5 files changed, 62 insertions, 50 deletions

diff --git a/include/linux/pinctrl/consumer.h b/include/linux/pinctrl/consumer.h
index 4aad3ce..18eccef 100644
--- a/include/linux/pinctrl/consumer.h
+++ b/include/linux/pinctrl/consumer.h
@@ -40,6 +40,25 @@ extern int pinctrl_select_state(struct pinctrl *p, struct pinctrl_state *s);
 extern struct pinctrl * __must_check devm_pinctrl_get(struct device *dev);
 extern void devm_pinctrl_put(struct pinctrl *p);
 
+#ifdef CONFIG_PM
+extern int pinctrl_pm_select_default_state(struct device *dev);
+extern int pinctrl_pm_select_sleep_state(struct device *dev);
+extern int pinctrl_pm_select_idle_state(struct device *dev);
+#else
+static inline int pinctrl_pm_select_default_state(struct device *dev)
+{
+	return 0;
+}
+static inline int pinctrl_pm_select_sleep_state(struct device *dev)
+{
+	return 0;
+}
+static inline int pinctrl_pm_select_idle_state(struct device *dev)
+{
+	return 0;
+}
+#endif
+
 #else /* !CONFIG_PINCTRL */
 
 static inline int pinctrl_request_gpio(unsigned gpio)
@@ -92,6 +111,21 @@ static inline void devm_pinctrl_put(struct pinctrl *p)
 {
 }
 
+static inline int pinctrl_pm_select_default_state(struct device *dev)
+{
+	return 0;
+}
+
+static inline int pinctrl_pm_select_sleep_state(struct device *dev)
+{
+	return 0;
+}
+
+static inline int pinctrl_pm_select_idle_state(struct device *dev)
+{
+	return 0;
+}
+
 #endif /* CONFIG_PINCTRL */
 
 static inline struct pinctrl * __must_check pinctrl_get_select(
@@ -158,47 +192,4 @@ static inline struct pinctrl * __must_check devm_pinctrl_get_select_default(
 	return devm_pinctrl_get_select(dev, PINCTRL_STATE_DEFAULT);
 }
 
-#ifdef CONFIG_PINCONF
-
-extern int pin_config_get(const char *dev_name, const char *name,
-			  unsigned long *config);
-extern int pin_config_set(const char *dev_name, const char *name,
-			  unsigned long config);
-extern int pin_config_group_get(const char *dev_name,
-				const char *pin_group,
-				unsigned long *config);
-extern int pin_config_group_set(const char *dev_name,
-				const char *pin_group,
-				unsigned long config);
-
-#else
-
-static inline int pin_config_get(const char *dev_name, const char *name,
-				 unsigned long *config)
-{
-	return 0;
-}
-
-static inline int pin_config_set(const char *dev_name, const char *name,
-				 unsigned long config)
-{
-	return 0;
-}
-
-static inline int pin_config_group_get(const char *dev_name,
-				       const char *pin_group,
-				       unsigned long *config)
-{
-	return 0;
-}
-
-static inline int pin_config_group_set(const char *dev_name,
-				       const char *pin_group,
-				       unsigned long config)
-{
-	return 0;
-}
-
-#endif
-
 #endif /* __LINUX_PINCTRL_CONSUMER_H */
diff --git a/include/linux/pinctrl/devinfo.h b/include/linux/pinctrl/devinfo.h
index 6e5f8a9..281cb91 100644
--- a/include/linux/pinctrl/devinfo.h
+++ b/include/linux/pinctrl/devinfo.h
@@ -28,6 +28,10 @@
 struct dev_pin_info {
 	struct pinctrl *p;
 	struct pinctrl_state *default_state;
+#ifdef CONFIG_PM
+	struct pinctrl_state *sleep_state;
+	struct pinctrl_state *idle_state;
+#endif
 };
 
 extern int pinctrl_bind_pins(struct device *dev);
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index 6aa2380..bf7e989 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -29,12 +29,25 @@
  *	if for example some other pin is going to drive the signal connected
  *	to it for a while. Pins used for input are usually always high
  *	impedance.
+ * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it
+ *	weakly drives the last value on a tristate bus, also known as a "bus
+ *	holder", "bus keeper" or "repeater". This allows another device on the
+ *	bus to change the value by driving the bus high or low and switching to
+ *	tristate. The argument is ignored.
  * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
  *	impedance to VDD). If the argument is != 0 pull-up is enabled,
- *	if it is 0, pull-up is disabled.
+ *	if it is 0, pull-up is total, i.e. the pin is connected to VDD.
  * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
  *	impedance to GROUND). If the argument is != 0 pull-down is enabled,
- *	if it is 0, pull-down is disabled.
+ *	if it is 0, pull-down is total, i.e. the pin is connected to GROUND.
+ * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based
+ *	on embedded knowledge of the controller hardware, like current mux
+ *	function. The pull direction and possibly strength too will normally
+ *	be decided completely inside the hardware block and not be readable
+ *	from the kernel side.
+ *	If the argument is != 0 pull up/down is enabled, if it is 0, the
+ *	configuration is ignored. The proper way to disable it is to use
+ *	@PIN_CONFIG_BIAS_DISABLE.
  * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
  *	low, this is the most typical case and is typically achieved with two
  *	active transistors on the output. Setting this config will enable
@@ -57,14 +70,14 @@
  *	setting pins to this mode.
  * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
  *	which means it will wait for signals to settle when reading inputs. The
- *	argument gives the debounce time on a custom format. Setting the
+ *	argument gives the debounce time in usecs. Setting the
  *	argument to zero turns debouncing off.
  * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
  *	supplies, the argument to this parameter (on a custom format) tells
  *	the driver which alternative power source to use.
  * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
- * 	this parameter (on a custom format) tells the driver which alternative
- * 	slew rate to use.
+ *	this parameter (on a custom format) tells the driver which alternative
+ *	slew rate to use.
  * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power
  *	operation, if several modes of operation are supported these can be
  *	passed in the argument on a custom form, else just use argument 1
@@ -78,8 +91,10 @@
 enum pin_config_param {
 	PIN_CONFIG_BIAS_DISABLE,
 	PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
+	PIN_CONFIG_BIAS_BUS_HOLD,
 	PIN_CONFIG_BIAS_PULL_UP,
 	PIN_CONFIG_BIAS_PULL_DOWN,
+	PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
 	PIN_CONFIG_DRIVE_PUSH_PULL,
 	PIN_CONFIG_DRIVE_OPEN_DRAIN,
 	PIN_CONFIG_DRIVE_OPEN_SOURCE,
diff --git a/include/linux/pinctrl/pinconf.h b/include/linux/pinctrl/pinconf.h
index 1ad4f31..f699869 100644
--- a/include/linux/pinctrl/pinconf.h
+++ b/include/linux/pinctrl/pinconf.h
@@ -30,7 +30,7 @@ struct seq_file;
  * @pin_config_set: configure an individual pin
  * @pin_config_group_get: get configurations for an entire pin group
  * @pin_config_group_set: configure all pins in a group
- * @pin_config_group_dbg_set: optional debugfs to modify a pin configuration
+ * @pin_config_dbg_parse_modify: optional debugfs to modify a pin configuration
  * @pin_config_dbg_show: optional debugfs display hook that will provide
  *	per-device info for a certain pin in debugfs
  * @pin_config_group_dbg_show: optional debugfs display hook that will provide
diff --git a/include/linux/pinctrl/pinctrl.h b/include/linux/pinctrl/pinctrl.h
index 2c2a9e8..5979147 100644
--- a/include/linux/pinctrl/pinctrl.h
+++ b/include/linux/pinctrl/pinctrl.h
@@ -49,7 +49,8 @@ struct pinctrl_pin_desc {
  * @name: a name for the chip in this range
  * @id: an ID number for the chip in this range
  * @base: base offset of the GPIO range
- * @pin_base: base pin number of the GPIO range
+ * @pin_base: base pin number of the GPIO range if pins == NULL
+ * @pins: enumeration of pins in GPIO range or NULL
  * @npins: number of pins in the GPIO range, including the base number
  * @gc: an optional pointer to a gpio_chip
  */
@@ -59,6 +60,7 @@ struct pinctrl_gpio_range {
 	unsigned int id;
 	unsigned int base;
 	unsigned int pin_base;
+	unsigned const *pins;
 	unsigned int npins;
 	struct gpio_chip *gc;
 };