diff options
Diffstat (limited to 'Documentation/devicetree')
14 files changed, 554 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt new file mode 100644 index 0000000..e37241f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -0,0 +1,51 @@ +* Texas Instruments Davinci NAND + +This file provides information, what the device node for the +davinci nand interface contain. + +Required properties: +- compatible: "ti,davinci-nand"; +- reg : contain 2 offset/length values: + - offset and length for the access window + - offset and length for accessing the aemif control registers +- ti,davinci-chipselect: Indicates on the davinci_nand driver which + chipselect is used for accessing the nand. + +Recommended properties : +- ti,davinci-mask-ale: mask for ale +- ti,davinci-mask-cle: mask for cle +- ti,davinci-mask-chipsel: mask for chipselect +- ti,davinci-ecc-mode: ECC mode valid values for davinci driver: + - "none" + - "soft" + - "hw" +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4. +- ti,davinci-nand-buswidth: buswidth 8 or 16 +- ti,davinci-nand-use-bbt: use flash based bad block table support. + +Example (enbw_cmc board): +aemif@60000000 { + compatible = "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x68000000 0x80000>; + ranges = <2 0 0x60000000 0x02000000 + 3 0 0x62000000 0x02000000 + 4 0 0x64000000 0x02000000 + 5 0 0x66000000 0x02000000 + 6 0 0x68000000 0x02000000>; + nand@3,0 { + compatible = "ti,davinci-nand"; + reg = <3 0x0 0x807ff + 6 0x0 0x8000>; + #address-cells = <1>; + #size-cells = <1>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt new file mode 100644 index 0000000..0a85c70 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt @@ -0,0 +1,68 @@ +* Atmel High Speed MultiMedia Card Interface + +This controller on atmel products provides an interface for MMC, SD and SDIO +types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the atmel-mci driver. + +1) MCI node + +Required properties: +- compatible: should be "atmel,hsmci" +- #address-cells: should be one. The cell is the slot id. +- #size-cells: should be zero. +- at least one slot node + +The node contains child nodes for each slot that the platform uses + +Example MCI node: + +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + + [ child node definitions...] +}; + +2) slot nodes + +Required properties: +- reg: should contain the slot id. +- bus-width: number of data lines connected to the controller + +Optional properties: +- cd-gpios: specify GPIOs for card detection +- cd-inverted: invert the value of external card detect gpio line +- wp-gpios: specify GPIOs for write protection + +Example slot node: + +slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; +}; + +Example full MCI node: +mmc0: mmc@f0008000 { + compatible = "atmel,hsmci"; + reg = <0xf0008000 0x600>; + interrupts = <12 4>; + #address-cells = <1>; + #size-cells = <0>; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioD 15 0> + cd-inverted; + }; + slot@1 { + reg = <1>; + bus-width = <4>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt new file mode 100644 index 0000000..7927689 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -0,0 +1,87 @@ +* Samsung Exynos specific extensions to the Synopsis Designware Mobile + Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsis dw mshc controller properties described +by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific +extensions to the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210 + specific extentions. + - "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412 + specific extentions. + - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250 + specific extentions. + +* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface + unit (ciu) clock. This property is applicable only for Exynos5 SoC's and + ignored for Exynos4 SoC's. The valid range of divider value is 0 to 7. + +* samsung,dw-mshc-sdr-timing: Specifies the value of CIU clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for single + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + +* samsung,dw-mshc-ddr-timing: Specifies the value of CUI clock phase shift value + in transmit mode and CIU clock phase shift value in receive mode for double + data rate mode operation. Refer notes below for the order of the cells and the + valid values. + + Notes for the sdr-timing and ddr-timing values: + + The order of the cells should be + - First Cell: CIU clock phase shift value for tx mode. + - Second Cell: CIU clock phase shift value for rx mode. + + Valid values for SDR and DDR CIU clock timing for Exynos5250: + - valid value for tx phase shift and rx phase shift is 0 to 7. + - when CIU clock divider value is set to 3, all possible 8 phase shift + values can be used. + - if CIU clock divider value is 0 (that is divide by 1), both tx and rx + phase shift clocks should be 0. + +Required properties for a slot: + +* gpios: specifies a list of gpios used for command, clock and data bus. The + first gpio is the command line and the second gpio is the clock line. The + rest of the gpios (depending on the bus-width property) are the data lines in + no particular order. The format of the gpio specifier depends on the gpio + controller. + +Example: + + The MSHC controller node can be split into two portions, SoC specific and + board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + + slot@0 { + reg = <0>; + bus-width = <8>; + gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>, + <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>, + <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>, + <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>, + <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8a6811f..8e2e0ba 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -9,12 +9,17 @@ Interpreted by the OF core: Required properties: - bus-width: Number of data lines, can be <1>, <4>, or <8> +Card detection: +If no property below is supplied, standard SDHCI card detect is used. +Only one of the properties in this section should be supplied: + - broken-cd: There is no card detection available; polling must be used. + - cd-gpios: Specify GPIOs for card detection, see gpio binding + - non-removable: non-removable slot (like eMMC); assume always present. + Optional properties: -- cd-gpios: Specify GPIOs for card detection, see gpio binding - wp-gpios: Specify GPIOs for write protection, see gpio binding - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted -- non-removable: non-removable slot (like eMMC) - max-frequency: maximum operating clock frequency Example: diff --git a/Documentation/devicetree/bindings/mmc/pxa-mmc.txt b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt new file mode 100644 index 0000000..b7025de --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/pxa-mmc.txt @@ -0,0 +1,25 @@ +* PXA MMC drivers + +Driver bindings for the PXA MCI (MMC/SDIO) interfaces + +Required properties: +- compatible: Should be "marvell,pxa-mmc". +- vmmc-supply: A regulator for VMMC + +Optional properties: +- marvell,detect-delay-ms: sets the detection delay timeout in ms. +- marvell,gpio-power: GPIO spec for the card power enable pin + +This file documents differences between the core properties in mmc.txt +and the properties used by the pxa-mmc driver. + +Examples: + +mmc0: mmc@41100000 { + compatible = "marvell,pxa-mmc"; + reg = <0x41100000 0x1000>; + interrupts = <23>; + cd-gpios = <&gpio 23 0>; + wp-gpios = <&gpio 24 0>; +}; + diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt new file mode 100644 index 0000000..630a7d7 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -0,0 +1,53 @@ +* Samsung's SDHCI Controller device tree bindings + +Samsung's SDHCI controller is used as a connectivity interface with external +MMC, SD and eMMC storage mediums. This file documents differences between the +core mmc properties described by mmc.txt and the properties used by the +Samsung implmentation of the SDHCI controller. + +Note: The mmc core bindings documentation states that if none of the core +card-detect bindings are used, then the standard sdhci card detect mechanism +is used. The Samsung's SDHCI controller bindings extends this as listed below. + +[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the + "Optional Board Specific Properties" section below. + +[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property + is not specified, it is assumed that there is no card detection + mechanism used. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci + controller. + - "samsung,exynos4210-sdhci": For controllers compatible with Exynos4 sdhci + controller. + +Required Board Specific Properties: +- gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. + +Optional Board Specific Properties: +- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed + through a pinmux to the card-detect pin of the card slot. This property + should be used only if none of the mmc core card-detect properties are + used. + +Example: + sdhci@12530000 { + compatible = "samsung,exynos4210-sdhci"; + reg = <0x12530000 0x100>; + interrupts = <0 75 0>; + bus-width = <4>; + cd-gpios = <&gpk2 2 2 3 3>; + gpios = <&gpk2 0 2 0 3>, /* clock line */ + <&gpk2 1 2 0 3>, /* command line */ + <&gpk2 3 2 3 3>, /* data line 0 */ + <&gpk2 4 2 3 3>, /* data line 1 */ + <&gpk2 5 2 3 3>, /* data line 2 */ + <&gpk2 6 2 3 3>; /* data line 3 */ + }; + + Note: This example shows both SoC specific and board specific properties + in a single device node. The properties can be actually be seperated + into SoC specific node and board specific node. diff --git a/Documentation/devicetree/bindings/mmc/sdhci-dove.txt b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt new file mode 100644 index 0000000..ae9aab9 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-dove.txt @@ -0,0 +1,14 @@ +* Marvell sdhci-dove controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-pxav2 and sdhci-pxav3 drivers. + +- compatible: Should be "marvell,dove-sdhci". + +Example: + +sdio0: sdio@92000 { + compatible = "marvell,dove-sdhci"; + reg = <0x92000 0x100>; + interrupts = <35>; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-spear.txt b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt new file mode 100644 index 0000000..fd3643e --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-spear.txt @@ -0,0 +1,18 @@ +* SPEAr SDHCI Controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci-spear driver. + +Required properties: +- compatible: "st,spear300-sdhci" + +Optional properties: +- cd-gpios: card detect gpio, with zero flags. + +Example: + + sdhci@fc000000 { + compatible = "st,spear300-sdhci"; + reg = <0xfc000000 0x1000>; + cd-gpios = <&gpio0 6 0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt new file mode 100644 index 0000000..06cd32d08 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt @@ -0,0 +1,79 @@ +* Synopsis Designware Mobile Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core mmc properties described by mmc.txt and the +properties used by the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - snps,dw-mshc: for controllers compliant with synopsis dw-mshc. +* #address-cells: should be 1. +* #size-cells: should be 0. + +# Slots: The slot specific information are contained within child-nodes with + each child-node representing a supported slot. There should be atleast one + child node representing a card slot. The name of the child node representing + the slot is recommended to be slot@n where n is the unique number of the slot + connnected to the controller. The following are optional properties which + can be included in the slot child node. + + * reg: specifies the physical slot number. The valid values of this + property is 0 to (num-slots -1), where num-slots is the value + specified by the num-slots property. + + * bus-width: as documented in mmc core bindings. + + * wp-gpios: specifies the write protect gpio line. The format of the + gpio specifier depends on the gpio controller. If the write-protect + line is not available, this property is optional. + +Optional properties: + +* num-slots: specifies the number of slots supported by the controller. + The number of physical slots actually used could be equal or less than the + value specified by num-slots. If this property is not specified, the value + of num-slot property is assumed to be 1. + +* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not + specified, the default value of the fifo size is determined from the + controller registers. + +* card-detect-delay: Delay in milli-seconds before detecting card after card + insert event. The default value is 0. + +* supports-highspeed: Enables support for high speed cards (upto 50MHz) + +* broken-cd: as documented in mmc core bindings. + +Aliases: + +- All the MSHC controller nodes should be represented in the aliases node using + the following format 'mshc{n}' where n is a unique number for the alias. + +Example: + +The MSHC controller node can be split into two portions, SoC specific and +board specific portions as listed below. + + dwmmc0@12200000 { + compatible = "snps,dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + dwmmc0@12200000 { + num-slots = <1>; + supports-highspeed; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + + slot@0 { + reg = <0>; + bus-width = <8>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index a200695..d555421 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -3,7 +3,9 @@ Atmel NAND flash Required properties: - compatible : "atmel,at91rm9200-nand". - reg : should specify localbus address and size used for the chip, - and if availlable the ECC. + and hardware ECC controller if available. + If the hardware ECC is PMECC, it should contain address and size for + PMECC, PMECC Error Location controller and ROM which has lookup tables. - atmel,nand-addr-offset : offset for the address latch. - atmel,nand-cmd-offset : offset for the command latch. - #address-cells, #size-cells : Must be present if the device has sub-nodes @@ -16,6 +18,15 @@ Optional properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". +- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware. + Only supported by at91sam9x5 or later sam9 product. +- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC + Controller. Supported values are: 2, 4, 8, 12, 24. +- atmel,pmecc-sector-size : sector size for ECC computation. Supported values + are: 512, 1024. +- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM + for different sector size. First one is for sector size 512, the next is for + sector size 1024. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false @@ -39,3 +50,30 @@ nand0: nand@40000000,0 { ... }; }; + +/* for PMECC supported chips */ +nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = < 0x40000000 0x10000000 /* bus addr & size */ + 0xffffe000 0x00000600 /* PMECC addr & size */ + 0xffffe600 0x00000200 /* PMECC ERRLOC addr & size */ + 0x00100000 0x00100000 /* ROM addr & size */ + >; + atmel,nand-addr-offset = <21>; /* ale */ + atmel,nand-cmd-offset = <22>; /* cle */ + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + atmel,has-pmecc; /* enable PMECC */ + atmel,pmecc-cap = <2>; + atmel,pmecc-sector-size = <512>; + atmel,pmecc-lookup-table-offset = <0x8000 0x10000>; + gpios = <&pioD 5 0 /* rdy */ + &pioD 4 0 /* nce */ + 0 /* cd */ + >; + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index 1a5bbd3..3fb3f901 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -12,6 +12,10 @@ Required properties: - interrupt-names : The interrupt names "gpmi-dma", "bch"; - fsl,gpmi-dma-channel : Should contain the dma channel it uses. +Optional properties: + - nand-on-flash-bbt: boolean to enable on flash bbt option if not + present false + The device tree may optionally contain sub-nodes describing partitions of the address space. See partition.txt for more detail. diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt new file mode 100644 index 0000000..d0a3725 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt @@ -0,0 +1,50 @@ +NXP LPC32xx SoC NAND MLC controller + +Required properties: +- compatible: "nxp,lpc3220-mlc" +- reg: Address and size of the controller +- interrupts: The NAND interrupt specification +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in +Hz, to make them independent of actual clock speed and to provide for good +accuracy:) +- nxp,tcea_delay: TCEA_DELAY +- nxp,busy_delay: BUSY_DELAY +- nxp,nand_ta: NAND_TA +- nxp,rd_high: RD_HIGH +- nxp,rd_low: RD_LOW +- nxp,wr_high: WR_HIGH +- nxp,wr_low: WR_LOW + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + + mlc: flash@200A8000 { + compatible = "nxp,lpc3220-mlc"; + reg = <0x200A8000 0x11000>; + interrupts = <11 0>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,tcea-delay = <333333333>; + nxp,busy-delay = <10000000>; + nxp,nand-ta = <18181818>; + nxp,rd-high = <31250000>; + nxp,rd-low = <45454545>; + nxp,wr-high = <40000000>; + nxp,wr-low = <83333333>; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt new file mode 100644 index 0000000..d94edc0 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt @@ -0,0 +1,52 @@ +NXP LPC32xx SoC NAND SLC controller + +Required properties: +- compatible: "nxp,lpc3220-slc" +- reg: Address and size of the controller +- nand-on-flash-bbt: Use bad block table on flash +- gpios: GPIO specification for NAND write protect + +The following required properties are very controller specific. See the LPC32xx +User Manual: +- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY) +- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY) +(The following values are specified in Hz, to make them independent of actual +clock speed:) +- nxp,wwidth: Write pulse width (W_WIDTH) +- nxp,whold: Write hold time (W_HOLD) +- nxp,wsetup: Write setup time (W_SETUP) +- nxp,rwidth: Read pulse width (R_WIDTH) +- nxp,rhold: Read hold time (R_HOLD) +- nxp,rsetup: Read setup time (R_SETUP) + +Optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + + slc: flash@20020000 { + compatible = "nxp,lpc3220-slc"; + reg = <0x20020000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "phy3250-boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + ... + + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index a63c2bd7..94de19b 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -16,6 +16,13 @@ file systems on embedded devices. - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions (see below). In this case both #address-cells and #size-cells must be equal to 1. + - no-unaligned-direct-access: boolean to disable the default direct + mapping of the flash. + On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause + problems with JFFS2 usage, as the local bus (LPB) doesn't support + unaligned accesses as implemented in the JFFS2 code via memcpy(). + By defining "no-unaligned-direct-access", the flash will not be + exposed directly to the MTD users (e.g. JFFS2) any more. For JEDEC compatible devices, the following additional properties are defined: |