[SCSI] mpt2sas: New feature - Fast Load Support

New feature Fast Load Support.

(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.

(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.

(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.

Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

1 files changed, 22 insertions, 4 deletions

diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.h b/drivers/scsi/mpt2sas/mpt2sas_base.h
index 59354db..ce2bd9b 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.h
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.h
@@ -655,7 +655,12 @@ enum mutex_type {
  * @ignore_loginfos: ignore loginfos during task management
  * @remove_host: flag for when driver unloads, to avoid sending dev resets
  * @pci_error_recovery: flag to prevent ioc access until slot reset completes
- * @wait_for_port_enable_to_complete:
+ * @wait_for_discovery_to_complete: flag set at driver load time when
+ *                                               waiting on reporting devices
+ * @is_driver_loading: flag set at driver load time
+ * @port_enable_failed: flag set when port enable has failed
+ * @start_scan: flag set from scan_start callback, cleared from _mpt2sas_fw_work
+ * @start_scan_failed: means port enable failed, return's the ioc_status
  * @msix_enable: flag indicating msix is enabled
  * @msix_vector_count: number msix vectors
  * @cpu_msix_table: table for mapping cpus to msix index
@@ -790,15 +795,20 @@ struct MPT2SAS_ADAPTER {
 	u8		shost_recovery;
 
 	struct mutex	reset_in_progress_mutex;
-	struct completion	shost_recovery_done;
 	spinlock_t 	ioc_reset_in_progress_lock;
 	u8		ioc_link_reset_in_progress;
-	int		ioc_reset_in_progress_status;
+	u8		ioc_reset_in_progress_status;
 
 	u8		ignore_loginfos;
 	u8		remove_host;
 	u8		pci_error_recovery;
-	u8		wait_for_port_enable_to_complete;
+	u8		wait_for_discovery_to_complete;
+	struct completion	port_enable_done;
+	u8		is_driver_loading;
+	u8		port_enable_failed;
+
+	u8		start_scan;
+	u16		start_scan_failed;
 
 	u8		msix_enable;
 	u16		msix_vector_count;
@@ -814,11 +824,13 @@ struct MPT2SAS_ADAPTER {
 	u8		scsih_cb_idx;
 	u8		ctl_cb_idx;
 	u8		base_cb_idx;
+	u8		port_enable_cb_idx;
 	u8		config_cb_idx;
 	u8		tm_tr_cb_idx;
 	u8		tm_tr_volume_cb_idx;
 	u8		tm_sas_control_cb_idx;
 	struct _internal_cmd base_cmds;
+	struct _internal_cmd port_enable_cmds;
 	struct _internal_cmd transport_cmds;
 	struct _internal_cmd scsih_cmds;
 	struct _internal_cmd tm_cmds;
@@ -1001,6 +1013,8 @@ void mpt2sas_base_release_callback_handler(u8 cb_idx);
 
 u8 mpt2sas_base_done(struct MPT2SAS_ADAPTER *ioc, u16 smid, u8 msix_index,
     u32 reply);
+u8 mpt2sas_port_enable_done(struct MPT2SAS_ADAPTER *ioc, u16 smid,
+	u8 msix_index,	u32 reply);
 void *mpt2sas_base_get_reply_virt_addr(struct MPT2SAS_ADAPTER *ioc, u32 phys_addr);
 
 u32 mpt2sas_base_get_iocstate(struct MPT2SAS_ADAPTER *ioc, int cooked);
@@ -1015,6 +1029,8 @@ void mpt2sas_base_validate_event_type(struct MPT2SAS_ADAPTER *ioc, u32 *event_ty
 
 void mpt2sas_halt_firmware(struct MPT2SAS_ADAPTER *ioc);
 
+int mpt2sas_port_enable(struct MPT2SAS_ADAPTER *ioc);
+
 /* scsih shared API */
 u8 mpt2sas_scsih_event_callback(struct MPT2SAS_ADAPTER *ioc, u8 msix_index,
     u32 reply);
@@ -1032,6 +1048,8 @@ struct _sas_node *mpt2sas_scsih_expander_find_by_sas_address(struct MPT2SAS_ADAP
 struct _sas_device *mpt2sas_scsih_sas_device_find_by_sas_address(
     struct MPT2SAS_ADAPTER *ioc, u64 sas_address);
 
+void mpt2sas_port_enable_complete(struct MPT2SAS_ADAPTER *ioc);
+
 void mpt2sas_scsih_reset_handler(struct MPT2SAS_ADAPTER *ioc, int reset_phase);
 
 /* config shared API */