README.mxsimage b/doc/README.mxsimage new file mode 100644 index 0000000..88a2caf --- /dev/null +++ b/doc/README.mxsimage @@ -0,0 +1,165 @@ +Freescale i.MX233/i.MX28 SB image generator via mkimage +======================================================= + +This tool allows user to produce SB BootStream encrypted with a zero key. +Such a BootStream is then bootable on i.MX23/i.MX28. + +Usage -- producing image: +========================= +The mxsimage tool is targeted to be a simple replacement for the elftosb2 . +To generate an image, write an image configuration file and run: + + mkimage -A arm -O u-boot -T mxsimage -n \ + + +The output bootstream file is usually using the .sb file extension. Note +that the example configuration files for producing bootable BootStream with +the U-Boot bootloader can be found under arch/arm/boot/cpu/arm926ejs/mxs/ +directory. See the following files: + + mxsimage.mx23.cfg -- This is an example configuration for i.MX23 + mxsimage.mx28.cfg -- This is an example configuration for i.MX28 + +Each configuration file uses very simple instruction semantics and a few +additional rules have to be followed so that a useful image can be produced. +These semantics and rules will be outlined now. + +- Each line of the configuration file contains exactly one instruction. +- Every numeric value must be encoded in hexadecimal and in format 0xabcdef12 . +- The configuration file is a concatenation of blocks called "sections" and + optionally "DCD blocks" (see below). + - Each "section" is started by the "SECTION" instruction. + - The "SECTION" instruction has the following semantics: + + SECTION u32_section_number [BOOTABLE] + - u32_section_number :: User-selected ID of the section + - BOOTABLE :: Sets the section as bootable + + - A bootable section is one from which the BootROM starts executing + subsequent instructions or code. Exactly one section must be selected + as bootable, usually the one containing the instructions and data to + load the bootloader. + + - A "SECTION" must be immediatelly followed by a "TAG" instruction. + - The "TAG" instruction has the following semantics: + + TAG [LAST] + - LAST :: Flag denoting the last section in the file + + - After a "TAG" unstruction, any of the following instructions may follow + in any order and any quantity: + + NOOP + - This instruction does nothing + + LOAD u32_address string_filename + - Instructs the BootROM to load file pointed by "string_filename" onto + address "u32_address". + + LOAD IVT u32_address u32_IVT_entry_point + - Crafts and loads IVT onto address "u32_address" with the entry point + of u32_IVT_entry_point. + - i.MX28-specific instruction! + + LOAD DCD u32_address u32_DCD_block_ID + - Loads the DCD block with ID "u32_DCD_block_ID" onto address + "u32_address" and executes the contents of this DCD block + - i.MX28-specific instruction! + + FILL u32_address u32_pattern u32_length + - Starts to write memory from addres "u32_address" with a pattern + specified by "u32_pattern". Writes exactly "u32_length" bytes of the + pattern. + + JUMP [HAB] u32_address [u32_r0_arg] + - Jumps onto memory address specified by "u32_address" by setting this + address in PT. The BootROM will pass the "u32_r0_arg" value in ARM + register "r0" to the executed code if this option is specified. + Otherwise, ARM register "r0" will default to value 0x00000000. The + optional "HAB" flag is i.MX28-specific flag turning on the HAB boot. + + CALL [HAB] u32_address [u32_r0_arg] + - See JUMP instruction above, as the operation is exactly the same with + one difference. The CALL instruction does allow returning into the + BootROM from the executed code. U-Boot makes use of this in it's SPL + code. + + MODE string_mode + - Restart the CPU and start booting from device specified by the + "string_mode" argument. The "string_mode" differs for each CPU + and can be: + i.MX23, string_mode = USB/I2C/SPI1_FLASH/SPI2_FLASH/NAND_BCH + JTAG/SPI3_EEPROM/SD_SSP0/SD_SSP1 + i.MX28, string_mode = USB/I2C/SPI2_FLASH/SPI3_FLASH/NAND_BCH + JTAG/SPI2_EEPROM/SD_SSP0/SD_SSP1 + + - An optional "DCD" blocks can be added at the begining of the configuration + file. Note that the DCD is only supported on i.MX28. + - The DCD blocks must be inserted before the first "section" in the + configuration file. + - The DCD block has the following semantics: + + DCD u32_DCD_block_ID + - u32_DCD_block_ID :: The ID number of the DCD block, must match + the ID number used by "LOAD DCD" instruction. + + - The DCD block must be followed by one of the following instructions. All + of the instructions operate either on 1, 2 or 4 bytes. This is selected by + the 'n' suffix of the instruction: + + WRITE.n u32_address u32_value + - Write the "u32_value" to the "u32_address" address. + + ORR.n u32_address u32_value + - Read the "u32_address", perform a bitwise-OR with the "u32_value" and + write the result back to "u32_address". + + ANDC.n u32_address u32_value + - Read the "u32_address", perform a bitwise-AND with the complement of + "u32_value" and write the result back to "u32_address". + + EQZ.n u32_address u32_count + - Read the "u32_address" at most "u32_count" times and test if the value + read is zero. If it is, break the loop earlier. + + NEZ.n u32_address u32_count + - Read the "u32_address" at most "u32_count" times and test if the value + read is non-zero. If it is, break the loop earlier. + + EQ.n u32_address u32_mask + - Read the "u32_address" in a loop and test if the result masked with + "u32_mask" equals the "u32_mask". If the values are equal, break the + reading loop. + + NEQ.n u32_address u32_mask + - Read the "u32_address" in a loop and test if the result masked with + "u32_mask" does not equal the "u32_mask". If the values are not equal, + break the reading loop. + + NOOP + - This instruction does nothing. + +- If the verbose output from the BootROM is enabled, the BootROM will produce a + letter on the Debug UART for each instruction it started processing. Here is a + mapping between the above instructions and the BootROM verbose output: + + H -- SB Image header loaded + T -- TAG instruction + N -- NOOP instruction + L -- LOAD instruction + F -- FILL instruction + J -- JUMP instruction + C -- CALL instruction + M -- MODE instruction + +Usage -- verifying image: +========================= + +The mxsimage can also verify and dump contents of an image. Use the following +syntax to verify and dump contents of an image: + + mkimage -l + +This will output all the information from the SB image header and all the +instructions contained in the SB image. It will also check if the various +checksums in the SB image are correct. diff --git a/include/image.h b/include/image.h index f93a393..ee6eb8d 100644 --- a/include/image.h +++ b/include/image.h @@ -212,6 +212,7 @@ struct lmb; #define IH_TYPE_AISIMAGE 13 /* TI Davinci AIS Image */ #define IH_TYPE_KERNEL_NOLOAD 14 /* OS Kernel Image, can run from any load address */ #define IH_TYPE_PBLIMAGE 15 /* Freescale PBL Boot Image */ +#define IH_TYPE_MXSIMAGE 16 /* Freescale MXSBoot Image */ /* * Compression Types diff --git a/tools/Makefile b/tools/Makefile index 33fad6b..bbae5a2 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -83,6 +83,7 @@ NOPED_OBJ_FILES-y += aisimage.o NOPED_OBJ_FILES-y += kwbimage.o NOPED_OBJ_FILES-y += pblimage.o NOPED_OBJ_FILES-y += imximage.o +NOPED_OBJ_FILES-y += mxsimage.o NOPED_OBJ_FILES-y += image-host.o NOPED_OBJ_FILES-y += omapimage.o NOPED_OBJ_FILES-y += mkenvimage.o @@ -209,6 +210,7 @@ $(obj)mkimage$(SFX): $(obj)aisimage.o \ $(obj)image-host.o \ $(FIT_SIG_OBJS) \ $(obj)imximage.o \ + $(obj)mxsimage.o \ $(obj)kwbimage.o \ $(obj)pblimage.o \ $(obj)md5.o \ diff --git a/tools/mkimage.c b/tools/mkimage.c index 58d25fa..7f22101 100644 --- a/tools/mkimage.c +++ b/tools/mkimage.c @@ -145,6 +145,8 @@ main (int argc, char **argv) init_kwb_image_type (); /* Init Freescale imx Boot image generation/list support */ init_imx_image_type (); + /* Init Freescale mxs Boot image generation/list support */ + init_mxs_image_type(); /* Init FIT image generation/list support */ init_fit_image_type (); /* Init TI OMAP Boot image generation/list support */ diff --git a/tools/mkimage.h b/tools/mkimage.h index ecb3032..af49154 100644 --- a/tools/mkimage.h +++ b/tools/mkimage.h @@ -161,6 +161,7 @@ void init_pbl_image_type(void); void init_ais_image_type(void); void init_kwb_image_type (void); void init_imx_image_type (void); +void init_mxs_image_type(void); void init_default_image_type (void); void init_fit_image_type (void); void init_ubl_image_type(void); diff --git a/tools/mxsimage.c b/tools/mxsimage.c new file mode 100644 index 0000000..5db19b2 --- /dev/null +++ b/tools/mxsimage.c @@ -0,0 +1,2347 @@ +/* + * Freescale i.MX23/i.MX28 SB image generator + * + * Copyright (C) 2012-2013 Marek Vasut + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifdef CONFIG_MXS + +#include +#include +#include +#include +#include +#include + +#include + +#include "mkimage.h" +#include "mxsimage.h" +#include + + +/* + * DCD block + * |-Write to address command block + * | 0xf00 == 0xf33d + * | 0xba2 == 0xb33f + * |-ORR address with mask command block + * | 0xf00 |= 0x1337 + * |-Write to address command block + * | 0xba2 == 0xd00d + * : + */ +#define SB_HAB_DCD_WRITE 0xccUL +#define SB_HAB_DCD_CHECK 0xcfUL +#define SB_HAB_DCD_NOOP 0xc0UL +#define SB_HAB_DCD_MASK_BIT (1 << 3) +#define SB_HAB_DCD_SET_BIT (1 << 4) + +/* Addr.n = Value.n */ +#define SB_DCD_WRITE \ + (SB_HAB_DCD_WRITE << 24) +/* Addr.n &= ~Value.n */ +#define SB_DCD_ANDC \ + ((SB_HAB_DCD_WRITE << 24) | SB_HAB_DCD_SET_BIT) +/* Addr.n |= Value.n */ +#define SB_DCD_ORR \ + ((SB_HAB_DCD_WRITE << 24) | SB_HAB_DCD_SET_BIT | SB_HAB_DCD_MASK_BIT) +/* (Addr.n & Value.n) == 0 */ +#define SB_DCD_CHK_EQZ \ + (SB_HAB_DCD_CHECK << 24) +/* (Addr.n & Value.n) == Value.n */ +#define SB_DCD_CHK_EQ \ + ((SB_HAB_DCD_CHECK << 24) | SB_HAB_DCD_SET_BIT) +/* (Addr.n & Value.n) != Value.n */ +#define SB_DCD_CHK_NEQ \ + ((SB_HAB_DCD_CHECK << 24) | SB_HAB_DCD_MASK_BIT) +/* (Addr.n & Value.n) != 0 */ +#define SB_DCD_CHK_NEZ \ + ((SB_HAB_DCD_CHECK << 24) | SB_HAB_DCD_SET_BIT | SB_HAB_DCD_MASK_BIT) +/* NOP */ +#define SB_DCD_NOOP \ + (SB_HAB_DCD_NOOP << 24) + +struct sb_dcd_ctx { + struct sb_dcd_ctx *dcd; + + uint32_t id; + + /* The DCD block. */ + uint32_t *payload; + /* Size of the whole DCD block. */ + uint32_t size; + + /* Pointer to previous DCD command block. */ + uint32_t *prev_dcd_head; +}; + +/* + * IMAGE + * |-SECTION + * | |-CMD + * | |-CMD + * | `-CMD + * |-SECTION + * | |-CMD + * : : + */ +struct sb_cmd_list { + char *cmd; + size_t len; + unsigned int lineno; +}; + +struct sb_cmd_ctx { + uint32_t size; + + struct sb_cmd_ctx *cmd; + + uint8_t *data; + uint32_t length; + + struct sb_command payload; + struct sb_command c_payload; +}; + +struct sb_section_ctx { + uint32_t size; + + /* Section flags */ + unsigned int boot:1; + + struct sb_section_ctx *sect; + + struct sb_cmd_ctx *cmd_head; + struct sb_cmd_ctx *cmd_tail; + + struct sb_sections_header payload; +}; + +struct sb_image_ctx { + unsigned int in_section:1; + unsigned int in_dcd:1; + /* Image configuration */ + unsigned int verbose_boot:1; + unsigned int silent_dump:1; + char *input_filename; + char *output_filename; + char *cfg_filename; + uint8_t image_key[16]; + + /* Number of section in the image */ + unsigned int sect_count; + /* Bootable section */ + unsigned int sect_boot; + unsigned int sect_boot_found:1; + + struct sb_section_ctx *sect_head; + struct sb_section_ctx *sect_tail; + + struct sb_dcd_ctx *dcd_head; + struct sb_dcd_ctx *dcd_tail; + + EVP_CIPHER_CTX cipher_ctx; + EVP_MD_CTX md_ctx; + uint8_t digest[32]; + struct sb_key_dictionary_key sb_dict_key; + + struct sb_boot_image_header payload; +}; + +/* + * Instruction semantics: + * NOOP + * TAG [LAST] + * LOAD address file + * LOAD IVT address IVT_entry_point + * FILL address pattern length + * JUMP [HAB] address [r0_arg] + * CALL [HAB] address [r0_arg] + * MODE mode + * For i.MX23, mode = USB/I2C/SPI1_FLASH/SPI2_FLASH/NAND_BCH + * JTAG/SPI3_EEPROM/SD_SSP0/SD_SSP1 + * For i.MX28, mode = USB/I2C/SPI2_FLASH/SPI3_FLASH/NAND_BCH + * JTAG/SPI2_EEPROM/SD_SSP0/SD_SSP1 + */ + +/* + * AES libcrypto + */ +static int sb_aes_init(struct sb_image_ctx *ictx, uint8_t *iv, int enc) +{ + EVP_CIPHER_CTX *ctx = &ictx->cipher_ctx; + int ret; + + /* If there is no init vector, init vector is all zeroes. */ + if (!iv) + iv = ictx->image_key; + + EVP_CIPHER_CTX_init(ctx); + ret = EVP_CipherInit(ctx, EVP_aes_128_cbc(), ictx->image_key, iv, enc); + if (ret == 1) + EVP_CIPHER_CTX_set_padding(ctx, 0); + return ret; +} + +static int sb_aes_crypt(struct sb_image_ctx *ictx, uint8_t *in_data, + uint8_t *out_data, int in_len) +{ + EVP_CIPHER_CTX *ctx = &ictx->cipher_ctx; + int ret, outlen; + uint8_t *outbuf; + + outbuf = malloc(in_len); + if (!outbuf) + return -ENOMEM; + memset(outbuf, 0, sizeof(in_len)); + + ret = EVP_CipherUpdate(ctx, outbuf, &outlen, in_data, in_len); + if (!ret) { + ret = -EINVAL; + goto err; + } + + if (out_data) + memcpy(out_data, outbuf, outlen); + +err: + free(outbuf); + return ret; +} + +static int sb_aes_deinit(EVP_CIPHER_CTX *ctx) +{ + return EVP_CIPHER_CTX_cleanup(ctx); +} + +static int sb_aes_reinit(struct sb_image_ctx *ictx, int enc) +{ + int ret; + EVP_CIPHER_CTX *ctx = &ictx->cipher_ctx; + struct sb_boot_image_header *sb_header = &ictx->payload; + uint8_t *iv = sb_header->iv; + + ret = sb_aes_deinit(ctx); + if (!ret) + return ret; + return sb_aes_init(ictx, iv, enc); +} + +/* + * CRC32 + */ +static uint32_t crc32(uint8_t *data, uint32_t len) +{ + const uint32_t poly = 0x04c11db7; + uint32_t crc32 = 0xffffffff; + unsigned int byte, bit; + + for (byte = 0; byte < len; byte++) { + crc32 ^= data[byte] << 24; + + for (bit = 8; bit > 0; bit--) { + if (crc32 & (1UL << 31)) + crc32 = (crc32 << 1) ^ poly; + else + crc32 = (crc32 << 1); + } + } + + return crc32; +} + +/* + * Debug + */ +static void soprintf(struct sb_image_ctx *ictx, const char *fmt, ...) +{ + va_list ap; + + if (ictx->silent_dump) + return; + + va_start(ap, fmt); + vfprintf(stdout, fmt, ap); + va_end(ap); +} + +/* + * Code + */ +static time_t sb_get_timestamp(void) +{ + struct tm time_2000 = { + .tm_yday = 1, /* Jan. 1st */ + .tm_year = 100, /* 2000 */ + }; + time_t seconds_to_2000 = mktime(&time_2000); + time_t seconds_to_now = time(NULL); + + return seconds_to_now - seconds_to_2000; +} + +static int sb_get_time(time_t time, struct tm *tm) +{ + struct tm time_2000 = { + .tm_yday = 1, /* Jan. 1st */ + .tm_year = 0, /* 1900 */ + }; + const time_t seconds_to_2000 = mktime(&time_2000); + const time_t seconds_to_now = seconds_to_2000 + time; + struct tm *ret; + ret = gmtime_r(&seconds_to_now, tm); + return ret ? 0 : -EINVAL; +} + +static void sb_encrypt_sb_header(struct sb_image_ctx *ictx) +{ + EVP_MD_CTX *md_ctx = &ictx->md_ctx; + struct sb_boot_image_header *sb_header = &ictx->payload; + uint8_t *sb_header_ptr = (uint8_t *)sb_header; + + /* Encrypt the header, compute the digest. */ + sb_aes_crypt(ictx, sb_header_ptr, NULL, sizeof(*sb_header)); + EVP_DigestUpdate(md_ctx, sb_header_ptr, sizeof(*sb_header)); +} + +static void sb_encrypt_sb_sections_header(struct sb_image_ctx *ictx) +{ + EVP_MD_CTX *md_ctx = &ictx->md_ctx; + struct sb_section_ctx *sctx = ictx->sect_head; + struct sb_sections_header *shdr; + uint8_t *sb_sections_header_ptr; + const int size = sizeof(*shdr); + + while (sctx) { + shdr = &sctx->payload; + sb_sections_header_ptr = (uint8_t *)shdr; + + sb_aes_crypt(ictx, sb_sections_header_ptr, + ictx->sb_dict_key.cbc_mac, size); + EVP_DigestUpdate(md_ctx, sb_sections_header_ptr, size); + + sctx = sctx->sect; + }; +} + +static void sb_encrypt_key_dictionary_key(struct sb_image_ctx *ictx) +{ + EVP_MD_CTX *md_ctx = &ictx->md_ctx; + + sb_aes_crypt(ictx, ictx->image_key, ictx->sb_dict_key.key, + sizeof(ictx->sb_dict_key.key)); + EVP_DigestUpdate(md_ctx, &ictx->sb_dict_key, sizeof(ictx->sb_dict_key)); +} + +static void sb_decrypt_key_dictionary_key(struct sb_image_ctx *ictx) +{ + EVP_MD_CTX *md_ctx = &ictx->md_ctx; + + EVP_DigestUpdate(md_ctx, &ictx->sb_dict_key, sizeof(ictx->sb_dict_key)); + sb_aes_crypt(ictx, ictx->sb_dict_key.key, ictx->image_key, + sizeof(ictx->sb_dict_key.key)); +} + +static void sb_encrypt_tag(struct sb_image_ctx *ictx, + struct sb_cmd_ctx *cctx) +{ + EVP_MD_CTX *md_ctx = &ictx->md_ctx; + struct sb_command *cmd = &cctx->payload; + + sb_aes_crypt(ictx, (uint8_t *)cmd, + (uint8_t *)&cctx->c_payload, sizeof(*cmd)); + EVP_DigestUpdate(md_ctx, &cctx->c_payload, sizeof(*cmd)); +} + +static int sb_encrypt_image(struct sb_image_ctx *ictx) +{ + /* Start image-wide crypto. */ + EVP_MD_CTX_init(&ictx->md_ctx); + EVP_DigestInit(&ictx->md_ctx, EVP_sha1()); + + /* + * SB image header. + */ + sb_aes_init(ictx, NULL, 1); + sb_encrypt_sb_header(ictx); + + /* + * SB sections header. + */ + sb_encrypt_sb_sections_header(ictx); + + /* + * Key dictionary. + */ + sb_aes_reinit(ictx, 1); + sb_encrypt_key_dictionary_key(ictx); + + /* + * Section tags. + */ + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + struct sb_section_ctx *sctx = ictx->sect_head; + + while (sctx) { + cctx = sctx->cmd_head; + + sb_aes_reinit(ictx, 1); + + while (cctx) { + ccmd = &cctx->payload; + + sb_encrypt_tag(ictx, cctx); + + if (ccmd->header.tag == ROM_TAG_CMD) { + sb_aes_reinit(ictx, 1); + } else if (ccmd->header.tag == ROM_LOAD_CMD) { + sb_aes_crypt(ictx, cctx->data, cctx->data, + cctx->length); + EVP_DigestUpdate(&ictx->md_ctx, cctx->data, + cctx->length); + } + + cctx = cctx->cmd; + } + + sctx = sctx->sect; + }; + + /* + * Dump the SHA1 of the whole image. + */ + sb_aes_reinit(ictx, 1); + + EVP_DigestFinal(&ictx->md_ctx, ictx->digest, NULL); + sb_aes_crypt(ictx, ictx->digest, ictx->digest, sizeof(ictx->digest)); + + /* Stop the encryption session. */ + sb_aes_deinit(&ictx->cipher_ctx); + + return 0; +} + +static int sb_load_file(struct sb_cmd_ctx *cctx, char *filename) +{ + long real_size, roundup_size; + uint8_t *data; + long ret; + unsigned long size; + FILE *fp; + + if (!filename) { + fprintf(stderr, "ERR: Missing filename!\n"); + return -EINVAL; + } + + fp = fopen(filename, "r"); + if (!fp) + goto err_open; + + ret = fseek(fp, 0, SEEK_END); + if (ret < 0) + goto err_file; + + real_size = ftell(fp); + if (real_size < 0) + goto err_file; + + ret = fseek(fp, 0, SEEK_SET); + if (ret < 0) + goto err_file; + + roundup_size = roundup(real_size, SB_BLOCK_SIZE); + data = calloc(1, roundup_size); + if (!data) + goto err_file; + + size = fread(data, 1, real_size, fp); + if (size != (unsigned long)real_size) + goto err_alloc; + + cctx->data = data; + cctx->length = roundup_size; + + fclose(fp); + return 0; + +err_alloc: + free(data); +err_file: + fclose(fp); +err_open: + fprintf(stderr, "ERR: Failed to load file \"%s\"\n", filename); + return -EINVAL; +} + +static uint8_t sb_command_checksum(struct sb_command *inst) +{ + uint8_t *inst_ptr = (uint8_t *)inst; + uint8_t csum = 0; + unsigned int i; + + for (i = 0; i < sizeof(struct sb_command); i++) + csum += inst_ptr[i]; + + return csum; +} + +static int sb_token_to_long(char *tok, uint32_t *rid) +{ + char *endptr; + unsigned long id; + + if (tok[0] != '0' || tok[1] != 'x') { + fprintf(stderr, "ERR: Invalid hexadecimal number!\n"); + return -EINVAL; + } + + tok += 2; + + id = strtoul(tok, &endptr, 16); + if ((errno == ERANGE && id == ULONG_MAX) || (errno != 0 && id == 0)) { + fprintf(stderr, "ERR: Value can't be decoded!\n"); + return -EINVAL; + } + + /* Check for 32-bit overflow. */ + if (id > 0xffffffff) { + fprintf(stderr, "ERR: Value too big!\n"); + return -EINVAL; + } + + if (endptr == tok) { + fprintf(stderr, "ERR: Deformed value!\n"); + return -EINVAL; + } + + *rid = (uint32_t)id; + return 0; +} + +static int sb_grow_dcd(struct sb_dcd_ctx *dctx, unsigned int inc_size) +{ + uint32_t *tmp; + + if (!inc_size) + return 0; + + dctx->size += inc_size; + tmp = realloc(dctx->payload, dctx->size); + if (!tmp) + return -ENOMEM; + + dctx->payload = tmp; + + /* Assemble and update the HAB DCD header. */ + dctx->payload[0] = htonl((SB_HAB_DCD_TAG << 24) | + (dctx->size << 8) | + SB_HAB_VERSION); + + return 0; +} + +static int sb_build_dcd(struct sb_image_ctx *ictx, struct sb_cmd_list *cmd) +{ + struct sb_dcd_ctx *dctx; + + char *tok; + uint32_t id; + int ret; + + dctx = calloc(1, sizeof(*dctx)); + if (!dctx) + return -ENOMEM; + + ret = sb_grow_dcd(dctx, 4); + if (ret) + goto err_dcd; + + /* Read DCD block number. */ + tok = strtok(cmd->cmd, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: DCD block without number!\n", + cmd->lineno); + ret = -EINVAL; + goto err_dcd; + } + + /* Parse the DCD block number. */ + ret = sb_token_to_long(tok, &id); + if (ret) { + fprintf(stderr, "#%i ERR: Malformed DCD block number!\n", + cmd->lineno); + goto err_dcd; + } + + dctx->id = id; + + /* + * The DCD block is now constructed. Append it to the list. + * WARNING: The DCD size is still not computed and will be + * updated while parsing it's commands. + */ + if (!ictx->dcd_head) { + ictx->dcd_head = dctx; + ictx->dcd_tail = dctx; + } else { + ictx->dcd_tail->dcd = dctx; + ictx->dcd_tail = dctx; + } + + return 0; + +err_dcd: + free(dctx->payload); + free(dctx); + return ret; +} + +static int sb_build_dcd_block(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd, + uint32_t type) +{ + char *tok; + uint32_t address, value, length; + int ret; + + struct sb_dcd_ctx *dctx = ictx->dcd_tail; + uint32_t *dcd; + + if (dctx->prev_dcd_head && (type != SB_DCD_NOOP) && + ((dctx->prev_dcd_head[0] & 0xff0000ff) == type)) { + /* Same instruction as before, just append it. */ + ret = sb_grow_dcd(dctx, 8); + if (ret) + return ret; + } else if (type == SB_DCD_NOOP) { + ret = sb_grow_dcd(dctx, 4); + if (ret) + return ret; + + /* Update DCD command block pointer. */ + dctx->prev_dcd_head = dctx->payload + + dctx->size / sizeof(*dctx->payload) - 1; + + /* NOOP has only 4 bytes and no payload. */ + goto noop; + } else { + /* + * Either a different instruction block started now + * or this is the first instruction block. + */ + ret = sb_grow_dcd(dctx, 12); + if (ret) + return ret; + + /* Update DCD command block pointer. */ + dctx->prev_dcd_head = dctx->payload + + dctx->size / sizeof(*dctx->payload) - 3; + } + + dcd = dctx->payload + dctx->size / sizeof(*dctx->payload) - 2; + + /* + * Prepare the command. + */ + tok = strtok(cmd->cmd, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing DCD address!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + /* Read DCD destination address. */ + ret = sb_token_to_long(tok, &address); + if (ret) { + fprintf(stderr, "#%i ERR: Incorrect DCD address!\n", + cmd->lineno); + goto err; + } + + tok = strtok(NULL, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing DCD value!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + /* Read DCD operation value. */ + ret = sb_token_to_long(tok, &value); + if (ret) { + fprintf(stderr, "#%i ERR: Incorrect DCD value!\n", + cmd->lineno); + goto err; + } + + /* Fill in the new DCD entry. */ + dcd[0] = htonl(address); + dcd[1] = htonl(value); + +noop: + /* Update the DCD command block. */ + length = dctx->size - + ((dctx->prev_dcd_head - dctx->payload) * + sizeof(*dctx->payload)); + dctx->prev_dcd_head[0] = htonl(type | (length << 8)); + +err: + return ret; +} + +static int sb_build_section(struct sb_image_ctx *ictx, struct sb_cmd_list *cmd) +{ + struct sb_section_ctx *sctx; + struct sb_sections_header *shdr; + char *tok; + uint32_t bootable = 0; + uint32_t id; + int ret; + + sctx = calloc(1, sizeof(*sctx)); + if (!sctx) + return -ENOMEM; + + /* Read section number. */ + tok = strtok(cmd->cmd, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Section without number!\n", + cmd->lineno); + ret = -EINVAL; + goto err_sect; + } + + /* Parse the section number. */ + ret = sb_token_to_long(tok, &id); + if (ret) { + fprintf(stderr, "#%i ERR: Malformed section number!\n", + cmd->lineno); + goto err_sect; + } + + /* Read section's BOOTABLE flag. */ + tok = strtok(NULL, " "); + if (tok && (strlen(tok) == 8) && !strncmp(tok, "BOOTABLE", 8)) + bootable = SB_SECTION_FLAG_BOOTABLE; + + sctx->boot = bootable; + + shdr = &sctx->payload; + shdr->section_number = id; + shdr->section_flags = bootable; + + /* + * The section is now constructed. Append it to the list. + * WARNING: The section size is still not computed and will + * be updated while parsing it's commands. + */ + ictx->sect_count++; + + /* Mark that this section is bootable one. */ + if (bootable) { + if (ictx->sect_boot_found) { + fprintf(stderr, + "#%i WARN: Multiple bootable section!\n", + cmd->lineno); + } else { + ictx->sect_boot = id; + ictx->sect_boot_found = 1; + } + } + + if (!ictx->sect_head) { + ictx->sect_head = sctx; + ictx->sect_tail = sctx; + } else { + ictx->sect_tail->sect = sctx; + ictx->sect_tail = sctx; + } + + return 0; + +err_sect: + free(sctx); + return ret; +} + +static int sb_build_command_nop(struct sb_image_ctx *ictx) +{ + struct sb_section_ctx *sctx = ictx->sect_tail; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + + cctx = calloc(1, sizeof(*cctx)); + if (!cctx) + return -ENOMEM; + + ccmd = &cctx->payload; + + /* + * Construct the command. + */ + ccmd->header.checksum = 0x5a; + ccmd->header.tag = ROM_NOP_CMD; + + cctx->size = sizeof(*ccmd); + + /* + * Append the command to the last section. + */ + if (!sctx->cmd_head) { + sctx->cmd_head = cctx; + sctx->cmd_tail = cctx; + } else { + sctx->cmd_tail->cmd = cctx; + sctx->cmd_tail = cctx; + } + + return 0; +} + +static int sb_build_command_tag(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd) +{ + struct sb_section_ctx *sctx = ictx->sect_tail; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + char *tok; + + cctx = calloc(1, sizeof(*cctx)); + if (!cctx) + return -ENOMEM; + + ccmd = &cctx->payload; + + /* + * Prepare the command. + */ + /* Check for the LAST keyword. */ + tok = strtok(cmd->cmd, " "); + if (tok && !strcmp(tok, "LAST")) + ccmd->header.flags = ROM_TAG_CMD_FLAG_ROM_LAST_TAG; + + /* + * Construct the command. + */ + ccmd->header.checksum = 0x5a; + ccmd->header.tag = ROM_TAG_CMD; + + cctx->size = sizeof(*ccmd); + + /* + * Append the command to the last section. + */ + if (!sctx->cmd_head) { + sctx->cmd_head = cctx; + sctx->cmd_tail = cctx; + } else { + sctx->cmd_tail->cmd = cctx; + sctx->cmd_tail = cctx; + } + + return 0; +} + +static int sb_build_command_load(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd) +{ + struct sb_section_ctx *sctx = ictx->sect_tail; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + char *tok; + int ret, is_ivt = 0, is_dcd = 0; + uint32_t dest, dcd = 0; + + cctx = calloc(1, sizeof(*cctx)); + if (!cctx) + return -ENOMEM; + + ccmd = &cctx->payload; + + /* + * Prepare the command. + */ + tok = strtok(cmd->cmd, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing LOAD address or 'IVT'!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + /* Check for "IVT" flag. */ + if (!strcmp(tok, "IVT")) + is_ivt = 1; + if (!strcmp(tok, "DCD")) + is_dcd = 1; + if (is_ivt || is_dcd) { + tok = strtok(NULL, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing LOAD address!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + } + + /* Read load destination address. */ + ret = sb_token_to_long(tok, &dest); + if (ret) { + fprintf(stderr, "#%i ERR: Incorrect LOAD address!\n", + cmd->lineno); + goto err; + } + + /* Read filename or IVT entrypoint or DCD block ID. */ + tok = strtok(NULL, " "); + if (!tok) { + fprintf(stderr, + "#%i ERR: Missing LOAD filename or IVT ep or DCD block ID!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + if (is_ivt) { + /* Handle IVT. */ + struct sb_ivt_header *ivt; + uint32_t ivtep; + ret = sb_token_to_long(tok, &ivtep); + + if (ret) { + fprintf(stderr, + "#%i ERR: Incorrect IVT entry point!\n", + cmd->lineno); + goto err; + } + + ivt = calloc(1, sizeof(*ivt)); + if (!ivt) { + ret = -ENOMEM; + goto err; + } + + ivt->header = sb_hab_ivt_header(); + ivt->entry = ivtep; + ivt->self = dest; + + cctx->data = (uint8_t *)ivt; + cctx->length = sizeof(*ivt); + } else if (is_dcd) { + struct sb_dcd_ctx *dctx = ictx->dcd_head; + uint32_t dcdid; + uint8_t *payload; + uint32_t asize; + ret = sb_token_to_long(tok, &dcdid); + + if (ret) { + fprintf(stderr, + "#%i ERR: Incorrect DCD block ID!\n", + cmd->lineno); + goto err; + } + + while (dctx) { + if (dctx->id == dcdid) + break; + dctx = dctx->dcd; + } + + if (!dctx) { + fprintf(stderr, "#%i ERR: DCD block %08x not found!\n", + cmd->lineno, dcdid); + goto err; + } + + asize = roundup(dctx->size, SB_BLOCK_SIZE); + payload = calloc(1, asize); + if (!payload) { + ret = -ENOMEM; + goto err; + } + + memcpy(payload, dctx->payload, dctx->size); + + cctx->data = payload; + cctx->length = asize; + + /* Set the Load DCD flag. */ + dcd = ROM_LOAD_CMD_FLAG_DCD_LOAD; + } else { + /* Regular LOAD of a file. */ + ret = sb_load_file(cctx, tok); + if (ret) { + fprintf(stderr, "#%i ERR: Cannot load '%s'!\n", + cmd->lineno, tok); + goto err; + } + } + + if (cctx->length & (SB_BLOCK_SIZE - 1)) { + fprintf(stderr, "#%i ERR: Unaligned payload!\n", + cmd->lineno); + } + + /* + * Construct the command. + */ + ccmd->header.checksum = 0x5a; + ccmd->header.tag = ROM_LOAD_CMD; + ccmd->header.flags = dcd; + + ccmd->load.address = dest; + ccmd->load.count = cctx->length; + ccmd->load.crc32 = crc32(cctx->data, cctx->length); + + cctx->size = sizeof(*ccmd) + cctx->length; + + /* + * Append the command to the last section. + */ + if (!sctx->cmd_head) { + sctx->cmd_head = cctx; + sctx->cmd_tail = cctx; + } else { + sctx->cmd_tail->cmd = cctx; + sctx->cmd_tail = cctx; + } + + return 0; + +err: + free(cctx); + return ret; +} + +static int sb_build_command_fill(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd) +{ + struct sb_section_ctx *sctx = ictx->sect_tail; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + char *tok; + uint32_t address, pattern, length; + int ret; + + cctx = calloc(1, sizeof(*cctx)); + if (!cctx) + return -ENOMEM; + + ccmd = &cctx->payload; + + /* + * Prepare the command. + */ + tok = strtok(cmd->cmd, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing FILL address!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + /* Read fill destination address. */ + ret = sb_token_to_long(tok, &address); + if (ret) { + fprintf(stderr, "#%i ERR: Incorrect FILL address!\n", + cmd->lineno); + goto err; + } + + tok = strtok(NULL, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing FILL pattern!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + /* Read fill pattern address. */ + ret = sb_token_to_long(tok, &pattern); + if (ret) { + fprintf(stderr, "#%i ERR: Incorrect FILL pattern!\n", + cmd->lineno); + goto err; + } + + tok = strtok(NULL, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing FILL length!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + /* Read fill pattern address. */ + ret = sb_token_to_long(tok, &length); + if (ret) { + fprintf(stderr, "#%i ERR: Incorrect FILL length!\n", + cmd->lineno); + goto err; + } + + /* + * Construct the command. + */ + ccmd->header.checksum = 0x5a; + ccmd->header.tag = ROM_FILL_CMD; + + ccmd->fill.address = address; + ccmd->fill.count = length; + ccmd->fill.pattern = pattern; + + cctx->size = sizeof(*ccmd); + + /* + * Append the command to the last section. + */ + if (!sctx->cmd_head) { + sctx->cmd_head = cctx; + sctx->cmd_tail = cctx; + } else { + sctx->cmd_tail->cmd = cctx; + sctx->cmd_tail = cctx; + } + + return 0; + +err: + free(cctx); + return ret; +} + +static int sb_build_command_jump_call(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd, + unsigned int is_call) +{ + struct sb_section_ctx *sctx = ictx->sect_tail; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + char *tok; + uint32_t dest, arg = 0x0; + uint32_t hab = 0; + int ret; + const char *cmdname = is_call ? "CALL" : "JUMP"; + + cctx = calloc(1, sizeof(*cctx)); + if (!cctx) + return -ENOMEM; + + ccmd = &cctx->payload; + + /* + * Prepare the command. + */ + tok = strtok(cmd->cmd, " "); + if (!tok) { + fprintf(stderr, + "#%i ERR: Missing %s address or 'HAB'!\n", + cmd->lineno, cmdname); + ret = -EINVAL; + goto err; + } + + /* Check for "HAB" flag. */ + if (!strcmp(tok, "HAB")) { + hab = is_call ? ROM_CALL_CMD_FLAG_HAB : ROM_JUMP_CMD_FLAG_HAB; + tok = strtok(NULL, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing %s address!\n", + cmd->lineno, cmdname); + ret = -EINVAL; + goto err; + } + } + /* Read load destination address. */ + ret = sb_token_to_long(tok, &dest); + if (ret) { + fprintf(stderr, "#%i ERR: Incorrect %s address!\n", + cmd->lineno, cmdname); + goto err; + } + + tok = strtok(NULL, " "); + if (tok) { + ret = sb_token_to_long(tok, &arg); + if (ret) { + fprintf(stderr, + "#%i ERR: Incorrect %s argument!\n", + cmd->lineno, cmdname); + goto err; + } + } + + /* + * Construct the command. + */ + ccmd->header.checksum = 0x5a; + ccmd->header.tag = is_call ? ROM_CALL_CMD : ROM_JUMP_CMD; + ccmd->header.flags = hab; + + ccmd->call.address = dest; + ccmd->call.argument = arg; + + cctx->size = sizeof(*ccmd); + + /* + * Append the command to the last section. + */ + if (!sctx->cmd_head) { + sctx->cmd_head = cctx; + sctx->cmd_tail = cctx; + } else { + sctx->cmd_tail->cmd = cctx; + sctx->cmd_tail = cctx; + } + + return 0; + +err: + free(cctx); + return ret; +} + +static int sb_build_command_jump(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd) +{ + return sb_build_command_jump_call(ictx, cmd, 0); +} + +static int sb_build_command_call(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd) +{ + return sb_build_command_jump_call(ictx, cmd, 1); +} + +static int sb_build_command_mode(struct sb_image_ctx *ictx, + struct sb_cmd_list *cmd) +{ + struct sb_section_ctx *sctx = ictx->sect_tail; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + char *tok; + int ret; + unsigned int i; + uint32_t mode = 0xffffffff; + + cctx = calloc(1, sizeof(*cctx)); + if (!cctx) + return -ENOMEM; + + ccmd = &cctx->payload; + + /* + * Prepare the command. + */ + tok = strtok(cmd->cmd, " "); + if (!tok) { + fprintf(stderr, "#%i ERR: Missing MODE boot mode argument!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + for (i = 0; i < ARRAY_SIZE(modetable); i++) { + if (!strcmp(tok, modetable[i].name)) { + mode = modetable[i].mode; + break; + } + + if (!modetable[i].altname) + continue; + + if (!strcmp(tok, modetable[i].altname)) { + mode = modetable[i].mode; + break; + } + } + + if (mode == 0xffffffff) { + fprintf(stderr, "#%i ERR: Invalid MODE boot mode argument!\n", + cmd->lineno); + ret = -EINVAL; + goto err; + } + + /* + * Construct the command. + */ + ccmd->header.checksum = 0x5a; + ccmd->header.tag = ROM_MODE_CMD; + + ccmd->mode.mode = mode; + + cctx->size = sizeof(*ccmd); + + /* + * Append the command to the last section. + */ + if (!sctx->cmd_head) { + sctx->cmd_head = cctx; + sctx->cmd_tail = cctx; + } else { + sctx->cmd_tail->cmd = cctx; + sctx->cmd_tail = cctx; + } + + return 0; + +err: + free(cctx); + return ret; +} + +static int sb_prefill_image_header(struct sb_image_ctx *ictx) +{ + struct sb_boot_image_header *hdr = &ictx->payload; + + /* Fill signatures */ + memcpy(hdr->signature1, "STMP", 4); + memcpy(hdr->signature2, "sgtl", 4); + + /* SB Image version 1.1 */ + hdr->major_version = SB_VERSION_MAJOR; + hdr->minor_version = SB_VERSION_MINOR; + + /* Boot image major version */ + hdr->product_version.major = htons(0x999); + hdr->product_version.minor = htons(0x999); + hdr->product_version.revision = htons(0x999); + /* Boot image major version */ + hdr->component_version.major = htons(0x999); + hdr->component_version.minor = htons(0x999); + hdr->component_version.revision = htons(0x999); + + /* Drive tag must be 0x0 for i.MX23 */ + hdr->drive_tag = 0; + + hdr->header_blocks = + sizeof(struct sb_boot_image_header) / SB_BLOCK_SIZE; + hdr->section_header_size = + sizeof(struct sb_sections_header) / SB_BLOCK_SIZE; + hdr->timestamp_us = sb_get_timestamp() * 1000000; + + /* FIXME -- add proper config option */ + hdr->flags = ictx->verbose_boot ? SB_IMAGE_FLAG_VERBOSE : 0, + + /* FIXME -- We support only default key */ + hdr->key_count = 1; + + return 0; +} + +static int sb_postfill_image_header(struct sb_image_ctx *ictx) +{ + struct sb_boot_image_header *hdr = &ictx->payload; + struct sb_section_ctx *sctx = ictx->sect_head; + uint32_t kd_size, sections_blocks; + EVP_MD_CTX md_ctx; + + /* The main SB header size in blocks. */ + hdr->image_blocks = hdr->header_blocks; + + /* Size of the key dictionary, which has single zero entry. */ + kd_size = hdr->key_count * sizeof(struct sb_key_dictionary_key); + hdr->image_blocks += kd_size / SB_BLOCK_SIZE; + + /* Now count the payloads. */ + hdr->section_count = ictx->sect_count; + while (sctx) { + hdr->image_blocks += sctx->size / SB_BLOCK_SIZE; + sctx = sctx->sect; + } + + if (!ictx->sect_boot_found) { + fprintf(stderr, "ERR: No bootable section selected!\n"); + return -EINVAL; + } + hdr->first_boot_section_id = ictx->sect_boot; + + /* The n * SB section size in blocks. */ + sections_blocks = hdr->section_count * hdr->section_header_size; + hdr->image_blocks += sections_blocks; + + /* Key dictionary offset. */ + hdr->key_dictionary_block = hdr->header_blocks + sections_blocks; + + /* Digest of the whole image. */ + hdr->image_blocks += 2; + + /* Pointer past the dictionary. */ + hdr->first_boot_tag_block = + hdr->key_dictionary_block + kd_size / SB_BLOCK_SIZE; + + /* Compute header digest. */ + EVP_MD_CTX_init(&md_ctx); + + EVP_DigestInit(&md_ctx, EVP_sha1()); + EVP_DigestUpdate(&md_ctx, hdr->signature1, + sizeof(struct sb_boot_image_header) - + sizeof(hdr->digest)); + EVP_DigestFinal(&md_ctx, hdr->digest, NULL); + + return 0; +} + +static int sb_fixup_sections_and_tags(struct sb_image_ctx *ictx) +{ + /* Fixup the placement of sections. */ + struct sb_boot_image_header *ihdr = &ictx->payload; + struct sb_section_ctx *sctx = ictx->sect_head; + struct sb_sections_header *shdr; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + uint32_t offset = ihdr->first_boot_tag_block; + + while (sctx) { + shdr = &sctx->payload; + + /* Fill in the section TAG offset. */ + shdr->section_offset = offset + 1; + offset += shdr->section_size; + + /* Section length is measured from the TAG block. */ + shdr->section_size--; + + /* Fixup the TAG command. */ + cctx = sctx->cmd_head; + while (cctx) { + ccmd = &cctx->payload; + if (ccmd->header.tag == ROM_TAG_CMD) { + ccmd->tag.section_number = shdr->section_number; + ccmd->tag.section_length = shdr->section_size; + ccmd->tag.section_flags = shdr->section_flags; + } + + /* Update the command checksum. */ + ccmd->header.checksum = sb_command_checksum(ccmd); + + cctx = cctx->cmd; + } + + sctx = sctx->sect; + } + + return 0; +} + +static int sb_parse_line(struct sb_image_ctx *ictx, struct sb_cmd_list *cmd) +{ + char *tok; + char *line = cmd->cmd; + char *rptr; + int ret; + + /* Analyze the identifier on this line first. */ + tok = strtok_r(line, " ", &rptr); + if (!tok || (strlen(tok) == 0)) { + fprintf(stderr, "#%i ERR: Invalid line!\n", cmd->lineno); + return -EINVAL; + } + + cmd->cmd = rptr; + + /* DCD */ + if (!strcmp(tok, "DCD")) { + ictx->in_section = 0; + ictx->in_dcd = 1; + sb_build_dcd(ictx, cmd); + return 0; + } + + /* Section */ + if (!strcmp(tok, "SECTION")) { + ictx->in_section = 1; + ictx->in_dcd = 0; + sb_build_section(ictx, cmd); + return 0; + } + + if (!ictx->in_section && !ictx->in_dcd) { + fprintf(stderr, "#%i ERR: Data outside of a section!\n", + cmd->lineno); + return -EINVAL; + } + + if (ictx->in_section) { + /* Section commands */ + if (!strcmp(tok, "NOP")) { + ret = sb_build_command_nop(ictx); + } else if (!strcmp(tok, "TAG")) { + ret = sb_build_command_tag(ictx, cmd); + } else if (!strcmp(tok, "LOAD")) { + ret = sb_build_command_load(ictx, cmd); + } else if (!strcmp(tok, "FILL")) { + ret = sb_build_command_fill(ictx, cmd); + } else if (!strcmp(tok, "JUMP")) { + ret = sb_build_command_jump(ictx, cmd); + } else if (!strcmp(tok, "CALL")) { + ret = sb_build_command_call(ictx, cmd); + } else if (!strcmp(tok, "MODE")) { + ret = sb_build_command_mode(ictx, cmd); + } else { + fprintf(stderr, + "#%i ERR: Unsupported instruction '%s'!\n", + cmd->lineno, tok); + return -ENOTSUP; + } + } else if (ictx->in_dcd) { + char *lptr; + uint32_t ilen = '1'; + + tok = strtok_r(tok, ".", &lptr); + if (!tok || (strlen(tok) == 0) || (lptr && strlen(lptr) != 1)) { + fprintf(stderr, "#%i ERR: Invalid line!\n", + cmd->lineno); + return -EINVAL; + } + + if (lptr && + (lptr[0] != '1' && lptr[0] != '2' && lptr[0] != '4')) { + fprintf(stderr, "#%i ERR: Invalid instruction width!\n", + cmd->lineno); + return -EINVAL; + } + + if (lptr) + ilen = lptr[0] - '1'; + + /* DCD commands */ + if (!strcmp(tok, "WRITE")) { + ret = sb_build_dcd_block(ictx, cmd, + SB_DCD_WRITE | ilen); + } else if (!strcmp(tok, "ANDC")) { + ret = sb_build_dcd_block(ictx, cmd, + SB_DCD_ANDC | ilen); + } else if (!strcmp(tok, "ORR")) { + ret = sb_build_dcd_block(ictx, cmd, + SB_DCD_ORR | ilen); + } else if (!strcmp(tok, "EQZ")) { + ret = sb_build_dcd_block(ictx, cmd, + SB_DCD_CHK_EQZ | ilen); + } else if (!strcmp(tok, "EQ")) { + ret = sb_build_dcd_block(ictx, cmd, + SB_DCD_CHK_EQ | ilen); + } else if (!strcmp(tok, "NEQ")) { + ret = sb_build_dcd_block(ictx, cmd, + SB_DCD_CHK_NEQ | ilen); + } else if (!strcmp(tok, "NEZ")) { + ret = sb_build_dcd_block(ictx, cmd, + SB_DCD_CHK_NEZ | ilen); + } else if (!strcmp(tok, "NOOP")) { + ret = sb_build_dcd_block(ictx, cmd, SB_DCD_NOOP); + } else { + fprintf(stderr, + "#%i ERR: Unsupported instruction '%s'!\n", + cmd->lineno, tok); + return -ENOTSUP; + } + } else { + fprintf(stderr, "#%i ERR: Unsupported instruction '%s'!\n", + cmd->lineno, tok); + return -ENOTSUP; + } + + /* + * Here we have at least one section with one command, otherwise we + * would have failed already higher above. + * + * FIXME -- should the updating happen here ? + */ + if (ictx->in_section && !ret) { + ictx->sect_tail->size += ictx->sect_tail->cmd_tail->size; + ictx->sect_tail->payload.section_size = + ictx->sect_tail->size / SB_BLOCK_SIZE; + } + + return ret; +} + +static int sb_load_cmdfile(struct sb_image_ctx *ictx) +{ + struct sb_cmd_list cmd; + int lineno = 1; + FILE *fp; + char *line = NULL; + ssize_t rlen; + size_t len; + + fp = fopen(ictx->cfg_filename, "r"); + if (!fp) + goto err_file; + + while ((rlen = getline(&line, &len, fp)) > 0) { + memset(&cmd, 0, sizeof(cmd)); + + /* Strip the trailing newline. */ + line[rlen - 1] = '\0'; + + cmd.cmd = line; + cmd.len = rlen; + cmd.lineno = lineno++; + + sb_parse_line(ictx, &cmd); + } + + free(line); + + fclose(fp); + + return 0; + +err_file: + fclose(fp); + fprintf(stderr, "ERR: Failed to load file \"%s\"\n", + ictx->cfg_filename); + return -EINVAL; +} + +static int sb_build_tree_from_cfg(struct sb_image_ctx *ictx) +{ + int ret; + + ret = sb_load_cmdfile(ictx); + if (ret) + return ret; + + ret = sb_prefill_image_header(ictx); + if (ret) + return ret; + + ret = sb_postfill_image_header(ictx); + if (ret) + return ret; + + ret = sb_fixup_sections_and_tags(ictx); + if (ret) + return ret; + + return 0; +} + +static int sb_verify_image_header(struct sb_image_ctx *ictx, + FILE *fp, long fsize) +{ + /* Verify static fields in the image header. */ + struct sb_boot_image_header *hdr = &ictx->payload; + const char *stat[2] = { "[PASS]", "[FAIL]" }; + struct tm tm; + int sz, ret = 0; + unsigned char digest[20]; + EVP_MD_CTX md_ctx; + unsigned long size; + + /* Start image-wide crypto. */ + EVP_MD_CTX_init(&ictx->md_ctx); + EVP_DigestInit(&ictx->md_ctx, EVP_sha1()); + + soprintf(ictx, "---------- Verifying SB Image Header ----------\n"); + + size = fread(&ictx->payload, 1, sizeof(ictx->payload), fp); + if (size != sizeof(ictx->payload)) { + fprintf(stderr, "ERR: SB image header too short!\n"); + return -EINVAL; + } + + /* Compute header digest. */ + EVP_MD_CTX_init(&md_ctx); + EVP_DigestInit(&md_ctx, EVP_sha1()); + EVP_DigestUpdate(&md_ctx, hdr->signature1, + sizeof(struct sb_boot_image_header) - + sizeof(hdr->digest)); + EVP_DigestFinal(&md_ctx, digest, NULL); + + sb_aes_init(ictx, NULL, 1); + sb_encrypt_sb_header(ictx); + + if (memcmp(digest, hdr->digest, 20)) + ret = -EINVAL; + soprintf(ictx, "%s Image header checksum: %s\n", stat[!!ret], + ret ? "BAD" : "OK"); + if (ret) + return ret; + + if (memcmp(hdr->signature1, "STMP", 4) || + memcmp(hdr->signature2, "sgtl", 4)) + ret = -EINVAL; + soprintf(ictx, "%s Signatures: '%.4s' '%.4s'\n", + stat[!!ret], hdr->signature1, hdr->signature2); + if (ret) + return ret; + + if ((hdr->major_version != SB_VERSION_MAJOR) || + ((hdr->minor_version != 1) && (hdr->minor_version != 2))) + ret = -EINVAL; + soprintf(ictx, "%s Image version: v%i.%i\n", stat[!!ret], + hdr->major_version, hdr->minor_version); + if (ret) + return ret; + + ret = sb_get_time(hdr->timestamp_us / 1000000, &tm); + soprintf(ictx, + "%s Creation time: %02i:%02i:%02i %02i/%02i/%04i\n", + stat[!!ret], tm.tm_hour, tm.tm_min, tm.tm_sec, + tm.tm_mday, tm.tm_mon, tm.tm_year + 2000); + if (ret) + return ret; + + soprintf(ictx, "%s Product version: %x.%x.%x\n", stat[0], + ntohs(hdr->product_version.major), + ntohs(hdr->product_version.minor), + ntohs(hdr->product_version.revision)); + soprintf(ictx, "%s Component version: %x.%x.%x\n", stat[0], + ntohs(hdr->component_version.major), + ntohs(hdr->component_version.minor), + ntohs(hdr->component_version.revision)); + + if (hdr->flags & ~SB_IMAGE_FLAG_VERBOSE) + ret = -EINVAL; + soprintf(ictx, "%s Image flags: %s\n", stat[!!ret], + hdr->flags & SB_IMAGE_FLAG_VERBOSE ? "Verbose_boot" : ""); + if (ret) + return ret; + + if (hdr->drive_tag != 0) + ret = -EINVAL; + soprintf(ictx, "%s Drive tag: %i\n", stat[!!ret], + hdr->drive_tag); + if (ret) + return ret; + + sz = sizeof(struct sb_boot_image_header) / SB_BLOCK_SIZE; + if (hdr->header_blocks != sz) + ret = -EINVAL; + soprintf(ictx, "%s Image header size (blocks): %i\n", stat[!!ret], + hdr->header_blocks); + if (ret) + return ret; + + sz = sizeof(struct sb_sections_header) / SB_BLOCK_SIZE; + if (hdr->section_header_size != sz) + ret = -EINVAL; + soprintf(ictx, "%s Section header size (blocks): %i\n", stat[!!ret], + hdr->section_header_size); + if (ret) + return ret; + + soprintf(ictx, "%s Sections count: %i\n", stat[!!ret], + hdr->section_count); + soprintf(ictx, "%s First bootable section %i\n", stat[!!ret], + hdr->first_boot_section_id); + + if (hdr->image_blocks != fsize / SB_BLOCK_SIZE) + ret = -EINVAL; + soprintf(ictx, "%s Image size (blocks): %i\n", stat[!!ret], + hdr->image_blocks); + if (ret) + return ret; + + sz = hdr->header_blocks + hdr->section_header_size * hdr->section_count; + if (hdr->key_dictionary_block != sz) + ret = -EINVAL; + soprintf(ictx, "%s Key dict offset (blocks): %i\n", stat[!!ret], + hdr->key_dictionary_block); + if (ret) + return ret; + + if (hdr->key_count != 1) + ret = -EINVAL; + soprintf(ictx, "%s Number of encryption keys: %i\n", stat[!!ret], + hdr->key_count); + if (ret) + return ret; + + sz = hdr->header_blocks + hdr->section_header_size * hdr->section_count; + sz += hdr->key_count * + sizeof(struct sb_key_dictionary_key) / SB_BLOCK_SIZE; + if (hdr->first_boot_tag_block != (unsigned)sz) + ret = -EINVAL; + soprintf(ictx, "%s First TAG block (blocks): %i\n", stat[!!ret], + hdr->first_boot_tag_block); + if (ret) + return ret; + + return 0; +} + +static void sb_decrypt_tag(struct sb_image_ctx *ictx, + struct sb_cmd_ctx *cctx) +{ + EVP_MD_CTX *md_ctx = &ictx->md_ctx; + struct sb_command *cmd = &cctx->payload; + + sb_aes_crypt(ictx, (uint8_t *)&cctx->c_payload, + (uint8_t *)&cctx->payload, sizeof(*cmd)); + EVP_DigestUpdate(md_ctx, &cctx->c_payload, sizeof(*cmd)); +} + +static int sb_verify_command(struct sb_image_ctx *ictx, + struct sb_cmd_ctx *cctx, FILE *fp, + unsigned long *tsize) +{ + struct sb_command *ccmd = &cctx->payload; + unsigned long size, asize; + char *csum, *flag = ""; + int ret; + unsigned int i; + uint8_t csn, csc = ccmd->header.checksum; + ccmd->header.checksum = 0x5a; + csn = sb_command_checksum(ccmd); + ccmd->header.checksum = csc; + + if (csc == csn) + ret = 0; + else + ret = -EINVAL; + csum = ret ? "checksum BAD" : "checksum OK"; + + switch (ccmd->header.tag) { + case ROM_NOP_CMD: + soprintf(ictx, " NOOP # %s\n", csum); + return ret; + case ROM_TAG_CMD: + if (ccmd->header.flags & ROM_TAG_CMD_FLAG_ROM_LAST_TAG) + flag = "LAST"; + soprintf(ictx, " TAG %s # %s\n", flag, csum); + sb_aes_reinit(ictx, 0); + return ret; + case ROM_LOAD_CMD: + soprintf(ictx, " LOAD addr=0x%08x length=0x%08x # %s\n", + ccmd->load.address, ccmd->load.count, csum); + + cctx->length = ccmd->load.count; + asize = roundup(cctx->length, SB_BLOCK_SIZE); + cctx->data = malloc(asize); + if (!cctx->data) + return -ENOMEM; + + size = fread(cctx->data, 1, asize, fp); + if (size != asize) { + fprintf(stderr, + "ERR: SB LOAD command payload too short!\n"); + return -EINVAL; + } + + *tsize += size; + + EVP_DigestUpdate(&ictx->md_ctx, cctx->data, asize); + sb_aes_crypt(ictx, cctx->data, cctx->data, asize); + + if (ccmd->load.crc32 != crc32(cctx->data, asize)) { + fprintf(stderr, + "ERR: SB LOAD command payload CRC32 invalid!\n"); + return -EINVAL; + } + return 0; + case ROM_FILL_CMD: + soprintf(ictx, + " FILL addr=0x%08x length=0x%08x pattern=0x%08x # %s\n", + ccmd->fill.address, ccmd->fill.count, + ccmd->fill.pattern, csum); + return 0; + case ROM_JUMP_CMD: + if (ccmd->header.flags & ROM_JUMP_CMD_FLAG_HAB) + flag = " HAB"; + soprintf(ictx, + " JUMP%s addr=0x%08x r0_arg=0x%08x # %s\n", + flag, ccmd->fill.address, ccmd->jump.argument, csum); + return 0; + case ROM_CALL_CMD: + if (ccmd->header.flags & ROM_CALL_CMD_FLAG_HAB) + flag = " HAB"; + soprintf(ictx, + " CALL%s addr=0x%08x r0_arg=0x%08x # %s\n", + flag, ccmd->fill.address, ccmd->jump.argument, csum); + return 0; + case ROM_MODE_CMD: + for (i = 0; i < ARRAY_SIZE(modetable); i++) { + if (ccmd->mode.mode == modetable[i].mode) { + soprintf(ictx, " MODE %s # %s\n", + modetable[i].name, csum); + break; + } + } + fprintf(stderr, " MODE !INVALID! # %s\n", csum); + return 0; + } + + return ret; +} + +static int sb_verify_commands(struct sb_image_ctx *ictx, + struct sb_section_ctx *sctx, FILE *fp) +{ + unsigned long size, tsize = 0; + struct sb_cmd_ctx *cctx; + int ret; + + sb_aes_reinit(ictx, 0); + + while (tsize < sctx->size) { + cctx = calloc(1, sizeof(*cctx)); + if (!cctx) + return -ENOMEM; + if (!sctx->cmd_head) { + sctx->cmd_head = cctx; + sctx->cmd_tail = cctx; + } else { + sctx->cmd_tail->cmd = cctx; + sctx->cmd_tail = cctx; + } + + size = fread(&cctx->c_payload, 1, sizeof(cctx->c_payload), fp); + if (size != sizeof(cctx->c_payload)) { + fprintf(stderr, "ERR: SB command header too short!\n"); + return -EINVAL; + } + + tsize += size; + + sb_decrypt_tag(ictx, cctx); + + ret = sb_verify_command(ictx, cctx, fp, &tsize); + if (ret) + return -EINVAL; + } + + return 0; +} + +static int sb_verify_sections_cmds(struct sb_image_ctx *ictx, FILE *fp) +{ + struct sb_boot_image_header *hdr = &ictx->payload; + struct sb_sections_header *shdr; + unsigned int i; + int ret; + struct sb_section_ctx *sctx; + unsigned long size; + char *bootable = ""; + + soprintf(ictx, "----- Verifying SB Sections and Commands -----\n"); + + for (i = 0; i < hdr->section_count; i++) { + sctx = calloc(1, sizeof(*sctx)); + if (!sctx) + return -ENOMEM; + if (!ictx->sect_head) { + ictx->sect_head = sctx; + ictx->sect_tail = sctx; + } else { + ictx->sect_tail->sect = sctx; + ictx->sect_tail = sctx; + } + + size = fread(&sctx->payload, 1, sizeof(sctx->payload), fp); + if (size != sizeof(sctx->payload)) { + fprintf(stderr, "ERR: SB section header too short!\n"); + return -EINVAL; + } + } + + size = fread(&ictx->sb_dict_key, 1, sizeof(ictx->sb_dict_key), fp); + if (size != sizeof(ictx->sb_dict_key)) { + fprintf(stderr, "ERR: SB key dictionary too short!\n"); + return -EINVAL; + } + + sb_encrypt_sb_sections_header(ictx); + sb_aes_reinit(ictx, 0); + sb_decrypt_key_dictionary_key(ictx); + + sb_aes_reinit(ictx, 0); + + sctx = ictx->sect_head; + while (sctx) { + shdr = &sctx->payload; + + if (shdr->section_flags & SB_SECTION_FLAG_BOOTABLE) { + sctx->boot = 1; + bootable = " BOOTABLE"; + } + + sctx->size = (shdr->section_size * SB_BLOCK_SIZE) + + sizeof(struct sb_command); + soprintf(ictx, "SECTION 0x%x%s # size = %i bytes\n", + shdr->section_number, bootable, sctx->size); + + if (shdr->section_flags & ~SB_SECTION_FLAG_BOOTABLE) + fprintf(stderr, " WARN: Unknown section flag(s) %08x\n", + shdr->section_flags); + + if ((shdr->section_flags & SB_SECTION_FLAG_BOOTABLE) && + (hdr->first_boot_section_id != shdr->section_number)) { + fprintf(stderr, + " WARN: Bootable section does ID not match image header ID!\n"); + } + + ret = sb_verify_commands(ictx, sctx, fp); + if (ret) + return ret; + + sctx = sctx->sect; + } + + /* + * FIXME IDEA: + * check if the first TAG command is at sctx->section_offset + */ + return 0; +} + +static int sb_verify_image_end(struct sb_image_ctx *ictx, + FILE *fp, off_t filesz) +{ + uint8_t digest[32]; + unsigned long size; + off_t pos; + int ret; + + soprintf(ictx, "------------- Verifying image end -------------\n"); + + size = fread(digest, 1, sizeof(digest), fp); + if (size != sizeof(digest)) { + fprintf(stderr, "ERR: SB key dictionary too short!\n"); + return -EINVAL; + } + + pos = ftell(fp); + if (pos != filesz) { + fprintf(stderr, "ERR: Trailing data past the image!\n"); + return -EINVAL; + } + + /* Check the image digest. */ + EVP_DigestFinal(&ictx->md_ctx, ictx->digest, NULL); + + /* Decrypt the image digest from the input image. */ + sb_aes_reinit(ictx, 0); + sb_aes_crypt(ictx, digest, digest, sizeof(digest)); + + /* Check all of 20 bytes of the SHA1 hash. */ + ret = memcmp(digest, ictx->digest, 20) ? -EINVAL : 0; + + if (ret) + soprintf(ictx, "[FAIL] Full-image checksum: BAD\n"); + else + soprintf(ictx, "[PASS] Full-image checksum: OK\n"); + + return ret; +} + + +static int sb_build_tree_from_img(struct sb_image_ctx *ictx) +{ + long filesize; + int ret; + FILE *fp; + + if (!ictx->input_filename) { + fprintf(stderr, "ERR: Missing filename!\n"); + return -EINVAL; + } + + fp = fopen(ictx->input_filename, "r"); + if (!fp) + goto err_open; + + ret = fseek(fp, 0, SEEK_END); + if (ret < 0) + goto err_file; + + filesize = ftell(fp); + if (filesize < 0) + goto err_file; + + ret = fseek(fp, 0, SEEK_SET); + if (ret < 0) + goto err_file; + + if (filesize < (signed)sizeof(ictx->payload)) { + fprintf(stderr, "ERR: File too short!\n"); + goto err_file; + } + + if (filesize & (SB_BLOCK_SIZE - 1)) { + fprintf(stderr, "ERR: The file is not aligned!\n"); + goto err_file; + } + + /* Load and verify image header */ + ret = sb_verify_image_header(ictx, fp, filesize); + if (ret) + goto err_verify; + + /* Load and verify sections and commands */ + ret = sb_verify_sections_cmds(ictx, fp); + if (ret) + goto err_verify; + + ret = sb_verify_image_end(ictx, fp, filesize); + if (ret) + goto err_verify; + + ret = 0; + +err_verify: + soprintf(ictx, "-------------------- Result -------------------\n"); + soprintf(ictx, "Verification %s\n", ret ? "FAILED" : "PASSED"); + + /* Stop the encryption session. */ + sb_aes_deinit(&ictx->cipher_ctx); + + fclose(fp); + return ret; + +err_file: + fclose(fp); +err_open: + fprintf(stderr, "ERR: Failed to load file \"%s\"\n", + ictx->input_filename); + return -EINVAL; +} + +static void sb_free_image(struct sb_image_ctx *ictx) +{ + struct sb_section_ctx *sctx = ictx->sect_head, *s_head; + struct sb_dcd_ctx *dctx = ictx->dcd_head, *d_head; + struct sb_cmd_ctx *cctx, *c_head; + + while (sctx) { + s_head = sctx; + c_head = sctx->cmd_head; + + while (c_head) { + cctx = c_head; + c_head = c_head->cmd; + if (cctx->data) + free(cctx->data); + free(cctx); + } + + sctx = sctx->sect; + free(s_head); + } + + while (dctx) { + d_head = dctx; + dctx = dctx->dcd; + free(d_head->payload); + free(d_head); + } +} + +/* + * MXSSB-MKIMAGE glue code. + */ +static int mxsimage_check_image_types(uint8_t type) +{ + if (type == IH_TYPE_MXSIMAGE) + return EXIT_SUCCESS; + else + return EXIT_FAILURE; +} + +static void mxsimage_set_header(void *ptr, struct stat *sbuf, int ifd, + struct mkimage_params *params) +{ +} + +int mxsimage_check_params(struct mkimage_params *params) +{ + if (!params) + return -1; + if (!strlen(params->imagename)) { + fprintf(stderr, + "Error: %s - Configuration file not specified, it is needed for mxsimage generation\n", + params->cmdname); + return -1; + } + + /* + * Check parameters: + * XIP is not allowed and verify that incompatible + * parameters are not sent at the same time + * For example, if list is required a data image must not be provided + */ + return (params->dflag && (params->fflag || params->lflag)) || + (params->fflag && (params->dflag || params->lflag)) || + (params->lflag && (params->dflag || params->fflag)) || + (params->xflag) || !(strlen(params->imagename)); +} + +static int mxsimage_verify_print_header(char *file, int silent) +{ + int ret; + struct sb_image_ctx ctx; + + memset(&ctx, 0, sizeof(ctx)); + + ctx.input_filename = file; + ctx.silent_dump = silent; + + ret = sb_build_tree_from_img(&ctx); + sb_free_image(&ctx); + + return ret; +} + +char *imagefile; +static int mxsimage_verify_header(unsigned char *ptr, int image_size, + struct mkimage_params *params) +{ + struct sb_boot_image_header *hdr; + + if (!ptr) + return -EINVAL; + + hdr = (struct sb_boot_image_header *)ptr; + + /* + * Check if the header contains the MXS image signatures, + * if so, do a full-image verification. + */ + if (memcmp(hdr->signature1, "STMP", 4) || + memcmp(hdr->signature2, "sgtl", 4)) + return -EINVAL; + + imagefile = params->imagefile; + + return mxsimage_verify_print_header(params->imagefile, 1); +} + +static void mxsimage_print_header(const void *hdr) +{ + if (imagefile) + mxsimage_verify_print_header(imagefile, 0); +} + +static int sb_build_image(struct sb_image_ctx *ictx, + struct image_type_params *tparams) +{ + struct sb_boot_image_header *sb_header = &ictx->payload; + struct sb_section_ctx *sctx; + struct sb_cmd_ctx *cctx; + struct sb_command *ccmd; + struct sb_key_dictionary_key *sb_dict_key = &ictx->sb_dict_key; + + uint8_t *image, *iptr; + + /* Calculate image size. */ + uint32_t size = sizeof(*sb_header) + + ictx->sect_count * sizeof(struct sb_sections_header) + + sizeof(*sb_dict_key) + sizeof(ictx->digest); + + sctx = ictx->sect_head; + while (sctx) { + size += sctx->size; + sctx = sctx->sect; + }; + + image = malloc(size); + if (!image) + return -ENOMEM; + iptr = image; + + memcpy(iptr, sb_header, sizeof(*sb_header)); + iptr += sizeof(*sb_header); + + sctx = ictx->sect_head; + while (sctx) { + memcpy(iptr, &sctx->payload, sizeof(struct sb_sections_header)); + iptr += sizeof(struct sb_sections_header); + sctx = sctx->sect; + }; + + memcpy(iptr, sb_dict_key, sizeof(*sb_dict_key)); + iptr += sizeof(*sb_dict_key); + + sctx = ictx->sect_head; + while (sctx) { + cctx = sctx->cmd_head; + while (cctx) { + ccmd = &cctx->payload; + + memcpy(iptr, &cctx->c_payload, sizeof(cctx->payload)); + iptr += sizeof(cctx->payload); + + if (ccmd->header.tag == ROM_LOAD_CMD) { + memcpy(iptr, cctx->data, cctx->length); + iptr += cctx->length; + } + + cctx = cctx->cmd; + } + + sctx = sctx->sect; + }; + + memcpy(iptr, ictx->digest, sizeof(ictx->digest)); + iptr += sizeof(ictx->digest); + + /* Configure the mkimage */ + tparams->hdr = image; + tparams->header_size = size; + + return 0; +} + +static int mxsimage_generate(struct mkimage_params *params, + struct image_type_params *tparams) +{ + int ret; + struct sb_image_ctx ctx; + + /* Do not copy the U-Boot image! */ + params->skipcpy = 1; + + memset(&ctx, 0, sizeof(ctx)); + + ctx.cfg_filename = params->imagename; + ctx.output_filename = params->imagefile; + ctx.verbose_boot = 1; + + ret = sb_build_tree_from_cfg(&ctx); + if (ret) + goto fail; + + ret = sb_encrypt_image(&ctx); + if (!ret) + ret = sb_build_image(&ctx, tparams); + +fail: + sb_free_image(&ctx); + + return ret; +} + +/* + * mxsimage parameters + */ +static struct image_type_params mxsimage_params = { + .name = "Freescale MXS Boot Image support", + .header_size = 0, + .hdr = NULL, + .check_image_type = mxsimage_check_image_types, + .verify_header = mxsimage_verify_header, + .print_header = mxsimage_print_header, + .set_header = mxsimage_set_header, + .check_params = mxsimage_check_params, + .vrec_header = mxsimage_generate, +}; + +void init_mxs_image_type(void) +{ + mkimage_register(&mxsimage_params); +} + +#else +void init_mxs_image_type(void) +{ +} +#endif diff --git a/tools/mxsimage.h b/tools/mxsimage.h new file mode 100644 index 0000000..6cd59d2 --- /dev/null +++ b/tools/mxsimage.h @@ -0,0 +1,230 @@ +/* + * Freescale i.MX28 SB image generator + * + * Copyright (C) 2012 Marek Vasut + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __MXSSB_H__ +#define __MXSSB_H__ + +#include +#include + +#define SB_BLOCK_SIZE 16 + +#define roundup(x, y) ((((x) + ((y) - 1)) / (y)) * (y)) +#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0])) + +struct sb_boot_image_version { + uint16_t major; + uint16_t pad0; + uint16_t minor; + uint16_t pad1; + uint16_t revision; + uint16_t pad2; +}; + +struct sb_boot_image_header { + union { + /* SHA1 of the header. */ + uint8_t digest[20]; + struct { + /* CBC-MAC initialization vector. */ + uint8_t iv[16]; + uint8_t extra[4]; + }; + }; + /* 'STMP' */ + uint8_t signature1[4]; + /* Major version of the image format. */ + uint8_t major_version; + /* Minor version of the image format. */ + uint8_t minor_version; + /* Flags associated with the image. */ + uint16_t flags; + /* Size of the image in 16b blocks. */ + uint32_t image_blocks; + /* Offset of the first tag in 16b blocks. */ + uint32_t first_boot_tag_block; + /* ID of the section to boot from. */ + uint32_t first_boot_section_id; + /* Amount of crypto keys. */ + uint16_t key_count; + /* Offset to the key dictionary in 16b blocks. */ + uint16_t key_dictionary_block; + /* Size of this header in 16b blocks. */ + uint16_t header_blocks; + /* Amount of section headers. */ + uint16_t section_count; + /* Section header size in 16b blocks. */ + uint16_t section_header_size; + /* Padding to align timestamp to uint64_t. */ + uint8_t padding0[2]; + /* 'sgtl' (since v1.1) */ + uint8_t signature2[4]; + /* Image generation date, in microseconds since 1.1.2000 . */ + uint64_t timestamp_us; + /* Product version. */ + struct sb_boot_image_version + product_version; + /* Component version. */ + struct sb_boot_image_version + component_version; + /* Drive tag for the system drive. (since v1.1) */ + uint16_t drive_tag; + /* Padding. */ + uint8_t padding1[6]; +}; + +#define SB_VERSION_MAJOR 1 +#define SB_VERSION_MINOR 1 + +/* Enable to HTLLC verbose boot report. */ +#define SB_IMAGE_FLAG_VERBOSE (1 << 0) + +struct sb_key_dictionary_key { + /* The CBC-MAC of image and sections header. */ + uint8_t cbc_mac[SB_BLOCK_SIZE]; + /* The AES key encrypted by image key (zero). */ + uint8_t key[SB_BLOCK_SIZE]; +}; + +struct sb_ivt_header { + uint32_t header; + uint32_t entry; + uint32_t reserved1; + uint32_t dcd; + uint32_t boot_data; + uint32_t self; + uint32_t csf; + uint32_t reserved2; +}; + +#define SB_HAB_IVT_TAG 0xd1UL +#define SB_HAB_DCD_TAG 0xd2UL + +#define SB_HAB_VERSION 0x40UL + +/* + * The "size" field in the IVT header is not naturally aligned, + * use this macro to fill first 4 bytes of the IVT header without + * causing issues on some systems (esp. M68k, PPC, MIPS-BE, ARM-BE). + */ +static inline uint32_t sb_hab_ivt_header(void) +{ + uint32_t ret = 0; + ret |= SB_HAB_IVT_TAG << 24; + ret |= sizeof(struct sb_ivt_header) << 16; + ret |= SB_HAB_VERSION; + return htonl(ret); +} + +struct sb_sections_header { + /* Section number. */ + uint32_t section_number; + /* Offset of this sections first instruction after "TAG". */ + uint32_t section_offset; + /* Size of the section in 16b blocks. */ + uint32_t section_size; + /* Section flags. */ + uint32_t section_flags; +}; + +#define SB_SECTION_FLAG_BOOTABLE (1 << 0) + +struct sb_command { + struct { + uint8_t checksum; + uint8_t tag; + uint16_t flags; +#define ROM_TAG_CMD_FLAG_ROM_LAST_TAG 0x1 +#define ROM_LOAD_CMD_FLAG_DCD_LOAD 0x1 /* MX28 only */ +#define ROM_JUMP_CMD_FLAG_HAB 0x1 /* MX28 only */ +#define ROM_CALL_CMD_FLAG_HAB 0x1 /* MX28 only */ + } header; + + union { + struct { + uint32_t reserved[3]; + } nop; + struct { + uint32_t section_number; + uint32_t section_length; + uint32_t section_flags; + } tag; + struct { + uint32_t address; + uint32_t count; + uint32_t crc32; + } load; + struct { + uint32_t address; + uint32_t count; + uint32_t pattern; + } fill; + struct { + uint32_t address; + uint32_t reserved; + /* Passed in register r0 before JUMP */ + uint32_t argument; + } jump; + struct { + uint32_t address; + uint32_t reserved; + /* Passed in register r0 before CALL */ + uint32_t argument; + } call; + struct { + uint32_t reserved1; + uint32_t reserved2; + uint32_t mode; + } mode; + + }; +}; + +/* + * Most of the mode names are same or at least similar + * on i.MX23 and i.MX28, but some of the mode names + * differ. The "name" field represents the mode name + * on i.MX28 as seen in Table 12-2 of the datasheet. + * The "altname" field represents the differently named + * fields on i.MX23 as seen in Table 35-3 of the + * datasheet. + */ +static const struct { + const char *name; + const char *altname; + const uint8_t mode; +} modetable[] = { + { "USB", NULL, 0x00 }, + { "I2C", NULL, 0x01 }, + { "SPI2_FLASH", "SPI1_FLASH", 0x02 }, + { "SPI3_FLASH", "SPI2_FLASH", 0x03 }, + { "NAND_BCH", NULL, 0x04 }, + { "JTAG", NULL, 0x06 }, + { "SPI3_EEPROM", "SPI2_EEPROM", 0x08 }, + { "SD_SSP0", NULL, 0x09 }, + { "SD_SSP1", NULL, 0x0A } +}; + +enum sb_tag { + ROM_NOP_CMD = 0x00, + ROM_TAG_CMD = 0x01, + ROM_LOAD_CMD = 0x02, + ROM_FILL_CMD = 0x03, + ROM_JUMP_CMD = 0x04, + ROM_CALL_CMD = 0x05, + ROM_MODE_CMD = 0x06 +}; + +struct sb_source_entry { + uint8_t tag; + uint32_t address; + uint32_t flags; + char *filename; +}; + +#endif /* __MXSSB_H__ */ -- cgit v0.10.2 From a5f746f3a27dd19b2180dfa79ca929c80ea80784 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Mon, 26 Aug 2013 20:43:34 +0200 Subject: tools: Sort lists of files in Makefile Fix the lists of files so they are in order again. Signed-off-by: Marek Vasut Cc: Tom Rini Cc: Stefano Babic diff --git a/tools/Makefile b/tools/Makefile index bbae5a2..f4ca1cf 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -70,32 +70,32 @@ EXT_OBJ_FILES-y += lib/md5.o EXT_OBJ_FILES-y += lib/sha1.o # Source files located in the tools directory -OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o -OBJ_FILES-$(CONFIG_VIDEO_LOGO) += bmp_logo.o +NOPED_OBJ_FILES-y += aisimage.o NOPED_OBJ_FILES-y += default_image.o -NOPED_OBJ_FILES-y += proftool.o -OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o NOPED_OBJ_FILES-y += fit_image.o -OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o -OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o -OBJ_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes.o -NOPED_OBJ_FILES-y += aisimage.o -NOPED_OBJ_FILES-y += kwbimage.o -NOPED_OBJ_FILES-y += pblimage.o -NOPED_OBJ_FILES-y += imximage.o -NOPED_OBJ_FILES-y += mxsimage.o NOPED_OBJ_FILES-y += image-host.o -NOPED_OBJ_FILES-y += omapimage.o +NOPED_OBJ_FILES-y += imximage.o +NOPED_OBJ_FILES-y += kwbimage.o NOPED_OBJ_FILES-y += mkenvimage.o NOPED_OBJ_FILES-y += mkimage.o -OBJ_FILES-$(CONFIG_SMDK5250) += mkexynosspl.o +NOPED_OBJ_FILES-y += mxsimage.o +NOPED_OBJ_FILES-y += omapimage.o +NOPED_OBJ_FILES-y += os_support.o +NOPED_OBJ_FILES-y += pblimage.o +NOPED_OBJ_FILES-y += proftool.o +NOPED_OBJ_FILES-y += ublimage.o +OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o +OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o +OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o +OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o +OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o OBJ_FILES-$(CONFIG_MX23) += mxsboot.o OBJ_FILES-$(CONFIG_MX28) += mxsboot.o OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o -NOPED_OBJ_FILES-y += os_support.o OBJ_FILES-$(CONFIG_SHA1_CHECK_UB_IMG) += ubsha1.o -NOPED_OBJ_FILES-y += ublimage.o -OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o +OBJ_FILES-$(CONFIG_SMDK5250) += mkexynosspl.o +OBJ_FILES-$(CONFIG_VIDEO_LOGO) += bmp_logo.o +OBJ_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes.o # Don't build by default #ifeq ($(ARCH),ppc) @@ -202,21 +202,21 @@ $(obj)mkenvimage$(SFX): $(obj)crc32.o $(obj)mkenvimage.o \ $(HOSTSTRIP) $@ $(obj)mkimage$(SFX): $(obj)aisimage.o \ + $(FIT_SIG_OBJS) \ $(obj)crc32.o \ $(obj)default_image.o \ $(obj)fit_image.o \ $(obj)image-fit.o \ - $(obj)image.o \ $(obj)image-host.o \ - $(FIT_SIG_OBJS) \ + $(obj)image.o \ $(obj)imximage.o \ - $(obj)mxsimage.o \ $(obj)kwbimage.o \ - $(obj)pblimage.o \ $(obj)md5.o \ $(obj)mkimage.o \ - $(obj)os_support.o \ + $(obj)mxsimage.o \ $(obj)omapimage.o \ + $(obj)os_support.o \ + $(obj)pblimage.o \ $(obj)sha1.o \ $(obj)ublimage.o \ $(LIBFDT_OBJS) \ -- cgit v0.10.2 From 62d40d14c4368593b0b1afdff8f008b260497a58 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 27 Aug 2013 23:32:37 +0200 Subject: tools: mxsboot: Staticize functions Make remaining non-static functions static and the same for vars. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Stefano Babic diff --git a/tools/mxsboot.c b/tools/mxsboot.c index 3d9cc10..1060cbf 100644 --- a/tools/mxsboot.c +++ b/tools/mxsboot.c @@ -28,14 +28,14 @@ * * TWEAK this if you have different kind of NAND chip. */ -uint32_t nand_writesize = 2048; -uint32_t nand_oobsize = 64; -uint32_t nand_erasesize = 128 * 1024; +static uint32_t nand_writesize = 2048; +static uint32_t nand_oobsize = 64; +static uint32_t nand_erasesize = 128 * 1024; /* * Sector on which the SigmaTel boot partition (0x53) starts. */ -uint32_t sd_sector = 2048; +static uint32_t sd_sector = 2048; /* * Each of the U-Boot bootstreams is at maximum 1MB big. @@ -434,7 +434,7 @@ static int mx28_nand_write_firmware(struct mx28_nand_fcb *fcb, int infd, return 0; } -void usage(void) +static void usage(void) { printf( "Usage: mxsboot [ops] \n" @@ -575,7 +575,7 @@ err0: return ret; } -int parse_ops(int argc, char **argv) +static int parse_ops(int argc, char **argv) { int i; int tmp; -- cgit v0.10.2 From 518501da4c9d05e6ac87908fbad79d8e10e4b0e4 Mon Sep 17 00:00:00 2001 From: SARTRE Leo Date: Thu, 20 Jun 2013 15:46:50 +0200 Subject: ARM: Congatec: README update README: U-boot works both on SPI-NOR and SDcard Signed-off-by: Leo Sartre Acked-by: Otavio Salvador diff --git a/board/congatec/cgtqmx6eval/README b/board/congatec/cgtqmx6eval/README index bbf0f75..5e76d2a 100644 --- a/board/congatec/cgtqmx6eval/README +++ b/board/congatec/cgtqmx6eval/README @@ -7,8 +7,7 @@ Conga-QEVAl Evaluation Carrier board with qmx6 quad module. 1. Boot source, boot from SD card --------------------------------- -This version of u-boot works only on the SD card. By default, the -Congatec board can boot only from the SPI-NOR. +By default, the Congatec board can boot only from the SPI-NOR. But, with the u-boot version provided with the board you can write boot registers to force the board to reboot and boot from the SD slot. If "bmode" command is not available from your pre-installed u-boot, these -- cgit v0.10.2 From 6f6059e0f102809bcba1ea3b7d500c3e4f5f9581 Mon Sep 17 00:00:00 2001 From: Hector Palacios Date: Wed, 24 Jul 2013 16:01:39 +0200 Subject: ARM: mxs: rename function that sets AUTO_RESTART flag The AUTO_RESTART flag of HW_RTC_PERSISTENT0 register will power up the chip automatically 180ms after power down. This bit must be enabled by the boot loader to ensure the target can start upon hardware reset or watchdog reset even when powered from a battery. Currently the function named 'mxs_power_clear_auto_restart()' is setting this flag although the 'clear' in its name suggest the opposite. This patch renames the function to 'mxs_power_set_auto_restart()' and removes the comment about EVK revision A which was confusing because the function indeed was setting the flag. Signed-off-by: Hector Palacios diff --git a/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c b/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c index e3b6cd9..f357959 100644 --- a/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c +++ b/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c @@ -36,7 +36,7 @@ static void mxs_power_clock2pll(void) CLKCTRL_CLKSEQ_BYPASS_CPU); } -static void mxs_power_clear_auto_restart(void) +static void mxs_power_set_auto_restart(void) { struct mxs_rtc_regs *rtc_regs = (struct mxs_rtc_regs *)MXS_RTC_BASE; @@ -49,10 +49,7 @@ static void mxs_power_clear_auto_restart(void) while (readl(&rtc_regs->hw_rtc_ctrl) & RTC_CTRL_CLKGATE) ; - /* - * Due to the hardware design bug of mx28 EVK-A - * we need to set the AUTO_RESTART bit. - */ + /* Do nothing if flag already set */ if (readl(&rtc_regs->hw_rtc_persistent0) & RTC_PERSISTENT0_AUTO_RESTART) return; @@ -911,7 +908,7 @@ void mxs_power_init(void) mxs_ungate_power(); mxs_power_clock2xtal(); - mxs_power_clear_auto_restart(); + mxs_power_set_auto_restart(); mxs_power_set_linreg(); mxs_power_setup_5v_detect(); -- cgit v0.10.2 From 1ca244ded50de4b5f39ded2793a02fe5f17f9ba6 Mon Sep 17 00:00:00 2001 From: Eric Nelson Date: Thu, 29 Aug 2013 10:57:10 -0700 Subject: i.MX6: Add convenience macros cpu_type(rev) and is_cpu_type(cpu) Signed-off-by: Eric Nelson Acked-by: Stefano Babic diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h index bfdfd29..8c21364 100644 --- a/arch/arm/include/asm/arch-mx6/sys_proto.h +++ b/arch/arm/include/asm/arch-mx6/sys_proto.h @@ -19,6 +19,13 @@ #define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev) u32 get_cpu_rev(void); + +/* returns MXC_CPU_ value */ +#define cpu_type(rev) (((rev) >> 12)&0xff) + +/* use with MXC_CPU_ constants */ +#define is_cpu_type(cpu) (cpu_type(get_cpu_rev()) == cpu) + const char *get_imx_type(u32 imxtype); unsigned imx_ddr_size(void); -- cgit v0.10.2 From 3fc4176dc4b61bc50b0d90f10eef48f7b2e28203 Mon Sep 17 00:00:00 2001 From: Eric Nelson Date: Thu, 29 Aug 2013 12:37:35 -0700 Subject: i.MX6: Correct ANATOP_PFD (Phase Fractional Divider) register declarations Some _CLKGATE_MASK and _FRAC_MASK macros were wrong for PFD_480 and the PFD_528 macros were missing. Fortunately, the incorrect macros weren't being used. Since both the PFD_480 and PFD_528 registers have the same structure, and the fields are identical for [0..3] in bytes [0..3], so a single set of macros will suffice. Signed-off-by: Eric Nelson diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h index 621919f..7ef7152 100644 --- a/arch/arm/include/asm/arch-mx6/imx-regs.h +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h @@ -635,29 +635,12 @@ struct anatop_regs { u32 digprog_sololite; /* 0x280 */ }; -#define ANATOP_PFD_480_PFD0_FRAC_SHIFT 0 -#define ANATOP_PFD_480_PFD0_FRAC_MASK (0x3f< Date: Thu, 29 Aug 2013 12:37:36 -0700 Subject: i.MX6: nitrogen6x: Don't bother setting PLL3(480) PFD1 divisor This clock isn't feeding anything under U-Boot, so there's no point in changing it from power-on default. Signed-off-by: Eric Nelson diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index 1419f36..f664f6d 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -622,7 +622,6 @@ int board_video_skip(void) static void setup_display(void) { struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; - struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; int reg; @@ -633,10 +632,6 @@ static void setup_display(void) reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; writel(reg, &mxc_ccm->CCGR3); - /* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */ - writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr); - writel(0x13<pfd_480_set); - /* set LDB0, LDB1 clk select to 011/011 */ reg = readl(&mxc_ccm->cs2cdr); reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK -- cgit v0.10.2 From 8467faef7fce8c5faad7224b7737a58e16c52186 Mon Sep 17 00:00:00 2001 From: Eric Nelson Date: Thu, 29 Aug 2013 12:41:46 -0700 Subject: i.MX6: Set and clear the gating bits for Phase Fractional Dividers This addresses silicon errata ERR006282 as described in this document: https://community.freescale.com/docs/DOC-94581 Also implemented in Freescale's 2009.08-based release: http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/ Commit id: b7c5badf94ffbe6cd0845efbb75e16e05e3af404 Signed-off-by: Eric Nelson Acked-by: Stefano Babic diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index 8150bff..a390296 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -213,6 +213,34 @@ const struct boot_mode soc_boot_modes[] = { void s_init(void) { + struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; + int is_6q = is_cpu_type(MXC_CPU_MX6Q); + u32 mask480; + u32 mask528; + + /* Due to hardware limitation, on MX6Q we need to gate/ungate all PFDs + * to make sure PFD is working right, otherwise, PFDs may + * not output clock after reset, MX6DL and MX6SL have added 396M pfd + * workaround in ROM code, as bus clock need it + */ + + mask480 = ANATOP_PFD_CLKGATE_MASK(0) | + ANATOP_PFD_CLKGATE_MASK(1) | + ANATOP_PFD_CLKGATE_MASK(2) | + ANATOP_PFD_CLKGATE_MASK(3); + mask528 = ANATOP_PFD_CLKGATE_MASK(0) | + ANATOP_PFD_CLKGATE_MASK(1) | + ANATOP_PFD_CLKGATE_MASK(3); + + /* + * Don't reset PFD2 on DL/S + */ + if (is_6q) + mask528 |= ANATOP_PFD_CLKGATE_MASK(2); + writel(mask480, &anatop->pfd_480_set); + writel(mask528, &anatop->pfd_528_set); + writel(mask480, &anatop->pfd_480_clr); + writel(mask528, &anatop->pfd_528_clr); } #ifdef CONFIG_IMX_HDMI -- cgit v0.10.2