| Age | Commit message (Collapse) | Author |
|---|
|
We can control renesas_usbhs driver as 2 way which are
autonomy mode and external IRQ trigger mode.
Autonomy mode is very easy settings for platform,
but it required USB power domain always ON,
since its connection/disconnection IRQ come from it.
If platform uses external IRQ trigger mode,
USB power domain can be OFF, since its
connection/disconnection IRQ come from external IRQ.
This patch enable external IRQ mode.
Now it is possible to add USB support on A4SP domain.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
* renesas-r8a7740:
ARM: shmobile: r8a7740: add A4LC pm domain support
ARM: shmobile: r8a7740: add A3SP pm domain support
ARM: shmobile: r8a7740: add A4S pm domain support
ARM: shmobile: r8a7740: fixup: MSEL1CR 7bit control
ARM: shmobile: soc-core: add R-mobile PM domain common APIs
ARM: mach-shmobile: Convert sh_clk_mstp32_register to sh_clk_mstp_register
|
|
This patch adds basic A4LC pm domain support.
Now, below devices can be controled by PM
MERAM, LCDC, VOU, ICBS, SDENC-Link
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch adds basic A3SP pm domain support.
Now, below devices can be controled by PM
DMAC1/2/3, IPMMU, DDM, FLCTL, SYS-HPB, BBIF1, MSIOF1/2,
SCIFA,SCIFB, IIC1, IrDA, USBH, USBDMAC, SDHI0/1/2, TPU,
DREQPAK (Sys), MMCIF, RSPI, SIM, USBF
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch adds basic A4S pm domain support.
Now, below devices can be controled by PM
Common-SHwy, Common-HPB, BSC, MFI, MMFROM, HS-SHwy,
SYS-HPB, INTCA, DBSC, DDRPHY (Logic),
ATAPI, GbEther, AXI-bus
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
MSEL1CR 7bit selects IRQ7 source pin which was
VBUS pin or A21/MSIOF0_RSYNC/MSIOF1_TSYNC pin.
But current pfc-r8a7740 MSEL1CR 7bit setting was wrong.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
* renesas-soc-core:
ARM: shmobile: soc-core: add R-mobile PM domain common APIs
ARM: mach-shmobile: Convert sh_clk_mstp32_register to sh_clk_mstp_register
Conflicts:
arch/arm/mach-shmobile/clock-r8a7740.c
|
|
This patch adds Renesas R-mobile series common PM domain APIs.
R-mobile CPU can use/switch this API
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
sh_clk_mstp32_register is deprecated. This convert to sh_clk_mstp_register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
On armadillo800eva provide a 3.3V supply for its SD/MMC-card interfaces.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch switch over to use common extra gpio method,
and reduced a waste of code on SH-ARM.
But these functions should be replaced by correct
gpio function in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It is possible to reduce CPU load if USB used DMAEngine.
This patch enabled it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It is possible to reduce CPU load if SDHI used DMAEngine.
This patch enabled it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It is possible to reduce CPU load if FSI playback used DMAEngine.
This patch enabled it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch enable HDMI sound support on CON3
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch enable sound support on CON11
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
* renesas-r8a7740:
ARM: shmobile: use common DMAEngine definitions on r8a7740
ARM: shmobile: r8a7740: add DMAEngine support for USB
ARM: shmobile: r8a7740: add DMAEngine support for SDHI
ARM: shmobile: r8a7740: add DMAEngine support for FSI
ARM: shmobile: add common DMAEngine definitions
ARM: shmobile: add common extra gpio functions
|
|
This patch switch over to use common DMAEngine definitions,
and reduced a waste of code.
It is easy to understand if sh_dmae_pdata / sh_dmae_slave_config
settings are used defined value instead of direct value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Current shdmac can support USB DMAC on r8a7740.
This support reduce CPU duty when USB access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Current shdmac can support SDHI DMAC on r8a7740.
This support reduce CPU duty when SDHI access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Current shdmac can support FSI DMAC on r8a7740.
This support reduce CPU duty when sound was playback.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
* renesas-soc-core:
ARM: shmobile: add common DMAEngine definitions
ARM: shmobile: add common extra gpio functions
|
|
Current shmobile have DMAEngine specific settings on each CPU code,
but SH-ARM DMAC use same value.
This patch adds new dma-register.h header to share definitions
and reduce a waste of code on SH-ARM architecture.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Current gpio frame work doesn't have the method to control
just pull up/down/free, but some SH-ARM boards need such kind of operation.
This patch adds common extra gpio functions for SH-ARM.
But these functions should be replaced by correct
gpio function in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch enable camera support on CON1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch enable HDMI support on CON3.
And removed unnecessary CONFIG_SYSFS_DEPRECATED_xxx config.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
In order to enable FSI-B selection from platform board,
this patch adds its interface to GPIO framework.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
r8a7740 FSI can select its parent clock,
and its selection is dependent on platform board.
In order to enable FSI parent selection from platform board,
this patch adds its interface to clock framework.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It is required from sh_mobile_ceu_camera driver.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
r8a7740 chip has lasting errata on MERAM buffer, and this patch adds
its work-around on setup-r8a7740.c
It solved CEU/VIO6C/2D-DMAC/VCP1/VPU5F/JPU/DISP memroy access error.
But MERAM driver can't control this issue,
since this work-around requires access to non-MERAM register address.
So, This it will be called as board specific code at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
In order to enable HDMI GPIO selection from platform board,
this patch adds its interface to GPIO framework.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It is required from sh_mobile_hdmi driver.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It is required from sh_mobile_hdmi driver.
This patch is based on v1.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
SDHI0 card-detect GPIO IRQ on mackarel currently works, because it is the
default configuration of IRQ26. However, we should not rely on this and
should configure the function explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Build failed, when SMP is enabled and EMEV2 is not enabled.
arch/arm/mach-shmobile/built-in.o: In function `shmobile_platform_cpu_kill':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:62: undefined reference to `emev2_platform_cpu_kill'
arch/arm/mach-shmobile/built-in.o: In function `shmobile_smp_get_core_count':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:39: undefined reference to `emev2_get_core_count'
arch/arm/mach-shmobile/built-in.o: In function `shmobile_smp_prepare_cpus':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:53: undefined reference to `emev2_smp_prepare_cpus'
arch/arm/mach-shmobile/built-in.o: In function `platform_secondary_init':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:78: undefined reference to `emev2_secondary_init'
arch/arm/mach-shmobile/built-in.o: In function `boot_secondary':
/home/iwamatsu/work/kernel/sh-2.6-devel/arch/arm/mach-shmobile/platsmp.c:90: undefined reference to `emev2_boot_secondary
This is the cause by when EMEV2 is disabled, that the check by OF of EMEV2 is
performed in platsmp.c.
This patch revise what the function about EMEV2 may not be used in this file,
when EMEV2 is not enabled.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
chclr_write() will use (chan_reg + chclr_offset).
In sh7372 case, DMA1CHCLR is started from 0xfe008220,
and chan_reg is started from 0xfe008020 (= sh7372_dmae0_resources).
Thus, chclr_offset should be (0x220 - 0x20) instead of 0x220.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
681e1b3eeb3606e06a7c4984e8058df84296f8bb
(ARM: mach-shmobile: sh73a0 DMA Engine support for SY-DMAC)
adds SY-DMAC, but it is 218, not 318
This patch is based on v2.0 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The clocksource driver is pure hardware enablement and the skew option
is default off, well tested and non dangerous."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Move skew_tick option into the HIGH_RES_TIMER section
clocksource: em_sti: Add DT support
clocksource: em_sti: Emma Mobile STI driver
clockevents: Make clockevents_config() a global symbol
tick: Add tick skew boot option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
|
|
The STI hardware is based on a single 48-bit 32kHz
counter that together with two individual compare
registers can generate interrupts. There are no
timer operating modes selectable which means that
the timer can not clear on match.
This driver is providing clocksource support for the
48-bit counter. Clockevents are also supported using
the same timer in oneshot mode.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: horms@verge.net.au
Cc: arnd@arndb.de
Cc: johnstul@us.ibm.com
Cc: rjw@sisk.pl
Cc: lethal@linux-sh.org
Cc: gregkh@linuxfoundation.org
Cc: olof@lixom.net
Link: http://lkml.kernel.org/r/20120525070344.23443.69756.sendpatchset@w520
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten for
the better support of "implicit feedback". If anything about USB got
broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up
immediately at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital
links between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal
routing through components with tight sequencing and formatting
constraints within their internal paths or where there are multiple
components connected with CPU managed DMA controllers inside the
SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like
digital basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
Texas Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be sent
slightly later as partly depending on the changes of DRM."
Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree). Also some
fairly trivial context conflicts in the imx and mcx soc drivers.
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: snd-usb: fix stream info output in /proc
ALSA: pcm - Add proper state checks to snd_pcm_drain()
ALSA: sh: Fix up namespace collision in sh_dac_audio.
ALSA: hda/realtek - Fix unused variable compile warning
ASoC: sh: fsi: enable chip specific data transfer mode
ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
ASoC: sh: fsi: use same format for IN/OUT
ASoC: sh: fsi: add fsi_version() and removed meaningless version check
ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
ASoC: tegra: Add machine driver for WM8753 codec
ALSA: hda - Fix possible races of accesses to connection list array
ASoC: OMAP: HDMI: Introduce codec
ARM: mx31_3ds: Add sound support
ASoC: imx-mc13783 cleanup
mx31moboard: Add sound support
ASoC: mc13783 codec cleanups
ASoC: add imx-mc13783 sound support
ASoC: Add mc13783 codec
mfd: mc13xxx: add codec platform data
ASoC: don't flip master of DT-instantiated DAI links
...
|
|
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
|
|
Use DT_MACHINE_START() on the emev2 based KZM9D board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Update the SMP glue code to use OF for matching.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This is EMEV2 DT support V3. The support is limited to
whatever devices that are complied in the kernel. At this
point we have UARTs handled by "em-uart" and a timer
handled by "em-sti". Clocks and SMP are not supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Tie in the on-board Ethernet controller on KZM9D
and make use of the GPIO controller for external
IRQ pin support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Tie in the Emma Mobile GPIO driver "em-gio" to
support the GPIOs on Emma Mobile EV2.
A static IRQ range is used to allow boards to
hook up their platform devices to the GPIOs.
DT support is still on the TODO for the GPIO driver,
so only platform device support is included here.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This is V3 of Emma Mobile EV2 SMP support.
At this point only the most basic form of SMP operation
is supported. TWD and CPU Hotplug support is excluded.
Tied to both the Emma Mobile EV2 and the KZM9D board
due to the need to switch on board in platsmp.c and
the newly introduced need for static mappings.
The static mappings are needed to allow hardware
acces early during boot when SMP is initialized.
This early requirement forces us to also map in
the SMU registers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
V3 of basic KZM9D board support. At this point a quite
thin layer that makes use of the Emma Mobile EV2 SoC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This is V3 of the Emma Mobile EV2 SoC support.
Included here is support for serial and timer
devices which is just about enough to boot a kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Current IRQ16-IRQ31 irq number are located around 800 from
1ee8299a9ec1ce5137a044c7768293007b9a3267
(ARM: mach-shmobile: Use 0x3400 as INTCS vector offset)
But, the PINT0/1 IRQ number are also located around 800 from
0df1a838d678fc6ab49f983a19e905f6a42297a0
(ARM: mach-shmobile: sh73a0 PINT IRQ base fix)
This patch relocates PINT0/1 IRQ number to around 700 where is not used,
and adds current IRQ location table in comment area.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
