Merge tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next

Pull MFD update from Samuel Ortiz:
 "For 3.10 we have a few new MFD drivers for:

   - The ChromeOS embedded controller which provides keyboard, battery
     and power management services.  This controller is accessible
     through i2c or SPI.

   - Silicon Laboratories 476x controller, providing access to their FM
     chipset and their audio codec.

   - Realtek's RTS5249, a memory stick, MMC and SD/SDIO PCI based
     reader.

   - Nokia's Tahvo power button and watchdog device.  This device is
     very similar to Retu and is thus supported by the same code base.

   - STMicroelectronics STMPE1801, a keyboard and GPIO controller
     supported by the stmpe driver.

   - ST-Ericsson AB8540 and AB8505 power management and voltage
     converter controllers through the existing ab8500 code.

  Some other drivers got cleaned up or improved.  In particular:

   - The Linaro/STE guys got the ab8500 driver in sync with their
     internal code through a series of optimizations, fixes and
     improvements.

   - The AS3711 and OMAP USB drivers now have DT support.

   - The arizona clock and interrupt handling code got improved.

   - The wm5102 register patch and boot mechanism also got improved."

* tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (104 commits)
  mfd: si476x: Don't use 0bNNN
  mfd: vexpress: Handle pending config transactions
  mfd: ab8500: Export ab8500_gpadc_sw_hw_convert properly
  mfd: si476x: Fix i2c warning
  mfd: si476x: Add header files and Kbuild plumbing
  mfd: si476x: Add chip properties handling code
  mfd: si476x: Add the bulk of the core driver
  mfd: si476x: Add commands abstraction layer
  mfd: rtsx: Support RTS5249
  mfd: retu: Add Tahvo support
  mfd: ucb1400: Pass ucb1400-gpio data through ac97 bus
  mfd: wm8994: Add some OF properties
  mfd: wm8994: Add device ID data to WM8994 OF device IDs
  input: Export matrix_keypad_parse_of_params()
  mfd: tps65090: Add compatible string for charger subnode
  mfd: db8500-prcmu: Support platform dependant device selection
  mfd: syscon: Fix warnings when printing resource_size_t
  of: Add stub of_get_parent for non-OF builds
  mfd: omap-usb-tll: Convert to devm_ioremap_resource()
  mfd: omap-usb-host: Convert to devm_ioremap_resource()
  ...

1 files changed, 73 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mfd/as3711.txt b/Documentation/devicetree/bindings/mfd/as3711.txt
new file mode 100644
index 0000000..d98cf18
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/as3711.txt
@@ -0,0 +1,73 @@
+AS3711 is an I2C PMIC from Austria MicroSystems with multiple DCDC and LDO power
+supplies, a battery charger and an RTC. So far only bindings for the two stepup
+DCDC converters are defined. Other DCDC and LDO supplies are configured, using
+standard regulator properties, they must belong to a sub-node, called
+"regulators" and be called "sd1" to "sd4" and "ldo1" to "ldo8." Stepup converter
+configuration should be placed in a subnode, called "backlight."
+
+Compulsory properties:
+- compatible		: must be "ams,as3711"
+- reg			: specifies the I2C address
+
+To use the SU1 converter as a backlight source the following two properties must
+be provided:
+- su1-dev		: framebuffer phandle
+- su1-max-uA		: maximum current
+
+To use the SU2 converter as a backlight source the following two properties must
+be provided:
+- su2-dev		: framebuffer phandle
+- su1-max-uA		: maximum current
+
+Additionally one of these properties must be provided to select the type of
+feedback used:
+- su2-feedback-voltage	: voltage feedback is used
+- su2-feedback-curr1	: CURR1 input used for current feedback
+- su2-feedback-curr2	: CURR2 input used for current feedback
+- su2-feedback-curr3	: CURR3 input used for current feedback
+- su2-feedback-curr-auto: automatic current feedback selection
+
+and one of these to select the over-voltage protection pin
+- su2-fbprot-lx-sd4	: LX_SD4 is used for over-voltage protection
+- su2-fbprot-gpio2	: GPIO2 is used for over-voltage protection
+- su2-fbprot-gpio3	: GPIO3 is used for over-voltage protection
+- su2-fbprot-gpio4	: GPIO4 is used for over-voltage protection
+
+If "su2-feedback-curr-auto" is selected, one or more of the following properties
+have to be specified:
+- su2-auto-curr1	: use CURR1 input for current feedback
+- su2-auto-curr2	: use CURR2 input for current feedback
+- su2-auto-curr3	: use CURR3 input for current feedback
+
+Example:
+
+as3711@40 {
+	compatible = "ams,as3711";
+	reg = <0x40>;
+
+	regulators {
+		sd4 {
+			regulator-name = "1.215V";
+			regulator-min-microvolt = <1215000>;
+			regulator-max-microvolt = <1235000>;
+		};
+		ldo2 {
+			regulator-name = "2.8V CPU";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+	};
+
+	backlight {
+		compatible = "ams,as3711-bl";
+		su2-dev = <&lcdc>;
+		su2-max-uA = <36000>;
+		su2-feedback-curr-auto;
+		su2-fbprot-gpio4;
+		su2-auto-curr1;
+		su2-auto-curr2;
+		su2-auto-curr3;
+	};
+};