From e221174377d7e3ee848e014b96430d4c97023e93 Mon Sep 17 00:00:00 2001 From: wdenk Date: Sat, 2 Nov 2002 23:30:20 +0000 Subject: Initial revision diff --git a/board/hymod/global_env b/board/hymod/global_env new file mode 100644 index 0000000..913f82d --- /dev/null +++ b/board/hymod/global_env @@ -0,0 +1,69 @@ +# format of this file is: +# +# 1. blank lines and lines beginning with '#' are ignored +# 2. all other lines must have the form = +# 3. if a percent appears anywhere, it is replaced like so: +# +# %s serial number of the main board (10 digit zero filled) +# %S serial number of the main board (plain number) +# %% a percentage character +# +# no whitespace is removed in either or +# +# if first character in is a dash ('-'), then an existing env var +# will not be overwritten (the dash is removed). +# +# if last character in is a plus ('+'), then will be appended +# to any existing env var (the plus is removed). Duplicates of are +# removed. +# + +# set the ip address based on the main board serial number +ipaddr=192.168.1.%S +serverip=192.168.1.254 + +# stop auto execute after tftp +autostart=no + +# +# 16M flash map, 64 x 256K sectors, mapped at address 0x40000000 +# +# sector 0: boot +# sector 1: non volatile environment +# sectors 2-4: linux kernel image +# sectors 5-7: alternate linux kernel image +# sectors 8-63: linux initial ramdisk image +# + +fetchboot=tftp 100000 /hymod/u-boot.bin +eraseboot=protect off 1:0 ; erase 1:0 ; protect on 1:0 +copyboot=protect off 1:0 ; cp.b 100000 40000000 40000 ; protect on 1:0 +cmpboot=cmp.b 100000 40000000 40000 +newboot=run fetchboot eraseboot copyboot cmpboot + +fetchlinux=tftp 100000 /hymod/linux.bin +eraselinux=erase 1:2-4 +copylinux=cp.b 100000 40080000 $(filesize) +cmplinux=cmp.b 100000 40080000 $(filesize) +newlinux=run fetchlinux eraselinux copylinux cmplinux + +fetchaltlinux=tftp 100000 /hymod/altlinux.bin +erasealtlinux=erase 1:5-7 +copyaltlinux=cp.b 100000 40080000 $(filesize) +cmpaltlinux=cmp.b 100000 40080000 $(filesize) +newaltlinux=run fetchaltlinux erasealtlinux copyaltlinux cmpaltlinux + +fetchird=tftp 100000 /hymod/initrd.bin +eraseird=erase 1:8-63 +copyird=cp.b 100000 40200000 $(filesize) +cmpird=cmp.b 100000 40200000 $(filesize) +newinitrd=run fetchird eraseird copyird cmpird + +bootcmd=bootm 40080000 40200000 +-bootargs=root=/dev/ram rw +# these are for hymod linux +bootargs+=preload=unix,i2c-cpm,i2c-dev +bootargs+=serialno=%S +bootargs+=ramdisk_size=32768 +bootargs+=automount nisclient nisdomain=mlb.dmt.csiro.au nissrvadr=138.194.112.4 +bootdelay=2 diff --git a/board/lwmon/lwmon.c b/board/lwmon/lwmon.c new file mode 100644 index 0000000..e797b36 --- /dev/null +++ b/board/lwmon/lwmon.c @@ -0,0 +1,966 @@ +/*********************************************************************** + * +M* Modul: lwmon.c +M* +M* Content: LWMON specific U-Boot commands. + * + * (C) Copyright 2001, 2002 + * DENX Software Engineering + * Wolfgang Denk, wd@denx.de + * All rights reserved. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + ***********************************************************************/ + +/*---------------------------- Headerfiles ----------------------------*/ +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include /* for strdup */ + +/*------------------------ Local prototypes ---------------------------*/ +static long int dram_size (long int, long int *, long int); + + +/*--------------------- Local macros and constants --------------------*/ +#define _NOT_USED_ 0xFFFFFFFF + +/* + * 66 MHz SDRAM access using UPM A + */ +const uint sdram_table[] = +{ +#if defined(CFG_MEMORY_75) || defined(CFG_MEMORY_8E) + /* + * Single Read. (Offset 0 in UPM RAM) + */ + 0x1F0DFC04, 0xEEAFBC04, 0x11AF7C04, 0xEFBAFC00, + 0x1FF5FC47, /* last */ + /* + * SDRAM Initialization (offset 5 in UPM RAM) + * + * This is no UPM entry point. The following definition uses + * the remaining space to establish an initialization + * sequence, which is executed by a RUN command. + * + */ + 0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */ + /* + * Burst Read. (Offset 8 in UPM RAM) + */ + 0x1F0DFC04, 0xEEAFBC04, 0x10AF7C04, 0xF0AFFC00, + 0xF0AFFC00, 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */ + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Single Write. (Offset 18 in UPM RAM) + */ + 0x1F2DFC04, 0xEEABBC00, 0x01B27C04, 0x1FF5FC47, /* last */ + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Burst Write. (Offset 20 in UPM RAM) + */ + 0x1F0DFC04, 0xEEABBC00, 0x10A77C00, 0xF0AFFC00, + 0xF0AFFC00, 0xE1BAFC04, 0x01FF5FC47, /* last */ + _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Refresh (Offset 30 in UPM RAM) + */ + 0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC84, 0xFFFFFC07, /* last */ + _NOT_USED_, _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Exception. (Offset 3c in UPM RAM) + */ + 0x7FFFFC07, /* last */ + 0xFFFFFCFF, 0xFFFFFCFF, 0xFFFFFCFF, +#endif +#ifdef CFG_MEMORY_7E + /* + * Single Read. (Offset 0 in UPM RAM) + */ + 0x0E2DBC04, 0x11AF7C04, 0xEFBAFC00, 0x1FF5FC47, /* last */ + _NOT_USED_, + /* + * SDRAM Initialization (offset 5 in UPM RAM) + * + * This is no UPM entry point. The following definition uses + * the remaining space to establish an initialization + * sequence, which is executed by a RUN command. + * + */ + 0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */ + /* + * Burst Read. (Offset 8 in UPM RAM) + */ + 0x0E2DBC04, 0x10AF7C04, 0xF0AFFC00, 0xF0AFFC00, + 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */ + _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Single Write. (Offset 18 in UPM RAM) + */ + 0x0E29BC04, 0x01B27C04, 0x1FF5FC47, /* last */ + _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Burst Write. (Offset 20 in UPM RAM) + */ + 0x0E29BC04, 0x10A77C00, 0xF0AFFC00, 0xF0AFFC00, + 0xE1BAFC04, 0x1FF5FC47, /* last */ + _NOT_USED_, _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Refresh (Offset 30 in UPM RAM) + */ + 0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC84, 0xFFFFFC07, /* last */ + _NOT_USED_, _NOT_USED_, + _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_, + /* + * Exception. (Offset 3c in UPM RAM) + */ + 0x7FFFFC07, /* last */ + 0xFFFFFCFF, 0xFFFFFCFF, 0xFFFFFCFF, +#endif +}; + +/* + * Check Board Identity: + * + */ + +/*********************************************************************** +F* Function: int checkboard (void) P*A*Z* + * +P* Parameters: none +P* +P* Returnvalue: int - 0 is always returned + * +Z* Intention: This function is the checkboard() method implementation +Z* for the lwmon board. Only a standard message is printed. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +int checkboard (void) +{ + puts ("Board: Litronic Monitor IV\n"); + return (0); +} + +/*********************************************************************** +F* Function: long int initdram (int board_type) P*A*Z* + * +P* Parameters: int board_type +P* - Usually type of the board - ignored here. +P* +P* Returnvalue: long int +P* - Size of initialized memory + * +Z* Intention: This function is the initdram() method implementation +Z* for the lwmon board. +Z* The memory controller is initialized to access the +Z* DRAM. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +long int initdram (int board_type) +{ + volatile immap_t *immr = (immap_t *) CFG_IMMR; + volatile memctl8xx_t *memctl = &immr->im_memctl; + long int size_b0; + long int size8, size9; + int i; + + /* + * Configure UPMA for SDRAM + */ + upmconfig (UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint)); + + memctl->memc_mptpr = CFG_MPTPR; + + /* burst length=4, burst type=sequential, CAS latency=2 */ + memctl->memc_mar = CFG_MAR; + + /* + * Map controller bank 3 to the SDRAM bank at preliminary address. + */ + memctl->memc_or3 = CFG_OR3_PRELIM; + memctl->memc_br3 = CFG_BR3_PRELIM; + + /* initialize memory address register */ + memctl->memc_mamr = CFG_MAMR_8COL; /* refresh not enabled yet */ + + /* mode initialization (offset 5) */ + udelay (200); /* 0x80006105 */ + memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x05); + + /* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */ + udelay (1); /* 0x80006130 */ + memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x30); + udelay (1); /* 0x80006130 */ + memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x30); + + udelay (1); /* 0x80006106 */ + memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x06); + + memctl->memc_mamr |= MAMR_PTBE; /* refresh enabled */ + + udelay (200); + + /* Need at least 10 DRAM accesses to stabilize */ + for (i = 0; i < 10; ++i) { + volatile unsigned long *addr = + (volatile unsigned long *) SDRAM_BASE3_PRELIM; + unsigned long val; + + val = *(addr + i); + *(addr + i) = val; + } + + /* + * Check Bank 0 Memory Size for re-configuration + * + * try 8 column mode + */ + size8 = dram_size (CFG_MAMR_8COL, (ulong *)SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE); + + udelay (1000); + + /* + * try 9 column mode + */ + size9 = dram_size (CFG_MAMR_9COL, (ulong *)SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE); + + if (size8 < size9) { /* leave configuration at 9 columns */ + size_b0 = size9; + memctl->memc_mamr = CFG_MAMR_9COL | MAMR_PTBE; + udelay (500); + } else { /* back to 8 columns */ + size_b0 = size8; + memctl->memc_mamr = CFG_MAMR_8COL | MAMR_PTBE; + udelay (500); + } + + /* + * Final mapping: + */ + + memctl->memc_or3 = ((-size_b0) & 0xFFFF0000) | + OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING; + memctl->memc_br3 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; + udelay (1000); + + return (size_b0); +} + +/*********************************************************************** +F* Function: static long int dram_size (long int mamr_value, +F* long int *base, +F* long int maxsize) P*A*Z* + * +P* Parameters: long int mamr_value +P* - Value for MAMR for the test +P* long int *base +P* - Base address for the test +P* long int maxsize +P* - Maximum size to test for +P* +P* Returnvalue: long int +P* - Size of probed memory + * +Z* Intention: Check memory range for valid RAM. A simple memory test +Z* determines the actually available RAM size between +Z* addresses `base' and `base + maxsize'. Some (not all) +Z* hardware errors are detected: +Z* - short between address lines +Z* - short between data lines + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +static long int dram_size (long int mamr_value, long int *base, long int maxsize) +{ + volatile immap_t *immr = (immap_t *) CFG_IMMR; + volatile memctl8xx_t *memctl = &immr->im_memctl; + volatile long int *addr; + ulong cnt, val; + ulong save[32]; /* to make test non-destructive */ + unsigned char i = 0; + + memctl->memc_mamr = mamr_value; + + for (cnt = maxsize / sizeof (long); cnt > 0; cnt >>= 1) { + addr = base + cnt; /* pointer arith! */ + + save[i++] = *addr; + *addr = ~cnt; + } + + /* write 0 to base address */ + addr = base; + save[i] = *addr; + *addr = 0; + + /* check at base address */ + if ((val = *addr) != 0) { + *addr = save[i]; + return (0); + } + + for (cnt = 1; cnt <= maxsize / sizeof (long); cnt <<= 1) { + addr = base + cnt; /* pointer arith! */ + + val = *addr; + *addr = save[--i]; + + if (val != (~cnt)) { + return (cnt * sizeof (long)); + } + } + return (maxsize); +} + +/* ------------------------------------------------------------------------- */ + +#ifndef PB_ENET_TENA +# define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ +#endif + +/*********************************************************************** +F* Function: int board_pre_init (void) P*A*Z* + * +P* Parameters: none +P* +P* Returnvalue: int +P* - 0 is always returned. + * +Z* Intention: This function is the board_pre_init() method implementation +Z* for the lwmon board. +Z* Disable Ethernet TENA on Port B. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +int board_pre_init (void) +{ + volatile immap_t *immr = (immap_t *) CFG_IMMR; + + /* Disable Ethernet TENA on Port B + * Necessary because of pull up in COM3 port. + * + * This is just a preliminary fix, intended to turn off TENA + * as soon as possible to avoid noise on the network. Once + * I²C is running we will make sure the interface is + * correctly initialized. + */ + immr->im_cpm.cp_pbpar &= ~PB_ENET_TENA; + immr->im_cpm.cp_pbodr &= ~PB_ENET_TENA; + immr->im_cpm.cp_pbdat &= ~PB_ENET_TENA; /* set to 0 = disabled */ + immr->im_cpm.cp_pbdir |= PB_ENET_TENA; + return (0); +} + +/* ------------------------------------------------------------------------- */ + +/*********************************************************************** +F* Function: void reset_phy (void) P*A*Z* + * +P* Parameters: none +P* +P* Returnvalue: none + * +Z* Intention: Reset the PHY. In the lwmon case we do this by the +Z* signaling the PIC I/O expander. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +void reset_phy (void) +{ + uchar c; + +#ifdef DEBUG + printf ("### Switch on Ethernet for SCC2 ###\n"); +#endif + c = pic_read (0x61); +#ifdef DEBUG + printf ("Old PIC read: reg_61 = 0x%02x\n", c); +#endif + c |= 0x40; /* disable COM3 */ + c &= ~0x80; /* enable Ethernet */ + pic_write (0x61, c); +#ifdef DEBUG + c = pic_read (0x61); + printf ("New PIC read: reg_61 = 0x%02x\n", c); +#endif + udelay (1000); +} + + +/*------------------------- Keyboard controller -----------------------*/ +/* command codes */ +#define KEYBD_CMD_READ_KEYS 0x01 +#define KEYBD_CMD_READ_VERSION 0x02 +#define KEYBD_CMD_READ_STATUS 0x03 +#define KEYBD_CMD_RESET_ERRORS 0x10 + +/* status codes */ +#define KEYBD_STATUS_MASK 0x3F +#define KEYBD_STATUS_H_RESET 0x20 +#define KEYBD_STATUS_BROWNOUT 0x10 +#define KEYBD_STATUS_WD_RESET 0x08 +#define KEYBD_STATUS_OVERLOAD 0x04 +#define KEYBD_STATUS_ILLEGAL_WR 0x02 +#define KEYBD_STATUS_ILLEGAL_RD 0x01 + +/* Number of bytes returned from Keyboard Controller */ +#define KEYBD_VERSIONLEN 2 /* version information */ +#define KEYBD_DATALEN 9 /* normal key scan data */ + +/* maximum number of "magic" key codes that can be assigned */ + +static uchar kbd_addr = CFG_I2C_KEYBD_ADDR; + +static uchar *key_match (uchar *); + +#define KEYBD_SET_DEBUGMODE '#' /* Magic key to enable debug output */ + +/*********************************************************************** +F* Function: int misc_init_r (void) P*A*Z* + * +P* Parameters: none +P* +P* Returnvalue: int +P* - 0 is always returned, even in the case of a keyboard +P* error. + * +Z* Intention: This function is the misc_init_r() method implementation +Z* for the lwmon board. +Z* The keyboard controller is initialized and the result +Z* of a read copied to the environment variable "keybd". +Z* If KEYBD_SET_DEBUGMODE is defined, a check is made for +Z* this key, and if found display to the LCD will be enabled. +Z* The keys in "keybd" are checked against the magic +Z* keycommands defined in the environment. +Z* See also key_match(). + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +int misc_init_r (void) +{ + uchar kbd_data[KEYBD_DATALEN]; + uchar tmp_data[KEYBD_DATALEN]; + uchar keybd_env[2 * KEYBD_DATALEN + 1]; + uchar val, errcd; + uchar *str; + int i; + + i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE); + + /* Read initial keyboard error code */ + val = KEYBD_CMD_READ_STATUS; + i2c_write (kbd_addr, 0, 0, &val, 1); + i2c_read (kbd_addr, 0, 0, &errcd, 1); + /* clear unused bits */ + errcd &= KEYBD_STATUS_MASK; + /* clear "irrelevant" bits. Recommended by Martin Rajek, LWN */ + errcd &= ~(KEYBD_STATUS_H_RESET|KEYBD_STATUS_BROWNOUT); + if (errcd) { + printf ("KEYBD: Error %02X\n", errcd); + } + /* Reset error code and verify */ + val = KEYBD_CMD_RESET_ERRORS; + i2c_write (kbd_addr, 0, 0, &val, 1); + udelay(1000); /* delay NEEDED by keyboard PIC !!! */ + + val = KEYBD_CMD_READ_STATUS; + i2c_write (kbd_addr, 0, 0, &val, 1); + i2c_read (kbd_addr, 0, 0, &val, 1); + + val &= KEYBD_STATUS_MASK; /* clear unused bits */ + if (val) { /* permanent error, report it */ + printf ("*** Keyboard error code %02X ***\n", val); + sprintf (keybd_env, "%02X", val); + setenv ("keybd", keybd_env); + return 0; + } + + /* + * Now we know that we have a working keyboard, so disable + * all output to the LCD except when a key press is detected. + */ + + if ((console_assign (stdout, "serial") < 0) || + (console_assign (stderr, "serial") < 0)) { + printf ("Can't assign serial port as output device\n"); + } + + /* Read Version */ + val = KEYBD_CMD_READ_VERSION; + i2c_write (kbd_addr, 0, 0, &val, 1); + i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_VERSIONLEN); + printf ("KEYBD: Version %d.%d\n", kbd_data[0], kbd_data[1]); + + /* + * Read current keyboard state. + * + * After the error reset it may take some time before the + * keyboard PIC picks up a valid keyboard scan - the total + * scan time is approx. 1.6 ms (information by Martin Rajek, + * 28 Sep 2002). We read a couple of times for the keyboard + * to stabilize, using a big enough delay. + * 10 times should be enough. If the data is still changing, + * we use what we get :-( + */ + + memset (tmp_data, 0xFF, KEYBD_DATALEN); /* impossible value */ + for (i=0; i<10; ++i) { + val = KEYBD_CMD_READ_KEYS; + i2c_write (kbd_addr, 0, 0, &val, 1); + i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN); + + if (memcmp(kbd_data, tmp_data, KEYBD_DATALEN) == 0) { + /* consistent state, done */ + break; + } + /* remeber last state, delay, and retry */ + memcpy (tmp_data, kbd_data, KEYBD_DATALEN); + udelay (5000); + } + + for (i = 0; i < KEYBD_DATALEN; ++i) { + sprintf (keybd_env + i + i, "%02X", kbd_data[i]); + } + setenv ("keybd", keybd_env); + + str = strdup (key_match (kbd_data)); /* decode keys */ +#ifdef KEYBD_SET_DEBUGMODE + if (kbd_data[0] == KEYBD_SET_DEBUGMODE) { /* set debug mode */ + if ((console_assign (stdout, "lcd") < 0) || + (console_assign (stderr, "lcd") < 0)) { + printf ("Can't assign LCD display as output device\n"); + } + } +#endif /* KEYBD_SET_DEBUGMODE */ +#ifdef CONFIG_PREBOOT /* automatically configure "preboot" command on key match */ + setenv ("preboot", str); /* set or delete definition */ +#endif /* CONFIG_PREBOOT */ + if (str != NULL) { + free (str); + } + return (0); +} + +#ifdef CONFIG_PREBOOT + +static uchar kbd_magic_prefix[] = "key_magic"; +static uchar kbd_command_prefix[] = "key_cmd"; + +/*********************************************************************** +F* Function: static uchar *key_match (uchar *kbd_data) P*A*Z* + * +P* Parameters: uchar *kbd_data +P* - The keys to match against our magic definitions +P* +P* Returnvalue: uchar * +P* - != NULL: Pointer to the corresponding command(s) +P* NULL: No magic is about to happen + * +Z* Intention: Check if pressed key(s) match magic sequence, +Z* and return the command string associated with that key(s). +Z* +Z* If no key press was decoded, NULL is returned. +Z* +Z* Note: the first character of the argument will be +Z* overwritten with the "magic charcter code" of the +Z* decoded key(s), or '\0'. +Z* +Z* Note: the string points to static environment data +Z* and must be saved before you call any function that +Z* modifies the environment. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +static uchar *key_match (uchar *kbd_data) +{ + uchar compare[KEYBD_DATALEN-1]; + uchar magic[sizeof (kbd_magic_prefix) + 1]; + uchar extra; + uchar *str, *nxt, *suffix; + uchar *kbd_magic_keys; + int i; + + /* + * The following string defines the characters that can pe appended + * to "key_magic" to form the names of environment variables that + * hold "magic" key codes, i. e. such key codes that can cause + * pre-boot actions. If the string is empty (""), then only + * "key_magic" is checked (old behaviour); the string "125" causes + * checks for "key_magic1", "key_magic2" and "key_magic5", etc. + */ + if ((kbd_magic_keys = getenv ("magic_keys")) == NULL) + kbd_magic_keys = ""; + + /* loop over all magic keys; + * use '\0' suffix in case of empty string + */ + for (suffix=kbd_magic_keys; *suffix || suffix==kbd_magic_keys; ++suffix) { + sprintf (magic, "%s%c", kbd_magic_prefix, *suffix); +#if 0 + printf ("### Check magic \"%s\"\n", magic); +#endif + /* Don't include modifier byte */ + memcpy (compare, kbd_data+1, KEYBD_DATALEN-1); + + extra = 0; + + for (str= getenv(magic); str != NULL; str = (*nxt) ? nxt+1 : nxt) { + uchar c; + int k; + + c = (uchar) simple_strtoul (str, (char **) (&nxt), 16); + + if (str == nxt) { /* invalid character */ + break; + } + + /* + * Check if this key matches the input. + * Set matches to zero, so they match only once + * and we can find duplicates or extra keys + */ + for (k = 0; k < sizeof(compare); ++k) { + if (compare[k] == '\0') /* only non-zero entries */ + continue; + if (c == compare[k]) { /* found matching key */ + compare[k] = '\0'; + break; + } + } + if (k == sizeof(compare)) { + extra = 1; /* unmatched key */ + } + } + + /* + * A full match leaves no keys in the `compare' array, + * and has no extra keys + */ + + for (i = 0; i < sizeof(compare); ++i) { + if (compare[i]) + break; + } + + if ((i == sizeof(compare)) && (extra == 0)) { + uchar cmd_name[sizeof (kbd_command_prefix) + 1]; + char *cmd; + + sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix); + + cmd = getenv (cmd_name); +#if 0 + printf ("### Set PREBOOT to $(%s): \"%s\"\n", + cmd_name, cmd ? cmd : "<>"); +#endif + *kbd_data = *suffix; + return (cmd); + } + } +#if 0 + printf ("### Delete PREBOOT\n"); +#endif + *kbd_data = '\0'; + return (NULL); +} +#endif /* CONFIG_PREBOOT */ + +/*---------------Board Special Commands: PIC read/write ---------------*/ + +#if (CONFIG_COMMANDS & CFG_CMD_BSP) +/*********************************************************************** +F* Function: int do_pic (cmd_tbl_t *cmdtp, int flag, +F* int argc, char *argv[]) P*A*Z* + * +P* Parameters: cmd_tbl_t *cmdtp +P* - Pointer to our command table entry +P* int flag +P* - If the CMD_FLAG_REPEAT bit is set, then this call is +P* a repetition +P* int argc +P* - Argument count +P* char *argv[] +P* - Array of the actual arguments +P* +P* Returnvalue: int +P* - 0 The command was handled successfully +P* 1 An error occurred + * +Z* Intention: Implement the "pic [read|write]" commands. +Z* The read subcommand takes one argument, the register, +Z* whereas the write command takes two, the register and +Z* the new value. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +int do_pic (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + uchar reg, val; + + switch (argc) { + case 3: /* PIC read reg */ + if (strcmp (argv[1], "read") != 0) + break; + + reg = simple_strtoul (argv[2], NULL, 16); + + printf ("PIC read: reg %02x: %02x\n\n", reg, pic_read (reg)); + + return 0; + case 4: /* PIC write reg val */ + if (strcmp (argv[1], "write") != 0) + break; + + reg = simple_strtoul (argv[2], NULL, 16); + val = simple_strtoul (argv[3], NULL, 16); + + printf ("PIC write: reg %02x val 0x%02x: %02x => ", + reg, val, pic_read (reg)); + pic_write (reg, val); + printf ("%02x\n\n", pic_read (reg)); + return 0; + default: + break; + } + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; +} + +/*********************************************************************** +F* Function: int do_kbd (cmd_tbl_t *cmdtp, int flag, +F* int argc, char *argv[]) P*A*Z* + * +P* Parameters: cmd_tbl_t *cmdtp +P* - Pointer to our command table entry +P* int flag +P* - If the CMD_FLAG_REPEAT bit is set, then this call is +P* a repetition +P* int argc +P* - Argument count +P* char *argv[] +P* - Array of the actual arguments +P* +P* Returnvalue: int +P* - 0 is always returned. + * +Z* Intention: Implement the "kbd" command. +Z* The keyboard status is read. The result is printed on +Z* the console and written into the "keybd" environment +Z* variable. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +int do_kbd (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + uchar kbd_data[KEYBD_DATALEN]; + uchar keybd_env[2 * KEYBD_DATALEN + 1]; + uchar val; + int i; + + i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE); + + /* Read keys */ + val = KEYBD_CMD_READ_KEYS; + i2c_write (kbd_addr, 0, 0, &val, 1); + i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN); + + puts ("Keys:"); + for (i = 0; i < KEYBD_DATALEN; ++i) { + sprintf (keybd_env + i + i, "%02X", kbd_data[i]); + printf (" %02x", kbd_data[i]); + } + putc ('\n'); + setenv ("keybd", keybd_env); + return 0; +} + +/* Read and set LSB switch */ +#define CFG_PC_TXD1_ENA 0x0008 + +/*********************************************************************** +F* Function: int do_lsb (cmd_tbl_t *cmdtp, int flag, +F* int argc, char *argv[]) P*A*Z* + * +P* Parameters: cmd_tbl_t *cmdtp +P* - Pointer to our command table entry +P* int flag +P* - If the CMD_FLAG_REPEAT bit is set, then this call is +P* a repetition +P* int argc +P* - Argument count +P* char *argv[] +P* - Array of the actual arguments +P* +P* Returnvalue: int +P* - 0 The command was handled successfully +P* 1 An error occurred + * +Z* Intention: Implement the "lsb [on|off]" commands. +Z* The lsb is switched according to the first parameter by +Z* by signaling the PIC I/O expander. +Z* Called with no arguments, the current setting is +Z* printed. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +int do_lsb (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + uchar val; + immap_t *immr = (immap_t *) CFG_IMMR; + + switch (argc) { + case 1: /* lsb - print setting */ + val = pic_read (0x60); + printf ("LSB is o%s\n", (val & 0x20) ? "n" : "ff"); + return 0; + case 2: /* lsb on or lsb off - set switch */ + val = pic_read (0x60); + + if (strcmp (argv[1], "on") == 0) { + val |= 0x20; + immr->im_ioport.iop_pcpar &= ~(CFG_PC_TXD1_ENA); + immr->im_ioport.iop_pcdat |= CFG_PC_TXD1_ENA; + immr->im_ioport.iop_pcdir |= CFG_PC_TXD1_ENA; + } else if (strcmp (argv[1], "off") == 0) { + val &= ~0x20; + immr->im_ioport.iop_pcpar &= ~(CFG_PC_TXD1_ENA); + immr->im_ioport.iop_pcdat &= ~(CFG_PC_TXD1_ENA); + immr->im_ioport.iop_pcdir |= CFG_PC_TXD1_ENA; + } else { + break; + } + pic_write (0x60, val); + return 0; + default: + break; + } + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; +} + +#endif /* CFG_CMD_BSP */ + +/*----------------------------- Utilities -----------------------------*/ +/*********************************************************************** +F* Function: uchar pic_read (uchar reg) P*A*Z* + * +P* Parameters: uchar reg +P* - Register to read +P* +P* Returnvalue: uchar +P* - Value read from register + * +Z* Intention: Read a register from the PIC I/O expander. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +uchar pic_read (uchar reg) +{ + return (i2c_reg_read (CFG_I2C_PICIO_ADDR, reg)); +} + +/*********************************************************************** +F* Function: void pic_write (uchar reg, uchar val) P*A*Z* + * +P* Parameters: uchar reg +P* - Register to read +P* uchar val +P* - Value to write +P* +P* Returnvalue: none + * +Z* Intention: Write to a register on the PIC I/O expander. + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +void pic_write (uchar reg, uchar val) +{ + i2c_reg_write (CFG_I2C_PICIO_ADDR, reg, val); +} + +/*---------------------- Board Control Functions ----------------------*/ +/*********************************************************************** +F* Function: void board_poweroff (void) P*A*Z* + * +P* Parameters: none +P* +P* Returnvalue: none + * +Z* Intention: Turn off the battery power and loop endless, so this +Z* should better be the last function you call... + * +D* Design: wd@denx.de +C* Coding: wd@denx.de +V* Verification: dzu@denx.de + ***********************************************************************/ +void board_poweroff (void) +{ + /* Turn battery off */ + ((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pcdat &= ~(1 << (31 - 13)); + + while (1); +} diff --git a/board/musenki/README b/board/musenki/README new file mode 100644 index 0000000..4a1955d --- /dev/null +++ b/board/musenki/README @@ -0,0 +1,301 @@ +U-Boot for a Musenki M-3/M-1 board +--------------------------- + +Musenki M-1 and M-3 have two banks of flash of 4MB or 8MB each. + +In board's notation, bank 0 is the one at the address of 0xFF800000 +and bank 1 is the one at the address of 0xFF000000. + +On power-up the processor jumps to the address of 0xFFF00100, the last +megabyte of the bank 0 of flash. + +Thus, U-Boot is configured to reside in flash starting at the address of +0xFFF00000. The environment space is located in flash separately from +U-Boot, at the address of 0xFF800000. + +There is a Davicom 9102A on-board, but I don't have it working yet. + +U-Boot test results +-------------------- + +x.x Operation on all available serial consoles + +x.x.x CONFIG_CONS_INDEX 1 + + +U-Boot 1.1.1 (Nov 20 2001 - 15:55:32) + +CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache +Board: MUSENKI Local Bus at 100 MHz +DRAM: 32 MB +FLASH: 4 MB +In: serial +Out: serial +Err: serial +Hit any key to stop autoboot: 0 +=> help +autoscr - run script from memory +base - print or set address offset +bdinfo - print Board Info structure +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +bootd - boot default, i.e., run 'bootcmd' +cmp - memory compare +coninfo - print console devices and informations +cp - memory copy +crc32 - checksum calculation +dcache - enable or disable data cache +echo - echo args to console +erase - erase FLASH memory +flinfo - print FLASH memory information +go - start application at address 'addr' +help - print online help +icache - enable or disable instruction cache +iminfo - print header information for application image +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loop - infinite loop on address range +md - memory display +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) +nm - memory modify (constant address) +printenv- print environment variables +protect - enable or disable FLASH write protection +rarpboot- boot image via network using RARP/TFTP protocol +reset - Perform RESET of the CPU +run - run commands in an environment variable +saveenv - save environment variables to persistent storage +setenv - set environment variables +tftpboot- boot image via network using TFTP protocol + and env variables ipaddr and serverip +version - print monitor version +? - alias for 'help' + + + +x.x.x CONFIG_CONS_INDEX 2 + +**** NOT TESTED **** + +x.x Flash Driver Operation + + +Boot 1.1.1 (Nov 20 2001 - 15:55:32) + +CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache +Board: MUSENKI Local Bus at 100 MHz +DRAM: 32 MB +FLASH: 4 MB +*** Warning - bad CRC, using default environment + +In: serial +Out: serial +Err: serial +Hit any key to stop autoboot: 0 +=> +=> md ff800000 +ff800000: 46989bf8 626f6f74 636d643d 626f6f74 F...bootcmd=boot +ff800010: 6d204646 38323030 30300062 6f6f7464 m FF820000.bootd +ff800020: 656c6179 3d350062 61756472 6174653d elay=5.baudrate= +ff800030: 39363030 00636c6f 636b735f 696e5f6d 9600.clocks_in_m +ff800040: 687a3d31 00737464 696e3d73 65726961 hz=1.stdin=seria +ff800050: 6c007374 646f7574 3d736572 69616c00 l.stdout=serial. +ff800060: 73746465 72723d73 65726961 6c006970 stderr=serial.ip +ff800070: 61646472 3d313932 2e313638 2e302e34 addr=192.168.0.4 +ff800080: 32007365 72766572 69703d31 39322e31 2.serverip=192.1 +ff800090: 36382e30 2e380000 00000000 00000000 68.0.8.......... +ff8000a0: 00000000 00000000 00000000 00000000 ................ +ff8000b0: 00000000 00000000 00000000 00000000 ................ +ff8000c0: 00000000 00000000 00000000 00000000 ................ +ff8000d0: 00000000 00000000 00000000 00000000 ................ +ff8000e0: 00000000 00000000 00000000 00000000 ................ +ff8000f0: 00000000 00000000 00000000 00000000 ................ +=> protect off ff800000 ff81ffff +Un-Protected 1 sectors +=> erase ff800000 ff81ffff +Erase Flash from 0xff800000 to 0xff81ffff + done +Erased 1 sectors +=> md ff800000 +ff800000: ffffffff ffffffff ffffffff ffffffff ................ +ff800010: ffffffff ffffffff ffffffff ffffffff ................ +ff800020: ffffffff ffffffff ffffffff ffffffff ................ +ff800030: ffffffff ffffffff ffffffff ffffffff ................ +ff800040: ffffffff ffffffff ffffffff ffffffff ................ +ff800050: ffffffff ffffffff ffffffff ffffffff ................ +ff800060: ffffffff ffffffff ffffffff ffffffff ................ +ff800070: ffffffff ffffffff ffffffff ffffffff ................ +ff800080: ffffffff ffffffff ffffffff ffffffff ................ +ff800090: ffffffff ffffffff ffffffff ffffffff ................ +ff8000a0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000b0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000c0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000d0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000e0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000f0: ffffffff ffffffff ffffffff ffffffff ................ + +x.x.x Information + + +U-Boot 1.1.1 (Nov 20 2001 - 15:55:32) + +CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache +Board: MUSENKI Local Bus at 100 MHz +DRAM: 32 MB +FLASH: 4 MB +*** Warning - bad CRC, using default environment + +In: serial +Out: serial +Err: serial +Hit any key to stop autoboot: 0 +=> flinfo + +Bank # 1: Intel 28F320J3A (32Mbit = 128K x 32) + Size: 4 MB in 32 Sectors + Sector Start Addresses: + FF800000 (RO) FF820000 FF840000 FF860000 FF880000 + FF8A0000 FF8C0000 FF8E0000 FF900000 FF920000 + FF940000 FF960000 FF980000 FF9A0000 FF9C0000 + FF9E0000 FFA00000 FFA20000 FFA40000 FFA60000 + FFA80000 FFAA0000 FFAC0000 FFAE0000 FFB00000 + FFB20000 FFB40000 FFB60000 FFB80000 FFBA0000 + FFBC0000 FFBE0000 + +Bank # 2: missing or unknown FLASH type +=> + + + +x.x.x Flash Programming + + +U-Boot 1.1.1 (Nov 20 2001 - 15:55:32) + +CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache +Board: MUSENKI Local Bus at 100 MHz +DRAM: 32 MB +FLASH: 4 MB + +In: serial +Out: serial +Err: serial +Hit any key to stop autoboot: 0 +=> +=> +=> +=> protect off ff800000 ff81ffff +Un-Protected 1 sectors +=> cp 0 ff800000 20 +Copy to Flash... done +=> md ff800000 +ff800000: 37ce33ec 33cc334c 33c031cc 33cc35cc 7.3.3.3L3.1.3.5. +ff800010: 33ec13ce 30ccb3ec b3c833c4 31c836cc 3...0.....3.1.6. +ff800020: 33cc3b9d 31ec33ee 13ecf3cc 338833ec 3.;.1.3.....3.3. +ff800030: 234c33ec 32cc22cc 33883bdc 534433cc #L3.2.".3.;.SD3. +ff800040: 33cc30c8 31cc32ec 338c33cc 330c33dc 3.0.1.2.3.3.3.3. +ff800050: 33cc13dc 334c534c b1c433d8 128c13cc 3...3LSL..3..... +ff800060: 37ec36cd 33dc33cc bbc9f7e8 bbcc77cc 7.6.3.3.......w. +ff800070: 314c0adc 139c30ed 33cc334c 33c833ec 1L....0.3.3L3.3. +ff800080: ffffffff ffffffff ffffffff ffffffff ................ +ff800090: ffffffff ffffffff ffffffff ffffffff ................ +ff8000a0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000b0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000c0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000d0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000e0: ffffffff ffffffff ffffffff ffffffff ................ +ff8000f0: ffffffff ffffffff ffffffff ffffffff ................ + + +x.x.x Storage of environment variables in flash + + +U-Boot 1.1.1 (Nov 20 2001 - 15:55:32) + +CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache +Board: MUSENKI Local Bus at 100 MHz +DRAM: 32 MB +FLASH: 4 MB +In: serial +Out: serial +Err: serial +Hit any key to stop autoboot: 0 +=> printenv +bootcmd=bootm FF820000 +bootdelay=5 +baudrate=9600 +clocks_in_mhz=1 +stdin=serial +stdout=serial +stderr=serial + +Environment size: 106/16380 bytes +=> setenv myvar 1234 +=> saveenv +Un-Protected 1 sectors +Erasing Flash... + done +Erased 1 sectors +Saving Environment to Flash... +Protected 1 sectors +=> reset + + +U-Boot 1.1.1 (Nov 20 2001 - 15:55:32) + +CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache +Board: MUSENKI Local Bus at 100 MHz +DRAM: 32 MB +FLASH: 4 MB +In: serial +Out: serial +Err: serial +Hit any key to stop autoboot: 0 +=> printenv +bootcmd=bootm FF820000 +bootdelay=5 +baudrate=9600 +clocks_in_mhz=1 +myvar=1234 +stdin=serial +stdout=serial +stderr=serial + +Environment size: 117/16380 bytes + +x.x Image Download and run over serial port + + +U-Boot 1.1.1 (Nov 20 2001 - 15:55:32) + +CPU: MPC8245 Revision 16.20 at 250 MHz: 16 kB I-Cache 16 kB D-Cache +Board: MUSENKI Local Bus at 100 MHz +DRAM: 32 MB +FLASH: 4 MB +In: serial +Out: serial +Err: serial +Hit any key to stop autoboot: 0 +=> loads +## Ready for S-Record download ... + +## First Load Addr = 0x00040000 +## Last Load Addr = 0x00050177 +## Total Size = 0x00010178 = 65912 Bytes +## Start Addr = 0x00040004 +=> go 40004 +## Starting application at 0x00040004 ... +Hello World +argc = 1 +argv[0] = "40004" +argv[1] = "" +Hit any key to exit ... + +## Application terminated, rc = 0x0 + + +x.x Image download and run over ethernet interface + +untested (not working yet, actually) + diff --git a/board/pcippc2/u-boot.lds b/board/pcippc2/u-boot.lds new file mode 100644 index 0000000..25ff2ff --- /dev/null +++ b/board/pcippc2/u-boot.lds @@ -0,0 +1,132 @@ +/* + * (C) Copyright 2001 + * Josh Huber , Mission Critical Linux, Inc. + * + * (C) Copyright 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * u-boot.lds - linker script for U-Boot on the Galileo Eval Board. + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/74xx_7xx/start.o (.text) + +/* store the environment in a seperate sector in the boot flash */ +/* . = env_offset; */ +/* common/environment.o(.text) */ + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/pm826/config.mk b/board/pm826/config.mk new file mode 100644 index 0000000..8502e3f --- /dev/null +++ b/board/pm826/config.mk @@ -0,0 +1,42 @@ +# +# (C) Copyright 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# PM826 boards +# + +# This should be equal to the CFG_FLASH_BASE or +# CFG_BOOTROM_BASE define in config_PM826.h +# for the "final" configuration, with U-Boot +# in flash, or the address in RAM where +# U-Boot is loaded at for debugging. +# + +ifeq ($(CONFIG_BOOT_ROM),y) + TEXT_BASE := 0x60000000 + PLATFORM_CPPFLAGS += -DCONFIG_BOOT_ROM +else + TEXT_BASE := 0x40000000 +endif + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR) diff --git a/board/rpxsuper/readme b/board/rpxsuper/readme new file mode 100644 index 0000000..21267bd --- /dev/null +++ b/board/rpxsuper/readme @@ -0,0 +1,30 @@ +Hi, + +so this is the port to the Embedded Planet RPX Super Board. + +ATTENTION +This code is only tested on the AY-Version, which is an early release with some +hardware bugs. The main problem is that this board uses the default Hard Reset +Configuration Word and not the 4 bytes located at start of FLASH because at +0xFE000000 is no FLASH. The FLASH consists out of 4 chips each 16bits wide. Be +carefull, the bytes are swapped. So DQ0-7 is the high byte, DQ8-15 ist the low +byte. + +The icache can only manually be enabled after reset. +The FLASH and main SDRAM is working with icache enabled. +The local SDRAM can only be used as data memory when icache is enabled. +If U-Boot runs in local SDRAM, TFTP does not work. +The functions in mii_phy.c are all working. Call mii_phy_discover() out of +eth_init() and solve the linker error. +I2C, RTC/NVRAM and PCMCIA are not working yet. + +TODO +The 32MB local SDRAM is working but not shown in the startup messages of +U-Boot. If you locate U-Boot or any other program to this area it won't run. +Turning the ichache off does not solve this problem. + +As I won't buy another RPX Super there might be some little work to do for you +getting this U-Boot port running on the final board. + + +frank.morauf@salzbrenner.com diff --git a/board/siemens/SCM/config.mk b/board/siemens/SCM/config.mk new file mode 100644 index 0000000..855ae38 --- /dev/null +++ b/board/siemens/SCM/config.mk @@ -0,0 +1,34 @@ +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# Siemens SCM boards +# + +# This should be equal to the CFG_FLASH_BASE define in config_SCM.h +# for the "final" configuration, with U-Boot in flash, or the address +# in RAM where U-Boot is loaded at for debugging. +# +TEXT_BASE = 0x40000000 + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR) diff --git a/board/tqm8260/config.mk b/board/tqm8260/config.mk new file mode 100644 index 0000000..1fe9952 --- /dev/null +++ b/board/tqm8260/config.mk @@ -0,0 +1,34 @@ +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# TQM8260 boards +# + +# This should be equal to the CFG_FLASH_BASE define in config_TQM8260.h +# for the "final" configuration, with U-Boot in flash, or the address +# in RAM where U-Boot is loaded at for debugging. +# +TEXT_BASE = 0x40000000 + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR) diff --git a/common/fpga.c b/common/fpga.c new file mode 100644 index 0000000..c5975bc --- /dev/null +++ b/common/fpga.c @@ -0,0 +1,351 @@ +/* + * (C) Copyright 2002 + * Rich Ireland, Enterasys Networks, rireland@enterasys.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* + * Generic FPGA support + */ +#include /* core U-Boot definitions */ +#include /* xilinx specific definitions */ +#include /* altera specific definitions */ + +#if defined(CONFIG_FPGA) + +#if 0 +#define FPGA_DEBUG /* define FPGA_DEBUG to get debug messages */ +#endif + +/* Local definitions */ +#ifndef CONFIG_MAX_FPGA_DEVICES +#define CONFIG_MAX_FPGA_DEVICES 5 +#endif + +/* Enable/Disable debug console messages */ +#ifdef FPGA_DEBUG +#define PRINTF(fmt,args...) printf (fmt ,##args) +#else +#define PRINTF(fmt,args...) +#endif + +/* Local static data */ +static ulong relocation_offset = 0; +static int next_desc = FPGA_INVALID_DEVICE; +static fpga_desc desc_table[CONFIG_MAX_FPGA_DEVICES]; + +/* Local static functions */ +static const fpga_desc * const fpga_get_desc( int devnum ); +static const fpga_desc * const fpga_validate( int devnum, void *buf, + size_t bsize, char *fn ); +static int fpga_dev_info( int devnum ); + + +/* ------------------------------------------------------------------------- */ + +/* fpga_no_sup + * 'no support' message function + */ +static void fpga_no_sup( char *fn, char *msg ) +{ + if ( fn && msg ) { + printf( "%s: No support for %s. CONFIG_FPGA defined as 0x%x.\n", + fn, msg, CONFIG_FPGA ); + } else if ( msg ) { + printf( "No support for %s. CONFIG_FPGA defined as 0x%x.\n", + msg, CONFIG_FPGA ); + } else { + printf( "No FPGA suport! CONFIG_FPGA defined as 0x%x.\n", + CONFIG_FPGA ); + } +} + + +/* fpga_get_desc + * map a device number to a descriptor + */ +static const fpga_desc * const fpga_get_desc( int devnum ) +{ + fpga_desc *desc = (fpga_desc * )NULL; + + if (( devnum >= 0 ) && (devnum < next_desc )) { + desc = &desc_table[devnum]; + PRINTF( "%s: found fpga descriptor #%d @ 0x%p\n", + __FUNCTION__, devnum, desc ); + } + + return desc; +} + + +/* fpga_validate + * generic parameter checking code + */ +static const fpga_desc * const fpga_validate( int devnum, void *buf, + size_t bsize, char *fn ) +{ + const fpga_desc * const desc = fpga_get_desc( devnum ); + + if ( !desc ) { + printf( "%s: Invalid device number %d\n", fn, devnum ); + } + + if ( !buf ) { + printf( "%s: Null buffer.\n", fn ); + return (fpga_desc * const)NULL; + } + if ( !bsize ) { + printf( "%s: Null buffer size.\n", fn ); + return (fpga_desc * const)NULL; + } + + return desc; +} + + +/* fpga_dev_info + * generic multiplexing code + */ +static int fpga_dev_info( int devnum ) +{ + int ret_val = FPGA_FAIL; /* assume failure */ + const fpga_desc * const desc = fpga_get_desc( devnum ); + + if ( desc ) { + PRINTF( "%s: Device Descriptor @ 0x%p\n", + __FUNCTION__, desc->devdesc ); + + switch ( desc->devtype ) { + case fpga_xilinx: +#if CONFIG_FPGA & CFG_FPGA_XILINX + printf( "Xilinx Device\nDescriptor @ 0x%p\n", desc ); + ret_val = xilinx_info( desc->devdesc ); +#else + fpga_no_sup( __FUNCTION__, "Xilinx devices" ); +#endif + break; + case fpga_altera: +#if CONFIG_FPGA & CFG_FPGA_ALTERA + printf( "Altera Device\nDescriptor @ 0x%p\n", desc ); + ret_val = altera_info( desc->devdesc ); +#else + fpga_no_sup( __FUNCTION__, "Altera devices" ); +#endif + break; + default: + printf( "%s: Invalid or unsupported device type %d\n", + __FUNCTION__, desc->devtype ); + } + } else { + printf( "%s: Invalid device number %d\n", + __FUNCTION__, devnum ); + } + + return ret_val; +} + + +/* fpga_reloc + * generic multiplexing code + */ +int fpga_reloc( fpga_type devtype, void *desc, ulong reloc_off ) +{ + int ret_val = FPGA_FAIL; + + PRINTF( "%s: Relocating Device of type %d @ 0x%p with offset %lx\n", + __FUNCTION__, devtype, desc, reloc_off ); + + switch ( devtype ) { + case fpga_xilinx: +#if CONFIG_FPGA & CFG_FPGA_XILINX + ret_val = xilinx_reloc( desc, reloc_off ); +#else + fpga_no_sup( __FUNCTION__, "Xilinx devices" ); +#endif + break; + case fpga_altera: +#if CONFIG_FPGA & CFG_FPGA_ALTERA + ret_val = altera_reloc( desc, reloc_off ); +#else + fpga_no_sup( __FUNCTION__, "Altera devices" ); +#endif + break; + default: + printf( "%s: Invalid or unsupported device type %d\n", + __FUNCTION__, devtype ); + } + + return ret_val; +} + +/* ------------------------------------------------------------------------- */ +/* fgpa_init is usually called from misc_init_r() and MUST be called + * before any of the other fpga functions are used. + */ +void fpga_init( ulong reloc_off ) +{ + relocation_offset = reloc_off; + next_desc = 0; + memset( desc_table, 0, sizeof(desc_table)); + + PRINTF( "%s: CONFIG_FPGA = 0x%x\n", __FUNCTION__, CONFIG_FPGA ); +#if 0 + PRINTF( "%s: CFG_FPGA_XILINX = 0x%x\n", __FUNCTION__, CFG_FPGA_XILINX ); + PRINTF( "%s: CFG_FPGA_ALTERA = 0x%x\n", __FUNCTION__, CFG_FPGA_ALTERA ); +#endif +} + +/* fpga_count + * Basic interface function to get the current number of devices available. + */ +const int fpga_count( void ) +{ + return next_desc; +} + +/* fpga_add + * Attempts to relocate the device/board specific interface code + * to the proper RAM locations and adds the device descriptor to + * the device table. + */ +int fpga_add( fpga_type devtype, void *desc ) +{ + int devnum = FPGA_INVALID_DEVICE; + + if ( next_desc < 0 ) { + printf( "%s: FPGA support not initialized!\n", __FUNCTION__ ); + } else if (( devtype > fpga_min_type ) && ( devtype < fpga_undefined )) { + if ( desc ) { + if ( next_desc < CONFIG_MAX_FPGA_DEVICES ) { + if ( fpga_reloc( devtype, desc, relocation_offset ) + == FPGA_SUCCESS ) { + devnum = next_desc; + desc_table[next_desc].devtype = devtype; + desc_table[next_desc++].devdesc = desc; + } else { + printf( "%s: Unable to relocate device interface table!\n", + __FUNCTION__ ); + } + } else { + printf( "%s: Exceeded Max FPGA device count\n", __FUNCTION__ ); + } + } else { + printf( "%s: NULL device descriptor\n", __FUNCTION__ ); + } + } else { + printf( "%s: Unsupported FPGA type %d\n", __FUNCTION__, devtype ); + } + + return devnum; +} + +/* + * Generic multiplexing code + */ +int fpga_load( int devnum, void *buf, size_t bsize ) +{ + int ret_val = FPGA_FAIL; /* assume failure */ + const fpga_desc * const desc = fpga_validate( devnum, buf, bsize, __FUNCTION__ ); + + if ( desc ) { + switch ( desc->devtype ) { + case fpga_xilinx: +#if CONFIG_FPGA & CFG_FPGA_XILINX + ret_val = xilinx_load( desc->devdesc, buf, bsize ); +#else + fpga_no_sup( __FUNCTION__, "Xilinx devices" ); +#endif + break; + case fpga_altera: +#if CONFIG_FPGA & CFG_FPGA_ALTERA + ret_val = altera_load( desc->devdesc, buf, bsize ); +#else + fpga_no_sup( __FUNCTION__, "Altera devices" ); +#endif + break; + default: + printf( "%s: Invalid or unsupported device type %d\n", + __FUNCTION__, desc->devtype ); + } + } + + return ret_val; +} + +/* fpga_dump + * generic multiplexing code + */ +int fpga_dump( int devnum, void *buf, size_t bsize ) +{ + int ret_val = FPGA_FAIL; /* assume failure */ + const fpga_desc * const desc = fpga_validate( devnum, buf, bsize, __FUNCTION__ ); + + if ( desc ) { + switch ( desc->devtype ) { + case fpga_xilinx: +#if CONFIG_FPGA & CFG_FPGA_XILINX + ret_val = xilinx_dump( desc->devdesc, buf, bsize ); +#else + fpga_no_sup( __FUNCTION__, "Xilinx devices" ); +#endif + break; + case fpga_altera: +#if CONFIG_FPGA & CFG_FPGA_ALTERA + ret_val = altera_dump( desc->devdesc, buf, bsize ); +#else + fpga_no_sup( __FUNCTION__, "Altera devices" ); +#endif + break; + default: + printf( "%s: Invalid or unsupported device type %d\n", + __FUNCTION__, desc->devtype ); + } + } + + return ret_val; +} + + +/* fpga_info + * front end to fpga_dev_info. If devnum is invalid, report on all + * available devices. + */ +int fpga_info( int devnum ) +{ + if ( devnum == FPGA_INVALID_DEVICE ) { + if ( next_desc > 0 ) { + int dev; + + for ( dev = 0; dev < next_desc; dev++ ) { + fpga_dev_info( dev ); + } + return FPGA_SUCCESS; + } else { + printf( "%s: No FPGA devices available.\n", __FUNCTION__ ); + return FPGA_FAIL; + } + } + else return fpga_dev_info( devnum ); +} + +/* ------------------------------------------------------------------------- */ + +#endif /* CONFIG_FPGA */ diff --git a/common/spartan2.c b/common/spartan2.c new file mode 100644 index 0000000..9ac1e13 --- /dev/null +++ b/common/spartan2.c @@ -0,0 +1,470 @@ +/* + * (C) Copyright 2002 + * Rich Ireland, Enterasys Networks, rireland@enterasys.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include /* core U-Boot definitions */ +#include /* Spartan-II device family */ + +#if (CONFIG_FPGA & (CFG_XILINX | CFG_SPARTAN2)) + +/* Define FPGA_DEBUG to get debug printf's */ +#ifdef FPGA_DEBUG +#define PRINTF(fmt,args...) printf (fmt ,##args) +#else +#define PRINTF(fmt,args...) +#endif + +#undef CFG_FPGA_CHECK_BUSY +#define CFG_FPGA_PROG_FEEDBACK + +/* Note: The assumption is that we cannot possibly run fast enough to + * overrun the device (the Slave Parallel mode can free run at 50MHz). + * If there is a need to operate slower, define CONFIG_FPGA_DELAY in + * the board config file to slow things down. + */ +#ifndef CONFIG_FPGA_DELAY +#define CONFIG_FPGA_DELAY() +#endif + +#ifndef CFG_FPGA_WAIT +#define CFG_FPGA_WAIT 10 +#endif + +static int Spartan2_sp_load( Xilinx_desc *desc, void *buf, size_t bsize ); +static int Spartan2_sp_dump( Xilinx_desc *desc, void *buf, size_t bsize ); +/* static int Spartan2_sp_info( Xilinx_desc *desc ); */ +static int Spartan2_sp_reloc( Xilinx_desc *desc, ulong reloc_offset ); + +static int Spartan2_ss_load( Xilinx_desc *desc, void *buf, size_t bsize ); +static int Spartan2_ss_dump( Xilinx_desc *desc, void *buf, size_t bsize ); +/* static int Spartan2_ss_info( Xilinx_desc *desc ); */ +static int Spartan2_ss_reloc( Xilinx_desc *desc, ulong reloc_offset ); + +/* ------------------------------------------------------------------------- */ +/* Spartan-II Generic Implementation */ +int Spartan2_load (Xilinx_desc * desc, void *buf, size_t bsize) +{ + int ret_val = FPGA_FAIL; + + switch (desc->iface) { + case slave_serial: + PRINTF ("%s: Launching Slave Serial Load\n", __FUNCTION__); + ret_val = Spartan2_ss_load (desc, buf, bsize); + break; + + case slave_parallel: + PRINTF ("%s: Launching Slave Parallel Load\n", __FUNCTION__); + ret_val = Spartan2_sp_load (desc, buf, bsize); + break; + + default: + printf ("%s: Unsupported interface type, %d\n", + __FUNCTION__, desc->iface); + } + + return ret_val; +} + +int Spartan2_dump (Xilinx_desc * desc, void *buf, size_t bsize) +{ + int ret_val = FPGA_FAIL; + + switch (desc->iface) { + case slave_serial: + PRINTF ("%s: Launching Slave Serial Dump\n", __FUNCTION__); + ret_val = Spartan2_ss_dump (desc, buf, bsize); + break; + + case slave_parallel: + PRINTF ("%s: Launching Slave Parallel Dump\n", __FUNCTION__); + ret_val = Spartan2_sp_dump (desc, buf, bsize); + break; + + default: + printf ("%s: Unsupported interface type, %d\n", + __FUNCTION__, desc->iface); + } + + return ret_val; +} + +int Spartan2_info( Xilinx_desc *desc ) +{ + return FPGA_SUCCESS; +} + + +int Spartan2_reloc (Xilinx_desc * desc, ulong reloc_offset) +{ + int ret_val = FPGA_FAIL; /* assume a failure */ + + if (desc->family != Xilinx_Spartan2) { + printf ("%s: Unsupported family type, %d\n", + __FUNCTION__, desc->family); + return FPGA_FAIL; + } else + switch (desc->iface) { + case slave_serial: + ret_val = Spartan2_ss_reloc (desc, reloc_offset); + break; + + case slave_parallel: + ret_val = Spartan2_sp_reloc (desc, reloc_offset); + break; + + default: + printf ("%s: Unsupported interface type, %d\n", + __FUNCTION__, desc->iface); + } + + return ret_val; +} + + +/* ------------------------------------------------------------------------- */ +/* Spartan-II Slave Parallel Generic Implementation */ + +static int Spartan2_sp_load (Xilinx_desc * desc, void *buf, size_t bsize) +{ + int ret_val = FPGA_FAIL; /* assume the worst */ + Xilinx_Spartan2_Slave_Parallel_fns *fn = desc->iface_fns; + + PRINTF ("%s: start with interface functions @ 0x%p\n", + __FUNCTION__, fn); + + if (fn) { + size_t bytecount = 0; + unsigned char *data = (unsigned char *) buf; + int cookie = desc->cookie; /* make a local copy */ + unsigned long ts; /* timestamp */ + + PRINTF ("%s: Function Table:\n" + "ptr:\t0x%p\n" + "struct: 0x%p\n" + "pre: 0x%p\n" + "pgm:\t0x%p\n" + "init:\t0x%p\n" + "err:\t0x%p\n" + "clk:\t0x%p\n" + "cs:\t0x%p\n" + "wr:\t0x%p\n" + "read data:\t0x%p\n" + "write data:\t0x%p\n" + "busy:\t0x%p\n" + "abort:\t0x%p\n", + "post:\t0x%p\n\n", + __FUNCTION__, &fn, fn, fn->pre, fn->pgm, fn->init, fn->err, + fn->clk, fn->cs, fn->wr, fn->rdata, fn->wdata, fn->busy, + fn->abort, fn->post); + + /* + * This code is designed to emulate the "Express Style" + * Continuous Data Loading in Slave Parallel Mode for + * the Spartan-II Family. + */ +#ifdef CFG_FPGA_PROG_FEEDBACK + printf ("Loading FPGA Device %d...\n", cookie); +#endif + /* + * Run the pre configuration function if there is one. + */ + if (*fn->pre) { + (*fn->pre) (cookie); + } + + /* Establish the initial state */ + (*fn->pgm) (TRUE, TRUE, cookie); /* Assert the program, commit */ + + /* Get ready for the burn */ + CONFIG_FPGA_DELAY (); + (*fn->pgm) (FALSE, TRUE, cookie); /* Deassert the program, commit */ + + ts = get_timer (0); /* get current time */ + /* Now wait for INIT and BUSY to go high */ + do { + CONFIG_FPGA_DELAY (); + if (get_timer (ts) > CFG_FPGA_WAIT) { /* check the time */ + puts ("** Timeout waiting for INIT to clear.\n"); + (*fn->abort) (cookie); /* abort the burn */ + return FPGA_FAIL; + } + } while ((*fn->init) (cookie) && (*fn->busy) (cookie)); + + (*fn->wr) (TRUE, TRUE, cookie); /* Assert write, commit */ + (*fn->cs) (TRUE, TRUE, cookie); /* Assert chip select, commit */ + (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */ + + /* Load the data */ + while (bytecount < bsize) { + /* XXX - do we check for an Ctrl-C press in here ??? */ + /* XXX - Check the error bit? */ + + (*fn->wdata) (data[bytecount++], TRUE, cookie); /* write the data */ + CONFIG_FPGA_DELAY (); + (*fn->clk) (FALSE, TRUE, cookie); /* Deassert the clock pin */ + CONFIG_FPGA_DELAY (); + (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */ + +#ifdef CFG_FPGA_CHECK_BUSY + ts = get_timer (0); /* get current time */ + while ((*fn->busy) (cookie)) { + /* XXX - we should have a check in here somewhere to + * make sure we aren't busy forever... */ + + CONFIG_FPGA_DELAY (); + (*fn->clk) (FALSE, TRUE, cookie); /* Deassert the clock pin */ + CONFIG_FPGA_DELAY (); + (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */ + + if (get_timer (ts) > CFG_FPGA_WAIT) { /* check the time */ + puts ("** Timeout waiting for BUSY to clear.\n"); + (*fn->abort) (cookie); /* abort the burn */ + return FPGA_FAIL; + } + } +#endif + +#ifdef CFG_FPGA_PROG_FEEDBACK + if (bytecount % (bsize / 40) == 0) + putc ('.'); /* let them know we are alive */ +#endif + } + + CONFIG_FPGA_DELAY (); + (*fn->cs) (FALSE, TRUE, cookie); /* Deassert the chip select */ + (*fn->wr) (FALSE, TRUE, cookie); /* Deassert the write pin */ + +#ifdef CFG_FPGA_PROG_FEEDBACK + putc ('\n'); /* terminate the dotted line */ +#endif + + /* now check for done signal */ + ts = get_timer (0); /* get current time */ + ret_val = FPGA_SUCCESS; + while ((*fn->done) (cookie) == FPGA_FAIL) { + /* XXX - we should have a check in here somewhere to + * make sure we aren't busy forever... */ + + CONFIG_FPGA_DELAY (); + (*fn->clk) (FALSE, TRUE, cookie); /* Deassert the clock pin */ + CONFIG_FPGA_DELAY (); + (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */ + + if (get_timer (ts) > CFG_FPGA_WAIT) { /* check the time */ + puts ("** Timeout waiting for DONE to clear.\n"); + (*fn->abort) (cookie); /* abort the burn */ + ret_val = FPGA_FAIL; + break; + } + } + + if (ret_val == FPGA_SUCCESS) { +#ifdef CFG_FPGA_PROG_FEEDBACK + puts ("Done.\n"); +#endif + } + /* + * Run the post configuration function if there is one. + */ + if (*fn->post) { + (*fn->post) (cookie); + } + + else { +#ifdef CFG_FPGA_PROG_FEEDBACK + puts ("Fail.\n"); +#endif + } + + } else { + printf ("%s: NULL Interface function table!\n", __FUNCTION__); + } + + return ret_val; +} + +static int Spartan2_sp_dump (Xilinx_desc * desc, void *buf, size_t bsize) +{ + int ret_val = FPGA_FAIL; /* assume the worst */ + Xilinx_Spartan2_Slave_Parallel_fns *fn = desc->iface_fns; + + if (fn) { + unsigned char *data = (unsigned char *) buf; + size_t bytecount = 0; + int cookie = desc->cookie; /* make a local copy */ + + printf ("Starting Dump of FPGA Device %d...\n", cookie); + + (*fn->cs) (TRUE, TRUE, cookie); /* Assert chip select, commit */ + (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */ + + /* dump the data */ + while (bytecount < bsize) { + /* XXX - do we check for an Ctrl-C press in here ??? */ + + (*fn->clk) (FALSE, TRUE, cookie); /* Deassert the clock pin */ + (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */ + (*fn->rdata) (&(data[bytecount++]), cookie); /* read the data */ +#ifdef CFG_FPGA_PROG_FEEDBACK + if (bytecount % (bsize / 40) == 0) + putc ('.'); /* let them know we are alive */ +#endif + } + + (*fn->cs) (FALSE, FALSE, cookie); /* Deassert the chip select */ + (*fn->clk) (FALSE, TRUE, cookie); /* Deassert the clock pin */ + (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */ + +#ifdef CFG_FPGA_PROG_FEEDBACK + putc ('\n'); /* terminate the dotted line */ +#endif + puts ("Done.\n"); + + /* XXX - checksum the data? */ + } else { + printf ("%s: NULL Interface function table!\n", __FUNCTION__); + } + + return ret_val; +} + + +static int Spartan2_sp_reloc (Xilinx_desc * desc, ulong reloc_offset) +{ + int ret_val = FPGA_FAIL; /* assume the worst */ + Xilinx_Spartan2_Slave_Parallel_fns *fn_r, *fn = + (Xilinx_Spartan2_Slave_Parallel_fns *) (desc->iface_fns); + + if (fn) { + ulong addr; + + /* Get the relocated table address */ + addr = (ulong) fn + reloc_offset; + fn_r = (Xilinx_Spartan2_Slave_Parallel_fns *) addr; + + if (!fn_r->relocated) { + + if (memcmp (fn_r, fn, + sizeof (Xilinx_Spartan2_Slave_Parallel_fns)) + == 0) { + /* good copy of the table, fix the descriptor pointer */ + desc->iface_fns = fn_r; + } else { + PRINTF ("%s: Invalid function table at 0x%p\n", + __FUNCTION__, fn_r); + return FPGA_FAIL; + } + + PRINTF ("%s: Relocating descriptor at 0x%p\n", __FUNCTION__, + desc); + + addr = (ulong) (fn->pre) + reloc_offset; + fn_r->pre = (Xilinx_pre_fn) addr; + + addr = (ulong) (fn->pgm) + reloc_offset; + fn_r->pgm = (Xilinx_pgm_fn) addr; + + addr = (ulong) (fn->init) + reloc_offset; + fn_r->init = (Xilinx_init_fn) addr; + + addr = (ulong) (fn->done) + reloc_offset; + fn_r->done = (Xilinx_done_fn) addr; + + addr = (ulong) (fn->clk) + reloc_offset; + fn_r->clk = (Xilinx_clk_fn) addr; + + addr = (ulong) (fn->err) + reloc_offset; + fn_r->err = (Xilinx_err_fn) addr; + + addr = (ulong) (fn->cs) + reloc_offset; + fn_r->cs = (Xilinx_cs_fn) addr; + + addr = (ulong) (fn->wr) + reloc_offset; + fn_r->wr = (Xilinx_wr_fn) addr; + + addr = (ulong) (fn->rdata) + reloc_offset; + fn_r->rdata = (Xilinx_rdata_fn) addr; + + addr = (ulong) (fn->wdata) + reloc_offset; + fn_r->wdata = (Xilinx_wdata_fn) addr; + + addr = (ulong) (fn->busy) + reloc_offset; + fn_r->busy = (Xilinx_busy_fn) addr; + + addr = (ulong) (fn->abort) + reloc_offset; + fn_r->abort = (Xilinx_abort_fn) addr; + + addr = (ulong) (fn->post) + reloc_offset; + fn_r->post = (Xilinx_post_fn) addr; + + fn_r->relocated = TRUE; + + } else { + /* this table has already been moved */ + /* XXX - should check to see if the descriptor is correct */ + desc->iface_fns = fn_r; + } + + ret_val = FPGA_SUCCESS; + } else { + printf ("%s: NULL Interface function table!\n", __FUNCTION__); + } + + return ret_val; + +} + +/* ------------------------------------------------------------------------- */ + +static int Spartan2_ss_load (Xilinx_desc * desc, void *buf, size_t bsize) +{ + printf ("%s: Slave Serial Loading is still unsupported\n", + __FUNCTION__); + return FPGA_FAIL; +} + +static int Spartan2_ss_dump (Xilinx_desc * desc, void *buf, size_t bsize) +{ + printf ("%s: Slave Serial Dumping is still unsupported\n", + __FUNCTION__); + return FPGA_FAIL; +} + +static int Spartan2_ss_reloc (Xilinx_desc * desc, ulong reloc_offset) +{ + int ret_val = FPGA_FAIL; /* assume the worst */ + Xilinx_Spartan2_Slave_Serial_fns *fn = + (Xilinx_Spartan2_Slave_Serial_fns *) (desc->iface_fns); + + if (fn) { + printf ("%s: Slave Serial Loading is still unsupported\n", + __FUNCTION__); + } else { + printf ("%s: NULL Interface function table!\n", __FUNCTION__); + } + + return ret_val; + +} + +#endif diff --git a/config.mk b/config.mk new file mode 100644 index 0000000..ef3c703 --- /dev/null +++ b/config.mk @@ -0,0 +1,156 @@ +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +######################################################################### + +# +# When cross-compiling on NetBSD, we have to define __PPC__ or else we +# will pick up a va_list declaration that is incompatible with the +# actual argument lists emitted by the compiler. +# +# [Tested on NetBSD/i386 1.5 + cross-powerpc-netbsd-1.3] + +ifeq ($(ARCH),ppc) +ifeq ($(CROSS_COMPILE),powerpc-netbsd-) +PLATFORM_CPPFLAGS+= -D__PPC__ +endif +ifeq ($(CROSS_COMPILE),powerpc-openbsd-) +PLATFORM_CPPFLAGS+= -D__PPC__ +endif +endif + +ifeq ($(ARCH),arm) +ifeq ($(CROSS_COMPILE),powerpc-netbsd-) +PLATFORM_CPPFLAGS+= -D__ARM__ +endif +ifeq ($(CROSS_COMPILE),powerpc-openbsd-) +PLATFORM_CPPFLAGS+= -D__ARM__ +endif +endif + +ifdef ARCH +sinclude $(TOPDIR)/$(ARCH)_config.mk # include architecture dependend rules +endif +ifdef CPU +sinclude $(TOPDIR)/cpu/$(CPU)/config.mk # include CPU specific rules +endif +ifdef VENDOR +BOARDDIR = $(VENDOR)/$(BOARD) +else +BOARDDIR = $(BOARD) +endif +ifdef BOARD +sinclude $(TOPDIR)/board/$(BOARDDIR)/config.mk # include board specific rules +endif + +######################################################################### + +CONFIG_SHELL := $(shell if [ -x "$$BASH" ]; then echo $$BASH; \ + else if [ -x /bin/bash ]; then echo /bin/bash; \ + else echo sh; fi ; fi) + +ifeq ($(HOSTOS)-$(HOSTARCH),darwin-ppc) +HOSTCC = cc +else +HOSTCC = gcc +endif +HOSTCFLAGS = -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer +HOSTSTRIP = strip + +######################################################################### + +# +# Include the make variables (CC, etc...) +# +AS = $(CROSS_COMPILE)as +LD = $(CROSS_COMPILE)ld +CC = $(CROSS_COMPILE)gcc +CPP = $(CC) -E +AR = $(CROSS_COMPILE)ar +NM = $(CROSS_COMPILE)nm +STRIP = $(CROSS_COMPILE)strip +OBJCOPY = $(CROSS_COMPILE)objcopy +OBJDUMP = $(CROSS_COMPILE)objdump +RANLIB = $(CROSS_COMPILE)RANLIB + +RELFLAGS= $(PLATFORM_RELFLAGS) +DBGFLAGS= -g #-DDEBUG +OPTFLAGS= -Os #-fomit-frame-pointer +#LDSCRIPT := board/$(BOARDDIR)/u-boot.lds.debug +LDSCRIPT := $(TOPDIR)/board/$(BOARDDIR)/u-boot.lds +OBJCFLAGS := --gap-fill=0xff + +CPPFLAGS := $(DBGFLAGS) $(OPTFLAGS) $(RELFLAGS) \ + -D__KERNEL__ -DTEXT_BASE=$(TEXT_BASE) \ + -I$(TOPDIR)/include \ + -fno-builtin \ + -pipe $(PLATFORM_CPPFLAGS) + +ifdef BUILD_TAG +CFLAGS := $(CPPFLAGS) -Wall -Wstrict-prototypes \ + -DBUILD_TAG='"$(BUILD_TAG)"' +else +CFLAGS := $(CPPFLAGS) -Wall -Wstrict-prototypes +endif + +AFLAGS_DEBUG := -Wa,-gstabs +AFLAGS := $(AFLAGS_DEBUG) -D__ASSEMBLY__ $(CPPFLAGS) + +LDFLAGS += -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) + +# Location of a usable BFD library, where we define "usable" as +# "built for ${HOST}, supports ${TARGET}". Sensible values are +# - When cross-compiling: the root of the cross-environment +# - Linux/ppc (native): /usr +# - NetBSD/ppc (native): you lose ... (must extract these from the +# binutils build directory, plus the native and U-Boot include +# files don't like each other) +# +# So far, this is used only by tools/gdb/Makefile. + +ifeq ($(HOSTOS)-$(HOSTARCH),darwin-ppc) +BFD_ROOT_DIR = /usr/local/tools +else +#BFD_ROOT_DIR = /LinuxPPC/CDK # Linux/i386 +#BFD_ROOT_DIR = /usr/pkg/cross # NetBSD/i386 +#BFD_ROOT_DIR = /usr # native +BFD_ROOT_DIR = /opt/powerpc +endif + +######################################################################### + +export CONFIG_SHELL HPATH HOSTCC HOSTCFLAGS CROSS_COMPILE \ + AS LD CC CPP AR NM STRIP OBJCOPY OBJDUMP \ + MAKE +export TEXT_BASE PLATFORM_CPPFLAGS PLATFORM_RELFLAGS CPPFLAGS CFLAGS AFLAGS + +######################################################################### + +%.s: %.S + $(CPP) $(AFLAGS) -o $@ $(CURDIR)/$< +%.o: %.S + $(CC) $(AFLAGS) -c -o $@ $(CURDIR)/$< +%.o: %.c + $(CC) $(CFLAGS) -c -o $@ $< + +######################################################################### diff --git a/cpu/mpc824x/drivers/epic/epic.h b/cpu/mpc824x/drivers/epic/epic.h new file mode 100644 index 0000000..7751db2 --- /dev/null +++ b/cpu/mpc824x/drivers/epic/epic.h @@ -0,0 +1,160 @@ +/********************************************************************* + * mpc8240epic.h - EPIC module of the MPC8240 micro-controller + * + * Copyrigh 1999 Motorola Inc. + * + * Modification History: + * ===================== + * 01a,04Feb99,My Created. + * 15Nov200, robt -modified to use in U-Boot + * +*/ + +#ifndef __INCEPICh +#define __INCEPICh + +#define ULONG unsigned long +#define MAXVEC 20 +#define MAXIRQ 5 /* IRQs */ +#define EPIC_DIRECT_IRQ 0 /* Direct interrupt type */ + +/* EPIC register addresses */ + +#define EPIC_EUMBBAR 0x40000 /* EUMBBAR of EPIC */ +#define EPIC_FEATURES_REG (EPIC_EUMBBAR + 0x01000)/* Feature reporting */ +#define EPIC_GLOBAL_REG (EPIC_EUMBBAR + 0x01020)/* Global config. */ +#define EPIC_INT_CONF_REG (EPIC_EUMBBAR + 0x01030)/* Interrupt config. */ +#define EPIC_VENDOR_ID_REG (EPIC_EUMBBAR + 0x01080)/* Vendor id */ +#define EPIC_PROC_INIT_REG (EPIC_EUMBBAR + 0x01090)/* Processor init. */ +#define EPIC_SPUR_VEC_REG (EPIC_EUMBBAR + 0x010e0)/* Spurious vector */ +#define EPIC_TM_FREQ_REG (EPIC_EUMBBAR + 0x010f0)/* Timer Frequency */ + +#define EPIC_TM0_CUR_COUNT_REG (EPIC_EUMBBAR + 0x01100)/* Gbl TM0 Cur. Count*/ +#define EPIC_TM0_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01110)/* Gbl TM0 Base Count*/ +#define EPIC_TM0_VEC_REG (EPIC_EUMBBAR + 0x01120)/* Gbl TM0 Vector Pri*/ +#define EPIC_TM0_DES_REG (EPIC_EUMBBAR + 0x01130)/* Gbl TM0 Dest. */ + +#define EPIC_TM1_CUR_COUNT_REG (EPIC_EUMBBAR + 0x01140)/* Gbl TM1 Cur. Count*/ +#define EPIC_TM1_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01150)/* Gbl TM1 Base Count*/ +#define EPIC_TM1_VEC_REG (EPIC_EUMBBAR + 0x01160)/* Gbl TM1 Vector Pri*/ +#define EPIC_TM1_DES_REG (EPIC_EUMBBAR + 0x01170)/* Gbl TM1 Dest. */ + +#define EPIC_TM2_CUR_COUNT_REG (EPIC_EUMBBAR + 0x01180)/* Gbl TM2 Cur. Count*/ +#define EPIC_TM2_BASE_COUNT_REG (EPIC_EUMBBAR + 0x01190)/* Gbl TM2 Base Count*/ +#define EPIC_TM2_VEC_REG (EPIC_EUMBBAR + 0x011a0)/* Gbl TM2 Vector Pri*/ +#define EPIC_TM2_DES_REG (EPIC_EUMBBAR + 0x011b0)/* Gbl TM2 Dest */ + +#define EPIC_TM3_CUR_COUNT_REG (EPIC_EUMBBAR + 0x011c0)/* Gbl TM3 Cur. Count*/ +#define EPIC_TM3_BASE_COUNT_REG (EPIC_EUMBBAR + 0x011d0)/* Gbl TM3 Base Count*/ +#define EPIC_TM3_VEC_REG (EPIC_EUMBBAR + 0x011e0)/* Gbl TM3 Vector Pri*/ +#define EPIC_TM3_DES_REG (EPIC_EUMBBAR + 0x011f0)/* Gbl TM3 Dest. */ + +#define EPIC_EX_INT0_VEC_REG (EPIC_EUMBBAR + 0x10200)/* Ext. Int. Sr0 Des */ +#define EPIC_EX_INT0_DES_REG (EPIC_EUMBBAR + 0x10210)/* Ext. Int. Sr0 Vect*/ +#define EPIC_EX_INT1_VEC_REG (EPIC_EUMBBAR + 0x10220)/* Ext. Int. Sr1 Des */ +#define EPIC_EX_INT1_DES_REG (EPIC_EUMBBAR + 0x10230)/* Ext. Int. Sr1 Vect*/ +#define EPIC_EX_INT2_VEC_REG (EPIC_EUMBBAR + 0x10240)/* Ext. Int. Sr2 Des */ +#define EPIC_EX_INT2_DES_REG (EPIC_EUMBBAR + 0x10250)/* Ext. Int. Sr2 Vect*/ +#define EPIC_EX_INT3_VEC_REG (EPIC_EUMBBAR + 0x10260)/* Ext. Int. Sr3 Des */ +#define EPIC_EX_INT3_DES_REG (EPIC_EUMBBAR + 0x10270)/* Ext. Int. Sr3 Vect*/ +#define EPIC_EX_INT4_VEC_REG (EPIC_EUMBBAR + 0x10280)/* Ext. Int. Sr4 Des */ +#define EPIC_EX_INT4_DES_REG (EPIC_EUMBBAR + 0x10290)/* Ext. Int. Sr4 Vect*/ + +#define EPIC_SR_INT0_VEC_REG (EPIC_EUMBBAR + 0x10200)/* Sr. Int. Sr0 Des */ +#define EPIC_SR_INT0_DES_REG (EPIC_EUMBBAR + 0x10210)/* Sr. Int. Sr0 Vect */ +#define EPIC_SR_INT1_VEC_REG (EPIC_EUMBBAR + 0x10220)/* Sr. Int. Sr1 Des */ +#define EPIC_SR_INT1_DES_REG (EPIC_EUMBBAR + 0x10230)/* Sr. Int. Sr1 Vect.*/ +#define EPIC_SR_INT2_VEC_REG (EPIC_EUMBBAR + 0x10240)/* Sr. Int. Sr2 Des */ +#define EPIC_SR_INT2_DES_REG (EPIC_EUMBBAR + 0x10250)/* Sr. Int. Sr2 Vect.*/ +#define EPIC_SR_INT3_VEC_REG (EPIC_EUMBBAR + 0x10260)/* Sr. Int. Sr3 Des */ +#define EPIC_SR_INT3_DES_REG (EPIC_EUMBBAR + 0x10270)/* Sr. Int. Sr3 Vect.*/ +#define EPIC_SR_INT4_VEC_REG (EPIC_EUMBBAR + 0x10280)/* Sr. Int. Sr4 Des */ +#define EPIC_SR_INT4_DES_REG (EPIC_EUMBBAR + 0x10290)/* Sr. Int. Sr4 Vect.*/ + +#define EPIC_SR_INT5_VEC_REG (EPIC_EUMBBAR + 0x102a0)/* Sr. Int. Sr5 Des */ +#define EPIC_SR_INT5_DES_REG (EPIC_EUMBBAR + 0x102b0)/* Sr. Int. Sr5 Vect.*/ +#define EPIC_SR_INT6_VEC_REG (EPIC_EUMBBAR + 0x102c0)/* Sr. Int. Sr6 Des */ +#define EPIC_SR_INT6_DES_REG (EPIC_EUMBBAR + 0x102d0)/* Sr. Int. Sr6 Vect.*/ +#define EPIC_SR_INT7_VEC_REG (EPIC_EUMBBAR + 0x102e0)/* Sr. Int. Sr7 Des */ +#define EPIC_SR_INT7_DES_REG (EPIC_EUMBBAR + 0x102f0)/* Sr. Int. Sr7 Vect.*/ +#define EPIC_SR_INT8_VEC_REG (EPIC_EUMBBAR + 0x10300)/* Sr. Int. Sr8 Des */ +#define EPIC_SR_INT8_DES_REG (EPIC_EUMBBAR + 0x10310)/* Sr. Int. Sr8 Vect.*/ +#define EPIC_SR_INT9_VEC_REG (EPIC_EUMBBAR + 0x10320)/* Sr. Int. Sr9 Des */ +#define EPIC_SR_INT9_DES_REG (EPIC_EUMBBAR + 0x10330)/* Sr. Int. Sr9 Vect.*/ + +#define EPIC_SR_INT10_VEC_REG (EPIC_EUMBBAR + 0x10340)/* Sr. Int. Sr10 Des */ +#define EPIC_SR_INT10_DES_REG (EPIC_EUMBBAR + 0x10350)/* Sr. Int. Sr10 Vect*/ +#define EPIC_SR_INT11_VEC_REG (EPIC_EUMBBAR + 0x10360)/* Sr. Int. Sr11 Des */ +#define EPIC_SR_INT11_DES_REG (EPIC_EUMBBAR + 0x10370)/* Sr. Int. Sr11 Vect*/ +#define EPIC_SR_INT12_VEC_REG (EPIC_EUMBBAR + 0x10380)/* Sr. Int. Sr12 Des */ +#define EPIC_SR_INT12_DES_REG (EPIC_EUMBBAR + 0x10390)/* Sr. Int. Sr12 Vect*/ +#define EPIC_SR_INT13_VEC_REG (EPIC_EUMBBAR + 0x103a0)/* Sr. Int. Sr13 Des */ +#define EPIC_SR_INT13_DES_REG (EPIC_EUMBBAR + 0x103b0)/* Sr. Int. Sr13 Vect*/ +#define EPIC_SR_INT14_VEC_REG (EPIC_EUMBBAR + 0x103c0)/* Sr. Int. Sr14 Des */ +#define EPIC_SR_INT14_DES_REG (EPIC_EUMBBAR + 0x103d0)/* Sr. Int. Sr14 Vect*/ +#define EPIC_SR_INT15_VEC_REG (EPIC_EUMBBAR + 0x103e0)/* Sr. Int. Sr15 Des */ +#define EPIC_SR_INT15_DES_REG (EPIC_EUMBBAR + 0x103f0)/* Sr. Int. Sr15 Vect*/ + +#define EPIC_I2C_INT_VEC_REG (EPIC_EUMBBAR + 0x11020)/* I2C Int. Vect Pri.*/ +#define EPIC_I2C_INT_DES_REG (EPIC_EUMBBAR + 0x11030)/* I2C Int. Dest */ +#define EPIC_DMA0_INT_VEC_REG (EPIC_EUMBBAR + 0x11040)/* DMA0 Int. Vect Pri*/ +#define EPIC_DMA0_INT_DES_REG (EPIC_EUMBBAR + 0x11050)/* DMA0 Int. Dest */ +#define EPIC_DMA1_INT_VEC_REG (EPIC_EUMBBAR + 0x11060)/* DMA1 Int. Vect Pri*/ +#define EPIC_DMA1_INT_DES_REG (EPIC_EUMBBAR + 0x11070)/* DMA1 Int. Dest */ +#define EPIC_MSG_INT_VEC_REG (EPIC_EUMBBAR + 0x110c0)/* Msg Int. Vect Pri*/ +#define EPIC_MSG_INT_DES_REG (EPIC_EUMBBAR + 0x110d0)/* Msg Int. Dest */ + +#define EPIC_PROC_CTASK_PRI_REG (EPIC_EUMBBAR + 0x20080)/* Proc. current task*/ +#define EPIC_PROC_INT_ACK_REG (EPIC_EUMBBAR + 0x200a0)/* Int. acknowledge */ +#define EPIC_PROC_EOI_REG (EPIC_EUMBBAR + 0x200b0)/* End of interrupt */ + +/* Error code */ + +#define OK 0 +#define ERROR -1 + +/* function prototypes */ + +void epicVendorId( unsigned int *step, + unsigned int *devId, + unsigned int *venId + ); +void epicFeatures( unsigned int *noIRQs, + unsigned int *noCPUs, + unsigned int *VerId ); +extern void epicInit( unsigned int IRQType, unsigned int clkRatio); +ULONG sysEUMBBARRead ( ULONG regNum ); +void sysEUMBBARWrite ( ULONG regNum, ULONG regVal); +extern void epicTmFrequencySet( unsigned int frq ); +extern unsigned int epicTmFrequencyGet(void); +extern unsigned int epicTmBaseSet( ULONG srcAddr, + unsigned int cnt, + unsigned int inhibit ); +extern unsigned int epicTmBaseGet ( ULONG srcAddr, unsigned int *val ); +extern unsigned int epicTmCountGet( ULONG srcAddr, unsigned int *val ); +extern unsigned int epicTmInhibit( unsigned int timer ); +extern unsigned int epicTmEnable( ULONG srcAdr ); +extern void CoreExtIntEnable(void); /* Enable 603e external interrupts */ +extern void CoreExtIntDisable(void); /* Disable 603e external interrupts */ +extern unsigned char epicIntTaskGet(void); +extern void epicIntTaskSet( unsigned char val ); +extern unsigned int epicIntAck(void); +extern void epicSprSet( unsigned int eumbbar, unsigned char ); +extern void epicConfigGet( unsigned int *clkRatio, + unsigned int *serEnable ); +extern void SrcVecTableInit(void); +extern unsigned int epicModeGet(void); +extern void epicIntEnable(int Vect); +extern void epicIntDisable(int Vect); +extern int epicIntSourceConfig(int Vect, int Polarity, int Sense, int Prio); +extern unsigned int epicIntAck(void); +extern void epicEOI(void); +extern int epicCurTaskPrioSet(int Vect); + +struct SrcVecTable + { + ULONG srcAddr; + char srcName[40]; + }; + +#endif /* EPIC_H */ diff --git a/doc/README.TQM8260 b/doc/README.TQM8260 new file mode 100644 index 0000000..7e03010 --- /dev/null +++ b/doc/README.TQM8260 @@ -0,0 +1,415 @@ + +This file contains basic information on the port of U-Boot to TQM8260. +All the changes fit in the common U-Boot infrastructure, providing a +new TQM8260-specific entry in makefiles. To build U-Boot for TQM8260, +type "make TQM8260_config", edit the "include/config_TQM8260.h" file +if necessary, then type "make". + + +Common file modifications: +-------------------------- + +The following common files have been modified by this project: +(starting from the ppcboot-0.9.3/ directory) + +MAKEALL - TQM8260 entry added +Makefile - TQM8260_config entry added +cpu/mpc8260/Makefile - soft_i2c.o module added +cpu/mpc8260/ether_scc.c - TQM8260-specific definitions added, an obvious + bug fixed (fcr -> scr) +cpu/mpc8260/ether_fcc.c - TQM8260-specific definitions added +include/flash.h - added definitions for the AM29LV640D Flash chip + + +New files: +---------- + +The following new files have been added by this project: +(starting from the ppcboot-0.9.3/ directory) + +board/tqm8260/ - board-specific directory +board/tqm8260/Makefile - board-specific makefile +board/tqm8260/config.mk - config file +board/tqm8260/flash.c - flash driver (for AM29LV640D) +board/tqm8260/ppcboot.lds - linker script +board/tqm8260/tqm8260.c - ioport and memory initialization +cpu/mpc8260/soft_i2c.c - software i2c EEPROM driver +include/config_TQM8260.h - main configuration file + + +New configuration options: +-------------------------- + +CONFIG_TQM8260 + + Main board-specific option (should be defined for TQM8260). + +CONFIG_82xx_CONS_SMC1 + + If defined, SMC1 will be used as the console + +CONFIG_82xx_CONS_SMC2 + + If defined, SMC2 will be used as the console + +CFG_INIT_LOCAL_SDRAM + + If defined, the SDRAM on the local bus will be initialized and + mapped at BR2. + + +Acceptance criteria tests: +-------------------------- + +The following tests have been conducted to validate the port of U-Boot +to TQM8260: + +1. Operation on serial console: + +With the CONFIG_82xx_CONS_SMC1 option defined in the main configuration file, +the U-Boot output appeared on the serial terminal connected to COM1 as +follows: + +------------------------------------------------------------------------------ +=> help +go - start application at address 'addr' +run - run commands in an environment variable +bootm - boot application image from memory +bootp - boot image via network using BootP/TFTP protocol +tftpboot- boot image via network using TFTP protocol + and env variables ipaddr and serverip +rarpboot- boot image via network using RARP/TFTP protocol +bootd - boot default, i.e., run 'bootcmd' +loads - load S-Record file over serial line +loadb - load binary file over serial line (kermit mode) +md - memory display +mm - memory modify (auto-incrementing) +nm - memory modify (constant address) +mw - memory write (fill) +cp - memory copy +cmp - memory compare +crc32 - checksum calculation +base - print or set address offset +printenv- print environment variables +setenv - set environment variables +saveenv - save environment variables to persistent storage +protect - enable or disable FLASH write protection +erase - erase FLASH memory +flinfo - print FLASH memory information +bdinfo - print Board Info structure +iminfo - print header information for application image +coninfo - print console devices and informations +eeprom - EEPROM sub-system +loop - infinite loop on address range +mtest - simple RAM test +icache - enable or disable instruction cache +dcache - enable or disable data cache +reset - Perform RESET of the CPU +echo - echo args to console +version - print monitor version +help - print online help +? - alias for 'help' +=> +------------------------------------------------------------------------------ + + +2. Flash driver operation + +The following sequence was performed to test the "flinfo" command: + +------------------------------------------------------------------------------ +=> flinfo + +Bank # 1: AMD 29LV640D (64 M, uniform sector) + Size: 32 MB in 128 Sectors + Sector Start Addresses: + 40000000 40040000 (RO) 40080000 400C0000 40100000 + 40140000 40180000 401C0000 40200000 40240000 + 40280000 402C0000 40300000 40340000 40380000 + 403C0000 40400000 40440000 40480000 404C0000 + 40500000 40540000 40580000 405C0000 40600000 + 40640000 40680000 406C0000 40700000 40740000 + 40780000 407C0000 40800000 40840000 40880000 + 408C0000 40900000 40940000 40980000 409C0000 + 40A00000 40A40000 40A80000 40AC0000 40B00000 + 40B40000 40B80000 40BC0000 40C00000 40C40000 + 40C80000 40CC0000 40D00000 40D40000 40D80000 + 40DC0000 40E00000 40E40000 40E80000 40EC0000 + 40F00000 40F40000 40F80000 40FC0000 41000000 + 41040000 41080000 410C0000 41100000 41140000 + 41180000 411C0000 41200000 41240000 41280000 + 412C0000 41300000 41340000 41380000 413C0000 + 41400000 41440000 41480000 414C0000 41500000 + 41540000 41580000 415C0000 41600000 41640000 + 41680000 416C0000 41700000 41740000 41780000 + 417C0000 41800000 41840000 41880000 418C0000 + 41900000 41940000 41980000 419C0000 41A00000 + 41A40000 41A80000 41AC0000 41B00000 41B40000 + 41B80000 41BC0000 41C00000 41C40000 41C80000 + 41CC0000 41D00000 41D40000 41D80000 41DC0000 + 41E00000 41E40000 41E80000 41EC0000 41F00000 + 41F40000 41F80000 41FC0000 +=> +------------------------------------------------------------------------------ + + +The following sequence was performed to test the erase command: + +------------------------------------------------------------------------------ +=> cp 0 40080000 10 +Copy to Flash... done +=> erase 40080000 400bffff +Erase Flash from 0x40080000 to 0x400bffff +.. done +Erased 1 sectors +=> md 40080000 +40080000: ffffffff ffffffff ffffffff ffffffff ................ +40080010: ffffffff ffffffff ffffffff ffffffff ................ +40080020: ffffffff ffffffff ffffffff ffffffff ................ +40080030: ffffffff ffffffff ffffffff ffffffff ................ +40080040: ffffffff ffffffff ffffffff ffffffff ................ +40080050: ffffffff ffffffff ffffffff ffffffff ................ +40080060: ffffffff ffffffff ffffffff ffffffff ................ +40080070: ffffffff ffffffff ffffffff ffffffff ................ +40080080: ffffffff ffffffff ffffffff ffffffff ................ +40080090: ffffffff ffffffff ffffffff ffffffff ................ +400800a0: ffffffff ffffffff ffffffff ffffffff ................ +400800b0: ffffffff ffffffff ffffffff ffffffff ................ +400800c0: ffffffff ffffffff ffffffff ffffffff ................ +400800d0: ffffffff ffffffff ffffffff ffffffff ................ +400800e0: ffffffff ffffffff ffffffff ffffffff ................ +400800f0: ffffffff ffffffff ffffffff ffffffff ................ +=> cp 0 40080000 10 +Copy to Flash... done +=> erase 1:2 +Erase Flash Sectors 2-2 in Bank # 1 +.. done +=> md 40080000 +40080000: ffffffff ffffffff ffffffff ffffffff ................ +40080010: ffffffff ffffffff ffffffff ffffffff ................ +40080020: ffffffff ffffffff ffffffff ffffffff ................ +40080030: ffffffff ffffffff ffffffff ffffffff ................ +40080040: ffffffff ffffffff ffffffff ffffffff ................ +40080050: ffffffff ffffffff ffffffff ffffffff ................ +40080060: ffffffff ffffffff ffffffff ffffffff ................ +40080070: ffffffff ffffffff ffffffff ffffffff ................ +40080080: ffffffff ffffffff ffffffff ffffffff ................ +40080090: ffffffff ffffffff ffffffff ffffffff ................ +400800a0: ffffffff ffffffff ffffffff ffffffff ................ +400800b0: ffffffff ffffffff ffffffff ffffffff ................ +400800c0: ffffffff ffffffff ffffffff ffffffff ................ +400800d0: ffffffff ffffffff ffffffff ffffffff ................ +400800e0: ffffffff ffffffff ffffffff ffffffff ................ +400800f0: ffffffff ffffffff ffffffff ffffffff ................ +=> cp 0 40080000 10 +Copy to Flash... done +=> cp 0 400c0000 10 +Copy to Flash... done +=> erase 1:2-3 +Erase Flash Sectors 2-3 in Bank # 1 +... done +=> md 40080000 +40080000: ffffffff ffffffff ffffffff ffffffff ................ +40080010: ffffffff ffffffff ffffffff ffffffff ................ +40080020: ffffffff ffffffff ffffffff ffffffff ................ +40080030: ffffffff ffffffff ffffffff ffffffff ................ +40080040: ffffffff ffffffff ffffffff ffffffff ................ +40080050: ffffffff ffffffff ffffffff ffffffff ................ +40080060: ffffffff ffffffff ffffffff ffffffff ................ +40080070: ffffffff ffffffff ffffffff ffffffff ................ +40080080: ffffffff ffffffff ffffffff ffffffff ................ +40080090: ffffffff ffffffff ffffffff ffffffff ................ +400800a0: ffffffff ffffffff ffffffff ffffffff ................ +400800b0: ffffffff ffffffff ffffffff ffffffff ................ +400800c0: ffffffff ffffffff ffffffff ffffffff ................ +400800d0: ffffffff ffffffff ffffffff ffffffff ................ +400800e0: ffffffff ffffffff ffffffff ffffffff ................ +400800f0: ffffffff ffffffff ffffffff ffffffff ................ +=> md 400c0000 +400c0000: ffffffff ffffffff ffffffff ffffffff ................ +400c0010: ffffffff ffffffff ffffffff ffffffff ................ +400c0020: ffffffff ffffffff ffffffff ffffffff ................ +400c0030: ffffffff ffffffff ffffffff ffffffff ................ +400c0040: ffffffff ffffffff ffffffff ffffffff ................ +400c0050: ffffffff ffffffff ffffffff ffffffff ................ +400c0060: ffffffff ffffffff ffffffff ffffffff ................ +400c0070: ffffffff ffffffff ffffffff ffffffff ................ +400c0080: ffffffff ffffffff ffffffff ffffffff ................ +400c0090: ffffffff ffffffff ffffffff ffffffff ................ +400c00a0: ffffffff ffffffff ffffffff ffffffff ................ +400c00b0: ffffffff ffffffff ffffffff ffffffff ................ +400c00c0: ffffffff ffffffff ffffffff ffffffff ................ +400c00d0: ffffffff ffffffff ffffffff ffffffff ................ +400c00e0: ffffffff ffffffff ffffffff ffffffff ................ +400c00f0: ffffffff ffffffff ffffffff ffffffff ................ +=> +------------------------------------------------------------------------------ + + +The following sequence was performed to test the Flash programming commands: + +------------------------------------------------------------------------------ +=> erase 40080000 400bffff +Erase Flash from 0x40080000 to 0x400bffff +.. done +Erased 1 sectors +=> cp 0 40080000 10 +Copy to Flash... done +=> md 0 +00000000: 00000000 00000104 61100200 01000000 ........a....... +00000010: 00000000 00000000 81140000 82000100 ................ +00000020: 01080000 00004000 22800000 00000600 ......@."....... +00000030: 00200800 00000000 10000100 00008000 . .............. +00000040: 00812000 00000200 00020000 80000000 .. ............. +00000050: 00028001 00001000 00040400 00000200 ................ +00000060: 20480000 00000000 20090000 00142000 H...... ..... . +00000070: 00000000 00004000 24210000 10000000 ......@.$!...... +00000080: 02440002 10000000 00200008 00000000 .D....... ...... +00000090: 02440900 00000000 30a40000 00004400 .D......0.....D. +000000a0: 04420800 00000000 00000040 00020000 .B.........@.... +000000b0: 05020000 00100000 00060000 00000000 ................ +000000c0: 00400000 00000000 00080000 00040000 .@.............. +000000d0: 10400000 00800004 00000000 00000200 .@.............. +000000e0: 80890000 00010004 00080000 00000020 ............... +000000f0: 08000000 10000000 00010000 00000000 ................ +=> md 40080000 +40080000: 00000000 00000104 61100200 01000000 ........a....... +40080010: 00000000 00000000 81140000 82000100 ................ +40080020: 01080000 00004000 22800000 00000600 ......@."....... +40080030: 00200800 00000000 10000100 00008000 . .............. +40080040: ffffffff ffffffff ffffffff ffffffff ................ +40080050: ffffffff ffffffff ffffffff ffffffff ................ +40080060: ffffffff ffffffff ffffffff ffffffff ................ +40080070: ffffffff ffffffff ffffffff ffffffff ................ +40080080: ffffffff ffffffff ffffffff ffffffff ................ +40080090: ffffffff ffffffff ffffffff ffffffff ................ +400800a0: ffffffff ffffffff ffffffff ffffffff ................ +400800b0: ffffffff ffffffff ffffffff ffffffff ................ +400800c0: ffffffff ffffffff ffffffff ffffffff ................ +400800d0: ffffffff ffffffff ffffffff ffffffff ................ +400800e0: ffffffff ffffffff ffffffff ffffffff ................ +400800f0: ffffffff ffffffff ffffffff ffffffff ................ +=> +------------------------------------------------------------------------------ + + +The following sequence was performed to test storage of the environment +variables in Flash: + +------------------------------------------------------------------------------ +=> setenv foo bar +=> saveenv +Un-Protected 1 sectors +Erasing Flash... +.. done +Erased 1 sectors +Saving Environment to Flash... +Protected 1 sectors +=> reset +... +=> printenv +bootdelay=CONFIG_BOOTDELAY +baudrate=9600 +ipaddr=192.168.4.7 +serverip=192.168.4.1 +ethaddr=66:55:44:33:22:11 +foo=bar +stdin=serial +stdout=serial +stderr=serial + +Environment size: 170/262140 bytes +=> +------------------------------------------------------------------------------ + + +The following sequence was performed to test image download and run over +Ethernet interface (both interfaces were tested): + +------------------------------------------------------------------------------ +=> tftpboot 40000 hello_world.bin +ARP broadcast 1 +TFTP from server 192.168.2.2; our IP address is 192.168.2.7 +Filename 'hello_world.bin'. +Load address: 0x40000 +Loading: ############# +done +Bytes transferred = 65912 (10178 hex) +=> go 40004 +## Starting application at 0x00040004 ... +Hello World +argc = 1 +argv[0] = "40004" +argv[1] = "" +Hit any key to exit ... + +## Application terminated, rc = 0x0 +=> +------------------------------------------------------------------------------ + + +The following sequence was performed to test eeprom read/write commands: + +------------------------------------------------------------------------------ +=> md 40000 +00040000: 00018148 9421ffe0 7c0802a6 bf61000c ...H.!..|....a.. +00040010: 90010024 48000005 7fc802a6 801effe8 ...$H........... +00040020: 7fc0f214 7c7f1b78 813f004c 7c9c2378 ....|..x.?.L|.#x +00040030: 807e8000 7cbd2b78 80090010 3b600000 .~..|.+x....;`.. +00040040: 7c0803a6 4e800021 813f004c 7f84e378 |...N..!.?.L...x +00040050: 807e8004 80090010 7c0803a6 4e800021 .~......|...N..! +00040060: 7c1be000 4181003c 80bd0000 813f004c |...A..<.....?.L +00040070: 3bbd0004 2c050000 40820008 80be8008 ;...,...@....... +00040080: 80090010 7f64db78 807e800c 3b7b0001 .....d.x.~..;{.. +00040090: 7c0803a6 4e800021 7c1be000 4081ffcc |...N..!|...@... +000400a0: 813f004c 807e8010 80090010 7c0803a6 .?.L.~......|... +000400b0: 4e800021 813f004c 80090004 7c0803a6 N..!.?.L....|... +000400c0: 4e800021 2c030000 4182ffec 813f004c N..!,...A....?.L +000400d0: 80090000 7c0803a6 4e800021 813f004c ....|...N..!.?.L +000400e0: 807e8014 80090010 7c0803a6 4e800021 .~......|...N..! +000400f0: 38600000 80010024 7c0803a6 bb61000c 8`.....$|....a.. +=> eeprom write 40000 0 40 + +EEPROM write: addr 00040000 off 0000 count 64 ... done +=> mw 50000 0 1000 +=> eeprom read 50000 0 40 + +EEPROM read: addr 00050000 off 0000 count 64 ... done +=> md 50000 +00050000: 00018148 9421ffe0 7c0802a6 bf61000c ...H.!..|....a.. +00050010: 90010024 48000005 7fc802a6 801effe8 ...$H........... +00050020: 7fc0f214 7c7f1b78 813f004c 7c9c2378 ....|..x.?.L|.#x +00050030: 807e8000 7cbd2b78 80090010 3b600000 .~..|.+x....;`.. +00050040: 00000000 00000000 00000000 00000000 ................ +00050050: 00000000 00000000 00000000 00000000 ................ +00050060: 00000000 00000000 00000000 00000000 ................ +00050070: 00000000 00000000 00000000 00000000 ................ +00050080: 00000000 00000000 00000000 00000000 ................ +00050090: 00000000 00000000 00000000 00000000 ................ +000500a0: 00000000 00000000 00000000 00000000 ................ +000500b0: 00000000 00000000 00000000 00000000 ................ +000500c0: 00000000 00000000 00000000 00000000 ................ +000500d0: 00000000 00000000 00000000 00000000 ................ +000500e0: 00000000 00000000 00000000 00000000 ................ +000500f0: 00000000 00000000 00000000 00000000 ................ +=> +------------------------------------------------------------------------------ + + +Patch per Mon, 06 Aug 2001 17:57:27: + +- upgraded Flash support (added support for the following chips: + AM29LV800T/B, AM29LV160T/B, AM29DL322T/B, AM29DL323T/B) +- BCR tweakage for the 8260 bus mode +- SIUMCR tweakage enabling the MI interrupt (IRQ7) + +To simplify switching between the bus modes, a new configuration +option (CONFIG_BUSMODE_60x) has been added to the "config_TQM8260.h" +file. If it is defined, BCR will be configured for the 60x mode, +otherwise - for the 8260 mode. + +Concerning the SIUMCR modification: it's hard to predict whether it +will induce any problems on the other (60x mode) board. However, the +problems (if they appear) should be easy to notice - if the board +does not boot, it's most likely caused by the DPPC configuration in +SIUMCR. diff --git a/doc/README.bedbug b/doc/README.bedbug new file mode 100644 index 0000000..ed7bc12 --- /dev/null +++ b/doc/README.bedbug @@ -0,0 +1,89 @@ +BEDBUG Support for U-Boot +-------------------------- + +These changes implement the bedbug (emBEDded deBUGger) debugger in U-Boot. +A specific implementation is made for the IBM405 processor but other flavors +can be easily implemented. + +##################### +### Modifications ### +##################### + +./common/Makefile + Included cmd_bedbug.c and bedbug.c in the Makefile. + +./common/command.c + Added bedbug commands to command table. + +./common/board.c + Added call to initialize debugger on startup. + +./cpu/ppc4xx/Makefile + Added bedbug_405.c to the Makefile. + +./cpu/ppc4xx/start.S + Added code to handle the debug exception (0x2000) on the 405. + Also added code to handle critical exceptions since the debug + is treated as critical on the 405. + +./cpu/ppc4xx/traps.c + Added more detailed output for the program exception to tell + if it is an illegal instruction, privileged instruction or + a trap. Also added debug trap handler. + +./include/cmd_confdefs.h + Added definition of CFG_CMD_BEDBUG. + +./include/config_WALNUT405.h + Added CFG_CMD_BEDBUG to the CONFIG_COMMANDS for the WALNUT. + +./include/ppc_asm.tmpl + Added code to handle critical exceptions + +################# +### New Stuff ### +################# + +./include/bedbug/ppc.h +./include/bedbug/regs.h +./include/bedbug/bedbug.h +./include/bedbug/elf.h [obsoleted by new include/elf.h] +./include/bedbug/tables.h +./include/cmd_bedbug.h +./common/cmd_bedbug.c +./common/bedbug.c + Bedbug library includes code for assembling and disassembling + PowerPC instructions to/from memory as well as handling + hardware breakpoints and stepping through code. These + routines are common to all PowerPC processors. + +./cpu/ppc4xx/bedbug_405.c + IBM PPC405 specific debugger routines. + + + +Bedbug support for the MPC860 +----------------------------- + +Changes: + + common/cmd_bedbug.c + Added call to initialize 860 debugger. + + cpu/mpc8xx/Makefile + Added new file "bedbug_860.c" to the makefile + + cpu/mpc8xx/start.S + Added handler for InstructionBreakpoint (0xfd00) + + cpu/mpc8xx/traps.c + Added new routine DebugException() + + include/config_MBX.h + Added CFG_CMD_BEDBUG to CONFIG_COMMANDS define + + +New Files: + + cpu/mpc8xx/bedbug_860.c + CPU-specific routines for 860 debug registers. diff --git a/doc/README.evb64260 b/doc/README.evb64260 new file mode 100644 index 0000000..74211de --- /dev/null +++ b/doc/README.evb64260 @@ -0,0 +1,54 @@ +This file contains status information for the port of U-Boot to the +Galileo Evaluation Board. + +Author: Josh Huber + Mission Critical Linux, Inc. + +The support for the Galileo Evaluation board is fairly minimal now. +It's sufficient to boot Linux, but doesn't provide too much more than +what's required to do this. + +Both DUART channels are supported (to use the second one, you have to +modify the board -- see the schematics for where to solder on the +devices module). The ethernet ports are supported, and the MPSC is +supported as a console driver. (keep in mind that the kernel has no +support for this yet) + +There are still occaisonal lockups with the MPSC console driver due to +(we think!) overrun problems. If you're looking for something stable +to use for Linux development, consider sticking with the DUART console +for now. + +Automatic memory sizing mostly works. We've had problems with some +combinations of memory. Please send us email if you're having trouble +with respect to the memory detection. + +Right now, only the 512k boot flash is supported. Support for the +16MB flash on the devices module is forthcoming. Right now the flash +is stored at the 256k boundry in flash, wasting a whole sector (64k!) +for environment data. This isn't really a big deal since we're not +using the 512k for anything else. (Just U-Boot and the environment) + +Finally, here is a sample output session: + +U-Boot 1.0.0-pre1 (Jun 6 2001 - 12:45:11) + +Initializing... + CPU: MPC7400 (altivec enabled) v2.9 + Board: EVB64260 + DRAM: 256 MB + FLASH: 512 kB + In: serial + Out: serial + Err: serial + +=> + +The default configuration should be correct for the evaluation board, +as it's shipped from Galileo. Keep in mind that the default baudrate +is set to 38400, 8N1. + +Good luck, and make sure to send any bugreports to us (or the +u-boot-users list). + +Josh diff --git a/doc/README.mpc74xx b/doc/README.mpc74xx new file mode 100644 index 0000000..f81f1c2 --- /dev/null +++ b/doc/README.mpc74xx @@ -0,0 +1,22 @@ +This file contains status information for the port of U-Boot to the +Motorola mpc74xx series of CPUs. + +Author: Josh Huber + Mission Critical Linux, Inc. + +Currently the support for these CPUs is pretty minimal, but enough to +get things going. (much like the support for the Galileo Eval Board) + +There is a framework in place to enable the L2 cache, and to program +the BATs. Currently, there are still problems with the code which +sets up the L2 cache, so it's not enabled. (IMHO, it shouldn't be +anyway). Additionally, there is support for enabling the MMU, which +we also don't do. The BATs are programmed just for the benefit of +jumping into Linux in a sane configuration. + +Most of the code was based on other cpus supported by U-Boot. + +If you find any errors in the CPU setup code, please send us a note. + +Thanks, +Josh diff --git a/doc/README.usb b/doc/README.usb new file mode 100644 index 0000000..41f76f4 --- /dev/null +++ b/doc/README.usb @@ -0,0 +1,80 @@ +/* + * (C) Copyright 2001 + * Denis Peter, MPL AG Switzerland + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +USB Support for PIP405 and MIP405 (UHCI) +======================================== + +The USB support is implemented on the base of the UHCI Host +controller. + +Currently supported are USB Hubs, USB Keyboards and USB Floppys. +Tested with a TEAC Floppy TEAC FD-05PUB and Chicony KU-8933 Keyboard. + +How it works: +------------- + +The USB (at least the USB UHCI) needs a frame list (4k), transfer +descripor and queue headers which are all located in the main memory. +The UHCI allocates every milisecond the PCI bus and reads the current +frame pointer. This may cause to crash the OS during boot. So the USB +_MUST_ be stopped during OS boot. This is the reason, why the USB is +NOT automatically started during start-up. If someone needs the USB +he has to start it and should therefore be aware that he had to stop +it before booting the OS. + +For USB keyboards this can be done by a script which is automatically +started after the U-Boot is up and running. To boot an OS with a an +USB keyboard another script is necessary, which first disables the +USB and then executes the boot command. If the boot command fails, +the script can reenable the USB kbd. + +Common USB Commands: +- usb start: +- usb reset: (re)starts the USB. All USB devices will be + initialized and a device tree is build for them. +- usb tree: shows all USB devices in a tree like display +- usb info [dev]: shows all USB infos of the device dev, or of all + the devices +- usb stop [f]: stops the USB. If f==1 the USB will also stop if + an USB keyboard is assigned as stdin. The stdin + is then switched to serial input. +Storage USB Commands: +- usb scan: scans the USB for storage devices.The USB must be + running for this command (usb start) +- usb device [dev]: show or set current USB staorage device +- usb part [dev]: print partition table of one or all USB storage + devices +- usb read addr blk# cnt: + read `cnt' blocks starting at block `blk#'to + memory address `addr' +- usbboot addr dev:part: + boot from USB device + +Config Switches: +---------------- +CFG_CMD_USB enables basic USB support and the usb command +CONFIG_USB_UHCI defines the lowlevel part.A lowlevel part must be defined if + using CFG_CMD_USB +CONFIG_USB_KEYBOARD enables the USB Keyboard +CONFIG_USB_STORAGE enables the USB storage devices diff --git a/include/asm-ppc/hymod.h b/include/asm-ppc/hymod.h new file mode 100644 index 0000000..b4179bf --- /dev/null +++ b/include/asm-ppc/hymod.h @@ -0,0 +1,289 @@ +#ifndef _ASM_HYMOD_H_ +#define _ASM_HYMOD_H_ + +#include +#ifdef CONFIG_8260 +#include +#endif + +/* + * hymod configuration data - passed by boot code via the board information + * structure (only U-Boot has support for this at the moment) + * + * there are three types of data passed up from the boot monitor. the first + * (type hymod_eeprom_t) is the eeprom data that was read off both the main + * (or mother) board and the mezzanine board (if any). this data defines how + * many Xilinx fpgas are on each board, and their types (among other things). + * the second type of data (type xlx_mmap_t, one per Xilinx fpga) defines where + * in the physical address space the various Xilinx fpga access regions have + * been mapped by the boot rom. the third type of data (type xlx_iopins_t, + * one per Xilinx fpga) defines which io port pins are connected to the various + * signals required to program a Xilinx fpga. + * + * A ram/flash "bank" refers to memory controlled by the same chip select. + * + * the eeprom contents are defined as in technical note #2 - basically, + * a header, zero or more records in no particular order, and a 32 bit crc + * a record is 1 or more type bytes, a length byte and "length" bytes. + */ + +#define HYMOD_EEPROM_ID 0xAA /* eeprom id byte */ +#define HYMOD_EEPROM_VER 1 /* eeprom contents version */ +#define HYMOD_EEPROM_SIZE 256 /* number of bytes in the eeprom */ + +/* eeprom header */ +typedef + struct { + unsigned char id; /* eeprom id byte */ + unsigned char ver; /* eeprom contents version number */ + unsigned long len; /* total # of bytes btw hdr and crc */ + } +hymod_eehdr_t; + +/* maximum number of bytes available for eeprom data records */ +#define HYMOD_EEPROM_MAXLEN (HYMOD_EEPROM_SIZE \ + - sizeof (hymod_eehdr_t) \ + - sizeof (unsigned long)) + +/* eeprom data record */ +typedef + union { + struct { + unsigned char topbit:1; + unsigned char type:7; + unsigned char len; + unsigned char data[1]; /* variable length */ + } small; + struct { + unsigned short topbit:1; + unsigned short nxtbit:1; + unsigned short type:14; + unsigned short len; + unsigned char data[1]; /* variable length */ + } medium; + struct { + unsigned long topbit:1; + unsigned long nxtbit:1; + unsigned long type:30; + unsigned long len; + unsigned char data[1]; /* variable length */ + } large; + } +hymod_eerec_t; + +#define HYMOD_EEOFF_MAIN 0x00 /* i2c addr offset for main eeprom */ +#define HYMOD_EEOFF_MEZZ 0x04 /* i2c addr offset for mezz eepomr */ + +/* eeprom record types */ +#define HYMOD_EEREC_SERNO 1 /* serial number */ +#define HYMOD_EEREC_DATE 2 /* date */ +#define HYMOD_EEREC_BATCH 3 /* batch id */ +#define HYMOD_EEREC_TYPE 4 /* board type */ +#define HYMOD_EEREC_REV 5 /* revision number */ +#define HYMOD_EEREC_SDRAM 6 /* sdram sizes */ +#define HYMOD_EEREC_FLASH 7 /* flash sizes */ +#define HYMOD_EEREC_ZBT 8 /* zbt ram sizes */ +#define HYMOD_EEREC_XLXTYP 9 /* Xilinx fpga types */ +#define HYMOD_EEREC_XLXSPD 10 /* Xilinx fpga speeds */ +#define HYMOD_EEREC_XLXTMP 11 /* Xilinx fpga temperatures */ +#define HYMOD_EEREC_XLXGRD 12 /* Xilinx fpga grades */ +#define HYMOD_EEREC_CPUTYP 13 /* Motorola CPU type */ +#define HYMOD_EEREC_CPUSPD 14 /* CPU speed */ +#define HYMOD_EEREC_BUSSPD 15 /* bus speed */ +#define HYMOD_EEREC_CPMSPD 16 /* CPM speed */ +#define HYMOD_EEREC_HSTYPE 17 /* high-speed serial chip type */ +#define HYMOD_EEREC_HSCHIN 18 /* high-speed serial input channels */ +#define HYMOD_EEREC_HSCHOUT 19 /* high-speed serial output channels */ + +/* some dimensions */ +#define HYMOD_MAX_BATCH 32 /* max no. of bytes in batch id */ +#define HYMOD_MAX_SDRAM 4 /* max sdram "banks" on any board */ +#define HYMOD_MAX_FLASH 4 /* max flash "banks" on any board */ +#define HYMOD_MAX_ZBT 16 /* max ZBT rams on any board */ +#define HYMOD_MAX_XLX 4 /* max Xilinx fpgas on any board */ + +#define HYMOD_MAX_BYTES 16 /* enough to store any bytes array */ + +/* board types */ +#define HYMOD_BDTYPE_NONE 0 /* information not present */ +#define HYMOD_BDTYPE_IO 1 /* I/O main board */ +#define HYMOD_BDTYPE_CLP 2 /* CLP main board */ +#define HYMOD_BDTYPE_DSP 3 /* DSP main board */ +#define HYMOD_BDTYPE_INPUT 4 /* video input mezzanine board */ +#define HYMOD_BDTYPE_ALTINPUT 5 /* video input mezzanine board */ +#define HYMOD_BDTYPE_DISPLAY 6 /* video display mezzanine board */ +#define HYMOD_BDTYPE_MAX 7 /* first invalid value */ + +/* Xilinx fpga types */ +#define HYMOD_XTYP_NONE 0 /* information not present */ +#define HYMOD_XTYP_XCV300E 1 /* Xilinx Virtex 300 */ +#define HYMOD_XTYP_XCV400E 2 /* Xilinx Virtex 400 */ +#define HYMOD_XTYP_XCV600E 3 /* Xilinx Virtex 600 */ +#define HYMOD_XTYP_MAX 4 /* first invalid value */ + +/* Xilinx fpga speeds */ +#define HYMOD_XSPD_NONE 0 /* information not present */ +#define HYMOD_XSPD_SIX 1 +#define HYMOD_XSPD_SEVEN 2 +#define HYMOD_XSPD_EIGHT 3 +#define HYMOD_XSPD_MAX 4 /* first invalid value */ + +/* Xilinx fpga temperatures */ +#define HYMOD_XTMP_NONE 0 /* information not present */ +#define HYMOD_XTMP_COM 1 +#define HYMOD_XTMP_IND 2 +#define HYMOD_XTMP_MAX 3 /* first invalid value */ + +/* Xilinx fpga grades */ +#define HYMOD_XTMP_NONE 0 /* information not present */ +#define HYMOD_XTMP_NORMAL 1 +#define HYMOD_XTMP_ENGSAMP 2 +#define HYMOD_XTMP_MAX 3 /* first invalid value */ + +/* CPU types */ +#define HYMOD_CPUTYPE_NONE 0 /* information not present */ +#define HYMOD_CPUTYPE_MPC8260 1 /* Motorola MPC8260 embedded powerpc */ +#define HYMOD_CPUTYPE_MAX 2 /* first invalid value */ + +/* CPU/BUS/CPM clock speeds */ +#define HYMOD_CLKSPD_NONE 0 /* information not present */ +#define HYMOD_CLKSPD_33MHZ 1 +#define HYMOD_CLKSPD_66MHZ 2 +#define HYMOD_CLKSPD_100MHZ 3 +#define HYMOD_CLKSPD_133MHZ 4 +#define HYMOD_CLKSPD_166MHZ 5 +#define HYMOD_CLKSPD_200MHZ 6 +#define HYMOD_CLKSPD_MAX 7 /* first invalid value */ + +/* high speed serial chip types */ +#define HYMOD_HSSTYPE_NONE 0 /* information not present */ +#define HYMOD_HSSTYPE_AMCC52064 1 +#define HYMOD_HSSTYPE_MAX 2 /* first invalid value */ + +/* a date (yyyy-mm-dd) */ +typedef + struct { + unsigned short year; + unsigned char month; + unsigned char day; + } +hymod_date_t; + +/* describes a Xilinx fpga */ +typedef + struct { + unsigned char type; /* chip type */ + unsigned char speed; /* chip speed rating */ + unsigned char temp; /* chip temperature rating */ + unsigned char grade; /* chip grade */ + } +hymod_xlx_t; + +/* describes a Motorola embedded processor */ +typedef + struct { + unsigned char type; /* CPU type */ + unsigned char cpuspd; /* speed of the PowerPC core */ + unsigned char busspd; /* speed of the system and 60x bus */ + unsigned char cpmspd; /* speed of the CPM co-processor */ + } +hymod_mpc_t; + +/* info about high-speed (1Gbit) serial interface */ +typedef + struct { + unsigned char type; /* high-speed serial chip type */ + unsigned char nchin; /* number of input channels mounted */ + unsigned char nchout; /* number of output channels mounted */ + } +hymod_hss_t; + +/* + * this defines the contents of the serial eeprom that exists on every + * hymod board, including mezzanine boards (the serial eeprom will be + * faked for early development boards that don't have one) + */ + +typedef + struct { + unsigned char ver; /* eeprom contents version */ + unsigned char bdtype; /* board type */ + unsigned char bdrev; /* board revision */ + unsigned char batchlen; /* length of batch string below */ + unsigned long serno; /* serial number */ + hymod_date_t date; /* manufacture date */ + unsigned char batch[32]; /* manufacturer specific batch id */ + unsigned char nsdram; /* # of ram "banks" */ + unsigned char nflash; /* # of flash "banks" */ + unsigned char nzbt; /* # of ZBT rams */ + unsigned char nxlx; /* # of Xilinx fpgas */ + unsigned char sdramsz[HYMOD_MAX_SDRAM]; /* log2 of sdram size */ + unsigned char flashsz[HYMOD_MAX_FLASH]; /* log2 of flash size */ + unsigned char zbtsz[HYMOD_MAX_ZBT]; /* log2 of ZBT ram size */ + hymod_xlx_t xlx[HYMOD_MAX_XLX]; /* Xilinx fpga info */ + hymod_mpc_t mpc; /* Motorola MPC CPU info */ + hymod_hss_t hss; /* high-speed serial info */ + } +hymod_eeprom_t; + +/* + * this defines a region in the processor's physical address space + */ +typedef + struct { + unsigned long exists:1; /* 1 if the region exists, 0 if not */ + unsigned long size:31; /* size in bytes */ + unsigned long base; /* base address */ + } +xlx_prgn_t; + +/* + * this defines where the various Xilinx fpga access regions are mapped + * into the physical address space of the processor + */ +typedef + struct { + xlx_prgn_t prog; /* program access region */ + xlx_prgn_t reg; /* register access region */ + xlx_prgn_t port; /* port access region */ + } +xlx_mmap_t; + +/* + * this defines which 8260 i/o port pins are connected to the various + * signals required for programming a Xilinx fpga + */ +typedef + struct { + iopin_t prog_pin; /* assert for >= 300ns to program */ + iopin_t init_pin; /* goes high when fpga is cleared */ + iopin_t done_pin; /* goes high when program is done */ + iopin_t enable_pin; /* some fpgas need enabling */ + } +xlx_iopins_t; + +/* all info about one hymod board */ +typedef + struct { + unsigned char eeprom_valid:1; + hymod_eeprom_t eeprom; + xlx_mmap_t mmap[HYMOD_MAX_XLX]; + xlx_iopins_t iopins[HYMOD_MAX_XLX]; + } +hymod_board_t; + +/* + * this defines the configuration information of a hymod board-set + * (main board + possible mezzanine board). In future, there may be + * more than one mezzanine board (stackable?) - if so, add a "mezz2" + * field, and so on... or make mezz an array? + */ +typedef + struct { + hymod_board_t main; /* main board info */ + hymod_board_t mezz; /* mezzanine board info */ + unsigned long crc; /* ensures kernel and boot prom agree */ + } +hymod_conf_t; + +#endif /* _ASM_HYMOD_H_ */ diff --git a/include/cmd_kgdb.h b/include/cmd_kgdb.h new file mode 100644 index 0000000..945c54e --- /dev/null +++ b/include/cmd_kgdb.h @@ -0,0 +1,52 @@ +/* + * (C) Copyright 2000 + * Murray Jensen and + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * KGDB support + */ +#ifndef _CMD_KGDB_H +#define _CMD_KGDB_H + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CMD_TBL_KGDB MK_CMD_TBL_ENTRY( \ + "kgdb", 4, CFG_MAXARGS, 1, do_kgdb, \ + "kgdb - enter gdb remote debug mode\n", \ + "[arg0 arg1 .. argN]\n" \ + " - executes a breakpoint so that kgdb mode is\n" \ + " entered via the exception handler. To return\n" \ + " to the monitor, the remote gdb debugger must\n" \ + " execute a \"continue\" or \"quit\" command.\n" \ + "\n" \ + " if a program is loaded by the remote gdb, any args\n" \ + " passed to the kgdb command are given to the loaded\n" \ + " program if it is executed (see the \"hello_world\"\n" \ + " example program in the U-Boot examples directory)." \ +), + +int do_kgdb (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); +#else +#define CMD_TBL_KGDB +#endif + +#endif /* _CMD_KGDB_H */ diff --git a/include/common.h b/include/common.h new file mode 100644 index 0000000..49ab97c --- /dev/null +++ b/include/common.h @@ -0,0 +1,428 @@ +/* + * (C) Copyright 2000-2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __COMMON_H_ +#define __COMMON_H_ 1 + +#undef _LINUX_CONFIG_H +#define _LINUX_CONFIG_H 1 /* avoid reading Linux autoconf.h file */ + +typedef unsigned char uchar; +typedef volatile unsigned long vu_long; +typedef volatile unsigned short vu_short; +typedef volatile unsigned char vu_char; + +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_PCI) && defined(CONFIG_440) +#include +#endif +#ifdef CONFIG_8xx +#include +#elif defined(CONFIG_8260) +#include +#endif +#ifdef CONFIG_4xx +#include +#endif +#ifdef CONFIG_HYMOD +#include +#endif +#ifdef CONFIG_ARM +#define asmlinkage /* nothing */ +#endif + +#include +#include +#include + +#ifdef DEBUG +#define debug(fmt,args...) printf (fmt ,##args) +#else +#define debug(fmt,args...) +#endif /* DEBUG */ + +typedef void (interrupt_handler_t)(void *); + +#include /* boot information for Linux kernel */ +#include /* global data used for startup functions */ + +/* enable common handling for all TQM8xxL boards */ +#if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L) || \ + defined(CONFIG_TQM855L) || defined(CONFIG_TQM860L) +# ifndef CONFIG_TQM8xxL +# define CONFIG_TQM8xxL +# endif +#endif + + +/* + * Function Prototypes + */ + +#if CONFIG_SERIAL_SOFTWARE_FIFO +void serial_buffered_init (void); +void serial_buffered_putc (const char); +void serial_buffered_puts (const char *); +int serial_buffered_getc (void); +int serial_buffered_tstc (void); +#endif /* CONFIG_SERIAL_SOFTWARE_FIFO */ + +void hang (void) __attribute__ ((noreturn)); + +/* */ +long int initdram (int); +int display_options (void); +void print_size (ulong, const char *); + +/* common/main.c */ +void main_loop (void); +int run_command (const char *cmd, int flag); +int readline (const char *const prompt); +void reset_cmd_timeout(void); + +/* common/board.c */ +void board_init_f (ulong); +void board_init_r (gd_t *, ulong); +int checkboard (void); +int checkflash (void); +int checkdram (void); +char * strmhz(char *buf, long hz); +int last_stage_init(void); + +/* common/flash.c */ +void flash_perror (int); + +/* common/cmd_bootm.c */ +void print_image_hdr (image_header_t *hdr); + +extern ulong load_addr; /* Default Load Address */ + +/* common/cmd_nvedit.c */ +int env_init (void); +void env_relocate (void); +char *getenv (uchar *); +int getenv_r (uchar *name, uchar *buf, unsigned len); +int saveenv (void); +#ifdef CONFIG_PPC /* ARM version to be fixed! */ +void inline setenv (char *, char *); +#endif /* CONFIG_PPC */ +#ifdef CONFIG_ARM +# include /* ARM version to be fixed! */ +#endif /* CONFIG_ARM */ + +void pci_init (void); +void pciinfo (int, int); + +#if defined(CONFIG_PCI) && defined(CONFIG_440) +# if defined(CFG_PCI_PRE_INIT) + int pci_pre_init (struct pci_controller * ); +# endif +# if defined(CFG_PCI_TARGET_INIT) + void pci_target_init (struct pci_controller *); +# endif +# if defined(CFG_PCI_MASTER_INIT) + void pci_master_init (struct pci_controller *); +# endif + int is_pci_host (struct pci_controller *); +#endif + +int misc_init_f (void); +int misc_init_r (void); + +/* $(BOARD)/$(BOARD).c */ +void reset_phy (void); + +/* $(BOARD)/eeprom.c */ +void eeprom_init (void); +int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); +int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); +#ifdef CONFIG_LWMON +extern uchar pic_read (uchar reg); +extern void pic_write (uchar reg, uchar val); +#endif + +/* + * Set this up regardless of board + * type, to prevent errors. + */ +#if defined(CONFIG_SPI) || !defined(CFG_I2C_EEPROM_ADDR) +# define CFG_DEF_EEPROM_ADDR 0 +#else +# define CFG_DEF_EEPROM_ADDR CFG_I2C_EEPROM_ADDR +#endif /* CONFIG_SPI || !defined(CFG_I2C_EEPROM_ADDR) */ + +#if defined(CONFIG_PCU_E) || defined(CONFIG_CCM) +extern void spi_init_f (void); +extern void spi_init_r (void); +extern ssize_t spi_read (uchar *, int, uchar *, int); +extern ssize_t spi_write (uchar *, int, uchar *, int); +#endif + +#ifdef CONFIG_RPXCLASSIC +void rpxclassic_init (void); +#endif + +#ifdef CONFIG_MBX +/* $(BOARD)/mbx8xx.c */ +void mbx_init (void); +void board_serial_init (void); +void board_ether_init (void); +#endif + +#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_MBX) || defined(CONFIG_IAD210) +void board_get_enetaddr (uchar *addr); +#endif + +#ifdef CONFIG_HERMES +/* $(BOARD)/hermes.c */ +void hermes_start_lxt980 (int speed); +#endif + +#ifdef CONFIG_EVB64260 +void evb64260_init(void); +void debug_led(int, int); +void display_mem_map(void); +void perform_soft_reset(void); +#endif + +void load_sernum_ethaddr (void); + +/* $(BOARD)/$(BOARD).c */ +int board_pre_init (void); +int board_postclk_init (void); /* after clocks/timebase, before env/serial */ +void board_poweroff (void); + +#if defined(CFG_DRAM_TEST) +int testdram(void); +#endif /* CFG_DRAM_TEST */ + +/* $(CPU)/start.S */ +#ifdef CONFIG_8xx +uint get_immr (uint); +#endif +uint get_pvr (void); +uint rd_ic_cst (void); +void wr_ic_cst (uint); +void wr_ic_adr (uint); +uint rd_dc_cst (void); +void wr_dc_cst (uint); +void wr_dc_adr (uint); +int icache_status (void); +void icache_enable (void); +void icache_disable(void); +int dcache_status (void); +void dcache_enable (void); +void dcache_disable(void); +void relocate_code (ulong, gd_t *, ulong); +ulong get_endaddr (void); +void trap_init (ulong); +#if defined (CONFIG_4xx) || \ + defined (CONFIG_74xx_7xx) || \ + defined (CONFIG_74x) || \ + defined (CONFIG_75x) || \ + defined (CONFIG_74xx) +unsigned char in8(unsigned int); +void out8(unsigned int, unsigned char); +unsigned short in16(unsigned int); +unsigned short in16r(unsigned int); +void out16(unsigned int, unsigned short value); +void out16r(unsigned int, unsigned short value); +unsigned long in32(unsigned int); +unsigned long in32r(unsigned int); +void out32(unsigned int, unsigned long value); +void out32r(unsigned int, unsigned long value); +void ppcDcbf(unsigned long value); +void ppcDcbi(unsigned long value); +void ppcSync(void); +#endif + +/* $(CPU)/cpu.c */ +int checkcpu (void); +int checkicache (void); +int checkdcache (void); +void upmconfig (unsigned int, unsigned int *, unsigned int); +ulong get_tbclk (void); + +/* $(CPU)/serial.c */ +int serial_init (void); +void serial_setbrg (void); +void serial_putc (const char); +void serial_puts (const char *); +void serial_addr (unsigned int); +int serial_getc (void); +int serial_tstc (void); + +/* $(CPU)/speed.c */ +int get_clocks (void); +#if defined(CONFIG_8260) +int prt_8260_clks (void); +#endif +#ifdef CONFIG_4xx +ulong get_OPB_freq (void); +ulong get_PCI_freq (void); +#endif +#if defined(CONFIG_S3C2400) || defined(CONFIG_S3C2410) +ulong get_FCLK (void); +ulong get_HCLK (void); +ulong get_PCLK (void); +ulong get_UCLK (void); +#endif +ulong get_bus_freq (ulong); + +#if defined(CONFIG_4xx) || defined(CONFIG_IOP480) +# if defined(CONFIG_440) + typedef PPC440_SYS_INFO sys_info_t; +# else + typedef PPC405_SYS_INFO sys_info_t; +# endif +void get_sys_info ( sys_info_t * ); +#endif + +/* $(CPU)/cpu_init.c */ +#if defined(CONFIG_8xx) || defined(CONFIG_8260) +void cpu_init_f (volatile immap_t *immr); +#endif +#ifdef CONFIG_4xx +void cpu_init_f (void); +#endif +int cpu_init_r (void); +#if defined(CONFIG_8260) +int prt_8260_rsr (void); +#endif + +/* $(CPU)/interrupts.c */ +int interrupt_init (void); +void timer_interrupt (struct pt_regs *); +void external_interrupt (struct pt_regs *); +void irq_install_handler(int, interrupt_handler_t *, void *); +void irq_free_handler (int); +void reset_timer (void); +ulong get_timer (ulong base); +void set_timer (ulong t); +void enable_interrupts (void); +int disable_interrupts (void); + +/* $(CPU)/.../commproc.c */ +int dpram_init (void); +uint dpram_base(void); +uint dpram_base_align(uint align); +uint dpram_alloc(uint size); +uint dpram_alloc_align(uint size,uint align); +void post_word_store (ulong); +ulong post_word_load (void); + +/* $(CPU)/.../ */ +void mii_init (void); + +/* $(CPU)/.../lcd.c */ +ulong lcd_setmem (ulong); + +/* $(CPU)/.../vfd.c */ +ulong vfd_setmem (ulong); + +/* $(CPU)/.../video.c */ +ulong video_setmem (ulong); + +/* ppc/cache.c */ +void flush_cache (unsigned long, unsigned long); + +/* ppc/ticks.S */ +unsigned long long get_ticks(void); +void wait_ticks (unsigned long); + +/* ppc/time.c */ +void udelay (unsigned long); +ulong usec2ticks (unsigned long usec); +ulong ticks2usec (unsigned long ticks); +int init_timebase (void); + +/* ppc/vsprintf.c */ +ulong simple_strtoul(const char *cp,char **endp,unsigned int base); +long simple_strtol(const char *cp,char **endp,unsigned int base); +void panic(const char *fmt, ...); +int sprintf(char * buf, const char *fmt, ...); +int vsprintf(char *buf, const char *fmt, va_list args); + +/* ppc/crc32.c */ +ulong crc32 (ulong, const unsigned char *, uint); +ulong crc32_no_comp (ulong, const unsigned char *, uint); + +/* common/console.c */ +extern void **syscall_tbl; + +int console_init_f(void); /* Before relocation; uses the serial stuff */ +int console_init_r(void); /* After relocation; uses the console stuff */ +int console_assign (int file, char *devname); /* Assign the console */ +int ctrlc (void); +int had_ctrlc (void); /* have we had a Control-C since last clear? */ +void clear_ctrlc (void); /* clear the Control-C condition */ +int disable_ctrlc (int); /* 1 to disable, 0 to enable Control-C detect */ + +/* + * STDIO based functions (can always be used) + */ + +/* serial stuff */ +void serial_printf (const char *fmt, ...); + +/* stdin */ +int getc(void); +int tstc(void); + +/* stdout */ +void putc(const char c); +void puts(const char *s); +void printf(const char *fmt, ...); + +/* stderr */ +#define eputc(c) fputc(stderr, c) +#define eputs(s) fputs(stderr, s) +#define eprintf(fmt,args...) fprintf(stderr,fmt ,##args) + +/* + * FILE based functions (can only be used AFTER relocation!) + */ + +#define stdin 0 +#define stdout 1 +#define stderr 2 +#define MAX_FILES 3 + +void fprintf(int file, const char *fmt, ...); +void fputs(int file, const char *s); +void fputc(int file, const char c); +int ftstc(int file); +int fgetc(int file); + +int pcmcia_init (void); + +#ifdef CONFIG_SHOW_BOOT_PROGRESS +void show_boot_progress (int status); +#endif + +#endif /* __COMMON_H_ */ diff --git a/include/configs/BAB7xx.h b/include/configs/BAB7xx.h new file mode 100644 index 0000000..d312e6b --- /dev/null +++ b/include/configs/BAB7xx.h @@ -0,0 +1,452 @@ +/* + * (C) Copyright 2002 ELTEC Elektronik AG + * Frank Gottschling + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include + +#undef DEBUG +#define GTREGREAD(x) 0xffffffff /* needed for debug */ + +/* + * High Level Configuration Options + * (easy to change) + */ + +/* these hardware addresses are pretty bogus, please change them to + suit your needs */ + +/* first ethernet */ +#define CONFIG_ETHADDR 00:00:5b:ee:de:ad + +#define CONFIG_IPADDR 192.168.0.105 +#define CONFIG_SERVERIP 192.168.0.100 + +#define CONFIG_BAB7xx 1 /* this is an BAB740/BAB750 board */ + +#define CONFIG_BAUDRATE 9600 /* console baudrate */ + +#undef CONFIG_WATCHDOG + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp 1000000; " \ + "setenv bootargs root=ramfs console=ttyS00,9600 " \ + "ip=$(ipaddr):$(serverip):$(rootpath):$(gatewayip):" \ + "$(netmask):$(hostname):eth0:none; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2 |\ + CFG_CMD_SCSI | CFG_CMD_IDE | CFG_CMD_DATE |\ + CFG_CMD_FDC | CFG_CMD_ELF) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +/* + * choose between COM1 and COM2 as serial console + */ +#define CONFIG_CONS_INDEX 1 + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x04000000 /* 0 ... 64 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x1000000 /* default load address */ + +#define CFG_HZ 1000 /* dec. freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +#define CFG_BOARD_ASM_INIT +#define CONFIG_MISC_INIT_R + +/* + * Choose the address mapping scheme for the MPC106 mem controller. + * Default is mapping B (CHRP), set this define to choose mapping A (PReP). + */ +#define CFG_ADDRESS_MAP_A +#ifdef CFG_ADDRESS_MAP_A + +#define CFG_PCI_MEMORY_BUS 0x80000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +#define CFG_PCI_MEM_BUS 0x00000000 +#define CFG_PCI_MEM_PHYS 0xc0000000 +#define CFG_PCI_MEM_SIZE 0x3f000000 + +#define CFG_ISA_MEM_BUS 0 +#define CFG_ISA_MEM_PHYS 0 +#define CFG_ISA_MEM_SIZE 0 + +#define CFG_PCI_IO_BUS 0x1000 +#define CFG_PCI_IO_PHYS 0x81000000 +#define CFG_PCI_IO_SIZE 0x01000000-CFG_PCI_IO_BUS + +#define CFG_ISA_IO_BUS 0x00000000 +#define CFG_ISA_IO_PHYS 0x80000000 +#define CFG_ISA_IO_SIZE 0x00800000 + +#else + +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x40000000 + +#define CFG_PCI_MEM_BUS 0x80000000 +#define CFG_PCI_MEM_PHYS 0x80000000 +#define CFG_PCI_MEM_SIZE 0x7d000000 + +#define CFG_ISA_MEM_BUS 0x00000000 +#define CFG_ISA_MEM_PHYS 0xfd000000 +#define CFG_ISA_MEM_SIZE 0x01000000 + +#define CFG_PCI_IO_BUS 0x00800000 +#define CFG_PCI_IO_PHYS 0xfe800000 +#define CFG_PCI_IO_SIZE 0x00400000 + +#define CFG_ISA_IO_BUS 0x00000000 +#define CFG_ISA_IO_PHYS 0xfe000000 +#define CFG_ISA_IO_SIZE 0x00800000 + +#endif /*CFG_ADDRESS_MAP_A */ + +#define CFG_60X_PCI_MEM_OFFSET 0x00000000 + +/* driver defines FDC,IDE,... */ +#define CFG_ISA_IO_BASE_ADDRESS CFG_ISA_IO_PHYS +#define CFG_ISA_IO CFG_ISA_IO_PHYS +#define CFG_60X_PCI_IO_OFFSET CFG_ISA_IO_PHYS + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xfff00000 + +/* + * Definitions for initial stack pointer and data area + */ +#define CFG_INIT_RAM_ADDR 0x00fd0000 /* above the memtest region */ +#define CFG_INIT_RAM_END 0x4000 +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for init data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* + * Flash mapping/organization on the MPC10x. + */ +#define FLASH_BASE0_PRELIM 0xff800000 +#define FLASH_BASE1_PRELIM 0xffc00000 + +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ +#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ + +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN 0x20000 /* Reserve 128 kB for malloc() */ +#undef CFG_MEMTEST + +/* + * Environment settings + */ +#define CONFIG_ENV_OVERWRITE +#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ +#define CFG_NVRAM_SIZE 0x1ff0 /* NVRAM size (8kB), we must protect the clock data (16 bytes) */ +#define CFG_ENV_SIZE 0x400 /* Size of Environment vars (1kB) */ +/* + * We store the environment and an image of revision eeprom in the upper part of the NVRAM. Thus, + * user applications can use the remaining space for other purposes. + */ +#define CFG_ENV_ADDR (CFG_NVRAM_SIZE +0x10 -0x800) +#define CFG_NV_SROM_COPY_ADDR (CFG_NVRAM_SIZE +0x10 -0x400) +#define CFG_NVRAM_ACCESS_ROUTINE /* This board needs a special routine to access the NVRAM */ +#define CFG_SROM_SIZE 0x100 /* shadow of revision info is in nvram */ + +/* + * Serial devices + */ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK 1843200 +#define CFG_NS16550_COM1 (CFG_ISA_IO + CFG_NS87308_UART1_BASE) +#define CFG_NS16550_COM2 (CFG_ISA_IO + CFG_NS87308_UART2_BASE) + +/* + * PCI stuff + */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* pci plug-and-play */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO +#undef CONFIG_PCI_SCAN_SHOW + +/* + * Video console (graphic: SMI LynxEM, keyboard: i8042) + */ +#define CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_SMI_LYNXEM +#define CONFIG_I8042_KBD +#define CONFIG_VIDEO_LOGO +#define CONFIG_CONSOLE_TIME +#define CONFIG_CONSOLE_EXTRA_INFO +#define CONFIG_CONSOLE_CURSOR +#define CFG_CONSOLE_BLINK_COUNT 30000 /* approx. 2 HZ */ + +/* + * IDE/SCSI globals + */ +#ifndef __ASSEMBLY__ +extern unsigned int eltec_board; +extern unsigned int ata_reset_time; +extern unsigned int scsi_reset_time; +extern unsigned short scsi_dev_id; +extern unsigned int scsi_max_scsi_id; +extern unsigned char scsi_sym53c8xx_ccf; +#endif + +/* + * ATAPI Support (experimental) + */ +#define CONFIG_ATAPI +#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */ +#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ + +#define CFG_ATA_BASE_ADDR CFG_60X_PCI_IO_OFFSET /* base address */ +#define CFG_ATA_IDE0_OFFSET 0x1F0 /* default ide0 offste */ +#define CFG_ATA_IDE1_OFFSET 0x170 /* default ide1 offset */ +#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */ +#define CFG_ATA_REG_OFFSET 0 /* reg offset */ +#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */ + +#define ATA_RESET_TIME (ata_reset_time) + +#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ + +/* + * SCSI support (experimental) only SYM53C8xx supported + */ +#define CONFIG_SCSI_SYM53C8XX +#define CONFIG_SCSI_DEV_ID (scsi_dev_id) /* 875 or 860 */ +#define CFG_SCSI_SYM53C8XX_CCF (scsi_sym53c8xx_ccf) /* value for none 40 mhz clocks */ +#define CFG_SCSI_MAX_LUN 8 /* number of supported LUNs */ +#define CFG_SCSI_MAX_SCSI_ID (scsi_max_scsi_id) /* max SCSI ID (0-6) */ +#define CFG_SCSI_MAX_DEVICE (15 * CFG_SCSI_MAX_LUN) /* max. Target devices */ +#define CFG_SCSI_SPIN_UP_TIME (scsi_reset_time) + +/* + * Partion suppport + */ +#define CONFIG_DOS_PARTITION +#define CONFIG_MAC_PARTITION +#define CONFIG_ISO_PARTITION + +/* + * Winbond Configuration + */ +#define CFG_WINBOND_83C553 1 /* has a winbond bridge */ +#define CFG_USE_WINBOND_IDE 0 /* use winbond 83c553 internal ide */ +#define CFG_WINBOND_ISA_CFG_ADDR 0x80005800 /* pci-isa bridge config addr */ +#define CFG_WINBOND_IDE_CFG_ADDR 0x80005900 /* ide config addr */ + +/* + * NS87308 Configuration + */ +#define CFG_NS87308 /* Nat Semi super-io cntr on ISA bus */ +#define CFG_NS87308_BADDR_10 1 +#define CFG_NS87308_DEVS (CFG_NS87308_UART1 | \ + CFG_NS87308_UART2 | \ + CFG_NS87308_KBC1 | \ + CFG_NS87308_MOUSE | \ + CFG_NS87308_FDC | \ + CFG_NS87308_RARP | \ + CFG_NS87308_GPIO | \ + CFG_NS87308_POWRMAN | \ + CFG_NS87308_RTC_APC ) + +#define CFG_NS87308_PS2MOD +#define CFG_NS87308_GPIO_BASE 0x0220 +#define CFG_NS87308_PWMAN_BASE 0x0460 +#define CFG_NS87308_PMC2 0x00 /* SuperI/O clock source is 24MHz via X1 */ + +/* + * set up the NVRAM access registers + * NVRAM's controlled by the configurable CS line from the 87308 + */ +#define CFG_NS87308_CS0_BASE 0x0076 +#define CFG_NS87308_CS0_CONF 0x40 +#define CFG_NS87308_CS1_BASE 0x0070 +#define CFG_NS87308_CS1_CONF 0x1C +#define CFG_NS87308_CS2_BASE 0x0071 +#define CFG_NS87308_CS2_CONF 0x1C + +#define CONFIG_RTC_MK48T59 + +/* + * Initial BATs + */ +#if 1 + +#define CFG_IBAT0L 0 +#define CFG_IBAT0U 0 +#define CFG_DBAT0L CFG_IBAT1L +#define CFG_DBAT0U CFG_IBAT1U + +#define CFG_IBAT1L 0 +#define CFG_IBAT1U 0 +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +#define CFG_IBAT2L 0 +#define CFG_IBAT2U 0 +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +#define CFG_IBAT3L 0 +#define CFG_IBAT3U 0 +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +#else + +/* SDRAM */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_RW) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT1L +#define CFG_DBAT0U CFG_IBAT1U + +/* address range for flashes */ +#define CFG_IBAT1L (CFG_FLASH_BASE | BATL_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT1U (CFG_FLASH_BASE | BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* ISA IO space */ +#define CFG_IBAT2L (CFG_ISA_IO | BATL_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT2U (CFG_ISA_IO | BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +/* ISA memory space */ +#define CFG_IBAT3L (CFG_ISA_MEM | BATL_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT3U (CFG_ISA_MEM | BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +#endif + +/* + * Speed settings are board specific + */ +#ifndef __ASSEMBLY__ +extern unsigned long bab7xx_get_bus_freq (void); +extern unsigned long bab7xx_get_gclk_freq (void); +#endif +#define CFG_BUS_HZ bab7xx_get_bus_freq() +#define CFG_BUS_CLK CFG_BUS_HZ +#define CFG_CPU_CLK bab7xx_get_gclk_freq() + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * L2 Cache Configuration is board specific for BAB740/BAB750 + * Init values read from revision srom. + */ +#undef CFG_L2 +#define L2_INIT (L2CR_L2SIZ_HM | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ + L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) +#define L2_ENABLE (L2_INIT | L2CR_L2E) + +#define CFG_L2_BAB7xx + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +#define CONFIG_NET_MULTI /* Multi ethernet cards support */ +#define CONFIG_TULIP +#define CONFIG_TULIP_SELECT_MEDIA + +#endif /* __CONFIG_H */ diff --git a/include/configs/ELPPC.h b/include/configs/ELPPC.h new file mode 100644 index 0000000..a3b1296 --- /dev/null +++ b/include/configs/ELPPC.h @@ -0,0 +1,338 @@ +/* + * (C) Copyright 2002 ELTEC Elektronik AG + * Frank Gottschling + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include + +#undef DEBUG +#define GTREGREAD(x) 0xffffffff /* needed for debug */ + +/* + * High Level Configuration Options + * (easy to change) + */ + +/* these hardware addresses are pretty bogus, please change them to + suit your needs */ + +/* first ethernet */ +#define CONFIG_ETHADDR 00:00:5b:ee:de:ad + +#define CONFIG_IPADDR 192.168.0.105 +#define CONFIG_SERVERIP 192.168.0.100 + +#define CONFIG_ELPPC 1 /* this is an BAB740/BAB750 board */ + +#define CONFIG_BAUDRATE 9600 /* console baudrate */ + +#undef CONFIG_WATCHDOG + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp 1000000; " \ + "setenv bootargs root=ramfs console=ttyS00,9600 " \ + "ip=$(ipaddr):$(serverip):$(rootpath):$(gatewayip):" \ + "$(netmask):$(hostname):eth0:none; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +/* + * choose between COM1 and COM2 as serial console + */ +#define CONFIG_CONS_INDEX 1 + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x04000000 /* 0 ... 64 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x1000000 /* default load address */ + +#define CFG_HZ 1000 /* dec. freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +#define CFG_BOARD_ASM_INIT +#define CONFIG_MISC_INIT_R + +/* + * Address mapping scheme for the MPC107 mem controller is mapping B (CHRP) + */ +#undef CFG_ADDRESS_MAP_A + +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x40000000 + +#define CFG_PCI_MEM_BUS 0x80000000 +#define CFG_PCI_MEM_PHYS 0x80000000 +#define CFG_PCI_MEM_SIZE 0x7d000000 + +#define CFG_ISA_MEM_BUS 0x00000000 +#define CFG_ISA_MEM_PHYS 0xfd000000 +#define CFG_ISA_MEM_SIZE 0x01000000 + +#define CFG_PCI_IO_BUS 0x00800000 +#define CFG_PCI_IO_PHYS 0xfe800000 +#define CFG_PCI_IO_SIZE 0x00400000 + +#define CFG_ISA_IO_BUS 0x00000000 +#define CFG_ISA_IO_PHYS 0xfe000000 +#define CFG_ISA_IO_SIZE 0x00800000 + +/* driver defines FDC,IDE,... */ +#define CFG_ISA_IO_BASE_ADDRESS CFG_ISA_IO_PHYS +#define CFG_ISA_IO CFG_ISA_IO_PHYS +#define CFG_60X_PCI_IO_OFFSET CFG_ISA_IO_PHYS + +/* + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 + +#define CFG_USR_LED_BASE 0x78000000 +#define CFG_NVRAM_BASE 0xff000000 +#define CFG_UART_BASE 0xff400000 +#define CFG_FLASH_BASE 0xfff00000 + +#define MPC107_EUMB_ADDR 0xfce00000 +#define MPC107_EUMB_PI 0xfce41090 +#define MPC107_EUMB_GCR 0xfce41020 +#define MPC107_EUMB_IACKR 0xfce600a0 +#define MPC107_I2C_ADDR 0xfce03000 + +/* + * Definitions for initial stack pointer and data area + */ +#define CFG_INIT_RAM_ADDR 0x00fd0000 /* above the memtest region */ +#define CFG_INIT_RAM_END 0x4000 +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for init data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* + * Flash mapping/organization on the MPC10x. + */ +#define FLASH_BASE0_PRELIM 0xff800000 +#define FLASH_BASE1_PRELIM 0xffc00000 + +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ +#define CFG_JFFS2_NUM_BANKS 2 /* ! second bank contains U-Boot */ + +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN 0x20000 /* Reserve 128 kB for malloc() */ +#undef CFG_MEMTEST + +/* + * Environment settings + */ +#define CONFIG_ENV_OVERWRITE +#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ +#define CFG_NVRAM_SIZE 0x800 /* NVRAM size (2kB) */ +#define CFG_ENV_SIZE 0x400 /* Size of Environment vars (1kB) */ +#define CFG_ENV_ADDR 0x0 +#define CFG_ENV_MAP_ADRS 0xff000000 +#define CFG_NV_SROM_COPY_ADDR (CFG_ENV_ADDR + CFG_ENV_SIZE) +#define CFG_NVRAM_ACCESS_ROUTINE /* only byte accsess alowed */ +#define CFG_SROM_SIZE 0x100 /* shadow of revision info is in nvram */ + +/* + * Serial devices + */ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK 24000000 +#define CFG_NS16550_COM1 (CFG_UART_BASE + 0) +#define CFG_NS16550_COM2 (CFG_UART_BASE + 8) + +/* + * PCI stuff + */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* pci plug-and-play */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO +#undef CONFIG_PCI_SCAN_SHOW + +/* + * Optional Video console (graphic: SMI LynxEM) + */ +#define CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define VIDEO_KBD_INIT_FCT (simple_strtol (getenv("console"), NULL, 10)) +#define VIDEO_TSTC_FCT serial_tstc +#define VIDEO_GETC_FCT serial_getc + +#define CONFIG_VIDEO_SMI_LYNXEM +#define CONFIG_VIDEO_LOGO +#define CONFIG_CONSOLE_EXTRA_INFO + +/* + * Initial BATs + */ +#if 1 + +#define CFG_IBAT0L 0 +#define CFG_IBAT0U 0 +#define CFG_DBAT0L CFG_IBAT1L +#define CFG_DBAT0U CFG_IBAT1U + +#define CFG_IBAT1L 0 +#define CFG_IBAT1U 0 +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +#define CFG_IBAT2L 0 +#define CFG_IBAT2U 0 +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +#define CFG_IBAT3L 0 +#define CFG_IBAT3U 0 +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +#else + +/* SDRAM */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_RW) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT1L +#define CFG_DBAT0U CFG_IBAT1U + +/* address range for flashes */ +#define CFG_IBAT1L (CFG_FLASH_BASE | BATL_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT1U (CFG_FLASH_BASE | BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* ISA IO space */ +#define CFG_IBAT2L (CFG_ISA_IO | BATL_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT2U (CFG_ISA_IO | BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +/* ISA memory space */ +#define CFG_IBAT3L (CFG_ISA_MEM | BATL_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT3U (CFG_ISA_MEM | BATU_BL_16M | BATU_VS | BATU_VP) +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +#endif + +/* + * Speed settings are board specific + */ +#define CFG_BUS_HZ 100000000 +#define CFG_CPU_CLK 400000000 +#define CFG_BUS_CLK CFG_BUS_HZ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * L2CR setup -- make sure this is right for your board! + * look in include/mpc74xx.h for the defines used here + */ + +#define CFG_L2 + +#if 1 +#define L2_INIT 0 /* cpu 750 CXe*/ +#else +#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ + L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) +#endif +#define L2_ENABLE (L2_INIT | L2CR_L2E) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_NET_MULTI /* Multi ethernet cards support */ +#define CONFIG_EEPRO100 +#define CONFIG_EEPRO100_SROM_WRITE + +#endif /* __CONFIG_H */ diff --git a/include/configs/ERIC.h b/include/configs/ERIC.h new file mode 100644 index 0000000..9f6baf7 --- /dev/null +++ b/include/configs/ERIC.h @@ -0,0 +1,372 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405GP 1 /* This is a PPC405 CPU */ +#define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_ERIC 1 /* ...on a ERIC board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* run board_pre_init() */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +#if 1 +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#endif +#if 0 +#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ +#endif +#if 0 +#define CFG_ENV_IS_IN_EEPROM 1 /* use I2C RTC X1240 for environment vars */ +#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars */ +#endif /* total size of a X1240 is 2048 bytes */ + +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_EEPROM_ADDR 0x57 /* X1240 has two I2C slave addresses, one for EEPROM */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* address length for the eeprom */ +#define CONFIG_I2C_RTC 1 /* we have a Xicor X1240 RTC */ +#define CFG_I2C_RTC_ADDR 0x6F /* and one for RTC */ + +#ifdef CFG_ENV_IS_IN_FLASH +#undef CFG_ENV_IS_IN_NVRAM +#undef CFG_ENV_IS_IN_EEPROM +#else +#ifdef CFG_ENV_IS_IN_NVRAM +#undef CFG_ENV_IS_IN_FLASH +#undef CFG_ENV_IS_IN_EEPROM +#else +#ifdef CFG_ENV_IS_IN_EEPROM +#undef CFG_ENV_IS_IN_NVRAM +#undef CFG_ENV_IS_IN_FLASH +#endif +#endif +#endif + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#if 1 +#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */ +#else +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ +#endif + +#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs " \ + "nfsroot=192.168.1.2:/eric_root_devel " \ + "ip=192.168.1.22:192.168.1.2" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 1 /* PHY address */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_PCI | \ + CFG_CMD_IRQ | \ + CFG_CMD_ENV | \ + CFG_CMD_FLASH) + +/* + * #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | \ + * CFG_CMD_KGDB | CFG_CMD_I2C | CFG_CMD_EEPROM | \ + * CFG_CMD_ENV | CFG_CMD_FLASH) + */ + +/* CFG_CMD_ENV est definie */ +/* ((CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_KGDB) & ~(CFG_CMD_ENV)) + */ +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#undef CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_EXT_SERIAL_CLOCK 14318180 + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ + 57600, 115200, 230400, 460800, 921600 } + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ +#undef CONFIG_PCI_PNP /* no pci plug-and-play */ + /* resource configuration */ + +#define CFG_PCI_SUBSYS_VENDORID 0x1743 /* PCI Vendor ID: Peppercon AG */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: 405GP */ +#define CFG_PCI_PTM1LA 0xFFFC0000 /* point to flash */ +#define CFG_PCI_PTM1MS 0xFFFFF001 /* 4kB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ +#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ +#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ + +/*----------------------------------------------------------------------- + * External peripheral base address + *----------------------------------------------------------------------- + */ +/* Bank 0 - Flash/SRAM 0xFF000000 16MB 16 Bit */ +/* Bank 1 - NVRAM/RTC 0xF0000000 1MB 8 Bit */ +/* Bank 2 - A/D converter 0xF0100000 1MB 8 Bit */ +/* Bank 3 - Ethernet PHY Reset 0xF0200000 1MB 8 Bit */ +/* Bank 4 - PC-MIP PRSNT1# 0xF0300000 1MB 8 Bit */ +/* Bank 5 - PC-MIP PRSNT2# 0xF0400000 1MB 8 Bit */ +/* Bank 6 - CPU LED0 0xF0500000 1MB 8 Bit */ +/* Bank 7 - CPU LED1 0xF0600000 1MB 8 Bit */ + +/* ----------------------------------------------------------------------- */ +/* Memory Bank 0 (Flash) initialization */ +/* ----------------------------------------------------------------------- */ +#define CS0_AP 0x9B015480 +#define CS0_CR 0xFF87A000 /* BAS=0xFF8,BS=(8MB),BU=0x3(R/W), BW=(16 bits) */ +/* ----------------------------------------------------------------------- */ +/* Memory Bank 1 (NVRAM/RTC) initialization */ +/* ----------------------------------------------------------------------- */ +#define CS1_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ +#define CS1_CR 0xF0018000 /* BAS=0xF00,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ + /* ----------------------------------------------------------------------- */ + /* Memory Bank 2 (A/D converter) initialization */ + /* ----------------------------------------------------------------------- */ +#define CS2_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ +#define CS2_CR 0xF0118000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ +/* ----------------------------------------------------------------------- */ +/* Memory Bank 3 (Ethernet PHY Reset) initialization */ +/* ----------------------------------------------------------------------- */ +#define CS3_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ +#define CS3_CR 0xF0218000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ +/* ----------------------------------------------------------------------- */ +/* Memory Bank 4 (PC-MIP PRSNT1#) initialization */ +/* ----------------------------------------------------------------------- */ +#define CS4_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ +#define CS4_CR 0xF0318000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ +/* ----------------------------------------------------------------------- */ +/* Memory Bank 5 (PC-MIP PRSNT2#) initialization */ +/* ----------------------------------------------------------------------- */ +#define CS5_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ +#define CS5_CR 0xF0418000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ +/* ----------------------------------------------------------------------- */ +/* Memory Bank 6 (CPU LED0) initialization */ +/* ----------------------------------------------------------------------- */ +#define CS6_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ +#define CS6_CR 0xF0518000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ +/* ----------------------------------------------------------------------- */ +/* Memory Bank 7 (CPU LED1) initialization */ +/* ----------------------------------------------------------------------- */ +#define CS7_AP 0x02815480 /* WT=1, OEN=0x1,WBN=0x1,WBF=0x1,TH=0x2,RE=0, */ +#define CS7_CR 0xF0618000 /* BAS=0xF01,BS=(1MB),BU=0x3(R/W), BW=(8 bits) */ + +#define CFG_NVRAM_REG_BASE_ADDR 0xF0000000 +#define CFG_RTC_REG_BASE_ADDR (0xF0000000 + 0x7F8) +#define CFG_ADC_REG_BASE_ADDR 0xF0100000 +#define CFG_PHYRES_REG_BASE_ADDR 0xF0200000 +#define CFG_PRSNT1_REG_BASE_ADDR 0xF0300000 +#define CFG_PRSNT2_REG_BASE_ADDR 0xF0400000 +#define CFG_LED0_REG_BASE_ADDR 0xF0500000 +#define CFG_LED1_REG_BASE_ADDR 0xF0600000 + + +/* SDRAM CONFIG */ +#define CFG_SDRAM_MANUALLY 1 +#define CFG_SDRAM_SINGLE_BANK 1 + +#ifdef CFG_SDRAM_MANUALLY +/*----------------------------------------------------------------------- + * Set MB0CF for bank 0. (0-32MB) Address Mode 4 since 12x8(2) + *----------------------------------------------------------------------*/ +#define MB0CF 0x00062001 /* 32MB @ 0 */ +/*----------------------------------------------------------------------- + * Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2) + *----------------------------------------------------------------------*/ +#ifdef CFG_SDRAM_SINGLE_BANK +#define MB1CF 0x0 /* 0MB @ 32MB */ +#else +#define MB1CF 0x02062001 /* 32MB @ 32MB */ +#endif +/*----------------------------------------------------------------------- + * Set MB2CF for bank 2. off + *----------------------------------------------------------------------*/ +#define MB2CF 0x0 /* 0MB */ +/*----------------------------------------------------------------------- + * Set MB3CF for bank 3. off + *----------------------------------------------------------------------*/ +#define MB3CF 0x0 /* 0MB */ + +#define SDTR_100 0x0086400D +#define RTR_100 0x05F0 +#define SDTR_66 0x00854006 /* orig U-Boot-wallnut says 0x00854006 */ +#define RTR_66 0x03f8 + +#endif /* CFG_SDRAM_MANUALLY */ + + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_SIZE 32 +#define CFG_FLASH_BASE 0xFF800000 /* 8 MByte Flash */ +#define CFG_MONITOR_BASE 0xFFFE0000 /* last 128kByte within Flash */ +/*#define CFG_MONITOR_LEN (192 * 1024)*/ /* Reserve 196 kB for Monitor */ +#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ +#define CFG_FLASH_16BIT 1 /* Rom 16 bit data bus */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +/* BEG ENVIRONNEMENT FLASH */ +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE (128*1024) + +#if 0 /* force ENV to be NOT embedded */ +#define CFG_ENV_ADDR 0xfffa0000 +#else /* force ENV to be embedded */ +#define CFG_ENV_SIZE (2 * 1024) /* Total Size of Environment Sector 2k */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN - CFG_ENV_SIZE - 0x10) /* let space for reset vector */ +/* #define CFG_ENV_ADDR (CFG_MONITOR_BASE)*/ +#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE) +#endif + +#endif +/* END ENVIRONNEMENT FLASH */ +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CFG_NVRAM_BASE_ADDR CFG_NVRAM_REG_BASE_ADDR /* NVRAM base address */ +#define CFG_NVRAM_SIZE 0x7F8 /* NVRAM size 2kByte - 8 Byte for RTC */ + +#ifdef CFG_ENV_IS_IN_NVRAM +#define CFG_ENV_SIZE 0x7F8 /* Size of Environment vars */ +#define CFG_ENV_ADDR \ + (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ +#endif +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 8MB */ +#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ + + +/* Configuration Port location */ +/* #define CONFIG_PORT_ADDR 0xF0000500 */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */ +#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ diff --git a/include/configs/ETX094.h b/include/configs/ETX094.h new file mode 100644 index 0000000..9d7c868 --- /dev/null +++ b/include/configs/ETX094.h @@ -0,0 +1,356 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC850 1 /* This is a MPC850 CPU */ +#define CONFIG_ETX094 1 /* ...on a ETX_094 board */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 57600 +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_FLASH_16BIT /* for board with 16bit wide flash */ +#undef SB_ETX094 /* only for SB-Board with 16MB SDRAM */ +#define CONFIG_BOOTP_RANDOM_DELAY /* graceful BOOTP recovery mode */ + +#define CONFIG_ETHADDR 08:00:06:00:00:00 + +#ifdef CONFIG_ETHADDR +#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 /* default MAC can be overwritten once */ +#endif + +#undef CONFIG_BOOTARGS +#define CONFIG_RAMBOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/ram rw ramdisk_size=4690 " \ + "U-Boot_version=U-Boot-1.0.x-Date " \ + "panic=1 " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" +#define CONFIG_NFSBOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(nfsip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" +#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#define CONFIG_WATCHDOG 1 /* watchdog enabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0300000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#ifdef DEBUG +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#ifdef CONFIG_FLASH_16BIT +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */ +#else +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#endif + +/*----------------------------------------------------------------------- + * Hardware Information Block + */ +#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 1, CSNT = 0, SCY = 2, EHTR = 0 */ +#define CFG_OR_TIMING_FLASH (OR_ACS_DIV2 | OR_BI | \ + OR_SCY_2_CLK | OR_TRLX ) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) + +#ifdef CONFIG_FLASH_16BIT /* 16 bit data port */ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16) +#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16) +#else /* 32 bit data port */ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_32) +#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V | BR_PS_32) +#endif /* CONFIG_FLASH_16BIT */ + +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM CFG_OR0_PRELIM + +/* + * BR2/3 and OR2/3 (SDRAM) + * + */ +#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */ +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM 0x00000A00 + +#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) +#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +#define CFG_OR3_PRELIM CFG_OR2_PRELIM +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 23 /* start with divider for 100 MHz */ + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_1X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_1X) + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/IP860.h b/include/configs/IP860.h new file mode 100644 index 0000000..6fa2d19 --- /dev/null +++ b/include/configs/IP860.h @@ -0,0 +1,459 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC860 1 /* This is a MPC860 CPU */ +#define CONFIG_IP860 1 /* ...on a IP860 board */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" \ +"\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 $(filesize)\0" + +#define CONFIG_ETHADDR 00:30:bf:01:02:d2 +#define CONFIG_IPADDR 10.0.0.5 +#define CONFIG_SERVERIP 10.0.0.2 + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + + +# define CFG_I2C_SPEED 50000 +# define CFG_I2C_SLAVE 0xFE +# define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ +# define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_BEDBUG | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM) + +#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT + +/*----------------------------------------------------------------------*/ + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/*----------------------------------------------------------------------*/ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xF1000000 /* Non-standard value!! */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x10000000 +#ifdef DEBUG +#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ +#else +#if 0 /* need more space for I2C tests */ +#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (256 << 10) +#endif +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 124 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#undef CFG_ENV_IS_IN_FLASH +#undef CFG_ENV_IS_IN_NVRAM +#undef CFG_ENV_IS_IN_NVRAM +#undef DEBUG_I2C +#define CFG_ENV_IS_IN_EEPROM + +#ifdef CFG_ENV_IS_IN_NVRAM +#define CFG_ENV_ADDR 0x20000000 /* use SRAM */ +#define CFG_ENV_SIZE (16<<10) /* use 16 kB */ +#endif /* CFG_ENV_IS_IN_NVRAM */ + +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_OFFSET 512 /* Leave 512 bytes free for other data */ +#define CFG_ENV_SIZE 1536 /* Use remaining space */ +#endif /* CFG_ENV_IS_IN_EEPROM */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + * +0x0004 + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * +0x0000 => 0x80600800 + */ +#define CFG_SIUMCR (SIUMCR_EARB | SIUMCR_EARP0 | \ + SIUMCR_DBGC11 | SIUMCR_MLRC10) + +/*----------------------------------------------------------------------- + * Clock Setting - the IP860 has no 32kHz clock, so automatic detection fails + *----------------------------------------------------------------------- + */ +#define CONFIG_8xx_GCLK_FREQ 50000000 + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + * +0x0200 => 0x00C2 + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + * +0x0240 => 0x0082 + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit, set PLL multiplication factor ! + */ +/* +0x0286 => was: 0x0000D000 */ +#define CFG_PLPRCR \ + ( PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ + /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ + PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ + ) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_COM00 | SCCR_TBS | \ + SCCR_RTDIV | SCCR_RTSEL | \ + /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ + SCCR_EBDF00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000 | \ + SCCR_DFNH000) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +/* +0x0220 => 0x00C3 */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration Register 19-4 + *----------------------------------------------------------------------- + */ +/* +0x09C4 => TIMEP=1 */ +#define CFG_RCCR 0x0100 + +/*----------------------------------------------------------------------- + * RMDS - RISC Microcode Development Support Control Register + *----------------------------------------------------------------------- + */ +#define CFG_RMDS 0 + +/*----------------------------------------------------------------------- + * DER - Debug Event Register + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + */ + +/* + * MAMR settings for SDRAM - 16-14 + * => 0xC3804114 + */ + +/* periodic timer for refresh */ +#define CFG_MAMR_PTA 0xC3 + +#define CFG_MAMR ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* + * BR1 and OR1 (FLASH) + */ +#define FLASH_BASE 0x10000000 /* FLASH bank #0 */ + +/* used to re-map FLASH + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +/* allow for max 8 MB of Flash */ +#define CFG_REMAP_OR_AM 0xFF800000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ + +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +/* 16 bit, bank valid */ +#define CFG_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V ) + +#define CFG_OR1_PRELIM CFG_OR0_PRELIM +#define CFG_BR1_PRELIM CFG_BR0_PRELIM + +/* + * BR2/OR2 - SDRAM + */ +#define SDRAM_BASE 0x00000000 /* SDRAM bank */ +#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ +#define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */ + +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ + +#define CFG_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) +#define CFG_BR2 ((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* + * BR3/OR3 - SRAM (16 bit) + */ +#define SRAM_BASE 0x20000000 +#define CFG_OR3 0xFFF00130 /* BI/SCY = 5/TRLX (internal) */ +#define CFG_BR3 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) +#define SRAM_SIZE (1 + (~(CFG_OR3 & BR_BA_MSK))) +#define CFG_OR3_PRELIM CFG_OR3 /* Make sure to map early */ +#define CFG_BR3_PRELIM CFG_BR3 /* in case it's used for ENV */ + +/* + * BR4/OR4 - Board Control & Status (8 bit) + */ +#define BCSR_BASE 0xFC000000 +#define CFG_OR4 0xFFFF0120 /* BI (internal) */ +#define CFG_BR4 ((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) + +/* + * BR5/OR5 - IP Slot A/B (16 bit) + */ +#define IP_SLOT_BASE 0x40000000 +#define CFG_OR5 0xFE00010C /* SETA/TRLX/BI/ SCY=0 (external) */ +#define CFG_BR5 ((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) + +/* + * BR6/OR6 - VME STD (16 bit) + */ +#define VME_STD_BASE 0xFE000000 +#define CFG_OR6 0xFF00010C /* SETA/TRLX/BI/SCY=0 (external) */ +#define CFG_BR6 ((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) + +/* + * BR7/OR7 - SHORT I/O + RTC + IACK (16 bit) + */ +#define VME_SHORT_BASE 0xFF000000 +#define CFG_OR7 0xFF00010C /* SETA/TRLX/BI/ SCY=0 (external) */ +#define CFG_BR7 ((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) + +/*----------------------------------------------------------------------- + * Board Control and Status Region: + *----------------------------------------------------------------------- + */ +#ifndef __ASSEMBLY__ +typedef struct ip860_bcsr_s { + unsigned char shmem_addr; /* +00 shared memory address register */ + unsigned char reserved0; + unsigned char mbox_addr; /* +02 mailbox address register */ + unsigned char reserved1; + unsigned char vme_int_mask; /* +04 VME Bus interrupt mask register */ + unsigned char reserved2; + unsigned char vme_int_pend; /* +06 VME interrupt pending register */ + unsigned char reserved3; + unsigned char bd_int_mask; /* +08 board interrupt mask register */ + unsigned char reserved4; + unsigned char bd_int_pend; /* +0A board interrupt pending register */ + unsigned char reserved5; + unsigned char bd_ctrl; /* +0C board control register */ + unsigned char reserved6; + unsigned char bd_status; /* +0E board status register */ + unsigned char reserved7; + unsigned char vme_irq; /* +10 VME interrupt request register */ + unsigned char reserved8; + unsigned char vme_ivec; /* +12 VME interrupt vector register */ + unsigned char reserved9; + unsigned char cli_mbox; /* +14 clear mailbox irq */ + unsigned char reservedA; + unsigned char rtc; /* +16 RTC control register */ + unsigned char reservedB; + unsigned char mbox_data; /* +18 mailbox read/write register */ + unsigned char reservedC; + unsigned char wd_trigger; /* +1A Watchdog trigger register */ + unsigned char reservedD; + unsigned char rmw_req; /* +1C RMW request register */ +} ip860_bcsr_t; +#endif /* __ASSEMBLY__ */ + +/*----------------------------------------------------------------------- + * Board Control Register: bd_ctrl (Offset 0x0C) + *----------------------------------------------------------------------- + */ +#define BD_CTRL_IPLSE 0x80 /* IP Slot Long Select Enable */ +#define BD_CTRL_WDOGE 0x40 /* Watchdog Enable */ +#define BD_CTRL_FLWE 0x20 /* Flash Write Enable */ +#define BD_CTRL_RWDN 0x10 /* VMEBus Requester Release When Done Enable */ + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h new file mode 100644 index 0000000..6b7079e --- /dev/null +++ b/include/configs/IPHASE4539.h @@ -0,0 +1,354 @@ +/* + * (C) Copyright 2002 Wolfgang Grandegger + * + * This file is based on similar values for other boards found in + * other U-Boot config files, mainly tqm8260.h and mpc8260ads.h. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Config header file for a Interphase 4539 PMC, 64 MB SDRAM, 4MB Flash. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG /* General debug */ + +/*----------------------------------------------------------------------- + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_IPHASE4539 1 /* ...on a Interphase 4539 PMC */ + +/*----------------------------------------------------------------------- + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +/*----------------------------------------------------------------------- + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 3 /* which channel for ether */ + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) + +/*----------------------------------------------------------------------- + * - Rx-CLK is CLK14 + * - Tx-CLK is CLK16 + * - Select bus for bd/buffers (see 28-13) + * - Half duplex + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK14 | CMXFCR_TF3CS_CLK16) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */ + +/* other options */ + +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ +#define CONFIG_BAUDRATE 19200 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE) + +/* + * select i2c support configuration + * + * Supported configurations are {none, software, hardware} drivers. + * If the software driver is chosen, there are some additional + * configuration items that the driver uses to drive the port pins. + */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ +#ifdef CONFIG_SOFT_I2C +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ + +#define CONFIG_COMMANDS CONFIG_CMD_DFL + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */ +#define CONFIG_BOOTARGS "root=/dev/ram rw" + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ +#endif + +#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passed to Linux in MHz */ + /* for versions < 2.4.5-pre5 */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_RESET_ADDRESS 0x04400000 + +#define CONFIG_MISC_INIT_R 1 /* We need misc_init_r() */ + +/*----------------------------------------------------------------------- + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration (Setup by the + * startup code). Please note that CFG_SDRAM_BASE _must_ start at 0. + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFF800000 + +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 64 /* max num of sects on one chip */ +#define CFG_MAX_FLASH_SIZE (CFG_MAX_FLASH_SECT * 0x10000) /* 4 MB */ + +#define CFG_FLASH_ERASE_TOUT 2400000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +/* Environment in FLASH, there is little space left in Serial EEPROM */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SECT_SIZE 0x10000 /* We use one complete sector */ +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x10000) /* 2. sector */ + + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CFG_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CFG_SIUMCR. + */ +#define CFG_HRCW_MASTER ( ( HRCW_BPS01 | HRCW_EBM ) |\ + ( HRCW_L2CPC10 | HRCW_ISB110 ) |\ + ( HRCW_MMR11 | HRCW_APPC10 ) |\ + ( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \ + ) /* 0x14863245 */ + +/* no slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 /* We keep original value */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CFG_BCR 0xA01C0000 + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#define CFG_SIUMCR 0X4205C000 + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined (CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + *----------------------------------------------------------------------- + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CFG_SCCR 0 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/*----------------------------------------------------------------------- + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 64 bit FLASH + * 1 60x SDRAM 64 bit SDRAM + */ + +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) | 0x0801) +#define CFG_OR0_PRELIM 0xFF800882 +#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) | 0x0041) +#define CFG_OR1_PRELIM 0xF8002CD0 + +#define CFG_PSDMR 0x404A241A +#define CFG_MPTPR 0x00007400 +#define CFG_PSRT 0x00000007 + +#endif /* __CONFIG_H */ diff --git a/include/configs/MBX.h b/include/configs/MBX.h new file mode 100644 index 0000000..e62d36c --- /dev/null +++ b/include/configs/MBX.h @@ -0,0 +1,307 @@ +/* + * (C) Copyright 2000 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * Configuation settings for the MBX8xx board. + * + * ----------------------------------------------------------------- + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +/* + * Changed 2002-10-01 + * Added PCMCIA defines mostly taken from other U-Boot boards that + * have PCMCIA already working. If you find any bugs, incorrect assumptions + * feel free to fix them yourself and submit a patch. + * Rod Boyce + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#undef CFG_HUSH_PARSER /* Hush parse for U-Boot */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Physical memory map as defined by the MBX PGM + */ +#define CFG_IMMR 0xFA200000 /* Internal Memory Mapped Register*/ +#define CFG_NVRAM_BASE 0xFA000000 /* NVRAM */ +#define CFG_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */ +#define CFG_CSR_BASE 0xFA100000 /* Control/Status Registers */ +#define CFG_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */ +#define CFG_PCIMEM_OR 0xA0000108 +#define CFG_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */ +#define CFG_PCIBRIDGE_OR 0xFFFF0108 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2f00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */ +#define CFG_INIT_VPD_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_VPD_SIZE) +#define CFG_INIT_SP_OFFSET (CFG_INIT_VPD_OFFSET-8) + +/*----------------------------------------------------------------------- + * Offset in DPMEM where we keep the VPD data + */ +#define CFG_DPRAMVPD (CFG_INIT_VPD_OFFSET - 0x2000) + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xfe000000 +#ifdef DEBUG +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#endif +#undef CFG_MONITOR_BASE /* 0x200000 to run U-Boot from RAM */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +/*----------------------------------------------------------------------- + * NVRAM Configuration + * + * Note: the MBX is special because there is already a firmware on this + * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we + * access the NVRAM at the offset 0x1000. + */ +#define CFG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */ +#define CFG_ENV_ADDR (CFG_NVRAM_BASE + 0x1000) +#define CFG_ENV_SIZE 0x1000 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +/* #define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC11 | SIUMCR_SEME | SIUMCR_BSC ) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL) +#define CFG_SCCR SCCR_TBS + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +#define CFG_PCMCIA_INTERRUPT SIU_LEVEL6 + +#define CONFIG_PCMCIA_SLOT_A 1 + + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +/*----------------------------------------------------------------------- + * Debug Entry Mode + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/MHPC.h b/include/configs/MHPC.h new file mode 100644 index 0000000..78caafd --- /dev/null +++ b/include/configs/MHPC.h @@ -0,0 +1,371 @@ +/* + * (C) Copyright 2001 + * Frank Gottschling, ELTEC Elektronik AG, fgottschling@eltec.de + * + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * Configuation settings for the miniHiPerCam. + * + * ----------------------------------------------------------------- + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ +#define CONFIG_MHPC 1 /* on a miniHiPerCam */ +#define CONFIG_BOARD_PRE_INIT 1 /* do special hardware init. */ +#define CONFIG_MISC_INIT_R 1 + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_SPEED +#undef CONFIG_8xx_CONS_SMC1 +#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */ +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_ETHADDR 00:00:5b:ee:de:ad + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ + "bootm" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#undef CONFIG_UCODE_PATCH + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CFG_I2C_SPEED 50000 +#define CFG_I2C_SLAVE 0xFE +#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C04 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +#define LCD_VIDEO_ADDR (SDRAM_MAX_SIZE-SDRAM_RES_SIZE) +#define LCD_VIDEO_SIZE SDRAM_RES_SIZE /* 2MB */ +#define LCD_VIDEO_COLS 640 +#define LCD_VIDEO_ROWS 480 +#define LCD_VIDEO_FG 255 +#define LCD_VIDEO_BG 0 + +#undef CONFIG_VIDEO /* test only ! s.a devices.c and 8xx */ +#define CONFIG_CFB_CONSOLE /* framebuffer console with std input */ +#define CONFIG_VIDEO_LOGO + +#define VIDEO_KBD_INIT_FCT 0 /* no KBD dev on MHPC - use serial */ +#define VIDEO_TSTC_FCT serial_tstc +#define VIDEO_GETC_FCT serial_getc + +#define CONFIG_BR0_WORKAROUND 1 + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DATE | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_REGINFO ) + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x300000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Physical memory map + */ +#define CFG_IMMR 0xFFF00000 /* Internal Memory Mapped Register*/ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xfe000000 + +#define CFG_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */ +#undef CFG_MONITOR_BASE /* to run U-Boot from RAM */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ +#define CFG_JFFS2_NUM_BANKS 1 /* one flash only */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map- for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET CFG_MONITOR_LEN /* Offset of Environment */ +#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_SEME) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 12-18 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define MPC8XX_SPEED 50000000L +#define MPC8XX_XIN 5000000L /* ref clk */ +#define MPC8XX_FACT (MPC8XX_SPEED/MPC8XX_XIN) +#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ + +#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL) /* SCCR_EBDF11 */ +#define CFG_SCCR (SCCR_TBS | SCCR_DFLCD001) + + +/*----------------------------------------------------------------------- + * MAMR settings for SDRAM - 16-14 + * => 0xC080200F + *----------------------------------------------------------------------- + * periodic timer for refresh + */ +#define CFG_MAMR_PTA 0xC0 +#define CFG_MAMR ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | MAMR_G0CLA_A11 | MAMR_TLFA_MSK) + +/* + * BR0 and OR0 (FLASH) used to re-map FLASH + */ + +/* allow for max 8 MB of Flash */ +#define FLASH_BASE 0xFE000000 /* FLASH bank #0*/ +#define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0*/ +#define CFG_REMAP_OR_AM 0xFF800000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ + +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_8_CLK) /* (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)*/ + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_GPCM | BR_V ) + +/* + * BR1 and OR1 (SDRAM) + */ +#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */ +#define SDRAM_RES_SIZE 0x00200000 /* 2 MB for framebuffer */ + +/* SDRAM timing: drive GPL5 high on first cycle */ +#define CFG_OR_TIMING_SDRAM (OR_G5LS) + +#define CFG_OR1_PRELIM ((~(SDRAM_MAX_SIZE)+1)| CFG_OR_TIMING_SDRAM ) +#define CFG_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* + * BR2/OR2 - DIMM + */ +#define CFG_OR2 (OR_ACS_DIV4) +#define CFG_BR2 (BR_MS_UPMA) + +/* + * BR3/OR3 - DIMM + */ +#define CFG_OR3 (OR_ACS_DIV4) +#define CFG_BR3 (BR_MS_UPMA) + +/* + * BR4/OR4 + */ +#define CFG_OR4 0 +#define CFG_BR4 0 + +/* + * BR5/OR5 + */ +#define CFG_OR5 0 +#define CFG_BR5 0 + +/* + * BR6/OR6 + */ +#define CFG_OR6 0 +#define CFG_BR6 0 + +/* + * BR7/OR7 + */ +#define CFG_OR7 0 +#define CFG_BR7 0 + + +/*----------------------------------------------------------------------- + * Debug Entry Mode + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h new file mode 100644 index 0000000..f6d186f --- /dev/null +++ b/include/configs/MPC8260ADS.h @@ -0,0 +1,267 @@ +/* + * (C) Copyright 2001 + * Stuart Hughes + * This file is based on similar values for other boards found in other + * U-Boot config files, and some that I found in the mpc8260ads manual. + * + * Note: my board is a PILOT rev. + * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Config header file for a MPC8260ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_MPC8260ADS 1 /* ...on motorola ads board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +/* allow serial and ethaddr to be overwritten */ +#define CONFIG_ENV_OVERWRITE + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ + +#if (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers (see 28-13) + * - Half duplex + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) +# define CFG_CPMFCR_RAMTYPE 0 +# define CFG_FCC_PSMR 0 + +#endif /* CONFIG_ETHER_INDEX */ + +/* other options */ +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + + +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \ + CFG_CMD_BEDBUG | \ + CFG_CMD_BSP | \ + CFG_CMD_DATE | \ + CFG_CMD_DOC | \ + CFG_CMD_DTT | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_FDC | \ + CFG_CMD_HWFLOW | \ + CFG_CMD_IDE | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_KGDB | \ + CFG_CMD_MII | \ + CFG_CMD_PCI | \ + CFG_CMD_PCMCIA | \ + CFG_CMD_SCSI | \ + CFG_CMD_VFD | \ + CFG_CMD_USB ) ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */ +#define CONFIG_BOOTARGS "root=/dev/ram rw" + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ +#endif + +#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + /* for versions < 2.4.5-pre5 */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +#define CFG_FLASH_BASE 0xff800000 +#define FLASH_BASE 0xff800000 +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_MAX_FLASH_SECT 32 /* max num of sects on one chip */ +#define CFG_FLASH_SIZE 8 +#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ + +/* this is stuff came out of the Motorola docs */ +#define CFG_DEFAULT_IMMR 0x0F010000 + +#define CFG_IMMR 0x04700000 +#define CFG_BCSR 0x04500000 +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_LSDRAM_BASE 0x04000000 + +#define RS232EN_1 0x02000002 +#define RS232EN_2 0x01000001 +#define FETHIEN 0x08000008 +#define FETH_RST 0x04000004 + +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + + +/* 0x0EA28205 */ +#define CFG_HRCW_MASTER ( ( HRCW_BPS11 | HRCW_CIP ) |\ + ( HRCW_L2CPC10 | HRCW_DPPC10 | HRCW_ISB010 ) |\ + ( HRCW_BMS | HRCW_APPC10 ) |\ + ( HRCW_MODCK_H0101 ) \ + ) + +/* no slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#ifndef CFG_RAMBOOT +# define CFG_ENV_IS_IN_FLASH 1 +# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +# define CFG_ENV_SECT_SIZE 0x40000 +#else +# define CFG_ENV_IS_IN_NVRAM 1 +# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +# define CFG_ENV_SIZE 0x200 +#endif /* CFG_RAMBOOT */ + + +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + + +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE ) + +#define CFG_HID2 0 + +#define CFG_SYPCR 0xFFFFFFC3 +#define CFG_BCR 0x100C0000 +#define CFG_SIUMCR 0x0A200000 +#define CFG_SCCR 0x00000000 +#define CFG_BR0_PRELIM 0xFF801801 +#define CFG_OR0_PRELIM 0xFF800836 +#define CFG_BR1_PRELIM 0x04501801 +#define CFG_OR1_PRELIM 0xFFFF8010 + +#define CFG_RMR 0 +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) +#define CFG_RCCR 0 +#define CFG_PSDMR 0x016EB452 +#define CFG_MPTPR 0x00001900 +#define CFG_PSRT 0x00000021 + +#define CFG_RESET_ADDRESS 0x04400000 + +#endif /* __CONFIG_H */ diff --git a/include/configs/PCIPPC2.h b/include/configs/PCIPPC2.h new file mode 100644 index 0000000..b48d0d7 --- /dev/null +++ b/include/configs/PCIPPC2.h @@ -0,0 +1,266 @@ +/* + * (C) Copyright 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * + * Configuration settings for the PCIPPC-2 board. + * + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_PCIPPC2 1 /* this is a PCIPPC2 board */ + +#define CONFIG_BOARD_PRE_INIT 1 +#define CONFIG_MISC_INIT_R 1 + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 9600 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passed to Linux in MHz */ + +#define CONFIG_PREBOOT "" +#define CONFIG_BOOTDELAY 5 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_BSP | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_DOC | \ + CFG_CMD_ELF | \ + CFG_CMD_PCI ) + +#define CONFIG_PCI 1 +#define CONFIG_PCI_PNP 1 /* PCI plug-and-play */ + +/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) + */ +#include + + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CFG_HUSH_PARSER 1 /* use "hush" command parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + +/* Print Buffer Size + */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) + +#define CFG_MAXARGS 64 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x00100000 /* Default load address */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFF00000 +#define CFG_FLASH_MAX_SIZE 0x00100000 +/* Maximum amount of RAM. + */ +#define CFG_MAX_RAM_SIZE 0x20000000 /* 512Mb */ + +#define CFG_RESET_ADDRESS 0xFFF00100 + +#define CFG_MONITOR_BASE TEXT_BASE + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +#if CFG_MONITOR_BASE >= CFG_SDRAM_BASE && \ + CFG_MONITOR_BASE < CFG_SDRAM_BASE + CFG_MAX_RAM_SIZE +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MEMTEST_START 0x00004000 /* memtest works on */ +#define CFG_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area + */ + +/* Size in bytes reserved for initial data + */ +#define CFG_GBL_DATA_SIZE 128 + +#define CFG_INIT_RAM_ADDR 0x40000000 +#define CFG_INIT_RAM_END 0x8000 +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_INIT_RAM_LOCK + +/* + * Temporary buffer for serial data until the real serial driver + * is initialised (memtest will destroy this buffer) + */ +#define CFG_SCONSOLE_ADDR CFG_INIT_RAM_ADDR +#define CFG_SCONSOLE_SIZE 0x0002000 + +/* SDRAM 0 - 256MB + */ +#define CFG_DBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_DBAT0U (CFG_SDRAM_BASE | \ + BATU_BL_256M | BATU_VS | BATU_VP) +/* SDRAM 1 - 256MB + */ +#define CFG_DBAT1L ((CFG_SDRAM_BASE + 0x10000000) | \ + BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_DBAT1U ((CFG_SDRAM_BASE + 0x10000000) | \ + BATU_BL_256M | BATU_VS | BATU_VP) + +/* Init RAM in the CPU DCache (no backing memory) + */ +#define CFG_DBAT2L (CFG_INIT_RAM_ADDR | \ + BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_DBAT2U (CFG_INIT_RAM_ADDR | \ + BATU_BL_128K | BATU_VS | BATU_VP) + +/* I/O and PCI memory at 0xf0000000 + */ +#define CFG_DBAT3L (0xf0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_DBAT3U (0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT0L CFG_DBAT0L +#define CFG_IBAT0U CFG_DBAT0U +#define CFG_IBAT1L CFG_DBAT1L +#define CFG_IBAT1U CFG_DBAT1U +#define CFG_IBAT2L CFG_DBAT2L +#define CFG_IBAT2U CFG_DBAT2U +#define CFG_IBAT3L CFG_DBAT3L +#define CFG_IBAT3U CFG_DBAT3U + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + * For the detail description refer to the PCIPPC2 user's manual. + */ +#define CFG_HZ 1000 +#define CFG_BUS_HZ 100000000 /* bus speed - 100 mhz */ +#define CFG_CPU_CLK 300000000 +#define CFG_BUS_CLK 100000000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */ +#define CFG_MAX_FLASH_SECT 16 /* Max number of sectors in one bank */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ + +/* + * Note: environment is not EMBEDDED in the U-Boot code. + * It's stored in flash separately. + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x70000) +#define CFG_ENV_SIZE 0x1000 /* Size of the Environment */ +#define CFG_ENV_SECT_SIZE 0x10000 /* Size of the Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * L2 cache + */ +#undef CFG_L2 +#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ + L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) +#define L2_ENABLE (L2_INIT | L2CR_L2E) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/*----------------------------------------------------------------------- + * Disk-On-Chip configuration + */ + +#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ + +#define CFG_DOC_SUPPORT_2000 +#undef CFG_DOC_SUPPORT_MILLENNIUM + +/*----------------------------------------------------------------------- + RTC m48t59 +*/ +#define CONFIG_RTC_MK48T59 + +#define CONFIG_WATCHDOG + +#define CONFIG_NET_MULTI /* Multi ethernet cards support */ + +#define CONFIG_EEPRO100 +#define CONFIG_TULIP + +#endif /* __CONFIG_H */ diff --git a/include/configs/PCIPPC6.h b/include/configs/PCIPPC6.h new file mode 100644 index 0000000..bf858ec --- /dev/null +++ b/include/configs/PCIPPC6.h @@ -0,0 +1,282 @@ +/* + * (C) Copyright 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * + * Configuration settings for the PCIPPC-6 board. + * + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_PCIPPC2 1 /* this is a PCIPPC2 board */ + +#define CONFIG_BOARD_PRE_INIT 1 +#define CONFIG_MISC_INIT_R 1 + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 9600 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passed to Linux in MHz */ + +#define CONFIG_PREBOOT "" +#define CONFIG_BOOTDELAY 5 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_BSP | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_DOC | \ + CFG_CMD_ELF | \ + CFG_CMD_PCI | \ + CFG_CMD_SCSI ) + + +#define CONFIG_PCI 1 +#define CONFIG_PCI_PNP 1 /* PCI plug-and-play */ + +/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) + */ +#include + + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CFG_HUSH_PARSER 1 /* use "hush" command parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + +/* Print Buffer Size + */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) + +#define CFG_MAXARGS 64 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x00100000 /* Default load address */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFF00000 +#define CFG_FLASH_MAX_SIZE 0x00100000 +/* Maximum amount of RAM. + */ +#define CFG_MAX_RAM_SIZE 0x20000000 /* 512Mb */ + +#define CFG_RESET_ADDRESS 0xFFF00100 + +#define CFG_MONITOR_BASE TEXT_BASE + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +#if CFG_MONITOR_BASE >= CFG_SDRAM_BASE && \ + CFG_MONITOR_BASE < CFG_SDRAM_BASE + CFG_MAX_RAM_SIZE +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MEMTEST_START 0x00004000 /* memtest works on */ +#define CFG_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area + */ + +/* Size in bytes reserved for initial data + */ +#define CFG_GBL_DATA_SIZE 128 + +#define CFG_INIT_RAM_ADDR 0x40000000 +#define CFG_INIT_RAM_END 0x8000 +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_INIT_RAM_LOCK + +/* + * Temporary buffer for serial data until the real serial driver + * is initialised (memtest will destroy this buffer) + */ +#define CFG_SCONSOLE_ADDR CFG_INIT_RAM_ADDR +#define CFG_SCONSOLE_SIZE 0x0002000 + +/* SDRAM 0 - 256MB + */ +#define CFG_DBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_DBAT0U (CFG_SDRAM_BASE | \ + BATU_BL_256M | BATU_VS | BATU_VP) +/* SDRAM 1 - 256MB + */ +#define CFG_DBAT1L ((CFG_SDRAM_BASE + 0x10000000) | \ + BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_DBAT1U ((CFG_SDRAM_BASE + 0x10000000) | \ + BATU_BL_256M | BATU_VS | BATU_VP) + +/* Init RAM in the CPU DCache (no backing memory) + */ +#define CFG_DBAT2L (CFG_INIT_RAM_ADDR | \ + BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_DBAT2U (CFG_INIT_RAM_ADDR | \ + BATU_BL_128K | BATU_VS | BATU_VP) + +/* I/O and PCI memory at 0xf0000000 + */ +#define CFG_DBAT3L (0xf0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_DBAT3U (0xf0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT0L CFG_DBAT0L +#define CFG_IBAT0U CFG_DBAT0U +#define CFG_IBAT1L CFG_DBAT1L +#define CFG_IBAT1U CFG_DBAT1U +#define CFG_IBAT2L CFG_DBAT2L +#define CFG_IBAT2U CFG_DBAT2U +#define CFG_IBAT3L CFG_DBAT3L +#define CFG_IBAT3U CFG_DBAT3U + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + * For the detail description refer to the PCIPPC2 user's manual. + */ +#define CFG_HZ 1000 +#define CFG_BUS_HZ 100000000 /* bus speed - 100 mhz */ +#define CFG_CPU_CLK 300000000 +#define CFG_BUS_CLK 100000000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */ +#define CFG_MAX_FLASH_SECT 16 /* Max number of sectors in one bank */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ + +/* + * Note: environment is not EMBEDDED in the U-Boot code. + * It's stored in flash separately. + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x70000) +#define CFG_ENV_SIZE 0x1000 /* Size of the Environment */ +#define CFG_ENV_SECT_SIZE 0x10000 /* Size of the Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * L2 cache + */ +#undef CFG_L2 +#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ + L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) +#define L2_ENABLE (L2_INIT | L2CR_L2E) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/*----------------------------------------------------------------------- + * Disk-On-Chip configuration + */ + +#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ + +#define CFG_DOC_SUPPORT_2000 +#undef CFG_DOC_SUPPORT_MILLENNIUM + +/*----------------------------------------------------------------------- + RTC m48t59 +*/ +#define CONFIG_RTC_MK48T59 + +#define CONFIG_WATCHDOG + +#define CONFIG_NET_MULTI /* Multi ethernet cards support */ + +#define CONFIG_EEPRO100 +#define CONFIG_TULIP + + +#define CONFIG_SCSI_SYM53C8XX +#define CONFIG_SCSI_DEV_ID 0x000B /* 53c896 */ +#define CFG_SCSI_MAX_LUN 8 /* number of supported LUNs */ +#define CFG_SCSI_MAX_SCSI_ID 15 /* maximum SCSI ID (0..6) */ +#define CFG_SCSI_MAX_DEVICE CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN /* maximum Target devices */ +#define CFG_SCSI_SPIN_UP_TIME 2 +#define CFG_SCSI_SCAN_BUS_REVERSE 0 +#define CONFIG_DOS_PARTITION +#define CONFIG_MAC_PARTITION +#define CONFIG_ISO_PARTITION + + + +#endif /* __CONFIG_H */ diff --git a/include/configs/RRvision.h b/include/configs/RRvision.h new file mode 100644 index 0000000..ad36c95 --- /dev/null +++ b/include/configs/RRvision.h @@ -0,0 +1,467 @@ +/* + * (C) Copyright 2000, 2001, 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ +#define CONFIG_RRVISION 1 /* ...on a RRvision board */ + +#define CONFIG_8xx_GCLK_FREQ 64000000 + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "setenv stdout serial" + +#undef CONFIG_BOOTARGS +#define CONFIG_ETHADDR 00:50:C2:00:E0:70 +#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 +#define CONFIG_IPADDR 10.0.0.5 +#define CONFIG_SERVERIP 10.0.0.2 +#define CONFIG_NETMASK 255.0.0.0 +#define CONFIG_ROOTPATH /opt/eldk/ppc_8xx +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip)" \ + ":$(gatewayip):$(netmask):$(hostname):$(netdev):off\0" \ + "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ + "load=tftp 100000 /tftpboot/u-boot.bin\0" \ + "update=protect off 1:0-8;era 1:0-8;" \ + "cp.b 100000 40000000 $(filesize);" \ + "setenv filesize;saveenv\0" \ + "kernel_addr=40040000\0" \ + "ramdisk_addr=40100000\0" \ + "kernel_img=/tftpboot/pImage\0" \ + "kernel_load=tftp 200000 $(kernel_img)\0" \ + "net_nfs=run kernel_load nfsargs addip addtty;bootm\0" \ + "flash_nfs=run nfsargs addip addtty;bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" + + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#undef CONFIG_STATUS_LED /* disturbs display */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + + +#if 1 +#define CONFIG_VIDEO 1 /* To enable the video initialization */ + +/* Video related */ +#define CONFIG_VIDEO_LOGO 1 /* Show the logo */ +#define CONFIG_VIDEO_ENCODER_AD7176 1 /* Enable this encoder */ +#define CONFIG_VIDEO_ENCODER_AD7176_ADDR 0x2A /* ALSB to ground */ +#endif + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C /* I2C bit-banged */ + +# define CFG_I2C_SPEED 50000 /* 50 kHz is supposed to work */ +# define CFG_I2C_SLAVE 0xFE + +#ifdef CONFIG_SOFT_I2C +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(1) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ + + + +#define CONFIG_COMMANDS ( ( CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_I2C | \ + CFG_CMD_IDE | \ + CFG_CMD_DATE ) & \ + ~( CFG_CMD_PCMCIA | \ + CFG_CMD_IDE ) ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +/* timeout values are in ticks = ms */ +#define CFG_FLASH_ERASE_TOUT (120*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (1 * CFG_HZ) /* Timeout for Flash Write */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + */ + +/* for 64 MHz, we use a 16 MHz clock * 4 */ +#define CFG_PLPRCR ( (4-1)< ms + * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + * -------------------------------------------- + * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 + * + * 50 MHz => 50.000.000 / Divider = 98 + * 66 Mhz => 66.000.000 / Divider = 129 + * 80 Mhz => 80.000.000 / Divider = 156 + */ +#define CFG_MAMR_PTA 129 + +/* + * For 16 MBit, refresh rates could be 31.3 us + * (= 64 ms / 2K = 125 / quad bursts). + * For a simpler initialization, 15.6 us is used instead. + * + * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks + * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank + */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h new file mode 100644 index 0000000..1b867e0 --- /dev/null +++ b/include/configs/W7OLMC.h @@ -0,0 +1,326 @@ +/* + * (C) Copyright 2001 + * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ +#define CONFIG_4xx 1 /* ...member of PPC405 family */ +#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */ +#define CONFIG_W7OLMC 1 /* ...specifically an LMC */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#if 1 +#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */ +#else +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ +#endif + +#undef CONFIG_BOOTARGS + +#define CONFIG_LOADADDR F0080000 + +#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE +#define CONFIG_IPADDR 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_SERVERIP 192.168.1.2 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* disallow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ + +#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ + +#define CONFIG_COMMANDS \ + (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | CFG_CMD_BEDBUG | CFG_CMD_DATE | CFG_CMD_I2C | \ + CFG_CMD_EEPROM | CFG_CMD_ELF | CFG_CMD_BSP | CFG_CMD_REGINFO) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ + +#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ +#undef CFG_HUSH_PARSER /* No hush parse for U-Boot */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ +#define CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CFG_BASE_BAUD 384000 + + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE {9600} + +#define CFG_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* use extended board_info (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* pci plug-and-play */ +/* resource configuration */ +#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ +#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ +#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ + +/*----------------------------------------------------------------------- + * Set up values for external bus controller + * used by cpu_init.c + *----------------------------------------------------------------------- + */ + /* Don't use PerWE instead of PCI_INT ( these functions share a pin ) */ +#undef CONFIG_USE_PERWE + +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CFG_TEMP_STACK_OCM 1 + +/* bank 0 is boot flash */ +/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_W7O_EBC_PB0AP 0x03050440 +/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ +#define CFG_W7O_EBC_PB0CR 0xFFE38000 + +/* bank 1 is main flash */ +/* BME=0,TWT=11,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_EBC_PB1AP 0x05850240 +/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ +#define CFG_EBC_PB1CR 0xF00FC000 + +/* bank 2 is RTC/NVRAM */ +/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_EBC_PB2AP 0x03000440 +/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ +#define CFG_EBC_PB2CR 0xFC018000 + +/* bank 3 is FPGA 0 */ +/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ +#define CFG_EBC_PB3AP 0x02000400 +/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ +#define CFG_EBC_PB3CR 0xFD01A000 + +/* bank 4 is FPGA 1 */ +/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ +#define CFG_EBC_PB4AP 0x02000400 +/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ +#define CFG_EBC_PB4CR 0xFD11A000 + +/* bank 5 is FPGA 2 */ +/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ +#define CFG_EBC_PB5AP 0x02000400 +/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ +#define CFG_EBC_PB5CR 0xFD21A000 + +/* bank 6 is unused */ +/* pb6ap = 0 */ +#define CFG_EBC_PB6AP 0x00000000 +/* pb6cr = 0 */ +#define CFG_EBC_PB6CR 0x00000000 + +/* bank 7 is LED register */ +/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_W7O_EBC_PB7AP 0x03050440 +/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ +#define CFG_W7O_EBC_PB7CR 0xFE01C000 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFFC0000 +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ +#define CFG_FLASH_PROTECTION 1 /* Use real Flash protection */ + +#if 1 /* Use NVRAM for environment variables */ +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ +#define CFG_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ +#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */ +/*define CFG_ENV_ADDR \ + (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) Env */ +#define CFG_ENV_ADDR CFG_NVRAM_BASE_ADDR + +#else /* Use Boot Flash for environment variables */ +/*----------------------------------------------------------------------- + * Flash EEPROM for environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x10000 /* Total Size of env. sector */ + +#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */ +#endif + +/*----------------------------------------------------------------------- + * I2C EEPROM (CAT24WC08) for environment + */ +#define CONFIG_HARD_I2C /* I2c with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ + /* 16 byte page write mode using*/ + /* last 4 bits of the address */ +#define CFG_I2C_MULTI_EEPROMS +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above val. */ +#endif + +/* + * Init Memory Controller: + */ +#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ + +/* On Chip Memory location */ +#define CFG_OCM_DATA_ADDR 0xF8000000 +#define CFG_OCM_DATA_SIZE 0x1000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in RAM) + */ +#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */ +#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * FPGA(s) configuration + */ +#define CFG_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ +#define CONFIG_NUM_FPGAS 3 /* Number of FPGAs on board */ +#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ +#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ +#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */ + +#endif /* __CONFIG_H */ + diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h new file mode 100644 index 0000000..0c06e91 --- /dev/null +++ b/include/configs/W7OLMG.h @@ -0,0 +1,326 @@ +/* + * (C) Copyright 2001 + * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ +#define CONFIG_4xx 1 /* ...member of PPC405 family */ +#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */ +#define CONFIG_W7OLMG 1 /* ...specifically an LMG */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#if 1 +#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */ +#else +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ +#endif + +#undef CONFIG_BOOTARGS + +#define CONFIG_LOADADDR F0080000 + +#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE +#define CONFIG_IPADDR 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_SERVERIP 192.168.1.2 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* disallow baudrate change */ + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ + +#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +#define CONFIG_COMMANDS \ + (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | CFG_CMD_BEDBUG | CFG_CMD_DATE | CFG_CMD_I2C | \ + CFG_CMD_EEPROM | CFG_CMD_ELF | CFG_CMD_BSP | CFG_CMD_REGINFO | \ + CFG_CMD_DTT) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ + +#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ +#undef CFG_HUSH_PARSER /* No hush parse for U-Boot */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ +#define CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CFG_BASE_BAUD 384000 + + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE {9600} + +#define CFG_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* use extended board_info (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* pci plug-and-play */ +/* resource configuration */ +#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ +#define CFG_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ +#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ +#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ +#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ + +/*----------------------------------------------------------------------- + * Set up values for external bus controller + * used by cpu_init.c + *----------------------------------------------------------------------- + */ + /* use PerWE instead of PCI_INT ( these functions share a pin ) */ +#define CONFIG_USE_PERWE 1 + +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CFG_TEMP_STACK_OCM 1 + +/* bank 0 is boot flash */ +/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_W7O_EBC_PB0AP 0x03050440 +/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ +#define CFG_W7O_EBC_PB0CR 0xFFE38000 + +/* bank 1 is main flash */ +/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_EBC_PB1AP 0x04850240 +/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ +#define CFG_EBC_PB1CR 0xF00FC000 + +/* bank 2 is RTC/NVRAM */ +/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_EBC_PB2AP 0x03000440 +/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ +#define CFG_EBC_PB2CR 0xFC018000 + +/* bank 3 is FPGA 0 */ +/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ +#define CFG_EBC_PB3AP 0x02000400 +/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ +#define CFG_EBC_PB3CR 0xFD01A000 + +/* bank 4 is SAM 8 bit range */ +/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ +#define CFG_EBC_PB4AP 0x02840380 +/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ +#define CFG_EBC_PB4CR 0xFE878000 + +/* bank 5 is SAM 16 bit range */ +/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */ +#define CFG_EBC_PB5AP 0x05040d80 +/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ +#define CFG_EBC_PB5CR 0xFD87A000 + +/* bank 6 is unused */ +/* pb6ap = 0 */ +#define CFG_EBC_PB6AP 0x00000000 +/* pb6cr = 0 */ +#define CFG_EBC_PB6CR 0x00000000 + +/* bank 7 is LED register */ +/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CFG_W7O_EBC_PB7AP 0x03050440 +/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ +#define CFG_W7O_EBC_PB7CR 0xFE01C000 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFFC0000 +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ +#define CFG_FLASH_PROTECTION 1 /* Use real Flash protection */ + +#if 1 /* Use NVRAM for environment variables */ +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ +#define CFG_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ +#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */ +/*define CFG_ENV_ADDR \ + (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) Env */ +#define CFG_ENV_ADDR CFG_NVRAM_BASE_ADDR + +#else /* Use Boot Flash for environment variables */ +/*----------------------------------------------------------------------- + * Flash EEPROM for environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x10000 /* Total Size of env. sector */ + +#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */ +#endif + +/*----------------------------------------------------------------------- + * I2C EEPROM (ATMEL 24C04N) + */ +#define CONFIG_HARD_I2C 1 /* Hardware assisted I2C */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_I2C_MULTI_EEPROMS +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above val. */ +#endif + +/* + * Init Memory Controller: + */ +#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ + +/* On Chip Memory location */ +#define CFG_OCM_DATA_ADDR 0xF8000000 +#define CFG_OCM_DATA_SIZE 0x1000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in RAM) + */ +#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */ +#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * FPGA(s) configuration + */ +#define CFG_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ +#define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */ +#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ +#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ +#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h new file mode 100644 index 0000000..fc92d45 --- /dev/null +++ b/include/configs/lwmon.h @@ -0,0 +1,534 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC823 1 /* This is a MPC823E CPU */ +#define CONFIG_LWMON 1 /* ...on a LWMON board */ + +#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ + +#define CONFIG_LCD 1 /* use LCD controller ... */ +#define CONFIG_HLD1045 1 /* ... with a HLD1045 display */ + +#if 1 +#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */ +#else +#define CONFIG_8xx_CONS_SCC2 +#endif + +#define CONFIG_BAUDRATE 115200 /* with watchdog >= 38400 needed */ + +#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +/* pre-boot commands */ +#define CONFIG_PREBOOT "setenv bootdelay 15" + +#undef CONFIG_BOOTARGS + +/* POST support */ +#define CONFIG_POST (CFG_POST_CACHE | \ + CFG_POST_WATCHDOG | \ + CFG_POST_RTC | \ + CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_UART | \ + CFG_POST_ETHER | \ + CFG_POST_SPI | \ + CFG_POST_USB | \ + CFG_POST_SPR) + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kernel_addr=40040000\0" \ + "ramdisk_addr=40100000\0" \ + "magic_keys=#3\0" \ + "key_magic#=28\0" \ + "key_cmd#=setenv addfb setenv bootargs \\$(bootargs) console=tty0\0" \ + "key_magic3=24\0" \ + "key_cmd3=echo *** Entering Test Mode ***;" \ + "setenv add_misc setenv bootargs \\$(bootargs) testmode\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addfb=setenv bootargs $(bootargs) console=ttyS1,$(baudrate)\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off " \ + "panic=1\0" \ + "add_wdt=setenv bootargs $(bootargs) $(wdt_args)\0" \ + "flash_nfs=run nfsargs addip add_wdt addfb;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip add_wdt addfb;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 100000 /tftpboot/pImage.lwmon;" \ + "run nfsargs addip add_wdt addfb;bootm\0" \ + "rootpath=/opt/eldk/ppc_8xx\0" \ + "load=tftp 100000 /tftpboot/u-boot.bin\0" \ + "update=protect off 1:0;era 1:0;cp.b 100000 40000000 $(filesize)\0" \ + "wdt_args=wdt_8xx=off\0" \ + "verify=no" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#define CONFIG_WATCHDOG 1 /* watchdog enabled */ + +#undef CONFIG_STATUS_LED /* Status LED disabled */ + +/* enable I2C and select the hardware/software driver */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ + +#ifdef CONFIG_HARD_I2C +/* + * Hardware (CPM) I2C driver configuration + */ +# define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */ +# define CFG_I2C_SLAVE 0xFE +#endif /* CONFIG_HARD_I2C */ + +#ifdef CONFIG_SOFT_I2C +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(1) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ + + +#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */ + +#ifdef CONFIG_POST +#define CFG_CMD_POST_DIAG CFG_CMD_DIAG +#else +#define CFG_CMD_POST_DIAG 0 +#endif + +#ifdef CONFIG_8xx_CONS_SCC2 /* Can't use ethernet, then */ +#define CONFIG_COMMANDS ( (CONFIG_CMD_DFL & ~CFG_CMD_NET) | \ + CFG_CMD_DATE | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM | \ + CFG_CMD_IDE | \ + CFG_CMD_BSP | \ + CFG_CMD_POST_DIAG ) +#else +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_DATE | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM | \ + CFG_CMD_IDE | \ + CFG_CMD_BSP | \ + CFG_CMD_POST_DIAG ) +#endif +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/*----------------------------------------------------------------------*/ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#undef CFG_HUSH_PARSER /* enable "hush" shell */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ + +#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#if defined(DEBUG) || (CONFIG_COMMANDS & CFG_CMD_IDE) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */ + +#if 1 +/* Put environment in flash which is much faster to boot */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR 0x40040000 /* Address of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment */ +#define CFG_ENV_SECT_SIZE 0x40000 /* we have BIG sectors only :-( */ +#else +/* Environment in EEPROM */ +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 2048 +#endif +/*----------------------------------------------------------------------- + * I2C/EEPROM Configuration + */ + +#define CFG_I2C_AUDIO_ADDR 0x28 /* Audio volume control */ +#define CFG_I2C_SYSMON_ADDR 0x2E /* LM87 System Monitor */ +#define CFG_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */ +#define CFG_I2C_POWER_A_ADDR 0x52 /* PCMCIA/USB power switch, channel A */ +#define CFG_I2C_POWER_B_ADDR 0x53 /* PCMCIA/USB power switch, channel B */ +#define CFG_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ +#define CFG_I2C_PICIO_ADDR 0x57 /* PIC IO Expander */ + +#define CONFIG_USE_FRAM /* Use FRAM instead of EEPROM */ +#ifdef CONFIG_USE_FRAM /* use FRAM */ +#define CFG_I2C_EEPROM_ADDR 0x55 /* FRAM FM24CL64 */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#else /* use EEPROM */ +#define CFG_I2C_EEPROM_ADDR 0x58 /* EEPROM AT24C164 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ +#endif /* CONFIG_USE_FRAM */ +#define CFG_EEPROM_PAGE_WRITE_BITS 4 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if 0 && defined(CONFIG_WATCHDOG) /* LWMON uses external MAX706TESA WD */ +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +/* EARB, DBGC and DBPC are initialised by the HCW */ +/* => 0x000000C0 */ +#define CFG_SIUMCR (SIUMCR_GB5E) +/*#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit, set PLL multiplication factor ! + */ +/* 0x00405000 */ +#define CFG_PLPRCR_MF 4 /* (4+1) * 13.2 = 66 MHz Clock */ +#define CFG_PLPRCR \ + ( (CFG_PLPRCR_MF << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ + /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ + PLPRCR_CSR /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/ \ + ) + +#define CONFIG_8xx_GCLK_FREQ ((CFG_PLPRCR_MF+1)*13200000) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +/* 0x01800000 */ +#define CFG_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \ + SCCR_RTDIV | SCCR_RTSEL | \ + /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ + SCCR_EBDF00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000 | \ + SCCR_DFNH000 | SCCR_DFLCD100 | \ + SCCR_DFALCD01) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +/* 0x00C3 => 0x0003 */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration Register 19-4 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0x0000 + +/*----------------------------------------------------------------------- + * RMDS - RISC Microcode Development Support Control Register + *----------------------------------------------------------------------- + */ +#define CFG_RMDS 0 + +/*----------------------------------------------------------------------- + * + * Interrupt Levels + *----------------------------------------------------------------------- + */ +#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0x50000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0x54000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0x58000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0x5C000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) - second Flash bank optional + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x41000000 /* FLASH bank #1 */ + +/* used to re-map FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0xFF000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFF000000 /* OR addr mask */ + +/* FLASH timing: ACS = 00, TRLX = 0, CSNT = 1, SCY = 8, EHTR = 0 */ +#define CFG_OR_TIMING_FLASH (OR_SCY_8_CLK) + +#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ + CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \ + CFG_OR_TIMING_FLASH) +/* 16 bit, bank valid */ +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V ) + +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM CFG_OR0_PRELIM +#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V ) + +/* + * BR3/OR3: SDRAM + * + * Multiplexed addresses, GPL5 output to GPL5_A (don't care) + */ +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ +#define SDRAM_PRELIM_OR_AM 0xF0000000 /* map 256 MB (>SDRAM_MAX_SIZE!) */ +#define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */ + +#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB SDRAM */ + +#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING ) +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* + * BR5/OR5: Touch Panel + * + * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0 + */ +#define TOUCHPNL_BASE 0x20000000 +#define TOUCHPNL_OR_AM 0xFFFF8000 +#define TOUCHPNL_TIMING OR_SCY_0_CLK + +#define CFG_OR5_PRELIM (TOUCHPNL_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ + TOUCHPNL_TIMING ) +#define CFG_BR5_PRELIM ((TOUCHPNL_BASE & BR_BA_MSK) | BR_PS_32 | BR_V ) + +#define CFG_MEMORY_75 +#undef CFG_MEMORY_7E +#undef CFG_MEMORY_8E + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CFG_MPTPR 0x200 + +/* + * MAMR settings for SDRAM + */ + +#define CFG_MAMR_8COL 0x80802114 +#define CFG_MAMR_9COL 0x80904114 + +/* + * MAR setting for SDRAM + */ +#define CFG_MAR 0x00000088 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h new file mode 100644 index 0000000..95faa41 --- /dev/null +++ b/include/configs/rsdproto.h @@ -0,0 +1,415 @@ +/* + * (C) Copyright 2000 + * Murray Jensen + * + * (C) Copyright 2000 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * Configuation settings for the R&S Protocol Board board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_RSD_PROTO 1 /* on a R&S Protocol Board */ + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere. + */ +#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on neither */ +#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CFG_CMD_NET must be removed + * from CONFIG_COMMANDS to remove support for networking. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ +#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ +#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ + +#if (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) +# define CFG_CPMFCR_RAMTYPE (0) +# define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_INDEX */ + + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* enable I2C */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 50000000 /* in Hz */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_KGDB) + +/* Define this if you want to boot from 0x00000100. If you don't define + * this, you will need to program the bootloader to 0xfff00000, and + * get the hardware reset config words at 0xfe000000. The simplest + * way to do that is to program the bootloader at both addresses. + * It is suggested that you just let U-Boot live at 0x00000000. + */ +#define CFG_RSD_BOOT_LOW 1 + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#define CONFIG_BOOTDELAY 5 +#define CONFIG_BOOTARGS "devfs=mount root=ramfs" +#define CONFIG_ETHADDR 08:00:3e:26:0a:5a +#define CONFIG_NETMASK 255.255.0.0 + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + + /* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define PHYS_SDRAM_60X 0x00000000 /* SDRAM (60x Bus) */ +#define PHYS_SDRAM_60X_SIZE 0x08000000 /* 128 MB */ + +#define PHYS_SDRAM_LOCAL 0x40000000 /* SDRAM (Local Bus) */ +#define PHYS_SDRAM_LOCAL_SIZE 0x04000000 /* 64 MB */ + +#define PHYS_DPRAM_PCI 0xE8000000 /* DPRAM PPC/PCI */ +#define PHYS_DPRAM_PCI_SIZE 0x00020000 /* 128 KB */ + +/*#define PHYS_DPRAM_PCI_SEM 0x04020000 / * DPRAM PPC/PCI Semaphore */ +/*#define PHYS_DPRAM_PCI_SEM_SIZE 0x00000001 / * 1 Byte */ + +#define PHYS_DPRAM_SHARC 0xE8100000 /* DPRAM PPC/Sharc */ +#define PHYS_DPRAM_SHARC_SIZE 0x00040000 /* 256 KB */ + +/*#define PHYS_DPRAM_SHARC_SEM 0x04140000 / * DPRAM PPC/Sharc Semaphore */ +/*#define PHYS_DPRAM_SHARC_SEM_SIZE 0x00000001 / * 1 Byte */ + +#define PHYS_VIRTEX_REGISTER 0xE8300000 /* FPGA implemented register */ +#define PHYS_VIRTEX_REGISTER_SIZE 0x00000100 + +#define PHYS_USB 0x04200000 /* USB Controller (60x Bus) */ +#define PHYS_USB_SIZE 0x00000002 /* 2 Bytes */ + +#define PHYS_IMMR 0xF0000000 /* Internal Memory Mapped Reg. */ + +#define PHYS_FLASH 0xFF000000 /* Flash (60x Bus) */ +#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ + +#define CFG_IMMR PHYS_IMMR + +/*----------------------------------------------------------------------- + * Reset Address + * + * In order to reset the CPU, U-Boot jumps to a special address which + * causes a machine check exception. The default address for this is + * CFG_MONITOR_BASE - sizeof (ulong), which might not always work, eg. when + * testing the monitor in RAM using a JTAG debugger. + * + * Just set CFG_RESET_ADDRESS to an address that you know is sure to + * cause a bus error on your hardware. + */ +#define CFG_RESET_ADDRESS 0x20000000 + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + */ + +#if defined(CFG_RSD_BOOT_LOW) +# define CFG_RSD_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) +#else +# define CFG_RSD_HRCW_BOOT_FLAGS (0) +#endif /* defined(CFG_RSD_BOOT_LOW) */ + +/* get the HRCW ISB field from CFG_IMMR */ +#define CFG_RSD_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) |\ + ((CFG_IMMR & 0x01000000) >> 7) |\ + ((CFG_IMMR & 0x00100000) >> 4) ) + +#define CFG_HRCW_MASTER (HRCW_L2CPC10 | \ + HRCW_DPPC11 | \ + CFG_RSD_HRCW_IMMR |\ + HRCW_MMR00 | \ + HRCW_APPC10 | \ + HRCW_CS10PC00 | \ + HRCW_MODCK_H0000 |\ + CFG_RSD_HRCW_BOOT_FLAGS) + +/* no slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Note also that the logic that sets CFG_RAMBOOT is platform dependend. + */ +#define CFG_SDRAM_BASE PHYS_SDRAM_60X +#define CFG_FLASH_BASE PHYS_FLASH +/*#define CFG_MONITOR_BASE 0x200000 */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#if CFG_MONITOR_BASE < CFG_FLASH_BASE +#define CFG_RAMBOOT +#endif +#define CFG_MONITOR_LEN (160 << 10) /* Reserve 160 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 63 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 12000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 3000 /* Timeout for Flash Write (in ms) */ + +/* turn off NVRAM env feature */ +#undef CONFIG_NVRAM_ENV + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (PHYS_FLASH + 0x28000) /* Addr of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x8000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE) +#define CFG_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE|HID0_EMCP) +#define CFG_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register + *----------------------------------------------------------------------- + */ +#define CFG_RMR 0 + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CFG_BCR 0x100c0000 + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ + +#define CFG_SIUMCR (SIUMCR_DPPC11 | SIUMCR_L2CPC10 | SIUMCR_APPC10 | \ + SIUMCR_CS10PC01 | SIUMCR_BCTLC01) + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_PBME | SYPCR_LBME | \ + SYPCR_SWRI | SYPCR_SWP) + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC | TMCNTSC_ALR | TMCNTSC_TCF | TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + */ +#define CFG_SCCR 0x00000000 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + */ + +#define CFG_PSDMR 0x494D2452 +#define CFG_LSDMR 0x49492552 + +/* Flash */ +#define CFG_BR0_PRELIM (PHYS_FLASH | BRx_V) +#define CFG_OR0_PRELIM (P2SZ_TO_AM(PHYS_FLASH_SIZE) | \ + ORxG_BCTLD | \ + ORxG_SCY_5_CLK) + +/* DPRAM to the PCI BUS on the protocol board */ +#define CFG_BR1_PRELIM (PHYS_DPRAM_PCI | BRx_V) +#define CFG_OR1_PRELIM (P2SZ_TO_AM(PHYS_DPRAM_PCI_SIZE) | \ + ORxG_ACS_DIV4) + +/* 60x Bus SDRAM */ +#define CFG_BR2_PRELIM (PHYS_SDRAM_60X | BRx_MS_SDRAM_P | BRx_V) +#define CFG_OR2_PRELIM (ORxS_SIZE_TO_AM(PHYS_SDRAM_60X_SIZE) | \ + ORxS_BPD_4 | \ + ORxS_ROWST_PBI1_A2 | \ + ORxS_NUMR_13 | \ + ORxS_IBID) + +/* Virtex-FPGA - Register */ +#define CFG_BR3_PRELIM (PHYS_VIRTEX_REGISTER | BRx_V) +#define CFG_OR3_PRELIM (ORxS_SIZE_TO_AM(PHYS_VIRTEX_REGISTER_SIZE) | \ + ORxG_SCY_1_CLK | \ + ORxG_ACS_DIV2 | \ + ORxG_CSNT ) + +/* local bus SDRAM */ +#define CFG_BR4_PRELIM (PHYS_SDRAM_LOCAL | BRx_PS_32 | BRx_MS_SDRAM_L | BRx_V) +#define CFG_OR4_PRELIM (ORxS_SIZE_TO_AM(PHYS_SDRAM_LOCAL_SIZE) | \ + ORxS_BPD_4 | \ + ORxS_ROWST_PBI1_A4 | \ + ORxS_NUMR_13) + +/* DPRAM to the Sharc-Bus on the protocol board */ +#define CFG_BR5_PRELIM (PHYS_DPRAM_SHARC | BRx_V) +#define CFG_OR5_PRELIM (P2SZ_TO_AM(PHYS_DPRAM_SHARC_SIZE) | \ + ORxG_ACS_DIV4) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h new file mode 100644 index 0000000..a3a7ec3 --- /dev/null +++ b/include/linux/mtd/nand.h @@ -0,0 +1,87 @@ +/* + * u-boot/include/linux/mtd/nand.h + * + * Copyright (c) 2000 David Woodhouse + * Steven J. Hill + * + * $Id: nand.h,v 1.8 2000/10/30 17:16:17 sjhill Exp $ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Info: + * Contains standard defines and IDs for NAND flash devices + * + * Changelog: + * 01-31-2000 DMW Created + * 09-18-2000 SJH Moved structure out of the Disk-On-Chip drivers + * so it can be used by other NAND flash device + * drivers. I also changed the copyright since none + * of the original contents of this file are specific + * to DoC devices. David can whack me with a baseball + * bat later if I did something naughty. + * 10-11-2000 SJH Added private NAND flash structure for driver + * 10-24-2000 SJH Added prototype for 'nand_scan' function + */ +#ifndef __LINUX_MTD_NAND_H +#define __LINUX_MTD_NAND_H + +/* + * Standard NAND flash commands + */ +#define NAND_CMD_READ0 0 +#define NAND_CMD_READ1 1 +#define NAND_CMD_PAGEPROG 0x10 +#define NAND_CMD_READOOB 0x50 +#define NAND_CMD_ERASE1 0x60 +#define NAND_CMD_STATUS 0x70 +#define NAND_CMD_SEQIN 0x80 +#define NAND_CMD_READID 0x90 +#define NAND_CMD_ERASE2 0xd0 +#define NAND_CMD_RESET 0xff + +/* + * NAND Flash Manufacturer ID Codes + */ +#define NAND_MFR_TOSHIBA 0x98 +#define NAND_MFR_SAMSUNG 0xec + +/* + * NAND Flash Device ID Structure + * + * Structure overview: + * + * name - Complete name of device + * + * manufacture_id - manufacturer ID code of device. + * + * model_id - model ID code of device. + * + * chipshift - total number of address bits for the device which + * is used to calculate address offsets and the total + * number of bytes the device is capable of. + * + * page256 - denotes if flash device has 256 byte pages or not. + * + * pageadrlen - number of bytes minus one needed to hold the + * complete address into the flash array. Keep in + * mind that when a read or write is done to a + * specific address, the address is input serially + * 8 bits at a time. This structure member is used + * by the read/write routines as a loop index for + * shifting the address out 8 bits at a time. + * + * erasesize - size of an erase block in the flash device. + */ +struct nand_flash_dev { + char * name; + int manufacture_id; + int model_id; + int chipshift; + char page256; + char pageadrlen; + unsigned long erasesize; +}; + +#endif /* __LINUX_MTD_NAND_H */ diff --git a/include/linux/mtd/nand_ids.h b/include/linux/mtd/nand_ids.h new file mode 100644 index 0000000..6b733be --- /dev/null +++ b/include/linux/mtd/nand_ids.h @@ -0,0 +1,52 @@ +/* + * u-boot/include/linux/mtd/nand_ids.h + * + * Copyright (c) 2000 David Woodhouse + * Steven J. Hill + * + * $Id: nand_ids.h,v 1.1 2000/10/13 16:16:26 mdeans Exp $ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Info: + * Contains standard defines and IDs for NAND flash devices + * + * Changelog: + * 01-31-2000 DMW Created + * 09-18-2000 SJH Moved structure out of the Disk-On-Chip drivers + * so it can be used by other NAND flash device + * drivers. I also changed the copyright since none + * of the original contents of this file are specific + * to DoC devices. David can whack me with a baseball + * bat later if I did something naughty. + * 10-11-2000 SJH Added private NAND flash structure for driver + * 2000-10-13 BE Moved out of 'nand.h' - avoids duplication. + */ + +#ifndef __LINUX_MTD_NAND_IDS_H +#define __LINUX_MTD_NAND_IDS_H + +static struct nand_flash_dev nand_flash_ids[] = { + {"Toshiba TC5816BDC", NAND_MFR_TOSHIBA, 0x64, 21, 1, 2, 0x1000}, + {"Toshiba TC5832DC", NAND_MFR_TOSHIBA, 0x6b, 22, 0, 2, 0x2000}, + {"Toshiba TH58V128DC", NAND_MFR_TOSHIBA, 0x73, 24, 0, 2, 0x4000}, + {"Toshiba TC58256FT/DC", NAND_MFR_TOSHIBA, 0x75, 25, 0, 2, 0x4000}, + {"Toshiba TH58512FT", NAND_MFR_TOSHIBA, 0x76, 26, 0, 3, 0x4000}, + {"Toshiba TC58V32DC", NAND_MFR_TOSHIBA, 0xe5, 22, 0, 2, 0x2000}, + {"Toshiba TC58V64AFT/DC", NAND_MFR_TOSHIBA, 0xe6, 23, 0, 2, 0x2000}, + {"Toshiba TC58V16BDC", NAND_MFR_TOSHIBA, 0xea, 21, 1, 2, 0x1000}, + {"Samsung KM29N16000", NAND_MFR_SAMSUNG, 0x64, 21, 1, 2, 0x1000}, + {"Samsung unknown 4Mb", NAND_MFR_SAMSUNG, 0x6b, 22, 0, 2, 0x2000}, + {"Samsung KM29U128T", NAND_MFR_SAMSUNG, 0x73, 24, 0, 2, 0x4000}, + {"Samsung KM29U256T", NAND_MFR_SAMSUNG, 0x75, 25, 0, 2, 0x4000}, + {"Samsung unknown 64Mb", NAND_MFR_SAMSUNG, 0x76, 26, 0, 3, 0x4000}, + {"Samsung KM29W32000", NAND_MFR_SAMSUNG, 0xe3, 22, 0, 2, 0x2000}, + {"Samsung unknown 4Mb", NAND_MFR_SAMSUNG, 0xe5, 22, 0, 2, 0x2000}, + {"Samsung KM29U64000", NAND_MFR_SAMSUNG, 0xe6, 23, 0, 2, 0x2000}, + {"Samsung KM29W16000", NAND_MFR_SAMSUNG, 0xea, 21, 1, 2, 0x1000}, + {NULL,} +}; + +#endif /* __LINUX_MTD_NAND_IDS_H */ -- cgit v0.10.2