diff options
Diffstat (limited to 'drivers/thermal/samsung/exynos_tmu.h')
| -rw-r--r-- | drivers/thermal/samsung/exynos_tmu.h | 49 |
1 files changed, 31 insertions, 18 deletions
diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index 1857609..473acae 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -32,6 +32,11 @@ enum calibration_type { TYPE_NONE, }; +enum calibration_mode { + SW_MODE, + HW_MODE, +}; + enum soc_type { SOC_ARCH_EXYNOS4210 = 1, SOC_ARCH_EXYNOS, @@ -57,18 +62,15 @@ enum soc_type { * 3: temperature for trigger_level3 interrupt * condition for trigger_level3 interrupt: * current temperature > threshold + trigger_levels[3] - * @trigger_level0_en: - * 1 = enable trigger_level0 interrupt, - * 0 = disable trigger_level0 interrupt - * @trigger_level1_en: - * 1 = enable trigger_level1 interrupt, - * 0 = disable trigger_level1 interrupt - * @trigger_level2_en: - * 1 = enable trigger_level2 interrupt, - * 0 = disable trigger_level2 interrupt - * @trigger_level3_en: - * 1 = enable trigger_level3 interrupt, - * 0 = disable trigger_level3 interrupt + * @trigger_type: defines the type of trigger. Possible values are, + * THROTTLE_ACTIVE trigger type + * THROTTLE_PASSIVE trigger type + * SW_TRIP trigger type + * HW_TRIP + * @trigger_enable[]: array to denote which trigger levels are enabled. + * 1 = enable trigger_level[] interrupt, + * 0 = disable trigger_level[] interrupt + * @max_trigger_level: max trigger level supported by the TMU * @gain: gain of amplifier in the positive-TC generator block * 0 <= gain <= 15 * @reference_voltage: reference voltage of amplifier @@ -78,7 +80,13 @@ enum soc_type { * 000, 100, 101, 110 and 111 can be different modes * @type: determines the type of SOC * @efuse_value: platform defined fuse value + * @min_efuse_value: minimum valid trimming data + * @max_efuse_value: maximum valid trimming data + * @first_point_trim: temp value of the first point trimming + * @second_point_trim: temp value of the second point trimming + * @default_temp_offset: default temperature offset in case of no trimming * @cal_type: calibration type for temperature + * @cal_mode: calibration mode for temperature * @freq_clip_table: Table representing frequency reduction percentage. * @freq_tab_count: Count of the above table as frequency reduction may * applicable to only some of the trigger levels. @@ -88,18 +96,23 @@ enum soc_type { struct exynos_tmu_platform_data { u8 threshold; u8 threshold_falling; - u8 trigger_levels[4]; - bool trigger_level0_en; - bool trigger_level1_en; - bool trigger_level2_en; - bool trigger_level3_en; - + u8 trigger_levels[MAX_TRIP_COUNT]; + enum trigger_type trigger_type[MAX_TRIP_COUNT]; + bool trigger_enable[MAX_TRIP_COUNT]; + u8 max_trigger_level; u8 gain; u8 reference_voltage; u8 noise_cancel_mode; + u32 efuse_value; + u32 min_efuse_value; + u32 max_efuse_value; + u8 first_point_trim; + u8 second_point_trim; + u8 default_temp_offset; enum calibration_type cal_type; + enum calibration_mode cal_mode; enum soc_type type; struct freq_clip_table freq_tab[4]; unsigned int freq_tab_count; |