diff options
author | Eliezer Tamir <eliezert@broadcom.com> | 2008-02-28 19:51:50 (GMT) |
---|---|---|
committer | David S. Miller <davem@davemloft.net> | 2008-02-28 19:51:50 (GMT) |
commit | f14106478e372e64be54a3cdab1e2fa83a5c8a35 (patch) | |
tree | 5d66afdfdb0e9752e6ca13b28f6e61c4d8558e39 /drivers/net/bnx2x_reg.h | |
parent | 250479504ff7d7e8c7d5cf85bedd40fb8d725429 (diff) | |
download | linux-fsl-qoriq-f14106478e372e64be54a3cdab1e2fa83a5c8a35.tar.xz |
[BNX2X]: Correct Link management
Properly protect PHY access between two devices on the same board with
a HW lock.
Use GPIO to clear all previous configurations before changing link
parameters.
Shut down the external PHY in case of fan failure.
Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.
Resolve the flow control response according to autoneg with external
PHY.
Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.
LASI indication fixes to work with peculiarities of PHYs.
Disable MAC RX to avoid a HW bug when closing the MAC under traffic.
Disable parallel detection on HiGig due to HW limitation.
Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat (limited to 'drivers/net/bnx2x_reg.h')
-rw-r--r-- | drivers/net/bnx2x_reg.h | 212 |
1 files changed, 211 insertions, 1 deletions
diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 8605529..5a1aa0b 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -1,6 +1,6 @@ /* bnx2x_reg.h: Broadcom Everest network driver. * - * Copyright (c) 2007 Broadcom Corporation + * Copyright (c) 2007-2008 Broadcom Corporation * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -24,6 +24,8 @@ #define BRB1_REG_BRB1_INT_STS 0x6011c /* [RW 4] Parity mask register #0 read/write */ #define BRB1_REG_BRB1_PRTY_MASK 0x60138 +/* [R 4] Parity register #0 read */ +#define BRB1_REG_BRB1_PRTY_STS 0x6012c /* [RW 10] At address BRB1_IND_FREE_LIST_PRS_CRDT initialize free head. At address BRB1_IND_FREE_LIST_PRS_CRDT+1 initialize free tail. At address BRB1_IND_FREE_LIST_PRS_CRDT+2 initialize parser initial credit. */ @@ -281,6 +283,8 @@ #define CDU_REG_CDU_INT_STS 0x101030 /* [RW 5] Parity mask register #0 read/write */ #define CDU_REG_CDU_PRTY_MASK 0x10104c +/* [R 5] Parity register #0 read */ +#define CDU_REG_CDU_PRTY_STS 0x101040 /* [RC 32] logging of error data in case of a CDU load error: {expected_cid[15:0]; xpected_type[2:0]; xpected_region[2:0]; ctive_error; ype_error; ctual_active; ctual_compressed_context}; */ @@ -308,6 +312,8 @@ #define CFC_REG_CFC_INT_STS_CLR 0x104100 /* [RW 4] Parity mask register #0 read/write */ #define CFC_REG_CFC_PRTY_MASK 0x104118 +/* [R 4] Parity register #0 read */ +#define CFC_REG_CFC_PRTY_STS 0x10410c /* [RW 21] CID cam access (21:1 - Data; alid - 0) */ #define CFC_REG_CID_CAM 0x104800 #define CFC_REG_CONTROL0 0x104028 @@ -354,6 +360,8 @@ #define CSDM_REG_CSDM_INT_MASK_1 0xc22ac /* [RW 11] Parity mask register #0 read/write */ #define CSDM_REG_CSDM_PRTY_MASK 0xc22bc +/* [R 11] Parity register #0 read */ +#define CSDM_REG_CSDM_PRTY_STS 0xc22b0 #define CSDM_REG_ENABLE_IN1 0xc2238 #define CSDM_REG_ENABLE_IN2 0xc223c #define CSDM_REG_ENABLE_OUT1 0xc2240 @@ -438,6 +446,9 @@ /* [RW 32] Parity mask register #0 read/write */ #define CSEM_REG_CSEM_PRTY_MASK_0 0x200130 #define CSEM_REG_CSEM_PRTY_MASK_1 0x200140 +/* [R 32] Parity register #0 read */ +#define CSEM_REG_CSEM_PRTY_STS_0 0x200124 +#define CSEM_REG_CSEM_PRTY_STS_1 0x200134 #define CSEM_REG_ENABLE_IN 0x2000a4 #define CSEM_REG_ENABLE_OUT 0x2000a8 /* [RW 32] This address space contains all registers and memories that are @@ -526,6 +537,8 @@ #define CSEM_REG_TS_9_AS 0x20005c /* [RW 1] Parity mask register #0 read/write */ #define DBG_REG_DBG_PRTY_MASK 0xc0a8 +/* [R 1] Parity register #0 read */ +#define DBG_REG_DBG_PRTY_STS 0xc09c /* [RW 2] debug only: These bits indicate the credit for PCI request type 4 interface; MUST be configured AFTER pci_ext_buffer_strt_addr_lsb/msb are configured */ @@ -543,6 +556,8 @@ #define DMAE_REG_DMAE_INT_MASK 0x102054 /* [RW 4] Parity mask register #0 read/write */ #define DMAE_REG_DMAE_PRTY_MASK 0x102064 +/* [R 4] Parity register #0 read */ +#define DMAE_REG_DMAE_PRTY_STS 0x102058 /* [RW 1] Command 0 go. */ #define DMAE_REG_GO_C0 0x102080 /* [RW 1] Command 1 go. */ @@ -623,6 +638,8 @@ #define DORQ_REG_DORQ_INT_STS_CLR 0x170178 /* [RW 2] Parity mask register #0 read/write */ #define DORQ_REG_DORQ_PRTY_MASK 0x170190 +/* [R 2] Parity register #0 read */ +#define DORQ_REG_DORQ_PRTY_STS 0x170184 /* [RW 8] The address to write the DPM CID to STORM. */ #define DORQ_REG_DPM_CID_ADDR 0x170044 /* [RW 5] The DPM mode CID extraction offset. */ @@ -692,6 +709,8 @@ #define HC_REG_CONFIG_1 0x108004 /* [RW 3] Parity mask register #0 read/write */ #define HC_REG_HC_PRTY_MASK 0x1080a0 +/* [R 3] Parity register #0 read */ +#define HC_REG_HC_PRTY_STS 0x108094 /* [RW 17] status block interrupt mask; one in each bit means unmask; zerow in each bit means mask; bit 0 - default SB; bit 1 - SB_0; bit 2 - SB_1... bit 16- SB_15; addr 0 - port 0; addr 1 - port 1 */ @@ -1127,6 +1146,7 @@ #define MISC_REG_AEU_GENERAL_ATTN_17 0xa044 #define MISC_REG_AEU_GENERAL_ATTN_18 0xa048 #define MISC_REG_AEU_GENERAL_ATTN_19 0xa04c +#define MISC_REG_AEU_GENERAL_ATTN_10 0xa028 #define MISC_REG_AEU_GENERAL_ATTN_11 0xa02c #define MISC_REG_AEU_GENERAL_ATTN_2 0xa008 #define MISC_REG_AEU_GENERAL_ATTN_20 0xa050 @@ -1135,6 +1155,9 @@ #define MISC_REG_AEU_GENERAL_ATTN_4 0xa010 #define MISC_REG_AEU_GENERAL_ATTN_5 0xa014 #define MISC_REG_AEU_GENERAL_ATTN_6 0xa018 +#define MISC_REG_AEU_GENERAL_ATTN_7 0xa01c +#define MISC_REG_AEU_GENERAL_ATTN_8 0xa020 +#define MISC_REG_AEU_GENERAL_ATTN_9 0xa024 /* [RW 32] first 32b for inverting the input for function 0; for each bit: 0= do not invert; 1= invert; mapped as follows: [0] NIG attention for function0; [1] NIG attention for function1; [2] GPIO1 mcp; [3] GPIO2 mcp; @@ -1183,6 +1206,40 @@ starts at 0x0 for the A0 tape-out and increments by one for each all-layer tape-out. */ #define MISC_REG_CHIP_REV 0xa40c +/* [RW 32] The following driver registers(1..6) represent 6 drivers and 32 + clients. Each client can be controlled by one driver only. One in each + bit represent that this driver control the appropriate client (Ex: bit 5 + is set means this driver control client number 5). addr1 = set; addr0 = + clear; read from both addresses will give the same result = status. write + to address 1 will set a request to control all the clients that their + appropriate bit (in the write command) is set. if the client is free (the + appropriate bit in all the other drivers is clear) one will be written to + that driver register; if the client isn't free the bit will remain zero. + if the appropriate bit is set (the driver request to gain control on a + client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW + interrupt will be asserted). write to address 0 will set a request to + free all the clients that their appropriate bit (in the write command) is + set. if the appropriate bit is clear (the driver request to free a client + it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will + be asserted). */ +#define MISC_REG_DRIVER_CONTROL_1 0xa510 +/* [RW 32] GPIO. [31-28] FLOAT port 0; [27-24] FLOAT port 0; When any of + these bits is written as a '1'; the corresponding SPIO bit will turn off + it's drivers and become an input. This is the reset state of all GPIO + pins. The read value of these bits will be a '1' if that last command + (#SET; #CLR; or #FLOAT) for this bit was a #FLOAT. (reset value 0xff). + [23-20] CLR port 1; 19-16] CLR port 0; When any of these bits is written + as a '1'; the corresponding GPIO bit will drive low. The read value of + these bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for + this bit was a #CLR. (reset value 0). [15-12] SET port 1; 11-8] port 0; + SET When any of these bits is written as a '1'; the corresponding GPIO + bit will drive high (if it has that capability). The read value of these + bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for this + bit was a #SET. (reset value 0). [7-4] VALUE port 1; [3-0] VALUE port 0; + RO; These bits indicate the read value of each of the eight GPIO pins. + This is the result value of the pin; not the drive value. Writing these + bits will have not effect. */ +#define MISC_REG_GPIO 0xa490 /* [RW 1] Setting this bit enables a timer in the GRC block to timeout any access that does not finish within ~misc_registers_grc_timout_val.grc_timeout_val cycles. When this bit is @@ -1223,6 +1280,8 @@ #define MISC_REG_MISC_INT_MASK 0xa388 /* [RW 1] Parity mask register #0 read/write */ #define MISC_REG_MISC_PRTY_MASK 0xa398 +/* [R 1] Parity register #0 read */ +#define MISC_REG_MISC_PRTY_STS 0xa38c /* [RW 32] 32 LSB of storm PLL first register; reset val = 0x 071d2911. inside order of the bits is: [0] P1 divider[0] (reset value 1); [1] P1 divider[1] (reset value 0); [2] P1 divider[2] (reset value 0); [3] P1 @@ -1264,6 +1323,55 @@ /* [RW 20] 20 bit GRC address where the scratch-pad of the MCP that is shared with the driver resides */ #define MISC_REG_SHARED_MEM_ADDR 0xa2b4 +/* [RW 32] SPIO. [31-24] FLOAT When any of these bits is written as a '1'; + the corresponding SPIO bit will turn off it's drivers and become an + input. This is the reset state of all SPIO pins. The read value of these + bits will be a '1' if that last command (#SET; #CL; or #FLOAT) for this + bit was a #FLOAT. (reset value 0xff). [23-16] CLR When any of these bits + is written as a '1'; the corresponding SPIO bit will drive low. The read + value of these bits will be a '1' if that last command (#SET; #CLR; or +#FLOAT) for this bit was a #CLR. (reset value 0). [15-8] SET When any of + these bits is written as a '1'; the corresponding SPIO bit will drive + high (if it has that capability). The read value of these bits will be a + '1' if that last command (#SET; #CLR; or #FLOAT) for this bit was a #SET. + (reset value 0). [7-0] VALUE RO; These bits indicate the read value of + each of the eight SPIO pins. This is the result value of the pin; not the + drive value. Writing these bits will have not effect. Each 8 bits field + is divided as follows: [0] VAUX Enable; when pulsed low; enables supply + from VAUX. (This is an output pin only; the FLOAT field is not applicable + for this pin); [1] VAUX Disable; when pulsed low; disables supply form + VAUX. (This is an output pin only; FLOAT field is not applicable for this + pin); [2] SEL_VAUX_B - Control to power switching logic. Drive low to + select VAUX supply. (This is an output pin only; it is not controlled by + the SET and CLR fields; it is controlled by the Main Power SM; the FLOAT + field is not applicable for this pin; only the VALUE fields is relevant - + it reflects the output value); [3] reserved; [4] spio_4; [5] spio_5; [6] + Bit 0 of UMP device ID select; read by UMP firmware; [7] Bit 1 of UMP + device ID select; read by UMP firmware. */ +#define MISC_REG_SPIO 0xa4fc +/* [RW 8] These bits enable the SPIO_INTs to signals event to the IGU/MC. + according to the following map: [3:0] reserved; [4] spio_4 [5] spio_5; + [7:0] reserved */ +#define MISC_REG_SPIO_EVENT_EN 0xa2b8 +/* [RW 32] SPIO INT. [31-24] OLD_CLR Writing a '1' to these bit clears the + corresponding bit in the #OLD_VALUE register. This will acknowledge an + interrupt on the falling edge of corresponding SPIO input (reset value + 0). [23-16] OLD_SET Writing a '1' to these bit sets the corresponding bit + in the #OLD_VALUE register. This will acknowledge an interrupt on the + rising edge of corresponding SPIO input (reset value 0). [15-8] OLD_VALUE + RO; These bits indicate the old value of the SPIO input value. When the + ~INT_STATE bit is set; this bit indicates the OLD value of the pin such + that if ~INT_STATE is set and this bit is '0'; then the interrupt is due + to a low to high edge. If ~INT_STATE is set and this bit is '1'; then the + interrupt is due to a high to low edge (reset value 0). [7-0] INT_STATE + RO; These bits indicate the current SPIO interrupt state for each SPIO + pin. This bit is cleared when the appropriate #OLD_SET or #OLD_CLR + command bit is written. This bit is set when the SPIO input does not + match the current value in #OLD_VALUE (reset value 0). */ +#define MISC_REG_SPIO_INT 0xa500 +/* [RW 1] Set by the MCP to remember if one or more of the drivers is/are + loaded; 0-prepare; -unprepare */ +#define MISC_REG_UNPREPARED 0xa424 #define NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT (0x1<<0) #define NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS (0x1<<9) #define NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G (0x1<<15) @@ -1392,6 +1500,9 @@ #define NIG_REG_NIG_INGRESS_EMAC0_NO_CRC 0x10044 /* [RW 1] Input enable for RX PBF LP IF */ #define NIG_REG_PBF_LB_IN_EN 0x100b4 +/* [RW 1] Value of this register will be transmitted to port swap when + ~nig_registers_strap_override.strap_override =1 */ +#define NIG_REG_PORT_SWAP 0x10394 /* [RW 1] output enable for RX parser descriptor IF */ #define NIG_REG_PRS_EOP_OUT_EN 0x10104 /* [RW 1] Input enable for RX parser request IF */ @@ -1410,6 +1521,10 @@ #define NIG_REG_STAT2_BRB_OCTET 0x107e0 #define NIG_REG_STATUS_INTERRUPT_PORT0 0x10328 #define NIG_REG_STATUS_INTERRUPT_PORT1 0x1032c +/* [RW 1] port swap mux selection. If this register equal to 0 then port + swap is equal to SPIO pin that inputs from ifmux_serdes_swap. If 1 then + ort swap is equal to ~nig_registers_port_swap.port_swap */ +#define NIG_REG_STRAP_OVERRIDE 0x10398 /* [RW 1] output enable for RX_XCM0 IF */ #define NIG_REG_XCM0_OUT_EN 0x100f0 /* [RW 1] output enable for RX_XCM1 IF */ @@ -1499,6 +1614,8 @@ #define PB_REG_PB_INT_STS 0x1c /* [RW 4] Parity mask register #0 read/write */ #define PB_REG_PB_PRTY_MASK 0x38 +/* [R 4] Parity register #0 read */ +#define PB_REG_PB_PRTY_STS 0x2c #define PRS_REG_A_PRSU_20 0x40134 /* [R 8] debug only: CFC load request current credit. Transaction based. */ #define PRS_REG_CFC_LD_CURRENT_CREDIT 0x40164 @@ -1590,6 +1707,8 @@ #define PRS_REG_PRS_INT_STS 0x40188 /* [RW 8] Parity mask register #0 read/write */ #define PRS_REG_PRS_PRTY_MASK 0x401a4 +/* [R 8] Parity register #0 read */ +#define PRS_REG_PRS_PRTY_STS 0x40198 /* [RW 8] Context region for pure acknowledge packets. Used in CFC load request message */ #define PRS_REG_PURE_REGIONS 0x40024 @@ -1718,6 +1837,9 @@ /* [RW 32] Parity mask register #0 read/write */ #define PXP2_REG_PXP2_PRTY_MASK_0 0x120588 #define PXP2_REG_PXP2_PRTY_MASK_1 0x120598 +/* [R 32] Parity register #0 read */ +#define PXP2_REG_PXP2_PRTY_STS_0 0x12057c +#define PXP2_REG_PXP2_PRTY_STS_1 0x12058c /* [R 1] Debug only: The 'almost full' indication from each fifo (gives indication about backpressure) */ #define PXP2_REG_RD_ALMOST_FULL_0 0x120424 @@ -1911,6 +2033,8 @@ #define PXP2_REG_RQ_HC_ENDIAN_M 0x1201a8 /* [WB 53] Onchip address table */ #define PXP2_REG_RQ_ONCHIP_AT 0x122000 +/* [RW 13] Pending read limiter threshold; in Dwords */ +#define PXP2_REG_RQ_PDR_LIMIT 0x12033c /* [RW 2] Endian mode for qm */ #define PXP2_REG_RQ_QM_ENDIAN_M 0x120194 /* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k; @@ -1921,6 +2045,9 @@ /* [RW 3] Max burst size filed for read requests port 0; 000 - 128B; 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */ #define PXP2_REG_RQ_RD_MBS0 0x120160 +/* [RW 3] Max burst size filed for read requests port 1; 000 - 128B; + 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */ +#define PXP2_REG_RQ_RD_MBS1 0x120168 /* [RW 2] Endian mode for src */ #define PXP2_REG_RQ_SRC_ENDIAN_M 0x12019c /* [RW 3] page size in L2P table for SRC module; -4k; -8k; -16k; -32k; -64k; @@ -2000,10 +2127,17 @@ /* [RW 3] Max burst size filed for write requests port 0; 000 - 128B; 001:256B; 010: 512B; */ #define PXP2_REG_RQ_WR_MBS0 0x12015c +/* [RW 3] Max burst size filed for write requests port 1; 000 - 128B; + 001:256B; 010: 512B; */ +#define PXP2_REG_RQ_WR_MBS1 0x120164 /* [RW 10] if Number of entries in dmae fifo will be higer than this threshold then has_payload indication will be asserted; the default value should be equal to > write MBS size! */ #define PXP2_REG_WR_DMAE_TH 0x120368 +/* [RW 10] if Number of entries in usdmdp fifo will be higer than this + threshold then has_payload indication will be asserted; the default value + should be equal to > write MBS size! */ +#define PXP2_REG_WR_USDMDP_TH 0x120348 /* [R 1] debug only: Indication if PSWHST arbiter is idle */ #define PXP_REG_HST_ARB_IS_IDLE 0x103004 /* [R 8] debug only: A bit mask for all PSWHST arbiter clients. '1' means @@ -2021,6 +2155,8 @@ #define PXP_REG_PXP_INT_STS_CLR_0 0x10306c /* [RW 26] Parity mask register #0 read/write */ #define PXP_REG_PXP_PRTY_MASK 0x103094 +/* [R 26] Parity register #0 read */ +#define PXP_REG_PXP_PRTY_STS 0x103088 /* [RW 4] The activity counter initial increment value sent in the load request */ #define QM_REG_ACTCTRINITVAL_0 0x168040 @@ -2127,6 +2263,8 @@ #define QM_REG_QM_INT_STS 0x168438 /* [RW 9] Parity mask register #0 read/write */ #define QM_REG_QM_PRTY_MASK 0x168454 +/* [R 9] Parity register #0 read */ +#define QM_REG_QM_PRTY_STS 0x168448 /* [R 32] Current queues in pipeline: Queues from 32 to 63 */ #define QM_REG_QSTATUS_HIGH 0x16802c /* [R 32] Current queues in pipeline: Queues from 0 to 31 */ @@ -2410,6 +2548,8 @@ #define SRC_REG_SRC_INT_STS 0x404ac /* [RW 3] Parity mask register #0 read/write */ #define SRC_REG_SRC_PRTY_MASK 0x404c8 +/* [R 3] Parity register #0 read */ +#define SRC_REG_SRC_PRTY_STS 0x404bc /* [R 4] Used to read the value of the XX protection CAM occupancy counter. */ #define TCM_REG_CAM_OCCUP 0x5017c /* [RW 1] CDU AG read Interface enable. If 0 - the request input is @@ -2730,6 +2870,8 @@ #define TSDM_REG_TSDM_INT_MASK_1 0x422ac /* [RW 11] Parity mask register #0 read/write */ #define TSDM_REG_TSDM_PRTY_MASK 0x422bc +/* [R 11] Parity register #0 read */ +#define TSDM_REG_TSDM_PRTY_STS 0x422b0 /* [RW 5] The number of time_slots in the arbitration cycle */ #define TSEM_REG_ARB_CYCLE_SIZE 0x180034 /* [RW 3] The source that is associated with arbitration element 0. Source @@ -2854,6 +2996,9 @@ /* [RW 32] Parity mask register #0 read/write */ #define TSEM_REG_TSEM_PRTY_MASK_0 0x180120 #define TSEM_REG_TSEM_PRTY_MASK_1 0x180130 +/* [R 32] Parity register #0 read */ +#define TSEM_REG_TSEM_PRTY_STS_0 0x180114 +#define TSEM_REG_TSEM_PRTY_STS_1 0x180124 /* [R 5] Used to read the XX protection CAM occupancy counter. */ #define UCM_REG_CAM_OCCUP 0xe0170 /* [RW 1] CDU AG read Interface enable. If 0 - the request input is @@ -3155,6 +3300,8 @@ #define USDM_REG_USDM_INT_MASK_1 0xc42b0 /* [RW 11] Parity mask register #0 read/write */ #define USDM_REG_USDM_PRTY_MASK 0xc42c0 +/* [R 11] Parity register #0 read */ +#define USDM_REG_USDM_PRTY_STS 0xc42b4 /* [RW 5] The number of time_slots in the arbitration cycle */ #define USEM_REG_ARB_CYCLE_SIZE 0x300034 /* [RW 3] The source that is associated with arbitration element 0. Source @@ -3279,6 +3426,9 @@ /* [RW 32] Parity mask register #0 read/write */ #define USEM_REG_USEM_PRTY_MASK_0 0x300130 #define USEM_REG_USEM_PRTY_MASK_1 0x300140 +/* [R 32] Parity register #0 read */ +#define USEM_REG_USEM_PRTY_STS_0 0x300124 +#define USEM_REG_USEM_PRTY_STS_1 0x300134 /* [RW 2] The queue index for registration on Aux1 counter flag. */ #define XCM_REG_AUX1_Q 0x20134 /* [RW 2] Per each decision rule the queue index to register to. */ @@ -3684,6 +3834,8 @@ #define XSDM_REG_XSDM_INT_MASK_1 0x1662ac /* [RW 11] Parity mask register #0 read/write */ #define XSDM_REG_XSDM_PRTY_MASK 0x1662bc +/* [R 11] Parity register #0 read */ +#define XSDM_REG_XSDM_PRTY_STS 0x1662b0 /* [RW 5] The number of time_slots in the arbitration cycle */ #define XSEM_REG_ARB_CYCLE_SIZE 0x280034 /* [RW 3] The source that is associated with arbitration element 0. Source @@ -3808,6 +3960,9 @@ /* [RW 32] Parity mask register #0 read/write */ #define XSEM_REG_XSEM_PRTY_MASK_0 0x280130 #define XSEM_REG_XSEM_PRTY_MASK_1 0x280140 +/* [R 32] Parity register #0 read */ +#define XSEM_REG_XSEM_PRTY_STS_0 0x280124 +#define XSEM_REG_XSEM_PRTY_STS_1 0x280134 #define MCPR_NVM_ACCESS_ENABLE_EN (1L<<0) #define MCPR_NVM_ACCESS_ENABLE_WR_EN (1L<<1) #define MCPR_NVM_ADDR_NVM_ADDR_VALUE (0xffffffL<<0) @@ -3847,6 +4002,8 @@ #define EMAC_MDIO_COMM_START_BUSY (1L<<29) #define EMAC_MDIO_MODE_AUTO_POLL (1L<<4) #define EMAC_MDIO_MODE_CLAUSE_45 (1L<<31) +#define EMAC_MDIO_MODE_CLOCK_CNT (0x3fL<<16) +#define EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT 16 #define EMAC_MODE_25G_MODE (1L<<5) #define EMAC_MODE_ACPI_RCVD (1L<<20) #define EMAC_MODE_HALF_DUPLEX (1L<<1) @@ -3874,6 +4031,17 @@ #define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31) #define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3) #define EMAC_TX_MODE_RESET (1L<<0) +#define MISC_REGISTERS_GPIO_1 1 +#define MISC_REGISTERS_GPIO_2 2 +#define MISC_REGISTERS_GPIO_3 3 +#define MISC_REGISTERS_GPIO_CLR_POS 16 +#define MISC_REGISTERS_GPIO_FLOAT (0xffL<<24) +#define MISC_REGISTERS_GPIO_FLOAT_POS 24 +#define MISC_REGISTERS_GPIO_INPUT_HI_Z 2 +#define MISC_REGISTERS_GPIO_OUTPUT_HIGH 1 +#define MISC_REGISTERS_GPIO_OUTPUT_LOW 0 +#define MISC_REGISTERS_GPIO_PORT_SHIFT 4 +#define MISC_REGISTERS_GPIO_SET_POS 8 #define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588 #define MISC_REGISTERS_RESET_REG_1_SET 0x584 #define MISC_REGISTERS_RESET_REG_2_CLEAR 0x598 @@ -3891,6 +4059,25 @@ #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW (0x1<<4) #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB (0x1<<8) #define MISC_REGISTERS_RESET_REG_3_SET 0x5a4 +#define MISC_REGISTERS_SPIO_4 4 +#define MISC_REGISTERS_SPIO_5 5 +#define MISC_REGISTERS_SPIO_7 7 +#define MISC_REGISTERS_SPIO_CLR_POS 16 +#define MISC_REGISTERS_SPIO_FLOAT (0xffL<<24) +#define GRC_MISC_REGISTERS_SPIO_FLOAT7 0x80000000 +#define GRC_MISC_REGISTERS_SPIO_FLOAT6 0x40000000 +#define GRC_MISC_REGISTERS_SPIO_FLOAT5 0x20000000 +#define GRC_MISC_REGISTERS_SPIO_FLOAT4 0x10000000 +#define MISC_REGISTERS_SPIO_FLOAT_POS 24 +#define MISC_REGISTERS_SPIO_INPUT_HI_Z 2 +#define MISC_REGISTERS_SPIO_INT_OLD_SET_POS 16 +#define MISC_REGISTERS_SPIO_OUTPUT_HIGH 1 +#define MISC_REGISTERS_SPIO_OUTPUT_LOW 0 +#define MISC_REGISTERS_SPIO_SET_POS 8 +#define HW_LOCK_MAX_RESOURCE_VALUE 31 +#define HW_LOCK_RESOURCE_8072_MDIO 0 +#define HW_LOCK_RESOURCE_GPIO 1 +#define HW_LOCK_RESOURCE_SPIO 2 #define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (1<<18) #define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (1<<31) #define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (1<<9) @@ -3918,6 +4105,7 @@ #define AEU_INPUTS_ATTN_BITS_QM_HW_INTERRUPT (1<<3) #define AEU_INPUTS_ATTN_BITS_QM_PARITY_ERROR (1<<2) #define AEU_INPUTS_ATTN_BITS_SEARCHER_PARITY_ERROR (1<<22) +#define AEU_INPUTS_ATTN_BITS_SPIO5 (1<<15) #define AEU_INPUTS_ATTN_BITS_TCM_HW_INTERRUPT (1<<27) #define AEU_INPUTS_ATTN_BITS_TIMERS_HW_INTERRUPT (1<<5) #define AEU_INPUTS_ATTN_BITS_TSDM_HW_INTERRUPT (1<<25) @@ -4206,6 +4394,9 @@ #define MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE 0x4000 #define MDIO_XGXS_BLOCK2_TX_LN_SWAP 0x11 #define MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE 0x8000 +#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G 0x14 +#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS 0x0001 +#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS 0x0010 #define MDIO_XGXS_BLOCK2_TEST_MODE_LANE 0x15 #define MDIO_REG_BANK_GP_STATUS 0x8120 @@ -4362,11 +4553,13 @@ #define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_SGMII_MODE 0x0001 +#define EXT_PHY_AUTO_NEG_DEVAD 0x7 #define EXT_PHY_OPT_PMA_PMD_DEVAD 0x1 #define EXT_PHY_OPT_WIS_DEVAD 0x2 #define EXT_PHY_OPT_PCS_DEVAD 0x3 #define EXT_PHY_OPT_PHY_XS_DEVAD 0x4 #define EXT_PHY_OPT_CNTL 0x0 +#define EXT_PHY_OPT_CNTL2 0x7 #define EXT_PHY_OPT_PMD_RX_SD 0xa #define EXT_PHY_OPT_PMD_MISC_CNTL 0xca0a #define EXT_PHY_OPT_PHY_IDENTIFIER 0xc800 @@ -4378,11 +4571,24 @@ #define EXT_PHY_OPT_LASI_STATUS 0x9005 #define EXT_PHY_OPT_PCS_STATUS 0x0020 #define EXT_PHY_OPT_XGXS_LANE_STATUS 0x0018 +#define EXT_PHY_OPT_AN_LINK_STATUS 0x8304 +#define EXT_PHY_OPT_AN_CL37_CL73 0x8370 +#define EXT_PHY_OPT_AN_CL37_FD 0xffe4 +#define EXT_PHY_OPT_AN_CL37_AN 0xffe0 +#define EXT_PHY_OPT_AN_ADV 0x11 #define EXT_PHY_KR_PMA_PMD_DEVAD 0x1 #define EXT_PHY_KR_PCS_DEVAD 0x3 #define EXT_PHY_KR_AUTO_NEG_DEVAD 0x7 #define EXT_PHY_KR_CTRL 0x0000 +#define EXT_PHY_KR_STATUS 0x0001 +#define EXT_PHY_KR_AUTO_NEG_COMPLETE 0x0020 +#define EXT_PHY_KR_AUTO_NEG_ADVERT 0x0010 +#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE 0x0400 +#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_ASYMMETRIC 0x0800 +#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_BOTH 0x0C00 +#define EXT_PHY_KR_AUTO_NEG_ADVERT_PAUSE_MASK 0x0C00 +#define EXT_PHY_KR_LP_AUTO_NEG 0x0013 #define EXT_PHY_KR_CTRL2 0x0007 #define EXT_PHY_KR_PCS_STATUS 0x0020 #define EXT_PHY_KR_PMD_CTRL 0x0096 @@ -4391,4 +4597,8 @@ #define EXT_PHY_KR_MISC_CTRL1 0xca85 #define EXT_PHY_KR_GEN_CTRL 0xca10 #define EXT_PHY_KR_ROM_CODE 0xca19 +#define EXT_PHY_KR_ROM_RESET_INTERNAL_MP 0x0188 +#define EXT_PHY_KR_ROM_MICRO_RESET 0x018a + +#define EXT_PHY_SFX7101_XGXS_TEST1 0xc00a |