diff options
-rw-r--r-- | Documentation/i386/IO-APIC.txt | 2 | ||||
-rw-r--r-- | arch/x86/kernel/cpu/cpufreq/speedstep-smi.c | 39 | ||||
-rw-r--r-- | arch/x86/kernel/cpu/mtrr/generic.c | 42 | ||||
-rw-r--r-- | arch/x86/kernel/io_delay.c | 8 | ||||
-rw-r--r-- | arch/x86/kernel/mfgpt_32.c | 1 | ||||
-rw-r--r-- | arch/x86/kernel/setup_32.c | 9 | ||||
-rw-r--r-- | arch/x86/kernel/setup_64.c | 2 | ||||
-rw-r--r-- | arch/x86/mm/discontig_32.c | 1 | ||||
-rw-r--r-- | arch/x86/mm/ioremap.c | 6 | ||||
-rw-r--r-- | arch/x86/mm/pageattr.c | 2 | ||||
-rw-r--r-- | include/asm-x86/pgtable.h | 2 |
11 files changed, 70 insertions, 44 deletions
diff --git a/Documentation/i386/IO-APIC.txt b/Documentation/i386/IO-APIC.txt index f951666..30b4c71 100644 --- a/Documentation/i386/IO-APIC.txt +++ b/Documentation/i386/IO-APIC.txt @@ -70,7 +70,7 @@ Every PCI card emits a PCI IRQ, which can be INTA, INTB, INTC or INTD: These INTA-D PCI IRQs are always 'local to the card', their real meaning depends on which slot they are in. If you look at the daisy chaining diagram, -a card in slot4, issuing INTA IRQ, it will end up as a signal on PIRQ2 of +a card in slot4, issuing INTA IRQ, it will end up as a signal on PIRQ4 of the PCI chipset. Most cards issue INTA, this creates optimal distribution between the PIRQ lines. (distributing IRQ sources properly is not a necessity, PCI IRQs can be shared at will, but it's a good for performance diff --git a/arch/x86/kernel/cpu/cpufreq/speedstep-smi.c b/arch/x86/kernel/cpu/cpufreq/speedstep-smi.c index f2b5a62..8a85c93 100644 --- a/arch/x86/kernel/cpu/cpufreq/speedstep-smi.c +++ b/arch/x86/kernel/cpu/cpufreq/speedstep-smi.c @@ -63,7 +63,7 @@ static struct cpufreq_frequency_table speedstep_freqs[] = { */ static int speedstep_smi_ownership (void) { - u32 command, result, magic; + u32 command, result, magic, dummy; u32 function = GET_SPEEDSTEP_OWNER; unsigned char magic_data[] = "Copyright (c) 1999 Intel Corporation"; @@ -73,8 +73,11 @@ static int speedstep_smi_ownership (void) dprintk("trying to obtain ownership with command %x at port %x\n", command, smi_port); __asm__ __volatile__( + "push %%ebp\n" "out %%al, (%%dx)\n" - : "=D" (result) + "pop %%ebp\n" + : "=D" (result), "=a" (dummy), "=b" (dummy), "=c" (dummy), "=d" (dummy), + "=S" (dummy) : "a" (command), "b" (function), "c" (0), "d" (smi_port), "D" (0), "S" (magic) : "memory" @@ -96,7 +99,7 @@ static int speedstep_smi_ownership (void) */ static int speedstep_smi_get_freqs (unsigned int *low, unsigned int *high) { - u32 command, result = 0, edi, high_mhz, low_mhz; + u32 command, result = 0, edi, high_mhz, low_mhz, dummy; u32 state=0; u32 function = GET_SPEEDSTEP_FREQS; @@ -109,10 +112,12 @@ static int speedstep_smi_get_freqs (unsigned int *low, unsigned int *high) dprintk("trying to determine frequencies with command %x at port %x\n", command, smi_port); - __asm__ __volatile__("movl $0, %%edi\n" + __asm__ __volatile__( + "push %%ebp\n" "out %%al, (%%dx)\n" - : "=a" (result), "=b" (high_mhz), "=c" (low_mhz), "=d" (state), "=D" (edi) - : "a" (command), "b" (function), "c" (state), "d" (smi_port), "S" (0) + "pop %%ebp" + : "=a" (result), "=b" (high_mhz), "=c" (low_mhz), "=d" (state), "=D" (edi), "=S" (dummy) + : "a" (command), "b" (function), "c" (state), "d" (smi_port), "S" (0), "D" (0) ); dprintk("result %x, low_freq %u, high_freq %u\n", result, low_mhz, high_mhz); @@ -135,16 +140,18 @@ static int speedstep_smi_get_freqs (unsigned int *low, unsigned int *high) static int speedstep_get_state (void) { u32 function=GET_SPEEDSTEP_STATE; - u32 result, state, edi, command; + u32 result, state, edi, command, dummy; command = (smi_sig & 0xffffff00) | (smi_cmd & 0xff); dprintk("trying to determine current setting with command %x at port %x\n", command, smi_port); - __asm__ __volatile__("movl $0, %%edi\n" + __asm__ __volatile__( + "push %%ebp\n" "out %%al, (%%dx)\n" - : "=a" (result), "=b" (state), "=D" (edi) - : "a" (command), "b" (function), "c" (0), "d" (smi_port), "S" (0) + "pop %%ebp\n" + : "=a" (result), "=b" (state), "=D" (edi), "=c" (dummy), "=d" (dummy), "=S" (dummy) + : "a" (command), "b" (function), "c" (0), "d" (smi_port), "S" (0), "D" (0) ); dprintk("state is %x, result is %x\n", state, result); @@ -160,7 +167,7 @@ static int speedstep_get_state (void) */ static void speedstep_set_state (unsigned int state) { - unsigned int result = 0, command, new_state; + unsigned int result = 0, command, new_state, dummy; unsigned long flags; unsigned int function=SET_SPEEDSTEP_STATE; unsigned int retry = 0; @@ -182,10 +189,12 @@ static void speedstep_set_state (unsigned int state) } retry++; __asm__ __volatile__( - "movl $0, %%edi\n" + "push %%ebp\n" "out %%al, (%%dx)\n" - : "=b" (new_state), "=D" (result) - : "a" (command), "b" (function), "c" (state), "d" (smi_port), "S" (0) + "pop %%ebp" + : "=b" (new_state), "=D" (result), "=c" (dummy), "=a" (dummy), + "=d" (dummy), "=S" (dummy) + : "a" (command), "b" (function), "c" (state), "d" (smi_port), "S" (0), "D" (0) ); } while ((new_state != state) && (retry <= SMI_TRIES)); @@ -195,7 +204,7 @@ static void speedstep_set_state (unsigned int state) if (new_state == state) { dprintk("change to %u MHz succeeded after %u tries with result %u\n", (speedstep_freqs[new_state].frequency / 1000), retry, result); } else { - printk(KERN_ERR "cpufreq: change failed with new_state %u and result %u\n", new_state, result); + printk(KERN_ERR "cpufreq: change to state %u failed with new_state %u and result %u\n", state, new_state, result); } return; diff --git a/arch/x86/kernel/cpu/mtrr/generic.c b/arch/x86/kernel/cpu/mtrr/generic.c index 103d61a..3e18db4 100644 --- a/arch/x86/kernel/cpu/mtrr/generic.c +++ b/arch/x86/kernel/cpu/mtrr/generic.c @@ -176,12 +176,13 @@ static inline void k8_enable_fixed_iorrs(void) } /** - * Checks and updates an fixed-range MTRR if it differs from the value it - * should have. If K8 extentions are wanted, update the K8 SYSCFG MSR also. - * see AMD publication no. 24593, chapter 7.8.1, page 233 for more information - * \param msr MSR address of the MTTR which should be checked and updated - * \param changed pointer which indicates whether the MTRR needed to be changed - * \param msrwords pointer to the MSR values which the MSR should have + * set_fixed_range - checks & updates a fixed-range MTRR if it differs from the value it should have + * @msr: MSR address of the MTTR which should be checked and updated + * @changed: pointer which indicates whether the MTRR needed to be changed + * @msrwords: pointer to the MSR values which the MSR should have + * + * If K8 extentions are wanted, update the K8 SYSCFG MSR also. + * See AMD publication no. 24593, chapter 7.8.1, page 233 for more information. */ static void set_fixed_range(int msr, bool *changed, unsigned int *msrwords) { @@ -199,12 +200,15 @@ static void set_fixed_range(int msr, bool *changed, unsigned int *msrwords) } } +/** + * generic_get_free_region - Get a free MTRR. + * @base: The starting (base) address of the region. + * @size: The size (in bytes) of the region. + * @replace_reg: mtrr index to be replaced; set to invalid value if none. + * + * Returns: The index of the region on success, else negative on error. + */ int generic_get_free_region(unsigned long base, unsigned long size, int replace_reg) -/* [SUMMARY] Get a free MTRR. - <base> The starting (base) address of the region. - <size> The size (in bytes) of the region. - [RETURNS] The index of the region on success, else -1 on error. -*/ { int i, max; mtrr_type ltype; @@ -249,8 +253,8 @@ static void generic_get_mtrr(unsigned int reg, unsigned long *base, } /** - * Checks and updates the fixed-range MTRRs if they differ from the saved set - * \param frs pointer to fixed-range MTRR values, saved by get_fixed_ranges() + * set_fixed_ranges - checks & updates the fixed-range MTRRs if they differ from the saved set + * @frs: pointer to fixed-range MTRR values, saved by get_fixed_ranges() */ static int set_fixed_ranges(mtrr_type * frs) { @@ -294,13 +298,13 @@ static bool set_mtrr_var_ranges(unsigned int index, struct mtrr_var_range *vr) static u32 deftype_lo, deftype_hi; +/** + * set_mtrr_state - Set the MTRR state for this CPU. + * + * NOTE: The CPU must already be in a safe state for MTRR changes. + * RETURNS: 0 if no changes made, else a mask indicating what was changed. + */ static unsigned long set_mtrr_state(void) -/* [SUMMARY] Set the MTRR state for this CPU. - <state> The MTRR state information to read. - <ctxt> Some relevant CPU context. - [NOTE] The CPU must already be in a safe state for MTRR changes. - [RETURNS] 0 if no changes made, else a mask indication what was changed. -*/ { unsigned int i; unsigned long change_mask = 0; diff --git a/arch/x86/kernel/io_delay.c b/arch/x86/kernel/io_delay.c index c706a30..5921e5f 100644 --- a/arch/x86/kernel/io_delay.c +++ b/arch/x86/kernel/io_delay.c @@ -78,6 +78,14 @@ static struct dmi_system_id __initdata io_delay_0xed_port_dmi_table[] = { }, { .callback = dmi_io_delay_0xed_port, + .ident = "HP Pavilion dv6000", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "Quanta"), + DMI_MATCH(DMI_BOARD_NAME, "30B8") + } + }, + { + .callback = dmi_io_delay_0xed_port, .ident = "HP Pavilion tx1000", .matches = { DMI_MATCH(DMI_BOARD_VENDOR, "Quanta"), diff --git a/arch/x86/kernel/mfgpt_32.c b/arch/x86/kernel/mfgpt_32.c index 027fc06..b402c0f 100644 --- a/arch/x86/kernel/mfgpt_32.c +++ b/arch/x86/kernel/mfgpt_32.c @@ -30,6 +30,7 @@ #include <linux/kernel.h> #include <linux/interrupt.h> +#include <linux/module.h> #include <asm/geode.h> static struct mfgpt_timer_t { diff --git a/arch/x86/kernel/setup_32.c b/arch/x86/kernel/setup_32.c index a1d7071..2b3e5d4 100644 --- a/arch/x86/kernel/setup_32.c +++ b/arch/x86/kernel/setup_32.c @@ -406,8 +406,6 @@ static unsigned long __init setup_memory(void) */ min_low_pfn = PFN_UP(init_pg_tables_end); - find_max_pfn(); - max_low_pfn = find_max_low_pfn(); #ifdef CONFIG_HIGHMEM @@ -764,12 +762,13 @@ void __init setup_arch(char **cmdline_p) if (efi_enabled) efi_init(); - max_low_pfn = setup_memory(); - /* update e820 for memory not covered by WB MTRRs */ + find_max_pfn(); mtrr_bp_init(); if (mtrr_trim_uncached_memory(max_pfn)) - max_low_pfn = setup_memory(); + find_max_pfn(); + + max_low_pfn = setup_memory(); #ifdef CONFIG_VMI /* diff --git a/arch/x86/kernel/setup_64.c b/arch/x86/kernel/setup_64.c index 7637dc9..f4f7ecf 100644 --- a/arch/x86/kernel/setup_64.c +++ b/arch/x86/kernel/setup_64.c @@ -801,7 +801,7 @@ static void __cpuinit srat_detect_node(void) /* Don't do the funky fallback heuristics the AMD version employs for now. */ node = apicid_to_node[apicid]; - if (node == NUMA_NO_NODE) + if (node == NUMA_NO_NODE || !node_online(node)) node = first_node(node_online_map); numa_set_node(cpu, node); diff --git a/arch/x86/mm/discontig_32.c b/arch/x86/mm/discontig_32.c index c394ca0..8e25e06 100644 --- a/arch/x86/mm/discontig_32.c +++ b/arch/x86/mm/discontig_32.c @@ -324,7 +324,6 @@ unsigned long __init setup_memory(void) * this space and use it to adjust the boundary between ZONE_NORMAL * and ZONE_HIGHMEM. */ - find_max_pfn(); get_memcfg_numa(); kva_pages = calculate_numa_remap_pages(); diff --git a/arch/x86/mm/ioremap.c b/arch/x86/mm/ioremap.c index 4afaba0..794895c 100644 --- a/arch/x86/mm/ioremap.c +++ b/arch/x86/mm/ioremap.c @@ -137,7 +137,11 @@ static void __iomem *__ioremap(resource_size_t phys_addr, unsigned long size, switch (mode) { case IOR_MODE_UNCACHED: default: - prot = PAGE_KERNEL_NOCACHE; + /* + * FIXME: we will use UC MINUS for now, as video fb drivers + * depend on it. Upcoming ioremap_wc() will fix this behavior. + */ + prot = PAGE_KERNEL_UC_MINUS; break; case IOR_MODE_CACHED: prot = PAGE_KERNEL; diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c index 14e48b5..7b79f6b 100644 --- a/arch/x86/mm/pageattr.c +++ b/arch/x86/mm/pageattr.c @@ -771,7 +771,7 @@ static inline int change_page_attr_clear(unsigned long addr, int numpages, int set_memory_uc(unsigned long addr, int numpages) { return change_page_attr_set(addr, numpages, - __pgprot(_PAGE_PCD | _PAGE_PWT)); + __pgprot(_PAGE_PCD)); } EXPORT_SYMBOL(set_memory_uc); diff --git a/include/asm-x86/pgtable.h b/include/asm-x86/pgtable.h index 174b877..9cf472a 100644 --- a/include/asm-x86/pgtable.h +++ b/include/asm-x86/pgtable.h @@ -85,6 +85,7 @@ extern pteval_t __PAGE_KERNEL, __PAGE_KERNEL_EXEC; #define __PAGE_KERNEL_RX (__PAGE_KERNEL_EXEC & ~_PAGE_RW) #define __PAGE_KERNEL_EXEC_NOCACHE (__PAGE_KERNEL_EXEC | _PAGE_PCD | _PAGE_PWT) #define __PAGE_KERNEL_NOCACHE (__PAGE_KERNEL | _PAGE_PCD | _PAGE_PWT) +#define __PAGE_KERNEL_UC_MINUS (__PAGE_KERNEL | _PAGE_PCD) #define __PAGE_KERNEL_VSYSCALL (__PAGE_KERNEL_RX | _PAGE_USER) #define __PAGE_KERNEL_VSYSCALL_NOCACHE (__PAGE_KERNEL_VSYSCALL | _PAGE_PCD | _PAGE_PWT) #define __PAGE_KERNEL_LARGE (__PAGE_KERNEL | _PAGE_PSE) @@ -101,6 +102,7 @@ extern pteval_t __PAGE_KERNEL, __PAGE_KERNEL_EXEC; #define PAGE_KERNEL_EXEC MAKE_GLOBAL(__PAGE_KERNEL_EXEC) #define PAGE_KERNEL_RX MAKE_GLOBAL(__PAGE_KERNEL_RX) #define PAGE_KERNEL_NOCACHE MAKE_GLOBAL(__PAGE_KERNEL_NOCACHE) +#define PAGE_KERNEL_UC_MINUS MAKE_GLOBAL(__PAGE_KERNEL_UC_MINUS) #define PAGE_KERNEL_EXEC_NOCACHE MAKE_GLOBAL(__PAGE_KERNEL_EXEC_NOCACHE) #define PAGE_KERNEL_LARGE MAKE_GLOBAL(__PAGE_KERNEL_LARGE) #define PAGE_KERNEL_LARGE_EXEC MAKE_GLOBAL(__PAGE_KERNEL_LARGE_EXEC) |