diff options
Diffstat (limited to 'drivers/tty/serial/ucc_uart.c')
-rw-r--r-- | drivers/tty/serial/ucc_uart.c | 178 |
1 files changed, 91 insertions, 87 deletions
diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c index 8831748..2c9a87c 100644 --- a/drivers/tty/serial/ucc_uart.c +++ b/drivers/tty/serial/ucc_uart.c @@ -26,13 +26,13 @@ #include <linux/tty_flip.h> #include <linux/io.h> #include <linux/of_platform.h> +#include <linux/of_irq.h> #include <linux/dma-mapping.h> #include <linux/fs_uart_pd.h> -#include <asm/ucc_slow.h> +#include <linux/fsl/ucc_slow.h> #include <linux/firmware.h> -#include <asm/reg.h> /* * The GUMR flag for Soft UART. This would normally be defined in qe.h, @@ -257,11 +257,11 @@ static unsigned int qe_uart_tx_empty(struct uart_port *port) struct qe_bd *bdp = qe_port->tx_bd_base; while (1) { - if (in_be16(&bdp->status) & BD_SC_READY) + if (ioread16be(&bdp->status) & BD_SC_READY) /* This BD is not done, so return "not done" */ return 0; - if (in_be16(&bdp->status) & BD_SC_WRAP) + if (ioread16be(&bdp->status) & BD_SC_WRAP) /* * This BD is done and it's the last one, so return * "done" @@ -339,13 +339,13 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port) /* Pick next descriptor and fill from buffer */ bdp = qe_port->tx_cur; - p = qe2cpu_addr(bdp->buf, qe_port); + p = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port); *p++ = port->x_char; - out_be16(&bdp->length, 1); + iowrite16be(1, &bdp->length); setbits16(&bdp->status, BD_SC_READY); /* Get next BD. */ - if (in_be16(&bdp->status) & BD_SC_WRAP) + if (ioread16be(&bdp->status) & BD_SC_WRAP) bdp = qe_port->tx_bd_base; else bdp++; @@ -364,10 +364,10 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port) /* Pick next descriptor and fill from buffer */ bdp = qe_port->tx_cur; - while (!(in_be16(&bdp->status) & BD_SC_READY) && + while (!(ioread16be(&bdp->status) & BD_SC_READY) && (xmit->tail != xmit->head)) { count = 0; - p = qe2cpu_addr(bdp->buf, qe_port); + p = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port); while (count < qe_port->tx_fifosize) { *p++ = xmit->buf[xmit->tail]; xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); @@ -377,11 +377,11 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port) break; } - out_be16(&bdp->length, count); + iowrite16be(count, &bdp->length); setbits16(&bdp->status, BD_SC_READY); /* Get next BD. */ - if (in_be16(&bdp->status) & BD_SC_WRAP) + if (ioread16be(&bdp->status) & BD_SC_WRAP) bdp = qe_port->tx_bd_base; else bdp++; @@ -414,7 +414,7 @@ static void qe_uart_start_tx(struct uart_port *port) container_of(port, struct uart_qe_port, port); /* If we currently are transmitting, then just return */ - if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX) + if (ioread16be(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX) return; /* Otherwise, pump the port and start transmission */ @@ -479,14 +479,14 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port) */ bdp = qe_port->rx_cur; while (1) { - status = in_be16(&bdp->status); + status = ioread16be(&bdp->status); /* If this one is empty, then we assume we've read them all */ if (status & BD_SC_EMPTY) break; /* get number of characters, and check space in RX buffer */ - i = in_be16(&bdp->length); + i = ioread16be(&bdp->length); /* If we don't have enough room in RX buffer for the entire BD, * then we try later, which will be the next RX interrupt. @@ -497,7 +497,7 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port) } /* get pointer */ - cp = qe2cpu_addr(bdp->buf, qe_port); + cp = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port); /* loop through the buffer */ while (i-- > 0) { @@ -519,7 +519,7 @@ error_return: /* This BD is ready to be used again. Clear status. get next */ clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV | BD_SC_ID, BD_SC_EMPTY); - if (in_be16(&bdp->status) & BD_SC_WRAP) + if (ioread16be(&bdp->status) & BD_SC_WRAP) bdp = qe_port->rx_bd_base; else bdp++; @@ -578,8 +578,8 @@ static irqreturn_t qe_uart_int(int irq, void *data) u16 events; /* Clear the interrupts */ - events = in_be16(&uccp->ucce); - out_be16(&uccp->ucce, events); + events = ioread16be(&uccp->ucce); + iowrite16be(events, &uccp->ucce); if (events & UCC_UART_UCCE_BRKE) uart_handle_break(&qe_port->port); @@ -610,17 +610,17 @@ static void qe_uart_initbd(struct uart_qe_port *qe_port) bdp = qe_port->rx_bd_base; qe_port->rx_cur = qe_port->rx_bd_base; for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) { - out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT); - out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); - out_be16(&bdp->length, 0); + iowrite16be(BD_SC_EMPTY | BD_SC_INTRPT, &bdp->status); + iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf); + iowrite16be(0, &bdp->length); bd_virt += qe_port->rx_fifosize; bdp++; } /* */ - out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT); - out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); - out_be16(&bdp->length, 0); + iowrite16be(BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT, &bdp->status); + iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf); + iowrite16be(0, &bdp->length); /* Set the physical address of the host memory * buffers in the buffer descriptors, and the @@ -631,9 +631,9 @@ static void qe_uart_initbd(struct uart_qe_port *qe_port) qe_port->tx_cur = qe_port->tx_bd_base; bdp = qe_port->tx_bd_base; for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) { - out_be16(&bdp->status, BD_SC_INTRPT); - out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); - out_be16(&bdp->length, 0); + iowrite16be(BD_SC_INTRPT, &bdp->status); + iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf); + iowrite16be(0, &bdp->length); bd_virt += qe_port->tx_fifosize; bdp++; } @@ -643,9 +643,9 @@ static void qe_uart_initbd(struct uart_qe_port *qe_port) setbits16(&qe_port->tx_cur->status, BD_SC_P); #endif - out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT); - out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); - out_be16(&bdp->length, 0); + iowrite16be(BD_SC_WRAP | BD_SC_INTRPT, &bdp->status); + iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf); + iowrite16be(0, &bdp->length); } /* @@ -667,21 +667,21 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port) ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX); /* Program the UCC UART parameter RAM */ - out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); - out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); - out_be16(&uccup->common.mrblr, qe_port->rx_fifosize); - out_be16(&uccup->maxidl, 0x10); - out_be16(&uccup->brkcr, 1); - out_be16(&uccup->parec, 0); - out_be16(&uccup->frmec, 0); - out_be16(&uccup->nosec, 0); - out_be16(&uccup->brkec, 0); - out_be16(&uccup->uaddr[0], 0); - out_be16(&uccup->uaddr[1], 0); - out_be16(&uccup->toseq, 0); + iowrite8(UCC_BMR_GBL | UCC_BMR_BO_BE, &uccup->common.rbmr); + iowrite8(UCC_BMR_GBL | UCC_BMR_BO_BE, &uccup->common.tbmr); + iowrite16be(qe_port->rx_fifosize, &uccup->common.mrblr); + iowrite16be(0x10, &uccup->maxidl); + iowrite16be(1, &uccup->brkcr); + iowrite16be(0, &uccup->parec); + iowrite16be(0, &uccup->frmec); + iowrite16be(0, &uccup->nosec); + iowrite16be(0, &uccup->brkec); + iowrite16be(0, &uccup->uaddr[0]); + iowrite16be(0, &uccup->uaddr[1]); + iowrite16be(0, &uccup->toseq); for (i = 0; i < 8; i++) - out_be16(&uccup->cchars[i], 0xC000); - out_be16(&uccup->rccm, 0xc0ff); + iowrite16be(0xC000, &uccup->cchars[i]); + iowrite16be(0xc0ff, &uccup->rccm); /* Configure the GUMR registers for UART */ if (soft_uart) { @@ -715,30 +715,30 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port) #endif /* Disable rx interrupts and clear all pending events. */ - out_be16(&uccp->uccm, 0); - out_be16(&uccp->ucce, 0xffff); - out_be16(&uccp->udsr, 0x7e7e); + iowrite16be(0, &uccp->uccm); + iowrite16be(0xffff, &uccp->ucce); + iowrite16be(0x7e7e, &uccp->udsr); /* Initialize UPSMR */ - out_be16(&uccp->upsmr, 0); + iowrite16be(0, &uccp->upsmr); if (soft_uart) { - out_be16(&uccup->supsmr, 0x30); - out_be16(&uccup->res92, 0); - out_be32(&uccup->rx_state, 0); - out_be32(&uccup->rx_cnt, 0); - out_8(&uccup->rx_bitmark, 0); - out_8(&uccup->rx_length, 10); - out_be32(&uccup->dump_ptr, 0x4000); - out_8(&uccup->rx_temp_dlst_qe, 0); - out_be32(&uccup->rx_frame_rem, 0); - out_8(&uccup->rx_frame_rem_size, 0); + iowrite16be(0x30, &uccup->supsmr); + iowrite16be(0, &uccup->res92); + iowrite32be(0, &uccup->rx_state); + iowrite32be(0, &uccup->rx_cnt); + iowrite8(0, &uccup->rx_bitmark); + iowrite8(10, &uccup->rx_length); + iowrite32be(0x4000, &uccup->dump_ptr); + iowrite8(0, &uccup->rx_temp_dlst_qe); + iowrite32be(0, &uccup->rx_frame_rem); + iowrite8(0, &uccup->rx_frame_rem_size); /* Soft-UART requires TX to be 1X */ - out_8(&uccup->tx_mode, - UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1); - out_be16(&uccup->tx_state, 0); - out_8(&uccup->resD4, 0); - out_be16(&uccup->resD5, 0); + iowrite8(UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1, + &uccup->tx_mode); + iowrite16be(0, &uccup->tx_state); + iowrite8(0, &uccup->resD4); + iowrite16be(0, &uccup->resD5); /* Set UART mode. * Enable receive and transmit. @@ -866,9 +866,9 @@ static void qe_uart_set_termios(struct uart_port *port, struct ucc_slow __iomem *uccp = qe_port->uccp; unsigned int baud; unsigned long flags; - u16 upsmr = in_be16(&uccp->upsmr); + u16 upsmr = ioread16be(&uccp->upsmr); struct ucc_uart_pram __iomem *uccup = qe_port->uccup; - u16 supsmr = in_be16(&uccup->supsmr); + u16 supsmr = ioread16be(&uccup->supsmr); u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */ /* Character length programmed into the mode register is the @@ -966,10 +966,10 @@ static void qe_uart_set_termios(struct uart_port *port, /* Update the per-port timeout. */ uart_update_timeout(port, termios->c_cflag, baud); - out_be16(&uccp->upsmr, upsmr); + iowrite16be(upsmr, &uccp->upsmr); if (soft_uart) { - out_be16(&uccup->supsmr, supsmr); - out_8(&uccup->rx_length, char_length); + iowrite16be(supsmr, &uccup->supsmr); + iowrite8(char_length, &uccup->rx_length); /* Soft-UART requires a 1X multiplier for TX */ qe_setbrg(qe_port->us_info.rx_clock, baud, 16); @@ -1139,7 +1139,9 @@ static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l) { struct device_node *np; const char *soc_string; +#ifdef CONFIG_PPC_85xx unsigned int svr; +#endif unsigned int soc; /* Find the CPU node */ @@ -1156,10 +1158,12 @@ static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l) if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc) return 0; +#ifdef CONFIG_PPC_85xx /* Get the revision from the SVR */ svr = mfspr(SPRN_SVR); *rev_h = (svr >> 4) & 0xf; *rev_l = svr & 0xf; +#endif return soc; } @@ -1202,7 +1206,7 @@ static void uart_firmware_cont(const struct firmware *fw, void *context) static int ucc_uart_probe(struct platform_device *ofdev) { struct device_node *np = ofdev->dev.of_node; - const unsigned int *iprop; /* Integer OF properties */ + u32 val; const char *sprop; /* String OF properties */ struct uart_qe_port *qe_port = NULL; struct resource res; @@ -1285,10 +1289,10 @@ static int ucc_uart_probe(struct platform_device *ofdev) /* Get the UCC number (device ID) */ /* UCCs are numbered 1-7 */ - iprop = of_get_property(np, "cell-index", NULL); - if (!iprop) { - iprop = of_get_property(np, "device-id", NULL); - if (!iprop) { + ret = of_property_read_u32_index(np, "cell-index", 0, &val); + if (ret) { + ret = of_property_read_u32_index(np, "device-id", 0, &val); + if (ret) { dev_err(&ofdev->dev, "UCC is unspecified in " "device tree\n"); ret = -EINVAL; @@ -1296,12 +1300,12 @@ static int ucc_uart_probe(struct platform_device *ofdev) } } - if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) { - dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop); + if ((val < 1) || (val > UCC_MAX_NUM)) { + dev_err(&ofdev->dev, "no support for UCC%u\n", val); ret = -ENODEV; goto out_free; } - qe_port->ucc_num = *iprop - 1; + qe_port->ucc_num = val - 1; /* * In the future, we should not require the BRG to be specified in the @@ -1345,13 +1349,13 @@ static int ucc_uart_probe(struct platform_device *ofdev) } /* Get the port number, numbered 0-3 */ - iprop = of_get_property(np, "port-number", NULL); - if (!iprop) { + ret = of_property_read_u32_index(np, "port-number", 0, &val); + if (ret) { dev_err(&ofdev->dev, "missing port-number in device tree\n"); ret = -EINVAL; goto out_free; } - qe_port->port.line = *iprop; + qe_port->port.line = val; if (qe_port->port.line >= UCC_MAX_UART) { dev_err(&ofdev->dev, "port-number must be 0-%u\n", UCC_MAX_UART - 1); @@ -1381,31 +1385,31 @@ static int ucc_uart_probe(struct platform_device *ofdev) } } - iprop = of_get_property(np, "brg-frequency", NULL); - if (!iprop) { + ret = of_property_read_u32_index(np, "brg-frequency", 0, &val); + if (ret) { dev_err(&ofdev->dev, "missing brg-frequency in device tree\n"); ret = -EINVAL; goto out_np; } - if (*iprop) - qe_port->port.uartclk = *iprop; + if (val) + qe_port->port.uartclk = val; else { /* * Older versions of U-Boot do not initialize the brg-frequency * property, so in this case we assume the BRG frequency is * half the QE bus frequency. */ - iprop = of_get_property(np, "bus-frequency", NULL); - if (!iprop) { + ret = of_property_read_u32_index(np, "bus-frequency", 0, &val); + if (ret) { dev_err(&ofdev->dev, "missing QE bus-frequency in device tree\n"); ret = -EINVAL; goto out_np; } - if (*iprop) - qe_port->port.uartclk = *iprop / 2; + if (val) + qe_port->port.uartclk = val / 2; else { dev_err(&ofdev->dev, "invalid QE bus-frequency in device tree\n"); |