diff options
Diffstat (limited to 'drivers/staging/rtl8192u/r8192U_core.c')
-rw-r--r-- | drivers/staging/rtl8192u/r8192U_core.c | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/drivers/staging/rtl8192u/r8192U_core.c b/drivers/staging/rtl8192u/r8192U_core.c index be86045..5981d66 100644 --- a/drivers/staging/rtl8192u/r8192U_core.c +++ b/drivers/staging/rtl8192u/r8192U_core.c @@ -203,7 +203,7 @@ static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv* priv) { Dot11d_Init(ieee); ieee->bGlobalDomain = false; - //actually 8225 & 8256 rf chip only support B,G,24N mode + //actually 8225 & 8256 rf chips only support B,G,24N mode if ((priv->rf_chip == RF_8225) || (priv->rf_chip == RF_8256)) { min_chan = 1; @@ -1476,7 +1476,7 @@ static void rtl8192_tx_isr(struct urb *tx_urb) if(tcb_desc->queue_index != TXCMD_QUEUE) { if(tx_urb->status == 0) { dev->trans_start = jiffies; - // As act as station mode, destination shall be unicast address. + // Act as station mode, destination shall be unicast address. //priv->ieee80211->stats.tx_bytes+=(skb->len - priv->ieee80211->tx_headroom); //priv->ieee80211->stats.tx_packets++; priv->stats.txoktotal++; @@ -1527,8 +1527,8 @@ static void rtl8192_tx_isr(struct urb *tx_urb) * function, it should contain enough tx irq; * 2. check packet type; * 3. initialize sendlist, check whether the to-be send packet no greater than 1 - * 4. aggregates the packets, and fill firmware info and tx desc to it, etc. - * 5. check whether the packet could be sent, otherwise just insert to wait head + * 4. aggregates the packets, and fill firmware info and tx desc into it, etc. + * 5. check whether the packet could be sent, otherwise just insert into wait head * */ skb = skb_dequeue(&priv->ieee80211->skb_drv_aggQ[queue_index]); if(!check_nic_enough_desc(dev, queue_index)) { @@ -2783,7 +2783,7 @@ static void rtl8192_init_priv_variable(struct net_device* dev) (TCR_MXDMA_2048<<TCR_MXDMA_OFFSET)| // Max DMA Burst Size per Tx DMA Burst, 7: reserved. (priv->ShortRetryLimit<<TCR_SRL_OFFSET)| // Short retry limit (priv->LongRetryLimit<<TCR_LRL_OFFSET) | // Long retry limit - (false ? TCR_SAT: 0); // FALSE: HW provides PLCP length and LENGEXT, TURE: SW provides them + (false ? TCR_SAT: 0); // FALSE: HW provides PLCP length and LENGEXT, TRUE: SW provides them #ifdef TO_DO_LIST if(Adapter->bInHctTest) pHalData->ReceiveConfig = pHalData->CSMethod | @@ -3437,7 +3437,7 @@ if(Adapter->ResetProgress == RESET_TYPE_NORESET) { // User disable RF via registry. RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter819xUsb(): Turn off RF for RegRfOff ----------\n")); MgntActSet_RF_State(Adapter, eRfOff, RF_CHANGE_BY_SW); - // Those action will be discard in MgntActSet_RF_State because of the same state + // Those actions will be discard in MgntActSet_RF_State because of the same state for(eRFPath = 0; eRFPath <pHalData->NumTotalRFPath; eRFPath++) PHY_SetRFReg(Adapter, (RF90_RADIO_PATH_E)eRFPath, 0x4, 0xC00, 0x0); } @@ -3458,7 +3458,7 @@ if(Adapter->ResetProgress == RESET_TYPE_NORESET) if(pHalData->eRFPowerState == eRfOff) { MgntActSet_RF_State(Adapter, eRfOff, pMgntInfo->RfOffReason); - // Those action will be discard in MgntActSet_RF_State because of the same state + // Those actions will be discard in MgntActSet_RF_State because of the same state for(eRFPath = 0; eRFPath <pHalData->NumTotalRFPath; eRFPath++) PHY_SetRFReg(Adapter, (RF90_RADIO_PATH_E)eRFPath, 0x4, 0xC00, 0x0); } @@ -4516,7 +4516,7 @@ u8 HwRateToMRate90(bool bIsHT, u8 rate) /** * Function: UpdateRxPktTimeStamp - * Overview: Record down the TSF time stamp when receiving a packet + * Overview: Record the TSF time stamp when receiving a packet * * Input: * PADAPTER Adapter @@ -4558,8 +4558,8 @@ long rtl819x_translate_todbm(u8 signal_strength_index )// 0-100 index. /* 2008/01/22 MH We can not declare RSSI/EVM total value of sliding window to be a local static. Otherwise, it may increase when we return from S3/S4. The - value will be kept in memory or disk. We must declare the value in adapter - and it will be reinitialized when return from S3/S4. */ + value will be kept in memory or disk. Declare the value in the adaptor + and it will be reinitialized when returned from S3/S4. */ void rtl8192_process_phyinfo(struct r8192_priv * priv,u8* buffer, struct ieee80211_rx_stats * pprevious_stats, struct ieee80211_rx_stats * pcurrent_stats) { bool bcheck = false; @@ -5092,7 +5092,7 @@ static void rtl8192_query_rxphystatus( rx_evmX = (char)(tmp_rxevm); // Do not use shift operation like "rx_evmX >>= 1" because the compiler of free build environment - // fill most significant bit to "zero" when doing shifting operation which may change a negative + // will set the most significant bit to "zero" when doing shifting operation which may change a negative // value to positive one, then the dbm value (which is supposed to be negative) is not correct anymore. rx_evmX /= 2; //dbm @@ -5211,7 +5211,7 @@ void TranslateRxSignalStuff819xUsb(struct sk_buff *skb, /** * Function: UpdateReceivedRateHistogramStatistics -* Overview: Record down the received data rate +* Overview: Record the received data rate * * Input: * struct net_device *dev |