usb: tegra: Use regulators instead of GPIOs for USB PHY VBUS

The tegra ehci driver has enabled USB vbus regulators directly using
GPIOs and the device tree attribute nvidia,vbus-gpio. This is ugly
and causes error messages on boot when both the regulator driver
and the ehci driver want access to the same GPIO.

After this patch, usb vbus regulators for tegra usb phy devices are specified
with the device tree attribute vbus-supply = <&x> where x is a regulator defined
in the device tree. The old nvidia,vbus-gpio property is no longer supported.

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

1 files changed, 1 insertions, 33 deletions

diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c
index 6ee7ef7..14c1f35 100644
--- a/drivers/usb/host/ehci-tegra.c
+++ b/drivers/usb/host/ehci-tegra.c
@@ -322,33 +322,6 @@ static void tegra_ehci_unmap_urb_for_dma(struct usb_hcd *hcd, struct urb *urb)
 	free_dma_aligned_buffer(urb);
 }
 
-static int setup_vbus_gpio(struct platform_device *pdev,
-			   struct tegra_ehci_platform_data *pdata)
-{
-	int err = 0;
-	int gpio;
-
-	gpio = pdata->vbus_gpio;
-	if (!gpio_is_valid(gpio))
-		gpio = of_get_named_gpio(pdev->dev.of_node,
-					 "nvidia,vbus-gpio", 0);
-	if (!gpio_is_valid(gpio))
-		return 0;
-
-	err = gpio_request(gpio, "vbus_gpio");
-	if (err) {
-		dev_err(&pdev->dev, "can't request vbus gpio %d", gpio);
-		return err;
-	}
-	err = gpio_direction_output(gpio, 1);
-	if (err) {
-		dev_err(&pdev->dev, "can't enable vbus\n");
-		return err;
-	}
-
-	return err;
-}
-
 static int tegra_ehci_probe(struct platform_device *pdev)
 {
 	struct resource *res;
@@ -376,14 +349,11 @@ static int tegra_ehci_probe(struct platform_device *pdev)
 	if (!pdev->dev.coherent_dma_mask)
 		pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
 
-	setup_vbus_gpio(pdev, pdata);
-
 	hcd = usb_create_hcd(&tegra_ehci_hc_driver, &pdev->dev,
 					dev_name(&pdev->dev));
 	if (!hcd) {
 		dev_err(&pdev->dev, "Unable to create HCD\n");
-		err = -ENOMEM;
-		goto cleanup_vbus_gpio;
+		return -ENOMEM;
 	}
 	platform_set_drvdata(pdev, hcd);
 	ehci = hcd_to_ehci(hcd);
@@ -494,8 +464,6 @@ cleanup_clk_get:
 	clk_put(tegra->clk);
 cleanup_hcd_create:
 	usb_put_hcd(hcd);
-cleanup_vbus_gpio:
-	/* FIXME: Undo setup_vbus_gpio() here */
 	return err;
 }