Motorola MPC8540ADS and MPC8560ADS board Xianghua Xiao(X.Xiao@motorola.com) Created 10/15/03 ----------------------------------------- 0. Toolchain The Binutils in current ELDK toolchain will not support MPC85xx chip. You need use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils. 1. SWITCH SETTINGS & JUMPERS 1.1 First, make sure the board default setting is consistent with the document shipped with your board. Then apply the following changes: SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used) SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560) SW11[2]='OFF for dracom, ON for draco' (single switch to toggle draco.dracom mode) SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector) SW22[1-4]="OFF OFF ON OFF" SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF" J1 = "Enable Prog" (Make sure your flash is programmable for development) Ethernet PHY connectors(J47,J56) should be removed if you want to use the ethernet. 1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will have to change the system clock from the default 66Mhz to 33Mhz by setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need double your platform clock(SW6) because the system clock is now only half of its original value. 1.3 SW6 is a very important switch, it decides your platform clock and CPU clock based on the on-board system clock(default 66MHz). Check the document along with your board for details. 2. MEMORY MAP TO WORK WITH LINUX KERNEL 2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and linux kernel, you can customize it based on your system requirements: DDR: 0x00000000-0x1fffffff (max 512MB) PCI: 0xe0000000-0xefffffff (256MB) RIO: 0xf0000000-0xf7ffffff (128MB) Local SDRAM: 0xf8000000-0xfbffffff (64MB) Local CSx: 0xfc000000-0xfdefffff (31MB) BCSR,RTC,ATM config,etc. CCSRBAR: 0xfdf00000-0xfdffffff (1MB) Flash: 0xfe000000-0xffffffff (max 32MB) 2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. Hope you will be able to download them from linuxppc-2.4 public source by the time you are reading this. Please make sure the kernel's ppcboot.h is consistent with U-Boot's u-boot.h, then you can use two default configuration files in the kernel source as a test: arch/ppc/configs/mpc8540ads_defconfig arch/ppc/configs/mpc8560ads_defconfig 3. DEFINITIONS AND COMPILATION 3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/ configs/MPC8560ADS.h CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, IBM 440, etc) CONFIG_E500 BOOKE e500 family(Motorola) CONFIG_MPC85xx MPC8540,MPC8560 and their derivatives CONFIG_MPC85xx_REV1 MPC85xx Rev 1 Chip, in general you will use a Rev2 chip from Nov.2003. If you still see this definition while you have a Rev2(and newer) chip,undef this. CONFIG_MPC8540 MPC8540 specific CONFIG_MPC8560 MPC8560 specific CONFIG_MPC8540ADS MPC8540ADS board specific CONFIG_MPC8560ADS MPC8560ADS board specific CONFIG_TSEC_ENET Use on-chip 10/100/1000 ethernet for networking CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can also manual config the DDR after undef this definition. CONFIG_DDR_ECC only for ECC DDR module CONFIG_DDR_DLL possible DLL fix needed for Rev1 chip for more stability. you can disable this if you're having a newer chip. CONFIG_RAM_AS_FLASH after define this, you can load U-Boot into localbus SDRAM and treat localbus SDRAM as a flash. We use this memory based U-Boot before flash is working while Metrowerks and Windriver are still working on their flash/JTAG tools. if you can program the flash directly, undef this. Other than the above definitions, the rest in the config files are straightforward. 3.2 Compilation export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell) cd u-boot make distclean make MPC8560ADS_config (or make MPC8540ADS_config) make 4. Note on the 10/100/1000 Ethernet controller: 4.1 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that happens, you can try the following steps to make network work: MPC8560ADS>tftp 1000000 pImage (if it hangs, use Ctrl-C to quit) MPC8560ADS>nm fdf24524 >0 >1 >. (to quit this memory operation) MPC8560ADS>tftp 1000000 pImage 5. Screen dump: 5.1 MPC8540ADS board U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33) Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010 Board: Motorola MPC8540ADS Board CPU: 792 MHz CCB: 264 MHz DDR: 132 MHz LBC: 66 MHz L1 D-cache 32KB, L1 I-cache 32KB enabled. I2C: ready DRAM: DDR module detected, total size:128MB. 128 MB FLASH: 16 MB L2 cache enabled: 256KB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: MOTOROLA ETHERNE Hit any key to stop autoboot: 0 MPC8540ADS=> fli Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K) Size: 16 MB in 64 Sectors Sector Start Addresses: FF000000 FF040000 FF080000 FF0C0000 FF100000 FF140000 FF180000 FF1C0000 FF200000 FF240000 FF280000 FF2C0000 FF300000 FF340000 FF380000 FF3C0000 FF400000 FF440000 FF480000 FF4C0000 FF500000 FF540000 FF580000 FF5C0000 FF600000 FF640000 FF680000 FF6C0000 FF700000 FF740000 FF780000 FF7C0000 FF800000 FF840000 FF880000 FF8C0000 FF900000 FF940000 FF980000 FF9C0000 FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000 FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000 FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000 FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000 FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO) MPC8540ADS=> imi ff000000 ## Checking Image at ff000000 ... Image Name: Linux-2.4.21-rc5 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 800594 Bytes = 781.8 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK MPC8540ADS=> bdinfo memstart = 0x00000000 memsize = 0x08000000 flashstart = 0xFF000000 flashsize = 0x01000000 flashoffset = 0x00000000 sramstart = 0x00000000 sramsize = 0x00000000 immr_base = 0xFDF00000 bootflags = 0x40003F80 intfreq = 792 MHz busfreq = 264 MHz ethaddr = 00:01:AF:07:9B:8A eth1addr = 00:01:AF:07:9B:8B eth2addr = 00:01:AF:07:9B:8C IP addr = 10.82.0.105 baudrate = 115200 bps MPC8540ADS=> printenv bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200 bootcmd=bootm 0xff300000 0xff700000 bootdelay=3 baudrate=115200 loads_echo=1 ethaddr=00:01:af:07:9b:8a eth1addr=00:01:af:07:9b:8b eth2addr=00:01:af:07:9b:8c ipaddr=10.82.0.105 serverip=163.12.64.52 rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx gatewayip=10.82.1.254 netmask=255.255.254.0 hostname=MPC8560ADS_PILOT_003 bootfile=pImage stdin=serial stdout=serial stderr=serial Environment size: 560/8188 bytes MPC8540ADS=> bootm ff000000 ## Booting image at ff000000 ... Image Name: Linux-2.4.21-rc5 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 800594 Bytes = 781.8 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK mpc85xx_init(): exit id mach(): done MMU:enter Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb MMU:hw init MMU:mapin MMU:mapin_ram done MMU:setio MMU:exit Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #1 Wed Oct 15 09:05:42 CDT 2003 setup_arch: enter setup_arch: bootmem mpc85xx_setup_arch Host Bridge Vendor ID = 1057 Host Bridge Device ID = 3 Host Bridge header = 0 arch: exit On node 0 totalpages: 32768 zone(0): 32768 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200 openpic: enter OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000 openpic: timer openpic: external openpic: spurious openpic: exit time_init: decrementer frequency = 33.000000 MHz Calibrating delay loop... 226.09 BogoMIPS Memory: 127488k available (1344k kernel code, 448k data, 248k init, 0k highmem) Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) Inode cache hash table entries: 8192 (order: 4, 65536 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Installing knfsd (copyright (C) 1996 okir@monad.swb.de). pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0xfdf04500 (irq = 90) is a 16550A ttyS01 at 0xfdf04600 (irq = 0) is a 16550A eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a: eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b: RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 5.0.43-k1 Copyright (c) 1999-2003 Intel Corporation. PPP generic driver version 2.4.2 PPP Deflate Compression module registered NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 1024 buckets, 8Kbytes TCP: Hash tables configured (established 8192 bind 8192) IP-Config: Complete: device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254, host=mpc8540ads-003, domain=, nis-domain=(none), bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath= NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 163.12.64.52 Looking up port of RPC 100005/1 on 163.12.64.52 VFS: Mounted root (nfs filesystem). Freeing unused kernel memory: 248k init INIT: version 2.78 booting Activating swap... Checking all file systems... Parallelizing fsck version 1.22 (22-Jun-2001) Mounting local filesystems... nothing was mounted Cleaning: /etc/network/ifstate. Setting up IP spoofing protection: rp_filter. Disable TCP/IP Explicit Congestion Notification: done. Configuring network interfaces: done. Starting portmap daemon: portmap. Cleaning: /tmp /var/lock /var/run. INIT: Entering runlevel: 2 Starting system log daemon: syslogd klogd. Starting internet superserver: inetd. mpc8540ads-003 login: root Last login: Thu Jan 1 00:00:07 1970 on console Linux mpc8540ads-003 2.4.21-rc5 #1 Wed Oct 15 09:05:42 CDT 2003 ppc unknown root@mpc8540ads-003:~# ls 21142.o aa e100.o hello.o mii.o timer.o root@mpc8540ads-003:~# /sbin/ifconfig eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4576 errors:0 dropped:0 overruns:0 frame:0 TX packets:2587 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:4457023 (4.2 Mb) TX bytes:437770 (427.5 Kb) Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:296 (296.0 b) TX bytes:296 (296.0 b) root@mpc8540ads-003:~# ping 163.12.64.52 PING 163.12.64.52 (163.12.64.52): 56 data bytes 64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.2 ms 64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms 64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms --- 163.12.64.52 ping statistics --- 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 0.1/0.1/0.2 ms root@mpc8540ads-003:~# 5.2 MPC8560ADS board U-Boot 1.0.0-pre (Oct 15 2003 - 13:42:04) Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010 Board: Motorola MPC8560ADS Board CPU: 792 MHz CCB: 264 MHz DDR: 132 MHz LBC: 66 MHz CPM: 264 Mhz L1 D-cache 32KB, L1 I-cache 32KB enabled. I2C: ready DRAM: DDR module detected, total size:128MB. 128 MB FLASH: 16 MB L2 cache enabled: 256KB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: MOTOROLA ETHERNE Hit any key to stop autoboot: 3 MPC8560ADS=> bdinfo memstart = 0x00000000 memsize = 0x08000000 flashstart = 0xFF000000 flashsize = 0x01000000 flashoffset = 0x00000000 sramstart = 0x00000000 sramsize = 0x00000000 immr_base = 0xFDF00000 bootflags = 0x00000000 vco = 528 MHz sccfreq = 132 MHz brgfreq = 132 MHz intfreq = 792 MHz cpmfreq = 264 MHz busfreq = 264 MHz ethaddr = 00:01:AF:07:9B:8A eth1addr = 00:01:AF:07:9B:8B eth2addr = 00:01:AF:07:9B:8C IP addr = 10.82.0.105 baudrate = 115200 bps MPC8560ADS=> printenv bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200 bootcmd=bootm 0xff400000 0xff700000 bootdelay=3 baudrate=115200 loads_echo=1 ethaddr=00:01:af:07:9b:8a eth1addr=00:01:af:07:9b:8b eth2addr=00:01:af:07:9b:8c ipaddr=10.82.0.105 serverip=163.12.64.52 rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx gatewayip=10.82.1.254 netmask=255.255.254.0 hostname=MPC8560ADS_PILOT_003 bootfile=pImage stdin=serial stdout=serial stderr=serial Environment size: 560/8188 bytes MPC8560ADS=> fli Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K) Size: 16 MB in 64 Sectors Sector Start Addresses: FF000000 FF040000 FF080000 FF0C0000 FF100000 FF140000 FF180000 FF1C0000 FF200000 FF240000 FF280000 FF2C0000 FF300000 FF340000 FF380000 FF3C0000 FF400000 FF440000 FF480000 FF4C0000 FF500000 FF540000 FF580000 FF5C0000 FF600000 FF640000 FF680000 FF6C0000 FF700000 FF740000 FF780000 FF7C0000 FF800000 FF840000 FF880000 FF8C0000 FF900000 FF940000 FF980000 FF9C0000 FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000 FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000 FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000 FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000 FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO) MPC8560ADS=> imi ff100000 ## Checking Image at ff100000 ... Image Name: Linux-2.4.21-rc5 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 755361 Bytes = 737.7 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK MPC8560ADS=> tftp 1000000 pImage.dracom.public TFTP from server 163.12.64.52; our IP address is 10.82.0.105; sending through gateway 10.82.1.254 Filename 'pImage.dracom.public'. Load address: 0x1000000 Loading: *################################################################# ################################################################# ################## done Bytes transferred = 755425 (b86e1 hex) MPC8560ADS=> bootm ff100000 ## Booting image at ff100000 ... Image Name: Linux-2.4.21-rc5 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 755361 Bytes = 737.7 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK mpc85xx_init(): exit id mach(): done MMU:enter Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb MMU:hw init MMU:mapin MMU:mapin_ram done MMU:setio MMU:exit Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #2 Wed Oct 15 09:13:46 CDT 2003 setup_arch: enter setup_arch: bootmem mpc85xx_setup_arch Host Bridge Vendor ID = 1057 Host Bridge Device ID = 3 Host Bridge header = 0 arch: exit On node 0 totalpages: 32768 zone(0): 32768 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200 openpic: enter OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000 openpic: timer openpic: external openpic: spurious openpic: exit time_init: decrementer frequency = 33.000000 MHz Calibrating delay loop... 226.09 BogoMIPS Memory: 127624k available (1276k kernel code, 384k data, 236k init, 0k highmem) Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) Inode cache hash table entries: 8192 (order: 4, 65536 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Installing knfsd (copyright (C) 1996 okir@monad.swb.de). CPM UART driver version 0.01 ttyS0 on SCC1 at 0x8000, BRG1 UART interrupt installed(40) pty: 256 Unix98 ptys configured eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a: eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b: RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 5.0.43-k1 Copyright (c) 1999-2003 Intel Corporation. PPP generic driver version 2.4.2 PPP Deflate Compression module registered NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 1024 buckets, 8Kbytes TCP: Hash tables configured (established 8192 bind 8192) IP-Config: Complete: device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254, host=mpc8560ads-003, domain=, nis-domain=(none), bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath= NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 163.12.64.52 Looking up port of RPC 100005/1 on 163.12.64.52 VFS: Mounted root (nfs filesystem). Freeing unused kernel memory: 236k init INIT: version 2.78 booting Activating swap... Checking all file systems... Parallelizing fsck version 1.22 (22-Jun-2001) Mounting local filesystems... nothing was mounted Cleaning: /etc/network/ifstate. Setting up IP spoofing protection: FAILED Configuring network interfaces: done. Starting portmap daemon: portmap. Cleaning: /tmp /var/lock /var/run. INIT: Entering runlevel: 2 Starting system log daemon: syslogd klogd. Starting internet superserver: inetd. mpc8560ads-003 login: root Last login: Thu Jan 1 00:00:05 1970 on console Linux mpc8560ads-003 2.4.21-rc5 #2 Wed Oct 15 09:13:46 CDT 2003 ppc unknown root@mpc8560ads-003:~# ls 21142.o aa e100.o hello.o mii.o timer.o root@mpc8560ads-003:~# cd / root@mpc8560ads-003:/# ls bin boot dev etc home lib mnt opt proc root sbin tmp usr var root@mpc8560ads-003:/# /sbin/ifconfig eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4608 errors:0 dropped:0 overruns:0 frame:0 TX packets:2610 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:4465943 (4.2 Mb) TX bytes:440944 (430.6 Kb) Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:296 (296.0 b) TX bytes:296 (296.0 b) root@mpc8560ads-003:/# ping 163.12.64.52 PING 163.12.64.52 (163.12.64.52): 56 data bytes 64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.1 ms 64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms 64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms --- 163.12.64.52 ping statistics --- 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 0.1/0.1/0.1 ms root@mpc8560ads-003:/#