From e07f4a8033b6270b8103049adb6456f660ff4a89 Mon Sep 17 00:00:00 2001 From: Ricardo Ribalda Delgado Date: Mon, 1 Sep 2008 13:09:39 -0400 Subject: ppc44x: Unification of virtex5 pp440 boards This patch provides an unificated way of handling xilinx v5 ppc440 boards. It unificates 3 different things: 1) Source code A new board called ppc440-generic has been created. This board includes a generic tlb initialization (Maps the whole memory into virtual) and defines board_pre_init, checkboard, initdram and get_sys_info weakly, so, they can be replaced by specific functions. If a new board needs to redefine any of the previous functions (specific initialization) it can create a new directory with the specific initializations needed. (see the example ml507 board). 2) Configuration file Common configurations are located under configs/xilinx-ppc440.h, this header file interpretes the xparameters file generated by EDK and configurates u-boot in correspondence. Example: if there is a Temac, allows CMD_CONFIG_NET Specific configuration are located under specific configuration file. (see the example ml507 board) 3) Makefile Some work has been done in order to not duplicate work in the Main Makefile. Please see the attached code. In order to support new boards they can be implemented in the next way: a) Simple Generic Board (90% of the time) Using EDK generates a new xparameters.h file, replace ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config && make b) Simple Boards with special u-boot parameters (9 % of the time) Create a new file under configs for it (use ml507.h as example) and change your paramaters. Create a new Makefile paragraph and compile c) Complex boards (1% of the time) Create a new folder for the board, like the ml507 Finally, it adds support for the Avnet FX30T Evaluation board, following the new generic structure: Cheap board by Avnet for evaluating the Virtex5 FX technology. This patch adds support for: - UartLite - 16MB Flash - 64MB RAM Prior using U-boot in this board, read carefully the ERRATA by Avnet to solve some memory initialization issues. Signed-off-by: Ricardo Ribalda Delgado Signed-off-by: Stefan Roese diff --git a/CREDITS b/CREDITS index 4fe4e63..3767322 100644 --- a/CREDITS +++ b/CREDITS @@ -405,7 +405,8 @@ D: Atmel AT91CAP9ADK support N: Ricardo Ribalda Delgado E: ricardo.ribalda@uam.es -D: PPC440x5 (Virtex5), ML507 Board, eeprom_simul, adt7460 +D: PPC440x5 (Virtex5), ML507 Board, eeprom_simul, adt7460, v5fx30teval +D: Virtex ppc440 generic architecture W: http://www.ii.uam.es/~rribalda N: Stefan Roese diff --git a/MAINTAINERS b/MAINTAINERS index 3f16dab..64d8409 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -314,6 +314,8 @@ Daniel Poirot Ricardo Ribalda ml507 PPC440x5 + v5fx30teval PPC440x5 + xilinx-pp440-generic PPC440x5 Stefan Roese diff --git a/MAKEALL b/MAKEALL index fbdcb42..9ccb9ac 100755 --- a/MAKEALL +++ b/MAKEALL @@ -230,12 +230,16 @@ LIST_4xx=" \ sequoia_nand \ taihu \ taishan \ + v5fx30teval \ + v5fx30teval_flash \ VOH405 \ VOM405 \ W7OLMC \ W7OLMG \ walnut \ WUH405 \ + xilinx-ppc440-generic \ + xilinx-ppc440-generic_flash \ XPEDITE1K \ yellowstone \ yosemite \ diff --git a/Makefile b/Makefile index 8d82ef5..3869e79 100644 --- a/Makefile +++ b/Makefile @@ -1356,16 +1356,17 @@ ML2_config: unconfig ml300_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx ml300 xilinx -ml507_flash_config: unconfig +ml507_flash_config: unconfig @mkdir -p $(obj)include $(obj)board/xilinx/ml507 - @cp $(obj)board/xilinx/ml507/u-boot-rom.lds $(obj)board/xilinx/ml507/u-boot.lds - @echo "TEXT_BASE = 0xFE360000" > $(obj)board/xilinx/ml507/config.tmp - @$(MKCONFIG) $(@:_flash_config=) ppc ppc4xx ml507 xilinx + @echo "LDSCRIPT := $(obj)board/xilinx/ppc440-generic/u-boot-rom.lds" > $(obj)board/xilinx/ml507/config.mk + @echo "TEXT_BASE := 0xFE360000" >> $(obj)board/xilinx/ml507/config.mk + @$(MKCONFIG) ml507 ppc ppc4xx ml507 xilinx -ml507_config: unconfig +ml507_config: unconfig @mkdir -p $(obj)include $(obj)board/xilinx/ml507 - @cp $(obj)board/xilinx/ml507/u-boot-ram.lds $(obj)board/xilinx/ml507/u-boot.lds - @$(MKCONFIG) $(@:_config=) ppc ppc4xx ml507 xilinx + @echo "LDSCRIPT := $(obj)board/xilinx/ppc440-generic/u-boot-ram.lds" > $(obj)board/xilinx/ml507/config.mk + @echo "TEXT_BASE := 0x04000000" >> $(obj)board/xilinx/ml507/config.mk + @$(MKCONFIG) ml507 ppc ppc4xx ml507 xilinx ocotea_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx ocotea amcc @@ -1461,6 +1462,18 @@ taihu_config: unconfig taishan_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx taishan amcc +v5fx30teval_config: unconfig + @mkdir -p $(obj)include $(obj)board/avnet/v5fx30teval + @echo "LDSCRIPT := $(obj)board/xilinx/ppc440-generic/u-boot-ram.lds" > $(obj)board/avnet/v5fx30teval/config.mk + @echo "TEXT_BASE := 0x03000000" >> $(obj)board/avnet/v5fx30teval/config.mk + @$(MKCONFIG) v5fx30teval ppc ppc4xx v5fx30teval avnet + +v5fx30teval_flash_config: unconfig + @mkdir -p $(obj)include $(obj)board/avnet/v5fx30teval + @echo "LDSCRIPT := $(obj)board/xilinx/ppc440-generic/u-boot-rom.lds" > $(obj)board/avnet/v5fx30teval/config.mk + @echo "TEXT_BASE := 0xFF1C0000" >> $(obj)board/avnet/v5fx30teval/config.mk + @$(MKCONFIG) v5fx30teval ppc ppc4xx v5fx30teval avnet + VOH405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx voh405 esd @@ -1479,6 +1492,18 @@ sycamore_config: unconfig WUH405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx wuh405 esd +xilinx-ppc440-generic_flash_config: unconfig + @mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic/ + @echo "LDSCRIPT := $(obj)board/xilinx/ppc440-generic/u-boot-rom.lds" > $(obj)board/xilinx/ppc440-generic/config.mk + @echo "TEXT_BASE := 0xFE360000" >> $(obj)board/xilinx/ppc440-generic/config.mk + @$(MKCONFIG) xilinx-ppc440-generic ppc ppc4xx ppc440-generic xilinx + +xilinx-ppc440-generic_config: unconfig + @mkdir -p $(obj)include $(obj)board/xilinx/ppc440-generic/ + @echo "LDSCRIPT := $(obj)board/xilinx/ppc440-generic/u-boot-ram.lds" > $(obj)board/xilinx/ppc440-generic/config.mk + @echo "TEXT_BASE := 0x04000000" >> $(obj)board/xilinx/ppc440-generic/config.mk + @$(MKCONFIG) xilinx-ppc440-generic ppc ppc4xx ppc440-generic xilinx + XPEDITE1K_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx xpedite1k diff --git a/board/avnet/v5fx30teval/.gitignore b/board/avnet/v5fx30teval/.gitignore new file mode 100644 index 0000000..6896ef6 --- /dev/null +++ b/board/avnet/v5fx30teval/.gitignore @@ -0,0 +1 @@ +/config.mk diff --git a/board/avnet/v5fx30teval/Makefile b/board/avnet/v5fx30teval/Makefile new file mode 100644 index 0000000..de23f29 --- /dev/null +++ b/board/avnet/v5fx30teval/Makefile @@ -0,0 +1,27 @@ +# +# (C) Copyright 2008 +# Ricardo Ribalda,Universidad Autonoma de Madrid, ricardo.ribalda@uam.es +# This work has been supported by: Qtechnology http://qtec.com/ +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +COBJS += $(BOARD).o + +include $(SRCTREE)/board/xilinx/ppc440-generic/Makefile diff --git a/board/avnet/v5fx30teval/v5fx30teval.c b/board/avnet/v5fx30teval/v5fx30teval.c new file mode 100644 index 0000000..14a1d5d --- /dev/null +++ b/board/avnet/v5fx30teval/v5fx30teval.c @@ -0,0 +1,28 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#include +#include +#include + + +int checkboard(void) +{ + puts("Avnet Virtex 5 FX30 Evaluation Board\n"); + return 0; +} diff --git a/board/avnet/v5fx30teval/xparameters.h b/board/avnet/v5fx30teval/xparameters.h new file mode 100644 index 0000000..bb657fc --- /dev/null +++ b/board/avnet/v5fx30teval/xparameters.h @@ -0,0 +1,33 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * based on xparameters.h by Xilinx + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#ifndef XPARAMETER_H +#define XPARAMETER_H + +#define XPAR_DDR2_SDRAM_MEM_BASEADDR 0x00000000 +#define XPAR_INTC_0_BASEADDR 0x81800000 +#define XPAR_UARTLITE_0_BASEADDR 0x84000000 +#define XPAR_FLASH_MEM0_BASEADDR 0xFF000000 +#define XPAR_PLB_CLOCK_FREQ_HZ 100000000 +#define XPAR_CORE_CLOCK_FREQ_HZ 400000000 +#define XPAR_INTC_MAX_NUM_INTR_INPUTS 13 +#define XPAR_UARTLITE_0_BAUDRATE 9600 + +#endif diff --git a/board/xilinx/ml507/.gitignore b/board/xilinx/ml507/.gitignore new file mode 100644 index 0000000..6896ef6 --- /dev/null +++ b/board/xilinx/ml507/.gitignore @@ -0,0 +1 @@ +/config.mk diff --git a/board/xilinx/ml507/Makefile b/board/xilinx/ml507/Makefile index 7283704..de23f29 100644 --- a/board/xilinx/ml507/Makefile +++ b/board/xilinx/ml507/Makefile @@ -1,6 +1,7 @@ # -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# (C) Copyright 2008 +# Ricardo Ribalda,Universidad Autonoma de Madrid, ricardo.ribalda@uam.es +# This work has been supported by: Qtechnology http://qtec.com/ # # See file CREDITS for list of people who contributed to this # project. @@ -21,38 +22,6 @@ # MA 02111-1307 USA # -include $(TOPDIR)/config.mk -ifneq ($(OBJTREE),$(SRCTREE)) -endif +COBJS += $(BOARD).o -INCS := -CFLAGS += $(INCS) -HOST_CFLAGS += $(INCS) - -LIB = $(obj)lib$(BOARD).a - -COBJS = $(BOARD).o - -SOBJS = init.o - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(OBJS) $(SOBJS) - $(AR) $(ARFLAGS) $@ $^ - -clean: - rm -f $(SOBJS) $(OBJS) - -distclean: clean - rm -f $(LIB) core *.bak .depend - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### +include $(SRCTREE)/board/xilinx/ppc440-generic/Makefile diff --git a/board/xilinx/ml507/config.mk b/board/xilinx/ml507/config.mk deleted file mode 100644 index e827e8a..0000000 --- a/board/xilinx/ml507/config.mk +++ /dev/null @@ -1,27 +0,0 @@ -# -# (C) Copyright 2000 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# -sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp - -ifndef TEXT_BASE -TEXT_BASE = 0x04000000 -endif diff --git a/board/xilinx/ml507/init.S b/board/xilinx/ml507/init.S deleted file mode 100644 index 3228a65..0000000 --- a/board/xilinx/ml507/init.S +++ /dev/null @@ -1,53 +0,0 @@ -/* - * (C) Copyright 2008 - * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es - * This work has been supported by: QTechnology http://qtec.com/ - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . -*/ - -#include -#include -#include - -.section .bootpg,"ax" -.globl tlbtab - -tlbtab: -tlbtab_start - /* SDRAM */ -tlbentry(XPAR_DDR2_SDRAM_MEM_BASEADDR, SZ_256M, CFG_SDRAM_BASE, 0, - AC_R | AC_W | AC_X | SA_G | SA_I) - /* UART */ -tlbentry(XPAR_UARTLITE_0_BASEADDR, SZ_64K, XPAR_UARTLITE_0_BASEADDR, 0, - AC_R | AC_W | SA_G | SA_I) - /* PIC */ -tlbentry(XPAR_INTC_0_BASEADDR, SZ_64K, XPAR_INTC_0_BASEADDR, 0, - AC_R | AC_W | SA_G | SA_I) -#ifdef XPAR_IIC_EEPROM_BASEADDR - /* I2C */ -tlbentry(XPAR_IIC_EEPROM_BASEADDR, SZ_64K, XPAR_IIC_EEPROM_BASEADDR, 0, - AC_R | AC_W | SA_G | SA_I) -#endif -#ifdef XPAR_LLTEMAC_0_BASEADDR - /* Net */ -tlbentry(XPAR_LLTEMAC_0_BASEADDR, SZ_64K, XPAR_LLTEMAC_0_BASEADDR, 0, - AC_R | AC_W | SA_G | SA_I) -#endif -#ifdef XPAR_FLASH_MEM0_BASEADDR - /*Flash*/ -tlbentry(XPAR_FLASH_MEM0_BASEADDR, SZ_256M, XPAR_FLASH_MEM0_BASEADDR, 0, - AC_R | AC_W | AC_X | SA_G | SA_I) -#endif -tlbtab_end diff --git a/board/xilinx/ml507/ml507.c b/board/xilinx/ml507/ml507.c index d499303..f9789cf 100644 --- a/board/xilinx/ml507/ml507.c +++ b/board/xilinx/ml507/ml507.c @@ -20,28 +20,9 @@ #include #include -int board_pre_init(void) -{ - return 0; -} int checkboard(void) { - puts("ML507 Board\n"); + puts("Xilinx ML507 Board\n"); return 0; } - -phys_size_t initdram(int board_type) -{ - return get_ram_size(XPAR_DDR2_SDRAM_MEM_BASEADDR, - CFG_SDRAM_SIZE_MB * 1024 * 1024); -} - -void get_sys_info(sys_info_t * sysInfo) -{ - sysInfo->freqProcessor = XPAR_CORE_CLOCK_FREQ_HZ; - sysInfo->freqPLB = XPAR_PLB_CLOCK_FREQ_HZ; - sysInfo->freqPCI = 0; - - return; -} diff --git a/board/xilinx/ml507/u-boot-ram.lds b/board/xilinx/ml507/u-boot-ram.lds deleted file mode 100644 index 2c98d27..0000000 --- a/board/xilinx/ml507/u-boot-ram.lds +++ /dev/null @@ -1,134 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -OUTPUT_ARCH(powerpc) -ENTRY(_start_440) - -SECTIONS -{ - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - - - *(.text) - *(.fixup) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.rodata) - *(.rodata1) - *(.rodata.str1.4) - *(.eh_frame) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - __u_boot_cmd_start = .; - .u_boot_cmd : { *(.u_boot_cmd) } - __u_boot_cmd_end = .; - - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - } - - ppcenv_assert = ASSERT(. < 0xFFFFB000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); - - _end = . ; - PROVIDE (end = .); -} diff --git a/board/xilinx/ml507/u-boot-rom.lds b/board/xilinx/ml507/u-boot-rom.lds deleted file mode 100644 index d5da018..0000000 --- a/board/xilinx/ml507/u-boot-rom.lds +++ /dev/null @@ -1,144 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -OUTPUT_ARCH(powerpc) -ENTRY(_start_440) - -SECTIONS -{ - .resetvec 0xFFFFFFFC : - { - *(.resetvec) - } = 0xffff - - .bootpg 0xFFFFF000 : - { - cpu/ppc4xx/start.o (.bootpg) - } = 0xffff - - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - - - *(.text) - *(.fixup) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.rodata) - *(.rodata1) - *(.rodata.str1.4) - *(.eh_frame) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - __u_boot_cmd_start = .; - .u_boot_cmd : { *(.u_boot_cmd) } - __u_boot_cmd_end = .; - - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - } - - ppcenv_assert = ASSERT(. < 0xFFFFB000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); - - _end = . ; - PROVIDE (end = .); -} diff --git a/board/xilinx/ml507/xparameters.h b/board/xilinx/ml507/xparameters.h index 77d2ddf..1992fff 100644 --- a/board/xilinx/ml507/xparameters.h +++ b/board/xilinx/ml507/xparameters.h @@ -21,15 +21,14 @@ #ifndef XPARAMETER_H #define XPARAMETER_H -#define XPAR_DDR2_SDRAM_MEM_BASEADDR 0x00000000 -#define XPAR_IIC_EEPROM_BASEADDR 0x81600000 -#define XPAR_INTC_0_BASEADDR 0x81800000 -#define XPAR_LLTEMAC_0_BASEADDR 0x81C00000 -#define XPAR_UARTLITE_0_BASEADDR 0x84000000 -#define XPAR_FLASH_MEM0_BASEADDR 0xFE000000 -#define XPAR_PLB_CLOCK_FREQ_HZ 100000000 -#define XPAR_CORE_CLOCK_FREQ_HZ 400000000 -#define XPAR_INTC_MAX_NUM_INTR_INPUTS 13 +#define XPAR_DDR2_SDRAM_MEM_BASEADDR 0x00000000 +#define XPAR_IIC_EEPROM_BASEADDR 0x81600000 +#define XPAR_INTC_0_BASEADDR 0x81800000 +#define XPAR_UARTLITE_0_BASEADDR 0x84000000 +#define XPAR_FLASH_MEM0_BASEADDR 0xFE000000 +#define XPAR_PLB_CLOCK_FREQ_HZ 100000000 +#define XPAR_CORE_CLOCK_FREQ_HZ 400000000 +#define XPAR_INTC_MAX_NUM_INTR_INPUTS 13 #define XPAR_UARTLITE_0_BAUDRATE 9600 #endif diff --git a/board/xilinx/ppc440-generic/.gitignore b/board/xilinx/ppc440-generic/.gitignore new file mode 100644 index 0000000..6896ef6 --- /dev/null +++ b/board/xilinx/ppc440-generic/.gitignore @@ -0,0 +1 @@ +/config.mk diff --git a/board/xilinx/ppc440-generic/Makefile b/board/xilinx/ppc440-generic/Makefile new file mode 100644 index 0000000..f7405a8 --- /dev/null +++ b/board/xilinx/ppc440-generic/Makefile @@ -0,0 +1,62 @@ +# +# (C) Copyright 2000-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2008 +# Ricardo Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es +# Work supported by Qtechnology http://www.qtec.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +ifneq ($(OBJTREE),$(SRCTREE)) +endif + +INCS := +CFLAGS += $(INCS) +HOST_CFLAGS += $(INCS) + +LIB = $(obj)lib$(BOARD).a + +COBJS += $(SRCTREE)/board/xilinx/ppc440-generic/xilinx_ppc440_generic.o + +SOBJS += $(SRCTREE)/board/xilinx/ppc440-generic/init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $^ + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xilinx/ppc440-generic/init.S b/board/xilinx/ppc440-generic/init.S new file mode 100644 index 0000000..1409467 --- /dev/null +++ b/board/xilinx/ppc440-generic/init.S @@ -0,0 +1,45 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#include +#include +#include + +.section .bootpg,"ax" +.globl tlbtab + +tlbtab: +tlbtab_start +tlbentry(0x00000000, SZ_256M, 0x00000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x10000000, SZ_256M, 0x10000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x20000000, SZ_256M, 0x20000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x30000000, SZ_256M, 0x30000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x40000000, SZ_256M, 0x40000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x50000000, SZ_256M, 0x50000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x60000000, SZ_256M, 0x60000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x70000000, SZ_256M, 0x70000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x80000000, SZ_256M, 0x80000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0x90000000, SZ_256M, 0x90000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0xa0000000, SZ_256M, 0xa0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0xb0000000, SZ_256M, 0xb0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0xc0000000, SZ_256M, 0xc0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0xd0000000, SZ_256M, 0xd0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0xe0000000, SZ_256M, 0xe0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbentry(0xf0000000, SZ_256M, 0xf0000000, 0, AC_R | AC_W | AC_X | SA_G | SA_I) +tlbtab_end diff --git a/board/xilinx/ppc440-generic/u-boot-ram.lds b/board/xilinx/ppc440-generic/u-boot-ram.lds new file mode 100644 index 0000000..2c98d27 --- /dev/null +++ b/board/xilinx/ppc440-generic/u-boot-ram.lds @@ -0,0 +1,134 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +ENTRY(_start_440) + +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + + ppcenv_assert = ASSERT(. < 0xFFFFB000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); + + _end = . ; + PROVIDE (end = .); +} diff --git a/board/xilinx/ppc440-generic/u-boot-rom.lds b/board/xilinx/ppc440-generic/u-boot-rom.lds new file mode 100644 index 0000000..d5da018 --- /dev/null +++ b/board/xilinx/ppc440-generic/u-boot-rom.lds @@ -0,0 +1,144 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +ENTRY(_start_440) + +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/ppc4xx/start.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss (NOLOAD) : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + + ppcenv_assert = ASSERT(. < 0xFFFFB000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); + + _end = . ; + PROVIDE (end = .); +} diff --git a/board/xilinx/ppc440-generic/xilinx_ppc440_generic.c b/board/xilinx/ppc440-generic/xilinx_ppc440_generic.c new file mode 100644 index 0000000..0867226 --- /dev/null +++ b/board/xilinx/ppc440-generic/xilinx_ppc440_generic.c @@ -0,0 +1,52 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#include +#include +#include + +int __board_pre_init(void) +{ + return 0; +} +int board_pre_init(void) __attribute__((weak, alias("__board_pre_init"))); + +int __checkboard(void) +{ + puts("Xilinx PPC440 Generic Board\n"); + return 0; +} +int checkboard(void) __attribute__((weak, alias("__checkboard"))); + +phys_size_t __initdram(int board_type) +{ + return get_ram_size(XPAR_DDR2_SDRAM_MEM_BASEADDR, + CFG_SDRAM_SIZE_MB * 1024 * 1024); +} +phys_size_t initdram(int) __attribute__((weak, alias("__initdram"))); + +void __get_sys_info(sys_info_t *sysInfo) +{ + sysInfo->freqProcessor = XPAR_CORE_CLOCK_FREQ_HZ; + sysInfo->freqPLB = XPAR_PLB_CLOCK_FREQ_HZ; + sysInfo->freqPCI = 0; + + return; +} +void get_sys_info(sys_info_t *) __attribute__((weak, alias("__get_sys_info"))); diff --git a/board/xilinx/ppc440-generic/xparameters.h b/board/xilinx/ppc440-generic/xparameters.h new file mode 100644 index 0000000..1992fff --- /dev/null +++ b/board/xilinx/ppc440-generic/xparameters.h @@ -0,0 +1,34 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * based on xparameters-ml507.h by Xilinx + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#ifndef XPARAMETER_H +#define XPARAMETER_H + +#define XPAR_DDR2_SDRAM_MEM_BASEADDR 0x00000000 +#define XPAR_IIC_EEPROM_BASEADDR 0x81600000 +#define XPAR_INTC_0_BASEADDR 0x81800000 +#define XPAR_UARTLITE_0_BASEADDR 0x84000000 +#define XPAR_FLASH_MEM0_BASEADDR 0xFE000000 +#define XPAR_PLB_CLOCK_FREQ_HZ 100000000 +#define XPAR_CORE_CLOCK_FREQ_HZ 400000000 +#define XPAR_INTC_MAX_NUM_INTR_INPUTS 13 +#define XPAR_UARTLITE_0_BAUDRATE 9600 + +#endif diff --git a/include/configs/ml507.h b/include/configs/ml507.h index f8cd499..37d93bb 100644 --- a/include/configs/ml507.h +++ b/include/configs/ml507.h @@ -17,106 +17,33 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* -#define DEBUG -#define ET_DEBUG -*/ - /*CPU*/ -#define CONFIG_XILINX_ML507 1 -#define CONFIG_XILINX_440 1 + +/*CPU*/ #define CONFIG_440 1 -#define CONFIG_4xx 1 +#define CONFIG_XILINX_ML507 1 #include "../board/xilinx/ml507/xparameters.h" /*Mem Map*/ -#define CFG_SDRAM_BASE 0x0 #define CFG_SDRAM_SIZE_MB 256 -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN ( 192 * 1024 ) -#define CFG_MALLOC_LEN ( CFG_ENV_SIZE + 128 * 1024 ) - -/*Uart*/ -#define CONFIG_XILINX_UARTLITE -#define CONFIG_BAUDRATE XPAR_UARTLITE_0_BAUDRATE -#define CFG_BAUDRATE_TABLE { XPAR_UARTLITE_0_BAUDRATE } -#define CONFIG_SERIAL_BASE XPAR_UARTLITE_0_BASEADDR - -/*Cmd*/ -#include -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_JFFS2 -#define CONFIG_JFFS2_CMDLINE -#undef CONFIG_CMD_I2C -#undef CONFIG_CMD_DTT -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_PING -#undef CONFIG_CMD_DHCP -#undef CONFIG_CMD_EEPROM -#undef CONFIG_CMD_IMLS /*Env*/ -#define CFG_ENV_IS_IN_FLASH +#define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SIZE 0x20000 #define CFG_ENV_SECT_SIZE 0x20000 -#define CFG_ENV_OFFSET 0x340000 -#define CFG_ENV_ADDR (XPAR_FLASH_MEM0_BASEADDR+CFG_ENV_OFFSET) +#define CFG_ENV_OFFSET 0x340000 +#define CFG_ENV_ADDR (XPAR_FLASH_MEM0_BASEADDR+CFG_ENV_OFFSET) /*Misc*/ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "board:/# " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE ( CFG_CBSIZE + sizeof( CFG_PROMPT ) + 16 ) -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x00400000 /* default load address */ -#define CFG_EXTBDINFO 1 /* Extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_CMDLINE_EDITING /* add command line history */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_LOOPW /* enable loopw command */ -#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET /* don't print console @ startup */ -#define CFG_HUSH_PARSER /* Use the HUSH parser */ -#define CFG_PROMPT_HUSH_PS2 "> " -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ -#define CFG_BOOTMAPSZ ( 8 << 20 ) /* Initial Memory map for Linux */ +#define CFG_PROMPT "ml507:/# " /* Monitor Command Prompt */ #define CONFIG_PREBOOT "echo U-Boot is up and runnining;" -/*Stack*/ -#define CFG_INIT_RAM_ADDR 0x800000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET ( CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE ) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -/*Speed*/ -#define CONFIG_SYS_CLK_FREQ XPAR_CORE_CLOCK_FREQ_HZ - /*Flash*/ -#define CFG_FLASH_BASE XPAR_FLASH_MEM0_BASEADDR #define CFG_FLASH_SIZE (32*1024*1024) -#define CFG_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CFG_FLASH_EMPTY_INFO 1 -#define CFG_MAX_FLASH_BANKS 1 #define CFG_MAX_FLASH_SECT 259 -#define CFG_FLASH_PROTECTION #define MTDIDS_DEFAULT "nor0=ml507-flash" #define MTDPARTS_DEFAULT "mtdparts=ml507-flash:-(user)" +/*Generic Configs*/ +#include #endif /* __CONFIG_H */ diff --git a/include/configs/v5fx30teval.h b/include/configs/v5fx30teval.h new file mode 100644 index 0000000..67d8d7f --- /dev/null +++ b/include/configs/v5fx30teval.h @@ -0,0 +1,49 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*CPU*/ +#define CONFIG_440 1 +#define CONFIG_XILINX_ML507 1 +#include "../board/avnet/v5fx30teval/xparameters.h" + +/*Mem Map*/ +#define CFG_SDRAM_SIZE_MB 64 + +/*Env*/ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x20000 +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_OFFSET 0x1A0000 +#define CFG_ENV_ADDR (XPAR_FLASH_MEM0_BASEADDR+CFG_ENV_OFFSET) + +/*Misc*/ +#define CFG_PROMPT "v5fx30t:/# " /* Monitor Command Prompt */ +#define CONFIG_PREBOOT "echo U-Boot is up and runnining;" + +/*Flash*/ +#define CFG_FLASH_SIZE (16*1024*1024) +#define CFG_MAX_FLASH_SECT 131 +#define MTDIDS_DEFAULT "nor0=v5fx30t-flash" +#define MTDPARTS_DEFAULT "mtdparts=v5fx30t-flash:-(user)" + +/*Generic Configs*/ +#include + +#endif /* __CONFIG_H */ diff --git a/include/configs/xilinx-ppc440-generic.h b/include/configs/xilinx-ppc440-generic.h new file mode 100644 index 0000000..4e8080b --- /dev/null +++ b/include/configs/xilinx-ppc440-generic.h @@ -0,0 +1,49 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*CPU*/ +#define CONFIG_440 1 +#define CONFIG_XILINX_PPC440_GENERIC 1 +#include "../board/xilinx/ppc440-generic/xparameters.h" + +/*Mem Map*/ +#define CFG_SDRAM_SIZE_MB 256 + +/*Env*/ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x20000 +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_OFFSET 0x340000 +#define CFG_ENV_ADDR (XPAR_FLASH_MEM0_BASEADDR+CFG_ENV_OFFSET) + +/*Misc*/ +#define CFG_PROMPT "board:/# " /* Monitor Command Prompt */ +#define CONFIG_PREBOOT "echo U-Boot is up and runnining;" + +/*Flash*/ +#define CFG_FLASH_SIZE (32*1024*1024) +#define CFG_MAX_FLASH_SECT 259 +#define MTDIDS_DEFAULT "nor0=ml507-flash" +#define MTDPARTS_DEFAULT "mtdparts=ml507-flash:-(user)" + +/*Generic Configs*/ +#include + +#endif /* __CONFIG_H */ diff --git a/include/configs/xilinx-ppc440.h b/include/configs/xilinx-ppc440.h new file mode 100644 index 0000000..40293cd --- /dev/null +++ b/include/configs/xilinx-ppc440.h @@ -0,0 +1,106 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . +*/ + +#ifndef __CONFIG_GEN_H +#define __CONFIG_GEN_H +/* +#define DEBUG +#define ET_DEBUG +*/ + /*CPU*/ +#define CONFIG_XILINX_440 1 +#define CONFIG_440 1 +#define CONFIG_4xx 1 + +/*Mem Map*/ +#define CFG_SDRAM_BASE 0x0 +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (192 * 1024) +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128 * 1024) + +/*Uart*/ +#define CONFIG_XILINX_UARTLITE +#define CONFIG_BAUDRATE XPAR_UARTLITE_0_BAUDRATE +#define CFG_BAUDRATE_TABLE { XPAR_UARTLITE_0_BAUDRATE } +#define CONFIG_SERIAL_BASE XPAR_UARTLITE_0_BASEADDR + +/*Cmd*/ +#include +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_JFFS2 +#define CONFIG_JFFS2_CMDLINE +#undef CONFIG_CMD_SPI +#undef CONFIG_CMD_I2C +#undef CONFIG_CMD_DTT +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_PING +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_EEPROM +#undef CONFIG_CMD_IMLS + +/*Misc*/ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CFG_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ +#define CFG_LOAD_ADDR 0x00400000 /* default load address */ +#define CFG_EXTBDINFO 1 /* Extended board_into (bd_t) */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_CMDLINE_EDITING /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_LOOPW /* enable loopw command */ +#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE /* include version env variable */ +#define CFG_CONSOLE_INFO_QUIET /* don't print console @ startup */ +#define CFG_HUSH_PARSER /* Use the HUSH parser */ +#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ +#define CFG_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */ + +/*Stack*/ +#define CFG_INIT_RAM_ADDR 0x800000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +/*Speed*/ +#define CONFIG_SYS_CLK_FREQ XPAR_CORE_CLOCK_FREQ_HZ + +/*Flash*/ +#define CFG_FLASH_BASE XPAR_FLASH_MEM0_BASEADDR +#define CFG_FLASH_CFI 1 +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CFG_FLASH_EMPTY_INFO 1 +#define CFG_MAX_FLASH_BANKS 1 +#define CFG_FLASH_PROTECTION + +#endif /* __CONFIG_H */ -- cgit v0.10.2 From 075d0b81e896e8735ae26372cd384f87cbd24e41 Mon Sep 17 00:00:00 2001 From: Adam Graham Date: Wed, 3 Sep 2008 12:26:28 -0700 Subject: ppc4xx: IBM Memory Controller DDR autocalibration routines Alternate SDRAM DDR autocalibration routine that can be generically used for any PPC4xx chips that have the IBM SDRAM Controller core allowing for support of more DIMM/memory chip vendors and gets the DDR autocalibration values which give the best read latency performance (SDRAM0_RDCC.[RDSS]). Two alternate SDRAM DDR autocalibration algoritm are provided in this patch, "Method_A" and "Method_B". DDR autocalibration Method_A scans the full range of possible PPC4xx SDRAM Controller DDR autocalibration values and takes a lot longer to run than Method_B. Method_B executes in the same amount of time as the currently existing DDR autocalibration routine, i.e. 1 second or so. Normally Method_B is used and it is set as the default method. The current U-Boot PPC4xx DDR autocalibration code calibrates the IBM SDRAM Controller registers.[bit-field]: 1) SDRAM0_RQDC.[RQFD] 2) SDRAM0_RFDC.[RFFD] This alternate PPC4xx DDR autocalibration code calibrates the following IBM SDRAM Controller registers.[bit-field]: 1) SDRAM0_WRDTR.[WDTR] 2) SDRAM0_CLKTR.[CKTR] 3) SDRAM0_RQDC.[RQFD] 4) SDRAM0_RFDC.[RFFD] and will also use the calibrated settings of the above four registers that produce the best "Read Sample Cycle Select" value in the SDRAM0_RDCC.[RDSS] register.[bit-field]. Signed-off-by: Adam Graham Signed-off-by: Stefan Roese diff --git a/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c b/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c new file mode 100644 index 0000000..83b9883 --- /dev/null +++ b/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c @@ -0,0 +1,1212 @@ +/* + * cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c + * This SPD SDRAM detection code supports AMCC PPC44x cpu's with a + * DDR2 controller (non Denali Core). Those currently are: + * + * 405: 405EX + * 440/460: 440SP/440SPe/460EX/460GT/460SX + * + * (C) Copyright 2008 Applied Micro Circuits Corporation + * Adam Graham + * + * (C) Copyright 2007-2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * COPYRIGHT AMCC CORPORATION 2004 + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* define DEBUG for debugging output (obviously ;-)) */ +#undef DEBUG + +#include +#include +#include +#include + +#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) + +/* + * Only compile the DDR auto-calibration code for NOR boot and + * not for NAND boot (NAND SPL and NAND U-Boot - NUB) + */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) + +#define MAXBXCF 4 +#define SDRAM_RXBAS_SHIFT_1M 20 + +#if defined(CFG_DECREMENT_PATTERNS) +#define NUMMEMTESTS 24 +#else +#define NUMMEMTESTS 8 +#endif /* CFG_DECREMENT_PATTERNS */ +#define NUMLOOPS 1 /* configure as you deem approporiate */ +#define NUMMEMWORDS 16 + +/* Private Structure Definitions */ + +struct autocal_regs { + u32 rffd; + u32 rqfd; +}; + +struct ddrautocal { + u32 rffd; + u32 rffd_min; + u32 rffd_max; + u32 rffd_size; + u32 rqfd; + u32 rqfd_size; + u32 rdcc; + u32 flags; +}; + +struct sdram_timing { + u32 wrdtr; + u32 clktr; +}; + +struct sdram_timing_clks { + u32 wrdtr; + u32 clktr; + u32 rdcc; + u32 flags; +}; + +struct autocal_clks { + struct sdram_timing_clks clocks; + struct ddrautocal autocal; +}; + +/*--------------------------------------------------------------------------+ + * Prototypes + *--------------------------------------------------------------------------*/ +#if defined(CONFIG_PPC4xx_DDR_METHOD_A) +static u32 DQS_calibration_methodA(struct ddrautocal *); +static u32 program_DQS_calibration_methodA(struct ddrautocal *); +#else +static u32 DQS_calibration_methodB(struct ddrautocal *); +static u32 program_DQS_calibration_methodB(struct ddrautocal *); +#endif +static int short_mem_test(u32 *); + +/* + * To provide an interface for board specific config values in this common + * DDR setup code, we implement he "weak" default functions here. They return + * the default value back to the caller. + * + * Please see include/configs/yucca.h for an example fora board specific + * implementation. + */ + +#if !defined(CONFIG_SPD_EEPROM) +u32 __ddr_wrdtr(u32 default_val) +{ + return default_val; +} +u32 ddr_wrdtr(u32) __attribute__((weak, alias("__ddr_wrdtr"))); + +u32 __ddr_clktr(u32 default_val) +{ + return default_val; +} +u32 ddr_clktr(u32) __attribute__((weak, alias("__ddr_clktr"))); + +/* + * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed + */ +void __spd_ddr_init_hang(void) +{ + hang(); +} +void +spd_ddr_init_hang(void) __attribute__((weak, alias("__spd_ddr_init_hang"))); +#endif /* defined(CONFIG_SPD_EEPROM) */ + +ulong __ddr_scan_option(ulong default_val) +{ + return default_val; +} +ulong ddr_scan_option(ulong) __attribute__((weak, alias("__ddr_scan_option"))); + +static u32 *get_membase(int bxcr_num) +{ + ulong bxcf; + u32 *membase; + +#if defined(SDRAM_R0BAS) + /* BAS from Memory Queue rank reg. */ + membase = + (u32 *)(SDRAM_RXBAS_SDBA_DECODE(mfdcr_any(SDRAM_R0BAS+bxcr_num))); + bxcf = 0; /* just to satisfy the compiler */ +#else + /* BAS from SDRAM_MBxCF mem rank reg. */ + mfsdram(SDRAM_MB0CF + (bxcr_num<<2), bxcf); + membase = (u32 *)((bxcf & 0xfff80000) << 3); +#endif + + return membase; +} + +static inline void ecc_clear_status_reg(void) +{ + mtsdram(SDRAM_ECCCR, 0xffffffff); +#if defined(SDRAM_R0BAS) + mtdcr(SDRAM_ERRSTATLL, 0xffffffff); +#endif +} + +static int ecc_check_status_reg(void) +{ + u32 ecc_status; + + /* + * Compare suceeded, now check + * if got ecc error. If got an + * ecc error, then don't count + * this as a passing value + */ + mfsdram(SDRAM_ECCCR, ecc_status); + if (ecc_status != 0x00000000) { + /* clear on error */ + ecc_clear_status_reg(); + /* ecc check failure */ + return 0; + } + ecc_clear_status_reg(); + sync(); + + return 1; +} + +/* return 1 if passes, 0 if fail */ +static int short_mem_test(u32 *base_address) +{ + int i, j, l; + u32 ecc_mode = 0; + + ulong test[NUMMEMTESTS][NUMMEMWORDS] = { + /* 0 */ {0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, + 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, + 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, + 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF}, + /* 1 */ {0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, + 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, + 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, + 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000}, + /* 2 */ {0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, + 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, + 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, + 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555}, + /* 3 */ {0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, + 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, + 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, + 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA}, + /* 4 */ {0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, + 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, + 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, + 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A}, + /* 5 */ {0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, + 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, + 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, + 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5}, + /* 6 */ {0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, + 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, + 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, + 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA}, + /* 7 */ {0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, + 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, + 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, + 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55}, + +#if defined(CFG_DECREMENT_PATTERNS) + /* 8 */ {0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, + 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, + 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, + 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff}, + /* 9 */ {0xfffefffe, 0xfffefffe, 0xfffefffe, 0xfffefffe, + 0xfffefffe, 0xfffefffe, 0xfffefffe, 0xfffefffe, + 0xfffefffe, 0xfffefffe, 0xfffefffe, 0xfffefffe, + 0xfffefffe, 0xfffefffe, 0xfffefffe, 0xfffefffe}, + /* 10 */{0xfffdfffd, 0xfffdfffd, 0xfffdffff, 0xfffdfffd, + 0xfffdfffd, 0xfffdfffd, 0xfffdffff, 0xfffdfffd, + 0xfffdfffd, 0xfffdfffd, 0xfffdffff, 0xfffdfffd, + 0xfffdfffd, 0xfffdfffd, 0xfffdffff, 0xfffdfffd}, + /* 11 */{0xfffcfffc, 0xfffcfffc, 0xfffcfffc, 0xfffcfffc, + 0xfffcfffc, 0xfffcfffc, 0xfffcfffc, 0xfffcfffc, + 0xfffcfffc, 0xfffcfffc, 0xfffcfffc, 0xfffcfffc, + 0xfffcfffc, 0xfffcfffc, 0xfffcfffc, 0xfffcfffc}, + /* 12 */{0xfffbfffb, 0xfffffffb, 0xfffffffb, 0xfffffffb, + 0xfffbfffb, 0xfffffffb, 0xfffffffb, 0xfffffffb, + 0xfffbfffb, 0xfffffffb, 0xfffffffb, 0xfffffffb, + 0xfffbfffb, 0xfffffffb, 0xfffffffb, 0xfffffffb}, + /* 13 */{0xfffafffa, 0xfffafffa, 0xfffffffa, 0xfffafffa, + 0xfffafffa, 0xfffafffa, 0xfffafffa, 0xfffafffa, + 0xfffafffa, 0xfffafffa, 0xfffafffa, 0xfffafffa, + 0xfffafffa, 0xfffafffa, 0xfffafffa, 0xfffafffa}, + /* 14 */{0xfff9fff9, 0xfff9fff9, 0xfff9fff9, 0xfff9fff9, + 0xfff9fff9, 0xfff9fff9, 0xfff9fff9, 0xfff9fff9, + 0xfff9fff9, 0xfff9fff9, 0xfff9fff9, 0xfff9fff9, + 0xfff9fff9, 0xfff9fff9, 0xfff9fff9, 0xfff9fff9}, + /* 15 */{0xfff8fff8, 0xfff8fff8, 0xfff8fff8, 0xfff8fff8, + 0xfff8fff8, 0xfff8fff8, 0xfff8fff8, 0xfff8fff8, + 0xfff8fff8, 0xfff8fff8, 0xfff8fff8, 0xfff8fff8, + 0xfff8fff8, 0xfff8fff8, 0xfff8fff8, 0xfff8fff8}, + /* 16 */{0xfff7fff7, 0xfff7ffff, 0xfff7fff7, 0xfff7fff7, + 0xfff7fff7, 0xfff7ffff, 0xfff7fff7, 0xfff7fff7, + 0xfff7fff7, 0xfff7ffff, 0xfff7fff7, 0xfff7fff7, + 0xfff7ffff, 0xfff7ffff, 0xfff7fff7, 0xfff7fff7}, + /* 17 */{0xfff6fff5, 0xfff6ffff, 0xfff6fff6, 0xfff6fff7, + 0xfff6fff5, 0xfff6ffff, 0xfff6fff6, 0xfff6fff7, + 0xfff6fff5, 0xfff6ffff, 0xfff6fff6, 0xfff6fff7, + 0xfff6fff5, 0xfff6ffff, 0xfff6fff6, 0xfff6fff7}, + /* 18 */{0xfff5fff4, 0xfff5ffff, 0xfff5fff5, 0xfff5fff5, + 0xfff5fff4, 0xfff5ffff, 0xfff5fff5, 0xfff5fff5, + 0xfff5fff4, 0xfff5ffff, 0xfff5fff5, 0xfff5fff5, + 0xfff5fff4, 0xfff5ffff, 0xfff5fff5, 0xfff5fff5}, + /* 19 */{0xfff4fff3, 0xfff4ffff, 0xfff4fff4, 0xfff4fff4, + 0xfff4fff3, 0xfff4ffff, 0xfff4fff4, 0xfff4fff4, + 0xfff4fff3, 0xfff4ffff, 0xfff4fff4, 0xfff4fff4, + 0xfff4fff3, 0xfff4ffff, 0xfff4fff4, 0xfff4fff4}, + /* 20 */{0xfff3fff2, 0xfff3ffff, 0xfff3fff3, 0xfff3fff3, + 0xfff3fff2, 0xfff3ffff, 0xfff3fff3, 0xfff3fff3, + 0xfff3fff2, 0xfff3ffff, 0xfff3fff3, 0xfff3fff3, + 0xfff3fff2, 0xfff3ffff, 0xfff3fff3, 0xfff3fff3}, + /* 21 */{0xfff2ffff, 0xfff2ffff, 0xfff2fff2, 0xfff2fff2, + 0xfff2ffff, 0xfff2ffff, 0xfff2fff2, 0xfff2fff2, + 0xfff2ffff, 0xfff2ffff, 0xfff2fff2, 0xfff2fff2, + 0xfff2ffff, 0xfff2ffff, 0xfff2fff2, 0xfff2fff2}, + /* 22 */{0xfff1ffff, 0xfff1ffff, 0xfff1fff1, 0xfff1fff1, + 0xfff1ffff, 0xfff1ffff, 0xfff1fff1, 0xfff1fff1, + 0xfff1ffff, 0xfff1ffff, 0xfff1fff1, 0xfff1fff1, + 0xfff1ffff, 0xfff1ffff, 0xfff1fff1, 0xfff1fff1}, + /* 23 */{0xfff0fff0, 0xfff0fff0, 0xfff0fff0, 0xfff0fff0, + 0xfff0fff0, 0xfff0fff0, 0xfff0fff0, 0xfff0fff0, + 0xfff0fff0, 0xfff0fff0, 0xfff0fff0, 0xfff0fff0, + 0xfff0fff0, 0xfff0fffe, 0xfff0fff0, 0xfff0fff0}, +#endif /* CFG_DECREMENT_PATTERNS */ + }; + + mfsdram(SDRAM_MCOPT1, ecc_mode); + if ((ecc_mode & SDRAM_MCOPT1_MCHK_CHK_REP) == + SDRAM_MCOPT1_MCHK_CHK_REP) { + ecc_clear_status_reg(); + sync(); + ecc_mode = 1; + } else { + ecc_mode = 0; + } + + /* + * Run the short memory test. + */ + for (i = 0; i < NUMMEMTESTS; i++) { + for (j = 0; j < NUMMEMWORDS; j++) { + base_address[j] = test[i][j]; + ppcDcbf((ulong)&(base_address[j])); + } + sync(); + for (l = 0; l < NUMLOOPS; l++) { + for (j = 0; j < NUMMEMWORDS; j++) { + if (base_address[j] != test[i][j]) { + ppcDcbf((u32)&(base_address[j])); + return 0; + } else { + if (ecc_mode) { + if (!ecc_check_status_reg()) + return 0; + } + } + ppcDcbf((u32)&(base_address[j])); + } /* for (j = 0; j < NUMMEMWORDS; j++) */ + sync(); + } /* for (l=0; lSDRAM_RDCC=0x%08x\n", __func__, temp); +#endif + + pass_result = DQS_calibration_methodA(ddrcal); + + return pass_result; +} + +/* + * DQS_calibration_methodA() + * + * Autocalibration Method A + * + * ARRAY [Entire DQS Range] DQS_Valid_Window ; initialized to all zeros + * ARRAY [Entire FDBK Range] FDBK_Valid_Window; initialized to all zeros + * MEMWRITE(addr, expected_data); + * for (i = 0; i < Entire DQS Range; i++) { RQDC.RQFD + * for (j = 0; j < Entire FDBK Range; j++) { RFDC.RFFD + * MEMREAD(addr, actual_data); + * if (actual_data == expected_data) { + * DQS_Valid_Window[i] = 1; RQDC.RQFD + * FDBK_Valid_Window[i][j] = 1; RFDC.RFFD + * } + * } + * } + */ +static u32 DQS_calibration_methodA(struct ddrautocal *cal) +{ + ulong rfdc_reg; + ulong rffd; + + ulong rqdc_reg; + ulong rqfd; + + u32 *membase; + ulong bxcf; + int rqfd_average; + int bxcr_num; + int rffd_average; + int pass; + u32 passed = 0; + + int in_window; + struct autocal_regs curr_win_min; + struct autocal_regs curr_win_max; + struct autocal_regs best_win_min; + struct autocal_regs best_win_max; + struct autocal_regs loop_win_min; + struct autocal_regs loop_win_max; + +#ifdef DEBUG + ulong temp; +#endif + ulong rdcc; + + char slash[] = "\\|/-\\|/-"; + int loopi = 0; + + /* start */ + in_window = 0; + + memset(&curr_win_min, 0, sizeof(curr_win_min)); + memset(&curr_win_max, 0, sizeof(curr_win_max)); + memset(&best_win_min, 0, sizeof(best_win_min)); + memset(&best_win_max, 0, sizeof(best_win_max)); + memset(&loop_win_min, 0, sizeof(loop_win_min)); + memset(&loop_win_max, 0, sizeof(loop_win_max)); + + rdcc = 0; + + /* + * Program RDCC register + * Read sample cycle auto-update enable + */ + mtsdram(SDRAM_RDCC, SDRAM_RDCC_RDSS_T1 | SDRAM_RDCC_RSAE_ENABLE); + +#ifdef DEBUG + mfsdram(SDRAM_RDCC, temp); + debug("<%s>SDRAM_RDCC=0x%x\n", __func__, temp); + mfsdram(SDRAM_RTSR, temp); + debug("<%s>SDRAM_RTSR=0x%x\n", __func__, temp); + mfsdram(SDRAM_FCSR, temp); + debug("<%s>SDRAM_FCSR=0x%x\n", __func__, temp); +#endif + + /* + * Program RQDC register + * Internal DQS delay mechanism enable + */ + mtsdram(SDRAM_RQDC, + SDRAM_RQDC_RQDE_ENABLE | SDRAM_RQDC_RQFD_ENCODE(0x00)); + +#ifdef DEBUG + mfsdram(SDRAM_RQDC, temp); + debug("<%s>SDRAM_RQDC=0x%x\n", __func__, temp); +#endif + + /* + * Program RFDC register + * Set Feedback Fractional Oversample + * Auto-detect read sample cycle enable + */ + mtsdram(SDRAM_RFDC, SDRAM_RFDC_ARSE_ENABLE | + SDRAM_RFDC_RFOS_ENCODE(0) | SDRAM_RFDC_RFFD_ENCODE(0)); + +#ifdef DEBUG + mfsdram(SDRAM_RFDC, temp); + debug("<%s>SDRAM_RFDC=0x%x\n", __func__, temp); +#endif + + putc(' '); + for (rqfd = 0; rqfd <= SDRAM_RQDC_RQFD_MAX; rqfd++) { + + mfsdram(SDRAM_RQDC, rqdc_reg); + rqdc_reg &= ~(SDRAM_RQDC_RQFD_MASK); + mtsdram(SDRAM_RQDC, rqdc_reg | SDRAM_RQDC_RQFD_ENCODE(rqfd)); + + putc('\b'); + putc(slash[loopi++ % 8]); + + curr_win_min.rffd = 0; + curr_win_max.rffd = 0; + in_window = 0; + + for (rffd = 0, pass = 0; rffd <= SDRAM_RFDC_RFFD_MAX; rffd++) { + mfsdram(SDRAM_RFDC, rfdc_reg); + rfdc_reg &= ~(SDRAM_RFDC_RFFD_MASK); + mtsdram(SDRAM_RFDC, + rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd)); + + for (bxcr_num = 0; bxcr_num < MAXBXCF; bxcr_num++) { + mfsdram(SDRAM_MB0CF + (bxcr_num<<2), bxcf); + + /* Banks enabled */ + if (bxcf & SDRAM_BXCF_M_BE_MASK) { + /* Bank is enabled */ + membase = get_membase(bxcr_num); + pass = short_mem_test(membase); + } /* if bank enabled */ + } /* for bxcr_num */ + + /* If this value passed update RFFD windows */ + if (pass && !in_window) { /* at the start of window */ + in_window = 1; + curr_win_min.rffd = curr_win_max.rffd = rffd; + curr_win_min.rqfd = curr_win_max.rqfd = rqfd; + mfsdram(SDRAM_RDCC, rdcc); /*record this value*/ + } else if (!pass && in_window) { /* at end of window */ + in_window = 0; + } else if (pass && in_window) { /* within the window */ + curr_win_max.rffd = rffd; + curr_win_max.rqfd = rqfd; + } + /* else if (!pass && !in_window) + skip - no pass, not currently in a window */ + + if (in_window) { + if ((curr_win_max.rffd - curr_win_min.rffd) > + (best_win_max.rffd - best_win_min.rffd)) { + best_win_min.rffd = curr_win_min.rffd; + best_win_max.rffd = curr_win_max.rffd; + + best_win_min.rqfd = curr_win_min.rqfd; + best_win_max.rqfd = curr_win_max.rqfd; + cal->rdcc = rdcc; + } + passed = 1; + } + } /* RFDC.RFFD */ + + /* + * save-off the best window results of the RFDC.RFFD + * for this RQDC.RQFD setting + */ + /* + * if (just ended RFDC.RFDC loop pass window) > + * (prior RFDC.RFFD loop pass window) + */ + if ((best_win_max.rffd - best_win_min.rffd) > + (loop_win_max.rffd - loop_win_min.rffd)) { + loop_win_min.rffd = best_win_min.rffd; + loop_win_max.rffd = best_win_max.rffd; + loop_win_min.rqfd = rqfd; + loop_win_max.rqfd = rqfd; + debug("RQFD.min 0x%08x, RQFD.max 0x%08x, " + "RFFD.min 0x%08x, RFFD.max 0x%08x\n", + loop_win_min.rqfd, loop_win_max.rqfd, + loop_win_min.rffd, loop_win_max.rffd); + } + } /* RQDC.RQFD */ + + putc('\b'); + + debug("\n"); + + if ((loop_win_min.rffd == 0) && (loop_win_max.rffd == 0) && + (best_win_min.rffd == 0) && (best_win_max.rffd == 0) && + (best_win_min.rqfd == 0) && (best_win_max.rqfd == 0)) { + passed = 0; + } + + /* + * Need to program RQDC before RFDC. + */ + debug("<%s> RQFD Min: 0x%x\n", __func__, loop_win_min.rqfd); + debug("<%s> RQFD Max: 0x%x\n", __func__, loop_win_max.rqfd); + rqfd_average = loop_win_max.rqfd; + + if (rqfd_average < 0) + rqfd_average = 0; + + if (rqfd_average > SDRAM_RQDC_RQFD_MAX) + rqfd_average = SDRAM_RQDC_RQFD_MAX; + + debug("<%s> RFFD average: 0x%08x\n", __func__, rqfd_average); + mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) | + SDRAM_RQDC_RQFD_ENCODE(rqfd_average)); + + debug("<%s> RFFD Min: 0x%08x\n", __func__, loop_win_min.rffd); + debug("<%s> RFFD Max: 0x%08x\n", __func__, loop_win_max.rffd); + rffd_average = ((loop_win_min.rffd + loop_win_max.rffd) / 2); + + if (rffd_average < 0) + rffd_average = 0; + + if (rffd_average > SDRAM_RFDC_RFFD_MAX) + rffd_average = SDRAM_RFDC_RFFD_MAX; + + debug("<%s> RFFD average: 0x%08x\n", __func__, rffd_average); + mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd_average)); + + /* if something passed, then return the size of the largest window */ + if (passed != 0) { + passed = loop_win_max.rffd - loop_win_min.rffd; + cal->rqfd = rqfd_average; + cal->rffd = rffd_average; + cal->rffd_min = loop_win_min.rffd; + cal->rffd_max = loop_win_max.rffd; + } + + return (u32)passed; +} + +#else /* !defined(CONFIG_PPC4xx_DDR_METHOD_A) */ + +/*-----------------------------------------------------------------------------+ +| program_DQS_calibration_methodB. ++-----------------------------------------------------------------------------*/ +static u32 program_DQS_calibration_methodB(struct ddrautocal *ddrcal) +{ + u32 pass_result = 0; + +#ifdef DEBUG + ulong temp; +#endif + + /* + * Program RDCC register + * Read sample cycle auto-update enable + */ + mtsdram(SDRAM_RDCC, SDRAM_RDCC_RDSS_T2 | SDRAM_RDCC_RSAE_ENABLE); + +#ifdef DEBUG + mfsdram(SDRAM_RDCC, temp); + debug("<%s>SDRAM_RDCC=0x%08x\n", __func__, temp); +#endif + + /* + * Program RQDC register + * Internal DQS delay mechanism enable + */ + mtsdram(SDRAM_RQDC, +#if defined(CONFIG_DDR_RQDC_START_VAL) + SDRAM_RQDC_RQDE_ENABLE | + SDRAM_RQDC_RQFD_ENCODE(CONFIG_DDR_RQDC_START_VAL)); +#else + SDRAM_RQDC_RQDE_ENABLE | SDRAM_RQDC_RQFD_ENCODE(0x38)); +#endif + +#ifdef DEBUG + mfsdram(SDRAM_RQDC, temp); + debug("<%s>SDRAM_RQDC=0x%08x\n", __func__, temp); +#endif + + /* + * Program RFDC register + * Set Feedback Fractional Oversample + * Auto-detect read sample cycle enable + */ + mtsdram(SDRAM_RFDC, SDRAM_RFDC_ARSE_ENABLE | + SDRAM_RFDC_RFOS_ENCODE(0) | + SDRAM_RFDC_RFFD_ENCODE(0)); + +#ifdef DEBUG + mfsdram(SDRAM_RFDC, temp); + debug("<%s>SDRAM_RFDC=0x%08x\n", __func__, temp); +#endif + + pass_result = DQS_calibration_methodB(ddrcal); + + return pass_result; +} + +/* + * DQS_calibration_methodB() + * + * Autocalibration Method B + * + * ARRAY [Entire DQS Range] DQS_Valid_Window ; initialized to all zeros + * ARRAY [Entire Feedback Range] FDBK_Valid_Window; initialized to all zeros + * MEMWRITE(addr, expected_data); + * Initialialize the DQS delay to 80 degrees (MCIF0_RRQDC[RQFD]=0x38). + * + * for (j = 0; j < Entire Feedback Range; j++) { + * MEMREAD(addr, actual_data); + * if (actual_data == expected_data) { + * FDBK_Valid_Window[j] = 1; + * } + * } + * + * Set MCIF0_RFDC[RFFD] to the middle of the FDBK_Valid_Window. + * + * for (i = 0; i < Entire DQS Range; i++) { + * MEMREAD(addr, actual_data); + * if (actual_data == expected_data) { + * DQS_Valid_Window[i] = 1; + * } + * } + * + * Set MCIF0_RRQDC[RQFD] to the middle of the DQS_Valid_Window. + */ +/*-----------------------------------------------------------------------------+ +| DQS_calibration_methodB. ++-----------------------------------------------------------------------------*/ +static u32 DQS_calibration_methodB(struct ddrautocal *cal) +{ + ulong rfdc_reg; + ulong rffd; + + ulong rqdc_reg; + ulong rqfd; + + ulong rdcc; + + u32 *membase; + ulong bxcf; + int rqfd_average; + int bxcr_num; + int rffd_average; + int pass; + uint passed = 0; + + int in_window; + u32 curr_win_min, curr_win_max; + u32 best_win_min, best_win_max; + u32 size = 0; + + /*------------------------------------------------------------------ + | Test to determine the best read clock delay tuning bits. + | + | Before the DDR controller can be used, the read clock delay needs to + | be set. This is SDRAM_RQDC[RQFD] and SDRAM_RFDC[RFFD]. + | This value cannot be hardcoded into the program because it changes + | depending on the board's setup and environment. + | To do this, all delay values are tested to see if they + | work or not. By doing this, you get groups of fails with groups of + | passing values. The idea is to find the start and end of a passing + | window and take the center of it to use as the read clock delay. + | + | A failure has to be seen first so that when we hit a pass, we know + | that it is truely the start of the window. If we get passing values + | to start off with, we don't know if we are at the start of the window + | + | The code assumes that a failure will always be found. + | If a failure is not found, there is no easy way to get the middle + | of the passing window. I guess we can pretty much pick any value + | but some values will be better than others. Since the lowest speed + | we can clock the DDR interface at is 200 MHz (2x 100 MHz PLB speed), + | from experimentation it is safe to say you will always have a failure + +-----------------------------------------------------------------*/ + + debug("\n\n"); + + in_window = 0; + rdcc = 0; + + curr_win_min = curr_win_max = 0; + best_win_min = best_win_max = 0; + for (rffd = 0; rffd <= SDRAM_RFDC_RFFD_MAX; rffd++) { + mfsdram(SDRAM_RFDC, rfdc_reg); + rfdc_reg &= ~(SDRAM_RFDC_RFFD_MASK); + mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd)); + + pass = 1; + for (bxcr_num = 0; bxcr_num < MAXBXCF; bxcr_num++) { + mfsdram(SDRAM_MB0CF + (bxcr_num<<2), bxcf); + + /* Banks enabled */ + if (bxcf & SDRAM_BXCF_M_BE_MASK) { + /* Bank is enabled */ + membase = get_membase(bxcr_num); + pass &= short_mem_test(membase); + } /* if bank enabled */ + } /* for bxcf_num */ + + /* If this value passed */ + if (pass && !in_window) { /* start of passing window */ + in_window = 1; + curr_win_min = curr_win_max = rffd; + mfsdram(SDRAM_RDCC, rdcc); /* record this value */ + } else if (!pass && in_window) { /* end passing window */ + in_window = 0; + } else if (pass && in_window) { /* within the passing window */ + curr_win_max = rffd; + } + + if (in_window) { + if ((curr_win_max - curr_win_min) > + (best_win_max - best_win_min)) { + best_win_min = curr_win_min; + best_win_max = curr_win_max; + cal->rdcc = rdcc; + } + passed = 1; + } + } /* for rffd */ + + if ((best_win_min == 0) && (best_win_max == 0)) + passed = 0; + else + size = best_win_max - best_win_min; + + debug("RFFD Min: 0x%x\n", best_win_min); + debug("RFFD Max: 0x%x\n", best_win_max); + rffd_average = ((best_win_min + best_win_max) / 2); + + cal->rffd_min = best_win_min; + cal->rffd_max = best_win_max; + + if (rffd_average < 0) + rffd_average = 0; + + if (rffd_average > SDRAM_RFDC_RFFD_MAX) + rffd_average = SDRAM_RFDC_RFFD_MAX; + + mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd_average)); + + rffd = rffd_average; + in_window = 0; + + curr_win_min = curr_win_max = 0; + best_win_min = best_win_max = 0; + for (rqfd = 0; rqfd <= SDRAM_RQDC_RQFD_MAX; rqfd++) { + mfsdram(SDRAM_RQDC, rqdc_reg); + rqdc_reg &= ~(SDRAM_RQDC_RQFD_MASK); + mtsdram(SDRAM_RQDC, rqdc_reg | SDRAM_RQDC_RQFD_ENCODE(rqfd)); + + pass = 1; + for (bxcr_num = 0; bxcr_num < MAXBXCF; bxcr_num++) { + + mfsdram(SDRAM_MB0CF + (bxcr_num<<2), bxcf); + + /* Banks enabled */ + if (bxcf & SDRAM_BXCF_M_BE_MASK) { + /* Bank is enabled */ + membase = get_membase(bxcr_num); + pass &= short_mem_test(membase); + } /* if bank enabled */ + } /* for bxcf_num */ + + /* If this value passed */ + if (pass && !in_window) { + in_window = 1; + curr_win_min = curr_win_max = rqfd; + } else if (!pass && in_window) { + in_window = 0; + } else if (pass && in_window) { + curr_win_max = rqfd; + } + + if (in_window) { + if ((curr_win_max - curr_win_min) > + (best_win_max - best_win_min)) { + best_win_min = curr_win_min; + best_win_max = curr_win_max; + } + passed = 1; + } + } /* for rqfd */ + + if ((best_win_min == 0) && (best_win_max == 0)) + passed = 0; + + debug("RQFD Min: 0x%x\n", best_win_min); + debug("RQFD Max: 0x%x\n", best_win_max); + rqfd_average = ((best_win_min + best_win_max) / 2); + + if (rqfd_average < 0) + rqfd_average = 0; + + if (rqfd_average > SDRAM_RQDC_RQFD_MAX) + rqfd_average = SDRAM_RQDC_RQFD_MAX; + + mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) | + SDRAM_RQDC_RQFD_ENCODE(rqfd_average)); + + mfsdram(SDRAM_RQDC, rqdc_reg); + mfsdram(SDRAM_RFDC, rfdc_reg); + + /* + * Need to program RQDC before RFDC. The value is read above. + * That is the reason why auto cal not work. + * See, comments below. + */ + mtsdram(SDRAM_RQDC, rqdc_reg); + mtsdram(SDRAM_RFDC, rfdc_reg); + + debug("RQDC: 0x%08X\n", rqdc_reg); + debug("RFDC: 0x%08X\n", rfdc_reg); + + /* if something passed, then return the size of the largest window */ + if (passed != 0) { + passed = size; + cal->rqfd = rqfd_average; + cal->rffd = rffd_average; + } + + return (uint)passed; +} +#endif /* defined(CONFIG_PPC4xx_DDR_METHOD_A) */ + +/* + * Default table for DDR auto-calibration of all + * possible WRDTR and CLKTR values. + * Table format is: + * {SDRAM_WRDTR.[WDTR], SDRAM_CLKTR.[CKTR]} + * + * Table is terminated with {-1, -1} value pair. + * + * Board vendors can specify their own board specific subset of + * known working {SDRAM_WRDTR.[WDTR], SDRAM_CLKTR.[CKTR]} value + * pairs via a board defined ddr_scan_option() function. + */ +struct sdram_timing full_scan_options[] = { + {0, 0}, {0, 1}, {0, 2}, {0, 3}, + {1, 0}, {1, 1}, {1, 2}, {1, 3}, + {2, 0}, {2, 1}, {2, 2}, {2, 3}, + {3, 0}, {3, 1}, {3, 2}, {3, 3}, + {4, 0}, {4, 1}, {4, 2}, {4, 3}, + {5, 0}, {5, 1}, {5, 2}, {5, 3}, + {6, 0}, {6, 1}, {6, 2}, {6, 3}, + {-1, -1} +}; + +/*---------------------------------------------------------------------------+ +| DQS_calibration. ++----------------------------------------------------------------------------*/ +u32 DQS_autocalibration(void) +{ + u32 wdtr; + u32 clkp; + u32 result = 0; + u32 best_result = 0; + u32 best_rdcc; + struct ddrautocal ddrcal; + struct autocal_clks tcal; + ulong rfdc_reg; + ulong rqdc_reg; + u32 val; + int verbose_lvl = 0; + char *str; + char slash[] = "\\|/-\\|/-"; + int loopi = 0; + struct sdram_timing *scan_list; + +#if defined(DEBUG_PPC4xx_DDR_AUTOCALIBRATION) + int i; + char tmp[64]; /* long enough for environment variables */ +#endif + + memset(&tcal, 0, sizeof(tcal)); + + ddr_scan_option((ulong)full_scan_options); + + scan_list = + (struct sdram_timing *)ddr_scan_option((ulong)full_scan_options); + + mfsdram(SDRAM_MCOPT1, val); + if ((val & SDRAM_MCOPT1_MCHK_CHK_REP) == SDRAM_MCOPT1_MCHK_CHK_REP) + str = "ECC Auto calibration -"; + else + str = "Auto calibration -"; + + puts(str); + +#if defined(DEBUG_PPC4xx_DDR_AUTOCALIBRATION) + i = getenv_r("autocalib", tmp, sizeof(tmp)); + if (i < 0) + strcpy(tmp, CONFIG_AUTOCALIB); + + if (strcmp(tmp, "final") == 0) { + /* display the final autocalibration results only */ + verbose_lvl = 1; + } else if (strcmp(tmp, "loop") == 0) { + /* display summary autocalibration info per iteration */ + verbose_lvl = 2; + } else if (strcmp(tmp, "display") == 0) { + /* display full debug autocalibration window info. */ + verbose_lvl = 3; + } +#endif /* (DEBUG_PPC4xx_DDR_AUTOCALIBRATION) */ + + best_rdcc = (SDRAM_RDCC_RDSS_T4 >> 30); + + while ((scan_list->wrdtr != -1) && (scan_list->clktr != -1)) { + wdtr = scan_list->wrdtr; + clkp = scan_list->clktr; + + mfsdram(SDRAM_WRDTR, val); + val &= ~(SDRAM_WRDTR_LLWP_MASK | SDRAM_WRDTR_WTR_MASK); + mtsdram(SDRAM_WRDTR, (val | + ddr_wrdtr(SDRAM_WRDTR_LLWP_1_CYC | (wdtr << 25)))); + + mtsdram(SDRAM_CLKTR, clkp << 30); + + putc('\b'); + putc(slash[loopi++ % 8]); + +#ifdef DEBUG + debug("\n"); + debug("*** --------------\n"); + mfsdram(SDRAM_WRDTR, val); + debug("*** SDRAM_WRDTR set to 0x%08x\n", val); + mfsdram(SDRAM_CLKTR, val); + debug("*** SDRAM_CLKTR set to 0x%08x\n", val); +#endif + + debug("\n"); + if (verbose_lvl > 2) { + printf("*** SDRAM_WRDTR (wdtr) set to %d\n", wdtr); + printf("*** SDRAM_CLKTR (clkp) set to %d\n", clkp); + } + + memset(&ddrcal, 0, sizeof(ddrcal)); + + /* + * DQS calibration. + */ + /* + * program_DQS_calibration_method[A|B]() returns 0 if no + * passing RFDC.[RFFD] window is found or returns the size + * of the best passing window; in the case of a found passing + * window, the ddrcal will contain the values of the best + * window RQDC.[RQFD] and RFDC.[RFFD]. + */ + + /* + * Call PPC4xx SDRAM DDR autocalibration methodA or methodB. + * Default is methodB. + * Defined the autocalibration method in the board specific + * header file. + * Please see include/configs/kilauea.h for an example for + * a board specific implementation. + */ +#if defined(CONFIG_PPC4xx_DDR_METHOD_A) + result = program_DQS_calibration_methodA(&ddrcal); +#else + result = program_DQS_calibration_methodB(&ddrcal); +#endif + + sync(); + + /* + * Clear potential errors resulting from auto-calibration. + * If not done, then we could get an interrupt later on when + * exceptions are enabled. + */ + set_mcsr(get_mcsr()); + + val = ddrcal.rdcc; /* RDCC from the best passing window */ + + udelay(100); + + if (verbose_lvl > 1) { + char *tstr; + switch ((val >> 30)) { + case 0: + if (result != 0) + tstr = "T1"; + else + tstr = "N/A"; + break; + case 1: + tstr = "T2"; + break; + case 2: + tstr = "T3"; + break; + case 3: + tstr = "T4"; + break; + default: + tstr = "unknown"; + break; + } + printf("** WRDTR(%d) CLKTR(%d), Wind (%d), best (%d), " + "max-min(0x%04x)(0x%04x), RDCC: %s\n", + wdtr, clkp, result, best_result, + ddrcal.rffd_min, ddrcal.rffd_max, tstr); + } + + /* + * The DQS calibration "result" is either "0" + * if no passing window was found, or is the + * size of the RFFD passing window. + */ + if (result != 0) { + tcal.autocal.flags = 1; + debug("*** (%d)(%d) result passed window size: 0x%08x, " + "rqfd = 0x%08x, rffd = 0x%08x, rdcc = 0x%08x\n", + wdtr, clkp, result, ddrcal.rqfd, + ddrcal.rffd, ddrcal.rdcc); + /* + * Save the SDRAM_WRDTR and SDRAM_CLKTR + * settings for the largest returned + * RFFD passing window size. + */ + if (result > best_result) { + /* + * want the lowest Read Sample Cycle Select + */ + val = (val & SDRAM_RDCC_RDSS_MASK) >> 30; + debug("*** (%d) (%d) current_rdcc, best_rdcc\n", + val, best_rdcc); + if (val <= best_rdcc) { + best_rdcc = val; + tcal.clocks.wrdtr = wdtr; + tcal.clocks.clktr = clkp; + tcal.clocks.rdcc = (val << 30); + tcal.autocal.rqfd = ddrcal.rqfd; + tcal.autocal.rffd = ddrcal.rffd; + best_result = result; + + if (verbose_lvl > 2) { + printf("** (%d)(%d) " + "best result: 0x%04x\n", + wdtr, clkp, + best_result); + printf("** (%d)(%d) " + "best WRDTR: 0x%04x\n", + wdtr, clkp, + tcal.clocks.wrdtr); + printf("** (%d)(%d) " + "best CLKTR: 0x%04x\n", + wdtr, clkp, + tcal.clocks.clktr); + printf("** (%d)(%d) " + "best RQDC: 0x%04x\n", + wdtr, clkp, + tcal.autocal.rqfd); + printf("** (%d)(%d) " + "best RFDC: 0x%04x\n", + wdtr, clkp, + tcal.autocal.rffd); + printf("** (%d)(%d) " + "best RDCC: 0x%08x\n", + wdtr, clkp, + (u32)tcal.clocks.rdcc); + mfsdram(SDRAM_RTSR, val); + printf("** (%d)(%d) best " + "loop RTSR: 0x%08x\n", + wdtr, clkp, val); + mfsdram(SDRAM_FCSR, val); + printf("** (%d)(%d) best " + "loop FCSR: 0x%08x\n", + wdtr, clkp, val); + } + } /* if (val <= best_rdcc) */ + } /* if (result >= best_result) */ + } /* if (result != 0) */ + scan_list++; + } /* while ((scan_list->wrdtr != -1) && (scan_list->clktr != -1)) */ + + if (tcal.autocal.flags == 1) { + if (verbose_lvl > 0) { + printf("*** --------------\n"); + printf("*** best_result window size: %d\n", + best_result); + printf("*** best_result WRDTR: 0x%04x\n", + tcal.clocks.wrdtr); + printf("*** best_result CLKTR: 0x%04x\n", + tcal.clocks.clktr); + printf("*** best_result RQFD: 0x%04x\n", + tcal.autocal.rqfd); + printf("*** best_result RFFD: 0x%04x\n", + tcal.autocal.rffd); + printf("*** best_result RDCC: 0x%04x\n", + tcal.clocks.rdcc); + printf("*** --------------\n"); + printf("\n"); + } + + /* + * if got best passing result window, then lock in the + * best CLKTR, WRDTR, RQFD, and RFFD values + */ + mfsdram(SDRAM_WRDTR, val); + mtsdram(SDRAM_WRDTR, (val & + ~(SDRAM_WRDTR_LLWP_MASK | SDRAM_WRDTR_WTR_MASK)) | + ddr_wrdtr(SDRAM_WRDTR_LLWP_1_CYC | + (tcal.clocks.wrdtr << 25))); + + mtsdram(SDRAM_CLKTR, tcal.clocks.clktr << 30); + + mfsdram(SDRAM_RQDC, rqdc_reg); + rqdc_reg &= ~(SDRAM_RQDC_RQFD_MASK); + mtsdram(SDRAM_RQDC, rqdc_reg | + SDRAM_RQDC_RQFD_ENCODE(tcal.autocal.rqfd)); + + mfsdram(SDRAM_RQDC, rqdc_reg); + debug("*** best_result: read value SDRAM_RQDC 0x%08x\n", + rqdc_reg); + + mfsdram(SDRAM_RFDC, rfdc_reg); + rfdc_reg &= ~(SDRAM_RFDC_RFFD_MASK); + mtsdram(SDRAM_RFDC, rfdc_reg | + SDRAM_RFDC_RFFD_ENCODE(tcal.autocal.rffd)); + + mfsdram(SDRAM_RFDC, rfdc_reg); + debug("*** best_result: read value SDRAM_RFDC 0x%08x\n", + rfdc_reg); + mfsdram(SDRAM_RDCC, val); + debug("*** SDRAM_RDCC 0x%08x\n", val); + } else { + /* + * no valid windows were found + */ + printf("DQS memory calibration window can not be determined, " + "terminating u-boot.\n"); + ppc4xx_ibm_ddr2_register_dump(); + spd_ddr_init_hang(); + } + + blank_string(strlen(str)); + + return 0; +} +#else /* defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ +u32 DQS_autocalibration(void) +{ + return 0; +} +#endif /* !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) */ +#endif /* defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) */ -- cgit v0.10.2 From f6b6c45840f9b4671d2d97243a12a1f3ffb64765 Mon Sep 17 00:00:00 2001 From: Adam Graham Date: Wed, 3 Sep 2008 12:26:59 -0700 Subject: ppc4xx: Update Kilauea to use PPC4xx DDR autocalibration routines Signed-off-by: Adam Graham Signed-off-by: Stefan Roese diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index 15250d4..f1d7684 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -60,8 +60,6 @@ "SDRAM_" #mnemonic, SDRAM_##mnemonic, data); \ } while (0) -static inline void ppc4xx_ibm_ddr2_register_dump(void); - #if defined(CONFIG_SPD_EEPROM) /*-----------------------------------------------------------------------------+ @@ -260,62 +258,19 @@ static void program_ecc_addr(unsigned long start_address, unsigned long num_bytes, unsigned long tlb_word2_i_value); #endif +#if !defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) static void program_DQS_calibration(unsigned long *dimm_populated, - unsigned char *iic0_dimm_addr, - unsigned long num_dimm_banks); + unsigned char *iic0_dimm_addr, + unsigned long num_dimm_banks); #ifdef HARD_CODED_DQS /* calibration test with hardvalues */ static void test(void); #else static void DQS_calibration_process(void); #endif +#endif int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); void dcbz_area(u32 start_address, u32 num_bytes); -static u32 mfdcr_any(u32 dcr) -{ - u32 val; - - switch (dcr) { - case SDRAM_R0BAS + 0: - val = mfdcr(SDRAM_R0BAS + 0); - break; - case SDRAM_R0BAS + 1: - val = mfdcr(SDRAM_R0BAS + 1); - break; - case SDRAM_R0BAS + 2: - val = mfdcr(SDRAM_R0BAS + 2); - break; - case SDRAM_R0BAS + 3: - val = mfdcr(SDRAM_R0BAS + 3); - break; - default: - printf("DCR %d not defined in case statement!!!\n", dcr); - val = 0; /* just to satisfy the compiler */ - } - - return val; -} - -static void mtdcr_any(u32 dcr, u32 val) -{ - switch (dcr) { - case SDRAM_R0BAS + 0: - mtdcr(SDRAM_R0BAS + 0, val); - break; - case SDRAM_R0BAS + 1: - mtdcr(SDRAM_R0BAS + 1, val); - break; - case SDRAM_R0BAS + 2: - mtdcr(SDRAM_R0BAS + 2, val); - break; - case SDRAM_R0BAS + 3: - mtdcr(SDRAM_R0BAS + 3, val); - break; - default: - printf("DCR %d not defined in case statement!!!\n", dcr); - } -} - static unsigned char spd_read(uchar chip, uint addr) { unsigned char data[2]; @@ -609,7 +564,11 @@ phys_size_t initdram(int board_type) /*------------------------------------------------------------------ * DQS calibration. *-----------------------------------------------------------------*/ +#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) + DQS_autocalibration(); +#else program_DQS_calibration(dimm_populated, iic0_dimm_addr, num_dimm_banks); +#endif #ifdef CONFIG_DDR_ECC /*------------------------------------------------------------------ @@ -2329,18 +2288,6 @@ static unsigned long is_ecc_enabled(void) return ecc; } -static void blank_string(int size) -{ - int i; - - for (i=0; i>2) +#if !defined(CONFIG_405EX) /* * Memory queue defines */ @@ -293,7 +295,6 @@ #define SDRAM_PLBADDUHB (SDRAMQ_DCR_BASE+0x10) /* PLB base address upper 32 LL */ -#if !defined(CONFIG_405EX) /* * Memory Bank 0-7 configuration */ diff --git a/include/common.h b/include/common.h index a394988..2516bfd 100644 --- a/include/common.h +++ b/include/common.h @@ -287,6 +287,27 @@ void pciinfo (int, int); #endif #endif +/* + * Prototypes + */ +#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) +void blank_string(int); +inline void ppc4xx_ibm_ddr2_register_dump(void); +#if defined(CONFIG_440) +u32 mfdcr_any(u32); +void mtdcr_any(u32, u32); +#endif +#if defined(CONFIG_SPD_EEPROM) +u32 ddr_wrdtr(u32); +u32 ddr_clktr(u32); +void spd_ddr_init_hang(void); +#endif +#endif /* defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) */ + +#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) +u32 DQS_autocalibration(void); +#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */ + int misc_init_f (void); int misc_init_r (void); diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index a475f97..f9eaa77 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -223,6 +223,22 @@ *----------------------------------------------------------------------*/ #define CFG_MBYTES_SDRAM (256) /* 256MB */ +/* + * CONFIG_PPC4xx_DDR_AUTOCALIBRATION + * + * Note: DDR Autocalibration Method_A scans the full range of possible PPC4xx + * SDRAM Controller DDR autocalibration values and takes a lot longer + * to run than Method_B. + * (See the Method_A and Method_B algorithm discription in the file: + * cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c) + * Define CONFIG_PPC4xx_DDR_METHOD_A to use DDR autocalibration Method_A + * + * DDR Autocalibration Method_B is the default. + */ +#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ +#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ +#undef CONFIG_PPC4xx_DDR_METHOD_A + #define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE) /* DDR1/2 SDRAM Device Control Register Data Values */ @@ -386,6 +402,9 @@ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 2 +/* Debug messages for the DDR autocalibration */ +#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ + /* * Default environment variables */ diff --git a/include/ppc440.h b/include/ppc440.h index 3584fd2..be8d3ff 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -2064,19 +2064,6 @@ #ifndef __ASSEMBLY__ -static inline u32 get_mcsr(void) -{ - u32 val; - - asm volatile("mfspr %0, 0x23c" : "=r" (val) :); - return val; -} - -static inline void set_mcsr(u32 val) -{ - asm volatile("mtspr 0x23c, %0" : "=r" (val) :); -} - #endif /* _ASMLANGUAGE */ #endif /* __PPC440_H__ */ diff --git a/include/ppc4xx.h b/include/ppc4xx.h index 59a3b06..e216663 100644 --- a/include/ppc4xx.h +++ b/include/ppc4xx.h @@ -203,6 +203,19 @@ typedef struct unsigned long pllPlbDiv; } PPC4xx_SYS_INFO; +static inline u32 get_mcsr(void) +{ + u32 val; + + asm volatile("mfspr %0, 0x23c" : "=r" (val) :); + return val; +} + +static inline void set_mcsr(u32 val) +{ + asm volatile("mtspr 0x23c, %0" : "=r" (val) :); +} + #endif /* __ASSEMBLY__ */ #endif /* __PPC4XX_H__ */ -- cgit v0.10.2 From 78d78236896d62bb8ca7302af38d8f1493eb2651 Mon Sep 17 00:00:00 2001 From: Victor Gallardo Date: Thu, 4 Sep 2008 23:49:36 -0700 Subject: ppc4xx: Add support for GPCS, SGMII and M88E1112 PHY This patch adds GPCS, SGMII and M88E1112 PHY support for the AMCC PPC460GT/EX processors. Signed-off-by: Victor Gallardo Signed-off-by: Stefan Roese diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 8a38335..071ac0a 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -198,6 +198,7 @@ #define BI_PHYMODE_RMII 8 #endif #endif +#define BI_PHYMODE_SGMII 9 #if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ @@ -216,6 +217,52 @@ #define MAL_RX_CHAN_MUL 1 #endif +/*--------------------------------------------------------------------+ + * Fixed PHY (PHY-less) support for Ethernet Ports. + *--------------------------------------------------------------------*/ + +/* + * Some boards do not have a PHY for each ethernet port. These ports + * are known as Fixed PHY (or PHY-less) ports. For such ports, set + * the appropriate CONFIG_PHY_ADDR equal to CONFIG_FIXED_PHY and + * then define CFG_FIXED_PHY_PORTS to define what the speed and + * duplex should be for these ports in the board configuration + * file. + * + * For Example: + * #define CONFIG_FIXED_PHY 0xFFFFFFFF + * + * #define CONFIG_PHY_ADDR CONFIG_FIXED_PHY + * #define CONFIG_PHY1_ADDR 1 + * #define CONFIG_PHY2_ADDR CONFIG_FIXED_PHY + * #define CONFIG_PHY3_ADDR 3 + * + * #define CFG_FIXED_PHY_PORT(devnum,speed,duplex) \ + * {devnum, speed, duplex}, + * + * #define CFG_FIXED_PHY_PORTS \ + * CFG_FIXED_PHY_PORT(0,1000,FULL) \ + * CFG_FIXED_PHY_PORT(2,100,HALF) + */ + +#ifndef CONFIG_FIXED_PHY +#define CONFIG_FIXED_PHY 0xFFFFFFFF /* Fixed PHY (PHY-less) */ +#endif + +#ifndef CFG_FIXED_PHY_PORTS +#define CFG_FIXED_PHY_PORTS /* default is an empty array */ +#endif + +struct fixed_phy_port { + unsigned int devnum; /* ethernet port */ + unsigned int speed; /* specified speed 10,100 or 1000 */ + unsigned int duplex; /* specified duplex FULL or HALF */ +}; + +static const struct fixed_phy_port fixed_phy_port[] = { + CFG_FIXED_PHY_PORTS /* defined in board configuration file */ +}; + /*-----------------------------------------------------------------------------+ * Global variables. TX and RX descriptors and buffers. *-----------------------------------------------------------------------------*/ @@ -611,8 +658,17 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) #if defined(CONFIG_460EX) mode = 9; + mfsdr(SDR0_ETH_CFG, eth_cfg); + if (((eth_cfg & SDR0_ETH_CFG_SGMII0_ENABLE) > 0) && + ((eth_cfg & SDR0_ETH_CFG_SGMII1_ENABLE) > 0)) + mode = 11; /* config SGMII */ #else mode = 10; + mfsdr(SDR0_ETH_CFG, eth_cfg); + if (((eth_cfg & SDR0_ETH_CFG_SGMII0_ENABLE) > 0) && + ((eth_cfg & SDR0_ETH_CFG_SGMII1_ENABLE) > 0) && + ((eth_cfg & SDR0_ETH_CFG_SGMII2_ENABLE) > 0)) + mode = 12; /* config SGMII */ #endif /* TODO: @@ -635,6 +691,8 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) /* * Right now only 2*RGMII is supported. Please extend when needed. * sr - 2008-02-19 + * Add SGMII support. + * vg - 2008-07-28 */ switch (mode) { case 1: @@ -761,6 +819,20 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) bis->bi_phymode[2] = BI_PHYMODE_RGMII; bis->bi_phymode[3] = BI_PHYMODE_RGMII; break; + case 11: + /* 2 SGMII - 460EX */ + bis->bi_phymode[0] = BI_PHYMODE_SGMII; + bis->bi_phymode[1] = BI_PHYMODE_SGMII; + bis->bi_phymode[2] = BI_PHYMODE_NONE; + bis->bi_phymode[3] = BI_PHYMODE_NONE; + break; + case 12: + /* 3 SGMII - 460GT */ + bis->bi_phymode[0] = BI_PHYMODE_SGMII; + bis->bi_phymode[1] = BI_PHYMODE_SGMII; + bis->bi_phymode[2] = BI_PHYMODE_SGMII; + bis->bi_phymode[3] = BI_PHYMODE_NONE; + break; default: break; } @@ -945,6 +1017,48 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg); #endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */ +#if defined(CONFIG_GPCS_PHY_ADDR) || defined(CONFIG_GPCS_PHY1_ADDR) || \ + defined(CONFIG_GPCS_PHY2_ADDR) || defined(CONFIG_GPCS_PHY3_ADDR) + if (bis->bi_phymode[devnum] == BI_PHYMODE_SGMII) { + /* + * In SGMII mode, GPCS access is needed for + * communication with the internal SGMII SerDes. + */ + switch (devnum) { +#if defined(CONFIG_GPCS_PHY_ADDR) + case 0: + reg = CONFIG_GPCS_PHY_ADDR; + break; +#endif +#if defined(CONFIG_GPCS_PHY1_ADDR) + case 1: + reg = CONFIG_GPCS_PHY1_ADDR; + break; +#endif +#if defined(CONFIG_GPCS_PHY2_ADDR) + case 2: + reg = CONFIG_GPCS_PHY2_ADDR; + break; +#endif +#if defined(CONFIG_GPCS_PHY3_ADDR) + case 3: + reg = CONFIG_GPCS_PHY3_ADDR; + break; +#endif + } + + mode_reg = in_be32((void *)EMAC_M1 + hw_p->hw_addr); + mode_reg |= EMAC_M1_MF_1000GPCS | EMAC_M1_IPPA_SET(reg); + out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg); + + /* Configure GPCS interface to recommended setting for SGMII */ + miiphy_reset(dev->name, reg); + miiphy_write(dev->name, reg, 0x04, 0x8120); /* AsymPause, FDX */ + miiphy_write(dev->name, reg, 0x07, 0x2801); /* msg_pg, toggle */ + miiphy_write(dev->name, reg, 0x00, 0x0140); /* 1Gbps, FDX */ + } +#endif /* defined(CONFIG_GPCS_PHY_ADDR) */ + /* wait for PHY to complete auto negotiation */ reg_short = 0; #ifndef CONFIG_CS8952_PHY @@ -974,6 +1088,9 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) bis->bi_phynum[devnum] = reg; + if (reg == CONFIG_FIXED_PHY) + goto get_speed; + #if defined(CONFIG_PHY_RESET) /* * Reset the phy, only if its the first time through @@ -986,6 +1103,27 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) miiphy_write (dev->name, reg, 0x09, 0x0e00); miiphy_write (dev->name, reg, 0x04, 0x01e1); #endif +#if defined(CONFIG_M88E1112_PHY) + if (bis->bi_phymode[devnum] == BI_PHYMODE_SGMII) { + /* + * Marvell 88E1112 PHY needs to have the SGMII MAC + * interace (page 2) properly configured to + * communicate with the 460EX/GT GPCS interface. + */ + + /* Set access to Page 2 */ + miiphy_write(dev->name, reg, 0x16, 0x0002); + + miiphy_write(dev->name, reg, 0x00, 0x0040); /* 1Gbps */ + miiphy_read(dev->name, reg, 0x1a, ®_short); + reg_short |= 0x8000; /* bypass Auto-Negotiation */ + miiphy_write(dev->name, reg, 0x1a, reg_short); + miiphy_reset(dev->name, reg); /* reset MAC interface */ + + /* Reset access to Page 0 */ + miiphy_write(dev->name, reg, 0x16, 0x0000); + } +#endif /* defined(CONFIG_M88E1112_PHY) */ miiphy_reset (dev->name, reg); #if defined(CONFIG_440GX) || \ @@ -1080,8 +1218,25 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) } #endif /* #ifndef CONFIG_CS8952_PHY */ - speed = miiphy_speed (dev->name, reg); - duplex = miiphy_duplex (dev->name, reg); +get_speed: + if (reg == CONFIG_FIXED_PHY) { + for (i = 0; i < ARRAY_SIZE(fixed_phy_port); i++) { + if (devnum == fixed_phy_port[i].devnum) { + speed = fixed_phy_port[i].speed; + duplex = fixed_phy_port[i].duplex; + break; + } + } + + if (i == ARRAY_SIZE(fixed_phy_port)) { + printf("ERROR: PHY (%s) not configured correctly!\n", + dev->name); + return -1; + } + } else { + speed = miiphy_speed(dev->name, reg); + duplex = miiphy_duplex(dev->name, reg); + } if (hw_p->print_speed) { hw_p->print_speed = 0; diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c index c882720..d303598 100644 --- a/cpu/ppc4xx/miiphy.c +++ b/cpu/ppc4xx/miiphy.c @@ -180,8 +180,10 @@ int phy_setup_aneg (char *devname, unsigned char addr) * * sr: Currently on 460EX only EMAC0 works with MDIO, so we always * return EMAC0 offset here + * vg: For 460EX/460GT if internal GPCS PHY address is specified + * return appropriate EMAC offset */ -unsigned int miiphy_getemac_offset (void) +unsigned int miiphy_getemac_offset(u8 addr) { #if (defined(CONFIG_440) && \ !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \ @@ -233,6 +235,39 @@ unsigned int miiphy_getemac_offset (void) return 0x100; #endif +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) + u32 mode_reg; + u32 eoffset = 0; + + switch (addr) { +#if defined(CONFIG_HAS_ETH1) && defined(CONFIG_GPCS_PHY1_ADDR) + case CONFIG_GPCS_PHY1_ADDR: + mode_reg = in_be32((void *)EMAC_M1 + 0x100); + if (addr == EMAC_M1_IPPA_GET(mode_reg)) + eoffset = 0x100; + break; +#endif +#if defined(CONFIG_HAS_ETH2) && defined(CONFIG_GPCS_PHY2_ADDR) + case CONFIG_GPCS_PHY2_ADDR: + mode_reg = in_be32((void *)EMAC_M1 + 0x300); + if (addr == EMAC_M1_IPPA_GET(mode_reg)) + eoffset = 0x300; + break; +#endif +#if defined(CONFIG_HAS_ETH3) && defined(CONFIG_GPCS_PHY3_ADDR) + case CONFIG_GPCS_PHY3_ADDR: + mode_reg = in_be32((void *)EMAC_M1 + 0x400); + if (addr == EMAC_M1_IPPA_GET(mode_reg)) + eoffset = 0x400; + break; +#endif + default: + eoffset = 0; + break; + } + return eoffset; +#endif + return 0; #endif } @@ -262,7 +297,7 @@ static int emac_miiphy_command(u8 addr, u8 reg, int cmd, u16 value) u32 emac_reg; u32 sta_reg; - emac_reg = miiphy_getemac_offset(); + emac_reg = miiphy_getemac_offset(addr); /* wait for completion */ if (emac_miiphy_wait(emac_reg) != 0) @@ -311,7 +346,7 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, unsigned char reg, unsigned long sta_reg; unsigned long emac_reg; - emac_reg = miiphy_getemac_offset (); + emac_reg = miiphy_getemac_offset(addr); if (emac_miiphy_command(addr, reg, EMAC_STACR_READ, 0) != 0) return -1; diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h index b74c6fc..00669a7 100644 --- a/include/ppc4xx_enet.h +++ b/include/ppc4xx_enet.h @@ -376,6 +376,7 @@ typedef struct emac_4xx_hw_st { #define EMAC_M1_APP (0x08000000) #define EMAC_M1_RSVD (0x06000000) #define EMAC_M1_IST (0x01000000) +#define EMAC_M1_MF_1000GPCS (0x00C00000) #define EMAC_M1_MF_1000MBPS (0x00800000) /* 0's for 10MBPS */ #define EMAC_M1_MF_100MBPS (0x00400000) #define EMAC_M1_RFS_MASK (0x00380000) @@ -394,6 +395,8 @@ typedef struct emac_4xx_hw_st { #define EMAC_M1_MWSW (0x00007000) #define EMAC_M1_JUMBO_ENABLE (0x00000800) #define EMAC_M1_IPPA (0x000007c0) +#define EMAC_M1_IPPA_SET(id) (((id) & 0x1f) << 6) +#define EMAC_M1_IPPA_GET(id) (((id) >> 6) & 0x1f) #define EMAC_M1_OBCI_GT100 (0x00000020) #define EMAC_M1_OBCI_100 (0x00000018) #define EMAC_M1_OBCI_83 (0x00000010) -- cgit v0.10.2 From 725b53ac61f4df3026b8f6489ef0080fd27d3816 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Sep 2008 14:09:09 +0200 Subject: ppc4xx: Fix compilation warning for canyonlands & glacier Signed-off-by: Stefan Roese diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c index d303598..84b1bbe 100644 --- a/cpu/ppc4xx/miiphy.c +++ b/cpu/ppc4xx/miiphy.c @@ -236,28 +236,24 @@ unsigned int miiphy_getemac_offset(u8 addr) #endif #if defined(CONFIG_460EX) || defined(CONFIG_460GT) - u32 mode_reg; u32 eoffset = 0; switch (addr) { #if defined(CONFIG_HAS_ETH1) && defined(CONFIG_GPCS_PHY1_ADDR) case CONFIG_GPCS_PHY1_ADDR: - mode_reg = in_be32((void *)EMAC_M1 + 0x100); - if (addr == EMAC_M1_IPPA_GET(mode_reg)) + if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x100))) eoffset = 0x100; break; #endif #if defined(CONFIG_HAS_ETH2) && defined(CONFIG_GPCS_PHY2_ADDR) case CONFIG_GPCS_PHY2_ADDR: - mode_reg = in_be32((void *)EMAC_M1 + 0x300); - if (addr == EMAC_M1_IPPA_GET(mode_reg)) + if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x300))) eoffset = 0x300; break; #endif #if defined(CONFIG_HAS_ETH3) && defined(CONFIG_GPCS_PHY3_ADDR) case CONFIG_GPCS_PHY3_ADDR: - mode_reg = in_be32((void *)EMAC_M1 + 0x400); - if (addr == EMAC_M1_IPPA_GET(mode_reg)) + if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x400))) eoffset = 0x400; break; #endif -- cgit v0.10.2 From 6ca8646c1860bba74326bf916a5a3389a5c0d3b5 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Sep 2008 14:11:40 +0200 Subject: ppc4xx: Fix compilation warning for PIP405 This patch fixes a compilation warning for the PIP405 board. It moves the #ifndef CONFIG_CS8952_PHY define a little so that the warning doesn't occur anymore. I am a little unsure if this #ifdef is at the correct place now or if it could be removed completely. This needs to get tested on the PIP405 board. Signed-off-by: Stefan Roese diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 071ac0a..52486fd 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -1061,7 +1061,6 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) /* wait for PHY to complete auto negotiation */ reg_short = 0; -#ifndef CONFIG_CS8952_PHY switch (devnum) { case 0: reg = CONFIG_PHY_ADDR; @@ -1160,7 +1159,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) miiphy_write (dev->name, reg, 0x1f, 0x0000); /* end Vitesse/Cicada errata */ } -#endif +#endif /* defined(CONFIG_CIS8201_PHY) */ #if defined(CONFIG_ET1011C_PHY) /* @@ -1179,15 +1178,16 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) miiphy_write(dev->name, reg, 0x1c, 0x74f0); } -#endif +#endif /* defined(CONFIG_ET1011C_PHY) */ -#endif +#endif /* defined(CONFIG_440GX) ... */ /* Start/Restart autonegotiation */ phy_setup_aneg (dev->name, reg); udelay (1000); } #endif /* defined(CONFIG_PHY_RESET) */ +#if !defined(CONFIG_CS8952_PHY) miiphy_read (dev->name, reg, PHY_BMSR, ®_short); /* @@ -1211,12 +1211,11 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) } udelay (1000); /* 1 ms */ miiphy_read (dev->name, reg, PHY_BMSR, ®_short); - } puts (" done\n"); udelay (500000); /* another 500 ms (results in faster booting) */ } -#endif /* #ifndef CONFIG_CS8952_PHY */ +#endif /* !defined(CONFIG_CS8952_PHY) */ get_speed: if (reg == CONFIG_FIXED_PHY) { -- cgit v0.10.2 From f071f01fd09e9bf1cf09de37a7416aacce71bae1 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 8 Sep 2008 10:01:48 +0200 Subject: ppc4xx: Remove CONFIG_CS8952_PHY define Since this define is only used on one board that was never really in production, removing this compile time option doesn't hurt and makes the code more readable. Signed-off-by: Stefan Roese diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 52486fd..6d4d043 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -1187,7 +1187,6 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) } #endif /* defined(CONFIG_PHY_RESET) */ -#if !defined(CONFIG_CS8952_PHY) miiphy_read (dev->name, reg, PHY_BMSR, ®_short); /* @@ -1215,7 +1214,6 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) puts (" done\n"); udelay (500000); /* another 500 ms (results in faster booting) */ } -#endif /* !defined(CONFIG_CS8952_PHY) */ get_speed: if (reg == CONFIG_FIXED_PHY) { diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h index 2ceda00..86ea6c6 100644 --- a/include/configs/PIP405.h +++ b/include/configs/PIP405.h @@ -281,7 +281,6 @@ ***********************************************************/ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ -#define CONFIG_CS8952_PHY 1 /* its a CS8952 PHY */ /************************************************************ * RTC ***********************************************************/ -- cgit v0.10.2 From 767f9159c5c94cd0cb3135b5b82814ad12816ddf Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 5 Sep 2008 15:34:02 +0200 Subject: ppc4xx: Update CPCI405 variants handling This patch replaces the BOARD_REVISION variable in include/config.mk by a using a temporary include file in the platform directory. The former way does not work anymore and the latter is also used by some other boards. Signed-off-by: Matthias Fuchs Signed-off-by: Stefan Roese diff --git a/Makefile b/Makefile index 3869e79..ae3db0a 100644 --- a/Makefile +++ b/Makefile @@ -1242,12 +1242,14 @@ CMS700_config: unconfig CPCI2DP_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci2dp esd -CPCI405_config \ -CPCI4052_config \ +CPCI405_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci405 esd + +CPCI4052_config \ CPCI405DT_config \ CPCI405AB_config: unconfig + @echo "TEXT_BASE = 0xFFFC0000" > $(obj)board/esd/cpci405/config.tmp @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci405 esd - @echo "BOARD_REVISION = $(@:_config=)" >> $(obj)include/config.mk CPCIISER4_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpciiser4 esd diff --git a/board/esd/cpci405/config.mk b/board/esd/cpci405/config.mk index 0be45c7..6cfb891 100644 --- a/board/esd/cpci405/config.mk +++ b/board/esd/cpci405/config.mk @@ -21,20 +21,8 @@ # MA 02111-1307 USA # -# -# esd CPCI405 boards -# +sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp -ifeq ($(BOARD_REVISION),CPCI4052) -TEXT_BASE = 0xFFFC0000 -else -ifeq ($(BOARD_REVISION),CPCI405DT) -TEXT_BASE = 0xFFFC0000 -else -ifeq ($(BOARD_REVISION),CPCI405AB) -TEXT_BASE = 0xFFFC0000 -else +ifndef TEXT_BASE TEXT_BASE = 0xFFFD0000 endif -endif -endif -- cgit v0.10.2 From 7b1fbcadf73a83b3beb94abccda1c35e2c075a94 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 5 Sep 2008 15:34:03 +0200 Subject: ppc4xx: Cleanup CPCI405 linker script Signed-off-by: Matthias Fuchs Signed-off-by: Stefan Roese diff --git a/board/esd/cpci405/u-boot.lds b/board/esd/cpci405/u-boot.lds index 21547ac..2a1fc31 100644 --- a/board/esd/cpci405/u-boot.lds +++ b/board/esd/cpci405/u-boot.lds @@ -57,22 +57,7 @@ SECTIONS .plt : { *(.plt) } .text : { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - cpu/ppc4xx/start.o (.text) - cpu/ppc4xx/traps.o (.text) - cpu/ppc4xx/interrupts.o (.text) - cpu/ppc4xx/4xx_uart.o (.text) - cpu/ppc4xx/cpu_init.o (.text) - cpu/ppc4xx/speed.o (.text) - common/dlmalloc.o (.text) - lib_generic/crc32.o (.text) - lib_ppc/extable.o (.text) - lib_generic/zlib.o (.text) - -/* . = env_offset;*/ -/* common/environment.o(.text)*/ *(.text) *(.fixup) -- cgit v0.10.2 From ac53ee8318678190bf3c68da477a84a657d86fb0 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 5 Sep 2008 15:34:04 +0200 Subject: ppc4xx: Update CPCI405(AB) configuration This patch add FDT support and command line editing capabilities for CPCI405 and CPCI405AB boards. Signed-off-by: Matthias Fuchs Signed-off-by: Stefan Roese diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index fd49f56..9ec1721 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -146,6 +146,8 @@ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_CMDLINE_EDITING /* add command line history */ + #define CONFIG_LOOPW 1 /* enable loopw command */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ @@ -219,6 +221,10 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + /*----------------------------------------------------------------------- * FLASH organization */ diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index 55dd629..7899598 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -144,6 +144,8 @@ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_CMDLINE_EDITING /* add command line history */ + #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ @@ -215,6 +217,10 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + /*----------------------------------------------------------------------- * FLASH organization */ -- cgit v0.10.2 From 5ff889349d2ace13f10c9335e09365fcec8247cc Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 8 Sep 2008 14:11:12 +0200 Subject: ppc4xx: Move ppc4xx specific prototypes to ppc4xx header This patch moves some 4xx specific prototypes out of include common.h to a ppc4xx specific header. Signed-off-by: Stefan Roese diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c index 66a958c..e5df62e 100644 --- a/board/netstal/hcu5/sdram.c +++ b/board/netstal/hcu5/sdram.c @@ -122,7 +122,7 @@ void sdram_panic(const char *reason) } #ifdef CONFIG_DDR_ECC -static void blank_string(int size) +void blank_string(int size) { int i; diff --git a/include/asm-ppc/ppc4xx-sdram.h b/include/asm-ppc/ppc4xx-sdram.h index a1ef029..8efa557 100644 --- a/include/asm-ppc/ppc4xx-sdram.h +++ b/include/asm-ppc/ppc4xx-sdram.h @@ -1402,4 +1402,18 @@ #endif /* CONFIG_SDRAM_PPC4xx_DENALI_DDR2 */ +#ifndef __ASSEMBLY__ +/* + * Prototypes + */ +void inline blank_string(int size); +inline void ppc4xx_ibm_ddr2_register_dump(void); +u32 mfdcr_any(u32); +void mtdcr_any(u32, u32); +u32 ddr_wrdtr(u32); +u32 ddr_clktr(u32); +void spd_ddr_init_hang(void); +u32 DQS_autocalibration(void); +#endif /* __ASSEMBLY__ */ + #endif /* _PPC4xx_SDRAM_H_ */ diff --git a/include/common.h b/include/common.h index 2516bfd..a394988 100644 --- a/include/common.h +++ b/include/common.h @@ -287,27 +287,6 @@ void pciinfo (int, int); #endif #endif -/* - * Prototypes - */ -#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) -void blank_string(int); -inline void ppc4xx_ibm_ddr2_register_dump(void); -#if defined(CONFIG_440) -u32 mfdcr_any(u32); -void mtdcr_any(u32, u32); -#endif -#if defined(CONFIG_SPD_EEPROM) -u32 ddr_wrdtr(u32); -u32 ddr_clktr(u32); -void spd_ddr_init_hang(void); -#endif -#endif /* defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) */ - -#if defined(CONFIG_PPC4xx_DDR_AUTOCALIBRATION) -u32 DQS_autocalibration(void); -#endif /* CONFIG_PPC4xx_DDR_AUTOCALIBRATION */ - int misc_init_f (void); int misc_init_r (void); -- cgit v0.10.2