Merge tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next

Pull MFD update from Samuel Ortiz:
 "For 3.10 we have a few new MFD drivers for:

   - The ChromeOS embedded controller which provides keyboard, battery
     and power management services.  This controller is accessible
     through i2c or SPI.

   - Silicon Laboratories 476x controller, providing access to their FM
     chipset and their audio codec.

   - Realtek's RTS5249, a memory stick, MMC and SD/SDIO PCI based
     reader.

   - Nokia's Tahvo power button and watchdog device.  This device is
     very similar to Retu and is thus supported by the same code base.

   - STMicroelectronics STMPE1801, a keyboard and GPIO controller
     supported by the stmpe driver.

   - ST-Ericsson AB8540 and AB8505 power management and voltage
     converter controllers through the existing ab8500 code.

  Some other drivers got cleaned up or improved.  In particular:

   - The Linaro/STE guys got the ab8500 driver in sync with their
     internal code through a series of optimizations, fixes and
     improvements.

   - The AS3711 and OMAP USB drivers now have DT support.

   - The arizona clock and interrupt handling code got improved.

   - The wm5102 register patch and boot mechanism also got improved."

* tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (104 commits)
  mfd: si476x: Don't use 0bNNN
  mfd: vexpress: Handle pending config transactions
  mfd: ab8500: Export ab8500_gpadc_sw_hw_convert properly
  mfd: si476x: Fix i2c warning
  mfd: si476x: Add header files and Kbuild plumbing
  mfd: si476x: Add chip properties handling code
  mfd: si476x: Add the bulk of the core driver
  mfd: si476x: Add commands abstraction layer
  mfd: rtsx: Support RTS5249
  mfd: retu: Add Tahvo support
  mfd: ucb1400: Pass ucb1400-gpio data through ac97 bus
  mfd: wm8994: Add some OF properties
  mfd: wm8994: Add device ID data to WM8994 OF device IDs
  input: Export matrix_keypad_parse_of_params()
  mfd: tps65090: Add compatible string for charger subnode
  mfd: db8500-prcmu: Support platform dependant device selection
  mfd: syscon: Fix warnings when printing resource_size_t
  of: Add stub of_get_parent for non-OF builds
  mfd: omap-usb-tll: Convert to devm_ioremap_resource()
  mfd: omap-usb-host: Convert to devm_ioremap_resource()
  ...

1 files changed, 80 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
new file mode 100644
index 0000000..b381fa6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt
@@ -0,0 +1,80 @@
+OMAP HS USB Host
+
+Required properties:
+
+- compatible: should be "ti,usbhs-host"
+- reg: should contain one register range i.e. start and length
+- ti,hwmods: must contain "usb_host_hs"
+
+Optional properties:
+
+- num-ports: number of USB ports. Usually this is automatically detected
+  from the IP's revision register but can be overridden by specifying
+  this property. A maximum of 3 ports are supported at the moment.
+
+- portN-mode: String specifying the port mode for port N, where N can be
+  from 1 to 3. If the port mode is not specified, that port is treated
+  as unused. When specified, it must be one of the following.
+	"ehci-phy",
+        "ehci-tll",
+        "ehci-hsic",
+        "ohci-phy-6pin-datse0",
+        "ohci-phy-6pin-dpdm",
+        "ohci-phy-3pin-datse0",
+        "ohci-phy-4pin-dpdm",
+        "ohci-tll-6pin-datse0",
+        "ohci-tll-6pin-dpdm",
+        "ohci-tll-3pin-datse0",
+        "ohci-tll-4pin-dpdm",
+        "ohci-tll-2pin-datse0",
+        "ohci-tll-2pin-dpdm",
+
+- single-ulpi-bypass: Must be present if the controller contains a single
+  ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1
+
+Required properties if child node exists:
+
+- #address-cells: Must be 1
+- #size-cells: Must be 1
+- ranges: must be present
+
+Properties for children:
+
+The OMAP HS USB Host subsystem contains EHCI and OHCI controllers.
+See Documentation/devicetree/bindings/usb/omap-ehci.txt and
+omap3-ohci.txt
+
+Example for OMAP4:
+
+usbhshost: usbhshost@4a064000 {
+	compatible = "ti,usbhs-host";
+	reg = <0x4a064000 0x800>;
+	ti,hwmods = "usb_host_hs";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	usbhsohci: ohci@4a064800 {
+		compatible = "ti,ohci-omap3", "usb-ohci";
+		reg = <0x4a064800 0x400>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 76 0x4>;
+	};
+
+	usbhsehci: ehci@4a064c00 {
+		compatible = "ti,ehci-omap", "usb-ehci";
+		reg = <0x4a064c00 0x400>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 77 0x4>;
+	};
+};
+
+&usbhshost {
+	port1-mode = "ehci-phy";
+	port2-mode = "ehci-tll";
+	port3-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy 0 &hsusb3_phy>;
+};