diff options
Diffstat (limited to 'drivers/staging/rtl8192u/r8192U_dm.c')
-rw-r--r-- | drivers/staging/rtl8192u/r8192U_dm.c | 16 |
1 files changed, 8 insertions, 8 deletions
diff --git a/drivers/staging/rtl8192u/r8192U_dm.c b/drivers/staging/rtl8192u/r8192U_dm.c index 3f79e61..996e658 100644 --- a/drivers/staging/rtl8192u/r8192U_dm.c +++ b/drivers/staging/rtl8192u/r8192U_dm.c @@ -1457,7 +1457,7 @@ static void dm_InitializeTXPowerTracking_ThermalMeter(struct net_device *dev) { struct r8192_priv *priv = ieee80211_priv(dev); - // Tx Power tracking by Thermal Meter require Firmware R/W 3-wire. This mechanism + // Tx Power tracking by Thermal Meter requires Firmware R/W 3-wire. This mechanism // can be enabled only when Firmware R/W 3-wire is enabled. Otherwise, frequent r/w // 3-wire by driver causes RF to go into a wrong state. if(priv->ieee80211->FwRWRF) @@ -1520,7 +1520,7 @@ static void dm_CheckTXPowerTracking_ThermalMeter(struct net_device *dev) if(!TM_Trigger) { - //Attention!! You have to write all 12bits data to RF, or it may cause RF to crash + //Attention!! You have to write all 12bits of data to RF, or it may cause RF to crash //actually write reg0x02 bit1=0, then bit1=1. //DbgPrint("Trigger ThermalMeter, write RF reg0x2 = 0x4d to 0x4f\n"); rtl8192_phy_SetRFReg(dev, RF90_PATH_A, 0x02, bMask12Bits, 0x4d); @@ -2161,7 +2161,7 @@ static void dm_ctrl_initgain_byrssi_by_fwfalse_alarm( pHalData->UndecoratedSmoothedPWDB, DM_DigTable.RssiLowThresh, DM_DigTable.RssiHighThresh, DM_DigTable.Dig_State);*/ /* 1. When RSSI decrease, We have to judge if it is smaller than a threshold - and then execute below step. */ + and then execute the step below. */ if ((priv->undecorated_smoothed_pwdb <= dm_digtable.rssi_low_thresh)) { /* 2008/02/05 MH When we execute silent reset, the DIG PHY parameters @@ -2221,7 +2221,7 @@ static void dm_ctrl_initgain_byrssi_by_fwfalse_alarm( } /* 2. When RSSI increase, We have to judge if it is larger than a threshold - and then execute below step. */ + and then execute the step below. */ if ((priv->undecorated_smoothed_pwdb >= dm_digtable.rssi_high_thresh) ) { u8 reset_flag = 0; @@ -2329,7 +2329,7 @@ static void dm_ctrl_initgain_byrssi_highpwr( } /* 3. When RSSI >75% or <70%, it is a high power issue. We have to judge if - it is larger than a threshold and then execute below step. */ + it is larger than a threshold and then execute the step below. */ // 2008/02/05 MH SD3-Jerry Modify PD_TH for high power issue. if (priv->undecorated_smoothed_pwdb >= dm_digtable.rssi_high_power_highthresh) { @@ -2842,7 +2842,7 @@ static void dm_check_rfctrl_gpio(struct net_device * dev) //struct r8192_priv *priv = ieee80211_priv(dev); // Work around for DTM test, we will not enable HW - radio on/off because r/w - // page 1 register before extra bus is enabled causing system fails when resuming + // page 1 register before extra bus is enabled causing system failures when resuming // from S4. 20080218, Emily // Stop to execute workitem to prevent S3/S4 bug. @@ -3392,7 +3392,7 @@ extern void dm_fsync_timer_callback(unsigned long data) } else { - // Stop continue count + // Stop the continued count priv->ContiuneDiffCount = 0; } @@ -3523,7 +3523,7 @@ static void dm_StartSWFsync(struct net_device *dev) RT_TRACE(COMP_HALDM,"%s\n", __FUNCTION__); // Initial rate record to zero, start to record. priv->rate_record = 0; - // Initial continue diff count to zero, start to record. + // Initialize continue diff count to zero, start to record. priv->ContiuneDiffCount = 0; priv->rateCountDiffRecord = 0; priv->bswitch_fsync = false; |