| Age | Commit message (Collapse) | Author |
|---|
|
sata_sil is about to get a brand new interrupt handler. Add relevant
constants.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
ata_hsm_move() will be used by LLDDs which depend on standard PIO HSM
but implement their own interrupt handlers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
In some cases, hardreset must be followed by SRST.
* some controllers can't classify with hardreset
* some controllers can't wait for !BSY after hardreset (LLDD should
explicitly request followup softreset by returning -EAGAIN)
* (later) PM needs SRST w/ PMP==15 to operate after hardreset
To handle above cases, this patch implements follow-up softreset.
After a hardreset, ata_eh_reset() checks whether any of above
conditions are met and do a follow-up softreset if necessary.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
With hotplug, every reset might be a probing reset and thus something
similar to probe_init() is needed. prereset() method is called before
a series of resets to a port and is the counterpart of postreset().
prereset() can tell EH to use different type of reset or skip reset by
modifying ehc->i.action.
This patch also implements ata_std_prereset(). Most controllers
should be able to use this function directly or with some wrapping.
After hotplug, different controllers need different actions to resume
the PHY and detect the newly attached device. Controllers can be
categorized as follows.
* Controllers which can wait for the first D2H FIS after hotplug.
Note that if the waiting is implemented by polling TF status, there
needs to be a way to set BSY on PHY status change. It can be
implemented by hardware or with the help of the driver.
* Controllers which can wait for the first D2H FIS after sending
COMRESET. These controllers need to issue COMRESET to wait for the
first FIS. Note that the received D2H FIS could be the first D2H
FIS after POR (power-on-reset) or D2H FIS in response to the
COMRESET. Some controllers use COMRESET as TF status
synchronization point and clear TF automatically (sata_sil).
* Controllers which cannot wait for the first D2H FIS reliably.
Blindly issuing SRST to spinning-up device often results in command
issue failure or timeout, causing extended delay. For these
controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT
(currently 8s) to give newly attached device time to spin up, then
issues reset. Note that failing to getting ready in ATA_SPINUP_WAIT
is not critical. libata will retry. So, the timeout needs to be
long enough to spin up most devices.
LLDDs can tell ata_std_prereset() which of above action is needed with
ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags. These flags
are PHY-specific property and will be moved to ata_link later.
While at it, this patch unifies function typedef's such that they all
have named arguments.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
With hotplug, PHY always needs to be debounced before a reset as any
reset might find new devices. Extract PHY waiting code from
sata_phy_resume() and extend it to include SStatus debouncing. Note
that sata_phy_debounce() is superset of what used to be done inside
sata_phy_resume().
Three default debounce timing parameters are defined to be used by
hot/boot plug. As resume failure during probing will be properly
handled as errors, timeout doesn't have to be long as before.
probeinit() uses the same timeout to retain the original behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Hotplug will be implemented in libata-eh.c. Make ata_dev_read_id()
and ata_dev_configure() global.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
It's best to run ATA hotplug from EH but attaching SCSI devices needs
working EH. ata_aux_wq is used to give SCSI hotplug operations a
separate context.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Add device persistent field dev->sdev and store the attached SCSI
device. With hotplug, libata needs to know the attached SCSI device
to offline and detach it, but scsi_device_lookup() cannot be used
because libata will reuse SCSI ID numbers - dead but not gone devices
(due to zombie opens, etc...) interfere with the lookup.
dev->sdev doesn't hold reference to the SCSI device. It's cleared
when the SCSI device goes away.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Add ap->hw_sata_spd_limit and initialize it once during the boot
initialization (or driver load initialization). ap->sata_spd_limit is
reset to ap->hw_sata_spd_limit on hotplug. This prevents spd limits
introduced by earlier devices from affecting new devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Convert direct sdev -> dev lookup to __ata_scsi_find_dev().
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Separate out ata_find_dev() and __ata_scsi_find_dev() from
ata_scsi_find_dev(). These will be used by later hotplug
implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Lifetimes of some fields span over device plugging/unplugging. This
patch moves such persistent fields to the top of ata_device and
separate them with ATA_DEVICE_CLEAR_OFFSET. Fields above the offset
are initialized once during host initializatino while all other fields
are cleared before hotplugging. Currently ->ap, devno and part of
flags are persistent.
Note that flags is partially cleared while holding host_set lock.
This is to synchronize with later warm plug implementation which will
record hotplug request in dev->flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Move initialization of struct ata_device into ata_dev_init() in
preparation for hotplug. This patch calls ata_dev_init() from
ata_host_init() and thus makes no functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Add hotplug related flags and eh_info/context fields.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Implement ata_eh_wait(). On return from this function, it's
guaranteed that the EH which was pending or in progress when the
function was called is complete - including the tailing part of SCSI
EH. This will be used by hotplug and others to synchronize with EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Nudge host flag constants to make a room after ATA_FLAG_EH_PENDING.
New EH flag will be added.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Set ata_device->pio_mode to XFER_PIO_0 after a successful reset. This
is to keep EH resets consistent with probe resets as updated by the
commit b6079ca409bf88c248992e96510dd6f610f7ed89. Note that, with
soon-to-follow hotplug update, EH resets will include probe resets.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
This patch sets the prerequisites for the new debugging scheme that more or
less resembles Donald Becker's net driver example. This one liner doesn't
change any functionality beside setting the appropriate debug level for the
msg_enable control in the ata_port struct, which will be later used by the
ata_msg_* macros to control the amount of debug information sent to printk.
Signed-off-by: <petkov@uni-muenster.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] the latest consensus libata resume fix
|
|
A typo crept in with commit ea1e847cc202e805769c3c46ba5e5c53714068a1
which defined TI_LOCAL_FLAGS to be the offset of the `flags' field
of struct thread_info, rather than the `local_flags' field. This
fixes it. The typo was pointed out by Guennadi Liakhovetski.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Conflicts:
drivers/scsi/libata-core.c
|
|
Okay, just to sum things up.
This forces libata to wait for up to 2 seconds for BUSY|DRQ to clear
on resume before continuing.
[jgarzik adds...] During testing we never saw DRQ asserted, but
nonetheless (a) this works and (b) testing for DRQ won't hurt.
Signed-off-by: Mark Lord <liml@rtr.ca>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: fix RTC/NVRAM accesses on Maple
[PATCH] ppc32 CPM_UART: various fixes for pq2 uart users
[PATCH] powerpc: linuxppc64.org no more
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
These IDs are also used by the drivers/ide/pci changes submitted by
VIA.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Previous fix patches added a bunch of trailing whitespace,
which git-applymbox complained loudly about.
|
|
This is the second lcs driver patch containing the rest of lcs fixes.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Several problems occured with lcs device driver:
- device not operational anymore after cable pull/plug-in.
- unpredictable results occured, e.g. kernel panic
using cards of type QD8F.
- STOPLAN and delete multicast address command
were not proper recognized by OSA card under heavy network workload.
- channel/device error checks missing in interrupt handler.
To fix all problems at once recovery of lcs devices has been improved.
missing error checks in lcs interrupt handler has been added.
Once a hardware problem occurs lcs will recover the device now properly.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: Frank Blaschka <Frank.Blaschka@de.ibm.com>
From: Frank Pavlic <fpavlic@de.ibm.com>
- fix fake_ll during initial device bringup. fake_ll was
not active after first start of the device.
Problem only occured when qeth was built without IPV6 support.
- avoid skb usage after invocation of qeth_flush_buffers,
because skb might already be freed.
- remove yet another useless netif_wake_queue in
qeth_softsetup_ipv6 since this function is only called
when device is going online. In this case card->state will
never be in state UP. So let the net_device queue down .
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
From: Frank Pavlic <fpavlic@de.ibm.com>
- correct checking of sscanf-%n value in qeth_string_to_ipaddr().
- don't use netif_stop_queue outside the hard_start_xmit routine.
Rather use netif_tx_disable.
- don't call qeth_netdev_init on a recovery.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
In case of a parse error for the cu3088 group attribute,
return -EINVAL instead of count.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
During a code scan for another change I discovered that this call to
pcnet32_free_ring must be removed. If the open fails due to a lack of
memory all the ring structures are removed via the call to free_ring
and a subsequent call to open will dereference a null pointer in
pcnet32_init_ring.
Please apply to 2.6.17.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
(cherry picked from c653e6351e371b33b29871e5eedf610ffb3be037 commit)
|
|
|
|
Add back ->data_xfer and ->mode_filter to ata_piix.c.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: dev.c comment fixes
[IPV6] ROUTE: Don't try less preferred routes for on-link routes.
[IRDA]: *_DONGLE should depend on IRTTY_SIR
[MAINTAINERS]: Add entry for netem
|
|
Noticed that dev_alloc_name() comment was incorrect, and more spellung
errors.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In addition to the real on-link routes, NONEXTHOP routes
should be considered on-link.
Problem reported by Meelis Roos <mroos@linux.ee>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix section mismatch warnings:
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:arlan_probe from .text between 'init_module' (at offset
0x3526) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:init_arlan_proc from .text between 'init_module' (at offset
0x3539) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.exit.text:cleanup_arlan_proc from .text between 'cleanup_module' (at
offset 0x356c) and 'arlan_diagnostic_info_string'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix section mismatch warning:
WARNING: drivers/net/wireless/wavelan.o - Section mismatch: reference to
.init.text: from .text between 'init_module' (at offset 0x371e) and
'cleanup_module'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The TPM chip on the ThinkPad T60 and Z60 machines is returning 0xFFFF for
the vendor ID which is a check the driver made to double check it was
actually talking to the memory mapped space of a TPM. This patch removes
the check since it isn't absolutely necessary and was causing device
discovery to fail on these machines.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
WARNING: drivers/i2c/busses/scx200_acb.o - Section mismatch: reference to
.init.text: from .text after 'scx200_add_cs553x' (at offset 0x528)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix compile bug with the S3C24XX SPI driver when CONFIG_PM is set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
For a very long time, echoing 'standby' or 'mem' into /sys/power/state has
killed the machine on powerpc. This patch fixes that.
This patch adds the .valid callback to pm_ops on PowerMac so that only the
suspend to disk state can be entered. Note that just returning 0 would
suffice since the upper layers don't pass PM_SUSPEND_DISK down, but we
handle it there regardless just in case that changes.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If affs_bread() fails, the exit path calls mark_buffer_dirty_inode() with a
NULL argument.
Coverity CID: 312.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This improves accuracy of the touchscreen and hwmon sensor readings,
addressing an issue noted by Imre Deak: there's an extra bit written before
the sample (12 bits) gets written out.
It also catches up to various comments, and makes the /proc/interrupts
entry sensible again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Some driver wants to use CMSPAR, but it was missing on alpha and powerpc.
This adds it, with the same value as every other architecture uses.
(akpm: fixes the build of an upcoming gregkh USB patch)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
